Club Kart (Card Replacement Interface System) Manual
Club Kart: European Session (Rev D) (Sega, 2001) · Manual · 29 pages · 19 sections · original scan
www.seuservice.com
Bs
ADDENDUM to the OWNER’S MANUAL
CARD READER REPLACEMENT INSTALLATION INSTRUCTIONS
STANDARD & DELUXE VERSION
Push button to
Select Race Class
SEGA ENTERPRISES, INC. USA
PART NO. 999-1367
VISIT OUR WEBSITE!
_ OSegaServicecom
Forward — Refresh Deer eE (> http://www seuservice.com/
Dari's Ottice Game Manuals Seerenh What's New
BERRY people have visited this page since 3/16/01
bean yale Ifyou have any questions or comments Service Department
Brenig ns about this site please E-Mail to Darl Davidson@seu sega com
fax 415.701.0604
THis WER BUTE POWERED OY
WebSTAR 4-3
‘ ‘i " i wate i ins Non fr;
You will need the sh items to view this = in its entirety
AllPlatforms Windows Macintosh
Warranty
Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.
Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.
Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.
Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.
This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.
TABLE OF CONTENTS
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
TABLE OF CONTENTS
CLUB KART STANDARD
- CARD READER REPLACEMENT INSTALLATION
INSTRUCTION FOR STANDARD GAME ONLY ....
- DESIGNED RELATED PARTS
- PLACEMENT OF DECALS ..
- PARTS LIST
CLUB KART DELUXE
- CARD READER REPLACEMENT INSTALLATION
INSTRUCTION FOR STANDARD GAME ONLY ....
- DESIGNED RELATED PARTS
- PLACEMENT OF DECALS ..
- PARTS LIST
- WIRING DIAGRAM ....
HOW TO USE THIS ADDENDUM BOOKLET
Please read and understand instructions
completely before attempting this procedure
procedure.
This booklet is designed to be used with the original service manual iss game. It conti difications to both the wiring diagrams and parts assemblies detailed within the Parts Lists section of your service manual.
Card Reader Replacement
Installation
Instructions for STANDARD
Game Only
a be
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
club kart standard
Card Reader Replacement Installation Instruction for Standard Game Only
STEP 1
- Turn OFF power to the Club Kart game and unplug AC from the Power Outlet.
- Using the Key, open the Card Reader Compartment.
- Carefully remove both VHR 6P Connectors and JST 5P Connectors at the Card Reader Filter BD (The Filter BD, Sega P/N 837-13844 is located on the right of the Card Reader).
- Remove the Earth Ground Wire (Green Wire), and unplug the Power Supply Harness going to the Opto Coupler.
INSIDE CARD READER BOX REMOVE THESE CONNECTORS FROM FILTER BD
DISCONNECT THESE
PHOTO 5
club kart standard
STEP 2
- Using a T27 Tamper Proof Wrench (Provided with your game at time of shipment), unscrew the 4 Tamper Proof Bolts that secure the Card Reader Box to the Game. (Save these bolts for use later!!)
- Carefully remove the Card Reader Harness from the metal compartment.
REMOVE THESE 4 BOLTS 'T27 TAMPER PROOF) SAVE FOR USE LATER!!
PHOTO 6a
STEP 3
- At the Cabinet Card Reader opening, carefully pull the Green Ground Wire until the White Connector is exposed.
PULL UNTIL THIS CONNECTOR APPEARS. (NOTE: BLUE WIRE TO BE ATTACHED IN STEP 4
PHOTO 6b
club kart standard
STEP 4
1.
2.
CIRCULAR OPENING| Remove the Card Reader Replacement Unit from its shipping carton.
Unwind the Blue Wires (Twisted Approximately 86” long). Attach the end of the Blue Wires with tape to the Green Ground Wire exposed in Step 3 (Near White Connectors. This leaves enought length in the Green Wire to pull it back into place after it is used to guide the Blue Wires into place).
The Earth Ground Wire is only being used as a convenient means to guide the new Blue Wires into place. Care must be taken not to damage the wire, or separate the connector. It will need to be used as a ground for the Button Panel to ground it.
TAPE BLUE WIRES HERE
PHOTO 7a
From the back of the game, just below the NAOMI 2 Game BD, there is a 4” circular opening for the game harnesses. At this opening, very carefully pull the Green Ground Wire until the Blue Wires you taped become exposed.
Remove the tape to separate both Blue Wire from the Green Ground Wire. Gently pull on the Blue Wires to expose enough wire to go to the I/O BD ( The I/O BD is located at the upper left of the electronics area of the back of the game).
Pull the Green Wire carefully back into position for attachment to the Button Plate.
PHOTO 7c
club kart standard
STEP 5
- On the I/O BD, locate CN7 Pin 9 (Blue Wire).
- Using a pair of Wire Cutters, cut the Blue Wire from CN7 approximately 3” from the Connector. Strip off approximately 1/8” of the insulation off.
- Using a Bell Connector (provided) connect the Blue/White wire to the end of the Blue Wire that comes from the Wiper of the Accellerator Potentiometer.
- Connect the Blue Wire from the Twisted wires to the Blue Wire that goes to CN7 Pin 9.
WIRE TO BE CUT
PHOTO 8 a
WIRES CONNECTED WITH CRIMPS
PHOTO 8 b
club Kart Standard
STEP 6
- Plug JSPT P5 and J2 Connectors from the existing Card Reader Harness into the Card Reader Replacement Board. Attach the Earth Ground (Green Wire) to the Male Pem screw on the Button Panel. Secure with Screw. Be careful to ground yourself while handling this board.
CONNECT EARTH GROUND (GREEN WIRE)
PHOTO 9 a
- Secure the Button Panel to the Game Cabinet using the 4 Tamper Proof Bolts removed in Step 2.
PHOTO 9 b
PANEL INSTALLED ON THE GAME
If you require further assistance, contact your authorized SEGA DISTRIBUTOR, or SEGA TECHNICAL Services at (415) 701-6580 Mondays - Fridays 7:30am to 4:00pm(Pacific Standard Time)
DESIGNED RELATED PARTS
BUTTON PLATE DECAL 999-1354 Push button to Select Race Class
Novice |
- Beginner
Advanced
NO CARD DECAL _ 999-1358
Buttons Replace Card
Push button to Select Race Class
MONITOR DECAL - STD __ 999-1357
PLACEMENT OF DECALS
MONITOR DECAL - STD _ 999-1357,
NO CARD DECAL, 999-1358
BUTTON PLATE DECAL 999-1354
club kart Standard
CARD READER REPLACEMENT INSTALLATION KIT CONTAIN LIST
Description Locatrion
| 998-0150 | Printed Circuit Board Assy | Mounted to Button Plate | 1 |
| Local Purchase | 1.0k OHM 1/8W 5% Carbon Film Resistor | RI-R5, R10, R11, R13 | 7 |
| Local Purchase | Mzxim RS232A Line Driver | IC4 | 1 | |
| Local Purchase | T-1 Difused Red (LED) | LED 1 | 1 | |
| Local Purchase _[ Cap 1000UF 25V Elect FC Radial | C4,C5 | 2 | |
| Local Purchase | Cap 50V .luf Axial Ceramic Z5U | Cl, C2, C3, C6, C7, C8, C9, C10 | 8 | |
| Local Purchase | IC Quad Bilateral Switch (DIP) MC14066 | IC2 | 1 | |
| Local Purchase | ULN2003AN, | ICc3 | 1 | |
| Local Purchase _| 12 Pin In-Line Connector | Jl | 1 | |
| Local Purchase | Heat Sink | VRI | 1 | |
| [Local Purchase | 5 Position Header (B5P-SHF-1AA) | 33 | 1 | |
| Local Purchase | 6 Position Header (B6P-VH) | J2 | 1 | |
| 998-0151 | BS2p Stamp | IC] | 1 |
| Local Purchase _| Voltage +5 Volt Regulator | VRI | 1 | |
| 1999-1370 | HARNESS (Grand Products) | Main Harness connected to Button | 1 |
Plate
| Local Purchase | L-Bracket Small for Beeper (PCB Standoff) | Holder for Beeper | 1 | |
| 1999-1353 | Button Plate Blank | 1 | |
| Local Purchase | #6/32 X 3/8” Screw | Used to Assmbl PCB Button Plate | 6 | |
| Local Purchase | #6/32 Nut | Used to Assmbl PCB Button Plate | 3 | |
| Happ Ctrls | VLT PB MED REC Red, Red Cap 12V Lamp, DA3 MS | Button Plate | 1 |
| Happ Ctrls | VLT PB MED REC Blue, Blue Cap 12V Lamp. DA3 MS. | Button Plate | 1 |
| Happ Ctrls | VLT PB MED REC Green, Green Cap 12V Lamp, DA3 MS | Button Plate | 1 |
| Happ Ctrls | VLT PB MED REC Yellow, Yellow Cap 12V Lamp,DA3MS__| | Button Plate | 1 |
| Local Purchase | Piezoelectric Ceramic Buzzer Unit | Bl | 1 | |
| 999-1371 | Button Inserts N, B, A, S | Insert into Happ Buttons | 1 |
| 1999-1354 | Button Plate Decal | Placed on Metal Plate | 1 |
| 999-1352 | Angle Box STD Only | Under button Plate STd | 1 |
| Local Purchase | 1/2” X 8/32” Security Torx Screw (Black) | Used to Mount the Button Plate to |
the Angle Box 4
| 999-1357 | Monitor Bezel Decal - STD | Inside Monitor on Right Side | 1 |
| 999-1358 | Button Replace Card Decal - STD | Above the Coin Door | 1 |
| 999-1367 | CRIS Kit Installation/Owner’s Manual | 1 |
BUTTON PLATE - 999-1353 BUTTON PLATE 222-1253 | © oO
fe) O° O°
° °
° °
PRINTED CIRCUIT BOARD - 998-0150
ES 2001 RE
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Card Reader Replacement
Installation
Instructions for DELUXE
Game Only
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
club kart deluxe
Card Reader Replacement Installation Instruction for Deluxe Game Only
STEP 1
- Turn OFF power to the Club Kart Game and unplug AC from the Power Outlet.
- Using the Key, open the Card Reader Compartment.
- Carefully remove both VHR 6P Connectors and JST 5P Connectors at the Card Reader Filter BD (The Filter BD, Sega P/N 837-13844 is located on the right of the Card Reader).
- Remove the Earth Ground Wire (Green Wire), and unplug the Power Supply Harness going to the Opto Coupler.
INSIDE CARD READER BOX REMOVE THESE CONNECTORS FROM FILTER BD
- DISCONNECT THESE
PHOTO 17
STEP 2
- Remove Card Reader Replacement Unit from its Shipping Carton.
- Unwind the Blue Wires (Twisted approximately 86” long).
- Carefully feed the ends of the Twisted Blue Wires through the opening of the Card Reader Compartment and through opening in floor of the Sub Cabinet.
- Remove Front Lid from Sub Cabinet and pull the Blue Wires through until the end of the wires are able to reach the Naomi I/O BD ( The I/O BD is mounted in the Front of the machine near the Servo Diver Bd. ). note: USB Cable Connection to I/O Bd. Rev. A 11/15/01
club kart deluxe
STEP 3
- On the I/O BD, locate the CN7 Pin 9 (Blue Wire).
- Using a pair of wire cutters, cut the Blue Wire from CN7 approximately 3” from the Connector. Strip off approximately 1/8” of the insulation off.
- Using a Bell Connector (provided) connect the Blue/White Wire to the end of the Blue Wire that comes from the Wiper of the Accelerator Potentiometer.
- Connect the Blue Wire from the Twisted Wires to the Blue Wire that goes to CN7 Pin 9
WIRE TO BE CUT
PHOTO 18a
WIRES CONNECTED WITH CRIMPS
PHOTO 18 b
club kart deluxe
STEP 4
- Plug JSPT P5 and J2 Connectors from the existing Card Reader Harness into the Card Reader Replacement Board. Attach the Earth Ground (Green Wire) to the Male Pem screw on the Button Panel. Secure with screw. Be careful to ground yourself while handling this board.
(GREEN WIRE) PHOTO 19a
- Secure the Button Panel to the Game Cabinet using the 4 wood screws (provided).
- Push button to Select Race Class
Novice Beginner |
Advanced
PHOTO 19b
PANEL INSTALLED ON THE GAME
If you require further assistance, contact your authorized SEGA DISTRIBUTOR, or SEGA TECHNICAL Services at (415) 701-6580 Mondays - Fridays 7:30am to 4:00pm(Pacific Standard Time)
DESIGNED RELATED PARTS
Push button to BUTTON PLATE DECAL _ 999-1354
Select Race Class
LARGE NO CARD DECAL 999-1356
Push button to
COIN TOWER POP PANEL 999-1355
Push button to
PLACEMENT OF DECALS
= E
LARGE NO CARD DECAL MONITOR 999-1356
COIN TOWER POP PANEL, 999-1355,
BUTTON PLATE DECAL _ 999-1354.
club kart Deluxe
CARD READER REPLACEMENT INSTALLATION KIT CONTAIN LIST
Description Locatrion
| 1998-0150 | Printed Circuit Board Assy | Mounted to Button Plate | 1 |
| Local Purchase | 1.0k OHM 1/8W 5% Carbon Film Resistor | RI-R5,R10,R11, R13 | ij |
| [Local Purchase | Mzxim RS232A Line Driver | IC4 | 1 | |
| Local Purchase _| T-1 Difused Red (LED) | LED | | 1 | |
| Local Purchase_| | Cap 1000UF 25V Elect FC Radial | C4,C5 | 2 |
| (Local Purch | Cap 50V .luf Axial Ceramic Z5U | Cl, C2, C3, C6, C7, C8, C9, C10 | 8 |
| Local Purchase | IC Quad Bilateral Switch (DIP) MC14066 | IC2 | 1 | |
| (Local Purchase | | ULN2003AN | IC3 | i |
| Local Purchase | 12 Pin In-Line Connector | ul | I | |
| [Local Purchase | Heat Sink | VRI | 1 | |
| Local Purchase | 5 Position Header (B5P-SHF-1AA) | 33 | 1 | |
| [Local Purchase | 6 Position Header (B6P-VH) | J2 | 1 | |
| 1998-0151 | BS2p Stamp | ICl | 1 |
| [Local Purchase | Voltage +5 Volt Regulator | VRI | 1 | |
| 1999-1370 | HARNESS (Grand Products) | Main Harness connected to Button |
Plate 1
| Local Purchase | L-Bracket Small for Beeper (PCB Standoff) | Holder for Beeper | 1 | |
| 1999-1353 | Button Plate Blank | 1 | |
| Local Purchase | #6/32 X 3/8” Screw | Used to Assmbl PCB Button Plate | 6 | |
| Local Purchase | | #6/32 Nut | Used to Assmbl PCB Button Plate | 3 |
| [Happ Ctrls | VLT PB MED REC Red, Red Cap 12V Lamp, DA3 MS | Button Plate | 1 |
| [Happ Ctrls | VLT PB MED REC Blue, Blue Cap 12V Lamp, DA3 MS | Button Plate | 1 |
| [Happ Ctrls | VLT PB MED REC Green, Green Cap 12V Lamp, DA3 MS | Button Plate | 1 |
| Happ Ctrls | VLT PB MED REC Yellow, Yellow Cap 12V Lamp,DA3 MS __| Button Plate | 1 | |
| [Local Purchase | Piezoelectric Ceramic Buzzer Unit | Bl | 1 | |
| 1999-1371 | Button Inserts N,B, A, S | Insert into Happ Buttons | 1 |
| 1999-1354 | Button Plate Decal | Placed on Metal Plate | 1 |
| 1999-1360 | Black Filler Plate DLX Only | Behind Button Plate on DLX | 1 |
Local Purchase | 3/4” Phillips Button Head Black Wood Screw (DLX Mounting Only) 4
| 1999-1356 | Large NO CARD Decal | Placed at Lower Right of Monitor | 1 |
| 1999-1355 | Coin Tower POP Panel | Placed above the Coin Tower | 1 |
| 1999-1367 | CRIS Kit Installation/Owner’s Manual | 1 |
BUTTON PLATE - 999-1353
BLACK FILLER PLATE - 999-1360.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Jt = iié a Vee
Auf=E3 c? 4] MAX232A
Auf 5
= : Ic4
TxD [g- 2 | Gnd
I
| Yee 12 10 il 066 SWIS Clas Glyn 0 5 SW2A Class GIPn} © SW3 BClass 10 1K J) Pin; © al = 8} c2 9 9 < 4066 @1Pind) © 12 oe tL a7
| 17 | S$ Claselte | = |
18 AChss Be = © SClass Light (I pin 2)
| 19 | BChss lie | © | AClass Light (J1 pin3) |
| fn | wm |_|, | en | ace |
4 © Novice (1 pin 5)
Hukares 1 | H2vae Buzzer [5
PA Hyde out S Class Lite
A Class Lite
BCless Lite
Novice lite
SWI S Chss
SW2A Chss
SW3 B Class
SW4 Novice
POT IN
POTOUT
Switch. Ground oe el
‘club kart Card Reader Replacement Rev 4.01 10/25/01 drawn by:Al Vernon
SEGA ENTERPRISES, INC. (USA)
45133 Industrial Drive Fremont, CA 94538 (650) 632-7580 phone (650) 632-7594 fax