Ms Pac-Man
Ms. Pac-Man (Midway / General Computer Corporation, 1981) · Manual · 91 pages · 67 sections · original scan
JANUARY, 1982 Game Nos. 595, 602. & 599
MIDWAYS
Parts and Operating Manual woe scrcewenr ov NAMCO iro
No. 602 MINI
No. 599 COCKTAIL
10750 W. GRAND AVENUE FRANKLIN PARK, ILLINOIS 60131 No. 595 UPRIGHT is ve : USA
Phone: (312) 451-1360 Cable Address: MIDCO ‘Telex No.: 72-1596
Form No. 0595-00300-0000
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.
EypocUne, BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
E.
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
MIDWAY MFG. CO.
our TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER MIDWAY GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS. Continental U. S$. 800-323-7182 Illinois Only 1-800-942-0497
COPYRIGHT 1982 © BY MIDWAY MFG. CO. ALL RIGHTS RESERVED.
NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131
Printed In U.S.A.
DESCRIPTION TABLE OF CONTENTS
Introduction ...
Location and Setup Inspection Installation Self-Test .... Game Volume Adjustment Control Option Switch Settings Game Operation ...... Self-Test Mode . Attract Mode ... Ready-to-Play Mode Play Mode.........- Two Player Operation .
Maintenance and Repair Cleaning Fuse Replacement ........ Opening the Control Panel .. Removal of Main Display Glass and T.V. Bezel T.V. Monitor Replacement . Printed Circuit Board Replacement . Opening the Attraction Panel... Coin Door Maintenance
Mlustrated Parts Breakdown No. 595 — Ms. Pac-Man — Upright — Header Fluorescent Light Assy. No. 595 — Ms. Pac-Man — Upright — Header Fluorescent Light Assy. — Parts List . No. 595 — Ms. Pac-Man — Upright — Front............... 4-2 No. 595 — Ms. Pac-Man — Upright — Front — Parts List No. 595 — Ms. Pac-Man — Upright — Rear Access .. No. 595 — Ms. Pac-Man — Upright — Rear Access — No. 602 — Ms. Pac-Man — Mini — Front.............- No. 602 — Ms. Pac-Man — Mini — Front — Parts List.. No. 602 — Ms. Pac-Man — Rear Access No. 602 — Ms. Pac-Man — Rear Access — Parts List No. 599 — Ms. Pac-Man — Cocktail — Front .......... No. 599 — Ms. Pac-Man — Cocktail — Front — Parts List No. 599 — Ms. Pac-Man — Cocktail — Interior Access... No. 599 — Ms. Pac-Man — Cocktail — Interior Access — Parts List . Ms. Pac-Man — Transformer Board Assy. Ms. Pac-Man — Transformer Board Assy. — Front Door Assy. — U.S.A. 25¢ Front Door Assy. — U.S.A. 25¢ — Parts List . Ms. Pac-Man — Control Assy. — All Versions | Ms. Pac-Man — Control Assy. — All Versions — Parts List .
Vi.
Vil. TABLE OF CONTENTS (cont’d)
Technical Troubleshooting ................ 002. e cece cnet e tenet net e eee 5-1 Introduction General Suggestions ........ . 51 Harness Component Troubleshooting . - 5-1 Transformer and Line Voltage Problems ... - 5-2 A Glossary of Microprocessor Terms ..... : - 5-3 Introduction to the Z-80 CPU ..... . 53 General Purpose Registers . . : . 5-4 Arithmetic and Logic Unit (ALU) ...... 2.0.0.0. 2c cence nce een e neces 5-4 Instruction Register and CPU Control 2. O4 2-80 CPU Pin Description ©... 0... cece nnn ene ene 5-4
T.V. Monitor Manual .... 2.0.00. 0 cect ete teen ete e tetas Introduction 00.6... cence een beet eden eee e ee eeeees Symptom Diagnosis ...... Guide to Schematic Symbols Troubleshooting .. Theory of Operation .. Differences Between Monitors : Parts Interchangeability ............. Monitor Schematic — Wells-Gardner 19” . . Replacement Parts List — Wells-Gardner 19 Monitor Schematic — Electrohome 19” ..... Replacement Parts List — Electrohome 19” . Monitor Schematic — Electrohome 13” . . Replacement Parts List — Electrohome 13
Schematics and Wiring Diagrams Wiring Diagram w/ Credit Multiplier — Upright ...........0 00 cece cee cece eee nee eee 7-1 Wiring Diagram w/ Credit Multiplier Bypass — Upright +72 Wiring Diagram w/ Credit Multiplier — Mini........ : 73 Wiring Diagram w/ Credit Multiplier Bypass — Mini . 74 Wiring Diagram w/ Credit Multiplier — Cocktail . 75 Wiring Diagram w/ Credit Multiplier —. = Cocktail : 76 Game Logic Board — Component Layout . . 78 Game Logic Board — Schematic .......... 79 V-RAM Addresser Board — Component Layout . 7-10 V-RAM Addresser Board — Schematic ........ 7 2-80 Sync Buss Controler — Component Layout 7-12 Z-80 Sync Buss Controler — Schematic . . TAB Auxiliary Board — Component Layout . . . . 7-14 Auxiliary Board — Schematic ....... ‘ » 7-15 Filter Board — Component Layout . 7-16 Filter Board — Schematic ........ TAT Credit Multiplier Board — Component Layout . : . 7-18 Credit Multiplier Board — Schematic ......... 200.0. cece cece cece eee ene n eens 7-19
FIGURE
1 Assigned point values .. 2 Location of serial number, on/off switch, interlock switc! 3 Major sub-assemblies (cont. from FIG 2) 4 Interlock switch operation 5 Location of volume control & option switch ... 6 Option switch settings ...........--...s.eeeee 7 Identification of “on screen” graphics during play . 8 Location of fUSeS ......... cee eee eee eee eee e eee 9 Removing control panel — Upright & Mini games 10 Opening Cocktail game .........+-..se sees ant Removing control panel — Cocktail game . 12 Removing display glass — Upright game 13 Removing display glass — Mini game .. 14 Removing top glass — Cocktail game .. 15 Removing monitor — Upright game 16 Removing monitor — Mini game . 17 Opening Cocktail game ......... 18 Removing monitor — Cocktail game . 19 Removing printed circuit boards ... 20 Removing attraction panel — Upright game . 21 Replacing fluorescent starter — Upright game. 22 Replacing fluorescent light mounting bracket & speaker — 23 Removing attraction panel — Mini game .. 24 Replacing speaker — Mini game 25 Removing and replacing coin acceptor. . 26 Cleaning the metal coin acceptor .... 27 Lubricating the metal coin acceptor.. 28 Opening the plastic coin acceptor .......... 29 Changing the plastic coin acceptor to accept American or Canadian quarters 30 Changing difficulty level of game TABLE OF FIGURES
Ms. Pac-Man
IMPORTANT NOTE
DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and II of this manual completely. It will not take more than a few minutes and it may be very helpful.
I. Introduction
MS. PAC-MAN is a one or a two player game. There are three models: the “UPRIGHT”, “MINI”, and “COCKTAIL TABLE”. When the two player mode is selected on the Upright or Mini model, the players take turns at the controls to guide their player through the game course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it's your turn. When playing this game, you are in complete contro! of MS. PAC-MAN. She will go wherever you tell her to. And she just loves to eat dots. However, she doesn’t like the four ghosts, BLINKY (red), PINKY (pink), INKY(turquoise), and SUE (amber) because they feel the same way about her as she does about dots. BLINKY, PINKY, INKY, and SUE are four VERY SMART ghosts. They move very fast and seem to have a sixth sense which always lets them know exactly where MS. PAC-MAN is in the maze. They never give up in their pursuit of her. One of their favorite tricks is to divide and try to trap her between them. You really have to keep an eye on them. But MS. PAC-MAN can turn the tables on these four ghosts for short periods of time during each maze. All she has to do is let them get fairly close in their pursuit of her and then eat one of the four flashing ENERGIZER DOTS that every maze begins with (one close to each corner of the maze). When this happens, it causes the four ghosts to turn blue with fright no matter where they are in the maze. This is because they know that when she eats an ENER- GIZER DOT it gives MS. PAC-MAN the ability to eliminate them. However, she can ONLY eliminate them for as long as they are blue. The ghosts will only stay blue for a few seconds after MS. PAC-MAN eats an ENERGIZER DOT. But they do give a warning BEFORE they turn back to their original colors — they start to flash. As your skill level increases, the four ghosts speed up their pursuit of MS. PAC-MAN and they stay blue for shorter and shorter periods of time after she eats an ENERGIZER DOT until, in the high number mazes, they do not turn blue at all. One bonus player (this is switch selectable) can be awarded to you as you reach or pass a certain preselected point value. The assigned point values for all items that can be eaten are as listed in Figure 1.
Major NewFeatures
A major new feature of your MS. PAC-MAN game is that there are four different mazes with varying numbers of exits and varying exit locations. The mazes are generally more difficult than that of PAC-MAN. Another major new feature is that the maze identifier symbols move throughout the maze and are thus more difficult to get.
Game Objective
The object of the game is to HAVE FUN and survive as long as possible while constantly improving your skills and eating as many dots and eliminating as many ghosts as you can. As you do this, each following maze will be harder and harder to complete.
OBJECT EATEN DOTS ENERGIZER DOTS 1ST GHOST 2ND GHOST 3RD GHOST 4TH GHOST CHERRIES STRAWBERRY ORANGE PRETZEL APPLE PEAR BANANA POINT VALUE 10 POINTS EACH 50 POINTS EACH 200 POINTS 400 POINTS 800 POINTS 1600 POINTS 100 POINTS 200 POINTS 500 POINTS 700 POINTS 1000 POINTS 2000 POINTS 5000 POINTS
Figure 1 Assigned point values
II. Location and Setup
INSPECTION
- Remove the game from its shipping crate.
- Inspect the entire outside of it for any signs of damage. Any scratches? Dents? Cracks? Any broken controls? Any broken glass or plastic? Just look it over closely and make a note of any signs of damage. . Remove the shipping cleats from the bottom of the cabinet. . Install the four levelers, one at each corner of the cabinet. ¢ Level the cabinet. . Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2. ® Also check to make sure all plug-in connectors on the wire harness are firmly seated.
¢ Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. Make sure all printed circuit boards (P.C.B.’s) are firmly seated in their connectors. See Figure 2. These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged.
- Make a note of any problems that can’t be easily corrected.
- Call your distributor and/or service man about your problem list.
2-1 INSTALLATION
- Location requirements: Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz Temperature: 32° to 100°F (0° to 38°C) Humidity: Not over 95% relative Space required: Upright 25” x 33” (63 x 84cm) Mini 20” x 24” (50 x 60cm) Cocktail 32" x 22” (81 x 55cm) Game height: Upright 70” (175cm) Mini 61” (153cm) Cocktail 29” (73cm) . Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
. Interlock and power ON/OFF switches. See Figure 2. © To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models). @ When any access door is opened, the interlock switch installed there turns off all power to the game. Check each operation. interlock switch for proper
POWER SUPPLY AND GAME BD. UPRIGHT
SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER)
CONTROL PANEL (PLAYER 1).
POWER SUPPLY AND GAME BD.
INTERLOCK SWITCH (INSIDE COIN DOOR) ON/OFF teres act xr SERIAL Betis ~€ 4 SERIAL NUMBER F*-. ene NUMBER
INTERLOCK Tw. SWITCH MONITOR
INTERLOCK ‘SWITCH
TRANSFORMER BOARD ASSY TRANSFORMER i (NOT SEEN) BOARD ASSY (NOT SEEN)
POWER SUPPLY AND GAME BD.
CONTROL PANEL (PLAYER 2)
TRANSFORMER BOARD ASSY
ON/OFF SWITCH (LOCATED UNDER GAME ON
COCKTAIL PLAYER 2 SIDE)
Figure 2 Location of serial number, on/off switch, interlock switch & major sub-assemblies
2-2
UPRIGHT
Figure 3 Major sub-assemblies (cont. from FIG 2)
After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 2. Turn the game on and ailow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test.
2-3 When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 4.
Figure 4 Interlock switch operation
SELF-TEST Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game's speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).
wesons & GAME VOLUME ADJUSTMENT CONTROL. See Figure 5. The game volume control pot is located on the game logic board assembly. There is only one pot. For adjustment, it may be reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you will have to open the table top to reach it. To make the sounds louder, turn the pot in a clockwise direction (~~). To make the sounds less loud, turn the pot in a counterclockwise direction (#7).
VOLUME ADJUSTMENT
LOUDER
OPTION SWITCH
Figure 5 Location of volume control & option switch
2-4
OPTION SWITCH SETTINGS
To change the option switch settings, you DO NOT have to take the Main Game Logic Board out of the game. They can be easily reached through the rear access door on the Upright and Mini models. On the Cocktail Table modal, you do have to open the table top to reach them. When changing any options, ALWAYS put the game into the Self-Test mode, make your changes, check the results on the monitor screen, take the game out of the Self-Test mode, and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen:) The option Switch settings and what they will make the game do are shown in Figure 6. See Figure 5 for option switch locations.
MS. PAC-MAN
OPTION SWITCH SETTINGS -
METHOD OF PLAY
SW#1 SW#2 SWH3 SW#4 SWHS SWHE SWH7 SWH8 ON ON OFF ON ON OFF OFF OFF FREE PLAY 1 COIN 1 PLAY 1 COIN 2 PLAYS 2COINS~ 1 PLAY
NUMBER OF MS. PAC-MEN PER GAME
1 MS. PAC-MAN 2 MS. PAC-MEN 3 MS. PAC-MEN 5 MS. PAC-MEN ON ON OFF ON ON OFF OFF OFF
BONUS MS. PAC-MEN
BONUS MS. PAC-MAN AT 10,000 POINTS BONUS MS. PAC-MAN AT 15,000 POINTS BONUS MS. PAC-MAN AT 20,000 POINTS NO BONUS ON ON OFF ON ON OFF OFF OFF
SPECIAL FUNCTIONS
AUTOMATIC RACK ADVANCE FREEZE VIDEO (MONITOR PRESENTATION STOPS MOVING) GAME OPERATES NORMALLY ON OFF
OFF ON OFF OFF
Figure 6 Option switch settings
Game Operation
MS. PAC-MAN is a one or a two player game with a color T.V. monitor. The game gives a display which has all the parts shown in Figure 7. The game has four possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, and SELF- TEST.
SELF-TEST MODE
The Self-Test mode is a special mode for checking the game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.
You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on. The test switch is located inside the coin door under the coin meter. When this is done, the game will react as follows:
- First, you will see random colored parts of the picture, then a moving pattern of white letters and numbers followed by moving multicolored patterns on the screen.
- Immediately following this, a rightside up test display is shown on the monitor screen. This will remain until you set the Self-Test switch back to the “OFF” position. This test display is shown below.
SELF-TEST DISPLAY AND BOARD LOCATION COORDINATES
MEMORY OK or (M-Rom-1/Bad C Ram-0/Bad W Ram-1/etc.) “1 COIN “1 CREDIT BONUS *15000 MS. PAC-MEN °3 UPRIGHT or (TABLE)
- = switch selectable
HIGH SCORE
HIGH 20860 PLAYER 1 SCORE
MS. PAC-MAN SCORE 20860 PLAYER 2 SCORE
ENERGIZER DoT
RACK IDENTIFIER SYMBOLS
Figure 7 Identification of “on screen” graphics during play
- If a bad ROM or RAM is found by the game's “MEMORY OK” message. The following table internal check system during the Self-Test, the translates the chip location codes into actual game indicates this to you by showing the loca- positions on the game logic P.C. Board. tion code of the bad chip(s) in place of the
DISPLAY DESCRIPTION
MEMORY OK All RAMs are good. BAD V RAM-O RAM located on Logic PC board at position 4K is bad. BAD V RAM-1 RAM located on Logic PC board at position 4N is bad. BAD C RAM-O RAM located on Logic PC board at position 4L is bad. BAD C RAM-1 RAM located on Logic PC board at position 4P is bad. BAD W RAM-O RAM located on Logic PC board at position 4M is bad. BAD W RAN-1 RAM located on Logic PC board at position 4R is bad.
MEMORY OK All ROMs are good. M-ROM-O ROM located on Logic PC board at position 6E is bad. M-ROM-1 ROM located on Logic PC board at position 6F is bad. M-ROM-2 ROM located on Logic PC board at position 6H is bad. M-ROM-3 ROM located on Logic PC board at position 6J is bad.
4, The detection of bad components on the Auxiliary table lists the components that are on this Auxil- Logic PC Board is not quite as simple as is the iary PC Board and what symptoms they will cause case for the Main Logic PC Board. The following to appear on the monitor when each is bad.
BAD COMPONENT SYMPTOM DISPLAYED ON MONITOR (GAME IS NOT IN SELF-TEST)
2-80 CPU STATIONARY color garbage (parts of pictures) CPU located on auxiliary PC board at position U4
E-ROM-O Game goes through warm-up routine over & over & over... ROM located on Auxiliary PC board at position U5
E-ROM-1 Game goes through warm-up routine over & over. & over... ROM located on Auxiliary PC board at position U6
E-ROM-2 FLASHING color garbage (parts of pictures) ROM located on Auxiliary PC board at position U7
CUSTOM CHIP Monitor screen reads out “ROM 0” CG-820 With game in Self-Test — Screen reads “BAD ROM 0” CG-820 located on Auxiliary PC board at position UO
Monitor screen displays FLASHING color garbage (parts of pictures) CG-821 located on Auxiliary PC board at position U1 CUSTOM CHIP CG-821
CUSTOM CHIP Screen display is same as for CG-821 CG-822 With game in Self-Test — Screen reads out UPSIDEDOWN “BAD W RAM-O” CG-822 located on Auxiliary PC board at position U2
CUSTOM CHIP Screen display is same as for CG-821 CG-823 CG-823 located on Auxiliary PC board at position U3
2-7
- To check your game function switches and but- ¢ Across hatch pattern appears on the monitor tons (coin counter switches, TEST CREDIT but- screen for about 2 seconds. ton, 1 PLAYER and 2 PLAYER buttons): activate ¢ If you wish to keep this test pattern on the each one while the game is in the Self-Test mode. monitor screen for further use, slide Self-Test You should hear a game sound for eacn activa- switch back to the “ON” position after the cross tion. If you do not hear it, the switch/button is hatch appears and before it disappears. either not working, miswired, or disconnected. © When finished with the cross hatch pattern, set Check it out thoroughly. the Self-Test switch to the “OFF” position.
- When finished with the Self-Test mode, slide the © Normal game functions will now return to the Self-Test switch back to the “OFF” position. monitor screen. Deen
ATTRACT MODE
- The Attract mode starts: e Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.) e After a Self-Test has been completed. (Performing a Self-Test sets the credits in the game's memory to zero “O".) e After a play has been finished and there are no more credits left in the game’s memory. e In the Attract mode, the game will give the following displays centered on the monitor screen:
uP HIGH S oo 1UP - HIGH SCORE 2uP
#
CREDIT oO
DISPLAY 1 DISPLAY 2
2-8
dup HIGH Oo
M
CREDIT
DISPLAY 3
STARRING
MS PAC-MAN
if
CREDIT o
DISPLAY 5
2-9 1UP HIGH oo
Ld
CREDIT
DISPLAY 4
DISPLAY 6
No matter where the game is in the Attract mode sequence, it will immediately go to the following display as soon as a game has been Paid for. It will hold this display on the monitor screen until the "1 PLAYER” or the “2 PLAYER™ start button is pushed.
1UP «HIGH SCORE = 2UP oo
PUSH START BUTTON 1 PLAYER ONLY
appirtonar © 10000
a
CREDIT 4
DISPLAY 1
READY-TO-PLAY MODE
- The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game.
- The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed.
- In the Ready-To-Play mode. the game will give one of the above displays centered on the monitor screen.
- If no START button is pressed. the game will hold this display on the screen indefinitely.
PLAY MODE
- The Play mode begins when either the “1 PLAYER” or the “2 PLAYER” start button is pressed. “READY!” is displayed below the “GHOST HOUSE" on the screen
- The Play mode ends when your last MS. PAC- MAN has been eliminated. When this happens. “GAME OVER’ is written across the center of the monitor screen (below the “GHOST HOUSE").
- The game consists of four different mazes. Each maze has side exits. These vary in number and location on each of the four mazes. The mazes contain small dots in most of the passageways plus four flashing ENERGIZER DOTS (one near each corner of the maze). MS. PAC-MAN just loves to eat the dots in these passageways. Each maze also has a“GHOST HOUSE" at its center — maximum capacity, three ghosts at one time. Its door is on its top side (side farthest from player). 1uP HIGH SCORE 2uP oo
PUSH START BUTTON 1 OR 2 PLAYERS
CREDIT
DISPLAY 2
. At the beginning of each game, MS. PAC-MAN appears at the lower center of the maze while the four ghosts appear at the “GHOST HOUSE” BLINKY appears outside the door and PINKY. INKY, and SUE appear inside the “GHOST HOUSE”. . When play begins. BLINKY (who'd love to eliminate her) immediately begins looking for MS. PAC-MAN (who immediately begins eating dots just as fast as she can). As time passes. PINKY. INKY. and SUE (who'd also love to eliminate her) leave the “GHOST HOUSE” one at a time and begin looking for MS. PAC-MAN — who is still busily eating dots just as fast as YOU can steer her to them.
But with all four ghosts chasing her, it is not as easy to eat the dots (without being eliminated by a ghost) as it was earlier in the game. And BLINKY, PINKY, INKY, and SUE are four VERY SMART ghosts. For instance, they will divide up two, three, or four ways to try to trap MS. PAC-MAN between them, in a corner, or even in one of the tunnels. You've really got to watch them! It seems like they always have some sneaky new trick up their sleeves. However, if they get too close, MS. PAC-MAN can always eat one of the flashing ENERGIZER DOTS. When this happens, it causes all four ghosts to turn blue with fright no matter where
they are in the maze. This is because they know that when she eats an ENERGIZER DOT it gives MS. PAC-MAN the ability to eliminate them. But, she can ONLY eliminate them for as long as they are blue. And they will only stay blue for a short period of time. But the ghosts do give a warning BEFORE they turn back to their original colors — they start to flash. When MS. PAC-MAN eliminates a blue ghost, its point value appears on the monitor screen at the place where the ghost was eliminated while at the same time being added to your score, and the ghost disappears — all except for its eyes. The eyes go back to the “GHOST HOUSE” where they get another body of their original color. This done, “they leave the “GHOST HOUSE” again and take up their pursuit of MS. PAC-MAN once more.
When she eats the last dot of any particular maze: all movement stops immediately, the maze flashes, and the next maze appears. All the players are in the new maze when it appears. The word “READY!” is also there — right below the “GHOST HOUSE”. After a second or two passes, the word “READY!” disappears and play begins. You MUST eat all the dots in any particular maze in order to advance to the next one. The maze identifier symbols appear at the bottom edge of the monitor screen. As your skill level increases, the four ghosts speed up their pursuit of MS. PAC-MAN and they stay blue for shorter and shorter periods of time after she eats an ENERGIZER DOT until, in the high number mazes, they do not turn blue at all. One bonus player (this is switch selectable) can be awarded to you as you reach or pass a certain preselected point value. The assigned point values for all items that can be eaten are as listed in Figure 1. When one of the ghosts happens to eliminate one of your MS. PAC-MEN, assuming you have at least one remaining in reserve, the word “READY!” appears below the “GHOST HOUSE” at the same time one of your reserve MS. PAC- MEN appears at the lower center part of the maze. After a second or two passes, the word “READY!” disappears and play begins anew. When one of the ghosts eliminates your LAST MS. PAC-MAN, the words “GAME OVER” are displayed below the “GHOST HOUSE”, your score is displayed under “1 UP”, and in addition, if your score was the highest on this game to date, it will also be displayed under “HIGH SCORE” at the top center of the monitor screen. The game will then either go into the Ready-To-Play mode (if there are still credits left in its memory) or into the Attract mode (if there are no more credits left in its memory).
2-11 Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.
TWO PLAYER OPERATION The Upright, Mini, and Cocktail Table models all have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however.
- In the Upright and Mini models, the players must take turns at the controls. In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn.(When it is not your turn, your set of controls will have NO effect on the game.) . Your turn lasts until one of the ghosts eliminates your MS. PAC-MAN. At this point, the game will do one of several things depending on whether or not the eliminated MS. PAC-MAN was your last or if you still have others remaining in reserve. 2.
MS. PAC-MAN ELIMINATED — OTHERS REMAIN- ING IN RESERVE © The chase stops. © Next, the screen display changes to the screen display of the other player, it displays “READY!” under the "GHOST HOUSE” at the same time one of the other player's reserve MS. PAC-MEN. appears at the lower center of this maze. After a second or two passes, the word “READY!” disappears and play begins for the other player.
MS. PAC-MAN ELIMINATED — NO OTHERS RE- MAINING IN RESERVE ¢ Game displays the words “PLAYER ONE” or “PLAYER TWO” above the “GHOST HOUSE” and the words “GAME OVER” below the “GHOST HOUSE”. Your final score is displayed under “1 UP” or “2 UP”, depending upon which player you were. In addition, if your score was the highest on this game to date, it will also be displayed under “HIGH SCORE” at the top center of the monitor screen. After this, the screen display changes to the screen display of the other player, it displays “READY!” under the “GHOST HOUSE” at the same time one of the other player's reserve MS. PAC-MEN appears at the lower center of this maze. After a second or two passes, the word “READY!” disappears and play begins for the other player.
Ill. Maintenance and Repair
Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.
CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors, hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CAN NOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.
FUSE REPLACEMENT
This game contains several fuses located as shown in Figure 8.
- UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Transformer Board Assembly. . MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Transformer Board Assembly. . COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Transformer Board Assembly. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual.
See the T.V. Monitor Manual (available on request from your distributor or monitor manufacturer) and/ or the T.V. Troubleshooting Section of this manual for information on these fuses.
FUSES LOCATED ON TRANSFORMER BOARD ASSY (MECH. PANEL) (TYPICAL OF ALL VERSIONS)
Figure 8 Location of fuses
OPENING THE CONTROL PANEL. See Figure 9.
- UPRIGHT MODEL: 2. MINI MODEL: ¢ The contro! panel is held in place by three latches, one on the left side, one on the right side, and one on the front center. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhock them from their latch plates. ¢ To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the contro! panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. © To reinstall the control panel, reverse this procedure. e The control panel is held in place by two latches, one on the right side and one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the contro! panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The contro! panel is now free and can be removed. ¢ To reinstall the control panel, reverse this procedure.
UPRIGHT
Figure 9 Removing control panel — Upright & Mini games
Figure 10 Opening Cocktail game
- COCKTAIL TABLE MODEL:
© Each control panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 10.
Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 10.
Remove the screws which secure the control panel in place. See Figure 11. © To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. e To reinstall the control panel, reverse this procedure. REMOVE (2)
REMOVE (3) SCREWS ON BOTTOM OF SHELF
Figure 11 Removing control panel — Cocktail game
REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY
- UPRIGHT MODEL: See Figure 12. 2. MINI MODEL: See Figure 13.
Turn the power to the game off and remove the rear access door.
Remove the screws from the glass support bracket and lift it out the back of the cabinet.
Grasp the main-display-glass in the top center, lift up slightly and pull it out the rear of the cabinet.
Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed.
To reinstall the T.V. bezel assembly and the main-display-glass. reverse this procedure.
REMOVE (3) SCREWS AND REMOVE BRKT.
PULL DISPLAY GLASS OUT FROM REAR OF CABINET
Figure 12 Removing display glass — Upright game © Turn the power off to the game and remove the control panel. @ Remove the screws which secure the glass
- Clamping plate. © Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. © By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. Remove the screws which secure the T.V. bezel assembly and lift it out
e Reverse this procedure to reinstall the T.V. bezel assembly and the main-display-glass.
DISPLAY GLASS
CLAMPING PLATE
Figure 13 Removing display glass — Mini game
- COCKTAIL TABLE MODEL: See Figure 14.
Remove the screws which secure the table top glass clamps in place. e Remove the table top glass. © Lift out the T.V. bezel assembly. e To reinstall the T.V. bezel assembly and the table top glass, reverse this procedure.
Figure 14 Removing top glass — Cocktail game T.V. MONITOR REPLACEMENT
- UPRIGHT MODEL: See Figure 15. e Turn power off to the game.
© Open the rear access door. © Completely disconnect the T.V. monitor from all its cabling. DON 'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor. the maindisplay-glass and bezel MUST be removed. See above “Upright Model” procedure. With the removal of only four bolts, the T.V. monitor and its mounting channels will be loose. The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet's right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 15. To reinstall the T.V. monitor. reverse this procedure. After replacing the T.V. monitor. be sure to run the game Self-Test
- MINI MODEL: See Figure 16. Turn the power off to the game. Open the rear access door. Completely disconnect the T.V. monitor from all its cabling. DON T FORGET THE CHASSIS GROUND WIRE.
Before removing the T.V. monitor. the maindisplay-glass and bezel MUST be removed. See above “Mini Model” procedure. With the removal of only four nuts. the T.V monitor will be loose.
The monitor is removed by supporting it and pulling straight back as shown in Figure 16. To reinstall reverse this procedure.
After replacing the T.V. monitor, be sure to run the game Self-Test.
- COCKTAIL TABLE MODEL: See Figure 18. Tum power off to the game.
Open the coin box door and release the two latches indicated in Figure 17. the T.V. monitor,
REMOVE (4) BOLTS TO REMOVE MONITOR
Figure 15 Removing monitor — Upright game
© Once the latches are released, unhook them from their latch plates. e Grasp the table top at “A” and open it as indicated in Figure 17.
REMOVE (4) BOLTS TO REMOVE MONITOR
Figure 16 Removing monitor — Mini game
CLAMPS
Figure 17 Opening Cocktail game
Remove the screws which hold the table top glass clamps in place. Remove the table top glass. Lift out the T.V. bezel assembly. Completely disconnect the T.V. monitor from all its cabling. DON ’T FORGET THE CHASSIS GROUND WIRE. Remove the screws holding the T.V. monitor chassis to the “L” by the door hinge(s). See Figure 18. Close the Cocktail Table top and re-latch it. Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 18. Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both. Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL not to bump the neck of the picture tube. To reinstall the T.V. monitor, reverse this procedure. Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. After replacing the T.V. monitor, be sure to run the game Self-Test. REMOVE 6 SCREWS (3 EACH SIDE) AND LIFT MONITOR STRAIGHT UP-
REMOVE 4 SCREWS (2 EACH SIDE)
Figure 18 Removing monitor — Cocktail game
3-7
PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT
- UPRIGHT MODEL: See Figure 19. Turn the power to the game off.
Unlock and open the rear access door.
Disconnect the Main Game Logic Board from all its cabling. Disconnect the Auxiliary Game Logic Board from the Main Game Logic Board. Remove the P.C.B. clamps indicated in Figure 19 and slide the Main Game Logic Board out the back of the cabinet.
CAREFULLY pop the Auxiliary Game Logic Board off its four snap-in mounting posts and lift it out the back of the cabinet. To reinstall the above P.C.B.’s, reverse this procedure.
P.C.B. REMOVE CABLING
STANDOFFS
AUXILLIARY
- MINI MODEL: See Figure 19. © Turn the power off to the game.
Unlock and open the rear access door.
- Disconnect the Auxiliary Game Logic Board from the Main Game Logic Board. ® Remove the P.C.B. clamps indicated in Figure 19 and slide the Main Game Logic Board out the back of the cabinet. ¢ CAREFULLY pop the Auxiliary Game Logic Board off its four snap-in mounting posts and lift it out the back of the cabinet. © To reinstall the above P.C.B.’s, reverse this procedure.
|” STANDOFFS
AUXILLIARY P.C.B
a
P.C.B.
MAIN GAME LOGIC BOARD
REMOVE THIS SUPPORT
Figure 19 Removing printed circuit boards
- COCKTAIL TABLE MODEL: See Figure 19. © Turn the power off to the game.
Open the cabinet: Open the coin box door and release the two latches indicated in Figure 17.
Once they're released, unhook them from their latch plates. © Grasp the table top at “A” and open it as indicated in Figure 17.
¢ To remove the Main and Auxiliary Game Logic Boards. See Figure 19. Disconnect the Auxiliary Game Logic Board from the Main Game Logic Board. Remove the P.C.B. clamps indicated in Figure 19 and slide the Main Game Logic Board out of the cabinet. CAREFULLY pop the Auxiliary Game Logic Board off its four snap-in mounting posts and lift it out of the cabinet. See Figure 19. © To reinstall the above P.C.B.’s, reverse this procedure.
OPENING THE ATTRACTION PANEL
- UPRIGHT MODEL: See Figure 20. ¢ Turn the power to the game off.
® Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 20. Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. See Figure 20. To reinstall the attraction panel, reverse this procedure. ® The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
- Replacing the fluorescent tube starter. See Figure 21. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. ¢ Replacement of the fluorescent tube mounting bracket assembly. See Figure 22. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure. ¢ Replacing the speaker. See Figure 22. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker.
REMOVE SCREWS (USE SPECIAL WRENCH SHIPPED WITH YOUR GAME) Ne
LIFT ATTRACTION PANEL STRAIGHT UP
U
Figure 20 Removing attraction panel — Upright game
xyo™ 4 TURN TO REPLACE FLUORESCENT TUBE STARTER
Figure 21 Replacing fluorescent starter — Upright game
- MINI MODEL: See Figure 23. Turn the power off to the game.
Remove the screws from the top and bottom of the formed attraction panel. Remove the formed attraction panel by pulling it straight away from the cabinet. This exposes the attraction panel light bulbs and their mounting board. To service the light bulbs and their mounting board: Turn the power to the game back onso youcan see which bulbs are burnt out. Mark the burnt out bulbs and turn the power to the game back off again.
REMOVE SCREWS TO LIGHT BRKT.
REMOVE SPEAKER FROM FRONT OF GAME
Figure 22 Replacing fluorescent light mounting bracket & speaker — Upright game To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. To reinstall the above removed items, reverse this procedure.
Figure 23 Removing attraction panel — Mini game
3-10
- To replace the speaker. See Figure 24. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.
- THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL.
SPEAKER
Figure 24 Replacing speaker — Mini game
TO REMOVE PUSH LATCHES DOWN J
PLACE PEGS. IN SLOTS TO REPLACE PULL MECHANISM OUT COIN DOOR MAINTENANCE
METAL COIN ACCEPTOR MECHANISMS
Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
- Remove the coin acceptor mechanism as shown in Figure 25. e Push down on the two spring loaded latches. @ While holding the latches down, pull the top of the coin acceptor mechanism toward you. © Release the latches and lift out the coin acceptor mechanism.
- Clean the magnet of all foreign particles. See Figure 26. ¢ This may be accomplished by swinging the gate open as shown in the above figure.
- Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) © Also clean the pivot pin.
- Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: Place the coin acceptor in boiling water for about ten minutes.
PUSH MECHANISM IN
Figure 25 Removing and replacing coin acceptor
e Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. e Rinse the coin acceptor in clean boiling water. © Dry the coin acceptor thoroughly by usirig filtered compressed air to blow it dry.
- To lubricate the coin acceptor: @ Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 27. e Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 25.
- Place the two pegs at the coin acceptot’s base into their retaining slots.
GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE
Figure 26 Cleaning the metal coin acceptor « Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
PLASTIC COIN ACCEPTOR MECHANISMS The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
- Remove the coin acceptor mechanism(s) as shown in Figure 25. e Push down on the two spring loaded latches. While holding the latches down, pull the top of the acceptor mechanism toward you.
- Release the latches and lift out the mechanism.
- Squeeze the two pins indicated in Figure 28 together to open the mechanism and break it down into its three basic parts. Clean the mechanism in hot soapy water. It never rusts. © Rinse the mechanism in clean hot water and allow it to dry. e Reassemble the mechanism (it never needs lubrication).
APPLY POWDERED GRAPHITE HERE
UNDERSIZE LEVER
“E” RINGS
CRADLE
Figure 27 Lubricating the metal coin acceptor
3-12
SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN
HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT
Figure 28 Opening the plastic coin acceptor
- Check the coin chute for obstructions such as: 7. Close and lock the coin door. paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 25. © Place the two pegs at the coin acceptor’s base into their retaining slots.
- Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.
MAGNET
SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.
TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.
LEVEL OF DIFFICULTY MODIFICATION In order to increase the level of difficulty with which your MS. PAC-MAN game plays, a jumper wire must be installed as described below.
- Remove the Main Game Logic Board as described elsewhere in this manual.
- Remove the coating of green insulatory material over the two halves of the jumper pad shown in
Clo ETRY} DIP-SWITCH
123456718 ao\ bhh0000
SSS 2200uF 259
b 74LS/6/ Figure 30. BE CAREFUL NOT TO DAMAGE THE FOIL OF THE JUMPER PAD IN ANY WAY.
- Solder in a jumper wire connecting the two halves of the pad.
- When finished, reinstall the Main Game Logic Board as described elsewhere in this manual.
INSTALL JUMPER WIRE TO CONNECT BOTH HALVES OF INDICATED JUMPER PAD.
Figure 30 Changing difficulty level of game

This page is a drawing, shown as the original scan.
NO. 595 — MS. PAC-MAN — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY.
NO. 595 — MS. PAC-MAN — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY. — PARTS LIST
ORDER BY PART NUMBER ONLY
0595-00105-0000 FLUORESCENT BRKT. 0017-00003-0043 18" COOL WHITE FLUOR. LAMP 0017-00021-0005 FLUORESCENT LOCKS (2 REQ'D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ’D.) 0017-00003-0412 FLUOR. STARTER HOLDER W/LEADS 0017-00101-0573 #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ’D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00003-0019 FLUOR. STARTER 0017-00003-0026 BALLAST 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ'D.) A961-00042-0000 LINE FILTER ASSY. — NOT SHOWN
NO. 595 — MS. PAC-MAN — UPRIGHT — FRONT
NO. 595 — MS. PAC-MAN — UPRIGHT — FRONT — PARTS LIST
ITEM PART NO.
0595-00901 -OOXF 0537-00903-0057 0508-00104-00XF 0017-00101-0138 0017-00009-0522 A595-00011-0000 0017-00009-0393 0017-00003-0259 0017-00101-0127 0017-00103-0061 0508-00900-0000 0508-00905-0000 0508-00901-0000 0017-00101-0017 0595-00900-00XF 0508-00108-0000 0017-00101-0027 0595-00903-0000 A595-00007-00XF 0017-00101-0620 0017-00103-0061 0017-00101-0341 0508-00115-0000 0961-00115-00XF 0017-00009-0033 0595-00106-0100 0595-00106-0200 0555-00901-0000 0017-00101-0141 A595-00017-0000 A595-00005-0000 0017-00042-0260 0017-00032-0093 0017-00103-0054 A090-00300-07BK 0090-00002-04BK 0017-00101-0121 A595-00019-0000 0935-00906-0100 0017-00102-0048 0017-00103-0026 ORDER BY PART NUMBER ONLY
DESCRIPTION
DECORATIVE HEADER PLEX! — 23” x 9-1/16" x 3/16" GLASS CHANNEL — 7-5/8” LG. (2 REQ'D.) UPPER/LOWER HEADER RETAINER (2 REQ’D.) #8 x 5/8 TORX TAMPER RESISTANT SCR. (6 REQ’D.) LONG ARM KEY T-20 (FOR ABOVE SCREW) FLUORESCENT HEADER ASSY. BLACK SPEAKER GRILLE W/SLOTS 6” x 9" SPEAKER 8 OHM, 7W. #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ'D.) 19” C.R.T. BEZEL T.V. PLEXI-GLASS (SMOKED) — 17-3/8" x 13-1/4” x 1/8" PLEXI-GLASS CLIPS (4 REQ’D.) . #6 x 1/2 SLT. HEX HD. BLK. SCR. (4 REQ’D.) MAIN VIEWING GLASS — 23” x 21-1/8" x 3/16” GLASS STOP BRKT. #8 x 3/4 SLT. HEX HD. M.S. (3 REQ’D.) CONTROL SHELF DECORATIVE OVERLAY CONTROL SHELF PLATE W/STRIKE ASSY. #8-32 x 1/2 CARRIAGE BOLT (10 REQ’D.) #8-32 HEX NUT W/SEMS (10 REQ'D.) #6 x 1/4 PHIL. TRS. HD. SCR. (4 REQ’D.) CENTER CONTROL SHELF LOCK BRKT. STRIKE (2 REQ'’D.) LATCH CLAMP (3 REQ'D.) CONTROL SHELF MTG. BRKT. — RIGHT CONTROL SHELF MTG. BRKT. — LEFT LOCATING PIN (PLASTIC) (4 REQ'’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (14 REQ’D.) CONTROL SHELF CABLE ASSY. CONTROL ASSY. PUSH BUTTON ASSY. — WHITE (2 REQ'D.) PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) 5/8-11 PAL NUT (2 REQ'’D.) U.S.A. COIN DOOR ASSY. — 25¢ LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) COIN DOOR CABLE ASSY. KICK PLATE — 23” LG. 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)
NO. 595 — MS. PAC-MAN — UPRIGHT — REAR ACCESS
4-4
NO. 595 — MS. PAC-MAN — UPRIGHT — REAR ACCESS — PARTS LIST ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
A088-00013-0000 ON-OFF SWITCH & BRKT. ASSY. 0894-00916-0000 RECESSED HAND LIFT (2 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (12 REQ'D.) 0017-00003-0339 ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) 0017-00003-0401 WELLS-GARDNER — 19" COLOR DUAL SYNC. HORIZ. MTG. MONITOR A508-00005-0000 MONITOR MTG. CHANNEL ASSY. (2 REQ’D.) 0017-00102-0066 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (4 REQ’D.) 0017-00104-0014 7/8" DISH WASHER (4 REQ’D.) 0595-00104-0000 MONITOR RAIL (2 REQ'D.) 0017-00102-0002 1/4-20 x 1/2 SLT. HEX HD. BOLT (4 REQ'D.) 0017-00104-0014 7/8" DISH WASHER (4 REQ’D.) 0866-00120-0000 CHASSIS BRACE 0508-00106-0000 T.V. BEZEL MTG. BRKT. 0508-00900-0000 T.V. BEZEL A088-00015-0000 INTERLOCK SWITCH & BRKT. ASSY. A082-91375-B000 GAME LOGIC BOARD ASSY. 0624-00902-0100 P.C. SUPPORT BRKT. — 12” LG. (3 REQ’D.) 0624-00902-0300 P.C. SUPPORT BRKT. — 2-1/2" LG. 0624-00902-0500 P.C. SUPPORT BRKT. — 6-1/2" LG. 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (13 REQ’D.) 0017-00104-0037 #8 WASHER (13 REQ’D.) A084-91375-A595 PROGRAMMED MS. PAC-MAN BRD. ASSY. A595-00020-0000 AUXILIARY BOARD & BRKT. ASSY. A084-91415-B617 AUXILIARY P.C. BOARD ASSY. 0017-00042-0106 P.c. BRD. SUPPORT 0595-00107-0000 AUX. P.C. MTG. BRKT. A950-00004-0000 COIN BOX ASSY. A950-00006-0000 COIN BOX CRADLE ASSY. 0950-00105-0000 COIN BOX COVER 0950-00104-0000 COIN BOX HANDLE 0950-00101-0000 COIN DEFLECTOR (2 REQ'D.) 0950-00900-0000 LARGE PLASTIC CASH BOX 0017-00101-0142 1/4-20 x 1-3/8 BLACK RND. HD. BOLT (4 REQ'D.) 0017-00104-0014 7/8" DISH WASHER (4 REQ’D.) 0017-00103-0018 1/4-20 HEX NUT (4 REQ’D.) A961-00007-0000 CASTER ASSY. (2 REQ’D.) 0961-00109-0000 WHEEL BRKT. (2 REQ'D.) 0017-00042-0255 PLASTIC WHEEL (2 REQ'D.) 0894-00702-00XF SHAFT (2 REQ'D.) 0017-00100-0037 3/8" E-RING (2 REQ'D.) A866-00049-0000 LINE CORD ASSY.
ADDITIONAL PARTS LIST A097-00008-0000 BACK DOOR LOCK ASSY. 0017-00009-0490 5-5/8" SQR. VENT GRILLE — BACK DOOR (4 REQ'D.) A866-00036-0000 TEST SWITCH & BRKT. ASSY. A595-00014-0000 POWER CABLE ASSY. A595-00016-0000 LOW VOLTAGE CABLE ASSY. A595-00015-0000 MASTER CABLE ASSY. 3000-17246-1000 GROUND STRAP A595-00013-0000 TRANSFORMER BOARD ASSY. A932-00026-0000 FILTER BOARD ASSY. A082-91109-A000 CREDIT MULTIPLIER BY-PASS P.C. BOARD ASSY.
NO. 602 — MS. PAC-MAN — MINI — FRONT
NO. 602 — MS. PAC-MAN — MINI — FRONT — PARTS LIST
ITEM PART NO.
0602-00901-00XF 0017-00101-0138 0017-00009-0522 A555-00007-0000 0017-00031 -0030 0017-00003-0219 A514-00015-0000 0017-00009-0393 0017-00003-0259 0017-00101-0127 0017-00103-0061 0602-00900-00XF 0537-00903-0056 A555-00016-0000 0017-00101-0138 0602-00100-00XF 0602-00902-0000 0017-00101-0620 0017-00103-0061 0017-00101-0341 ORDER BY PART NUMBER ONLY
DESCRIPTION
DISPLAY HEADER #8 x 5/8 TORX TAMPER RESISTANT SCREW (8 REQ'D.) LONG ARM KEY T-20 (FOR ABOVE SCREW) INSERT DISPLAY. ASSY. WEDGE BASE LIGHT SOCKET (5 REQ’D.) #194 LAMP 14V., .27A. (5 REQ'D.) INSERT DISPLAY CABLE ASSY. BLACK SPEAKER GRILLE W/SLOTS 6" x 9" SPEAKER 8 OHM, 7W. #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ'D.) MAIN DISPLAY GLASS — 17-13/16" x 14-13/16" x 3/16” GLASS EDGE CHANNEL — 14-1/2" LG. (2 REQ'D.) GLASS CLAMPING PLATE ASSY. #8 x 5/8 TORX TAMPER RESISTANT SCREW (2 REQ'’D.) CONTROL SHELF PLATE DECORATIVE SHELF OVERLAY #8-32 x 1/2 CARRIAGE BOLT (8 REQ'D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) #6 x 1/4 PHIL. TRS. HD. SCREW (4 REQ'’D.) 0555-00101-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0555-00101-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 LOCATING PINS (4 REQ’D.) 0961-00115-O0XF 0017-00009-0033 0017-00101-0141 A595-00005-0000 A602-00010-0000 STRIKE (2 REQ'D.) LATCH CLAMP (2 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) CONTROL ASSY. CONTROL SHELF CABLE ASSY. 0017-00042-0260 PUSH BUTTON ASSY. — WHITE (2 REQ'’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (2 REQ'D.) 0017-00103-0054 5/8-11 PAL NUT (2 REQ'D.) U.S.A. DOUBLE COIN DOOR ASSY. — 25¢ LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) COIN DOOR CABLE ASSY. KICK PLATE — 17-15/16" LG. 3/8-16 x 2” LEG LEVELERS (4 REQ'D.) 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.) A090-00300-07BK 0090-00002-04BK 0017-00101-0121 A595-00019-0000 0935-00906-0400 0017-00102-0048 0017-00103-0026
4-7
NO. 602 — MS. PAC-MAN — MINI — REAR ACCESS
4-8
NO. 602 — MS. PAC-MAN — MINI — REAR ACCESS — PARTS LIST
0017-00003-0259 0017-00003-0340
0017-00003-0369
A926-00012-00XF 0017-00102-0066 0017-00104-0014 0017-00103-0018 0513-00101-0000 A514-00004-0000 0513-00900-0000 0934-00905-0000 A961-00026-0000 A088-00015-0000 A090-00300-07BK A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A082-91375-B000 0624-00902-0100 0624-00902-0300 0624-00902-0500 0017-00101-0141 0017-00104-0037 A084-91375-A595 A595-00020-0000 A084-91415-B617 0017-00042-0106 0595-00107-0000 A088-00013-0000
A097-00008-0000 0017-00009-0490 0926-00904-0000 0017-00101-0628 0017-00103-0061 A602-00007-0000 A602-00008-0000 A602-00009-0000 A866-00049-0000 3010-03003-0000 3000-17246-0800 A602-00006-0000 A932-00026-0000 A082-91109-A000 ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
6" x 9 SPEAKER 8 OHM, 7W. ELECTROHOME — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR T.V. MTG. BRKT. ASSY. 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (2 REQ’D.) 7/8" DISH WASHER (2 REQ’D.) 1/4-20 HEX NUT (2 REQ'D.) MONITOR MTG. BRKT. T.V. BEZEL ASSY. TV. BEZEL PLEXI-GLASS (TINTED) BEZEL MTG. BRKT. ASSY. INTERLOCK SWITCH & BRKT. ASSY. U.S.A. 25¢ COIN DOOR ASSY. COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE LARGE PLASTIC CASH BOX 1/4-20 x 1-3/8 BLACK RND. HD. BOLT (4 REQ'D.) 7/8" DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ'D.) GAME LOGIC BOARD ASSY. P.C. SUPPORT BRKT. — 12” LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 2-1/2" LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 6-1/2" LG. #8 x 11/16 UNSLOT. HEX HD. M.S. (13 REQ’D.) #8 FLAT WASHER (13 REQ'D.) PROGRAMMED MS. PAC-MAN BOARD ASSY. AUXILIARY BOARD & BRKT. ASSY. AUXILIARY P.C. BOARD ASSY. P.C. BOARD SUPPORT AUX. P.C. MTG. BRKT. ON-OFF SWITCH & BRKT. ASSY.
ADDITIONAL PARTS LIST
BACK DOOR LOCK ASSY. 5-5/8" SQR. VENT GRILLE (4 REQ'D.) PROTECTIVE BUBBLE — BACK DOOR #8-32 x 3/4 CARRIAGE BOLT (10 REQ’D.) #8-32 HEX NUT W/SEMS (10 REQ'’D.) HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. MASTER CABLE ASSY. LINE CORD ASSY. GROUNDING CLIP GROUND STRAP TRANSFORMER BOARD ASSY. FILTER BOARD ASSV. CREDIT MULTIPLIER BY-PASS P.C. BOARD ASSY.
4-9
NO. 599 — MS. PAC-MAN — COCKTAIL — FRONT
4-10
NO. 599 — MS. PAC-MAN — COCKTAIL — FRONT — PARTS LIST
ORDER BY PART NUMBER ONLY
0017-00009-0499 COVER GLASS — 32” x 22” x 1/4” 0599-00901 -0000 ARTWORK UNDERLAY 0775-00104-00XF GLASS CLIPS (8 REQ'’D.) 0017-00101-0117 #8 x 5/8 PHIL. TRS. HD. SCREW (16 REQ’D.) 0508-00905-0000 T.V. PLEXI-GLASS (SMOKED) — 17-3/8" x 13-1/4" x 1/8” 05038-00901-0000 PLEXI-GLASS CLIPS (4 REQ’D.) 0017-00101-0017 #6 x 1/2 SLT. HEX HD. SCR. (4 REQ'D.) 0557-00900-0000 TV. BEZEL A599-00004-0100 CONTROL SHELF ASSY. — PLAYER #1 A599-00004-0200 CONTROL SHELF ASSY. — PLAYER #2 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS (3 REQ’D.) 0017-00003-0187 6" x 9" SPEAKER 8 OHM, 9W. 0017-00101-0136 #8-32 x 1-1/4 CARRIAGE BOLT (12 REQ'’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (12 REQ’D.) A090-00300-07BK U.S.A. COIN DOOR ASSY. — 25¢ 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) A595-00019-0000 COIN DOOR CABLE ASSY. 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)
4-11
NO. 599 — MS. PAC-MAN — COCKTAIL — INTERIOR ACCESS
NO. 599 — MS. PAC-MAN — COCKTAIL — INTERIOR ACCESS — PARTS LIST ORDER BY PART NUMBER ONLY
0017-00003-0339
A515-00017-01XF A515-00017-02XF 0017-00101-0109 0927-00101-00XF 0017-00101-0598 0610-00132-00ZN 0017-00009-0033 0017-00101-0141 0017-00009-0514 0017-00101-0136 0017-00101-0628 0017-00103-0061 0599-00100-00XF 0599-00900-0100 0599-00900-0200 0017-00101-0620 0017-00103-0061 0017-00101-0341 0510-00101-00XF A595-00005-0000 A599-00006-0100 A599-00006-0200 0017-00032-0051 0930-00104-0000 0017-00101-0025 0930-00904-0000 0017-00031-0044 0017-00003-0219 0017-00101-0555 A082-91375-B000 0624-00902-0100 0624-00902-0300 0017-00101-0141 0017-00104-0031 A932-00026-0000 A595-00020-0000 A084-91415-B617 0017-00042-0106 0595-00107-0000 A084-91375-A595
A599-00008-0000 A088-00013-0000 0017-00003-0187 ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR MONITOR SUPPORT ASSY. — RIGHT MONITOR SUPPORT ASSY. — LEFT #8 x 5/16 UNSLOT. HEX HD. BOLT (6 REQ’D.) SUPPORT ANGLE (2 REQ'D.) #8-32 x 5/16 SLT. HEX HD. M.S. (8 REQ’D.) STRIKE (2 REQ’D.) LATCH CLAMP (2 REQ’D.) — NOT SEEN #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) 2-1/2" HINGE (2 REQ'’D.) #8-32 x 1-1/4 CARRIAGE BOLT (4 REQ’D.) #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) CONTROL PANEL (2 REQ'D.) DECORATIVE OVERLAY — PLAYER #1 DECORATIVE OVERLAY — PLAYER #2 #8-32 x 1/2 CARRIAGE BOLT (8 REQ’D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) #6 x 1/4 PHIL. TRS. HD. SCR. (14 REQ'D.) BOTTOM PAN (2 REQ'D.) CONTROL ASSY. (2 REQ’D.) CONTROL SHELF CABLE ASSY. — PLAYER #1 CONTROL SHELF CABLE ASSY. — PLAYER #2 SMALL RED BUTTON SWITCH W/HARDWARE (2 REQ’D.) CONTROL PANEL LOCATING BRKT. (4 REQ’D.) #8 x 1/2 SLT. HEX HD. M.S. (12 REQ’D.) LIGHT SHIELD (2 REQ’D.) WEDGE BASE LAMP SOCKET (4 REQ’D.) #194 LAMP 14V., .27A. (4 REQ’D.) #6-32 x 5/16 SLT. HEX HD. M.S. (4 REQ’D.) GAME LOGIC BOARD ASSY. P.C. SUPPORT BRKT. — 12” LG. P.C. SUPPORT BRKT. — 2-1/2" LG. (3 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (13 REQ'’D.) #8 WASHER (13 REQ'’D.) FILTER BOARD ASSY. AUXILIARY BOARD & BRKT. ASSY. AUXILIARY P.C. BOARD ASSY. P.C. BOARD SUPPORT AUX. P.C. MTG. BRKT. PROGRAMMED MS. PAC-MAN BOARD ASSY. (ITEMS 17 THRU 19) TRANSFORMER BOARD ASSY. ON-OFF SWITCH & BRKT. ASSY. 6" x 9” SPEAKER 8 OHM, 9W.
NO. 599 — MS. PAC-MAN — COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
A775-00013-0000 FAN ASSY. 0151-00081-0000 4" FAN 0775-00110-00XF FAN PLATE 0749-00106-00XF 0017-00101-0347 0017-00104-0009 0017-00103-0005 0017-00101-0026 VENT SCREEN #6-32 x 1/2 R.H.M.S. (4 REQ'D.) #6 EXT. WASHER (4 REQ'D.) #6-32 HEX NUT (4 REQ’D.) #8 x 5/8 SLT. HEX HD. M.S. (4 REQ’D.)
ADDITIONAL PARTS LIST
CREDIT MULTIPLIER BY-PASS P.C. BOARD ASSY. COIN BOX ASSY. COIN BOX COVER ASSY. COIN BOX SIDE CHANNEL ASSY. — SHORT COIN BOX SIDE CHANNEL — SHORT #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) #8 WASHER (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ'D.) INTERLOCK SWITCH & BRKT. ASSY. TEST SWITCH & BRKT. ASSY. HIGH VOLTAGE SHIELD — FORMED GROUND STRAP MASTER CABLE ASSY. POWER CABLE ASSY. LOW VOLTAGE CABLE ASSY. A.C. ADAPTOR CABLE ASSY. LINE CORD ASSY. HIGH BASE LEG KIT ASSY. — OPTIONAL A082-91109-A000 A927-00019-0000 A962-00004-0000 A962-00005-0000 0962-00101-0000 0017-00101-0628 0017-00104-0022 0017-00103-0061 A088-00014-0000 A866-00036-0000 0927-00907-0000 3000-17246-1200 A599-00012-0000 A599-00009-0000 A599-00010-0000 A599-00011-0000 A866-00049-0000 0927-00005-0000
MS. PAC-MAN — TRANSFORMER BOARD ASSY.
MS. PAC-MAN — TRANSFORMER BOARD ASSY. — PARTS LIST
ORDER BY PART NUMBER ONLY
MT00-00080-0000 MT00-00082-0000 MT00-00084-0000 MTO00-00085-0000 0017-00101-0637 0017-00103-0008 0017-00101-0014 0720-00001-0400 0720-00001-0300 0720-00001-0200 0017-00003-0001 NNOOLONMANA
0017-00003-0004
0017-00003-0169 0017-00003-0261
0866-00906-0000 0017-00003-0114 A031-00002-0000 3000-17246-0900 3000-17246-1000 3000-17246-0300 TRANSFORMER — 115V. — UPRIGHT & MINI TRANSFORMER — 115/115V. — UPRIGHT & MINI TRANSFORMER — 240V., SO HZ — COCKTAIL ONLY TRANSFORMER — 115V., 50 HZ — COCKTAIL ONLY #8-32 x 1" CARRIAGE BOLT (4 REQ'D.) #8-32 HEX NUT (4 REQ’D.) #6 x 1/2 SLT. HEX HD. SCREW (13 REQ'D.) 4 POSITION FUSE CLIP ASSY. 3 POSITION FUSE CLIP ASSY. — COCKTAIL ONLY 2 POSITION FUSE CLIP ASSY. — UPRIGHT & MINI FUSE 1A., 250V. (2 REQ’D. — UPRIGHT & COCKTAIL, 1 REQ'D. — MINI) SLO-BLO FUSE 2A., 250V. (1 REQ’D. — UPRIGHT, 2 REQ'’D. — COCKTAIL, 3 REQ’D. — MINI) FUSE 5A., (2 REQ’D.) SLO-BLO FUSE 1-1/2 A., 250V. (1 REQ'D. — UPRIGHT & COCKTAIL) FUSE SHIELD — NOT SHOWN NOISE FILTER TERMINAL STRIP ASSY. GROUND STRAP — UPRIGHT GROUND STRAP — MINI GROUND STRAP — COCKTAIL
4-15
FRONT DOOR ASSEMBLY — U.S.A. 25¢
FRONT DOOR ASSEMBLY — U.S.A. 25¢ ORDER BY PART NUMBER ONLY | rrem | PART NO. DESCRIPTION 0090-00002-02BK DOUBLE ENTRY COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) A090-00073-02BK DOUBLE ENTRY COIN DOOR W/DRESS PLATE 0017-00101-0123 #8 x 1/4 UNSLOT. HEX HD. SCREW (4 REQ’D.) 0017-00007-0019 KEY HOOK 0017-00101-0552 #6-32 x 1/4 CARRIAGE BOLT (4 REQ'’D.) 0090-00117-03XF COIN ENTRY PLATE — 25¢ (2 REQ’D.) A097-00005-0000 DOOR LOCK & KEY W/SCREW & NUT (OR) A097-00006-0000 DOOR LOCK & KEY W/SCREW & NUT 0090-00128-00XF DOOR TILT SWITCH BRKT. 0017-00005-0041 DOOR CAM A090-00095-0000 DOOR TILT SWITCH 0090-00126-01 XF SWITCH BACK-UP PLATE 0017-00101-0525 #5-40 x 9/16" PHIL. HD. M.S. (2 REQ’D.) A090-00096-0000 DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 0090-00903-9500 25¢ WINDOW (2 REQ'D.) 0090-00143-00XF COIN PLEX RETAINER 0017-00003-0219 12 VOLT LAMP — GE. #1895 (2 REQ’D.) 0017-00031-0048 BAYONET SOCKET W/BRKT. (2 REQ’D.) 0017-00104-0002 #6 SPLIT LOCK WASHER (8 REQ’D.) 0017-00103-0084 #6-32 HEX NUT W/SEMS (4 REQ’D.) A090-00057-0000 COIN METER 0017-00101-0124 #6 x 1/4 UNSLOT. HEX HD. SCR. (8 REQ’D.) 0017-00032-0051 PUSH BUTTON SWITCH 0017-00032-0007 SLIDE SWITCH 0017-00072-0034 STEEL OVAL HD. RIVET 0090-00173-0000 COIN COUNTER MTG. BRKT. A090-00082-0000 TEST SWITCH & BRKT. ASSY. (ITEMS 23 THRU 25) A090-00087-0000 COIN CHUTE & TOP ASSY. (2 REQ’D.) 0010-00134-0000 SPRING 0010-00181-0000 SPRING 0017-00007-0083 1/8 x 1-5/8 ROLL PIN 0090-00129-00XF PIVOT POST 0090-00167-00XF PIVOT LEVER 0093-00155-00XF REJECT LEVER 0017-00100-0018 E-RING A090-00088-0000 REJECT LEVER ASSY. (2 REQ’D.) (ITEMS 30 THRU 33) A090-00085-0000 COIN ACCEPTOR FRAME ASSY. (2 REQ’D.) 0017-00005-0003 COIN ACCEPTOR W/STRING CUTTER (2 REQ'D.) (OR) 0017-00005-0211 COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ’D.) (OR) 0017-00005-0214 COIN ACCEPTOR W/STRING CUTTER (2 REQ'D.) A090-00064-0000 ANTI-PENNY DEVICE 0017-00101-0099 #6 x 1/4 SLT. HEX HD. M.S. (2 REQ'D.) 0090-00162-00XF COIN SWITCH MTG. BRKT. 0017-00005-0203 COIN SWITCH CHUTE 0017-00005-0195 COIN SWITCH 0010-00599-0000 COIN SWITCH WIRE 0017-00007-0132 PUSH-ON RING A090-00059-0400 COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) 0017-00101-0698 #4-40 x 3/4 SLT. RND. HD. MS. (2 REQ’D.) A090-00077-0000 COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43) OCWMNANAWONA
MS. PAC-MAN — CONTROL ASSEMBLY — ALL VERSIONS
4-18
MS. PAC-MAN — CONTROL ASSEMBLY — ALL VERSIONS — PARTS LIST
ORDER BY PART NUMBER ONLY
A932-00022-0000 BALL & SHAFT ASSEMBLY 0017-00100-0025 1/4 E-RING 0921-00702-0000 STOP SPACER 0921-00902-0000 SLIDE PLATE PIVOT PLATE WELD ASSEMBLY #8-32 x 1" CARRIAGE BOLT (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) A595-00006-0000 0017-00101-0637 0017-00103-0061 0932-00902-0000 GROMMET 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. MS. (10 REQ'’D.) 0962-00904-0000 SLEEVE 0017-00101-0527 0020-00202-0000 A932-00009-0000 A932-00012-00XF 0932-00905-0000 0921-00700-0000 #5-40 x 5/8 SLT. RND. HD. SCR. (8 REQ’D.) SWITCH PLATE (4 REQ’D.) SWITCH ASSEMBLY (4 REQ’D) STOP PLATE & SWITCH BRKT. ASSY. WEAR PLATE ACTUATOR
V Technical Troubleshooting
Harness Component Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.
General Suggestions
The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.
If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.
Transformer and Line Voltage Problems
Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.
5-2 If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.
HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.
A Glossary of Microprocessor Terms
MICROPROCESSOR — one or several microcircuits that perform the function of a computer’s CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.
CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips.
PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.
EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.
ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM'’s contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).
Introduction to the
Z-80 CPU
The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed" controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LS! technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:
- -The Z-80 is fully software compatible with the popular 8080A CPU.
- Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
- CPU (Central Processing Unit)
- Memory
- Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose |/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)
Subtract Increment
Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.
Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described. = ~~]
| ™, | ZL | | 3 | a, |
[> A,
| MREQ | ui | = | |
| SYSTEM | ira | 20 | | 33 a, |
CONTROL “, 5 2 34 ~— [te
| we | 2 | a |
36 Me
| AFH | aq 28_] | 7 a, |
BA ADDRESS
| iar | = 8 | Z-80 CPU | [> A, |
a
| a | wat | —%4 9! | — An |
CONTROL i, Av
| int | =«—_8_ gf | Ass |
| Nw | az | | 4 » a, |
ea
| RESET | 26 | y |
CPU BUSRQ BUS ee Busak «| CONTROL |
® my W “sv DATA GND 2 BUS
Z-80 PIN CONFIGURATION
Ag-Ais (Address Bus) Tri-state output, active high. Ap-A,5 constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data ex+ changes and for I/O device data exchanges. !/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ay is the least significant address. bit. During refresh time, the lower 7 bits contain a valid refresh address.
D,-D, (Data Bus) Tri-state input/output, active high. Dp-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.
My, (Machine Cycle one) __ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1oRQ (Input/Output Request) Tri-state output, active low. The iORQ signal indicates that the lower half of the address bus holds a valid I/O address for a I/O read or write operation. An TORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.
5-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.
HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.
INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00664. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WATT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:
- Disable the interrupt enable flip-flop
- Set Register | = 00H
- Set Register R =00n
- Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.
BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated.
BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.
CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements. a
PLEASE NOTE:
THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.
IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.
OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!
THANK YOU
VI T.V. Monitor
Color T.V.
Color T.V Monitor
Introduction: (How to
use this section of your manual.)
This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn't necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!
If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.
If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings
6-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:
- Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
- Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
- Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.
That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)
Symptom Diagnosis
. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). e Bad yoke. ® Bad vertical output section. Open fusible resistor in vertical section. « Bad height control. © Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). e Bad yoke. @ Open width coil. e Open part in horizontal output section. . Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal.
. Colors missing; check: Interface color transistors. Color output transistors. Cracked printed circuit board. Color circuits. . Video input jack. . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. moOm>
. Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. . Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).
6-2 10.
1.
12,
13.
14,
15.
16.
17.
18.
19.
20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.
Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal syne needs adjusting. B. Magnetic or electromagnetic interference.
Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.
No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).
No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.
No high voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moOOmP
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.
|. Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.
B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.
24, Can't adjust purity or convergence:
A. Use a degausser to demagnetize the picture tube carefully following your degausser's instructions. Picture tube defective. Metal foreign material is in picture tube shield. D. Nearby equipment is electromagnetically interferring. E. The poles of the earth are pulling off the purity. F. Poor focus or width of picture. op
Guide To Schematic Symbols
THERMISTOR (POLARITY DOESN’T MATTER)
SNYYYW
INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
(+) ANODE
ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
FUSE (POLARITY DOESN'T MATTER)
CATHODE (-)
ANODE (+)
DIODE
COLLECTOR ava COLLECTOR a BASE ————> BASE———> EMITTER ane EMITTER iS
NPN TRANSISTOR PNP TRANSISTOR
MW
VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN’T MATTER) (POLARITY DOESN’T MATTER)
i
LINES ARE CONNECTED ELECTROLYTIC CAPACITOR
L
LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)
tha + GROUND
6-4
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:
- Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
6-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.
To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.
Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board.
Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the onmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and a short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. Itis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or none atall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.
THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
An interesting aside is that our sync is composite negative sync. That means two things:
- The sync is a negative going wave form.
- There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz).
The sync is amplified by a sync amplifier transistor and sent 0 its way to the oscillators. The sync or timing information wii! be explained along with the oscillator shortiy. The color informatior: is sent via wires to the neck board where the mair: amplification occurs. This will also be discussed later.
VERTICAL AND HORIZONTAL DEFLECTION — After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assmebled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” or 19” color monitor uses transistors for its sync section. An Electrohome 13” or 19" color monitor uses an integrated circuit |C501 for its sync section. The idea is all the same. The output to the vertical amplifying transistors for all monitors must be a sawtooth wave form, sort of likea bunch of pyramids, racing to the yoke’s vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set. The amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.
6-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Again, Wells Gardner uses transistors for the horizontal oscillator, and Electrohome uses the other side of IC501. Still, the effect is the same. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in a car and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillators frequencies must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.
THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.
COLOR CIRCUITS The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There only two, one for the red and one for the green. The
blue doesn’t have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount ot amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don't show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.
PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check the ernitter on TR502 of the Wells Gardner monitors, or the emitter of X04 for the Electrohome monitor. Here are the voltages you should receive: Wells Gardner = 127VDC Electrohome = 120VDC
The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, the GO7-FBO or G07-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.
THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuits work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.
Differences Between Monitors
The easiest way to identify the brand of monitor you are working with, assuming you can't find the brand name written on it anywhere, is to see if there are two circuit boards rising up from the chassis toward the picture tube neck. In other words, they stand up, or are perpendicular to the chassis, with a black plastic bracket holding them in place. This is a description of a Wells Gardner monitor. They use separate boards for main chunks of circuitry. Therefore, you have a “power board” (the power supply), an “interface board” (the interface section), and a “horizontal/ vertical board” (for the deflection circuitry). Still, there are a few parts on the chassis, but most can be found on the board. An Electrohome monitor has no separate boards, except for the neck board, and just has a flat chassis.
Another good way to determine which monitor you have is to check the transistor call out numbers that are printed on the chassis next to the part. For instance, on the neck board, one of the color output transistors is TR401. If you look through the schematics or the parts lists, you will find TR401 in the Wells Gardner literature. On the other hand, the neck board transistor may say X101. X101 can be found in the Electrohome literature. So, all Wells Gardner transistor call outs begin with TR, and Electrohome transistor call outs start with an “X”.
Monitor schematics and parts lists omitted
VII Schematics and Wiring Diagrams
ov. MT-02 XFORMER 3 Ame BIMETER 4 CREDIT MULTIPLIFR PC, CON SW. =~ fo —_
arc : ig ee Btw vert ——_.-* won Mey
MOVE DOWN
UP brew rc
- en Move
0 COM DOOR &
CONTROL PANEL &
MONITOR CHASIS.
7A | MONITOR INTERFACE ‘6 POS MS, PAC-MAN U.R. MOWMY MEG. CO. 10750 W. GRANO AYE. FRANKLIN PARK ILL. 6013!
WIRING SCHEMATIC PART NO. MO5!- 00595-A004
!
GAME LOGIC BOARD
R.C.A082-91375-A000
- 1) T wonton WACK
| MONITOR INTERFACE 1 © POS s.u |-Gray ‘ sv. BEE Zana —. a w-82 FORMER -—————
MS. PAC-MAN U.R. ' MOWEY MEG. CO. : 10750 W. GRAND AVE. 1 FRANKLIN PARK ILL. 6013!
WIRING SCHEMATIC PART NO. MOSI- 00596-ACOS
Lora MT-80
I C4) 2 AMP , SLO-BLO
ill xey |b re wey le 1F
GAME LOGIC BOARD
PC.A082-91375-A000 -B00O 44 Pos
YO COW DOOR &
CONTROL PANEL & C
MONITOR CHASIS
7-2
en) i MONITOR 7s Tac MT-82 XFORMER, ame (FUSE _220¥.
MS PAC -MAN MINI 1 MIDWAY MEG. CO,
10750 W. GRAND AVE. FRANKLIN PARK ILL. 60/3/ PRE LSIALALELIG
WIRING SCHEMATIC PART NO. MO5!-00602-A004
{ is S Ps. iszsaras fen FALTER eet ‘MT-80 #1METER+ CREDIT MULTIPLIFR PC. CON SW 7 ~#2 METER
COIN SW,
GAME LOGIC BOARD
PC. A082 -91375-A000 |
MOVE
DOWN sype
OFF " 70 COIM DOOR &
CONTROL PANEL &
MONITOR CHASIS
‘wonton INTERFACE ‘6 POS MS PAC-MAN Resin Bare Wane Dow e ‘afuler | Vi Capotesse SS SA Le |
fetetl MOMITOR ace
| MONITOR INTERFACE 1 6POS MS PAC-MAN MINI. MiONMY MFC. CO. 10750 W. GRANO AYE FRANKLIN PARI ILL. 6013!
WIRING SCHEMATIC PART NO. MO5!-00602-A0OS
yrure a et ee MS PAC MAD MT- £0 4 SSS AUX. BD.
1 SSS wea BLu-y ‘ SSS AMP FUSE | | SSS SLO-BLO 1 H SSS
: | wey ‘od | rey wey 'e | CREDIT BYPASS PC. \ 1 #1 COIN SW, o> x - i
'
- : GAME LOGIC BOARD
: ' PC, A082 -91375-A000 ' -B000 10 COM DOOR & CONTROL PANEL & MONITOR CHASIS

This page is a drawing, shown as the original scan.
eek MT- gS XFORMER 3 ame
Fuse
Cvlo ae, a nro M120 x6 MIO Fe
i Rec UP, —4_BRN-¥ 112 #2 Ri eo R= BLU 3 #2 T, eo 0-6 IP Li#t#2 DOWN, —~,_ W-Y 'v —
CREDIT BYPASS PC,
#1 COIN SW.
ant Aa
i MOMITOR ea 1, MON
MONITOR INTERFACE
1 @ Pos
MS. PAC. MAN CT
MIDWAY MFC. CO. 10750 W. GRAND AVE. FRANKLIN PARK ILL. 60/31
WIRING SCHEMATIC PART NO. MO5!- 00599-A003
MS PAC-MAN AUX. BD. GAME LOGIC BOARD PC. A062 -91375- A000
-BO0O
ood
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ISSYE Vial mame y
Teme sme
ave
Te] creew
oP MERSIN, SOR Cecuray a ee 2 7-9
Ut, U2, U3774L S257 U4,U5,U6774LS167 U7,U8,U9,-74L S86 UIO —74LS02 «| MF 50v — (6) AX CER K4w — (2)- 14-POS. KK-100
#% MOUNTED ON
SOLDER SIDE
ee ee Lesions use onPAC- MAN MIDWAY MFG. CO.
—a V-RAM ADDRESSER (284) DO NOT SCALE DWG.
A082_91 384.8000
pate 10-27-80 COMPONENENT - LAY- OUT
Pp us bs] ai bhe 1B nN 12zevP
us
us 2 Je e _32vP
- 64V fz]
[nu] - 32v
u7 ) ee) 6 32HP U7 Jee v 1eHP ve
= 28 PIN CONNECTOR
= PULL UP
= [4] 16H
[5] 32H
(e] 64H MIDWAY MFG. CO FRANKLIN PARK ILL
[oan wm [exo DATE NOv 2S. eQNO.REQOD 1 USED ON PAC-MAN
PARTNO: AO82-91384-BOOO SCHEMATIC PARTNO. MOS1 00932 8032
7-11
U9D-74LS139 Ul -74LS02 U2 -74L$74 U3 -74LS02 U4 -74LS74 US -74L$244 U6-74LS374 U7-74LS374
- MF 50v AX, CER, ()- Kw RESIS,
- MOUNTED ON
SOLDER SIDE
MO5I -00982 -B 03!
MIDWAY MFG. CO. ants NO.REQ'D |_ PER FRANKLIN PK. ILL. DIM. TOLERANCES MATL. P~— _| NO; uneess sree? —_ Z-8C SYNC BUSS CONTROLER(285) ys aoe 2- 91383 -8000 i TOE P—— | coMPONENT LAYOUT
feo] 07
22| 06 13|8 y39 3 [2 E 2
os
25] 04
24] 03
- >
fe} >
fis} ow ° so7 [9
i u Boe [7 ? r ~ i)
\ 4 60S {é}
16 soa [4]
\
s 803 [5
' i : soz [a]
Bol fh
80% fio!
Cc fop) moOoCoC Oooo Ww nN £ erpeprnerpen x ° m al
NOTES!
0 = 28 PIN CONNECTOR
= PULL UP
MIDWAY MFG,CO FRANKLIN PARK ’ . He
DATE. NOv-21-80|NOREGD 1
DESC. 780 SYNC BUS CONTROLER (285]| PART NO- AQRB?- 91 SCHEMATIC PART NO. MOS1- 00932-8030
7213)
DESIGNATION LIST
DESIGNATION DESCRIPTION c1,c2 IOMF ELEC. CAP. c3-c6 IMF CER.CAP Icue c6620 "ul ce 62! “u2 cee22 "U3 cee23 "U4 Z-80A "US EPROM 2716 " U6,U7 EPROM 2532 ICSUB-ICSUS 20 PIN IC SOCKET
| “ua | 40PIN" | " |
| " US-ICSU7 | 2qpN" | " |
| “al | 40PIN" | “ |
Jt CABLE ASS'Y. 40-PIN PCB MS, PAC-MAN AUX . P.C.BOARD
TA4 PROJECT ENG
DIM. TOLERANCES UNLESS OTHERWISE SPEC CONCENTRICITY Ti R 002 FRACTIONAL +164 DECIMAL + 005 HOLE DIA + 002. 000 1S CONFIDENTIAL & PROPERTY OF MIDWAY MFG CO. FRANKLIN PK., IL. 60131 ABALLY CO. a J. SZERSZEN
MIDWAY MFG. CO.
ASSEMBLY DRAWING MS, PAC-MAN AUX P.C. ANGLE 212° DO NOT SCALE OWG A084 - 91415- BGIT MIOWAY MFG. CO. 1981 ALL RIGHTS RESERVED
c1
- C4
U4
*{_ 4 c2
A084-91415-B617 CRO REFE
DESCRIPTION. .IMF AX.CER.CAP
IOMF AX. ELEC. cee20 C682 ces22 ces23
Z-80A
EPROM2532
"2716
20 PIN IC SOCKET 24PIN" " 40PIN" "
CABLE ASS'Y 40-PIN
MS. PAC-MAN AUX. P.C. BOARD
IPART NO. 0-5-1 -0:06:1:7 -B 001 Li:
QUAN. DESIGNATION 4 C3-C6
2 Ccl,c2 [ Ue I ul i} v2 t U3 I U4
t u6 i U7 ! US
4 ICSUD-ICSU3 3 ICSUS-ICSU7 2 Iesu4, Icsul
! ul PART_NO. 0508-00800-0800
0508-00800-1100 0066-O14CX-XXQX 0066-01SCX-XXQX 0066-OIGCX -XXQX 0066 -O17CX-XXQX 0932-00807-0000
0595 -00803-0200 058 -00803 -0300 0895-00803-0100
0508-00804-0/ 00 0508-00804-0500 0508- 00804-1800
0895 -00804-0200
A080-SI415- BEIT
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
# 100 PF 5 9 i wa (Torn. <4
TEKA CONN, TP3-22]-L04B90 w/ BRACKET
MO51-00932-D037 LL REVISIONS
- pen ov _pac may | MIDWAY MFG. CO. DIM. TOLERANCES ae PART|NO : — pec-Mey EAL ° ae PAC-MRN Filter P.C cont loare oR -HI-B 1 |
UNLESS SPECIFIED DIM TOLERANCES MO5|-00932-0038 DO NOT SCALE DWG U5ED ON
NO REQD
SCHEMATIC DIAGRAM PAC-MAN FILTER PC. PER PAC-MAN MIDWAY MFG. CO. me
A082-91389-D000
TAT x 7V AC 4X10 MH(WW)
7V CT. [Tip ee TT 2X 10 MH(WW) moat t- aw
2X .O1 MF = 2 8 = x
f X21 MF 10 MH 2 X.01MF oo <b I
5X .01 MF
COMMON
P2 START
I 5X .01 MF <M
P2_ RIGHT
P2 LEFT
P2-DOWN - COIN!
CREDIT
SERVICE a
SPKR f 4X .01l MF 6 X 10 MH I 3X .Ol MF
pone ney xe JW 10 BOLTED STRAPS TO GND. dd OLD
oper of § JR Stir Ni vibe » U [ee D) Cl Tae
C=] oa ami) (amas) ANWL AGE INL xT Cones can ) mses) astm) (way ] [waz]
lel
LT St Soe SR AR: HY} SCHOTIKY DIODE — INS8I8 OR INSBI7 MO5!-00932-A027 MIDWAY MFG. CO. OIM TOLERANCES a PART NO, A082-91348-C:000
+
- LMF 50V CER. AX. 10 MF 35V
IMF 35V TANTS 5
SCHOTIKY DIODE 2X INS8I8 Py OR INSBIT: 6-2
4.7 MF 35V
MOSI-00932-A029 [revisions MIDWAY MFG. CO.
DIM TOLERANCES Go 7 sages nals ———| SHEMET Ova A082 -91348 - co0o pried l - 7 cant" tedlonn- 10/93/80 ee CREDIT MULTIPLIER