CATHODE RAY TOMES

Missile Command TM-147 2nd Printing

Missile Command (rev 3, A035467-02/04 PCBs) (Atari, 1980) · Technical Manual · 52 pages · 52 sections · original scan

Page 1

Operation, Maintenance

and Service Manual Complete with Illustrated Parts Lists GNetwwUUeD

Page 2

GAME SERIAL NUMBER LOCATION Oo

Your game’s serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the TV monitor, Regulator/Audio II PCB, and game PCB. Please mention this number whenever calling your distributor for service.

GAME SERIAL # IDENTIFICATION TAG

TV MONITOR

GAME PCB

Page 3

| JS ILS COMMA

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists ™

Published by: f ATARI INC 1265 Borregas Avenue eee, P.O. Box 427 Sunnyvale, California 94086

Copyright © 1980 by Atari, Inc. All righ

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. \ n) its reserved.,

Lithographedin the U.S.A. 7d © A Warner Communications Company

Page 4

Missile Comman aT!

Table of Contents

Location Setup

Game Inspection 3 Game Installation . 3

  • Voltage Selection ... 6... 62 eee eee eee 3
  • Interlock and Power On/Off Switches . .. 3 Self-Test Procedure..........-.-45 .. 6 Game Play ........ 0. cc eee eee eee eee e etn eee 9
  • Attract Mode 9
  • Ready-to-Play Mode . 9
  • PlayMode......... . 9
  • High Score Initial Mode ...... 2.0.0 cece cece eect e eee eee 9

Maintenance and Repair A. B.

mmo Cleaning... 0... cece eee nent ett e eee Fuse Replacement... . Opening the Control Panel .

  • LED Switch Replacement... .
  • Trak Ball™ Maintenance and Repair ............ 00... c eevee ee 13 TV Monitor Replacement........... +. 14 Printed Circuit Board Replacement . 7 Opening the Attraction Panel ... .
  • Replacing Speakers ........
  • Replacing Fluorescent Tube . Coin Door Repairs . . Game Operation. ...

\llustrated Parts Lists

Page 5

List of Illustrations

Figure1 OverviewofGame .......0.... 0.00. Figure 2 Installation Requirements . Figure 3 Power Supply weer 4 Figure 4 —_ Interlock and Power On/Off Switches ........... wees 5 Figure 5 —_ Location of Self-Test Switch, Volume Control and Option Switche: 6

Figure 6 Self-Test Procedure . . 7 Figure 7 Option Switch Settings . . 8 Figure 8 Opening the Control Panel ... 12 Figure 9 Trak Ball™ Maintenance and Repair - 13 Figure 10 TV Monitor Removal. . 14

Figure 11 Game and Regulator/Audio ll PCB Replacement ................. 15 Figure 12 Opening the Attraction Panel ............... . 16 Figure 13 Removing and Reinstalling a Coin Mechanism . 17 Figure 14 Switch and Trip Wire Replacement... . . 18 Figure 15 Coin DoorLamp Replacement...............00ce eee ee eee eeee 19

Figure 16 Power Distribution . . - 20 Figure 17 Signal Distribution .. . .21 Figure 18 Cabinet-Mounted Assemblies ............ . 24 Figure 19 Attraction Panel and Fluorescent Light Assemblies . . 26 Figure 20 Control PanelAssembly ............ 000: eee eee eee eee 27

Figure 21 Trak Ball™ Assembly ......0. 000.000 cece eee eee 28 Figure 22 Steering Printed Circuit Board Assembly . . 30 Figure 23 Type B Power Supply Assembly . . 31 Figure 24 NewCoinDoor............ . 32 Figure 25 Game PCBAssembly........ . 36 Figure 26 Regulator/Audio Il PCB Assembly... ....... 0.0.0 cee en eee eee ee 40

Page 6
NOTE

If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.

WEST and CENTRAL U.S.A.

Parts for all Atari Customers. Sales and Service

Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103

(Monday - Friday, 7:30 - 4:00 pm Pacific Time)

From California, Alaska or Hawaii “© (408) 745-2900

a From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A.

Sales and Service Only

Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347

(Monday - Friday, 8:30 - 5:00 pm Eastern time)

From New Jersey = (201) 469-5993

From anywhere else in this area toll-free (800) 526-3849

Page 7

Location Setup

A. New Parts

The Missile Command™ game has four new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: @ Color TV Monitor. Made especially to Atari specifications, the 19-inch monitor has been color-converged at the factory. All convergence adjustments are cemented and locked in place, to prevent accidental changes. This helps provide higher reliability for the service technician. @ Isolation Transformer. The color TV monitor chassis in this game does not contain an isolation transformer. Atari has mounted an isolation transformer on the floor of the cabinet to protect operators. If you service this color TV on a test bench, you must isolate the line voltage! (See instructions on pages 14-15.)

Page 8

%

ATTRACTION PANEL COLOR TV MONITOR

TV MONITOR SHIELD ~

REGULATOR! AUDIO II PCB

CONTROL PANEL

GAME PCB

TRAK BALL™ CONTROL

POWER SUPPLY

POWER ON/OFF SWITCH

COIN DOOR

Figure 1 Overview of Game

Page 9

@ Regulator/Audio Il PCB. This slightly redesigned printed-circuit board has two additional voltage regulators for games using 2708 EPROM memory chips. The board’s new + 12V and —5V regulators are both mounted on the heat sink. Otherwise this board is the same as past Regulator/Audio PCBs. @ New Coin Door. This door will accomodate two or three mechanisms, and up to four coin counters. Its triple-arm locking bar provides added security. For greater ease of access, the self-test switch is now mounted on the door, rather than inside the cabinet.

These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is

mentioned, you will see this symbol: i *-.))

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

[eran NOTE wnt | Do not plug the game in yet!

  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the TV monitor with your hands or metal ob- Jects held in your hands! @ Note the location of the game’s serial number—it is on the metallic label on the back of the game cabinet. Verify that the serial numbers also stamped on the game PCB, Regulator/Audio Il PCB and TV monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and TV monitor for secure mounting.

C. Game Installation

Figure 2 Installation Requirements

Power 150 watts Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 64 x 83 cm (25% x 32% in.) Game Height 186 cm (73% in.)

  • Voltage Selection

Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your \ocation’s line voltage. Check the wire color on the plug and see if it is correct per the list below.

Line Voltage Range Voltage Selection Plug Color

86-104 VAC (95) Black 100-125 VAC (110) Orange 190-220 VAC (205) Green 210-240 VAC (220) Red

  • Interlock and Power On/Off Switches

To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door or panel is opened.

Check for proper operation of the interlock switches by performing the following steps: @ Unlock and open the access panel and the coin door. @ Plug the AC line power cord into an AC outlet.

Page 10

Line Voltage Range Voltage Selection Plug Color 86-104 VAC (95) Black 100-125 VAC (110) Orange 190-220 VAC (205) Green 210-240 VAC (220) Red

VOLTAGE POWER eu, SELECTION \ PLUGS

Figure 3 Power Supply

@ Close the access panel and coin door. @ Set the power on/off switch to the on position. Within approximately 30 seconds the TV monitor should display a picture. @ Slowly open the rear access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door. @ = If the results of the previous step are satisfactory, the interlock switches are operating properly. If the TV monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the on position.

Page 11

POWER ON/OFF SWITCH

SWITCH

SAFETY INTERLOCK SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 12

‘VOLUME CONTROL VOLUME DECREASE: TURN CLOCKWISE

‘SELF-TEST SWITCH

OPTION SWITCHES

Figure 5 Location of Self-Test Switch,

Volume Control and Option Switches

D. Self-Test Procedure

This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the TV monitor and the game speaker; no additional equipment is necessary.

Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options.

To run the self-test, follow the instructions outlined in Figure 6.

Page 13

Instruction Figure 6 Self-Test Procedure

Result if Test Passes Result if Test Fails

  • Set self-test switch to on position (see Figure 5). Note: entering self-test will set the HIGH SCORE TODAY display to 7500.
  • Roll the Trak Ball control in all directions.
  • Press the following switches: ®@ Coin switch trip wires Coin door slam switch @ All three fire switches @ Player start buttons
  • Set self-test switch to off position. After about 5 seconds of frozen attract mode, a low raspy tone is followed by a low beep, then high beep. TV monitor screen displays picture as shown below: ROM OK MAP OK RAM OK + ..plus the options display—see Figure 7 for explanation. Both LED start buttons will also be lighted.

The + moves around on the screen in directions corresponding to Trak Ball control—up to an invisible border along the screen’s edges.

A sound is heard as each switch is pressed. The background color also changes. A continuous raspy tone means V BLANK is malfunctioning. Self-test will not continue. A RAM failure is indicated by a blank or “garbage”-filled screen and a repeated series of 8 beeps, separated by a low raspy tone. See note 1 below. Self-test will not restart. ROM failure is indicated by BAD ROM; see note 2 below. BAD MAP means bit-mapping hardware has failed. BAD CHIP means custom audio I/O chip at location P8/9 has failed.

The + doesn't move in same direction as ball, or not at all. One of the Steering PCBs on Trak Ball control may be bad, harness wires or connector may be loose, Trak Ball reading circuitry on Game PCB may be bad, or Trak Ball bearings may need oiling.

No sound or color changes are produced when pressing one of these switches: indicates a bad switch, loose harness wires, or loose connector.

Note 1:

High beep in Bad chip series of 8 tones: at location: (st P4 2nd N4 3rd M4 4th L4 Sth K4 6th J4 7th H4 8th F4 In test no. 1, a low beep means a good chip; a high beep is a bad RAM, as follows:

Note 2: BAD ROM plus some or all of the digits 1 thru 6 are displayed. These numbers show which 2K of memory are bad. For example, 1 means the first 2K are bad. The + may not appear.
Page 14

Figure 7 Option Switch Settings

To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the game PCB is mounted in place. When changing the options, verify proper results on the TV monitor display by performing the self-test. Note that changing an option on any toggle will cause an immediate change on the TV monitor screen during the self-test.

Toggle Settings of 8-Toggle Switch on Game PCB (at R10) 7 6

854321Option
OnOn4 coin* for 1 play
OffOnFree play
OnOff2 coins* for 1 play$
OffOff1 coin* for 2 plays
OnOnRight coinmech x 1$
3OnOffRight coin mech x 4
8OffOnRight coin mech x 5
OffOffRight coin mech x 6
3OnCenter Coin Mech x 1$ (Center mech is a left
zOffCenter Coin Mech x 2mech in a 2-mech door)
OnOnEnglish language
OnOffFrench language
OffOnGerman language

Off Off Spanish language

Toggle Settings of 8-Toggle Switch on Game PCB (at R8)

87654321Option
OffOffGame starts with 7 cities
OnOnGame starts with 6 cities$
OffOnGame starts with 5 cities
OnOffGame starts with 4 cities

On No bonus credit Off 1 bonus credit for 4 successive coins $

3OnLarge Trak Ball input$
>OffMini-Trak Ball input(Switch must be on for proper

operation of large Missile Command game)

8OffOffOnBonus city every 8,000 points
2OnOnOnBonus city every 10,000 points$
OnOnOffBonus city every 12,000 points
OnOffOnBonus city every 14,000 points
OnOffOffBonus city every 15,000 points
OffOnOnBonus city every 18,000 points
OffOnOffBonus city every 20,000 points
OffOffOffNo bonus city

The format of the self-test display is as follows: An example of an actual option switch display is as follows:

Bonus city every _____ points (line disappears it no bonus city is BONUS CITY EVERY 10,000 POINTS chosen) + Coinage setting 4, 5, 6, or 7 cities (always in English) A B c D

A is the center mech multiplier for 3-mech doors, left mech multipiier if a 2-mech door. This number is either 1 or 2. Bis the right coin mech multiplier and is 1, 4, 5, or 6. Cis an “F” if switch 4 (of R8) is off. Dis an “X” if switch 3 (of R8) is off. + 2 COINS 4 PLAY 6 CITIES 1 1 x

  • Note: In the U.S., a “coin” is defined as 25¢. If your game also has a $1 mechanism, you must set the right coin mechanism multiplier as per your choice. $ Manufacturer's suggested settings
Page 15

E. Game Play

Missile Command™ is a 1- or 2-player game with a color monitor. The game depicts an Armageddonstyle war in which players defend their bases and cities with antiballistic missiles (ABMs). The enemy—the game computer—launches incoming waves of attack missiles. These weapons may be either individual or branching attack missiles. In addition, the enemy occasionally launches missiles from a fast-moving “killer” satellite or from bombers. The enemy also launches “smart” missiles that usually avoid explosions.

Players receive varying numbers of points for intercepting attack missiles, for having unused missiles still in their bases’ arsenals, and for having their cities undamaged after a missile wave.

The game has five possible modes of operation: attract, ready-to-play, play, high-score initial, and self-test. The latter is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled, and the “HIGH SCORE TODAY” is reset to 7500. A list of eight “highest” scores and initials are also reset onto the screen (to provide player challenge).

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high-score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted, or when entering self-test.

In this mode, the Missile Command name is displayed, then the computer plays one wave—handling both offense and defense. Following this, the computer displays the high score table, then the Missile Command graphics reappear.

  • Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a one- or two-player game. It ends when the 1 PLAYER START or 2 PLAYER START pushbutton is pressed.

When this mode begins, the message PRESS START scrolls along the bottom of the screen. DE- FEND CITIES and red arrows pointing down to each city also appear on the screen. The displayed pictures are otherwise the same as those shown in the attract mode.

  • Play Mode The play mode begins when either start pushbutton is pressed. The mode ends when the player's last city is destroyed.

The three bases—Alpha, Delta and Omega—each have 10 ABMs ready to be fired (shown as A's). Players must be careful to fire the missiles more or less evenly from among those bases, because no more missiles are granted until the screen resets in preparation for a new wave of attack missiles. If the enemy missiles strike a city or base, the colorful buildings or base will change to the solid color of the landscape. The game continues until all cities are destroyed. Missile Command™ has no operator-selectable fixed time length. Thus a highly skilled player can play longer than the novice.

During the second wave, a “killer” satellite and/or bomber will appear on the screen, moving quickly and launching attack missiles at the bases and cities. Players get bonus points for shooting down the satellites or bombers.

The general approach for getting high point scores is fairly quickly discovered: try to launch your ABMs when the enemy missiles have just appeared at the top of the screen. Then they are clustered together, where one ABM can usually destroy several enemy missiles. In the later more advanced waves, players can lay out a blanket of explosions.

  • High Score Initial Mode lf a player's score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. Spinning the Trak Ball control changes the letters (A thru Z and a blank are available). Pressing any fire switch will fix that letter on the screen, and move the choice to the next letter. If the player doesn’t enter his or her initials within 90 seconds, three blank spaces will be entered automatically.
Page 16

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 17

Maintenance and Repair

The Missile Command™ game requires certain maintenance to keep it in good working order. Clean, properly maintained games attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if the Trak Ball™ control or light-emitting-diode switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of eo the game and the coin mechanisms. In addition, you will need to regularly lubricate the Trak Ball control: for details see this chapter.

Page 18

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.

B. Fuse Replacement

This game contains six fuses—all on or near the power supply assembly (not including the TV montor fuses). Replace fuses only with the same type as listed in Chapter 3 of this manual: the single fuse mounted on the floor of the cabinet and the five fuses on the power supply are all described in Figure 23. See the color TV monitor manual, TM-148, for the monitor fuse data.

TRAK BALL CONTROL

L.E.0 SWITCH: TO REMOVE TURN COUNTERCLOCKWISE

NORMALLY CLOSED (N.C.) CONTACT

NORMALLY OPEN (N.O ) CONTACT

LIGHT-EMITTING JS \.

DIODE (L.E.D.)

CONTACTS COMMON CONTACT

C. Opening the Control Panel

Prior to repairing or replacing any switch or the Trak Ball™ on the control panel, or prior to removing the TV monitor, unplug the game. Then open the coin door.

Reach through the opening and remove both sets of carriage bolts and lock nuts, located on the underside of the control panel (see Figure 8).

Lift up on the control panel and tilt it towards you. Be sure that the acrylic TV monitor shield does not fall on you. The top edge of the control panel acts as aretainer strip for the shield: once the control panel is opened, the shield is free and could slide out by its own weight.

Figure 8 Opening the Control Panel

Page 19

Disassemble in the order indicated. (Circled numbers match the steps

Bat Replacement

a nae, PCB Replacement described below.)

Remove the entire Trak Ball assembly as previously described. Locate the three countersunk machine screws in the acrylic top plate; remove these scews. (When the assembly is installed, these three screws are right underneath the control panel.) Remove and replace the ball.

Steering PCB

Remove the hardware holding down the black y

toothed wheel (the right hub); lift this wheel S

off of the black roller shaft. Unplug the con- Tee Ball™ Lubrication Open control panel as illustrated in Figure 8.

nector on steering PCB. Remove the two cross-recessed*Unplug the control panel harness connector.
machine screws, brown spacers and lock nuts from the©Apply only 2 drops of 3-in-One® oil in each of the ball

steering PCB. bearings. (Each Trak Ball control has five bearings.) Turn

4.Remove the steering PCB.the panel over and roll the balls in all directions. Be sure
5,When replacing this PCB assembly, be certain that thethe oil has not spread onto the shafts.

black toothed wheel turns freely between the two halves of the red photosensor device.

Figure 9 Trak Ball™ Maintenance and Repair

7 @ = Ifthe contacts do not operate sharply or always

  • LED Switch Replacement remain closed or open, then replace the LED switch as outlined in the figure. The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer 2. Trak Ball™ Maintenance to Figure 8. and Repair
@Remove the wires from the suspected switch.To maintain this control, you will only have to
@Set multimeter to ohms scale. Set ohms scalelubricate the bearings approximately every 2,000

to R x 1, then zero the meter. credits. The number of credits can be read off the , a . coin counter, located on the coin door. Use only 2

©Connect multimeter leads to appropriate LEDdrops of 3-in-One® oil in each of the ball bearings.

switch contacts (see Figure 8 for designation (The Trak Ball control has five bearings.) of switch contacts and meter lead placement).

@Check contacts (push and release the switchFor further instructions on how to replace the

button) for closed and open continuity. Trak Ball or either Steering PCB, see Figure 9.

Page 20

Disassemble in the order indicated. (Circled numbers match the steps in Section D.)

Figure 10 TV Monitor Removal

On

D. TV Monitor 2. Unlock and remove the access panel. Slightly Replacement

loosen the wing nuts above the TV monitor (inside the game) that secure the upper retainer strip. Remove the two acrylic TV monitor shields by sliding their lower edges out. NOTE: If you are buying a replacement TV monitor shield, you will receive one %4"-thick shield. This is smoke-colored with white lettering.

  • Working up from the bottom side corners, carefully pry loose the two side ilaps of the colorful cardboard bezel. (A 4-inch strip of double-sided adhesive tape is centered behind both side flaps, flush with each edge.)
  • Open the access panel and unplug the harness connectors for the TV monitor: one is a 2-pin connector in the harness, the other is a 6-pin connector on the monitor’s printed-circuit board. Be extremely careful and never touch the red anode wire or the high-voltage tube on the rear of the monitor! Then unscrew the green ground wire that is attached to the TV monitor chassis. Also unplug the harness connector for
CAUTION High voltages may exist in any television unit, even with power disconnected. Use extreme caution and do not touch electrical parts or the TV yoke area with your hands or with metal objects in your hands! In addition, be sure to use heavy gloves when handling the monitor. You could cut your hands on the metal TV chassis, without such protection.

If you should need to service or replace the color TV monitor, you must first remove it from the game cabinet. Follow the instructions below, and refer to Figure 10.

  • Open the control panel as described in Section C, Opening the Control Panel. Be sure the game is unplugged from its wall outlet! the fluorescent light (located at the left side of the cabinet’s rear opening).
Page 21
  • Remove the four sets of carriage bolts, flat and split lock washers, and hex nuts that hold down the metal TV chassis.
  • Carefully slide the TV monitor chassis out the front of the game. After replacing a monitor, be sure to run the self-test.

-AA— DANGER The color TV monitor does not contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the color monitor on a test bench, you must isolate the monitor from AC voltage with an isolation transformer.

E. Printed Circuit Board Replacement

You may wish to remove the game printed circuit board (PCB) or the Regulator/Audio || PCB for service or inspection. To do this, refer to Figure 11 and proceed as follows: a Open the access panel. Locate the securing screw and fiber washer that hold down the PCB in its slots, and remove them. (Each PCB has one set of this fastening hardware.) If you are removing the game PCB, first remove the two beaded tie wraps that hold the edge connector to the game PCB’s edge. Then unplug the edge connector from the game PCB. If you are removing the Regulator/Audio II PCB, simply disconnect the three small harness connectors on this board. Carefully slide either PCB straight out of its slots. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. Reinstall the PCB, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connec: tor will probably damage your game and will void the warranty.

Figure 11 =

REGULATOR/AUDIO II PCB

GAME PCB

Game and Regulator/Audio |! PCB Replacement

Page 22

UPPER

SPEAKER qv RETAINER STRIP

ATTRACTION PANEL

FLUORESCENT TUBE

Figure 12 Opening the Attraction Panel

-F. Opening the ©

  • Replace the securing screw and fiber washer in

the PCB. Reinstall the tie wraps into the edge Attraction Panel

connector on the PCB. Close and lock the ac- . . . cess panel. Prior to replacing the fluorescent tube behind the . . attraction panel, you will first have to remove the

  • Check that the operation of the game is correct _—_ graphics attraction panel at the top of the Missile by performing the self-test. This is especially Command™ game.
important with any game when you replace a a Normally the only adjustments is the Unplug the game; then remove the three Allen- Missile Gommand™ game are option switch head screws at the top of the game. They secure the changes (made on the 8-toggle DIP switches). metal retainer strip for the attraction panel. Remove Unless you are qualified technician, do not turn the retainer competely. the small knob on the Regulator/Audio II PCB. Tilt the top of the attraction panel towards you, For information pertaining to this control, refer then lift it up and out of the bottom retainer (see to schematic drawings DP-147-01 and -02. Figure 12).
Page 23

If you have to replace the attraction panel, you will probably not be able to remove and save the two wood speaker blocks on it. Be sure to order these blocks, in addition to the attraction panel (see parts list in Figure 19).

  • Replacing Speakers First disconnect the harness plugs for the speakers. Then place the attraction panel on a smooth clean surface, so you don’t scratch the acrylic panel. Replace the speaker, then reconnect the harness connectors.
  • Replacing Fluorescent Tube
WARNING If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

First remove the colorful attraction panel as previously described. Then replace the white fluorescent tube by following this procedure (see Figure 12).

@ Remove the two Y-shaped connectors from the ends of the fluorescent tube. Now carefully remove the tube from its clamps by pulling it towards you. @ Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! @ Close up the game by replacing the attraction panel, retainer strip, and three Allen-head screws.

G. Coin Door Repairs

The new Atari coin door has been totally redesigned, as described on page 3 of this manual. For ease of maintenance, the coin door mechanisms require no adjustments. For plastic mechs, use only hot soapy water to clean them: boiling water is not needed nor even recommended, as this would soften the plastic.

To remove any mechanisms, or to replace the small lamps, switches or trip wires, follow the illutrations and instructions given in Figures 13 through

  • To obtain part numbers for ordering purposes, refer to the detailed exploded drawing of the coin door and parts list in Figure 24.

COIN MECHANISM

Figure 13 Open coin door. To clean or replace a mechanism, locate the black spring clip above the coin switch. Pull this clip towards you, then swivel it up 90°. Push the mechanism towards the right, then pull it out. When reinserting the mechanism, be certain that no wires get caught up in it. Align the mechanism between the top and bottom pairs of vertical tabs in the inner door panel. Push the part of the mechanism closest to you to the left, so both of its round studs slip into the curved notches on the inlet and return chutes. Turn the black spring clip down again to secure the mechanism in place.

‘SPRING CLIP

Removing and Reinstalling a Coin Mechanism

Page 24

SWITCH COVER

QUICK-DISCONNECT WIRES

QUICK-DISCONNECT WIRES Remove the plastic switch cover by squeezing together its two prongs (ust underneath the switch). Tilt the bottom edge of the cover out to the right while pulling towards you and up. Unplug the quick-disconnect wires on the switch and lockout coil. Use a longer-style 1%” socket wrench, so you won’t damage the trip wire, and remove both nuts that secure the coin return chute onto the inner panel. Now hold the return chute subassembly together in one hand, and replace the defective switch. The trip wire can be replaced by carefully prying up the black internal-tooth retainer with a small flat screwdriver. Then remove the wire from the brass-colored stud. Be sure to replace the wire with another of the proper color (four are available, depending on coin denomination). If the new wire is loose when placed on the stud, squeeze the stud’s two halves together with a pair of pliers to secure the wire. Then replace the retainer. Make certain that the wire projects thru the entire width of the coin slot: otherwise no credits will be granted, even for genuine coins. The wire’s normal rest position is against the top of the curved slot.

TRIP WIRE

SWITCH RETAINER

Figure 14 Switch and Trip Wire Replacement

Page 25

COIN INLET CHUTE

LAMP BRACKET @ Remove the screw that secures the lamp and its “Z” bracket to the coin inlet chute. @ Replace the burned-out bulb. Then mount the lamp holder bracket back on the coin inlet chute.

Figure 15 Coin Door Lamp Replacement

H. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.

Missile Command™ is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the TV monitor, Regulator/Audio || PCB, loudspeakers, and control panel.

The Regulator/Audio I! PCB performs two functions: 1) it regulates the +10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio |! PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio Il PCB directly drives the game speakers and is controlled by the volume control, mounted inside the coin door.

The Power Supply is the source of all voltages in the game. These voltages are protected by three fuses (F3, F4 and F5) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power supply chassis.

Figure 16 illustrates the distribution of power in this game. Figure 17 illustrates the distribution of signals.

Page 26

, FLUORESCENT LIGHT

gS oN

COLOR MONITOR

CONTROL PANEL ASSEMBLY

INTERLOCK SWITCHES y-.)

REGULATOR/AUDIO Il PCB

a 2 GAME PCB

COIN DOOR

POWER SUPPLY

an

ISOLATION TRANSFORMER POWER CORD

ON/OFF SWITCH

Figure 16 Power Distribution

Page 27

SPEAKERS

y.

COLOR MONITOR

CONTROL PANEL -

HSYNC. ‘VSYNC, [1 TRAK BALL fm 60

VIDEO

“SS

REGULATORI/AUDIO II PCB

VOLUME CONTROL

SELF TEST SWITCH

GAME PCB

a

COIN DOOR VSYNC

HSYNC

TRAK BALL INPUTS

a S = AUDIO.

Figure 17 Signal Distribution

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

Illustrated Parts Lists

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Atari Missile Command™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists have been arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00-thru 99-, then 000598- thru approximately 110000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 30

Attraction Panel Assy. and Fluorescent Light— i 70-304 See Finire 18 (Fluor. Tube)

035397-01 92.044 (Upper Retainer) (Monitor)

035398-01 (Lower Retainer) 035387-01 (Bezel)

00788201 036235-01 (Interl. Switch Cvr.) (TV Monitor Shield) ‘roche A035802.01 (Main Harness)

“SS

Regulator/Audio II PCB Assembly— See Figure 26 68.002 (Inter. Switch) Control Panel Assy.

002728-01 (Ctrl. Panel Brkt.)

Trak Ball™ Assy.— See Figure 21

: A035791-01, -02 (sol. Transformer), Game PCB Assy.— See Figure 25

75-07017 (PCB Spacer)

A 034536-02 New Coin Door— (Foam) See Figure 24 '035745-02 (Retainer)

A034631.01 (CniOff Switch) A033016-02 Type B Power Supply Assy.— OR A033958-02 See Figure 23 (Power Cord)

19.9032 007103-01 (Vol, Control) (On/Off Switch Cvr.) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL, Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA This drawing is only conditionally’ issUed, and neithe’ receipt nor possession thereof conters or transters any 4021700-xx be Tight in, or iivense to use, the subject matter ofthe Oran (Coin Box) 006870-01 78-3201 ing or any design oF technical information shown thereon, c ‘ nor any right to reproduce this drawing or any. part 030249.01 (Coin Box Brkt) (Cab-Leveling Leg) thereol Except tor manutacture Dy vendors ol Afar, Inc. and for manufacture. uncer the’ corporation's. witted (Geparator) formant , license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation,

Figure 18 Cabinet-Mounted Assemblies A035390-xx D

Page 31

Figure 18 Cabinet-Mounted Assemblies Parts List

Part No. Description

A002465-01 Coin Counter

A021700-01Coin Box Assembly(for all the same coins)
A021700-02Coin Box Assembly(for two different coin denominations—has one separator)
A021700-03Coin Box Assembly(for three different coin denominations—has two separators)

A033016-02 Strain Relief Power Cord (domestic) A033958-02 Strain Relief Power Cord (German) A034631-01 On/Off Switch Assembly A035791-01 or -02 Isolation Transformer A035802-01 Main Harness Assembly (includes on/off switch, 2 interlock switches and their brackets, volume control and its bracket, and single-pole fuse block). Volume control only is part no. 19-9032.

The following four items are the technical information supplements to this manual: DP-147-01 Missile Command™ Schematic Drawings (Sheet 7) DP-147-02 Missile Command™ Schematic Drawings (Sheet 2) ST-147 Label with Self-Test Procedure and Option Switch Settings TM-148. instruction and Service Manual for G07-901 R.G.B. Color Monitor 68-002 Interlock Switch Assembly 70-304 18” 15-Watt Cool White Fluorescent Tube 71-2114 Panel Cartridge Lock Mechanism (for access panel) 75-07017 Spacer for Mounting Printed Circuit Boards 78-3201 Cabinet-Leveling Leg 78-24012 5” Beaded Nylon Tie Wrap 92-044 19” Color TV Monitor 002728-01 Control-Panel Mounting Bracket 006870-01 Coin Box Bracket 007103-01 On/Off Switch Cover 007882-02 Interlock Switch Cover 030249-01 Coin Box Separator 034536-02 Foam Vibration Damper for Game PCB. 035387-01 Cardboard Bezel 035397-01 Upper Retainer Strip for Monitor Shield 035398-01 Lower Retainer Strip for Monitor Shield 035745-02 18” Plastic PCB Retainer 035745-03 10” Plastic PCB Retainer 036235-01 %4"-Thick Acrylic TV Monitor Shield (smoke, with graphics)

Page 32

Fluorescent Light, A035834-01: NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionaly' issued, and neither receipl nor possession thereo! confers or transfers any ‘ight in, oF license to use, the Subject matter of the drawing or any designor technical information shown thereon. nor any right to reproduce this drawing or any pari thereof, Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or ‘the subject matter thereof unless by written agreement with or written permission. from the corporation, 79-561816P 99-11009

A005493-01

99-11011

Attraction Panel Assembly, A035411-01:

035407-01

Figure 19 Attraction Panel and Fluorescent Light Assemblies A035411-01 (A) and A035834-01 (E) Parts Lists

Part No. Desctiption

Attraction Panel Assembly, A035411-01: A035804-01 Speaker Harness Assembly 48-004 5” 8-Ohm 5-Watt High-Fidelity Speaker 000869-01 5” Speaker Grille 035386-01 Acrylic Attraction Panel with Graphics 035407-01 Wood Speaker Block 035420-01 Gasket Fluorescent Light, A035834-01: A005493-01 Fluorescent Light Harness Assembly 70-304 18" 15-Watt Cool White Fluorescent Tube 79-561816P Spring Connector Wire Nut for 16- to 18-Guage Wires 99-11003 Starter, Type FS2 99-11008 5§0/60-Hz Ballast Transformer, with 6”-minimum leads 99-11009 Starter Socket, with 6"-minimum leads 99-11011 1%" Clamp for White Fluorescent Tube 035835-01 12" Y-Lead Connector (2 required per light). Alternate is part no. A036045-01

Page 33

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic written permission of Atari, Inc., Sunnyvale, CA This drawing is only conditionally’ issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the draw ing or any design or technical information shown thereon, Nor any ‘right to reproduce this drawing or any part thereot: Except for manufacture by vendors of Atari Inc... and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation

Figure 20 Control Panel Assembly A035406-01 c Trak Ball Assy.— See Figure 21

A035803-01

Parts List Missile Commani a™

Part No. Description

A035803-01 Control Panel Harness Assembly 62-039 SPDT Momentary Pushbutton Switch, with Red Cap and Light-Emitting-Diode 62-041 SPDT Black Momentary Pushbutton Switch 75-07054 Nylon Spacer 033127-01 Black Molded Switch Bushing 035384-01 Metal Control Panel with Graphics

Page 34

A033360-01 Figure 21 Trak Ball™ Assembly G 85-1808B

Steering PCB Assy.

‘See Figure 22

74-A00011 \ 000616-01

033355-01 034168-01

Page 35

Figure 21 Trak Ball™ Assembly Parts List

Part No. Description

72-1006S #10-32 x 3/8" Cross-Recessed Pan-head Cadmium-Plated Steel Machine Screw 72-1408S, #4-40 x 2" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-1606S, #632 x 3/8" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-8808 #8-32 x 2" Hex Socket-Head Cap Alioy Steel Machine Screw 72-8920S #3/8-16 x 114” Hex Socket-Head Cap Alloy Stee! Machine Screw 73-3006 Carbon Spring Steel External Retaining Ring, for 3/8” shaft diameter 74-A00011 Phenolic Spacer, 1/8” inside diameter x 14" outside diameter x 14" long 75-010S #10 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-016S #6 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-018S #8 Flat SAE-Standard Zinc-Plated Steel Washer 75-040S #10 Steel Split Lock Washer 75-0418 #3/8 Steel Split Lock Washer 75-046S #6 Zinc-Plated Steel Split Lock Washer 75-048S #8 Zinc-Plated Steel Split Lock Washer 75-3608S #632 x 2" Cross-Recessed Flat-Head Cadmium-Plated Steel Machine Screw 75-916S #6-32 Standard Cadmium-Plated Steel Machine Hex Nut 75-919S #3/8-16 Standard Cadmium-Plated Steel Machine Hex Nut 75-990504C #4-40 Shallow-Pattern Prevailing-Torque Corrosion Resistant Lock Nut 85-1808B #8-32 x ¥2” Socket Cap Flat Countersunk-Head Black-Oxide Steel Screw 000616-01 Light Hub 033355-01 Base Plate 033356-01 Top Plate 033357-01 Cover Plate (Acrylic) 033358-01 Corner Post 033359-01 End Post 033361-01 Steering PCB Bracket 033362-01 Roller Shaft 033363-01 Cylindrical Post 033364-01 Adjustable Post 033365-01 Spacer 033366-01 Trak Ball™ 033367-01 Bearing 034168-01 Label with Lubrication Instructions

Page 36

Missile Comman: ™

030369-01

e °

El 0508/-9) RE cEWING BD

Traces shown are ‘on opposite side.

yooso@o ey IAATAO 9

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 79-58005 CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing oF any design or technical information shown thereon, nor any ‘right to reproduce this drawing or any pari thereot, Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

Figure 22 Steering Printed Circuit Board Assembly A009060-02 c Parts List

Part No. Description (Reference Designations and Locations in Bold)

10-5331330 Ohm, +5%, %4W Carbon Composition Resistor(R10-13)
10-53923.9K Ohm, +5%, %W Carbon Composition Resistor(R14, 15)
10-5471470 Ohm, +5%, %4W Carbon Composition Resistor(R7-8)

27-250104 0.1 uf, + 20%, 25V Ceramic-Disk Radial-Lead Capacitor (C2) 29-046 10 uf, + 10%, 20V Tantalum Axial-Lead Capacitor (C1) 34-2N3643 Type 2N3643 Switching Transistor (Q1, 2) 79-58005 10-Contact Connector 030369-01 Radial Optical Coupler

Page 37

46-2038001 46-2022502 4006958-01 7 04 rn ii Ss! eee

TOP VIEW

79-4411004 (F1 thru F5)

29-053 \-78-70501SC aa NOTE: Fuses F1, F2, and F6 are not part of this power supply assembly and must be purchased separately. They have been listed here for your convenience.

BOTTOM VIEW NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, GA. This drawing is only conditionally issued, and neither receipt nor possession thereot ‘confers of transfers any right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor an} Tight to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manutasture under the corporation's writ: ten license, no right to reproduce this drawing Is granted or the subject matter thereof unless by ‘writton agreement with or written permission from the corporation.

Figure 23 Type B Power Supply Assembly A007197-01

Parts List

Part No. Description (Reference Designations in Bold)

A006555-01 Rectifier P.C. Board Assembly

A006958-01Voltage Selection Plug(95V—Black)
A006958-02Voltage Selection Plug(110V—Orange)
A006958-03Voitage Selection Plug(205V—Green)
A006958-04Voltage Selection Plug(220V—Red)

A006886-01 Type B Transformer Termination Assembly A007 192-01 Power Switch Termination A007444-01 Power-In Harness A009266-01 Power Supply Base Assembly 29-053 26,000 uf 15V Electrolytic Capacitor 41-2003 5-Amp Power Line Filter

46-20125012¥2-Amp, 125-Volt Slow-Acting Type 3AG Fuse(F3, F4)

46-2013002 3-Amp, 250-Volt Slow-Acting Type 3AG Fuse (F1*, F2*)

46-20225022%2-Amp. 250-Volt Slow-Acting Type 3AG Fuse(F6*). Alternate is part no. 46-2012502.
46-20380018-Amp, 125-Volt Normal-Acting Type 3AG Fuse(F5)

78-70501SC. 2” Diameter Capacitor Mounting Bracket 79-4411004 Panel-Mounted Non-Indicating 3AG Cartridge-Type Fuse Post (F1-F5) *NOTE: Fuses F1, F2, and F6 are not part of this power supply assembly and must be purchased separately. They have been listed here for your convenience.

Page 38

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the pectic writin permission of Atari inc. Sunnyvale, CA his drawing is only conditionally issued, and neither receipt nor posseasion thereo! confers or transfers any Se10103 right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any ‘right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation 99-10074

Sco ~~

99-10096 75-948S

99-10064

COIN INLET

COIN MECHANISM. SEE PARTS LIST (71-12xxxx)

9910102 65-441C COIN RETURN 4 —99-10065 SWITCH WIRE

CHUTE 99-0068 J SEE PARTS LIST

(99-10075 thru 31-1N4002 99-10078) ‘ COIN SWITCH ASSy. ? PART OF 99-10047 ped 99-10008 ARTS LIST 99-10082 (99-1042 thru 75-14128 99-10045)

Figure 24 New Coin Door 71-10 XXxx PART OF 99-10095

99-10097

Page 39

COIN RETURN BUTTON ASSY SEE PARTS LIST (99-1012 thru 99-10022) 99-10062 COIN DOOR ONLY SEE PARTS LIST (99-10009 thru 99-10010)

99-10049

75-5520B

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING. CONFIDENTIAL” Reproduction, forbidden’ without, the Specific watlen permission of Alar, inc. “Sunnyvale, Caltormia This drawing rs only conditionally issued, and neither reserpt nor possession thereat confers or transiers fany right in, or license to use. Ine subject mater of ihe Gawing at any design or technical information. showr thereon, nar any right to reproduce this drawing or any pat Ihereo! except for manufacture ay vendors Of Ala, Incat porated and for manulacture under the corporation's writ {en ficense, na right to reproduce thre drawing is granted brthe subject maiter there! uniess by wnlten agreament with of weilten permission Tram Ihe corporation REJECT BUTTON COVER SEE PARTS LIST (89-10055 thru 99-1059) PRICE PLATE SEE PARTS LIST (99-1070, 99-10083 thru 99-0092) 99-10074

72-JA1405B

75-915S

72-JA1405B

Figure 24 New Coin Door 71-10xXxxx 7S

72:HA1404C

99-10061

Page 40

a Figure 24 New Coin Door, continued Parts List

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-usage low-force miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism

71-1201MG German 1 DM coin mechanism 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism 71-1205MG German 5 DM coin mechanism 71-1210PE U.K. 10 P coin mechanism

71-1220CA Australian 20¢ coin mechanism 71-1225CU U.S. 25¢ coin mechanism 71-12100LI Italian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C #4x1%4" Slotted pan-head thread-rolling tri-fluted “Taptite” cadmium-plated screw 72-JA1405B #4x5/16” Slotted pan-head thread-rolling tri-fluted “Plastite” black screw 72-9406S #4-40x3/8" Slotted truss-head steel machine screw 72-9603S #6-32x3/16”" Slotted truss-head steel machine screw 75-915S, #¥%-20 Standard pattern cadmium-plated steel hex nut 75-918S #8-32 Standard pattern cadmium-plated steel hex nut 75-9445, #4-40 Polymer self-locking steel hex nut 75-948S #8-32 Polymer self-locking steel hex nut 75-1408S #4-40x 2” Slotted pan-head stee! machine screw 75-14128 #4-40x34” Slotted pan-head steel machine screw 75-5520B #%4-20x1%4" Round-head square-neck steel bolt with black finish 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015, German 2 DM coin return button assembly 99-10016 German 5 DM coin return button assembly 99-10017 Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return button assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 Italian 100 Lire coin return button assembly 99-10040 Coin inlet chute assembly 99-10041 Coin counter assembly 99-10042 Coin switch assembly for U.S. 25¢ and Belgian 5 Fr coins (silver wire) 99-10043 Coin switch assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 coins (black wire) 99-10044 Coin switch assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire coins (gold wire)

Page 41

Figure 24 New Coin Door, continued Parts List .)

Part No. Description (Reference Designations and Locations in Bold)

99-10045 Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coil assembly 99-10048 Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10054 Coin button housing 99-10055 Coin return button cover for Japanese Y100 coin 99-10056 Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S, 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 DM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075 Black switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S. 25¢ and Belgian 5Fr coins 99-10077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 U.S. $1.00 price plate 99-10084 German 1 DM price plate 99-10085, German 2 DM price plate é 99-10086 German 5 DM price plate 99-10087 Belgian 5 Fr price plate 99-10088. Swiss 1 Fr price plate 99-10089 Japanese Y100 price plate 99-10090 U.K. 10 P price plate 99-10091 Australian 20¢ price piate 99-10092 Italian 100 Lire price plate 99-10094 Fish paper insulation 99-10095, Toggle switch 99-10096 “U”-type fastener 99-10097 Fish paper insulation 99-10101 Coin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105 Anti-penny-flip bar

Page 42

SEE DETAIL

-o1 — =03VERSION| (PRON) ~caveRsion| pSStossars mn easel Balo Bus SS16E ENABLE

i ‘f DETAN, TyP. 6 AL

SCALE : NONE

03 version

(PROM)

rail Qe] ape? Peis

SPLIT PAD CONNECTIONS AS DETAILED ARE

APPLICABLE TO USE OF @3IGE'S.USE OF 2708'S

REQUIRE BRIDGING OF OPEN PADS AND CUTTING

OF CONNECTED PADS.

HUNti TE razas

or

= IE IS 3 PL. SD) FaRSIDE NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

drawing or any pari re by vendors of Atal sense, no right to reproduce this drawing is granted or ject matter thereof unless by written agreement {ten permission from the corporation.

D Figure 25 Game PCB Assembly A035467-01 thru -04

Page 43

Figure 25 Game PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

C012294-01 Audio I/O N-Channel MOS/LSI Custom Chip (P8/9) 21-101683 .068 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C65-68)

24-2501051 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C76-79, 98, 100-104)
24-25010610 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C20, 23, 39)
24-250107100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C9, 10, 46, 57, 91)
24-25022622 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C90)

27-250103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C76-79) 28-101102 1000 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C99, 105)

29-088, .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-8, 13-16, 18, 19, 21, 22, 30, 38, 43-45, 47-56, 58-64, 69-75, 80-89, 92-97, 106) 31-1N914 75V Type-1N914 Switching Diode (CR2) 34-2N3643 Type 2N3643 NPN Switching Transistor (Q8) 34-2N6044 Type 2N6044 NPN Darlington Transistor (Q1-3)

37-4584BType 14584 Integrated Circuit(C9, C11)
37-7400Type 7400 Integrated Circuit(C5, D8)
37-74S00Type 74800 Integrated Circuit(A8)
37-7404Type 7404 Integrated Circuit(E6, K7)
37-74HO4Type 74H04 Integrated Circuit(B6)
37-74S04Type 74S04 Integrated Circuit(D7)
37-7407Type 7407 Integrated Circuit(N11)
37-74LS08Type 74LS08 Integrated Circuit(H7)
37-7408Type 7408 Integrated Circuit(R2, J6)
37-74S08Type 74S08 Integrated Circuit(M3)
37-74LS10Type 74LS10 Integrated Circuit(E3)
37-7410Type 7410 Integrated Circuit(BS)
37-74LS14Type 74LS14 Integrated Circuit(D3)

37-7414 Type 7414 Integrated Circuit (J9)

37-7427Type 7427 Integrated Circuit(B7)
37-7432Type 7432 Integrated Circuit(C3, R5)
37-74LS32Type 74LS32 Integrated Circuit(J7)
37-74S32Type 74S32 Integrated Circuit(C4, L5, K6)
37-7442Type 7442 Integrated Circuit(N2, E8)
37-7474Type 7474 Integrated Circuit(H6, A7, E7, F7, J8, A9)
37-7474Type 74S74 Integrated Circuit(A6, B8, C8)
37-7475Type 7475 Integrated Circuit(R7)
37-7493Type 7493 Integrated Circuit(D4)
37-74109Type 74109 Integrated Circuit(D6)
37-74125Type 74125 Integrated Circuit(R6)

37-74LS139 Type 74LS139 Integrated Circuit (P2, M5)

37-74LS153Type 74LS153 Integrated Circuit(F5, H5, J5, K5, P7)
37-74153Type 74153 Integrated Circuit(F3, H3, J3, K3)
37-74LS157Type 74LS157 Integrated Circuit(H2, J2, K2, L2, M2, M7, D9)
37-74S157Type 74S157 Integrated Circuit(E4)
37-74160Type 74160 Integrated Circuit(E5)
Page 44

Figure 25 Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

37-74163Type 74163 Integrated Circuit(D5)
37-74LS163AType 74LS163A Integrated Circuit(R4)
37-74LS166Type 74LS166 Integrated Circuit(P6)
37-74175Type 74175 Integrated Circuit(L8)
37-74LS175Type 74LS175 Integrated Circuit(C7)
37-74LS191Type 74LS191 Integrated Circuit(K8, K9)
37-74191Type 74191 Integrated Circuit(A4, B4)
37-74LS195Type 74LS195 integrated Circuit(M6, N7)
37-74LS244Type 74LS244 Integrated Circuit(A/B1, £2, F2, P5, L9, M9, P10, B/C1, N/P3)
37-74LS251Type 74L8251 Integrated Circuit(N5)
37-748260Type 748260 Integrated Circuit(AS)
37-74LS273Type 74LS273 Integrated Circuit(N6, F9)
37-LM324Type LM324 Integrated Circuit(N10)

38-MV5053 Type MV5053 Light-Emitting Diode (CR1)

62-001SPST Pushbutton Switch(B3)

66-118P1T 8-Station Single-Throw, Dual-Inline-Package Bit Switch (R8, R10) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (For -01 and -03 PCB Assemblies: D1, E1, F1, H1, J/K1, K/L1, M1, M/N1, N/P1, R1, R3; For -02 and -04 PCB Assemblies: H1, JIK1, K/L1, M1, N/P1, R1) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (C2, P8/9) 81-4302 Nylon Snap-In Fastener

90-12310.000 MHz, +.005%, Crystal(¥1)

90-6013 Microprocessor (C2)

90-7005Random-Access Memory(L7)

020670-01 Test Point

035826-01Programmable Read-Only Memory(L6)
100017-001Random-Access Memory(F4, H4, J4, K4, L4, M4, N4, P4)

110000-102 1K Ohm, +5%, %4W Resistor (R1, 2, 4, 13, 16, 21-26, 39, 60, 61, 73, 74, 85, 95, 109-122) 110000-103 10K Ohm, +5%, YW Resistor (R3, 17-20, 30-38, 66-71, 83, 84, 86-88, 93, 94, 96-100) 110000-152 1.5K Ohm, +5%, 44W Resistor (R79) 110000-220 22 Ohm, +5%, YW Resistor (R46, 47, 82) 110000-221 220 Ohm, +5%, %4W Resistor (R72) 110000-222 2.2K Ohm, +5%, %4W Resistor (R76) 110000-332 3.3K Ohm, +5%, %W Resistor (R56-59, 89-92)

110000-27027 Ohm, +5%, %W Resistor(R5-12, 27-29)

110000-331 330 Ohm, +5%, %4W Resistor (R14, 15, 78) 110000-391 390 Ohm, +5%, %W Resistor (R45, 81) 110000-471 470 Ohm, +5%, %4W Resistor (R40-44, 48-55, 80) 110000-472 4.7K Ohm, +5%, YW Resistor (R75) 110000-682 6.8K Ohm, +5%, %W Resistor (R101-108) 110000-822 8.2K Ohm, +5%, YW Resistor (R77) 122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C24-29, 31-37, 40-42)

137002-001Type 74886 Integrated Circuit(L3)
137149-001Type 74LS11 Integrated Circuit(F6, N3)

For remaining memory components and their part numbers, see list on next page.

Page 45

-01 P.C, Boards Figure 25 Game PCB Assembly Parts List

Memory Components and Their Equivalents (Locations Shown in Bold)

-02 P.C. Boards -03 P.C. Boards -04 P.C. Boards (mostly PROMs) (ROMs) (mostly PROMs) (ROMs)

03581201 K/L1 035812-02 K/L1 035822-01 KIL1 03582202 KIL1 035813-01 F1 035813-02 F1

035823-01 UM1 035823-01 LM1 035823-02 LIM1 035823-02 LIM1

035816-01 N/P1 03581602 NIP1 035824-01 N/P1 03582402 NIP1 035817-01 MIN1 03581702 _ M/N1

035818-01 Ri 035818-02 R1 035825-01 R1 035825-02 Ri 035819-01 R3 035819-02 R3

035808-01 H1 035808-02 H1 035820-01 H1 03582002 -H1 035809-01 D1 035809-02 D1

03581001 J/K1 035810-02 J/K1 035821-01 J/IK1 035821-02 J/K1 035811-01 E41 035811-02 E11

Page 46

TRACES SHOWN ARE

ON OPPOSITE SIDE

NOTICE TO ALL PERSONS REC!

CONFIDENTIAL: Reproduction

9 permission of A\

This drawing is only condition

t nor possession thereof confers or transfers any

ise to use, the subject matter of t ‘oF technical information shown thereon,

THIS DRAWING nse, no. the subject with or written permission from the corporation.

  • 2PL. Geer @

Figure 26 Regulator/Audio Il PCB Assembly A035435-03

Page 47

Figure 26 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

12-52P72.7 Ohm, + 5%, 1W Resistor(R5)

19-100P1015 .1 Ohm, + 3%, 7W Wirewound Resistor (R24)

19-3151021K Ohm Vertical PCB-Mounting Cermet Trimpot(R8)
24-2501081000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13)

24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31)

24-3503383300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor(C9, 10, 18, 19)

24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23)

27-250102.001 uf Ceramic-Disc 25V Radial-Lead Capacitor(C2, 7, 16)
27-250103.01 uf Ceramic-Disc 25V Radial-Lead Capacitor(C5, 6, 14, 15)

29-088 -1 uf Tantalum 25V Capacitor (C3, 11, 20, 21) 31-A14F 50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8)

33-TIP32PNP Power Transistor, Type TIP32(Q2)
34-2N3055NPN Silicon Transistor, Type 2N3055(Q3)
37-LM3055V Linear Voltage Regulator(Q1)
37-7812+ 12V Voltage Regulator, Type 7812(Q8)
37-7905,—5V Voltage Regulator, Type 7905(Q9)

52-004 Teflon-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper Wire with .3” Centers 72-1608C #6-32 x 2" Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x %4” Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly

78-16008Thermally Conductive Compound(Q3)
78-16014Thermally Conductive Compound(Q2, 5, 7-9)

79-58306 6-Position Connector Receptacle (J6, J9)

79-583089-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)
79-583544-Position Connector Receptacle(J8)

020670-01 Test Point 034531-01 Heat Sink

110000-0101 Ohm, + 5%, %4W Resistor(R10, 19)
110000-10010 Ohm, + 5%, %4W Resistor(R11, 20, 29, 30)
110000-101100 Ohm, + 5%, %4W Resistor(R4, 12, 22)
110000-1021K Ohm, + 5%, %4W Resistor(R27, 28)
110000-10310K Ohm, + 5%, ¥4W Resistor(R13, 14)
110000-271270 Ohm, + 5%, V4W Resistor(R1)

110000-330 33 Ohm, + 5%, %W Resistor (R3) 110000-392 3.9K Ohm, + 5%, Y4W Resistor (R6)

110000-5625.6K Ohm, + 5%, %4W Resistor(R32, 33)

110000-752 7.5K Ohm, + 5%, %4W Resistor (R7)

110001-221220 Ohm, + 5%, %2W Resistor(R9, 21)

116001-150 15 Ohm, + 5%, 5W Resistor (R31)

122004-224.22 uf Ceramic-Disc 25V Radial-Lead Capacitor(C6, 8, 15, 17)
137000-002Type TDA2002A 8W Linear Audio Ampiifier Integrated Circuit(Q5, 7)
Page 48

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 49

2nd printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name Firm U0 Distributor

Address. 0 Operator City Slate Zip O Other.

Page 50

First fold

BUSINESS REPLY MAIL

FIRSTCLASS PERMIT NO. 1004 SUNNYVALE CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States

Second fold

eBpe siyy odes 2014 Cut along this line ~~

Page 51

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantabil-. ‘ity and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products uhder this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may.sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible forthe quality, suitability or safety of any non-Atari part or any modification including labor which is‘pérformed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for @ any other purpose whatever, and remains the property of Atari, Inc. Neither it nor the information it contains may be reproduced, used, or disclosed to persons not haying a need to know Consistent with the purpose of the loan, without written-consent of Atari, Ino:. SERS ASEM ES SAS AS AN

Page 52

ATARI" ATARI ING 1265 BORREGAS AVENUE PO. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 © TELEX 35-7488 FS svn tonvarncion canon