CATHODE RAY TOMES

Zaxxon Bulletin Joystick Modification Instructions

Zaxxon (set 1, rev D) (Sega, 1982) · Service Bulletin · 3 pages · original scan

Page 1

ZAXXON™ Joystick Modification {nstructions

Turn on the game to be retro-fitted, manipulate the joystick handle

(ITEM NO. 14) to verify proper operation of the 8-way player input

assembly (P/N 834-0236).

Turn the game off, and proceed. The tools you will need are; a small

phillips screwdriver, a pair of dikes (wirecutters), a pair of crimp °

pliers or equivalent, a 3/8" nutdriver, an M4, and an M5 allen wrench (7/64" and 5/32" may be substituted, if necessary), or a “tamper-proof”

screw wrench, if fitted.

With the door to the game electronics compartment open, reach under the

control panel and flip the fasteners on both sides. The panel will now

swing out towards you. Disconnect the control panel harness connector on

the right-side, slide the spring-loaded pins on both sides, remove the

control panel and set on a good working surface (placed upside down on a

padded armchair is ideal, allowing you to approach the underside of the.

panel with ample joystick ciearance beneath).

Notice at the end of the joystick assembly the three wires exiting the

shaft; one green wire, one large white wire and one small white wire.

Note, or mark the gauge difference in the two white wires. At approx-

imately 3" from where the wires exit the shaft assembly, cut all three

wires with the dikes.

Next, remove the four phillips screws (ITEM NO. 16) securing the micro-

switch bracket (bracket 8, ITEM NO. 3) and set aside for re-use: Lift

Page 2

10.

WM. the bracket (ITEM NO. 3) up off of the shaft, and carefully set it back

out of the way.

Using the two allen wrenches, disassemble the joystick handle-halves,

pulling the wire harness through the shaft, and set aside (the handle-half

that mounts the LED and micro-switch FIRE button will be re-used. The re-

worked handle~half is in your kit.

Now remove the. four sets of nuts, washers, and lock-washers securing

bracket A (ITEM NO. 2) to the control panel. Care should be taken here

not to misplace the flat-washers and slider plate (ITEM NO. 13) located,

under the base plate (ITEM NO. 1) upon which the joystick assembly rests.

The replacement bracket A (ITEM NO. 2) can now be rebolted to the control

panel using the flat and lock-washers and nuts removed in Step 7. Check

to ensure that the base plate (ITEM NO. 1) sliding plate (ITEM NO. 13)

and flat-washers are in place.

At this point, tape all three ends of the wire harness together on the LED/micro-switch handle-half, and feed the harness between the shaft “eye”

and through the shaft (ITEM NO. 4} itself. Re-bolt the handle halves to-

gether, taking care to keep the wire harness clear of the shaft "“eye-bolt"

end. We heartily recommend the use of “loc-tite" with all four handle

fasteners.

Re-position the micro-switch bracket B (ITEM NO. 3) over the shaft (ITEM NO. 4) and re-secure the four phillips screws (ITEM NO. 16) removed in Step 5. :

Next, strip approximately 3/8" of insulation from the ends of all six

wires (three wires from the handle, and three wires from the control

panel); twist the two green wires together, twist the two large white

Page 3

12.

13.

14,

15. wires together, and twist the two small white wires together, securing all

three connections with the blind crimps provided in your kit. (The large white wire leads to the control panel FIRE buttons, the smal] white wire

leads to the micro-switches.)

Re-position the now complete contro] panel assembly to the front of the

game, and slide the spring-loaded pins back into place. Replace the con-

trol panel harness connector, rotate the panel into its operating position

and secure the side latches.

Close the game electronics compartment door, turn the game on, and verify

proper operation of your new joystick handle assembly.

If you have any questions, please call:

Toll-free inside California 1-800-722-8576

Toll-free outside California 1-800-854-1938

Using the pre-addressed adhesive return label, place your old joystick assembly parts into the box your kit was shipped in, and return to SEGA/Gremlin.