Moon Patrol Instruction Manual (16-3007-101 Sep 1982)
Moon Patrol (Irem, 1982) · Instruction Manual · 19 pages · 11 sections · original scan
16 -3007-101 Hilhams ® a gal FLL
INSTRUCTION MANUAL
* installation * operation * adjustment
- diagnostics
* parts
FOR SERVICE... Vj “fe °
ROM SUMMARY
CPU BOARD MS2-A-C ROM ROM 0 ROM 1 ROM 2 ROM 3
CHARACTER BOARD M52-B-C ROM 1 ROM 2 PROM 2N PROM 2H
SCROLLING VIDEO BOARD M52-E-C ROM I ROM 2 ROM 3 ROM 4 ROM 5 PROM 1M PROM 2A
SOUND BOARD M52-SOUND-C ROM 1A PART NO. A-5343-09987 A-5343-09988 A-5343-09989 A-5343-09990
A-5343-09991 A-5343-09992 A-5282-09983 A-5282-09984
A-5343-09993 A-5343-09994 A-5343-09995 A-5343-09996 A-5343-09997 A-5242-09985 A-5242-09986
A-5343-09998 DESCRIPTION EPROM 4Kx8 EPROM 4Kx8 EPROM 4Kx8 EPROM 4Kx8
EPROM 4Kx8 EPROM 4Kx8 PROM 32x8 PROM 256x4
EPROM 4Kx8 EPROM 4Kx8 EPROM 4Kx8 EPROM 4Kx8 EPROM 4Kx8 PROM 32x8 PROM 512x8
EPROM 4Kx8
INSTALLATION
Upright Games 1.
nv
= Move cabinet close to desired location and unlock upper rear door panel. Remove the panel and set it aside. Open two trunk latches and swing open lower rear door. Check that all fuses of the power supply board and the line fuse are securely installed in their clips. Unlock the coin door, Reach through the coin door opening and open trunk latches to release control panei. Unhook the control panel safety chain and lower the control panel. Check that the following connectors are firmly seated and that no wires are broken or termination pins are loose in any connector.
. Coin door connector. . Control Panel connector. . Monitor control connector and monitor power connector, . Transformer connector by power panel. . Four connectors on Power Supply board. '. CPU Board 44-Pin edge connector and CPU, Character, Scrolling Video, and Sound boards interconnection cable connectors. Mmonwp
Check that all socketed IC’s on all circuit boards are firmly seated. To check or change game adjustments, locate CPU board (M52-A-C) mounted with other boards on right side of cabinet (as viewed through coin door) and refer to Game Adjustment procedures which follow.
- Extend line cord from game and insert it in slot in lower door frame.
9.
10.
ll. Swing lower rear door closed and latch it. Install and lock the upper rear door panel. Reconnect the control panel safety chain and latch the control panel in position.
Cocktail Table Games
1.
2.
3. Move game close to desired location and unlock and open tabletop. Pull up on two slide latches and lower component door. Check that all fuses of the power supply board and the line fuse are securely installed in their clips. Check that the following connectors are firmly seated and that no wires are broken or termination pins are loose in any connector.
. Coin door connector.
- Control Panel connectors. . Monitor control connector and monitor power connector. . Transformer connector by power panel. . Four connectors on Power Supply board. CPU Board 44-Pin edge connector and CPU, Character, Scrolling Video, and Sound boards interconnection cable connectors. mmouaw>
- Check that all socketed IC’s on all circuit boards are firmly seated.
- To check for game adjustments locate M-52-A-C CPU Board on component door and refer to Game Adjustment procedures which follow. Feed line cord through opening in bottom of the cabinet and pull it through to its full extension. Raise component door and secure with slide latch.
Close and lock the tabletop.
POWER TURN-ON This game MUST BE PLUGGED INTO A PROPERLY GROUNDED OUTLET to PREVENT SHOCK HAZARD and to ensure PROPER GAME OPERATION. Do Not use a “cheater” plug to defeat the ground pin on the line cord, and DO NOT cut off the ground pin. The line voltage must agree with that specified on the back of the cabinet or serious damage to the machine could occur. For low-line voltage applications (105 VAC), refer to the power wiring diagram.
- Plug the game in and turn it ON. The game should come up in the Attract Mode.
- Insert coins, press | or 2 player start buttons and play a game to test control panel switches, sound, and general program functions. If any problems are encountered, refer to Troubleshooting.
GAME OPERATION
Move the Patrol Car from letter A to letter Z (shown at bottom of screen), Control the speed using the joystick. As rocks or UFOs are encountered, press the control panel FIRE button to launch vertical and horizontal missiles to destroy the rock or UFO before you run into the rock or the UFO destroys your Patrol Car. As craters are encountered, press the JUMP button to jump your Patrol Car over them. Rocks can also be jumped. Land mines that appear must be jumped.
SCORING REGULAR POINTS CHARACTER JUMP POINTS DESTRUCTION POINTS
| Small crater | 50 | . | x |
| Large crater | 100 | x | |
| Small rock | 50 | 100 | |
| Medium rock | 80 | 100 |
Large (Double) Rock A. 100 Destroyed 200 B. 100 Half Destroyed 100 C. 100 Half Destroyed & Jumped
| Rolling boulder | 100 | 50 |
| Space plant | 100 | 100 |
| Tank | 100 | 200 |
Regular UFO Xx 100
| Crater UFO | xX | 200 |
BONUS POINTS CHARACTER POINTS (Displayed on screen in Red) UFO formation (3 UFOs) 500 (4 UFOs) 800 (5 UFOs) 1000 Enemy car from behind destroyed 500, 800, or 1,000 (Random) Space Plant Destroyed 300, 500, or 800 (Random)
SPECIAL POINTS
These points are awarded to players who complete sections of the course (Beginner or Champion) in less than average time. On the Beginner course, 1,000 plus 100 points for each “better-than-average” second are awarded. The Champion course awards 2,000 plus 100 points for each “better-than-average” second.
eo
GAME ADJUSTMENTS Game adjustments are made using switches contained in DIP Switch 1 and DIP Switch 2 (Table 1) on the CPU board (MS52-A-C). Using a pen or small screwdriver, move switches to desired positions. Switches 5, 6, 7, and 8 of DIP Switch 1 determine pricing rates as shown. Switch 3 of DIP Switch 2 selects Coin Mode 1 or Coin Mode 2 to go with the settings of switches 5, 6, 7, and 8 of DIP Switch 1. Coin Mode 1 is used for coin doors with a single coin chute or a set of coin chutes of equal value. Coin Mode 2 is used for coin doors with two coin chutes of different values.
Refer to the table for other adjustments. Diagnostics test 01, DIP Switch test causes most adjustments to be displayed on the monitor and may be used while making game adjustments. Note that the sector-selection feature, not recommended as a factory setting, allows the player to start a game anywhere in the Beginner course or Champion course 1.
DIP SWITCH NO. I Table 1, Game Adjustments
SWITCH NUMBER
ADJUSTMENT OPTIONS
| 1 | 2 | a | 4 | 5 | 6 | 7 | 8 |
*RECOMMENDED
| SETTINGS | ON | OFF | OFF | OFF | OFF | OFF | OFF | OFF |
| +COIN MODE | | 2 PLAYS/1 COIN | OFF | OFF | OFF | ON | |||
| 3 PLAYS/1 COIN | ON | OFF | OFF | ON | ||||
| 4 PLAYS/1 COIN | OFF | ON | OFF | ON | ||||
| 5 PLAYS/1 COIN | ON | ON | OFF | ON | ||||
| 6 PLAYS/1 COIN | OFF | OFF | ON | ON | ||||
| *1 PLAY/I COIN | OFF | OFF | OFF | OFF | ||||
| 1 PLAY/2 COINS | ON | OFF | . OFF | OFF | ||||
| 1 PLAY/3 COINS | OFF | ON | OFF | OFF | ||||
| 1 PLAY/4 COINS | ON | ON | OFF | OFF | ||||
| 1 PLAY/5 COINS | OFF | OFF | ON | OFF | ||||
| 1 PLAY/6 COINS | ON | OFF | ON | OFF |
FREE PLAY ON ON ON ON
| +COIN MODE 2 | 1 PLAY/1 COIN | OFF | OFF |
| 1 PLAY/2 COINS | ON | OFF | |
| 1 PLAY/3 COINS | OFF | ON |
FREE PLAY ON ON
| 2 PLAYS/1 COIN | OFF | OFF | |
| 3 PLAYS/1 COIN | ON | OFF | |
| 5 PLAYS/1 COIN | OFF | ON | |
| 6 PLAYS/I COIN | ON | ON | |
| # PATROL CARS | 5 PATROL CARS | OFF | OFF | |
| *4 PATROL CARS | ON | OFF | |
| 3 PATROL CARS | OFF | ON | |
| 2 PATROL CARS | ON | ON | |
| ADDITIONAL | *10,000/30,000/50,000 | OFF | OFF |
| CAR AT: | 20,000/40,000/60,000 | ON | OFF |
| 10,000 ONLY | OFF | ON | |
| NO EXTENDED PLAY | ON | ON |
DIP SWITCH NO. 2
NI
ADJUSTMENT OPTIONS SWITCH NUMBER
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
*RECOMMENDED
| SETTINGS | OFF | ON | + | OFF | OFF | OFF | OFF | OFF |
| FLIP | NO | OFF | ||||||
| PICTURE | YES | ON | ||||||
| **CABINET | TABLE, | OFF | ||||||
| TYPE | UPRIGHT | ON | ||||||
| COIN MODE | COIN MODE 1 | OFF | ||||||
| SETTINGS FOR | COIN MODE 2 | ON |
DIP SWITCH |
| FREEZE | *NO | OFF |
| SCREEN | YES | ON, |
SECTOR-
| SELECTION | *NO | OFF |
| FEATURE | YES | ON |
| DEMO MODE | *NO | OFF |
YES ON
| TEST MODE | *NO | OFF |
YES ON SWITCH 4 (not used) OFF
*recommended settings **For upright games, select ON for switch 2. Table games require OFF for switch 2. +For games with a single coin selector or 2 selectors of the same value, $3 must be turned off. For games with selectors for 2 differentcoin values, $3 must be turned on.
DIAGNOSTICS
Turn switch #8 of DIP switch #2 to the ON position and turn power ON. The MOON PATROL diagnostic program consists of 8 independent tests, 2 of which are automatic at turning power ON in diagnostic mode: RAM Test and ROM Test. After these two tests have been properly completed, pressing the 2-Player button brings an index of the other tests to the CRT display: 01 DIP SWITCH 02 |-O PORT* 03 SOUNDS 04 CHARACTER 05 COLOR 06 CROSS HATCH PATTERN
*Control Panel and Coin Door switches test.
Operate the joystick to position the cursor at the desired test. Press 1-Player Start to initiate the test. As any test other than 02 is completed, pressing the 2-Player button returns the test index to the monitor display. When test 02 is completed, the joystick lever must be moved left while pressing the 2-Player button to return the test index. If no further testing is desired, turn power OFF and return switch #8 of DIP switch #2 to the OFF position.
RAM Test
If checked to be OK, “RAM OK” appears on monitor. If not OK, “RAM NG XXXX YY ZZ” appears on monitor (without ROM test results). Faulty RAM address = RAM Input Data RAM Output Data If RAM is shown to be NG at address EOOO-E7FF, failure can have occurred in either 3B RAM or 2K decoder on MS52-A-C CPU Board. If RAM is shown to be NG at address 8000-87FF failure can have occurred at RAM chip 3C or circuitry directly associated with the RAM chip--Chips 7J, 7K, 6A, 5D, 6D, 4A, 4B, 4C, and 4D on the M52-E-C Scrolling Video board or chip 5M on the M52-A-C CPU board. A faulty chip must be replaced to continue diagnostics.
ROM Test
If checked to be OK, the display below appears on the monitor. “RAM OK” “ROM 0 OK FF” “ROM 1 OK FF” “ROM 2 OK FF” “ROM 3 OK FF” If any are bad, for example ROM 1, this appears on monitor. “RAM Ok” “ROM 0 OK FF” “ROM 1 NG FF” “ROM 2 OK FF” “ROM 3 OK FF”
A faulty ROM must be replaced to continue diagnostics. Certain failure modes of ROMs 0 thru 3 on MP-A-C CPU Board and ROMs 3D and 3F on MP-E-C Scrolling Video Board prevent fault indications from appearing on the CRT.
START
SET SWITCH#8 OF DIP
SWITCH #2 TO "ON"
TURN POWER “ON,
FAULTY RAM OR ROM INDICATED ON MONITOR: REPLACE
YES
PUSH 2P BUTTON
LIST OF TESTS DISPLAYED ON MONITOR (01-06)
SELECT TEST BY MOVING JOYSTICK
PUSH IP_BUTTON TO START TEST
TEST Ol
DIP SWITCHES No
TEST 02 I-O PORT CONTROL PANEL / COIN DOOR SWITCHES NO TEST 03
TEST 04 YES
CHARACTER
TEST OS
COLOR SET SWITCH 48 OF DIP TEST 06 SWITCH 42 TO “OFF
CROSS HATCH PATTERN ° CFinis_)
MP-A-C CPU Board
Green and Blue pattern with “9”s or “6”s - Replace ROM 0 (3M).
- CRT locks up in power-up test pattern - remove ROMs 1 and 2 and repeat test. « /f still locked up - replace ROM 3 (35). * If not - re-insert ROMs | and 2 one at a time to determine faulty chip. MP-E-C Scrolling Video Board + After power up tests, arabic numbers are missing from CRT - Replace ROM 3D. + After power up tests, letters are missing from CRT - Replace ROM 3K.
- Games will power up in Game Over but CRT is blank after power up tests - Replace Color PROM 2A. Since ROMs 3H, 3K, and 3L produce the Scrolling Video, faults in these chips are more easily detected by playing a game, ROM 3H - Cityscape ROM 3K - Near Mountains ROM 3C - Distant Mountains
01 DIP SWITCH TEST
Shows state of all switches contained in DIP switches #1 & #2 and the resulting game adjustments. With the monitor displaying the test index, position the cursor at 01 and depress I-Player Start. DIPSW12345678 swi 10000000 $wW201000101 PATROL CARS 4 ADDITIONAL CARS POINTS 10, 30, 50 THOUSAND
COIN MODE 1COIN 2 PLAYS BODY TYPE UPRIGHT
Troubleshooting Game adjustments can be set and checked using switches contained in DIP | and DIP 2. To make sure all switches are functioning properly, set switch 8 of DIP 2 to the ON position and select test 01 of the diagnostics test index. The video display of test 61 shows the state of every switch in DIP | and DIP 2, and the current game adjustments. A “LP” ON, and “O” OFF for all switches. Switch functions listed below:
DIP SWITCH 1
Switch Function
1&2 Determine the number of patrol cars (2-5) allowed per player per game. If these switches fail, measure resistance between pin | and pins 2 & 3 of RAS, or replace chip 1F. 3&4 Determine the point level (in thousands; 10/30/50, 20/40/60, 10 only, & NO EXTENDED PLAY) where additional cars are earned. For failure of these switches measure resistance between pin I and pins 4 & 5 of RAS, or replace chip IF. 5,6,7&8 Determine the pricing for coin modes | & 2. For failure of these switches, measure resistance between pin | and pins 6, 7, 8, & 9 of RAS, or replace chip IE. If all switches of DIP switch 1 fail, first check voltage at pin 1 on RAS for Vcc, then check switches and associated chips and circuitry.
DIP SWITCH 2
Switch Function
Flips picture vertically when in the ON position to accomodate different monitors. Set it to OFF for all Moon Patrol games. If the picture is flipped anyway, check pins 11, 12, & 13 of chip 6K; measure resistance between pins 1 & 2 of RA6, or replace chip 6K. Defines the game type. Upright games require it to be ON and cocktail table games require it to be OFF For failure of this switch, measure resistance between pins | and 3 of RA6, or replace chip 1H. Determines coin mode | (OFF) or coin mode 2 (ON). Failure of this switch requires measurement of resistance from pin | to pin 4 of RA6, or replacement of chip 1H. NOT USED
Allows selection of Freeze-Screen test feature. Freeze-Screen feature allows the 1-Player Start to start motion of the game and the 2-Player Start to stop motion of the game. Failure of this switch requires measurement of resistance from pin | to pin 6 of RA6, or replacement of chip IF. Permits Sector-Selection programming feature. Failure of this switch requires measurement of resistance from pin | to pin 7 of RA6, or replacement of chip IF. Permits “Demo” mode (allows viewing of entire courses in game play since patrol car is never destroyed). Failure of this switch requires measurement of resistance from pin 1 to pin 8 of RAG, or replacement of chip 1H. Permits Diagnostics mode. Failure of this switch requires measurement of resistance from pin i to pin 9 of RA6, or replacement of chip 1H. If all switches of DIP Switch 2 fail, first check voltage at pin 1 on RA6 for Vcc, then check switches and associated chips and circuitry.
02 I-O PORT (Control Panel/Coin Door Switch) TEST Shows if all controls and coin mechanisms are functioning properly by displaying a matrix composed of the states of switches on the Control Panel and Coin Door. With the monitor displaying the test index, position the cursor at 02 and depress 1-Player Start.
TIMING 0000
The TIMING number starts at 0000 and adds one count approximately every second. If any Control Panel or Coin Door switch is closed a “1” will appear in the above matrix as follows:
1-Player Start Button 2-Player Start Button Coin Switch A P1 FASTER (Joystick Right) P1 SLOWER (Joystick Left) Pl JUMP Pl FIRE P2 FASTER (Joystick Right) P2 SLOWER (Joystick Left) Coin Switch B P2 JUMP P2 FIRE KEY0-1 KEY0-2 KEY0-4 KEYI-1 KEYI-2 KEY1-6 KEY1-8 KEY2-1 KEY2-2 KEY2-5 KEY2-6 KEY2-8
Coin Switch B is present only in games with coin doors that accept coins of two different values. The P2 switches are used in cocktail table games only. To end this test and return to test index: move joystick lever left while pressing the 2-Player Start Button.
Troubleshooting All control panel and coin door switches can be checked (see below) with diagnostics test 02. Also, the display includes a TIMING check which should advance about one count per second.
I-O PORT LAYOUT
| l | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| KEY 0 | LP | 2P | — SERVICE* | COIN A |
START START
| Pl | Pl | Pl | Pl | ||
| KEY 1 | FAST | SLOW | JUMP | FIRE | |
| , | P2 | P2 | COIN B | P2 | P2 |
| KEY 2** | FAST | ~— SLOW | JUMP | FIRE |
. TIMING 0000
- Service switch not provided. ** Player 2 switches on cocktail table games only.
| PORT | PULLUP RESISTOR | CHIP |
| KEY 0-1 | RA3-5 | IE |
| KEY 0-2 | RA3-3 | IE |
| KEY 0-3 | RA3-2 | IE |
| KEY 0-4 | RA3-4 | 1B |
| KEY I-1 | RA2-9 | ID |
| KEY 1-2 | RA2-5 | ID |
| KEY 1-6 | RA2-6 | ID |
| KEY 1-8 | RA2-8 | ID |
| KEY 2-1 | RAI-9 | IC |
| KEY 2-2 | RAI-5 | IC |
| KEY 2-5 | RAI-4 | Ic |
| KEY 2-6 | RAI-6 | IC |
| KEY 2-8 | RAL-8 | IC |
03 SOUNDS Test A list of sounds normally produced by the game appears as shown below on the monitor. With the monitor displaying, the test index, position the cursor at 03 and depress 1-Player Start. Position the cursor with the joystick to select a sound and press the 1-Player start button for repetition of the sound. 01 EXPLOSION (ROCK) 02 PASSING ONE POINT 03 UFO EXPLOSION
- 04 MISSILE FROM CAR . 05 COIN 06 CAR JUMP 07 SPACE PLANT 08 UFO FLYING 09 BACK GROUND MUSIC 10 ENDING MUSIC
- OPENING MUSIC 12 REACHING GOAL 13 CONGRATULATION 14 CAR EXPLOSION
Troubleshooting
CHECK
GND, +5V, +12V, and Speaker connections.
Rotate Volume Control VR1 on Sound Board and listen for scratching sound in speaker.
Touch 3M-3 with one end of an unterminated test lead for speaker clicking sound.
Check that chip 3D-3 remains low for 1 second after power up.
CPU Board chip 1K-12 for low pulse each time 1- Player Start is pushed.
Check that chip 3E-8 and -10 are Jow, and 3E-9 is high when 3D-3 goes high. (This powers up MPU 3E in proper mode.)
Interchange, socketed chips 3F and 3J.
Across each crystal for AC voltage. NO SOUND
REMEDY OR ADJUSTMENT
Fix as needed.
If none, chip 2M or associated circuit on Sound Board faulty.
If none, chip 3M or associated circuit on Sound board faulty.
If not chip 3D on associated circuit on Sound Board faulty.
If no pulse, disconnect Sound Board from CPU and recheck. If still not pulsing, chip IK on CPU Board is faulty. If it now pulses, chips IF or 3J on Sound Board faulty. If pulse present originally, replace plug-in chips on Sound Board one at a time.
If not 2K, associated capacitors, or 3E on Sound Board faulty.
If some sounds are now produced the chip now in 3F socket is faulty.
If none, crystal or associated capacitors faulty.
POSSIBLE TEST POINTS SYMPTOM CAUSE SOUND BOARD CPU BOARD
| Sound | not produced | DO and DI shorted | 3J-19 and-20 | 1K-9 & -6 |
together
| Sounds | & 3 same | D4 stuck low | 35-17 | 1K-19 |
| Sounds | & 3 same & only | D4 stuck high | 35-17 | IK-19 |
sounds produced
| Sound 4 not produced | D3 stuck high | 35-18 | 1K-2 |
| Sound 6 not produced | DO stuck high | 3J-21 | 1K-9 |
| Sound 7 not produced | D2 stuck high | 35-19 | IK-5 |
| Sound 9 not produced | DI stuck high | 3J-20 | 1K-6 |
| Sound 10 not produced | DO or DI stuck low | 35-20 & -21 | IK-6 & -9 |
| Sound 12 not produced | D2 or D3 stuck low | 33-18 & -19 | IK-2 & -5 |
| Sounds 10 and 12 not produced | Di and D2 shorted | 35-19 & -20 | IK-5 & -6 |
together Sounds 2 thru 6 not produced chip IF faulty. Any other sounds missing or duplicated - Chip 1J or IF faulty.
04 CHARACTER Test With the monitor displaying the test index, position the cursor at 03 and depress 1-Player Start. A display composed of 8 tanks verticaily and horizontally flipped as shown below appears on monitor.
= GREEN—TANK—TREADS
fi = RED—GuUN
[_}]=VIOLET—TREAD WHEELS
Troubleshooting Faults in chips on M-52-B-C Character Board result in symptoms as follows; SYMPTOM
Blank Screen
8 green squares
Colors of tank incorrect OR details of tank missing 8 green squares with red wheel hubs, & red tank guns
8 magenta squares with red wheel hubs, red tanks & red tank guns
Colors of tank assembly correct with GREEN OR MAGENTA vertical lines present CAUSE
Chip IF Chip 2H Chip IF or 2H Chip 3N Chip 3M
Chip 3N or 3M
05 COLOR Test
Position the cursor at 05 and depress 1-Piayer Start. This test consists of 5 independent steps (advanced by depressing 1-Player Start) as follows: J. An alphanumeric display is shown as below over a row of numbers 0 thru 9, letters blue and numbers white. ABCDEFGHIJKLMNOPQRSTUVWXYZ 0123456789
- A color pattern is displayed as shown:
RED GREEN BLUE
BLACK
RED | PINK | BROWN | GREEN | CYAN
WHITE
- A field of red is displayed.
- A field of green is displayed.
- A field of blue is displayed. n Each independent step of this COLOR test can be advanced through by pressing the | Player start bution.
06 CROSS HATCH PATTERN TEST
Position the cursor at 06 and depress 1-Player Start. A white line matrix 16 lines vertical x 16 lines horizontal is displayed.
03-7628
otras
Contro! Panel R-9430 Red Button Assembly C-92 14-4 White Button Assembly C-92 14-5 Yellow Button Assembly C-92 14-6 Joy Stick 20-9254 Trunk Latch Bracket 01-6994 Trunk Latch 20-9266 Control Pane! Hinge 20-9447 \ Control Panel Overlay 31-1067-3007-U 3 8 w
| g | gg f | 5 |
| & | geg | g |
| 8 | 2&8 | 3 |
20-6542-T8,
l1-688-3
4320-01123-20;
4700-00033-00.
4701-00005-00. 4608-01080-07 01-7264,
(0-9246) L LIGHT REFLECTOR AssY
5792-09395-00 ($821-0308)-00 PINS) -4108-01001-24
lé MOON PATROL - COCKTAIL
FREL IMI NARY PARTS LIST
DESCRIPTION Cash Box Assembly
Glide with Screw
Monitor/Supports Assembly Cocktail CRT Support - L Cocktai! CRT Support -R 19" Monitor 19K4903
Line Voltage Cable Assembly
Power Pack System 3 "T" Heat Sink Assembly P.S. PCB Assembly Power Pack-T Sub Assembly Transformer Assembly PCB Plate Sub Assembly Power Supply Mounting Board
Clamp & Gasket Assembly - Table Top
Cocktail Brace Assembly
Stud-Shoulder Hinge Cocktail Top Brace
Mask w/Instruction Cards Cabinet Top Hinge Cocktail Top Lock Catch Bracket Top Lock Catch RT Bezel” QT Filter Cocktail Glass Blank Cocktail Top
Control Panel Red Button Assembly, Yellow Button Assembly Joy Stick Control Panel Cover PART NO. D-8603
20-9261
B-9237-1 11-679-3-L 11-679-3-R 5675-09979-00
D-8613
D-9188-3007 C-8809 D-8 784-3007-T D-9275 C-8609 C-9265
B-8692
B-9276
02-4122 20-9262
D-9240-3007 01-7105 01-7190 02-4039 03-7731 03-7752 08-7384 11-679-4
D-9432 C-92 14-4 C-92 14-5 20-9254 31-1070-3007-T
MOON PATROL ~- COCKTAIL
FRELIMINARY PARTS LIST (Continued)
DESORIPTION PART NO. Component Door D-9451 PCB's Assembly A-9436
| Lock Bracket | - Cocktail | 01-7102 |
Door Kick Plate 01-7115 Speaker Gril!-T 03-7622
| PCB Mounting | Block | 11-689-2 |
| PCB | Mounting/Stop Block | 11-689-3 |
Component Door 11-690-2 Speaker 5555-0962 6-00
Coin Door Assembly D-9452
| Light Socket | Assembly | A-8639 |
Lock Link & Stud Assembly A-8650
| Red Button | Assembly | A-8654 | |
| Terminal | Strip | & Diode | A-9103 |
Lock Link/Stud Assembly B-8651
| Coin Door | Lock Guide | 01-7099 |
Coin Door Hinge 01-7103
| Coin | Door Kick Plate | 01-7117 |
Guide Bracket 01-7131 Guide Strip 01-7133
| Lock | Link / | Lower | 01-7134 |
Lock Mech Guide 02-4029
| Coin Mech | - Quarter | 09-1 1000 |
| Cocktail | Coin Door | 11-679-5 |
Cam Lock - Coin Door 20-6542-TB
| Cocktail | Coin Door Cover | 31-1057-3005-T |