CATHODE RAY TOMES

Sky Raider TM-111 1st Printing

Sky Raider (Atari, 1978) · Technical Manual · 112 pages · 43 sections · original scan

Page 1

TM- 11 1st printing

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Catalog

Page 2

GAME SERIAL NUMBER LOCATION

Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the label located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service. tee

Page 3

SKY RAIDER” Operation, Maintenance and Service Manual

Complete with illustrated Parts Catalog

ATARI INC 1265 BORREGAS AVENUE PO. BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2060 * TELEX 35-7488

A

ATARI

Page 4

Copyright © 1978 by Atari, Inc. All rights reserved

Motorola service manual reprinted by permission of Motorola Data Products.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

For permission request, write:

ATARI INC 1265 Borregas Avenue P.O.Box 9027 Sunnyvale, California 94086

3G Lithographed in the U.S.A.

Page 5

TABLE OF CONTENTS

1 rape nie SETUP SOR>

rom INTRODUCTION GAME INSPECTION ... LOCATION OF SERIAL NUMBER INSTALLATION REQUIREMENTS ...... Power Requirements and Line Voltage Selection Temperature Range Humidity Range Location Space Requirement Type of Power Cord INTERLOCK AND POWER ON/OFF SWITCHES SELF-TEST PROCEDURE OPERATOR OPTIONS . VOLUME CONTROL ..

2 GAME PLAY A. B. Cc. ATTRACT MODE READY-TO-PLAY MODE . PLAY MODE

3 MAINTENANCE, AND ADJUSTMENTS in

Ammon CLEANING . 0... cece ccc eee tee nent e tne ee COIN MECHANISM Components on Coin Door Access to Coin Mechanisms . Cleaning of Coin Paths Lubrication ......... Adjustment of Coin Switch Trip Wire .. Mechanical Adjustments on Coin Mechanism ..... General Troubleshooting Hints FUSE REPLACEMENT TV MONITOR REMOVAL .. TV MONITOR ADJUSTMENTS LED START SWITCH REPLACEMENT. CONTROL YOKE ......-5. 00005 Control Yoke Potentiometers .............. Checking Roll and Pitch Bracket Tightness ..

4 THEORY OF OPERATION CARWKHKWKWWHWUNY

Page 6

TABLE OF CONTENTS

5 ILLUSTRATED PARTS CATALOG... B

6 TV MONITOR SERVICING LVFORMATION MOTOROLA Service Manual A. GENERAL INFORMATION .. B. SERVICE NOTES .. Circuit Tracing ... Component Removal . CRT Replacement .. Adjustments Regulator Adjustment ............... . Horizontal Hold/Oscillator Adjustment Vertical Height/Linearity Adjustment Focus Adjustment Monitor Servicing ..... C. THEORY OF OPERATION . Power Supply +73 Volt Supply Video Amplifiers and Output ... D. HORIZONTAL DEFLECTION CIRCUITS Phase Detector ...... . 88 Horizontal Oscillator... . 88 Horizontal Pulse Shaper and Driver . . 88 Horizontal Output : . 8 Sync Circuits ........ - 90 Vertical Oscillator and Output Spot Killer rae a Blanking Amplifier 0.0... ccc ccc ccc tenet terete tenets 91

LIST OF ILLUSTRATIONS

Figure 1-1 Location of Voltage-Changing Plugs on the Power Supply ........ 2 Figure 1-2 Location of On/Off, Interlock, Self-Test, and Volume Control Switches ..... Figure 1-3 Caution Label on Game PCB Figure 3-1 Coin Door Assembly

Page 7

LIST OF ILLUSTRATIONS

Figure 3-2 Hinging Open the Magnet Gate Assembly .. Figure 3-3 Removal of Coin Mechanism ........... Figure 3-4 Surfaces to Clean Inside the Coin Mechanism . Figure 3-5 Removal of Plate Covering Rear of Coin Slot .. Figure 3-6 Close-Up View of Lubrication Point Figure 3-7 Detail View of Coin Switch and Trip Wire .. Figure 3-8 Securing the Coin Switch Trip Wire Figure 3-9 Adjustments on Coin Mechanism Figure 3-10 TV Monitor Removal ...........- 7 Figure 3-11 Locations of Adjustments on TV Chassis aoe Figure 3-12 LED START Switch Replacement ......... Figure 3-13 Removing the Cabinet Light Assembly . Figure 3-14 Bottom View of Control Yoke .. Figure 4-1 Game Block Diagram Figure 4-2 Sky Raider PCB Schematic Diagram (7 sheets) ... Figure 4-3. Harness Schematic Figure 5-1 Final Assembly Figure 5-2. TV Tray Assembly Figure 5-3 Light Assembly .... Figure 5-4 Audio Amplifier Board Figure 5-5 Coin Door Assembly ... Figure 5-6 Power Supply Assembly .. Figure 5-7 R. F. Shield Board Figure 5-8 Sky Raider PCB Assembly . Figure 5-9 Front Housing Assembly Figure 5-10 Control Panel Assembly Figure 5-11 Flight Control Assembly Figure 5-12 Motorola Monitor Modification Figure 5-13 Pot Bracket Assembly ......... Figure 6-1 Motorola Monitor Circuit Board in Service Position Figure 6-2 Motorola Monitor Block Diagram . Figure 6-3 +73 Volt Supply Circuit Figure 6-4 Motorola Monitor Vertical Drive Waveform . Figure 6-5 Motorola Monitor Video Amplifiers and Output Circuit Figure 6-6 Motorola Monitor Horizontal Deflection Circuit Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms Figure 6-8 | Motorola Monitor Horizontal Output Circuit Figure 6-9 Motorola Monitor Sync Circuit Figure 6-10 Motorola Monitor Vertical Oscillator Circuit Figure 6-11 Motorola Monitor Spot Killer Circuit Figure 6-12 Motorola Monitor Blanking Amplifier Circuit Figure 6-13 Motorola Monitor Chassis Rear View—Component Location Figure 6-14 Motorola Monitor Circuit Board Detai/—Solder View .. Figure 6-15 Motorola Monitor Schematic Diagram Figure 6-16 Motorola Monitor Circuit Board Detail--Component | Location ....95

Page 8

LIST OF TABLES

vi Table 1-1 Tabie 1-2 Table 6-1 Table 6-2 Self-Test Procedure 60.2... 60ers Operator Options Motorola Monitor Electrical Specifications .. Motorola Monitor Replacement Part Numbers ..

Page 9

A. INTRODUCTION Sky Raider™ is a one-player jet-fighter game developed by Atari. The game is contained in an upright cabinet which is illustrated with brightly colored graphics to enhance player appeal. A 23-inch blackand-white TV monitor is mounted in the cabinet, with the image reflected by a half-silvered mirror.

LOCATION SETUP

Page 10

A player control panel is mounted directly below the TV monitor viewing screen on the front of the game cabinet. The controls consist of a control yoke and a START button.

The player’s objective is to shoot at and hit as many targets as possible, within the time allowed. Five different types of targets appear at random places, as the player “flies’” over the countryside. A more detailed game play description appears in Chapter 2 of this manual.

As game play begins, the timer (located in the top middle of the viewing screen) begins counting down irom 99. One of four optional times previously set for game length determines the speed of this countdown. See Table 1-2 for specifics on various game lengths and operator options. Play ends when the game time has run out (reached 0). B. GAME INSPECTION

Your new Sky Raider game is manufactured by Atari with the intent of being ready to play immediately upon removal from the shipping carton. Your cooperation is needed to supply the final touch of quality control. Please follow the procedures below to ensure that your game is in perfect condition.

  • Examine all external parts of the game cabinet ior dents, chips, or broken parts.
  • After determining that the game has been received in good condition, unlock and open the rear access door. Carefully inspect the exterior and verify that:

© All plug-in connectors are firmly seated.

IT LINE VOLTAGE 95 VAC 110 VAC VOLTAGE-CHANGING PLUG WIRE COLOR ‘BLACK ORANG installed at factory) GREEN 210 VAC [__220 VAC |

ON/OFF AND C4 INTERLOCK In

3Amp, 250 v. Slow - blow

NOTE: Power supply in your game may not include fuses F3, F4, and F5.

8 Amp, 125v. Fast- Blow

Figure 1-1 Location of Voltage-Changing Plugs on the Power Supply

Page 11
  • The fuses are all seated in their holders.

« No harness wires are disconnected.

  • No loose foreign objects are present, especially metal objects that could cause electrical problems.

Be sure all maior assemblies are checked. Check the game printed circuit board (PCB), the transformer, the two coin mechanisms, the speaker, the player controls, and the TV monitor chassis.

C. LOCATION OF SERIAL NUMBER The serial number for Sky Raider is located on a metallic label in the upper left-hand corner in back of the game cabinet. This serial number also appears in the corner (common to both edge connectors) on the back of the PCB, inside the game cabinet. See inside front cover of this manual.

D. INSTALLATION

REQUIREMENTS

Power Requirements and Line Voltage Selection Sky Raider is shipped for operation at 110 VAC, 60 Hz. Power consumption is approximately 150 watts. However, if your local current is not 110 volts, follow this procedure. You must select one of four connectors at the power supply and plug it into the voltage selection socket. Figure 1-1 shows the four connectors, with one of them plugged in. The plugs are identified by wire color as listed in this figure. Note that there are two basic operating voltages—110 VAC, 60 Hz and 220 VAC, 50 Hz, with provisions for low line voltage in each case. To insure proper operation, measure line voltage. If voltage is consistently below 100 V (for 110 VAC lines) or below 210 V (for 220 VAC lines), use the low-voltage connections.

Temperature Range Location and storage should not be below 0 degrees Celsius (32 degrees Fahrenheit), and no higher than 49 degrees Celsius (120 degrees Fahrenheit).

Humidity Range Relative humidity for location or storage should be no more than 95%.

Location Space Requirements Vertical Clearance—185 centimeters (73 inches) Width Clearance—75 centimeters (29.5 inches) Depth Clearance—91 centimeters (36 inches) Type of Power Cord Atari has added a strain relief power cord to Sky Raider. The advantage of this type of power cordis that, if pulled accidentally, the strain relief will hold the cord in place at the cabinet wail. The plastic strain relief “cushions” the impact of the shock and prevents the cord from pulling the wires out of the harness connector.

E. INTERLOCK AND POWER ON/OFF SWITCHES

To minimize the hazard of electrical shock while you are working inside the game cabinet, an interlock switch has been installed at the rear access door. This switch removes ali power from the game while the access door is open. To help you conserve energy, a power on/off switch has been installed on the game so that it can be turned off during closed periods. Refer to Figure 1-2 for switch location.

Please check for proper operation of the rear access door interlock switch by performing the following steps:

  • Unlock and open the rear access door.
  • Plug the AC power cord into a 110-volt source. (If the voltage is consistently less than 110 VAC, make sure that you change the voltage plug to the black plug.)
  • Set the power on/off switch to the on position by flipping the toggle switch toward the front of the game cabinet.
  • Close the rear access door. Within approximately 30 seconds the TV monitor should display a picture.
  • Slowly open the rear access door until the TV monitor picture disappears. The TV monitor picture should disappear when the rear access door is opened less than one inch from the top.
  • If the results of Step 5 are satisfactory, the interlock switch is operating properly. If the picture does not disappear as described, check to see if the switch is broken from its mounting or stuck in the on position.

M . Close and lock the rear access door.

EF. SELF-TEST PROCEDURE Sky Raider will test itself and provide data to

Page 12

SELF-TEST SWITCH

VOLUME CONTROL ON/OFF POWER SWITCH

Figure 1-2 Location of Power On/Off, Interlock, Self-Test and Volume Control Switches

demonstrate that the game’s circuitry and controls are working properly. The self-test procedure uses the TV monitor and the speakers; no additional equipment is required. We suggest that you run the self-test procedure each time the coin box is emptied. See Table 1-1 for specifics on the self-test procedure.

To start the self-test mode over from the beginning, set the self-test switch to off, then again to the on position. This will return the self-test mode to Step 1,and can be done at any time during the procedure,

G. OPERATOR OPTIONS Options of the Sky Raider game offer maximum player appeal for each game location. These options are listed in Table 1-2. They are preset for a certain game structure during production. To determine how the switches have been set for your game, com-

Page 13

pare the TV monitor viewing screen during the selftest mode with the information in Table 1-2.

To change the toggle positions of the switch assembly and set the desired options, the printed circuit board (PCB) must be removed according to the following procedure:

  • Unplug the game. Unlock and open the rear access door.
  • Locate the radio frequency (RF) shield assembly immediately inside the cabinet on the right. (It is an aluminum box with small holes.) On one end of the box is a printed circuit board with an edge connector coming from the edge of the board.
  • Remove the five pan-head Phillips screws from each of the long sides (total of ten screws) of the RF shield assembly.
IMPORTANT: To prevent damage to the capacitors on the rear side of the PCB, move the board about %-inch towards the edge connector (same direction as the two arrows on the small white label). Then pull the RF board out toward yourself. Never yank the RF board straight off of the metal box. (See Figure 1-3 for caution label identification.)
  • Carefully remove the PCB from the RF shield assembly.
IMPORTANT NOTE

Be certain that toggle 5 on the large DIP switch (located at position L9 on the PCB) is OFF for normal operation of the Sky Raider game. The game will not operate properly if this switch is on.

Page 14

Table 1-1

Test

Number

Instruction

Self-Test Procedure

Results

Test 4 Unlock and open coin door. | TV monitor screen displays*

Set self-test switch (located

inside the coin door, nearest the hinge), to the on position, The positions of this are not marked, but be determined as follows: Moving terrain: play mode Stationary terrain: self-test

mode the following type of image:

Hot “H” represents the horizontal or left/right movement of the control yoke. Turn the yoke to each extremity: the number displayed should vary from 03 or less, to 37 or

more. “V” represents the vertical fast/slow movements of the landscape. Push and pull the control yoke to each extremity: the numbers displayed on the TV screen should again

vary from 03 or less, to 37 or more. “BNS” indicates whether the extended play option was selected (BNS) or deleted (screen is blank in this area). The “L” indicates the lower level of extended play; ‘H”

indicates the higher point level for extended play.

“COIN indicates the particular coin setting, ranging from 0 to 9 and A through F.

“TIME indicates the game length in seconds. “COUNT ____” indicates the total number of game credits accumulated since the Sky Raider game was last powered up. This test automatically checks the operation of the coin circuitry and mechanisms. The credit count is reset to 0 when the game is

returned to the play mode. RAM and ROM are O.K. lustration. scene appears exactly as shown in the above

Page 15

If RAM or ROM is bad, the game will display a letter and number repeated many times across the TV screen. These represent the actual location of the bad chip on the PCB.

Example: K1.

Test 2 Switch Test

Close contacts of slam switch | These four switches will each cause a rocket fire sound.

on coin door

Press each coin switch trip

wire

Press fire button on control

yoke Press START button This switch causes an explosion sound. If no sounds at all result after activating the five switches, then the audio circuit is bad. If some but not all of the switches produce a sound in the self-test, then only the

non-sound producing switches are bad. *The actual image on the TV monitor tube is upside down and laterally reversed, compared to the illustration above. However, if viewing the screen from the normal playing position, the illustration will be correct.

Page 16

Table 1-2. Operator Options ~] Switch Settings on 8-Toggle DIP Switch Option (Located at Position L9 on PCB) Result PI 2[3[4[s5]e 8 y T

Game Instruc-ON.English
tion Language | ONOFF2German
(as displayed | OFFONEsFrench
onTV screen) | OFF |OFFSSpanish

c

Game LengthONON!&60 seconds
OFFON|©80 seconds
ONloFF] &100 seconds
orr|— lorr| 2120 seconds

E 3

Extended PlaySJON2Extended play (50% of regular game length) granted
£JOFF3No extended play granted
{——t&Z
Lower Level5ONIf game length is set at. . .
of Extendedo60 secs.80 secs.100 secs.120 secs.
PlayPaextended play granted for score of:
L313,00018,00027,00034,000 pts.

c

Higher Level2OFFIf game length is set at...
of Extended£60 secs.80 secs.100 secs.120 secs.
Playéextended play granted for score of:
L22,00029,00036,000»43,000 pts.

Setting of 16-Position Rotary Switch, Option Located at K10 on Game PCB Result (Setting is Displayed During Self-Test)

Coin Mode 9 2 coins/play, left and right coin mechanism 1 1 coin/play, left and right 2 2 plays/coin, left and right 3 3 plays/coin, left and right 4 1st coin, one play. 2nd and extra coins, 2 plays/coin. 3 1st coin, 2 plays. 2nd and extra coins give 3 plays. 6 Left: 2 coins/play. Right: 1 coin/play. 7 Left: 1 coin/play. Right 2 plays/coin. 8 Left: 2 plays/coin. Right: 4 plays/coin. 9 Left: Ist coin = 1 play, 2nd and extra coins = 2 plays/coin. Right: 1st coin = 3 plays, 2nd and extra coins = 4 plays/coin A Left: 1st coin = 2 plays, 2nd and extra coins = 3 plays. Right: 1st coin = 3 plays, 2nd and extra coins = 6 plays. B Left: 1st coin = 3 plays, 2nd and extra coins = 4 plays. Right: 1st coin = 7 plays, 2nd and extra coins = 8 plays. Cc Left: 3 coins/play. Right: 1 coin/play. D Left: 1 coin/play. Right 3 plays/coin. E Left: Ist coin = 3 plays, 2nd and extra coins = 3 plays. Right: 1st coin = 6 plays, 2nd and extra coins = 6 plays. F 4 plays/coin, left and right.

Press the reset button, located on the main PCB, once after making any option changes with the rotary switch or the DIP switch.

Page 17

| & caution F! | To avoid damaging capacitors | | on back of this PCB, move 14" | toward arrows. Then pull to- | | ward you I | Assy. No, —|] O° ee —J4

fe) fe}

Row 2

ROW 1

A

H oo Row 1 ie I Row 2 ov00 ° 12345678910)

Figure 1-3

  • Set the switches for the desired options, as shown in Table 1-2.
  • Reinstall the PCB following Steps 1 through 4 in reverse order, Do not force or bend the printed circuit board. Before reinstalling, always inspect the printed circuit board tor damage. Close and Jock the rear access door.
Caution Label on Game PCB
  • Plug in the game and verify option functions by playing it.

H. VOLUME CONTROL If volume is incorrect for your location, open the coin door and adjust the volume control. See Figure 1-2 for location of volume control.

Page 18

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 19

GAME PLAY

There are three modes of operation: attract (power applied), ready-to-play (coins accepted), and play (START button activated).

A. ATTRACT MODE The attract mode begins when power is applied to the game and ends when the proper amount of coins are accepted by the coin mechanism. The appropriate coin and extended play messages appear in the middle of the screen, according to the options which have been selected. All controls and sounds are inactive during this mode.

Page 20

The TV monitor screen displays the view a bomber pilot would have from the cockpit of a jet. The landscape passes underneath the player. A unique feature of this game (patents have been applied for) is the extreme compression of the landscape at the distant horizon, and the “stretching” of topography in the nearest areas. The zooming effect of the landscape is very smooth, with the far distant features moving very slowly and the closest ones increasing greatly in speed.

Throughout this mode, al\ controls are inactive. Player score appears in the upper left corner of the screen as five zeros. The highest score since powerup appears in the upper right corner, alternating with “BONUS FOR “(this represents the extended play level). Below this phrase GAME OVER flashes on and off.

B. READY-TO-PLAY MODE This mode begins when the proper number of coins are accepted (as required by the coin setting determined by the operator) and ends when the START pushbutton on the control panel is pressed.

During this mode, the TV monitor displays exactly the same message as during the attract mode. The START button will flash on and off. Again, throughout this mode, ail player controls are inactive. Cc. PLAY MODE This mode begins when the START pushbutton is pressed and ends when the game runs out. Throughout this mode, all players controls are active. Immediately on pressing the START button, the high score phrase disappears, and the GAME OVER message is replaced with the game timer.

The control yoke operates just like in an airplane. Right/left movement of the control yoke causes the crosshair sight on the screen to move either to the right or left. As game play progresses and more points are scored, this rocket sight moves slowly towards the top of the screen, causing the player to see less far ahead. With less time to anticipate the various targets, the difficulty increases.

Up/down movement causes the landscape to increase/decrease in speed. Pushing the firing button on the right yoke handle will release a single rocket or a stream of rockets (if depressed for more than a moment) aimed at the sight.

The randomly appearing targets are rated as follows: Tower 350 points if hit Bridge 450 points if hit City 450 points if hit Oil Refinery 450 points if hit Enemy Plane 800 points if hit

Any target that the player hits will explode and momentarily display the point value scored.

Page 21

Due to its solid-state electronic circuitry, this Atari unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical background.

NOTE If reading through this manual does not lead to solving a specific maintenance problem, you can reach Atari’s Customer Service Department by telephone Monday through Friday, from 7:30 a.m. to 4 p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984-1900; from the remaining 47 states call (800) 538-6892 tollfree.

If you are interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator's Handbook, manual number TM-043. This book is available from Atari, Inc., Attn. Customer Service Department, 2175 Martin Avenue, Santa Clara, CA 95050 for $5 each, or from your distributor.

ADJUSTMENTS

Page 22

A. CLEANING The exteriors of game cabinets and plex panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the plex panels because any dust can scratch the surface and result in fogging the plastic.

B. COIN MECHANISM Components On Coin Door Figure 3-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. During the attract mode the microcomputer energizes the lockout coil, causing the lock-out wires to retract far enough to allow genuine coins to reach the coin box. But during the ready-to-play mode when the LED is lit, and during the play mode (and also when AC power to the game has been turned off),the lock-out coil is de-energized, causing the lock-out wires to move out far enough to divert coins over to the return chute.

Lamp Holder Coil Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.

Also shown in the photograph is a slam switch assembly. It has been included to discourage any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.

Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 3-2. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pushing down ona release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 3-3.

Figure 3-1 Coin Door Assembly Figure 3-2 Hinging Open the Magnet Gate Assembly

Page 23

Figure 3-3 Removal of Coin Mechanism

Cleaning of Coin Paths

CAUTION The use of an abrasive (such as steel wool ora wire brush) or a lubrication on a coin mechanism will result in arapid buildup of residue.

By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air. Figure 3-4 shows the surfaces to clean inside the coin mechanism. These include the inside surface of

(Clean both surfaces where coin enters the mechanism, as well as the magnet) Figure 3-4 Surfaces to Clean Inside the Coin Mechanism the mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.

If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a %-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 3-5). Removing the plate will provide access to the entire channel.

Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.

Removal of Plate Covering Rear of Coin Slot Figure 3-5

Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 3-6 shows this lubrication point.

Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 3-7. Use extreme care when handling or touching these wires.

Page 24

Manually hold down rejection button and apply one drop here

Lock-out Wire

Figure 3-6 Close-Up View of Lubrication Point

Three problems can occur with trip wires—they can be too long, too short, or become loosened and fall off.

Correctly adjusted trip wire

Figure 3-7 Detail View of Coin Switch and Trip Wire CRIMP TOGETHER MOUNTING STUD AT 2 ARROWS SHOWN a

Figure 3-8 Securing the Coin Switch Trip Wire

With a wire that is too long, you may have a problem of it catching on the opening in the cash box as a coin is accepted. You can Cut off the end of the wire in small increments, making sure it still extends slightly through the V’ of the coin chute.

If the trip wire is too short (either by wrong adjustment or by being cut off too much), coins may slip by the wire without tripping it, and no credits will be given. The solution is to carefully bend and straighten out the wire to lengthen it. If you cannot straighten it sufficiently, contact your distributor to order another trip wire.

If the wire is loose and falls off its mounting stud, it will also cause no Credits to be given. Secure the wire by crimping-together both ends of the brasscolored mounting stud with a pair of pliers (see Figure 3-8). If you should ever need to remove the trip wire, the two halves of the mounting stud can be separated with a small screwdriver.

Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean well-lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure3-9 shows an expioded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These

Page 25

ITEM IDENTIFICATIONS Kicker and Separator Screws Washers

Lever Spring Gate Pivot Pin Mainplate Assembly “C” washer Rail Gate Assembly Cradle Assembly

Upper Gate Pivot Spring Undersize Lever Assembly Magnet Gate Assembly Magnet Gate Adjuster Retaining Screws Coverplate Assembly Return Coverpiate Coverplate Mounting Studs Pivot Spring Kicker and separator

  • Set the acceptor with the back of the unit facing you in the test position.
  • Loosen the kicker and Separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
  • Insert several test coins (both old and new) and note that some are returned by striking the separator.
  • Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted.
  • Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
  • Insert the test coins and note that some are returned.
  • Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted.
  • Be sure that both screws are tight after the adjustments have been made.

Magnet gate

  • Set the acceptor with the front of the unit facing you in the test position.
  • Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through,
  • With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
  • Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted, . Fix the magnet gate adjusting screw in this position with a drop of glue.

Additional Cleaning

  • Remove the transfer cradle (12) and the undersize lever (14).
  • Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
  • Replace the transfer cradle and the undersize lever.
  • To be certain the coin mechanism is completely free of any residue, place the mechanism in boiling water for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.

Figure 3-9 | Adjustments on Coin Mechanism

Page 26

adjustments should only be done by someone who has experience in servicing coin mechanisms and who understands their operation.

General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.

C. FUSE REPLACEMENT Sky Raider contains seven fuses, five on the power supply assembly in the lower part of the cabinet and two on the TV monitor assembly. All fuses are easily accessible through the rear access door. Replace fuses only with the same type of fuse as follows:

Motorola M7000 Monitor: 3AG 0.8-amp quick-blow, 250 volts Power Supply: Fuses F1 and F2—3AG 3-amp slow-blow, 250 volts Fuses F3 and F4——3AG 2.5-amp slow-blow, 125 volts Fuse F5—3AG 8-amp fast-blow, 125 volts

D. TV MONITOR REMOVAL (Refer to Figure 3-10) Remove three screws (button-head socket cap #10-32) at the top edge of the cabinet and remove the Plexiglas*retainer. Then remove the Plexiglas screen and the cardboard bezel. Be sure to reconnect the ground wire when removing the bezel. At the back of the cabinet, remove the rear door which is secured by four wood screws. Remove the four carriage bolts which secure the monitor to the TV shelf assembly. Disconnect the TV monitor harness and slide the monitor out through the front of the cabinet. E. TV MONITOR ADJUSTMENTS

CAUTION For best results be sure the game has been turned on for a while before making any TV monitor adjustments. |
NOTE The TV monitor adjustments are accessible through the rear door pane! of the game cabinet. These adjustments have to be done while the game is energized. Therefore, only persons familiar with safety measures and repair procedures on electrical equipment should perform them.

The TV monitor should be adjusted only when the picture is distorted or if the contrast or brightness seem out of adjustment.

The monitor's adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure 3-11 shows the location of the adjustments on the TV monitor used by Atari. When making adjustments, follow these general guidelines: BRITE (Brightness) —Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up. CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being blurred. HORIZ OSC (Horizontal Oscillator)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture.

F. LED START SWITCH REPLACEMENT (See Figure 3-12) Unlock and open the coin door. Disconnect the control panel cable connector and remove the four hex nuts (two bottom and two top) securing the control panel. Note that a ground wire is secured under one of the lower hex nuts. The LED switches are accessible when the panel has been removed. Remove the wires from the suspected switch and turn the switch counterclockwise while holding the

Page 27

Step 2

Step 3

Step 4

Step 5 Remove Screw.

Remove wood screws.

Reach through coin door and remove two securing nuts (and screws) from front of TV shelf assembly.

Unplug Molex connector from TV monitor chassis.

Lift back of TV shelf assembly and slide out of cabinet.

Figure 3-10 Removal of TV Monitor

Page 28

cone-shaped nut on the outside of the game cabinet. Install a new switch using the reverse procedures. Reconnect the harness wires. When reinstalling the panel, be sure to secure the ground wire as before.

‘CONTRAST — Honuz. osc. FOCUS 2 FUSES ~ REMOVE. COVER To REPLACE (botm 0.8.8 quexbiow) BRIGHTNESS

MOTOROLA MODEL M5000/M7000

Figure 3-11 Locations of Adjustments on TV Chassis

G. CONTROL YOKE

Control Yoke Potentiometers The control yoke has two potentiometers. These potentiometers supply player steering information to the game PCB. With a good amount of use, these potentiometers may eventually become dirty and require cleaning. To clean, use a tuner cleaner. This spray Cleaner is available at most electronics supplies stores. When you buy tuner cleaner, make sure that you get the thin nozzle extension tube that comes with the spray can.

For cleaning the potentiometers, remove the Control Panel Assembly (see Figure 3-13). Insert the spray nozzle extension tube into each potentiometer, spray, then work the control yoke to make the potentiometers rotate.

The two potentiometers in the control yoke are self-adjusting. Whenever the yoke is pushed to the top/bottom or right/left limit (even during the attract mode), the microprocessor program senses these points and automatically determines the center position for both directions of movement. Therefore, you do not need to perform any calibration of the pots.

Checking Roll and Pitch Bracket Tightness Make certain the Control Panel is firmly attached to the cabinet. It is hard to communicate how to check for tightness. The only thing we can say is that if the brackets are just a little loose, the Control Yoke will feel sloppy.

The best method of determining if the brackets are loose is by removing the control panel and trying to wiggle the brackets. If the brackets are loose, disassemble the control yoke as instructed in Figure 3-14 and tighten the bracket mounting screws to 20 (+ %, —0) inch-pounds. Reassemble the control yoke as instructed in the figure.

START SWITCH

  • Unlock and open the Coin Door.
  • Disconnect control panel cable connector; then remove four hex nuts.

Remove wires from suspected switch.

Turn switcn counterclockwise while holding cone-shaped nut on outside of game cabinet o Install new switch using reverse procedure.

Reconnect harness wires.

Figure 3-12 LED START Switch Replacement

Page 29

REPLACING THE BLACK LIGHT TUBE

Remove the Front Housing Assembly as follows:

  • With a 7/16-inch wrench, reach through the coin door and remove four 14-20 hex nuts, one at each corner of the Contro! Panel Assembly.

. Disconnect the harness connector from the Control Panel Assembly, then remove the Control Panel Assembly.

. With a 0.125" hex wrench, remove three #10-32 x 1inch buttonhead screws and the metal seam cover from the top of the Front Housing Assembly. METAL SEAM COVER . Lift off the Front Housing Assembly.

. With a Phillips-head screwdriver, remove two #8 x 1.5-inch wood screws from each side of the Display Light Assembly.

. Pull Display Light Assembly out of cabinet far enough to remove the black light.

'. Re-assemble the cabinet, performing steps 1 through 6 in the reverse order.

DISPLAY PLEX ‘ GRAPHICS PANEL . ™ ~ M/ NN ™ ISPLAY LIGHT ASSEMBLY

SEMBLY

REPLACING THE FLUORESCENT TUBE

  • Remove the Display Plex Graphics Panel by using a 0.125-inch hex wrench to unscrew five #10-32 x 1-inch socket head screws.
  • Remove the fiuorescent tube.

Figure 3-13 Removing the Cabinet Light Assembly

Page 30

‘CONTROL YOKE HANDLE

conrRoL, YORE: HOUSING

‘CONTROL YOKE SHAFT- TIGHTEN TO 20 (%, 0) INCH-POUNOS

  • REMOVE TWO MOUNTING SCREWS FROM BOTH THE ROLL BRACKET AND PITCH BRACKET #2.
  • REMOVE ROLL PIN.
  • PULL CONTROL YOKE SHAFT OUT OF CONTROL YOKE HOUSING FAR ENOUGH TO TIGHTEN PITCH BRACKET #1 MOUNTING SCREWS TO SPECIFIED TORQUE. 4, RE-INSERT CONTROL YOKE HANDLE INTO CONTROL YOKE HOUSING AND INSERT ROLL PIN.
  • MOUNT PITCH BRACKET #2 AND ROLL BRACKET, AND TORQUE SCREWS AS. SPECIFIED.

Figure 3-14 Bottom View of Control Yoke

Page 31

OPERATION

The block diagram in Figure 4-1 shows the major parts of the Sky Raider Game. The game’s television monitor is a self-contained transistorized unit. The composite video signal sent to the monitor differs in many respects from the signal derived from commercial TV broadcasts. The picture appearing on the screen, therefore, is unlike that of a home TV set and the monitor does not produce any sound. See Chapter 6 for a schematic diagram of the TV monitor. The game's composite video signal produces four video levels instead of the continuous shades of grey seen on a home TV screen.

Page 32

ac SOURCE HORIZONTAL SEFLECTION twrensrry 4 || KEYING PERTICAT DEFLECTION wv MONTOR cincumrRY

composite. VIDEO

SPEAKERS.

Figure 4-1

On the game PCB schematic diagram, Figure 4-2, the symbol “P” (appearing at various inputs of integrated circuit devices) indicates a connection of +5 volts DC through a pullup resistor. For easy reference, the game PCB is divided into grid sections. Along the short side of the board these sections are identified by letters A through R (skipping letters G, I, Q and Q because they may be easily confused with Game Block Diagram

the numbers 6, 10, and 0 respectively). Along the /ong side of the board the numbers 1 through 10are used.

Figure 4-3 is a harness schematic of the entire Sky Raider game. This figure illustrates how all electrical and electronic assemblies are electrically connected together.

Page 33

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 34

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 35

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL Reproduction lortaden without tne specific writen permssian at tary Inc Sunnyvale Calarma This arawing ie only condihonally yssued aii naither receipt nar possession there confers or wansters any night in or license to use the subject matter of the Grawng oF any design or techacal Information shown thereon norany right ta reproduce hisdramagur any part erent excep! for manulaciure by vendor af Alan incor porated ang lor manutasture under the vosporation Swit Tenlicense. no ight to raproauce misarawangis granted oF the subject matter thereo! unless by wrllen agruement su oF written permasion from the corporation

266H VBLANE

Blan4o ”VRESET

a Veeset

aly9ysyne

73} 3 — vewne

tay38 iVBLANK

24 G8 — vecane

TRA

SYNC. POWER

LAST DES

cao NOT USED

R127

ern

a6

vi

igure 4-2 Sky Raider PCB Schematic Diagram Sheet 1 of 7

Page 36

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 37

NOTICE 4O ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reprocucuon forbieden without Ine specific writen permission of Atari. inc. Sunnyvale Cahlorrua This drawing 8 Only condivonally issued. and ewer receipt ner possession thereat confers er transters| any right in-of license 10 use, the subject matter oi tne Srawing oF any design oF technical information shown COUNT TIE RESET tereon, norany “ight 6 reprocuce this drawing or any par! Inereot exceat for mancracture by vendors of Atari Incor g To porated ang tor manulactere under tre corporation swt

nice=aften icense na righ fo reproduce ths drawings grante sor
°feythe sujec! matter thereot unless by written agreement
PRBSTol®‘with oF wilten permission tram the corporation
ltrgelt—tlenneinEsomthetorn

calf ster afer Use! : \ [os ge acon t 2a a8 @c aL fate feb [9 Tate tepe [> Pros res! count 26

3]

VFogare®

3] zo

ag

tsi4 cone

ouN

TERRAIN YFG, TRAPEZOID

Figure 4-2 Sky Raider PCB Schematic Diagram Sheet 2 of 7

Page 38

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 39

+sY SCRAMOD

Re ie

7a,8

oe i 3 2

La34KaoF

ey

saz7 isLs423
-aeia
Kcaaa

is oT =

NCS83/27
isZhe8),a
ABA8Pain
piu03aa
tele |,arsCew

A 2 be

volE4>7
anealiEese
Lsoo2RANGE

si4 33.3 le sae WATCHDOG tial. ae zlz ——

DBalszOFFSET

aig—— 02 _ aie roe oe

istei5
Aesiaaye

cu

ep

He

#3 Lsde

AZ ——* 8

i

ailSAfi

_ it

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction foraidden without the Specie writen permosion of Atari Ine, Sunnyvale Caiforna Ths drawing s only conditionally ssued_ ard Aeliner receipt nor possessian thereat confers or wansters ny rant in'0F heenee Wo use. the subject matter ofthe ‘Srawing or any dengn or technical information shown tmereon. nov any rightto reproduce this drawing ovary part thereat except for manulacture oy vengors of ArNCO porated and lor manulacture under the corporation s wet . . +: fen license. ng right toreproduce this drawings granted oF Figure 4-2 Sky Raider PCB Schematic Diagram the subject matior hereotuntess by writen agreement vwth-oF watten permission Irom the Corgoration Sheet 3 of 7

Page 40

Gallorrsa This drawing 15 only conditional esther receipt nov possessien thereot confers ot isnsters any night on oF license £0 USE the subject mal drawing of any desig” oF lechncal information shown therean nor anyrignt to reproduce tins srawirig ot any patt tmereot except tor manutacture by vendors at Alar incor porated and lor manutacivre uncer the carporation $ wrt Feniicense nongnttoreproducetn's growing is granted o° ine subject matter thereat uniess by silten agreement with or written permission trom tne corporation REPLACEMENT CIRCUITRY FOR -O1

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction forbigoan without ime speciic writen permission of Atari In

tevsev+5V+5vtevtev+evsy
1218sahahe18jieie
a1utMisiLia“Pa

230593 |030892 | 030591 | 030500 | 030569 | 030888 | ox0se7 | or0se6

agis]17000)[Tersoer | Oeoer | Geo0r | “Ce00) | Gaoer | Ceoes |, coor

we ra As

ay—|A7

ae ke As Ike

AS3Ad
AB4.Aa
AzZAz
AL“a

ae Aa Boa B07 ¢ hz ap2—# he — Boe

Boi—Paced
Boe—===ede
wieeFad

Ase ue Romi + ROM?

tevFV RZcngBRD.

Jeo re lie

su=x
BRINSlaqay [2RWWVZU aw4ar
acaate24a8ae
as-—anay}?£8) asay—2YazpeiHeul — prvin
says?aepele+Yaspapdoa
ea2—2 2B csoe_Zed, val"1D]~ LSi4

le f

pa 2betats a vetrat
tov<valeoatAe &py be12er le}
TeeleShy8714)
VeenF2 as—ar 2 07]“=
zeJan 8s__}
lace=
3_eRe

r > RZ

a3‘3aay/8

az—t“laa aye»

ALFleawft
Ag2aitp

10] 45 £3, we le

oatEs|z feaw

32H 48 @H—

ve $F} 28ExaH
enya2soH8
bs|Vere—4{**
hye‘ere |“v2)53°
VeraNK 4+!=i—_
|ant1vay —¥
i_3i

2 av

a 3 1 ]

V BLANK,ae«s

a 3

=des)oe—+
woozLpu

eps

abe272

avg eps} ie rhe l us ‘Sunnyvale. PF 'ssuee ane

Page 41

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 42

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 43

commas

ns oy é : ¢ ont? BULLET eS rsh tine 12), Lsiee me ole micas pomsa -—____I*P 7" *]:

af, i a mi aw so} L i 4 Sip Rice

  • cary 2 a 2 AL _ Zeca P 7 ps eft

MISSILES

MOVING OBJECT CONTROL NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the Specific writen germession oF Ataei In: Sunnyvale Gahlornia This grawing 18 only Condivorally sued anc ether receipt ror possession thereof confers or transters any night in cr license {0 ush the suDject matter of the Srawing of any design or technics iMormaten shown thereon narany night to reproduce mss drawing or any oar! thereat except for manutacture by vendors af Alar Inco: fporalecand for manutacture under the corgoralion s wit fen license no right to reproduce this drawing suranteg or tine subject matter tnereot unless by written agreement swan or written permission trom tne Eorporstion

MOVING OBJECT CONTROL, MISSUES

Figure 4-2 Sky Raider PCB Schematic Diagram Sheet 5 of 7

Page 44

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 45

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reareduction forbidden without Ine Specific wntlen permission of Atari In. Sunnyvale Calilorms This arawing vs only conditionally sued ane neuer receipt nor possession there! confers ar Hansters Any night im-oF license lo use the subject malier of the Grawing oF any design or lechnical information shown Inereon norany nant lo rantadtuce thus drawing or any part Inereo! except lor manufacture by vendors of Alan Mca porated and for manulaciure under the corporation swt Ten license na nght ta renrortuce tis rawng rs granted oF

ssv

. R1e RIL 410 $0

aa iA Boe

\@ Slang 2x}7 Bp: xs 5 he cs. Port ue e7sl2_tl, woe ‘olss ror ne (a 0 t in ws com cure [6 oan

VIDEO . INPUT-OUTPUT

Figure 4-2 Sky Raider PCB Schematic Diagram Sheet 6 of 7

Page 46

4sv +5v EXPLOSION.

atk 10 aes ts Blas ol b8iex auf? Sick :

2hef
Ta Heacl?el
byeeae eeale aft

“FT je ho PRU IC io

7oswsie

anf we

ande ols t Wa ale2
8hlaAoe
Itn alfle al |e a]
onaasoe

RAVDOM era WOise Caf 5 RESET L3¢eulfe “etla Teee Ebi fe ose

tsv

ano get, tr aol? ad A ee aie 8, Ey ae Rat LSied ae? a [th

PLANE sweer-svA galt

o ol | ae , A aa 15M

au An hey aa Ble alt PLANE OUT acf® 7 le e Vex Oe Rai sia oe ‘ Ci 8 oof f a?) ete a |

one MSLA

  • Blog see acl= Rs ale. ool aie? «1 le Ra Listes wr pA ort sv z iz Bog on wesc

oe ele gat oc = 5 ate aoe eal Ral | Lsied of? tila ft car oF i es r ont 2 MSLB

Page 47

R22 Rue aus

230K ev 13K

E10 4 azo 693 ate aaNet A NV 322) 20K Tt lo lees i ait -3v K ase

era Wy bene

JETR 4

R30 a’ mst: wn

Ra MSLB rv

Sr

Do

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden withoul the Specitic watien permission of tan inc Sunnyvale Calormia Thig drawing #s only condimunally sued and ‘either receipt nor passesstan theweal conta or transiurs, any nigh in_o1 license 19 use tne subjuct matter al the ‘éraming oF any design or technical information. show Inereon nor any right to vepvoguce nis drawing any pat! Inereot except for manutseture by vendors of Ala Mic ovated and far manutaciure under the corporation s wit lenticense novight reproduce is Qrawing granted ur Ine subject matter thereot unless by wntten aqrvonen vwiin oF written permssion trom the corporation atreact——fde24 ee Rus

3 + TW] AIO

act

Aupio cs GND

Figure 4-2 Sky Raider PCB Schematic Diagram Sheet 7 of 7

Page 48

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 49

FLUORESCENT

Bk7)Bk,

GN 2 [ene wf opes tw 4 LIGHT

ponyek.JeeTot)sx
Sorz[GNFoNac
3] Www3Tw

FOR + POWER re wa BLACKLIGHT ‘SUPPLY Te SeHEMATIC iM S Ml E 007197-01 Tr

oyfoujekBK
our|%3lwoF~foi6a 87 bio

—— poe 25 08 oll 7 03 06 99 ol2 co MONITOR

elo!) Bulw

  • BN/w E14 ape SL RIw el & TIBK/Ww Bl eK 7 at Yaw

0] oa] oll 2lon

1 COUNTER ofezp LT [°3) COIN SWITCHES #2 bxior* ! OR/BK, boc fONO, oR BK N.C,

CONFIDENTIAL Reprod TR

Any night in oF licange te use Me subject matter Grawing or any sesign or technveal imormation thereer norany ngnti9 eepraguce this raming o

font or written permasion fran the Corporater NOTCE TO ALL PERSONS RECEIVING THIS DRAWING

of tary Ine Sunnyvale California Ths grawing is only conaitionally sesued ane jassessian thereo! conters ar Wansters

Figure 4-3 Harness Schematic

Page 50

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 51

ILLUSTRATED PARTS CATALOG

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for the Sky Raider game.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this list, and the serial number of your Sky Raider game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

If there are any questions about this list, please contact Atari’s Customer Service Department by telephone Monday through Friday, from 7:30.a.m. to 4 p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984-1900, from the remaining 47 states call (800) 538-6892 toll-free.

Page 52

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING

See SHEET Zoe Ly SAE NAME.

Page 53

TARE OF Tea © LeCaTen TOP, AZONT

nt een a ere

2 620(3) NN AN a— || . N Ne N ess 4 Rea (3) \ ’ LRG > ae 11.00 Figure 5-1 Final Assembly AffRox. A008569-01 A

Page 54

ATION p *

POSITION OPEN SIDE OF ==

ON-OFF SWITCH ENCLOSURE. (ITEM 39) TOWALDS THE REAL. OF THE CABINET. 2.

i L

io LLEIITTT ITS T TINT TTT EST ATLL LL

Page 55

' : AUGN LOWER BOGE road OF BEZEL WITH THe BEIGE OF THE TN MOUNTING SHELF,

AN stapie iw PLACE (FOUR PLACES AS NOTED)

Figure 5-1 Final Assembly A008569-01 A

Page 56

A ATARI’ tem rt Number

Qty.

Deseription 1A08576-01 75-9118 72-6812 73-1015 75-040 75-51328 75-048 n006647-02 908580-01 003573-01, 009345-01, 72-6816 3009341-01 {.008557-O1 75-9905058. (009992-01. st-unt (030005-01 n003270-01 487-01 75-55168 75-9355 75-045, 75-0158 906870-01 909343-01 007902-01 46 : 508233-01 A007197-01 A907734-01 70-2500),

T.v, Tray Assy “fee Figure 5-2 Ho-2a Wut, Hex Sevew, SM. #8 x 3/4 Lg., Phil Pan Hd. #10 Washer Plat 410 Washer, Split Lock Bolt, Carriage, $10-24 x 2.00 ta. Washer, Split-Lock, #8 Rear Door Assy W/Lcch Wood Sevew “6x 1 ) Plat Ha, Phil Power Switch{Harness Assembly Serew, S4., Pan d., Phil., #6 x 5/8"Lg. Rear Bezel ¥/sky Raider Graphics Monitor Yask Seam Cover Screw, $.M., #2 X 1-00" Lg., Phil., Pan Ha. Mirror/tave Assembly Mirror Tie-Down Panel Assy 8-20 nylon Lock Nuts On/O£E Switch Enclosure Self Test Chart Front Bezel, ¥/Sky Raider Graphics Flourescent Light Harness Board ~See a ly with Graph Coin Door Assembly-See Pique Bolt, Carciage, #4-20 x 1.00"L3, Black Rear Door Seal Ly Assenbly (B)-5ee Figure 5-6 Power Cord Assembly Screw Down Tie Wrap

Part Number Qty. DESCREPTION, 30 | acosaza-or 1 |] wain Harness 41 | A009262-02 1 || RP. shielé Box Assembly 42 | A030491-01 a |] pups Shield Pom Assembly-See Figur 5-7 43 | a909709-xx 1 |] pce Assembly/ (sky Raider)-Seu Figur: 4a | 72-6808 1 |] screw, SM., Pan., Phil-, #8 x 3" Lg. 4s | 72-6608 io |} Screw, SM., Pan.» Hae, Phil., #6 x 4" Lg. 46 | 001638-01 2 || Bracket panel wre 47 | 00667602 1 || Front Housing assembly “See Figure 5-9 48 | 82-8016 3 || screw, sutton Hd. Socket cap, 10-32 x 1.00" Lg. 49 | 75-99090006 2 || wet1 Nut, Blind Hole Fastener, 10-32 50 | acosa22-01 a {| Assy, Control Pane! -See Piguve 5-16 si | 75-5524n 6 || Bote carriage #4-20 x 1.50" La., Black s3 | mint 1 |} technical Manual 55 | 006305~01 1 |} Printed Poly Raq 56 | aoosea3-xx 1 |} Shipping céntainer Assembly 57 | 03024101 1 || vise cover sa | 72-6612 1 |] screw, $.8.P.H., Phil., #6 x 3/4 La. 59 | 009992-01 1 || on/oft Switch Enclosure

Final Assembly Parts Li: Figure 5-1

Page 57

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 58

Figure 5-2 TV Tray Assembly A008576-01 A NOTICE TO ALL FERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction forbidden without the specific written permission of Atari, inc. Sunnyvale California This arawing 1s only concitionally issued. and ‘either receipt nor possession thereof conters or iranslers fany right in, of heense to use. the subject maller of the Srawing oF any design OF techaical information shown tereon. nor any night #0 repreduce iis drawing or any part tmereo!, except for manufacture by vendors of ar incor porated ang for manulacture unser the corporation $ wet: lenlicense. norigh! lo reproduce is rawing is granted or the subject matter thereot unless by written agreement with oF written permission trom the corporation

Page 59

ATARI’ Figure 5-2 TV Tray Assembly Parts List

em

YOueune Part Number

A030575-02 008574-01 005594-01

72-6812

006319-03 Description

Assembly, Monitor Modification T.V. Tray Monitor Tie Down

Screws, S.M., B3elf-Tapping #8 x 3/4"

Copyright Decal (1978)

Page 60

50 REF (2 PLAces)

Figure 5-3 Light Assembly A030487-01 A NOTICE TO ALL PERSONS AECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the Specihic written permission of Alar. Inc. Sunnyvale Cattorma This drawing is only conditionally issued, and neither receipt nar passession tnereot confers or wransters any right in. oF license to use. the subject matter of the drawing or any design oF technical information shown thereon norany ght to reproduce this drawing or any part mereot except lor manulacture by vendors of Atari incor porated and for manutacture under the corporation Swit Tenlicense.no ght ta seproduce this drawing isgrantes or tne subject matter thereot uniess by writen agreement vain oF wrtten permission trom the corporation

Page 61

Figure 5-3 Light Assembly A030487-01

ATARI"

Item Part Number Description

1A008860-011Black Light Assembly 18"
2A005495-01118 Inch Fluorescent Light Assembly
3A030483-011Light Panel Assembly
472-68124#8 X 3/4" S.M. Screw
575-01084Washer Flat, #10
6A009270-011Fluorescent Light Harness
870-3061Fluorescent Tube 18" (F15 T8/BL)

© Awarner Communications Company

Page 62

Figure 5-4 Audio Amplifier Board A009574-01 A TRACES ARE ON OPPOSITE SIDE

Page 63

Figure 5-4 Audio Amplifier Board A009574-01 ATARI

ItemPart Number | Qty.Description
1009575-011 P.C. Board
210-51P01 Res, Carbon, 5%, 1/4W, 1 OhmR3
310-53901":""39"R6
411-52P71""" 1/2W, 2.7."R4
511-51211"=""120 ="R5
6 | 19-3161031 | Trimpot, 10K OhmR2
724-2501061 Cap, Electrolytic, 25V, l0ufcl2
824-2504771."“ 470ufc2
924-2501081"""— 1000ufcl
24-2502281""" 2200ufc5
27-2501031"Ceramic," .0lufC3
27-2501042... -lufCc4,11
31-MR75O2 Diode, MR75OCR1,2
31-1N40015. 1N4001CR8-12
37-TDA2002V1 Audio Amp, TDA2002VUL
69-004L Switch, SlideSw1
78-580051Connector, 10-Position
030184-C\1Heatsink
72-1604C3Screw, P.H., Phil, #6-32 x 1/4 lg , Cres

75-056 3 Washer, Lock, Int Star #6 78-16009 1 | Silpaa

10-51041 | Res, Carbon, 5%, aw, 100K OHMR12
Page 64
  • 2 pLcs

ames

ze

Ti ercs,

Figure 5-5 | Coin Door Assembly A006794-01 E NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden wilhout the Specific written permesion of Alati inc Sunnyvale: Cahtorna This drawing 1s only conditionally esusd_and neither reseipt nar possession therect canters or ransters| In of license to use the subject matter ot the Grawing oF any design oF technical mlormation showa Inereon nor any right o reproduce this drawing or any part thereot except for manutacture by vendors of Alani Meer porated and tor manutacture under the corporation 5 wri ten license no right to reproduce iisdrawingrs granted or the subject matter thereat unless by writien agreement ‘sith nr written permission trom the corporation TTT, TL Ltn

Page 65

Il AL ATARI’ Figure 5-5 Coin Door Assembly Parts List

ItemPart NumberQty.Description
1007637-011Front Bezel Assy. - Used only on -01 Coin Door Assy.

A007637-02 Ref.} Front Bezel Assy. - Used only on -02 Coin Door Assy. A007637-03 Ref.] Front Bezel Assy. - Used only on -03 Coin Door Assy. A007637-04 Ref.] Front Bezel Assy. - Used only on -04 Coin Door Assy.

007637-05Ref.|Front Bezel Assy. - Used only on -05 Coin Door Assy.

A007637-06 Ref.| Front Bezel Assy. - Used only on -06 Coin Door Assy. 4007637-07 Ref.| Front Bezel Assy. - Used only on -07 Coin Door Assy.

275-91654Nut 6°32
34007639-011Coin Lock~Out Assembly
4007640-012Coin Switch Assembly
5A002465-011Coin Counter Assembly
6004320-011Coin Door Weldment
7004341-012Secondary Coin Chute
8004344-011Key Loop
9004340-012Spring-Return
io004337-012Bracket, Wire Form
LL004338-011Lock: Out, Wire Form, R.H.
12004336-011Lock-Out, Wire Form, L.H.
13004326-01riButton, Scavenger
1475-0464Lock Washer, #6
15006904-012Spacer
16007359-01i,Lamp Socket
1770-11-471Lamp
1s73-30082Retaining "C" Ring, ‘Truare #5103-25
1975-99140016Self-Threading Nut, Tinnerman #SR18¢006
2075-026S4Washer #6
2175-00516LsKepnut, Style 842, St}., 6-32
22008629-012Spring
2371-21181Lock Assembly, Hudson Lock
2471-1225cU2Coin Mechanism for American Quarter only

71-125FB Ref.] Coin Mechanism for Belgian 5 Francs Only 71-121MG Ref.| Coin Mechanism for German Mark only 71-121KS Ref.| Coin Mechanism for Swedish Krona Only 71-12100YI Ref.] Coin Mechanism for Japanese 100 Yen Only 71-1210PE Ref.}] coin Mechanism for English 10 Pence Only 71-1220CA Ref.] Coin Mechanism for Australian 20-Cent Piece only

25007753-011Plate, Anti-Probe
26A007638-011Switch Assembly ~ Slam
27A006921-011Harness Assembly

© A Warner Communications Company

Page 66

NOTICE TO ALL PERSONS RECEIVING THIS DRAW

° © eoses Ceeeh

©

i ee Ceel oe

ay ~® 14)

Figure 5-6 Power Supply Assembly A007197-01 \ 4 REQD @

¢ ‘wo & (8) 8 REAP

fe)

Page 67

A ATARI’ Figure 5-6 Power Supply Assembly Parts List

| Item Part Number Qty. Description

1A009266-011Power Supply Base Weldment Assembly
2A006886-011Transformer Termination Assembly "Type B"
329-0531Cap., Sprague Electrolytic 26,000pf @ 15v
478-70501SC1Brkt., Cap. Mtg. Sprague #4586-48
5A006555-011P.C. Board Rectifier
779-44110045Fuse Holder, Panel Mounting
841-20031Filter, Power Line, 5 AMP
9A006958-C1A/RVolt Sel Block 95V
loA006958-02"Volt Sel Block 110V
112006958-03"Volt Sel Block 205V
12A006958-04"Volt Sel Block 220V
1378-27081Grommet ,Plastic
1472-1810S3Screw Pan Hd., #8-32 x 5/8"Lg.
1675~ 0489Washer, Split-Lock #8
1775-918S9Nut Hex #8
1875-01888Washer Flat #8
19A007192-011Power Switch Termination
20A007444-011Power In Harness
2146-2038011Fuse, 8 AMP, 125V, 3 AG Fast-Acting
2246-2012512Fuse, 2% AMP, 125vV, Slow-Acting
Page 68

CONN. ROW 1 ROW 2 PIN No, [MBUCTOM JUMPER [eAPAC toe cAPACTOR| A = —

< DB 3 x E H x J K uc M x N % ma P z Ss

Txx

fu x % Nv x

x 4 [Y¥

Zz t

3 x 4 x

Sx*LK
@xXx
7xx|
3xx
10XK1xX
itxix
2xx
i}xx
ioxx
iswx
Ioxx

ai

Figure 5-7 R. F. Shield Board A030491-01 A () AV VWs S30V74 1

ry oa ° a z Mow

bo i

vu z

a uv , g g zg £

BOsMAns WR HLA MEWACEL® ° 1 mow

( U

220000 9 xa B 8 3 z = = 8

>

o we o Mo oom ooo ox 0 oa 0 ow 0 ja—or 6 se 6 o @ 0 Ce) G8 ——s oor So 3 8 3 3 ca) N °

° £5 eS RA m

Lap 5 $3 2 23 3 ce z ind : Be ° en H ge , & : < i a |

fo}

°

NOTICE TO ALL PERSCNS RECEIVING THIS DRAWING. CONFIDENTIAL Reprodection tormidden without the specific watlen permission of Atar. Inc.. Sunnyvale, California. This avawing 1S onl; conditionally ‘ssued. and nevther 'eceipt nor possession thereof conters or transfers, any 1nght nf license To use. the subject matter of the ‘raming oF any design or technica) information shown thereon, norany right lo reproduce this drawing or any part thereol except far manulacture by vendors of Alar Incorporated ang for manulacture under ine corporation's writ ten license no ght to reproduce this drawing s granted of the subject matler thereo! unless By written agreement laiih'oF written permission from the Corporation

Page 69

A ATARI’ Figure 5-7 R. F. Shield Board A030491-01

Item Part Number 006549-01 79-517222 27-250104 27-A250104 41-3003 41-3004 52-003 52-004 009468-01 COOIDHKVe®WNe

© Warner Communications Company g

PweUPNP ARH a

GE Description

P.C. Board Connector, 44 Pin P.Cc. Mount Cap, Cer Disc, 0.luf, 25V Cap, Cer Disc, 0.luf, 25V (Small, Bottom Row) Inductor, 100uh Inductor, 100uh (Small, Bottom Row) Jumper, .60 Centers Jumper, .30 Centers Decal, R.F. Shield Label

Page 70

QNIMYHG SHH ONINI3D 34 SNOSH3d TIV OL JOON

iT WE Sap =,

NOs \— aw 33s

VERSION CHART Locaribn -01(# ROM: -02 (ROMA eer: Scene Tpeaear vac

03000% simi 1030603 MiNi NI a RI Di 030594 Efi 030585 “ANT 030599 Py

Figure 5-8 Sky Raider PCB Assembly A009709- xx A

Page 71

AN ATARI

Part Number 4 DESCRIPTION. ” 3s | a-s391 a |] Res, carbon 58, mx, 390 om R123, ao | 12s3a1 rfp ee aw 3300 riz4 a1 | 15-20aKar0 1 |] wixewouné, 108, 10m, 4 OM RE? a2 a 4a | 24-060227 2 || cap, etec, ov, 220ue ca 45 (24-250105, L i. " 25v, luf 92 ae | 24-250075 ra | carr aa a7 | 247250106 a ffs» doug cee 4a | 24-250226 ca | cess Hem | Part Number | Qty. Deseription a9 | 24-250107 1 eT less 1 | 009720-01 a [F.c. Board 50 | 24-250878 Fae | rd 39 2 | 10-5470 1 Res, Carbon, 5%, 4W, 47 OHM, R103 Fe i. 10-5121 2 % 5 ~ "1200" R114,117 al 4 10-5181 1 ” igo" ‘R26 53 5 10-5221 1 ™ 220 R58 kre é 1p 5271 i > Fo io 35 | 27-250102 3 » Disc, 28¥, 208, .00uF C46, 50,90 7 30-5331 2 “ 330" 58,9 36} 27-250472 z v8 TooaTue 645,48 8 10-5471 20 . * 470° R3,72-77,88-91,93- 57 | 27-280103 a “ Towe csi

tat se | 27-2508q3 co a a nS ad 9 10-5562 wo} » st S60 35-26, 42,49-53 se | 27-250198 cof] = eR ci3e,40,42,43, ao | 10-5601 rife “G80 Rio 47, 49,52-67, 69" ne | 1o-se2r af * 820 63,86, 109 78,8184 06,89, a2 | 1o-si0z 2 | » oe RL, 2/4-7.11,12,21, 91,92-96

(23,33, 34, 39-41, 43~ 60 27-25022¢ 2 * * * * # -22uf C79,88 48,54-57,108,111,12], Sod 125 62 | iene 1 eo mm 63 | 26201102 1 |] cap, mica, 1o0v, 38, r00pf 97 aq | 20-5182 4 som Tbe 759,64,69,116 6a | 2e-101e21 rfp ee” aaope ce7 15 | 10-sie2 af 8 em Lae * R70 6 16 10-5222 a *: "2.2K " R60,65,67,78,79,106| bat

113,115 67 a7 | 10-5272 4 soem ame 68,107,326 ,127 68 18 10-5332 1 ” “oN 33K" R22 ‘ 69 is | locese2 3 a 2 gin = Bei 66 yo | si-anar 4 || vices a2ar cre-11 20} 10-5472 2 soe 8 aK os 15/17 n | seavoia 4 || diode nora €R1, 2,45 21 10-5922 1 " " B2K " ‘R62 72 2 10-5103 qo so lox" R13,16,18,19, 82,83, 73 | a2-1w751a 1 || viode an7sia car

104, 105,212,119 74 | 32-1963 1 |] picae isgeae crs 23} ao-s223 5 ee R84 35 24 | 10-5473 2) nn aK pzoage 76 | 33-2364 2 || transistor 23606 04.5 3s | ap-si04 o ery or eae 17 | 34-2360 3. || transistor 2N3643 gu3

  • ioscise i]s ow . Rigs 78 | 34-2n6044 } || transistor 2néoaa & 27 10-5224 a * hy . R120 73 28 10-5334 a " “ ” R1lo 80 29 | 10-5074 | - * ery si | 37-74us00 4 || integrated ciresit 74us00 4,25 .D7,B9 30, 10-5105. 2 “ R30, 32 82 37-74LS02 1 ” “ 74LSO2 =? a2 10-5155 2 ” R27, 28 83 37~74804 1 " " 74504 ES 32 | 10-5395 a . ess aa | 37-74x804 2 ” 7ans04 3,83 33 10-5475 2 R29, 32 85 37-7406 2 = “ 7406 D6, P9 ba | 20-5106 phe 24,280,821 © A Won communicanara omoary

t PREPPPpre PrP?rrrprppd roger

-01 version Figure 5-8 Sky Raider PCB Assembly Parts List

Page 72

Part Number : Part Number DESCRIPTION e6 | 37-74808 1 || Integrated Cireuit 74508 140 | 90-102 1 |] crystal, 12.096 maz ¥1 0? | 37-742508 3 i “ 7a1s08 tay ee | 37-7409 a . 7409 12 os | 37-7414 2 ~ 7a4 a3 so | 37-74us1a 2 . yansia 144) 90-6010 1 |] wicroprocessor na 91 | 37-74L820 2 ” " 7aus20 145| 90-7019 2 RAM _2111A-4 F/#1,H/S1 92 | 37-741830 1 8 "754830 146 | 90-7002 1 || RAM, Mos 6810 FZ 93 | 37-741522 1 : 740832 uw? oa | 37-74usa2 5 : * tanse2 2A RS 148 a5 | 37-7574 1 : 74874 149 | 006559-01 a |} syne Prom ca 96 | 37-741876 4 " 7ans74 3 150 97 | 37-7a863n 2 * 7ause3a 98 | 37-74LS85 2 " 74Ls8s 030582-01 1 Prom, Trapezoid, LSB a6 99 | 37-7456 1 "741886 030583-01 1 Prom, Trapezoid, MSE BE 200} 37-742892 1 reuse 030884-01 a || Prom, Terrain, LsB 35 101 | 37-7sxs109 1 * —raxsi0s 930865-01 1 || Prom, Terrain, MSE xs 102] 37-7418253 1 7408153 020596-01 2 || Prom, missile, Msp PA 103 | 37-7438157 2 "7618157 930897-01 2 || exom, missize, 1sB 8 roa | 37-7axs161 16 “ Jansie2 030898-01 2 || bron 2 105 | 37-7418164 6 ‘7415164 7 Target EE ros | 37-74r8166 3 . “7418166 2 Target Er 107] 37-7418178 a : " 74usi74 I i nee Baa 10g} 37-741S175 2 a ba ‘VaLs175 030604-01 1 7800 PL 103 | 37-7415191 3 " “ 7qus192 030605-01 7000 RI _ no] a7-7an8195 2 . + 7ausi95 P ree] 03038 400 HY eine an | 377418257 3 . 7418257 379/K9,210 1e7| 030587-0 7400 am | g228 22 165] 030588-01 7800 Ll zeeg 13] 37-74s180 3 : > 7asi09 K2,L2,M2 tel pepsene 7506 Lig | BEES ala | 37-8928 2 : “ en2s 3/33, 170] 030590-0 7000 MINI) ZB ag nis | 37-6757 1 . * ers # in| 020591 400 mf gh 28 rie | 3714323 1 Regulator M323 172| 03089201 Prom, 7800 PL ages a7 | 37-nm324 z Integrated Circuit M324 BLO,E10 173} 090593-01 1 Prom, 7009 RI eras 1p | 37-1M33¢ 1 . "LM339 Fo 174 nis | 37-La556 2 : unsse 6 15 120 | 27-usee 2 : * uas6e 36.Ke ta | 37-coav6s 1 * coa0s6 Fe 125 | as-mvsors a |) te mvsons cr 127] 62-001 1 || switen, sesr, mom we] 66-Llerrr 1 || seitcn, sper, x6, ore 1 129 | 66-014P27 a |] seiecn, nex ore Kio 1a 132 | 72-2608 2 || serew, Pan Hd. PSL. 6-32 x 4 La, CRES a33| 75-016 2 || washer, Flac, 46 134| 75-086 2 |] washer, Lock, Int. Star, #6 135 | 7-916 2 |] Nut, Hex, 6-32, CRES 13678-16005 1 || stapes 15778-08001 1 J) meatsink 139] 79-4040 1 |] socket, 40 Pin, Med Insertion —B2

Page 73

A. ATARI Iten | Part Number DESCRIPTION

Fe ” i a & Ttem Part Number _| Qty. Deseription 49 | 2a-250107 1 losut C98 5 10-5221 1 " 220 Ron 33 | 27-250102 3 |] cap., cer. vise, 25v, 208, .001uf C46, 50,90 Be 6 10-5271 1 270 RZ sé | 27-250472 2 _ ¥ acai 0047uf C45,48 ta 7 10-5331, 2 ’ 330 R89 57 | 27-250103 1 ” "ms loluf 52 a? a 10-5471 20 ” 470 Bg, tact? aeva (oa sa | 27-250683 Fi « 4 oa ow “6BuE CBS g 7 9 10-5561 16 bl ‘ “560 R35-38,42,49-53 3 27-2501n4 il tue ao | 10-5661 a |e * 620 R10 5. 12 10-5102 29 . " 1K * R1,2,4-7,12,12,2i, 7 5 2 . « 4 - =

48,54-57, 108,111, 22: a2 >t te Zs 13 20-5122 2 . aoe Li 64 28-101821 1 " ” " " B20pE cay as 10-5182 1 . “18K R70 bd 2 1s | tors332 2 le : We ee yo | seater 4 || vicae arar cRe-11 2

  • An Setog > Bea! 73 32-IN7514 1 Diode 1N751A cRT
  • 1075223 ry) . bd 76 | 33-2N3644 2 || transistor 2n3644 94.5 a4 107583 ‘4 . a0 102 7 34-2N3643 2 by itor 2N3643 = 25 10-5104 2 “ R14,R85 8 34-2N6044 iA Transistor 2N6044 6 bo) 0-520 zfr 4 m0-3) 83 | 37-74s04 1 74804 5 aL 10-515! . 128 84 | 37-741804 2 74104 C3,R3 32 10-5395 3 a a5 37-7406 2 " " 7406 D6,Po 34 10-5106 3 " " 24,8046) © ire Conmoncaton Comeary
Page 74

aan 135, 138, 37- 74808 37-741808 37-7409 37-7414 37-740814 37-741820 37-7418 30 37-741832 37-740842 37-74874 37-7418 74 377408830 37-74L885 37-74L886 37740892 37-7418109 37-74L8153 37-7418157 37-74L8161 37-74LS164 37-745166 37-74,8174 37-7418175 37-7418191 37-74L8195 37-74,8257 37-748189 37-8728 37-8797 37-1M323 37-LM324, 37-1M3.39) 37-1MS56 37-1M566 37-€D4066 3e-MvS013 62-001 66-118PI7 66-014P27 72-1608C 75-016 75-056 75-916C 78-16005 78-06001 79-42040

DESCRIPTION Integrated Circuit 74508 " "741508 7409 7414 74Ls14 741820 751830 741832 74Ls42 74874 74874 74LS83A 74Lsas 74Ls86 74u892 7418109 7418153, 7ausis7 7418161 7418164 74,8166 7418174 7418175, 74Ls191 7418195 74u8257 743189 8728 " er97 Regulator LM323 Integrated Circuit LM324 é "M339 " 1Ms56 " LMs66 ” — cpaose Mvso13 Switch, SPST, MOM (sw2) Switch, SPST, x8, DIP (SW3) Switch, HEX DIP (Sw)

ro AL,BL, RO Alo D3,a9 R2,C8 Fa RE H3,33,K3,L4,85 Fa DS,C6,C7,D9 13,m3 B10,£10 Fo #6 J6/K6 ES Serew, Pan Hd. Phil. 6-32 x 4 Lg, CRES Washer, Flat, #6 Washer, Lock, Int. star, #6 Nut, Hex, 6-32, CRES Silpad Heatsink Socket, 40 Pin, Med Insertion

140 | 90-102 14. aaz 144 | 90-6010 145 | 90-7019 aac | 90-7002 149 | 006559-01 asi 152] 030582-01 153] 030583-01 154| 030s84-01 155| 030585-01 156 | 030596-01 157| 030597-01 158 | 030598-01 159 | 030599-01 el 16a an 174 | 030594-01 030595-01

DESCRIPTION, crystal, 12.096 MHZ Microprocessor RAM 2111A~4 RAM, MOS 6810 Sync Prom Prom, Trapezoid, LSB Prom, Trapezoid, MSB Prom, Terrain, LSB Prom, MsB Prom, Prom, Prom Rom, Target Mask Rom, 7800 Mask Rom, 7000

BR B/HL,H/SL F2 BG a8 KS Ma NS #2 M/NT

-02 version Figure 5-8 Sky Raider PCB Assembly Parts List

Page 75

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 76

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Hep

ITEMS 3 do 7 ARE FROTENED WITH ITEM 6G,

Figure 5-9 Front Housing Assembly A006676-02 A (

B)® 5 2EQ'D

5 REQ.

Page 77

AL ATARI’ Figure 5-9 Front Housing Assembly A006676-02

ItemPart NumberQty.Description
1006536-021Formed Front Housing (Black)
2009347-011Display Plex with Graphics
382-80165Screw, Button Hd. Socket Cap, 10-32 x 1.00" Lg.
475-990900065Well Nut, Blind Hole Fastener 10-32
50008692Grill, Speaker
673-7700414 Rivets, 3/16" 0.D. x .68" Lg. .250-.500 Grip
7A006675-012Speaker Assy
8006660-021Shield, Plex
9A007147-01LStarship Speaker Harness
1075-020S6Flat Washer, #10
VW75-970215Washer, Black, Nylon, #10

Tw] ‘A Warner Communications Company

Page 78

Jul pacr / TATED 160°

GN (TO BE SECURED IN

Figure 5-10 Control Panel Assembly A009822-01 A FNAL ASS‘)

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING. CONFIDENTIAL Reproduction

tnereon norany night tore produce ts draw onght to reproduce this araming granted 91 nereat unless by witten agreement vssian from the cormoratian

Page 79

Figure 5-10 Control Panel Assembly A009822-01 ATARI’

ItemPart NumberQty.Description
1009816-011Control Panel with Graphics
2008570-011Board, Control Panel Back-Up
3A005347-021Flight Control Assy
4001856-011Bushing, Aluminum
662-0021Led Switch
7A009818-011Control Panel Harness
872-68104Screw, SM. Pan Hd. Phil., #8 x 5/8" Lg.

© 4 warner Communications Company

Page 80

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the specitic written permission of Atari, Inc. Sunnyvale ‘nia This drawing 1s orly conditionally issued. a ner recent nor possesion inert contersor antes ubject matter of ine

thereo!, except for manulacture by vena porated and for manufacture under ne corporation s weit- Ten license, no right to reproduce this erawing s granted or the subject matter thereof unless by writien agreement with oF written permission from Ine corporation

m RTS] \¢ FA} VIEW.M DRECTION OF ARROW

Notes: D\ set EE SEES PE SER QUER TO ze th WED) RE. Ss8 a SEMEN

Figure 5-11 Flight Control Assembly A ores 4,5,19, 33, 34 Aee CaeeseD A005347-02 Jena, Ceey Sisey i (aes 518522, 33,34 ZIGRT Sipe)

Page 81

Figure 5-11 Flight Control Assembly A005347-02

ATARI’ g Description Ite: Part Number

1 004189-01 2 004190-01 3 A004194-01 4 78-40201 3 62-003 6 75-5524B 7 75~5532B 8 75-9158 9 75-045 10 005310-01 1 005308 12 A008997-01 13 005312-01 14 905313-01 1s 005334-01 16 72-5524N 17 72-6812 18 004202-02 19 005315~01 20 75-0148 21 18- 3001033, 22 7B 28C04 23 72-1806S 24 A009525-01 25 75-048 26 A009526-01

28 005333-01 29 19-026 30 7320812 31 005314-01 32 75-0288 33 A007257-01 34 75-4603 8 73-3001 See NBER EB EH ON EEE EEE

y PR ruHe

ROUEN ESN Cap Flight Control Base Flight Control Weldment Flight Control Handle Grip Switch Push button Bolt Carriage %-20 x 14Lg" Bolt Carriage %-20 x 2" Lg Nut, Hex (%=20) Washer, Lock (%) Retaining Pin Pot Mount Machined Spherical Ball and Bushing Assembly Rubber Stop Bracket, Bumper Plate, Backing Bolt, Hex Hd, (%-20 x ly Lg.) Screw, Sm., Pan Hd. (#8 x 3/4" Ly.) Handle Grip Bracket, Center Post Washer, Flat #% SPRING LEE FLe-o2u0"2 | SHRIM © TUBING, FIT-22) +e, Screw Pan Hd, (8-32 x 3/8 Lg) Linkage Asm Washer, Lock (#8) Hub Mount Asm

Hub Special Potentiometer Pin, Roll (1/8 Dia x 3/4 Lg.) Bracket, Pot Linkage Washer, Plat (#8) Firing Switch Harness Screw, Set (#6 x 3/16 Lg) Retaining "E" Ring (%" Shaft)

© Warner Communications Company

Page 82

Figure 5-12 Motorola Monitor Modification A030575-02 ATARI"

Part Number DESCRIPTION

190-0321T.V. Motorola 23" (M-700-155)
2030576-021Label, Modified Monitor (Motorola)
310-53321Resistor, 3.3K (4 W)
4A030822-011Assembly, Pot/Bracket
575-24062Screw, Mach. P.H.C.R. 4-40 3/8" Lg
675-041,2Washer, Split Lock #4
775-92452Nut, Mach., Hex #4-40
Page 83

Morey MotoRora MoOwOR AS FOLLOWS: FOP | POLE B.S 1K ReAstoOR (HEM 2) ON corer sire OF Fo. BORRD. DONE ENO Or THe Rea ine TO Junction OF ROA ANP REZ. Tie OER ENO OF Ee eto “iho GROUND. DAZ + UNZOWER VeRTickl YOKE CONNEZTION (Yeuo) wike) Fao FOE ROUND. 2OWeR THe yatou WIE Too + 72EN TAB. FOP Crferuny FeHove BELTROYTIC .\fTOR C40 FZOM PC BOARD ANP ReNZeR TT IT i THE Difbere MimEec TION. LRA + PNEN [oti es: prewery (eh 4) hes. BOKER “PMI WIRE PRO ITEM 4 TO Sunction Gower o108) DE OHO We Cdl. Tle 1 Nou THE + LAO Oe CALITO. CAD, SOLER 7 THIS LEAD ON THE BOYER Cre OF THE FC, EOkRD weg! ZONNELT FASION OF GREEN VIE FEOM TEM 4. Te GEOND. (TH sEOUP COMKTOR 16 NEAR +72) yeucw wire)

SBE MDUSTHENT PeOCEDOPE, sheeT Bora

NOTICE TO ALL PERSONS RECEWING THIS DRAWING CONFIDENTIAL Reo» Specitic written per Jehion forbidden without the jon of Atare inc Sunnyvale ‘Only congitionaly issued and le use, the subject matter of the Gravng ov any design o¢ lechaieal information shown thereon nor any nigh to reproduce this @rawinaa: any oar! thereat except for manutacture By venciors of Atari Incorporated and lor Manutacture idee the corporation s wit

Figure 5-12 Motorola Monitor Modification A030575-02 A

Page 84

Bear I, pare on a Pye, { . \ ait. rastefe. HEtanT 15" , ~ fn \ f a Tea? (7 3B

Niles fee O ver Veatéa aze To awe Rote Wala or 15". @® Aposvet VERTICAL wNeARITY ZonTROL AND READIYT ZIZeE CONTROL -lo Gwe THE Fo PORTIONS INDCATED ABOVE. BE ARE TO “SQuceze" GoTo oO PATER ao THAT TAL OF FANE |S ABOUT V2" FROM Bae. @_ SET AMUARy POSITIONING ZONTEOL (fend GE HD im ANAL PSSEMBLY, 256 ) THAT TOP oF Phere > WITHIN A WoNGE TAL PERSONS cv Ws orAAG Ye" OF THE MASK EDGE, :

Page 85

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 86

BEND TABS TO

“? PLCS

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

Figure 5-13. Pot Bracket Assembly A030822-01 A

Page 87

Figure 5-13 Pot Bracket Assembly Parts List

ATARI’

[ ttem Part Number Qty. Description

1030842-01alBracket, Pot Mount
279-131011Terminal Strip
316-52521Resistor, 2.5K (5w)
419-90371Potentiometer
5 A030841-01aEAssy., Monitor Mod Harness
67173-770011Pop Rivet .125 Dia.

Pp © warner Communications Company

Page 88

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 89

TV MONITOR SERVICING

INFORMATION

This chapter provides servicing information taken from the Motorola service manual. This manual has been reprinted by permission of the monitor manufacturer.

————— IMPORTANT NOTE The monitor in the Sky Raider game has been modified before being installed in the cabinet. For information on how this modification was performed, and for a list of parts used, see Figure 5-12 and Figure 5-13 in the previous chapter.

Page 90

M 5000-1 55 M7000-155

MOTOROLA Service Manual

CAUTION No work should be attempted on any exposed monitor chassis by anyone not familiar with servicing procedures and precautions.

A. GENERAL INFORMATION This manual contains information on the MS5000/M7000 monitor series and the +5 volt logic power supply. The M5000 uses a 19-inch CRT and the M7000 uses a 23-inch CRT. All CRTs are of the magnetic deflection type with integral implosion protection.

All monitor power supplies are capable of producing both +73 and +12 volts regulated from either 115-volt or 230-volt AC input to the transformer primary. Ali monitor variations described herein require a composite video input signal.

— SAFETY

CAUTION No work should be attempted on an exposed monitor chassis by anyone not familiar with servicing procedures and precautions.
  • Safety procedures should be developed by habit so that technicians rushed with repair work automatically take precautions.
  • A good practice, when working on any unit, is to first ground the chassis and to use only one hand when testing circuitry. This will avoid the possibility of carelessly putting one hand on chassis or ground and the other on an electrical connection which could cause a severe electrical shock.
  • Extreme care should be used in handling the picture tube as rough handling may cause it to implode due to atmospheric pressure (14.7 lbs. per sq. in.). Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Input and output connections for the monitors are made through a 12-pin connector plug located at the rear of the chassis. Inputs consist of composite video, audio, and 115/220 volt AC three-wire.

All monitors employ: four stages of video amplification, a two-stage sync separator, a two-stage vertical integrator, a four-stage horizontal sweep circuit, a three-stage vertical sweep circuit, a one-stage spot kill, a one stage blanking amplifier; and a regulated, full-wave bridge power supply.

Model Breakdown Chart F Modet Video Input 19" CRT 23” CRT| IM5000-155 Composite x

IM7000-155, Composite x

WARNING When handling, safety goggles and heavy gloves should be worn for protection. Discharge picture tube by shorting the anode connection to chassis ground (not cabinet or other mounting parts). When discharging, go from ground to anode or use a well-insulated piece of wire. When servicing or repairing the monitor, if the cathode ray tube is replaced by a type of tube other than that specified under the Motorola Part Number as original equipment in this Service Manual, then avoid prolonged exposure at close range to unshielded areas of the cathode ray tube. Possible danger of personal injury from unnecessary exposure to X-ray radiation may result.
  • An isolation transformer should always be used during the servicing of a unit whose chassis is connected to one side of the power line. Use a transformer of adequate power rating as this protects the serviceman from accidents resulting in personal injury from electrical shocks. It will also protect the chassis and its components from being

PART NO, 68P25253A47 & MOTOROLA Data Products _ carotstream, ILLinois 60187 COPYRIGHT 1977 BY MOTOROLA, INC. PRINTED INU.S.A.

Page 91

damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

  • Always replace protective devices, such as fishpaper, isolation resistors and capacitors and shields after working on the unit.
  • Before returning a serviced unit, the service technician must thoroughly test the unit to be certain that it is completely safe to operate without danger of electrical shock. Do not use a line isolation transformer when making this test. wa 10-0 MIVOLT (OR HIGHER) AC VOLTMETER, NOTES. 1. REPEAT EACH CHECK WITH THE LINE CORD.

REVERSED IN THE POWER OUTLET

  • METER READING MUST NOT EXCEED 7% VOLTS AC. HOT” LEAD OF METER TO EACH EXPOSED PART OF CABINET, AS WELL AS THE CABINET GROUND LEAD OF METER TO ANY EARTH -] GROUND SUCH AS A COLD WATER PIPE Ny

1S0%-OHM 10-WATT RESISTOR

Voltmeter Hook-up for Safety Check In addition to practicing the basic and fundamental electrical safety rules, the following test, which is related to the minimum safety requirements of the Underwriters Laboratories, should be pertormed by the service technician before any unit which has been serviced is installed in a game again.

A 1000-ohm-per-volt AC voltmeter is prepared by shunting it with a 1500-ohm, 10-watt resistor. The safety test is made by contacting one meter probe to any portion of the unit exposed to the operator such as the cabinet trim, hardware, controls, knobs, etc., while the other probe is held in contact with a good “earth” ground such as a cold water pipe.

The AC voltage indicated by the meter must not exceed 7% volts. A reading exceeding 7% volts indicates that a potentially dangerous leakage path exists between the exposed portion of the unit and earth ground. Such a unit represents a potentially serious shock hazard to the operator.

The above test should be repeated with the power plug reversed, when applicable.

Never reinstall a monitor which does not pass the safety test until the fault has been located and corrected.

Table 6-1 Motorola Monitor Electrical Specifications

MODEL MS5000-155 MODEL M7000-155

PICTURE TUBE

standard 19" measured diagonally (48.2 cm); 184 sq. inch viewing area (1188 sq. cm); 114° deflection angle; integral implosion protection; P4 phosphor 23” measured diagonally (58.4 cm); 282 sq. inch viewing area (1820 sq. cm); 110° deflection angle; integral implosion protection; P4 phosphor standard

POWER INPUT

FUSES M5000-155, M7000-155—0.8A,

+73 VOLT SUPPLY

VIDEO INPUT to 260 VAC 115/230 VAC, 110 Watts (nominal); 60 Hz provision for 230 VAC, 50 Hz

Electronically regulated over AC inputs from 103 VAC to 130 VAC, or 260 VAC

0.5 Volts to 2.5 Volts P/P maximum, composite for 50V at CRT

RESOLUTION 500 lines at picture center

LINEARITY Within 3%, measured with standard EIA ball chart and dot pattern

Page 92

Table 6-1 Motorola Monitor Electrical Specifications

HIGH VOLTAGE 17KV (nominal)

HORIZONTAL BLANKING INTERVAL 11 microseconds typical (includes retrace and delay)

SCANNING FREQUENCY Ld Horizontal: 15,750 Hz+500 Hz; Vertical: 50/60 Hz

ENVIRONMENT Operating temperature: 10°C to 55°C (ambient) Storage Temperature: —40°C to +65°C Operating Altitude: 10,000 ft. maximum (3048 meters) Designed to comply with applicable DHEW rules on X-Radiation CSA certified for use in coin-operated amusements in a combustible enclosure | UL listed under specification 1410 (electronic components) TYPICAL DIMENSIONS (35.8 x 46 x 37.6 cm) 14.11" H, 18.18" W, 14.83” D 16.72" H, 21.56” W, 16.18” D (42.4 x 54.7 x 41 cm)

Specifications subject to change without notice.

B. SERVICE NOTES

Circuit Tracing Component reference numbers are printed on the top and bottom of the three circuit cards to facilitate circuit tracing. In addition, control names are also shown and referenced on the schematic diagram in this manual.

Transistor elements are identified as follows: E—Emitter, B—Base, C—Collector.

Component Removal Removing components from an etched circuit card is facilitated by the fact that the circuitry (Copper foil) appears on one side of the circuit card only and the component leads are inserted straight through the holes and are not bent or crimped.

It is recommended that a solder extracting gun be used to aid in component removal. An iron with a temperature-controlled heating element would be desirable since it would reduce the possibility of damaging the circuit card foil due to over-heating.

The nozzle of the solder extracting gun is inserted directly over the component lead and when sufficiently heated, the solder is drawn away, leaving the lead free from the copper foil. This method is particularly suitable in removing multi-terminal components. CRT Replacement Use extreme care in handling the CRT, as rough handling may cause it to implode due to high vacuum pressure. Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Use goggles and heavy gloves for protection. In addition, be sure to disconnect the monitor from all external voltage sources.

  • Discharge CRT by shorting 2nd anode to ground; then remove the CRT socket, deflection yoke and 2nd anode lead.
  • Remove CRT from the front of the chassis by loosening and removing four screws, one in each corner of the CRT.

Adjustments A non-metallic tool is recommended when performing the following adjustments.

Regulator Adjustment

NOTE Misadjustment of the +73 volt regulator or the horizontal oscillator may result in damage to the horizontal output transistor or pulse-limiter diode. The following procedure is recommended to insure reliable operation.
Page 93
  • Connect the monitor to an AC line supply; then adjust supply to 120 volts (240 volts in some applications).
  • Apply test signal to proper input. Signal should be of same amplitude and sync rate as when monitor is in service.
  • Adjust HOR. SET coil L1 until display is stable.
  • Connect a DC digital voltmeter or equivalent precision voltmeter to the emitter of the regulator output transistor, Q17, or any +73 volt test point.
  • Adjust the 73V ADJUST. control, R93, for an output of +73 volts. Do not rotate the control through its entire range; damage to the monitor may result.
  • When adjustment is complete, the AC line supply can be varied between 103 and 130 volts AC to check for proper regulator operation. With the regulator operating properly, changes in display size should be negligible.

Horizontal Hold/Oscillator Adjustment Adjust the core of HOR. SET coil L1 until the horizontal blanking lines are vertical or the CRT display is stable (synced).

Vertical Height/Linearity Adjustment

  • Connect a test generator whose output is similar to the display signal normally used.

Motorola Monitor Circuit Board in Service Position Figure 6-1

  • Rotate the vertical size control, R60, until the smallest display is obtained.
  • Adjust the vertical linearity control, R64, until the top and bottom of the test pattern is equally spaced.
  • Readjust R60 untii the desired display height is obtained.
  • Readjust R64, if necessary, as in Step 2 above.

Focus Adjustment The best overall focus of the display is obtained by adjusting the focus control, R42, for best focus at a point which is near the center and approximately 1/3 down from the top of the display.

Monitor Servicing The monitor circuit board may be installed in a service position to provide easier access to the circuit foil when servicing the monitor (see Figure 6-1).

C. THEORY OF OPERATION Power Supply The power supplies are transformer-operated, full-wave, regulated supplies which maintain constant output voltages for input line variations of 103 volts AC to 130 volts AC, or 206 volts AC to 260 volts AC. Regulation of the output voltages is accomplished by using positive feedback through the integrated circuit reference amplifier.

+73 Volt Supply (See Figures 6-3,6-4) When the +73 volt supply attempts to increase, the voltage at pin 3 of IC1 will increase, while the voltage at pin 2 remains constant due to D20. The increasing voltage at pin 3 will cause the output voltage of the reference amplifier (pin 6) to increase the forward bias of Q19. The collector voltage of Q19, forward bias of Q18, and the base current of Q17 will all decrease. The resultant proportional increase of Q17 collector-to-emitter voltage will cancel the attempted output voltage increase.

When the +73 volt supply bus attempts to decrease; the voltage at pin 3 of ICI will decrease while the voltage at pin 2 remains constant. The decreasing voltage at pin 3 will cause the reference amplifier output voltage at pin 6 to decrease the forward bias of Q19. The collector voltage of Q19, the forward bias of Q18 and the base current of Q17 will increase. The collector-to-emitter voltage of Q17, which is in series

Page 94

COMPOSITE ‘VIDEO EMITTER vi0eo VIDEO AMPL 7 con FOLLOWER PREAMPL. we

WoO GmO 4 ' YOKE com VIDED CLAMP a

wonnoRi2|roRizoRwon, ||Pics
us/230 [ +-—recucaredotrvy fafcosc.ishDRIVERoureuTvoLTaGe

VOLTS ac POWER o+ av SUPPLY | INPUT

= ,

spor BLANKING

TERT VERT

syne:VERTventvent
seANeSonwrettconane|‘a0oniteaoth

Figure 6-2 Motorola Monitor Block Diagram

kag 150

Tow Qu? Agw REGULATOR

out$3PI

a poo

0.84.19,p

urn ~ pie s3 1g or

Fo ve -

Dak || Cae ae

Figure 6-3. +73 Volt Supply Circuit with the output, will decrease proportionally to the

attempted decrease in the outbut bus. NON”

PARABOLA FROM EMITTER

>

Resistor R84 shunts a portion of the output current around Q17 so less power is dissipated within 8 the device. Resistor R82 is the current-limiting resistor for Q18, and R86 controls the leakage current of Q17. Resistors R83 and R85 are the collector load for EXISTING VERTICAL SAWTOOTH WITHOUT VERT.PARABOLA ADDED

PARABOLA PULSE AND VERTICAL SAWTOOTH

A4Cc:ADDED TOGETHER,

Q19, and R88 and R87 provide an emitter voltage for ' NET EE PRODUGIIETHE Q19 within the range of IC1’s output voltage var- REQUIRED VERT. iations. Capacitor C45 filters high frequency var- DRIVING SIGNAL iations from the voltage at pin 7 of IC1, and C49 is a Miller-effect capacitor which eliminates instability. Figure 6-4 Motorola Monitor Vertical Drive Waveform

Page 95

+73V +190

Ql AGH EMITTER FOLLOWER

y CONTRAST |

T0033 Tek vigeo DRIVER ce cae zor oe viDeEo Taree | TO PINT fost + icaTHODED == a2 OF V1 ‘CRT) VIA R78

To 10 EMITTER 1012 COLLECTOR

Figure 6-5 Motorola Monitor Video Amplifiers and Output Circuit

Capacitor C32A filters horizontal frequency variations from the output bus.

Resistor R91 provides bias current for D20, and the value of R99 presents an impedance from pin 2 of IC1 to AC ground (through D20). Capacitor C46 couples high frequency voltage variations, which occur at the output bus, back to pin 3—preventing oscillations for proper operation of the reference amplifier. Resistors R92, R93, and R94 provide voltage division such that the adjustment of R93 can be set equal to the voltage of pin 2 of IC1. Resistor R95 provides bias current for D21 and also provides the +12 volt output. Diode D23 is necessary to temperature-compensate for variations within D21. Capacitor C328 filters AC variations from the output of the full-wave bridge.

Video Amplifiers and Output (See Figure 6-5) The compasite video signal is coupled to the emitter-follower Q1 through the input connector P1 and capacitor C1. Transistor Q1 is a buffer stage which matches the impedance of the signal source to the video preamplifer and the sync separator stages. Resistor Rt is a terminating resistor for the video signal source, and resistors R2, R3, R4, and RS form the biasing network for the stage. Capacitor C2 bypasses higher video frequencies to ground. The composite video signal is coupled from the emitter of Qi to the sync separator Q10 through C33 and to the contrast control R6 through C47.

The contrast control varies the amplitude and couples the composite video signal to the base of Q2 through capacitor C3. Transistors Q2 and Q3 are complimentary, direct-coupled, common emitter amplifiers. The voltage gain (approximately 12) of the preamplifier stage is controlled by the feedback arrangement of R9, R10, R11, and R12. Resistors R7 and R8 provide the base bias voltage for Q2. Capacitor C48 is used for high-frequency peaking.

The output of the video preamplifier stage is coupled to the video output stage through capacitor C4. Diode D2 clamps the video signal to approximately +0.7 volts (DC restoration) when a sync pulse turns on the sync amplifier Q11. The video output stage is connected in a cascade configuration. Transistor Q4 is a common emitter amplifier and Q5 is connected in a common base arrangement. Capacitors C7, C8, and resistor R16 are used for highfrequency compensation, and resistor R18 controls the gain of the stage to approximately 47. Diode D3 maintains the base of Q5 at +6.2 volts, while capacitor C5 filters the video signal variations from the base voltage. Resistor R13 provides a DC bias path for D2, and R19 and D4 are used to limit the current through the CRT.

Page 96

; 3 ae) erg , sas

a3agIO
200rt.
cr}C2R36
aaa15k |
001}D1]Baw‘to

Lo Ra7IC23 TO R20 jov0n 242K R34 10 cam 34 ww Q7 P2s

HORIZ DRIVER in HORIZ ORIVER 5

3.3K yew

+1

Figure 6-6 Motorola Monitor Horizontal Deflection Circuit

Capacitor C10 AC-couples the video from the collector of Q5 to the cathode of the CRT if D4 turns off due to high beam currents. Resistor R17 is the collector load for Q5, and R15 provides the bias current for the zener diode D3. Capacitors C9 and C6 filter video frequencies from the +150 volt and +12 volt supplies. Resistor R14 and zener diode D1 are used to supply +12 volts jor Q1, Q2, and Q3.

D. HORIZONTAL DEFLECTION CIRCUITS (See Figure 6-6) Phase Detector (See Figure 6-7) The phase detector consists of two diodes (D5 and D6) in a keyed clamp circuit. Two inputs are required to generate the required output, one from the horizontal sync amplifier, Q11, and one from the horizontal output circuit, Q9. The required output must be of the proper polarity and amplitude to correct phase differences between the input horizontal sync pulses and the horizontal time base.

The horizontal output (Q9) collector pulse is integrated into a sawtooth by R24 and C12. During horizontal sync time, diodes D5 and Dé conduct, which shorts C12 to ground. This effectively clamps the sawtooth on C12 to ground at sync time. If the horizontal time base is in phase with the sync (waveform A), the sync pulse will occur when the sawtooth is passing through its AC axis, and the net charge on C12 will be zero (waveform B). If the horizontal time base is lagging the sync, the sawtooth on C12 will be clamped to ground at a point negative from the AC axis. This will result in a positive DC charge on C12 (waveform C). The positive polarity causes the horizontal oscillator to speed up and correct the phase lag. Likewise, if the horizontal time base is leading the sync, the sawtooth on C12 will be clamped at a point positive from its AC axis. This results in a net negative charge on C12 which is the required polarity to slow the horizontal oscillator (waveform D).

Components R23, C15, R25 and C17 comprise the phase detector filter. The bandpass of this filter is chosen to provide correction of horizontal oscillator phase without ringing or hunting. Capacitor C13 times the phase detector for correct centering of the picture on the raster.

Horizontal Oscillator The horizontal oscillator employs the principles of the Hartley-type oscillator. Its operating frequency is sensitive to its DC base input voltage, thus permitting the frequency of the oscillator to be varied by the output voltage of the phase detector. The main frequency-determining components are L1, C19, and R28. The oscillator operates as a switch being biased alternately into saturation and cut-off. The initial forward starting bias is supplied via R26.

Horizontal Pulse Shaper and Driver The horizontal pulse shaper Q7 serves as a buffer stage between the horizontal oscillator and driver. Capacitor C20 and resistor R30 combine to shape the input waveform to the required duty cycle of 50%, which is necessary to drive the horizontal output stage.

Page 97

REFERENCE HORIZ, SYNC

OSC,ON FREQ NO CORRECTION VOLTAGE DEVELOPED

OSC,SLOWS, POS. CORRECTION VOLTAGE

OSC, FAST, NEG. CORRECTION VOLTAGE

Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms

The horizontal driver Q8 operates as a switch to driving horizontal output transistor Q9 through T1. Because of the low impedance drive and fast switching times, very little power is dissipated in Q8.

Resistor R35 and capacitor C21 provide damping to suppress ringing in the primary of T1 when Q8 goes into cut-off. Resistor R36 is used for limiting current in the collector of Q8, and C22 filters the horizontal frequency variations from the DC side of the transformer primary. Horizontal Output (See Figure 6-8)

The secondary of T1 provides the required low drive impedance for Q9. Resistor R37 limits currentin the base of Q9, while capacitor C23 provides additional reverse bias to keep Q9 turned off during the horizontal retrace pulse. Transistor Q9 operates as a switch which once each horizontal time period connects the supply voltage across the parallel combination of the horizontal deflection yoke and the primary of T2. The required sawtooth deflection current through the horizontal yoke is formed by the L-R time constant of the yoke and output transformer primary. The horizontal retrace pulse charges C27 through D8 to provide operating voltage for G2 of the CRT. Momentary transients at the collector of Q9, should they occur, are limited to the voltage on C27, since D8 will conduct if the collector voltage exceeds this value.

The damper diode D7 conducts during the period between retrace and turn-on of Q9 to reduce retrace overshoot; capacitor C28 is the retrace tuning capacitor. Capacitor C25 blocks DC from deflection yoke. Components R38 and C26 are damping components for the width and linearity coils. Capacitor 32D is charged through D10, developing the video output supply voltage.

a HORIZ LIN

= HoRIZSS & WiOTH® Lan HORIZ YOKE ML oer at Qs 7696 oy 7 30°F IZ OUTPUT 10 wat one baer won arr Ha RECT |

COLLECTOR | Ag To Pie HEATER VOLTAGE FOR V1 & 010 Coa DAMPER ].02 we | ~ 2

ce

2M 029) 0,47 = Dio Tes 4 = Ja ‘ADS = raz tocus fonsoy]" Have ys Es in cal 2nd ANODE

Tcl avs. 56K' Ras, 1) od nN i ‘a CAT Laos! Rewicae

Figure 6-8 Motorola Monitor Horizontal Output Circuit

Page 98

Trav 6.8K he 1M +1

Qqu3 aw Ab VERT. SYNC. AMPL,. 0.08 T0036

Figure 6-9 Motorola Monitor Sync Circuit Sync Circuits (See Figure 6-9)

The video signal is coupled from the emitter of Q1 to the base of Q10 through C33. The negativegoing sync tips turn on Q10 and are clamped to the value of the base voltage due to the base-emitter diode junction. The video information within the composite video signal, however, is less negative and Q10 remains off between each sync tip. Therefore, the waveform at the collector of Q10 will contain only the composite sync pulse information.

Resistors R45 and R46 provide base bias for Q11. The composite sync pulses are amplified and inverted by Q11 where they are coupled to the vertical sync integrator Q12, the horizontal phase detector, and the video clamp diode D2. Resistors R47, R48, and R49, are the collector load for Q11, and also provide base bias for Q12. Resistor R50 limits current through the base-emitter junction of Q12, and R51 is its collector load. Components R52, C34, R53, C35, and R54 form a double integrator which removes the horizontal pulses from the composite sync signal, leaving the vertical pulses to be amplified by Q13 and coupled to the vertical oscillator.

Vertical Oscillator and Output (See Figure 6-10) The vertical oscillator is a relaxation oscillator and operates at a free-running frequency that is set by

+12V +73V

RS6. Se1K

C36 10 Q13 COLLECTOR

RS7. 3.3K L4B VERT. YOKE

Figure 6-10 Motorola Monitor Vertical Oscillator Circuit

Page 99

the value of resistors R56 and R57. The series combination of C37 and C38 charges through D14, R61, and R60, until D12 turns on. This occurs when the anode voltage of D12 exceeds the gate voltage by approximately 1.0 volt. When D12 conducts, C37 and C38 are discharged to nearly zero volts; then D12 turns off and the cycle repeats. The value of R61 and the setting of R60 determines the amplitude of the waveform.

Diode D14 provides a small incremental voltage above ground to overcome the forward base-emitter drop of Q14; D13 provides temperature compensation for the output stage. Resistor R96 provides a constant oscillator load for variations in input impedance of Q14. Transistor Q14 is an emitter-follower used to transform the high impedance drive sawtooth to a low impedance drive for Q15.

The vertical choke L5 acts as a current source during linear scan time and provides a high-voltage pulse to aid retrace when Q15 shuts off. To limit this pulse to a safe value, a varistor, R66, is connected across the choke.

Since the impedance of the choke decreases when the collector current of Q15 increases, severe vertical non-linearity will result unless some compensation is employed.

Resistors R64 and R62 couple the emitter voltage of Q15 to the junction of C37 and C38. This path is resistive, and the waveform coupled back will be integrated by C38. This results in a pre-distortion of the drive sawtooth. This is done to compensate for the non-linear charging of C37, C38 and the changing impedance of C5. An additional feedback path through R63 and C39 serves to optimize the drive waveshape for best linearity. Capacitor C40 couples the signal to the vertical yoke winding and blocks DC.

Spot Kill (See Figure 6-11) The spot kill circuitry is used to reduce the effect of the electron beam concentrating on one area of the CRT after the monitor is turned off. The circuitry is accomplished by raising the arm of potentiometer R73 to the +150 volt level and, therefore, increasing the brightness to maximum to dissipate the highvoltage charge that normally remains in the CRT.

When the monitor is operating, transistor Q20 is on and its collector is near zero volts. Capacitor C44 charges through the base-emitter junction of Q20 and R97. Resistor R72 provides the base bias voltage required to keep Q20 on. When the monitor is turned R73 BRIGHTNESS 201V

CRT, PIN2

Figure 6-11 Motorola Monitor Spot Killer Circuit

off, the falling +73 volts is coupled to the base of Q20 to turn off the transistor causing its collector voltage to rise to approximately +150 volts. Diode D24 prevents the negative voltage swing at the base of Q20 from exceeding the reverse voltage rating of the transistor.

Blanking Amplifier (see Figure 6-12) The blanking amplifier combines both the vertical and horizontal retrace pulses to turn off the electron beam in the CRT once every horizontal line and once every vertical field. Capacitor C41 couples the vertical retrace pulses and capacitor C31 couples the horizontal retrace pulses to the blanking amplifier. Resistor R68 determines the amplitude of the vertical pulses, while R69 determines the amplitude of the horizontal pulses. Capacitor C42 bypasses R69 to couple the leading and trailing edges of the horizontal retrace pulses to the amplifier. Resistor R70 allows C41 to discharge when the retrace pulses swing below zero volts. Diode D15 prevents the retrace overshoot from exceeding the reverse voltage rating of Q20. Resistor R71 permits Q20 to turn off between retrace pulses, while R75 and R76 provide the collector voltage for Q20. Capacitor C43 couples the blanking pulses to the control grid of the CRT.

oa voc} oak

Motorola Monitor Blanking Amplifier Circuit Figure 6-12

Page 100

[__ RG (Contrast) ni} (HORIZ. OSC.) R73 12 Raz. (BRIGHT) (Focus) 12

Figure 6-13 Motorola Monitor Chassis Rear View —Component Location

Page 101

Figure 6-14 Motorola Monitor Circuit Board Detatl—Solder View 93

Page 102

POWER SUPPLY

Figure 6-15 Motorola Monitor Schematic Diagram

Page 103

P3 Na, +73V OUT. 05/06 (NOT

SHOWN) SHOWN)

(NOT

R64 Reo VERT. VERT. Di2) 013 LIN. 023 O18 1C1

vrsianzoe sw erence < ITSIOTSIAO'

Q6 T1 Q7 R73

BRIGHT

8 p04 020 Rb

P1 Q1 P5 CONTRAST

Figure 6-16 Motorola Monitor Circuit Board Detaii—Component Location

Page 104

Table 6-2 Motorola Replacement Part Numbers

REF.PARTREF.
NONUMBERDESCRIPTIONNO.NUMBERDESCRIPTION
Capacitors:318510191B98.01, 10%, 250V; Poly.
All values are in Microfarads unless otherwise noted.C3223S10255B7320/200, 400/125, 600/100,
a23$10255A2747, 50V; Lytic200/50; Lytic
oy21813566005, +80-20, Z5V, 50V;C338510191A51033, 10%, 160V; Poly.
Cer. Disc.C34,C358S10191A32—-.047, 10%, 250V; Poly.
C3,C4——-23S187A2622, 25V; LyticC3621$180E60.01, +80-20, Z5V, 50V;
cs21S180E60.01, +80-20; Z5V, 50V;Cer. Disc.
Cer. Disc.C37, 38,39 8S10191B670.22, 10%, 250V; Poly.
co218135660.05, +80-20, Z5V, 50V;c4023S10255A60100, 63V; Lytic
Cer. Disc.ora]8S10212B160.1, 20%, 400V; Mtlz.
C7218131625330pf, 10%, X5F, 500V;Poly.
Cer. Disc.C4221$180C820.33, 10%, N150, S00V;
cB21S180B87220pf, 10%, X5F, 500V;Cer. Disc.
Cer. Disc.C438S10191B67(0.22, 10%, 250V; Poly.
co8510191899.015, 10%, 250V; Poly.C4423510255B284.7, 100V; Lytic
c1085102128180.22, 10%, 400V;C458510191B90——-.033, 10%, 250V;; Poly.
Mtlz. Poly.C4621$132492.01, +80-20, Z5V, 100V;
cu218131625330pf, 10%, XSF, S00V;Cer. Disc.
Cer. Disc.c4a723S10255B63100, 10V; Lytic
c1221$180C41.0027, 10%, ZSF, 500V;C4821S180D5647pf, 10%, N750, 100V;

Cer. Disc. Cer. Disc.

C1321$180C0210pf, 10%, N150, 500V;cag218180B51.001, 10%, XSF, S00V;

Cer. Disc. Cer. Disc.

C1421S180D34.005, 20%, Z5F, 1KV;

Cer. Disc. Diodes:

C1523810229A32‘1.0, 16V; LyticD148510813A03Diode, Silicon, Zener;
C178510191B90.033, 10%, 250V; Poly.IN5242
C188510299B28——.01, 10%, 100V; Polycarb. | D248D67120A13_—Diode; A13
C198S10299B29.0082, 10%, 100V;D348510813A01Diode, Silicon, Zener;

Polycarb. IN5234B

208510191B98_.01, 10%, 250V; Poly.D448S191A02Rectifier, Silicon; 91A02
221S180B51.001, 10%, X5F, 500V;D5,D6 — 48D67120A11_—Diode; A11
Cer. Disc.D7485134921Diode, Damper; D1D
C228510191B98.01, 10%, 250V; Poly.D8&485134978Diode, Pulse Lim; D1K
323S10255B50150, 10V; LyticD1048S191A05Rectifier, Silicon; 91A05
C24215180B51.001, 10%, X5F, 500V;D1485137114Rectifier, H.V., D2Y
Cer. Disc.p12485137638Vert. Osc.; MPU6027
C258510299B270.82, 10%, 200V; Mtlz.D13,D14485191A05Rectifier, Silicon; 91A05
Polycarb.D1548D67120A11_Diode; A11
@e215131625faopt 18% XSF, 500V;bre. bie 485191405 _ Rectifier, Silicon; 91A05
C278510212A111.0, 10%, 630V; Mtlz.D2048S10813A02Diode, Silicon, Zener;

Poly. 1N5231B

C288510571A06.01, 5%, 1200V;D2148S10813A03Diode, Silicon, Zener;

Polyprop. Foil 1N5242

298510212B530.47, 10%, 630V; Mtlz.D2248D67120A11_Diode; A11
D23,D2448S191A05Rectifier, Silicon; 91A05

Poly.

Page 105

Table 6-2 Motorola Replacement Part Numbers

Re. ] Part No. | Description Ref. Part No. Description

Fuses:ROO18D25245A29Vert. Size; 250K
FI, F2655136269Fuse, 0.8A-250VR6418025245431Vert. Lin ; 100K
R666S10201A04Varistor, 1ma, 120V, 0.5
Integrated CireutissR7318D25245A28Control, Brightness; 200K
Ic51$10732A01Ref. Ampl.; T3FRad475135589150, 10%, 10W
R9318D25245A21Control, +73V out Adj.;

Coils/Chokes: 25K

u24C25448A01Coil, Horiz. Osc.Ros10731A031.3K, 10%, 5W
1224D25603A09Coil, Horiz. Width
1324D25248A14 — Coil, Horiz. Lin,Switches:
ad24025261409Coil, Defl.(M5000-155,swt40510624407Switch, Slide; D.P. D.T.

M5010-155)

“424D25261A10Coil, Defl. (M7000-155,Transformers:
M7010-155)Ti25D25221A05_Horiz.Driver
.25025221C12Choke; VerticalT224025240823H.V. Transformer
T325D25239B20Transformer, Power

Transistors: (M5010-155, M7010-155)

Qt465137171Emitter Follower, A6utB25025239830Transformer, Power
Q2485137172Video Pre-Ampl.; A6)(5000-155, M7000-155)
Q3488137127Video Pre-Ampl.; P2S
Q4485134952Video Driver; A2)Misc. Electrical Parts:
a5488137476Video Output; BEv196524140119"—-CRT; Type 19VARP4
Q6485137172Horiz. Osc.; A6}(M5000/M5010)
Q7488137127Horiz. Pulse Shaper; P25| yy96S10846A0123"-CRT; Type
Q8488137093Horiz. Driver; ASFM22VATP4 (M7000!
Q9485137570Horiz. Output; B2LM7010)
Qio485137173Sync Separator, P2W
qu488137172Sync Ampl.; A6)Mechanical Parts:
Q12488137172Vert. Sync Integrator; A6)9B25456A01Block, Fuse (F1, 2)
Q1348S137172Vert. Sync Ampl.; A6l42D25158C01Clamp, Defi. Coil
Qu485137639Vert. Driver; MPS A1326510251A08Heat Sink (Q3)
Qis485137596Vert. Output; B2VPI15810183469Housing, Connector;
Q16485137172Blanking Ampl.; A6JFemale (12-Contact,
Qi7485137368Regulator; ASWLess Contacts)
Q18485134952Reg. Driver; A2)39S10184A67Contact, Plug; 5 Req’d
Qi48S 137476Reg. Buffer; BIEM3000/M7000, 9 Req'd:
Q20485137476Spot Kill; BIEM5010/M7010
P215510183A82Housing, Connector;

Resistors Controls: Male (3-Contact, Less

NOTE: Only power or special resistors are listed. Use Contacts), M5000/M7000
the description when ordering standard values ofP215S10183A81Housing, Connector;

fixed resistors up to 2 watts. Female (3-Contact, Less

R618025245427Control, Contrast; 500Contacts), M5010/M7010
Ri4175135204100, 10%, 5W39S10184A67Contact, Plug; 3 Req’d
R1717S10731A013.9K, 5%, SWfor P2
R3617$10130B071.5K, 10%, 3WP3.28510586435Header, Connector;
R4218D25218A14_ — Control, Focus; 2M2-Contact
Page 106

Table 6-2 Motorola Replacement Part Numbers No. Wuumee DESCRIPTION ee Ee DESCRIPTION

P4, PS.15S10183B12Housing, Connector;14B25459A01Insulator, Fuse Cover

Female (3-Contact, Less (FA, 2)

Contacts) M5010/144562353Insulator, Mica (Q9,

M7010 Q15, Q17)

39510184484Contact, Plug; 3 ea.14C€25230A01 _— Insulator, Molded (On

Req'd for P5, M5010/ D11 Body)

M701014S10157A30Insulator, Nylon (2-
$215810183481Housing, Connector;Req'd.); Mtg. P.C. Board

Female (3-Contact, Less 14510550A02 _— Insulator, Transistor Contacts), M5000/M7000 Cover (Q9, Q15, Q17)

$215$10183A82 — Housing, Connector;35136050Screw, Tpg; 6-20x% CLU

Male (3-Contact, Less Pan (Mtg. Q9, Q15, QI7 Contacts), M5010/M7010 and D11 Socket)

39510184464 —- Contact, Receptacle;9D25470A01Socket, CRT; Incl’s.

3 Req'd. for $2 R77, R78, R79, R80

$315$10183A94Housing, Connector;9D25201A01Socket, H.V. and CRT

Female (2-Contact, Less Anode

Contacts) 9C63825A03 Socket, Power Transistor

39$10184A72Contact, Receptacle;Q9, Q15, Q17)

3 Req'd. for $3 41D65987A01 — Spring Special; CRT Aquadag Gnd.

Page 107

Cut along this line

TM-111 1st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name Firm CJ Distributor UO) Operator

Address UO Other City State Zip

Page 108

First Class Permit #1004 Sunnyvale, CA

Atari, Inc. P.O. Box 9027 Sunnyvale, California 94086

Attn.: Publications Group, Coin-Op Engineering

Second Fold

980%6 VO ‘aleahuuns 2206 XO ‘O'd “oul ‘WRI

a6p3 siy) ade,

Cut along this line

Page 109

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 110

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 111

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation Or improper testing.

In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.

EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may noi be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 112

@ ATARI’ ATARI INC 1265 BORREGAS AVENUE, RO. BOX 9027, SUNNYVALE, CALIFORNIA 94086 » TELEPHONE (408) 745-2000 + TELEX 35-7488

© 4 Warner Communications Company