CATHODE RAY TOMES

Kangaroo TM-204 2nd Printing

Kangaroo (Sun Electronics, 1982) · Technical Manual · 64 pages · 53 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

DISPLAY GAME SERIAL NUMBER LOCATION

Your game’s serial number is stamped on a label on the outside back of the game. The same number is also on the chassis of the video display, power supply, Regulator/Audio || Printed Circuit Board (PCB), and the Central Processing Unit (CPU) and Video PCBs. Please mention this number when calling your distributor for service.

CENTRAL PROCESSING UNIT (CPU) PCB

POWER SUPPLY GAME SERIAL NUMBER IDENTIFICATION TAG

VIDEO PCB

REGULATOR AUDIO II PCB

Page 3

Operation, Maintenance and Service Manual

Complete with Iilustrated Parts Lists

Manufactured under license from Sun Electronics Corporation

Page 4

Kangaroo™

© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

The Kangaroo™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the new Copyright Act of 1976.

This Act provides for increased penaities for violating federal copyright laws. Courts can impound intringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.

In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year.

Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anyone who purchases. such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Lithographed in the U.S.A. SL

Page 5

Kangaroo™

{ '

to licensed communications services is not permitted by the FCC (Federal Communications Commission) If you suspect interference from an ATARI game at your location, check the following: @ All grounds (green wires) in the game are properly connected as shown in the game wiring diagram, and @ The game's power cord is properly plugged into a grounded 3-wire outlet. If you are unable to solve the interference problem, please contact:

ATARI Customer Service (800) 526-3849 or (800) 538-1611

Notice Regarding Non-ATARI Parts

WARNING

Use of non-ATARI parts or modifications of your ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

The warranty printed on the inside back cover of this manual may be voided, if you do any of the following:

@ you substitute non-ATARI parts in your coin-operated game, or

@ you modify or alter any circuits in your ATARI game by using kits or parts not supplied by Atari.

Not only may the use of any non-ATARI parts void your warranty, but any such alteration may also adversely affect the safety of your game and may cause injury to you and your players.

Page 6

Kangaroo™

Table of Contents

Set -Up Procedures New Features .. 2.0.0... cece cect e ete etna 1-3 3 Game Inspection . 1-3 Cc. bathe Installation. 1-3 . Installation Requirements nage . 1:3 2 Voltage Selection ...... 6.6 cece etter eee eee 1-3 D. Switch Locations . . 1-4

  • On/Off Switch .. 1-4
  • Utility Panel Switches . - 1-4
  • Service Switch... 0.0... c cee ect eee eee eee 1-4
  • Option Switches .... 6.0.0... cece cece cette ene 1-4 E. Option Switch Settings . . . 15 F. Self-Test Procedure .. G. Game Play
  • Attract Mode
  • Ready-to-Play Mode .
  • PlayMode .......
  • High Score Mode ...
  • Hints for Game Play

Troubleshooting A. Comments on Troubleshooting 2-2 B. Self-Test Procedure ........... 22 B. Glossary of Schematic Signal Descriptions 2-4

Maintenance, Repair and Parts Cabinet-Mounted Assemblies The Controi Panel .......... Fluorescent Tube and Speaker Video Display CoinDoor........ Printed-Circuit Boards . . Power Supply Assembly onmoom>

Page 7

Kangaroo™

List of Illustrations

Figure 1-1 Game Overview, Upright Cabinet ....................00020e eee 1-2 Figure 12 Game Switch Locations ...... . 4 Figure 1-3 Self-Test Procedure .... se. 16 Figure 2-1 Self-Test Screen 1—Test PasseS............... ccc cece eee eee 22

Figure 2-2 Self-Test Screen 1—Test Fails... 2.2... 0... c ccc cece eee eee 2-3 Figure 2-3 Self-Test Screen2 ..... 2-3

Maintenance, Repair and Parts: Figure 3-1 Cabinet-Mounted Assemblies, Upright Cabinet.................. 3-2 Cabinet-Mounted Assemblies, Ireland-Built Cabinet . . 34 Figure 3-2 TheControl Panel ........ 0.0... c cece cece eee eee eee eee 3-7 Figure 3-3 Control PanelAssembly ........... 0.0 c cece cece eee e eens 3-8 Figure 3-4 8-Position Joystick Assembly... .... 2.6... c cece cece eee eee 3-10

Figure 3-5 Fluorescent Tube and Speaker, Upright Cabinet ................. 3-12 Fluorescent Tube and Speaker, Ireland-Built Cabinet ............. 314 Figure 3-6 Video Display............6. eee cece eee eee - 3-16 Figure 3-7 Vertically Mounted Coin Door... . 3-18 Figure 3-8 Printed-Circuit Board (PCB) Removal ..............-2000e0ee eae 3-21

Figure 3-9 Kangaroo Central Processing Unit PCB Assembly ............... 3-22 Figure 3-10 Kangaroo Video PCB Assembly . 3-26 Figure 3-11 Regulator/Audio ll PCB Assembly ..............0.000 eee eee 3-28 Figure 3-12 Power Supply Assembly ..............00 02 cece cece ence ees 3-30

Table 1-1 Option Switch Settings . : Table 1-2 Kangaroo Scoring .......6 0... e cece cece cnet ences

Page 8

Kangaroo™

If reading through this manual does not lead to solving a certain maintenance problem, cali TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Service only

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Facific Time) 5 From California, Alaska, or Hawaii © (408) 745-2900 ese Service from anywhere in the area shown in white €2 © toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) re From New Jersey © (201) 469-5993 From anywhere else in this area ‘toll-free (800) 526-3849

EUROPE Service only

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

@Z 06252155

vi

Page 9

Set-Up Procedures

How to Use This Manual

This manual, written for game operators and service technicians, describes the Kangaroo™ game.

The manual contains information about al/ Kangaroo cabinets. Whenever information is unique

to the Upright cabinet, this symbol appears: i Built cabinet, this symbol appears: he

Whenever information is unique to the Ireland-

Chapter One details new features, game set-up, option switch settings, self-test procedures, and game play.

Chapter Two includes troubleshooting procedures.

Chapter Three contains maintenance, repair, and parts information. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the game cabinet. {Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.

Chapter

Page 10

Set-Up Procedures . Kangaroo™

FLUORESCENT TUBE AND SPEAKER See Figure 3-5

COLOR VIDEO DISPLAY

aR) See Figure 3-6

&-POSITION JOYSTICK See Figure 3-4

CONTROL PANEL See Figures 3-2 & 3-3 ACCESS PANEL

CENTRAL PROCESSING FF UNIT (CPU) PCB See Figures 3-8 & 3-9 VIDEO PCB "4 See Figures 3-8 & 3-10

COIN DOOR > See Figure 3-7 ie = i; SERVICE SWITCH

REGULATOR/ AUDIO II PCB UTILITY PANEL e g pA See Figures 3-8 & 3-11

See Figure 1-2

POWER SUPPLY See Figure 3-12

WARNING SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded! POWER ON/OFF SWITCH ‘See Figure +-2

Figure 1-1 Game Overview

Page 11

Kangaroo™

A. New Features

The Kangaroo™ game has two new features. Even if you are familiar with ATARI® games, you should

note these important differences: @ Joystick Control. This new eight-position control is made of steel and molded plastic. It has few parts, which make servicing easier. The leaf switches snap in and out for easy replacement. The rubber bellows is designed for a quick return to center. @ Service Switch. There is a service switch located on the CPU PCB which allows you to enter credits without tripping the coin counter. New features and all other major parts in the game are illustrated in Figure 1-1. Throughout this manual, wherever one of these new features is mentioned, you will see this symbol:

B. Game Inspection

Please inspect your game carefully to insure that it was delivered to you in good condition.

NOTE Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door, inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the PCBs are firmly seated in their sockets. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the power cord for any cuts or dents in the insulation. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening. Set-Up Procedures
WARNING To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!

@ Note the game’s serial number. It is printed on a label on the back of the cabinet. Verify that the same serial number is also on the Kangaroo game PCBs, Regulator/Audio II PCB, power supply and video display. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check major subassemblies, such as the power supply, control panel and video display, for secure mounting.

C. Game Installation

  • Installation Requirements

Power 150W Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Upright Cabinet 64 x 79 cm (25% x 31 in.) 174 cm (68% in.) Ireland-Built Cabinet Space Required 64 x 79 cm (25% x 31 in.) Game Height 174 cm (68% in.) Space Required Game Height

  • Voltage Selection The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three different voltage selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color).

Before plugging in your game, check your line voltage. Then check the wire color on the voltage selection plug that is plugged into your power supply. Make sure the voltage selection plug is correct for your location’s line voltage (see Figure 3-12).

1-3

Page 12

Set-Up Procedures

D. Switch Locations

  • On/Off Switch The on/off switch is located on the back of the cabinet, lower left side (see Figure 1-2).
  • Utility Panel Switches The utility panel includes the volume control, selftest, coin switch, and coin counter(s). The coin switch is used to credit the game and it activates the left coin counter. These switches are located inside the upper coin door (see Figure 1-2). Kangaroo™
  • Service Switch The service switch is located on the CPU PCB. It is used to credit the game without activating the coin counter. It can also start self-test if it is pressed while powering on the game.
  • Option Switches Option switches are located on the CPU PCB in the upper right comer, to the right of IC42.

UTILITY PANEL:

COIN COUNTER

SELF-TEST

VOLUME CONTROL (TO increase, turn clockwise) GAME OPTION SWITCHES.

POWER ON/OFF SWITCH

Figure 1-2 Game Switch Locations

Page 13

Kangaroo™ Set-Up Procedures

E. Option Switch Settings

Table 1-1 details game option switch settings. Op- To verify option switch settings, power the game tions are preset at the factory and shown by the <@ off and then on again. Set the self-test switch to on symbols. However, you may change the settings to and verify the settings on the self-test screen. Then suit your individual needs. set the self-test switch to off.

Table 1-1 Option Switch Settings The table below contains the switch settings for options re- The coin mechanism(s) is a device on the inside of the coin door lating to number of Kangaroo lives, game difficulty, bonus and that inspects the coin to determine if the correct coin has been inprice options. The switches are on the CPU PCB to the right of serted. After this inspection, the mechanism either accepts the 1C42 and are accessible when the PCB is mounted in place. coin or rejects it.

Settings of 8-Toggle Switch on Kangaroo CPU PCB

  • OA
125678Option

Off 3 Kangaroo Lives <4 On 5 Kangaroo Lives Off Easy game difficulty < On Hard game difficulty

Off Off No Bonus Kangaroos

OnOffBonus Kangaroo at 10,000 points<
OffOnBonus Kangaroo at 10,000, 30,000 and every 30,000 thereafter
OnOnBonus Kangaroo at 20,000, 40,000 and every 40,000 thereafter

Left Coin Mechanism Right Coin Mechanism Games with one coin counter Games with two coin counters

OffOffOffOff1 coin for 1 credit1coin for 1 credit<
OnOffOffOff2 coins for 1 credit2 coins for 1 credit
OffOnOffOff2 coins for 1 credit4 coin for 3 credits
OnOnOff = Off1 coin for 1 credit1 coin for 2 credits
OffOffOnOff1 coin for 1 credit1 coin for 3 credits
OnOffOnOff1 coin for 1 credit1 coin for 4 credits
OffOnOnOff1 coin for 1 credit1 coin for 5 credits
OnOnOnOff1 coin for 1 credit1 coin for 6 credits
OffOffOffOn1 coin for 2 credits1 coin for 2 credits
OnOffOffOn1 coin for 2 credits1 coin for 4 credits
OffOnOffOn1 coin for 2 credits1 coin for 5 credits
OnOnOffOn1 coin for 2 credits1 coin for 10 credits
OffOffOnOn1 coin for 2 credits1 coin for 11 credits
OnOffOnOn1 coin for 2 credits1 coin for 12 credits
OffOnOnOn1 coin for 2 credits1 coin for 6 credits
OnOnOnOnFree playFree play

“4Manufacturer's recommended settings

Page 14

Set-Up Procedures

F. Self-Test Procedure

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary.

We suggest you perform the self-test procedure when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure.

Figure 1-3 Instruction Kangaroo™

Refer to Figure 1-2 for the location of the self-test switch and option switches. To perform the self-test, set the self-test switch to on or simultaneously power the game on and press the service switch. To end the self-test, set the self-test switch to off.

The complete self-test procedure is explained in Chapter 2, Self-Test Procedure. If a part of the test described in Figure 1-3 fails, refer to Chapter 2.

Self-Test Procedure

Test Passes

  • Set the seif-test switch to on (see Figure 1-2).
  • Observe the seven colored squares.
  • Activate all switches: control panel, coin and service.
  • Simultaneously press Player 1 and Player 2 start switches. The screen shows the self-test display. The ROMs and RAMs. are tested. If the screen is different from the self-test display, refer to Chapter 2, Se/f-Test Procedure.

Colors are blue, green, light blue, red, violet, yellow and white. If colors are not as described, refer to the raster-scan video display manual.

The 0 changes to 7 as the switch is activated. If test fails, refer to Chapfer 3, The Control Panel. Push the joystick diagonally up and to the left. For proper game operation, both the top and left switches must close at the same time, and the top and left 0s should each become 7. Push the joystick diagonally up and to the right, repeating the same procedure. Both the top and right switches should close, changing the corresponding 0s to 1s on the screen. if the test fails, refer to Chapter 3, 8-Position Joystick Assembly.

Game sounds are produced and increment automatically from SOUND 1 through SOUND J. If test fails, refer to Chapter 2, Self-Test Procedure.

Game sounds: SOUND 1 Game melody SOUND 2 Kangaroo jumping SOUND 3 Kangaroo punching SOUND 4 Kangaroo falling SOUND 5 Kangaroo dying SOUND 6 Apple falling SOUND 7 Kangaroo punching apple or gorilla SOUND 8 Bonus Kangaroo awarded SOUND 9 Begin new level SOUND A Monkey dying SOUND B_ Kangaroo getting fruit SOUND C_ End of level SOUND D Bell ringing SOUND E Monkey column decreasing by one monkey SOUND F Gorilla taking Kangaroo’s gloves SOUND G Kangaroo crouching SOUND H_ Apples falling from broken branch SOUND! Kangaroo climbing ladder SOUND J Kangaroo hopping

1-6

Page 15

Set-Up Procedures Kangaroo™

COCKTAIL ONLY PLAYER-2 JOYSTICK CONTROL UT. BLUE

COCKTAIL ONLY RED PLAYER-2 PUNCH

0 VIOLET

GREEN 0.» 9 YELLOW

BLUE 0

WHITE

COLOR ADJUSTMENT ———__ CHART

Ba EDGE DIP 12345678 3A 3B dA 8 converron SETTINGS” OPTION SWITCHES ——————" 0 90.10 0 0 0 1 0 1

—_—————— RIGHT COIN MECH t a vert COIN MECH SERVICE SWITCH ————> = Q

1-PLAYER START ————1 0

" 2PLAYER START —————> © 1+ O0\ 0 NN SOUNDS

NO. OF LIVES

GAME PRICING! GAME DIFFICUTLY CREDITS

JOYSTICK CONTROL = BONUS LIVES PUNCH

“These represent harness connections on the CPU PCB. 1 means the pin is shorted to ground in the harness. 0 means there is no connection in the harness.

Screen Pin on CPU

Shows Harness Connector 3A Cc 3B 3 4A D 8A Jd

NOTE: 8A is a zero if you enter self-test mode by pressing the service switch on the CPU PCB.

Figure 1-3 Self-Test Procedure, continued Self-Test Display

Page 16

Set-Up Procedures

G. Game Play

The Kangaroo™ game is a one- or two-player game with a color raster-scan video display. Game action takes place in the branches of a tree. The player controls a mother Kangaroo who must hop and leap from the bottom of the screen to the top to rescue her kidnapped baby. In her effort to get to her baby, the Kangaroo must punch out monkeys and avoid fruit that is thrown or dropped by the monkeys.

Kangaroo has five possible modes of operation: attract, ready-to-play, play, high-score and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter self-test at any time (all credits will be cancelled and the high score table will be erased).

  • Attract Mode

The attract mode begins when power is applied to the game, after a play or high-score mode, or after self-test. This mode is continuous and stops only when a Credit is entered, or when in self-test. In the attract mode, the screen displays one of three possible pictures.

The first picture shows ways to score points during game play. A mother Kangaroo hops across a top branch of the tree. She leaps to touch hanging fruit with her head and to ring a‘bell. When she touches the fruit, it disappears and a point value appears in its place. When she rings the bell, a new fruit appears where the old fruit was hanging. A monkey pursues the mother Kangaroo and she punches him. The monkey disappears, and a point value appears in his place. Meanwhile, the baby Kangaroo climbs down a ladder and goes to the mother Kangaroo. When they touch, the word MOM appears on the screen above the baby.

In addition to the game play simulation, PLAYER-1, LEVEL=1, PLAYER-2 and KANGAROO appear at the top of the screen. The high score appears in the center of the screen. Credits and © 1982 ATARI, INC. appear at the bottom of the screen.

1-8 Kangaroo™

The second picture shows the high-score table. The top ten scores and their matching initials appear on the screen. The words KANGAROO and IN- SERT COINS also appear.

The third picture simulates game play. Mother Kangaroo enters at the bottom of the screen. She hops across a tree branch and avoids fruit thrown or dropped by monkeys and punches out monkeys. She leaps to touch fruit with her head. She climbs a ladder to get to the next branch of the tree. In this way she hops, leaps and climbs to the top of the tree to rescue her baby. She rescues her baby, or in another simulated game, is destroyed by an apple thrown by a monkey.

In addition to game play, PLAYER-1, LEVEL =1, PLAYER-2, number of Kangaroo lives and bonus information appear at the top of the screen. The attract mode ends when coins are entered and accepted for game play.

  • Ready-To-Play Mode

During this mode the game level and score(s) for one or both players appear at the top of the screen. The words PUSH ONLY 1 PLAYER BUTTON appear when 1 credit is inserted. The words PUSH 1 OR 2 PLAYERS BUTTON appear when 2 or more credits are inserted. LET’S CHALLENGE also appears in the center of the screen. Credits appear in the bottom left corner of the screen. This mode ends when a player pushes the start button.

A picture appears briefly on the screen, showing three mother Kangaroos on three branches of the tree. The mother Kangaroo on the top branch falls through a gap to the bottom of the screen. The other Kangaroos join their babies, and the words MOM appear above their heads.

Page 17

Kangaroo™

  • Play Mode

In the Play Mode, the player controls the mother Kangaroo with an 8-position joystick. Thus, the player causes the Kangaroo to hop to the right or left, or to leap up to touch fruit, or to jump over apples thrown at her by monkeys. She may climb up ladders, or SUPER-LEAP diagonally to the left or right to climb up log-type stairs. The Kangaroo may also duck to avoid thrown apples, or hop down diagonally to the left or right to get down the log-type stairs.

Another player contro! is the PUNCH button. When pushed, it causes the Kangaroo to punch with her boxing glove. She may punch monkeys for 200 to 400 points. She may also punch fruit that is thrown or dropped by monkeys for 100 to 200 points. In addition, Big Ape may appear and try to take the Kangaroo’s gloves. Punching Big Ape is worth 800 points.

Game play progresses by levels. Each level has four rounds. Game play begins at Level 1. Bonus points appear at the top left of the screen. There are 2,000 bonus points at the beginning of each round, and the points decrease by 100 every five seconds. Remaining bonus points are awarded at the end of the round.

In Level 1, Round 1, mother Kangaroo is at the bottom of the screen on the branch of a tree. She must get to the top of ihe screen to rescue her kidnapped baby by hopping across tree branches and climbing up ladders to get to the next branch. The Kangaroo must avoid apples thrown or apple cores dropped by monkeys. She must punch out the monkeys that are in her way. For extra points, she touches strawberries by leaping to touch them with her head or by hopping on them. (If the Kangaroo tings the bell, new fruit appears in place of the strawberries.) Set-Up Procedures

The Kangaroo may also punch thrown or falling fruit for extra points. But if she is hit by fruit or touched by a monkey, she dies and a halo appears over her head. {f she hops, leaps and climbs to the top of the tree and gets to her baby, this round ends.

in Round 2 there are log stairs instead of ladders for the mother Kangaroo to climb. To get up the stairs, she must leap diagonally (GUPER-LEAP). The Kangaroo must be careful not to fall through any gaps in the stairs or on the branches, or she will die. Also, Big Ape may appear in this round. He takes the Kangaroo’s glove away from her by coming close to her and extending his arm. For about 10 seconds, the Kangaroo has to defend herself with a white flag. Then her glove reappears.

In Round 3 the baby Kangaroo is in a cage at the top of a column of monkeys. Mother Kangaroo may either punch out the monkeys one by one (for 400 points each), or climb up ladders to a branch of the tree where she can hop into the cage. The column increases by one monkey every 10 seconds. In addition, monkeys climb up a vine to get to a stack of 11 apples on a branch at the top of the screen. If the mother Kangaroo takes too long to get to her baby and a monkey gets to the apples, the branch breaks, and all the apples fall at one time.

In Round 4 there are ladders with missing rungs, stairs to climb, and gaps in the branches, making the rescue more difficult. If a player completes this round, Level 2, Round 1 begins. The player may punch the thrown fruit to score points. Play becomes more difficult as game play progresses. The game ends when all the Kangaroo’s lives are used up.

Page 18

Set-Up Procedures

  • High-Score Mode This mode begins when a player has one of the top ten scores. Letters of the alphabet are at the top of the screen, and the high score table is below the letters. A player enters his initials by using the joystick to guide a highlighted square to his initials. By pressing the PUNCH button, the initial is transferred onto a line between the alphabet and the high-score table. After the initials are entered, they are transferred into the table. To reset the high-score table, power the game off and then on, or enter and end the self-test mode.
  • Hints for Game Play

@ Ring the bell for extra points. New fruit with higher point value will appear in place of the old fruit. @ Avoid walking into a monkey. Punch monkeys for 200-400 points each. @ Do not let Big Ape take mother Kangaroo’s glove (it reappears after 10 seconds). @ Mother Kangaroo must duck, leap or punch to avoid being killed by thrown or dropped fruit. Kangaroo™

Table 1-2 Kangaroo Scoring

Kangaroo Punching Points Thrown Apples 100 Monkey Apple Cores Monkey from Column Big Ape

Kangaroo Jumping to Touch Fruit Points Strawberry 100 Tomato 200 Cherries 400 Pineapple 800 Completing Round 2000-100*

  • Decreases by 100 every 5 seconds
Page 19

Troubleshooting

This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you isolate the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is or isn’t working properly. The expanded self-test procedures in this chapter are included to help the qualified electronic technician determine why the game isn’t working properly.

Chapter

Page 20

A. Comments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II PCB, or the video display?

The next step is to check all harness wires and connectors to the suspected failing assembly. If you find no harness or connector problem, substitute an assembly known io be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly.

When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the display is failing, we suggest that a qualified video display technician handle the troubleshooting and repair. If the power supply or Regulator/Audio || PCB is failing, troubleshooting and repair are relatively simple, as these assemblies are not too complicated. If a game PCB is failing, troubleshooting and repair will greatly depend on your understanding of the operation of the PCB.

To effectively troubleshoot problems of a game PCB, it is necessary for you, the technician, to become familiar with the PCB’s hardware. The diagrams in the schematic package (included with the game) show the functions of the circuitry. Again, while troubleshooting the PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Kangaroo™

B. Self-Test Procedure

To enter Self-Test, set the self-test switch to the on position. The screen displays the picture below. See Chapter 1, Section F, Self-Test Procedure for a complete description of this picture.

NOTE This procedure does not test the coin door lockout coils. If the Self-Test passes, but the lockout coils do not energize when power is applied to the game, suspect the lockout coil wiring, coin door harness, game PCB hamess, or transistor TR3 (for the /refand-Built cabinet check TR3 and TR4) and related circuitry of the CPU PCB.

DIP 12345678 3A 2B dA ® coorcooo0 2 9 Ck

0.0 SOUND

Figure 2:1 Self-Test Screen 1 Test Passes

Page 21

Kangaroo™

van pons ROR ROM Ue

DIP 12345678 3A 3B dA 88 ooo10000 1 0 1 2

cic 0 0

Figure 2-2 Self-Test Screen 1 Test Fails

SCREEN 1: ROM FAILURE is indicated on the screen by the words ERROR ROM- and a number (for a ROM failure on the CPU PCB), or the words ERROR ROM V- and a number (for a failure on the Video PCB).

Note the indication of failure in Figure 2-2. The following lists the ROM chips and their locations.

Bad ROM Chip Location Screen Display CPU PCB ROM-0* IC7 ROM-1 Ics ROM-2 Icg ROM-3 1C10 ROM-4 IC16 ROM-5* IC17 ROM-8* 1024 ROM-12* 1C28 Video PCB ROM V-0 1C76 ROM V-1 1052 ROM V-2 'C77 ROM V-3 1053

  • Does not display on the screen if defective.

RAM FAILURE is indicated by a blank screen or by garbage displayed on the screen for a defective RAM at IC5 or IC6 on the CPU PCB. Make sure that ROM-0 and ROM-5 are good on the CPU PCB. In addition, inspect the dynamic RAM on the Video PCB Troubleshooting

at locations IC55-62, 66-73, 79-86 or 93-100. Troubleshoot using the game schematics and the CAT Box (using a Z80 interface) or a bus controller to locate the failing RAM.

SWITCH FAILURE is indicated by the proper 0 or 1 not changing on the screen when the switch is activated. Troubleshoot using the information in Chapter 3, Section B and game schematics.

SOUND FAILURE is indicated by no sound. Check the volume control levels on the utility panel and on the CPU PCB at VR2. Troubleshoot the following sound circuitry on the CPU PCB: G.I. sound chip at IC50, ROM 8 at IC24, Z80 Microprocessor at 1C34, RAMs at IC32 or 33, or audio amplifier at 1C61.

To go to screen 2, push the 1-player start and either PUNCH switch at the same time.

SCREEN 2:

A white crosshatch pattern with white dots centered in each square appears on the screen (see Figure 2-3). The corners of the red rectangle should be 14-inch in from the corners of the display bezel. The center part of each side of the red rectangle should be 14-inch behind the bezel, out of view. Use this pattern for convergence and white balance (see the raster-scan video display manual).

Figure 2-3 Self-Test Screen 2

Page 22

Troubleshooting Kangaroo™

C. Glossary of Schematic Signal Descriptions

CPU PCB Signals

NMI

WAIT

INT

o

cs2

RDI)

RD(H)

WR

xD

XY¥(H) VPOS

HPOS

BSEL

Wl EN PRI

INO

iNi

IN2

INS

ina

ouTO

ouTi

OUT2 Non-Maskable Interrupt

Wait

Interrupt Request (every 16 ms)

CPU Clock (2.5MHz)

Address Select (EBXX-EBXX)

Start Address of Data in Picture ROM for DMA Low Byte

High Byte

Low Byte Start Address in Bit Map RAM (Where Picture is High Byte Written) During DMA

Picture Size for DMA and DMA Start Low Byte

High Byte

Vertical Start Address in Bit Map

Horizontal Start Address in Bit Map

Dynamic RAM Bank Select Latch Set

A and B Bit Map Control Latch Set

Input Address Select ECOO (See Memory Map)

Input Address Select ED00 (See Memory Map)

input Address Select EE00 (See Memory Map)

Input Address Select EFOO (See Memory Map)

Input Address Select E400 (See Memory Map)

Output Address Select ECOO (See Memory Map)

Output Address Select EDOO (See Memory Map)

Output Address Select EE0O (See Memory Map) OUT3

HFEN

$D0-SD7

BDIR

BCi

1S0-IS3

0S0-0S3 Output Address Select EFOO (See Memory Map)

Set Color-Shading Latch

Sound Microprocessor Data Bus

GI AY-3-8910 Sound Chip Input/Output Select

GI AY-3-8910 Sound Chip Addres/Data Latch Select

MB8841 Custom Microcomputer Input Data Bus

MB8841 Custom Microcomputer Output Data Bus

Video PCB Signals KO

K1

k2

Kist

KOS1

XG

LD/SFT

WE

EXCT

EXCT

SEL Wil (A)

SEL Wil (B)

¢sc000

BSELO

BSEL 2

Ave’ Dynamic RAM Timing Signals (See Timing Diagram in Kangaroo Schematic Package)

DMA in Progress (Active High)

DMA in Progress (Active Low)

Flip Video Address (Dynamic RAM A)

Flip Video Address (Dynamic RAM B)

Character ROM Address Select

Bank Select Dynamic RAM A

Bank Select Dynamic RAM B

Horizontal Blanking (Active Low)

Page 23

Kangaroo™

TRGA

VSYNC

ARASO

ARASi

ACASO

ACAS1

AWEO

AWE1 Horizontal Sync

Vertical Sync

Dynamic RAM A* Color Shading/Red RAS

Dynamic RAM A Blue and Green RAS

Dynamic RAM A Color Shading/Red CAS

Dynamic RAM A Blue and Green CAS

Dynamic RAM A Color Shading/Red Write Enable

Dynamic RAM A Blue and Green Write Enable

Dynamic RAM B Color Shading/Red RAS

Dynamic RAM B Blue and Green RAS

  • NOTE: Dynamic RAM A refers to Playfield Bit Map; Dynamic RAM B refers to Motion Object Bit Map BCASO

BCAS1

BWEO

BWE1

AVAX0-13

AVBX0-13

ABPO-11

ABX0-13

DPZO-3

DPRO-3

DPGO-3

DPBO-3

DXZ0-3 Troubleshooting

Dynamic RAM B Color Shading/Red CAS

Dynamic RAM B Blue and Green CAS

Dynamic RAM B Color Shading/Red Write Enable

Dynamic RAM B Blue and Green Write Enable

Dynamic RAM A Video Address Dynamic RAM B Video Address

Picture ROM Address

Dynamic RAM Address from CPU and for DMA

DMA Color Shading Data from Picture ROM

DMA Red Data from Picture ROM

DMA Green Data from Picture ROM

DMA Blue Data from Picture ROM

Dynamic RAM Data Bus—Color Shading Data

Page 24

Troubleshooting

DXRO-3

DXGO0-3

DXBO-3

XXA0-6

XXBO-6

PRIA

PRIB

ENA Dynamic RAM Data Bus—Red Data

Dynamic RAM Data Bus—Green Data

Dynamic RAM Data Bus—Blue. Data

Dynamic RAM A Address Bus Dynamic RAM B Address Bus

Playfield Priority (Active Low)

Motion Object Priority (Active Low)

Playfield Video Output Enable (Active High)

Motion Object Video Output Enable (Active High)

Playfield Red Color Shading (Active Low)

Playfield Green Color Shading (Active Low)

Playfield Blue Color Shading (Active Low)

Motion Object Red Color Shading (Active Low)

Motion Object Green Color Shading (Active Low) BBHF

AR

AG

AB

AVR

AVG

AVB

BR

BG

BB

BVR

BVG

BVB Kangaroo™

Motion Object Blue Color Shading (Active Low)

Playfield Red Data

Playfield Green Data

Playfield Blue Data

Playfield Red Data AND Playfield Red Color Shading AND Playfield Priority

Playfield Green Data AND Playfield Green Color Shading AND Playfield Priority

Playfield Blue Data AND Playfield Blue Color Shading AND Playfield Priority

Motion Object Red Data

Motion Object Green Data

Motion Object Blue Data

Motion Oject Red Data AND Motion Object Red Color Shading AND Motion Object Priority

Motion Object Green Data AND Motion Object Green Color Shading AND Motion Object Priority

Motion Object Blue Data AND Motion Object Blue Color Shading AND Motion Object Priority

Page 25

Maintenance, Repair and Parts

This chapter details maintenance and repair information, and provides information for you to order parts for your Kangaroo game. Please note that common hardware has been deleted from most of the parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598thru approximately 190000-.

When ordering parts, please give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Atari Customer Service numbers are listed in the front of this manual for your convenience.

Chapter

Page 26

Maintenance, Repair and Parts Kangaroo™

A. Cabinet-Mounted Assemblies

Fluor. Light & Speaker— See Figure 3-5 036498-01 (Upper Retainer)

038420-01 (Attract. Glass)

003053-01 (Lower Retainer)

Video Display— See Figure 3-6

038419-01 (Shield)

178013-001 (Latch)

Coin Door Assy.— See Figure 3-7

A037491-01 (Coin Box)

038003-01 (Util. Panel)

A002465-01 (Coin Counter)

69-001 (Self-Test Sw.) ‘ 62.041 & (Coin Sw.)

19-9032 (Vol. Control) A038411-01 (Cabinet Assy.)

036495-01 (Grille)

78-6900402 (Tape)

Controt Panel Assy.— See Figures 3-2 & 3-3

Reg,/Audio il PCB Assy.— See Figures 3-8 & 3-11

A038004-01 (Util. Sw. Harn.)

A038453-01 (Power Harn. Assy.)

Power Supply Assy.— See Figure 3-12

178048-001 (Caster)

N\ 78-3201 (Glide) Schematics, Self-Test Label & Manuals— see parts list on following page

037332-01 (Grille) 178034-024 (T-Molding)

74-2110 (Lock)

037419-02 (Access Panel)

CPU PCB Assy.— See Figures 3-8 & 3-9

Video PCB Assy.— See Figures 38 & 3-10

A038578-01 (Main Harn. Assy.)

\ ‘A037470-01 A037453-03, (OniOft Sw.) ‘A037454-03 & ‘A037455-03 Gose92-01 (Power Cord) (OnlOtt Sw. Cover)

Figure 3-1 Cabinet-Mounted Assemblies Upright Cabinet A038410-01 A

Page 27

Kangaroo™ Maintenance, Repair and Parts

Figure 3-1 Cabinet-Mounted Assemblies, continued Upright Cabinet Parts List

Part No. Description A002465-01 6V Coin Counter

A037453-03Strain-Relief Power Cord(U.S.)
A037454-03Strain-Relief Power Cord(Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece,

Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)

A037455-03Strain-Relief Power Cord(Australia and New Zealand)

A037470-01 Power On/Off Switch and Mounting Plate Assembly A037491-01 Coin Box A038004-01 Utility-Switch Panel Harness Assembly

A038411-01Cabinet Assembly(includes legs and PCB retainers, but not the rear access panel)

A038578-01 Main Harness Assembly A038453-01 Power Harness Assembly The following four items are the technical information supplements to this game: ‘SP-204 Kangaroo™ Schematic Package ST-204-01 Kangaroo Label with Self-Test Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (Substitute TM-201 when using part no. 92-055, Wells-Gardner 19-Inch Display) TM-204 Kangaroo Operation, Maintenance and Service Manual 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Self-Test Switch

71-2110Lock Mechanism(for rear access panel)

78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x Inch Thick (72 in. required) 003053-01 Lower Attraction Glass Retainer 009992-01 On/Off Switch Cover 034536-01 Foam Vibration Damper (for Kangaroo game PCBs) 034536-02 Foam Vibration Damper (for RegulatorlAudio I! PCB) 036495-01 Speaker Grille 036498-01 Upper Attraction Glass Retainer 036686-01 Card of Game Pricing Labels (not shown in illustration)

037419-02Rear Access Panel(does not include lock)

037332-01 Ventilation Grille (located on cabinet top) 038003-01 Utility Switch Panel for Volume Control, Self-Test Switch, Coin Switch and Coin Counter

038419-01 Video Dispiay Shieid with Graphics 038420-01 Attraction Glass with Graphics 178013-001 Spring Draw Latch 178034-024 ¥a-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster 178070-001 Volume Control Knob

3-3

Page 28

Maintenance, Repair and Parts. Kangaroo™

Schematics, Self-Test Label & Manuals— see parts list on following page

038226-01 (Grille) 178034-024 (FMolding) 037332-01 (Grille) Fluor. Light & Speaker— see Figure 3-5

038439-01 (Shield) 03772102 (Access Panel) :

Video Dispiay—|a
see Figure 3-6a|meno
Sorq(Lock)
8-Positionbe0]
Joystick Assy.—72|
See Figure 3-4L\|78-6900402

ee \ (Tape) 178013-001 LB ] (Latch) - Control Panel Assy.— see Figures 3.2 & 3.3

cPU PCB Assy.— ‘ncas004.01 see Figures 38 & 3.9 (Util. Sw. Harn.) Coin Door Assy.— Video PCB Assy.— see Figure 3-7 see Figures 3-8 & 3-10

RegJAudio Il PCB Assy.— y = : see Figures 3-8 & 3-11 : 2

038003-017.Manteca

(Util. Sw. Brkt) ‘n0e4ss.01 (Main Harn. Assy.) A002465-01 (Power Harn. Assy.) (Coin Counter) 69-001 (Selest Sw.) 62.041 A037454.03 (Coin Sw.) (Power Cord) 19-9032 é (ol. Ctr) A037491-01 (Coin Box) a 78-3201 “ (Glide) Power Supply Assy.— 009992.01 ‘aedee 178048-001 1 see Figure 3-12 (Caster) (On/Off Sw. Cvr.) 803747001 (OniOft Sw.)

Figure 3-1 Cabinet-Mounted Assemblies, continued lreland-Built Cabinet A038430-01 B

Page 29

Kangaroo™ Maintenance, Repair and Parts

Figure 3-1 Cabinet-Mounted Assemblies, continued lreland-Built Cabinet Parts List

Part No. Description A002465-01 Coin Counter A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A037470-01 Power On/Off Switch and Mounting Plate Assembly A037491-01 Coin Box A038004-01 Harness for Volume Control/Self-Test Switch/Coin Counter Assembly

A038431-01Cabinet Assembly(includes glides and PCB retainers, but not the rear access panei)

A038452-01 Main Harness Assembly A038453-01 Power Harness Assembly The following four items are the technical information supplements to this game: SP-204 Kangaroo™ Schematic Package ST-204-01 Kangaroo Label! with Self-Test Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (Substitute TM-201 when using part no. 92-055, 19-Inch Wells Gardner Display) TM-204 Kangaroo Operation, Maintenance and Service Manual 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Self-Test Switch

71-2110Lock Mechanism(for rear access panel)

78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, ¥4-Inch Wide x %-Inch Thick 009992-01 On/Off Switch Cover 036686-01 Card of Game Pricing Labels (not shown in illustration)

037721-02Rear Access Panel(does not include lock)
037332-01Ventilation Grille(located on cabinet top)

038003-01 Utility Switch Bracket for Volume Control, Self-Test Switch, Coin Switch and Coin Counter 038226-01 Upper Cabinet Grille 038439-01 Video Display Shield with Graphics

038441-01Side Panel Decal(not shown in illustration)

178013-001 Spring Draw Latch 178034-024 %-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster

Page 30

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 31

Kangaroo™

B. The Control Panel A— WARNING

Prior to removing or repairing any switch on the control panel, unplug the game.

To Open the Control Panel:

  • Open the coin door. Reach up through the opening and release the spring-draw latches. They are on the cabinet side walls at each end of the control panel.
  • Lift up on the control panel at the top edge, and tilt it toward you. The control panel edge next to the display shield has foam tape applied to it. The tape cushions the shield and prevents liquids from entering the cabinet interior. Make sure this tape is in good condition.

Leaf Switch Repair: @ Adjust the leaf switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Don’t burnish the contacts. To clean them, use electrical contact cleaner. @ To replace a leaf switch, remove the screw with a Phillips-head screwdriver. @ To replace the switch button, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The ring on the outside of the control panel should not spin, due to its design. Maintenance, Repair and Parts

@ Reinstall the switch. Reconnect the harness wires as shown in the Schematic Package, Game Wiring Diagram. Make certain the right colors go to the right tabs ‘on the switch,

Start-Switch Replacement: These switches have a very low failure rate. If a switch should ever be suspect, first test it using the directions that follow,

To Test Switch: @ Remove the wires from the suspected switch. @ Attach the leads of an ohmmeter to normally open and common contacts. ® Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always remain closed or open, then replace the switch.

To Replace Switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires as shown.

SWITCH CONTACTS. START 1

BROWN NORMALLY OPEN CONTACT

BLACK ‘COMMON CONTACT

START 2

YELLOW NORMALLY OPEN CONTACT

BLACK ‘COMMON CONTACT

Figure 3-2 The Control Panel

3-7

Page 32

Maintenance, Repair and Parts Kangaroo™

! WARNING !

Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.

A038435-01 (Cont. Pni./Decal) 171021-001 8 Position Joystick Assy.— (Decal) see Figure 3-4 038224-01 (Cont. Pri.) rd 78-6900402 (Tape) 62.041 75-0108 (Start Sw.) (Fiat Washer)

75-040S. (Split-Lock Washer)

—&>. NN 036895-01 75-9118 ran (Hex Nut)

178030-003 75-9910NO (Pushotn. Assy. (Nut) 7551128 i (Carriage Bol) A038455-01 460013-001 A038415-01 (Hames) devon Hr) (Cont. Panev/Decai) 038418-04 (Decal)

038267-01 (Cont. Panel)

Figure 3-3 Control Panel Assembly Upright Cabinet A038414-01 A Ireland-Built Cabinet A038434-01 A

3-8

Page 33

Kangaroo™ Maintenance, Repair and Parts

Figure 3-3 Control Panel Assembly, continued Parts List

Part No. Description Upright Cabinet A038415-01 Control Panel with Decal 038267-01 Control Panel 038418-04 Control Panel Decal Ireland-Built Cabinet A038435-01 Control Panel with Decal 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, -Inch Wide x }4-Inch Thick (24 in. required) 038224-01 Control Panel 038438-04 Control Panel Decal For Upright and Ireland-Built Cabinets A038455-01 Control Pane! Harness Assembly 62-041 SPDT Momentary Pushbutton Start Switch 75-010S #10 Fiat Washer 75-040S, #10 Split-Lock Washer 75-5112B #10-24 x 34-Inch Black Carriage Bolt 75-9118 #10-24 Hex Nut 75-9910NO #%-11 Steel Stamped Nut 036895-01 Black Molded Switch Bezel 160013-001 Leaf Switch and Button Holder (Leaf switch only is part no. 160012-001) 171021-001 8-Position Joystick Assembly 178030-003 Black Pushbutton Assembly

Page 34

Kangaroo™

~S Maintenance, Repair and Parts

WARNING

Prior to removing or repairing the joystick, unplug the game. 99-080028 (Shaft)

99-080026 To Repair the Joystick: (Washer)

  • First remove the entire joystick assembly from the control panel (see Figure 3-3). Now locate the four screws in the plastic joystick frame and remove these screws.
  • Next remove the retaining ring from the bottom of the shaft. The assembly will come apart.
  • To replace the bellows, pry it up and out of the plastic frame. @ Reassemble in reverse order. ©® Note that the inner raised ring on the bellows is longer on one side. This side goes on the top of the assembly (toward the control knob).
  • To replace a leaf switch, you don’t need to disassemble the joystick. @ Using your thumbs, pry apart the plastic flanges on the switch holder. With your index finger, lift the 99-080036 (Top Plate)

99-080029 switch up So that it will clear the plastic tab located Wachs on the outside end of the switch holder. (Washer) @ Slide the switch out of its holder. Replace the switch in reverse order. Adjust the switch for a narrow gap.

99-080031 (Bellows)

99080025 Disassemble in the order indi- 99-080032 (Switch) cated. (Circled numbers match (Steel Washer) the numbered instructions.) T 99-080030 (Spring) ee } 4 99-080037 \ . S. (Sw Plate) a

99-080033 (Guard/Actuator)

1 99-080038 (Sw. Actuator) 82-AL616 (Screw) 1 ee a D> @ (Ring) Figure 3-4 8-Position Joysick Assembly 171021-001

3-10

Page 35

Kangaroo™ Maintenance, Repair and Parts

To Adjust the Joystick: ,

  • Make sure that each teaf switch is firmly seated in its 4 Pats ach Gatien hertle its ‘from the switch for holder. There is a small gray plastic tab on the outside easier servicing, end of the switch holder. The black plastic part of each @ Use a pair of needlenose pliers or a switch adjustleaf switch must be in front of this tab. ment tool to bend each double set of blades in to-
  • Check that all four leaf switches can be activated by ward the center. Make the bend where the double set watching the switch blades as you move the joystick of blades comes out of the black plastic part of the handle up, down, left and right. switch.
  • Test the four diagonal positions. In each diagonal posi- 5. Recheck the switch action. The switches must move intion, two leaf switches should close. Switches should dependently for right, left, up, down and diagonal mocontinue bending slightly after making contact. tion of the joystick.

LEFT: BLUE, BLACK JOYSTICK— TOP REAR VIEW

UP: WHITE/BLACK, BLACK DOWN: VIOLET, BLACK

RIGHT: GREY, BLACK

Figure 3-4 8-Position Joystick Assembly, continued

Parts List

Part No. Description

73-3003 Retaining Ring 82-AL616 #6 x 1-Inch Cross-Recessed Pan-Head Type BT Tapping Steel Screw 99-080025 Leaf Switch 99-080026 21nch Black Plastic Washer 99-080028 Metal Shaft 99-080029 Nylon Washer 99-080030 Spring 99-080031 Bellows 99-080032 Flat Steel Washer 99-080033 Plastic Guard/Actuator 99-080036 Top Plate 99-080037 Switch Mounting Plate 99-080038 Nylon Switch Actuator 171021-001 Joystick Assembly

3-11

Page 36

Maintenance, Repair and Parts Kangaroo™

C. Fluorescent Tube and Speaker

WARNING Before removing or repairing the speaker, fluorescent tube or fan, unplug the game. If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

Upright Cabinet i

To Replace Fluorescent Tube:

  • At the top front of the game, remove the three screws that secure the upper attraction-panel retainer to the cabinet. Loosen the three screws that secure the lower retainer to the cabinet. Lift the attraction panel up and out of its lower retainer.
  • Remove the cardboard locking tab at each end of the tube. Slightly rotate the tube up or down, and carefully remove it from the lampholders. Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the locking tabs. Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood board. If the tube is not grounded, it may not start.

To Replace Speaker: Remove the two Phillips-head screws that secure the light board to the cabinet. Slide the board out and unplug the 5-pin harness connector. Remove the board from the cabinet. Unplug the two plug-in connectors on the speaker. Remove the hardware that attaches the speaker to the board. Replace the speaker, and reinstall in reverse order.

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

Figure 3-5 Fluorescent Tube and Speaker

3412

Page 37

Kangaroo™ Maintenance, Repair and Parts

NOTE To ensure that the fluorescent tube starts, make sure the green ground wire is firmly attached to both the ballast transformer and the steel lamp bracket.

037469-01 (Bracket) 148001-001 (Speaker)

179035-001 (Lampholder)

A037457-01 79-561816P (Harness) (Wire Nut)

70-304 (Tube) 142028-xxx (Transformer) 9911003 (Starter) A037540-01 (Grd. Wire) 9911009 (Socket) 99-11006 (Tab)

Figure 3-5 Fluorescent Tube and Speaker, continued Upright Cabinet Assembly A037417-01 and -02 G Parts List

Part No. Description

A037457-01 Fluorescent Tube and Speaker Harness A037540-01 Ground Wire with Ring Lug 70-304 18-Inch 15W Cool White Fluorescent Tube 79-561816P_ Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Lamp Starter 99-11006 Fluorescent Lamp Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037469-01 Steel Lamp Bracket 142028-001 60 Hz 118V Ballast Transformer (used on A037417-01 assembly) 142028-002 50 Hz 118V Ballast Transformer (used on A037417-02 assembly) 148001-001 6x 9-Inch 4-Ohm 15W Oval High-Fidelity Speaker 179035-001 2-Pin Fluorescent Lampholder

3-13

Page 38

Maintenance, Repair and Parts

WARNING Prior to removing or repairing the speaker, fluorescent tube or fan, unplug the game. If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

lreland-Built Cabinet * To Remove the Tube and Speaker Board: 1. From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker's 5-pin harness connector. Open the control panel (see Figure 3-2, The Control Panel). From the top front of the game, remove the five button-head screws that secure the upper cabinet grille to the cabinet. Lift the grille up and away from the cabinet. Be careful that the glass display shield doesn’t fall forward. Lift the video display shield up and out of the cabinet. Slide the baffle board that is below the fluorescent tube out through the front of the cabinet. Kangaroo™

  • Remove the screws that secure the tube and speaker board to the cabinet. Slide this board up and out of the cabinet.

To Replace Fluorescent Tube:

  • Remove the Y-lead connectors at each end of the fluorescent tube.
  • Slightly rotate the tube up or down, and carefully re- Move it from its clamps. Replace it with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the Y-lead connectors. Reinstall the light and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the control panel and the rear access panel.

To Replace The Speaker:

  • Unplug the two plug-in connectors on the back of the speaker.
  • Remove the hardware that attaches the speaker to the board. Replace the speaker and reinstall the hardware and two plug-in connectors. Reinstall the light and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the control panel and the rear access panel.

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

3-14 \ 038226-01 (Grille)

038217-01 (Baffle Board)

03843901 (Shield)

Figure 3-5 Fluorescent Tube and Speaker, continued

Page 39

Kangaroo™ Maintenance, Repair and Parts

Disassemble in the order indica- 038151-01 ted. (Circled numbers match the (Jmpr. Wire) numbered instructions.)

99-11012 (Clamp)

038219-03 (Light & Spkr. Bd.)

99-11009 (Socket)

99-11003 (Starter)

142028-002 (Transformer)

  • 035835-01 (Connector)

148001-001 (Speaker)

(Harness)

NOTE To ensure that the fluorescent tube starts, make sure the ground wire is firmly attached to the transformer.

Figure 3-5 Fluorescent Tube and Speaker, continued lreland-Built Cabinet Assembly A038228-01 A Parts List

Part No. Description

A038228-01 Fluorescent Tube and Speaker Assembly A038253-01 Light and Speaker Harness Assembly 70-303* 18-Inch, 1-Inch Diameter, 15W Cool White Fluorescent Tube 99-11003 Fluorescent Lamp Starter 99-11009 Starter Socket 99-11012"* 1% -Inch Fluorescent Tube Clamp 035835-01 12-Inch Y-Lead Connector 038151-01 Jumper Wire 038217-01 Baffle Board 038219-03 Light and Speaker Board 038226-01 Cabinet Grille 038439-01 Display Shield 142028-002 50 Hz 118V Ballast Transformer 148001-001 6x@-Inch 4-Ohm 15W Oval High-Fidelity Speaker

  • Acceptable substitutes are part numbers 70-304 (tube) and 99-11011 (clamp). They must be used together.

3-15

Page 40

Maintenance, Repair and Parts Kangaroo™

D. Video Display To Remove Video Display:

1, Open the rear access panel. Unpiug the three display

WARNING harness connectors and disconnect the green ground Shock Hazard wire. The following procedure should only be per- 2. Remove the hardware that secures the rear of the Upformed by a qualified service technician. Prior right cabinet display chassis to a wood cleat. Remove to removing or repairing the video display, unthe hardware that secures the /reland-Built cabinet displug the game. As an extra precaution, we play chassis to a metal bracket. highly recommend you discharge the high volt- ic z age from the picture tube. 3. Open the control panel (see Figure 3-2). For the Ireland- Built cabinet, remove the 5 button-head screws that se- High voltages may exist in any video display, cure the upper cabinet grille to the cabinet (see Figure even with power disconnected. Use extreme 3-5). Lift the grille up and away from the cabinet.
caution and do not touch electrical parts of the i ji, . display yoke area with your hands or with met- 4. Lift the video display shield up and out of the cabinet. al objects in your hands! 5. Carefully remove the cardboard bezel. Implosion Hazard 6. Remove the four sets of hardware that secure thefront If you drop the display and the picture tube of the display chassis to the wood frame. breaks, it will implode! Shattered glass and the 7. Carefully pull the display out through the front of the yoke can fly 6 feet or more from the implosion. cabinet. Place the display on a padded table in a pro- Use care when replacing any display. tected area so that nothing can hit it or fall on it. After servicing the display, reinstall in reverse order.

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

038226-01 (Grille)

(Shield) i

92.049 037443-01 ; rach Gs) ‘Bezel i @) «video Dispiay) 037750-01 03823201 (Bracket) (Bezel)

Figure 3-6 Video Display

3-16

Page 41

Kangaroo™ Maintenance, Repair and Parts

Figure 3-6 Video Display, continued Parts List

Part No. Description

Upright Cabinet 92-049 19-Inch Electrohome Color Raster-Scan Video Display (Acceptable substitute is part no. 92-055—use with TM-201) 037443-01 Display Bezel 038419-01 Display Shield with Graphics Ireland-Built Cabinet 92-049 19-Inch Electrohome Color Raster-Scan Video Display (Acceptable substitute is part no. 92-055—use with TM-201) 037750-01 Display Mounting Bracket 038439-01 Display Shield with Graphics 038226-01 Upper Cabinet Grille 038232-01 Display Bezel

3417

Page 42

Maintenance, Repair and Parts Kangaroo™

:

E. Coin Door

470000-001 (Lamp) 99-5023 179047-001 (Base Plate) (Lamp Base) by

  • 99-15040 9.15026 pines 99-15056 (Coin inlet)

(Screw for Bezel 4

99-1502 ——», / (Coin Inlet)

PART OF 99-15069 Ky 5055 9915054 a ct! 99-15068 s piv ot for L (Retng ae \. (uockout Coil) t ( Lever) 99-15069 (Lockt. Coil Spring)

9.15027 (Coin Ret. Box)

L 90-15028 come, (Coin Ret. Box)

(hone Wash.) 99-15037 (Sw. Adjuster) 9.15056 (Screw for Bezel) 9.15029 99-15060 (Bracket)

(Switch)

(Screw)

a (Sw. Cover)

7244148 (Screw)

Figure 3-7 Vertically Mounted Coin Door A037619-xx C

3-18

Page 43

Kangaroo™

99-15063 (Screw) SN

99-15067 (Lock Assy.)

A037491-01 (Coin Box)

A037542-01 (Harness—not shown)

A037619-01 — U.S. 25¢/25¢ Coin Door ‘A037619-02 — U.S. 50¢/50¢ Coin Door A037619-03 — Canadian 25¢/25¢ Coin Door 4037619-04 — British 10 P/10 P Coin Door ‘A037619-05 — British 10 P/50 P Coin Door A037619-06 — British 20 P/50 P Coin Door ‘A037619-07 — Australian 20¢/20¢ Coin Door 99-15067 (Lock Assy.)

‘A037619-08 — German 1 DM/1 DM Coin Door ‘A037619.09 — German 2 DM/1 DM Goin Door A037619-10 — German 2 DM/5 DM Coin Door ‘A037619-11 — German 1 DM/5 DM Coin Door A037619-12 — 5 Fri5 Fr Coin Door A037619-13 — Swiss 1 Fri1 Fr Coin Door A037619-14 — French 1 Fri1 Fr Coin Door Maintenance, Repair and Parts

99-15038 (Bezel for Button)

99-15001 thru 99-15011 (Ret. Button)

99-15071 (Clamp)

99-15066 (Screw)

9915074 (Lower Door)

A037619-15 — French 2 Fri1 Fr Coin Door A037619-16 — Swedish 1 Kr/1 Kr Coin Door ‘A037619-17 — Spanish 25 Pts/25 Pts Coin Door A037619-18 — Italian 100 L/100 L Coin Door A037619-19 — Hong Kong $1/$1 Coin Door A037619-20 — Japanese 100Y/100Y Coin Door

Figure 3-7 Vertically Mounted Coin Door, continued A037619-xx C

3-19

Page 44

Maintenance, Repair and Parts Kangaroo™

Figure 3-7 Vertically Mounted Coin Door,continued Parts List

Part No. Description A037491-01 Coin Box (Not included in assembly) A037542-01 Harness Assembly 171006-035 Metal Coin Mechanism 72-1405S #4-40 x %.Inch Cross-Recessed Pan-Head Steel Machine Screw 72-1414S #4-40 x %,-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9145 #4-40 Steel Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S, 25¢) 99-15036 Metal Coin Return Cover 99-15037 Switch Adjuster 99-15038, Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055, Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15068 Lockout Coil 99-15069 Spring for Lockout Coil 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 170000-001 6.3V Miniature Wedge Base Incandescent Lamp 179047-001 Lamp Base

3-20

Page 45

Kangaroo™

F. Printed-Circuit Boards

WARNING

Prior to removing or repairing any printed-circuit board, unplug the game.

To Remove Printed-Circuit Boards:

  • Open the rear access panel.
  • For the game PCBs, unplug the edge connectors. Remove the wood screws that attach the top cleat to the game cabinet, and remove this cleat. The sides of the video PCB are secured by plastic retainers. To release this PCB from the retainers, gently pry the retainers away from the PCB.
  • Carefully remove the PCBs from the slots in the bottom cleat. Be careful not to twist the boards, as this may loosen connections or components. Repair as required. @ Reinstall the game PCBs, making sure they fit securely into the slots of the bottom cleat. Maintenance, Repair and Parts

@ Gently pry the plastic retainers back and secure the video PCB in these retainers. To insure that the game PCBs will not be damaged when you move the game, be sure to reinstall the top cleat. |. For the Regulator/Audio 1) PCB, disconnect the four small harness connectors on this board. . Remove the screw and two spacers that secure this board to the cabinet and carefully remove the board from its slot. Be careful not to twist the board, as this may loosen connections or components. Repair as required and reinstall the board. Make sure that the connectors on the game or Regulator/Audio Il PCBs are properly plugged in. Note that they are keyed to fit only one way, so if they don’t slip on easily, don’t force them. A reversed connector will probably damage your game and void the warranty. Close and lock the rear access panel. Check that the operation of the game is correct by performing the self-test. This is very important when you repair a PCB.

038423-03 (Cleat)

82-1820S (Screw)

171025-004 (Interconnector)

171023-001 (CPU PCB)

034536-02 (Vibra Damp.)

A035435-06 (Regulator! Audio |! PCB)

Remove in the order indicated. (Circled numbers match the numbered instructions.) 171024-001 (Video PCB)

035745-09 (Retainer) 034536-01 (Vibra. Damp.)

175004-708 (Spacer)

72-6810S © (Screw)

Figure 3-8 \ Printed-Circuit Board Removal

3-21

Page 46

3-22 171023-001 Figure 3-8 Kangaroo™ Central Processing Unit PCB Assembly ent NOTICE TO ALL PERSONS RECEIVING THIS DRAWING juction forbidden without the specific written isi innyvale, CA. This drawing is only condireceipt nor possession thereof confers or use, the subject matter of the information shown thereon, nor

EIEN fats oe TR. lc20_ asco7e.

1c2, rere. [races Sth a7

748 4a 741 $04] Ke) A AS 1e2t a aS 4

Err @22 {is eomie. leae

B 135° tose

TALS OA

1e28 74 S04

Les tei3 7a S3e7| 7ALS00 1c22 ran si38 m4

SoD ap te fae <=> s 1c23 e & Tausees] Sus

pas3e7 Patsse7 tes => 90-7036 les: BP ag Dp7B0c

90-7036 a7 TRE 230372 aD rai s3ce|

lc29 aD BALA TC 1c37 Icac —— l74usse8| 1c38 12,

raisi7S 7aL 5367

ED 1c? (cle ba

1e24 zon 4 | | ROMs |

1c8 6eu7 ep =epD eon, | [ coms |

1c lo Roms 3,470 > ¢5,470<> facsis a custom sag gS TTT ye 1c45 O80°A% Q Ee

pa s3e8 loge PDD SERVICE ‘SWITCH cee

ES}

64,470 139. 1c47 1cS3

[741 S307)

ce, 1000 lego cao 1646 154 Pars re. [etsoe Passer 1c3t cat ica 1c55 vacsaz] Pause 7aus9e7 Se ry <=> a>

90-7836 =D P Ar3-8910

1e33 70-7036 ep Roe 250, 1K MB 373, Maintenance, Repair and Parts Kangaroo™

Page 47

Kangaroo™ Maintenance, Repair and Parts

Figure 3-9 Kangaroo™ Central Processing Unit PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 34-2N6044 Type-2N6044 Darlington NPN Transistor (TR-3, TR-4)

37-74LS00Type-74LS00 Integrated Circuit(C13, 48)
37-74LS04Type-74LS04 Integrated Circuit(1C12, 35, 36)
37-74LS32Type-74LS32 Integrated Circuit(IC 11, 21, 40, 41, 49)
37-74LS42Type-74LS42 Integrated Circuit(IC2, 31)
37-74LS74Type-74LS74 Integrated Circuit(IC30)
37-74LS139Type-74LS139 Integrated Circuit(IC1)
37-74LS175,Type-74LS175 Integrated Circuit(C38, 47, 52, 53, 58, 59)
37-74LS245Type-74LS245 Integrated Circuit(IC23)
37-74LS367Type-74LS367 Integrated Circuit(IC3, 4, 14, 37, 39, 54, 55)

62-001 SPST Momentary Pushbutton Switch (SERVICE SW) 66-118P1T 8-Station SPST, Dual-Inline-Package Switch (DIP SW) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (IC7-10, 16, 17, 24, 28) 79-42C40 40-Contaci Medium-Insertion-Force Integrated Circuit Socket (IC 15, 34, 50) 82-1820S #8 x 1¥4-Inch Flat-Head Wood Screw (for mounting PCB to cabinet) 90-7036 Random-Access Memory (IC5, 6, 32, 33) 034536-01 Foam Vibration Damper 035745-09 Plastic PCB Retainer (for mounting PCB to cabinet) 038423-03 Dual Slotted Wood Cleat (for mounting PCB to cabinet) 110000-101 100 Ohm, +5%, YW Resistor (R27-49, 52, 53) 110000-102 1K Ohm, +5%, 4W Resistor (R50, 51, 61) 110000-103 10K Ohm, +5%, “%W Resistor (R2, 5, 64, RX) 110000-122 1.2K Ohm, +5%, YW Resistor (R7) 110000-203 20K Ohm, +5%, %4W Resistor (R4) 110000-221 220 Ohm, +5%, %4W Resistor (R8) 110000-331 330 Ohm, +5%, %4W Resistor (R9, 10) 110000-332 3.3K Ohm, +5%, %4W Resistor (R6) 110000-472 4.7K Ohm, +5%, YW Resistor (R1) 110000-510 51 Ohm, +5%, %4W Resistor (R3) 110000-512 5.1K Ohm, +5%, %4W Resistor (R62) 118001-472 4.7K Ohm, 4-Element, 5-Pin, Single-Inline-Package Resistor Network (RA2) 118002-222 2.2K Ohm, 8-Element, 9-Pin, Single-Inline-Package Resistor Network (RA3-6) 118002-472 4.7K Ohm, 8-Element, 9-Pin Single-Inline-Package Resistor Network (RA1) 119003-102 1K Ohm +20% Horizontal Trimpot (VR2) 121015-103 .01 uF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C7-30) 121015-104 -1yF, +10%, 50V Radial-Lead Ceramic-Disc Capacitor (Bypass, 26 places) 121020-101 100 pF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C2) 121020-102 1000 pF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C6) 121020-471 470 pF 50V Radial-Lead Ceramic-Disc Capacitor (C3-5, 34) 121021-105, 1yF, + 10%, 16V Tantalum Capacitor (C35) 121022-104 0.1 uF, + 10%, 50V Polyester Film Capacitor (C36) 123004-101 100 uF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C42) 123004-470 47 uF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C39-41) 123004-471 470 pF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C37)

[Continued on next page]

3-23

Page 48

Maintenance, Repair and Parts Kangaroo™

Figure 3-9 Kangaroo Central Processing Unit PCB, continued Parts List

Part No. Description

123005-225, 2.2 uF, + 20%, 50V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C1) 123006-106 10 pF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C38) 133010-001 Type-2SC372 NPN 50V 400mW Transistor (FR1, 2)

136008-101Programmable Read-Only Memory, #75(IC7)

136008-102 Programmable Read-Only Memory, #76 (C8)

136008-103Programmable Read-Only Memory, #77(IC9)
136008-104Programmable Read-Only Memory, #78(IC 10)
136008-105Programmable Read-Only Memory, #79(IC 16)
136008-106Programmable Read-Only Memory, #80(IC17}
136008-107Programmable Read-Only Memory, #81(IC24)
136008-112Programmable Read-Only Memory, #82(IC28)
137168-001Type-74LS368 Integrated Circuit(1C42-46, 51)
137177-001Type-74LS138 Integrated Circuit(IC22)

137194-001 Z80 Microprocessor (IC15, 34)

137221-001Type-74LS155 Integrated Circuit(IC20)

137222-001 Type-G.|. AY3-8910 Sound integrated Circuit (IC50) 137223-001 Audio Amplifier Integrated Circuit (IC61) 137224-001 Microcomputer Custom Integrated Circuit (IC29) 171022-001 CPU PCB, Video PCB and Interconnector Assembly 171023-001 Central Processing Unit PCB Assembly 171025-001 50-Pin Flat Cable PCB Interconnector, Fujitsu FCN-707B050-AU/B 179100-050 50-Pin PCB Mount Connector, Fujitsu FCN-705Q050-AU/M (CN1)

3-24

Page 49

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 50

3-26 Figure 3: 171024-001 10 Kangaroo™ Video PCB Assembly

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

CONFIDENTIAL: Reproduction forbidden without the specific written

ion of Atari, Inc., Sunnyvale, CA, This drawing Is only condi-

‘eceipt nor possession thereot confers or

fense to use, the subject matter of the

;chnical information shown thereon, nor

drawing or any design or any right to reproduce this drawing or any part thereot. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement

with of written permission from the corporation. ira} fats 1c50 1eee 17 1ca7 telo1 leus 1129 mars] Fase7 hy) [asics] fesiea] Gases] facerzs] [acon] [etsod] [ausra]

ee cis les! teem ters eae setae. Tacs] [acsis7 asst] [eet] [erse7] [esies] Puss

fair) a> a> far fare) ics ica cas 138 1cse toe 1689 GPicios GDicur eg vase] [asics] Parsis7] [risee7] Tacsee)] [cers] farses] [arse

ROM vi om vo anne BW ica ics tc2c 1639 1690 ictoa ious 1ct32 sep vatsi7s] [acsics] [raisis7] [acsse7 ess lem vacsae] [vessq] [facsoo] [ucs7e] (itn <> tc27 1c4o Rom v3 rRomve 1c9t ictos” 1eug 1133 ARR farses] [soe Taesoe] [Fausoo] [acsto] [ruse] Be 128 eas icse ces tee eee tet eo pats ras74] facsis7] [racsis7] Pasis7] [acsis7 ge fratsoo] [tarsco

ap bere 1c29 tcaa e553 GD cee erp D icp PY e109 scat Brcise Taste] [acsiea] [raise fecorrse] [ooorreo] [concn] Pausis7] [rasse] [inisoo] ab, ics wiz Beso teas 1c se toe? \ceo tars tc108 1122 1c13e ratsoa] [alse] [vasa focoi7-c0] [loverr-oo] [oooir-oo] [paisis7] [isos] farssz @ loge, ev

§ E

i : E i ; Ne

< zt ° icie feat 14a 157 (ees, eat cas 1c109 1c12B 1197,

Gavsr4] lee fase] [esis] Gacsiea] [rasa] [Rose] [Georres] [Reorcn] [oconco] fassis7] [ausos] [acero

ter fasts] ce frsts04] § fray 1o32 14s 1656. 1eee cee Kae. tetto ares 1c138

a> a> a>

tc20 Ge icaa GD icae te 59

74 S06) T°. 23 rein D> 1125 1c139

Parsee] [74153] [oor] [Rearea] [scorreol ] Pasisz] [ruses] [aceod] re2t (E34 164 1cGo 1e7 cet 1698 peut 1c12e 16140

ALS. 4153) racsec] [74153] [ooei7-00] [fccorcal] focoir-oo] [ecoi-0c) 157 oy Pees74] aiss93] | [ras 7: 201 176 201 wusis7| [Parsee] [cose ik icio Dies 1695 _1cae ie! tere 1s va tens sete? setae Fass2] [farsic] [Fats8e] [rasa] [ecoree] [koor-co] [econo] [octco] [acea] [eave] [sr

i eu te23, (eve 149 1cee 1e73 1cac. 1e100 rains tore Faisoa favsso3] [Parsee] [Feiss | [leccr7-20]] [lecor-ooi] [ooerr-co] ecoioo] Facsis7 Lary ap aD aD Maintenance, Repair and Parts Kangaroo™

Page 51

Kangaroo™ Maintenance, Repair and Parts

Figure 3-10 Kangaroo Video PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

37-74153Type-74153 Integrated Circuit(IC42-49)

37-74LS00 Type-74LS00 Integrated Circuit (1C19, 105, 106, 118, 120, 134, 135, 139) 37-74LS04 Type-74LS04 Integrated Circuit (IC8, 11, 17, 91, 115, 117)

37-74LS08Type-74LS08 Integrated Circuit(IC20, 27)
37-74LS10Type-74LS10 Integrated Circuit(IC22, 119, 131, 133, 137, 141)
37-74LS32Type-74LS32 Integrated Circuit(IC10, 89, 90, 104, 136, 138, 140, 142)
37-74LS74Type-74LS74 Integrated Circuit(IC5, 6, 9, 28, 41, 132)
37-74LS86Type-74LS86 Integrated Circuit(IC30, 32-36)

37-74LS95 Type-74LS95 Integrated Circuit (IC121-128)

37-74LS157Type-74LS157 Integrated Circuit(IC12, 13, 25, 26, 51, 54, 64, 65, 75, 78, 92, 107-114)

37-74LS163 Type-74LS163 Integrated Circuit (IC1, 2, 14, 15, 50, 63, 74, 88, 102, 116)

37-74LS174Type-74LS174 Integrated Circuit(C129, 130)
37-74LS175Type-74LS175 Integrated Circuit(IC3, 4, 7, 16, 18, 87, 101, 103)

37-74LS193 Type-74LS193 Integrated Circuit (IC29, 31) 37-74LS367 Type-74LS367 Integrated Circuit (IC38-40)

37-74LS393Type-74LS393 Integrated Circuit(IG21, 23)

78-801001F PCB Piastic Standoff 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (IC52, 53, 76, 77) 90-123 10MHz Crystal (XTAL—Left of IC9) 100017-001 Random-Access Memory (IC55-62, 66-73, 79-86, 93-100) 110000-122 1.2K Ohm, +5%, %4W Resistor (R4) 110000-221 220 Ohm, +5%, %W Resistor (R14, 3, 9-12) 110000-561 560 Ohm, +5%, %W Resistor (R2)

121015-104.1 uF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor(Bypass, 38 places)

121020-330 33 pF, + 10%, 10V Radial-Lead Ceramic-Disc Capacitor (C4)

123004-101100 uF 16V Aluminum Electrolytic Radial-Lead Capacitor(C1, 3)
136008-108Programmable Read-Only Memory, #83(IC76)
136008-109Programmable Read-Only Memory, #84(IC52)
136008-110Programmable Read-Only Memory, #85(IC77)
136008-111Programmable Read-Only Memory, #86(IC53)
179100-05050-Pin PCB Mount Connector, Fujitsu FCN-705Q050-AU/M(CN1)

3-27

Page 52

Maintenance, Repair and Parts Kangaroo™

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING R33 CONFIDENTIAL: Reproduction forbidden without the spe- {Ext cific written permission of Atari, Inc., Sunnyvale, CA. This

  • ‘drawing is only conditionally issued, and neither receipt nor ns - 9 possession thereof confers or transters any right in, or li-
9ooJ|cense to use, the subject matter of the drawing or any de-
c|ceeQsign of technical information shown thereon, nor any right

4 an a +c ES 3 to reproduce this drawing or any part thereof. Except for

-a0Si eer ree ered
CR!a5O°under the corporation's written license, no right to repro-
coa4duce this drawing is granted or the subject matter thereo!
forum]05unless by written agreement with or written permission
c20cai0esfrom the corporation.

a Cid nN 3300 -— 35V ]

C18

|#00*C23C31

0 Seine eee Sear}; ez} C22, 24> 308 Oop 7812 7905

fe) R24,10,7W— oO

TIP 32 Bqz_1Na0oz fl cR4——} R542e 4 + He eR ea

0sielas
ce=|e[oS

=flsg $ ZH 23 258 ae 4 ch 4

"Ty “| 0 R30 CRI 1 insooz.

Uoyr

Figure 3-11 Regulator/Audio I! PCB Assembly A035435-06 B

3-28

Page 53

Kangaroo™ Maintenance, Repair and Parts

Figure 3-11 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold) 19-100P1015 1 Ohm, +3%, 7W Wirewound Resistor (R24)

19-3151021K Ohm Vertical PCB-Mounting Cermet Trimpot(R8)(Acceptable substitute is part no.

119002-102.) 24-250108 1000 pF 25V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C13) 24-250477 470 uF 25V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C1) 24-350226 22 uF 35V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C24, 31) 24-350338, 3300 uF 35V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C18, 19) 24-500105 1 uF 50V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C22, 23) 29-088 .1 uF 50V Ceramic-Disc Axial-Lead Capacitor (C20, 21)

31-1N4002Type-1N4002 100V 1-Amp. Silicon Rectifier Diode(CR, 4)
31-1N5401Type-1N5401 100V 3-Amp. Silicon Rectifier Diode(CR5-8)

33-TIP32 Type-TIP32 PNP Power Transistor (Q2)

34-2N3055Type-2N3055 NPN Silicon Transistor(Q3)

37-LM305, 5V Linear Voltage Regulator (Q1)

37-7812Type-7812 + 12V Voltage Regulator(Q8)
37-7905,Type-7905 —5V Voltage Regulator(Q9)

72-1608C #6-32 x ‘-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 72-6812S #8 x %-Inch Phillips-Head Wood Screw (for mounting PCB to cabinet) 75-F60405 #6-32 x 14-Inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly 78-16014 Thermally Conductive Silicon Insulator (Q2, 9)

79-58306.6-Position Connector Receptacle(J6, 9)
79-583089-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)

034531-01 Heat Sink 034536-02 Foam Vibration Damper (goes between PCB and cabinet wall) 110000-100 10 Ohm, +5%, %W Resistor (R29, 30) 110000-101 100 Ohm, +5%, %4W Resistor (R4) 110000-271 270 Ohm, +5%, YW Resistor (R1) 110000-330 33 Ohm, +5%, ¥4W Resistor (R3) 110000-392 3.9K Ohm, +5%, %W Resistor (R6) 110000-562 5.6K Ohm, +5%, %W Resistor (R32, 33) 110000-752 7.5K Ohm, +5%, YW Resistor (R7) 110009-027 2.7 Ohm, +5%, 1W Resistor (R5) 116000-220 22 Ohm, +5%, 10W Wirewound Resistor (R31) 116001-040 4 Ohm, +5%, 5W Wirewound Resistor (R25) 122002-102 .001 uF 50V Ceramic-Disc Axial-Lead Capacitor (C2) 122004-224 .22 uF 25V (min.) Ceramic-Disc Axial-Lead Capacitor (C8) 175004-708 Fiber Spacer (for mounting PCB to cabinet) 179051-001 Test Point (Acceptable substitute is part no. 020670-01)

3-29

Page 54

Maintenance, Repair and Parts

G. Power Supply Assembly

in place during game operation.

A035891-01 (Fuse Harness)

46-301203 (Fuse)

78-2708 (Bushing)

79-3206 (Fuse Block)

79-15021001 (Term. Block)

3A-MDA3501 (Rectifier) Fuse cover must be

(Fuse Post)

46-2017002 (Fuse)

034482.02

Figure 3-12 Power Supply Assembly A037671-01 and -02 Kangaroo™

A035888-01 (Transformer)

A021084-xx (Volt. Plugs)

034544-01 (Fuse Block Cvr.)

79-4411001

(Chassis)

037639-01 (Label)

‘A034630-01 (Filter Assy.)

46-2014002 (Fuses)

A035890-01 (Pwr. Harness)

Page 55

Kangaroo™ Maintenance, Repair and Parts

Figure 3:12 Power Supply Assembly, continued Parts List

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100V(violet)
A021084-02Voltage Plug for 120V(yellow)
A021084-04Voltage Plug for 220V(biue)
A021084-05Voltage Plug for 240V(brown)

A034629-01 AC Harness Assembly A034630-01 RFI Filter Assembly (FL1)

A035888-01Transformer Assembly(T1) (Acceptable substitute is part no. A035888-02)

A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly 29-053 27,000 pF 15V DC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type-MDA 3501 (CR1) 46-2014002 4-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F2, F4-F6) 46-2017002 7-Amp. 250V 3AG Siow-Blow Glass Cartridge-Type Fuse (F1) 46-301203 20-Amp. 32V 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x *%,-Inch Outside Diameter x %-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 03454401 Fuse Block Cover 037243-01 Metal Base Plate (goes under the power supply—not shown in illustration) 037639-01 Label for Fuse Value (F1)

037641-01Label for Fuse Values(F2-F6)

Line Voltage Range Voltage Selection Plug Wire Color 90-110 VAC (100) 105-135 VAC (120) 200-240 VAC (220) 220-260 VAC (240) Violet Yellow* Blue Brown *This is the only plug provided on the North American power supply.

NOTE

A037671-01 power supply assembly has the 120V plug A037671-02 has the 100V, 220V and 240V plugs A037671-03 has the 220V and 240V plugs

Page 56

NOTES:

Page 57

NOTES:

Page 58

NOTES:

Page 59

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately torward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm C Distributor

Address CC Operator City Country CO Other. Kangaroo™ 2nd printing

Phone City Code Country Code

Page 60

No Postage Necessary if mailed in the United States First fold

Le

BUSINESS REPLY MAIL a

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA =e POSTAGE WILL BE PAID BY ADDRESSEE Dn Atari, Inc. es Attn.: Field Service/Coin-Op Division P. O. Box 427 a Sunnyvale, California 94086 Pe a a

OT ~~ Secondfold OO

WO 4 aGpe siyy edey

Page 61

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

lf you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm CO Distributor

Address CO Operator

City State Zip O Other. Kangaroo™ 2nd printing

Area Code Phone

Page 62

First fold

Atiach Necessary Postage

Atari Ireland Limited Attn.: Field Service/Coin-Op Division Tipperary Town, Ireland

W014 eBpe sy) ede

Page 63

;

Warranty

Seller warrants thal its printed-circuit boards and parts thereon are {ree from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants thal its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace. or credit Buyer's account for such products which are returned to Seller during said warranty period, provided

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant: and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident. misuse. neglect, alteration, improper repair, installation or improper testing

In no event shall Seller be liable for loss of profits. loss of use, incidental or consequential damages

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty. according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Alari parts or accessories. Atari cannot be responsible for the quality, suitability or safely of any non-Atari part or any modification including iabor which is performed by such distributor

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. «

: : :

Page 64

ATARI INC. 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488

ad 44. © rev: conmsictone company