CATHODE RAY TOMES

Red Alert

Red Alert (Irem (GDI license), 1981) · Manual · 62 pages · 20 sections · original scan

Page 1

INSTALLATION OPERATION

and SERVICE MANUAL

WITH PARTS LIST

RED ALERTr™ is manufactured by GDI, Inc, under license from IREM Inc, OSAKA, JAPAN ©GDI imc. 1981 All Rights Reserved

Page 2
WARNING : This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance with the limits for Class A computing devices pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to correct the interference.

GAME SERIAL NUMBER LOCATION The serial number of this game is on a plate located in back of the cabinet on the lower left hand side. Please use this number in any correspondance with your distributor for service, .

RED ALERT™ is manufactured by GDI, inc., under license from IREM Inc, OSAKA, JAPAN ©GDI Inc. 1981 ALL RIGHTS RESERVED

Page 3

CONTENTS

SECTION PAGE

INSTALLATION 1 Receipt.-..- tee errr rere reer ere ey Location ......see04 Installation ,...... STereerer) Installation Checkout Procedure .. Sound and Game Control Adjustments ..+----secreseseeoee

OPERATING INSTRUCTIONS

CONELOLS oc eee ence cree ec sees escrereasenseecassseeseesesneneeseees Play Preparations ..... Playing the Game . First Attack In Daylight, Second Attack By Helicopti Third Attack At Night.... Game Frames ..... Scoring ..- How Launchers Are Lost...ccccsceccccvesccscvrccccesccccarvncensessecersee

MAINTENANCE lL

Graphic and Static RAM Test Program . Color RAM Test ..........eeerseereee Input/Output Tests .......... ROM Test...... Sound Test ..........0-

PARTS LIST 15

Character (M-33 Sub 2), GDI P/N A-20571, Parts List .. Logic (M-33 Sub 3), GDI P/N A-20571, Parts List...... Voice Assembly (UE-17B), GDI P/N A-20575, Parts List . Logic (M33-Sub 1), GDI P/N A-20565, Parts List . Audio (M-37B), GDI P{N 17B-20572, Parts List . Character (M-27S), GDI P/N 20569, Parts List . Main Logic (M-27M), GDI P/N B-20563, Parts List . . 16

-i-

Page 4

List of Illustrations

Page

Red Alert, Cabinet Model . Frontispeice Major Components ........6 2 Components Behind Coin Door 4 8 Switch DIP .......+eeee- 4 Color Pattern ...s.eeee 5 Preset Game Settings .- 7 Control Panel .....+.06 8 Color Bar Pattern ... » 12 Game Board, PCB Locations ........+ » 43 Wiring Harness, Schematic Diagram ..... ~ 4&4 Main Logic, Block Diagram ........+++ 45 Character (M-33 Sub 2), PCB .. 46 Character (M-33 Sub 2), Schematic . 47 Logic PCB (M-33 Sub 3), Schematic Diagram 48 Logic PCB (M-33 Sub 3) ......-.- 49 Voice (UE-17B), PCB ....s.e-- 50 Voice PCB (UE-17B), Schematic 51 Logic (M-33 Sub 1), Schematic Diagram 52 Logic (M-33 Sub 1), PCB ........6 53 Audio (M-37B), PCB ....... . 54 Audio (M-37B), Schematic Diagram (Sheet 1 of ) 55 Audio (M-37B), Schematic Diagram (Sheet 2 of 2) 56 Character (M-27S), PCB .sscessrenccecvescecsecee 57 Character (M-27S), Schematic Diagram 58 Main Logic (M-27M), PCB ...sesseeeeeee «. 59 Main Logic (M-27M), Schematic Diagram (Sheet 1 of 2) - 60 Main Logic (M-27M), Schematic Diagram (Sheet 2 of 2) . 61

  • ii -
Page 5

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 6

ADDENDUM TO RED ALERT MANUAL

Previously labeled PROM RAGA on the Main Logic Board (GDI-20563) has been reprogrammed, The PROM is now labeled RAGAB. This change affects several pages in the Red Alert Manual, as follows:

Page Affected Change

6 Change line 5 of ROM TEST DATA from 5AC4 to 5B84

13 Change line 5S of ROM TEST DATA from 5AC4 to 5B84

13 Change line 5 of Test Data from 5AC4 to 5B84

Page 7
CAUTION: This machine may require degaussing when installed in it's proposed location, or moved to a new location, Degaussing fis evident when color changes occur on the TV monitor as the cabinet is rotated from say, a north/south direction to an cast/west orientation, The degaussing procedure is as follows:

1, Start degaussing on left-hand side of cabinet adjacent TV monitor.

2, Next, do right-hand side of cabinet.

  • Now, degauss TV monitor from a position in monitor,

4, Finally, continue degaussing from in front while slowly stepping backwards to a point from screen.

  • Then, rotate degausser until it's field is to TV monitor before turning it "off". front of

of TV monitor about 5 feet

perpendicular

Page 8

INSTALLATION

RECEIPT

Carefully remove the game from the shipping carton. Inspect the cabinet exterior for any evidence of damage incurred in shipment. Report any damage to the carrier.

LOCATION

The game can be placed in it's proposed location upon receipt. Carefully choose one that is:

o Within 10 feet of a grounded commercial 110 volt power outlet that is free of inductive loads (motors, etc).

o Free of moisture and not a water collection area.

o Out of the direct rays of the sun.

Check machine basic specifications table for additional considerations.

BASIC SPECIFICATIONS

Power Requirements 110 volts, 60 Hz

Temperature Rangé (includes storage) 0° C (32° F) Minimum 35° C (95° F) Maximum

Humidity Range 95% Maximum

Overall Dimensions

Height 68.5 inches (1727mm) Width 24.5 inches (622mm) Depth 33.5 inches (851mm)

Shipping Weight 225 lbs (102 Kgm)

INSTALLATION

Install and check the game, as follows (see figs 1 and 2):

© Unlock and remove back panel, using key obtained from small envelope stapled to rear door,

© Locate power cord, coiled on bottom of cabinet interior, and extend cable out back of cabinet. Make sure strain relief knot in cable is positioned on inside of notch in lower right corner of cabinet opening.

o Check that all wiring connections inside cabinet, especially those connectors on game logic board (green edge connector) and TV monitor chassis (white connector), are tight.

Page 9

SPEAKER

ATTRACTION PANEL

TV MONITOR (SHIELDED)

CONTROL PANEL

COIN DOOR INTERLOCK

COIN DOOR

COIN TRAY

POWER ON/OFF

FRONT VIEW INTERLOCK

Tv MONITOR

GAME PCB AUDIO PCB

POWER SUPPLY

REAR VIEW -

POWER PLUG (GROUNDED)

. Major Components

Page 10

Pull out to defeat interlock by rear door.

Connect power plug to power outlet.

Set power switch, located on top of cabinet, to ON.

Pull out to defeat interlock by coin door, This applies power to game. Note that two incandescent lamps inside coin door light, Fluorescent lighted attraction panel above TV monitor lights, and TV monitor illuminates to display attraction sequence of game. Allow attraction sequence to repeat several cycles.

Depress coin switch on door to initiate playable game cycle.

Check audio level of game. Adjust volume control, located on coin door, to level desired.

Press interlock by coin door to disconnect power to game.

Perform installation Checkout Procedure, given in following paragraph.

Take total coins meter reading.

Close coin door and lock.

Set power switch, located on top of cabinet, to OFF.

Replace back panel.

Level machine using steel levelers provided.

REPORT ANY PROBLEMS FOUND TO YOUR DISTRIBUTOR

INSTALLATION CHECKOUT PROCEDURE

This is an equipment self test diagnostic program, and is conducted as follows:

°

°

° Unlock and remove back panel, using key provided.

Locate 8 switch DIP on game logic board (fig 3), and set switch 8 to ON,

Pull out to defeat rear door interlock.

Pull out to defeat interlock by coin door to restore power to game, and observe following TV monitor display;

1, A random speckled color pattern for about 40 seconds.

  • GR RAM OK message along with color sequencing for about 10 seconds.
  • ST RAM OK message along with color sequencing for about 3 seconds.
  • A recycling colored bar pattern.

Momentarily depress service credit switch on coin door (fig 2), and observe

Page 11

COIN DOOR

SERVICE CREDIT SWITCH

VOLUME CONTROL

COIN COIN DOOR

MECHANISM, INTERLOCK

(PULL OUT FOR POWER WHILE SERVICING)

TOTAL COINS METER

  • Components Behind Coin Door

GAME SHIPPED WITH 8 SWITCH DIP SET AS SHOWN bak RED SWITCH SETTINGS PROVIDE: bar GREEN 3 LAUNCHERS BONUS LAUNCHER AT 5,000 POINTS 1 COIN, 1 PLAY CAME PCB

AUDIO PCB

  • 8 Switch DIP
Page 12

a stationary distinct color pattern TV monitor display (fig 4). Pattern does not have to be interpreted at this time. Simply that it appears.

wy 7, ly

G

(A) SINGLE COLORED OBJECTS, SUCH AS LETTERS (B) AIRCRAFT, ETC

  • Color Pattern

° Momentarily depres: service credit switch (fig 2) on coin door, and observe Tv monitor displays;

psw DB KEY 1 00

KEY 2 ol

TIMING -- (a constantly running two digit (in Hex notation) clock)

o Depress and hold LEFT control panel button down. Observe change in KEY 1 00 and KEY 2 01 displays - while button is held down.

KEY 1 00changes toKEY 1 20
KEY 2 01changes toKEY 20 21

° bepress and hold RIGHT control panel button down. Observe change in KEY 1 00 and KEY 2 01 displays - while button is held down.

KEY 1 00changes toKEY 1 40
KEY 2 01changes toKEY 2) 41

° Depress and hold FIRE control panel button down. Observe change in KEY 1 00 and KEY 2 01 displays - while button is held down,

<5 «

Page 13

KEY 1 00 changes to KEY 1 04 KEY 2 01 changes to KEY 2 05

© Depress 1 PLAYER control panel button down, and observe KEY 1 00 display changes to KEY 1 01 during button closure.

o Depress and held 2 PLAYER control panel button down, and observe KEY 1 00 display changes to KEY 1 02 during button closure,

o «Momentarily depress coin switch on coin door, and observe the following TV monitor display appears:

ROM TEST DATA e D2ED 1 9883 2 42c9

3 BDA9

4 0355 5 aes B74

6 oro7

THIS COMPLETES CHECKOUT PROCEDURE

o =©Depress coin door interlock. to remove game power.

o Return switch 8 of 8 switch DIP on game logic board (fig 3) to OFF.

SOUND AND GAME CONTROL ADJUSTMENTS

These adjustments are located on the game logic and sound PCBs located inside the cabinet on the right side . All sounds are adjusted while game is in play at the point sound is audible. All DIP switches may be set with power disconnected from the equipment

~6-

Page 14

GAME SHIPPED WITH 8 SWITCH DIP vie SET AS SHOWN .

= RED SWITCH SETTINGS PROVIDE:

vl GREEN feet ieehies BONUS LAUNCHER AT 5,000 POINTS 1 COIN, 1 PLAY CAME PCB

AUDIO PCB 5. Preset Game Settings

ADJUSTS Overall audio level of all sounds All sounds associated with MIRV attack, including CAUTION Dive bombing attacks Firing of rocket launcher Rocket launcher explosions and attacking aircraft hits Formation and bomber aircraft

Hovering helicopters

GAME FUNCTION CONTROLLED

3 launchers per player 4 launchers per player 5 launchers per player 6 launchers per player Additional launcher on score of 5,000 points Additional launcher on score of 7,000 points Continuous free play 1 coin, 1 play lcotn, 2 plays 2 coins, 1 play Upright cabinet. Do not disturb these switches Microprocessor in game mode

COLOR ADJUSTMENTS - GREEN, RED, BLUE

Page 15

ONTROLS OPERATING INSTRUCTIONS

he functions of the control panel, and associated operating controls, are as follows:

LEFT

RIGHT

PIRE

1 PLAYER

2 PLAYER

Coin door

Power on/off Switch 2 PLAYERS

  • Control Panel

Moves rocket launcher left when depressed

Moves rocket launcher right when depressed

Fires rocket launcher when depressed (rocket must clear top of screen or destroy an aircraft or bomb before another rocket can be fired)

When momentarily depressed, game is initialized for one player only. Game continues until all rocket launchers are destroyed. Player and score is displayed on the upper left side of TV monitor.

When momentarily depressed, game is initialized for two players. Game is interrupted for first player when one of his rocket launchers is destroyed, and then ititialized for second player. When second player looses a rocket launcher, game returns to point of interruption of first player, etc. Game continues until both players loose all their rocket launchers. Score of each player is displayed on top of TV monitor. Top score of day is displayed on top of TV monitor.

Accepts coins in either slot, and all coins accepted are displayed as credits on lower right-hand side of TV monitor to a total of 99 credits. Depressing 2 \YER ‘pushbutton on control panel subtracts one credit from total. pressing 2 PLAYERS pushbutton subtracts two credits from total. Additional coins must be inserted to play game when credits dispiayed total 00.

Located on top of cabinet adjacent right rear corner. Controls power to machine.

Page 16

PLAY PREPARATIONS (with power on)

o Insert coin(s) in either slot in coin door. All coins inserted, whether intended for single or double player play, are accepted as credite, and displayed on lower right-hand side of TV monitor.

o Press 1 PLAYER button if a one player game is desired, or 2 PLAYERS button when competition between two players ie desired. Game initializes for one player, or first of two players, by blinking SCORE (1) display, located on upper left side of TV monitor. In two player competition, game initializes for second player by blinking SCORE (2) Tv monitor display, located on upper right-hand side of screen. Credit total decreases by 1 or 2, depending on player button depressed.

PLAYING THE GAME

FIRST ATTACK IN DAYLIGHT - BOMBERS IN FORMATION WITH ATTACKING AIRCRAFT. This sequence is introduced both audibly and visually. "Red alert. Enemy aircraft approaching fast. Many jet fighters approaching. 20 jet fighters approaching. Destroy all aircraft by 1100 hours or MIRV will be launched".

In this sequence, bombers in formation move from left to right across the screen, and then from right to left, etc. During the attack, some break formation and attack the the launcher. The aircraft drop bombs in an attempt to hit the launcher. Also during the attack, a special red colored aircraft flying above the aircraft in formation appears and drops a red colored magaton bomb that slowly descends on country. When hours reach 1100, present fighter attack is interrupted by a flashing CAUTION on screed, followed by appearance of the MIRV. The MIRV slowly descends, then breaks up into several bombs. They, in turn, also break up into several bombs. As & result, a shower of bombs slowly descend on the country.

Player participation during attack is to destroy all aircraft by firing rocket launcher. During the attack, player is to aviod direct hits by bombs - each of which costs hia one rocket launcher, Also during the attack, player must destroy red bomb before it lands, or one rocket launcher is destroyed.

When MIRV appears, player must destroy it completely - otherwise the landing of any one will cost the player one launcher. HINT: If you can't get out of the way of a bomb, shoot to destroy it.

SECOND ATTACK BY HELICOPTERS - DROPPING PARACHUTE BOMBS. Introduced by, " Helicopter squadron approaching. Destroy all helicopters by 1600 hours or MIRV will be launched".

Player participation during attack is te @estroy all aircraft by firing rocket launcher. During the attack, player is to keep his launcher away from red areas created by exploding bombs - or loose a launcher. Both helicopters and bombs may be destroyed by rockets. However, if parachute, but not bomb, is hit, deflated parachute will drop bomb much

faster.

MIRV attack, if launched, is a repeat of that in the first sequence above.

THIRD ATTACK AT NIGHT - HEAVY BOMBERS IN FORMATION. attack by bombers" Introduced by, "Red alert. Night

Page 17

Player is aided by two searchlights. Ohject is to destroy all aircraft. When all aircraft are destroyed, game progresses to next frame (country). During attack, player must avoid direct hits by bombs. No time limit is imposed. No MIRV will be launched,

GAME FRAMES. Game repeats above cycles thru following countries, respectively: FRANCE, USA, ITALY, GREAT BRITAIN, GERMANY, JAPAN. However, as game progresses from frame to frame, the action of the game is stepped up.

SCORING. Scores for the game are totaled,-as follows:

SCORING

> > tS 20 POINTS JET FIGHTERS We FORMATION SET FIGHTER ATTACKING 40 POINTS gS

K 8 MtGaTow sous, 60 POINTS

AUTACKING JET FIGHTERS, bestaoveo avuccatonsows 100 POINTS. on 100, 200,0R 400 POINTS

mELICoPTER i 50 POINTS

OPEN PARACHUTE BOMB 20 POINTS &

ctoseo ranacnure sous §=40 POINTS Can miGHT sowsen 40 POINTS

wine 50 POINTS eH

OW LAUNCHERS ARE LOST. Rocket launchers are lost by:

o A direct hit by a dropped bomb

o Red bomb dropped by red plane lands anywhere

o Launcher is in red area created by exploding parachute bomb

o MIRV lands anywhere

Page 18

MAINTENANCE

INTRODUCTION

Red alert incorporates built-in diagnostics as a servicing aid in the location and correction of troubles, as well as a method for the checkout of the game. The diagnostics are performed using the 8 switch DIP, located on the logic PCB (pge 7), in seven sequential test segments. These are, respectively:

a. Graphic RAM b. Static RAM c. Color RAM d. PROM e. Input/Output £. EPROM g- Sounds

TEST PREPARATIONS

The game is prepared for testing, as follows:

Unlock and remove the back door. Unlock and open the coin door. Pull out to override the rear door interlock Set switch 8 of the 8 switch DIP to ON. . Set on/off power switch to ON. wrune

GRAPHIC AND STATIC RAM TEST PROGRAM

These two tests are automatically initiated in sequence when ooin door interlock is pulled out to apply power to game. These tests check for decoding errors and other problems in addressing or data. Observe the follaying normal events:

A random color speckled pattern for about 40 seconds GR RAM OK message along with color sequencing for about 10 seconds. ST RAM OK message along with color sequencing for about 10 seconds. A recycling changing colored bar pattern. anoe

A static pattern indicates an abnormal condition. Verify by repeating tests. (All tests are repeated by momentarily interrupting power.)

COLOR RAM TEST

This test is tnitiated when the service credit switch, located adjacent the volume control (fig 2), is momentarily depressed. The TV monitor display is the following color bar pattern:

-ll-

Page 19

BAZ \S4A, RANA ARS

“fs mw oe

BLUE BACKGROUND vs SdY ORANGE oN

(A) SINGLE COLORED OBJECTS, SUCH AS LETTERS (B) AIRCRAFT, ETC

  • Color Bar Pattern

All bordering between colors should be clearly defined. If not, adjust blue, red and green potentiometers on logic PCB until borders between red and orange are clearly cefined.

INPUT/OUTPUT TESTS

This test is initiated when the service credit switch is momentarily depressed. The TV monitor displays:

Dsw D8 KEY 1 00 KEY 2 O1 TIMING -- ( a constantly running two digit (in Hex notation) clock)

Interpretation of the hexadecimal digits for each line is as follows:

Line 1 - DSW_DS8. DSW references the present condition of the 8 switch DIP; i.e., 8 the first four switches (1, 2, 3 and 4) and D the last four (5, 6, 7 and 8). Therefore, D'8 signifies that switches 4, 5, 7, and. 8& are on.

Line 2 - KEY 00. Condition of switches on control panel, as follows:

LEFT switch depressed displays 20 RIGHT switch depressed displays 40 FIRE switch depressed displays 04 1 PLAYER switch depressed displays 01 2 PLAYERS switch depressed displys 02

Page 20

Line 3 - KEY 2 01. Condition of three control panel switches, along with those on line 2:

FIRE switch depressed displays 05 LEFT switch depressed displays 21 RIGHT switch depressed displays 41

Line 4 - TIMING -- Digits indicate number of times CPU is interrupted. Counting 00 through FF uniformly and then steadity recycling is the normal condition.

ROM TEST

The ROM test is a display of ROM TEST DATA on the TV monitor, as follows:

ROM TEST DATA

D2ED 9B83 42c9 BDAY 0355 wes SBEF OFO7 AUrwneo

The test is initiated when the service credit switch is momentarily depressed.

Interpretation of ROM TEST

Game Board

ROM Coordinates Line Test Data

53Fi)D2ED
63D19B83
73B24209
83H3BDAY
93E40355
A3c5sao, SSEF
B3A6OFO7

SOUND TEST

The sound test is conducted at the completion of the ROM TEST without disturbing pewer to the equipment, as follows:

  • With the ROM TEST DATA display on the TV monitor, set all the switches on the 8 switch KIP to OFF. ROM TEST DATA display remains on TV monitor.
  • Momentarily depress service credit switch,
Page 21
  • Carefully set first four DIP switches and note audible analogue sounds, as

5. follows:

DIP SWITCH 1 2

OFF OFF

ON OFF

OFF ON OFF OFF

OFF ON ON ON

Set DIP switch 5 to ON.

Carefully set first four follows:

DIP SWITCH 1 2

OFF OFF

ON ON ON ON OFF OFF

OFF ON ON ON OFF OFF

OFF ON

SETTINGS

3 4 Resultant Sounds

OFF OFF Formation aircraft OFF OFF Dive bombers OFF OFF Helicopters ON OFF Launcher firing ON OFF Explosion #1 ON OFF Explosion #2 ON OFF Explosion #3

Keep DIP switches 6, 7 and 8 OFF.

DIP switches and note audible digital sounds, as

uae Resultant Sounds OFF OFF Melody #1. Starting sound OFF OFF Melody #2. Ending sound OFF OFF Time signal

ONOFFChirping birds

OFF ON Alarm OFF ON Excellent OFF ON Coin insertion OFF ON MIRV division

ONONMegaton bomb - long
ONONMegaton bomb:- short
ONONMegaton bomb landiz:
Page 22

PARTS LIST

Page 23

Character (M-33 Sub 2), GDI P/N A-20571, Parts List (fig 11)

| ka | Resister [220 onm av 5c) 100 ohm bw 5% 390 ohm $W 5% 180 ohm iw 5% 220 ohm iW 5% | a

390 ohm ZW 5% 180 ohm iW 5%

SN74L5472 Ic ( TL )

Connector B 10P-SHF-1

N-33 SUB~2

Page 24

Logic (M-33 Sub 3), GDI P/N A-20571, Parts List (fig 13) ca eee | BIOP-SHFo1

Ic ( TTL ) SN74LS374

PCB M-33 SU3-3

-W-

Page 25

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 26

Voice Assembly (UE-17B), GDI P/N A-20575, Parts List (fig 15)

ItemCoup .NameDescription
37R 16Resistor
38R17"220K ohm 2W 5%
39R 18”10K ohm 3W 5%

R 25

40R196.8K ohm iW 54%
41R 202.2K ohm 4W 5%

w_ | Rat R22 ee 44 R 23 es ee ee Po

—|oO wm nN a

Block Resistor THR-8-472JA : y

i [52

54c 4CapacitorO.1uF 12V Cer.

a a Ps pes C—O A eet a a De pes | SS Des fon | | 66 [cw | O.1uF 12V Cer. ;

:

69c 160.1uF 12V Cer.

ee O.1uF 12V Cer.

Page 27

Voice Assembly (UE-17B), GDI P/N A-20575, Parts List (fig 15)

tur 50 Elect

O.1uF 12V Cer. 10uFf 16V Elect. > ” °

.033ur Folyester 2200pF "

Page 28

Voice Assembly (UE-17B), GDI P/N A-20575, Parts List (fig 15)

HC18U: 6::Hz

Page 29

Logic (M33-Sub 1), GDI P/N A-20565, Parts List (fig 17) SS eee eee

7415139

O.tu 12V Cer.

B&P-SHF-1 .2

M-33 SUB-1

Page 30

_fugio (ein 3/5), GUL P/N 1/B-2057Z, Parts List (tig LY)

Ic

2 Ic 2 ” SN74L8374 3 Ic 3 Ic (RAM) - Ic 4 (7) 5 IG 5 (EP-ROM) | aie [ie7%~—t~CSY oes fe ear [~s _] Description

STATS SN74LS74

SNTAESTON

SN74LS04 SN74L5175 SN74LS 307

M51202 AY-3-8910 SN74LS 32 “SN74LS14 SN74LS02

SN74LS20 SN74LS07 NE555 LN 3900 TA7222AP LM2900 ~

x Resistor 27K ohn ZW 5% 1K ohm zi 5%

Page 31

AUGLO UIT I/B), GUL E/N A~£U2/3, Parts List (fig 1Y) —ee ee os Fares bist

Description

1K_ohm 3W 5%

Item Symbol Comp.Name

Resistor (ve) n w wn 330K ohm 4W 5%

150K ohm 3W 5%

R 12 220K ohm 4W 5% R 13 10K ohm 3W 5%.

R15 10K ohm W 5% 27K ohm iW 5% 10K ohm 3W 5 1K ohm 3W 5% 38 RT w w wo a

+ w

x

R 20 52 R 24 53 R 22 54 R 23 56K ohm iW 5% eG [os R 25 33K ohm 4W 5% R 26 10K ohn 4Ww 5% R 27 100K ohm 2W 5% 1K ohm 3W 5% R 28 R 29 10K ohm W 5% R 30 4.7K ohm 4w 5% 62 R 31 390K ohm 3W 5% 63 R 32

R_33 R34 R 35 R 36

R37 R 38 R29 = a

wu Na

wut wo wo] aa wn an

3.3K onm dv 5% 10K ohm dW 5%

_ 390K ohm aw 5%

680" ohm 3¥ 5% 22C oh: 3 5% 220% ohn iw 5% vo} ie)

= 24 -

Page 32

Audio (M-37B), GDI P/N A-20573, Parts List ( fig 19 ) a alana ee

Description

220K ohm iW 5% 10K ohm 2w 5 10K ohm 2W 5% 2.2M ohm 5% 10K ohm 2W 5% A

560 ohm tw 5% 1K ohm dw 5%

2.2K ohm fW 5% Eu ey bool Bs) SPS oO}w 82 10K ohm iW 5%

84 220K ohm 3W 5% 85 Po 86 470K ohm iw 5% 87 1K ohm 3W 5%

&

a A Ba se

R 63 470K ohm dW 5% a 470K ohm iw 5% 10K ohm iw 5% wo a) Ol Ol Oy DD] DH) o CO Al H]

68K ohm 1W5%

100K ohm 3W 5:3 68K onm dy 5%

Page 33

Audio (M-37B), GDI P/N A-20573, Parts List (fig 19)

106 R75 47K ohn 3 5% 107 R 76 1.5K ohm 3W 5% OP a Z

ae ee ce . (114 | 100K ohm 3W 59 R 84 " 47K ohm AW 5% Resistor

JuF 12V Cer.

33pr Cer.

  • O01uF Cer.
Page 34

Audio (M-37B), GDI P/N A-20573, Parts List (fig 19)

Comp.Name

Capacitor O.1uF 12V Cer.

" 0.01uF 50V Cer. e145 : O.1uF 12V Ger. O16

oa a o73 148 Cc 20

149 c 21 O.1uF 50V Mylar. 150 Cc 22 o.01uF 50V " Cc 23 Cc 24 Cc 25 Cc 26

C 27

Co 0.O01uF 50V Mylar.

O.1uFP 12V Cer. 0.01uF 50V Mylar. "

O.1uF 12V Cer.

0.01uF 50V Mylar. 22uF 10V Elect. 2,2uF 16V Elect,

O.1uF 12V Cer.

"

0.0047uF 50V iylar. O.lur 12V Cer.

0.001uF 5OV iylar. 162 Cc 34

Lee [3s

pee

120uF 19V clect,

Page 35

Audio (M-37B), GDI P/N A-20573, Parts List (fig 19)

174Cc 46CapacitorO.1uF 35V Tantalum,
175© 4747uF 16V Elect.
176c 480.047uF 50V Mylar.

O.1uF 12V Cer. 178 ¢ 50 " 179 0,0047uF 50V Cer. c 52 47uF 16V Elect.

181¢ 5310uF 16V Elect.

183 O.tu® 50V kylar.

184Cc 56O.tuF 12V Cer.
185Cc 57100uF 25V Elect.
186c 581000uF 10V "
187c 590.047uF 50V Mylar.

100uF 25V Elect.

GF 160 Bleck.

192c 640.0022uF 50V Mylar.
194Cc 66o80pF 50V Cer.

Cc 67 Ju? 50V Elect, 10uF 16V Elect. 197 c 69 198 c 70 199 c 71

200 Cc 72

201 c 73 202 c 74

203 C73 204 C74 c 75 10uF 16\ Elect,

Page 36

Audio (M-37B), GDI P/N A-20573, Parts List(fig 19)

Deecription

HC18U 12.5icH2Z

25€16150

25A1015Y

Page 37

Character (M-27S), GDI P/N A-20569, Parts List (fig 22)

SN74LS172N SN74L5175N

SN74L585N SN74LS 160i}

Page 38

Character (M-27S), GDI P/N A-20569, Parts List (fig 22)

Ic

374-GSN74L5175N
3e4-Hg

12114

SN74LSO8N SN74LS157N 'SN74L532N SN74LSO4N

SN74LS1660N

SN74LS139N

ee ee

55R1Resistor1K RV 5%
5R 2“rn
Page 39

Character (M-27S), GDI P/N A-20569, Parts List (fig 22)

Description

-luF 12V Cer,

Page 40

Character (M-27S), GDI P/N A-20569, Parts List (fig 22) a ial a ana eee

a 107 Capacitor «1uP 12V Cer 108 | -c 44 109 Cc 42 110 c 43 " ae ee a a oe or

Po 113 :

115 Connector FCP26 FCF40

Page 41

Main Logic (M-27M), GDI P/N B-20563, Parts List (fig 24)

B10P-liVG .2 SN74L5374N [item | |_ Symbol | Comp.ivame

w a SN74LS151AN SN74L3164N SN74LS175N SHTALSOOH w SIP TPL? PLPLPPRIP PRIS) alt

im ble (EP-RO%) 127 3200r725 32 i ( ) ( je ( )

3-H | 23 3-I ) 24 4-a SN74L8 1661 25 " 4- = TLALSBGi ad stato

ee =

Le SH74éL174)

“SIT S174 5-0 2 eth eet

  • 3% whe ay
Page 42

Main Logic (M-27M), GDI P/N B-20563, Parts List (fig 24)

5-F Connector B10P-HVQ .2 5-H Ic SN74LS138N J SN74LS3607N SN741LS138N 14116 [|

3L

[ae]

4T | 48 | | 49 | | 5° a1

53 7-F SN74LS175N 54 14027

SN74LS374% SN74LS86N SNT4L583AN SN74LS86N

SN74LS174N SN74L514N

SU74LS74N Sui74LS20H LNT4LSben

SN74LS161Ali S74 bu 307:

we Te bs02i

Page 43

Main Logic (M-27M), GDI P/N B-20563, Parts List (fig 24)

SynbolComp. NaveDeacription
2B9-KIchay 1202
749-L«|5 55P
7510-A7SN74LSO4N
77"SN74L5161AN

78 " " SN74LS161AN

80"SN74LS367N
a"SN74LS00N
82CiSN74L5 10N
1U-K7SN74L5 16 1AN
8410-1SN74LSO4N
11-ArSN74LS161AN
| 86 |"SN74L527N

87 SN74LS161N

89 SN74LS161AN 90 SNT7eLSO4h 91 $..74LS08N

92 So T4L8 1041

TR 1Transistor286710
TR 3"25C2120
TR"“
TR 5be28C710
195TR 8""
106ee)"2502120

ies

Page 44

Main Logic (M-Z/7M), GDI P/N B-20563, Parts List (fig 24)

470 ohm 4W 5% 1K 4W 5%

270 Ohm Ww 5% 2.2K aw 5% 1.5K iw 5% 220 oh AW 5% -

"

1K 3W 5% 470 ohm iw 5%

2.2K aw 5% 1.5K AW 5% 220.

220 ohm iw 5% 1.5K 2W 5%

15K 2W 5% 10K 2 5%

Page 45

Main Logic (M-27M), GDI P/N B-20563, Parts List (fig 24)

145R_33Resistorjo
146R 34"1K _4W 5%

R 35 100 ohm 4W 5% 148 [B36 a a RT 50 | R38 Pe

152R 401K iw 5%

R41 12K iw 5%

155 | R43 ai ee 157 R45 158 R 46

= n w 161 | R49 po R52 — 4a

na

a

162 R 50

R 53

  • R54
R 55Resistor470 ohm 4W 5%
R 56w7

c

160R 48100 ohm iW 5%

R51

1Capacitor22pF 50V Cer

-047uF 50V Mylar Pc3 [tur TeV Cer.

-luF 12V Cer.

22nF_ 50V Cer. aya Wal!

a foal

Page 46

Capacitor 2O47uF 50V Nylar " Conip.Name Symbol

ala aia

alo|olola alo SS 185 " 186 c 12 7 187 c 13 «luF 12V Cer De 189 C15 Po Cc 16 c 17 c 18

A A A

a -[00[~eae fp I A a a Oe a FA P25 [es PCS SN [207 [ess Oi Ee a Peo [exe [Od Dan [ef OE res [es fo A as | ea

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 48

Main Logic (M-27M), GDI P/N B-20563, Parts List (fig 24)-

Cc 77Capacitor~luF 12V Cer

o78 * T_T i a a V c 60 Cc 81 Item

256 c 82 a

SA iS)

C84 C65 ¢86 261 c 87

262c 88JuF 50V Elect.
5}0 oser

264__| 6 30 AN A a

AAa

On a A LC a EA A CE A BC Ea A A A a a

aaa

a

Page 49

Main Logic (M-27M), GDI P/N B-20563, Parts List (fig 24) [tres_| symtor | coup-tane___[__deseription ___|

pws fae [TS CN A a a (GO Os ee ed Os A a P30 TT) a a TE) Es A A

A = pao [id Seer SSSC*dSCi oe SSCC*d

Page 50

MAIN LOGIC PCB

(M-27M)

CHARACTER PCB

(4-33 SUB 2) a

LOGIC PCB

(M-33 SUB 1)

(M-278)

AUDIO PCB

(4-378)

a LOGIC PCB

(M-33 SUB 3)

VOICE PCB

(UE-17B)

  • Game Board Assembly, PCB Locations
Page 51

FLUORESCENT CAMP COMM DIOL Zep +/2

OTE SAE AST

SSOLATION ORMER SWITCH POWER SUPPLY

Zz [B] re varer

2A.

lo] ox YSuMUygsy Pure Ve VP PPV 2| 4| 6lolz[4 [2] TRAM

\ z rE u 3} 8 Ne 3] 8 g u y 8

Ty. MOM ITER Wioce re

FRONT IAI TER otk

LACK

£EAR INTER LOC Yetlow

MAIN on /or=

VAR STOR

BED. COIN METER,

teacpe CeEr

LOCKOUT COIL ae sz-) MOM TIE SIDED

  • sro) vs

t+20 tr+—+ eer io Bence loccgur cas BLACK MITE CERN CIS PLAY Lienge ws | 9

/ | GwOo ZL GAS

  • EFS Fl gwo roe gy
4[eT~22

I CIRIRIENENES mo os ofr

fo “4 of 10 | SpocrTse LE

FILE G Ue SHOCTER L/GHT! 4E | Secortk SIGHT) Ler

Com SEeIce2.3
:iyay
seemreSIs 3 2
3volumeasa

! ; atti | || 2 Gin. / {_

:speacee|‘HOBIE. E rhc

¥ RED

||i
||esl 77
|7++24)727

I 25) = PEL ELL

|+26| SPEREER

I 2

|Black|2a eae
;+xrea Wicker|
|i7 | Reve WEEE

Zz

Irei|(32, 0
HITE|ze]

CONTROL PANEL |

SeanceScAace!rt
aa/_ildd
riageeSry
oO SEEK TGakey|
.Btacxi
es||

fee Seve | Pave Bo retcow rELcow

GDlInc. 5945 N.ROGERS AVE. CHICAGO, IL.60646/ 1312] 286-6722

Wiring Harness, Schematic Diagram

Page 52

i { Chrstar H rr] ariel

CammaiteaHerwysaieinenneeSES
98C 1 LATAgous,OD cat gene

covatta Her,roejat Sync Sigeata

Yestical Syae S'gnels

Sccailed Koeiesrual Syac S-geats SCROLED

CONTROLER Oss. eu Oe OF

Seeatted Hatsserial ard Verticg) Syne

Adders,

ARALLEL TO . SURIAL . . . / CONYEATOR ~ To cates video

2 ~ . a.G.6

PRIGRAN7brSEN(FSTOR —=

MEMORY

dt is AQIRESS KC MARASTCA Haroatal land PARALLEL TG Verticat Sy

5 =. PaRAEL TO TAI- STATE conn . ; CONVERTOR lauset id er . Adétess ait FS TR St ss surtin

GDliInc. 5945 N. ROGERS AVE. CHICAGO, IL.60646/ (312) 286-6722 NAME . 19 AAIN hegic, Bleck Diagram

Page 53

74LS374

4 GDI Inc. 5945 N ROGERS AVE. CHICAGO. IL .60646/ 1312] 286-6722 “4 206/€ PCB -33- SUB-3 AGDI) GDI Inc. CHICAGO, 1L.60646/ (312) 286-6722 "“13 £OG/C PCB 4-33 - SUBS

Page 54

ISID SOD

IRST7.5 ALE|30

+ 12WA) + HLDA|38

Ad7Hg 2. AB6) 20) ADS|17 1 ADAG 1 AD3IIS AD2f14 ADIN3. ADO|2

NAME 1§ VOKE PCB ASS VE-178 GDI Inc. 5945 N. ROGERS AVE. CHICAGO, IL.60646/ (312) 266-6722

Page 55
  • 7 oy oa 3 i2 > 2 za za
3oof3o 2%
v9aea v9wo

te a thee

13wep1+

7 aT. v3 | 2S 2 2 zu zu

2a of3o = 3
weIwva eo
23°
Fdés
32.

Ae so ae” 8 Wa “a 8

19wprywn

5945 N. ROGERS AVE, CHICAGO, IL.60646/ |312/ 286-6722 Logic (M33-Sub 1), GDI P/N 17A-20564, Schematic Diagram GDIInc. 5945 N ROGERS AVE. CHICAGO, IL .60646/ 1312) 286-6722 Logic (M33-Sub 1), GDI P/N A-20563, Assembly Diagram

i. - - 52 -

Page 56

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 57

R20 1K MEOQUT

NOISE

2SC1815

So Ss Sa $3 Sa $5 Ss Sr

.GDIInc. 1 5045 N. ROGERS AVE. CHICAGO, IL.60646/ 13121 286-6722 ™ 7

  • 20! Audio (4-37B), GDI P/N 17B-20572, Schematic Diagram

(sheet 1 of 2

Page 58

21 | Audio (M-37B), GDI P/N 17B=20572, Schematic Diagram ¢ sheet 2 of 2) GDlInc. 5945 N. ROGERS AVE. CHICAGO, IL.60646/ [3121 266-6722 pee on R56 R57, we [ay EE, a val 03 "22x af Fx | Boxy ar 5 —

FEB, i + f \ | oy te@ FO.

2SCIBI5 RAB F 59 RSQ R52. 1 fetes

vila Bg a7 at Lp. | Daa

7% fig BSCIBIS O®@ +12V. _ ® SPH Soy Hor Cin \. Bb ra7eeeap ph ae cao oe al e ic

%% @---- POLYESTER FILM CAPACITOR

@®--- TANTALUM ELECTROLYTIC CAPACITOR

OUT

Page 59

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 60

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 61

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 62

Ie Bee rau oY ye : 7) ; rah a crt . LF KAOC4Y, sats a H AZ H-BLANK _ 3, H-BL ANK® e ne H:SYNC © GH-BLANK 5; 1A

RS ‘es TRI

(ib) | GDiinc. 5945 N. ROGERS AVE. CHICAGO, IL.60646/ 1312) 286-6722 "6 Main Logic (M-27M), GDI P/N 17B-20562, Schematic Diagram (sheet 2 of 2)