Major Havoc TM-268 1st Printing Conversion for SD-BW-GRAV
Major Havoc (rev 3) (Atari, 1983) · Technical Manual · 54 pages · 26 sections · original scan
ATART
(© AWarnarcommurcatons Gomeany
Space Duel”, Black Widow",
and Gravitar”
for
Conversion Instructions
The Adventures of
Atari Customer Service
If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at one of these Atari Customer Service offices:
UNITED STATES Parts and Service
Atari, Inc. California Customer Service Office 737 Sycamore PO. Box 906 Milpitas, CA 95035 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) s From California, Alaska, or Hawaii (408) 943-1120 POW From anywhere else in the continental United States toll-free (800) 538-1611
EUROPE Parts and Service
Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT) = = 062-52155
The Adventures of
- AfiaJor flavoc ”
Conversion Instructions
for
Space Duel”, Black Widow", and Gravitar"
© 1984 by Atari, Inc. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic, or elec tronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws, Courts can in pound infringing articles while legal action is pending. If intringers are convicted, courts Can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five vears Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari, Inc 790 Sycamore Drive PO. Box 906 Milpitas, California 95055
Printed in the U.S.A 4N
Safety Summary
‘Vhe following safety precautions apply to all game operators and service personnel. Specitic warnings and cautions will be found throughout this manual where they apply
A&A WARNINGS A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid ¢lectrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. ff you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an clectrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game.
AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game's power supply. Disconnect Power During Repairs. To avoid clectrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or met objects! Always discharge the high voltage from the CRT before servicing this area ofthe game, To discharge the CRT: Atach one end of a large, well-insulated, 20-kV jumper towround, Momentarily touch the free end of the grounded jumper to the anode by sliding. itunder the anode cap. Wait two minutes and discharge the anode again Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion Use the Proper Fuses. To avoid clectrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating. and current rating. In addition, the fuse cover must be in place during game operation
Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. Ifthey do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty:
we ue ee
TABLE OF CONTENTS
Introduction. . 2... 2. ..2. Kit Parts Inventory. ...... Tools Required. . 2... 2.2.4.
Assembly Removal Instructions . . Remove the Attraction Panel . Remove the Control Panel. . . AAO wp
ia AOA Remove the Wells-Gardner Deflect i ion Remove the Amplifone Deflection PCB . . Remove the Game PCB... .. Remove the Power Supply ......
sembly Modification Instructions. . . Modify the Power Supply. ..... Modify the Wells-Gardner Deflection PCB... Modify the Amplifone Deflection PCB PCB.
Modify the Control-Panel Harness. ...... Modify the Rear Access Panel. ........
Assembly Installation Instructions. .......
N. Oo. Pe
Q. R. s. T. Ue Vv. Ww. xX. Y. Install the Install the Install the Install the Install the
Install the Install the Install the Install the Install the Inspect the Side-Panel Decals (optional). . Attraction Panel. ... 1... Wells-Gardner Deflection PCB. . Amplifone Deflection PCB. ... Control Panel. ........
Major Havoc PCBs. Power Supply. . . Fan... ee ee Self-Test Chart . Labels... ... Major Havoc Game. Adjust the Display. ..... Set the Option Switches . .. Update the Game Documentation
iv wn
worssa.s.
Figure Figure Figure Figure
Figure Figure Figure Figure
Figure Figure Figure Figure
Figure Figure Figure Figure
Figure Figure Figure
Table 1 Table 2 Table 3 PWN
oyu LIST OF ILLUSTRATIONS
Removing and Installing the Attraction Panel. . . Removing and Installing the Control Panel... . Removing and Installing the Display Deflection PCB. Removing the Game Printed-Circuit Board. ....
Modifying the Power Supply. . 2... 2 eee eee Type-1N754A and 1N756A Zener-Diode Connections. . Modifying the Wells-Gardner Deflection PCB. ... Modifying the Amplifone Deflection PCB. .....
Modifying and Installing the Control Panel Harness. . . Modifying the Rear Access Panel & Installing the Fan. . Installing the Side-Panel Decals... 1... ee eee Installing the Major Havoc PCBS ........--
Installing the Labels... 1... 2.2. eee eee Adjusting the Display... 1.22. - eee eee Input Protection Circuit Schematic. ....... Wells-Gardner Deflection PCB Schematic (Ver 2, 3,
Wells-Gardner Deflection PCB Schematic (Version 1). Amplifone Deflection PCB Schematic for TM-194. . Amplifone Deflection PCB Schematic for TM-239. .
LIST OF TABLES
Conversion Kit Parts... ees eee eee eee
Display Versions .. 1. eee eee ee ee eee
INTRODUCTION
This document includes the instructions necessary for changing your upright Space Duel, Gravitar, and Black Widow game into a Major Havoc game. The instructions include: (1) modifying the power supply, display, and rear access panel; (2) replacing the control panel and attraction panel; and (3) installing a fan, decals (optional), and Major Havoc game printed-circuit boards (PCBs). The procedures are organized to accomplish the change in the most efficient manner.
A Major Havoc instruction manual and schematic package is included with the kit. Keep your Space Duel, Gravitar, or Black Widow instruction manual and schematic package for information pertaining to those parts of the game that are not modified by this Major Havoc conversion.
Do not discard this document after the conversion is completed. Keep this document as a supplement to the Major Havoc Operators Manual and display manual.
Major Havoc Conversion Instructions TM-268
KIT PARTS INVENTORY
The parts listed in Table 1 are included (or are available as options) in the Major Havoc Conversion Kit.
Table 1 Kit Parts A042425-01
| Part No. | ant it: | Descru |
| A038088-01 | Opt ional | Input Protection Circuit PCB Assembly |
| A041347-21 | 1 | Major Havoc PCB Assembly |
| A042427-01 | 1 | Control Panel Assembly |
| A042441-01 | 1 | Major Havoc Conversion PCB Assembly |
| A042445-01 | 1 | X-Y Display Kit--includes |
| 31-1N4002 | 4 | Type-1N4002 Diode |
| 32-1N756A | 2 | Type-1N756A, 8.2 V Zener Diode |
| 110000-303 | 1 | 30 k2, +5%, 1/4 W, Resistor |
| 131002-001 | 2 | Type-1N754A, 6.8 V Zener Diode |
| A042448-01 | 1 | Fan Harness Assembly |
| A042578-01 | 1 | Control-Panel Harness Kit--includes |
| A042574-01 | 1 | Harness Assembly |
| 178065-100 | 5 | Wire and Cable Tie (Miniature) |
| 178068-002 | 2 | Cable Tie Mount (Adhesive Back) |
| 179002-001 | 4 | Tap Splice Connector |
| A043629-01 | 1 | AC Harness |
| 72-HA4804S | 1 | #8-32 x 1/4-Inch, Cross-Recessed |
Pan-Head Screw
| 72-6636S | 4 | #6 x 2-1/4-Inch Cross Recessed, Self- |
Tapping Screw
| 75-99518 | 4 | #8-32 Nut/Washer Assembly |
| 78-24012 | 4 | Beaded Nylon Tie |
| 034536-02 | 1 | 1/2-Inch Foam Pad |
| 034536-03 | 1 | 1-1/8-Inch Foam Pad |
| 037410-01 | 1 | Attract ion-Panel Glass |
| 042414-01 | 1 | Label Kit--includes |
| 038158-01 | 1 | Conversion Kit Label (Non-UL) |
| 039450-01 | 1 | FCC Compliance Label |
| 042421-01 | Opt ional | Left Side-Panel Decal |
| 042421-02 | Opt ional | Right Side-Panel Decal |
| 042424-01 | 1 | Attract ion-Panel Film |
| 042450-01 | 1 | PCB Mounting Bracket |
** continued on next page **
‘TM-268 Major Havoc Conversion Instructions
Table 1 Kit Parts, continued A042425-01
| Part No. | Quantity | Description |
| 042579-01 | 1 | Control-Panel Wiring Diagram |
| 171002-001 | 1 | Exhaust Fan |
| 176015-110 | 1 | #10 x 5/8-Inch Cross-Recessed Deep- |
Thread Pan-Head Screw
| 178065-100 | 2 | Tie Wrap |
| 178093-001 | 1 | Fan-Blade Guard |
| CO-252-03 | 1 | Major Havoc Conversion PCB Supplement |
| CO-252-05 | 1 | Major Havoc Encoder Wheel Supplement |
| SP-252 | 1 | Major Havoc Schematic Package |
| ST+252-01 | 1 | Major Havoc Label with Self-Test |
Procedure and Option Switch Settings
| ™252 | 1 | Major Havoc Operators Manual |
| ‘TM-268 | 1 | Major Havoc Conversion Instructions |
for Space Duel, Gravitar, and Black Widow
TOOLS REQUIRED
The tools listed in Table 2 are required to perform a complete conversion.
Table 2 Tools Required
Description Purpose
#2 Phillips Screwdriver Removing the game PCB, power supply, and Amplifone Deflection PCB. Modifying the power supply. Installing the power sup— ply and fan 1/8-Inch Allen Wrench Removing the attraction panel 1/4-Inch Hex Driver Removing the Wells-Gardner Deflection PCB 11/32-Inch Hex Driver Removing the power supply. Modifying the power supply 7/16-Inch Hex Driver Removing the control panel. Installing the control panel 15-27 W Soldering Iron Modifying the Deflection PCB 1/4-Inch Drill Bit Modifying the rear access panel Pliers Modifying the control-panel harness #11 X-ACTO Knife (optional) Installing the side panel decals
Major Havoc Conversion Instructions TM 268
ASSEMBLY REMOVAL INSTRUCTIONS
A——._ eric
To avoid electrical shock, unplug the game before performing the conversion procedures.
These procedures must be performed by qualified service personnel. All interior and exterior surfaces of the cabinet and the working area should be clean and free of foreign material before starting the procedures.
The following procedures are arranged in the sequence recommended for performing the game conversion. The parts of your game that are affected by the conversion are removed, modified, and the new Major Havoc parts are installed.
A. REMOVE THE ATTRACTION PANEL
Perform the following procedure to remove the attraction panel fran the game cabinet (see Figure 1).
- Use a 1/8-inch Allen wrench to loosen the three screws securing the bottan retainer to the cabinet and to the bottom of the attract ionpanel glass.
- Use a 1/8-inch Allen wrench to remove the three screws securing the top retainer to the cabinet and to the top of the attract ion-panel glass.
- Remove the top retainer.
- Remove the attraction-panel glass and film.
B. REMOVE THE CONTROL PANEL
Perform the following procedure to remove the control panel fran the game cabinet (see Figure 2).
- Unlock and remove the rear access panel.
'™-268 Major Havoc Conversion Instructions
Allen-Head Screws
Top Retainer
Attraction-Panel Glass
Bottom Retainer
Figure 1 Removing and Installing the Attraction Panel
Major Havoc Conversion Instructions T™-268
Spring-Draw Latches Control-Panel Harness
Yherinch Hex Nuts
Control Panel
Figure 2 Removing and Installing the Control Panel
‘T™M-268 Major Havoc Conversion Instruct ions
- Reach through the rear of the cabinet and release the spring-draw latches on each end of the control panel.
- Open the control panel and disconnect the control-panel harness connector fram the game harness.
- Use a 7/16-inch hex wrench to remove the three nuts and washers securing the control panel to the cabinet (save the mounting hardware for reassembly).
- Disconnect and remove the control-panel harness fram the control panel. Save the Space Duel, Gravitar, or Black Widow cont rol-panel harness and green ground-wire securing hardware for reassembly.
C. REMOVE THE WELLS-GARDNER DEFLECTION PCB
The following procedure applies to those Space Duel, Gravitar, and Black Widow games that use a Wells- Gardner display. If your game has an Amplifone display, proceed to procedure D. Remove the Amplifone Deflection PCB.
Perform the following procedure to remove the Wells-Gardner Deflection PCB fran the display (see Figure 3).
A—— waninc
High voltages may exist in the display circuitry, even with power disconnected. Use extreme caution. Do not touch the display circuitry with your hands or with metal tools.
- Discharge the high voltage fran the cathode-ray tube (CRT) before proceeding:
a. Attach one end of a large, well-insulated, 18-gauge jumper wire to ground.
Major Havoc Conversion Instruct ions TM-268
15-Pin Molex Connector
Wells-Gardner Display Neck PCB Connector
Deflection PCB
‘Screw and Spacers
Amplifone Display
Figure 3 Removing and Installing the Display Deflection PCB
‘TM-268 Major Havoc Conversion Instructions
b. Momentarily touch the free end of the grounded jumper to the CRT anode by carefully sliding the jumper under the anode cap.
c. Wait two minutes and repeat step lb.
- Disconnect the 15-pin Molex connector fram the mounting bracket on the display chassis and the harness connectors from the Deflection PCB and the Neck PCB.
- Use a 1/4-inch hex driver to remove the two screws securing the Deflection PCB to the display chassis.
- Remove the Deflection PCB fran the display.
D. REMOVE THE AMPLIFONE DEFLECTION PCB
The following procedure applies to those Space Duel, Gravitar, and Black Widow games that use an Amplifone display. If your game has a Wells-Gardner display, perform procedure C. Remove the Wells- Gardner Deflection PCB.
Perform the following procedure to remove the Amplifone Deflection PCB from the game cabinet (see Figure 3).
- Disconnect the harness connectors from the Deflection PCB.
- Use a Phillips screwdriver to remove the screw and spacers securing the top right corner of the Deflection PCB to the cabinet.
- Carefully slide the PCB straight out of the slotted cleats.
E. REMOVE THE GAME PCB
Perform the following procedure to remove the Space Duel, Gravitar, or Black Widow game PCB fran the game cabinet (see Figure 4).
- Disconnect the game harness edge connectors fran the game PCB. If the edge connectors are secured with screws or tie wraps, remove the screws or tie wraps before disconnecting the edge connectors fran the PCB.
Major Havoc Conversion Instructions
Washer
Slotted Cleats.
Figure 4 Removing the Game Printed-Circuit Board TM-268
TM-268 Major Havoc Conversion Instructions
- Use a Phillips screwdriver to remove the screw, washer, and two spacers securing the top right corner of the PCB to the cabinet wall.
- Carefully slide the PCB straight out of the slotted cleats.
F, REMOVE THE POWER SUPPLY
Perform the following procedure to remove the power supply fran the game cabinet.
- Disconnect the four harness connectors (Jl, J2, J4A, and J5).
- Disconnect the power cord fran the power supply.
- Use a 11/32-inch hex driver to remove the nut and star washer fran the ground screw attaching the green grounding wires to the power supply.
- If applicable, cut the cable tie located on the rear right corner of the power supply chassis.
- Use a Phillips screwdriver to remove the four screws securing the power supply to the cabinet.
- Remove the power supply fram the cabinet.
Major Havoc Conversion Instruct ions ‘TM-268
ASSEMBLY MODIFICATION INSTRUCTIONS
The following procedures describe the modifications required for this conversion, Provide a clean work surface on which to perform the modifications to the assemblies removed fram the game cabinet.
G,. MODIFY THE POWER SUPPLY
Perform the following procedure to modify the power supply (see Figure 5).
Set the power supply upside down on a clean work surface.
Install the three-pin AC harness connector with the white wire on the left end of the connector.
Connect the white wire fran AC harness connector J4B to the terminal lug adjacent to the white wire from connector J4A.
Connect the black wire fran AC harness connector J4B to the terminal lug adjacent to the black wire fram connector J4A.
Use a 11/32-inch hex driver to remove the nut and star washer from the ground screw securing the green wires and the line filter to the power supply. Remove the ground screw.
Attach the green wire fram connectors J4A and J4B, and the green wire fran connector J2, to the ground screw.
Insert the ground screw, with the green wires attached, through the line filter bracket and power-supply chassis.
Use a 11/32-inch hex driver and a Phillips screwdriver to secure the nut and star washer (removed in step 5) to the power supply.
Check that the power supply fuses match the ratings given on the labels located near the fuse block and the cartridge fuse holder.
TM-268 Major Havoc Conversion Instruct ions
Figure 5 Modifying the Power Supply
Major Havoc Conversion Instructions 'TM-268
H. MODIFY THE WELLS-GARDNER DEFLECTION PCB
The following procedure applies to those Space Duel, Gravitar, and Black Widow games that use a Wells- Gardner display. If your game has an Amplifone display, proceed to I. Modify the Amplifone Deflection PCB.
Four versions of the Wells-Gardner display were used in the Space Duel, Gravitar, and Black Widow games. Perform the preliminary procedure for all versions of the Wells-Gardner display, then refer to Table 3 to determine which version of the four displays was installed in your game. Perform the additional procedure for that version.
When soldering camponents to the display circuitry, apply just enough heat to provide a proper electrical connection. Excessive heat can damage the semiconductor material.
Preliminary Procedure
Perform the following procedure to modify the Wells-Gardner Deflection PCB (see Figures 6 and 7).
- Set the Deflection PCB on a clean work surface.
- Connect two type-1N754A Zener diodes together, anode to anode, as shown in Figure 6. Use a soldering iron to solder the two anode leads together.
Solder Here
K- cf
Figure 6 Type-1N754A and 1N756A Zener-Diode Connections ne]
TM~268
1N754A Zener Diodes
1N4002 Diodes
1N754A Zener Diodes
1N4002 Diodes
Major Havoc Conversion Instruct ions
1N756A Zener Diodes
1N4002 Diodes
1N756A Zener Diodes
1KQ, % Wresistor installed in the procedure for Version 3 isattachedto this point.
1N4002 Diodes
Figure 7 Modifying the Wells-Gardner Deflection PCB
Major Havoc Conversion Instructions 'T™M-268
10.
ll.
12.
13.
14,
15. Connect two type-1N756A Zener diodes together and solder as described in step 2.
Examine the soldered side of the Deflection PCB removed fran the display and determine which of the two PCBs shown in Figure 7 matches your PCB.
On the camponent side of the Deflection PCB, locate the yellow wire (top right side of the PCB).
Solder one cathode lead of the two type-1N754A Zener diodes (soldered together in step 2) to the yellow lead on the soldered side of the PCB as shown on the appropriate illustration in Figure 7.
Solder the other cathode lead of the two type-1N754A Zener diodes to ground as shown on the appropriate illustration in Figure 7.
On the component side of the Deflection PCB, locate the orange wire (near top center of the PCB).
Solder one cathode lead of the two type-1N756A Zener diodes (soldered together in step 3) to the orange lead on the soldered side of the PCB as shown on the appropriate illustration in Figure 7.
Solder the other cathode lead of the two type-1N756A Zener diodes to ~ ground as shown on the appropriate illustration in Figure 7.
On the camponent side of the Deflection PCB, locate connector P600 (right center of the PCB).
Solder the cathode lead of a type-1N4002 diode to pin 1 and the anode lead to pin 4 of connector P600 on the soldered side of the PCB as shown on the appropriate illustration in Figure 7.
Solder the cathode lead of a type-1N4002 diode to pin 5 and the anode lead to pin 7 of connector P600 on the soldered side of the PCB as shown on the appropriate illustration in Figure 7.
On the component side of the Deflection PCB, locate connector P700 on the soldered side of the PCB (left center of the PCB).
Solder the cathode lead of a type~1N4002 diode to pin 1 and the anode lead to pin 4 of connector P700 on the soldered side of the PCB as shown on the appropriate illustration in Figure 7.
TM-268
16. lead to pin 7 of connector P700 on the soldered side of the PCB as shown on the appropriate illustration in Figure 7.
- Refer to Table 3 to determine which of the four versions of the Wells-Gardner display has been installed in your game.
Table 3 Display Versions
Determine Procedure
Deflection PCB has two large, black, Version 1 tubular capacitors, C804 and C805, installed below top center of PCB.
Input Protection Circuit PCB is Version 2 installed (piggyback) with a 1 ke, +5%, 1/4 W resistor connected between the Input Protection Circuit PCB and the Deflection PCB. .
Input Protection Circuit PCB is Version 3 installed (piggyback) but does not have a resistor between the Input Protection Circuit PCB and the Deflection PCB.
Deflection PCB does _not_have Version 4 capacitors C804 and C805 (below top center of PCB) or an Input Protection Circuit PCB installed.
- Perform the appropriate procedure for the version of Wells-Gardner display determined from Table 3. (Refer to the Wells-Gardner display manual, TM-183, for camponent and connector locations.)
The 30 k2, 1/4 W resistor supplied in the kit is used only for Version 1 of the Wells-Gardner display. Major Havoc Conversion Instructions
Solder the cathode lead of a type-1N4002 diode to pin 5 and the anode
Major Havoc Conversion Instruct ions ‘TM-268
Version 1
Perform the following procedure for Version 1 of the Wells-Gardner display.
- Verify that the Preliminary Procedure has been performed.
- Use a soldering iron to remove resistor R811 and replace it with the 30 k2, 1/4 W resistor supplied in the kit.
Version 2
Perform only the Preliminary Procedure for Version 2 of the Wells-Gardner display.
Version 3
Perform the following procedure for Version 3 of the Wells-Gardner display.
- Verify that the Preliminary Procedure has been performed.
2. Locate the wire connected to resistor Rl (22 k) and the collectors ®
of transistors Ql and Q3 (type 2N3904) on the Input Protection Circuit PCB and the point shown in Figure 7 on the Deflection PCB.
- Use a wire cutter to cut the wire, located in step 2, midway between the two PCBs.
- Use a soldering iron to solder a 1 k, #5%, 1/4 W resistor (not included in the kit) between the two ends of the wire cut in step 3.
Version 4
Perform the following procedure for Version 4 of the Wells-Gardner display.
This version of the display requires that an Input Protection Circuit PCB assembly be installed on the ‘ Deflection PCB as part of the display modification procedure. This PCB assembly is not included in the kit. However, to obtain the Input Protection Circuit PCB assembly, use the order form at the back of this document.
‘TM-268 Major Havoc Conversion Instructions
Verify that the Preliminary Procedure has been performed.
Install the Input Protection Circuit PCB to the Deflection PCB as described in the instructions supplied with the Input Protection Circuit PCB assembly.
I. MODIFY THE AMPLIFONE DEFLECTION PCB
The following procedure applies to those Space Duel, Gravitar, and Black Widow games that use an Amplifone display. If your game has a Wells-Gardner display, perform "H. Modify the Wells-Gardner Deflection PCB".
Perform the following procedure to modify the Amplifone Deflection PCB (see Figure 8).
- Set the Deflection PCB on a clean work surface.
- Connect two type-1N754A Zener diodes together, anode to anode, as shown in Figure 6. Use a soldering iron to solder the two anode leads together.
- Connect two type-1N756A Zener diodes together and solder as described in step 2.
- On the camponent side of the Deflection PCB, locate the yellow wire connected to resistor Rl (left center of the PCB).
- Solder one cathode lead of the two type-1N754A Zener diodes (soldered together in step 2) to the yellow wire on the soldered side of the Deflection PCB as shown in Figure 8.
- Solder the other cathode lead of the two type-1N754A Zener diodes to the nearest ground on the PCB as shown in Figure 8.
- On the camponent side of the Deflection PCB, locate the orange wire connected to resistor R24 (right center of the PCB).
TM-268 Major Havoc Conversion Instructions
fe] s N < $ z 1N4002 Diodes
1N756A Zener Diodes 1N4002 Diodes
Figure 8 Modifying the Amplifone Deflection PCB
‘T™M-268
10.
ll.
12.
13.
14.
15.
16.
17.
Major Havoc Conversion Instruct ions
Solder one cathode lead of the two type-1N756A Zener diodes (soldered together in step 3) to the orange wire on the soldered side of the Deflection PCB as shown in Figure 8.
Solder the other cathode lead of the two type-1N756A Zener diodes to the nearest ground on the PCB as shown in Figure 8.
On the soldered side of the Deflection PCB, solder the cathode lead of a type-1N4002 diode to the emitter of transistor QL7 as shown in Figure 8.
Scrape away the green protective coating at a convenient point on the PCB, and solder the anode lead of the type-1N4002 diode to the collector of transistor Q17 as shown in Figure 8.
On the soldered side of the Deflection PCB, solder the anode lead of a type-1N4002 diode to the emitter of transistor Q16 as shown in Figure 8. :
Scrape away the green protective coating at a convenient point on the PCB and solder the cathode lead of the type-1N4002 diode to the collector of transistor Q16 as shown in Figure 8.
On the soldered side of the Deflection PCB, solder the cathode lead of a type-1N4002 diode to the emitter of transistor Q7 as shown in Figure 8.
Scrape away the green protective coating at a convenient point on the PCB and solder the anode lead of the type-1N4002 diode to the collector of transistor Q7 as shown in Figure 8.
On the soldered side of the Deflection PCB, solder the anode lead of a type-1N4002 diode to the emitter of transistor Q6 as shown in Figure 8.
Scrape away the green protective coating at a convenient point on the PCB and solder the cathode. lead of the type-1N4002 diode to the collector of transistor Q6 as shown in Figure 8.
Major Havoc Conversion Instructions TM-268
Wire Ties
Cable Tie Mounts Metal Tab
Player Start Switches (see diagram below for wire connection information)
Pushbutton Leaf Switches’
To 12-Pin Harness Connector J24
Player-Start Switch Existing Control- Reference Diagram Panel Hamvess,
*See the control panel wiring diagram included in the kit for the proper Tap Splicer Installation colors of the wire connections from the contro!-panel harness (included in the kit) to the existing harness, and the control panel switches,
Figure 9 Modifying and Installing the Control-Panel Harness —)
)
t
T™M-268 Major Havoc Conversion Instruct ions
J. MODIFY THE CONTROL-PANEL HARNESS
Perform the following procedure to modify and install the Space Duel, Gravitar, or Black Widow control-panel harness (see Figure 9).
- Use pliers to attach the tap splicers and connect the violet, black, red, and blue wires fram connector P52 (included in the kit) to the appropriate wires of the existing control-panel harness. Refer to the control-panel wiring diagram (included in the kit) and Figure 9 for the proper harness-wire connections to connector P52 and to the control-panel switches.
- Black Widow Only. Remove the white/gray wire fram pin 9 of connector J24A and reconnect it to pin 5 of the 12-pin connector J24A. (If available, use an extraction tool, AMP part no. 458994-1).
- Connect the modified control-panel harness to the Major Havoc control panel as shown in Figure 9. Make certain that: (1) the green ground wire is securely attached to the metal tab on the control panel; (2) the wire ties and cable tie mounts (included in the kit) are installed; and (3) the excess wire is securely and neatly tied to prevent the excess and unused wires fran contact with the controlpanel switches when the control panel is closed.
K, MODIFY THE REAR ACCESS PANEL
Perform the following procedure to modify the rear access panel to provide a fan intake opening (see Figure 10).
- Measure and mark the rear access panel for locating the fan intake opening as shown in Figure 10.
- Use an electric hand drill with a 1/4-inch bit to drill holes in the rear access panel at each corner of the marked fan intake opening.
- Use a sabre saw to cut the wood fran the fan intake opening.
Major Havoc Conversion Instructions TM-268
Rear Access Panel
Alr Flow Direction Arrow
2%-Inch Self-Tapping Screws.
Fan-Blade Guard
Exhaust Fan
Figure 10 Modifying the Rear Access Panel and Installing the Fan
T-268 Major Havoc Conversion Instruct ions
ASSEMBLY INSTALLATION INSTRUCTIONS
The following procedures describe the installation of the Major Havoc assemblies.
L. INSTALL THE SIDE-PANEL DECALS (OPTIONAL)
The Major Havoc side-panel decals are not included in the kit. However, if you wish to purchase these decals, use the order form provided at the back of this document.
Perform the following procedure to install the Major Havoc side-panel decals on the game cabinet (see Figure 11).
- Mix a normal solution of any liquid dishwashing detergent and approximately three quarts of water in a bucket.
- Clean all oil, film and dust fram the sides of the cabinet. Fill any dents or gouges with a filler material.
We recommend that the following procedure be performed by two persons. One person may have difficulty handling the cabinet and the large decals.
- Tip the game cabinet and gently lay one side on a blanket.
- Use a sponge to liberally apply the water and detergent solution over the entire side of the cabinet.
- Grasp the top edge of the appropriate decal for the side of the cabinet. Hold the decal up and off of the floor and peel away the protective backing.
Major Havoc Conversion Instruct ions TM-268
‘Side-Panel Decal
Trim carefully along edge X-ACTO™ Knife
Press down working outward from center Align decal with rear and bottom edges of cabinet
Figure 11 Installing the Side-Panel Decals
TM-268
10.
ll.
12.
Major Havoc Conversion Instruct ions
Align the decal with the rear and bottom edges of the cabinet as shown in Figure 11.
After the decal is in position, use the squeegee to remove all the excess water and detergent fram beneath the decal by quickly working fran the center to the outside edges. HINT: If any air bubbles form, puncture them with a pin or the tip of an X-ACTO™ blade. Rub gently with a soft cloth to disperse the trapped air.
Carefully insert a #11 X-ACTO™ blade (or suitable substitute) between the T-molding and cabinet wall and, following the contour of the cabinet, cut off the excess decal. Rub the cut edges with a cloth to smooth down any rough edges.
When the wrinkles are removed and the decal is free of all excess water and detergent, gently turn the game cabinet over to the opposite side. Be careful to avoid damaging the freshly applied decal.
Repeat steps 2 through 8 for the remaining decal.
Carefully raise the cabinet to the upright position.
Use a lint-free cloth to wipe off any excess water and detergent fron inside and outside of the cabinet. Allow time to dry before proceeding.
M, INSTALL THE ATTRACTION PANEL
Perform the following procedure to install the Major Havoc attraction panel in the game cabinet (see Figure 1).
1. Fram the front of the cabinet, install the Major Havoc attractionpanel film and glass into the bottam retainer.
Use a 1/8-inch Allen wrench to secure the top retainer to the game cabinet.
Press the bottom retainer tight against the attraction-panel glass.
Use a 1/8-inch Allen wrench to tighten the three screws securing the bottan retainer to the game cabinet.
Major Havoc Conversion Instructions ‘TM-268
N. INSTALL THE WELLS-GARDNER DEFLECTION PCB
Perform the following procedure to install the modified Wells-Gardner Deflection PCB on the display chassis (see Figure 3).
1.
2.
oO. Fran the rear of the game cabinet, slide the Deflection PCB into the front retaining bracket on the chassis.
Use a 1/4-inch hex driver to install the two screws and washers securing the modified Deflection PCB to the display chassis.
Make certain that the harness fran Q705 and Q706 is connected to P700 and NOT to P100.
Attach the 15-pin Molex connector to the chassis bracket and connect the 15-pin mating connector.
Connect the Neck PCB connector to the Neck PCB (P500).
Connect the remaining nine connectors to the appropriate plugs on the Deflection PCB. The single wire connectors have the wire color labeled beside the mating pin on the PCB.
INSTALL THE AMPLIFONE DEFLECTION PCB
Perform the following procedure to install the Amplifone Deflection PCB in the game cabinet (see Figure 3).
1. Fram the rear of the cabinet gently slide the modified Deflection PCB into the slotted cleats. Make certain that the components soldered to the back of the board clear the cabinet wall.
Use a Phillips screwdriver to secure the PCB to the cabinet with the screw and spacers removed previously.
Connect the four harness connectors to the Deflection PCB.
T™M-268 Major Havoc Conversion Instruct ions
P. INSTALL THE CONTROL PANEL
Perform the following procedure to install the Major Havoc control panel in the game cabinet (see Figure 2).
- Use a 7/16-inch hex driver to secure the control panel to the cabinet with the three bolts, washers, and nuts removed previously.
- Connect the control~panel harness connector to the game harness. Do not close the control panel.
Q. INSTALL THE MAJOR HAVOC PCBs
Perform the following procedure to install the Major Havoc PCBs in the game cabinet (see Figure 12).
- Peel the protective backing fran the 1-1/8-inch thick foam pad supplied in the kit.
- Fram the front of the cabinet, reach in through the control-panel opening and attach the foam pad to the front wall of the cabinet approximately midway between the upper and lower slotted PCB guides.
- Connect the Conversion PCB to the Major Havoc game PCB edge connectors.
Do not over-tighten the tie wraps to the printedcircuit boards. If the tie wraps are too tight, the Conversion PCB could bow and cause a faulty contact at the edge connectors.
- Use tie wraps at each end of the PCBs to secure the Conversion PCB to the Major Havoc PCB.
Before installing the Major Havoc printed-circuit boards in the cabinet, be sure the option switches are set for the desired game options. See Chapter 1 in the Major Havoc operators manual (TM-252).
Major Havoc Conversion Instructions TM-268
Ya-Inch Foam Pad
Tie Wrap
PCB Mounting Bracket
Game PCB
e ]
1 %-Inch Foam Pad
Conversion PCB Tie Wrap
Figure 12 Installing the Major Havoc PCBs
‘T™M-268
10. Major Havoc Conversion Instruct ions
Slide the Major Havoc PCB (with the Conversion PCB attached) into the slotted cleat.
Attach the 1/2-inch thick foam pad approximately l-inch fran the top of the Conversion PCB.
Position the PCB mounting bracket in the center of the 1/2-inch thick foam pad and press firmly against the pad.
Check that the back edge of the Major Havoc PCB is pressed firmly against the 1-1/8-inch foam pad installed in step 2. Use a Phillips screwdriver to secure the PCB mounting bracket to the cabinet with the pan-head screw.
Connect the top and bottam connectors on the main harness to the Conversion PCB.
Use beaded tie wraps at each end to secure the two edge connectors to the Conversion PCB.
R._ INSTALL THE POWER SUPPLY
Perform the following procedure to install the modified power supply into the game cabinet.
1. Use a Phillips screwdriver to secure the power-supply base plate and power supply to the cabinet floor with the four screws removed previously.
Connect the game harness to connectors J2, J4A, and J5 on the top of the power supply.
Connect the power cord to connector Jl on the right side of the power supply.
Use a 11/32-inch hex driver to secure the green ground wires to the grounding screw on the power supply with the washer and nut removed previously.
S. INSTALL THE FAN
Perform the following procedure to install the fan in the game cabinet (see Figure 10).
1. On the inside of the rear access panel, position the fan-blade guard over the fan opening.
Major Havoc Conversion Instructions T™M-268
- Place the exhaust fan on the fan-blade guard with the arrow on the fan housing pointing toward the inside of the cabinet.
- Use a Phillips screwdriver to install the four self-tapping screws which will secure the exhaust fan and guard to the rear access panel.
- Connect the black and white wires on the fan harness to the two fan power-input terminals.
- Use a Phillips screwdriver to secure the green wire to the fan frame with the self-tapping screw.
- Connect the fan harness to connector J4B on the power supply.
T. INSTALL THE SELF-TEST CHART
Staple or tape the Major Havoc self-test chart to the inside of the rear access panel.
U. INSTALL THE LABELS
Do not remove or mark any of the existing labels on the game cabinet.
Perform the following procedure to install the conversion kit and FCC com pliance labels on the game cabinet (see Figure 13).
- Remove the protective backing fram the conversion kit and the FCC campliance labels.
- Attach the conversion kit label to the back of the game cabinet directly above the rear access panel.
a If your game has an FCC label, attach the FCC compliance label included in the kit directly OVER the existing FCC label. If not, attach the FCC compliance label included in the kit next to the conversion kit label directly above the rear access panel.
ob TM-268
Major Havoc Conversion Instruct ions
in Part 15 of FCC A computing deequipme
FCC Compliance Label Install over the existing FCC Non-Compliance Label
CONVERSION KIT 1265 Bor nue ATARI Sunnyvale, CA 94086 USA
Conversion Kit No.)
Serial No. |
120 Volts 60 Hz
Conversion Kit Label
Figure 13 Installing the Labels
Major Havoc Conversion Instructions 'TM-268
V._INSPECT THE MAJOR HAVOC GAME
Before applying power, perform the following procedure to ensure that the game is modified correctly.
1.
2. Carefully check that the conversion has been properly performed.
When you are confident that all instructions were properly followed, close and lock the rear access panel.
Reach up through the coin-door Opening and latch the two spring-draw latches to the control panel.
Plug in the game power cord and turn the game on,
Set the game self-test switch to the on position and perform the self-test procedure in the Major Havoc operators manual (TM-252) .
W. ADJUST THE DISPLAY
Perform the following procedures to adjust the display size, centering, linearity, brightness, and color tracking.
X/¥ Center, Size, and Linearity
1. Set the game self-test switch to the on position and obtain Screen 5, Diagonal Crosshatch display.
The horizontal (X) adjustments are located on the Conversion PCB (see Figure 14) and the vertical (Y) adjustments are located on the Major Havoc game PCB (see Major Havoc operators manual). The X adjustments on the Major Havoc game PCB are bypassed through the Conversion PCB and are not functional when the Conversion PCB is connected.
Adjust the X and Y SIZE and CENTER controls so that the white rectangle fills the screen with the corners visible while the red rectangle corners are off the screen.
‘T™268
Major Havoc Conversion Instruct ions
Figure 14 Adjusting the Display
Major Havoc Conversion Instruct ions TM-268
- Adjust the X and Y LINEARITY controls for the straightest possible diagonal lines in the Diagonal Crosshatch display.
- Repeat step 2 and 3 until the straightest possible diagonal lines are obtained (the linearity and size adjustments are interactive).
Brightness
Perform the following procedure to adjust the display brightness.
- Set the game to the Self-Test Mode and obtain Screen 6, Color Intensity Test display. See the Major Havoc operators manual for a description of self-test operation.
- Adjust the SCREEN BRIGHTNESS control to make the longest white line visible and the white line above the longest line not visible. See the display manual for the location of the SCREEN BRIGHTNESS control.
Tracking
Perform the following procedure to evaluate and adjust the white tracking.
- Set the game to the Self-Test Mode and obtain Screen 6, Color Intensity Tegt display. See the Major Havoc operators manual for a description of the self-test operation.
- Verify that the middle five or six lines are white and remain white as the intensity progresses fran dim to bright (top line campared to bottom line). If not, perform the tracking adjustment procedure in the display manual.
X, SET THE OPTION SWITCHES
Verify that the option switches are set to the desired play options for your location. The recommended play options are 2 coins for 5 starting lives, medium difficulty, and bonus life for 100,000 points. Refer ta the Major Havoc operators manual for option switch location and setting information.
Y. UPDATE THE GAME DOCUMENTATION
We suggest that you keep this document and CO-252-03 for conversion kit parts information. Keep the control-panel wiring diagram (included in the kit) as part of the Major Havoc schematic package (SP-252).
TM-268 Major Havoc Conversion Instructions
Change your Wells-Gardner display manual (TM-183) schematics as shown in Figure 15 (for Versions 2, 3, and 4), Figure 16 (for Versions 2, 3, and 4), or Figure 17 (for Version 1). Change your Amplifone display manual schematics as shown in Figure 18 for TM-194 or as shown in Figure 19 for TM-239.
TM-268
Major Havoc Conversion Instruct ions
xower a ---
& zak +27vV——
cri nia. sv
YINpuT —-------
: £ baz [conamiousansnents [ er | —“
Bore zo mga Beas 5700
a Te Reo! Low Rs 2yve Vee (ye as
2NB904
25V
as zee
Components outlined by shaded frame have been added per TM-268.
Figure 15 Input Protection Circuit Schematic (Versions 2, 3, and 4)
C ‘T™-268
Major Havoc Conversion Instruct ions
DEFLECTION PCB Pata ae
|. Resistance values in ohms, % watt, 25%, un Jess otherwise noted. K = 1,000, M = 1,000,000 . Capacitance value of 1 or less is in microFarads, above 1 in picoFarads, unless otherwise noted.
- 2900 and 906 are not in High-Voltage PCB.
Components identified by shading have special characteristics important to safety and should be replaced only with identical types. GENERAL NOTES
- AN D.C. voltages are + 10% measured from point indicated to ground, using a high-impedance meter. Voltages are measured with no signal input and controls are in a normal operating position.
- Circled numbers indicate location of waveform reading.
Components outlined by shaded frame have been added per TM-268.
- ZD100-101 uses (66X0040-007) zener diode in series with (340X2331-934) 330-ohm resistor in Production models. arty
- Use a 1,000:1 probe when measuring G2 (screen) ‘or focus voltage.
Figure 16 Wells-Gardner Deflection PCB Schematic (Versions 2, 3, & 4)
Major Havoc Conversion Instructions TM268
ror anus
DEFLECTION PCB
racer pur come] °O ate na eaeori|
Hi
GENERAL NOTES 1, Resistance values in ohms, %4 watt, +5%, un fess otherwise noted. K = 1,000, M = 1,000,000
- Capacitance value of 1 or less is in microFarads, above 1 in picoFarads, unless otherwise noted.
- *Q900 ana Q906 are not in High-Voltage PCB.
- AILD.C. voltages are = 10% measured from point indicated to ground, using a highimpedance meter. Voltages are measured with no signal input ‘and controls are in a normal operating position,
- Circled numbers indicate location of waveform reading. |. ZD100-101 uses (66X0040-007) zener diode in series with (340X2331-934) 330-chm resistor in early production models. Use a 1,000:1 probe when measuring G2 (screen) or focus voltage.
Components identified by shading have special characteristics important to safety and should be replaced only with identical types. | a | Components outlined by shaded frame have been added per TM-268.
Figure 17 Wells-Gardner Deflection PCB Schematic (Version 1)
TM268 Major Havoc Conversion Instructions
Q3 az 2N3904 TOK i”
Qe 2N3 984
t CRe RTA aw i}Posistor |2 cree IN4001
Components identified by shading have special characteristics important to safety and should be replaced only with identical types. C | Components outlined by shaded frame have been added per TM-268. Figure 18 Amplifone Deflection PCB Schematic for TM-194
Major Havoc Conversion Instructions TM-268
R23 See a? SBR ww
JIGS. PBS REI » BP Woe. Lee? Beans R74 Py Poston [2 $2 [O [ 4 ee, oe CR22 ' Gea HRRBRBA components dentitied by shading have special characteristics importantto safety and should be replaced only with identical types.
CEE Components outlined by shaded frame have been added per TM-268. ®
Figure 19 Amplifone Deflection PCB Schematic for TM-239
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply
Name
Firm Q Distributor
Address © Operator City State Zip O Other
Area Code Phone 'T™M-268
‘Tape This Edge
First Fold
No postage necessary if mailed in the United States
POSTAGE WILL BE PAID BE ADDRESSEE
Atari Inc. Attn: Customer Service/Coin-Op Division 737 Sycamore Drive P.O. Box 906 Milpitas, California 95035
Second Fold
From:
‘TM-268
To Receive a Free
Input Protection Circuit PCB Assembly
If you have a Wells-Gardner display in your cabinet, the Input Protection Circuit PCB Assembly is required for your Major Havoc™ game. This small “piggy-back” board was not included in your Conversion Kit when the kit was shipped to you.
However, if you need this board, mail this letter to Atari Customer Service and they will send you the Input Protection Circuit PCB Assembly at no charge. No postage stamp is necessary if mailed in the U.S.A.
The part number of the board is A038088-01.
Game Serial No. that was shipped with your kit
Name
Firm
Address
City State Zip
Area Code Phone
Distributor O Operator Other
TM-268
To Receive a Free Set of
Multi-Color Side-Panel Decals
The multi-color side-panel decals for your Major Havoc™ Conversion Kit were not included when the kit was shipped to you. However, if you wanta set, mail this letter to Atari Customer Service and they will send you these decals at no charge, while supplies last. No postage stamp is necessary if mailed in the U.S.A.
The part numbers of the decals are: Left—042421-01, and right—042421-02.
Game Serial No. that was shipped with your kit
Name
Firm
Address
City State Zip
Area Code Phone
O Distributor O Operator Other
Kit Warranty
Seller warrants that its electronic parts supplied in this kit are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the electronic parts supplied in this kit fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such electronic parts which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Seller’s plant; and
- Seller’s examination of said products discloses to Seller's satisfaction that such al- . leged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. Inno event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of ‘merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.