Thunder Jaws TM-349 1st Printing
ThunderJaws (rev 3) (Atari Games, 1990) · Technical Manual · 56 pages · 47 sections · original scan
AQ 1st printing
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAMES
Thunderaws
Universal Kit Installation Instructions
Copyright © 1990 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, California 95036-1110
Printed in the U.S.A 5/90
Produced by the Atari Games Technical Publications Department. Technical Writing and Design: Andrea Dencker Illustration: Mary Ohanessian Sumner ThunderJaws Universal Kit
Notice Regarding Non-Atari® Parts
‘You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: Substitute non-Atari parts in the game.
- Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
- The power cord is properly plugged into a grounded three-wire outlet. © On games provided with an Electromagnetic Interference (EMD ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area,
‘ThunderJaws Universal Kit
Contents
1 Installation How to Use This Manual .... Cabinet Equipment Requirements Tools Required... Inspecting the Kit Preparing the Cabinet for the Kit Installation Assembling the Control Panel. Connecting the JAMMA Harness. Installing the ThunderJaws Game PCB Installing the Bezel, Labels, Decals, and Attraction Assembly Setting the Coin and Game Options. Game Play... 2 Self-Test Entering and Exiting the Self-Test Select Test Menu 2-2
2-2 2-3
2-3 Coin Options. Sound Board Tes Switch Test..... 24 Complete RAM Test 2-5 Complete ROM Test 2-6 2-6 2-6 2-6 2-6 Dual Playfield Test.. Motion Object Test Alphanumerics Test Color Test... Color Purity Test 2-7 Convergence Tes! 27 3 Maintenance and Troubleshooting Video Display. we BB Joystick Assembly 3-3 ROMs and RAMS. 3-4 4 Parts Illustrations See the list of illustrations that follows.
5 Schematics See the list of illustrations that follows.
ThunderJaws Statistics Sheet
Warranty Figure 1-1 1-2
1-3 Figure 2-1 2-2
2-4
2-6
2-8
2-10 2-11 2-12 2-13 2-14
Figure 3-1 Figure 4-1 4-2
4-4
Figure 5-1
5-2
Table 1-1 1-2
Table 2-1 2-2 2-3 2-4
Table 3-1 3-2
3-3 3-4 Illustrations
Assembling the Control Panel... Thunderjaws Kit Parts Installed in a Cabinet Control Panel Template... Select Test Menu Screen. Statistics Screen.
Sound Test Screen. Switch Test Screen Complete RAM Test Screen Complete ROM Test Screen. Dual Playfield Test Screen. Motion Object Test Screen .. Alphanumerics Test Screen Color Test Screen Color Purity Test Screen. Convergence Test Screen Maintaining the Joystick Assembly ThunderJaws Kit Parts List..... Microswitch Joystick Assembly . ThunderJaws Game PCB Assembly .. JSA Audio II PCB Assembly ThunderJaws Game PCB Assembly Schematic Diagram JSA Audio II PCB Assembly Schematic Diagram
Tables
Equipment Requirements Kit Contents List...... JAMMA Pin and Wire Connections Summary of the Self-Test Screens Game Option Setting: Coin Option Settings. When to Run the RAM Test Bad RAM Location by Error Address. Bad ROM Location by Error Address. Troubleshooting Table.. Voltage Inputs and Test Points on the PCBs What ROM Problems Look Like............ 3-3 Atari Games Video Connector Pin Assignments.... Color Assignments for RAM Errors Encountered
iti
‘ThunderJaws Universal Kit
Safety Summary
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.
iv Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
CHAPTER 1
Installation
How to Use This Manual
This manual provides infor-
mation for installing, testing,
and troubleshooting the ThunderJaws™ Universal kit. The manual is divided
into the following chapters:
m Chapter 1 describes how to install the ThunderJaws kit in your cabinet and the
ThunderJaws game play. Also included is the template for drilling the holes into the control panel. m Chapter 2 describes the self-test and how
to use the self-test screens.
m Chapter 3 contains troubleshooting and mainte-
nance procedures. ™ Chapter 4 contains parts illustrations and the kit
parts list. m Chapter 5 contains the schematics
for the ThunderJaws game PCB and JSA
Audio II PCB.
Installation.
Cabinet Equipment Requirements Table 1-1 lists the equipment required in the cabinet into which you are installing the ThunderJaws kit.
Table 1-1 Equipment Requirements
. Specification ° «Color RGB monitor. Separate positive horizontal and ve “cal sync or negative composite sync ~ Horizontal mounting = ‘Horizontal frequency: 15.750-KHz_ Vertical frequency: 60 Hz‘ Video input: 1V to 3V peak-to-peak Equipment: Video Display
positive polarity :
| Control Panel | Metal only | : |
| | Speaker | 8Q, 5 Worlow | ! |
| Coin Counter | 45 VDC or +12 VDC | i |
Mechanism “~~ wi ius |
| Power Cord | ‘Three-conductor with ground | i |
| Power Supply | +5 VDC + 0.25V @ 3.0 amps | i |
+12 VDC @ 1.0amp.*. - ~5 VDC @.1.0 amp (Optional)
Tools Required = Two C-clamps m = Drill with a 1/4-inch drill bit, a 1 3/4-inch hole cutter (or a 1 3/4-inch chassis punch), and a 1 3/16inch hole cutter (or a 1 3/16-inch chassis punch) Phillips screwdriver Flat-blade screwdriver Socket wrench set and ratchet ‘ThunderJaws Universal Kit
1/4-20 hex wrench Wire cutters and strippers Straight edge Squeegee X-ACTO™ knife Fast-ons (if you are installing a new JAMMA harness)
Inspecting the Kit Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the ThunderJaws kit serial number, part number and description of the missing or damaged parts, and date received.
Table 1-2 Kit Contents List
Part No. 038158-01 039450-01. 047205-01
047806-01 047806-02. 047807-01
047809-01 141026-001
178237-001'""* 178237-005'-
178283-003 178283-004 72-6612S
ThunderJaws Universai Kit
Preparing the Cabinet for the Kit Installation
- Turn off power to the game.
- Remove the following from the cabinet: m Old PCB(s). m Game harness, if it is not Japan Amusement Machinery Manufacturers Association GAMMA)compatible. ™ Control panel decals, labels, and controls. m Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals, m Video display shield, display bezel, attraction shield, and marquee.
- Wipe down and vacuum the cabinet. Paint the cabinet, if required,
047209-01 Control Panel Cover
178237-008 Blue Button ‘Assembly (2 places) Installation
Assembling the Control Panel To assemble the control panel, you need a copy of the installation template (see Figure 1-3) and the following parts from the kit: Clear cover for the control panel Control panel decal Two blue buttons Two red buttons Four snap-action switches Two “START/FIRE” button indicator plates Two “JUMP” button indicator plates Two joystick assemblies Twelve #10-24 x 1-inch-long carriage bolts, flat washers, and locknuts
- Measure your control panel to find out what size the decal and cover should be. Cut the control panel decal and cover to fit.
75-5112B | —#10-24 x 3/4" Carriage Bolt
A040933-03 8-position ;_doystick Assy
erogeend 178283-003 SUMP Indica- STARTFIRE 047805-01 poles v Control Panel Decal - a Indicator Plate
i+ 175014-1040 #10 Flat Washer 177010-240 478287-001 #10-24 Hex Locknut Red Button Assembly (2 places)
Figure 1-1 Assembling the Control Panel
1-3
Installation
- Clamp the control panel cover to the control panel.
- Drill four comer holes through the control panel and the control panel cover. Use a 1/4-inch drill bit. 4, Install four carriage bolts and locknuts through the holes to hold the cover and the control panel together.
- Cut the holes in the cover and panel using a 1 3/16-inch hole cutter for the button holes and a 1 3/4-inch hole cutter for the joystick knob holes. ‘ThunderJaws Universal Kit
Use a 1/4-inch drill bit to drill the mounting holes for the joysticks. . Disassemble the control panel and the control panel cover. . Install the control panel decal on the control panel. Use a sharp knife and cut out the holes for the controls in the decal. . Install the cover on the control panel with four carriage bolts, washers, and locknuts.
Table 1-3 JAMMA Pin and Wire Connections
If your « ‘coin’ ‘counter(s)
_ Use this wire if you wai
Connect to the +12V t terminal of 1e por
est switch on the PCB. (fy ne an excrna 5 the PCB, Connect the wire to ihe? -N-O- terminal onthe common terminal of the switch ue a BR he (GND,
Connect this wire to the N. O. terminals of the left FIRE/ mon‘terminals of the'switches to one of the BK/W wi Connect this wire to the N.O. a minal of the switch to ‘one of
Thunderjaws Universal Kit Installation
Table 1-3 JAMMA Wire Connections, Continued
GY ~~ Not used Not used ct OF the power supply Gf it exists) and one to the common termi Connéct't two of these wires to the’ common terminals <
Connect t6'the -5V terminal
12V. RIN or the 5 iM RIN (GND,
“MIPPCB if you'use'a second ‘coin’ counter. Note: Do noi If your counter ‘requires 5V, ‘connect a:wire from’ Also clip R24-on the game PCB. oe tee Co aa Ee
Not used GREEN = COMPSYNC:.. Attach 'to the video ee i _ Not used Not uséd' cue ‘ “RT COIN Connect to the N.O. terminal of the tig! i sev the:switch to a BK/W wire. Not used) 22% VIB Y/BN RT. JOYST UF “Connect to the N.0. ‘terminal S tovone of the BK/W wires? R Sots DN’ Saine as pin V!
z ect two of these wires to ‘the ‘common terminals of thy
ee panel. ssp itr bin aia £93 BK/W. GND” Same as pit e.*
Installation
- Install the buttons with the “START/FIRE” or “JUMP” indicator plate under each button. Install the blue player control buttons on the left and the red player control buttons on the right. (See Figure 1-1.) Install the joysticks with the carriage bolts, washers, and locknuts.
Connecting the JAMMA
Harness
- If your game does not already have a JAMMA harness, install the JAMMA harness in the cabinet.
- Install the split beads on the JAMMA harness as close to the edge connector as possible. Hold the beads on the harness with the tie wraps included in the kit. ‘ThunderJaws Universal Kit
Connect the wires designated for the red, green and blue video guns along with the sync and ground wires, according to Table 1-3. Connecting Coin Door Wires
- Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.
- Connect one terminal of the door lamps to one of the BK/W wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
- Using Table 1-3, JAMMA Pin and Wire Connections, for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.
Connecting Power Wires
. Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The ThunderJaws kit requires +5V and +12V. If -5V is available, it should be used too. Tie off any other voltage wires on the power supply besides +5V, - SV, and +12V. There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-
- so that the edge connector does not overload and burn.
Connecting Video Display Wires
1-6 Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply. Connecting the Control Wires Connect the joystick harnesses and the button harnesses to the JAMMA harness according to the information in Table 1-3.
Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the video display, and the power supply. This is required for the safety of the players. This AC ground must be of #18 AWG wire or larger. Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and —5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.
Installing the ThunderJaws
Game PCB
- After you have checked the power on the JAMMA connector, above, install the ThunderJaws game PCB in the cabinet. Use the nylon standoffs and four #6-32 screws in the kit.
- Connect the JAMMA connector to the PCB.
- Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 3.
ThunderJaws Universal Kit
- Bundle the loose wires together with tie wraps, and secure all wiring harnesses away from the PCB.
Installing the Bezel, Labels, Decals, and Attraction Assembly
The kit parts are shown assembled in a cabinet in Figure 1-2.
Installing the Display Bezel Find the cardboard display bezel (part no. 047809-01). Measure the size of the existing display bezel and cut the new display bezel to size, if necessary. Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC label (part no. 039450-01) on the back of the cabinet.
Installing the Side Panel Decals Find the side panel decals. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1-2. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry. Installing the Attraction Assembly Find the ThunderJaws attraction shield and the attraction film. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-2.
Setting the Coin and Game Options
Set the coin and game options in the self-test. See Chapter 2 for information about the option settings.
Game Play
This section of the manual describes the theme of the ThunderJaws game and the game play features. Introduction : The beautiful, brilliant, but quite insane Madam Q has devised a plot to destroy the surface of the Earth and leave her underwater city intact. She has created an army of genetically mutated humans and bionic warriors to protect her labs, bases Installation.
and city and to carry out her mad schemes. You are a member of a underwater special forces unit and have been selected to infiltrate Madam Q’s headquarters and stop her demented plans before she can destroy the world. The only known operation of Madam Q’s vast underwater empire is a research station located on Paradise Island in the South Pacific. You will be taken there to begin your mission. You are directed to take this sta~ tion, shut it down, and learn as much as possible about the whereabouts of other parts of Madam Q’s empire...good luck!
One or two players can enter the game at any time with ThunderJaws’ buy-in and game continuation features. In a one-player game, if a player “dies”, he can add coins to continue, and he will be restarted at the last checkpoint completed. To start or continue a twoplayer game, the second player will be flown in on a jet pack to join (or rejoin) player one. Controls consist of one eight-position joystick and two buttons per player (“Fire/attack” and “Jump”). In the swimming mode, Fire shoots the current weapon and Jump gives an extra flipper boost. In the surface waves the player is in a walking mode and the controls have a variety of movements. Fire shoots the current weapon or attacks the enemy handto-hand. Fire with the joystick in the up position will fire the weapon at a 45° angle upwards. On the surface levels, the Jump button allows the player to jump over objects to the left or right. With the joystick in the up position, Jump will make the player jump higher and reach upper walkways; with the joystick down, the player can jump to lower walkways. The joystick can also be used in front of levers to activate playfield animations and to climb up and down ladders. Players can retrieve air tanks (in the water) and firstaid kits (on the surface) for extra health. Flashing special weapons can provide extra fire power. The special weapons include the Uzi, Flamethrower, Super-Seeker, Explosive Bolt, and Triple Shot. As the game begins, players are dropped off underwater by a mini-sub outside a coral reef which borders Paradise Island, Players must fight Madame Q's divers and cybernetic sharks that guard the entrance to her lab. Upon gaining entrance to the underwater city, players shed their scuba gear and find themselves
1-7
Installation
047205-01 Attraction Shield
047807-01 [Attraction Film
047809-01 ° Bezel with Graphics “
, ) ThunderJaws Universal Kit
72-6612S #6 x 3/4" PH Screw
047806-01 Side Panel Decal
Self-Test Volume Switch — Control
A047872-01
047209-01 75-5112B Control Panel Cover "10-24 x 3/4"
Carriage Bolt
178237-008 Blue Button Assy (2 places)
. 178283-004 —178283-003 Control Panel Jump Indicator ——StarvFire Plate Indicator Ptate
175014-1040 #10 Flat Washer 178237-001 177010-240 Red Button Assy #10-24 Hex (2 places) Locknut
Figure 1-2 ThunderJaws Kit Parts Installed in a Cabinet
1-8 ‘Thunderjaws PCB Board Set 178265-001 L-Shaped Nylon Standofts 72-6128 #6 x 3/4" PH Screw
ThunderJaws Universal Kit Installation
‘Top edge of control panel (closest to monitor). Right half of control panei
O O
i Red button Jump")
Red button ("StervFire”) OOeeeeeeeeeeen +
Joystick O L]
Top edge of control panel (closest to monitor). Left half of controt panei
Blue button
- (“Jump”)
Blue button ('StarvFire")
Joystick O C]
Figure 1-3 Control Panel Template
Installation
in Madame Q's lab. The transformation tank where Madame Q creates her soldiers can be seen in the background as players fight Bionic Guards, Bionic Wolves, and other creatures. In the lab, players must find and rescue the beautiful human captives before they are converted into more mutant soldiers. The captives saved, players then swim underwater through the treacherous toxic waste dump to search for Madame Q. Their quest takes them to the infrastructure of the oil drilling platform, down into the bowels of the geothermal power plant, through the underground volcano, to a control room, into the underwater volcanic cavern, on through the monitor room, and into the thermonuclear plant. Finally, the players come face-to-face with the evil Madame Q in the control room of her hidden headquarters. ThunderJaws Universal Kit
Players must battle the heinous creations of Madame Q throughout her empire. In addition to a plethora of lesser biomechanical creatures, players
- must fight with the Cyber Sharks, Manta Guys, Bionic Guards, Bionic Wolves, Lava Lords, Flame Dancers, Bat Babes, Spider ‘Bots, Rail Bots, Tread ’Bots, Punkers, and Madame Q’s own personal guards. The ultimate battle takes place where Madame Q transforms herself into her true identity: a grotesque mutant creature é of awesome ~~ power!
{I
CHAPTER 2
Self-Test
Use the ThunderJaws self-test
to check the condition of
the game circuitry and con-
trols. You will see the self-
test information on the
video display and hear the sound test infor-
mation through the speakers. You do not
need any additional equipment to perform
the self-test. Perform the self-test when you first set up the game, each time you
collect the money, or when you
_ Suspect game failure. This
. chapter shows the screens
in the self-test and explains each
of the tests. The screens and explanations
are arranged in the order they appear in the
self-test. Table 2-1 lists all the self-test
screens and their purposes.
Self-Test
Table 2-1 Summary of the Self-Test Screens
Select Test Menu
Switch ‘Test
Video RAM (looping). olor RAM (looping) ‘Common RAM—Video ONLY *» Common RAM—Secondary ONLY looping). Common RAM—BOTH processors (looping) AIL RAM (re-start) - Exit RAM tests ‘Compléte ROM Test Dual Playfield Test Motion ‘Object Test - Alphanumeric Test
Green Color Purity Blue Color Purity ‘White: Color Purity Grey: Color Purity = “Convergence Test. White Convergence ‘Violet Convergence
Green n Convergence
Entering and Exiting
the Self-Test
To enter the self-test, turn on the self-test switch on the game PCB. Exit the self-test by switching off the self-test switch at any time.
Choose which test or screen you want to see from this menu, shown in Figure 2-1. Move up and down the menu using the left joystick. Choose the screen by pressing the left fire button.
Statistics
Use the information shown on the statistics screen (see Figure 2-2) to keep track of your game use and maximize your profits. Record the information on the ThunderJaws statistics page in the back of this manual. The statistics are collected from the last time the statistics were cleared. You can clear the statistics by pressing the left Jump button. ThunderJaws Universal Kit
Figure 2-1 Select Test Menu Screen Left Coins shows the number of coins counted in the left coin mechanism. Right Coins shows the number of coins counted in the right coin mechanism. New Games shows the number of unique games played. A unique game is counted from the moment the first player started to the time the last player quit, regardless of how many times the game was continued. Cont Games shows the number of games that players continued. Total Games shows the sum of new and continued games. 0 Plyr Min is the number of minutes the game was idle. 1 Plyr Min is the number of minutes the game was played by one player.
q ogran
Figure 2-2 Statistics Screen
ThunderJaws Universal Kit
m= 2 Plyr Min is the number of minutes the game was played by two players. mL Plyr Min is the number of minutes the game was played by the left player. mR Plyr Min is the number of minutes the game was played by the right piayer. = Error Count shows the number of errors counted in the erasable memory. if you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 12C. m Total Coins is the number of coins put into both coin mechanisms. m Average Time Per Coin shows the result of dividing the total time (1 and 2 player minutes) by the total number of coins (left and right coins),
Game Options
Check and select the game options on this screen, shown in Figure 2-3. To move through the options, push the left joystick up or down. Change the option highlighted in red. The factory default settings are shown in lime green. To change a setting, move the left joystick right or left. To save the new settings, press the left fire button. This returns you to the menu screen. If you want to keep the original setting, although you have changed it, press the right fire button. This brings back the original setting. Use the left fire button to return to the menu screen. Self-Test
Figure 2-3 Game Options Screen
The game options, with defaults, are shown and explained in Table 2-2.
Coin Options
Check and select the coin options on this screen, shown in Figure 2-4. To move through the options, push the left joystick up or down. Change the option highlighted in red. The factory default settings are shown in lime green. To Table 2-2 Game Option Settings
genni Easy! 38 Moderate + Hard" «Hardest 2°34, 4° 5 10,000 points’ “25,000 points 50,000 points No extra lives +
ag'no io use your own chosen ‘Settin; "2 credits to start, 1 credit to continu No special cost'to start
Lets you set all the game options to the factory options or lets you use your own settings. Make sure you t this to
2-3
Self-Test ‘ThunderJaws Universal Kit
Figure 2-4 Coin Options Screen
change a setting, move the left joystick right or left. To save the new settings, press the left fire button. This returns you to the menu screen. If you want to keep the original setting, although you have changed it, press the right fire button. This brings back the original setting. Use the left fire button to return to the menu screen. The coin option settings, with defaults, are shown and explained in Table 2-3.
Sound Board Test
The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-5. Use the left joystick to select the sound and press the left jump button to listen to it. (You could have numer- Table 2-3 Coin Option Settings Figure 2-5 Sound Test Screen ous sounds playing simultaneously, depending on which ones you select.) You can also see the state of the two coin mechanism switches in this test: “0” indicates off, and “1” indicates on or closed. Pressing the right jump button stops all sounds, and pressing the left fire button returns you to the menu screen.
Switch Test
The switch test screen is shown in Figure 2-6. Test the buttons and joysticks. As you use each control, highlighting appears around its name on the screen. If the highlighting does not appear, check the connections, switches, and coin mechanism.
2 coins give 1 extra coin
- 4 coins give 1 extra coin. “4 coins give 2 extra coins’ 5 coins give 1 extra eéin 3.coins give 1 extra coin. “Free Play (for demonstration mode) + Manufacturer
2-4
‘ThunderJaws Universal Kit Self-Test
Table 2-4 When to Run the RAM Tests
| OHS | a | o | : | us | Location of | | |
Problem oe RAMs Tested |
| Ps | Playfield is erratic or | oe | | | |||
| eft: | Joystic! | ght | Joystick R | looks wrong. | ; | 6/7H, BH |
| eft | Joystick B | aystick D | Motion Objects are erratic Video RAM | / | ||
| © | ° | & | # | or not working propérly. | eo | i |
Colors look wrong.
Figure 2-6 Switch Test Screen
Press the left fire and jump buttons simultaneously to return to the menu screen.
Complete RAM Test
Use this selection screen, shown in Figure 2-7, to choose which RAM test you want to perform. Use the different tests according to Table 2-4. If you get an error in any of the RAM tests, see Table 2-5 for more information, If you have serious RAM problems, you may see only a colored screen. If this happens, see Table 3-5. To choose a test, move the box to the test name and press the left fire button. For all of the looping RAM tests, holding down the Fire button will cause the test to end when the current loop is completed. For some of these tests, this could take as long as several minutes. When the test ends, the screen will display the number of errors detected. Pressing the Fire button again will return you to the RAM test selection screen. toiay Error, Address
© 3F0000 3E0000
Return to the menu screen by moving the box to the words Exit RAM Tests, then press the left fire button to return to the menu screen. Selecting the Common RAM—Secondary Only or the Common RAM—Both test will also perform a communications test with the secondary processor before actually testing the RAM. If the message ERROR: NO COMMUNICATION WITH P2 is displayed, there is a problem with either the common RAM on the secondary processor circuitry itself. If you have already successfully run the Common RAM—Video ONLY test, then the problem lies with the secondary processor. If the Video ONLY test also fails, the problem is probably with the common RAM itself.
Complete ROM Test
The ROM test screen is shown in Figure 2-8. The ROM checksums appear. If the game has no ROM errors,
ci
Figure 2-7 Complete RAM Test Screen Figure 2-8 Complete ROM Test Screen
2-5
Self-Test
you are asked to return to the menu screen by pressing the left fire button. The location and checksum of each ROM are displayed on the screen. The data in parentheses indicates which processor the ROM is connected to (v = video, s = secondary, and c = common), its address range in 10000 hex (0, 2, 4, 6, and 8 indicate 00000 through 80000), and whether this is the high or low (H. or L) data byte. If the game does have ROM errors, the ROM test screen will remain until the ROM error information is complete, as shown in Figure 2-8. The ROM error test takes a few seconds. The locations of the bad ROMs are indicated on the screen. Press the left fire button to return to the menu screen, As part of the ROM test, the game also performs a communications test with the secondary processor. If the message ERROR: NO COMMUNICATIONS WITH P2 is displayed, the checksums for the secondary processor ROMs will not be reported. You should run the RAM tests Common RAM—Video ONLY, —Secondary ONLY, and BOTH to determine the cause of the failure. If you think you have a ROM error, but the screens show no messages, see Table 3-3 for information about the locations of various ROM functions.
Dual Playfield Test
The dual playfield test screen, shown in Figure 2-9, tests the transparency, movement, and color of various objects on both playfields. Pressing either of the two right two buttons allows you to switch to a new rear and front playfield picture. Pressing the left jump button brings the rear playfield to the front, or sends the front playfield to the rear. Use the left joystick to move the front playfield, and
Figure 2-9 Dual Playfield Test Screen ThunderJaws Universal Kit
the right joystick to move the rear playfield. Press the left fire button to return to the menu screen.
Motion Object Test
The motion object test screen, shown in Figure 2-10, tests the movement and color of various game objects.
Choose an object with the right joystick. Use the left joystick to move the object. Press the left fire button to go to the menu screen.
Alphanumerics Test
The alphanumerics test, shown in Figure 2-11, checks the condition of the alphanumerics in the game. In the ROM at 4M are eight separate banks of alphanumeric stamps. Pressing the left jump button cycles through all eight of these banks. If you see an error on the screen, check the EPROM at 4M. Press the left fire button to go to the menu screen.
Figure 2-11 Alphanumerics Test Screen.
‘ThunderJaws Universal Kit
Color Test
This test indicates the dynamic range of the video display color circuit. The screen is shown in Figure 2-12. The screen should show four bands (white, red, green, and blue from top to bottom), ranging from dark to
Figure 2-12 Color Test Screen bright, left to right. In addition, you can use the left joystick to move a thin horizontal band that “stains” or inverts the video level of whatever area it is positioned over. If the screen does not match this description, adjust the video display as described in the video display manual. Pressing the right jump button toggles the screen between 32 and 64 color levels. Pressing the left jump button alternately removes and shows the border, horizontal band, and text. Return to the menu screen by pressing the left fire button.
Color Purity Test
The color purity test has five screens. Each screen is a rectangle of color. The first screen, shown in Figure 2-13, is red. The other screens, which you can see by pressing the left jump button, are green, blue, white, and gray. These screens show the adjustment of the color purity of the video display. Each screen should display a rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. If the screens are not correct, adjust the video display as described in the video display manual. Return to the menu screen by pressing the left fire button, Self-Test
Figure 2-13 Color Purity Test Screen
Convergence Test
The convergence test has three screens: first white, then violet, and finally green. The white screen is shown in Figure 2-14. To see the violet and green
ae a ba ECE
EEBEEEEE PEE EE EEE EEE EEE PEEP
teh} oes PEEP EEE EEE EC EEe terre ees eoaaaceeazaeeaaeaeeereat behalabead “Thy NAA SHSSHo a0 EAC e0 BROSD BOUDoSE
screens, press the left jump button. If necessary, move the grid pattern by moving the left joystick. Press the left fire button to go to the menu screen. Check the following on the screens: m The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel. m The convergence of the lines on the violet and white screens should be within 2.0 mm. If these screens do not meet these criteria, adjust the video display as described in the video display manual.
2-7
Self-Test
N
2-8 ‘ThunderJaws Universal Kit
S
CHAPTER 3
~ Troubleshooting
and Maintenance
This chapter contains troubleshooting tables and repair procedures for your ThunderJaws game. The chap- ‘M -
ter has two parts. The first part contains three
troubleshooting tables. The first table has gen-
eral troubleshooting information, the second table contains the voltage levels and test points on the game printed-circuit board (PCB), and the last table de-
scribes ROM-caused problems with specific ROMs to check and replace. The last part of
the chapter has information about connecting
the video display if it requires separate posi-
tive sync, repair information for the joystick assembly, and locations of the RAMs and
ROMs on the game PCB.
Troubleshooting and Maintenance ‘ThunderJaws Universal Kit
Table 3-1 Troubleshooting Table
game turned on?. ‘Are the connections
Convergence, ay
3-2
‘ThunderJaws Universal Kit ‘Troubleshooting and Maintenance
Table 3-2 Voltage Inputs and Test Points on the PCBs
4540.25 VDC © V¢cl CR1 LED “= Lights when 5 V is applied to the PCB and the resét asp jumper is open. : JSA Audio II PCB: 2 CRS LED oe Lights when the +12 V supply is good. CR4 LED Lights ‘when the -5.V supply is good. CR3 LED Lights when the +5 V'supply is good. +VOP “412 V from the switching power supply. (pin 4 of IMB2) “© circuitry. -VoP -5V from the switching power supply Gf connie Negative supply for the :
| (pin 11 of LB) | analog circuitry. | 2 | j |
Table 3-3 What ROM Problems Look Like e 5 ‘ ROM Causing ae
| Problem | : | " | the Problem | _ Check the ROM at: |
Program Works but the motion ‘Objects or playfield are wrong.” Graphics i IP 17, 1R-17R, iS-i7S “Garbage 6n screen; program doesn't work.” . Program ROMs ea cave, 14E- 17E, 161, 17L, 1N,
| No sound. | : | Audio ROM. |
Erratic of wrong ADPCM sounds ADPCM ROMs.
Video Display Table 3-4 Atari Games Video
Se Connector Pin Assignments Sync Problems RISER ; : |
| Some video displays cannot use the composite nega- | Pins | : |
tive sync that is on the JAMMA connector. The Thun- 1 derJaws kit includes a standard Atari Games video 2 connector (located at 4A) that provides separate posi- 3 tive sync. Refer to Table 3-4 and make the appropriate 4 connections for your video display. 5 For other problems, see the video display manual that 6 :
| came with your game. | “ | d |
| ae | 8 | i |
aa) _
| Joystick Assembly | °0 | | |
| The joystick is shown in Figure 3-1. If you want to re- | 11 | ! |
pair the joystick, disassemble it by removing the E-ring at the bottom of the shaft and removing the screws. Table 3-5 Color Assignments for
ROMs and RAMs RAM Errors Encountered
| If you have think you have bad ROMs or RAMs, pre- | eo | = | i | |
| form the ROM or RAM test in the self-test. If you see | co Red | es | 2a | | |
| only a colored screen and cannot enter the self-test, | Black | lor or Common | i | |
| see Table 3-5. If you have a ROM problem, see Table | Anything else © | VAD ehip Se associated: video |
3-3. For the location of all the ROMs and RAMs on the : : game PCB, see Figure 4-3.
3-3
Troubleshooting and Maintenance ThunderJaws Universal Kit
Ball-Shaped Handle and Shaft
4 Lithium Grease
Plunger Spring
|__ Upper Housing ‘Assembly
Upper Housing
Cushion Ring
Pivot Balt
#8-16 X-Rec ~ Screw ~ < ©&D 1066" cia Rot Pin
8 Position Plate
Actuator Half-Ball
Figure 3-1 Maintaining the Joystick Assembly
3-4
CHAPTER 4
~ Parts Illustrations
This chapter provides
information you need
to order parts for
‘ your game. When
you order parts, give
the part number, part name, the number of
this manual, and the serial number of your
game. With this information, we can fill your of this manual. order rapidly and
correctly. We hope
this will create less
downtime and more
profit from your
games. Atari Games Customer Service phone
numbers are listed on the inside front cover
Parts Illustrations ThunderJaws Universal Kit
Figure 4-1 ThunderJaws Kit Parts List A047800-01 A
| Part No. | Description | Part No. | Description |
| 047205-01 | Attraction Shield | 178283-004 | Plastic Jump Indicator Plate |
| 047209-01 | Control Panel Cover | 72-6612S | #6 x 3/4-Inch-Long. Type PH, Cross-Recessed |
| 047805-01 | Kit Control Panel Decal | ‘Type-AB Screw | |
| 047806-01 | Side Panel Decal | 75-5112B | #10-24 x 3/4-Inch-Long Black Carriage Bolt |
A040933-03 _8-Way Joystick Assembly 047806-02 Poster
| 047807-01 | Auraction Pane] Film | A046501-01 | JAMMA Harness Assembly |
| 047809-01 | 19-Inch Bezel With Graphics | A047872-01 | ThunderJaws PCB Board Set Assembly. |
| 141026-001 | .50-Inch LD. Split Ferrite Bead | Consists of the following items: |
A047364-01 ThunderJaws Game PCB Assembly (see
| 160044-001 | Snap-Action Switch | Figure 4-3) | |
| 175014-1040 | #10 Flat Washer | A047184-04 | JSA Audio II PCB Assembly (see |
| 177010-240 | — #10-24 Hex. Polymer Locknut | Figure 4-4) | |
| 178032-002 | #10-24 Wire & Cable Tie | 177000-536 | 6-32 Nylon Nut |
178278-616 #6 Threaded PCB Support Standoff
| 178237-001 | Red Button Assembly | TM-349 | ThunderJaws Universal Kit Installation |
178237-005 _—_ Blue Button Assembly Instructions 178265-001 Nylon L-Style Standoff 178283-003 _ Plastic Start/Fire Indicator Plate
‘ThunderJaws Universal Kit
pe 107027-001 Lithium Grease
041287-01 Lower Housing
160044-001 Snap-Action Switch
Cushion Ring
039717-03 8-Position Plate (040304-01 Ball-Shaped Handle ‘and Shaft
NX
Upper Housing
176030-110 +#4-20 Screw |
03971401
039716-01 | Pivot Ball
73-20824 125" Dia Roll Pin
176018-003 #8-16 X-Rec “ Screw > 73-20509 ‘ .086" Dia Roll Pin
T 040693-01 ‘Actuator Halt-Ball
Figure 4-2 Microswitch Joystick Assembly A040933-03 B Parts Illustrations
(A047010-02 Upper Housing [— “Assembly
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Parts Illustratrations ThunderJaws Universal Kit
TDAZ030 ba 137579-001 SS “001 802_=_J0 §0>_= Tass Ls3943 Ls74 Ce) 0? ys 5) as 5 g L393 Ls13z +) 500 a
7 Ls138 a 137526-001 = Ls240 136056-2101 (Ij —=— 0s
Figure 4-4 JSA Audio II PCB Assembly A047184-04 A
Parts Illustrations Thunderjaws Universal Kit
N O T E S
CHAPTER 5
Schematic Diagrams
board (PCB) and the JSA
Audio II
diagrams for your ThunderJaws™ PCB. (The PCB assembly drawings are This chapter contains the schematic
universal kit. The schematics are of illustrated in Chapter 4, Parts Illustrathe ThunderJaws game printed-circuit tions.)
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ThunderJaws Universal Kit Schematic Diagrams
wk Cire copra 4h-——O
C38 copra ——o & s-TesT coPT4 tt ‘O = ok
+5V
1 iiJ BHH _ R73 +5V
ik
ysint. Louw at 5 Out _saun-21 0 ite pz eusy /SCBSY
| of | iA | DATA |
2 ai Tess AUD-27
| enmare | F remen | “" | 7 LO0Pr |
/SNORES ——7 Sderur &
| isco | on | ae | FIN saun-23 |
| /SCOMRD | Po . | a | = |
POWER-ON- aa [18 Ye
RS ; ;
| = | 470 | wr | SCLK_squp-25 |
= TooPF
S I / 0 UPDATED 2-20-90
Figure 5-1 ThunderJaws Game PCB Assembly Schematic Diagram 047363-01 A
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
‘ThunderJaws Universal Kit
R77 TP1S8 i ww Schematic Diagrams
/SCOMRD
/SWITCH
/SCOMHR /SNORES /LATCH
NOT STUFFED
135 —a] 13lp olt2_ Lake
So ALBKL aio 9 al —pLaKo ttl Sto ork A) Doge /ERESET Tr
/LATCH /8YSRES ——
Figure 5-1 ThunderJaws Game PCB Assembly Schematic Diagram 047363-01 A
5-5
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ThunderJaws Universal Kit Schematic Diagrams
a e SE e 6E| ry
2710240 2710240 2710240
"2 Sc 1o¢| e
| 2 | 2 | 2 | 2 |
| a | g | 2 | 2 |
| g | FA | g | z |
| 8 | 8 | g | 8 |
| z | 7 | = | z |
| 5 | 5 | 5 | ES |
+S
Zocure | cocve | eceuee | rocue| $a76
| qed: | dass | [eed | egy: |
7ROMO — “ROMS 7ROMZ — /ROM3
7VRAM 7WOOC UNLOCK 7EEPROM
Figure 5-1 ThunderJaws Game PCB Assembly Schematic Diagram 047363-01 A
5-7
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ThunderJaws Universal Kit Schematic Diagrams
ASH.
Zlase rey aro 2 2 2\, 8 a a AB lar Aes ASM Ae] a3 ae oa ie oof AO +50 We CS! 4 272d2z
/COMREM curve —t#!
| Eraar | veeou—t | ps0 |
a2i— 4} ZB —/comrem eptack —— SR crm er Eel jecom zas3—* 12 yeRome
| = | By | a 5 | le [venom |
cats that ERt7 2) ut AS eROMO Cart tsla3 a
| Bi? thar oy | res) | 8G J |
TERT ik
| aoa § | | | = | |
| a | = | | | Ra |
| or | 7 | | hh) Go | |
| os | f | 47 | Desay |
8s) TLO0PF oa 23] 02] Of oo) fo WE CS1 OE lerecze /COMRAM CHR
LOL 4 2 cos . Us32 $$ ct —-——— srr
Figure 5-1 ThunderJaws Game PCB Assembly Schematic Diagram 047563-01 A
Schematic Diagrams ThunderJaws Universal Kit
+sv sv
ri Sra bre ae 470 S470 S470 {5 SYNC _OUT reste saz HSYNC.OUT syrp-11
JAM-P
+3 “ yro-4
RTL 1x (SYNC ve USYNC OUT > yrg-10 3 I. lL. dor FOR: "Gor
«NOT STUFFED
oe *« = NOT STUFFED
Ro4 , 68 @ ed es Fa
x1 14.3184
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
‘ThunderJaws Universal Kit
+t
Cet ceo + res Schematic Diagrams
>Ji-15, 470/25 4707250
ROT
Coz vee I rcpt
‘VaAcNo
PR ND» 4-22
Ji-16
RY 10K
71RQ
2N3904
a] SELF-TEST 1s
Is /NMI SFULL, a an
8)
/ROI0 Ls240
¥ i> > > > DD a5
a T L Ins
bs so?
$06
sos
sot
$03
soz
SOL
soo
Figure 5-2 JSA Audio If PCB Assembly Schematic Diagram 046487-01 A
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
‘ThunderJaws Universal Kit
vee
| sat | " | ae | 7ROM |
3 2m se sALL $ ¢ 18 _/raw
| SAS | 3) F | |s6 | A138 |
| Baia | ~ | 2 | A128 |
| BAZ | 3 | ae sur | |
| rd | 4 | 38 | 7SRO |
sr//¥——4, oo EG
ONO
3F. PR Mix /REST cen oH —— /WRIO n SRLO 628 co TS JHRP Sry fe — HRV Siv32— /TROACK /ROIO /ROP
7WRIO
PRESET Schematic Diagrams
Fy
a —to at _ccrtre —4o ak cere Ayo Sa VFREG —tto 4 928 — ores tin alte 18.0 8
Figure 5-2 JSA Audio It PCB Assembly Schematic Diagram 046487-01 A
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ThunderJaws Universal Kit Schematic Diagrams
c24 YAMRUD 4
: ol
3.4
sheen
2. Tae - YAMAUC i Yi —— |
woEce “yu mo —!
a8 SA [1 4Oee8", /YRHRES alia leno eur SE yee loATa HP; Si sme ecltt Ssemi re 5 5 ecw cuz Ss POND, Ht
ACN Sono
Figure 5-2 JSA Audio Il PCB Assembly Schematic Diagram 046487-01 A
‘Schematic Diagrams ThunderJaws Universal Kit
N O T E S
tjaws Statistics Sheet
Statistics Screen
Plyr 0 Coins: Plyr 1 Coins: New Games: Continued Games: Total Games: 0 Plyr Mins: 1 Plyr Mins: 2 Plyr Mins: L Plyr Mins: R Plyr Mins: Error Count:
Total Coins: Average Time/Coin:
A.
ATARI
GAMES
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
fed ped eM e lel eN eM el ee ped pepe el ed eed elle eel pel fel pel ed pel el elelelel (ca
Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Seller’s plant; and
- Seller's examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
REE e ere eee eee ere eee el elelelelelel ele
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
, | Atari Games Corporation aah y A \X 675 Sycamore Drive ee a ATAI| P.O. Box 361110 A af AE" =