CATHODE RAY TOMES

Galaga 88 TM-319 1st Printing

Galaga '88 (Namco, 1987) · Technical Manual · 32 pages · 26 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

A ATARI GAMES

Galaga ’88*

Operators Manual

designed by Namicu Lid. Manufactured by Atari Games

Page 3

© 1988 by Atari Games Corporation. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A 38

Page 4

Galaga ’88

Table of Contents

Set-Up How to Use This Manual ......sssccssssssssssseesssesccsssseeccsseecsssnecsessveesssveceessetecsunecsanneeestte 1 Game Play . Maximizing Earning:

Self-Test Game Cptions Screen...

3 Game Conversion Remove the Control Panel... Disassemble the Control Panel. Remove the Decal... Apply the New Decal Install Hole Plugs (for pil Install the Control Panel Hardware. Install the New Bezel...... Change the Attraction Graphics Remove the Game PCB . Convert the Game PCB. Replace the Game PC.

4 Illustrated Parts Lists and Schematics

Galaga ’88 A.D.S. Game Statistics

Warranty

List of Illustrations

Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6

Table 1 Table 2 Table 3 Table 4 Converted Dragon Spirit Control Panel Constructing the Bezel. Jumper Orientation... Game Board Conversion... Galaga ‘88 ROM PCB Assembly Galaga ’88 Schematic Diagrams (8 sheets).

List of Tables

Game Specifications . Game Option Settings .. Game PC Board ROMs for Galaga ’88 RAM/ROM Error Messages

iii

Page 5

Chapter 1 Set-Up

How to Use This Manual

This manual is written for game operators and service personnel, and provides information for setting up, playing, testing, and maintaining your Galaga ’88 game. The manual is divided into the following chapters: ¢ Chapter 1 contains set-up and game play information. Chapter 2 contains self-test procedures. Chapter 3 contains conversion procedures. Chapter 4 contains the kit parts list and the game PCB parts list. Table 1 Game Specifications

Characteristic Specification

Power Consumption 124 V-A at 120 V Temperature +5° to +38° C (437° to +100°F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC, 60 Hz (U.S. games) Width 26.75 in. (70 cm) Depth 34.38 in. (87 cm) Height 70 in. (178 cm)

Game Play

This section of the manual describes the theme of the Galaga '88 game and the game play features. Introduction Galaga '88 is an updated version of the old favorite, Galaga, with more invaders and more player firepower. Galaga '88 gives players a chance to once again repel the invaders from the Galagan Kingdom. One or two players can ty their hand at fighting the invaders. This time the Galagans have four more allies, each with unique weapons and defenses that a player must overcome, By destroying special enemies or obstacles the player can get “items.” When a player has two items, he can warp to another sector to confront more Galagan ships with new strategies. In the Challenge Rounds, the player shoots down as many invaders as possible as the Galagans dance to a waltz, tango, march or jazz tune. Attract Mode In the attract mode, the game cycles through the title screen, the high score screen, and game play screens that give hints for playing Galaga ’88.

The player selects single or dual ship power. The objective is to destroy all the Galagan foes in each of the 29 sectors of the galaxy, with each sector more difficult than the last. Unique Features

  • More opponents. In addition to Boss, Goei and Zago, the orginal Galagan crew, Don, Nin, Ban, and Gan have been added. Each of the Galagans has a unique way of challenging the players.
  • Different types of ships. Players can choose single or dual ships (if the game option is set for dual and single). When the player retrieves a dual ship from the Boss's tractor beam, it turns into a triple ship with ten times the power of a single ship.
  • Challenge Rounds. In the Galaga ‘88 Challenge Rounds the Galagan invaders dance to a waltz, tango, Sousa march or jazz tune, while the player shoots down Galagans to earn bonus points. ° Warping to a new sector. By destroying particular enemies or obstacles and capturing two of their items, the player can warp to the next sector. ¢ Player challenge. Each sector has different mix of Galagans with different strategies to be overcome.
  • Win back captured ships. The player can win back ships captured in the Boss Galaga’s tractor beam. When the player destroys the Boss, the ships are released. If the player retrieves them, the ships become dual ships if they were single and triple if they were double. ¢ High Score Mode. Upon completing a game, a player can enter his initials if he is among the top eight scorers on the game.

Maximizing Earnings

The key to maximum earnings is striking a midpoint on game times. Game times must be short enough so that player turnover is high. Conversely, game times must be long enough to give a player a good value and insure repeat play (repeat play is crucial to longevity). Galaga '88 gives the operator the flexibility to tune game difficulty and enough statistics to make adjustments. . If collections seem low or are dropping off, first check all player controls and coin mechanisms for proper operation.

Page 6

Galaga "88

The options below help insure shorter game play time with maximum game revenue, as well as longevity at any location by generating continuous player interest.

  • Game continue option. Allows the player to continue at the last stage completed at the end of a game,
  • Five difficulty levels of game play. Select the level you need for your location.
  • Four extended play selections. Choose at what point level the player is permitted to continue the game.
  • Number of Fighters. Choose the number of fighters (or lives) the player receives at the beginning of each game.

Chapter 2 Self-Test

The Galaga ’88 game has two Ways to enter the Self- Test mode. If you turn on the self-test switch, and then turn on the game power, a RAM/ROM test is performed before you enter the Self-Test. If you turn on the self-test switch when the game is in the Attract Mode, you go directly to the Self-Test. If you turn off the self-test switch, the game returns to the Attract mode. For more information on entering the self-test, the selftest screens and the RAM/ROM tests, see your Pac-Mania* or Dragon Spirit* operator's manual. The Game Options and the A.D.S. screens have been changed for the Galaga '88 game and are described below. Game Options Screen The Game Options, shown in Table 2, indicates the Current settings of the coin and game options, and lets you change these settings. This table shows the options and the default (recommended) settings. A.D.S. Screens To see the A.D.S. (Auto Data Sampling) Screen, turn DIP switches 3 and 5 on while the game is in the Attract mode. The game automatically gathers the information for the A.D.S. screens. You do not need to set any switches, The game resets the data screen after each time you leave the A.D.S screens. The first screen shows the following statistics:

  • On Time—The time the game has been turned on in hours, minutes, and seconds.
  • Play Time—The time the game has been played in hours, minutes, and seconds.
  • Games—Total number of games played. Each game is the time between the first player starting and both players dying, regardless of time or number of quarters inserted.
  • 1P Games—Total games played as one-player games.
  • 2P Games—Total games played as two-player games.
  • High Score—Highest player score. The second screen shows the length of all games played. Table 2 Game Option Settings

Option Name Coins to start (Coin Mech 1) Available Settings 1¢, 2, 3, 4, 5, 6, 7, 8, 9 Coin(s) for 14, 2, 3, 4, 5, 6, 7, 8, 9 Credits

Coins to start 14, 2, 3, 4, 5, 6 7, 8, 9 Coin(s) for (Coin Mech 2) 14, 2, 3, 4, 5, 6, 7, 8, 9 Credits

Music in Sound On¢@ attract mode Sound Off

Cabinet type A B ce

Video display One Off orientation (flip)

Fighters (lives) 1, 2, 34, 4,5

Extended play granted at: A Cist @ 50,000 points; 2nd @ 140,000: 3rd @ 300,000; 4th @ 480,000) B (st @ 40,000; 2nd @ 120,000); 3rd @ 240,000; 4th @ 360,000) C Cst @ 40,000; 2nd @ 120,000); 3rd @ 240,000) D (ist @ 50,000; 2nd @ 140,000)

Game difficulty A Casiest) B (Easier) Gank) C (Medium) —_—D (Harder) E (Hardest)

Game continuation On@ Off

Fighter selector On (Single & Dual)# Off (Single Only) % Manufacturer's recommended settings

“These games are engineered and designed by Namco Lid. Manufactured by Atari Games. Trademark © Namco 1987.

Page 7

Chapter 3 Game Conversion

Remove the Control Panel

‘WARNING

To avoid electrical shock, turn off the game before performing any maintenance procedures.

. Unlock and open the upper coin door.

  • Reach up through the upper coin door opening and release the two spring draw latches located under the control panel on each side of the cabinet.
  • Grasp the control panel on the top edge (next to the display shield) and tilt the panel up slightly. Remove the panel from the front edge of the cabinet. Stand the control panel on its back edge by placing it in the wood slots located under the control panel on each side of the cabinet.
  • Disconnect the control harness connector from the Game PCB and disconnect the green ground wire.
  • Lift the control panel from the cabinet.

Disassemble the Control

Panel

  • Disconnect the wiring harness from all of the switches and the joystick.
  • Use a 15/16-inch open-end wrench to remove the stamped nuts holding the pushbutton leaf switches on the control panel.
  • With a 3/8-inch nut driver, remove the lock nuts that hold the joystick assembly on the control panel. 4, Remove the one- and two-player start switches. Hold the black bezel on the player side and turn the switch underneath counterclockwise.

Remove the Decal

1, After you remove the hardware from the control panel, remove the decal.

CAUTION Do the following procedure on a clean work surface so you do not get dirt on the surface of the control panel.
  • Start heating the decal in one corner with a heat gun or hair dryer. Pull up gently on that corner. Do not melt the decal! By applying heat and gently pulling up on the decal, you should be able to peel the decal off. CYou can remove the decal without heating it, but it is more difficult.)

Apply the New Decal

  • Clean the control panel to remove any adhesive that is still on it. Use a lint-free cloth (not a paper towel) wetted with isopropyl alcohol to remove the adhesive. Clean the control panel as many times as necessary to remove any remaining adhesive.
  • Position the Galaga ’88 decal so that the holes in the decal line up with the holes in the control panel.
NOTE

If you have a Dragon Spirit game, the two 1-3/16inch holes for the bomb pushbuttons will be covered by the Galaga ’88 decal. (See Figure 1.) Hole plugs are provided for these holes, but first install the decal.

  • Start attaching the decal by peeling off the backing on the top long edge of the decal. Keeping the holes lined up, and keeping the top edge straight, press the decaf down. Continue peeling off the backing and pressing the decal down on the control panel.

Install Hole Plugs (for Dragon Spirit Games)

1. . After the decal is completely attached, turn the control panel over. Use a sharp knife and cut out the decal over the two decal-covered pushbutton holes.

  • Push a hole plug into each hole from the front of the control panel. (See Figure 1.) Bend the tabs in each hole plug until they are flat against the control panel. This will keep the plugs from being pried out.

Install the Control Panel Hardware

  • Put the two pushbutton switches back into the holes. Tighten each stamped nut with a 15/16-inch open-end wrench.
Page 8

Galaga ’88

1”-Long Carriage Bolt

Control Panel Hamess

Cross-Bar Leaf Switch with Button Holder

Hole Plug (2 places) ~e.)

Bezel Assy —

Control Pane! Decat

Red Button Assy

Lock Nut

&-Position Joystick Assy

Figure 1 Converted Dragon Spirit Control Panel

  • Put the bezels for the 1- and 2-player switches back on the control panel and screw the pushbuttons back into them.
  • Put the joystick back on the control panel, and use a 3/8-inch wrench to tighten the four nuts that hold the joystick on the control panel. 4, Reconnect the harness wiring to the switches and the joystick (Dragon Spirit games only: Using tie wraps, tie back the wiring for the two switches you removed.) Reconnect the green ground wire.
  • Put the 24-inch strip of black adhesive-backed tape on the edge of the control panel where the control panel rests against the display shield.

Install the New Bezel

Two bezel pieces are included in your conversion kit. Each piece has covered tape on the back at one end. This tape attaches to the opposite side of the other bezel piece. See Figure 2.

  • Peel the cover off the tape on one bezel piece. Attach the tape the other bezel piece end without tape on it. Connect the other ends.
  • Remove the control panel as described above.
  • Remove the video display shield,
  • Remove the existing bezel from the foam tape that holds it in place.
  • Install the Galaga ’88 bezel. Use the pieces of white foam tape in the kit to attach it to the game.
  • Replace the video display shield.
  • Install the control panel.

Change the Attraction Graphics

  • Turn off the game power.
  • Remove the three screws in the retainer on the top of the cabinet. Remove the retainer.
  • Remove the attraction shield. The shield has foam tape on the front and back edges.
Page 9

Galaga ‘88.

1 Tape

Figure 2 Constructing the Bezel

4, Remove the old attraction graphics film and discard it. . Pac-Mania Games Only: Discard the Pac-Mania attraction shield and replace it with the shield included in the Galaga ’88 kit.

  • Slide the attraction shield into place. Ww
  • Put the Galaga '88 attraction graphics film over the shield.
  • Put on the retainer over the attraction graphics and tighten the the three screws holding the retainer.

Remove the Game PCB

  • Turn the cabinet power off.
  • Unlock and remove the front access panel from the cabinet.
  • Disconnect the harness connectors from the End PCB.
CAUTION ‘We recommend that only a qualified service technician convert the Game PCB. The PC board and the IC sockets can be easily damaged.
  • Use a Phillips screwdriver to remove the screws and washers holding the Game and End PCBs to the cabinet.
  • Holding the front edge of the Game PCB, slide it forward out of the slotted guide.

Convert the Game PCB

  • Put the game board set on a work bench with the larger ROM PCB (the Game PCB) facing up.
CAUTION

If you reverse the direction of any ROMs you can destroy them and perhaps destroy the PC board as well.

  • Remove the dust accumulated on the PC board by using compressed air or a soft brush.
  • Assemble the ROMs as listed in Table 3.
  • Figure 3 shows what ROMs must be removed, added, and replaced. Pac-Mania board changes are indicated by R for replace and A for add. Dragon Spirit board changes are indicated by R for replace, A for add and D for delete.
  • Remove the Pac-Mania and Dragon Spirit ROMs indicated in Figure 4. Using the number stamped on the Galaga '88 ROMs, Table 3, and Figure 3, replace and add the Galaga ’88 ROMs to the board. Be sure that all the ROMs are oriented the correct way.
  • Insert the ROM from the right end of the socket.
Page 10

Table 3 Game PC Board ROMs for Galaga ’88 Location Description Part No.

AdIC, EPROM, Galaga '88, VOI-O136062-1119

B4 IC, EPROM, Galaga '88, VOI-l — 136062-1120

E4IC, EPROM, Galaga '88, VOI-2136062-1121
F4IC, EPROM, Galaga 88, VOI-313662-1122

H4 IC, EPROM, Galaga °88, VOI-4 — 136062-1123

K4IC, EPROM, Galaga '88, VOLS136062-1124
A8IC, ROM, Galaga 88, CHR-O——136062-1114
BSIC, ROM, Galaga '88, CHR-113062-1115
E8IC, ROM, Galaga ‘88, CHR-2_136062-1116
F8IC, ROM, Galaga '88, CHR-3.1360621117
usIC, ROM, Galaga ‘88, CHR-8—136062-1118
EC)IC, ROM, Galaga ’88, OBJ-0136062-1108
BOIC, ROM, Galaga ’88, OBJ-1136062-1109

Location Description Part No.

E9IC, ROM, Galaga ’88, OBJ-2,136062-1110
F9IC, ROM, Galaga ’88, OBJ-3136062-1111
H9IC, ROM, Galaga ’88, OBJ-4136062-1112
K9IC, ROM, Galaga ’88, OBJ-5136062-1113

A10 _ IC, EPROM, Galaga ’88, SND-0 136062-1106

B10_IC, EPROM, Galaga ’88, SND-1_136062-1107
F10IC, Custom, 15399-090358
H10_IC, EPROM, Galaga ’88, PRG-O136062-1101
K10IC, EPROM, Galaga '88, PRG-136062-1102
P10IC, EPROM, Galaga ’88, PRG-5136062-1103
S10_IC, EPROM, Galaga ’88, PRG-6136062-1104

T10 IC, EPROM, Galaga ’88, PRG-7_136062-1105

When you plug in the ROM, be sure that none of the pins are bent or broken.

  • Check to be sure that the jumpers are oriented as shown in Figure 3.

Replace the Game PCB . Before reinstalling the board, check the orientation and location of each ROM to be sure it is inserted correctly.

  • Connect the End and Game PCBs together.
  • Holding the front edge of the Game PCB, slide it into the slotted guide in the cabinet. 4, Connect the harness connectors to the End PCB.
  • Use a Phillips screwdriver to tighten the screws and washers holding the Game and End PCBs to the cabinet.
  • Be sure that the top PCB is fully inserted into the bottom PCB edge connectors and that the ground strap is properly connected to the ground plane.

ROM JPI | JP2 | JP3

eee | BA! ALBEIR]Rl

28 | 5izk| EP_| AO HAO | orsi2 28_| 1M _| MASK | za O omm 32 jim |ep [own OA | nncicsnl| 32 | 275) og) oma] om an [ask] ii

Figure 3 Jumper Orientation Table 4 RAM/ROM Error Messages

Error Message Possible Bad Integrated Circuit ROM 0 Error ROM at location H10 on the ROM PCB ROM 1 Error ROM at location K10 on the ROM PCB ROM 2 Error ROM at location L10 on the ROM PCB ROM 3 Error ROM at location M10 on the ROM PCB ROM 4 Error ROM at location N10 on the ROM PCB ROM 5 Error ROM at location P10 on the ROM PCB ROM 6 Error ROM at location $10 on the ROM PCB ROM 7 Error ROM at location T10 on the ROM PCB RAM 1 Error* RAM at location B2, D2, or E2 on the CPU PCB RAM 2 Error RAM at location D6 or EG on the CPU PCB RAM 3 Error —_ RAM at location $5 on the CPU PCB RAM 4 Error RAM at location H1 on the CPU PCB RAM 5 Error RAM at location L5 on the CPU PCB RAM 6 Error* RAM at location B2, D2, or E2 on the CPU PCB RAM 7 Error RAM at location D6 or E6 on the CPU PCB V/O Error 64** RAM at location H1 on the CPU PCB, or the I/O Processor at location M4 on the ROM PCB

‘Either of these error messages may be accompanied by a four-digit number. Look at the first of the four lines and ignore the bottom three lines. Also ignore the fact that the entire screen may be upside down. This four-digit number may indicate one specific integrated circuit is bad, as follows: If the number is between 0002 and 0802, this indicates location B2. If ABCD is between 0804 and 1002, this indicates location D2. If ABCD is between 1004 and 1802, this indicates location E2. “If this error message is accompanied by a four-digit number, look at its left two digits. If those digits are 02, this indicates the RAM at location H1 is bad. If those digits are not 02, this indicates the /O Processor at location M¢ is bad.

Page 11

Galaga ’88

riozig6zige1

Figure 4 Game Board Conversion k

0 vag|>aaa888ai)fem
woFor Fs Fe Fs Bs ©*
iaa>>>>fe)? rs
jlHialg *

i al

a

a[ila*aa.
naafem4
sootewokaEmSmSmodmane2 mstom Z
s= Thy=fF 3a]>>Thft>|]>2:
qli7

So Ey

oHPasteHywfAati

faa] vey Ee

>om7==- =z»o4=

Explanation of Symbols

Letter Meaning

A Add ROM to Pac-Mania board. R Replace ROM on Pac-Mania board. A Add ROM to Dragon Spirit board. R Replace ROM on Dragon Spirit board. D Delete and remove ROM from Dragon Spirit board.

Page 12

Galaga ‘88

Chapter 4 Illustrated Parts Lists

Galaga ’88 Conversion Kit (A045166-01) Parts List

Part No. Description 038158-01 Product ID Label 044827-01 Auraction Shield 045167-01 Attraction Film with Graphics 045168-01 Control Panel Decal 045169-01 Half Bezel for Video Display 136062-1101 IC, EPROM, Galaga '88, PRG-0, H10 136062-1102 IC, EPROM, Galaga ‘88, PRG-1, K10 136062-1103 IC, EPROM, Galaga '88, PRG-5, P10 136062-1104 IC, EPROM, Galaga ‘88, PRG-6, S10 136062-1105, IC, EPROM, Galaga '88, PRG-7, T10 136062-1106 IC, EPROM, Galaga '88, SND-0, A10 136062-1107 IC, EPROM, Galaga '88, SND-1, B10 136062-1108 IC, ROM, Galaga '88, OBJ-0, A9 136062-1109 IC, ROM, Galaga '88, OBJ-1, B9 136062-1110 IC, ROM, Galaga '88, OBJ-2, ED 136062-1111 IC, ROM, Galaga ’88, OBJ-3, F9 136062-1112 IC, ROM, Galaga '88, OBJ-4, H9 136062-1113 IC, ROM, Galaga '88, OBJ-5, K9 136062-1114 IC, ROM, Galaga '88, CHR-O, A8 136062-1115 IC, ROM, Galaga '88, CHR-1, B8 136062-1116 IC, ROM, Galaga '88, CHR-2, E8 136062-1117 IC, ROM, Galaga '88, CHR-3, F8 136062-1118 IC, ROM, Galaga '88, CHR-8, US 136062-1119 IC, EPROM, Galaga '88, VOI-0, A4 136062-1120 IC, EPROM, Galaga ’88, VOI-1, B4 136062-1121 IC, EPROM, Galaga ’88, VOI-2, E4 136062-1122 IC, EPROM, Galaga '88, VOI-3, F4 136062-1123 IC, EPROM, Galaga '88, VOI-4, H4 136062-1124 IC, EPROM, Galaga ’88, VOI-5, K4 99-090358 IC, Custom, 153, F10 178225-001 1-13/16-inch Diameter Control Panel Hole Plug 78-6900402 1/4-Inch-Wide x 1/8-Inch-Thick Foam Tape TM-319 Galaga '88 Operator's Manual (includes game self-test label and card for ordering side-panel decals)

Page 13

(1021961198) 4, U oo

aa

ie)

ar

¥ a al W N d

Figure 5 Galaga ’88 ROM PCB Assembly 99-090359

Page 14

Galaga ‘88

Galaga ’88 ROM PCB Assembly Parts List

Part Number Description

Integrated Circuits 99-090108 IC, 74LS00 99-090117 IC, 7418138 99-090118 IC, 74L8139 99-090124 IC, 7418245 99-090125 IC, 7418257 99-090126 IC, 74LS273, 99-090127 IC, 7418373 99-090128 IC, 7418374 99-090132 IC, 74HC257 99-090155, IC, Custom 95 99-090157 IC, Custom 99 99-090158 IC, DAC, YM3012 99-090160 IC, Power Amplifier, LA4460 99-090244 IC, 7418244 99-090246 IC, 4066 99-090248 IC, Op-Amp, TLO84CN 99-090312 IC, 74FO2 99-090313 IC, 74F138 99-090314 IC, 74F244 99-090315, IC, 74F374 99-090316 IC, 74HC374 99-090317, IC, Custom 64 99-090318 IC, Custom 123 99-090319 IC, PAL, 16L8B-2 99-090320 IC, 78L06 99-090321 IC, LA4520 99-090322 IC, TA7630 99-090323 IC, LB1760 99-090324 IC, MB3771 99-090358 IC, Custom 153, F10 136062-1101 IC, EPROM, Galaga '88, PRG-0, H10 136062-1102 IC, EPROM, Galaga ’88, PRG-1, K10 136062-1103 IC, EPROM, Galaga ‘88, PRG-5, P10 136062-1104 IC, EPROM, Galaga '88, PRG-6, $10 136062-1105, IC, EPROM, Galaga ‘88, PRG-7, T10 136062-1106 IC, EPROM, Galaga 88, SND-0, A10 136062-1107 IC, EPROM, Galaga '88, SND-1, B10 136062-1108 IC, ROM, Galaga '88, OBJ-0, A9 136062-1109 IC, ROM, Galaga 88, OBJ-1, B9 136062-1110 IC, ROM, Galaga ’88, OBJ-2, E9 136062-1111 IC, ROM, Galaga °88, OBJ-3, F9 136062-1112 IC, ROM, Galaga '88, OBJ-4, H9 136062-1113, IC, ROM, Galaga '88, OBJ-5, K9 136062-1114 IC, ROM, Galaga ’88, CHR-0, A8

Page 15

Galaga ’88 ROM PCB Assembly Parts List, Continued

Part Number Description 136062-1115 IC, ROM, Galaga ‘88, CHR-1, B8 136062-1116 IC, ROM, Galaga '88, CHR-2, E8 136062-1117 IC, ROM, Galaga '88, CHR-3, F8 136062-1118 IC, ROM, Galaga '88, CHR-8, U8 136062-1119 IC, EPROM, Galaga ’88, VOI-0, A4 136062-1120 IC, EPROM, Galaga ’88, VOI-1, B4 136062-1121 IC, EPROM, Galaga ’88, VOI-2, E4 136062-1122 IC, EPROM, Galaga '88, VOI-3, F4 136062-1123 IC, EPROM, Galaga ’88, VOI-4, H4 136062-1124 IC, EPROM, Galaga ’88, VOI-5, K4 Resistors 99-090185 Resistor, SIP, 4.7KQ x 8, 1/8W 99-090187 Resistor, 4.7Q , 5%, 1/4W 99-090189 Resistor, 330Q , 5%, 1/4W 99-090191 Resistor, 470Q , 5%, 1/4W 99-090192 Resistor, 560Q, 5%, 1/4W 99-090194 Resistor, 4.7KQ. , 5%, 1/4W 99-090195 Resistor, 6KQ, 5%, 1/4W 99-090196 Resistor, 10KQ, 5%, 1/4W 99-090199 Resistor, 1 MQ. , 5%, 1/4W 99-090200 Resistor, 18 KQ , 5%, 1/4W 99-090253 Resistor, SIP, 5KQ, X 8 99-090255 Resistor, 100Q, 5%, 1/4W 99-090257 Resistor, 2.2 KQ, 5%, 1/4W 99-090261 Resistor, 47 KQ, 5%, 1/4W 99-090329 Resistor, 1.5 KQ, 1/4W, 5% 99-090330 Resistor, 12 KQ, 1/4W, 5% 99-090331 Resistor, 100 KQ, 1/4W, 5% 99-090332 Resistor, SIP, 1 KQ, 1/8W 99-090333 Resistor, SIP, 1.2 KQ, 1/8W 99-090334 Resistor, SIP, 1 KQ, 1/8W 99-090335 Resistor, SIP, 10 KQ, 1/8wW 99-090336 Resistor, SIP, 10 KQ, 1/8W Diodes 99-090250 Diode, 11588 99-090325 Diode, 1S1885 99-090326 Diode, 126.2 Capacitors 99-090174 Capacitor, Ceramic, 0,01pF, 25V 99-090175 Capacitor, Ceramic, 0.1)F, 25V 99-090269 Capacitor, Electrolytic, 10pF, 16V 99-090270 Capacitor, Electrolytic, 47pF, 16V 99-090337 Capacitor, Ceramic, 2200PF, 25V 99-090338 Capacitor, .0047pF, 50V 99-090339 Capacitor, .033pF, 50V 99-090340 Capacitor, .12yF, 50V

u

Page 16

Galaga "88

Galaga ’88 ROM PCB Assembly Parts List, Continued

Part Number Description

99-090341 Capacitor, .01pF, 50V 99-090342 Capacitor, 1pF, 25V 99-090343 Capacitor, Electrolytic, 47pF, 66.3V. 99-090344 Capacitor, Electrolytic, 470pF, 10V 99-090345 Capacitor, Electrolytic, 2.2yF, 16V 99-090346 Capacitor, Electrolytic, 4.7pF, 16V 99-090347 Capacitor, Electrolytic, 22pF, 16V 99-090348 Capacitor, Electrolytic, 220pF, 16V 99-090349 Capacitor, Electrolytic, 1000pF, 16V. 99-090350 Capacitor, Electrolytic, .47pF, 50V Inductor 99-090274 Inductor, 100pH, SP0406-101K Transistors 99-090310 Transistor, 2SA1015-Y 99-090327 Transistor, 2SC1815 99-090328 Transistor, 2SC2236-Y Miscellaneous 99-090351 Potentiometer, 10K 99-090352 Switch, DIP, 8 Circuit

Page 17

Galaga ’88

AMPS3PIN J104

Figure 6 Galaga ’88 Schematic Diagram

Page 18

Galaga ’88

E : __DIPSW aagaadil $257 A3 a cl rm 2

1D0-107

EDGE CONNECTOR & SW INPUT

Figure 6 Galaga ’88 Schematic Diagram, Continued

Page 19

Galaga ‘88

12V. fu FILTER

¢23 C10. @4700P_ 0.12 20 ce 0.12 _@z2700P AGNO

LCGi

LCG;

LCG3.

Figure 6 Galaga ’88 Schematic Diagram

Page 20

AUDLO AMP & 3D GRASS DRIVER

Figure 6 Galaga ’88 Schematic Diagram, Continued

Page 21

Galaga °88

1D0-7

SUBRES. CLK.

Figure 6 Galaga ’88 Schematic Diagram

Page 22

Galaga ’88

R26 C38 RB 41K 22/10 470 Se ae AUDIO Re JAESP 108 R26

RIS C32 47K 22/10

SOUND MIX 2 HEAD PHONE AMP

Figure 6 Galaga ’88 Schematic Diagram, Continued

Page 23

Of 2B

fm je | | 1 i OCK

3DS1G1. 30$1G2. = frst] 303 1G: 7RESET.

Figure 6 Galaga ’88 Schematic Diagram

Page 24

Galaga ’88

ls 13 Jus 13 Jus 13 fais 13]

Pe ; ioataa PObs Obs POs | io bs 13]

RESET, VOLCE ROM

Figure 6 Galaga ’88 Schematic Diagram, Continued | CONTROL,

Page 25

p12 ELT. 7HSYI SCROT Ri

LN LNI UNO

ee33°sPRI2
COS.33lcs tml?PRI
04Olearao 8PRIO
602.e2hc2 seaNM2
col£31 corsum [O.INM1
coee coy sere [tLSNMO

i $232}7212

Figure 6 Galaga ’88 Schematic Diagram

Page 26

Galaga ’88

22, 22 3 tus [3 [us [3 Tats 13. Ins 131

23 lacPS laaPSTPS Taxa9]In3
26luaPlaPSlus Pela PoaluaP83
ehhae[anPS Ia
23|uo BS lag3 bugPS Iarg B33
Zhe BIg TheThePgTagB
eeelestoSap 15 Ia

LC ce Is

Blu18 lefe lu ehle

Sha 19 lg] CEL

= = F374 56

SCROLL SCREEN CHARACTOR ROM

Figure 6 Galaga ’88 Schematic Diagram, Continued

Page 27

OCOL1. OCOLO. OHP.

OA0-18

OBJECT om6 #

OcGo-7

Figure 6 Galaga ’88 Schematic Diagram

Page 28

e & g

° Re ¢ S9seoy Bt segsggs

« Fefeas PEee 4: g a dad | IASAIAVIGYE aA8aagsa a fs = xlelalolehalsle RRR Rl [l2l=lI8)5) alel2/2{efetz|o 22ege al ) 24 Ing &

OBJECT CHARACTOR ROM

, Continued Figure 6 Galaga ’88 Schematic D:

Page 29

Galaga ’88

Ls138 Pit 7RO Sex bs A0-21 a al <a

A [70g 10 p70 fear tg gs hag 15 [24% 2°45 “pag MSS drab PAS IM27£096 M272096 IM272096 MS et 2v>-Baa HIO K10 Lio

ye04 1 a 1 Ie

LS244 E11 PD 17 3 2) =) 2A< 24) pg 15 1206 27405 06

7RO

00-7

Figure 6 Galaga ’88 Schematic Diagram

nN

Page 30

Galaga ’88

KEY.

2a:

ra

0}

RW_27

07 19

em :

ae nN se hy ee x S2e2ersddddddadddyStNsensggs ial ai ttisti 2 ist aan ae

Ra Butane Misia g 2 § a = Se g 2 ay = alalnistlalel Telekelstolol-lolelst-lal alelelelclelslet Sh,

PROGRAM ROM

Figure 6 Galaga ’88 Schematic Diagram, Continued

Page 31

SNDO-7, SNAO-13

DINIOOP 101

Figure 6 Galaga ’88 Schematic Diagram

Page 32

Figure 6 Galaga ’88 Schematic Diagram, Continued