CATHODE RAY TOMES

Centipede Cocktail DP-188-2nd-02A

Centipede (revision 4) (Atari, 1980) · Drawing Package · 1 pages · original scan

Page 1
Scan of page 1

From MPU Address Bus Sheet 1, Side B

Centipede Playfield RAM Testing the Playfield RAM

  • Perform the CAT Box preliminary set-up. 3
  • Set the CAT Box switches as follows: Prose TESTER RESET DBUS SOURCE TO ADDR BYTES to 1024 4 RIW MODE to (OFF) FW to WRITE Key in 0400 Set RIW MODE to PULSE, then to OFF. RI to READ Set FIW MODE to PULSE, then to OFF. TolFrom MPU. ‘Data Bus Sheet 1, Side 8 ererpaeer

From Syne Generator Sheet 1, Side B

Playfield Address Selector

The Playfield Address Selector controls the access to the playtield memory. Itallows either the game MPU or the sync generator to scan the playfield mem: Id Address Selector consists of multiplexers P5, and P7 and

When 3H on pin 1 of P5 and P7 is low and pin 15 on P7 is low, the Playfield

‘Address Selector receives 8H, 16H, 32H, and 64H on PS and 1V, 32V, 64V, and

128V on P7 from the sync generator. These signals enable the sync generator

circuits to access the playfield memory.

nen 7H goes high the game MPU addresses the playfield memory (via ‘AB0-AB9) forthe positioning of the graphics. During horizontal blanking (pin 15. ‘of P7 is high) the outputs of P7 (PFA4-PFA7) are held high enabling the motion bec culty to acess the pled memory for the mation objets to be isp

A. ATARI

Sheet 2, Side A

Centipede”

Playfield Memory Playfield Multiplexer Picture Data ROM Circuitry Motion Object Circuitry (Vertical) Motion Object Circuitry (Horizontal)

Section of 03724101 G

vere comncsion corey ‘Sheet 2, Side A e162 ed printing ‘CetipedeiCockta Playfield Multiplexer

The Playtield Multiplexer receives playfield data from

It the CAT Box reads an address that doesn't compare, the COM: PARE ERROR LED lights, the ADDRESS/SIGNATURE display shows the falling address location, and the ERROR DATA DIS- PLAY switch is enabled. Consists of select multiplexers KE, L6, M6, N6 and PS.

1 the COMPARE ERROR LED does not light, rekey 0400 and repeat the test with the DBUS SOURCE switch set to ADDR. This, fensures that the data bits at address 0400 will go high. If the COMPARE ERROR LED does not light after this step, the Play: fiold RAM is good. and to the picture data PROM circuitry (J6). When

picture data PROM circuitry. (PFOO-PFDS1) and the output (PFO-PF7) is a code that determines what is 1) dis played on the monitor, or 2) read or updated by the MPU. The Playfield Multiplexer

When 256H is low and 4H is high, AB4 and ABS from the MPU address bus is the selected output from PS. This output is applied to multiplexers KE, L6, M6, and NB as select inputs. When the MPU is accessing the playfield code multiplexer, the playfield datais elther being road or updated by the MPU. When 256H is high and 4H {s low, the inputs from the sync generator (128H and 8V) are the selected outputs. These signals then select which bits of data PFOO-PFDS1 are sent out via KB, LE, M6, and N6 for the playfield codes that eventually are displayed on the monitor.

The playfield codes (PFO-PF7) are latched by J6 and J6 to the MPU data bus (5)

‘syne Generator goes high, the inputs on JS (PFO-PF7) are latched out to the MPU via (DB0-DB7. When 4H on pin 11 of J6 goes high, the inputs (PFO-PF7) are latched to the the playfield memory From Syne | ere Generator ‘Sheet 1, Side 8

Is low and 1H from the

From Syne Generator ‘Sheet, Side 8 Motion Object Circuitry (Vertical) |

‘The Motion Object Circuitry (vertical) receives playtield data and vertical inputs from the syne generator circuitry to generate the vertical component of the motion object video. PFDB- 45 from the playfield memory and 1V-128V from the sync generator are compared at F6 and H6. | The output is gated by A7 when a motion object is on one of the sixteer vertical lines and is latched by E6 to AND gate B7. A low on B7 pin 8 indicates the presence of a motion object on. Cone of the vertical lines during non-active video time. This signal (MATCH) enables the multiplexers in the picture data circuitry

'When 256H on pin 1 of D7 goes high, 1V, 2V, 4V and PICO are selected. When 256H goes low, the latched output of E6 is selected. The output of D7 is EXCLUSIVE OR gated at E7 and is, ‘sent to the picture data selector circuitry as motion graphic address (MGAO-MGA3). The other | Input to EXCLUSIVE OR gate E7 is PIG7 from the playfield code multiolexer circuitry. PICT when high causes the output of €7 to be complimented. For example, if WGAO-MGA3 are low, PICT causes MGAO-MGAS to go high. This causes the motion object video to be inverted top to bottom, Motion Object Circuitry (Horizontal)

‘The motion object circulty (horizontal) receives playfield data and horizontal inputs from the syne generator circuitry, PFD16-PFD23 from the playfield memory determine the norizontal position of the motion object. PFD24.PFD29 from the playfield memory determine the indirect Color of the motion object. PFD6-PFD23 are latched by L7 and loaded into the horizontal posi tion counters AS and 85 by a low on pin 9. The horizontal position counters then address video RAMs AS and B6, These RAMS are loaded withthe video data for the particular motion object ‘rom shift registers H9 and J9 (which were loaded from the graphics ROM). The output for RAMs A6 and B6 is then sent to the color PROM circuitry as MRO and MRI. Picture Data ROM Circuitry

‘The picture data ROM circuitry receives picture Information, assigns a color code to the information ‘and sends it to the color PROM circuitry. The picture data ROM circuitry consists of ROM devices F7 and HN7, multiplexers F8, H8, J8, KB, shift registers H9 ‘and J9, and latch 8.

‘The picture ROMs receive (PICOPICS) from the playfield. code multiplexer, MGAOMGAS (motion graphics address) from the motion object circuitry, 26H and 256A from the sync generator. PICOPICS represent the code for the object to be displayed. MGAG-MGA3 set one of eight different combina tions of the ine by Bit Blocks of picture video or the 16 line by 8 Bit Blocks of motion object video.

256H when high selects the playtield picture col- ‘or codes to be addressed. 256H when low selects the motion object color codes to be addressed. The picture data ROM output D1-D8 on F7 and HIN? are multiplexed by F8, H8, JB and KB and shifted out ser. lally at H9 and J8. This serial output is latched by F9 ‘as AREAO and AREAL to the motion object horizontal circuitry and the video output circut.

From Syne Generator Shoot 1, Side B