CATHODE RAY TOMES

Millipede TM-217 1st Printing

Millipede (Atari, 1982) · Technical Manual · 64 pages · 52 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

See ee ee Aaya

lem, call TELEHELP® at the Atari Customer Service office in your geographical

area, as shown below.

rom New Jersey

@B (201) 469.5993 ne

else in this area

526-3849

Page 3

ATARI ws ANU DZCIE

Operation, Maintenance, and Service Manual

Page 4

Millipede™

© 1982 by Atari,Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The Millipede™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Lithographed in the U.S.A. 10L

Page 5

Millipede™

Notice Regarding Non-ATARI Parts

WARNING

Use of non-ATARI parts or modifications of your ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manuai) if you do any of the following: @ substitute non-ATARI parts in the game @ modify or alter any circuits in the game by using kits or parts not supplied by Atari.

TERFERENC

to licensed communications services is not permitted by the Federal Communications Commission (FCC). If you suspect interference from an ATARI® game at your location, check the following: @ all green ground wires in the game are properly connected as shown in the the game wiring diagram @ the power cord is properly plugged into a grounded 3-wire outlet @ the game PCB is properly installed within the Electromagnetic Interference (EMI) cage ®@ the EMI Shield PCB is properly installed and in series with the game PCB harness. Refer to Figure 3-13 to make sure that the game PCB and the Shield PCB are correctly installed. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover for service in your area.

Page 6

Millipede™

Table of Contents

Set-Up Procedures A. New Features 0.0... 0.0... e ne een eens 1-3 B. Inspecting theGame ....... 1-3 C. Space and Power Requirements 1-3

  • Installation Requirements . 1-4
  • Selecting the Voltage Plug. 1-4 D. Locating the Switches ... 1-4
  • On/Off Switch ..... 1-4
  • Utility Panel Switches . 1-4
  • Option Switches ...... 1-4 E. Setting the Option Switches . 1-5 F. Performing the Initial Self-Test : os 1-7 G. Game Play.............. : 18
  • Demonstration Mode 18
  • Attract Mode .... 1-8
  • Select Mode 19 4, Play Mode.... 1-9
  • High-Score Mode . 1-10
  • Hints forGame Play ..... 2.00.06. ccc eee eee 1:10

Self-Test Procedure A. Comments on Troubleshooting . : : 2-2 B. Performing the Self-Test... 2.0... 6c cece cece ene e eee 2-2

Maintenance, Repair, and Parts A. Cabinet-Mounted Assemblies 3-2 B. Control Panel ..............6..0-. sees 3-6 C. Fluorescent Tube, Speaker and Attraction Panel . 3-11 D. Video Display ... 3415 E. Utility Panel . 3-18 F. CoinDoor ........ 3-19 G. Printed-Circuit Boards . 3-22 H. Power Supply Assembly.............. 00 cc eee eee eee eens 3-33

Page 7

Millipede™

List of Illustrations

Figure 1-1 Game Overview, Upright Cabinet 1-2 Figure 1-2 Location of Game Switches... 1-4 Figure 1-3 Self-Test Display........... - 17 Figure 2-1 Self-Test Screen 1—Test Passes ............. 000.0 cece eee 2-2 Figure 2-2 _— Self-Test Screen 1—Test Fails... 0.6... 00.20... c cee eee 23 Figure 2-3. Self-Test Screen 2 24 Figure 2-4 — Self-Test Screen 3 24 Ilustrated Parts Lists Figure 3-1 Cabinet-Mounted Assemblies, Upright Cabinet .............. Figure 3-2 Cabinet-Mounted AssombliessIr Ireland-Built Cabinet . Figure 3-3 Control Panel Figure 3-4 — Control Panel Assembly Figure 3-5 — Midi-Trak-Ball™ Assembly . Figure 3-6 Fluorescent Tube and Attraction Panel, Upright Cabinet . Figure 3-7 Removing the Speaker, Upright Cabinet Figure 3-8 Fluorescent Tube, Speaker, and Attraction Panel, Ireland- Built Cabinet ..............05 eee Figure 3-9 Video Display, Upright Cabinet . . Figure 3-10 Video Display, lreland-Built Cabinet Figure 3-11 Utility Panel Assembly ........- . Figure 3-12 Vertically Mounted Coin Door ..... . 319 Figure 3-13 Removing the Printed-Circuit Boards ......... Figure 3-14 Millipede™ Game Printed-Circuit Board Assembly 3-24 Figure 3-15 | Regulator/Audio II Printed-Circuit Board Assembly .. 3-30 Figure 3-16 PowerSupply Assembly .......... 000.000. e eee eee eee 3-33

Table 1-1 Switch Settings for Price Options . . Table 1-2 Switch Settings for Play Options... Table 1-3 Switch Settings for Special Options . : Table 1-4 Self-Test Procedure ........... . 18 Table 1-5 Millipede™ Scoring .. 1-10 Table 2-1 Locating the Failed RA\ 23 Table 2-2 Locating the Failed ROM 23

Page 8

Millipede™

vi

NOTICE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio Communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.

Page 9

Set-Up Procedures

S<~ How to Use

this Manual

This manual, written for game operaiors and service technicians, describes the Millipede™ game. The manual contains information about the Upright and /reland-Built Millipede™ cabinets. Whenever information is unique to the Upright cabinet, this symbol appears:

Whenever information is unique to the /reland-Built

cabinet, this symbol appears: 4

Chapter 1 describes new features, game setup, settings of option switches, self-test procedures, and game play. Chapter 2 contains self-test procedures. Chapter 3 details maintenance, repair, and parts information. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.

Page 10

Set-Up Procedures

a FLUORESCENT TUBE, SPEAKER, & ATTRACTION PANEL ASSYS. See Figures 36, 3-7, or 3-8

VIDEO DISPLAY « See Figure 3-9 or 3-10

MIDI TRAK-BALL™ See Figure 3-5

CONTROL PANEL See Figures 33 & 3-4

COIN DOOR See Figure 3-12

UTILITY PANEL See Figure 3-11

POWER SUPPLY * See Figure 3-16

WARNING

SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

Figure 1-1 Game Overview

Upright Cabinet

1-2 Millipede™

GAME IDENTIFICATION LABEL *

N

ACCESS PANEL

GAME PCB « ‘See Figures 3-13 & 3-14

AN

ELECTROMAGNETIC INTERFERENCE (EMI) CAGE See Figure 3-13

REGULATOR/ AUDIO I! PCB See Figures 3-13 & 3-15

POWER ON/OFF SWITCH

  • Item with a serial number label
Page 11

Millipede™

A. New Features

The Millipede™ game has four new features. Even if you are familiar with ATARI® games, you should

note these important differences: 1. Midi Trak-Ball™. The popular Trak-Ball™ assembly has been enlarged and simplified. The housing for this new control is a molded plastic frame with two parts. Smooth action of the Midi Trak-Ball™ improves player accuracy. Molded Coin Box. This game has a lightweight, one-piece molded-plastic coin box with handles on both ends for easy carrying. Dual Speaker Assembly— Upright Cabinet. The two eight-ohm speakers are positioned so that the game audio envelops the player. Electromagnetic Interference (EM!) Cage— Upright Cabinet. Starting on December 1, 1982, the game PCB will be mounted inside this cage, thus reducing electromagnetic interference to television and radio receivers. New features and all other major parts of the game are illustrated in Figure 1-1. Throughout this manual, wherever one of these new features is mentioned,

you will see this symbol: om

B. Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition.

WARNING

To avoid electrical shock, do not plug in the game until the procedures in Sections B and C have been completed!

Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harness) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. Set-Up Procedures

Ensure that all plug-in integrated circuits on the PCB are firmly plugged into their sockets. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening.

Note the game serial number. It is printed on a label on the back of the cabinet. Verify that the same serial number is also on the Millipede™ game PCB, Regulator/Audio I! PCB, power supply, and video display. See Figure 1-1 for locations of the serialnumbered components. Please mention this serial number whenever you call your distributor for service. Inspect major subassemblies, such as the power supply, control panel, and video display. Make sure that they are mounted securely.
WARNING

To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!

C. Space and Power Requirements

WARNING

SHOCK HAZARD This game should only be connected toa grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

re 7 7 A e@PN)

Page 12

Set-Up Procedures

  • Installation Requirements

Power 150 W Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Upright Cabinet 62 x 85 cm (25 ¥2 x 33 % in.) 186 cm (73 in.) Ireland-Built Cabinet Space Required 60 x 68 cm (24 x 27 in.) Game Height 170 cm (67 in.) Space Required Game Height

  • Selecting the Voltage Plug

The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three separate voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). Before plugging in your game, check your line voltage. Next, check the wire color on the voltage selection plug that is plugged into your power supply. Make sure the voltage selection plug is correct for the voltage of your location (see Figure 3-16). Now, plug the game into a grounded 3-wire outlet. Millipede™

D. Locating the Switches

  • On/Off Switch

The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-2).

  • Utility Panel Switches The volume control, self-test switch, coin counter(s), and auxiliary coin switch are located on the utility panel (inside the upper coin door). Refer to Figure 1-2. Use the volume control to adjust game audio. Use the self-test switch to place the game in the Self-Test Mode. Use the coin switch to credit the game without activating a coin counter.
  • Option Switches

Option switches are located on the game PCB (see Figure 1-2). ¢ Price options are at PCB location B5.

  • Play options are at PCB location D5.
  • Special options are at PCB location P8.

UTILITY PANEL See Figure 3-11

COIN COUNTER

SELF-TEST SWITCH

VOLUME CONTROL (To increase, turn clockwise)

AUXILIARY COIN SWITCH POWER ON/OFF SWITCH OPTION SWITCHES

SWITCH AT BS (Game price)

SWITCH AT D5 (Game play)

SWITCH AT P8 (Special options)

OPTION SWITCHES

Figure 1-2 Location of Game Switches

1-4

Page 13

Millipede™

E. Setting the Option Switches

Tables 1-1, 1-2, and 1-3 contain settings of the game option switches. Options preset at the factory are shown by the <4 symbols. However, you may change the settings according to your individual needs. To verify option switch settings, set the self-test switch to the on position. Compare the information on the screen to the option switch settings listed in the Table 1, Table 2, and Table 3. Then set the selftest switch to the off position. Table 1-1 describes the switch settings for options telating to game price, coin mechanism multipliers, and bonus play. These switches are on the game PCB at location B5. Set-Up Procedures

The multipliers (switches 3-5) determine the value of the coin mechanisms to the game's logic. A coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. After this inspection, the mechanism either accepts or rejects the coin. The coin door has two mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a 2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1. You may offer bonus play for certain combinations of coins inserted. For example, with the game set at $.25 per play, players who deposit four successive $.25 coins before pressing the start switch can teceive a bonus play. The bonus feature encourages players to insert more money than the minimum $.25 required for one game.

Table 1-1 Switch Settings for Price Options

Settings of 8-Toggle Switch on Millipede™ PCB (at 85) 7 6 5 4 3 rs 1 Option

On On Off

On Off On Off On On

On Off Off

Off On Off

Off Off On

Off Off Off

Off On

Off Off

Off On On Off On On On

Off Off Off

On Off On Off Demonstration Mode For every 3 coins inserted, logic adds 1 more coin For every 5 coins inserted, logic adds 1 more coin For every 4 coins inserted, logic adds 2 more coins For every 4 coins inserted, logic adds 1 more coin For every 2 coins inserted, logic adds 1 more coin No Bonus Coins <4 Left coin mechanism x 1 < Left coin mechanism x 2 Right coin mechanism x 1 <4 Right coin mechanism x 4 Right coin mechanism x 5 Right coin mechanism x 6 2 coins for 1 credit 1 coin for 1 credit < 1 coin for 2 credits Free Play

“<Manufacturer's recommended settings

Table 1-2 details switch settings for Select Mode, game difficulty, number of lives, and bonus life options. The switches are on the game PCB at location D5. The Select Mode (switch 8 at location D5 is off) allows a player to start a game immediately after finishing a game at an advanced level of play. He receives bonus points for successfully completing play at that level. The maximum level that the player may select will be the bonus level below the last level achieved. For example, if the player scores 46,000 points, and the bonus life setting is at 15,000 (switch 5 is on and switch 6 is off), his last bonus was at 45,000. Therefore, he may select a starting score of 0, 15,000, or 30,000 points. In the easy spider setting (switch 7 is off), the spider moves slowly for the first 10,000 points. In the hard spider setting (switch 7 is on) the spider moves slowly for the first 5,000 points. After the point value is reached, the spider moves rapidly.

Page 14

Set-Up Procedures

In the easy beetle setting (switch 2 is off), the beetle moves slowly until 400,000 points, and four beetles appear in each wave after 500,000 points. In the hard beetle setting (switch 2 is on), the beetle moves slowly until 300,000 points, and four beetles appear in each wave after 350,000 points. Millipede™

In the easy millipede head setting (switch 1 is off), millipede heads enter from the sides of the screen at timed intervals. In the hard millipede head setting (switch 1 is on), millipede heads enter from the sides of the screen faster than in the easy setting.

Table 1-2 Switch Settings for Play Options

Settings of 8-Toggle Switch on Millipede™ PCB (at D5)

87654321

Option

Off

Ott On

Off Off

Off On

On Off On On

On Off On On Off

Off On Select Mode < No Select Mode Easy spider < Hard spider Bonus life every 12,000 points Bonus life every 15,000 points < Bonus life every 20,000 points No bonus life 2 lives per game 3 lives per game < 4 lives per game 5 lives per game Easy beetle < Hard beetle Easy millipede head < Hard millipede head

“4Manutacturer’s recommended settings

Table 1-3 details option settings for coin counters, minimum credits, Select Mode starting scores, and language. The switches are on the game PCB at location P8. You may choose the Select Mode starting score with switches 3 and 4. Make sure to enable the Select Mode by setting switch 8 at PCB location D5 to is off. The starting scores you may choose are 0, the amount of the bonus life setting, or multiples of the bonus. For example, with the bonus life setting at 15,000 points and the Select Mode starting score at 3 x bonus life level, the player may choose a starting score of 0, 15,000, 30,000 and 45,000 points.

Table 1-3 Switch Settings for Special Options

Settings of 8-Toggle Switch on Millipede™ PCB (at P8)

87654321Option

On 1 coin counter Off 2 coin counters On 1 credit minimum < Off 2 credit minimum Select Mode Starting Score

33OnOn0 points
3$OnOff0 and bonus life level
3s3SOffOn0, bonus fife level, and 2 x bonus life level <
==OffOff0, bonus life level, and 2 x bonus life level, and 3 x bonus

life level

OnOnEnglish <

On Off German

Off On French

ofOffSpanish

{Manufacturer's recommended settings

1-6

Page 15

Millipede™

F. Performing the Initial Self-Test

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. We suggest you perform the self-test procedure when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure. Set-Up Procedures

Wait at least 10 seconds after playing a game before switching to the Self-Test Mode. Otherwise, you may erase the top three scores in the high-score table or distort the statistics. All credits will be cancelled when you switch to self-test.

Refer to Figure 1-2 to locate the self-test switch and option switches. Set the self-test switch to the on position (see Figure 1-3) to see the Self-Test Display in the Self-Test Mode. To end the Self-Test Mode, set the self-test switch to the off position.

The complete self-test procedure is explained in Chapter 2, B. Self-Test Procedure. If a part of the test described in Table 1-4 fails, refer to Chapter 2.

LANGUAGE

BONUS COIN

MILLIPEDE HEAD SETTING

NO. OF LIVES BONUS LEVEL

SELECT MODE MAXIMUM STARTING VALUE

LOOT. ooorit OOO1OL OO0O1L

PLAYS ; 1:48 GAME TIME

SWITCH AT D5 (Game Play)

CONTROL PANEL SWITCHES

SWITCH AT P8 (Special Options) SWITCH AT BS (Game Price) GAME COST CHARACTER SET

BEETLE SETTING

SPIDER SETTNG

TRAK-BALL™ MOVEMENT

COIN SWITCHES.

TOTAL NO. OF GAMES

AVERAGE GAME TIME

Figure 1-3 Self-Test Display

Page 16

Set-Up Procedures Millipede™

Table 1-4 Self-Test Procedure Instruction Test Passes

  • Set the self-test switch to on (see Figure 1-2). All credits will be cancelled.
  • Press each control panel and auxiliary coin switches. Insert coins into both coin slots (coins will not be counted on the coin counter).
  • Roll the Midi Trak-Ball™

4, Press the 1-player start switch at least 64 times.

  • Press the 1-player start switch eight times.
  • Observe 16 blocks of color in the character set on right side of the screen.
  • Press and hold the 2-player start switch and press the FIRE switch. 8 Roll the Midi Trak-Ball™ and press 2-player start switch 16 times.
  • To erase the EAROM (erases the high-score table and game statistics), simultaneously press both start switches and FIRE.
  • To end the test, set the self-test switch to off. The self-test display appears. RAMs and ROMs are tested. The start LEDs remain on during the test. If the screen is different from the self-test display, or if there are sounds, refer to Chapter 2, Self-Test Procedure. When you press a switch, the appropriate 1 changes to 0 on the screen and you will hear a high tone. If the test fails refer to Chapter 2.

‘A motion object picture moves around on the screen in directions corresponding to the Midi Trak-Ball!™ If the test fails, refer to Chapter 2. Each time you press the tplayer start switch, the motion object changes shape. If test fails refer to Chapter 2. You will hear a high tone each time you press the 1-player start switch. If the test fails refer to Chapter 2. Each of the 16 block should contain a different color. if test fails refer to Chapter 2. Playfield objects change color with each press of the FIRE switch. If test fails refer to Chapter 2. Each time you roll the Midi Trak Ball™ and press 2-player start switch a motion object is moved from the diagonal group of objects in the center of the screen and placed in a new location on the screen. Test for 16 motion objects in this manner. If test fails refer to Chapter 2. The message EA FF appears in the upper left corner of the screen. The message remains on the self-test screen until the next game is completed.

G. Game Play

Millipede™ is a one- or two-player game with a color raster-scan video display. The game action takes place on a playfield filled with mushrooms, flowers, and deadly DDT bombs. The player tries to destroy a variety of insects that drop from the top of the screen or enter from the sides of the screen. The object of the game is to shoot and destroy as many objects as possible for a high point score. Player controls consist of a Midi Trak-Ball™ and a FIRE pushbutton. The Midi Trak-Ball™ controls a bow-shaped shooter. The shooter moves left, right, up, or down but stays in the bottom fifth of the screen. When the player presses FIRE, the shooter emits an arrow that travels upward. The player may fire one or many arrows (by pressing the FIRE button constantly). But only one arrow will appear on the screen at a time. A player may start a game at an advanced level of play and receive bonus points for starting play at that level. Refer to Section 3 and see Table 1-2 and Table 1-3 for this option setting. Millipede™ has six possible modes of operation: Demonstration, Attract, Select, Play, High-Score, and Self-Test. Self-Test is a special mode for checking the game switches and computer functions. You may enter the Seif-Test Mode from any other mode. However, all credits will be cancelled.

  • Demonstration Mode

To enter the Demonstration Mode, set switches 1 and 2 off and 7 and 8 to on at PCB location BS. In this mode all insects are harmless except the spider. Thus, to see all the game action, the player must destroy the spider. To exit this mode, reset the switches to your specitications (see Table 1-1).

  • Attract Mode

The Attract Mode begins when you set the power on/off switch to on, or after a Play, High-Score Mode, or Self-Test. Two pictures alternate in the Attract Mode. The high-score table is displayed in the center of each screen. The eight highest scores and players’ initials appear in this table. One picture displays various messages, the high-score table, and segments of simulated game play showing game characters. The score(s) of the previous player(s) and the highest score for the game are at the top of the screen. In the middle of the screen are messages relating to the cost of the game, bonus life, and credits (if any). If you select the option of two credits for one piay (see 7abie 7-7) and a piayer inserts one credit, the message 2 CREDIT MINIMUM flashes on the

Page 17

Millipede™

screen until the player inserts enough credits for game play. A “credit” is defined as the cost for each player to play one game. The copyright message is at the bottom of the screen. In the background is the simulated game play of a moderately skilled player. The player's shooter moves in the bottom fifth of the screen, shooting and destroying mushrooms and various insect characters. Periodically the shooter is destroyed when an insect hits the shooter. The other picture in the Attract Mode has ten boxes, each containing a different insect target. In addition, a field of mushrooms appears in one box, and the shooter destroying DDT bombs appears in another box. When enough credit(s) is inserted for a 1- or 2-player game, the appropriate 1- or 2-player LED flashes. When the player presses the flashing LED start button, the Select Mode begins.

  • Select Mode This mode begins when an LED start button is pressed. The Select Mode allows a player to start a game at an advanced level of play and to receive bonus points for starting play at that level. (See Table 1-2 and Table 1-3 for option switch settings for this mode.) For example, if the bonus setting is at 20,000 points, the player may start with 0, 20,000, 40,000, or 60,000 points. If the bonus setting is at 45,000 points, the player may start with 0, 15,000, 30,000, or 45,000 points. After playing a game, a player has 30 seconds to start the next game at a higher level. The maximum level which the player may select will be the bonus level below the last level achieved. For example, if the player scores 56,000 points, and bonus setting is at 15,000, nis last bonus was at 45,000. Therefore, he may select a starting score of 0, 15,000 or 30,000. The bonus level will never be more than 300,000 points. In the Select Mode the player has 10 seconds to select the bonus level. T/ME on the screen decreases from 9. The previous game scores) and high-score are at the top of the screen. Instructions on the screen tell the player to select a starting score. Below the instructions are up to four starting scores, depending on the select mode starting values (see Table 1-3). The player rolls the Midi Trak- Ball™ to the right or left to increase or decrease the score and find his starting score. Then he presses FIRE to complete his selection. At the bottom of the screen is a message showing the next bonus level. ‘Set-Up Procedures
  • Play Mode The Play Mode begins when the Select Mode ends. The Play Mode ends when the player’s last shooter is destroyed. The player's score(s} and the number of remaining lives are displayed at the top of the screen. The next bonus level is displayed at the bottom of the screen. Game play begins with a playfield of randomly placed mushrooms and DDT bombs. A millipede enters at the top center of the screen and starts snaking its way across the screen. The millipede changes direction when it runs into a fixed object in the playfield (mushroom, DDT bomb, flower, or another insect), or when it reaches the side boundaries of the playfield. When a segment of the millipede is shot, it is destroyed and a mushroom appears where that segment was shot. When shot, the millipede breaks into two smaller millipedes, each with its own head. When a millipede reaches the bottom of the screen, it will stay in the bottom fifth of the screen. New millipede heads enter the playfield, thus increasing the difficulty of game play. If a millipede reaches the bottom of the screen without being shot, it releases its tail. This tail changes into a new head. A round of play ends when all millipede segments are destroyed. The screen then scrolls down one line. When the millipede with only four segments enters from the top of the screen, the screen will scroll down every two seconds. The only way a player can stop the scrolling screen is to shoot a DDT bomb or destroy the entire miilipede. The screen scrolls up when a mosquito is shot. It takes four shots to destroy a mushroom. After a period of time, the entire playfield of mushrooms changes. Some mushrooms die and new mushrooms grow where there were none before. A mushroom next to a DDT bomb becomes poisoned. When a millipede runs into a poisoned mushroom, two things happen. His head changes color, and he changes direction and falls vertically to the bottom of the screen. DDT bombs explode when hit by an arrow. Any object near the bomb is engulfed by the explosion. Insects are worth more than normal if they are destroyed by the explosion (see Tab/e 1-5). Spiders appear in any round. They move in a random pattern on the bottom third of the screen. As the player's score increases, the range of the spider decreases, until it is confined to the bottom fifth of the screen. Also, more spiders enter as the game progresses. A spider destroys any mushroom or

1-9

Page 18

Set-Up Procedures

flower it moves over. The player earns 300, 600, or 900 points for destroying the spider, depending on the distance the shooter and the spider are from each other. Depending on a special option switch setting, the spider moves slowly until a player reaches a specific score, and then it speeds up (see Table 1-2). |f the player's shooter and a spider collide, both are destroyed. When a millipede with fewer than eleven segments appears, an earwig enters the screen. AS the player earns more points, the earwig’s speed increases. If an earwig passes over a mushroom, it poisons the mushroom. Earwigs are worth 1,000 points when destroyed. When a millipede with fewer than ten segments appears, a dragonfly enters at the top of the screen. The dragonfly moves in a zig-zag pattern and its speed increases as the player's score increases. AS the dragonfly moves, it leaves a trail of mushrooms behind. Dragonflies are worth 500 points when destroyed. When a millipede with fewer than nine segments appears, a mosquito enters at the top of the screen and flies in a diagonal pattern. The mosquito’s speed increases as the player's score increases. Mosquitos are worth 400 points when destroyed. Beetles appear randomly after the first round. They enter from the sides of the screen near the bottom, travel down to the bottom of the screen, and walk at least half way across the bottom. Then the beetle travels up and exits at the side of the screen. If a beetle passes over a mushroom, the mushroom changes into a flower. Flowers cannot be destroyed by the beetle. Depending on an option switch setting (see Table 1-2), the number of beetles appearing on the screen and the speed of the beetles increase as the player's score increases. When a beetle is destroyed, the screen scrolls down one row. Beetles are worth 300 points. Bees may fall from the top of the screen during any round. As the bee falls, it leaves a trail of mushrooms behind. The first time the player shoots a bee, it speeds up. The second shot destroys a bee. Bees have a value of 200 points when destroyed. An inchworm may appear when a millipede with fewer that eleven segments appears. The inchworm travels from one side of the screen to the other side. It moves slowly until the player's score reaches 80,000 points. Then it speeds up. If the player destroys the inchworm, all insects will slow down for about three and one-half seconds. The inchworm is worth 100 points when destroyed.

1-10 Millipede™

After a millipede of one, three, five, seven, or eleven segments has been destroyed, an insect bombing raid occurs. A raid may have only bees, dragonflies, mosquitos, or a mixture of all three. When the insect is shot, a point value appears on the screen in its place. With each additional insect hit, 100 points will be added to the previous value, up to 1000 points.

Table 1-5 Millipede Scoring

Object Points Spider 300, 600, 900, 1200 Earwig 1000 DDT Bomb 800 Dragonfly 500 Mosquito 400 Beetle 300 Bee 200 Inchworm 100 Millipede Head 100 Milipede Body 10 Mushroom 1

  • High-Score Mode The High-Score Mode begins when a player has earned one of the eight highest scores. The player has two minutes to enter his initials. A player rotates the Midi-Trak-Bali™ left or right to locate his initial. He presses FIRE to select his initials and transfer the initials and score into the high-score table. To reset the high-score table, switch the game off and then on, or set the self-test switch on and off (the latter will not erase the three highest scores.) To erase the three highest scores, refer to Section F in this chapter.
  • Hints for Game Play
  • Destroy mushrooms near the bottom of the screen.
  • Destroy the DDT bomb when the Millipede is beside it.
  • When amillipede hits a poisoned mushroom, it changes direction and falls vertically. Anticipate the place the miltipede will fall, because shooting it as it falls destroys all its segments.
Page 19

Self-Test Procedure

The following self-test procedures should be performed by a qualified electronic technician. This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you find the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is or is not working properly.

Chapter

Page 20

Self-Test Procedure

A. Comments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio || printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you find no harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting the PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram.

B. Performing the Self-Test

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. To switch to the Self-Test Mode, set the self-test switch, iocated on the utility panei, to the on position. Millipede™

SELF-TEST SCREEN 1—Test Passes:

If the test passes, the screen displays the picture in Figure 2-1—Test Passes. See Chapter 1, Section F, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off. Simultaneously press the self-test switch and the auxiliary coin switch. To see self-test screen three, press the auxiliary coin switch.

ENGLISH FREE PLAY

ASY SPIDER SELECT 30000 000001 OOOOdL Beet 100111 Ye oooL1L QOOLOL OOOOLL

173 PLAYS 1:48 GAME TIME DIOOMNALIHEA-ZZOVOAVMCCER<N: INI SeHNOWD

Figure 2-1 Self-Test Screen 1— Test Passes

Page 21

Millipede™

SELF-TEST SCREEN 1—Test Fails:

RAM failure is indicated by a blank or “garbage’’-filled screen and a number of tones. Count the tones to determine the failed RAM. The tone number and matching RAM location are shown in Table 2-1. The number of tones continue to repeat. Replace the failed RAM and restart the test (set the self-test switch to off, and then to on).

Table 2-1 Locating the Failed RAM

Failed RAM Location on Game PCB Number of Tones

F2 E2 M2 N4 l2 M4 K2 L4 v2 K4 BOBND TRONWH

ROM failure is indicated by two groups of alphanumeric characters in the upper left corner of the screen (see Figure 2-2). The group at the far left indicates the location of the failed ROM/PROM. Ignore the group at the right of the ROM number. The failed ROM and its location are listed in Table 2-2.

Table 2-2 Location of Failed ROM

Failed

Screen ROM Location

Display on Game PCB

Rt MINI R2 u R3 J/K1 Ra H1 EA P2 PO D4 Pq Ba

Oe Si re Self-Test Procedure

ENGLISH

FREE PLAY

EASY STDEFEED EASY BEETLES

SY SPIDER SELECT 30000 OOOOOL OooddL 1LOO00L OOLLOL y LOOL11 QoOOL111 oo0o101 OOOO1LL

173 PLAYS 1:48 GAME TIME DUOOMNALHCAKMZZOVOAUACCEX<N: SERWAUMDNIGWO

Figure 2-2 Self-Test Screen 1— Test Fails

SWITCH failure is indicated by the appropriate 7 not changing to a0 on the screen when you press a switch. There may be a constant tone, or no tone at all. Check if the volume control is turned off. Or check the switch, loose harness or connector wires, or the custom audio I/O chip. Troubleshoot using the information in Chapter 3, Section B, and the game schematics. MIDI TRAK-BALL™ failure is indicated by no movement or jerky movement of the player's shooter when you roll the Midi Trak-Ball™. If the cursor fails to move, or if movement is reversed or jerky, suspect the Midi Trak-Ball™ or the harness (see Figure 3-5). SOUND failure is indicated by the absence of any sound when any of the control panel or coin switches are pressed. Press the 1-player start switch 8 times to test all 8 channels. No increase in volume or change in pitch, or no tone when you press and hold the 2-player start switch and press the 1-player start switch, indicates failure. Suspect the volume control on the utility panel, the custom I/O chips, or troubleshoot using the game schematics.

2-3

Page 22

Self-Test Procedure

COLOR failure is indicated by no color change in the background or playfield objects. Background color should change when you press the 1-player start switch. Playfield objects should change when you press the 2-player start switch. Troubleshoot using the game schematics and the video display manual. MOVING OBJECT failure is indicated when the object represented as the shooter does not change shape each time you press the 1-player start switch. Press the 1-player start switch 64 times to see all shapes. Suspect the EPROM may be bad, or troubleshoot using the game schematics. To see self-test screen two, set the self-test switch to off, then simultaneously press the auxiliary coin switch and the self-test switch.

SELF-TEST SCREEN 2:

This screen displays 64 rectangles, each with varying intensities of red and blue (see Figure 2-3). The column on the left edge of the screen should show eight shades of blue from black at the bottom to bright blue at the top. The bottom row should show eight shades of red from black at the left to bright red at the right. The remainder of the screen shows blends of red and blue. Adjust the color guns (see the video display manual) so the lower left corner is black and the other corners are bright blue and red.

Figure 2:3 Self-Test Screen 2

2-4 Millipede™

Press FIRE and the screen displays 64 intensities of green. The lower left corner should be dark green. Press FIRE again, and the green becomes more intense. Press FIRE a third time, and the green becomes even more intense. The upper right corner should now be white.

SELF-TEST SCREEN 3:

Press the auxiliary coin switch and the screen displays a test pattern with white dots on a black background (see Figure 2-4). Troubleshoot convergence using to the video display manual.

Figure 2-4 Self-Test Screen 3

Page 23

Maintenance, Repair, and Parts

This chapter details maintenance and repair information and provides information you need to order parts for your game. Common hardware (screws, nuts, washers, bolts, etc.) has been deleted from most of the parts lists. However, there is a parts list for the hardware needed to mount the printed circuit boards (PCBs) to the cabinet. The printed circuit board (PCB) parts lists are arranged in alphabetical order by component. Each component subsection is sorted by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lisis, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598-through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order tapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter

Page 24

Maintenance, Repair, and Parts

A. Cabinet-Mounted

Assemblies

Oy. A039301-01 (Cabinet assy)

Fluorescent Tube, Speaker, & Attraction Panel See Figures 3-6 & 3-7

Video Display See Figure 39

039317-01 {Display shied) cn Midi Trak-Bali™ See Figure 3-5

Control Panel Assy. See Figures 33 & 3-4

038870-01 (Coin box enclosure) Coin Door Assy. See Figure 3-12

Utility Panet See Figure 3-11

eS 038091-01 See Figure 3-16 (Coin box)

78-3201 (Glide) Power Supply Assy. Milllpede™

03733201 (Vert. grille)

> Ss dating, (T-Molding)

\ A038881.01

(Lock)

  • 039349.01

ra (Access pane!) os 038178.03 (Cleat)

aR, Cage See Figure 3-13 Game PCB Assy. See Figures 3-13 & 3-15

A039259-01 (Main han. assy.)

Regulator/ Audio II PCB Assy. See Figures 3-13 & 3-15

A039260-01 (Power harn. assy.)

A037453-03, A037455-03, or A037784-03 A037470-01 TTEOHEOOY —Goratrewten easy) FONE CTD 009992.01 (On/off switch cover)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Peproduction torsidden withou! the spectic ‘writen permission of Atami, Inc., Sunnyvale. CA. This érawing ‘only conaitionally issued, and neither receipt nor possession Inereot conlers or transfers any right in, or license fo use, the subject rratler of the drawing oF ary design or technical mformation shown tnereot, for any fight to reproduce this drawing or any part thereo!. Except for manufacture by vendors of lati, Inc . and for manulacture under the corporation's writen icense, 180 fight to repreduce ths drawing 15 granted or Ihe subject matler thereot unless by writlen agreement wih oF written permission trom the corporation

Figure 3-1 Cabinet-Mounted Assemblies Upright Cabinet A039300-01 A

3-2

Page 25

Millipede™ Maintenance, Repair, and Parts

Cabinet-Mounted Assemblies Upright Cabinet Parts List

Assemblies and components in the following parts list are shown in Figure 3-1.

Part No. Description A037453-03 Strain-Relief Power Cord (U.S. and Canada) A037455-03 Strain-Relief Power Cord (Australia and New Zealand) A037470-01 Power On/Off Switch/Mounting Plate Assembly A037701-01 EM\ Cage Assembly A037784-03 Strain-Relief Power Cord (United Kingdom, Ireland, Lebanon, Saudi Arabia, India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe) A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A039259-01 Main Harness Assembly A039260-01 Power Harness Assembly A039301-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039502-01 Electromagnetic Interference (EMI) Shield PCB Assembly The following four items are the technical information supplements to this game: SP-217 Millipede Schematic Package ST-217-01 Millipede Label with Self-Test Procedure and Option Switch Settings TM-217 Millipede Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) Acceptable substitute is TM-160, use with part no. 92-049 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x ¥-Inch Thick (not shown) 78-3201 Adjustable Glide 009992-01 On/Off Switch Cover 037332-01 Ventilation Grille 038091-01 Molded Coin Box 038178-03 Dual-Slotted PCB Cleat 038870-01 Metal Coin Box Enclosure 039317-01 Video Display Shield 039349-01 Rear Access Panel (does not include lock) 178013-001 Spring Draw Latch (not shown) 178034-024 %-Inch Black Plastic TMolding 178048-001 2-Inch Rigid Caster

3-3

Page 26

Maintenance, Repair, and Parts

A039448-01 (Cabinet assy.) Fluorescent Tube, Speaker, & Attraction Panel See Figure 3-8

038986-01 (Retainer)

Video Display See Figure 3-10

038992-01 (Display shield)

038805-01 > (Retainer—not shown) Midi Trak-Ball™ sreo13001 See Figure 3-5 \ (Latch) Control Panel Assy. See Figures 3-3 & 3-4 Millipede™

178034-024 (T-Moiding) 038988-01 (Vent. grille)

A038881-01 (Lock)

03897602 (Access panel)

038240-1800 (Cleat)

Game PCB Assy. ‘See Figures 3-13 & 3-14

aa A039257-01 (Main harn. assy.)

038870-01 ; Coin Door Assy. (Coin box io See Figure 3-12 enclosure) eeu Ae See Figures 3-13 & 3-15

A038854-01 (Power harn. assy.) Panel See Figure 3-11 !

A037454-03 (Power cord) Power Supply Assy. (ower cord) See Figure 3-16 A037470-01 (Onvoft switch assy) 038091-01 ! 009992-01 (Coin box) (On/off switch cover)

78-3201 (Glide) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction forbidgen without the specilc watitten permission of Atari, Inc, Sunnyvale, CA. This drawing 1S only conditionally issued, and ‘neither receipt nor possession thereot conters ot transfers any right in, oF license to use. the subject matter of the drawing or any design or technical informa: tion shown thereon, nor any right to reproduce this drawing or any part thereot Except for manutacture by vendors of Alar log . and tor manutacture under the corporation's wetten license, No Tight Io reproduce Ihis drawing 's granted or the subject mat ter thereol unless by writlen agreement with or written permis: sion trom the corporation

Figure 3-2 Cabinet-iMounied Assembiies lreland-Built Cabinet A039440-01 & -02 A

Page 27

Millipede™ Maintenance, Repair, and Parts

Cabinet-Mounted Assemblies lreland-Built Cabinet Parts List

Assemblies and components in the following parts list are shown in Figure 3-2.

Part No. Description A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A037470-01 Power On/Off Switch/Mounting Plate Assembly A038854-01 Power Harness Assembly A038881-01 Lock Assembly (for rear access panel) A039257-01 Main Harness Assembly A039448-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) The following four items are the technical information supplements to this game: SP-217 Millipede Schematic Package ST-217-01 Millipede Label with Self-Test Procedure and Option Switch Settings TM-217 Millipede Operation, Maintenance, and Service Manua! TM-220 Service Manual for 19-inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) Acceptable substitute is TM-160, use with part no. 92-049 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, 14-Inch Wide x Inch Thick (not shown) 009992-01 On/Off Switch Cover 038091-01 Pa N\) Molded Coin Box 038240-1800 Printed Circuit Board Cleat 038770-01 Metal Coin Box Enclosure Acceptable substitute is part no. 038781-01 038790-01 Front Video Display Support Bracket (not shown) 038805-01 Display Shield Retainer (not shown) 038976-02 Rear Access Panel (does not include lock) 038986-01 Attraction Panel Retainer 038988-01 Ventilation Grille 038992-01 Display Shield 039009-01 Rear Video Display Support Bracket (not shown) 178013-002 Spring Draw Latch 178034-024 3A-Inch Black Plastic T-Molding

Page 28

Maintenance, Repair, and Parts

B. Control Panel

A— warning ——A Switch the game to off before you remove or repair any switch on the control panel.

Opening the Control Panel:

  • Unlock and open the coin door (see Figure 3-3). Reach up through the opening to the top of the control panel and release the spring-draw latches. For the /reland- Built cabinet, remove the two button-head screws that secure the top of the panel to the cabinet. 2, Close the coin door.
  • Lift the control panel at the top edge and tilt it toward you. The control panel on the Upright cabinet has foam tape on it. Make sure the tape is in good condition.

Repairing the Leaf Switch*:

  • Adjust the leaf switches for a narrow gap. When a switch button is pressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Do not burnish the contacts. To clean them, use electrical contact cleaner.
  • To remove a leaf switch, disconnect the wires and remove the screw with a Phillips-head screwdriver. Millipede™
  • To remove the switch button, turn the nut with a wrench in a counterclockwise direction from inside the control panel. The ring on the outside of the control panel should not spin.
  • Replace the switch, reconnect the harness wires as shown in the Schematic Package, Game Wiring Diagram. Make sure the colored wires are routed to their matching colored tabs on the switch.

Repairing the LED Start Switches*:

These switches have a very low failure rate. If you suspect switch failure, test it using the following directions. Testing the LED Switch*:

  • Disconnect the wires from the switch.
  • Attach the leads of an ohmmeter to the normally open and common contacts.
  • Check the contacts (push and release the switch button) for closed and open continuity.
  • If the contacts do not operate sharply or always remain closed or open, replace the switch.

Replacing the LED Switch*:

  • Disconnect the wires from the switch.
  • Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. Install a new switch using the reverse procedure.
  • Reconnect the wires as shown in Figure 3-3.

Circled numbers match numbered instructions. Disassemble in the order indicated.

  • not shown in illustration

Figure 3-3 Control Panel

3-6

Page 29

Millipede™ Maintenance, Repair, and Parts

A WARNING —A Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal tab on the inside of the control panel.

75-5148B (Bolt) 160013-001 VERTICAL-MOTION PCB: (Leaf switch/button holder) 178030-003 BLACK, RED, YELLOW, (Brack button) and GREEN WIRES.

75-9415, 1-PLAYER START (Nut)

fy S-

036895-01 (Switch bezel)

—,, 62-039 (LED switch)

A038038-01 Midi Trak-Ball™ Assy. See Figure 3-5 > Sy SS HORIZONTAL-MOTION PCB: BLUE, VIOLET, RED, and BLACK WIRES

A039261-01 (Harness) 2-PLAYER START A039346-01 (Control panel/decal) mS 039343-01 SS (Control panel) 039315-04 (Oecal—not shown)

1 PLAYER START 2 PLAYER START A039444-01 (Control panel/decal) WHITE/BLACK —i mi werereo l=) | 039445.01

  • (Contro} panel) RED +) _t BROWN RED(+) ORANGE 039446-04 ts L5y (Normally open (Normally open (Decal—not shown) contact) contact) BLACK BLACK (Common contact) «Common contact}

Figure 3-4 Control Panel Assembly Upright Cabinet A039308-01 A lreland-Built Cabinet A039443-01 A

3-7

Page 30

Maintenance, Repair, and Parts Millipede™

Control Panel Assembly Parts List

Assemblies and components in the following parts list are shown in Figure 3-4.

Part No. Description Upright Cabinet A039346-01 Control Panel with Decal 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x ¥-Inch Thick (not shown—24 inches required) 039315-04 Control Panel Decal (not shown) 039343-01 Control Panel lreland-Built Cabinet A039444-01 Control Panel with Decal 039445-01 Control Panel 039446-04 Control Panel Decal (not shown)

Upright and Ireland-Built Cabinets A038038-01 “DD Midi Trak-Ball™ Assembly A039261-01 Control Panel Harness Assembly 62-039 SPDT Momentary Pushbutton Start Switch with Red Light-Emitting Diode 75-9415 #10-24 Self-Locking Nut 75-5148B #10-24 Black Carriage Bolt 036895-01 Black Molded Switch Bezel 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-003 Black Pushbutton Assembly

3-8

Page 31

Miltipede™ Maintenance, Repair, and Parts

SCREWDRIVER OR PIN @ S 176010-106 038039-01 (Screw) (Upper frame)

On HOLE IN SHAFT

ENCODING WHEEL

LUBRICATE HERE (Six places) GA) ALLEN WRENCH

038043-01 | SOCKET-HEAD @ (Mid! Trak-Bal) ® oan

035937-01 ‘Gall bearing) 03804201 oY (idler shat) *" 038041-04 Circled numbers match num- (Roller shaft) bered instructions. Disassemble in the order indicated.

@ 035938-01 (Encoding wheel)

© 75.0145 \ (Flat washer) —_| © rs0us oo (Split-lock washer) — © r206 —+f (Hex screw) VERTICAL-MOTION PCB: BLACK, RED, YELLOW, and GREEN WIRES

A036096-01 (Harness assy.)

199002-001 (Optical coupler—

  • hidden trom view) HORIZONTAL-MOTION PCB: BLUE, VIOLET, RED, and BLACK WIRES

A035220-02 {Coupler PCB assy.) ©

Figure 3-5 Midi Trak-Ball™ Assembly A038038-01 A

3-9

Page 32

Maintenance, Repair, and Parts

Am warnins —£y Switch the game to off before removing or repairing the Midi Trak-Ball.

Lubricating the Midi Trak-Ball™

  • Remove the entire Midi Trak-Ball™ assembly from the control panel (see Figure 3-4). Remove the six screws that secure the upper and lower frames together (see Figure 3-5).
  • _ Lift off the top frame.
  • Lubricate each of the six ball bearings with two drops of a light-duty oil, such as 3-in-One oil. Lubricate the bearings approximately every three months or 6,000 credits (credits are counted on the coin counter).

Removing the Midi Trak-Bali™ Coupler PCB, and Encoding Wheel:

  • Follow steps 1 and 2 above. Then remove the Midi Trak-Ball™.
  • Lift the PCB out of its slot. Carefully disconnect the red connector and remove the PCB. Millipede™

Remove the socket-head screw, fiat washer, and splitlock washer that secure the encoding wheei. Remove the encoding wheel. Reassemble and reinstall in reverse order.

NOTE When you replace the PCB, make sure that the metal encoding wheel is not bent or damaged. It should turn freely between the two halves of the radial optical coupler.

Adjusting the Midi Trak-Ball™ Control:

9.

10.

1. When you tighten the encoding wheel, rotate the socket-head screw on the end of the roller shaft until a hole in the shaft is visible through the hole in the top of the frame. Insert a 3/10-inch diameter pin or screwdriver through the hole in the shaft. Tighten the socket-head screw with an Allen wrench.

Midi Trak-Ball™ Assembly Parts List

Part No. Description

A035220-02 Coupler PCB Assembly (includes Radial Optical Coupler) A036096-01 Harness Assembly 72-8406 #4-40 x ¥-Inch, Hex Socket-Head Steel Machine Screw 75-014S #4 Flat SAE-Standard, Zinc-Plated Steel Washer

75-044S #4 Split-Lock, Zinc-Plated Steel Washer 034168-01 Label with Lubrication Instructions (not shown) 035937-01 Ball Bearing (6 per assembly) 035938-01 Etched Encoding Wheel 038039-01 Upper Black Plastic Frame 038040-01 Lower Black Plastic Frame 038041-01 Roller Shaft - 038042-01 \dler Shaft 038043-01 Midi-Trak-Ball_ (3-inch diameter) 139002-001 Radial Optical Coupler (located on the Coupler PCB Assembly) 176010-106 #8 x %-Inch Cross-Recessed, Pan-Head, Zinc-Plated Steel Screw

3-10

Page 33

Mitlipede™ Maintenance, Repair, and Parts

  • Remove the cardboard locking tab at each end of the
Cc.Fluorescent Tube,tube. Slightly rotate the tube up or down, and carefully

remove it from the tube holders.

Speaker,and Attrac-3.Replace it with a new tube. Do not snap in the tube vig-

orously—you may break it, causing an implosion! Re-

tionPanelplace the locking tabs.
  • Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start. Reinstall in reverse order. Bem warning Ady Before you remove or repair the fluorescent tube or speaker, switch the the game to off.

\f you drop a fluorescent tube and it breaks, it H will implode! Shattered glass can fly six feet or Upright Cabinet more from the implosion. Use care when re- Replacing the Speakers: placing any fluorescent tube.

  • Remove the four screws and lock washers that secure the speaker grille to the cabinet and remove the speaker grille (see Figure 3-7).
  • Remove the four screws that secure the speaker to the Upright Cabinet cabinet. Replacing the Fluorescent Tube: 3. Hold the speaker securely with one hand and disconnect the two plug-in connectors on the back of the
  • Remove the three screws and lock washers that se- speaker. Note that the white wire (+) connects on the cure the attraction-panel assembly to the cabinet, and side marked with a painted dot. Replace the speaker remove this assembly (see Figure 3-6). and reinstall in reverse order.

142028-xxx 99-11003 A005493-01 ‘A037540-01 (Transformer) (Starter) (Hames)

@. (Ground wire) 179035-001 (Tube holder)

(Panel)

99-11006 (Tab) ys Wid : 037469-01 03931306 7~ JAA & / (Bracket)

(Decal)Ae‘osesasi

039318-01 Sy (Retainer) (Shiela Circled numbers match the numbered instructions. Disassemble in the order indicated.

NOTE

To make sure that the fluorescent tube starts, check that the ground wire is firmly attached to the ballast transformer.

Figure 3-6 Fluorescent Tube and Attraction Panel Upright Cabinet A039305:01 A and A039307-01 A

Page 34

Maintenance, Repair, and Parts Millipede™

Fluorescent Tube, Speaker, and Attraction Panel Assemblies Upright Cabinet Parts List Assemblies and components in the following parts lists are shown in Figures 3-6 and 3-7

Part No. Description A005493-01 Fluorescent Tube Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 78-6900402 Viny! Foam Single-Coated Adhesive Tape, %4-Inch Wide x Inch Thick (24 inches required) 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (tab consists of two pieces) 99-11009 Starter Socket

037469-01 Steel Tube Bracket 039313-04 Attraction Panel Decal 039314-04 Speaker Grille Decal 039318-01 Attraction Panel Shield 039323-05, Attraction Panel (does not include shield or decal) 039344-01 Speaker Grille 039345-01 Attraction Panel Retainer 148001-017 6 x 9-Inch Oval, 8-Ohm, 6-Ounce, Shielded High-Fidelity Speaker 142028-001 60 Hz, 118 V, Ballast Transformer (used on A038504-01 assembly) 142028-002 50 Hz, 118 V, Ballast Transformer (used on A038504-02 assembly) 179035-001 2-Pin Fluorescent Tube Holder

Circled numbers match the numbered instructions. Disassemble in the order indicated. 039314-04 (Decal)

03934401 (Grille)

148001-017 (Speaker)

Figure 3-7 Removing the Speaker Upright Cabinet

3-12

Page 35

Millipede™ Maintenance, Repair, and Parts

  • Disconnect the two speaker connectors. Note that the white wire (+) connects on the side of the speaker marked with a painted dot
  • Remove the screws that attach the speaker to the panel. Replace the speaker. Reassemble in reverse order. A— warning Ady Before you remove or repair the fluorescent tube or speaker, switch the the game to off. If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly six feet or more from the implosion. Use care when replacing any fluorescent tube.

lreland-Built Cabinet

Replacing the Fluorescent Tube: lreland-Built Cabinet

Replacing the Speaker:

1.Remove the three screws and flat washers that secure©.Gerfonn steps:ang 2iabewe. Remove:the lead con:

7 ° nectors at each end of the tube. the top of the attraction panel to the cabinet (see .

Figure 3-8).6.Replace with a new tube. Do not snap in the tube

vigorously—you may break it, causing an implosion!

  • Grasp the panel at the top edge and pull it forward (be Replace the Y-lead connectors. careful not to damage the speaker that is attached .
under the grille). Lift the panel up and out of the7.Reassemble in reverse order.

cabinet.

039442-04 (Decal) 035835-01 99-11003 99-11009 (Y-lead connector) (Starter) (Socket)

142028-002 (Transformer) 148001-001 (Speaker) A038856-01 (Harness)

(Shield)

99-11012 038978-01 038987-01 (Clamp) (Board) Grille)

038977-05 (Panel) NOTE

Circled numbers match num- To make sure that the fluorescent tube starts, bered instructions. Disassemble check that the ground wire is firmly attached in the order indicated. to the ballast transformer.

Figure 3-8 Fluorescent Tube, Speaker, and Attraction Panel lreland-Built Cabinet

3-13

Page 36

Maintenance, Repair, and Parts Millipede™

Fluorescent Tube, Speaker, and Attraction Panel lreland-Built Cabinet Parts List

Assemblies and components in the following parts list are shown in Figure 3-8,

Part No. Description A038856-01 Tube and Speaker Harness Assembly 70-303 18-Inch, 15-W, Cool White Fluorescent Tube 99-11003 Fluorescent Tube Starter 99-11009 Starter Socket 99-11012 1 Inch Fluorescent Tube Clamp. 035835-01 12-Inch Y-Lead Connector 039442-04 Attraction Panel Decal 038977-05 Speaker/Attraction Panel 038987-01 Speaker/Attraction Panel Grille 038989-01 Attraction Panel Shield (does not include decal) 142028-002 50 Hz, 118 V, Ballast Transformer 148001-001 6 x 9-Inch Oval, 4-Ohm, 6-Ounce, Shielded High-Fidelity Speaker

3-14

Page 37

Millipede™

D. Video Display

Ay WARNING =e SHOCK HAZARD

yoke can fly six feet or more from the implosion. Use care when replacing any display.

039320-01 039317-01 (Bezel) (Shield) Maintenance, Repair, and Parts

Upright Cabinet Removing the Video Display:

The following procedure should only be per-1.From the back of the cabinet, open the rear access

formed by a qualified service technician. panel. Unplug the display harness connectors and dis- Before removing or repairing the video display, connect the ground wire (see Figure 3-9).

switch the game to off. As an extra precaution,2.Remove the hardware that secures the display chassis

we highly recommend you discharge the high to the rear bracket. voltage from the picture tube. .

.a..3.Open the control pane! (see Figure 3-3).

High voltages may exist in any video display, . . . a .

even with power disconnected. Use extreme4.Grasp the video display shield and slide it down into
caution and do not touch electrical parts of the the cut-out area below the shield. Tilt the shield fordisplay with your hands or with metal objects ward and lift it up and out of the cabinet.
in your hands!5.Remove the cardboard bezel.

IMPLOSION HAZARD 6. Remove the four sets of hardware that secure the vid- If you drop the display and the picture tube £0 display to the cabinet.

breaks, it will implode! Shattered glass and the7.Carefully remove the display through the front of the

cabinet. Place it on a soft mat in a protected location. After servicing the display, reinstall it in reverse order.

Circled numbers match the numbered instructions. Disassemble in the order indicated.

037750-01 (Bracket)

038805-01 (Retainer)

139003-1004 (Matsushita display) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbidden without the specihic written permission of Atan, Inc. Sunnyvale, CA This drawing is only condtionally issued. and ‘neither recerpt nor possession thereot conters or translers any right in, or license to use. the subject matter ol the drawing ef any design or technical intorma: tion shown thereon. nor any right to reproduce this drawing 7 any part thereot Except for manulacture by vendors of Atar Inc. and tor manulacture under the corporation's wien license 19 right to reproduce Ihis drawing 's granted or the subject mat: ter thereot unless by written agreement with or written permis. sion from the corporation

Figure 3-9 Video Display Upright Cabinet

3-15

Page 38

Maintenance, Repair, and Parts

A WARNING meh

The following procedure should only be performed by a qualified service technician. Before removing or repairing the video display, switch the game to off. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube. High voltages may exist in any video display, even with power disconnected. Use extreme

caution and do not touch electrical parts of the display with your hands or with metal objects in your hands! IMPLOSION HAZARD If you drop the display and the picture tube breaks, if will implode! Shattered glass and the yoke can fly six feet or more from the implosion. Use care when replacing any display. Millipede™

lreland-Built Cabinet Removing the Video Display:

  • From the back of the cabinet, open the rear access panel. Unplug the display harness connectors and disconnect the ground wire (see Figure 3-10).
  • Remove the hardware that secures the display chassis to the rear bracket.
  • From the front of the cabinet, open the contro! panel (see Figure 3-3).
  • Grasp the metal retainer that holds the bottom of the video display shield and slide the retainer and the shield down and out of the cabinet.
  • Remove the cardboard bezel.
  • The display is secured to the cabinet with metal brackets. Remove the four sets of hardware that secure the display to these brackets.
  • Carefully pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall it in reverse order.

3-16 A039018-01 ® "Gere 038992-01 (Shield) Circled numbers match the numbered instructions. Disassemble in the order indicated.

038790-01 (Bracket)

  • aN o a 039009-01 (Bracket)

Figure 3-10 Video Dispiay lreland-Built Cabinet

Page 39

Video Display Upright and Ireland-Built Cabinets Parts List

Assemblies and components in the following parts list are shown in Figures 3-9 and 3-10.

Part No. Description For Upright Cabinet 037750-01 Display Support Bracket 039317-01 Display Shield 039320-01 Display Bezel 139003-1004 19-Inch Matsushita Color Raster-Scan Display For Ireland-Built Cabinet 039018-01 Display Bezel 038790-01 Front Display Support Bracket 038805-01 Display Shield Retainer 038992-01 Display Shield 039009-01 Rear Display Support Bracket 139003-1004 19-Inch Matsushita Color Raster-Scan Display Acceptable substitute is part no. 92-049

3-17

Page 40

Maintenance, Repair, and Parts Millipede™

E. Utility Panel

  • WARNING == Before removing or repairing the utility panel, switch the game to off.
NOTE

Only the Ireland-Built cabinet has two coin counters.

Players may receive an electric shock if the utility panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal screw on the back of the coin counter. The utility panel is located inside the upper coin door. This panel includes the volume control, self-test switch, auxiliary Coin switch, and the coin counter(s). The coin switch is used to credit the game without activating the coin counter.

A038004-01 i“ (Harness) A002465-01 (Coin counter)

038003-01 (Bracket)

62-041 (Auxiliary coin switch)

19-9032 (Volume control)

69-001 (Self-test switch)

178070-001 (Volume control knob)

Figure 3-11 Utility Panel Assembly A038002-01 & -02 F Parts List

Part No. Description

A002465-01 6 V Coin Counter A038004-01 Utility Panel Harness 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap

69-001 DPDT Self-Test Switch 038003-01 Utility Panel Bracket 178070-001 Volume Control Knob

3-18

Page 41

Millipede™ Maintenance, Repair, and Parts

F. Coin Door

170000-001 (Lamp) 179047-001 99-15023 (Lamp Base) (Base Plate)

oo 99-15056 99-15026 (Screw for Bezel) (Coin Inlet) 99-15025 Be (Coin Inlet)

(Pivot for Lever) a

ae 99-15068 en (Lockout Coil) 9945069 (Lockout < Coil Spring)

99-15030 @@ a4 PS é (Lockout Flap)

75-9148 (Hex Nut)

(Lock Wash.)

9915075 | (Sw. Adjuster)

99-15029 (Bracket) (Sw. Cover}

‘Switch)

T24414S (Screw)

Figure 3-12 Vertically Mounted Coin Door Assembly A037619-xx D

3-19

Page 42

Maintenance, Repair, and Parts

A037542-01 (Harness—not shown)

99-15063 (Screw)

99-15067 (Lock Assy.)

*

038091-01 (Coin Box)

99-15072 (Door Frame)

9915073 (Upper Door)

99-15074 (Lower Door)

A037619-01 — U.S. 25¢/25¢ Coin Door ‘A037619-02 — U.S. 508/50 Coin Door ‘A037619-03 — Canadian 25¢/25¢ Coin Door A037619-04 — British 10 P/10 P Coin Door A037619-05 — British 10 P/50 P Coin Door A037619-06 — British 20 P/50 P Coin Door ‘A037619-07 — Australian 20¢/20¢ Coin Door 99-15070 (Doors and Frame)

A037619-08 — German 1 DM/1 DM Coin Door ‘A037619-09 — German 2 DM/1 DM Coin Door A037619-10 — German 2 DM/5 DM Coin Door ‘A037619-11 — German 1 DM/5 DM Coin Door A037619-12 — § Fri5 Fr Coin Door A037619-13 — Swiss 1 Fr/1 Fr Coin Door A037619-14 — French 1 Fri1 Fr Coin Door Millipede™

99-15038 (Bezel for Button)

99-15001 thru $9-15011 (Return Button)

99-15052 z (Spring for Button)

99-15039 (Bezel for Cover)

99-15036 (Cover)

99-15066 (Screw)

A037619-15 — French 2 Fr/1 Fr Coin Door A037619-16 — Swedish 1 Kr/1 Kr Coin Door ‘A037619-17 — Spanish 25 Pts!25 Pts Coin Door ‘A037619-18 — Italian 100 L/100 L Coin Door A037619-19 — Hong Kong $1/$1 Coin Door A037619-20 — Japanese 100Y/100Y Coin Door

Figure 3-12 Vertically Mounted Coin Door Assembly, continued

3-20 A037619-xx D

Page 43

Millipede™ Maintenance, Repair, and Parts

Vertically Mounted Coin Door Parts Lis:

Assemblies and components in the following parts list are shown in Figure 3-12.

Part No. Description A037542-01 Harness Assembly 7214148 #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9148 #4-40 Stee! Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006. Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Iniet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056. #4-40 x %,-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066, Screw for Clamp 99-15067 Lock Assembly 99-15068 Lockout Coil 99-15069 Spring for Lockout Coil 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly) Acceptable substitute is part number A037491-01 170000-001 6.3V Miniature Wedge-Base Incandescent Lamp 171006035 Metal Coin Mechanism 179047-001 Lamp Base

3-21

Page 44

Maintenance, Repair, and Parts

G. Printed-Circuit Boards

A— warninc—A, Before you remove or repair any printed-circuit board (PCB), switch the game to off.

Removing the Printed-Circuit Boards:

1.

2. Open the rear access panel. The Upright game PCB is located inside the electromagnetic interference (EMI) cage (see Figure 3-13). Unplug the two edge connectors on the EMI shield PCB. To remove the PCB, pull the eight nylon snap-in fasteners on the EMI shield PCB to the unlocked position. Carefully slide the shield PCB with attached game PCB straight out of its guide. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required, and reinstall the PCBs. Millipede™

To remove the /reland-Built game PCB, remove the screw and two washers that secure the PCB to the cabinet. Carefully slide the PCB straight out of its retainer. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required, and reinstall the PCB. To remove the Regulator/Audio |! PCB, first disconnect the five small harness connectors on this board. Remove the hardware that secures the Regulator/Audio || PCB to the cabinet, and carefully remove the board from its retainer. Do not twist the board, as this may loosen connections or components. Replace or repair as required, and reinstall the PCB.

CAUTION

Make sure that the connectors on each PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.

Close and lock the rear access panel.

Important: Perform the self-test.

Game PCB Removal “OD — from EMI Cage -

NOTE

The Federal Communications Commission requires that the game PCB be housed in the EMI cage with the Shield PCB attached.

A037701-01 (Cage)

72-4604F ‘Screw 72-4404F \ (Screw) GAME PCB

>

037873-01 (Spacer) EMI SHIELD PCB 038178-03, (Retainer)

176015-110 (Screw)

A038874-21 (Millipede™ game PCB)

A039490-01 (Shield PCB)

175009-221 Le (Spacer) SS 178045-442 (Fastener) 178044-242 (Grommet)

Figure 3-13 Removing the Printed Circuit Boards (PCBs)

3-22

Page 45

Millipede™ Maintenance, Repair, and Parts

Regulator/Audio Il PCB Removal Game PCB Removal Without EMI Cage

72.6810S (Screw) 72.6810S 175004-708 (Screw) 176016-110 (Washer) (Screw)

034536-02 (Foam pad)

175004-708 A035435-02 (Washer) (Regulator! Audio 1! PCB)

Figure 3-13 Removing the Printed Circuit Boards (PCBs)

Printed-Circuit Board Mounting Hardware Parts List

Assemblies and components in the following parts list are shown in Figure 3-13.

Part No. Description

Upright Cabinet A037701-01 Electromagnetic Interference (EMI) Cage (includes guide) A039490-01 EMI Shield PCB 72-1404F #4-40 x Va-Inch Cross-Recessed Steel Screw 72-1604F #6-32 x Ya-Inch Cross-Recessed Stee! Screw 037873-01 Spacer 038178-03 Dual-Slotted Retainer 175009-221 Plastic Spacer 176015-110 #10 x %-Inch Cross-Recessed Pan-Head Screw

178044-242 Grommet 178045-442 Snap-In Fastener Plastic Guide

Upright and Ireland-Built Cabinets

72-6810S. #8 x 5,-Inch Cross-Recessed Pan-Head Screw 034536-02 Foam Pad 175004-708 #8 Fiber Washer

3-23

Page 46

Millipede™ Maintenance, Repair, and Parts

NOTICE TO ALL PER!

CONFIDENTIAL: Reprod sion from the corporation : 7 ae A: A “ " “2 ge & " js fi

fous] ass] ers) SRF = ' feaszs) ee?) Seer] Sima —_.

[eseaca-o1 i! i) erry) =

fzs2ee] 1 &s2s) Sera] Veaae {isa7a] 2245] 39) aa]

Ss a eng ss ca) I {= = a feos] aaa]

= bas fe) eee) Ese tee] fo39] 7a] Ser |

fon (Ss3) Game) see] aa] =) es] jzona| t =a cs273 | pasea} s87] \ererees fsa] pana} , ——— [=] fen) fsa) fons ps] saome! [sess ceca : caer] fee] See] Sw)

a rere ==) Tay es faa] pre Seer] aa 4 ¥ an q i “eee i ae) pee! \ oe a oT Se a 2 tb or 6 8 Z 9 s ’ £ z '

A038874-21 B Figure 3-14 Millipede™ Game Printed-Circuit Board Assembly

3-24

Page 47

Millipede™ Maintenance, Repair, and Parts

Millipede™ Game Printed-Circuit Board Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

C10.1 uF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104
c2100 pF, 100 V, Mica Epoxy-Dipped Radial Lead Mica Capacitor128002-101
C339 pF, 100 V, Epoxy-Dipped Radial Lead Mica Capacitor128002-390
C4-C120.1 uF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104
C131000 pF, + 20%, 50 V Minimum Ceramic Capcitor122009-102
C14-C221 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500105
C231000 pF, + 20%, 50 V Minimum Ceramic Capcitor122009-102
C241 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500105
C25-C300.1 uF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104
C31, C3210 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500106
C3347 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500476
C3410 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500106
C350.1 uF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104
C36, C370.22 uF, 25 V Ceramic-Disc Radial-Lead Capacitor122008-224
C380.1 uF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104
C39100 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350107
C401 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24500105
C410.1 uF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104
C422.2 uF, + 20%, 35 V Tantalum Capacitor122000-225
C43100 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350107
C441 uF, + 10%, 35 V Axial-Lead Tantalum Capacitor29-006
C45,0.1 uF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104
C46100 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350107
C47-C540.01 uF, 25 V Ceramic-Disc Radial-Lead Capacitor122005-103
C55-C620.1 uF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104
C630.22 uF, 25 V Ceramic-Disc Radial-Lead Capacitor122008-224
C64-C1040.1 uF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104

Diodes

CR1-CR580 V, Type-1N100 Diode31-1N100
CR6Type-MV5053 Light-Emitting Diode38-MV5053.

Integrated Circuits

1BType-74LS42 Integrated Circuit37-74LS42
1C/D, 1D/E, 1FType-74LS244 Integrated Circuit37-74LS244
ARType-74LS174 Integrated Circuit37-74LS174
2cType-6502B Microprocessor90-6012
2NType-74LS175 Integrated Circuit37-74LS175
3EType-74LS139 Integrated Circuit37-74LS139
3FType-74LS42 Integrated Circuit37-74LS42
3HType-74LS74 Integrated Circuit37-74LS74

(Continued on next page)

3-25

Page 48

Maintenance, Repair, and Parts

Millipede™ Game Printed-Circuit Board Assembly Parts List, continued Millipede™

DesignatorDescriptionPart No.
3J-3MType-74LS153 Integrated Circuit37-74LS153
3NType-74LS374 Integrated Circuit37-74LS374
3PType-74LS244 Integrated Circuit37-74LS244
4BAudio I/O N-Channel MOS/LSI Custom Integrated Circuit01229401
4DAudio 1/0 N-Channel MOS/LSI Custom Integrated CircuitC012294-01
4EType-74LS245 Integrated Circuit37-74LS245
4FType-74LS32 Integrated Circuit37-74LS32
4HType-74LS139 Integrated Circuit37-74LS139
4JType-74LS153 Integrated Circuit37-74LS 153
4PType-74LS373 Integrated Circuit37-74LS373
4R, 5EType-74LS273 Integrated Circuit37-74LS273
SFType-74LS10 Integrated Circuit37-74LS10
5HType-74LS08 Integrated Circuit37-74LS08
5dType-74LS257 integrated Circuit37-74LS257
5KType-74LS157 Integrated Circuit37-74LS 157
5L.Type-74LS166 Integrated Circuit37-74LS166
5M, 5NType-74LS157 Integrated Circuit37-74LS157
6CType-74S04 Integrated Circuit37-74S04
6D-6FType-74LS163A Integrated Circuit37-74LS 163A
6H, 6JType-74LS83 Integrated Circuit37-74LS83
6KType-74LS20 Integrated Circuit37-74LS20
6LType-74LS174 Integrated Circuit37-74LS174
6MType-74LS157 Integrated Circuit37-74LS157
6NType-74LS86 Integrated Circuit37-74LS86
6P, 6RType-74LS157 Integrated Circuit37-74LS157
7BType-74S153 Integrated Circuit137207-001
7C, 7DType-74LS163A Integrated Circuit37-74LS 163A,
7FType-74LS32 Integrated Circuit37-74LS32
7HType-74109 Integrated Circuit37-74109
7J, 7KType-74LS273 Integrated Circuit37-74LS273
7NType-74LS157 Integrated Circuit37-74LS157
7PType-74LS86 Integrated Circuit37-74LS86
7RType-74LS166 Integrated Circuit37-74LS 166
8C, 8DType-74LS163A Integrated Circuit37-74LS 163A,
8EType-74LS175 Integrated Circuit37-74LS175
8FType-74LS14 Integrated Circuit37-74LS14
8HType-74LS74 Integrated Circuit37-74LS74
8JType-74S153 Integrated Circuit137207-001
8NType-74LS191 Integrated Circuit37-74LS191
9BType-74LS273 Integrated Circuit37-74LS273
9cType-74LS157 Integrated Circuit37-74LS 157,
9DType-74LS32 Integrated Circuit37-74LS32
gEType-74LS08 Integrated Circuit37-74LS08
OFType-74LS90 Integrated Circuit37-74LS90

3-26 (Continued on next page)

Page 49

Millipede™

Millipede™ Game Printed-Circuit Board Assembly Parts List, continued Maintenance, Repair, and Parts

DesignatorDescriptionPart No.
9H, QJType-74LS74 Integrated Circuit37-74LS74
9M, 9NType-74LS257 Integrated Circuit37-74LS257
9PType-74LS191 Integrated Circuit37-74LS191
10CType-74LS157 Integrated Circuit37-74LS157
10DType-74LS74 Integrated Circuit37-74LS74
10EType-74LS00 Integrated Circuit37-74LS00
10FType-555 Timer Integrated Circuit37-555
10K, 10LType-74LS257 Integrated Circuit37-74LS257
10NType-4584B Hex Schmitt Trigger Integrated Circuit37-4584B
10PType-74LS157 Integrated Circuit37-74LS157
40RType-74LS74 Integrated Circuit37-74LS74
11FDual Operational-Amplifier Integrated Circuit37-347
41HQuad Operational-Amplifier Integrated Circuit37-TLO82CP
iPType-4584B Hex Schmitt Trigger Integrated Circuit37-4584B
124Type-74LS273 Integrated Circuit37-74LS273
12BType-74LS157 Integrated Circuit37-74LS157
12C, 12DType-7407 Integrated Circuit37-7407
12EType-74LS259 Integrated Circuit37-74LS259

Programmable Read-Only Memories

4HErasable Programmable Read-Only Memory136013-101
WKErasable Programmable Read-Only Memory136013-102
MLErasable Programmable Read-Only Memory136013-103
41MINErasable Programmable Read-Only Memory136013-104
7EProgrammable Read-Only Memory136001-213

Random-Access Memories

2E, 2FRandom-Access Memory90-7033
2J-2MRandom-Access Memory Acceptable substitute is part137250-001

no. 137250-002

AK-4NRandom-Access Memory Acceptable substitute is part137250-001

no. 137250-002

88Random-Access Memory Acceptable substitute is part no.137178-001

137271-001

10A, 10BRandom-Access Memory90-7005
11B, 110Random-Access Memory90-7005,

Read-Only Memories

2P.Electrically-Alterable Read-Only Memory137161-001
SPRead-Only Memory136013-109
5RRead-Only Memory136013-110

(Continued on next page)

3-27

Page 50

Maintenance, Repair, and Parts

Millipede™ Game Printed-Circuit Board Assembly Parts List, continued Millipede™

DesignatorDescriptionPart No.

Resistors

Ri, R210 KQ, +5%, % W Resistor110000-103
R3220 2, +5%, Vv W Resistor110000-221
R41 KQ, +5%, % W Resistor110000-102
RS10 KQ, +5%, Y W Resistor110000-103
R622 KQ, +5%, 4 W Resistor110000-223
R71 KQ, +5%, % W Resistor110000-102
R8220 Q, +5%, V4 W Resistor110000-221
R9-R191 KQ, +5%, % W Resistor110000-102
R20-R27470 Q, +5%, Vs W Resistor110000-471
R28-R431 KQ, +5%, % W Resistor110000-102
R44-R46470 Q, +5%, V4 W Resistor110000-471
R476.8 KQ, +5%, % W Resistor110000-682
R48470 Q, +5%, % W Resistor110000-471
R491 KQ, +5%, % W Resistor110000-102
R50, R5118 KQ, +5%, % W Resistor110000-182
R52100 2, +5%, % W Resistor110000-101
R536.8 KQ, +5%, v4 W Resistor110000-682
R54470 Q, +5%, V4 W Resistor110000-471
RSS1 KQ, +5%, % W Resistor110000-102
R561.8 K2, +5%, % W Resistor110000-182
R57100 2, +5%, % W Resistor110000-101
RS86.8 KQ, +5%, % W Resistor110000-682
R59470 Q, +5%, V4 W Resistor110000-471
R601 KQ, +5%, % W Resistor110000-102
R61, R621.8 K2, +5%, %4 W Resistor110000-182
R63100 2, +5%, ¥% W Resistor110000-101
R64-R66270 Q, +5%, % W Resistor110000-271
R70-R76470 Q, +5%, V4 W Resistor110000-471
R77-R831 KQ, +5%, % W Resistor110000-102
R84-R913.3 KQ, +5%, V4 W Resistor110000-332
R92-R10810 KQ, +5%, v4 W Resistor110000-103
R109, R1101 KQ, +5%, % W Resistor110000-102
R111, R112220 2, +5%, v4 W Resistor110000-221
R113-R119470 2, +5%, v4 W Resistor110000-471
R120-R15210 KQ, +5%, %4 W Resistor110000-103
R153220 2, +5%, v4 W Resistor110000-221
R154100 KQ2, +5%, % W Resistor110000-104
R1651 KQ, +5%, % W Resistor110000-102
R156-R15839 KQ, +5%, % W Resistor110000-393
R159220 2, +5%, % W Resistor110000-221
R16068 KQ, +5%, % W Resistor110000-683
R161, R1621 KQ, +5%, 1% W Resistor110000-102
R163470 2, +5%, V4 W Resistor110000-471
R16410 Ke, +5%, %4 W Resistor110000-103

(Continued on next page}

3-28

Page 51

Millipede™ Maintenance, Repair, and Parts

Millipede™ Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R16539 KQ, +5%, ¥4 W Resistor110000-393
R166-R1701 KQ, +5%, % W Resistor110000-102
R171, R1721.8 KQ, +5%, % W Resistor110000-182

Sockets

1H, 1L, 1M/N24 Contact, Medium-Insertion-Force IC Socket79-42C24
2c40 Contact, Medium-Insertion-Force IC Socket79-42C40
2P.22 Contact, Medium-insertion-Force IC Socket79-42C22
4B, 4D40 Contact, Medium-Insertion-Force 1C Socket79-42C40
5P, 5R24 Contact, Medium-Insertion-Force IC Socket79-2024

Switches

5B, 5D, 8P.8-Station, Single-Throw, Dual-Inline-Package Bit Switch66-118P1T

Transistors

Q1-Q4Type-2N3904, 60 V, 1 W, NPN Transistor34-2N3904
Q6, Q7Type-2N6044 Darlington NPN Transistor34-2N6044

Miscellaneous

L1-L3100 wH Inductor Acceptable substitute is part no. 41-3003141002-001
VR1Voltage Regulator37-7815
VR2Voltage Regulator37-7915,
Y112.09 MHz Crystal144000-001

Test Point Acceptable substitute is part no. 020670-01 17905 1-002 Nylon Snap-In Fastener 81-4302

3-29

Page 52

Maintenance, Repair, and Parts Millipede™

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING r CONFIGENTIAL. Reproducion farbden winout ine epee R33 wotten permission of ate in Sunnyvale. CA This drawing is {eee} iy ‘condianaly issued. and neler recep nor poseescon fhereot conters or sranslers ary ng Ino” lense fo use: The > +o. 2

Subject mater ofthedrawing tary design or fecical osm9ERED,
Won shown sheteon, nor any tf reptaduce tie raat oFCc)aor 4Q
ine and for manutacture under tne Corporation's miiten license12)—sR7820
no fight to reproduce this drawing is granted of the subject mat-CRS-

Ter mereot unless by witien agigonen wil or weillen perms

Sion rom the Corporatonco0
c20cal0

ap)

+3300| —

35V

—3309+}-—

35V 0

P32 5.6K

a

Oo38fees wee)
TIP32_TOAZ0024TOA2002A
tageINACo2 O57iaia
R5cee*]8Sts
eet.C78 cc coats
0S3}R3 elo CGE)oes}cis)
Cet{-|*mamaria JOS,Re2Gge oy
ge)RSHes11220] R21, aw

BAe "|

laE|che
0-§seSeEE4SMee
zh SBosean470,
a Regereyoak
clo4pCAGoci
470470 +CeFRI

7 ey iT} 3 Ci | TT | Rott 10

S|9+3300ur+}
-{22035V

R30 RI 1/2W OD cr:

OF insooz0=)0

ae]

UO%—|+3300uFj—
4@35V

Figure 3-15 Regulator/Audio II Printed-Circuit Board Assembly A035435-04 C

3-30

Page 53

Millipede™ Maintenance, Repair, and Parts

Regulator/Audio I| Printed-Circuit Board Assembly Parts List

Components in the following parts list are shown in Figure 3-15.

DesignatorDescriptionPart No.

Capacitors

C1470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C30.1 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104
C4470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C50.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable100015-103

substitute is part no. 122005-103

Ccé0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
c70,001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C80.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C9, C103300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338,
ci0.1 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104
C12470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C131000 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108
C140.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead CapacitorAccept-100015-103

able substitute is part no, 122005-103

C150.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C170.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338,
C20, C210.1 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104

Diodes

CR1, C4Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR5-CR8Type-1N5401, 3 A, 100 V Silicon Rectifier Diode31-1N5401

Integrated Circuits

QiType-LM305, 5 V, Linear Voltage Regulator37-LM305
Q5Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002
Q7Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002

(Continued on next page)

3:31

Page 54

Maintenance, Repair, and Parts Millipede™

Regulator/Audio I! Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.

Resistors

R1270 Q, +5%, v4 W Resistor110000-271
R333 Q, +5%, v4 W Resistor110000-330
R4100 2, +5%, % W Resistor110000-101
RS2.7 Q, +5%, 1 W Resistor110009-027
R63.9 kQ, +5%, % W Resistor110000-392
R775 kQ, +5%, Vs W Resistor110000-752
R81k& Horizontal PCB-Mounting Cermet Potentiometer Acceptable119002-102

substitute is part no. 19-315102

RQ220 2, +5%, v2 W Resistor110001-221
R1012, +5%, % W Resistor110000-010
R1110 2, +5%, v4 W Resistor110000-100
R12100 2, +5%, % W Resistor110000-101
R13, R1410 k2, +5%, % W Resistor110000-103
R191Q, +5%, % W Resistor110000-010
R2010 Q, +5%, v4 W Resistor110000-100
R21220 Q, +5%, v2 W Resistor110001-221
R22100 2, +5%, % W Resistor110000-101
R240.1, +3%, 7 W Wirewound Resistor19-100P1015
R27, R281kQ, +5%, Va W Resistor110000-102
R29, R3010 2, 5%, Y% W Resistor110000-100
R32, R335.6 kQ, +5%, % W Resistor110000-562

Transistors

Q2TypeTIP32 PNP Power Transistor33-TIP32
Q3Type-2N3055 NPN Silicon Transistor34-2N3055,

Mechanical Parts

J66-Position Connector Receptacle79-58306
J79-Position Connector Receptacle79-58308
J84-Position Connector Receptacle79-58354
Jo6-Position Connector Receptacle79-58306
J1012-Position Connector Receptacle79-58346
Q2#6-32 x ¥4-Inch Binder-Head Nylon Screw75-F60405
Q3#6-32 Nut/Washer Assembly75-995 16
Q3Thermally Conductive Silicon Insulator78-16008
QsThermally Conductive Silicon Insulator78-16008
Q5, Q7#6 x %;Inch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc-72-6606S

Plated-Steel Screw

Heat Sink 034531-01 Test Point Acceptable substitute is part no. 020670-01 179051-001

3-32

Page 55

Millipede™ Maintenance, Repair, and Parts

H. Power Supply Assembly

WARNING

Fuse cover must be in place during game operation. A035888-01 (Transtormer assy)

A021084-xx (Voltage plugs) 29-053 (Capacitor) 034544-01 (Fuse block cover)

79-4411001 (Fuse post) 78-70501SC (Capacitor bracket) ' L, 46-2017002 (Fuse)

7 orennee 034482.02 (Fuse harness assy.) (Chassis)

46-301203 (Fuse)

037639-01 (Label)

(Bushing)

‘A034630-01 79-3206 (Filter Assy.) (Fuse block) 037641-01 46-2014002 (Label) (Fuses)

79-15021001 ‘A035890-01 (Terminal block) \ (Power harness) A034629-01 3A-MDA3501 (AC harness) (Rectifier)

Figure 3-16 Power Supply Assembly A037671-01 & -02 E

3-33

Page 56

Maintenance, Repair, and Parts Millipede™

Power Supply Assembly Parts List

Assemblies and components in the following parts list are shown in Figure 3-16.

Part No. Description

A021084-01Voltage Plug for 100 V (90-110 VAC)(violet wire color—plugs into J3)
A021084-02Voltage Plug for 120 V (105-135 VAC)(yellow wire color—plugs into J3)*
A021084-04Voltage Plug for 220 V (200-240 VAC)(blue wire color—plugs into J3)
A021084-05Voltage Plug for 240 V (220-260 VAC)(brown wire color—plugs into J3'

A034629-01 AC Harness Assembly (J4A) A034630-01 RFI Filter Assembly (FL1i—designation not marked) A035888-01 Transformer Assembly (T1—designation covered) (Acceptable substitute is part no. A035888-02) A035890-01 Power Harness Assembly (J2) A035891-02 Fuse Harness Assembly (F2-F6) 29-053 27,000 uF, 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Type-MDA 3501 Bridge Rectifier (CR1)

46-20140024A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30120320 A, 32 V, 3AG Slow-Blow Glass Cartridge-TypeFuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x %-Inch Outside Diameter x %4-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket (C1)

79-150210012-Circuit Single-Row Terminal Block(/ocated under F4)

79-3206 5-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals (F2-F6) 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post (F1) 034482-02 Power Supply Chassis Base 034544-01 Fuse Block Cover (F2-F6) 037243-01 Metal Base Plate (not shown in illustration) 037639-01 Label for Fuse Value (F1) 037641-01 Label for Fuse Values (F2-F6)

*This is the only plug provided on the North American power supply.

NOTE A037671-01 power supply assembly has the 120 V plug. A037671-02 has the 100 V, 220 V, and 240 V plugs. A037671-03 has the 220 V and 240 V plugs.

3-34

Page 57

YOUR COMMENTS, PLEASE! Mitipede™

ist printing

Your comments will assist Atari in improving our publications The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm OD Distributor

Address CD Operator

City Country O Other.

Phone City Code Country Code

Page 58

First fold

No Postage Necessary mailed in the United States

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086

Second fold

wol4 aBpe siyj adey

Page 59

YOUR COMMENTS, PLEASE! vou

1st printing

Your comments will assist Atari in improving our publications. The comments are an important pari of preparing for revisions of game manuais. Please write in the space below.

lf you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm Oi Distributor

Address O Operator City Country O Other

City Country O Other.

Phone City Code Country Code

Page 60

First fold

Atari ireland Limited Attn.: Field Service/Coin-Op Division

Tipperary Town, Ireland

Attach Necessary Postage

Second fold

ebpe siyj edey Wwol4

Page 61

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

Seller warrants that its printed-circuit boards and parts thereon are {ree from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are

returned to Seller during said warranty period, provided

  • Seller is promptly notified in writing upon discovery by Buyer that said products are detective:

(b) Such products are returned prepaid to Sellers’ plant, and

  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, negiect, alteration, improper repair, installation or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety. Alari distributors are independent, i bal el baedlegiadnn cite In their judgment they may sell parts or accessories other than or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor. This document is and contains confidential trade secret information of Atari, Inc. This document is loaned under contidential custody for the sole purpose of operation, Imantnarc cr epi oa ara anda te sy sd ayers any other purpose whatever, and remains the property of Atari, Inc. Neither it nor the information it contains may be reproduced, used, or disclosed to persons not hav- ‘jing a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 64

A.

ATARI

ATARI, INC. 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488