CATHODE RAY TOMES

Vampire Savior

Vampire Savior: The Lord of Vampire (Europe 970519) (Capcom, 1997) · Manual · 14 pages · 18 sections · original scan

Page 1

©CAPCOM CO., LTD. 1997 ALL RIGHTS RESERVED ©CAPCOM U.S.A., INC. 1997 ALL RIGHTS RESERVED

OPERATORS MANUAL

/\\. WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

CARCOMY COIN-OP, INC. 475 Oakmead Parkway Sunnyvale, CA 94086 Phone: (408) 774-0500 Fax: (408) 522-5331

PM00200 060497

Page 2

® CAPCOM" coin-op, inc. VAMPIRE SAVIOR ™

THANK YOU FOR PURCHASING VAMPIRE SAVIOR™ WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: CUSTOMER SERVICE 475 OAKMEAD PARKWAY SUNNYVALE, CA 94086 PHONE: (408) 522-5325 FAX: (408) 522-5331

THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

"B" CARTRIDGE AAMA SERIAL NUMBER <>< SERIAL NUMBER

"A" CARTRIDGE SERIAL NUMBER (BOTTOM OF CASE) 300900

DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE:

“FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA SERIAL #

“B” KIT B-CARTRIDGE SERIAL # AAMA SERIAL #

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 3

CAPCOM’ coin-op, inc. VAMPIRE SAVIOR ™

KIT INSPECTION

There are two kits available for conversion to VAMPIRE SAVIOR™:

  • VPS1000 (“FULL” kit) contains the 2) VPS1000B (“B” kit) contains the game complete game cartridges, all necessary graphics, software cartridge (B-cartridge) and must also be and replacement joysticks and button switches. The installed to a current CAPCOM® System II game. “FULL” kit is intended for conversion of most It includes all the necessary game graphics for a JAMMA-compatible, horizontal screen cabinets. cabinet conversion (marquee, control panel overlay, monitor card, etc.).

Check that all parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

KIT PARTS LIST vpsi000 | vPs1000B | PART NO. DESCRIPTION [a __|_ | WPS1400____ | CPST System Cartridges (AB) [1

prvPsi4008| CPS Tr System Cariidge (B)|1

pv JE 1200 [MonitorCard——SSSC~dSCC rAW00247 [Marquee ___——S—S FAWOOI4S-1 | Overlay, Control Panel____—~dt——it id

FAWO00248| Decal, Joystick & Button Switches| ___1

TAWOOI47 | Decal, Cabinet Side ——=—=—S~dCSCi* rAW00249 | Decal- Top, Insiruction __—~+(|—1—* -AW00250 | Deeal- Botiom,, Instruction | _1__| PM00200 |Manual, Operators __———S~S~idSSC

GE2030| oystick,way _——S~dSCi

: a rae a pa a i e

13-0066| Bracket, A-Cariidge Mounting|4
[16-0130| Switch, I-Player Start Bution (White)| __1

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 1

Page 4

® @NP@OM" coin-op, Inc. VAMPIRE SAVIOR ™

CAUTION

Please read the following instructions to keep the PC board in good condition:

¢Do not block the ventilation slots.

¢Do not drop or bump the board.

¢Do not spill any liquids on the case.

Do not disassemble the case.

ATTENTION

The product that you have purchased contains a recyclable battery. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste system. Check with your local solid waste official for details in your area for recycling options or proper disposal.

DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY

OF YOUR REPAIR WARRANTY.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 5

CAP@OMI° coin-op, INC.

KIT INSTALLATION

WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

  • Disconnect and remove the old printed circuit board(s) from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the drill hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel cover, figure 1 (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *cover is not included in the kit.
  • Plug up unused holes with a wood dowel (1-1/8" diameter) and sand any rough edges.

INSTALLATION

Marquee Installation

  • Remove the marquee plexi glass, marquee overlay, and the cabinet graphics.
  • Install the new marquee and replace the plexi glass. Clear plexi glass is included in “full” kit.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keepihg it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay. VAMPIRE SAVIOR ™
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel cover, figure.1. (if required).

Overlay (Trim to size)

Control Pane!

Figure 1: Overlay Installation

CABINET DECAL INSTALLATION

  • Remove monitor glass and install monitor card
  • Peel-off the backing to the instruction decals and place on both the top and bottom of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.

MARQUEE OVERLAY MONITOR CARD

INSTRUCTION DECAL - BOTTOM

|] INSTRUCTION DECAL - TOP

wen

Figure 5: Cabinet Decal Installation

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 3

Page 6

CAP@@NT’ coin-op, Inc.

ONE button on the top left-hand side of the control panel, and the player two button on the top right-side of the control panel. ro @ ey" 2)

Figure 2: Start Buttons Red Green Blue Red Green Blue

Red Green Blue Red Green Blue

Buttons

Retaining Rings ia Switches —— us, 4g Figure 3: Control Panel Buttons and Switches

  • Install all buttons and retaining rings on the control panel as shown in Figure 3. Install two red buttons to the immediate right of each joystick, install two green buttons to the right of the red ones, and install two blue buttons to the right of the green ones.
  • Install the switches on the buttons as shown in figure 3. Orient the switches so that when a button is pressed, the plastic contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in figure 4.

Figure 4: Joystick Installation

CONTROL PANEL WIRING VAMPIRE SAVIOR ™

NOTE: all switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch.
  • Reconnect the existing jamma connectors to the control panel according to the chart in table 1.
  • Connect the player | and the player 2 kick buttons to the auxiliary cable harness as shown in figure 6. Make the connections according to the chart in table 2.

To A-Cantridge

To Volume / Test Switch Bracket vray Figure 6: Auxiliary Cable Harness

TEST SWITCH WIRING

  • Your cabinet may already equipped test switch. An optional test/volume bracket (see Figure 7) is available through your local CAPCOM distributor (part number 03- 0050). When installing, the test switch bracket should be mounted inside the coin door and on top of the cash box for easy access. (See Page 7 for wiring detail)
NOTE: only the test switch is used for this game; the volume up/down switches are disabled. Volume adjustments must be made through the volume control knob located on the PC board.

Figure 7: Test/Volume Bracket

  • Ifyou are converting a cabinet that is equipped with CAPCOM® Q-SOUND, you may use stereo audio output connect to existing Q-SOUND POWER AMPLIFIER.

4 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 7

CAPCOM coin-op, Inc.

AY CAUTION

IMPROPER INSTALLATION OF THE JAMMA HARNESS TO THE GAME CARTRIDGE WILL CAUSE DAMAGE TO THE ENCLOSED PCB. VAMPIRE SAVIOR ™

WARNING

DISASSEMBLY OF EITHER GAME CARTRIDGE WILL VOID YOUR WARRANTY.

GAME CARTRIDGE INSTALLATION

“FULL” KIT

  • Install the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 10.

oO

Figure 10: Mounting Bracket Installation

“FULL” KIT 21, Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 11.

voor Figure 11: Case Mounting

  • Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q-SOUND, also attach the audio cables. “B” KIT
  • To remove the existing “B” cartridge from the “A” cartridge, pull the old case clamps apart (see Figure 12). Carefully remove the old “B” cartridge and install the new “B’ cartridge. Re-install the case clamps.

"B" Cartridge

"A" Cartridge Figure 12 : Case Clamp Installation

  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 5

Page 8

CAP@EM" coin-op, INC. VAMPIRE SAVIOR ™

TEST MENU The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin door or switches, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

PLAYER I SHOT I button, as shown below in various control panel configurations: TES MENU 1. ACCESSING THE TEST MENU ° For a CAPCOM® cabinet, or a cabinet with

tINPUTa test switch:
2.OUTPUTMake sure the game is on and push the test switch.

The screen shown left will appear.

KSOUND & VOICE°For a cabinet without a test switch:
4.COLORPush the blue test switch on the outside of the black

plastic casing.

5.DOT CROSS HATCHRefer to the inside back cover of the manual.
  • GAME DATA
  • HOW TO SELECT AN ITEM
7.CONFIGURATION.Use the PLAYER | JOYSTICK to move the
8.MEMORY CHECKarrow in front of the desired item and press the

9. EXIT

SELECT = 1P UP or DOWN

START =1P SHOT13.CLOSING THE TEST MENU

To close the Test Menu, highlight “9. EXIT” and push the PLAYER J SHOT I button. Player 1 Joystick Player 1 Start . To return to the test menu, push the PLAYER 1 START and PLAYER I SHOT | buttons simultaneously. . The test menu will always return to the screen:

  • After you exit the “7, CONFIGURATION MENU” and Player 1 Shot 1 Player 1 Shot 2 vieor b) After the memory is tested from the menu, “8. (Punch Light) (Punch Middle) MEMORY CHECK”.

a. TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved. OUTPUT SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER / JOYSTICK. Push the PLAYER

COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background. DOT CROSS HATCH Used to test the screen size, focus and distortion. GAME DATA Coin meter and Free play information will be displayed. CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section. MEMORY CHECK Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears. EXIT Select this item and push the PLAYER J SHOT / button to return to game play mode.

6 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 9

CAPCOM coin-op, Inc. VAMPIRE SAVIOR ™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

  • ACCESSING THE CONFIGURATION MENU
  • CONFIGURATION MENU ¢ From the TEST MENU, move the arrow to “7, CONFIGURATION?” and push the > 1. SYSTEM PLAYER 1 SHOT | button. The screen left will be displayed.
  • GAME A description of each option is explained in the table below.
  • DEFAULT
  • SAVE & EXIT

SELECT 1P UP OR DOWN START 41P SHOT1

  • CONFIGURATION MENU ITEM DESCRIPTIONS

SYSTEM | Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER 1 SHOT I and PLAYER I SHOT 2 buttons at the same time to restore default values. SAVE & Use this to save new configuration settings and exit to the Test Menu. The message “SAVING NEW EXIT CONFIGURATION IN EE-PROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. q

Page 10

CAPCOM’ coin-op, inc. VAMPIRE SAVIOR ™

SYSTEM CONFIGURATION

CHANGING THE SYSTEM 7-1. SYSTEM CONFIGURATION CONFIGURATION SEETINGS

. COIN MODE2 COIN 1 CREDITMove the PLAYER I JOYSTICK up or down to highlight

the desired option. Once the option is highlighted, move

« CONTINUEONthe PLAYER I JOYSTICK left or right or press the
. MONITORNORMALPLAYER I SHOT I button to select.

. DEMO SOUND ON

. SOUND MODE STEREO (QSOUND)

. CHUTE TYPE 2 CHUTES SINGLE

. REGULATION ON

  • EXIT

SELECT OPTION =1P UP OR DOWN MODIFY SETTING = 1P LEFT OR RIGHT = 1P SHOT1 OR SHOT2

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

SELECT THE CHARGE PER PLAY. SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY.

  • MONITOR FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL. TURNS ATTRACT SOUNDS ON OR OFF.
  • SOUND MODE | SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET.
NOTE: STEREO SHOULD ONLY BE SELECTED FOR USE WITH CAPCOM® QSOUND CABINETS. SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTE TYPE. If set to “ON” the color of the blood changes from red to white. TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH EITHER THE PLAYER I SHOT 1 BUTTON OR THE PLAYER I SHOT 2 BUTTON.

SYSTEM CONFIGURATION OPTION SETTINGS

1. COIN MODE1 COIN1 COIN1 COIN1 COIN1 COIN
1 CREDIT2 CREDITS3 CREDITS4 CREDITS5 CREDITS
1 COIN1 COIN1 COIN1 COIN2 COINS
6 CREDITS7 CREDITS8 CREDITS9 CREDITS1 CREDIT
3 COINS4 COINS5 COINS6 COINS7 COINS
| CREDIT| CREDIT1 CREDIT1 CREDIT1 CREDIT

8 COINS 9 COINS 2 COINS START FREE PLAY 1 CREDIT 1 CREDIT 1 COIN CONTINUE

  • CONTINUE ON
  • MONITOR NORMAL

STEREO (Q SOUND)

On

NOTE: FACTORY SETTING

8 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 11

® CAPCOM" coin-op, INC. VAMPIRE SAVIOR ™

GAME CONFIGURATION

CHANGING THE GAME CONFIGURATION 7-2. GAME CONFIGURATION SETTINGS

set vhaues aes NORMA Move the PLAYER I JOYSTICK up or down to highlight

  • DAMAGE LEVEL NORMAL the desired option. Once the option is highlighted, move . GAME SPEED NORMAL the PLAYER I JOYSTICK left or right or press the

. LIVES 2 LIVES

. EVENT OFF

  • AUTOMATIC OFF
  • EXIT

SELECT OPTION =1P UP OR DOWN MODIFY SETTINGS =1P LEFT OR RIGHT 1P SHOT1 OR SHOTQ

ITEM DESCRIPTION OPTION SETTINGS

  • DIFFICULTY | SETS THE GAME DIFFICULTY LEVEL NORMAL
HARD 3* HARD 4HARD $EXPERT
2. DAMAGESETS THE NUMBER OF COUNTER GEMS. THE HIGHERLOWNORMALHIGHMAXIMUM

LEVEL THE LEVEL, THE MORE COUNTER GEMS APPEAR ON THE OPPONENT’S FIELD.

3. TIMERSETS THE SPEED AT WHICH THE COUNTER GEMSSLOWNORMALFASTFASTEST

SPEED DROP.

4. GAMESET THE GAME SPEED.SLOWNORMALFASTFASTEST

SPEED

5. LIVESSET NUMBER OF LIVES.1 LIFE2 LIVES3 LIVES4 LIVES

; ON OFF EVENT SPECIAL SETTING FOR TOURNAMENT EVENT. | MATCH: ONLY ONE CREDIT IS REQUIRED FOR A 2P GAME. THE GAME ENDS AFTER ONE MATCH REGARDLESS OF THE RESULT.. AUTOMATIC | USED TO TURN THE “AUTOMATIC MODE” ON AND FREE SELECT OFF. SET TO “FREE SELECT” ALLOWS THE PLAYER TO SELECT NORMAL OR AUTOMATIC MODE.

  • EXIT RETURN TO THE CONFIGURATION MENU.

e Recommended “Difficulty Level” setting for Arcade. e If you purchase “B” Kit , you may need adjust “Difficulty Level” setting. Nese §=6FACTORY SETTING

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 9

Page 12

CAP@@M1’ coin-op, INC. VAMPIRE SAVIOR ™

JAMMA Connections

SOLDER SIDE COMPONENT SIDE

WIRE COLOR CONNECTOR ODD ROW CONNECTOR EVEN ROW WIRE COLOR

ee a a

rCNSC“CSCSCSCS NG a NG NC NC NG NG NC PCN CSCSCSC~*S NC CN NC rNe Cid

PLAYER I KICK-COMMON

& Weite ite os as Coe Oo n

GC) =

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 13

® CAPCOM” coin-op, INC. VAMPIRE SAVIOR™

REFERENCE INFORMATION

GAME CASE CONTROLS

COIN REGISTER

METER (NOT USED) COMMUNICATION (NOT USED) PORTS (NOT USED)

TEST

“VOLUME UP

*VOLUME DOWN

JAMMA AUXILIARY CABLE AUDIO OUT (FOR Q SOUND) CONNECTOR CONNECTOR RIGHT: RED, LEFT: WHITE V300800

TYPICAL CONTROL PANEL LAYOUTS FOR “VAMPIRE SAVIOR™”

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 14

NOTICE

This equipment has been tested and found to cemply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Gperation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federa! law provides severe civil and E criminal penalties for the unauthorized reproduction, distribution, or exhibition g of copyrighted audiovisual works and f video games.

The Federal Bureau. of Investigation # investigeies allegations of criminal copyright iniringement.

CARCOMtetES INC. 475 Oakmead Parkway Sunnyvale, CA 94086 Phone: (408) 774-0500 Fax: (408) 522-5331

Copyright © 1997 CAPCOM ® coin-op, INC., All Rights Reserved