CATHODE RAY TOMES

Three Stoogers Operating Manual

The Three Stooges (Mylstar, 1984) · Operating Manual · 39 pages · 28 sections · original scan

Page 1

He rYyyyyyy) 1

© COPYRIGHT 1984 NORMAN MAURER PRODUCTIONS, INC./COLUMBIA PICTURES INDUSTRIES, INC.

a INSTRUCTION ive MANUAL

Page 2

FORM ADDENDUM

ATTACHED TO AND PART OF THE THREE STOOGES (GAME GV-113) INSTRUCTION MANUAL

GAME AS SHIPPED VARIES FROM THE INSTRUCTION MANUAL AS PRINTED

Add the following to VIII. GENERAL INFORMATION--C. FUSES-~BOTTOM PANEL on page 9 of the instruction manual:

F12 INPUT LINE FUSE 8 Amp SLO-BLO PART NO. EL-26

Make the following changes as shown in the figure below, in the partial illustration of the PRIMARY POWER/FILTER BOARDS/INTER- CONNECTION DIAGRAM schematic on pages 30, 31 and 32 in the instruction manual:

  • Add fuse F12 to the POWER INPUT LINE as shown in the figure below.
  • Change wire color 700, between POWER LINE INPUT and F12 to 766, add wire color 700 from the F12 Fuse (Output Side), to the junction of the 0 wire which is part of SW1 and wire 700 which goes to A12J2-1

sw2 FRONT INTERLOCK coo

tor [733]

50H7/60Hz

NO. TMS 5/29/84 24141

Page 3

SEC.

I

ih

Wh

Iv.

Vi.

Vil.

Vill.

IX.

Xi.

“WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may Cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may THE THREE STOOGES (GAME GV- 113} INSTRUCTION MANUAL

TABLE OF CONTENTS

PAGE

INSTALLATION ......0000.. eee 2

INITIALIZATION ...... 0.0... 3

GAME OPERATION...............................5 3

GAME PLAY AND SCORING .................... 4

SOUND/SPEECH ... 6

GAME ADJUSTMENTS/OPTIONS ................ 6

BOOKKEEPING AND SELF TEST ................. 7

GENERAL INFORMATION .. 9

THEORY OF OPERATION ......................... 1

WIRING AND SCHEMATIC DIAGRAMS .......... 12

PARTS INFORMATION .......... 2.200000... 33

WELLS GARDNER MONITOR, SERVICE AND OPERATION MANUAL (Attached)

be required to correct the interference.”

WARRANTY INFORMATION IS LOCATED ON THE INSIDE BACK COVE!

OR SERVICE, CALL TOLL FREE: 1-800-323-9121; (ILLINOIS) 1-800-942-1 NOTICE

Page 4

I. INSTALLATION

THe

© COPYRIGHT 1984 NORMAN MAURER PRODUCTIONS, INC./COLUMBIA PICTURES INDUSTRIES, INC.

A. SET-UP

  • Carefully inspect the exterior of the game for any damage which might have occurred during shipment.
  • Unlock and open the rear cabinet door.
  • Check that all plug in connectors are seated firmly. The connectors are keyed so they will only go in one way.
  • Remove the binding strap from the line cord, and install the line cord plate in the groove provided.
  • Cabinet levelers (2) are stored within the cash box for shipping purposes. Install and adjust as necessary.

B. CHECK-OUT

  • Check that all cables are free of moving parts.
  • Check for any loose wires.
  • Check for loose solder or foreign matter on switches and power supply assemblies.
  • Be certain all fuses are seated firmly.
  • Be sure transformer wiring corresponds to the supply voltage.
  • Refer to section VI to make all the necessary game adjustments.

Reassemble the game.

  • Plug the line cord into a properly grounded 3-wire receptacle ONLY! c CONTROL PANEL REMOVAL
  • Unplug the game.
  • Unlock and open the coin chute door.
  • Reach in through the coin chute door and remove the wing nut and flat washer from each of the two carriage bolts which secure the control panel to the game. Unlatch the control panel latch at the top center of the panel. Note where the latch strike plate is located. Remove the carriage bolts.
  • Pull the control panel back, grasp it at the front edge as far back as it will go (approximately 4”)
  • Raise the front of the control panel approximately one inch above its supports and lift the entire assembly high enough to disconnect A9J1/A9P1 and A9J2/A9P2.
  • Remove the entire contro! panel assembly from the game.
  • The joystick’s and leaf-switches are now accessible for removal or cleaning.
  • For reassembly, reverse the above procedure.

MONITOR REMOVAL 1, Unplug the game.

  • Perform the control panel assembly removal procedure (Section C).
  • Unlock and open the rear cabinet door.
  • NOTE: The color monitor contains HIGH VOLTAGES delivering LETHAL quantities of energy. Do not attempt to service the
Page 5

L INSTALLATION, II. INITIALIZATION, Ill. GAME OPERATION

E. 8.

I. INSTALLATION

monitor until you have shorted the anode plug on the picture tube to ground. Disconnect the video plug AI7J1, the monitor power supply plug Al2J3/A12P3 and the ground wire from the monitor chassis. . From the rear of the game, remove the one nut and one washer from each of the four carriage bolts used to secure the monitor to the platform Remove the monitor from the rear of the game, being careful to clear all cables from the CRT neck. For reassembly, reverse the above procedure.

SPEAKER ASSEMBLY AND MARQUEE REMOVAL 1.

2.

3.

4. Unplug the game. Unlock and open the back door.

Unplug the A15-J1/P1 connector. Unlatch the two latches on the rear of the Speaker Assembly Panel located inside the back door above the monitor.

. On the front of the game, pull down on the lower molding under the marquee. The Speaker Assembly will lower to allow removal of the marquee.

  • Remove the marquee by lifting it upward out of its track. The Speaker, Assembly and lilumination Assembly are now accessible for servicing.
  • Tilt the front of the Speaker Assembly downward while lifting the center upward.

Pull the assembly straight out to remove. Be careful not to pinch the Speaker Assembly cable.

  • For reassembly, reverse the above procedure. When replacing the marquee: a. Tilt the front of the Speaker Assembly downward. b. Place the bottom of the marquee in the lower molding track on the front of the assembly. c. Apply slight pressure with your thumbs to the lower left and right corners of the marquee. d. Slowly raise the Speaker Assembly until the top of the marquee is in place in the upper track in the top molding. e. Be certain to reconnect the AI5-JI/P1 connector and relatch the rear assembly latches.

Il. INITIALIZATION TURN GAME ON Immediately, the coin chute lamps and the speaker marquee lamp will turn on.

AFTER A TEN SECOND DELAY A The attract mode appears on the screen. B. The playing field cycles through the following

  • High Game to Date screen
  • Instruction Set
  • Game Play Cycle

ll. GAME OPERATION

A. GAME START 1. Insert coins into coin chute. a. Coin chute tune is played. b. Total credits are displayed on screen. Press one (Larry), two (Moe) or three (Curly) player button to start game. a. Total credits are decreased by one, two or three. b. Choose Larry, Moe or Curly by moving the respective joystick. ce. Game initializes.

Page 6

lll. GAME OPERATION, IV. GAME PLAY AND SCORING

B, ONE PLAYER

  • The player's selected Stooge picture and name is displayed at top of screen.

C. ADDITIONAL PLAYERS

  • Additional players are indicated by their selected Stooge picture and name at top of screen.

D. EXTRA STOOGES

  • Each player will begin with three Stooges (dependent on option/parameter settings).
  • Extra Stooges are earned by achieving certain score levels (dependent on option/ parameter settings).

E. GAME OVER

  • When each player loses his last Stooge, his name with the words Game Over will transfer to the bottom of the screen.

IV. GAME PLAY AND SCORING

HOW TO PLAY

The object of the "Three Stooges" game is to rescue the three brides, Cora, Nora and Dora from the evil Doctor, I.M.Acad M.D.

One, two or three players can choose their favorite Stooge and play either as a team, or against one another. In a one player game the game is played against the computer.

"Three Stooges" consists of seven scenes: (1) The Office; (2) The Parlor; (3) The Kitchen; (4) The Singers; (5) The Art Gallery; (6) The Police Station; and (7) The Laboratory. The players must pick up their respectively colored key in each of the seven scenes, and exit the room. Each scene is repeated in all four levels of difficulty.

The game play starts with all three Stooges in the midst of the first scene, the "Office". With the help of the player controlled joystick, the player searches for a hammer. With the hammer the player can either break furniture to find the keys, or hit the cops and villians which are worth points. The player can also pick up pies, which are located on unbreakable tables and throw them

Page 7

IV. GAME PLAY AND SCORING

at unsuspecting cops and villians. The player must be careful though, because a pie thrown haphazardly will break windows along the sidewalls encouraging more cops to enter the room.Picking up a pie will also cause the player to lose the hammer.If a player chooses to slap a villian by pressing the slap/throw button on the control panel, the villian will be stunned and if a hammer was being carried, it will be dropped.

Each scene is completed when all three keys are retrieved and the Three Stooges exit the room. All three keys must be picked up to open the exit door.

The players must be very careful during the "Singer" scene.The key for each of the players is located in one of the smaller rooms. When entering the room the Player must be quick about retrieving the key because the opera singers “blue note" is lethal.The singers can be silenced by hitting them in the face with a pie.

During the first level of the "Laboratory" scene, there are no brides present. The evil Doctor, I.M.Acad M.D., stands atop the laboratory and as the players pick up their keys the Doctor starts leaving the room. The players must exit capture the Doctor or begins over again. in time to the round The first of the three brides, Cora, appears at the start of the second level The players must retrieve the keys to change the color of the cage in which Cora is locked. The cage must then be broken with a hammer, Cora rescued, and exit the room.

Nora, the second bride appears during the third "Laboratory" round and Dora, the third bride, appears during the fourth "Laboratory" round.

When Dora has been saved, this will complete the first four levels of the game. The game now repeats the order of the first four levels, with the evil Doctor coming out again in the “Laboratory" scene of level five.

BREAKING WINDOW = 100 POINTS

VILLIANS a. Muffy = 200 POINTS b. Beauregard = 200 POINTS

COPS (Flatfoot) = 500 POINTS

LOOT a. Key = 500 POINTS b. Oscar = 500 POINTS c. Star = 500 POINTS d. Money bag = 500 POINTS

SCIENTIST = 500 POINTS

THREE STOOGES a. Larry = 500 POINTS b. Moe = 500 POINTS c. Curly = 500 POINTS “Laboratory" game.

Page 8

V. SOUND/SPEECH, VI. GAME ADJUSTMENTS /OPTIONS

V. SOUND/SPEECH

SPEECH

"Hello"

"Oh a wise guy, huh"

"Cheese it boys, it's the cops"

"ow"

"Spread Out"

"What's the matter, knucklehead"

"AAAHHH"

"Hey, watch out"

"YAK, YAK, YAK"

"NAYAUGH, NAYAUGH, NAYAUGH"

"Oh, look at the grouse" OCCURENCE

Moe, Larry or Curly when chosen as a player.

Moe, Larry or Curly when contacted.

Moe, when cops enter room.

Moe, when hit with hammer or slapped.

Moe, when contacted.

Moe, when contacted.

Larry, when contacted.

Larry, when contacted.

Curly, when contacted.

Curly, when contacted.

Curly, during break screen (4thievel).

VI. GAME ADJUSTMENTS /OPTIONS

A. CONTROL BOARD SWITCH ADJUSTMENTS SWITCH 1 _. LIVES PER GAME OFF . sete eee esses 3 LIVES ON . ++. 5 LIVES

SWITCH 2. ___ ATTRACT PLAY OFF... eer SOUND ON .. . «INQ SOUND

SWITCHES

. FREE PLAY

NOT USED.

DIFFICULTY CONTROL NORMAL -. HARD.

EXTRA LIVES FIRST EXTRA EACH ADDITIONAL UFE UFE ON ON . 10,000 POINTS EVERY 10,000 POINTS ON OFF 0,000 POINTS EVERY 20,000 POINTS OFF ON 100 POINTS EVERY 10,000 POINTS OFF OFF | 100 POINTS EVERY20,000 POINTS B. SOUND ADJUSTMENTS The audio output is controlled by the potentiometer mounted on the service panel assembly (located inside the coin mechanism door).

Turning the potentiometer counter-clockwise will decrease the volume. Turning it clockwise will increase the volume.

Cc. MONITOR ADJUSTMENTS Normally, few if any adjustments are required for proper monitor operation. However, after any major repairs to the monitor chassis refer to the attached monitor manual.

Page 9

Vil. BOOKKEEPING AND SELF TEST

SELF TEST

The battery back-up bookkeeping functions of this game are contained in Self Test steps 3 and 4. These are in addition to the electro-mechanical coin counter located inside the front door panel. Every time a coin is inserted into a coin slot, the counter is energized, incrementing the count.

The self-test consists of six functions which may be used to identify problems in the video system and to change program parameters.

The self-test mode is entered by setting the self-test toggle switch located inside the cash door to “TEST”. A selection of available tests is displayed on the monitor. To return to the GAME mode at any time, the operator needs only to set the toggle switch back to “GAME”.

Selection of tests is done with the push button switch labled “SELECT”. Upon entering the test mode, a flashing arrow points to the first test selection. Momentarily depressing the “SELECT” button will advance through each selection one by one When the arrow is pointing to the desired test, the operator may begin that test by pressing the “SELECT” button and holding it down until the test appears on the screen.

Once a test has been selected, the operator can return to the selection fist by holding down the select switch until it re-appears. The six tests are as follows:

  • MONITOR ADJUSTMENT Four patterns can be displayed on the screen for adjusting monitor color, brightness, contrast and convergence. The patterns are: Color bars, a cross-hatch, a gray scale, and a dot pattern. By momentarily pressing the select switch, the operator may cycle through the four patterns.
  • MEMORY TEST

For each RAM memory chip: An OK or an NG (no good) appears signaling that the chip is good or bad respectively. Check sums are displayed for each ROM memory chip. If you have a suspect ROM, refer to your distributor for the correct check sum number.

  • SOUND/SPEECH TEST

After selecting this test, a count will appear on the screen, representing the various sounds that are produced by the game. All the different game sounds will be produced and the screen count will repeat to 01. Pressing the MOE button will suppress all sound output and speed up the count so a particular sound can be sought out and checked.

  • BOOKKEEPING Selecting this test will display a menu of four functions. Pushing the SELECT button momentarily will move an arrow on the screen. When the arrow points to the desired function, press the MOE button on the control panel to perform that function. DISPLAY SCORE COUNTS — A table is shown with 20 categories of score values by thousands (K} and a count associated with each category. The count represents the number of plays in which the score at the end of the game fell into that category. In addition, a high score, low score, and average is shown along with the total number of plays on which the average is based. To clear the table, press the MOE button and return to the menu by holding down SELECT.

DISPLAY TIME COUNTS — Same as above except each category represents play times in seconds. The high, low, and average are given in minutes and seconds.

DISPLAY ROUND COUNTS — Same as above except each category represents the round in which the games ended.

Note: Each of these tables are independent of the others. Any table may be cleared without affecting the others in any way.

RESET HIGH SCORE - Pressing the MOE button will reset the Top Bananas table (all-time high scores).

Page 10

Vil. BOOKKEEPING AND SELF TEST

DIP SWITCHES A functional description of the eight Dip Switches located on the Logic Board Assy. is displayed. Changing any switch will cause an immediate update of the description displayed on the screen.

  • SWITCH TEST Pressing any player button, coin switch or moving the joysticks in any direction will display an OK for each switch closure.
Page 11

Vill. GENERAL INFORMATION

A. PRINTED CIRCUIT BOARDS ARE DESIGNATED AS FOLLOWS:

Al Logic Board Assy.

A3 Power Supply Assy.

A6 Sound Board Assy.

A7 Diode Board

A8 Filter Board

B. WIRE COLORS ARE SHOWN AS NUMBERS:

7 Purple some | cer |

For example, 688 is a Blue - Gray - Gray striped wire.

Cc. FUSES

BOTTOM PANEL

Fl115V AC 60 Hz (Primary Power)3 Amp SLO-BLO
F26.3V AC (Coin Chute Lamps)1 Amp SLO-BLO

F3 Monitor 2 Amp SLO-BLO

Fa9V AC {+5V DC)12 Amp SLO-BLO
FS15V AC+12V DC2 Amp SLO-BLO

( -12V DC

F61SV AC+20V DC2 Amp SLO-BLO
F7Audio Amplifier Supply1.5 Amp SLO-BLO
FSOV AC (RESET)1/4 Amp SLO-BLO.
Page 12

Vill. GENERAL INFORMATION

POWER SUPPLY SPECIFICATIONS

Logic Board Assy. (Al) Voltage adjustable. 6 Amps over-

Sound Board.

Coin Meter voltage protection and fused for

over-current protection.

(A6) +12V DC 1.5 Amp fused for over-current -12V DC protection. The plus and minus 12 volt supplies use the LM340K-12 and LM320T-12 IC regulators respectively.

+20V DC Full wave rectified unfiltered

voltage, 1.5 Amp fused for overcurrent protection.

Coin Chute Lights 6.3V AC AC voltage, 1 amp fused for overcurrent protection.

Monitor and Marquee 100V AC or] Isolated, fused AC voltage. 115V Ac, 60HZ

WARNING: The Shield Top covering the Master Electronics Panel will have to be removed in order to make some adjustments to the printed circuit boards. This cover is used, in part, to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules. Failure to replace the Shield Top over the Master Electronics Panel when the game is in operation voids all warranties.
Page 13

oe |

oll

a

r IX. THEORY OF OPERATION

INTRODUCTION The character based graphics system designated GG-lll has two main subdivisions. The first subdivision is the Central Processor Unit (CPU) which has three partitions: a. Microprocessors b. Memory c Input and Output ports (I/O)

The Inte! 8088 microprocessor is used and 32K bytes of memory is reserved for programming space and has 5 input ports and 5 output ports. The second subdivision is the video state machine which generates and controls the video signal to the monitor. The state machine has three partitions: a. System Clock (CLK) b. Foreground generator (FGND) c Background generator (BGND)

The system clock is driven by a 20MHZ crystal, divided down for a SMHZ dot clock.

All inputs and outputs including the video control and general purpose I/O are memory-mapped, {i.e. everything within the system can be addressed in a single segment of 64K addresses as memory).

The video contro! unit is divided into an “objectoriented” foreground driver and “character-oriented” background driver. The screen resolution is 256 pixels horizontally, and 240 lines vertically for both foreground and background. The CPU communicates with the foreground driver and background driver by writing data into the designated memory areas in a certain format The foreground is designed to display moving objects on the screen with a minimum overhead to the processor. The game programs will only have to specify the vertical and horizontal position and the object select number to the foreground driver. The background video supplements the foreground with relatively static figures on the screen. The CPU specifies all the character positions on the screen with desired “character ” patterns.

A 5SMHZ system clock drives a 9 bit horizontal dot counter and an 8 bit vertical line counter. The horizontal counter counts from 0 to 255 during active scan line and 256 to 317 during horizontal blanking time. W/hen the horizontal counter reaches 317, the horizontal counter resets to 0. At the beginning of the horizontal blanking time (horizontal counter = 256} it increments the vertical counter. The vertical counter counts from 0 to 239 during active vertical scan time and 240 to 255 during vertical blanking time.

The battery backup system supports two battery RAMs that store all of the bookkeeping functions. The battery is maintained at a +3.6V reference by a trickle charge supplied on the logic board regulated by a current limiting resistor. If the AC power to the game is interrupted, the battery allows the RAM’‘s to store the data contained in the Distrubutors table and the Options/Parameters screen.

Page 14

X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS

TABLE OF CONTENTS

LOGIC BOARD ASSY. (A1} COMPONENT LOCATION AND PARTS LIST SCHEMATIC DIAGRAM (SHEET 1 OF 3) ..... .. 16 SCHEMATIC DIAGRAM (SHEET 2 OF 3) ... SCHEMATIC DIAGRAM (SHEET 3 OF 3)

POWER SUPPLY ASSY. (A3) COMPONENT LOCATION AND PARTS LIST SCHEMATIC DIAGRAM

SOUND BOARD ASSY. (A6) COMPONENT LOCATION AND PARTS LIST SCHEMATIC DIAGRAM

PRIMARY POWER/FILTER BOARD/ INTERCONNECTION DIAGRAM

Page 15

X. WIRING AND SCHEMATIC

LOGIC BOAF LOGIC BOARD ASSY. [A1}, PARTS LIST 0 +c MISCELLANEOUS ELECTRONIC COMPONENTS t_o °

REFERENCEDESCRIPTIONPART

ne. =

BattBattery 36VXO-458
c-cleCapacitor. 01 UF SOV AX CRXO-230be

+80%-20% .

2sCapacitor. 100 UF, 25V LAXXO-212—
C26Capacitor,01 UE SOV AX CRXO-230

+80%- 20% DS.

27Capacitor, 100 UF, 25V ELAX — XO-212b
31-34Capacitor, 01 UF, SOV AX CRXO-230

+80%- 20% ell cst Capacitor. 100 PF, i00V CMD 5% xO-198

C52Capacitor. 01 UF, JOOV CMD 5% XO-196D4
C53Capacitor, 10 UF. 25V AX TANT = XO-127e

10% ALL UNMARKED R62 CAPACITORS Ol UF. SOV AX CR +80%-20% = XO-229 AL POLARIZED & 05" UNMARKED .

CAPACITORS.10 UF. 25V AX TANT 10%xO-127,
D2Diode. 1N4454XO-275,
OFDiode, 1N4733AXO-274
BsBane INx30obs
alTransistor, MPS-U45XO-306
2-04Transistor, 26044xO-120
81-087Transistor, MPSA70XO-309
R1-RIGResistor, 470 OHM, 5% "A¥/XO-35F
R25Resistor. 1K OHM, 5% awXxO-5©Dr
R31Resistor, 10K OHM, 5% 3\W/xO
R32-R34Resistor, 1K OHM, 5% '4\W/XO-5=
R37, R38Resistor, 330 OHM, 5% "WWXO-34
R39Resistor, 130 OHM, 5% ‘wvxXO1728.
R40Resistor, 270 OHM, 5% “AWWxO-68.
REI, RAZResistor. 510 OHM, 5% %WxO-25
R63Resistor. 130 OHM, 5% “WWXO-172
a4, RASResistor. IK OHM, 5% “4XO-S
RSI RSResistor, 330 OHM, 5% AWxO-¥08
R53. R54, RSSResistor. 1K OHM. 5% '4\W/xO-5oo
R57. RSBResistor, 560 OHM, 5% WWXO-36
959-R61Resistor. 1K OHM, 5% "WwxO-S
R63, ROSResistor, IK OHM, 5% “4WxO-SDIO
R70Resistor, 1K OHM. 5% ‘4\/xO-5*
R73, R74Resistor. IK OHM, 5% “4xO-SRel
R76-RB0Resistor, 1K OHM, 5% ‘4\WxO-5
RatResistor, 820 OHM, 5% “WWxO-174
R82Resistor. 100 OHM, 5% %WxO-28col
R83, RO4Resistor, 15 OHM, 5% 1XO-171:
ROSResistor. 180 OHM, 5% “WWXO-24eSSe
RB6, RB7Resistor, 15 OHM, 5% “WWX17ReLe
R88Resistor, 180 OHM, 5% AWxO-24R7S¢7s__ Bie _Jbd$DI
R89, R90Resistor. 15 OHM, 5% "WWXO171RetCee7
RaResistor, 180 OHM, 5% "WyxO-24*lirgc>o¢SSIP 4Cl2-13
m2Resstor,OHM, 5% AWXOSRSSsCci
R93Resistor. 2K OHM, 5% !XO-4siP2ljpncn &ROM |
R94Resistor. IK OHM, 5% “4xO-5Ri2t+clePSPGSDs
ROS,Resistor, 470 OHM. 5% "4xO-35ieSa .1i
R96Resistor, 240 OHM, 5% “WWXO173>HH==
R97Resstor 2K OHM. 59% AYXO-14Riscis>egoO
RBResistor, IK OHM. 5% 4xO-5RIG}-tCI6R85
R99Resistor, 470 OHM, 5% “AWXO-35aR84
R100Resistor, 240 OHM, 5% AWXO-173R3ecCURe8-——>
Rio!Resistor. 2K OHM, 5% "AVXO14Roe 204-18R87-—>
R102Resistor. 1K OHM. 5% “AWxO-54ROM 3l
R103Resistor. 470 OHM, 5% WWxO-35=
R104Resistor, 240 OHM, 5% AWXO-173,c26$Aide.Pa T9

SIP 1, SIP 2, SIP4 — Resistor, Dip. 4.7K. 9 Pin xO-492

Es ue SIP 72Resistor, Dip. 1K. 9 PinxO-493i—

1P 7.

X-TAL 41Crystal, 15 MHZxO-482R40ROM 40Die
XTAL STCrystal 20 MHZXO-494N*.
Dip SwitcnxO-505+R25
20 Pin Dip SocketxO-491—

22 Pin Dip Socket XO-467 BATTERY

24 Pin Dip SocketXO-529DI7
28 Pin Dip SocketXO-536_.
40 Pin Dip SocketXO-530oo
Page 16

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 17

oe ee ee ee i ee ee ee i ie Mii |

ma |

=s

“ty “WW TA REFERENCE

Al Az a3 AB, AS, AIO

B3 a4 Bs

BB 89, B10 Bil, B12, B14

cs rea C7. C8-9 9-10 cuz C1243 13-14 4s far o1 D2, D3, D4, DS, D6, D7, DB, D9, DIO pn DIZ D3 O15,

O16 o17

E1-2, E2-3, €4 ES & &7 EB, E9-10 10-11 eM-12

EIS

E16 €17 FS Fe a Fe

Ay

Gl. G2, G3. AGS rors LOGIC BOARD ASSY. [A1},

PARTS LIST (CONT.)

INTEGRATED CIRCUITS

DESCRIPTIONPARTREFERENCE

NO. Logic Board Assy. MAG = G7

8284 CLK Driverxo478GB

741802 Quad 2-input "NOR" gate xO-428 G9

74161 Synchronous 4-bit counterXO-192GIO
7418377 Octal "D” Fp FlopxO-97Gu

8088 CPU XO490 — GI2

741S373 Octal D-type flip flop-« XO-445G3, Gi, GIS
7418367 Hex 3-state bufferXO-444—Gl6, GI7

741808 Quad 2-input “AND” gate XO-86 HI, H2, H3, H4

74HC138 Decoder/demultiplexerXO-190HS. H6,

74LS139 Dual | of 4 decoder xO-4I9

748138 | of B decoderXO-13H7. H8, H9, HIO
7415138 1 of 8 decoderxXO437HI
7418240 Octal Buffer/ine driverXO-91HI2

7415373 Octal D-type flip flop. -s« XO-445— HI.

7415245 Octal Bus transceiverXO-79Hi4

RAM @ 6I16LP-4 xO-191

RAM 1 6I6LP-4XO191HIS

2128-4, 2Kx8 Static RAM XO-195 ——-HI6, HI7 ROM B 2732A 4K x8 EPROM — XO-485

ROM2764 8K x 8 EPROMxO489JI, J2, J3,
ROM 1 2764 8K x 8 EPROMx0489KIS, Jo
ROM 2 2764 8K x 8 EPROMxo489J?
ROM 3 2764 8K x 8 EPROMxo4s98
ROM 4 2764 8K x 8 EPROMxo4s99
7418139 Dual 1 of 4 DecoderxXO-419es a

J

74157 Quad 2-input multiplexerXO-1i44
74(S374 Octal D-type flip flopxXO-%Js
741244 Octal buffer/line diverXO-11716, JIT

74LS157 Quad 2-nput muttpiexer XO-390 74LS86 Quad 2-input exclusive — XO-435 KI, K2, KB. OR” gate ka

7418283 4-bit binary full adderXO-95KS
745161 Synchronous presettableXO-488.K6

binary counter K7-8

93419 64 x 9 bipolar RAMXO-999. KIO, KIT
74LS283 4-bit binary full adderXO-95KI2

74(S30 8-input “NAND” XO-432

4801 1K x 8 RAMXO-193,Kia

7415245 Octal Bus Transcener — XO-79 xi 4801 1K x 8 RAM XxO-193

2128 (BGB) RAMXO-195KIS
2128 (BGI) RAMxO-195,KI6

741886 Quad 2-input exclusive XO-435 “OR" gate KI7 7415273 8-Dit register xO-94 741820 Dual 44nput “NAND” gale XO-430 14, 15, Lb, L7-8

741S283 4-bit binary full adderXO-95uo
741S32 Quad 2-nput “OR” gateXO433LIT

741504 Hex inverter xO-418

745161 Synchronous presettableXO-488LIZ

binary counter

74L886 Quad 2-input exclusiveXO-435U3

‘OR™ gate 3-14 7415157 Quad 24nput mutuplexer XO-390 7ALSI61 Synchronous presettable XO-440 binary counter DESCRIPTION

74157 Quad 2-nput multiplexer 74LS74 Dual D-type flip flop 745157 Quad 2-input multiplexer 7415245 Octal bus wanscewver 741S374 Octal D-type flip flop 7415157 Quad 2-input muttiplexer 7489 64-bit RAM 7415174 Hex D tp flop 745189 64-bit RAM 745161 Synchronous presettable binary counter 7415157 Quad 2-4nput multiplexer 7418260 Dual Sunput “NOR” gate 7415298 Quad 2-port register 7415157 Quad 24nput mutupiexer 741800 Quad 2-input “NAND” gate 741530 8 input "NAND” gate 741886 Dual 2-input exclusive OR” gate

745189 64-bit RAM 741804 Hex inverter 741832 Quad 2-input “OR” gate 7408 Quad 2-input "AND gate 93422 256 x 2 bipolar RAM 74LS02 Quad 2anput “NOR” gate 741S74 Dual D-type flip flop 7407 Hex butfer/ariver 741830 8 input “NAND” gate 74SI61 Synchronous presettabie binary counter 7415379 Quad D-type flip thop FGO 2764-3 8K x 8 EPROM FGI 2764-3 8K x 8 EPROM FG2 2764-3 8K x 8 EPROM FG3 2764-3 8K x 8 EPROM 7415157 Quad 2-input multiplexer 7418260 Dual S-input “NOR” gate 741832 Quad 2-input “OR” gate 741808 Quad 2-input “AND” gate 74504 Hex inverter 741820 Dual 4-input “NANO” gate 74S161 Synchronous presettabie binary counter 74LS166 B-bit shift register 741S74 Dual flip flop 741S20 Dual 4-input "NAND" gate 748161 Synchronous presettable binary counter 74574 Dual O-type pos. edge trig. fip flop {T.1. only} 74504 Hex inverter PART NO.

xO-Nd xXO-434 XO-124 xO-79 xO-96 xO-390 xO-88 xO-442 xO-89 XO-488

xO-390 xO-93 xO-NB xO-390 xO-427

XO-432 xO-435

xO-89 xO-418 XO-433 xO-404 xO-100 xO-428 xO-434 XO-384 xO-432 xO-488

xO-98 xO-489 xO-489 xO-489 XxO-489 XO-390 xO-93

XO-433 xO-86

xO-400 X0-430

xO-488

xO-391 XO-434 XO-430

XO-488

xO-87

xO-400 war eiioo: Sincad

pvt

——» 70 P3/P

To P1/P2-2¢

NPL ey sens / bb EEL SENS yg 70 pe/pe-!

2ooNivecaneTo peipe- |
@Sokoriz syne58 Dares)

+5) (source)

+tLSv DC | pe CSouRCE) 1 ep 24e+—SS 2 ________» To P5/r6-I8 eer SS5g ——* 73 barnett as TO P3/P6-1S

3<{S2IN RETURN

ie Ba +5

30:

& Pp

$s $

Lip 47 Wy airae Peaster t eared +

208+

Sa a2 + 18: 19e te to

Srgx0r04

ano

Page 18

X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS

ADDRESS BUS

a

1a2ABpata sus—_4
$iF? Ba septsait

Ta] AOdRESS 48 Fis: AIL S40 ator 5eby BY

z[6° 7415373 6)A
He7”Bt

mee waasa

25nea

til \

12.Ho Ck 4aaKa
iST? c3 24hAxaz
toustse® hisa

7 5

we4 ep T9373 c 16.a= as,

wD

;aras 35~a12
0a)aa CIG | CI4-15 | C13-14 | C12-13 | Cl

+ Pas at] 42 Rom + ane ART ROMT | ROMS

AN 2764 | 2764276+27et276¢

A

ita NMIae } t¢De4fr
2373Hoe3

fa TRANS 3

—Aaceiver 84]17]
24] INTA3 na T5245, fd 1de
1230] HLDAAT.67.
ré34] ssoorg PtFis=
8Ree._=
18Nh 2 4i
INTRwa fyGr hen
=62]it28
RIB12
°2 Ba Yneat BY,
Howe10/m $28vo.EPROM ypetea
aT4SELECTTALS eg
ry cd4 ieee asiea
:Ge %T Sava ranger
=3PO ron] ty
1i30/M
=iiaT

TT PG-6

171==0 P3/P4:
(4.7K x 8)ae-]'
ReSa“hy f2—2
rat15/42 Bl] Mes:
RZ+tTrl eaaauFFEReM
eS7ther une ifs 2
xd"383 DRIVER 3p Fs
setese ahsx

WR

give Teshee fer fox ee Jer Jos TeqZt=

(4.7K x 8) a

Ri~eanaoS
i+rajeeseurrerF
=atf0
7AN ORWER 2IP)ADa8
netSlits sea 3 raTileA isATels
“bata* Bio 8e BO yt
Fi;Wands Pore,Aeweetpd 15] goinmur
PORTfotk
neoreeeaSgt
TYP) oUFAlT2TPB ISH yg HST Ga+o SEEGA
Gye)INPUT:

FROM

INTERFACE BOARDLO], ro p5/04-10;

ASS (OPTION: socket Re opt sv sie 4 @rkxs) le ci br

oof 3h3344}at
aeeay

gant RBI

Sra miaeEPane

hi

ora wis1Es az rascaig

" B13 mc) SwiTCH

Page 19

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 20

ADDRESS BUS nn

DATA BUS

it oat RBS s2ea~e

RY

Rew RGaKEsoo*

Racked SEIESTAG SCOUSeL.

| BRSEL

| FRSEL XTAL SI hese Ret 20H pg) TOF na f° cst , 3 100 > + [5 PE 1 K 14.

L13-14 CLOCK Logie 14504

HORIZ COUNTER, 2 Key

  • $08

<+KD1 {HORIZ FLIP Ze VERT FLOP LE/® PRioKTY Boepri 8 sou one

LVERT SYNC I VIDEO GND 18 cHORIZ SYNC

ra ry eye + a < Hit SSS

DESIGNATIONS PI THRU 26 ARE INDICATED FOR REFERENCE ONLY, HB CH BLANK) if P R54 741530

KIS, 74S50¢ oP >oe_t BLANK

EIT VERT SYNC

DIE ¢ EIG y Veet Latcnes

Page 21

X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS

HHg* VW FRWR HORIZ FLIP ng —FRWR _

HHEpeoof
HHI0.be

J13-6 fis a i

FI5 741804.np 2Of
12HHSAl 3),

>

+AeGq T4U5139

o ET 7 744886 BGAI

HHI HH KIG TZ, 141502

maszte,(__,_S 16 StBak

T4586, Gie 4Gl7 KI¢ stew

Hie € HI7HoriZHs
HORIZ FLIPLATCHES3El

FoR ¢.T. K13,741832 54 LATCH CLOCK H2

Ai to

HH> T Hoa HHS, HHE HHT Ae 2 Ay [23s] ISIS [FS

HHB

ih FOREGROUND RODRESS. ¥3 PEORAZ, iS 14 HIT 6 “Yyrais8¢ Y KiB miss 12 Fo

ma FORAZ Foray D2, D3, D+ Ze ROY1 231 MUX

BRSEL FRSEL SRIFTED 4 BLANK

FI.evspsn _| 0,£3 VH BLANK
|alse poNee aleqial |
Ta:741508]KIq141500sB8w
K15, 74504T4508YBUANK
UPot2We

N BLANK K15, 74504 ANS vva vV3 VWVe

E\S incuo> FoRegrounn
74.386$8Roeess
O15 £15HRlat
MW VERT FLOP FOR C.T.T4932,NNVE

3 vv5

6|VV@

5 of) >—2 YVT VERT DIS LATCH FLOP T4986

Page 22

LING oszecT Ht tary HF ooSiion ena G4 Gs WBLANK LINE RAM ADDRESS COUNTER or 1 ot

Be__&) pabeswalewa Cais

03 p ee

D+8QlRESIS GT yetfeal
333) peapy)LEA74157. Lo evaal
Deio] 52ets|NapoEBAY
ortorSun | Y ie Fos]

48 £4 s aa

=FOREGROUNDa.

veRr (oN 4s i FOR! Hee 1g 33019 mal FuRac aT] AY Ha FORAZ 1 AS ME ag [EERE 3 as g Qe) ca 3 FS€ES eG ¢I8 VERT PosiTION TINE RAM Lee ENABLE PULSE GENERATOR ° rls .

bg4rakeype
a! ote165GI x oerais32
Hehee Ke T5LsI5T 2 aro?)Erpog 2 [
bea)Fong a1 ASi siFeepi5]h)
59] OtaR5]FRB02 1) 45,
D610] 8+5v(hsteRa3 4

06 7

ori] $FTsale

@ - 7 + 8 EZ siP72 Gl éG2

=FOREGROUNDOKx8) 27 MUXHORIZONTAL

HORIZ POSITION : POSITION DATA T4804

G3,G4, 45 LINE OBTEcT P SELECT RAM MUK

FOREGROUND “= | OBJECT SELECT

T\ tary TG LINE OBJECT SELECT RAM

LOGIC BOARD ASSY. (A1), SCHEMATIC DIAGRAM, SHEET 2 OF 3

Page 23

my +-oOP

a

+

ck

Liz B00NS COUNTER

ra

15 745161 fe it RAD cK +, ”

Kd THRU KB FOREGROUND OBJECT ROM

KI,K2,K3 JECT ROM E55 LA TCRES

Page 24

X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS

Fore viog 3 fT Fore vit 4% At} Jat. Ya Fore wib2 21h, 4412 vA FORE ViD3- 7 baa misgag Ye BACK VIDB s BACK Vip 11] 2:1MVx BACK ViD2_5 BACK VIDS @ Stee |

Hi] By TALS260

W (0P30 = OPTION

KI2 ALSROO &

all

Hu TALS2GD Raya aa 74.902 = JUMPER,

SUMMER, ak (set

FOR,

gpa

~---O TP22

BRAZ 6 | 4. eraas|,, ET Baad 4 14. 48 | LRA Lhe BRAG % BRAT { BRAG 23 |g BRAD 22 Az 8 ag HLS2HS Bs

E9-10 DMA TRANSFER,

BACKGROUND CHARACTER REGISTER, 08, D9, DIO 1.eus STATE /ADpRESS CONTROL

BBRAS 5 M2 Eto 7 AZ tte 02)

RAM

VH BLANK

Page 25

ja ADDRESS BUS

a DATA BUS

C13, C14, C15, coLoR RAM Q86 MPSATO Die Reo BREEL 013 G13 eset te big 7489 02 > a

BOTRSEN [3]

meee a ei COLSEC OLS: Biko

oa RBG 0 GIS bee bie 7489 bes

mesaro GREEN

7 age MPSATO RSG

BLANK

T4LS86 tnas R92 tk

PRP O e) TAL TO ANAL DIGITAL (Al $e. 11,012,013 Xioeo suvroTeV PESO 1 AAT BACKGROUND oBTECT : 5 2 BAM ADDRESS BUS

oat 6

EIA EN3 BACKGROUND CHARACTER RAM

BOTRWR/OTRAIZ

ora 378

oreats SPO)

orpa IP

LOGIC BOARD ASSY. (A1}, SCHEMATIC DIAGRAM, SHEET 3 OF 3

Page 26

X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS

POWER SUPPLY ASSY. (A3], COMPONENT LOCATION

P62 comang 1983 ae urerantecraoucs nc, GB" IF HYESTAR ELEETBOMEE NC. ~ERED oP fewen'surrcy en" tana ‘ En

POWER SUPPLY ASSY. (A3), PARTS LIST

REFERENCE — DESCRIPTIONPARTREFERENCE—DESCRIPTIONPART

No. No.

Power Supply Assembly MA-479 RI2 Resistor, 100 OHM, 5%, 1W XO-137

CM, C32, C42,Capacitor, .OIUF, SOVXO-229R13, RI4Resistor, 12 OHM, 5%, 3W/XO-138
C55, C7}RISResistor, 200 OHM, 5%, YWXO-143
czCapacitor, 1OOUF, 16VXO-235RI7, R52, R53Resistor, 100 OHM, 5%, «WxO-28
13, C57Capacitor, .1UF, 50VxO-558RigResistor, 20 OHM, 5%, AWXO-29
Cl4, C33, C43.Capacitor, .22UF, 35VXO-615R22Resistor, 470 OHM, 5%, YWXO-55
21Capacitor, 2200UF, 25VXO-346R31, R41Resistor, 560 OHM, 5%, WWXO-36
c3rCapacitor, 1SOOUF, 35VXO-616RSIResistor, 511K OHM, 5%, AWxO-40
C41, C54,C72Capacitor, 470UF, 35VXO-284R54Resistor, 220 OHM, 5%, /2WXO185
C52. C56Capacitor, 1UF, 35VXO-715R55Resistor, 22 OHM, 5%, «WxO-595
C58Capacitor, 1OOOUF, 25VXO-218R56Resistor, | OHM, 5%, 7WXO-593
C73, C75Capacitor, .JUF, 35VXO-614R70Resistor, IK OHM, 5%, &WxO-5
bit, 025,Diode, Light Emitting MV-5752XO-270R71, R73, R77Resistor, 10K OHM, 5%, MWxO-18
035, D43R72Resistor, NOK OHM, 5%, ‘4WXO-591
bizDiode, Zener, 5.6V, IN4734AXO-255R74Resistor, 560K OHM, 5%, “WWXO-704
Dai-D24,Diode, IN5401XO-263R75Resistor, 2K OHM, 5%, “WWXO-14
31, 33R76Resistor, 4.7K OHM, 5%, WxO-7
32, 034, 036,Diode, 1N4004XO-254R78Resistor, 100 OHM, 5%, WWXO-52
D41, 042, D44SCR68-1Silicon Controlled RectifierXO-131
D71-D75Diode, 1N4148XO-261uitVoltage Reguiator, Zener TL4310-272,
anTransistor, PNP, 2N5879XO-323U3!Voltage Regulator, -12V, LM340K — X0-628
azTransistor, TIP31BXO-641ualVoltage Regulator, -12V, LM320T—_X0-613
a7Transistor, PNP, 2N3906X0-588ustAudio Amplifier, LM200TX0-550
72Transistor, NPN, 2N3904XO-549u7IC, CMOSX0-564
RIL, RI6Resistor, 180 OHM, 5%, WWXO-24veiPotentiometer, 100 OHM.X0-134
Page 27

X. WIRING AND SCHEMATIC

Qu 2N5879 al +14.5V OC 4.5.31 T oe, ; j HS.1

R14.

073 ts

*UPI3at

t 8 un

oraMC145368—

6 = TN4148,

R75 P7? 2k

sel

AUDIO INPUT 1 + bel 12V AC + 656

IN5401Percs21UF, 35V
pez°1UF, 35VTDA,TANT,
s—_TANT,2002;
+13.3V DC AVG.zi1
  • KA —_
4athecaR222c
3SBOUF470, /2WR52
-5VMy.
T 12v AC RETURNyBARA vyj

Vv R53

sey AC: 1N4004 2€ t 15401, 1N4004

031D32[==
eeea-+21V DC AVG.in} ust lout
ialttLMB40K-12
ssoours?heseL_T03_Icgg—* at
3 | KEY033'W 034 | 35vToiuF GNOTO.22uF, FU aw
15V AC1N5401 | 1N4004]L"sovTANT.I,
1G===35,

MV5752

Day042-|
1N40041N4004~2iV DC AVG.++ .

cat c42 A70UF =< .OIUF == 7 35V +7 “50V

Deaii i es
Page 28

ATIC DIAGRAMS, PARTS LISTS

+5VDC 6.0 A

RESET

x a g

R74 560K v

NOTES: 1, ALL RESISTORS ARE +5%,

2, ALL NON-POLARIZED CAPS, ARE CERAMIC AXIAL.

+ Losic crouno

‘W ANALOG GROUND BESO ONTASUN—N

ol

AUDIO OUTPUT v oO

x isl iw rn

4a 1N4004

fl u4t UT NY umszor-12 {2

TO-220

+ [ GND =12v OC OWA TI 510 c43 | Ray a Q.22UF 3560, 1/4W +20V DC AVG.1.0A ny TANT. fy | ares

MV5752

POWER SUPPLY ASSY. (A3), SCHEMATIC DIAGRAM

Page 29

X. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS

SOUND BOARD (AG) COMPONENT LOCATION

SOUND BOARD (A6) PARTS LIST

REFERENCE DESCRIPTION PART REFERENCE DESCRIPTION PART

No. No.

Sound Boara AssyMA495ReResistor. 240 OHM, 5% “WW—-XO-I73
acCapacitor, 22°F, 50V MONOXO-633RI IZResistor. 470 OHM, 5% “WWXO-35
‘AX-CM, 10%RiaResistor. 68K OHM, 5% 4XO-8
3. C21Capacitor. O1UF, S0V MONO-X0-637R15, 820Resistor. 12K OHM, 5% KWXO-175
AXGLRIG, RI? RIV.Resistor. JOK OHM, 58% AWXO
5,6Capacitor, O1UF, SOV MONOXO-747R26, R29, R30,

‘AX-Gl, 10% 232, R37, R38.

7,17. C23Capacitor. UF, SOVCM-RD-XO-294R60-RE4
Non-PolanzedR36, RASResistor, 33K OHM, $% AWXO-43
€B,C9, CIOCapacitor. 1OUF. 25VxO.27SIP) SiP2Resistor Pack. Sip, 'K OHM, 9 Pin XO-493
CB, C19, C24,TANT-AX, 10%swt, 9w2Swaten, Push Button, NOXO-365
asXTALLCrystal, 40 MHZXO-366
aCapacitor. JOPF, SOV AKC,XO-435XTALZCoystal, 312 MHZ0-639
+80%-20%24 Pin DIP SocketXO-529
13, €20Capacitor, JUF, SOV TANT-AX — XO-21728 Pin OIP Socket0-536
ceCapacitor, 68°F, 50V MONOXO-63640 Pin DIP Socketx0-530
AX-CM, 10%Az7430 B-input "NAND" gateXO-643
asCapacitor, 047UF, SOV MONOx0-63843, 827415373 Octal D-type fp flop KO-445
AX-CM, 20%Aa741574 Dual Diype flip topXO-434
(ALL UNMARKEDBI, HM324 Quad op-ampxO-6A4
CAPACITORS—OIUF. SOV CM-AX0-230837415284 Octal butfer/xO-7

line drver

ALL UNAAARKED:2‘AD7528) OACxO-647
FOUSRIZED)£3, G3. N657415374 Octal D-type fp opXO-96
CAPACITORSIOUF, 25V TANT-AX, 10%,xo.127fe570250 Speech generatorKOnE
oOioe, 645752X0-270an741504 Hex inverterxo-418
or swDIP Suaten, 4 Position,8Pin——-XO-640os741508 Quad 2anput “AND” gate XO-86
Phone JackxO-7442, Ha4801 1K x8 SRAMXO193
3 Pin Water Conn,x0-703Ha. ka‘AY-3-8913 Sound generatorxO-646
9 Pin Wafer Conn,xO-375HS, KS. NS,7416} Synchronous presertable— XO-192
Resistor, IOM OHM. 5% “WwWXO-73Si.binary counter
Resistor, 1K OHM, 5% AWxO-5K2. K3..N3.27324 4K x8 EPROMxo485
NTS6502-13 CPLx0-360
33-835, R39N2, 837US245 Octal bus transcewer — XO-79
3. RIBResistor, 4 7K OHM, 5% “W—-XO-T27415139 Dual} of 4 decoderXO-AI9
6. RRB,Resistor, 68 OHM, 5% 4WXO-748174(S)38 | of B decoder/xO-437

22-824 ‘demultiplexor eomeeaee gee nseaeab ee @eem oss =] s]— 3 =

Page 30

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 31

MATIC DIAGRAMS, PARTS LISTS

Sha. PA ac Pal 5 ‘ oa tov D3 ‘ oe sis 08 out! ee by A i is Ra 47K 620 vir

80 250 Reset DATA PRES

VL of

Hoag ag, f ne i | PET eb ae S [tox

ar? Leet) coslcos PL

TANT] FARTING HA) Tee tN poton Tesy | SASV oven nie ay te :

= SS SS ‘EPs SHORE ay oot | tN Tee Tee

t ADDRESS BUS 1 + 1OUF 8

25V. TANT.

13 From s2/3 s Ha —< FROM 73734-Nart~ H3/27 ar Hi< FRom 73/38- Tae +12v 0c FROM S2 i> 1 H2< FROM G4/12- N3/22- *3/22- 43/20 + Souk; reg 25V TANT.

TO JCT. OF “| BN R34 AND 65-1 HANTS + = common Grouno ab =annizs, crouno

SOUND BOARD ASSY. (AG), SCHEMATIC DIAGRAM

Page 32

(ceiceeiceestiaentientiaatoentetiaettenttatantantostantandientien ' — r Fa | i an [E33] 124 (aFF

|Ataaa}

| BOTTOM PANEL assy. | |!

sweMA-6181 fl av AC
FRONT DOOR!1 jy} RETURN)

INTERLOCK Hy

iorl: it22
1aeFe
[Foo2? peWy4a
reel 3 <lre2ltSLO-BLO
H T3A[SL Qpeto
H :SLO-BLOioeF624
NPT [om: 'FILTERf 40; [faa] 15V AC_SLO-BLO
%::
POWER33 <4 <} FAee|| £14, WSS] 1svac CENTER TAP (1
115V AC: Hi +TEoA
S0Hz/60HzNOTE:H H1 lie! GFzjisvac s1d-BLo
thINTERLOCK SWITCH ' irla
SHOWN IN DOOR OPEN! HnlFly
TOPOSITION.H H' (44 [oss] 2vAc_1 5A
BANDS8 ''SLO-BLO

Hy 5 i [FOO ! 1 (70 SERVICE | Ss I<; OUTLET if : : soll [655] 42v Ac (RETURN)

H :niF2
FT og| 941A

i : i ;6.3VAC — SLO-BLO

,pq M2:sl3V AC (RETURN)
'2B22) | os,| |i) Vee tesl Sv Ac URETORN) —
1!ri!iiisER
H‘1 Ul 3) peo,
ll¢PHBL ioe|e attsvac isco
]!:I|§ 4 toov ac

ON-OFF!

|SW.GNDH,_4y (877] COMMON

STARTER ‘ 1 iLiumination assy, | i

LMA-622H

Al2 : “ comi £3.53 (eT gt

MONITORHi tE 7
aeb>2>t PELs 822]+
<a— 01L_

en aaa ereraciertpetonn]

IVATAQ CONTROL PANEL ASSY. |
Oe?| DIODE BoaRD VaraotMA-1178as
Pitprtv2 P2 OG
c2\qo maa]oS LARRY UP og<2 <, 1300
ty o> _lssl7% LARRY pown 7 HEx
com 21bd nore ee) ts 5}AG LARRY LEFT-322
i} +jG@—t>o> TTgt oS LARRY_RIGHT333
HHH
:1 [800] |tA,
‘COLOR CODEHt-—>9 >aSOMOE SE+
]bq 's10>BALES, Hi o> MOE_DOWN +
°H:> 6
1|fq1 > BLMOE LEFT+
oT REDIfy12>}gt oS MOE_RIGHT
3_|_ ORANGE:HHH
=HHi
4 | YELLOW|qo 13 > a44 iso >4 7 LU RLY_UP.
S1fg a>t PEL ot 9 % SURLY DOWN
61bg Si5>i_[esel Sit7 SURLY _LEFT

7 | PURPLE 1 tp igs S77] } a H 7 SURLY_RIGHT

!ia=
|) t'|LARRY SLAP/THROW344
pares:|iwe7o |:|AMOE SLAP/THROW 17 <1 [865
i}(2) 6iH
1, [251 invicaTEs WIRE COLOR.::| eSuRLY_sLap/ THROW |aE
2, INDICATES CIRCUIT GROUND.i}:'©-e<
3.,}, INDICATES EARTH GROUND.!iiLJ
4. INDICATES .O1UFyt rss733
S.n% INDICATES 39PF| LaL frezrs
|ty e>t7
Page 33

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 34

| aren | avl | Wey Pt i] ~< B<+ I bec]! \ +< fet 4 < he I bc jet I

Pea)HH
Pia1 37 (O7A' e< t|
i3>1 balL< bet|
+to 4 > =Lcd <r|

$e 5 > 25<-

xe7i1
zoel tigreees
: pal pret246It
A KEY,ol‘
LAR <_— wreR BOARD‘f

LK 2<t | T 3<— I —~<28<+ 29 | L e30e+- | 1 7 (4 11.5V DC) FROM ABJI-~6 annanl , I

ol eieteieieieieier 1a‘;
P:=o;:
2<r6 >><< Z<
3<>a >} btL<ezet|
4 | KEYKey; 3:H|
1<b> >+ aa<a<
S<ri> 1 >+S51~<23<4I
e<Bseve
isSOUND BOARD ASSY.13320 esaree
9 7MA~496ise >i fez2lLc 13<4|

; i At

'|;HLoGic BOARD ASSY.|
i}!LigMA-646|
AS pti}ya1

2 < AUDIO :

INPUT,i]FROMocMorS|
1 <-(souRcE)FILTER BOARDonl!

x<€ H I

—y_occcctspeaKe:
TasonM”<a|

tsenvicer PANEL AUDIO OUTPUT , i

1 omacesa — [YOKPMELwetI
Ww:|

eet I

iLics<t\
a>=== COIN METER<r etI
:Test:'1
nSELECT TEST SWITCH‘Hi
TEP TEST SWITCH‘ vet|
Laerire!
_S13 PIBP6 us‘H|
—— = eeaanaeM:'
40ono SLAM SWITCHBg aaa opal - Diss j Bad t cygetI
v3 oF COIN SWITCH #1ie3ci GO eySF* HH1 fod tec
77> GOIN SWITCH #2coe Me I E*iys>! Mgt|
|=I!|

COIN CHUTE

= weeLa AJ|
'i]P/OlI
|FRONT, DOOR ASSY.i]FILTER BOARD||

“6 4 LS Leaoo-. J

PRIMARY POWER/FILTER BOARD/INTERCONNECTION DIAGRAM

Page 35

XI. PARTS INFORMATION

TABLE OF CONTENTS

PAGE

SPEAKER/MARQUEE ASSY. .............. 34

ILLUMINATION ASSY. .

CONTROL PANEL ASSY. .................. 34

SERVICE PANEL ASSY..................... 34

BOTTOM PANEL ASSY. ................... 34

CABINET PARTS (INTERIOR) ............ 35

CABINET PARTS (EXTERIOR)............ 35

FILTER BOARD

Page 36

ITEM

1. 2. 3. 4.

8. 9. 10. 11.

ITEM

2.

3. 4. 5.

ITEM

1. 2. 3. 4.

6.

ITEM

OurRONE qT 8.

10. 11. 12. 13. 14. 15. XI. PARTS INFORMATION

SPEAKER/MARQUEE ASSY., ILLUMINATION ASSY.

DESCRIPTION

Illumination Assy. Starter Ballast (60HZ) Lamp, Fluorescent Cable Assy. (Illumination) Speaker Assy. Speaker Speaker Grill Illumination Trim Cable Assy. (Speaker) Marquee, Lexan

CONTROL PANEL ASSY.

DESCRIPTION

Control Panel Assy. Short Button; White Green Blue Button Holder and Switch (3) Joystick (3) Cable Assy. Lexan Overlay

SERVICE PANEL ASSY.

DESCRIPTION

Service Panel Assy. Cable Assy. Switch (Pushbutton) Switch (Toggle) Volume Control Coin Meter

BOTTOM PANEL ASSY.

DESCRIPTION

Bottom Panel Assy. Transformer Capacitor, 50,Q000UF, 25V Resistor, 200 Ohm, 5%, 2W Fuse, 3 Amp, SLO-BLO Cable Assy. (Secondary) Fuse, 1 Amp, SLO-BLO Fuse, 12 Amp, SLO-BLO Bridge Rectifier Fuse, 2 Amp, SLO-BLO 1.5 Amp, SLO-BLO 1/4 Amp, SLO-BLO Service Outlet Line Filter Cable Assy. (Primary) PART NO.

MA-622 EL-69 EL-70 LA-4 MA-626 MA-459 EL-83 20931 23067 MA-318 24080

PART NO.

MA-1178

21970 24041 24042 21971 23189 MA-633 24079

PART NO.

MA-620 MA-624 EL-57 23506 X0-199 EL-84

PART NO.

MA-618 23149 X0-342 XO-142 EL-9 MA-630 EL-6 FSI-83 EL-42 EL-7 EL-34 EL-5 18133 EL-50 MA-631

Page 37

ITEM

1. 2. 3.

4.

6. qT. 8. 9. 10. 11. 12. 13. 14, 15. 16. 17. 18.

13.

ITEM

A8P1 A8P2 A8P3 A8P4 A8P5 A8P6 A8P7 A8P8 A8P9 A8P10 A8P11 A8P12 A8P13 A8P14 CABINET PARTS (INTERIOR)

DESCRIPTION

Back Door Interconnect Cable Cable Assembly, Master Electronics Bottom Panel Assembly Sound/Speech Board Assembly Power Supply Assembly Logic Board Assembly Filter Board Assembly Shield, Top Shield, Bottom Clamp Bracket, Shield Cable Assembly, High Voltage Cable Assembly, Monitor Cable Assembly, Front Door Line Cord, Bushing and Plate Rear Door Lock Anchor Plate, Lock Slam Switch and Bracket

CABINET PARTS (EXTERIOR)

DESCRIPTION

Lexan Overlay Side Decal (2) Top Glass CRT Frame Monitor Filter Glass Monitor Mask Monitor Interlock Switch Cover, Interlock Switch Leg Adjuster On-Off Switch Switch Plate Vent Channel

FILTER BOARD

DESCRIPTION

Filter Board Assy. 6 Pin Wafer Conn. 9 Pin Wafer Conn. 10 Pin Wafer Conn. Pin Wafer Conn. Pin Wafer Conn. Pin Wafer Conn. Pin Wafer Conn. Pin Wafer Conn. Pin Wafer Conn. 10 Pin Wafer Conn. 8 Pin Wafer Conn. 7 Pin Wafer Conn. 4 Pin Wafer Conn. 7 Pin Wafer Conn. Capacitor, .O1UF, 50V CM-AX +80%-20% (38 each) Capacitor, 39PF, 50V CM-AX (6 each) Ferrite Bead (22 each) Ferrite Bead (66 each) OAANARAO XI. PARTS INFORMATION

PART NO.

23073 MA-635 MA-636

MA-618 MA-1181 MA-479 MA-1182 MA-457 22632 22633 22631 MA-619 22620 MA-625 23366 23975 23967 23791

PART NO.

24095 24103 24039 24081 22849 22463 21981 EL-66 21888 MH-21 23799 18769 21754

PART NO.

MA-457 X0-373 XO-375 X0-336 CO-339 X0-335 X0O-369 X0-335 X0-373 XO-375 X0-336 XO-339 X0-335, X0-369 X0-335 XO-229

X0-334

X0-337 XO-338

Page 38

LIMITED WARRANTY

Mylstar Electronics, Inc. warrants to the initial purchaser of the Mylstar Electronics, Inc. machine that the items listed in the following schedule as installed and used in the original Mylstar Electronics, Inc. machine will for the applicable period set forth in the schedule, computed from the initial date of purchase from an authorized Mylstar Electronics, Inc. distributor, be free of defects in materials and workmanship:

SCHEDULE

GAME ITEM WARRANTY PERIOD

Pinball All Electronic 90 days

Printed circuit boards Pinball-Video All Electronic 90 days Printed Circuit Boards Card Cage 90 days Television 30 days Monitor All Electronic 90 days Printed Circuit Boards Television Monitor 30 days Video Disc Video Disc Player 60 days

This Limited Warranty does not apply to any parts damaged in the course of handling or assembling by the customer or damage due to other than normal use or use in violation of instructions or reasonable practices, or further damaged in return shipment. This Limited Warranty is made only to the original customer, and is and shall be in lieu of all other warranties expressed or implied, and of all other obligations or liabilities on the part of Mylstar Electronics, Inc. and in no event shall Mylstar Electronics, Inc. be liable for any anticipated profits, consequential damages, loss of time, or other losses incurred by the customer in connection with the purchase or operation of Myistar Electronics, Inc. machines or components thereof. The registration card with each Mylstar Electronics, Inc. factory-wired machine must be filled in and returned to Mylstar Electronics, Inc. within ten days after date of purchase for this Limited Warranty to be effective. This Limited Warranty applies only to machines so registered. THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER- T,

CHANTABILITY OR FITNESS, AND OF ANY OTHER i da SON ics

OBLIGATION ON THE PART OF THE SELLER AND _ ELECTRONICS, INC. INC. ——"

Page 39

MYLSTAR ELECTRONICS, INC. 165 West Lake Street Northlake, Illinois 60164 Tel (312) 562-7400 Telex 72-8463 A Columbia Pictures Industries Company e e e e rs rs * s e e rs r e

e e e e r e e

1984 Myistar Electronics, Inc. All Rights Reserved Printed In U.S.A. 5-84