Crash
Crash (set 1) (Exidy, 1979) · Manual · 29 pages · 16 sections · original scan
July 1979 (c) 1979 EXIDY, Inc.
CONTENTS
I. GENERAL .......... ge een eae ee eee
II. NORMAL OPERATION
A. Attract Mode ..... 4 B. Introduction Mode 4 C. Game Play ........ 4
III. SELECTABLE OPTIONS
A. Coinage ..........- ae) B. Crashes (Turns) ... eC C. TOP THIS SCORE .... vere 5
IV. AUDIO ADJUSTMENTS .....-..-.-------5 ecw cc wcceee 5
V. POWER SUPPLY ADJUSTMENTS .......2..+.ee000% yeweee | 6
VI. MECHANICAL ASSEMBLIES
A. To Service Early-Production Control Panels 7 B. To Service Late-Production Control Panels 8 C. To Service the Four-Way Joy Stick .... 9 D. To Remove the Monitor 26 eeee ween en eens - 10 E. To Remove the Logic and Audio Boards . : 10
VII. TECHNICAL INFORMATION
A. Logic Description and Operation ...... cm B. Audio Description and Operation ...... 1 C. Diagrams, Pinout Table, and Schematics 14
ILLUSTRATIONS
Figure 1: Monitor Display ... eeceeees 3
Figure 2: Audio Board Adjustments .....eseseeeeeeeee 5
Figure 3: Power Supply Adjustments ... 6
Figure 4: Control Panel (Early Production) ......... 7
Figure 5: Control Panel (Late Production) ..- 8
Figure 6: Four-Way Joy Stick .....s..seeeeeeeeeeeeee 9
Figure 7: Major Internal Components ...... «=. 10
Figure 8: Logic Board Block Diagram .........+.+ rae |
Figure 9: Audio Board Block Diagram .. oe 15
Figure 10: Harness Diagram ......seeceeeeeeeeceeeeeee 16
I. GENERAL
CRASH is a one or two player skill game in which players drive a car around a five lane square track while avoiding collisions with computer controlled drone cars. Players score points by driving over speed dots marked on the traffic lanes; players avoid collisions by changing lanes at the four traffic interchanges, and by using the FAST button to beat drone cars to interchanges. CRASH has three coinage options. After the player inserts his coins, play instructions and the day's high score appear on screen. An optional TOP THIS SCORE feature gives a replay to the player who beats a random score.
The operator selects the number of crashes (turns) per play: 2, 3, 4, or 5.
PLAYER +1 DRIVING
Figure 1:
1 Traffic lane 2 Interchange 3 Speed dot Monitor Display
4 Player car 5 Drone car 6 Message panel
II. NORMAL OPERATION
A. Attract Mode
When the game is first turned on, the words GAME OVER will flash on screen. Also on screen will be TODAY'S HIGH SCORE followed by a score which changes with each new higher score attained throughout the day. When the game is turned off, the high score is reset to zero.
Also displayed on screen, at the operator's selection, will be one of the following:
COIN PLAY Ds srsvesie. ste, stateless ye il
or
or
CRASH also has a coin accumulator (credit counter) so that a player can buy a number of games in advance.
While in the attract mode (no credits, no game in progress) the game plays automatically.
B. Introduction Mode
When a player deposits a coin, the following message comes on screen:
CHANGE LANES TO AVOID CRASH WITH OTHER CARS
10 POINTS FOR EACH DOT BONUS POINTS IF ALL DOTS ARE ELIMINATED
CREDITS N
TOP THIS SCORE FOR CREDIT
M Here, N is the number of games in the credit counter, and M is a random score used by the TOP THIS SCORE feature. At the operator's option, CRASH awards one extra game to any player who matches or exceeds the score M.
Cc. Game Play
When a player presses one of the two START buttons (after coinage), a fanfare tune signals the start of play. The player's car starts at the bottom center of the screen (in the outer lane) and moves counterclockwise. One drone car starts at the same place, moving in the opposite direction.
The drone car tries to crash into the player's car. The player must avoid crashes by changing lanes at interchanges; he uses the FAST button to reach an interchange before the drone car.
When the player's car drives over a speed dot, the SPEED BEEP sounds and the dot disappears. At game start, each dot scores 10 points; if the player clears all the dots in a single turn (without crashing into the drone car) the playfield is reset, and all speed dots score 20 points. Each successive time the player clears all dots, the dot score goes up: 20 points, 30 points, etc.
The number of drone cars increases with the point value of the speed dots. At game start (10 points per dot) only one drone opposes the player; at the next level (20 points per dot) two drones oppose him. At all succeeding levels (30 points and above), three drones.
A turn continues until the player crashes into a drone car. The message display in the center of the screen shows turns remaining, by aisplaying one car for each crash (turn) left, not counting the current turn.
III. SELECTABLE OPTIONS
CRASH has three switch selectable options. These are controlled by a seven segment DIP switch located on the main logic board at position 14A (see Figure 2, switch is acccessible from the front of the game though the coin door. item 6). This
Following are the options and the switch settings for their selection:
A. Coinage
2 Player - 1
1 Player - 1 2 Player - 2
1 Player - 2 2 Player - 4 Coin
Coin Coin
Coin Coin
B. Crashes (Turns)
2 Crashes
3 Crashes
4 Crashes
5 Crashes
Cc. TOP THIS SCORE
Credit awarded for topping score
Credit not awarded for topping score switch
ON
ON
OFF
switch
ON
ON
OFF
OFF
switch
OFF
ON switch Ls
ON
OFF
ON
switch
ON
OFF
ON
OFF
IV. AUDIO ADJUSTMENTS (Figure 2)
MOTOR -- 3 pots:
R52=high frequency
R53=low frequency
R16=volume
MUSIC -- 1 pot:
R63=volume VOLUME -- 1 pot:
R66=overall volume
CRASH -- 1 pot:
R29=volume
SPEED BEEP -- 1 pot:
R39=volume
SKID -- 2 pots:
R47=frequency
R49=volume
10.
Figure 2: Audio Board Adjustments
R52 MOTOR 6 R53 MOTOR 7 R63 MUSIC 8 R66 VOLUME 9 R29 CRASH 10 DIP SWITCH R39 SPEED BEEP R49 SKID R47 SKID R16 MOTOR
ve POWER SUPPLY ADJUSTMENTS
Connect a voltmeter to the +5 2. Adjust the power supply potentiand ground traces on the logic ometer for +5,0 + .1 VDC (see board. Figure 3).
Adjustment potentiometer
Figure 3: Power Supply Adjustments
VI. MECHANICAL ASSEMBLIES
Each CRASH game has one of two 3. Reaching up through the coin control panels: door, remove the wingnuts from the four carriage bolts that
- A single metal plate, held by hold the control panel down. four carriage bolts (early
production) . 4. Lift the control panel up from
the cabinet and set it on edge,
- A large metal plate, hinged at so that you can reach its the bottom (late production). underside.
- Check all terminal connections A. To Service Early Production to the pushbuttons and the four- Control Panels (see Figure 4). way joy stick.
- Unplug power cord.
Figure 4: Control Panel (Early Production)
1 Carriage bolt 4 Control panel 2 Start buttons 5 Four-way control 3 FAST button 6 Control harness
B. To Service Late Production Control Panels (see Figure 5)
- Unplug the power cord.
2, Open and remove the back door.
3, From inside the cabinet, the three control panel nuts (see Figure 7).
- Open the coin door.
- From the front of the cabinet, pull the control panel out and down; let it rest on the open coin door (see Figure 5).
remove 6. Check all terminal connections to the pushbuttons and the fourway control.
Figure 5:
1 Control panel 2 Start buttons 3 Control harness Control Panel (Late Production)
4 Main harness 5 Four-way control 6 Control stick 7 FAST button
C. To Service the Four-way Joy Stick
The four-way joy stick is mounted on the control panel with four long screws and standoff spacers. Four pairs of spring steel cup washers surround the control stick, between the control panel and the top plate (see Figure 6). These cup washers bear against a disk welded to the control stick, and push the stick towards its center (rest) position. Four leaf switches on the bottom plate (activated by the control stick) signal lane changes to the logic boad.
Figure 6: Four-Way Joy Stick
1 Carriage bolt 8 Kep nut 2 Control stick 9 Switch plate 3 Control panel (bottom plate) 4 Flat washer 10 Kep nut (small 5 Cup washer pattern) 6 Spacer 11 Leaf switch 7 Lower disc 12 Phillips screw (top plate)
at service the control:
Unplug the power cord.
Open the control panel (see above).
Check the harness connectors to each leaf switch.
Check the throw of each microswitch; the control stick should activate, but not bottom-out against, each switch.
If necessary, adjust leaf switch throw by carefully bending the switch actuator with a long-nose pliers.
De To Remove the Monitor
Unplug the power cord.
In some cabinets, the monitor is not accessible through the back door. A monitor access panel above the back door is secured with four wood screws.
Open and remove the back door or monitor access panel.
Unplug the harness connector from the monitor.
Remove the four bolts from the monitor chassis flange mounts. Lift the monitor up and slide it out of the cabinet.
To Remove the Logic and Audio Boards
Unplug the power cord.
Open and remove the back door.
Clip the plastic tie wraps which hold the boards in their rack.
Disconnect the edge connector from the logic board.
Slide the boards out of their rack.
Figure 7:
1 Monitor 2 Power supply 3 Speaker 4 In-line fuse Major Internal Components 5 Interlock switch 6 PC boards 7 Cash box 8 Coin door
VII. TECHNICAL INFORMATION
A. Logic Description and Operation (see Figure 8)
CRASH uses the 6502 central processor unit. (For more information on this procesor, refer to MOSTEK publication #6500-10A, MCS Microcomputer Family Hardware Manual.)
This processor is unique in that it does not have a separate input/output structure, but treats all I/O as if it were an area of memory. Memory is mapped as follows:
FFF8-FFFF Interrupt and reset vectors FO00-FFF7 Program storage (PROM) D000 Four-way control and interrupt reset co00 Option switches (input) A000 Control switches (input) 8000 Player car rotation and audio control bits (outputs) 4000-43FF Screen RAM 3000 Player car horizontal position (controls) 2000 Player car vertical position (controls) 1000-1FFF Program storage (PROM) 0100-01FF Stack RAM 0000-00FF Base page RAM
Base page RAM holds variables while the game program is running; the stack RAM holds return addresses and important data during subroutines. The program storage PROM holds the program which controls the operation of the game.
The screen RAM consists of 1024 bytes (8-bit words) of read/write memory. When not being addressed by the processor, this RAM is scanned by main timing, to display a 32 x 32 matrix of squares on the screen. The data stored in the scren RAM is then used to select one of 256 images from the screen ROM (each image is 8 elements wide and 8 lines tall). Note that the processor never addresses screen ROM directly (see Figure 8).
The 8 x 8 images selected from screen ROM fit together to form the display on screen. An alphanumeric character consists of a single 8 x 8 image, while the player's car and the crash explosion are each made up of several images.
Example:
To store the letter "Xx" in the upper left corner of the screen, the processor would write 29H in memory location 4000H.
The player car is generated by two sets of counters (horizontal and vertical) which are used to position the image on screen. The outputs of the counters, along with the rotation information in 8000H, are fed to the player car PROM to form the car's image. The processor controls the car by preloading the counters to the desired position during vertical sync.
The processor reads data from the switches by gating the data from the control or option switches onto the data bus when the appropriate address is selected.
B. Audio Description and Operation (see Figure 9)
The audio board is powered by +5 vDC from the logic borad and +15 VDC developed on the audio board itself. The AC power source for the +15 VDC comes from an external transformer which steps down the 115 VAC line voltage.
The audio board contains the following circuits:
- +15 vDC regulated power supplies
- audio amplifier
- white noise generator
- speed beep sound generator
- crash sound generator
- skid sound generator
- motor sound generator
- music input
- yoke polarity driver
Following are brief descriptions of these circuits:
The +15 VDC Power Supply
The first stage of the +15 VDC supply is a full wave rectifier which converts the input 35 VAC (centertapped) to approximately +25 VDC. This later DC voltage is not critical, however, and may vary from transformer to transformer.
The second stage is a self-contained 3-lead regulator chip (LM 340T - VR1) which converts the +25 VDC to +15 VDC. This +15 VDC source feeds most audio circuits, and the base of transistor Q1. This source is a relatively low current supply, so pass transistor Q1 provides a higher current at +15 VDC for the audio amplifier chips (LM 380N or equivalent). Transistor Q1 is configured as an emitter follower, so the emitter voltage will equal the regulated +15 VDC minus approximately .7 VDC (the normal drop across the base-emitter junction for a silicon transistor at or near saturation).
The White Noise Generator
The white noise is produced by the thermal breakdown of a transistor junction. Q2 has a grounded base, an open collector, and an emitter tied to the #15 VDC current source. The base-emitter junction is reverse biased so much that it breaks down, generating broad band noise. U1 amplifies Q2's output. U1's output is a high impedance current source and would be easily loaed down by other audio circuits; the single stage amplifier Q3 prevents this loading, and provides a low impedance source for driving other circuits.
The Speed Beep Sound Generator
U11A is wired as a triggered oscillator (one shot); U11B is wired as a VCO and amplifier, with volume controlled by R39. The processor sends a signal when a speed dot is erased. This pulse triggers U11A, which enables U11B for the one shot period.
The Crash Sound Generator
The crash sound is triggered by a negative-going TTL pulse from the logic boad. Transistor Q6 receives no base current until the incoming signal 5 CRASH forward biases diode CR7, creating a base current path charging capacitor C15. When the input signal is removed, diode CR7 is once more reverse biased, leaving the charged C15 to keep the circuit on for a period determined by the RC combination C15, R24.
This circuit, however, does not oscillate. It merely amplifies the white noise previously generated, and thus is like an amplifying switch with a small turn-off delay. C11, C19 and R11 form a damped-wave decay network. A diode in the collector of Q6 provides output isolation.
The Skid Sound Generator
The skid sound is enabled by a TTL low level input from the logic board. This generator consists of a voltage controlled oscillator (used as a tone generator) and an amplitude modulator used to shape the sound volume.
When there is no input signal, transistor Q11 is saturated, thus holding U4 pin 5 (the input to the VCO) relatively low and U5 pin 2 (the control input to the amplitude modulator) relatively high. This voltage at U5 pin 2 holds the output OFF.
This would immediately rob Q11 of most of its base current and cause the collector voltage to rise, if not for the 6.8 uF capacitor in the upper half of the divider. This capacitor takes time to discharge, and thus the collector voltage rises gradually. This changes the vco frequency gradualy from low to high.
Since the emitter voltage is the amplitude control input to U5, this also enables the output of the modulator U5 in the same manner (except that a descending voltage increases the output amplitude).
The duration of the input signal 5 SKID determines the duration of the skid sound directly. The output is fed directly to the audio input bus.
The Motor Sound Generator
The Q4 ~ U10 curcuit generates the motor sound in much the same way that the Q11 - U4 circuit generates the skid sound. The low motor/high motor input is selected by the position of the control panel FAST button. R52 and R53 control the motor sound frequencies, not the volume. R16 is the volume control. The complements of both the low and high fundamental frequencies are present at the collector of 912. The input U10-5 has the composite of all fundamentals and harmonics.
The Music Input
The music is generated entirely by the microprocessor on the logic board, out of software. The input on the audio board simply consists of an isolation and volume control network, prior to passing the signal to the audio drivers (U7 and U8).
The Yoke Polarity Driver
This circuit is used only in cocktail table models of CRASH, where the video display must be turned over in order for a player on either side of the table to see an upright picture when it is his turn to play. The circuit is a single D type flip-flop driving a transistor (MJE 182). When this transistor is turned on the collector drives toward ground, thus supplying the yoke relay with the ground it needs to energize and reverse the yoke leads in the video monitor.
The flip-flop U2 is set by a negative-going TTL pulse from the logic board to U2 pin 2; this inverts the picture. U2 is reset by a negative-going pulse from the logic board to pin 13.
a .» Diagrams, Pinout Table and Schematics
Switch Inputs UL Data Bus
Audio Outputs Address Bus
c Player re {| siti Car Counter
Screen wadeo
ROM
sync
Timing & Syne Generation Lines
Playfield Maze & Drone Car Images
Figure 8: Logic Board Block Diagram
Figure 9 Audio Board Block Diagram
+15 VDC High Current VCC Sourcefrom Q1
+15 VDC
Regulated
Power Supply| VRI
+15 VDC Low Current
vcc Source
From\ 35 VAC Center-Tapped
XFMR (CT ties to VCC GND)
White Noise
Supply)+5 voc Generator Ul - Q2
5 LOW MOTOR Gnable) Motor Sound 5 HIGH Generator |
Ginabie) MOTOR u10 Crash 5 CRASH y| _Sound Generator > Tone 06 - Generator Amplitude Voltage Modulator |-—2»| Controlled u11 Oscillator u1 Skid 5_SKID Sound Po Gnable) | Generator u2 = v4
Enable Music 5 MUSIC Volume 5 GAME Control R63
Video Inversion Latch & Driver 98 = 7 To video yoke relay U7 Audio Amp1lifier U8 (Used only for audio power amplifier LM 380s)
From
31-3
J1i-4
J1-5
J1-6
J1-7
J1-8
J1-9
53-1
J3-2
J3-7
J5-13
J5-14
35-15
J5-16
J5-20
J5-21
- The static antenna is a six inch long wire in the harness. is connected to J5-13; To
J5-11
J5-8
J5-10
J5-7
55-9
J5-6
J5-4
J5-3
P10-3
J5-1
J5-2
J5-12
Open
Power supply gnd, P7-2
P7-5
P7-6
J6-A
J6-B Pinout Table
Signal
1 player start
Four-way down
Four-way left
Four-way up
Four-way right
FAST
2 player start
Unused
Ground
AC lo used only for 110 VAC aC hi \1amp versions
Video out
Ground
AC gnd
vec 5 VDC
Ground
Coin norm. open
Static antenna*
35 VAC CT grounded
35 VAC
Speaker out
One end the other end is free. as needed, until static discharges no longer turn on the game. From To Signal
5 V out
[5 V common ground
35 V cT
J7-5 35 V lead out J7-6
g9-1 ‘AC interlock out
J9-2 AC common
39-3 IAC ground
g10-1 35 V transformer 110 VAC in J10-2
J15-T 6.3 VAC out 315-2 J
110 VAC hot
P9-1 110 VAC to 5 V power supply
AC common P9-2 AC to 5 V power supply
P9-3 AC ground
P15-1 6.3 VAC supply
P15-2 6.3 VAC common
El AC hot (fused to interlock switch)
Cut 1/4" pieces off
Coin Door Monitor fi a] 1 12] Gorey’? = Geet ia] 73
Er
Main Control
Logic Panel
Board F744
Ho ta} an a1
Power [7 é TT Supply GT | >?
FA Four Js ee Lamp le} 6°) P16
Figure 10: Harness Diagram
W-278 -06 WT
‘Saucn
S|L&I S| 3s Sy ay a ty ve
g ay aaa4 i
sores TLE oo sees te ane om momen scvortey EXIDYINC. chASH LOGIC DIAGRAM | PAGE 30F7 I MAN GENERATION 6R30-3162-A_ |
EXIDY INC. CRASH LOGIC DIAGRAM PAGE 40F7 INPUT / OUTPUT. CR30- 31G2-A
v-27I€-08 97
INA ONISS320%d “WHINSD
240 $ 30¥e WOW D907
“INI AGIKS
V-271€-0C¥7 AMOWAW AINO Gvau £409 30ve | WwuovId 1907 WS WET, “ON AGIXA
sL10805 wamDe oR UL S382500027% >
‘S300 See wae Bb Bb Ly
Ly vel a = ve = = wes] fo , fete an
L Mt
a
i)
rvewo
EXIOV ING. TRASH
LOGIC DIAGRAM
[PAGE 70F 7 CR30- 3162 -A
isa +15 vouts
a Rel 50H 415 vours ue“, 5 ve-ia ase ql +5 vours Ln, Phicsce ae ee vag ag
>
2| veal Ue <j ———— ceerer or nore:
REFERENCE DESIG.
FIRST USED] LAST USED
NOT USED]
a3 tom war C3 qe 8
CRIB
CRESS 3a
wt iz 055,10
R70. Ria, 22,27
Tare VRI
(Baorne CRASH SCHEMATICS
PAGE 1OF2
‘AUDIO (RAO - 8161-5 T=
+15 vours
Ras "eae +15 vours or
Rat hk
SKID ENA
a6 > WHITE NOISE So id no Sage - 2 348 ase 42
bad orig. chase
massa Asa i yi Fox Lee ay
- a
HMB. 7 R
EXIDY INC. CRASH SCHEMATICS
PAGE 20F2 ‘AUDIO L¢k30-3-8_ [es
Exidy CRASH Selectable Options and Audio Adjustments June,
CRASH has three switch selectable options. a seven segment DIP switch located on the main logic board at position 14A (see Figure 2, item 6). This switch is accessible from the front of the game through the coin door. These are controlled by
Following are the options and the switch settings for their selection:
A. Coinage
Player
Player Player
Player Player aN Coin
Coin Coin
Coin Coin
Crashes (Turns)
Crashes
Crashes
Crashes
Crashes
C. TOP THIS SCORE
Credit awarded for topping score
Credit not awarded for topping score switch switch 4 5
ON ON
ON OFF
OFF ON
switch switch
6 7
on ON
on OFF
OFF ON
OFF OFF
switch
OFF
ON 1979
IV. AUDIO ADJUSTMENTS (see -other side)
MOTOR
MUSIC
VOLUME
CRASH
SPEED BEEP
SKID -- 3 pots:
R52=high frequency
R53=low frequency
R16=volume
-- 1 pot:
R63=volume
-- 1 pot:
R66=overall volume
-- 1 pot:
R29=volume
-- 1: pot:
R39=volume
--'2 pots:
R47=frequency
R49=volume
- 1979 EXIDY, 33-6006 Audio Board Adjustments
R52 MOTOR R53 MOTOR R63 MUSIC R66 VOLUME R29 CRASH DIP switch R39 SPEED BEEP R49 SKID R47 SKID 0 R16 MOTOR
Inc.