CATHODE RAY TOMES

Skelagon

SF-X (Nihon Game (Tokyo Nichibutsu license), 1983) · Document · 9 pages · 16 sections · original scan

Page 1

CONVERSION KIT

INSTRUCTION MANUAL

WY Nichibutsu U.S.A. Corp.

Page 2

SKELAGON

| 1 B LICENSE SEAL

2 |

| 4 The license seal can be displayed on the game machine as FIGRE 1. PLACE LISENCE SEAL The license seal must be visible. Use caution so that the seal may | | HERE. not be peeled away thus losing the identity of the P.C. Board. Nichibutsu issues only one license seal for each board sold and no duplicates will ever be made. Put the seal on the back of the little window provided on our marquee or on the back of any clear glass or plastic overlay that you might be using.

FIGURE 1

POWER REQUIREMENTS

The P.C. Board requires a power supply of + 5V 3A (£5%) for game logics

  • 5V 1A (+5%) for game logics +12 V_ 1A (+10%) for audio IC only

CONTROL PANEL SECTION

A 8-way joystick and 2 shoot buttons (left & right) are required. SKELAGON will not work properly with a 4-way joystick.

COIN SELECTOR WIRING

A coin selector switch may be connected to either pin 19 (coin 1) pin 20 (coin 2)

@ N.C.

pin #31

Page 3

LS |

CONNECTOR PLUG

  • Cut the connector-plug as needed, so that it can plug into your game machine connector.
  • Insert the connector-plug into your own game connector, Use a pencil and mark “R”, “L”, “+5” etc. according to signal at the pin on the connector.
  • Connect the connector-plug and 36-pin connector of SKELAGON with wires. (FIGURE 2) Pin Marked “L” will be connected to pin #16 of SCELAGON connector. Pin Marked “R” will be connected to pin #15 of SKELAGON connector etc. (See wiring diagram)

OLD GAME HARNESS

36 PIN CONNECTOR

S — SKELAGON PCB = =

UPPER PCB | ——~came MACHINE LOWER PCB

FIGURE 2

WARNING:

Wiring of the harness that supplies the power (+5V, +12V) of the P.C. Board must be connected as specified, or else, damage may occur. Before plug the P.C.B into the connector, apply power without P.C. Borad and check the voltage of these pins carefully.

Pin # 29, 30,31,32 = GND (OV) Pin # 33, 34,35,36 =+5V Pin #2 =+12V Pin #1 =-5V

Page 4

SKELAGON

| 6 DIP CH SW 1 and SW 2 have been set as shown (FIGURE 3), Please don’t attempt to change these Switch settings.

“AO =

“OOLOOGO6) | =

FIGURE 3

Only SW 3 is used for various optional setting by operator.

sw3 nn Demonstration Sound OFF |ON

4 ON OFF Number of Ships 5 ON ON

FREE OFF OFF

Upright Type ON

Table Type OFF

1 Coin 1 play OFF OFF 2 Coins 1 play ON OFF 1 Coin 2 plays OFF ON 3 Coins 1 pl ON ON ‘ins 1 play

There are three volumes that contro! the sound.

VR 1: Volume of the whole sound

Ovri VR 2: Sound of explosions

O vR4 VR 4: Shooitng Sound, Flying sound, music

VR2 VR3

FIGURE 4

CAUTION: ne pin #3 Two wires from the speaker must be connected to pin #3 and pin #4. pin #4 Both of them are isolated with GND.

a

Page 5

18 BTV MONITOR

Monitor must be placed horizontal and equipped with TTL input level.

19 B THE KITS INCLUDE

A.Technical Instruction 1 pe B. License Sticker 1 pe C. Marquee 1 pe D, Playing Instruction Card 1 pe E.P.C.B. Mounting Z-Bracket 4 pcs F. 36-pin edge connector 1 pe G.Connector-plug 1 pe H.Print Circuit Board 1 pe

110 ff THE SCREEN DISPALY UPSIDE-DOWN OR BACKWARDS

Four wires are attached to the monitor deflection yoke. Two for the horizontal control, and other two for the vertical control. When the picture is upside down, ‘disconnect the two horiziontal wires and swap the connection. When the picture is backwards, disconnect the two veritcal wires and swap the connection. See figure 5a and 5b.

Picture tube

picture tube

deflection yoke coil

deflection yoke coil

4 Horizontal Coil

[ l l 9 Horizontal Coil

2 3

FIGURE 5a FIGURE 5b 3 vertical Coil

Check the voltage of +5V. Adjust from +4.85V to +5.20V if necessary until the background’s stars appear clear and stable,

Page 6

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 7

eee greraten) FERgan ee apiereraty

a Ey hee ay XQ ne etna 3 RAE [

Page 8

TT T7

SKELAGON

@ WIRING DIAGRAM

SOLDERING SIDE PARTS SIDE

—5V12+12V
+ SPEAKER34— SPEAKER
2P SHOOT RIGHT562P SHOOT LEFT
2P LEFT782P RIGHT
1P START9102P START
1P SHOOT LEFT11122P UP
1P SHOOT RIGHT1314SERVICE SW
1P RIGHT15161P LEFT
1P UP17182P DOWN
COIN 119207COIN 2
1P DOWN2122COIN COUNTER

23 24

VIDEO GREEN2526-; BLUE 7
RED2728SYNC
;29307

GND GND 31 32

33 34 +5V +5V 35 36

Page 9

Nichibutsu U.S.A. Corp. 15407 S. Broadway, Gardena, Calif. 90248 Telephone (213) 538-2162 TWX 910-346-6952 NCBTUSA

Printed in Japan