CATHODE RAY TOMES

Prop Cycle

Prop Cycle (World, PR2 Ver.A) (Namco, 1996) · Document · 59 pages · 20 sections · original scan

Page 1

Operators Manual

IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER

SAFETY AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY,

Part No. 90500089

Page 2

© 1996 NAMCO LIMITED. all rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for public or private use, without permission from NAMCO EUROPE LIMITED

While the information contained in this manual is given in good faith and was accurate at the time of publication, NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with European Community directives (1st. January 1996), and as such bears the C € marking. Any changes or modifications to this machine must be in accordance with European Community directives (1st. January 1996).

If you make any unauthorised changes to this product, you may contravene European Community directives (1st. January 1996).

Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains borne transients, some degradation of performance may occur. However the machine will recover normal performance once the source of interference has ceased or been removed. Following abnormally high voltage surges on the mains supply the video monitor may need to be manually reset by turning the machine OFF and back ON.

Published by: NAMCO EUROPE LIMITED Namco House, 8 Acton Park Estate, The Vale, London W3. 7QE

Phone:- 0208-324-6000 Fax:- 0208-324-6010

Page 3

SAFETY WARNING

In order to use this machine safely, be sure to read this Installation and commissioning manual carefully before installation, adjustment or use of this machine. Whenever the owner of this machine entrusts disassembly, installation, adjustment or routine maintenance to another person, the owner should ensure that that person read the appropriate precautions and relevant sections of this manual before starting work. In order that no accidents occur when the machine is in operation, strictly follow the notes on safety described below. Also, carefully read section (X), "Precautions".

Warnings for Operation (C € Requirements)

Va

NOTE:
NOTE:
NOTE:
NOTE:
NOTE: Only operate this machine after checking that it has been installed correctly and in accordance with the Installation and Commissioning Manual. Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There are warning notices to keep hands and feet clear of moving parts, however if the operator feels that a person is in any danger, he should warn that person accordingly. The warning notices must always be kept in good condition and replaced if worn, so that the customer can read them clearly. If there is an error or problem with the machine, operation must be stopped immediately and the problem rectified before any further use. Installation, Service, Adjustments and Routine Maintenance should be carried out by qualified personnel only.

Warnings for Disassembly, Installation, Routine Maintenance and Troubleshooting.

NOTE: ( DANGER:
DANGER:
DANGER:
DANGER: Namco Ltd. bears absolutely no responsibility for accidents, injury or damage resulting from unauthorized changes to this machine. Ensure that the machine has been turned OFF before making adjustments or carrying out maintenance. Also ensure only qualified personnel turn the power ON to this machine. The power supply and inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is the possibility of burns or electric shock. Be careful not to touch these areas. In order to prevent injury due to mis-operation, be sure that the voltage of the main power supply is within the prescribed limits. Also to prevent possible electric shock due to failure, this machine MUST be fitted with a securely connected earthed plug. Do not turn the power switch ON until the machine has been installed correctly.
Page 4

Contents

Operators Manual ... SAFETY WARNING

  • SPECIFICATIONS ..
  • HOWTO PLAY........
  • MAJOR COMPONENTS .
  • INSTALLATION ......... cee 4-1 Fitting the Header Assembly 4-2 Connecting the Cycle Assy to the Monitor Cabinet 4-3 Removing the Shipping Bracket
  • ADJUSTMENTS.. 5-1 Turning on the Power 5-2 Adjustment Switches . 5-3 Test Mode 5-3-1 Coin Options 5-3-2 Game Options 5-3-3 I/O Test..... 5-3-3-1 Switch Test 5-3-3-2 Pedal Test ... 5-3-3-3 Fan Motor Test 5-3-3-4 Lamp Test 5-3-4 Monitor Test. 5-3-5 Sound Test .. 5-3-6 ADS Data. 5-3-7. OTHERS...
  • INITIALIZATION ........ Adjustments When Replacing Parts (Initialization)
  • MAINTENANCE 7-1 Pedal Pressure Adjustment 7-2 Inspecting or Adjusting the Drive Belt 6-2-1 Adjusting the Drive Belt.... 7-3. Removing the Flywheel or Drive Belt . 7-4 Inspecting and Replacing the Pedal Sensor Sticke! 7-5 Replacing the Fluorescent Tube 7-6 Replacing the Fan 7-7 Replacing the Start Switch 7-8 Removing the Handle Covers . 7-9 Replacing the Handle Assembly . 7-10 Replacing the Handle Pots. 7-10-1 Replacing the Up/Down Pot. 7-10-2 Replacing the Left/Right Pot 7-11 Replacing the Pedals 7-12 Replacing the Vibration Proof Rubbers . 7-13 Replacing the Rubber Stoppers
  • PARTS LIST
  • SCHEMATICS ..
Page 5
  • SPECIFICATIONS

POWER SUPPLY:-

MONITOR:-

COIN ACCEPTOR:-

DIMENSIONS:-

Assembled Monitor Cabinet Cycle Assembly Header Assembly

WEIGHT:-

Assembled Monitor Cabinet Cycle Assembly Header Assembly

ACCESSORIES:- Keys:

IEC Mains Lead .... Operators Manual. Installation Manual... Monitor Manual Monitor Remote Control W/Batteries . CashFlow Documents

Joint Bracket - LHS (Cabinet/Bike Assy). Joint Bracket - RHS (Cabinet/Bike Assy) Potentiometer ...

M8x50 Hex Head Set Screw S/Steel .. M8x25 Hex Head Set Screw S/Stee’ M8 Spring Washer S/Steel . M8 Flat Washer S/Steel ...

M5 Security Wrench M4 Security Wrench 230volts AC

Thomson 52” Projector Monitor (RP52)

Mars CashFlow - 1 Channel

1250(w) x 2430(d) x 2320(h) 1250(w) x 645(d) x 1940(h) 980 (w) x 1785(d) x 1380(h) 1145(w) x 350(d) x 380(h)

411kg 200kg 193kg 18kg

(Cash Door) (Coin Door) . (Back Door)

a1

al al

“2d

Page 6
  • HOW TO PLAY

This is a new flight game in which the player gains points by riding a humanpowered propcycle and flying freely in the sky. The player flies the propcycle and gains points by hitting and popping floating red balloons.

  • Operation The game is operated by using the handlebars and pedals.

Handle:

  • Handle Backward
  • Handle Forward Climb : The cycle gains altitude but loses speed. Drop : The cycle loses altitude but gains speed.
  • Handle Left Turn Left.
  • Handle Right Turn Right.

Pedals:

  • The cycle accelerates according to the pedalling speed.
  • The cycle decelerates by pedalling backwards. If the cycle is flown without moving the pedals, the speed drops gradually. If the speed drops below a certain level, the cycle begins to drop rapidly. Speed is lost if the player does not pedal fast enough to gain the desired altitude.
  • Modes There are two modes of play which can be selected at the start of a game.
  • Novice (Point / Speed mode) The level of difficulty is rather easy, so any can enjoy the game. One of three stages is selected at the start of the game, and the objective is to burst as many balloons and score as many points as possible in the allotted time. The player attempts to burst all the balloons for a perfect score in the allotted time to record their name as the best time. There is only one stage play, and continued play is not possible.
  • Advanced Mode (Story mode) The level of difficulty is higher than Novice. The player aims to reach the final destination, “Solitar”, by clearing all three stages in any order they choose. Each time a stage is cleared by reaching the required points total in the given time, play continues into the next stage. If a player fails to clear a stage within the given time the ‘continue’ screen is displayed. Each time the game is continued the required points for clearing a stage is reduced. After all three stages have been cleared, it is possible to challenge for “Solitar”. If the “Solitar” is cleared, it is possible to see the final game ending. It is not possible to continue in the “Solitar”.
Page 7
  • MAJOR COMPONENTS

Sign Assy

Monitor Assy

Handle Assy

PSU Assy Fence Assy

Page 8
  • INSTALLATION

Notes on Installation

DANGER NEVER turn the power to the machine ON until installation has been completed.
DANGER In order to avoid injury or damage to the machine due to misoperation, ensure that the voltage of the mains supply is 230volts AC. Also, in order to prevent possible electric shocks, be sure that the machine is connected to the mains supply with a securely connected earthed plug.
WARNING _ If the location site of this machine has a polished floor it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.
NOTE So that customers are not injured by the movement of the Cycle, ensure that there is at least 500mm separation between other machines or walls.
NOTE In order to gain access to the Power Supply and CPU assemblies] make sure that the rear of the main cabinet is separated from a wall or other machine by at least 500mm.

500mm 500mm

gp 500mm

TITILE: SAFETY ZONE 500mm,

PATHWAY Im

Page 9
WARNING

This machine is designed for indoor use only. The game must_not be installed outdoors or under the following conditions:-

a. In areas directly exposed to sunlight, high humidity, direct water contact, dust, high heat or extreme cold.

b. In locations that would present an obstacle in the case of an emergency, i.e. near fire equipment or emergency exits.

c. Onan unstable or uneven surface, or subject to floor vibration.

4-1 Fitting the Header Assembly

The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.

The fitting position of the Header Assembly is very high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stools etc.)

  • Place the Header Assembly on to the monitor cabinet, connect the connectors and pass the connectors in to the cabinet, locate the blocks on the base of the Header Assembly into the cutouts on top of the Monitor Cabinet.
  • Fit the 2off M8x50 Hex Head Screws, Spring and Flat Washers to retain the Header Assembly to the Monitor Cabinet.

Hex Head Screw (M8x50)

Connectors

Page 10

4-2 Connecting the Cycle Assy to the Monitor Cabinet

1, Connect the connectors between the Cycle Assembly And the Monitor Cabinet.

  • Remove 2off Hex Head Set Screws (M8x25), Spring and Flat Washers on each Joint Bracket, turn the Bracket over and refit, finger tight, using the same screws and washers.
  • Push the Cycle Assembly fully up to the Monitor Cabinet, taking care not to trap any wires.

4 Fit the Joint Brackets, finger tight, to the Monitor Cabinet using 2off Hex Head Set Screws (M8x25), Spring and Flat Washers for each bracket. When all screws have been located, tighten all the screws fully.

Joint Bracket

(M8x25 Screws)

NOTE:- When the machine is fully assembled and in its final position, lower the 8 level adjusters, (4ea on the Monitor cabinet and Cycle Assy), with a spanner so that the machine is level and all castors are raised from the floor by approx. 5mm. Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Cycle Assy Monitor Cabinet

Page 11

4-3 Removing the Shipping Bracket

  • Remove the two Hex Head Set Screws (M8x16) retaining the shipping bracket to the Cycle Base.
  • Remove the two Hex Head Set Screws (M12x20) retaining the shipping bracket to the Cycle Assembly.
  • Remove the shipping bracket. (Ensure that the bracket and the M8 screws and washers are retained safely for refitting if the machine is moved or transported in the future.)
  • Refit the two Hex Head Screws (M12x20) with washers to the Cycle Assembly and tighten fully.

Y

Hex Head Screw (M8x16) ¢ —_—_

Hex Head Screw ew

ES

Page 12
  • ADJUSTMENTS

5-1 Turning on the Power

After the machine has been installed, turn ON the power. The Power switch is located on the rear of the Main cabinet. (See section 3 “Major Components” (page 3).)

5-2 Adjustment Switches

The adjustment switches are located inside the coin door.

1. Service Switch Press this switch to obtain game credits without incrementing the play meters.

Test Switch Slide this switch “ON” to enter test mode. Test mode allows game testing and the changing of game settings. (Refer to section 5-3 “Test Mode” (page 13).)

COIN COUNTER fo}

fe}

LEFT RIGHT PLAYER OO O O

TEST SERVICE TEST SERVICE

Page 13

5-3 Test Mode

  • Open the coin door and slide the test switch “ON”. The “Menu Screen” will be displayed on the monitor.
  • Select the test required by moving the handle bars up or down. The colour of the selected test will change.
  • Enter the selected test by pressing the start button. Select “EXIT” to return to the “Menu Screen”
  • After testing is completed, ensure that the test switch is returned to the “OFF” position to return to game mode.

The Test Switch must always be in the “OFF” position for normal game mode.

XN START : ENTER MENU

COIN OPTIONS

GAME OPTIONS

VO TEST

MONITOR TEST

SOUND TEST

ADS DATA

OTHERS

UP/DOWN : CHOOSE

  • Sets the price of play. (See 5-3-1)
  • Sets the game options. (See 5-3-2)
  • Used for testing the switches and fan. (See 5-3-3)
  • Used for adjusting the monitor. (See 5-3-4)
  • Used for adjusting the speaker volume. (See 5-3-5)
  • Displays the accumulated game data.
  • Used for testing the PC boards and for initializing all of the settings.
Page 14

5-3-1 C oin Options

Select item (1) “COIN OPTIONS” on the menu screen, to set the game cost and related settings.

Move the handle bars up or down to select the required item then press the start button.

Move the handle bars left or right to change the settings then press the start button to store the new values.

Select “EXIT” and press the start button to return to the menu screen.

Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Coin Options on the screen are set as shown in the following table.

(coIN OPTIONS [DEFAULT IN GREEN] )

GAME COST 1 COIN 1 CREDIT ——eicceestetseesfeeeeeeeee (a)

CONTINUE COST PT COIN ——neetttttteteetstsfeeeeeeee (b)

FREE PLAY OFF —aveynesnsntenceana fovea sane (c)

EXIT

\ START: ENTER yy,

ITEM CONTENTS FACTORY SET

  • Game Cost Coins required for one credit - - - - - settable 1-9 1
  • Continue Cost Coins required to continue play - - - settable 1 - 9
  • Free Play No coins required for game - - - - - - On / Off OFF
Page 15

5-3-2 Game Options

a. Select item (2) “GAME OPTIONS” on the menu screen to set the game options.

b. Move the handle bars up or down to select the required item then press the start button.

c. Move the handle bars left or right to change the settings then press t he start button to store the new values.

d. Select “EXIT” and press the start button to return to the menu screen.

EXIT

START : ENTER (Game OPTIONS [DEFAULT IN GREEN]

DIFFICULTY B

CONTINUE TIME B

HI-SCORE INIT NO

SOUND IN ATTRACT ON

/

ITEM CONTENTS FACTORY SET

(a) DifficultyA (easy) to C (hard)B
  • Continue Time | Time allowed to continue new game. A (long) to C (short) B
(c) Hi-Score InitYes/No (If Yes, Hi-Score will be reset when exiting test)NO
(d) Attract SoundSound during standby attract mode Yes/NoYES
Page 16

5-3-3 I/O Test

a. Select item (3) “I/O TEST” on the menu screen.

b. Move the handle bars up or press the start button. down to select the required item then

c. Move the handle bars left or right to change the settings then press the start button to store the new values.

d. Select “EXIT” and press the start button to return to the menu screen

VO TEST >

DIP 12345678 SWITCH PEDAL MOTOR LAMP

EXIT

, START : ENTER UP/DOWN : CHOOSE )

  • Displays the state of the PCB Di number is shown in red. SaSSD GC)

p switches, when a switch is ON the

  • Tests the switches and handle bars. (See 5-3-3-1.)
  • Tests the pedals (See 5-3-3-2.)
  • Tests the fan motor. (See 5-3-3-3.)
  • Tests the start button lamp. (See 5-3-3-4.)
Page 17

5-3-3-1 Switch Test

a. Select “SWITCH” on the menu screen and press the start button. The following screen is displayed.

(v0 TEST

DIP 12345678 SWITCH UP/DOWN : RIGHT / LEFT : START : COIN : SERVICE :

Wo EXIT : PUSH START AND HANDLEBARS up?)

CECI) oO

(a) Handle Bar up/down:

Handle Bar left/right:

Start button

Coin switch

Service When the handle bar is pulled back the value of 0000 will increase and ‘OK’ will appear when the handle bar is fully back.

When the handle bar is pushed forward the value of 0000 will decrease and ‘OK’ will appear when the handle bar is fully forward.

Note: It is normal for 0000 to be changing slightly when the handle bar is in the neutral position.

‘OFF’ will change to ‘ON’ each time the start button is pressed.

‘OFF’ will change to ‘ON’ when the coins to the correct game value have been inserted through the Cashflow acceptor.

‘OFF’ will change to ‘ON each time the service button is pressed.

NOTE: If ‘OK’ does not appear when the handle bars are at there extreme travel, re-initialize the game as described in section 4
Page 18

5-3-3-2 Pedal Test

a. Select “PEDAL” on the menu screen and press the start button. The following screen is displayed.

VO TEST

DIP 12345678 SWITCH PEDAL PEDAL 5/2: ee (a) READY PRESS START SU cecccsssefeccee (b)

TO EXIT : PUSH START AND HANDLEBARS UP.

  • Pedal rotation When the pedals are rotated in the forward direction the value increases, and when they are rotated in the backward direction the value decreases.
  • Rotation sensor check This mode checks whether the sensor is reading the pedal rotation correctly. (see below)

b. When the start button is pressed, the following screen is displayed.

(0 TEST >

DIP 12345678 SWITCH PEDAL PEDAL ACB7 NOW COUNTING PEDAL IT 10 TIMES THEN PRESS START

\_ TO EXIT : PUSH START AND HANDLEBARS UP)

c. When the above screen is displayed, pedal ten full turns in the forward direction. Stop as soon as the pedal has been turned exactly ten times.

d. Press the start button again.

Page 19

e. When the start button has been pressed, the following screen is displayed.

( VO TEST >)

DIP 12345678 SWITCH PEDAL PEDAL C5CF END OK RETRY : PRESS START

TO EXIT : PUSH START AND HANDLEBARS UP Ne 7

If “OK” is displayed the pedals are correct. If “NG” is displayed there has been a problem in reading the pedal rotation. Press start and repeat steps c) and d) again. If “NG” is still displayed after repeating the test, there is the possibility that the sensor board or sensor sticker is faulty.

g. Press the start button while pulling back on the handle bars, to return to the “I/O Test” menu.

5-3-3-3 Fan Motor Test

a. Select “MOTOR?” on the menu screen and press the start button. The following screen is displayed.

( VO TEST

DIP 12345678 SWITCH PEDAL MOTOR FAN MOTOR OFF EXIT

START : ENTER UP/DOWN : CHOOSE

b. When the start button is pressed once, ‘OFF’ changes to ‘ON’ and the fan motor starts and blows air from the front of the cabinet. When the start button is pressed again, ‘ON’ changes to ‘OFF’ and the fan motor stops.

c. Select “EXIT” and press the start button to return to the “I/O Test” screen.

Page 20

5-3-3-4 Lamp Test

a. Select “LAMP” on the menu screen and press the start button. The following screen is displayed.

( VO TEST *)

DIP 12345678 SWITCH PEDAL MOTOR LAMP. BUTTON OFF EXIT

START : ENTER UP/DOWN : CHOOSE Ne S/

b. When the start button is pressed once, ‘OFF’ changes to ‘ON’ and the start button lamp turns ON. When the start button is pressed again, ‘ON’ changes to ‘OFF’ and the start button lamp turns OFF.

c. Select “EXIT” and press the start button to return to the “I/O Test” screen.

5-3-4 Monitor Test

a. Select “MONITOR TEST” on the menu screen and press the start button. The following screen is displayed.

( MONITOR TEST >

GRADATION PATTERN CROSSHATCH PATTERN [CRT] CROSSHATCH PATTERN [PROJECTOR] WHITE WINDOW [H] WHITE WINDOW [M] WHITE WINDOW [L] INTERLACE PATTERN VIEW ANGLE ADJUST [CRT] VIEW ANGLE ADJUST [PROJECTOR] FULL WHITE

EXIT

START : ENTER UP/DOWN : CHOOSE S

b. Select an item with the handle bars and then press the start button. Press the start button to exit a selected pattern.

Page 21

5-3-5 Sound Test

a. Select “SOUND TEST ” on the menu screen and press the start button. The following screen is displayed.

(— SOUND TEST >)

VOLUME RIGHT SP [0-63] LEFT SP [0-63] REQUEST SONG NO. 001 MESSAGE EXIT

START : ENTER / REQUEST / STOP UP /DOWN : CHOOSE LEFT : DECREMENT RIGHT : INCREMENT w,

b. Volume Adjust Move the handle bars up or down to select the item to be changed, and then move the handle bars left or right to change the setting of the selected item. (0 is the quietest / 63 is the loudest.)

c. Sound Output Test Each digit of the REQUEST SONG NO. can be selected by moving the handle bars up or down. Moving the handle bars left or right will change the number. Each number will produce a different sound when the start button is pressed. 001 will produce a stereo test. First a tone will be produced from the left speaker, then from the right speaker and then from both speakers.

d. Select “EXIT” and press the start button to return to the menu screen

5-3-6 ADS Data

Select “ADS DATA ” on the menu screen and press the start button.

The book keeping data for the game will be displayed.

5-3-7. OTHERS

Select “OTHERS” on the menu screen and press the start button.

This screen is used to test the PCB and to reset the game to factory settings.

Page 22
  • INITIALIZATION

Adjustments When Replacing Parts (Initialization)

The following adjustments should always be performed after replacing the game PC board, ROM, Steering Assy, Pedal Assy, or Control Pots. The game will not operate correctly if these adjustments are not made.

  • Ensure that handle bar assembly is in the neutral position by keeping your hands away from the assembly.
  • Slide the test switch “ON” while pressing the service switch. The following screen will be displayed on the monitor.

(— ADJUST MODE >)

BASE BIAS VALUE UP / DOWN ; 0252 0258 0000 RIGHT/ LEFT: 0252 0257 0000

ADJUST HANDLEBARS PRESSING SERVICE SWITCH TO EXIT : TURN OFF TEST SWITCH Ne S

  • Press the service switch to reset all values to 0000 or FFFF
  • Slide the test switch “OFF” to return to normal game mode.
Note: If the above initialization does not perform correctly, repeat two or three times.
Page 23
  • MAINTENANCE

Maintenance and repair should only be carried out by competent persons.

WARNING

(— >)

  • Do not make any alterations to this machine without prior approval. Doing so could cause unforeseeable danger.

2 Only parts specified by Namco Europe Ltd. should be used when replacing or repairing parts (including screws).

: Ensure that power to the machine is turned OFF before commencing any maintenance work (troubleshooting, repairs etc.)

  • If performing work not described in this manual, be sure to contact your distributor for instructions as no responsibility will be accepted for damage or injury.

: Parts of the power supply and projector monitor remain hot and carry high voltage even after switching OFF and could cause burns or electric shock. Take care not to touch these parts accidentally.

  • Make sure that the machine is switched OFF before connecting or disconnecting any plugs or connectors.

7 When removing the mains plug from the wall outlet, always grasp the plug not the cable. Ne wy,

Page 24

7-1 Pedal Pressure Adjustment

This game is designed so that the pedal pressure can be adjusted. This will have an effect on the difficulty of the game. At the time of shipment, the pressure is set to a light setting.

The mechanism becomes uncovered so take care not to trap hands or fingers in the mechanism

  • Remove the four security screws (M5x12) and remove the upper cover.
  • Remove five security screws (M5x20) and four security screws (M5x12) and remove the right side cover.

Security Screw (Mi5x12)

Side cover (R) , Security Screw (M5x20) QS “7—~ security Screw (5x12)

  • To change the pedal pressure, loosen the truss screw (M5x12 Pozi) and move the magnet unit. The pressure becomes less when the magnet unit is moved away from the flywheel, and heavier when it is moved towards the flywheel. Check the pressure by pedalling each time the magnet unit is moved. When the required pressure is achieved, fully re-tighten the truss screw.

Flywheel SU

  • Refit the side and top covers.
Page 25

7-2 Inspecting or Adjusting the Drive Belt

The mechanism becomes uncovered so take care not to trap hands or fingers in the mechanism

  • Remove the three security screws (M5x12) and remove the upper cover.
  • Remove five security screws (M5x20) and four security screws (M5x12) and remove the right side cover.

Push-type scale

  • Press the centre of the belt with a push type scale, or pull the centre of the belt with a spring type scale. The drive belt should have 4 to 5mm slack when a force of 500g is applied. If there is more or less slack, the belt needs adjustment.

6-2-1 Adjusting the Drive Belt

  • Remove the top and right side covers as above.
  • Remove four security screws (M5x12) and remove the left side cover.
  • Slacken the two hexagonal flange nuts (3/8”), one either side, retaining the Flywheel.

Eye bolt (right side, front) Front Eye bolt (Left side, front) =

Flywheel 77 Hexagonal flange nem (8/8 inch) Nylon nut (Mé)

Eye bolt (right side, rear) Eye bolt (left side, rear) Ride Assy (lett side) Ride Assy (right side)

Page 26
  • To increase the tension, slacken the front nylon nuts (M6) and tighten the rear nylon nuts (M6). To decrease the tension, slacken the rear nuts and tighten the front nuts.
Note: To ensure that the flywheel remains parallel within the frame, adjust each nut on both sides by the same amount.
  • After adjustment, turn the pedals three or four times to ensure that the drive belt remains central across all pulleys. If the belt drifts off to one side, the flywheel is not parallel and will need adjustment to one side.
  • When adjustment is complete, tighten fully all nylon nuts and the two hexagonal nuts.
  • Refit the side and top covers.

7-3 Removing the Flywheel or Drive Belt

Remove the top and side covers, (see section 7-2)

Remove the security screw (M5x12) and remove the pedal cover on the right hand side.

Remove the three pozi head screws (M5x12) which fasten the right hand pulley cover. It is not necessary to remove the cover completely.

eAc Pulley cover (R)

a cover

on Screw

IS x 12)

Pozi Head Screw (M5 x 12)

Page 27
  • Remove the four Pozi head screws (M5x12) and remove the wheel cover.

Pozi Head Screw (M5 x 12)

Wheel cover

  • Remove the hexagonal flange nuts (3/8”) on both sides and the four eye bolts which retain the flywheel shaft to the frame assembly.

Flat washer (slitted)

Eye bolt Flywheel Flat washer Plate metal-fitting Nylon nut (M6)

Nylon nut (M6) Hexagonal flange nut (3/8 inch) Eye bolt

  • Move the flywheel forward to release the tension on the drive belt, and slip the drive belt off the pedal pulley.

Drive Belt

Page 28
  • Move the flywheel back to disengage it from the cycle frame.
Note: When disengaging the flywheel, the link unit will come off the shoulder bolt, so hold it by hand.

\\ \ } \ LLL. shoulder bott Link unit

Flywheel

  • Lift the flywheel up a little and remove the drive belt from the flywheel pulley.
  • Remove the flywheel together with the entire link unit by withdrawing the assembly from the right hand side.

Link unit

  • Re-assembly in reverse order.
Note: When re-assembling, fit the flange nuts and nylon nuts finger tight until the drive belt tension has been adjusted. (see section 7-2-1)
Page 29

7-4 Inspecting and Replacing the Pedal Sensor Sticker

Remove the top and left side covers (see section 7-2)

Remove the two Pozi head screws (M5x10) and remove the sensor PCB.

Look through the square cut out and make sure that the sensor sticker is not dirty or damaged.

If the sensor sticker is dirty wipe it with a clean soft, dry cloth. If it is damaged it will need to be replaced.

Sensor sicker

‘Sensor cer

Remove the flywheel (see section 7-3).

Remove one nylon nut (3/8”) and remove the tension pulley.

Note: There is a thick flat washer and an adjustment flat washer on the tension pulley shaft. Take care not to lose them.

Nylon nut (3/8 inch)

Tension pulley

Flat washer (thick)

Peel off the old sensor sticker and replace with Thick side a new one. When replacing the sticker ensure that the sensor sticker is central on the tension pulley. If the sticker is off centre by even 1mm the pedal rotation sensor may not read the sticker properly.

Re-assemble in reverse order.

Note: When re-assembling, fit the flange nuts and nylon nuts finger tight until the drive belt Sensor sticker tension has been adjusted. (see section 7-2-1)
Page 30

7-5 Replacing the Fluorescent Tube

DANGER; _ To prevent electric shock, ensure machine is switched OFF before commencing work.
  • Remove the ten socket button head screws (M5x12), and remove the side vac-forms. (five screws on each vac-form)
  • Remove the two countersunk screws (M5x12) from the bottom of the acrylic.
  • Remove the two socket button head screws (M4x25), and remove the header acrylic retaining bracket.
  • Remove the header acrylic.

Socket Button Head Screw (M4x25)

Header Acrylic Retaining Bracket

Pozi C/Sunk Screw (M5x12) lL

  • Replace the fluorescent tube and/or the starter.
  • Re-assemble in reverse order.
Page 31

7-6 Replacing the Fan

Warning: The Front Base Assembly weighs approx. 25kg. It should be handled by at least two people.
  • Remove the four security screws (M5x30).
  • Disconnect and remove the front base assembly.

——___] Security Screw (M5x30) > <a

Connector

Front-base Assy

  • Remove the four security screws (M5x12) and remove the front cover.

Front cover

Security Screw (M5x12)

Page 32
  • Remove the three countersunk screws (M5) and remove the fan box front panel.

M5 Countersunk Screw

  • Remove the four M4 Whizz nuts on the rear of the front base wood and remove the fan from the front.

FM Whizz Nut

ge © ge ge

Page 33

7-7 Replacing the Start Switch

  • Remove the three security screws (M5x12) and lift up the control panel hood. Remove the switch and lamp assembly from the start button and remove the control panel hood.
  • Replace the switch or lamp.
Note : When replacing the switch ensure that the wires are replaced to the correct terminals.

Startbuten &—— Secuty Screw (usxt2) Bi switch

7-8 Removing the Handle Covers

  • Remove the control panel hood (see section 7-7 above)
  • Remove the five security screws (M5x12) and remove the handle cover (Remove either one of the screws on the bottom of the handle.)

Handle covers

Security Screw (M5x12)

Remove either.

Page 34

7-9 Replacing the Handle Assembly

  • Remove the handle cover. (see section 7-8)
  • Remove the two Pozi head screws (M5x12) with flat and spring washers and remove the control panel base.

Pozi Head Screw (M5x12) (with flat and spring washer) Control-panel base

  • Dis-connect the handle assembly connector.
  • Remove the four Hex head set screws (M8x16) and remove the handle assembly.

Handle Assy Hex Head Set Screw (M8x16) (with flat and spring washer)

Connector

  • Refit in reverse order.
Important: After replacing the handle assembly be sure to re-initialize the machine. (See section 6)
Page 35

7-10 Replacing the Handle Pots.

7-10-1 Replacing the Up/Down Pot

  • Remove the four security screws (M5x12) and remove the front cover

Security screw (M5x12) Sle Front cover

  • Remove the three wires from the pot (note position and colour of wires for re-assembly)
  • Remove the grub screw (M4x8), then slide the pot bracket (A) to the right and pull it forward to remove it.
  • Remove the pot from the bracket and replace with a new one.

Grub screw (M4 x © &

EN oO 6a Flat on the "WEG 1 2 f WP caeromete Pot brack “a7 VE : 3- White/Black or eraes 2-White/Orange Volume terminal 7. Whis/Blue

  • When replacing the pot, ensure that the grub screw engages on the flat of the pot shaft.
Note: After replacing the pot, ensure that the machine is re-initialized (see section 6)
Page 36

7-10-2 Replacing the Left/Right Pot

  • Remove the handle cover. (see section 7-8)
  • Remove the wires from the pot. (note position and colour of wires for re-assembly)
  • Remove the grub screw (M4x8)
  • Remove the pot from the pot bracket (B) and replace with a new one.

Grub screw (M4 x 8)

°3- Whi/Blu Pot terminal.) 2-Whi/Red ri O°

Potentiometer f

Flat on the Pot shaft

Pot bracket (B)

  • When replacing the pot, ensure that the grub screw engages on the flat of the pot shaft.
Note: After replacing the pot, ensure that the machine is re-initialized (see section 6)
Page 37

7-11 Replacing the Pedals

  • Remove the security screw (M5x12) and remove the pedal cover.

Pedal cover | C Security Screw mr! Pe Ne

  • Loosen the nylon nut (M6) on the crank pin ensuring that no threads are protruding through the nut. (If any thread is protruding , the thread may be damaged in the following step).

Pryas

Nylon Nut (M6) Crank pin

  • Turn the pedal so that the nylon nut is at the top. Holding the pedal firmly tap the nut with a hammer to release the crank pin. Once the crank pin has been released the nylon nut can be removed and the crank pin withdrawn.
Page 38
  • When re-fitting, the crank pin should be inserted from the front (monitor side) when the pedal is directly downward.
  • The crank arm moves 2 ~ 3mm in and out on the shaft when the crank pin is inserted. Move the crank arm to the outside and tighten the nylon nut (M6)

Flat washer (Steel)

Nylon nut (M6)

oS Crank pin —’

  • Aluminum washers may accompany the

iS replacing part, but they

are not used.

NOTE: If the nylon nut (M6) is over tightened damage may occur to the crank arm. Tighten only so that there is no play of the crank arm on the shaft. Crank arm —————.,
  • Refit the pedal cover.
Page 39

7-12 Replacing the Vibration Proof Rubbers

  • Remove the two security screws (M5x12) and remove the joint cover.
  • Disconnect the connector and remove the three hex head screws (M12x25).

Hex Head Screw (M12x25)

Security Screw (M5x12)

=

ks c Flange socket (M12 x 25) : onnector —S ——-s Joint cover 9 Hex Head Screw (12x25)

  • Lift the cycle assembly straight up and remove from the base assembly.
NOTE: The cycle assembly weighs approx. 45kg. Ensure that at least two people are used to remove the cycle assembly. When replacing the cycle assembly take care not to trap hands or fingers.
  • Remove the ten security screws (M5x12) and remove the steps.
  • Remove the four pozi head screws (M5x12) and remove the slide and slide base.

Security Screw (M5x12)

Page 40
  • Remove the eight hex head bolts (M10x25) (with spring and flat washers) and remove the joint base.
NOTE: The joint base weighs approx. 20kg so be careful when installing or removing it.

Hexagonal bolt (with flat and spring washer)

Joint base

Front view of the joint base

  • Remove the four hex nuts (M12), spring washers (M12) and flat washers (M12) and remove the joint spacer.
  • Remove the four hex head screws (M10x35) (with flat and spring washers) and remove the cross link.

Hexagonal nut (M12)

Joint spacer en Spring washer (M12)

8 ae Flat washer (M12) Hexagonal bolt

Narrow pillow-type aN ae link

NOTE: The narrow pillow-type unit rotates. When attaching it to the joint base, make sure the installation holes are facing up as shown in the figure above.
Page 41
  • Remove the two hex head bolts M10x25) (with spring and flat washers) and remove the vibration proof rubber.

Hexagonal bolt (with flat and spring washer) a (M10 x 25) ww Vibration-proof rubber

  • Replace the vibration proof rubber and re-assemble in reverse order. When installing the cross link, press the bearing against the positioning plate to position it in the forward and backward direction. To position it in the left to right direction, visually place the cross link so that it is nearly in the centre.

Positioning plate

Bearing

Cross link

Page 42

7-13 Replacing the Rubber Stoppers

  • Remove the joint base as described in section 7-12.
  • Remove the hex nut and spring washer (M8) and remove the rubber stopper.
  • Replace the rubber stopper and re-assemble in reverse order.

Spring washer (M8) > Hexagonal nut (M8)

)

> oN a

r stopper Fubbe Re Joint base

Page 43
  • PARTS LIST

oN

ITEM DESCRIPTION PART No

1| Thomson 52" Projector Monitor84000030

Projector Cabinet Side Decal - LHS 40000341

Projector Cabinet Side Decal - RHS 40000369

Prop Cycle PCB Assy - System S22 XPC-PCB

SMPSU 5v/30A - Astec 301-3400 83000001

5| Elkay Block Sway66000014

Fuse 1%" 2amp Slo-Blo 63500506

°Fuse 1" 3amp Q/B63500544
7|Lamp Driver PCB Assy - Single Channel46000020
9|3.Channel Power Amplifier Assy (vers 2)46000036
10| Schaffner Mains-In Filter Assy66000016
11[Adjustable Foot M16 x 95mm88300079
12| Swivel Castor 75mm59000005
Page 44

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 45

ITEM DESCRIPTION PART No

3Side Cover - LHS45000977
4Side Cover - RHS45000978
5Crossbar Vac-Form45000979
6Handlebar Stem Vac-Form - Front45000980
7Handlebar Stem Vac-Form - Rear45000981
8Pedal Side Vac-Form - LHS45000982
9Pedal Side Vac-Form - RHS45000983

10 | Pedal Cover Vac-Form 45000984.

1Side Indicator Decal40000347

12 | Crossbar Warning Decal 40000348

13| Encoder PCBXPC-Encoder-PCB
14|Pedal- LHSXPC-Pedal-LHS
15|Pedal- RHSXPC-Pedal-RHS
16| Crank Arm - LHSXPC-Crankarm-LHS
17| Crank Arm - RHSXPC-Crankarm-RHS
18| Cotter PinXPC-Cotterpin
19| SeatXPC-Seat
Page 46

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 47

ITEM DESCRIPTION PART No

1| Steering Shaft45000954
2|Handlebars45000955
3|Steering Base45000957

4 | Switch Support Bracket 45000956

5|Handlebar Locating Bracket45000958
6|Handlebar Bearing Block45000959
7|Rosta Spring Support Bracket 'A'45000960

8 | Rosta Spring Support Bracket 'B' 45000961

9|Height Pot Locating Bracket45000962

10 | Steering Pot Locating Bracket 45000963

11.|Hex Spacer45000964
12|Steering Bearing Spacer45000965
13|Bottom Fixing Plate - Steering45000966
14|Steering Housing Vac-Form - LHS45000967
15|Steering Housing Vac-Form - RHS45000968
16|Steering Switch Vac-Form45000969
17|Handlebar Cover Vac-Form45000970
18|Speed Decal40000345

19 | Switch Decal 40000346

20|Movement Stop Bumper45000971
21|Rosta Spring DR-S18x3045000573
22|Rosta Spring DR-S18x5045000574

23 = | Pillow Bearing UCPA205 45000974 24 =| Bearing - Oilite LFF-1615 45000975

25|Handlebar Grip and Plug45000976
26|Rosta Key46000037
27|Handlebar Warning Decal40000371

28 | Start Switch - Red MCPB 60200247

29|Control Pot - 1KX008-023
Page 48

ITEM DESCRIPTION PART No sooreee Bike Mechanical Assembly - Complete XPC-Bike

1FlywheelXPC-Flywheel
2Flywheel Drive PulleyXPC-Flywhidrvpul
3Pulley N168-R03AXPC-Pulley
4Drive WheelXPC-Drivewheel
5Shim WasherXPC-Shim
6Drive Belt N168-RO6XPC-Drivebelt
7Magnet HolderXPC-Magnetholder
22|Pedal Speed Encoder Decal40000344.
Page 49

1 3

A-A section

| 4 in

ITEM DESCRIPTION PART No

1Rear Barrier Perspex39000306
2Perspex Fixing Bracket46000009
3Perspex Fixing Plate46000010
4Rear Safety Barrier Clamp46000014
5Barrier Pipe Joint46000012
6Barrier cushion46000013
7Rear Barrier Pipe46000011
Page 50

24 23

Ls

(Opposite side 30)

;7— 31 (Opposite side 32) 1 — t | 28

7 7 “

20 16 3 17 26 W 12 13 (Opposite side 2) (Opposite side 27)

4 | _—+

21(Opposite side 22)

  • 8 = ll 5 :
  • ‘] \ 36 25 35 38 10 34 7 39 37
Page 51

ITEM DESCRIPTION PART No

1Main Base Metalwork45000985
2Base Step Right45000986
3Base Step Left45000987
4Coin Tower45000988
5Bike Base Surround45000989
6Bike Base45000990
7Bike Mounting Plate45000991
8Bike Rear Base Cover45000992
9Bike Rotational Shaft45000993
10|Bearing Washer45000994
11Floor Mat45000995
12Floor Mat Closing Bracket 'A'45000996
13Floor Mat Closing Bracket 'B'45000997
14Instruction Decal Support Bracket45000998

15 | Cabinet / Base Joint Bracket 45000999 16 | Bike Front Support Bracket 46000000 17 | Bike Angle Support Bracket 46000001 18 | Plastic bike Base Surround 39000305 19 | Nylon Stop Blocks 46000002

20|Cabinet End Base Decal40000349

21/22 | Base Side Decal 40000351 23 ‘| Instruction Decal 40000352

24Instruction Decal Backing46000003
25|"Fork Here" Decal40000072

26 | Cabinet End Warning Decal - Left 40000353 27 =| Cabinet End Warning Decal - Right 40000354

28Rear Warning Decal40000355,

29 | Small Lined Warning Decal - Left 40000356

30| Small Lined Warning Decal - Right40000357
31Angled Warning Decal - Left40000358

32 | Angled Warning Decal - Right 40000359 33 | Base Corner Piece 46000004

34Rubber Stoppers KB-60-58H46000006
35Rubber Stopper RI-3046000007

36 | Adjustable Foot 88300079 37 | Swivel Castor 75mm 59000005 38 | Pillow Bearing UCP 205 46000008 39 | Pillow Bearing UCPA 205 45000974

Page 52

ITEM DESCRIPTION PART No

1Fan Cover Vac-Form45000934
2Fan/Speaker Box Wood37100099

3 | Fan Cover 45000935

4|Top Fan Mesh45000936
5|Bottom Fan Mesh46000042
6Speaker Mesh45000938
7Speaker Mesh Washer45000939
8Fan - Rotary45000940
9|Fan Warning Decal40000343
10|Loudspeaker 5%" Full Range - With Shield62000073
Page 53

Socket Button Head Screw (IVi4x29)

Starter

a Retaining Bracket

04 Fluorescent lamps (3ft)

ar Acrylic

‘Sunk Screw (M5x12) lL

ITEM DESCRIPTION PART No

1Header Wooden Housing37100097
2Fluorescent Tube 3ft98000016
3Header Acrylic Retaining Bracket - Upper46000034
4Header Acrylic30000230
5Header Vac-Form with Inset - RHS45000932
6Header Vac-Form with Inset - LHS45000931
7Header Vac-Form Decal 'NAMCO'40000266
Page 54

ITEM DESCRIPTION PART No

1Sub Bass Cabinet37100100
2Sub Bass Cabinet Grille46000035
3Bass Drive Unit 6%"62000068
Page 55

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 56
  • SCHEMATICS
440 oeFAN/SPEAKER ASSEMBLYjan
—Horaneeiate

PINK : F1GREEN 44

BROWN.oe

3|GREEN/YELLOW atetet

5 RLUEi313

J304 BLACK, {WHITE

eea———
PEDAL|CONTROL

eal[PCB Assy Li [+7 —_ 2le|e _— 33 [a \ 4 [4 [Sia i

———aedJat

1 ji EARTH a3 Oo ~

Tt 2 |e 3/3

J3t Jeg

[77] GREENfrTo}L—

Se YELLOW, 2S 5 GRNZWHT sts = BLACK rae “SpE 5 {5 2 BLUE/WHITE ete 5-| PINK/BLACK rai

5 BLACKale32
“3st AI BLUa135Lit
ip }-WHI/REDio [ioele
TWHIZORG.i [it313
ee EN YELLOWHe He__

3 13 [is

La4 lidf
1S.15 [isi_——
AS]GRN/YEL'id3s

iii

M6 peowN ate

Z ORANGE,S15 St<
=-[GREYj& 16.
74 }RED/BLACK1 J267_[7_| CASHFLOW
== [RED/BLUELL818
—e TEINKZBROWNrs tetSis
> ELLoenree

BLACK 8 4 |4 3 S15 6 [6 717 137 a [8 i [i 3|9 2i[e i 3 [3 4 [4 : 5/5 ' 6 16}

Page 57

3LY iL

ift 2}2

4 [4

T mM 2 GREEN/ YELLOW

i ay] ll

CONTROL PANEL ASSEMBLY aif

SUB BASS S) DECISION SWITCH

J31 | TT | 2/2 —

4/4

[33 e158 vRe 313 HEIGHT

4 [4 NB, 1K ohms

J32 VI i {1 STEERING 3 : N.B. 1K ohms

See 4 es ee ! \ —_ 2 \

Su SERVICE BRACKET T ASHFLOW \ 2 j 3 i 4 4 — | :

8 MARS

E] CASHFLOW

SINGLE CHANNEL

COIN TOWER ASSEMBLY SESE BREE

Page 58

MONITOR

—_eeFA SAO ceay _etllayPSU
iaa

i i i SSR

i HEADER ASSEMBLYiie

| CONTROL PCB mr FLA ae

'ir
iBLUEi |~
chieS

—tete+—ttt ete

reaeiio Tio
!BLUEwel

1 Lg

iivale
ae=Tenet: |!3 [Ss

i aa

i FL es 9/8 Beow ; oO Ue p q 4 sem F224 578 d

ganPca
gqGeNAVEL{
Z5lqu yf 33istep av

ages 3ee3 Rage ad wee al i

—a-

i zn IN + i AUB = L7e ane AUDIO IN +

-a-TEET SPEAKER +

a LEFT SeEAkee {BIGHT SPEAKER + GHT SPEAKER

Biwily. SCART: J9ISUB BASS +
RED1S [is }-450 Ohmfm SCREENED I iSUB BASS —
47Di;~
SeTaz on| AMPLIFIER ASS
‘SYNC26 [2g } 150 OhmLow.eatpial
aiaaa:
!zieESER rmifso Hae
:GHD.1a {ig}itBLUEeye

F AWHITE Lirers

Se"itBLACKae
ra.YELLDWMiracs
; PROJECTORoteecpt

| MONITOR sts

i ae sane — eS — ita

7aata

i ae tints SMPSU. END abs

240v ACa=exp 18
MAINSINTERLOCKete+1ey 10
INPUTi SCHAFFNER MAINS-IN FILTER(INTERLOCK$oxo fi
BROWN,!ee

GRN/YEL FULTER BLUE 1 |

i| ennALL EARTH waReS

; GREEN AVELLOW

I —ee eee—aon
Page 59
PSU/PCB BOARD ASSEMBLY=~~_~_ms

a i

H :PURPLE440.
=| 1CRANGEcy
=PINK.tet
3GREENfa:

4 4

4:BROWN7
oiGREEN/ YELLOW4
eeBLUEfe

fet \

505BLACKislg
ettWETz
2 feEl 9p J28.Tw TWISTED138

a ts 1

rez :RINGING] 1 [1 } YELLOWT
i|RINGIN-[ ®tmirmz
-iRinGouTer |g [3 } BLue _____Lea] |
TAOa 4 | REDidqi

Bus Go LS

—seown __]SpreteS| 1

/Txol 7 [7 i}

/cuola Te;

WHI/RED + ats

PCB!eS

FAN 1 TTT START LARP 2 [2 GRN/WHI aps \ a4 s[s i ! a[s

_ 7!It 1YELLOW

i mee ST.

eeSCREEN, 2ey [ia Dot
iL L7e eeieeeEp a8
Lie estsSTs [aotSED;
caus sa Ta4-4 [aur —zei
7t -ifTTT
EAKER a[ounere
EekeR — Z Zje [2 Hey’a{a

apa BASS [S19 Siete te GREEN e[é

ASSYmp7 pj} Beck:
aotaaoND aei

[cgeen a

72u24Psi6pam
Efi) BenTac atGREEN/ WHITE §

2 [2 [GREEN BLACK

ays | ae= Be eS | BLUE/WHITEeen+
4 SYNcee eg FEIN BL BCSCE werTE
| [3 [vontIPINC/ELACK | S=
6 [6 NE.CNT [By BLACKrRaau

+5 [pe {pa} SED WHITE/BLUE 3 ‘WHITE 7RED by SYSTEM 22 PCB ASSY BITE 7OBAICE | ues spurte zm acic PL

SeeeGREEN/ YELLOWS
edSTEERING Ve_[-@ [@ }—wHiREDFea
Se RenHEIGHT Vela [a WHIZORG)nad
wetLTT geHEWBE

Sv [a [3 een eet

Ser Pe.S{s[ ovanwec heel!
aso ps Lace_i
iNDBLACK616 GND.
FiBLACK2i
ARTear77 GNDSERVICE Sw TT [1 }- Be.
iy pe fe velte onpTest sw[ 2] 2} ORANGEf-
tev [ao io VELLaieata=v
im fag aaconcantee sts} See4
TEE!mee (SS) —eenvak
irv ead RED/ELU.fe
icon sv[a[e PINK/BRN2
i23Cs:
eneee—|

ores. YELLOW OW BLAGK