CATHODE RAY TOMES

Cyberball TM-326 2nd Printing

Cyberball (rev 4) (Atari Games, 1988) · Technical Manual · 64 pages · 64 sections · original scan

Page 1

TM-326

2nd Printi

AvaRt

CY3ER3ALL

Operators Manual

wilawiualrated Parts Liste

(| = ; \\ = = 5" Pp iN Oy hie S We A

. c es Ca 7, Ce ——_ = ee —— =

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

ATARI

GAMES

Cyberball Operators Manual

with Illustrated Parts Lists

Page 4

ii 1988 by Atari Games Corporation. All rights reserved.

No part of this publication any mechanical, phowgraphic or ay be reproduced by clecwonic process, or in the form of a phonographic recording, nor may it be stored in rewieval system, tansmitted, or otherwise copied for public or private use, without permission irom the publisher The game play, all graphic designs, this wehnical manual, its accompanying schenmalic S. Copyright Act of 1976, diagram and the display manuai are protected by the U This Act provides for substantial penalties for violating federal copyright faws. Courts can impound infringing articles while legal action is pending. If infringers are convicted. courts can order destruction of the infringing articles. tn addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to 3250,000 in the case of individuals and up to $500,000 in the case of corporations: Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediateiy hah any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A 9S

Produced by the Atari Games Technical Publications Deparment Technical Writing: Rosalind Hutton Editing and Design: Andrea Dencker Illustration: Mary Ohanessian Sumner Cyberball

Page 5

Cyberbal

| WARNING i Use of non-Atari parts or modifications of | any Atari game circuitry may adversely affect the safety of your game, and may cause in- | | jury to you and your players. |

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: ¢ Substitute non-Atani parts in the game.

  • Modify or alter any circuits in the game by using kits or paris of supplied by Atari Games Corporation

NOTE

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification io this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.

  • The power cord is properly plugged into a grounded three-wire outlet
  • On games provided with an Ficctromagnetic Interference (EMD) ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EML ground cage and that the end board is securely installed with all screws in place and tightened. I you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area
Page 6

Table of Contents

Set-Up How to Use This Manual Inspecting the Game .. Installing the Control Pod Control and Switch Locations Setting the Coin and Game Options Game Phy Maximizing Earnings Self-Test RAM. ROM, and Communications Tests Switch Test. . oS Coin Options Game Options.. Statistics Sereens Histogram Screen. ‘field Scrolling Test Motion Object Alphanumerics Test Color Test... Color Purity Test Convergence ‘Test Sound Test

Maintenance Preventive Maintenance .. Preventive-Maintenance Intervals Opening the Control Panel. Maintaining the Joystick Cleaning the Leaf Switches Cleaning the Coin Mechanisn.... Cleaning the Interior Components Repairs . Disassembling the Joystick Reassembling the Joystick Removing the Vidco Display . Replacing the Video Display... Replacing Static-Sensitive Devices ‘Froubleshooting ROM Problems.

Illustrated Parts Lists

If You Have Sanyo Video Displays. . . Cyberball Statistics Sheet Warranty aa oa be

ede tl >

wily ie Sonn we Cyberball

Page 7

Cyberball

List of Illustrations

Figure 1-1

Figure 2-1 Figure

Figure Figur Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15

Figure 3-1 Figure 3-2

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8

Table 1-1

Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 2-5

Table 3-1 Table 3-2 Control and Switch Locations .......... cones 2 . i-3

RAM or Conimunications Error Me: ROM Error Message Switch Test Screen Coin Options Screen. Game Options Se Seren, 2-5 2-5 ogram Screen..... 25 Playfield Scrolling Test 22-6 Motion Object Test 2-6 Alphanumerics Tesi 24 Color Test 2-6 Color Purity Test 27 Convergence Test 2-7 Sound Test 2-7

Maintaining the Joystick aggre eeeeveenvag ee reeaee ngeesneestare : 33 Removing the Video Display viaccess vnsnrnnsnnd 6

Cabinet-Mounted Assemblies 4-2 Control Panel Assembly .. 4-6 Joystick Assembly ....... 48 Power Supply Assembly. 4-10 Coin Acceptors, Inc. Coin Door Assembly... 4-14 Cyberbail Game PCB Assemb! SAC PCB Assembly .. Filter PCB Assembly .

List of Tables

Game Specifications ......cccceccesccreceteretiteeenieeeseeeee os 1-2

RAM and Communications Error Locations ..... ROM Error Locations Coin Option Settings... Game Option Settings .......... soe Faulty Sound RAM and ROM Loe ‘ations ....

Recommended Preventive-Maintenance Intervals, ROM Functions...

+

Page 8

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found ia this manual whenever they apply

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid elcerical shock. do not plug in the game until it has been inspected and properly grounded. This game should be only be plugged into 2 grounded three-wire outlet. If you. have only a twoawire Oullel, we recommend you hire a licensed electrician 0 install a three-wire grounded out let. If the control panel is not properly greunded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. Aller you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game's power supply can ac cept the AC fine voltage in your location. The line voltage requirements are listed in the first chapter of this manual.

Disconnect Power During Repairs. To avoid electrical shock. disconnect the game from the AC power before removing or repairing any pant of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconaected in the display circuitry and the cathoue-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before: servicing it, Po this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire 10 giound. Then momentarily iuch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again, Use Only Atari Parts. To maintain the sifety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and vour players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shatrered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses myst match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover niust be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on cach printed circuit board (PCB) are properiy plugged in. The conneciors are keyed to fil only one way. If they do not slip on easily, do not force them. If you reverse a connector, il may damage your game and void your warranty Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in counties with 50 Hz line power (used in Furope). If 4 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause 2 poiential fise hazard. Check the product identification label on your machine fo: the line frequency required ABOUT NOTES, CAUTIONS, AND WARNINGS In Mari publications, notes, cuutions and warnings have the following meaning: NOT 4 highlighted piece of information
CAUTION—Equipment andor pans can be damaged or destoyed if instyuctions are not followed You will void the warranty on Atari peinted-circuit boards. parts thergon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING—Plavers and/or technicians can be killed or injured if insieuctions are not followed. Cyberball
Page 9

Set-Up

How to Use This Manual

This manual is written for game operators and service personnel, and provides information for setting up: playing, testing. and tuainiaining your Cyberball™ game. The manual is divided into the following chapters:

  • Chapter 1 contains setup and game play information.
  • Chapter 2 contains self-test procedures.
  • Chapter 3 contains preventive and corrective niaintenance procedures. ¢ Chapter 4 contains illustrated part lists. Wiring and schematic diagrams fos the Cyberball game circuitry are contained in the Schematic Package Sup plement (SP-326), included with your game. This chapter includes information required to set up and play your Cyberball game. Carefully read the information in this chapter before applying power.
Page 10

Serlip

This cabinet should be connected to a grounded threewire oudet only. If you have only wvo-wire oudets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded.

WARNING To avoid electrical shock, plug in the cabinet only after you have inspected it. After inspection, plug it in only to a grounded 3-wire outlet.

Inspecting the Game

Please inspect your Cyberball game carefully to ensure that the game is complete and was delivered to you in good condition. Figure 4-1 shows the locations of the game pa Table 1-1 lists space, power, and environmental requirements, Inspect tie game cabinet as follows: 1. ixamine the exterior of the cabinet for denis, chips. or broken parts

  • Unlock and open the service door. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors ¢on the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation, b. Ensure that all plug-in integrated circuits on each PCB are firmiy plugged into their sockets. c. Inspect the power cord for any cuts cr dents in the insulation, d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounied in place. e. Inspect other major sub-assemblie¢s, such as the video display, prinied-citcuit boards (PCBs), and speaker. Make sure that they are mounted securely and that the ground wires are connected.

Installing the Control Pod

Your Cyberball game is shipped without the control pods assembled on the cabinet to reduce shipping costs and the chance of danuge. To instal) the control pods, do the following

1. Unpack the control pods. Inspect them fur darmage

  • From the sparc parts bag in the coin box. take Gut eeberbail

Table 1-1 Game Specifications

Characteristic Specification

Power Consumption 182 VAC, 280 W RAIS, 45% 1 450°C G37? to +1 Temperature 1) Humidity Not to exceed 95% relative

Line Voltage102 ta 132 VAC CLS. games)|
WidthSi in. 34 em)i
Depth36 in. 5 em.)|

Height 79 in, 208 em) Weight 475 Ibs. (216 kg.)

four large flat washers, four split-lock washers. and four nuts,

  • Open the rear access panel on the cabinet. 4, Put a wooden contro! pod against the cabinet and line up the holes. Push the studs on the control pod through the holes. Push the control panel harness through the center hole. Have someone hold the control pod on the while you reach in through the back of the cabinet and put a fender washer, a split-lock washer, and a nut on each stud. Tighten the nuts with a 7/16-inch wrench. Repeat with the other control pod. uw

Connect the control panel harnesses to the cabinet harness.

  • Reinstall the rear access panel on the cabinet

Control and Switch

Locations

All of the Cyberball controls and switches, except for the on/off switch, are located in the front of the game

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet. (See Figure 4-1.)

Volume Control ‘The volume control is located on the SAC audio board (See Figure 1-1.)

Self-Test Switch The self-test switch is located on the SAC audio board behind the upper coin door on the right. See Chapter 2 for a complete description of the self-test.

Auxiliary Coin Switches

An auxiliary coin switch is located on cach coin mechanism. Use these auxiliary coin switches to give a plav er coin credits

Page 11

Cyheshall

coin soe Counter SAC

Audio Volume

Board U7 Control

Coin Counter The coin counter is located beside the SAC audio board inside the upper coin door on the right. The coin counter records the number of coins deposited

Setting the Coin and Game Options

The Cyberball coin and game options are set in the Self-Test Mode. Refer to Chapter 2 for the recommended settings and the procedure for sciting the options.

Game Play

This section of the manual describes the theme of the Cyberball game and the game play features.

Introduction Welcome to Cyberball, where the players are bigs stronger, and faster, and the action more explosive! The year is 2022. and human football games are histo. ry. The new gane of Cyberball has replaced hunian players with robot players five times their size und an exploding bail, instead of a pigskin Cyber Fas two monitors for two teams and up te four players. Each plaver uses an Swar feast button to call the plays and control the action efor. the action on the field starts, the plaver chooses the plays with the controls. During the play. the joystick conuols the robot's direction en the field. On the olfense, the button conuols the quarterback’ passes and laterals. On the delense, the button gives a defensive player ‘Purbo Defense, & quick burst of speed Cyberball can be played by one to four players: ihe players compete against cach other or Ge compu One player can play against the player, of wo olher players. Two phive loam and | (y against the compuicr, oF Set-Lip

Play Mode

Cyberball rutes are similar to football rules, but players must keep the bail from exploding. if the bali explodes. possession turns over. The ball status dispkay shows whether the bali is cool yarm, hot. or critical A erdical ball will explode if it is not defused. The player can defuse the ball by moving it over the 5Qyard Jine or the goal line: On the line of scrimmage. the robot that the player controls is a slightly different color from the others Each player controls one robot on his team. By p: ing a player button before the ball is hiked, the pliyer can control a different rebot A complete Cyberball game has 6 three-minute periods. Every player buying into the game adds more time for everyone. The more people that play, the more UMe everyone gets per period. Ha game ends in ate. there's a sudden death period to settle the score. The first team to score is declared the winner Auto-Challenge: U one or two players are playing against the computer on one monitor and a new player starts a game on the other monitor, the first players are automatically challenged by the newcomer. The original players can choose to accept or decline the challenge. With the Atari buy-in anytime feature, new players and teammates can enter the action anytime during the game. Player Choices: Players can select offensive and defensive plays, time-outs, and replace weak or demolished players. Cyberball has over 100 offensive and defensive plays: to choose from. The offensive player can choose a running play, option play, pass play, or a time-out. Af ter the player selects the type of play, four patterns appear to choose from. The computer chooses these four patterns based on the current ball status and yards to the defuse fine or to the goal line Meanwhile, the defensive ptayer can choose a short medium, or long defense, The computer also presents four patterns for the player to choose from if tuckdes or exploding shiapnel the player can repkice eyberball robot is damaged during the action by

Which boner jabot bought wal team “funds ded for good performance. H the player doesnt replace the damaged robot. it handles the ball poorly and a le High Score Table: A hugh-score table ranks the per formance of players by the amount of team funds awarded during play. Points scored are converted ta money” and added to the team funds

Maximizing Earnings

Opener options on Cais game ave been kept very simple. You should theroughly read Chapier 2. Sclt-

Page 12

Set-up

Tesi, for information on the Coin Opticns, Game Op: tions, Histogram. and Statistics screens so that you can effectively use the available options. Use the Self-Test sereens showing Statistics and: Histogram to evaluate game data, and the Game Options screen to make ad justments, (Refer also to the Self-Test chaprer for more information on setting options.) The key to maximum carnings is suiking a midpoint on game times. Game times must be short enough so that player turnover is high. Conversely, game times must be long enough to give players a good value and ensure repeat play. (Repeat play is crucial to longevity.) The Cyberball software gives the operator the flexibility to tune game difficulty and enough statistics to intelligently make adjusunents Jf collections seem Jow or are dropping off, check all

1-4 Cyberball

player controls and com mechanisms for proper operation If earnings seem low, the game is technically sound, ge game time per quarter is under 150 seeonds. Choose a slower clock specd seting or liner bar speed sctting on the game option screen, Either change will give players more game time for their money and the aver

Afier changing game option scitings, it is a good idea to reset the game statistics and the histograms. The game statistics can be cleared in the self-test on the second statistics screen by moving the left joystick and pressing any left player button. The histograms can be cleared by moving the left joystick and pressing any left player button while you are on the histogram reen.

Page 13

Chapter 2

Self-Test

The Cyberbail™ game tests asct! and provides visual and audible indications of the condition of the game circuily and controls. Seittest intormauon is displayed on the sereen and through the sound system. No additional equipment is required. We suggest that you perform a self-test when vou fi set up the game, cach time you collect the money. or when you suspect game failure The self-test screens provide information about the game circuits and controls. To go into self-test. turn on the self-test switch iocated on the SAC audio board behind the right coin door. If you turn on the self-test switch, and then turn on the game power, the game performs the RAM, ROM, and communications tests and then the switch test screen appears. If you turn on the self-test switch after the game power has been turned on, the self-test begins with the switch test To leave the self-test, turn off the self-test switch, and then exit the screen by pressing any right player button. To exit the switch test screen, press any left and any right player button together.

Page 14

Self-Test

NOTE You can perform the self-test two ways. It you turn on the self-lest switch first anc then the power switch, the self-test with the RAM, ROM. and Conumunica- Lons tests, If you turn on the power first, then the self-test switch, the self-test begins with the switch test

RAM, ROM, and

Communications Tests

In addition to the usual RAM and ROM tests, a communications test has been added for Cyberball's dual microprocessor which checks the communications between the dual microprocessors, P1 and P2. If the game has an error in RAM, program ROM. or commvunications you will sce information about the error displayed on the screen as shown in Figure 2-1 and 2-2. If the test finds no RAM or communications errors, then after a 30-second delay, the self-test goes to the ROM test without displaying a message. If the game has no ROM errors, then you will not see any message either. If you have an error in any of these tests and you see a message, you can move to the next test by pressing the right player button. If you have a RAM or communications error, check Table 2-1 for the location of the problem. If you have a ROM error, see Table 2-2 for information about the Cyber ball

Figure 2-1 RAM or Communications

Error Message

Table 2-2. ROM Error Locations

Micro- Error Location on Game PCB" ;

processor Address

Pl020000U=1ML=1K/L
pP2000600U=3C/DL=1B
p2020000U=1C/DL=3B

The error is identified as an upper or lower error (U or L) on the

screen, after the word error.

location of the error. If you think you have a ROM er ros, but the screens show no messages, look at Table 3-2 for information about the locations of various ROM functions.

Table 2-1 RAM and Communication Error Locations

Error Message! Display Background Location

P22—-Working RAM BadRed4E, 4F
|Video—Left RAM BadGreenOK. 11K
iVideo—Right RAM BadGreenSK, 10K.
|Color RAM—Left BadBlack21M, 22M
|Color RAM—Right BadBlack25M, 26M
|p22-Common RAM BadBlue4B, 4F

| —Detects Communications Error Purple

|p12Working RAM BadRed
|p—common RAM BadBluc
F2_petecs Communications Error?Purple

1 1 if uco errors are detected, for instance, P2 finds the cammou KAM bad and PI finds @ communications error, then the sercen mety be spit

Pl and P2 are the dual microprocessors > i? or may bare anty one color. However, both messetes will appear. no mater what the display tx heround is

Detects Commronications Error” applies to commaaiications problems other than the common Relat beng bad

Page 15

Cyberhall

960000 . ERROR selfles

Figure 2-2 ROM Error Message

Switch Test

The switch test is shown in Figure 2-3. Use this test to check the convols. As you press the buttons and move the joysticks, the zeros on the screen should change to ones. If they do not, follow the maintenance and repair procedures for the controls in Chapter 3 of this manual. Press any right and any left player button together to move to the next screen.

. on

pRESS

AND MO

6 At APPEAR

0 2 6 g i) 5 a 6 G e)

0 Q BuTTO HUTTONS

PRESS Hi PLAYER BUTTO BS

Figure 2-3 Switch Test Screen

Coin Options

Check and seleet the coin opuons on this screen The screen is shown in F

To move through the coin options. push the felt joystick up or down. You can change the coin option shown in green, The factory delault settings are shown in bluc. To change an option sciting, move the left joystick right or lett Hoyou change an option, but then want to change it back the previous. setting, press cither tel player o

BONUS ADDER ON

PLAYER BUTTO RESTOR A RQ PEA Oo} OSA AND EX!

Figure 2-4 Coin Options Screen button. To save the new settings and exit from the screen, press cither right player button If you want to exit the self-test, torn off the self-test switch, and press any right player button to exit the screen. All your changes are saved and you return to the attract mode.

The coin options are explained below. The settings. with defaults, are shown in Table 2-2

  • Game Price is the number of coins required for one credit.
  • Mudtiplier is the number of coins each coin counts as in the coin mechanisms. For example, if you sclect 2, then each coin counts as two coins.
  • Bonus Adder lets you choose bonus coins, no bonus, or free play. Table 2-3 Coin Option Settings | Option Game Price Settings One coin + ‘Two coins Three coins Four coins, | Multiplier #203 4 5 G@ F 8

| Bonus Adder None # i 2 coins give 1 extra coin | 4 coins give 1 extra coin

4 coins give 2 extra coins

5 coins give 1 extra coin 3 coins give 1 exua coin Free Play (for demonstration mode? | # Manufacturer's recommended settings

Game Options

Check and select the game options on this screen. The sereen is shown in BA

Yo move through the game options. pust the lat jos

Page 16

Self-Test

stick up of down. You can change the coin opucn shown in green. The factory default settings dre shown in blue, To change an option setting, move the left joy sack right or left Ih you change an option seting, but then want to change it back to the previous setting. press cither jet player button, To save the new settings and exit from the screen, press any right player buon. I vou want to exit the selftest. turn off the self-test switch, and press any right player button to exit the sereen. All your changes are saved and you return to the attract mode,

NOTE

Not all of the options are shown when you enter this screen. The word More shows at the top or bottom of the screen to indicate more options. Use the left joystick to scroll through the options.

The game options are explained below. The settings, with defaults, are shown in Table 2-3.

  • Restore Factery’ Options allows you to set all the game options to the factory options by choosing yes. If you want to use your own Settings, be sure to set this to no.
  • Clock Speed sets the amount of time the players receive per play period.
  • Timer Bar Speeds controls the amount of time given on the timer bar shown on the play selection screen.
  • Time-Outs Per Period is the number of time-outs a player is permitted per play period. « Drone Players’ intelligence controls the responsiveness of the defensive players on the field. You can choose average, smart, or very smart. The higher " is 8 on

B

IER BAR SPEEDS

BUTS BER BERIOD 4

SRONE P ENC!

aR CoGe TAG o BuTD HIGH SCORE AABLE Aes

Figure 2-5 Game Options Screen

2-4 Cyberball

the intelligence level, the faster the defense reacts ‘This setting does not affect the length of play time,

  • Clear High Score Table clears the high score table, if it is set to yes.
  • Auto High-Score-Table Reset automaticaly clears the high score table if 2,000 games have been played, and if at least 200 games have been played since the last player entered the high score table

Table 2-4 Game Option Settings Option Settings

Restore Factory OptionsYesNot
Clock SpeedVery slowSlow

“ast Very Fast Timer Bar Speeds slow Very Fast

Time-Outs Per Period1+2
Drone Players’ IntelligenceAverageSmart+

Very Smart

Clear High Score TableNoYes
Auto High-Score-Table ResetNoYes*

+ Manufacturer's recommended settings

Statistics Screens

Use the information shown on the two stalistics screens and on the histogram screen to keep wack of your game use. Record the information on the Cyberbail statistics page in the back of this manual.

The information shown on the two statistics screens (shown in Figure 2-6 and 2-7) is accumulated from the last time the statistics were reset.

At the bottom of the first statistics screen are several times and dates. These are the program version dates If you are having problems with your game, you may need to give Atari Games Customer Service this information.

You can reset the statistics when you are on the second statistics screen by moving the left jovstick and pressing any left player bution

First Statistics Screen The first statistics screen shows the following information

  • Lefi/Right Screen, LefitRight Mech Coins show the number of coins counted in cach of the gaine’s four coin mechanisms.

© fotal Games shows the nurnber of GUL galcs garnets om the frsi played. A unique player sturling to the hast player quitting, segardless

Page 17

Cyberball

ef how many umes the g. how many people pkyed ne Was continued, or

© 0 Phy Minis the number of ninuics the game was idle

eo h234 Ply Mir are the number of minutes the game was pkiyed by one, two, three, or four playcrs. respectively 6 Lrror Count shows the number of errors counted in tic erasable oiemery, He you have a count of more than 75, you should have your game serviecd by a qualified service technician ° Total Credits is calculated by multiplying the coins. by the credit setting you chose in Game Price.

  • Avg Tine Per Credit is the average amount of time in seconds that each credit gave

ERT SCREEN IECH COINS EFT SCREEN, Hi MECH COIS RY SCHEE! CHOOINS e REEN Fi COINS = cal SpiYR An

Figure 2-6 First Statistics Screen

Second Statistics Screen The second statistics screen shows the following statistics both as the amount and as a percentage of the total games played.

  • Comp Games feftis the number of games played by one or evo players on the teft screen against the compute:
  • Comp Gaows Rightis ihe number of games plaved yoga. rave players on the right screen against the compaiter

The rest of che statistics on this serecn are for games: played by players against each other.

  • 7 Period Games is the number of games in which all the players played for oaly one period of the complete six-period Cyberball game 3G Period Games show the number of games in which aii the players played for Wwo ta six peri ods SelfVest
  • 7 Plus Period Games shows the number of games in which all the players played ior seven or more periods. This means that the players completed at least one Cyberball game and started another.
DMPGAMES3&
RERION GA6:
PERIODGAM5
4 SERIOD GAMESfi:
& PERIOD GAM8‘
6 PERIOD GAp:
?PERIODS,

ie OVSTICR AND PR BLAVER BUTTON TO CLEAH STATISTICS BRESS RIGHT D 3 On RSTOGR

Figure 2-7 Second Statistics

Histogram Screen

The histogram screen shows the length of game play and the number of games played. The screen is shown, in Figure 2-8. Write these numbers on the Cyberbail statistics sheet in the back of this manual to assist in maximizing your profit.

BTOGRAN 0} PER CRED!

:

:

"

GAvs5

Figure 2-8 Histogram Screen

Playfield Scrolling Test

You can test the plavfield scrolling circuitry in’ this sereen, Use the left joystick to move tell, right, up, and down, The screen is shown in Figure 2-9 Exit the screen by pressing any right player button

Ww wn

Page 18

SeltTest

Figure 2-9 Playfield Scrolling Test

Motion Object Test

The motion object test screen is shown in Figure 2-10. This tests the movement and color of various game objects. oose a stack with the left player button. Use the left stick to move the stack. Press the left player button to move to the next stack Exit the screen by pressing any right piayer bution

RIG morion cesect vest SCREEN

ar COLOR PALETTE: PRESS: Beare plaver’ ebrren |

Figure 2-10 Motion Object Test

Alphanumerics Test

The alphanumerics test checks the condition of the alphanumerics in the gare. The screen is shown in Figure 2-11

If you see an error on the screen, check the EPROMS ar i5N and 16N Press any right player button to go to the next test.

2-0 Cyberball

BIGHT SCREEN Spzaasarae we + i a2 lad ay aulbiceeneruvesys

PRESS NaBH PLAVER su For SENT bisa Figure 2-11 Alphanumerics Test

Color Test

This test indicates the condition of the teft and right video display color circuits. The screen is shown in Figure 2-12. The left side of both screens should be black and change to grey in the middle. To the right of the grey the screen should appear red, green, blue, and white from top to bottom. If the screen does not fit this description, see the video display manual included with the game for adjustments. Exit the screen by pressing any right player button.

Figure 2-12 Color Test

Color Purity Test

The color purity test has five screens. The first screen is shown in Figure 2-13. These screens show tie condition of the color purity circuit in the video display. Each serecn should display

Page 19

Cyberbath

arectingle of color, with no cunmg atthe corners aid no fines in the disphey blue. white, and gray" Phe screens are red, green

He the sercens are not correct. see the video display manual included with the game for adjustments Exit cach screen by pressing winy right pkiyer button

Figure 2-13 Color Purity Test

Convergence Test

The convergence test is shown in Figure 2-14. This test has three screens. The first is white, the second is puiple, and the last is green. Check the following on the screens

  • The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel
  • The convergence of the lines on the violet and white screens should he within 2.0 mn

raaursuannds unitate cf Eee EH ri ts aon oopsoocgoosS oggnsGesosn UGE SoOSoASO: EERE i nugeengeD by ry ry Ang Agon a REEEEEErt WOGSOGAGI SPCOBRoP OB! OF SS0555! OOCHo ONO aogAgoooeG Age oUooeoe! cet 2D Er ie ago goed! aaougooooeOKG! apo AHOD

EERE ARBOSR ooo eT Ce ECE EE Er alae igngasega: at ae ibecgduggabecger sat ye EEC EEEEEEEE REET Thobbbtieegaaog

Figure 2-14 Conv rgence Test delf-Test

Hi these sercens do not mect these eriteria, see the video displiy manual for suggested adjustments Fsit the screen by pressing any right player button:

Sound Test

Phe sound test indicites the conditian of the music sind sound effects circuils on the SAC (Sampled Audio Cruncher) PCB. CVhis board replaces the Stand-Alone Audio Board ised in previous games.) The sound test screen is shown in Figure 2-15, The sound micropro-

cessor resels ait the beginning of the test. You will hear

the first sound three seconds :tHer the test starts After the microprocessor is resect and vou hear the first sound, the number of game sounds and the sound CPU status information appear tthe CPU is good, the word “Good” appears. WH you get an error message al any point in the seund test. sey Talie 2-4 for more ine formattoi,

‘The test cyeles through the following teste © Music Chip Test © Sampled Audio ‘Test

  • SCOM Reset ‘Test Use the left joystick and the left player buttons to select sounds and listen to them Yo leave the selfrest, switch off the self-test switch, and then press any right player button. You will return to the attract mode.

eo is

Figure 2-15 Sound Test

Page 20

Self-Test Csherball

Error Message

Musi¢ Chip Time Out Sound CPU Interrupt Error Sound CPU RAM 1 Error

Sound CPU ROM 1 Error

Communications Error #1

Communications Error =2

Sound Processor Not Responding, ound RAM and ROM Locations

Cause or Comment Table 2-5 Faulty Location on SAC PCB

aul

2D, 1E, OK

2n

2F U you see this when you enter the sound test, the sound processor Cannot proceed any further. Press any right player button to exit the test 1D Counts the number of errors caused by the SAC PCB or Game PCB. TI

means that the SCOM chip (part no. 137526-001) on one of these boards is

bad

i CAUTION

lle it ig | The SCOM chip is a CMOS IC and is static sensitive. If you do not ha | properly. you can permanently damage this chip. See the section Repla Static-Sensitire Devices, in Chapter 3 of this manual, for more information.

Probably the > PCB is disconnected from the Game PCB, or the chip at 1D is not inserted into its socket.

jor problem with the SAC PCB. If you cannot enter the self-test. the ness may be disconnected between the PCB and the Game PCB.

Page 21

Chapter 3

Maintenance

This chapter includes prevenuve maintenance and repair procedures for the Cyberball™ game componenis that are subject to the most use. To make sure you have maximum touble-lree operation from thi perform the preventive maintenance described i chapter at the intervals recommended. Removal, disassembly, re-assembly, and replacement procedures are provided for components that might need to be repaired. If a part is mentioned, but not it lustrated, check in Chapter 4, [Hustrated Parts Lists, to locate the part.

Page 22

Maintenance Cyberbalt

Preventive Maintenance

Preventive maimtenance includes cleaning, bubricating, and tightening adware, How often vou perfor pre ventive maintenance depends upon the game caviron ment and frequency of pki. However. you should reg ularly maintain the components lisied in Table 2-1 Recommended Preventive-Mainienance Intervals

" WARNING. To avoid possible electrical shock, turn off the game before performing any maintenan€e procedures.

Preventive-Maintenance Intervals

For the best performance from your Cyberball game. perform the maintenance in Table 3-1 at the intervals specified

Opening the Control Panel

  • Turn off the power to the game.
  • Unscrew the two tamperproo! screws on either side of the control panel
NOTE A hole is provided inside the upper coin door to store the tamperproof key wrench when it is not in use
  • Pull the contol pane! up and disconnect the harness connector,

9 replace the control panel, first fit the front edge into the slot in the cabinet. Reconnect the harness connector, Now fit the contro] pancl in place and yeinstall the tamperproof screws and flat washers.

Maintaining the Joystick

Maintain the joystick by inspecting the pivot hall, actuator half-ball, and the shaft and hubricating che joystick with lithium grease,

  • Turn off the power to the game
  • Open the contro} panel and disconnect the harness: connector.
  • Remove the joystick from the control panel. Use « 3/S-inch wrench to remove the nuts and washers that hold the joystick on the control pane!

we w Table 3- Maintenance Intervals

| Joystick Lubneate and mspect every three months. | Leaf switeh Clean every 3 months. H | Coin Mechanism Inspect whenever you collect coins. Clean every three | months, |

t. Remove the four long screws that hold the jo together. See Figure 3-1 actuator, and the Take off the 8-position plate, the lower housing

  • Check the actuator ha shaft for dirt and wear {-ball. the pivet ball, and the

te the actuator half-ball on the end of the shaft, the pivot ball below the upper housing. and the spring inside the upper housing, Use lithium grease,

  • Put the joystick assembly back together. Fit the pin in the pivot ball into the slot in the lower housing.
  • Replace the long screws and tight them. Do not over-lighten the screws. The joystick handle must return to center easily.
NOTE

Do not tighten the long screws too much. If you do, the handle will be difficult to move and players may become frustrated with the game.

  • Replace the joystick assembly on the control panel
  • Use the Self-Test to make sure you have reussembled the joystick correctly

Cleaning the Leaf Switches

Your game may have citlici snup-action switches or leaf switches. The snap-action switches maintenance. The leaf switches should t ughtened as follows: quire po < Cleaned and

  • Remove the contol pancl
  • Use electrical contact cleaner to clean the contacts Do not burnish the conntets, The wij the cross-bar contacts of the Jeal se cleaning action sing action of his a self
Page 23

Cyberbail

041287-01 Lower Housing

160044-001 Srap-Action Switch

039714-01 Actuator

039717-03 8-Position Plate A040932-01 Upper Housing Assy | = / / / !

176030-110 #4-20 Screw

044390-01 Lithium: Grease Cushion Ring

039716-01 Joystick Pivot Ball

040693-01 | 1760018-003 Joystick Actuator Ball #8-16 Screw

Figure 3-1 Maintaining the Joystick I | A Grease Maintenance

040304-01 Ball-Shaped Handle and Shatt a

039713-01 Joystick Disc

041512-01 Progressive Plunger Spring

039712-01 Joystick Piunger

939722-01 Upper Joystick Housing

73-20824 | Large Roll Pin

a

[> _ 73-20509 ‘Small Roll Pin

a Lithiuin Grease

Page 24

Maintenance

  • Tighten the stumped nut holding the leat switches on the control panel using a 5.8-inch wrench. It vou need to repkice a switch bution, take off the stamped nut with a wrench while firmly holdiag the bezel on the outside of the control pane!

Cleaning the Coin

Mechanism

Use a solt-bristied brush to remove loose dust or forgo material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air,

Cleaning the Interior Components

WARNING Turn off the game power but leave the power cord plugged in while you clean the inside of the cabinet. The power cord provides a ground path for stray static vollages that can be present on the cleaning tools.

Perform the following procedure to clean the components inside the cabinet.

  • Turn the game power off and wait two minutes. Leave the power cord plugged in.
  • Remove the rear access door. Cyberball
WARNING The video display contains lethal high voitages. To avoid injury. do not attemp! fo service this display until you cbserve all precautions necessary for working on high-voltage equipment.

Discharge the high voltage from the cathode-ray tube (CRT) before proceeding. ‘he display assembly contains a circuit for discharging the high volt age to ground when power is removed. |lowever, to make certain, always discharge the display as follows: Attach a length of solid gauge wire to the blade of a well-insulated screw driver. . Attach the other end of the wire to an earth ground. Quickly touch the blade of the screwdriver to the CRY anode by sliding it under the anode cap. o

d, Wait pvo minutes and repeat step c.

CAUTION Be very careful when you clean the electricai components in the cabinet. Do not touch the electrical components with any object other than the so/t bristles of the vacuum attachment or paint brush.

. Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to thoroughly clean the electrical components (power supplies, PCB assemblies, display, etc.) ad

Page 25

Cyherball Maintenance

Repairs

Repairs include the removal, disassembly. re-assembiy, and replacement of game components. ‘rhe following procedures are provided for components that may require repairs.

Disassembling the Joystick

Perform the following procedure to disassemble the joystick (see Figure 3-1).

  • Take off the control panel and disconnect the harness Connectors. iy Remove the joystick from the contrel panel. Use a 3/8-inch wrench to remove the four iocknuts and washers holding the joystick onto the control panel,
  • Remove the four screws holding the 8-position plate on the bottom of the assembly
  • Remove the white plastic actuator and the lower housing that the four switches are attached to.
  • Remove the small roll pin holding the actuator halfball on the bottom of the shaft by pushing the roll pin all the way through the shaft. Slide the actuator half-ball off the end of the shaft
  • Remove the large roll pin holding the large pivot ball on the shaft below the upper housing. Push the pin through the ball and the shaft. The pin will not be easy to remove because of the pressure on the pivot ball from the spring above it. After you push the pin all the way through the ball, slide the pivot ball off the shaft.
  • Slide the upper housing off the shaft
  • Slide the plunger and the spring off the shafi.
  • Slide the dise off the shaft

Reassembling the Joystick

J. instal! the disc on the shaft.

  • Slide the spring on the shaft. Push the large end of plunger onto the shaft and over pan of the spring (see Figure 3-2).

“NOTE Lubricate the plunger, ball, and housing at this point in the reassembly procedure.

  • Slide the upper housing onto the shaft Before you put the pivot bail on the shaft, insert the large roll pin pavtw into the pivot ball. The roll pin should not interfere with sliding the pivot bal} onto the shaft. Slide the ball onto the shaft, and line up the roll pin with the hole in the shaft Now push the pin through the shaft You will have to hold the pivot ball against the pressure of the spring. Make sure the ends of the soll pin extend out the same amount on both sides.
  • Pui the small roll pin part way into the actuator ball and slide the ball onto the shaft. Line up the roll pin with the shaft hole. Push the roll pin through the ball and the shaft.
  • Fit the lower housing over the shaft so that the ends of the large roll pin fit into the slots on the inside of the housing. Turn the lower housing so that screw casings align with the holes in the upper housing.
  • Put on the white plastic actuator so that the black cushion ring is opposite the switches.
  • Now install the 8-position plate below the actuaior so thai you can reinsert the long screws:
  • Put the long Phillips head screws through the 8-position plate and up through the housings. Do not over-tighten the screws, of the joystick will be too hard to move.
NOTE

The joystick handie must return freely to the center position. If it does not, players will become frustrated with the game.

  • Reinstall the joystick on the conuol panel

Removing the Video Display

Perform the following procedure to remove the video display. (See Figure 3-2.)

WARNING Be very careful when you rernove the display from the cabinet. Do not drop it! You should weigh at least 150 pounds to remove the display by yourself. You should also wear gloves sc you do not cut your hands on the sheet-metal edges.

1, Turn the game power off and wait two minutes Leave the power cord plugged in

  • Remove the rear service door.
Page 26

Maintenance

"WARNING © High Voltage The video display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation. never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or drapped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display.

  • Be sure that the game power is turned off before discharging the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a. Adach a length of solid gauge wire to a well-insulated screwdriver, b. Attach the other end of the wire to an earth ground. Cyherbatt

&. Quickly touch the blade of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait two minutes and repent step ¢

  • Disconnect the display harness connectors from the isplay vt ke off the retamer holding the top of the display shield, Remove the shield
  • Remove the bezel carefully from the cabinet. the bezel is held in place with double-sided tape.

8 Remove the wo wood cleais on the left and right sides of the cabinet. Use a Phillips screwdriver to remove the two screws on each side

  • Use a 3/s-inch nut driver or socket to reniove the four lock nuts and washers holding the display onto the metal mounting brackets in the cabinet
  • Carefully lift the display out through the front of the cabinet. 11, Replace the video display as described in the following procedure.

Replacing the Video Display

Perform the following procedure to replace the video display in the cabinet. (See Figure 3-2.

Video

Bezel Display

| Lecknut

Cleat with Screws

Page 27

Cyberball

NOTE If you repiace the cathode-ray tube and yoke together, adjust the brightness, size, and centering as described in te display service manuai. Check the purity and convergence according to the display service manuai insiructions, but do not adjust these two unless it is required.
  • Position the display so that the four holes in the video display mounting brackets align with the four threaded studs in the metal brackets,
  • Install the four iarge washers and locknuts on the display frame and mounting brackets. Use a 3/8-inch nut driver to tighten the lecknuts, Be sure that the display is centered horizontally
  • Connect the display harnesses to the display
  • Install the two cleats that support the bezel and the display shield 7, Replace the bezel and display shield. Reinstall the top retainer

Replacing Static-Sensitive

Devices

Be careful when you are working with static-sensitive devices on the game PC boards. Static charge that has buili up in your body can cause st static-scnsnive de vice to fail, Leakage from an improperly grounded soldering iron can also cause a stitic-ssensitive device to fail Before you replace a static-sensitive device, make sure it rs actually defective. A static-sensitive device can appear defective due to leakage on 3 PC board. To mak sure a device is defective, ground any static voltages Clean both sides of the PC board with flux remover or an cra Pfs, clean thoroughly beaveen the gate, drain. and source leads. Then test the device. er, For discrete F

If you replace a static-sensitive device, be careful when you handle the new static-sensitive device. The device may be packaged in conductive foam or may ha 1 protective shorting wire attached to the pins: Remove the conductive foam just pricr to inserting the device into its socket or soldering to a PC board. Remove the shorting wire only affer the device is inserted into iis socket or a/ier ali che leads are soldered in place.

Troubleshooting ROM Problems

Use Table 3-2 to find the location of ROM problems in your Cyberbail game.

Table 3-2) ROM Functions

Problem Type of ROM Location — |

Score box disappears Letters and numbeis disappear Play diagrams disappear. Vertical lines appear over the entire s Alphanumeric 15N or 16N) |

Totally black screen | Both Alphanumeric ROMS NOYE: Check video display before repkicing ROMs 15N and 16N

Playfield has several rows of short vertical lines across it

HSL/M. OL: Mi

Playfield, Mor HM |

Linebackes, running back, or quaterback are breaking up

Quarierback or cornerback are breaking up.

inemen, receiver, or Sifely are breaking up.

Sidelines, ball, receiver marks, or tight end are breaking up. FAC Motion Object | | 15/16a, of 15/160. |

f412A. 12C,|

PY6/17A, or WG/1FC |

{|BAL 13C.|
tISA, oF LSC{

!

|WA,MC.i

| 19, or 19¢

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

Chapter 4

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Commen hardware parts, such as screws, nuts, and washers are usually net listed in the parts lists. The parts lists (except for the PCB paits lists) are artanged alphanumerically by Atari part number. All Aprefix numbers, which are assemblies, come first. Next are part numbers with six numbers followed by a hyphen (000598- through 201000-). Ending the list are past numbers with a two-number designation followed by a hyphen (00- through 99-) The PCB parts lists are arranged in alphabetical order by component. Within each component list the parts are arranged numerically by part number. When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games Atari Games Customer Service phone numle front cover of

Page 30

Mlustrated Pants Lists

036158-01 Light Box Stree (045159-01 Auraction De 046183-01 f Bezel 178056-002 1W2-Inch Foam Tape 046 163-01 Display | 75.0308 Shield {#10 Flat Washer 177010-246 #10-26 Lock Nut 036161-01 Light Box R 76013- 170003-001 Fluorescent Light / } 171086-001 Lamp | Fixture / / 040936-11 Light Box 045166-01 Shield Grille

Molding Cyberball

148607-104 Speaker / /

178201-03 Chrome T-Molding

139017-305 Video Display

046162-01 Retainer 78-6900401 A046154-01 Black Foam Tape 040936-10 Control H © © © 176013-212

DisplayPanel AssylSquare-Drive Screw
Shield75-0458i
MoldinA045183-0141/4 Split-Locki
oreingWoodenWasherile
Contro! Pod~——75-07002i:
#1/4 Flat‘|--—7
WasherH=Es

75-9158 a8 #1/4-20 Hex Nut \'Ni ge

17834-024 T-Molding oe")

Gideon 171078-002 a7 038091-01 Coin Counter fastruction 171027-001 Ciena Parsi Decal Coin Door

Figure 4-1 Cabinet-Mounted Assemblies, Front View A046150-01 B

Page 31

Cyherball

| Not Shown 046164-01 Top Right Deca A045576-01 A046209-01 Com/Aud Harness Ground Strap Assy ! Assy 046160-01 7 fapiso2 046201-01 Mirror | Top Lett Decal Main Harness Assy oagigao1 | \ A046202-01 Left Coin Decal 046165-02 Video Harness 046184-02 Right Decal Assy Right Coin Decal 8046203-01 141026-002 Video Power Ferrite Bead Shield Harness Assy 173%26-00% A046204-01 Tamper-Proof Oriver Speaker Harness Key Assy 99-11006 ‘8046205-01 AC Harness Assy Lame anne ‘A046208-01 PCB Power A044963-21 Harness Assy SAC PCB Assy ——_—_—__! 034536-14 Foam Damper

A046218-01 Rear Access Panel

A045186-01 Control Pod Assy

046165-01 Left Decal

/ SI

/ / 046211-01 \ y028-001 U Power Suppi 4044283-21 ‘ 043055-01 nosy GanePCBAtsy Caster Ono Ha s A045191-01 \ 034536-14 Ssy Filter PCB Ass am Damper ry 78-3201 Foam Damper Glide

Figure 4-1 Cabinet-Mounted Assemblies, Rear View A046150-01 B

Page 32

Miusu.ited Pans Lists Cyberball

Cabinet-Mounted Assemblies Parts List

Part No. Description

AWG 3059-0] On Of Harness Assembly AOwi Cyberhail Game Assembly (see Figure 4-01 AOI4904-21 SAC Audio PCB Assembly (see Figure: AQUSISS-01 Wooden Control Panel Pod

AQH5180-0) Control Panel Pod Assembly Unchudes wood pod (part no. AQ45 1830-01) and ihe Control Panel Assembly shown in Figure 1-2.) Filter PCB A: Figure 4-8) Com/Aud Harness Assembly A0AG1S4-01 Control Panel Assembly (see Figure 4-2)

A046201-0! Main Harness A: A046202-01 Video Harn A046203-01 Video Power Harness Assembly A046204-01 Speaker Harness Asse

AC Harness Assembly Al 8-01 PCB Power Harness Assembly 4046209-01 Ground Strap Assembly A046211-01 Power Supply Assembly (see Figure 4-4)

A046218-01 Rear Access Panel O44536-14 Foam Vibration Damper 038091-01 Cash Box 040936-10 Display Shield Molding

040936-11 Light Box Shield Molding Instruction Panel Decal Light Box Shield 046159-01 Light Box Attraction Decal

046160-01 Mirror 046161-01 Light Box Shield Retainer 046 162-01 Display Shicid Retainer 046163-01 Display Shield

056164-01 Top Left Decal 040164-02 ‘Top Right Decal 046165-01 Left Side De: 046165-02 Right Side Decal

046160-01 Speaker Grille G46 183-01 Display Bezel OFO1 3-08 Tech O4G184-02 Right Coir

149017-395, 19-Inch Coler Stundard-Resolutien Prismatic Video Display (Model 19K 7601) Ferrite Bead Shield Inch Shielded Speaker owivel Caster 17025-Uul

17834024 Black T-Molding 170003-001 1Sinch, 15 Watt Fluorese 1 Coin Acceptors, Ine. Coin Door Assembly (sew Figuie 43 78-002 Xon-R ¢ Coin Counter

Page 33

Cybetball

Part No.

ITSN5O- COL

126-002 201-03 1308,

78-G900401

99-1106 Cabinct-Mounted Assemblies Parts List, Continued

Description

IS-Inch Fluorescent Lamp Fiatuae cquase Dave Serew Polymer Locknui 1 2Inch oan: Tape

Tamper Proot Hex Driver Key

Chrome T-Molding

= 10 Phat Wide Washer =1 4 Split-Lock Washer

ela Flat Wide Washer = 14-20 Hex Nat Adiustable Glide 1 -tInch Black Foam ‘tape

Fluorescent Lamp Retaining Clip

These are the technical information sitpplements tu the game. Cyberball Schematic Pack Cyberball Self-Test Label Iustrtted Paty Lists

19-Inch Color Stundard-Resoltition Prismatic Video Display Service Manu Cyberbail Operator's Manual

Page 34

Tlastrated Parts Lists Cyberbull

Not Shown: A046206-0% Control Haress Assy

75-5112 3#t-Inch-Long Carnage Bolt / i

086156-01 Control Panel Deca!

160013-001$ Cross-Bar Leaf Switch with Button Holder 046155-04 178030-003$ LiS1S5-0% s7@oan-0013 8% Buton Asiy / Wnt Button Assy

Ss 75-991 0NO Stamped Net 78-6900401 / "a 177010-240 Ta Foam Tape Lock Nut 8-Position Joystick Assy See Figure 43 4All parts marked with a double dagger are the alternate choices. You shouid substitute them with the following three primary-choice parts: 160044-001, Snap-Action Switch 178237-003, Black Button Assembly 178237-004, White Button Assembly

Figure 4-2 Control Panel Assembly A046154-01 A

Control Panel Assembly Parts List

Part No. Description

A040933-03 Joystick Assembly (sce Figure 4-3) A046206-01 Contro] Harness Assembly 046155-01 Contol 046 156-01 Control P:

160044-004

177040-240, 178237-003,

S128 F8-0900401

4-0 Shap-Action Swich (Acceptable substitutes are part ne. 160013-001, leaf switch with buden holder, with part no, 75-9910N0, stamped nut) 10-24 Polymer Locknut Black Button: Acsembly (Acceptable substitute is part. no. 178030-003.)

While Button As embly (Accepable substitute is part no. (78030-0011)

Black Ganage Bolt Black Foum Tape

Page 35

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 36

Wustrated Parts Lists

4040932-01 Upper Housing Assy

041287-01 Lower Housing

Snap-Action i ‘Swich * 176030-110 #4-20 Screw

048390-01 Cushion Ring

039714-01 Actuator

a J 039717-03 8-Position Piate Va 4760018-003 #8-16 Screw ~<

Lo coystick Pivot Ball

soystiok Actuator Ball Lithium Grease

Lithium Grease '

039716-01

040893-01

Figure 4-3 Joystick Assembly A040933-03 E cyberball

040304-01 Bali‘Shaped Handle and Shait

039713-01 Joystick Disc

041512.01 Progressive Plunger Spring

039712-01 Joystick Plunger

039722-01 Upper Joystick Housing

73-20824 Large Roll in

73-20509 Small Roll Pin

A nium Grease

Page 37

Cyberbalt

Joystick Assembly Parts List

0397 16-01 039 3, 039 61 940304-01

040693-0% 041287-01 043696-01 044390-01

107027-001 160044-001 1760018-003 176030-110

73-20509 73-20824 Upper Housing Assembly Plunger Dise Actuator

Pivot Ball 8-Posilion Plate Upper Housing Ball-Shaped Handle and Shaft

Actuator Ball Lower Housing Pregressive Plunger Spring Cushion Ring

Lithium Grease Snap Action Switch 16 Phillips Head Screw 4-20 Hex Washer Head Screw uo

Small Roll Pin Large Roll Pin Mlaytrated Parts Lists

Page 38

cyberball Mlustrated Parts Lists, cy

4046243-01 Aoagae7-03 °° Bk PS pr 6" Wh Jpr Assy, SASSY

2-Pos Term Block \ 8° Blk Jpr Assy Assy

149006-001 5V, 134 Hitron Switching P'S. A046207-01 +5V Harness: be Assy

a A042384-01 Line Fiter Assy

146098-3022 a 3 Amp Siow Blow a) Fuse ; \ A043367-01 | | ° \ Jpr Assy ~ X rae \ 146008-2022 \ cul \ 2 Amp Slow Blow \ See 142045-001 Fuse \ Transformer 179228-2205 \ 5-Pos Fuse Block 142047-001 034544-01 nsk Fuse Block Cover Transionmer (Not Snown)

Figure 4-4 Power Supply Assembly A046211-01 A

Page 39

Cyberall Mlustiated Parts Lists

Power Supply Assembly Parts List

Part No. Description

AQ 238 Uy Line Filter Assembly \UH S307 OF jumper Assembly AQ S307 02 o-fnch Black Jumper Assembly MO 13 807-03 O-loch White Jumper Assembly

AU 0207-0} +5V TLimess Assembly MOM SO Inch Black Power Supply jumper Assembly WAG S-OL Minch White Power Supply Jumper Assembly O4454 01 Fuse Block Cover

i2045-u0 Vransformer 142047-001 transformer 149006-0001 SV. ISA Hitton Switching Power Supply 179225-2208 S-Positvion Fuse Block

179231-002 2-Position Terminal Block

14G008-20222 Amp.230V Slow Blow Fuse

£49008-3022 mp. 250V Slow Blow Fuse

Hitron 5 Volt, 13 Amp Power Supply Sub-Assembly Parts List

Designator Description

Capacitors or, Metal Film, 0,047 iF, 250 V 99-211036 . Metal Film, 0.1 pF, 400 V 99-211038 Capacitor, Ceramic, 4700 pF, 400 V 99-211049 Capacitor, Electrolytic, 100 pF, 200 V 99-21 1046

omgCapacitor, Metal ¥ilm, 0.1 2. 400 V9.211038
csCapacitor,Ceramic, 0.001 pF, 2 kV9-2 042
coCapacitor, Ceramic, 0.01 PT KV, 75099-21 1041
ueCapacitor, Electrolytic, 220 tfOULU
iW‘Mettl Filin, 0.22yh140 Vws
enCapsMetal ily. 0.022 nk, 1a0yOT) Es
oaCapacihPim, 22 ph me \ou Z1Mt
t1certPsa VE 2 RW) ZANim F.

» BeGFOIy Te, 20 WH LON

‘cereSUPE LRN. ZSP
potiAi etTON

Diodes

Page 40

Mlustratod Parts Lists

Hitron 5V, 13A Power Supply Assembly Parts List, Continued Cyberball

Designator Description Part No.

Du. D2 Diode, Schottky. S10SCiM DI3-D16 Diode, Rectifier, IN4006 2D1 Diode, Zener, iNTS2A

Inductors

Inductor, 15 mB Jaductor. 9.8 pIt Inductor, 7 pH (Acceptable substitute is part no. 99-211051) Inductor, 2.2 pH Inductor, 1.5 mH

Resistors

RU, RZ Resistors, Carbon Film, 180 kOhm, £5%, 1 W R3 Resistor, Wirewound, 120 Ohm, +5%, 2 W Ri Wirewound, 0.47 Ohm, 45%, 2. W RS Resistor, Wirewound, 27 Ohm, +5%, 2 W

RO, RFResistor, Carbon Film, 5.6 Ohm,4 1/4 We

RB Resistor, Wirewound, 0.47 Ohni, +5%, 2 W

ROResistor, Carbon Film, 10 Ohm,£5%, 1/4 W
RIOResistor, Carbon Film, 1 kOhm,45%, 1/4 W
RMResistor, Carboa Film, 47 Ohm,5%, 1/4 W

R12 Carbon Film, 5.6 Ohm, 45%, 1/4 W R13 Carbon Film, 330 Ohm, £5%, 1/4 W R14 Resistor, Carbon Film, 270 Ohm, #5%, 1/2 W

R15 Resistor, Carbon Film, 330 Ohm, +5%, 1/2 W

RIGResistor, Carbon Film, 8.2 Ohm,+5%, 1/4 W

R17, R18 Resistor, Carbon Film, 56 Ohm, +5%, 1/4 W RIS Resistor, Carbon Film, 39 Ohm, +5%, 1/4 W

R20 , Carbon Film, 2 kOhm, +3%, 1/4 W R21 » Carbon Film, 470 Ohm, +5%, 1/4 W

R22 , 2.2 kOhm, £2%, 1/4 W R23 Metal Film, 2 kOhm, +£2%, 1/4 W

R25 Carbon Film, 10 Ohm, #5%, 1/4 W R26 Carbon Film, 6,8 Ohm, £5%, 1/2 R27 , Carbon Film, 12 Ohm,

R28Resistor,Carbon Film, 2.4 Ohm,

R31 Resistor, Wirewound, 150 Ohm,

Transistors

QlTransistor,NPN. 28725

Q2 Transistor, NPN, PE80S0B Qa ‘Transistor, PNP. PE85S50B.

Miscellancous

Fl Fase, 2 4, 125 V, Semko

clRegulator,VAd SLAW

SCRI Thyristor, SCR aa) Transformer 99-211005, 99-21 1008 99-211007

99-211052 99-211 071 99-211050 99-211054 99-211053

99-211034

99-211027 99-211018 99-211029 99-211032

99-211025 99-21 1027 99-211026 99-211023

99-211022 99-211028 99-211031 99-211030

99-211035 99-211024

99-211021 99-211033

99-211929 99-211066 1067 211068 99-211016

99-211062 99-211003 99-211063,

99. 99-2 99-211013 99-21 1035

Page 41

cyberbalt Mlustitted Pants tists

Mitrou 5V. IZA Power Supply Assembly Parts List, Continued

Designater Description Part No.

Ve on 214055, PRI ge athe vid ou pola

base, 228 \ YO TEIOSO Fuse Helder ONT G0 Fermunal blocs, 8 Cht 89-21 1GRT Heat Sink 99-211059 Heat Sink. 1.4 pan 99-21 1001

Page 42

Mlustiated Parts Lists eybetball

99-10140 Panei Assembly

75-9488 Lock:

: 99-10116

99-10152 : Iw Raght Corn inlet 99-10147 Harness 171006-035 Cain Mecnanism

75-9448 Locknut

99-10096 Fastener

99-10151 Lefi Coin Inet

70-11-47 Lamp

99-10080 Lamp Socket

99-10105, 72-9406S Bar Screw

99-10104

99-10042 thru 99-10045 ao Coin Swatch Assembly ~ mm 99-10150

65-441C ee Switch Cover Coin Swich

99-10075 thru 99-10078 ~ | a 3wiich Wires Ss I 99-10008 . Relaner 75 sang

Screw 99-10154 Bracket Assembly

99-10153 Coin Return Bex

99-10068 Coin Chuie

Figure 4-5 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

Page 43

Cyberbatl Bshuest ated Parts Last

99-10148 Lock Assembly

99-10142

72-HAI404C Screw

99-10134 99410119 Cover 99-10139 MA pemensscemily | gear Cam Deor 9 \ L + Buttons a oe 99-1015 ie Spang » 99-10148 Lock Assembly.

72-JA1405B i Z\— 99-10144 Screw i I. a Chanre! Chip. i, i” ~~ 99-15068 74 Screw 99-10149 Service Door

038091-01 Coin Box

99-10143 Frame

Figure 4-5 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A

Page 44

Hlusteated Pats Lists yberbail

Coin Acceptors, Inc. Coin Door Assembly Parts List

Description

Coin Switch Minature Bayonet Lamp 24-10 x 3°SInch Truss-Head Screw a4-40x Linch Pan-Head Screw

e440 % Al-lach Pan-[ead Serew a-aQ X 3. 4-Inch Pan-Heud Screw s4-i0 Locknut Retainer

99-1042 Coin Switch Assembly (or Belgian 5 Frand U.S, 25¢ 99-10053 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-100544 Coin Switch Assembly for German 2 DM, Italian 100 1. U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P

99-10068 Coin Return Chute 99-10075 Switch Wire (included in coin switch assembly 99-10043) 99-10076, Switch Wire Gincluded in coin switch assembly 99-10042) 99-10077 Switch Wire (included in coin switch assembly 99-10044)

99-10078 Switch Wie Cineluded in coin switch assembly 99-10045) 99-1080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener 99-10104 Bar Retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever

99-10117 Steel Coin Return Door 99-10139 Coin Door 99-10140 Coin Door Innes-Panel Assembly 99-10141 Die-Cast Coin Return Cover

99-10143 Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly

99-10149 Service Door 99- 10150, Switch Cover 99- 10151 Left Coin Inlet 99-10152 Right Coin Inict

99-1015, Coin Rewrn f 99-101 Bracket Asi

99-10160 Linch Wide Dic- Coin Intet Housing, 99-10161 25¢ Amber Side-Entry Coin Bution Assembly 99-15066 serew for Clamp tal Coin Mechanisin for US 171006-035 \

4-16

Page 45

Mustratedl Parts Lists

Page 46

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 47

Cobol

Design,

IB

nN iM IN 2p

OL.

sl

Sh

HLA Cyberball Game PCB Assembly Parts List

Description

Integrated Cire ned Circuit, PROM, avated Circuit, EPROM ek Circuit, TAL S197 gaticd Crean, “P02 300)

abated Gia, EPROM, 275 12-3u0 saved Circuit, EPROM 300 ed Crcuit. BML TOLS A red Cireuit, Tal S20

ic Gireuit, TLS 157 Integrated Circuit, EPROM sue Integrticd Circuit, EPROM. ann) Imegeted Circuit, “418157

Integrated Circuit, 2804 A-15, 450 nsec Integrated Circuit. SCOM Integrated Circuit, PAL. TORO A. Integrated Circuit, 715245

nsec (Acceptable substitute is -028.) Integrated Circuit, RAM, 8K x 8, 7( part no. 137588-005 with socket part no. Imegrated Circuit, 7418245 Integrated Circuit, PAL, 16R6 A Integrated Circuit, 74L808

ed Circuit, 68000, Integrated Circuit, RAM, 8K x 8. 70 nsec (Acceptable substitute is part no. 137588-003 with socket part no. 179259-028.) ject Circuit, OS000, SMHZ. PLAS ated Circuit, T4LS74 SMHZ. PLAS

uted Circuit, edd Circuit wed Circuit ed Circuit

cull

PCT 1¢

Integrated: Circuit, ~

sited Circunt soated Circuit Integrated Circuit Integrated Circuit

Integrated Circunt, 7 Integrated Circuil. ed Circuit, ed Circuil,

ated Circuit. 7. ated Circuit, F41S245 Integrated Circuit, RAM. SK ox 8.45 nsce (Acceptable substitute is parl no. 137 JOS with socket part ne. 179259-028.) htegrated Circuit, OTP, 2 lystyatted Parts Lasts

Part No.

136004-2128 13601012129 HUE Us7ast-001

[40042124 Pao0G 42728 1s00 4-136 137 ben 00]

TATHSENOL J 3000 1ao004-2127 favs

7526-001 1300641145, Ps7134-001

13004-1146 137012-001

137289-003

137535-003 137289-004 137023-001

1S7019-061

1371 14-001

137009-G01 137591-001 437012-001 137177-001

137019-001 137436-001 137144-001 TA7069-001

137591-001 137134-001

157535-001 146061117

rid

Page 48

Ilustrated Parts Lists.

Cyberball Game PCB Assembly Parts List, Continued Cyberball

Designator Description Part No.

8NIntegrated Circuit1S7131-001
SAIOA,Integrated Circuit, 74LS:TAT T44-001,
9/}0BIntegrated Circuit, 7418139137097-001
9f10C, 9/101Integrated Circuit, 7418374137 144-001
9 1OEIntegrated Circuit, 741515717029-0001
Of0FIntegrated Circuit,741832147019-004

9/10) rated Circuit, 7418153 137104-001 9A rated Civcuit, VMATCH 137552-001

9c. 9DIntegrated Circuit, 7418374137144-001

OE integrated Circuit, 74F04 37-001 oF Integrated Circuit, 7418245 Oo] Integrated Circuit, 7418153

9K Integrated Circuit, RAM, 8K x 8, 45 nsec (Acceptable substitute is part no. 137589-003 with socket part ao. 179259-028.) OL Integrated Circuit, OFP, 2751 1O/11D, 10/11E, 10/11F 10/11)

0A 10B, 10C 10K

JOL/M

10N HA 1c MD, 116, 11F

11K

1IL/M 11M

12A, ize 12D, 12E 12F

12) 12k TALIM. 12N 134A

13€ 13D, 13E, 13F GB 13K

ISL/M, 13N 4A He 14D, 14E Integrated Circuit, 74183 Integrated Circuit. 74LS.

Integrated Circuit, 7418374 Integrated Circuit, 7418245 Integrated Circuit, RAM, 8K x 8, 45 nsec (Acceptable substitute is part no. 137589-003 with socket part no. 179259-028.) Imegrated Circuit, OTP, 27512-250

Integrated Circuit, 7415 Integrated Circuit, OTP, 27512-250 Integrated Circuit, OTP, 27512-250 Integrated Circuit, 7415374

Integrated Circuit, 74L$153 Integrated Circuit, RAM, 8K x 8, 45 nsec (Acceptable substitute is part no, 137589-003 with socket part 0. 179259-028.) Integrated Circuit, OTP, 27512-250 Integrated Circuit, 741.504

Integrated Circuit, OTP, 27512 Integrated Circuit. Integrated Circuit, 7 Imegrated Circuit. 7

Integrated Circuit Integrated Circus. integrated Circu Integrated Circuit, OTP,

Integrated Circuit, OTP. 275 Integrated Circuit, 7415191 Integrated Circuit, 7418153 Integrated Circuit, 74F374

Integrated Circuit, PFHS Integrated Circuit, OTP, Integrated Circuit, OTP, Integrated Circuit, 74163 137535-001 136064-1149

137134-001 136064-1151 136064-1153 137144-001

137104-001

137535-C01

136004-1155 136064-1157 1 36-001 137029-001

137 104-001 137-126-001 TATSSOG 1A6004-1150

130064-1161 137036-001 137 104-001 137420-001

137A19-104 136004-1403 136064-1165 345-001

Page 49

Cyberball

jake a Lik 15/164 15106

15D, 15 ISP 5) 15K. 15M

16D. 16£

J6F 16) 16K 16M

16N 17D, \7E VF 1s

17K 17L 17M 17N

18A, 18C 18D, 18E 18F

18) 18K 18L, 18M 18N

19A 19C 191, 19E 1OF

YOK 191, JOM

20A,. 2015 Cyberball Game PCB Assembly

ied Circuit, tied Circuit ied Cieuit.

Integrated Circuit,

Integrated Integrated Integrated Circuit, ail, Tircuit

Inegrated Circuit, 7

Integrated Circuit. Integrated Circuit, Integrated Cire Integeated Circuit,

Integrated Circuit, Integrated Circuit, Integrated Circuit, integrated Circuit,

Imegrated Circuit, Integrated Circuit, Integrated Circuit, Integrated Circuit,

Integrated Circuit, Integrated Circuit, Integrated Circuit, Integrated Circuit,

Integrated Circuit, wed Circuit, Integrated Integrated Circuit

sited Circuit, arated Circuit Iniegrated Circuit Integra Description Parts List

TALS 1ST “UESISA orn. OTP, 2

» THRLOS TaLSIV1 . TALS TS8 SOS

74LS138 1018 A

74F 163 PAL, 1618 A PAL, 16R8 A

AFO4 74F534 7406 74F534

OTP, 27512-250 OTP, 275 74F163 7ALS74

PAL, 16R8 A 7ALSRO » FAPS7A 7ALS260

PAL LORS A PAL. IGLS A FALS153, Mlustrated Parts Lists

Part No.

1s7029-001 VAT HW-008 13600-1150 10001-1152

147 345-00] 137046-001 137177-001 137580-00]

13600-1106 136064-1154 136064-1156 137345-001

13006-4-4107 137345-001 136004-1141 136064-1138

137599-001 137052-001 137590-001

136064-1158 136064-1160 137345-001 137023-001

136064-1137 137079-001 137420-001 137332-001

136004-1162 1S6004-11G4 13745001 1aT327-001

180001 LU Taobo bibl ST iavoy 5-00]

1s Laat 1730-005

iezenti

Date onl mee Mi]

Page 50

Ulusteated Pants Lists Cyberbatl

Cyberball Game PCB Assembly Parts List, Continued

Designator Description

21A, 2B Integeied Circuit, T4LS374 21c Integrated Circuit, 741886 21D, 21D/E, 21K, 21E/P Integrated Circuit, RAM, 2KNS. 35 nsec

21FIntegrated Circuit, 74FOObSTa27-001
  • ated ~ 7aR 25 J37591-001
21KAntegrated» TALS153137104-004

2iL Integrated Circuit, 74374

21MIntegrated Circuit, RAM, 2KX8, 35 nsec137534-001
2iNIntegrated Circuit, 7415260137332001
22A, 228Integrated Circuit, 7418374:137144-001
22Integrated Circuit, 741874q
22F, 22)Integrated Circuit, 74F00137327-001
22KIntegrated Circuit, 7418153137104-001
221Integrated Circuit, 74F374137420-001
22MIntegrated Circuit, RAM, 2KX8, 35 nsec137534-001
22NIntegrated Circuit, 74F157137494-001
23A, 23BIntegrated Circuit, 7418374137144-001
23CIntegeated Circuit,137023-G0L
23Fintegrated Circuit,137591-001
23}Integrated Circuit, 7418174137122-001
23KIntegrated Circuit. PAL, 16L8 A136064-1143
23LIntegrated Circuit, 7415153137104-001
23MIntegrated Circuit. 74HC273137556-001
23NIntegrated Circuit, 7406137052-001

Integrated Circuit, SOS 137550-001 Integrated Circuit Integrated Circuit, 137938-001 137590-001 Integrated Circuit, 137009-001

  • Integrated Circuit 24K Integrated Circuit 241 Integrated Circuit 24M Integrated Circus, 7

038-001 590-001 Integrated Circuit. 7 Integrated Circuit, Iniegrated Circuit. 7 Integrated Giscur. 7 137591-001

25KIntegrated Circuit, 7418153137 164-001
25LIntegrated Circuit, 74F374137420-001
25MIntegrated Circuit, RAM. 2KX8, 35 nsec137534-001

25N Integrated Circuit, 7418260

20B/C Integiated Circuit, SOS. 26D 7ALS244

26FIntegrated Circuit. 74F3747
26FIntegrated Circunt37591-0901

264 Cireen, 7 U37420-001 26K ated Circuit 74LS153 137104007

201.Integraled Circuit, TARS74137420-001
Page 51

Cyberbal Mlustratcdl Parts Lists

Cyberball Game PCB Assembly Parts List, Continued

De: ption

of Circuit, RAM LE Cteutt, TES

Capacitors Part No.

Cl, C2} pF 50. V. Ceramic122002104
37 pF 28 V, Blecuolvuc121009- 70
C4F30.V, Ceramic£22002.)04
cs.25. V, Hlectrolytic121009476

C6, C7 pacitor, 100 pF. 100. V, Ceramic cs ”apacitor, .1 pF. 30 V, Ceramic C9-C12 100 pF, 100 V, Certmic C13-CA2 pacilor, 1 pF, 30 V. Ceramic 122002-104

C43-C54 citar, 100 pF, 100 V, Ceramic 2 22016-1001

€115-C129 Capacitor, .1 uF, 50 ¥. Ceramic Capacitor. .1 pk, Ceramic Capacitor, .1 pF. 50 V. Ceramic

Capacitor. 1 350 V. Ceramic 12202-1004 122002104 122002-104

122002-104

C131Capacitor, .1 pF,50 V. Ceramic122002-104
C134-C140Capacitor, .1 pF, 50 V. Ceramic122002-104
C142-C157Capacitor, .1 pF, 50 V, Ceramic122002-10+4

Inductor

LlInductor, 100 pH141024-001

Diode cRI Diode. MV5053. Light-Emitting

Resistors RL Resistor, 220 Ohm,#5%, 1/8 W

R2Resistor. 100 K Ohm,+5%, 1/8 W

R3-RO Resistor, 1 K Ohm, +5%, 1/8 W

R7, RDResistor, 100 Ohm, +5%,1/8 W

Ri, R12 Resistor. 1 K Ohm R13 Resistor, 100 Ohm, RIS Resistor, 1 K Ohm, + R16-R31 Resistor, 470 Ohm. #

R32, R35,Resistor, 100 Ohm, #5%,1/3 W
R36-R38,Resistor, 1 K Ohm,sw
R39, R41, RAZResistor, 100 Ohm,Les W110027 101
R43, RAGResistor. 10 K Ohm1's Wond 103

|, RAD, R52, RSS Resistor. 1] K Ohm Resistor. 470 Ohm 1,8 W Vvew Elng27- 12

Resistor, 1 K Ohi Vew Resistor, 47 Ly Ww

sw 110027- 102 aw Ha 1

1K ObmSWHIGHT 102
ROS-RIOL:70. Ohaiawows

RIG2ZKIO9 RYIO-RIN7 Resistor, 1K Olin Resistor, 470 Ohne sw rsw 1oo27 jos Hon

Page 52

Mlustrated Parts Lists

Cyberball Game PCB Assembly Parts List Cyberbail

Designator Description Part No.

RI1S-R123Resistor, RIK118016-001

R324 Resistor, 22K Ohm, £5%, 1 8 W -222 R125 Resistor, 1 K Ohm, 45%, 1.8 W R126 Resistor, 2.2 K Ohm, £5%, 1 8 W

R127 1K Ohm, 45%, LS W 110027-102

R128» 2.2K Ohm,45%, 1:8W11002
R129Resistor, 1 K Ohm,+5%, 1/8 W
R130-R132Resistor, 220 Ohm,#5%, 1/8 W110027-221
R133, R134Resisior, 10 Olm, +5%, 1/8 W110027-100
R135.Resistor, 100 Ohm, +5%, 1/8 W110027-101

R136, R137 Resistor, 10 Ohm, #5%, 1/8 W

R138Resistor, 100 Ohm, #5%, 1/8 W140027-101
R139, R140Resistor, 10 Ohm, 45%, 1/8 W110027-100
R141Resistor, 100 Ohm,+5%, 1/8 W

R142 Resistor, 1 K Ohm, +5%, 1/8 W R143 Resistor, 2.2 K Ohm, +5%, 1/8 W

R144Resistor, 1 K Ohm, +5%, 1/8 W110027-102
R145Resistor, 22 K Ohm, +5%, 1/8 W110027-222
R146Resistor, 1 K Ohm, +5%, 1/8 W110027-102
RIA7Resistor, 2.2 K Ohm, +5%, 1/8 W110027-222
R148-R150Resistor, 220 Ohm,+5%, 1/8 W110027-221
RIS1, R152Resistor, 10 Ohm, +5%, 1/8 W110027-100
R153Resistor, 100 Ohm, +5%, 1/8 W110027-101
R154, R155.Resistor, 10 Ohm, +5%, 1/8 W110027-100
R136Resistor, 100 Ohm, #5%, 1/8 W110027-101
R157, R158Resistor, 10 Ohm, £5%, 1/8 W110027-100
R159Resistor, 100 Ohm, 45%, 1/8 W110027-10)
R160-R162Resistor, 1 K Ohm, +5%, 1/8 W110027-102

Transistors

QlTransistor, 2N5306133033-001
Q2-08Transistor,2N3904133041-001

Sockets Socket, 14 Pin, 300 Inch 179257-014 Socket, 24 Pin, .300 Inch 179259-024 , 24 Pin, .600 Inch 179257-024 28 Pin, .600 Inch 179257-028 40 Pin, .00 Inch 179257-040 Socket, 64 Pin, .900 Inch 179256-064

Connectors

AUDConnecior, 11 Ckt. Header, 300179118-011
VIDI, VID2Connector, 11 Ckt, Header, .100179118-011
WwhpIsConnector, 2 Ckt, Header, .100 Ctr179048-002
CTRConnector, 11 Ckt, Header, .100179118-011
PLY1-CTR4Connector, 11 Chi, Header, 190\W911s-011
PWRConnector, 6 Ckt, Header, 230 Cur173069-000
WDDISCoanecior, 2 Ckt, Lidr, 100 Cu179048-002

Miscellaneous Test Point 179081 UOT

Page 53

Cyberball Mlustiatcd Parts Lists

~ oh THe aT « D ISO o PD ow

a w THe KT Tite war THs 7s Oe

  • pag hee ig a ‘mit i ao eo : ee Oe Se ; Fe amp He BR” a oe i ae 7 fe ass] Ee =

scone were on, Ba" 233 AT Mn Ge ae

Figure 4-7 SAC (Sampled Audio Cruncher) PCB Assembly A044963-21 A

SAC PCB Assembly

Parts List

Designator Description Part No. Integrated Circuits 1c Integr ated Circuit, 7418240 Integra ned Circuit,

Integrated Circuit, SC OM

EPROM, 27512-300 ns . RAM, 8K x 5, 100 ns 65 : TAS273 147040-001

Page 54

Hustrated Parts Lists Cyberball

SAC PCB Assembly Parts List

7058-001 157 144-001 137023-001 alt Integrated Ci Wad Integrated Circuit, ah Integrated Cire

iIntegrated13064-1173
iIntegrated Cixcuit, Y!137401-001

5A Integrated Circuit, EPROM, 27512-200 ns (Acceptable substitute is OTP, 27512-200ns, part no.130064-1170.) 13004-1134 3C Integrated Circuit, EPROM, 27512-200 ns (Acceptable substitute is OTP, 27312-200ns, part no. 136064-1168.) 13004-1132

SEIntegrated Circuit, RAM, SK x 8, 100 ns.137535-004
3Integrated Circuit, 7418138137177-001
suIntegrated Circuit, YM3012137402-001

. Integrated Circuit, TLO84C) 137579-001 Integrated Circuit, 7418373, 137143-001

ouIntegrated Circuit, 7418374137144-001
4]integrated Circuit, AMG012137158-002
OKImegrated Circuit, 7407137011-001
OLIntegrated Circuit, 40168137592-001

A Imegrated Circuit, EPROM, 27512-200 ns (Acceptable substitute is 200ns, part no. 136064-1171.) 130004-1135 7 Integrated Circuit, EPROM, 00 ns (Acceptable substitute is OTP, 27512-209ns, part no. 136064-116).) TE Integrated Circuit, RAM, 8K x 8, 100 ns

7FIntegrated Circuit, 7418373137143-001

Integrated Circuit, 7415174 137122-001 Integrated Circuit, 741832 137019-001 Integrated Circuit, 7406 137052-001 Integrated Circuit, PALIOR4 136064-1174

7Integrated Circuit, TLO84CN137579-001
spImegrated Circuit, 68000, SMIIz, PLAS.137289-003
5]Integrated Circuit. PALIOLS136064-1172
SKIntegratedCircuit, 74.808137012-001

SL Integrated Circuit, 74 t

SMIntegrated Circuit, 74.8163 A137114001

Capacitors Capacitor, .4 jal, 50 V, Ceranuc 1221002-104 Capacitor. 190 pF, 100 V, Ceransic

oyCapacitor, «1 il, 50 ¥, Cerasiic122002-104
cwCapacitor, 10 ph, 25 V, Electrolytic124009-100
Cuc14Capacitor, 1 pF 58. V,¢“122002-104
C15Capacitor, 29 pF. 100.\, Ceramic6-3

Capacitor, 100 pF, 100 V, Ceramic 16-101 Capacitor, 1 yh 50 V. Cerany AS2-1O4 Capicitor, 10 ph 25. VE astio 909-106, Capacitor, 22 V. Elvetrolvuc 900-226

4-26

Page 55

Cyberball Mlustented Party Lists

SAC PCB Assembly Parts List, Continued

Part No.

22 WF, 210%, 50 V, Ceramic jE, a5 V. Electrolytic Capacitor Capacitor Capacitor, 22 fu £10», 50 VW, Ceramic Capacitor, 1 pF 50.V. Ceramic 122002-104

Capacitor, S400 p28 V, Electrolytic, Radial 123003-333, 1 ph 50-V. Ceramic 122002-104 10 pF. 25 V, trolytic 12-4009-106 , 1 pF, 50.V. Ceramic 122002-104

mic ctrolytic

pacitor 30 V. Ceramic pacitor, 0. V. Ceramic Capacitor. 0 V, Ceramic

Capacitor,» 100 V. Ceramic122016-122

acitor, 70 pF, 50 V, Ceramic 122015-471 1200 pF. 100 V, Ceramic ', 10 pF, 100 V, Ceramic 122016-100 Capacitor, .1 pF, 50 V, Ceramic 122002-104

C62, C63Capacitor. .001 pF, 50 V, Ceramic122002-102
64, CO4ACapacitor,5%, 100 V, Poly, Radial126009- 103
C65Capacitor,0 V, Ceramic122002-104
C66, CO6ACapacitor,, £5%, 100 V, Poly, Radial126009-103
C67, C68Capacitor, 2000 pF, £3%. 500 V, Mica128004-202
C69Capacitor, 1000 pF, 100 V, Ceramic122016-102

C70, C7 C72 001 UF, 50 V, Ceramic 122002-102 , 1900 pF, 100 V, Ceramic

. 4700 pF. 30 V, Ceramic 122019-472

F,V. Ceramic122002-104

100 V, Ceramic 015 pF, £5%. 100 V, Poly, Radial 326009-153

. 1100 pF, #5%%, 100 V, Mica . 300 pF, 100 V, Ceramic 91 pF, 50 V, Ceramic . 3G00 pF, £5%. 500 V. Mica 12800-1-462

10 pR i00.V, Ceramic 1220 16-101 PUCHOr, JS PE, 23%, 50 V, Poly, Racial 126008-393,

Capacitor, 01 ph 50. V. Ceramic 96 Capacitor, 22 pF, 410%. 50 V, Ceramic, paeitor, 109 pF, 160 V, Ceramic Capacitor, 015 pF. £5%, 100 ¥, Poly, Racial

coyCapacitor, S608) ph,25%,300 V) Miva
C1buCapacitor, P1G0 pi 5100,V. Mica

ctl Capacitor, 569 pF, 100. Ceramic lols Gapackor 1h Sa.V, Ceramic

Page 56

Mlustraied Parts Lists Cyberbail

SAC PCB Assembly Parts List, Continued

Designator Description Part No.

Diodes

CRIDiode, MV5054, Light-Emitting131027-002
CR2-CRSDiode,1N5402131051-002
CRO, CRFDiode, MV5053, Light-Emitting131027-002
CRS-CRI3Diode, 1N4001131048-001

Inductor

uuInductor, 100 pH141024001

Potentiometer

PoriPotentiometer 10K Ohm, Horizontal, Dual119011-103

Transistors

QlTransistor, 2N5306133033-001
2Transistor, 2N390413304 1-001
3Integrated Circuit, LM317137233-001
Q4Integrated Circuit, [M337137232-001
Q5Integrated Circuit, [M317137233-001
Q6, QFIntegrated Circuit, TDA2030137301-001
Q8, Q9Transistor, 2N5306133033-001

Resistors

RLResistor, 470 Ohm, £5%, 1/8 W110027-471
R2Resistor, 0 Ohm, +5%, 1/4 W110005-001

R3 100 K Ohm, +5%, 1/8 W 119027-104

R4-R12Resistor, 1 K Ohm, +5%, 1/8 W110027-102
R13Resistor, 470 Ohm, £5%,110027-4
R14, RISResisto;110027-102
R16Resistor.110027-471
R17Resistor, 220 Ohm, +5%, 1/8 W110027-221
R18, R19Resistor, 10 K Ohm, £5%, 1/8 W110027-103

Resistor, 68 Ohm, 5%, 1/8 W Resistor, 220 Ohm, £5%, 4/8 W Resistor, 10 K Ohm, £5%, 1/8 W

Resistor, 1 & Ohm, #5%, 1/8 W Resistor, 10 K Ohm, +5%, V8 W Resistor, 1 Ohm. + V4 W Resistor, 1.8 K Ohm, +5%, 1/8 W

R33 Resistor, 240 Olim. 25%, 1/8 W %, 1/8 We 45%, 1/8 W R34 Resistor, 1 K Ohm, R35, Resistor, 10 K Ohne R36 Resistor, Ohm, +5%, 1/8 W

R37, Resistor. 1.8 K Qhm. R38 Resistor, 240 Ohm, R39 Resistor, 560 Ohm, RAG, R41 Resistor, 22 K Ohm, 45%

RAZ, RAB Resistor, 10K hin, £5%, 1/8 W Rid Resistor. 470 Ohm, £5%, 1/8 W Ras Resistor, 560, 25%, 1/6 W RAG Resistor, 10K Ohm, #5%, 1/48 W 110027-680 410027-221 110027-103

110027-102 140027-103 110000-010 110027-182

110027-241 110027-162 110027-103, 110027-241

Page 57

Cyberball Ilusteated Parts Lists

SAC PCB Assembly Parts List, Continued

K Ohm, £5%. 11002 Resistor. 10 K Olin, £5%. i002 Resistor, 4.7 K Olum, £5°%. 10027-4772 12K Obm, #5%, Hoo

Resistor,1K Ohm. 25%.410027102

Resistor, 10K Ohm, 110027-103

Resistor, 27 K Ohm, £4%. 18W11002"-273
Resistor,LK Ohm, 25%, 1/8 W110027-102
Resistor, 12 K Ohm, 25%, 1,8W119027-122
Resistor, 3.9 K Ghm,#58,18 W110027-3
Resistor.1.8 K Ohm, 5%, 1/8 W110027-182

Resistor, 10. K Ohm, +5%, 18 W 41002

R61Resistor. $2 K Ohm,Ls wv110027-823
RO2Resistor. 1.8 K Ohm, £5, 1/8 W110027-182
ROBResistor, 10 K Ohm, +5%. 1/8 W110027-103
ROAResistor, IS KOls W1410027-183
ROS, ROOResistor. 7.5 K Ohm, £59%, 1/8 W110027-752
RO?Resistor. 82 K Ohm,#5%, 1/8 W110027-823
ROSResistor. 18 K Ohm, 459%. 1/8 W110027-183
ROO, RTOResistor, 1 K Ohm, +£5%, 1/8 W1 10027-3102
R71Resistor, 470 Ohm, £5%, 1/8 W110027-471

Resistor, 20 K Ohm, £5%, 1/8 W’ 110027-203 Resistor, 10 K Ohin, 1/8 Ww R74 Resistor. 1 K Ohm, £5%, 1/8 W

R75-R77 Resistor, 10 K Ohm, £5%. 1/8 W

R78Resistor, 1 K Ohm,ig W

R79 Resistor, 3.6 K Ohm, + R80 Resistor, 24 K Ohm, %, V8 W

  • 1/8 W
RedResistor. 7.5 K Ohm,£5%.

RS2 Resistor, 20 K Ohm, £5%, 18 W

RRBResisior, 100 K Olin, £5%.1/8 W

R84 Resistor, 6.8 K Ohm, £57, 1/8 W

RSSResistor, WK Ohm, 25%,18 W
RAResistor.2K Ohm.Ls W
RSTResinor, 22 K Oban, £5%,18 W
RESResistor, 20K Ohin, £98,18
RyResistor, 22 K Ohm110027-224
ROOResision. 6.5 K Olin:11002
ROResistor11002

ROZ Y 1QG2

ROSResistor, 2:11902
RYResistor,1002
RYS,Resistor, 7.5 K Ohm. 45%, 18W1M
ROGResistor, 160 K Ohin,Law11027-1604,
ROF-RIYResistor. 1 K Ohm.W110K2
RiV0Resistor, 1 Ohm» LAW110006100

6 Ohm, 110005-001 RIG Kesint

Page 58

Ilusteated Parts Lists, Cyherbalt

SAC PCB Assembly Parts List, Continued

Designator Description RNI stor Network, 1K x 5, #5%, 1/8 W, SIP (o Pin)

Connectors

ICOIN, JSPK Connector, 6 Cit, Header, 100 Cu, Key 5 JSCOM Connector, 11 Ckt, Header, .100 Ctr, Key 3 ACDC Connector. 12 Ckt, Header, .156 Ctr, Key 11

Sockets

4H Socket, 24 Pin, .600 Inch 2K, 2H, 7E, 5E Socket, 28 Pin, .600 Inch 5A, SC, 7A. 7C Socket, 32 Pin, 600 Inch : 3C Socket, 40 Pin. .600 Inch

8pSocket, 64 Pin, .900 Inch179256-064

Miscellaneous

XICrystal, 14.318 Mhz144000-004
HS1, HS2Heat Sink, TDA2030178190-032
STESTSwitch, Slide160640-001

Test Point 179051-001

4-30

Page 59

Cyberball HMusteated Parts Lists

If You Have Sanyo Video Displays. . .

Games with Sanyo video displays have a few different parts in the cabinet-mounted assemblies, power supply arts ue Most Cyberhball games have Wells-Gardner video displays. However. some have Sanyo video displays. Check the label on the back of your video display assembly and the game PCB assembly, These chassis for the manufacturer's name. If you have Sanyo listed below video displays, check this page before you do any repairs or order any parts

Changes to the Cabinet-Mounted Assemblies, Figure 4-1 Old PartNo. _______New Description _ . a ______ New Part No.

A046202-01Video Harness Assy (100 V)OoAQ1G471-01
A040203-01Video Power Harness Assy C100 V)AG16470-01

‘Tinted Display Shield 04616:

139017-305Sanyo 19-Inch Color Std. Res. Video Display13902
TM-296Sanyo 19-Inch Std. Res. Video Display Service ManualTM-311

Changes to the Power Supply Assembly, Figure 4-1 _

Old Part No._New Description—_New Part No.
142045-001Transformer (00V/120V)‘A044337-01

Changes to the Cyberball Game PCB Assembly, Figure 4-6 _ oe Designator New Description _ _ _ . Ri24 2.2 KQ Resistor

R1262.2 KQ Resistor0027-122
R1282.2 KQ Resistor11Q027.

RISd 17 Q Resistor

RIS? 17 Q Resistor Riad 17 Q Resistor R43 2,2 KO Resistor R145 2.2 KQ Resistor

R147 2.2 KQ Resistor R152 Q Resistor RIS 7 Q Resistor

R15847 Q Resistor110027-470
Page 60

Illustrated Party Lists

N Cyberball

S

Page 61

Cyberball” Statistics Sheet

Statistics Screens

First Statistics Screen Second Statistics Screen

Left Screen, Left Mech Coins Percent Left Screen, Right Mech Coins Computer Games Left Right Screen. Left Mech Coins Computer Games Right Right Screen, Right Mech Coins Human-Human Games Total Games 1 Period Games ee 0 Player Minutes ! 2 Period Games 1 Player Minutes ! 3 Period Games 2 Player Minutes 4 Period Games 3 Player Minutes 5 Period Games 4 Player Minutes | 6 Period Games _ Error Count | 7 Plus Period Games Total Credits Average Time per Credit

Histogram Screen

SecondsNumber of CreditsSecondsNumber of Credits
0-39__.220-239
40-50__240-259

60-79 80-99 260-279 280-299 100-119 300-319

120-139__320-339

140-159 160-179 340-359 _ 360-379

180-199_380-399a
200-219_400-Up
Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective; Such products are returned prepaid to Seller's plant; and (© Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty, The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 64

6 AME A ” 57:

Milpiiss, Calvamta 95035 P.O Bos 361119 Alan Games Corporat) S Sycamora Chive