CATHODE RAY TOMES

Lemans TM-077 1st Printing

Le Mans (Atari, 1976) · Technical Manual · 84 pages · 25 sections · original scan

Page 1

7M077 1st printing

"LOA\GIG

Operation, Maintenance, Service Manual

Page 2

PS r

&

?

? r ? ? ?

?

This document is and contains confidential trade secret information of Atari, Inc. ee

WARRANTY

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety

  • days from date of shipment. Seller warrants that its television monitors are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY 1S EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER’S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 3

Le/Aans

Operation, Maintenance and Service Manual

ATARI INC. 14600 WINCHESTER BLVD LOS GATOS, CA 95030 408/374-2440 e TELEX 357-488

By the Publications Group, Engineering Department AM

ATARI

ATAR

leisure

Page 4

All rights reserved. Copyright © 1976 by Atari, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

For permission requests, write:

Atari, Inc. Engineering Dept. Publications Group 14600 Winchester Blvd. Los Gatos, Calif. 95030

Lithographed in the U.S.A.

Page 5

Table of Contents

GENERAL MAINTENANCE AND SERVICE ........................00.000005 1

1.1 Introduction and Warranty Information ............ 6000. c eee cence eens 1

1.2 Access and Basic Construction ......... 0 ccc cece neee eee ees 7

1.3, New Machine Set-Up and Checkout Procedures

1.4 Game Sequence... 6. cece cc teen ttn tne teen ees 2

1.5 Antenna Wire and Anti-Static Modification... 00.6.6 6 cece eee eee 2

1.6 Vand Lighting: Service Procedures ............ 060 cc cece eect e eee n eens 3 1.6.1 General Illumination Lamps 1.6.2 Plexiglas Screen 1.6.3 Bezel 1.6.4 TV Monitor Removal 1.6.5 TV Monitor Adjustment

1.7. Coin Door: Service Procedures ... 1.7.1 Door Lock 1.7.2 Reject Linkage 1.7.3 Coin Micro Switches 1.7.4 Coin Acceptors 1.7.5. Acceptor Adjustment 1.7.6 Acceptor Maintenance

1.8 Electronics Tray Subassemblies: Service Procedures .......++-.060ee eens 5 1.8.1 Fuse Replacement 1.8.2 Transformer Replacement 1.8.3 Interlock Switches 1.8.4 Printed Circuit Board 1.8.5 PCB Adjustments

1.9 Mechanical Controls: Service Procedures ......... 01.00 c cere eee e eee e eens 6 1.9.1 Control Panel 1.9.2 Gear Shifter Assembly 1.9.3 Pedal Assembly 1.9.4 Steering Wheel Assembly

1.10 Regular Machine Maintenance ......... 0.66 e cece etter tenets 6

1.11 Troubleshooting Procedures 1.11.1 TV Monitor 1.11.2 Printed Circuit Board 1.11.3. Wiring Hamess 1.11.4. General Suggestions

Page 6

Table of Contents

1.11.5 TV Monitor Troubleshooting 1.11.6 Steering Assembly 1 Troubleshooting by Symptom

PRINTED CIRCUIT BOARD: THEORY OF OPERATION AND SERVICING ...

2.1 Introduction

2.2 Power Supply and Buffered Start

2.3. Oscillator

2.4 Electronic Latch

2.5 Credit and Start Circuit

2.6 Synchronization and Blanking ...

2.7 Sound Circuitry... ccc cece etn ee een n eee nns 2.7.1 Screech Sound 2.7.2. Crash Sound 2.7.3 Engine Sound

2.8 Audio Amplifier ..... 0.0.00 ccc cece eee e ee tenn etna n nee e ee

2.9 Dynamics and Speed Control 2... 0... cece ccc ccc ee eee teens 2.9.1 Gas (Speed) Circuit 2.9.2 Brake Circuit 2.9.3 Speed Oscillator

2.10 VLG Signal... 6. cece cece ee ene nnn nee anne eee

2.17 T STOP Signal 0.0.0.0 ccc cece een een ee 212 LOB SIgNal oo 6.6 eee c cece cece cence ete ec eee cette nent en ened

2.13 RESET 7 Signal

2.14 Steering Control

2.15 Steering Encoder ...... 06. ccc cece cece een teen ttn ene

2.16 Crash and Playtime 1... 00.66. c ccc ccc tte eens

2.17. Track Selection ..

2.18 Memory Circuit

Page 7

Table of Contents

2.19 Window Concept ........0 cece eee e eect een e en ee eee e rene n en eee e ee ee ne ees 35

2.20 Introduction to Motion ..... 6.66. c cece cette teen teen ees 37

2.21 Horizontal COUN .2 0.0. cece eat eee na eee eee ine ent eee ee ey open 38

2.22 Vertical Car MOtiOn .... 0.62. ccc cece ete tte eens 38

2.23 Horizontal Car Motion ..... 0... ccc cece cece nee e ents 39

2.24 Car Display oo... cic cc cece ee cent e eee bene e tt tenet tnn ee eee 40

2.25 Race Track Display ....... 006 cece eee eee eee teenies 40

2.26 Time and Score Storage ..... 6.66 cence eet enna 41 Ill. SCHEMATICS, DRAWINGS AND PARTS LISTS ................000 cece eee 45

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9

l. GENERAL MAINTENANCE AND SERVICE

1.1 INTRODUCTION AND WARRANTY INFORMATION Le Mans is a race car video game. It simulates the experience of driving a high speed race car around constantly changing race tracks. All the machine controls (steering, gear shift, accelerator and brakes) behave like those of a real car.

The electronics of this game are solid state for long life and low maintenance. The mechanical assemblies (steering, gear shifter and pedals) have been modularly designed for easy removal and servicing.

However, as with all mechanical or electrical devices, there may be minor problems. /f the printed circuit board computer (PCB) fails within the warranty period, contact the distributor from whom the game was originally purchased for repair or replacement instructions.

Any PCB repair attempted by anyone other than authorized Atari Service Center personnel will void the PCB warranty.

For the Atari warranty on the Le Mans game, please see the inside front cover of this manual.

1.2 ACCESS AND BASIC CONSTRUCTION Three openings: Coin door, rear door and a removable front control panel—provide convenient access to all sub-assemblies and adjustment points. Opening the coin door exposes all the coin handling equipment—the coin acceptors and rejector linkages, the coin counter and the coin box. The rear door is used to service the TV monitor, the PCB in the RF-shielded box, and the components mounted to the electronics tray—the transformers, fuses, etc.

A pair of interlock switches is mounted to the electronics tray and turns off the entire machine when the rear door is opened. Each switch in the Pair shuts off a “hot” lead in the AC line. The interlock switches protect the operator from accidental shock, so they must always be kept in perfect working order. \f you need to test or adjust the machine with the rear door open, place the interlock switches in the closed or ‘‘on’”’ position by pulling out the white actuator shaft.

All the major sub-assemblies have been designed modularly for easy servicing or replacement. The control panel, the pedal assembly, the PCB and the TV monitor can each be removed after the wiring and the release bolts have been removed.

1.3 NEW MACHINE SET-UP AND CHECK- OUT PROCEDURES Before turning this machine on, inspect it carefully for any damage which may have occutred during shipping.

As each new Le Mans leaves the factory, every component and sub-assembly is carefully checked for proper operation and adjustment. However, since parts may have been damaged or adjustments changed during shipping, the following checkout procedure must be repeated prior to placing the machine on location.

  • With the machine unplugged, open both access doors and carefully inspect both the exterior and interior of the machine for any obvious shipping damage to the cabinet or internal components and sub-assemblies. If any such damage is discovered, contact the carrier and Atari, Inc. immediately. Then contact the distributor from whom the game was originally purchased for repair or replacement instructions.
  • Inspect the interior of the machine more carefully ooking for broken or disconnected wires, subassemblies pulling loose or not firmly mounted and any foreign objects shorting electrical connections. Pay particular attention to the connections to the TV monitor, the control panel and the coin door. Also make sure that the PCB edge connector and the fuse are firmly seated.
  • Plug in the machine and if the rear door panel is off, defeat the interlock switch by pulling out the white actuator shaft. At this point the CRT (cathode ray tube) should display the race track and the score after a short warm up time. Examine the CRT picture. It should be steady, sharp and exhibit the proper levels of brightness and contrast.
Page 10
  • Insert several old and new coins into each coin acceptor. No genuine coin should be rejected. Pressing the game credit switch (start switch) advances the coin counter one digit. Operate both coin rejector handles and check for any signs of binding or sticking. Finally, check to see that both acceptors are firmly mounted in their frames.
NOTE

Lightly spray both coin acceptors and both sets of rejector linkages with WD- 40", a spray lubricant. This bit of preventative maintenance may save a service call later.

  • Start a game by pressing the start switch button and check for proper game sequence making sure all aspects of the game (steering, gear shifter, accelerator, brakes, score, timer and changing track display) are functioning correctly. If you are not familiar with the game sequence for Le Mans, read the game sequence analysis.
  • Adjusting play time modifies crash mode. The play time is pre-set at the factory for approximately 1 minute 40 seconds, and should not be changed.
  • Both doors (rear and cash) should open and close without binding, and both door locks should turn to the “locked” and “unlocked” positions freely.
  • Check the rear door interlock switch to see that it turns off the machine when the door is opened.

1.4 GAME SEQUENCE With the game plugged in and the rear door installed, the CRT will display the attract mode. The attract mode for Le Mans displays the race courses and a stationary race car positioned where the last player ended, plus the score of the previous game and the game timer (which should read 0). At this point, the play mode starts: the score is reset to 0, the timer begins counting down from 78 by twos, the car engine begins idling and is ready to be driven.

The controls of the machine and the movement of the car image simulate those of a real car. Once accelerated, the car becomes increasingly difficult to stop the faster the car is moving.

Turning the steering wheel causes the car to turn in the direction of rotation. The car will turn only while the steering wheel is being rotated.

The gear shifter works exactly like that of a real car. After a crash, shift into first, rotate the steering wheel to turn the car so it will continue in the proper direction and step on the accelerator pedal. Once the engine has revved to its limit, shift into second; when the engine has revved to its limit, shift into third and then fourth. The speed of the car will climb as you shift through the gears. Keep in mind, though, that the engine will “bog down” if you shift up too fast or start out in the wrong gear (2nd or 3rd).

Both the accelerator and brakes have only two positions: on or off. When the accelerator is depressed, the engine will rev up. Stepping on the brake pedal will bring the car to a screeching halt and if the steering wheel is turned as the brakes are applied, the car will skid realistically.

Points are scored only by passing the course check points in the proper sequence as indicated by the arrows on the CRT. The score is displayed at the top next to the game timer.

If the car is driven into any of the pylons, a crash will result. The crash is accompanied by a crash sound, uncontrolled spinning of the car during which time the car cannot be driven. As soon as the crash sound has ended, shift into first and continue driving the car in the proper direction. The game continues in this fashion until the game timer reaches 0 at which point the controls become “dead” and the machine is reset to the attract mode.

Players are given an indication of their skill by matching their score (points) against the ‘rating card” located on the game. This rating system is based on a game playtime of approximately one minute and forty seconds (as adjusted prior to shipment). If game playtime is readjusted by the operator, this point/rating system is no longer valid.

1.5 ANTENNA WIRE AND ANTI-STATIC MODIFICATION An electronic latch circuit has been incorporated in the Le Mans PCB. One function of this circuit is to turn off or prevent game credit if a player tries to obtain free games by inducing a static charge in the machine. The antenna wire is an integral part of this system.

When a static discharge occurs, an electric current is induced in the antenna wire. This impulse is transmitted through the antenna wire to the electronic latch circuit which turns off game credit and resets the computer to the attract mode.

Page 11

The antenna wire is a length of wire approximately 12 inches long. One end of the antenna is connected to pin K of the PCB edge connector and the other end has been intentionally left not connected,

The length of the antenna wire has been preadjusted by the factory to the overall optimum length, however some environments may require more or less critical adjustment.

Lengthening the antenna wire increases the sensitivity of the circuit; cutting the wire shorter decreases the sensitivity.

If players are obtaining free games by including static charges in the machine, lengthen the antenna wire (add a piece of wire) by a few inches so that a lesser charge will turn off game credit. If you have problems with static charges accidentally turning off game credit during the progress of a legitimate game, try cutting the antenna shorter in increments of 1-2 inches. Try to cut only the minimum amount off the antenna, otherwise players may be able to obtain free games.

The anti-static modification may be tested during a game by touching the end of the antenna wire with your finger as the body usually has enough capacitance to actuate the electronic latch. If the game is shut off, the circuit is functioning correctly.

1.6 TV AND LIGHTING: SERVICE PROCE- DURES Use the following procedures to replace the general illumination lamps, the plexiglass screen and bezel and to service the TV monitor.

1.6.1. General Illumination Lamps: A fluorescent 18-inch fixture is mounted behind the plexiglas screen to illuminate the Le Mans display panel. To replace the burned-out tubes, reach in the rear door and unscrew the four lamp PC board mounting screws; unplug the two wires that are attached to it at plugs near the upper left inside area of the cabinet. Remove the pane! and replace burnedout lamps with the same size and type of tube. The two small bulbs for signalling extended play are type-GE47 lamps.

1.6.2 Plexiglas Screen: Use the above procedure to remove the lamps PCB. Then remove the three wing nuts and carriage bolts that hold down the upper aluminum plexiglas screen retainer. Lift out the plexiglas. 1.6.3 Bezel: Use the above two procedures to remove the plexiglas; the bezel will simply lift out.

1.6.4 TV Monitor Removal: To remove the entire TV monitor assembly, remove the four Phillips-head bolts and nuts found on the top of the monitor frame. Do not remove the aluminum angle brace at the bottom edge. Disconnect the electrical connector to the TV, and lift out the monitor very carefully. DISCHARGE THE SEC- OND ANODE BEFORE SERVICING.

1.6.5 TV Monitor Adjustment: The TV monitor and its adjustment controls function like any normal TV set with the exception of the sound which is adjusted on the PCB. The monitor is serviced through the rear door of the machine.

  • Brightness: Adjust the brightness before the contrast. Adjust so that the CRT background is as dark as possible.
  • Contrast: The contrast is adjusted so that the CRT images are as bright as possible against the pre-adjusted dark background without being blurred.
  • Vertical Hold: Adjust only if the picture appears to be rolling up or down the screen, Adjust for a stable centered picture.
  • Horizontal Hold: Adjust if the picture is slightly off center horizontally, if the images appear warped or if the picture is broken into a series of diagonal lines.
  • Vertical Size: Adjust only if the top and bottom of the race course is cut off from the screen or if there is too much distance between the edge of the course and the edge of the screen, which will appear as an extra set of horizontal dotted lines on the top and bottom of the CRT display. Adjust for maximum picture size.
  • Vertical Linearity: Change this adjustment only if the top of the picture seems compressed.
  • The Yoke: The yoke should never need adjustment unless the adjuster have been tampered with or the machine damaged. If yoke adjustment is indicated, adjust both yoke rings simultaneously for optimum centering of the race course on the CRT.
Page 12
  • The A.C, Voltage Switch: Set this switch to the 115 Volt position ('115" visible on the switch) if the machine is connected to a 115 volt source. The TV monitor will not function if this switch is misadjusted.
  • The TV Monitor Fuses: Two 6/10 Amp, 125 volt Slo-Blo fuses (313 3AG) protect the TV monitor from electrical overload. Replace blown fuses only with those which have the above rating.
NOTE

The TV is not fused by the fuse on the electronics tray.

1.7, COIN DOOR: SERVICE PROCEDURES All coin handling equipment is accessible through the front door. To collect the coins, open the door, remove the coin box and record the meter reading.

The Le Mans is equipped with two coin acceptor assemblies so the entire machine will not be out of service if one acceptor is malfunctioning.

Please keep in mind that proper adjustment and lubrication of the coin handling equipment will help minimize your service calls.

1.7.1 Door Lock: The lock cylinder can be withdrawn and replaced after the rear retaining nut and the lock cam are removed. If the coin door does not fit tightly or the lock does not turn freely, try bending the lock cam slightly with a pair of pliers.

NOTE

The lock cylinder should be lubricated once every three months or so with graphite or WD-40®.

1.7.2 Reject Linkage: A separate reject button operates the wiper lever of each coin acceptor. When this button is pushed in, the wiper lever of the coin acceptor is operated which should dislodge any coins’stuck”in the acceptor. The rejector button cannot be removed.

NOTE

Lubricate the rejector linkage with silicone grease when you receive the machine and thereafter at approximately six month intervals.

1.7.3. Coin Micro Switches: To remove a malfunctioning micro switch, unscrew the two retaining screws, record the wire positions and pull off the slip-on connectors.

1.7.4. Coin Acceptors: The coin acceptor can be removed for servicing after the retaining screw has been removed.

1.7.5 Acceptor Adjustment: All coin acceptors leave the factory adjusted for maximum performance. However, if more critical adjustments are necessary or if the unit has been completely disassembled for service, the following adjustment procedure is suggested:

(These tests and adjustments are performed with the accepter in a vertical position on a level surface in the rest position.)

  • Kicker and Separator
  • Set the unit with the back‘of the acceptor facing you in the test position.
  • Loosen the screws holding the kicker and the separator and move both the kicker and the separator as far to the right as they will go. Tighten the screws.
  • Insert several test coins (both old and new) and
note that some are returned by striking the separator.
  • Loosen the separator screw and move the separator a slight amount to the left. Tighten the screw.
  • Insert the test coins again and, if some of them are still returned, repeat Step #4 until all the coins are accepted.
  • Loosen the kicker screw and move the kicker as far to the left as it will go. Tighten the screw.
  • Insert the test coins and note that some are returned.
  • Loosen the kicker screw and move the kicker a slight amount to the right.
  • Insert the test coins again and, if some are still returned, repeat Step #8 until all the coins are accepted.
  • Be sure that both screws are tight after the adjustments have been made.
Page 13
  • The Magnet Gate
  • Set the acceptor with the front of the unit facing you in the test position.
  • Turn the magnet gate adjusting screw out (counterclockwise) until none of the coins will fit through.
  • With a coin resting in the coin entrance of the acceptor, turn the adjuster in (clockwise) until the coin barely passes through the magnet gate.
  • Test this adjustment using several other coins (both old and new) and, if any of them fail to pass through the magnet gate, repeat Step #3 until all of the coins are accepted.
  • Fix the magnet gate adjusting screw in this position by tightening down the magnet gate screw lock nut.

1.7.6 Acceptor Maintenance: Depending on the environment in which the acceptor is used, periodic preventitive maintenance should be performed.

The mainplate may be cleaned with any nonabrasive household cleaner. Rinse and dry thoroughly to remove deposits and film.

Remove all metal particles from the magnet by guiding the point of a screwdriver along the edges of the magnet.

Remove the transfer cradle and clean the bushing and pivot pin. A pipe cleaner is an effective cleaning tool. Apply powdered graphite or pencil lead to the pin and bushing and reassemble.

Spray the entire unit lightly with WD-40® or a silicone lubricant.

1.8 ELECTRONICS TRAY SUBASSEMBLIES: SERVICE PROCEDURES (Pull out the power cord while performing procedures 1-4.)

1.8.1. Fuse Replacement: Replace the bad fuse with a Slo-Blo fuse rated at same amperage, 125 volts (313 3AG).

1.8.2. Transformer Replacement: To remove a malfunctioning transformer remove the AC protective cover, record all wire colors and their positions, unsolder the wiring and unscrew the retaining screws.

NOTE

When installing the new transformer, be sure to reconnect the chassis ground wire (lugs fastened with wood screws that mount the transformers to the wood electronics tray).

1.8.3. Interlock Switches: To remove the switches, pull off each push-on connector, squeeze in side tabs on the switch and push it through the mounting bracket.

1.8.4 — Printed Circuit Board: To remove the PCB from the RF-shielded box, pull the board straight out.

CAUTION

PCBs are extremely fragile and require very careful handling.

1.8.5 PCB Adjustments:

  • Volume: This adjustment is made by a small blue trim pot marked ‘volume’ near PCB position B9. Adjust the volume to the preference of the location but keep in mind that the machine may sound louder with the door off.
  • Play Time: This is factory adjusted for the optimum time. In the case of repair or accidental misadjustment, the play time is adjusted as follows: turn the pot near position B8 clockwise (while facing the engraved arrow) to /engthen game time. This pot controls both the total game length and the crash time period. The play time counter (to the right of the lap score in the pit area) always begins counting down from 78 by twos. Adjusting the play time pot causes the game counter to count down slower or faster.
NOTE

Adjusting for a longer game will also increase the length of the crash time, and affect score interpretation per the “rating card’ posted on front of the CRT. Ninety seconds is the optimum adjustment. Shorter or longer play times will result in decreased revenue.

  • Extended Play Switch Adjustment:The extended play time high score rollover is operatorselectable at scores of 46, 50, 56, 60, 66, 70 or 76. See Region B2 on sheet 1 of the schematic for exact
Page 14

switch settings (the DIP switch is near location N1 on the printed circuit board). To disable extended play, place all switches off. Only one switch of the seven should be enabled at a time.

1.9 MECHANICAL CONTROLS: SERVICE PROCEDURES

1.9.1 Control Panel: To service the rear of the control panel, reach through the coin door and remove the four wing nuts behind the panel. The control panel can then be lifted out and away.

1.9.2 Gear Shifter Assembly: To remove gear shifter from the control panel, first open the control panel as per procedure #1. Then record the wire colors and their positions for later reference and pull off all the slip-on connectors to the shift switches. Shift assembly can be withdrawn through the front of the control panel after the four retaining screws have been removed.

To open the gear shifter assembly, remove the four machine screws while holding the housing halves together with your fingers. Split the housing halves carefully so internal paris will not spring out and become lost. With the housing halves separated, the gearshift rod, spring, ball, detent and switch actuators will all be accessible.

NOTE

When re-assembling the unit, lubricate the ball with a small amount of silicone grease, and be sure that you replace the housing screws the same way they came out.

1.9.3 Pedal Assembly: The pedal assembly must be removed to replace the brake and accelerator switches. Reach in the rear door and remove three wing nuts. From the front of the machine, grasp the protruding lip of the pedal assembly and pull out the entire unit. To replace pedals, remove the four pedal retaining screws and lift off pedal. To replace switches, reach through the bottom of the peda! box and remove the wires and the two screws. Be sure to record all wire colors and positions before removing them from the switches. 1.9.4 Steering Wheel Assembly: To service or remove steering wheel assembly, open the control panel as per procedure #1. To replace the wheel, remove the shaft end nut. Lift off the slotted tack ring and withdraw the steering wheel through the front of the control panel. If only the wheel needs replacement, remove the cap and the shaft. The cap will lift off when retaining screws are removed, and the shaft can be disassembled when retaining nut is removed.

NOTE

When reassembling the unit, lubricate the bearings with a small amount of silicone grease, When re-installing the shaft, be careful not to push out the rear bearing. Tighten shaft end nut.

To replace the steering assembly PCB, remove shaft end nut and tack ring. The PCB can be replaced after the retaining screws are removed.

To replace the steering wheel bushing assembly, use procedure 4 to remove the steering wheel, then remove the six retaining screws that hold the backing plate to the control panel. Withdraw the bushing assembly through the front of the panel.

1.10 REGULAR MACHINE MAINTENANCE Due to its solid-state circuitry, your game will require very little maintenance other than periodic cleaning, lubrication and TV monitor adjustment.

The cabinet and plexiglas screen may be cleaned with any non-abrasive household cleaner. The coin acceptors, rejector linkages and the lock cylinders should be lightly sprayed once every three months with WD-40® or a spray lubricant. The TV monitor is adjusted only if the CRT picture is distorted or if the contrast or brightness are out of adjustment.

1.11. TROUBLESHOOTING PROCEDURES The first step in any troubleshooting procedure is to correctly identify the observable symptoms of the malfunction. With these clues in mind, examine the areas of the machine which might cause these symptoms. It is helpful for troubleshooting purposes to isolate three areas:

1.11.1. TV Monitor: Many TV problems can be rectified with proper TV adjustment. However, if the problem persists or if the TV is undoubtedly malfunctioning, contact your distributor or remove the TV monitor and take it to a competent local TV repair shop. Complete TV

Page 15

monitor repair manuals are available from your distributor.

1.11.2 Printed Circuit Board: Most PCB repairs may not be within your scope. If you can positively determine that your PCB computer has failed, contact the distributor from whom you purchased the game for repair or replacement instructions. Please be aware that some symptoms which might appear as PCB malfunctions may be the result of improper TV monitor adjustment or misadjustment of the small blue trim pots located on the PCB. Do not attempt to repair the PCB yourself un- Jess you have been specifically instructed to do so by your distributor. To do otherwise will void your PCB warranty.

1.11.3. Wiring Harness: For troubleshooting purposes, the harness includes the line cord, the fuse, the A.C. line filter, the transformers, the interlock switch, the antenna wire, the start and coin switches, the steering assembly, the gear shifter, the pedal assembly, the PCB edge connector, the TV monitor, ‘the speaker and all the interconnecting lengths of wire. A wiring enclosure diagram of the wiring harness and associated components has been included at the end of this manual to aid in troubleshooting.

1.11.4 General Suggestions: Following are some specific instructions and suggestions for troubleshooting your LeMans. To perform even the most simple troubleshooting procedures, you must have a VOM (Volt-Ohmeter) and, if possible, a VTVM (Vacuum Tube Volt Meter) or digital voltmeter. It is also very helpful to have another LeMans game (oraspare TV monitor and PCB) available for substitution purposes.

For many problems, substitution may be the easiest way to troubleshoot the machine. For example, if you suspect a PCB malfunction, try substituting another and known-to-be-good PCB. If the malfunction disappears, the first PCB must have been cause. Conversely, if the malfunction persists, the cause of the malfunction must be located in either the TV or the harness.

The TV monitor can also be checked by substitution. Simply connect the game to a known-tobe-good monitor and if the malfunction is cleared up, the first monitor must have been the cause.

Harness must be checked by elimination. Substitute a known-to-be-good TV and PCB, and if the malfunction persists, the harness and associated mechanical or electronic equipment must be at fault.

1.11.5 TV Monitor Troubleshooting: Some typical TV problems are distorted display, raster only or no video at all.

If you do not have a raster (a raster is a lighted but blank TV screen with the brightness turned all the way up), begin checking the power supply to determine if the TV is getting power. If the general illumination lamps of the machine are lighted, at least you know that power is reaching the machine. If not, check your line cord, interlock switch, fuse, etc.

If it is A.C. powered, go around to the back of the machine and with the rear door open (and interlock switch defeated) listen for a hum emanating from the monitor. If there is a hum, the monitor is powered and you may have a defective CRT or similar problem. Another test (and one which can be performed ina noisy environment) is to measure the voltage between the TV fuses and ground. If your voltmeter reads 110 volts or more, you know the monitor is powered. If not, check the fuses, the TV connections and the harness to see why power is not reaching the monitor. If the TV is powered but still not functioning, check the TV AC voltage switch which should be set to the ‘115’ position (115” visible on the switch) if it is connected to a 110-volt line source.

If you have the correct voltage after the fuses, but the monitor still will not function, you have two choices: 1). Remove the monitor and take it to a specialist, or 2). turn to the TV schematic and start exploring the monitor with a VTVM and an oscilloscope.

lf you do have a raster, you must determine why there are no video signals being displayed on the screen. These video signals are generated by the PCB computer and enter the monitor through pin 1 of the TV monitor connector.

1.11.6 | Steering Assembly Troubleshooting: Two small red LEDs have been included on the main PCB near position H68 to aid in troubleshooting the steering electronics.

Mounted on the small steering assembly PCB are two phototransistors and two infrared lightemitting diodes. The phototransistors are mounted behind the tack ring in such a way that the slots in

Page 16

the wheel break up the light emitted from the diodes. This generates pulses which are used by the computer to determine how quickly and in which direction the wheel is being turned.

The test LEDs on the main PCB will light whenever the infrared diodes are stimulating the phototransistors (i.e., whenever the diodes are shining through the slots in the slotted wheel onto the transistors).

To test the steering wheel assembly, simply rotate the whee! slowly in both directions while watching the two red LEDs on the main PCB. If your steering assembly is alright, both LEDs will flicker. If both of the LEDs fail to light (or remain lit constantly) while wheel is being turned, you definitely have a malfunction before the main PCB, which may be either in the wiring harness or in the steering assembly PCB.

1.11.7 Troubleshooting by Symptom:

  • No Power: Check for correct line voltage and if O.K. then check the fuse on the electronics tray, interlock switch and the transformer primaries.
  • No TV Picture: Check for power as per procedure #1 (NO POWER) and if alright, check TV connector and TV fuses. Measure voltage at TV fuses (should be 110 VAC) and if alright, replace the TV monitor.
  • TV Raster Only: Check the harness and especially the PCB edge connector. If alright, check the TV as per the special test under “TV Monitor Troubleshooting.” Or check TV or PCB by substitution.

(dj TV Picture Rolls: Adjust the TV vertical hold and if the rolling persists, check the TV or the PCB by substitution.

  • TV Picture Is Wavy: Adjust the TV horizontal hold and if the problem persists, try replacing the transformer (in the TV monitor itself).
  • TV Picture Is Broken Into Diagonal Lines: Adjust the TV horizontal hold and if the problem persists, check the TV or the PCB by substitution.
  • No Game Start: Check the coin switches, the start switch, the harness and replace the PCB if necessary.
  • Game Shuts Off Accidentally: Try cutting the antenna wire shorter in increments of 1-2 inches.
  • Picture Shrinks: Check the line voltage with your VOM and be aware that a large motor starting up (i.e., an air conditioner) may drop the line voltage. Check to see that machine is firmly plugged in. If the problem only occurs at certain times of the day (especially at dusk), your trunk line voltage may be dropping.
  • No Audio: Check the voiume control, speaker connections and for 20 volts. If the problem persists, test the speaker, and if the speaker is alright, try replacing the PCB.
  • Game Sequence incorrect, Parts of Race Course, Car, Score or Timer Missing or Distorted: Replace the PCB or check for proper power supply.
  • Car Will Not Steer or Turn in One Direction Only: Check PCB LEDs as Subparagraph 1.11.6 and if alright, then replace the PCB computer. If LED test is alright, check steering harness and connections and for foreign matter in steering assembly. Repiace steering PCB if necessary.
  • No Brakes: Check brake switch and wires from brake pedal switch to PCB. If alright, replace the PCB.
  • Brakes All The Time: Check brake switch for foreign material and/or shorting terminals.
  • No Accelerator: Follow procedure n for ‘’No Brakes.””
  • Accelerator All The Time: Follow procedure
  • All Four Gears Dead: Check connections and wires from gearshifter to PCB and if alright, replace the PCB.
  • One, Two, Three or Four Gears Dead: Check the connections and harness of the malfunctioning gear(s): check the shift switch(s) for the malfunctioning gear(s). [f problem persists, replace the PCB.
Page 17

ll. PRINTED CIRCUIT BOARD: THEORY OF

OPERATION AND SERVICING

2.1 INTRODUCTION Le Mans is a fairly complex video game, and the operation of the circuitry must be learned before your troubleshooting attempts will be successful. However, after the basic differences are understood, it should prove no more difficult than any other Atari PCB.

The main differences between Le Mans and previous Atari games are the steering circuitry, the ROMs and the power supply.

The steering circuitry is a novel bit of engineering which employs phototransistors and infrared light-emitting diodes to generate pulses indicating the direction of steering wheel rotation. Fortunately, it is quite a simple circuit and easy to troubleshoot.

The ROMs are other chips which has been specially programmed for Le Mans and it is used to generate the information for displaying of the car, score, game timer, and race tracks.Troubleshooting the ROMs is probably one of the easiest tasks because it involves only unplugging the suspected chip and replacing it with a known-to-be-good ROM.

The power supply is more complicated because additional voltages are needed to operate the ROM, the hybrids and the on-board audio amplifier. Even though there are a few more voltages to check, the basic power supply troubleshooting methods remain unchanged.

Because of this new circuitry, more test equipment is required to check the PCB. An oscilloscope is an absolute necessity and a logic comparator would be a wise investment.

2.1.1 Test Equipment Some of the following instruments are absolutely essential to fully test the PCB; others are desirable because they make the test procedures easier, but are not essential. Many of these items are available from the Atari Customer Service Department, 2175 Martin Ave., Santa Clara, CA 95050, and ‘hese items are indicated by an asterisk. A few others are available only from electronics supply houses or rental agencies; however, if you have difficulty in obtaining any needed instrument, contact our Customer Service Department for assistance

  • Required Equipment:
  • LOGIC PROBE*: The logic probe is an instrument designed for checking the outputs of integrated circuits. We recommend the Kurz-Kasch Logic Probe, model #LP-520. The logic probe will indicate if a signal is a logic high, low or changing from one state to the other. Consult the operating instructions included with the unit for further details on its operation.
  • VIDEO PROBE: The video probe is a simple, but useful, testing device. It consists of two IC test clips (or one clip and a test prod), a length of wire and a 4.7K, %4-W carbon resistor. Video probes can be assembled from standard parts available atany electronics supply house.

To use the video probe, attach one clip to the negative side of the video coupling capacitor (C44) and clip or touch the other end to the desired signal test points as indicated in the tollow. ing pages. The VP will display the signal directly on the CRT.

  • OSCILLOSCOPE: The oscilloscope is used for viewing various waveforms. Our application requires at least a 50-MHz scope and we recommend using a dual trace unit to facilitate comparison between waveforms. Our specific recormmendation is the Tektronix model #465, 100-MHz dual trace oscilloscope.
  • THE TEST FIXTURE: Le Mans test fixtures are available from the Atari Customer Service Department. You may wish to fabricate your own unit. This should not prove too difficult and will familiarize you with how the machine is built. You will need aTV monitor, transformers, an AC line filter, a steering assembly, a gearshifter, a few momentary contact switches and a PCB edge connector. Use the push button switches to replace the coin, gas and brake switches in order to reduce the size of the unit. Follow the plan of the wiring harness schematic and the enclosure wiring diagram when assembling the components.
Page 18
  • Optional Equipment:
  • THE LOGIC COMPARATOR®*: This compact troubleshooting instrument will prove invaluable in verifying correct IC operation. The unit simply clips onto in-circuit ICs and instantly displays any logic state difference between the in-circuit test IC and the reference IC in the comparator. Logic differences are identified to the specific pin by a lighted LED. If this instrument is purchased from the Atari Customer Service Department, it will be shipped with 20 pre-programmed reference boards. If the instrument is purchased elsewhere, you will have to program the boards yourself. We recommend either the HP 10529A comparator or the Fluke comparator.
  • THE LOGIC PULSER*: The logic pulser is used to stimulate in-circuit ICs so they are driven to their opposite states and we recommend the HP 10526T pulser. 2.1.2 Troubleshooting Suggestions The first step in the troubleshooting process is to correctly identify the observable symptoms of the malfunction and then to narrow down the possibly malfunctioning areas as much as you can. This should reduce the situation to one or two functional blocks which might be at fault. Then start examining these functional blocks with your test instruments and compare the results with the operational analysis and test point information under the heading of that functional block.

Keep in mind, however, that the first observable symptoms of a malfunction are not necessarily due to the functional block which produced those symptoms. A failure in one part of the PCB may affect much—if not all—of the PCB.

Some malfunctions may produce symptoms which are not clearly attributable to one component. Sync problems can be especially nasty in this regard because you can spend quite some time verifying the presence of correct sync signals on the board only to discover it is the monitor which is distorting sync.

This brings us to another subject: substitution as a troubleshooting technique. For instance, to clearly identify which component is at fault in a sync problem, try substituting a known-to-be-good TV monitor. If you have built a test fixture, plug the suspected board into the fixture and if the sync problem disappears, the other TV must have been the cause. Conversely, had the problem not disappeared, the substitution test would have revealed a malfunctioning board and you would begin the troubleshooting process at the sync section.

The same technique can be used to test the ROM which is inserted in a plug-in type receptacle to facilitate the substitution test. If you have a problem with the car image, the race track display or the score or timer displays, try inserting another and known-to-be-good ROM and if this clears up the malfunction, leave it there. However, we must note that the ROM failure rate has been extremely low, so it is more likely that a display problem is located in either the ROM address circuitry or the display circuits.

There are a few other problems which need mentioning because, while they may at first appear to be board-related, closer examination will reveal they are location-related.

If the line voltage fluctuates enough, the electronic latch will turn off game credit. One cause of this may be a large load connected to the same line as the machine. For example, a large air conditioner while starting up may drop the line voltage enough to break the electronic latch. Another cause may be that the line voltage drops at certain peak times of the day, such as dusk.

The location power supply is suspect in any malfunction which occurs on an intermittent basis.

Another game credit problem which may be either constant or intermittent in nature is a maladjusted antenna wire. The antenna wire is connected to the electronic latch and if the wire is too long, game credit may be accidentally turned off, especially if the machine is in a carpeted location. For more information on the antenna’s functions, see Paragraph 1.5 in Section | of this manual.

2.2 POWER SUPPLY AND BUFFERED START +5 volts is used to power most of the ICs; however, the ROM requires —12 volts, and the dynamics and sound require —5 volts, +5 volts, +12 volts, and —12 volts. The +18 volt source is used only to drive the audio amplifier. A separate +5 volt regulator is used for the video output circuit. The four circuits which generate the different voltages are very similar, as you will see. First, the 110 VAC line voltage is stepped down by the transformer(s) to 32 VAC and 16 VAC. These secondary voltages are then processed by the on-board power supply components to create the following voltages:

Page 19

+5 Volts: To create the regulated +5 volts needed by the ICs (and other components as well), the AC waveform at edge-connector pins 2 and B (16 volts) is full-wave rectified by diodes CR4 and CR5. The resulting DC voltage is then filtered by capacitor C4 and then regulated to a constant +5 volts by the LM309 voltage regulator.

+18 Volts: The AC waveform at pins 3 and C (32 volts) is rectified by CR7 and CR9, filtered by C49 dropped 2.1V, and taken directly to the audio amplifier.

—12Volts: Because the cathodes of CR6 and CR8 are wired to the transformer secondary, the resulting voltage will be negative with respect to ground. This waveform is filtered by C15 and then lowered to —12 volts by R19. The resulting voltage is regulated by a —12V three terminal regulator.

—5V, —12V, +5V Video: These all use three terminal regulators.

The Pull-Up Resistors: The pull-up resistors (R6, R15, R69, etc., and denoted by the schematic symbol “P’) are used to provide a logic high source for inputs to ICs which need to be tied high. The resistor limits the total current drain through the LM309.

Buffered Start: In order to prevent a high and possibly destructive inductive kickback when the coil of the game counter is de-energized, a buffered start circuit has been incorporated so that the game counter is now tripped by a silicon-controlled rectifier (MCR 106-1).

The coin switch NC contact is connected to the gate input of the rectifier. When the signal goes high, the silicon-controlled rectifier conducts, thereby energizing the coil of the game counter. On the next half-cycle of the AC current, the rectifier is shut off by the AC waveform and the coin is de-energized.

POWER SUPPLY TEST POINTS

TP 1: OSCILLOSCOPE: 32 VAC VOMIVTVM: 32 VAC

NDEO | +SXTO VIDEO yale [2 ‘Gud, Goreut tae) Ou -+18v 1P iw4o0t 3

  • ev | t sev

o>

Figure 2-1 = indoor tev (¥) 2A > ofesy 3A ya « (Pe

tyaoo! Lite Se 6) ~1zv 2 savor qty Lay

Power Supply and Buffered Start

W

Page 20

TP 2: OSCILLOSCOPE: 16 VAC VOMI/VTVM: 16 VAC

TP 3: OSCILLOSCOPE: +18 VDC VOM/VTVM: +18 VDC

TP 4: OSCILLOSCOPE: 8.5 VDC VOMIVTVM: 8.5 VDC

TP 5: LOGIC PROBE: High OSCILLOSCOPE: +5 VDC VOMIVTVM: +5 VDC

TP 6: OSCILLOSCOPE: —18 VDC VOMIVTVM: —18 VDC

TP 7: OSCILLOSCOPE: —12 VDC VOM/VIVM: —12 VDC

TP 8: OSCILLOSCOPE: —5 VDC VOMIVTIVM: -5 VDC

TP 9: LOGIC PROBE: High pulse when the start switch is operated. OSCILLOSCOPE: High pulse when the start switch is operated.

OSCILLATOR TEST POINTS

TP 12: LOGIC PROBE: High, low and pulsing. OSCILLOSCOPE: 14-MHz sine wave.

TP 13: LOGIC PROBE: High, low and pulsing. OSCILLOSCOPE: Same as TP 12, except out of phase.

2.3. OSCILLATOR Since the operation of the computer is synchronous, it requires a master timing signal which is provided by the oscillator and known as the clock.

The crystal oscillator generates a 14,318-MHz frequency and it is kept oscillating by two “closed foop” amplifiers which consist of a 330-ohm, ¥%-watt feedback resistor and an inverter. These amplifiers are coupled together by a .1yf capacitor (C46), and they operate out of phase with respect to each other. Inverter A8 pins 3 and 4 is used as a bufferamplifier; inverters A8 pins 5 and 6 and A8 pins 8 and 9 expand the oscillator’s loading capacity.

Figure 2-2 Oscillator

2.4 ELECTRONIC LATCH The electronic latch permits the starting of a new game when the coin is deposited and prevents the start of a game if the player attempts to obtain free game credit by inducing a static charge in the machine.

The control of game credit is accomplished by the presetting of the attract flip-flop C7 (see Paragraph 2.5 in this manual}. Whenever the output of the latch circuit—signal Q—is high, the attract signal will also be high. If the attract signal goes high, the computer is reset back to the attract mode and the game ends. In order for the game to begin, the electronic latch must be “latched’’ and signal Q must be high.

The latch cycle is started when COIN (the normally high output of the credit circuit) goes low as the coin is deposited. This low takes the base of transistor Q6 low, which causes the collector of that transistor to go high. Q6 then conducts that voltage and biases the base of Q8, allowing Q8 to conduct the low from its emitter to its collector. Since the collector of Q8 is tied to COIN, it keeps the latch circuit low even after COIN returns high as the coin switch is released. The circuit is now said to be “latched” and will remain in the latched condition until shut off by a low R signal or a high antenna signal.

Page 21

Ris the credit signai from B7 pin 6 in the credit circuit. A low R drags the base of Qé low, and since Q6 can no longer conduct, the latch cycle is broken. This toggles the attract flip-flop and resets the computer to the attract mode.

The same type of process is used to prevent players from gaining free game credit by inducing a static charge in the machine. When a latge enough static charge is discharged to the machine, the antenna wire picks up the necessary current to create a high at the base of Q7. This causes the low at the emitter to be conducted to the collector. Since the collector is connected to the base of Q8, a low Q7 collector will prevent Q8 from conducting and will break the latch cycle.

ELECTRONIC LATCH TEST POINTS

TP 14: LOGIC PROBE: High going low when coin switch is operated. OSCILLOSCOPE: Same as Logic Probe. TP 15: LOGIC PROBE: High during game and low at game over. OSCILLOSCOPE: Same as Logic Probe.

TP 16: OSCILLOSCOPE: + 5 volts until coin switch is operated; then drops to approximately +4 volts.

TP 17: OSCILLOSCOPE: 0 volts until coin switch is operated, at which time it rises to +.8 volts and remains there until game over.

TP 18: LOGIC PROBE: High during game mode; low during attract mode. OSCILLOSCOPE: Same as Logic Probe.

2.5 CREDIT AND START CIRCUIT The credit portion of this circuit records the deposit of the coin and lights the credit lamp. This provides game credit to the start circuit which is

RTO B7 PING (CREDIT CIRCUIT) +5V

TOC7PIN 4 (CREDIT CIRCUIT)

COIN FROM B7 PIN 1 (CREDIT CIRCUIT)

Figure 2-3 Electronic Latch

Page 22

Figure 2-4 Credit and Start Circuit 512V

from J2 pin 9

(syne circuit) a

latch circuit

-lefo] [als ¢|

(Only one score

enabled at a time)

pee EDS SNe Bren le fom ere deo” ol So pos ROLLOVER. + [ ate ~ = — lO] staat

EXT. PAY Saag

  • 220 wceIOe-t

Bok Fas, ee Q from electronic

Page 23

operated by the player to reset the PCB and begin the new game.

The deposited coin closes the normally-open side of the coin micro-switch, and the outputs of this switch are inverted by a “‘debouncing circuit” consisting of the two B6 inverters. The debouncing circuit eliminates undesired impulses created by the chattering of the coin switch contacts.

The debouncing circuit outputs enter the clear inputs of flip-flops A7. These two flip-flops constitute an anti-cheat device, designed so that incidental or player-induced vibrations that may operate the coin switch trip wire will not produce game credit. In order to get the correct outputs from the A7 flipflops, the coin switch contacts must mate for at least 128 horizontal sync pulses, or 8.12 ms. Since most incidental or play-induced vibrations produce a coin switch mating of only a few hundred microseconds, the Q outputs of the flip-fiops will not go high and no game credit will result.

However, if a coin is deposited, both A7 flipflops are enabled, and when both of the Q outputs are high, pin 3 of AND gate A6 will also go high. This produces a low at pin 10 of inverter B6, clearing the second B7 flip-flop.

The same signal which cleared the B7 flip-flops (COIN) also drags the collector of transistor Q8 low and turns on the electronic latch (see Paragraph 2.4 in this manual), enabling the attract flip-flop C7 at pin 4.

Since the credit lamp must be lighted to enable gate C6, and since C6 enables the start flip-flop C7, the game cannot be started unless the credit lamp is lighted.

When the start switch is operated, pin 12 of AND gate A6 is pulled high by its 1K pull-up resistor. Since the attract line (A6 pin 13) is already high, pin 11 of A6 will go high. This produces a high at the D input of start flip-flop C7 at pin 12. Since the clock input of this flip-flop is connected to vertical sync at 512 vertical (J2 pin 9), the high at the D input will be clocked out 512V later and this is the start signal.

Meanwhile, START goes low and clears C7 at pin

  • This produces a low at the attract flip-flop output; it returns to shut off gate A6 at pin 13. thereby starting the game and locking out the start switch so the player cannot reset the computer during play and gain additional time. The COIN signal also sets the cross-coupled flipflopAt-10,enabling the extended play (only one extended play granted per coin). The player's score 1C-1G are applied to a 1-of-10 decoder, and the high score output is selected by the DIP switch. If the player reaches the selected score, EXT PLAY goes low, setting B7 pin 13. Further, the EXT PLAY signal sets the extended play latch.

The credit light is enabled by the first coin, termed CR. When extended play is reached, the credit LED is then flashed by the one-second pulse.

CREDIT AND START CIRCUIT TEST POINTS

TP 19: LOGIC PROBE: Low going high when the coin switch is operated. OSCILLOSCOPE: Same as logic probe.

TP 20: LOGIC PROBE: High before coin switch is operated and high, low and pulsing while switch is held in the operated position. OSCILLOSCOPE: High before coin switch is Operated and high with low-going pulses (frequency: 12.5 ms; duration: 4 ms) while coin switch is held in the operated position.

TP 21: LOGIC PROBE: Low before coin switch is operated and high thereafter until game over. OSCILLOSCOPE: Same as for logic probe.

TP 22: LOGIC PROBE: Low going high when coin switch is operated. OSCILLOSCOPE: Same as logic probe.

TP 23: LOGIC PROBE: High going low when the start switch is operated. Stays low during the game. OSCILLOSCOPE: Same as logic probe.

TP 24: LOGIC PROBE: Low and pulsing. OSCILLOSCOPE: Frequency: 16.66 ms; duration: 0.28 ms.

TP 25: LOGIC PROBE: High with a low going pulse when the start switch is operated. OSCILLOSCOPE: Same as logic probe, except note that the jowgoing pulse is about 15 ms.

Page 24

TP 26: LOGIC PROBE: High during attract mode and tow during game mode. OSCILLOSCOPE: Same as logic probe.

TP 27: LOGIC PROBE: Low when player score matches extended play score.

TP 28: LOGIC PROBE: Low when no credit. High when credit, but not in extended play. Flashing when extended play score is reached.

2.6 SYNCHRONIZATION AND BLANKING A complex system of synchronization is required so the video signals generated by the PCB computer modulate the electron beam when the beam is in the correct part of the CRT. The essence of synchronization is timing. When sync is malfunctioning, the images appear to shift and move about the CRT because they are displayed in a different place each frame.

The PCB signals must synchronize with the electron beam horizontally so that the information on each line is displayed in the proper sequence (and also vertically so that the vertical positioning of the images is correct).

The sync pulses “tell” the electron beam when to start and stop its sweep, but do not otherwise control the raster. The sync circuit signals are also used in many other places in the PCB to time other operations with the TV monitor.

The basic timing for the horizontal sync circuit is the clock frequency. Vertical sync, however, runs off of horizontal sync. The horizontal and vertical sync counters count down the clock pulses to form timed pulse trains (see Figure 2-5).

The electron beam begins its sweep when horizontal sync goes low; this occurs after 902 clock pulses are counted out by the horizontal sync counters. The rising edge of the next H SYNC pulse occurs when the electron beam reaches the righthand side of the CRT, and the beam is reset back to the left-hand side by the monitor.

H RESET resets the sync counters after 451 clock pulses or counts. This is the end of the half line segment, so the counters must be started again. Horizontal blanking (H BLANK) is initiated by H RESET and lasts for 32 clock pulses. During the H BLANK time following H SYNC (every other H BLANk), information to be displayed in the next line is loaded into many parts of the PCB. The final horizontal sync signal (H SYNC) is composed of both H RESET and H BLANK and tells the electron beam when to start and stop its sweep.

Vertical reset serves the same purpose as H RE- SET, except it occurs after 521 horizontal blanking pulses (or half lines) when the electron beam is in the lower right-hand corner of the CRT. The V BLANK signal turns off the video during vertical retrace of the monitor. The vertical sync signal serves the same purpose as H SYNC, except it is timed to the vertical operation of the monitor.

The sync signals are generated in the following manner: the clock starts L2 counting, and when L2 reaches TC (terminal count), TC goes high and stays high for one clock pulse. Since TC of L2 is connected to CEP (count enable parallel) of K2, when TC of L2 goes high, k2 is advanced by one count by the clock pulse at pin 2. K2 then counts 15 clock pulses; then TC of K2 goes high (after a total of 255 clock pulses). The falling edge of the 256th clock pulse causes KT pin 3 to go high, and it will stay high until the 451st clock pulse when it is reset by H RESET. This 256H is divided again at K1 pin 5, producing the 512th clock pulse or count. This is the line that divides the CRT in half.

H RESET is an output of H1, and it is created by the addition of 256H, 128H, 64H and 2H. The result at J1 pin Bisa pulse 450 clock pulses from the last HRESET pulse. This is clocked through H1 by CLOCK, producing the H RESET signal.

Horizontal blanking is generated by H RESET, which presets the RS flip-flop composed of the F1 gates. This causes H BLANK to go high: 32 clock pulses later it resets the RS flip-flop, producing a blanking pulse 32 clock pulses wide after the H RESET pulse.

Horizontal blanking is then gated with H RESET and 512H to produce H SYNC.

Vertical reset is generated by horizontal blanking which clocks counter F2 at pin 14. The counter divides the clock frequency by 16 ; the output of this counter goes to H2, where it is again divided 16 times. The resulting signal is finally divided another four times by counter J2. J2 is allowed to divide only to four (a count of 512) because on the

Page 25

cLock (H BLANK) LIL Ll)

on]

2H (2v)

4H (av)

8H (sv) L

Figure 2-5 Sync Pulse Trains

521st count (512 plus 8V plus one more H RESET pulse) all the counters are reset by V RESET.

Vertical sync is created by the RS flip-flop F1, which is preset by V RESET and reset by 8V. This produces a high sync pulse which is four lines wide.

Because there are a n odd number of half-lines being counted out, the electron beam must start at the center of the top of the screen every other field to achieve vertical reset. the even field begins in This is why the first line of the center of the CRT.

SYNCHRONIZATION AND BLANKING TEST POINTS

TP 29: VIDEO PROBE:

LOGIC PROBE: OSCILLOSCOPE:

VIDEO PROBE: LOGIC PROBE: OSCILLOSCOPE: TP 29: b

LOGIC PROBE: OSCILLOSCOPE:

TP 30: VIDEO PROBE:

LOGIC PROBE: A number of thin vertical white lines. Low and pulsing. Frequency: 1.12 us; duration: 0.07 ms.

Two vertical white banks. Low and pulsing. Frequency: 32 ws: duration: 1.3 ws.

Alternating black and white bands. High, low and pulsing. Frequency: 32 us; duration: 14 ws.

Left half of CRT black; right half white. High, low and pulsing. Frequency: 64 ys; duration: 28 us. TP 31:

TP 32:

TP 33:

TP 34:

TP 35:

TP 36:

TP 37:

TP 38: VIDEO PROBE:

LOGIC PROBE: OSCILLOSCOPE:

VIDEO PROBE:

LOGIC PROBE: OSCILLOSCOPE:

VIDEO PROBE:

LOGIC PROBE: OSCILLOSCOPE:

LOGIC PROBE: OSCILLOSCOPE:

VIDEO PROBE:

LOGIC PROBE: OSCILLOSCOPE:

LOGIC PROBE: OSCILLOSCOPE:

LOGIC PROBE: OSCILLOSCOPE: One thin vertical black line in center of CRT. High and pulsing. Frequency: 32 ys, duration: 0.1 ws.

Thin vertical white line in center of CRT. Low and pulsing. Frequency: 32 ws; duration: 0.1 ws.

White vertical center of CRT. Low and pulsing. Frequency: 32 ys; duration 2.3 us. band in

High and pulsing. Frequency: 63.5 us; duration 2.3 us.

Starting with 2V, touch probe to all outputs up to 512V. Notice that the horizontal black and white bars double in width at each successive division,

Low and pulsing. Frequency: 16.66 ms; duration: 20 ys.

Low and pulsing. Frequency: 16.66 ms; duration: 30 ps.

Low and puising. Frequency: 16.66 ms, duration: 254 ys.

Page 26

Figure 2-6 Synchronization and Blanking —ASYRE Came SYNe

ate’ Parle 64 eee

‘7 RESET HBL

Page 27

2.7 SOUND CIRCUITRY The noise generator uses a 16-stage pseudorandom number generator. This number of stages gives a nonrepetitive count of 65,535 states, which very closely approximates white noise. One troublesome feature with this type of counter is that there is always one lock-up state in which the counter would stop. To prevent this from occurring, an inverter is placed in one of the feedback branches, so that the clear input on the shift registers will set the counter to an active state. When the clear is released, the counter starts from that state and generates its pseudorandom pattern. This part of the sound system is the heart of the screech and crash sounds.

2.7.1 Screech Sound: This sound is generated using a frequencymodulated oscillator. A 555 timer is used in the astable mode with the center frequency of ground 850 Hz. The output of the noise generator is fed into the FM input (pin 5) with the proper amplitude to simulate a screech sound.

The screech logic circuit generates the SCREECH signal, which creates the “screech” sound by enabling the noise and screech sound generator.

ATTRACT must be high (a game started) to enable the screech circuit. If SKID (the “brakes applied” signal) goes low presetting flip-flop C1, the SCREECH signal will go high. When SKID returns high, 1024V will be clocked through two frames later turning the SCREECH signal off. SCREECH LOGIC TEST POINTS

TP 39: LOGIC PROBE: High until brake switch is closed, then drops low. OSCILLOSCOPE: Same as logic probe.

TP 40:LOGIC PROBE: Low going high when brake switch is closed. Same as logic probe.

2.7.2 Crash Sound: To generate the crash sound, the output of the noise generator is modulated by a voltagecontrolled amplifier. The VCA used is a MFC6040 (or MC3340) which generates an envelope amplitude proportional to the voltage applied to the control pin. When a crash occurs, the voltage on the control goes toward ground very rapidly, turning on the VCA. When the crash signal is removed, the voltage on the control pin is allowed to come back up. This is caused by current from the control input flowing into a capacitor. The capacitor prevents the voltage from building up at once, at a rate set by the time constant of the circuit. This gives a decaying envelope to the sound which simulates a crash. The VCA also has a .01 ef capacitor on the rolloff terminal to filter out some of the high frequency components of the sound.

2.7.3 Engine Sound: This circuit creates the sounds of the car engine, both when it is idling and moving. This is accomplished with three function generators and one electronic attentuator.

CRASH SEQUENCE

SCREECH

SCREECH

Figure 2-7 Screech Logic

Page 28

J

‘MOTOR

Figure 2-8 Engine Sound Logic

Closing the gas pedal switch drops the RPM signal voltage from 0 volts to about —3 volts, causing the function generators to modulate the frequencies of their signals.

The sound signals from C8 and D8 are the inputs to the attenuator (F8), and the signal from #8 modulates the amplitude of the attenuator output. The resulting sound signal is carried to the audio amplifier and then to the speaker.

ENGINE SOUND GENERATOR TEST POINTS

TP 46: OSCILLOSCOPE: Closing the gas pedal (1st gear) switch causes the attenuated R.P.M. signal voltage to drop from 0 to —2.5 volts.

2.8 AUDIO AMPLIFIER An audio amplifier is necessary to drive the speaker. The sound signals enter the amp circuit through R16 and C8. The resistance of R4 determines the gain or volume and is adjusted by turning the small blue trim pot (marked ‘‘VOL") found near the LM380. The LM380 amplifies the sound signal to a level high enough to drive the speaker. Pin #1 is used to turn off the sound in the attract mode. When this pin is pulled low, the amplifier is disabled.

THE AUDIO AMPLIFIER TEST

TP 50: Turn the volume down, attach the clip end of a video probe to capacitor C8 and run the prod down the vertical sync counter outputs. You will hear a series of tones from counter H2 pins 12, 9, 8 and 11.

2.9 DYNAMICS AND SPEED CONTROL An analog computation circuit is used to take the gas and brake pedal inputs and convert them to the appropriate RPM and speed voltages used, respectively, in the motor sound circuit and the speed pulse oscillator.

2.9.1 Gas (Speed) Circuit: Figure 2-10 is a simplified drawing of the RPM and speed amplifiers. When the gas pedal is depressed, the input to the RPM amp rises to 2.5 volts (5 volts for 4th gear). This is amplified and inverted by the RPM amp; an input from the acceleration circuit prevents the output from going negative instantaneously as

Page 29

SCREECH

Aveo OUT

N PARENTHESIS.

Figure 2-9 Audio Amplifier

+5 +5

4th

FROM ACCELERATION/DECELERATION AMP

GAS

MAX. SPEED SPEED SWITCH VOLTAGE OUT

SPEED CAPACITOR

SPEED SWITCH COMPARATOR SPEED REFERENCE

3.3K

Figure 2-10 RPM and Speed Amplifiers

Page 30

ATK ACC/DEC

MAX. SPEED SWITCH + | SPEED CAP SPEED REF.

| GEAR SHIFT

Figure 2-11 explained later. When the RPM voltage goes negative, the 100 uf speed capacitor starts to charge in the negative direction. The capacitor voltage is buffered by the speed amp to provide the speed voltage out to the oscillator.

A speed reference signal is determined by the RPM voltage and the gear shift position. When the speed voltage reaches the speed reference, the speed switch comparator opens the max speed switch preventing the speed capacitor from charging further. The actual gear resistors are switched in remotely by analog switches.

The ACC/DEC circuit is shown in Fig. 2-11 above. When the gas pedal is pressed, the RPM voltage is coupled through the speed switch to the capacitor that begins to charge. The RPM voltage and the gear shift establish the speed ref voltage. The difference between the speed ref and speed voltages is obtained by the ACC/DEC amplifier. This difference is then fed back to the RPM amplifier to effectively limit the rate of RPM increase. When the car is at rest or at a constant velocity such as maximum speed in 1st, 2nd, or 3rd gear, the output of the ACC/DEC amp is zero and has no influence on the speed/RPM circuit. Acceleration/Deceleration Circuit

If the car is in motion and the gas is let up, then the speed reference signal immediately goes more positive than the speed voltage, causing the maximum speed switch to open and the ACC/DEC amplifier output to go positive. This positive voltage is fed into the RPM amp to keep the RPMs “up.” The positive voltage also causes current to flow through Ra and R, to charge the capacitor towards ground, thus reducing the speed (compression).

If an upshift or downshift is made while the car is in motion, the speed ref voltage will change instantly and cause the ACC/DEC voltage to go negative or positive, respectively. This, in turn, causes the RPM voltage to decrease or increase depending on the direction of the shift.

As an additional note, the speed switch comparator causes the maximum speed switch to be closed during acceleration, open during deceleration, and partially closed or slightly oscillating for constant speed.

  • RPM AMP Input/Output Conditions: The junction of the 4.7K and 100K resistors at the RPM AMP input is connected to the gas pedal switch that
Page 31

controls the acceleration of the car. When the car is stationary or in gear with no gas, this point will be zero volts. When you step on the gas, this will increase to approximately 2.5 volts in first, second, and third gears and rise to +5 volts in 4th.

The RPM output (TP 59) is at 0 volts when the gas switch is open, and drops to about — 3.6 volts when you step on the gas in first. When you shift into second, pin 3 rises to approximately —2 volts and then drops to about — 3.8 volts as the car picks up speed. The same occurs on a shift from 2nd to 3rd. When you shift into 4th, it rises to— 2 volts again and drops down to about — 4.4 volts when the car reaches maximum speed.

  • Speed AMP Voltages: The output of the speed amp is the analog of the car speed. This voltage starts at 0 volts and drops to ~ 0.65 volts at top speed in first gear. When you shift into second, it drops to about ~ 1.3 volts as the car picks up speed. When you shift into third, it drops to — 2 volts and then drops down to about — 3.5 volts when the car reaches maximum speed in 4th gear.

2.9.2 Brake Circuit: Fig. 2-12 is a simplified drawing of the brake circuit. When the brake is pressed, the PNP transistor is switched on, causing current to flow through R, to charge the speed cap towards 0 volts. The discharge current is sensed by the skid amplifier—whose output goes low upon braking. When the capacitor has charged to a point near zero, but the car is still slightly moving, the lbrake Current no longer causes sufficient voltage drop across Rp to overcome the slight bias introduced by Ry and the 1 Meg resistor. The SKID signal goes high, thus removing the SKID condition.

When SPEED KILL goes high,the speed cap is charged to 0 volts immediately to kill the car speed. The limiter amplifier and diode prevents the voltage on the speed capacitor from going positive.

2.9.3 Speed Oscillator: The speed oscillator is shown in Fig. 2-13. Assume that the timing capacitor has been charged through the diode and is now discharging through R,. When Veap reaches a voltage equal to Vin, Comp. B goes low to switch the flip-flop composed of cross-coupled gates. This in turn causes C, to recharge to a negative voltage through the diode. When Veap reaches Vrer, Comp. A goes low, resetting the flip-flop to allow C, to again charge towards 0 volts.

Figure 2-12 Brake Circuit

Page 32

in tos

(-4,1v)

SPEED PULSES Vint

SPEED PULSES Vin 2

10K

ct ZS +2 mytar 5 130K RT

Figure 2-13 Speed Oscillator and Waveforms

When Vi, is just slightly positive with respect to Vrer, Cr only discharges for a short period before it is again charged and the oscillator frequency is high. When Vin is just slightly negative, C,; must charge exponentially toward 0 volts until Vi; = Vian and the frequency is low (see Fig 2-13). When Vin #0, the oscillator is stopped. SPEED CONTROL TEST POINTS

NOTE

The easiest way to check many of these test points is with a digital voltmeter (DVM); however, the oscilloscope will yield accurate results also. In a pinch, use a VIVM.

Page 33

SPEED KILL

4K 1% WA)

(8)

SPeed Purses,

Figure 2-14 Speed Control

Page 34

Figure 2-14 Speed Control Audio Refile at 100A wot tev $ i HY y M3340 + @e] ZS meceoso PIN MS ON PACENTHESIS.

Page 35

TP 51: LOGIC PROBE: Low going high as each shift is closed. OSCILLOSCOPE: Same as logic probe.

TP 52: OSCILLOSCOPE: 0 volts, dropping to —5 volts when the brake switch is closed. DVM/VTVM: Same as oscilloscope.

(Note: voltages below refer to all three test points.)

Check voltage drop with the oscilloscope or voltmeter as you reach top speed in each gear. 1st gear 2nd gear 3rd gear 4th gear ..

TP 54: LOGIC PROBE: Low, going high when a crash occurs. OSCILLOSCOPE: 0 volts, rising to 3.5 volts at crash. DVM/VTIVM: Same as oscilloscope.

TP 56: LOGIC PROBE: High, going low when brake switch is closed (car in motion). OSCILLOSCOPE: Same as logic probe.

TP 57: OSCILLOSCOPE: 0 volts when car is at rest or constant speed. —0.8 volts when acceleration starts and +0.8 volts when deceleration starts (gears 1-3 only).

TP58: Check with oscilloscope or voltmeter. Voltage should increase from 0 volts to the indicated values as the gas pedal is depressed. Ist gear ... -+-+2.5 volts 2nd gear .+2.5 volts 3rd gear ...+2.5 volts 4th gear .. 2... eee +4.3 volts

TP59: Check with oscilloscope or voltmeter. Voltage should drop from 0 to the indicated values as you reach top speed in each gear. Ast Bear... eee cece ee eee —3.6 volts 2nd gear . - 73.7 volts 3rd gear —3.8 volts 4th gear .. - 4.3 volts

TP 60: LOGIC PROBE: Low when car is at rest; high when car crashes or when game is in attract mode. OSCILLOSCOPE: Same as logic probe.

NOTE

Speed oscillator input/output conditions: As speed voltage into the oscillator input (TP 61) drops lower and lower, the speed pulses from the 4011 output buffer (TP 62) increase in frequency.

TP 61: Check with oscilloscope or voltmeter. Voltages should drop from 0 volts to indicated values as you reach top speed in each gear. Ist gear ... 0.4 volts 2nd gear —0.9 volts 3rd gear —1.4 volts 4th gear . —2.6 volts Car at rest in any gear --+.08 volts

TP 62: LOGIC PROBE: Low when car at rest; low and pulsing when car is moving. OSCILLOSCOPE: Following readings are to be taken with car at top speed in each gear. Ist gear ........00. 65 ms between pulses 2nd gear . . -45 ms between pulses 3rd gear . 30 ms between pulses 4th gear ..15 ms between pulses

2.10 VLd1 SIGNAL VLd1 (‘vertical load one’’) is used to address the ready-only memory (ROM) for the vertical positioning of the car image.

V RESET clocks the low from B1 pin 12 out the Q output; this low waits at B1 pin 2 until it is clocked through by H SYNC. The Q output (B1 pin 5) presets B1 pin 10, causing a high to appear at B1 pin 9. This high is clocked through B1 pin 5 on the next H SYNC pulse. The result is a VLd1 pulse which occurs once per field and is one H SYNC pulse wide.

Page 36

2.11 1 STOP SIGNAL

This signal is a ROM address that determines the speed with which the car image is moved.

The input to this circuit is SPEED PULSE from pin 1 of the 8098 in the speed control circuit. As the car picks up speed, the speed pulses increase in frequency.

When the car is stationary, 1 STOP is low. As the car starts moving, 1 STOP begins pulsing high and the pulses get closer together and longer in duration until the car reaches top speed in fourth gear, at which time the signal stays high (see Figure 2-16).

TP 64: LOGIC PROBE: Low when car at rest. Figure 2-15 VLd1 Circuit Low and pulsing when car is accelerating. High when VLd1 TEST POINTS car reaches top speed in Ath gear (provided speed TP 63: LOGIC PROBE: Low and pulsing. pot is adjusted correctly). OSCILLOSCOPE: Frequency: 16.66 4s; dura- OSCILLOSCOPE: See waveform illustrated tion 63.5 us. above. [ |

woe LALLA

1_t__ — ey CAR NOT CAR PICKING CAR AT TOP MOVING UP SPEED SPEED

P Pp

ATRC

‘SPEED PULSE FROM ANALOG

vidi

Figure 2-16 1 STOP Waveform and Circuit

Page 37

16H

H SYNC

Figure 2-17

2.12 Ld1B SIGNAL Ld1B (“load one B”) is another ROM address; however, it is also used in several other places to load information into counters, etc.

H SYNC clears flip-flop D1. Sixteen clock pulses later, the high is clocked from the D input out the Q output and is inverted to become Ld1B. V SYNC disables this function once per field, producing a wider Ld1B pulse.

1d1B TEST POINTS

TP 65: LOGIC PROBE: Low and pulsing. OSCILLOSCOPE: Frequency: 63.5 4s; duration 5s.

2.13 RESET 1 SIGNAL The function of this signal is to tell the car motion circuits where to reposition the car image at the start of a new game or after the car is driven off the race course.

When CAR 1 VIDEO encounters COMP SYNC (i.e., the car is driven off the screen), A2 pin 6 goes low and causes a low to appear at A6 pin 5. The last low clears flip-flop A4. The flip-flop remains cleared until it receives the next VLd1 pulse which clocks the high from A4 pin 2 out A 4 pin 5: this signal is known as RESET 1.

START serves a function in the circuit similar to the low from A2 pin 6: it also clears RESET 1. 1Ld1B Circuit

RESET 1 TEST POINTS

TP 66: LOGIC PROBE: Low pulse when the game starts or the car is driven off the track. OSCILLOSCOPE: Same as logic probe.

2.14 STEERING CONTROL The two infrared light-emitting diodes (LEDs) mounted on the steering assembly PCB are aimed directly at the two phototransistors. As the slotted steering ring rotates, the path of light is broken up causing the phototransistors to pulse in a way which corresponds to the direction of the steering wheel rotation. These pulses are fed into four-input Schmitt triggers (J8) which clean up the pulses so the flip-flops can be triggered consistently.

When the steering wheel is turned in a clockwise direction, a rising edge occurs at the clock input of K8 before a rising edge reaches the D input. This causes the CW (clockwise) signal to be high, enabling gate A2 to advance the steering encoder (see next section of this manual); the steering encoder rotates the car in a clockwise direction.

However, if the steering wheel is rotated in a counterclockwise direction, a rising edge will occur at the D input before a rising edge reaches the clock input. This produces a low CW signal. The RATE signal triggers A4, providing a pulse to decoders A2 and A3. Depending on the direction

Page 38

CAR 1 VIDEO

COMP SYNC

START

Figure 2-18 RESET 1 Circuit

(CW or CCW), the car image direction counter is incremented or decremented. V RESET resets A4 and sets the maximum turning rate for the car—one step per frame.

During a crash, CRASH A goes low and presets K8, producing a low CW. It also presets A4, producing a high at A4 pin 9; this shuts off gate A3. This allows A3 to pass 128V, decrementing the encoder counters and thereby causing the car image to spin uncontrollably during the crash.

Two LEDs (CR17 and CR18) have been included on the main PCB to facilitate troubleshooting the steering assembly. The pulses from the Schmitt triggers light the LEDs. If the LEDs flicker as you rotate the steering wheel, the steering assembly components are probably alright and the malfunction is most likely located in another part of the steering circuitry. If the LEDs do not flicker, look for foreign material between the infrared LEDs and the phototransistors of the steering PCB, physical damage to the steering assembly, broken connections or a malfunctioning Schmitt trigger.

STEERING CONTROL TEST POINTS TP 67: LOGIC PROBE: High when steering wheel is turned clockwise. Low

aa TO J3 PIN 5: +165 UP STEERING nea ae ENCODER a

_ 3 | TOJ3 PIN4: ' 3 2)6 >] DOWN STEERING To n STEERING \ ' vey | ENCODER ' iS 1 & GAA | % : \ i ‘

\ te

Figure 2-19 Steering Control

Page 39

when steering wheel is turned counterclockwise. OSCILLOSCOPE: Same as logic probe.

TP 68: LOGIC PROBE:Pulseswhen _ steering

wheel is turned, and pulse rate rises as wheel is turned faster. OSCILLOSCOPE: Same as logic probe.

TP 69: LOGIC PROBE:Pulseswhensteering

wheel is turned clockwise. High when steering wheel is turned counterclockwise. OSCILLOSCOPE: Same as logic probe.

TP 70: LOGIC PROBE:Pulseswhensteering

wheel is turned counterclockwise. Low when steering wheel is turned clockwise. OSCILLOSCOPE: Same as logic probe.

TP 71: LOGIC PROBE: Pulses except when steering wheel is turned counterclockwise or when a crash occurs. OSCILLOSCOPE: Same as logic probe.

2.15 STEERING ENCODER The steering encoder directs the ROM to read out the different aspects of the car image as the steering wheel is rotated.

The steering control circuit decides whether to pulse the UP (“U” at J3 pin 5) or the DOWN (D” at }3 pin 4) line of the J3 up/down counter. As the up input is pulsed, a binary code results at output pins 6 and 7 of J3. After 16 pulses into the up input, a “carry” pulse is produced at J3 pin 12. This advances K3, which then produces another binary code at output pins 2, 3 and 6.

However, if the down input to J3 is pulsed, J3 will count down from the last loaded number and, when it reaches 0, a “borrow” pulse is generated at J3 pin 13, decrementing K3.

At the beginning of the game, or if the car is driven off the track, RESET 1 goes low. This resets the counters to zero and re-orients the car image. L3 is a latch which takes the 1D1, 1D2, 1D3 and 1D4 outputs from the counters and passes these signals on to the ROM multiplexers unless SCREECH is high. A high SCREECH latches up the last information from the counters and holds it until SCREECH goes low again. This causes the car image to continue moving in the same direction it was going when the brakes were applied, even if the steering wheel is turned which produces a realistic ‘’slide’” or “drift.”

STEERING ENCODER TEST POINTS

TP 72: LOGIC PROBE: Changes state twice for every complete car image revolution. OSCILLOSCOPE: Same as logic probe.

2.16 CRASH AND PLAYTIME This circuit has two functions: (1) it generates the crash signal when the car is driven into the pylons, and (2) it times the length of the game.

The 555 timer at B8 is the component that actually provides the timing. The amount of time it takes to charge C43 determines the pulse width out of the 555, and controls the period of time the output signal 1 SEC is high. R72 adjusts both the crash time period and the playtime by varying the amount of time required to charge the capacitor. The timer output is used to clear the crash flip-flops after a crash has occurred. It is also the input to the game timer circuit that turns the game off after it counts a certain number of 1 SEC pulses.

This circuit also generates the crash signal (CRASH A) whenever the car window encounters the race track signal by gating the two signals together at D5. A crash produces a low at D5 pin 3 that clears both B5 flip-flops. 2048V later, a low is clocked out of B5 pin 8. During the time this pin is high, flip-flop C5 is enabled and asks the question, Is there a car on the pylons?” If the answer is ‘no’ (i.e., one of the wheels has just barely glanced off a pylon), C5 continues to repeat the question until it is cleared at pin 13 by alow from B5 pin 8.

However, if the answer to C5’s question is “yes,” C5 pin 8 goes low, causing D5 pin 11 to go high. Then the “yes” information is latched into C5 at pin 5, producing a high at CRASH A and a low at

CRASH A. A low BRASH A produces a low SPEED Alow RETRACT will also produce a low SPEED KILLS

KILLS signal from D5 pin 8 that stops the car motion.

Page 40

SCREECH FROM ANALOG

1R3

1R2

1R1

1RO0

Figure 2-20 Steering Encoder

SPEED KILL

CRASH SEQUENCE

Figure 2-21 cae VIDEO

Car Crash and Playtime

Page 41

and stop the car whenever the computer is in the attract mode.

CRASH AND PLAYTIME TEST POINTS.

TP 74: LOGIC PROBE: High with low pulses approximately once per second when game is in the play mode. NOTE: Frequency of 1 SEC is adjustable by R72. OSCILLOSCOPE: Same as logic probe.

TP 75: LOGIC PROBE: Low going low when the car crashes. OSCILLOSCOPE: Same as logic probe.

TP 76: LOGIC PROBE: Drops low when the car encounters the race track. OSCILLOSCOPE: Same as logic probe.

TP 77: LOGIC PROBE: High pulse when the car crashes. OSCILLOSCOPE: Same as logic probe.

TP 78: LOGIC PROBE: Normally high, low and pulsing; changes to high when a crash occurs.

2.17 TRACK SELECTION On Le Mans, every time the player completes a lap a new track is displayed. Each track is more complex than the preceding track. The track select is TSA, TSB, and TSC. During the game mode, the track select is jammed set with the lap count from the score—1E, 1F, 1G, and 1J. During the attract mode, the 193 is no longer parallel loaded but is counting at a 4-second rate. The attract mode shows Le Mans stepping through the tracks.

On lap 7 and 8, either tracks 7 and 8 or tracks 9 or 10 are displayed. The flip-flop (see ROM select Page) picks up data from the 2-second timer to randomly display either tracks 7 and 8 or 9 and 10.

During extended play, the player starts with a score of zero, but play resumes on Track 5. Tracks 1-4 are the “learner” tracks and are not used for extended play. The cross-coupled 7400 gates force TSC high in the extended play mode.

2.18 MEMORY CIRCUIT This circuit stores information which is later read out for the generation of the car image, the race track display and the score and timer displays. +5V

Figure 2-22 Track Selection

The main components are four multiplexers and three 16K ROMs (read-only memories) that have been specially programmed for Le Mans.

The ROMs are memory units that store binary information. This information is read out of the ROMs by the multiplexers, and these outputs go to other circuits where the information is used to form the different aspects of the car image, the race track display, etc. The ROMs each store 2048 eight-bit words.

Multiplexers select certain signals from a larger input of signals, and these output signals are the “addresses” for the ROM. A different multiplexer address is required to read out each different eight-bit ROM word. For example, when information is needed for the generation of the car image,

Page 42

the multiplexers select the correct ROM address, and this selected signal reads out the desired car image information from the ROM. This ROM information is then fed into the car motion circuits, and a new aspect of the car image is displayed on the CRT.

{It is important to understand how the multiplexers function, so we have included a brief discussion of basic multiplexer operation. Figure 2-23 is the schematic of a basic two-input two-to-one data multiplexer.

> DATA SELECT

o OUTPUT

TRUTH TABLE

OUTPUT

Figure 2-23 Basic Two-Input Two-To-One Multiplexer

When the data select line (S) is high, the signal at the A input is reflected at the output. When S is low, signal B appears at the output. For instance, if signal A is high while $ is high, the output will also be high.

The multiplexers used to address the ROM are nothing more than elaborations on the foregoing theme. Figure 2-23 shows a two-input, two-to-one multiplexer; the ROM requires eight-input, fourto-one multiplexers.

The ROM itself is not a particularly complicated device; it is useful only because it can store so much information in a small space. Visualize the ROM as being constructed from 2048 rows of 8 diode gates each, where each gate is connected to one of the eight ROM outputs. Each diode in every row is specially programmed so that it reads out either a high or a low when it is addressed. Each row of eight gates must be addressed by a different binary number. When this number is read out by the multiplexers into the ROM address inputs, each diode in that row reads out its high or low to one of the ROM outputs. Troubleshooting the ROM Circuit: Some typical symptoms of malfunctions in this circuit are a distorted or missing car image, portions of the race track distorted or missing, or distortion of the lap counter or game timer displays.

If you suspect trouble in this section, the first step is to replace the appropriate ROM (see Table 2-1 below). Plug-in type receptacles have been provided to faciliatate replacing the ROM. If the malfunction disappears, leave the new ROM in. However, the ROM failure rate is extremely low, so if a new ROM does not fix the problem, go on to the following troubleshooting procedures.

Table 2-1

A 010101

ae [ort | rt | kt | rt |] rt | et

to}9101256

RT | et [| rt | RT

1 | Score | Car3478

ROM 0 ROM 1 ROM 2

If the ROM is alright, next check the ROM addresses at ROM inputs A°-A’. If these addresses are not alright, check the inputs to the multiplexers, the multiplexed outputs and any gating that may be between the multiplexer outputs and the ROM inputs.

The ROM address table is invaluable in troubleshooting this section. We will use a car image problem to demonstrate the use of the address table.

To find the correct address for the car image at the ROM inputs, look under the column labeled CAR A. Then clip the scope probe to the device that the ROM information is to be read into, which is shift register F6. The probe should be placed on the pin which is used to control when the data will be entered; in this case it is the shift load input (S/L) at pin 1. When the shift load pin goes low, the information will be loaded into the register.

Then take the second probe and check the ROM address inputs and compare these with the information at the multiplexer inputs. Finally, compare all of this information with the table.

For example, first check ROM address A” (pin

  • with the second probe, and you should see a high pulse occuring at the same time as the low shift
Page 43

Table 2-3 ROM Addresses

*32H_ 1 FIRST PART OF CAR

CARSCORETIMEIR.T.2R.T.SPEED CODEROMMULTIPLEX

A Cc D E F G ADD ADD

111000A10
1000119
1D31G2G256V256V_256V8A+C+D+EFG
1D21F2F128V128V128V7A+C+D+EFG
1D11E2E64V64V64V6A+C+D+EFG
1D¢1D2D32V32V0GO0 1 STOP5A+C+D+EF+G
32H*16V16V16V16V1R3 0 STOP4A+C+D+EF+G
1D48Vv8V512H=512H1R23A+CD+EF+G
104avav256H256H1R12A+CD+EF+G
1031C2c128H128H—-1R81A+C+D+EF+G
1021B2B64H64H1D¢0A+C+D+EF+G

0 SECOND PART OF CAR

load pulse. Note that this correctly corresponds to the ROM address table. Then look at A® (pin 8); again there should be a high pulse occuring simultaneously with the low shift load pulse. Now go to A®, and you should see signal 1D3 pulsing high and low as the steering wheel is rotated.

Continue to check all the address inputs in the same fashion. If you find some information that does not correctly correspond, start checking back through the multiplexers and gates, if any. If all the information checks out, examine the component that information is being loaded into (shift register F6 in this case).

The multiplexers are most easily checked using a logic comparator (see subparagraph 2.1.1). The comparator will yield fast and accurate results. If you do not have a comparator, use the following procedure: first tie both multiplexer select lines low and look at the information from pins 7 and 9 (multiplexed outputs) which must match the inputs at pins 6 and 10 (multiplexer inputs). If alright, tie S, high and $2 low, and pins 7 and 9 should match 5 and 11. If alright here, tie S, low and S; high, and 7 and 9 should equal 4 and 12. To check the last set, tie both select lines high and pins 7 and 9 should match 3 and

  • The enables 0-2 enable the appropriate ROM, depending on the function. Signal ABCD is true for score and car display. To troubleshoot the multiplexers, first check the multiplexer inputs. If any of these do not check out, go to the section that produces the malfunctioning signal and locate the malfunction there. However, if all the multiplexer inputs are alright, check the data select lines by going to gates H3 and L5. Verify the presence of the correct Ld1B, VLd1, 512H and SCORE DISP inputs. If all of the data select inputs are also alright, you must check the multiplexers themselves.

2.19 WINDOW CONCEPT After the video signals are generated by the computer, they must be displayed in the desired part of the CRT. This is done by directing the signals to appear only within a certain area or “window.” The key idea behind the window concept is that of limits or boundaries.

Your video probe is a test instrument that can be used to display the windows directly on the CRT. To see a graphic display of windows, attach one probe clip to the negative (—) side of the video coupling capacitor (C44) and run the other end across the sync counter outputs.

You probably noticed, as you ran the probe across the vertical sync outputs, that the resulting windows were horizontal in appearance. The most confusing part of the window concept is the fact that it takes vertical signals to define a horizontal window and vice versa.

Examine Figure 2-25a and notice the vertical signal 256V that defines a horizontal line approximately half way down the CRT. Since the raster is composed of 521 half lines (or 260.5 whole lines), the signal 256V “tells” the electron beam to modulate its scan

Page 44

SCORE OVS

TSA

ipa

ia

iow

ENAQE B —~

ENAGLE &

MOP e ENABLE tscL2foz

ni 12 Joo ENABLE 2

TSA Ts8 ——_

ENARLE 2

Figure 2-24 Memory Circuit

Page 45

sev 2m 128V WIDE ev -

HORIZONTAL WINDOW

Figure 2-25a Horizontal Window

Figure 2-25b Complete Window

at the 256th half-line down from the top of the screen and the lower half of the screen is white. This is why it takes a vertical signal to define a horizontal line a certain vertical distance down the CRT.

If we create a similar line, except 128 half-lines down the CRT, the result will be a band 128 half-lines wide bounded at the top by 128V and at the bottom by 256V. This band is known as a horizontal window.

A complete window is created by generating a similar vertical window and gating the two windows together, so that we have an area with all four sides defined.

The video signals are gated with the window so that they can only appear when the window occurs. The result is that the video can then only appear within the window.

2.20 INTRODUCTION TO MOTION The illusion of car motion is achieved by rapidly shifting the car image in the same way the illusion of motion is created on the motion picture screen by the film in the projector. The eye perceives this image shift as continuous motion because of a phenomenon known as retinal afterimage. The last seen image is ‘‘remembered” for a short time, and as the position of the image is shifted a number of times in rapid succession, the eye “overlaps” the images and perceives the shifting Process as continuous motion. Since the TV monitor has a frame rate of 30, it is possible to shift the car image so rapidly that the eye is completely fooled. The speed or velocity of the car image is determined by the shift rate/frame rate ratio. If the image is shifted once every frame it will appear to move much faster than if it were shifted only once every three frames. The direction of the image is controlled by varying the rate at which the car image windows are shifted with respect to each other.

Notice the vertical motion window in Figure 2-26a. As this window moves up and down, the image contained within it also moves up and down. Figure 2-26b shows the horizontal motion window that controls how the image is shifted from left to right. When the two windows are combined, the image can be vectored at any angle by individually varying the rate each window is shifted.

The speed of the image is controlled by shifting the window with respect to sync. If the window frequency is the same as sync, it will be displayed in exactly the same place during each TV frame and it will appear stationary. However, if the window is generated a little slower or faster than sync, it will be shifted a certain amount each frame and will appear to move.

This is done by entering different binary codes at the parallel inputs to the 9316 counters of the motion circuits. The stop code is the binary number that times the window with sync and therefore stops motion. Other codes cause a change in this relationship, and the window is shifted with respect to sync.

Figure 2-26a

Figure 2-26b ae

Page 46

Figure 2-26c

2.21 HORIZONTAL COUNT H COUNT is used to clock counter J2 (vertical positioning for the car image) twice per line.

Capacitor C9 and resistors R1 and R2 create a very short reset pulse for both L1 flip-flops, and this produces a high at both Q outputs. On the first 1H pulse, the Q output at L1 pin 2 goes low, while L1 pin 3 goes high; the Q at L1 pin 6 remains unchanged. On the second 1H pulse, L1 pin 2 goes high and L1 pin 6 goes low. On the 1H pulse, both L1 pin 2 and L1 pin 6 go low and stay low until both flip-flops are again reset by the capacitor and resistors. H COUNT TEST POINTS

TP 79: LOGIC PROBE: High and pulsing. OSCILLOSCOPE: See Figure 2-27. TP 80: LOGIC PROBE: Low and pulsing. OSCILLOSCOPE: See Figure 2-27.

2.22 VERTICAL CAR MOTION When VLd1 is high, the ROM data is latched into H7 and appears at the outputs until VIdT drops low again. This information is loaded into the parallel inputs of J7 when the line from L5 pin 3 goes low.

The counters start counting from the last number loaded in by L5 pin 3. They count up to 4096 , at which time a new number is loaded in.

The stop code for vertical motion is 3575 (1-1- 1-0/1-1-1-1/1-0-1-1), When this number is entered into the counters, car motion ceases (4096 minus 3575 equals 521, which is the sync frequency).

However, as the least significant digits of the stop code are changed, the 9316s begin their count from a different number and the resulting car window frequency is changed. For example, if the number 0-1-1-0 is loaded into J7, the window will move down at the slowest velocity (4096 minus 3574 equals 522 which is slightly faster than sync).

ttl 2.2 VOLTS ~-— +5 VOLTS OVOLTS +4 VOLTS OVOLTS

+5 VOLTS OVOLTS

Figure 2-27 Horizontal Count Circuit and Waveforms

Page 47

5 [3 |@ 3/3 ja is Pah 4 fot a Tiel oe waht eanfe,, ote Zs [R]W He Count >——4 4 RESET ee 8 38 po wom apoeess

Figure 2-28 Vertical Car Motion

Notice the RESET 1 line which resets the car image at the start of the game or after the car has been driven off the track.

VERTICAL CAR MOTION TEST POINTS

TP 81: Hold pin 1 of H7 low. Then using the oscilloscope or the logic probe, check to see if the input signals at pins 3, 4, 6 and 7 are reflected at output pins 15, 13, 12 and 10.

NOTE: CRT images break up when you hold VLd1 low.

To check counters, first look at pins 9 with the video probe. You should see a thin black line that moves with the car and is parallel to the bottom edge of the CRT. TP 82:

Then hold pins 9 low successively and check to see if the input signals of each counter (pins 3, 4, 5 and 6) are reflected at the outputs (pins 13, 12, 11 and 8).

At this test point, you will see the vertical car motion window appearing as a white horizontal band. TP 83: VIDEO PROBE:

2.23 HORIZONTAL CAR MOTION The only real differences between the horizontal and vertical motion circuits are that the horizontal counters are clocked by CLOCK rather than H COUNT, and that different numbers are loaded into the counters. VLd1 is normally low and goes high once per field. During the time VLd1 is low, the stop code 0-0-0-1 is loaded into E7. When Vid1 goes high, the ROM data is entered into E7 causing the horizontal motion window to shift.

Bom DATA 10, ae

Figure 2-29 Horizontal Car Motion

HORIZONTAL MOTION TEST POINTS

TP 84: Hold VLd1 low. This should generate the stop Code 0-0-0-1 at pins 3, 4, 5 and 6 of E7. Then hold pins 9 of E7 and D7 low and the stop code should be reflected at output pins 14, 13, 12 and 11 of E7 and D7.

TP 85: VIDEO PROBE: Thin black vertical line that moves with the car image.

TP 86: VIDEO PROBE: The video probe will reveal the horizontal car motion window appearing as a black band moving with the car image.

Page 48

can 4 1060

ExR 1 VIDEO.

Figure 2-30 Car Display

2.24 CAR DISPLAY The car display circuit uses both the outputs of the ROM and the outputs of the car motion circuits to generate the different aspects of the car image. The ROM supplies the necessary information for the car images; the car motion circuits move the car windows, and hence where the car image can appear. The display circuit displays all this information on the CRT.

Since the data at the ROM outputs are in parallel form, a shift register is necessary to convert this parallel (simultaneously occurring) information to serial (sequentially occurring) information. This is necessary so the information bits can be loaded one after another to be displayed by the electron beam as it sweeps across the CRT. Two shift registers are needed because the car image is made up of 16 bits, and each shift register can only process 8 bits of information at a time.

The information is loaded at different times into the shift registers by H SYNC and Ld1B. When H SYNC and Ld1B both go low, one set of car information is loaded into H6 by HSYNC and the register latches up this information when H SYNC returns high. Ld1B is still low and another set of car information is loaded into F6 and latched up when Ld1B returns high.

As long as the clock inhibit (1) of a shift register is high, the information remains latched in the register. However, when input | goes low, the clock pulses at pin 2 read out the information serially. The clock inhibit goes low during the car window signal which comes from the Q output of A5. The car window is the intersection of the vertical and horizontal car motion windows.

Thus, when the inhibit inputs of the registers go low, F6 reads out its latched-up information out pin 7 (the serial output) while H6 is simultaneously reading its information into F6. When all the information originally stored in F6 is read out F6 pin 7; Fé then reads out the information read into it by H6. All this information is gated with the car window at F7 to form CAR 1 VIDEO—the final car image signal.

CAR DISPLAY TEST POINTS

TP 87: VIDEO PROBE: Black square superimposed over car image.

TP 88: VIDEO PROBE: A number of horizontal white lines covering CRT from top to bottom. One or two of these lines intersect the car image and stop at the car.

2.25 RACE TRACK DISPLAY The information for the generation of the race track display is read out of the ROM, and this data is loaded into the parallel inputs of shift register E6 by RT CLOCK.

RT CLOCK is created at D3 by the gating of Ld1B with the modified 32H signal. The rising edge of 32H charges capacitor C38, which discharges through R54. It provides a very sharp high-going spike: there is also a low-going spike, but since it is below threshold voltage it cannot enable D3 and only the high-going spike is passed. This signal is gated with Ld1B, which allows only race track data to enter the shift register.

There are eight 4H pulses for every RT CLOCK pulse; the race track information is clock out E6 pin 9 serially by every 4H pulse.

Page 49

The resulting signal contains both the race track and the score information. Since the score window is generated at a different time than when the score information is read out of the ROM, the score window (SCORE DISP) must be delayed at C3 by 32H so that the resulting score window occurs simultaneously with the score information and in the correct part of the CRT.

SPECIAL DATA prevents the race track data from being displayed when special information such as the finish line, the checkpoints and the score need to be displayed. Otherwise, race track images would be “written over’ the special data. Whenever 2° and 2 go low and while 2' and Ld1B are high, the special data is clocked out 32H later.

The sizes of the pylons and the check points are determined by J1 and B3. This information is gated with SCORE DELAY at B3 and then with the race track and score information at C6 to form the complete race track signal (RT).

RACE TRACK DISPLAY TEST POINTS

TP 89: OSCILLOSCOPE: Frequency: 4.5 ys; duration: 0.1 4s. NOTE: No RT CLOCK pulse present when Ld1B goes low.

TP 90: VIDEO PROBE: Vertical 4H bars covering screen from left to right.

NOTE: Wider band in center is due to reset pulse. All race track windows visible. TP 91: VIDEO PROBE:

TP 92: VIDEO PROBE: White windows over score and timer displays.

TP93: VIDEO PROBE: Dark check point, finish line and non-delayed score and timer windows.

2.26 TIME AND SCORE STORAGE The primary functions of this circuit are to count the number of laps scored and the amount of elapsed time.

Laps are scored only by passing the race course checkpoints in proper order. If the check points are passed correctly, the lap score is increased by an increment of two. The information needed for generating the score images is contained within the ROM and read out by the following process.

The ROM data of the checkpoint location at the parallel inputs of £5 are loaded into that latch when RT CLOCK goes low and is latched when RT CLOCK goes back high.

The latched information enters the A and B inputs of the one-of-four decoders E3 and E4. The state of the E input controls the state of the selected output signal; the output signal is selected by the states of the A and B inputs. For example, if both A and B are low, output 0 will be selected; if E is low, the selected output 0 will also be low. If Ais high and B

TP

  • ee zo Se ed Se wv —feep\4 so PEE pslee) $f oz. —— 2 al ¥ SPECIAC DATA , |

Figure 2-31 Race Track Display

Page 50

is low, output 1 will be selected and if the E input is high, then output 1 will be high.

SPECIAL DATA (the signal from the race track display section containing the data for score display, oil slick, finish line and the checkpoints) is the E input to E4. Whenever SPECIAL DA A is low, the selected output of E4 will also be low.

For instance, when the checkpoint information is to be read out of the ROM, A will be low and B will be high. This selects output 2 which will be low because E (SPECIAL DATA) is also low. Output 2 then will contain all the checkpoint information, which is then sequentially selected by £3.

Output 0 of E4 is the finish line signal; however, it is 64 clock pulses wide—too wide for a functional finish line—so it is gated with RT CLOCK at B3. Since RT CLOCK is a spike of very short duration, the resulting finish line signal at B3 pin 13 will also be of very short duration and appear as a thin line. This thin finish line is then chopped into segments by gating it with 4V at A6 to give it a ‘dotted line” effect.

Laps are scored only by passing course checkpoints in the specified order: this is accomplished by selectively enabling latch F3. At the beginning of anew game, START goes high, clearing F3 so it can accept new information. Clearing F3 produces lows at pins 15, 13, 12 and 10 (1A, 1B, 1C and 1D); this causes lows to appear at pins 4, 6 and 7 and a high to appear at pin 3.

When the car passes through the first checkpoint, the car signal at pin 1 will go high, enabling the high at pin 3 to appear at pin 15, which in turn holds pin 4 high. When the car passes through the second checkpoint, the high at pin 4 will be enabled through to pin 13 and so on. This continues until the car has passed all the check points, at which time 1D will go high, incrementing counter F4 and simultaneously returning a low to pin

  • A low at pin 3 forces a low to appear at pin 15, which in turn causes pin 4 to be low. This then causes pin 13 to be low. This series continues until all the outputs are low and the latch is ready to record a new set of checkpoint and car image intersections.

The information at 1A, 1B, 1C and 1D must be converted to a binary code by gates A2, A3, D2 and E2 so that multiplexer D4 can correctly address the ROM score image information. The following truth table shows how this is accomplished.

D4 is a quad two-to-one multiplexer that selects either the score storage information or the game timer information. The signal is selected by 512H, and the outputs of the multiplexer (B, C, D and E) become inputs to the ROM multiplexers. Basically, these outputs tell the ROM what number to look up and read out for the score and timer number images stored within the ROM.

The ROM only stores 39 sets of number display information (the even numbers from 0-78) which limits the numbers which can be displayed for the score and game timer. The score will count up to 78 and the game timer counts down from 78.

C4 is the ones counter for the game timer and B4 is the tens counter. When START goes low, these counters begin counting down from the number loaded into the parallel inputs (78) and counts down by twos. When both counters reach zero, a low “borrow” (or END GAME) pulse is generated that resets the game to the attract mode. The length of the game can be changed by varying the 1 SEC pulses. Longer pulses are counted more slowly by the counters and thus the total game length is longer.

Table 2-4 Truth Table for Checkpoints

TP 94

NO CHECKPOINTS PASSED 1 CHECKPOINT PASSED 2 CHECKPOINTS PASSED 3 CHECKPOINTS PASSED 4 CHECKPOINTS PASSED =cooo a) TP 95 E5 pin 10 E5 pin 12 E5 pin 13 E5 pin 15 TP 96 TP 97 TP 99 TP 100 D4 pin 14 D4 pin 11

saaance aoa casco

Page 51

Figure 2-32 Time and Score Storage is] Fe Cprrr ele

RT Coote

Page 52

TIME AND SCORE STORAGE TEST POINTS

TP 94-100: See truth table (Table 2-4).

TP 101: When 512H is low, B, C, D-and E will read out the binary code for the score. When 512H is high, B, C, D, and E will read out the binary code for the timer.

TP 102: VIDEO PROBE: Two black non-delayed score and timer windows. TP 103: VIDEO PROBE: Four black check point windows.

TP 104: VIDEO PROBE: One black finish line window.

VIDEO SUMMER

A separate 5 volt power supply is used to power- M7, the video summer. This is to reduce the effect of noise on the video output.

+5X FROM 78L05

CAR 1 VIDEO FINISH LINE RT. + E—_{} VIDEO OUT 4.7K 10uf

Figure 2-33 Video Summing

Page 53

Number

A005886

005884

A005882

005904

A005885

005844

(none)

SCHEMATICS, DRAWINGS AND PARTS LISTS

Title

Parts List and Drawing Top Assembly

Parts List and Drawing Control Panel Assembly

Parts List and Drawing Double Foot Pedal Mounting Assembly

Schematic Harness Wiring

Parts List and Drawing Electronics Tray Assembly

Schematic, Parts List and Assembly Printed Circuit Board

Schematic Motorola XM501/701 Monitor

Page 54

SS¥ - TOP CABINET P/L acosese

PARTS LIS’ SPECIFICATION Page 1 of 1 Drawn Checked Mech, Eng. Proj. Eng | Elec, Eng Innovative leisure

Descri A iy [_B [Rev per Ecn 2782 |

po

ItemPart NumberQty.DESCRIPTION
1A005862-021Cabinet Assy with Graphics
2A0058841Control Panel Assy
3A0058821Metal Foot Pedal Assy
4A0054301Display Assy
5A0058831Sliding T.V. Shelf Assy
6A005912-021R.F. Shielding Enclosure Assy
7A004132-XxX1R.F. Shield P.C. Assy
8A005844dLP.C.B. Assy, Lemans
9A0058851Electronics Tray Assy
loA003637-111Coin Door Assy
ll0030532Retainer, Plex
1275-990900066Weldnuts #10-32
1382-80166Screws, Mach. THD., Allen Socket, Button Hd, #10-32 x/1"
140058921Lite Box Plexiglas with Graphics
15005378021Playfield Plexigal with Graphics
160058941Bezel, Cardboard with Graphics
170054191Speaker Grill, Cover
1873-770044Rivets, 3/16 x .68 Long
1975-5524B2Carriage Bolts, 4-20 x 14
2075-015S2Washers, Flat %
2175-0455Washers, Split Lock 4-20
2272-68081Screw, S.M. #8 x 4 Phil., Pan. Hd.
2372-55241Screw, Mach., Hex Hd., Stl. Cd. Plate 4-20 x 14 Lg.
2472-68244Screws, Sheet Metal #8 x 14, Phil, Pan Hd.
2572-68126Screw, Sheet Metal #8 x 3/4, Phil, Pan Hd.
2675-5124B6Carriage Bolts, #10-24 x 14
2775-01086Flat Washers, #10
2875-0406Lock Washers, #10-24
2975-91156Hex Nuts, #10-24
300027282Mntg. Brkt, Control Panel
3175-9354Wing Nuts #4-20
32A0058981Light Shield Assy
3372-66104Screw, S.M. #6 x 5/8, Phil. Pan Hd.
34TM-0771Techincal Manual
35A005901-XxX1Shipping Container
360052331Rear Door Seal
3782-1824lo | Screws, Wood, #8 x 14, Flat Hd. Phil.
38A0059061Rear Door Assy
3978-6601216A/R| Aluminum Foil (appx 2 ft)
0059081Extended Play Score Card
Page 55

ASS¥ d@L ‘LINIGWI

Page 56

Zw 13s 33 |v 1 ° e | sage Dee = D] SES COW = a a v ES a) SS Welt: ASSY dOL ‘LINIBYD won| moRHeDY r

  • om ~_n L wae WV [O_o Pa a ae

Wr 1074 a

arm Toaune? a Fe)

Er 0.4

WT man.

SuDSHs asuaERLLO STW SELON

Page 57

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 58

ASSY - CONTROL PANEL P/Lacoses4

PARTS LIST SPECIFICATION Page | of 1 Drawn Mech. Eng.

Elec. Eng

ee

DESCRIPTION Part Number. Qty.

10058501Control Panel with Graphics
2A000608- 011H-shift Assy
3A000598-031Steering Wheel Assy
40052551Shift Bezel
572-111210 | Mach. Screws, #10-24 x 3/4 Lg., Pan Hd Phil
6004304-071Switch Assy, One Player Start
70058891Shift, Spacer Block
80059074Control Panel Support
9A005896aHarness, Control Panel
100005671Bow, Washer
1185-22F4064 Ref Screws, Mach. F Type, #4-40 x 3/8 Lg.
120031781 Reff Lock Ring
1375-5524B2Carriage, Bolts, 4-20 x 14 Lg.
1475-O15S2Washers, Flat
1575-0452Washers, Split-Lock 4
1675-915S2Hex Nuts, 4-20
Page 59

no aR

SECTION

AA

Page 60

LEMANS

A.@ ASSY FOOT PEDAL MOUNTING

PARTS LIST SPECTFEECATION

Drawn ~ ATARI” Cheeked | Mech, Ene. Innovative Proj. lng. | Elec. Eng REV, leisure | B

Rev. | Deseription| hate JApory pRev.Description
temPart) NumberQty.DESCRIPTION
1A0047981Double Metal Foot Pedal Assy
20048011Mntg. Board, Foot Pedal
375-018S4Flat Washer, #8
475-0484Lock Washers, #8
575-918S5 Hex Nuts, #8-32
60021912Switch Brkt.
765-071C2Switch, Cherry
872-141284Mach Scr, #4-40 x 3/4'Lg Pan Hd Phil
975-0444Lock Washer #4
1075-914S4Hex Nut, #4-40
ll72-68124Screws, S.T. #8-3/4 Phil Pan Hd
1272-66121Screw, S.T. #6 x 3/4 Phil Pan Hd
13A0059001Foot Pedal Harness Assy
Page 61

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

7 om sit TRANS: i f= oie ane 201851 1, OR OR) Lov SHORTING T aldce Skown w co lox 31S oe NTERLOUE SwreHes

CON COUNTER BV

SW COM wien

EXTENDED PLAY TWISTED PAIR,

SPEAKER

-[afelolololefo]olw]o Bun Z| Fa

COIN,

COUNTER,

enre | |

Com COUNTER,

BRAKE © \ ESIN TOME: Se ! SSN Switgnes

\

ANT Peozive o3isin

¥ g my IPDHSETSOLE

Fi EXTENDED PLAY 2| ‘|

ANTENNA, Bevor|S, NO xe] NO NC

PLAYER START LP Lo twisted PAWS

coy | Y/8K Vv ron | ° | Sl ow

COIN SW ZNO VIDEO. COIN Sw 2 NG STEERING 1A PLAYER START NO STEERING 1B t =.

yt} ES T39/ BK i I 130) i ifs) ' 7!

>

°

(iol Be) ed ob ode ra

{| BU ~ x

W/GN =

GN r wIVads,

[Los ra

Iz [ele cco

BRAKE NO laeea5saH0S

=o ra a &

z Q

GAS © 4TH 5) oN °

woe w/v R i

2ND 3RD 1ST GAS NO Fy N BU ‘Sounsch sae ES DO NOT SCALE, R DRAWING

! GAS BRAKE 1

oN pe me |£ MANS BNW, HARNESS SCHEMATIC

BK GND Se 10. GND BU NOTES : UNLESS OTHERWISE SPECIFIED é |

> |e [2 [9 [x KrEmeabrors °

Ss ¥JS[N \TARI Oo

Page 64

PARTS LIST SPECIFICATION Page lof 1

ATARICheckedMech, Eng.
InnovativeProj. Eng.Elec. Eng

leisure LE MANS , 7 | ASSEMBLY TITLE # ELECTRONICS TRAY ASSY P/Laoosess-o1

Part Number.DESCRIPTION

002621 1 Electronics Tray

2A005903-011 Main Harness
379-32011 Fuse Holder
446-2012021 Fuse, 2 AMP
5001551-011 |Transformer 001551
60006221 Transformer Cover
70008711 Label
841-20011 Filter, Power Line
968-0021 Interlock Switch, AC Power
10000268-621 Bracket, Switch Mounting
iLA005926-011 Mini Harness
12A004576-05L Power Cord, 8 Ft Assy
13A001921-01A/R |Shorting Block, 95V
14A001921-02A/R |Shorting Block, 110V
15A001921-03A/R |Shorting Block, 220V H
16A001921-04A/R |Shorting Block, 220V L
17*72-66083 Screw, SM Pan Hd Phil #6 x & Lg.
1872-66125"uo""#6 x 3/4 Lg.
1972-68127"a“#8 x 3/4 Lg.
2075-2820B1 Screw, Mach, Rd Hd, Brass #8-32 x 1% Lg.
2l75-918B1 Nut, Mach, Brass, #8-32
22*68-0012 Interlock Switch, AC Power
23*000268-012 Bracket, Switch Mounting

*Items 22 & 23 are to be Substituted if Items 9 & 10 are not available & add a Qty of 2 to Item 17

Page 65

:

a

  • Bottom View 10 FOOT FEAL, Bir _ + SON om xg mage OE om Seercn A

a OREZ BERD C39 8 rex 2.2 Hac

TESTS ne we CURRENT VERSION -O1

i 4.8 © eat TeRMinas POS eee _Tor wiev DO NOT SCALE Ore arm at i tw (S — DRAWING

NOTES

) SHOWN IS THE PREFERREO NTERLOCK Strela Mountine seacner SASF KATABLE SSREH TSE Wet Nr Sen Nee econ Tine BOL KCTS k SHOWN OND SKETCH A: * fe)

NOTES : UNLESS OTHERWISE SPECIFIED

Page 66

RESET wo _nresey

START aw

iggy} vev0s [2 (sec r= erPL ‘ 7 [3 Pwceo | +sx to woeo 2 aus | Goeror teat OU sz fF} nev <i Rice sv

Fnise UNE

Page 67

45K FEO TOLOn

Want = >+—_—_ TOP SYNE

CAR VIDED FINISH LINE, <2e Ff vices eur ame oat

P ’ GRAN SEQUENCE —

seREgCH ARE:

ee, set UE SEREETH From ansacae

EAR 1 VIDEO AD, os TOME Bynes. -

Wee te

MFCBSAO

  • mpCeOdO Pu *s, 1 PARENTHES 1S nv CURRENT VERSION -O1 nav 25h inte on
Page 68

ava fwingas

3 . oe at = : of alal ater dial FS Oh erm ildtel ated 3-4 z apo

pes

Gi] 28 (er = a1

sas ’

ae Waa 2 5 7 : + : a > TA, a ass oo eng 591 ONSET rate ee TTTERT bauuagau

As

E for :

sisaarrava wi Fe NId OvorDSW

ss

Page 69

om SPEED KILL HEE Javeio our et es] 1a

<2 a

1K “ Res Lt “SV Ree ae les rs T 7” esp

+} -2)< ie a + {oe a es7 Lt ust + 6a

SCHEMATIC. LE MANS

Page 70

to STEERING eck RESET 4

SCREECH FROM ANALOG

vat tae

2 sec t

TSB

—_! er “a

Page 71

Ag _TS8 ewnaLe 4

SCHEMATIC LE MANS

Page 72

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 73

ASSEMBLY TITLE P.C. BD. ASSY., LE MANS P/L = A005844-01

PARTS LIST SPECIFICATION REV. A ASSEMBLY TITLE P.C. 8D. ASSY., LE MANS P/L n005844-01 PARTS LT SPECIFICATION REV. A rt Number DESCRIPTION Leen Number 2 DESCRIPTION

57 | 31-MRSOI 58 | 31-IN9T4 59 | 31-INuOOT 60 | 38-MV5013 61 | 33-2N2644 62 | 34-2N3643 63 | 3S-MCRI06-1 65 | 37-7400 90 | 37-9316 TA tc. 9316 ¥2,L2,07,£7,J7,K7,U7 91 | 37-9321 2 "9321 £3,E4 92 | 37-9322 \ "9322 i 93 | 37-MFc6040 2 " MEC6OhO FBMB gh | 37-MFC3340 *2 MFC3340. H8,L8 95 | 37-bord 1 41] #10 96 | 37-4016 1 " 4Ol6 DIO 97 | 37-78L05 1 +5V REG. 78L05 98 | 37-7812 1 || +av Res. 7812 99 | 37-79L05 ' -5V REG. 79L05 190 | 37-7912 1 j[ -1av Rec. 7912

DIODE, POWER MR5O1 CRI,CR2 "NgTh CR7-11,14 " IN4OOT CR3-6 LED, RED MVS013 R12, 13 TRANSISTOR, 2N3644 Q2,4,5 2N3643 Qr,3 SCR,MCRIO6-1 97,8

Newt NMA 1.c. 7400 P1,A2,M2,D3,D5,F5,L5,J10 66 | 37-7402 7402 F1,A3,83,H3,M3,C6 67 | 37-7404 " DhOb E1,02,N2,B6,J6,L6 68 | 37-74s04 1 " 74SO4 AB 69 | 37-7406 7406 K10 7O | 37-7408 7408 £2,A6,F7 71 | 37-7410 7410 AL,J1,HS 72 | 37-7413 ThA JB

  • | 37-7427 7427 M7 7h | 37-7hb2 1 7442 My 75 | 37-7474 15 “ 7n7h B1,C1,01,H1,B2,C3,N3,A4,A5, 85,C5,A7,87,C7,k8 7486 02,59 "7493 F2,H2,J2,F4,KS 7407 Ki,L1,D6 n 7H1S3 HA, Jd Key Lh Th 6h 49, K9 "7416S £6,F6,H6 7492 Ba, Ch "74193 J3,K3,I5 84 | 37-555 "555 B8,L10 85 | 37-566 566 c8,08,£8

86 | 37-LM309 1 |{Requlator, LM 309 87 | 37-LM324 1 LM3 2h F9,FIO 8e | 37-L380 1 "LM380 AYO

ov wo 102 | 66-117P HT y DIP SWITCH 7xSPST NI 10h | 78-16006 2 || staan ¢ 70-220) 105 | 90-101 1 jf CRYSTAL a}

106 } 78-06001 1 HEATSINK 107 | 78-16005 1 || sitpa9 108 | 005927-01 1 |] HEATSINK, -12V REGULATOR 103 | 005837-01 1 |} Rom 1 NS 140 | 005838-01 1 ROM 2 NA 111 | 005839-01 1 ROM 3 NO 112 | 35-2N6068A i TRIAC, 2NGO68A 06

aN

76 | 37-7486 77 | 37-7493 78 | 37-7407 79 | 37-74153 80 37-741 64 81 37-74165 82 | 37-74192

  • | 37-74193 11h | 72-1608¢ 145 | 75-0165 116 | 75-056 117 | 75-916C SCREW, MACH, PAN HD PHIL #6-32x3 CRES

WASHER, FLAT #6 WASHER, INT. LOCK #6 NUT, HEX, #6-32 CRES

an NN A

119 | 72-1406C 120 | 75-014s 121 | 75-054 122 | 75-914 SCREW, MACH PAN HD. PHIL #4~40x3/8 CRES

WASHER, FLAT #4 WASHER, INT LOCK #4 NUT, HEX, #4-40 CRES

nana

NAN tN MAM NM

NOTE: If item 93 (MFC6040) item 94 (MFC3340) may be subs S not available, 89 | 37-9314 af] 9314 F3,13,E5,H7 wed
Page 74

: i i ii ale Ht

SuMPeR BD

-UMPER © ~ suMPEe &

JUMPER

NOTES : UNLESS OTHERWISE SPECIFIED

Page 75

vomPee F

auMPER F

NOTES {UNLESS OTHERWISE svEciFiED): 1, THE FOLLOWING JUMPERS MUST BE ADDED As PART OF THE Pc. soaeD ASSEMALY, USING LARGE PADS AS INDICATED: AL FROM DIN 2 OF M7 (7427) TO PIN B OF BI (7478), FROM Pind 4 OF M7 (7427) TO PIN B OF AG(T408). POM PIN BS OF M7(7427) TO PAD INDICATED AS SUMPER C. BETWEEN THE TWO PADS INDICATED AS JUMPER 0. JFROW PIN & OF M2 (7400) TO PAL INDICATED AS coMPER E. AN |B GA, JUMPER BETWEEN THE TWO PADS INDICATED AS JUMPER F. aAgone ZOINSTALL MFC CO40'S IN FOSITIONS FS AND MOG. THESE May BE. SURETITUTED BY MFC2340's AT POSITIONS HB AND LB.

  • USE THis ASSY. DIG. WITH P.C.BD COS845 , REVISION A -

CURRENT VERSION -Ol

™ ASSEMBLY, LE MANS RC. BOARD

Page 76

w199009 19U_2s RAE uric: Bh

uty 03 86 2 322 ora ot

eis YORE man)

Page 77

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 78

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 79

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 80

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 81

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 82

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 83

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 84

ATARI INC. 14600 WINCHESTER BLVD LOS GATOS, CA 95030 408/374-2440 e TELEX 357-488