CATHODE RAY TOMES

Final Lap TM-322 1st Printing

Final Lap (Rev E) (Namco, 1987) · Technical Manual · 64 pages · 73 sections · original scan

Page 1

TM-322 ist printing

ATARI

GAMES

Final Lap is engineered and designed by Namco Ltd. Manufactured by Atari Games. Trademark and © Namco 1987. © 1988 Atari Games Corporation. All rights reserved.

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

A

ATARI

GAMES

Final Lap™ Operators Manual

with Illustrated Parts Lists

ATrARh SAMES |

Final Lap is engineered and designed by Namco Ltd. Manufactured by Atari Games. Trademark and © Namco 1987.

Page 4

© 1988 by Atari Games Corporation. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations, Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A 7s

Produced by the Atari Games Technical Publications Department

Page 5

Notice Regarding Non-Atari: Parts

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game.
  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.

NOTE

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatevef measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.

  • The power cord is properly plugged into a grounded thrée wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground plane, be sure the game printed-circuit boards (PCBs) are properly installed on the EMI Ground Plane. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.

iii

Page 6

Table of Contents

Set-Up How to Use This Manual Inspecting the Game... Installing the Seat Platform. Installing the Attraction Sign . Connecting Cabinets... Choosing the Car Type. Control and Switch Locations.... Setting the Coin and Game Options Game Play... Self-Test RAM Test ROM Test, Gas Pedal Test... -2 Brake Pedal Test -2 Steering Wheel Test. -2 Sound Test. Coin Options.. Difficulty Level 3 Number of Laps Communication Circuit Test Linked Games Car Type. Motion Test. Convergence Test. Reset the High Score Table Maintenance Preventive Maintenance .. Preventive-Maintenance Intervals Opening the Control Panel Maintaining the Steering Wheel Lubricating the Gear Shift. Maintaining the Pedals ... Cleaning the Coin Mechanism Cleaning the Interior Components. Repairs ...... Replacing the Steering Wheel Replacing the Steering Wheel Spring ..... Replacing the Steering Wheel Potentiometer Replacing the Gear Shift. Replacing the Microswitch on the Gear Shift Replacing the Stops on the Foot Pedal Replacing the Pedal Potentiometers Removing the Video Display.. Replacing the Video Display .. Removing the Game PCBs Replacing Static-Sensitive Devices Removing the Speakers

Page 7

4 Illustrated Parts Lists Glossary Warranty

List of Illustrations

Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4

Figure 2-1

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-8 Figure 4-8

Table 1-1

Table 3-1 Installing the Seat Platform ..... Connected Cabinets and Their Link PCBs . Car-Type Connectors... Control and Switch Locations

Self-Test Screen ....

Opened Control Panel. Steering Wheel Assembly Pedal Assembly..... Video Display and PC Board Removal. Speaker Removal.......

Cabinet-Mounted Assemblies. Control Panel Assembly .. Steering Wheel Assembly Foot Pedal Assembly .... Switching/Linear (SL) Power Supply Assembly Coin Acceptors, Inc. Coin Door Assembly... Final Lap CPU PCB Assembly Final Lap Video PCB Assembh Final Lap EMI PCB Assembly Final Lap Link PCB Assembly

List of Tables

Game Specifications .,

Recommended Preventive-Maintenance Intervals...

Page 8

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should be only be plugged into a grounded three-wire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the contiol panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock, High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the Parts list for this game, Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation,
CAUTION Properly Attach All Comnectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connecior, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:
NOTE—A highlighted piece of information.
CAUTION—Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions. ‘WARNING—Players and/or technicians can be killed or injured if instractions are not followed.
Page 9

Chapter 1

Set-Up

How to Use This Manual

This manual is written for game operators and service personnel, and provides information for setting up, playing, testing, and maintaining your Final Lap™ game. The manual is divided into the following chapters:

  • Chapter 1 contains set-up and game play information.
  • Chapter 2 contains self-test procedures.
  • Chapter 3 contains preventive maintenance and repair procedures. © Chapter 4 contains illustrated part lists. 2, Wiring and schematic diagrams é AAP XO for the Final Lap game cir-

got <P cuitry are contained in the “ S*° Schematic Package Supple-

xf ment (SP-322) included

with your game. This chapter includes information required to set up and play your Final Lap game. Carefully read the information in this chapter before applying power.

Page 10

Set-Up

WARNING To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area.

This cabinet should be connected to a grounded threewire outlet only. If you have several cabinets, each one should be connected to its own separate grounded outlet. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electricai shock if the cabinet is not properly grounded.

Inspecting the Game

WARNING Do not plug in the game until you have completed the following inspection steps.

Please inspect your Final Lap game carefully to ensure that the game is complete and was delivered to you in good condition. Figure 4-1 shows the locations of the parts of the game. Table 1-1 lists space, power, and environmental requirements. Inspect the game cabinet and seat assembly as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Unlock and open the lower service door. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. (The connector bracket next to the EMI enclosure is for the car type selection. One of three connectors can be plugged into the connector bracket or none of them may be. For more information, see Choosing the Car Type in this chapter.) Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed edge connector can damage a printed-circuit board (PCB) and will void your warranty.

1-2 b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected. e. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), and speaker. Make sure that they are mounted securely and that the ground wires are connected.

Table 1-1 Game Specifications

Characteristic Specification

Power Consumption —_150 V-A, 110 W RMS Temperature +5° to +50° C (437° to +122° F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (U.S. games) Width 50 in. (127 cm.) Depth (with seats) 64 1/4 in. 163.2 cm.) Height 60 in, (152.4 cm.) Weight 625 Ibs. (284 kg.)

Installing the Seat Platform

The seat platform is shipped separately from the game cabinet. The seat platform must be connected to the game cabinet with two pipes and two side brackets. The parts required for this procedure are packaged with the seat and in the extra parts package. The speaker harnesses must also be connected. See Figure 1-1, Installing the Seat Platform, for an illustration. Installation is easier if you set up the seat platform to face the cabinet before you begin. The seat platform also should be at least three feet away from the game cabinet.

  • Remove the two seat platform panels below and behind the seats by taking out the eight Phillipshead screws that hold each panel on the seat platform.
Page 11

‘Speaker Connection Plate Cabinet Harness Assembly

Seat Platform Bracket Set-Up

2in. screw

Seat Speaker Harness Assy

Figure 1-1 Installing the Seat Platform

  • Remove the pipe bracket inside each panel by removing the two hex-head screws that mount the bracket to the platform base.
  • Remove the two pipes from the cabinet packaging and find the 3/8-inch diameter holes drilled near one end of each pipe.
  • Put the pipe bracket on the end of the pipe with the drilled holes. The bracket must be in front of the drilled holes and the flat side of the bracket must face the seat platform.
  • Now, put the pipe in the seat platform and slide it all the way through the platform into the hole in the front.
  • Fit the drilled holes in the pipe over the two-inch screw shaft in the base of the platform.
  • Reinstall the pipe bracket.
  • Repeat steps 4 to 7 for the pipe on the other side.
  • Replace both seat platform panels,
  • Now slide the seat platform forward, and insert both pipes into the holes on the base plate of the cabinet. Stop when the seat assembly is about 8-10 inches from the game cabinet.
  • In the bottom panel, plug left speaker harness into the left connecior, Do the same for the right side, 12, Slide the seat platform all the way up to the cabinet. Be careful not to pinch the extra speaker harness wires, 13.In the parts package included with the game are two L-brackets and eight socket-head screws. Seat Platform Panel
Page 12

Set-Up

Screw these brackets onto the sides of the seat platform and then onto the cabinet base (see Figure 1-1). The holes in the seat platform and the cabinet are already threaded.

Installing the Attraction Sign

The attraction sign mounts behind the top panel of the game. See Figure 4-1.

  • Rest the attraction sign on the top panel retainer, behind the panel. Center the attraction sign.
  • Screw in the three Phillips-head wood screws to hold it in place.

ou | OC

One Cabinet

Connecting Cabinets

You can connect up to 4 cabinets. Each cabinet is shipped with a 6-foot long connecting cable. If you are connecting 3 or 4 cabinet togethers, you need longer cables. These are available from Atari Games Customer Service. These cables are 10 feet long (part no. 150031-120) and 20 feet long (part no. 150031-240).

  • Turn off the game power to all the cabinets.
  • Find the Link PCB in the back of the game. Plug in the connecting cables as shown in Figure 1-2. Each cable must be connected from an input to an output.

our, out

Ww w

Two Cabinets

Three Cabinets

OUT OUT OUT IT

IN IN IN IN

Four Cabinets

Figure 1-2 Connected Cabinets and Their Link PCBs

1-4

Page 13

Lotus Car (Yellow) Set-Up

McLaren Car (Red and White)

Car-Type Connector Bracket

Figure 1-3 Car-Type Connectors

  • Switch the connecting switch located on the Link PCB to the down position on all the cabinets that are linked together.

Choosing the Car Type

Each player can have one of four car types. These are selected by plugging in different connectors (included with the game) into the car-type connector bracket. The car-type connector bracket is next to the PCB enclosure and shown in Figure 1-3. At the factory, one car-type connector is plugged into the car-type connector bracket and the other two connectors are attached to it by a tie wrap. These are the car types and their connectors:

  • March—blue car. Plug in the connector with wires at all 4 pins.
  • McLaren—red and white car. Plug in the connector with wires at pins 2 and 4.
  • Williams—white, blue, and yellow car. Use 1o connector,
  • Lotus—yellow car. Plug in the connector with wires at pins 1 and 3,

Control and Switch

Locations

Power On/Off Switch The power on/off switch is located at the bottom left of the cabinet. (See Figure 4-1.) Volume Control The volume controls are located on the self-test utility panel behind the upper coin door, (See Figure 1-4.) Each player has two volume controls which adjust the level of sound from the two speakers on the seat headrest.

Self-Test Switch Each game has two self-test switches located on the utility panel behind the upper coin door. (See Figure 1-4.) The self-test switches are slide switches. Each video display has its own self-test switch that selects the Self-Test Mode to check game operation. See Chapter 2 for a complete description of the self-test.

Auxiliary Credit Switches

Each game also has two auxiliary credit switches, next to the self-test switches on the utility panel. These are push button switches. Use either auxiliary credit switch to give a player coin credits.

Left Player Right Player i i i ! i ‘Speaker Volume ! Speaker Volume Lo oR /LtL oR

Coin Couriters for LefiPlayer Right Player Left & Right Players —_ Self-Test Self-Test Switch and ‘Switch and Aux. Credit Aux. Credit

Switch Switch

Figure 1-4 Control and Switch Locations

Page 14

Set-Up

Connection Switch

NOTE If you have one cabinet, be sure the Link PCB switch is in the up position. Otherwise the game will not function properly.

The connection switch is on the Link PCB (see Figure 1-2.), This switch should be in the down position with connecting cables plugged in, if you have two or more cabinets connected together. For more information, read Connecting Cabinets in this chapter. Coin Counter The two coin counters, one for each player, are located on the utility panel inside the upper coin door. The coin counter records the number of coins deposited.

Setting the Coin and Game Options

The Final Lap coin and game options are set in the Self-Test Mode. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Play

This section of the manual describes the theme of the Final Lap game and the game play features. Introduction Final Lap is the first linked game designed for the amusement industry. Originally created by Namco Limited of Japan, Final Lap is a realistic racing game in the tradition of Pole Position. Each Final Lap unit is actually two games in one, with two seats and two separate video displays linked together for interactive play. Realistic player controls consist of a steering wheel with return-to-center steering, a high/low shifter, and gas and brake pedals. As many as four Final Lap units can be linked together for unprecedented competition: Up to eight players can compete head-to-head. Play Mode Imagine yourself racing head-to-head against the player sitting next to you. You see his car approaching in the rear-view mirror, and suddenly, he passes you on the inside, narrowly missing a road sign. You weave between the other competitive cars in hot pursuit. You are on his tail through the

1-6 hairpin and pass him in the straightaway! The status screen tells you that you are now in first position. You pass the finish line before the time runs out and again get extended time, but the question still remains: can you complete the final lap? To start the game, player(s) deposit coin(s) in the slot corresponding to their seat (e.g., the right player uses the right coin slot and the left player the left slot). The green light flashes, the green flag is waved and the race is on!

  • To begin a head-to-head race, players must deposit coins within 16 seconds of each other.
  • One player can compete against the clock or multiple players race can simultaneously on the same course.
  • Each player has his own realistic first-person perspective of the track and sees his competitors’ cars on his screen. « New players can start a new game even if another race is in progress.
  • As an incentive for multiple-player games, all players can continue for an extended time, as long as at least one player completes the lap within the time allowed on the computer clock shown in the center of the video display.
  • Players who set the best lap time are rewarded with a bottle of champagne in the winner's circle.
  • If a player's time is fast enough, the player can enter his initials on the high score table.
Page 15

Chapter 2

Self-Test

The Final Lap™ game tests itself and provides visual and audible indications of the condition of the game circuitry and controls. Self-test information is displayed on the screen and through the sound system. No additional equipment is required. We suggest that you perform a self-test at least once a day and when you first set up the game, connect additional cabinets, collect coins, or when you suspect game failure. Use the self-test to check the game circuits, check the option settings, and change the option settings. The self-test

switches (one for each display) are located on the utility panel behind the upper coin door. The self-test switches are the slide switches on the bottom of the utility panel.

Page 16

Self-Test

When you turn off the self-test switch, the game returns to the attract mode. When you turn on the selftest switch, the self-test screen appears To move through the options and tests, press both the gas and the brake pedals and change the gear shift from low to high. (You will hear a roar through the speakers when you change the gear shift.) The next option setting now flashes. To move to the next option or test, do the same procedure. You can only move down the screen. When you reach the end of the list, you return to the Sound test. To change a flashing option setting, move the gear shift from low to high. Do not press the gas or brake pedal. Every time you move the gear shift, a new setting appears. Once you choose a new setting, you can return immediately to the attract mode, if you like.

RAM Test

This tests the game RAMs. If the game RAMs are working correctly, OK appears. If the screen shows anything besides OK, a qualified technician should check the game boards.

ROM Test

This tests the game ROMs. If the game ROMs are working correctly, OK appears. If the screen shows anything besides OK, a qualified technician should check the game boards.

Gas Pedal Test

GAS is the gas pedal test. Press the gas pedal, and the number to the right increases. Release the pedal, and the number decreases. If you are not pressing on the gas pedal, the number should be 00. If the number

RAM OK ROM OK GAS 00 BRAKE 00 STEERING 00 SOUND 00 2 COINS 1 CREDIT 2COINS 1 CREDIT SCI OK LINK ON 2 CARTYPE LOTUS MOTION OFF

COIN 4; COIN 2: BANK 2B ROUND 4

HISCORE INITIALIZED

Figure 2-1 Self-Test Screen.

2-2 does not appear this way, then do the following:

  • Check to make sure the gas pedal is returning to top of its mechanical range. If it does not, repair or replace the gas pedal.
  • Turn the self-test switch off and then on again.
  • The number should reset to zero.
  • If it does not, check the potentiometer on the gas pedal.

Brake Pedal Test

BRAKE is the brake pedal test. Press the brake pedal, and the number to the right increases. Release the pedal, and the number decreases. If you are not pressing on the brake pedal, the number should be 00. If the number does not appear this way, then do the following:

  • Check to make sure the brake pedal is returning to top of its mechanical range. If it does not, repair or replace the brake pedal.
  • Turn the self-test switch off and then on again. 3, The number should reset to zero. 4, If it does not, check the potentiometer on the brake pedal.

Steering Wheel Test

STEERING is the steering wheel test. When you turn the wheel to the left, the number increases. When you turn the wheel to the right, the number decreases. If you are not turning the steering wheel, the number should be 00 or FF. If the number does not appear this way, then do the following:

  • Check to make sure the steering wheel returns to the center. If it does not, repair the steering wheel.
  • Turn the self-test switch off and then on again.
  • The number should reset to zero.
  • If it does not, check the potentiometer on the steering wheel.

Sound Test

SOUND is the sound test. Cycle through the five sounds to test the audio circuitry. Coin Options The COIN 1 option sets the coin option for each player. The COIN 2 setting does not apply to this game.

Page 17

You can choose 1 to 8 coins and 1 to 8 credits. The coin amounts and the credit amounts change independently of each other. The recommended option setting is 2 coins for 1 credit.

NOTE All players must have identical Coin 1 settings.

Difficulty Level

RANK is the difficulty level of the game. When you change the rank, you shorten or lengthen the game time.

NOTE Ali players must have identical Rank settings.

The levels are:

  • A (easy)
  • B (medium)—recommended setting
  • C thard) © D Gifficult)

Number of Laps

ROUND is the number of laps each player is permitted to complete in each game. If one player completes a lap in less than the allotted time, then all players receive another lap.

NOTE All players must have identical Round settings.

These are the settings for the number of rounds:

  • 4 (recommended setting)

Communication Circuit Test

SCI ON, at the top right of the screen, indicates whether the Game PCB communications circuits are working correctly. SCI ON should be followed by four letters and numbers. If it is not, check the connecting cables to other games and the connectors. Self-Test

Linked Games

LINK counts the number of game PCBs connected together (not the number of cabinets). LINK should always read On. If it reads Off, the switch on the Link PCB is in the wrong position. Check Figure 1-2, Link PCBs on Connected Cabinets, for the correct position of your switch. If you have one cabinet, the number of linked games should be 2. If you have 3 cabinets connected, the link number should be 6. If you do not have the correct number of links, check the connections between your games.

Car Type

The car type is the type and color of car that each player has. Each type of car has a different color. For more information about choosing the car type, see Choosing the Car Type in Chapter 1.

Page 18

Self-Test

Motion Test

MOTION does not apply to Final Lap. It should always read Off

Test Pattern

When you turn off the self-test, you will briefly see a test pattern. Use this screen to check the convergence and the color balance of the video display. For more information, see your video display service manual.

Reset the High Score Table

To reset the high score table, turn the steering wheel until the number 1F appears and change the gear shift to high. The words HISCORE INITIALIZED appear at the bottom of the self-test screen. The high score table now shows the default names and times.

2-4

Page 19

Chapter 3

Maintenance

This chapter includes preventive maintenance and repair procedures for the Final Lap™ game components that have the most use. To assure maximum troublefree operation from this game, you should perform preventive maintenance described in this chapter. Removal, disassembly, re-assembly, and replacement procedures are provided for components that might need to be repaired. If a game part is mentioned, but not illustrated, refer to Chapter 4, Illustrated Parts Lists, for information.

NOTE A hole is provided inside the upper coin door to store the tamperproof key wrench when it is not in use.
Page 20

Maintenance

Preventive Maintenance

Preventive maintenance includes cleaning, lubricating, and tightening hardware. How often preventive maintenance is performed depends upon the game environment and frequency of play. However, you should regularly maintain the components listed in Table 3-1, Recommended Preventive-Maintenance Intervals.

WARNING To avoid possible electrical shock, turn off the game before performing any maintenance procedures.

Preventive-Maintenance Intervals

For the best performance from your Final Lap game, perform the maintenance in Table 3-1 at the intervals specified.

Opening the Control Panel

  • Remove the four tamperproof screws on the top of the control panel.
  • Open the control panel on its bottom hinges. See Figure 3-1. Table 3-1 Recommended Preventive Maintenance Intervals Steering Wheel Lubricate and tighten every six months. Gear Shift Lubricate every six months, Brake and Gas Pedals Lubricate and tighten every six months. Coin Mechanism Inspect whenever you collect coins. Clean every three months.

Maintaining the Steering

Wheel

You should regularly maintain the steering wheel every 6 months. This maintenance includes the following:

  • Tighten the four Phillips head screws on the two stop brackets.
  • Tighten the socket-screw on the end of the steering shaft.

Microswitch

Gear Shift

Steering Wheel Assy ‘Tamperproot Screw

Figure 3-1 Opened Control Panel

3-2

Page 21
  • Tighten the two screws on the spring catch.
  • Lubricate the spring with Nyogel, a heavy petroleum grease.
  • Lubricate the bronze bearing at the end of the steering wheel case. Tightening the Screws on the Stop Brackets
  • When the control panel is open, the two stop brackets face the seats. See Figure 3-2.
  • Make sure the four Phillips-head screws are tight. They should be torqued to 28 inch-pounds.
  • If a screw has fallen out, replace it immediately.

SocketHead Screw

‘Shaft Washer

Hex Nut

Right Stop Bracket i

Maintenance

Tightening the Socket-Head Screw on the End of the Steering Shaft

  • Open the control panel.
  • Use a 3/16-inch Allen head wrench to tighten the screw on the end of the steering shaft. See Figure 3-2. Make sure it is torqued to 95 inch-pounds. Tightening the Screws on the Spring Catch The stop catch is mounted directly on the steering shaft, over the spring. The screws secure the spring catch, which keeps the spring in tension. See Figure 3-2.
  • Open the control panel.

24 Tooth Spur Gear

36 Tooth Spur Gear

Potentiometer

U Steering Wheel

Steering Wheel Cap

Figure 3-2 Steering Wheel Assembly

3-3

Page 22

Maintenance

  • Turn the steering wheel so you can reach both the socket-head screws and the nuts on the spring catch.
  • Use a 5/64-inch Allen head wrench for socket head screw and an 11/32-inch hex driver for nuts, and torque the screws to 28 inch-pounds. Lubricating the Spring Use Nyogel grease to lubricate the spring. Lubricating the Bearing
  • Take off the gear on the steering wheel shaft by removing the socket-head screw on the end of the shaft. See Figure 3-2.
  • Pry off the retaining ring. Cover the ring with a cloth while you pry it, so it doesn’t fly off.
  • Take off the washer. 4, Put two drops of light oi] on the top surface and inner surface of the bronze bearing.
  • Reassemble the steering wheel shaft.

Lubricating the Gear Shift

  • Open the control panel.
  • Put grease on the shifter plate. See Figure 3-1.
  • Check the round rubber bumpers for wear. If a bumper is worn, turn it.

Maintaining the Pedals

  • Take the pedal assembly out of the game. See Figure 3-3. Use a 5/32-inch Allen head wrench to re-

Button Head Screw

Gas Pedal Spring

Spring Bar

Potentiometer

Countersunk Screw

Gas Pedal

Figure 3-3 Pedal Assembly

3-4

Page 23

Finai Lap

move the four screws on the cover plate. These hold the assembly onto the cabinet. Pull the assembly out towards the seat.

  • Make sure the screw on the gear on each pedal is tight. If it is not, tighten it. See Figure 3-3.
  • Put two drops of oil on the shaft of the shoulder screw. . Replace the pedal assembly. 3.

Cleaning the Coin

Mechanism

Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residve in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.

Cleaning the Interior Components

WARNING Turn off the game power, but do not unplug the power cord before cleaning inside the cabinet. The power cord pro vides a ground path for stray static voltages that can be present on the cleaning tools. Maintenance

Perform the following procedure to clean the components inside the cabinet.

  • Open the rear access panel and display service panel.
  • Discharge the high voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a, Attach one end of a large, well-insulated, 18gauge jumper wire to ground, b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. c. Wait two minutes and repeat part b.
CAUTION Be extremely careful when cleaning the electrical components inside the cabinet. Avoid touching the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush.
  • Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the electrical components thoroughly (power supplies, PCB assemblies, display, etc.).
Page 24

Maintenance

Repairs

Repairs include the removal, disassembly, re-assembly, and replacement of game components. The following procedures are provided for components that may require repairs. ;

Replacing Steering Wheel

If you want to replace the steering wheel, but not the inside controls, follow this procedure. You do not need to open the control panel.

  • Pry the center cover off of the steering wheel.
  • Use a 1/4-inch Allen wrench to remove the three screws in the center of the wheel.
  • Remove the steering wheel. 4, Install the new steering wheel. Replace the screws and the center cover.

Replacing the Steering Wheel Spring

If the steering wheel does not snap back to the center when you turn it, replace the steering wheel spring. See Figure 3-2.

  • Open the control panel.
  • Loosen the screw on the end of the steering shaft. Take off small gear at the end of the steering shaft.
  • Pry off the retaining ring. Be careful when you pry it off, since it will fly off the shaft. 4, Remove the large washer below the retaining ring.
  • Take off both stop brackets by removing the Phillips-head screws holding the brackets on the case.
  • Take off the catch on the spring. Use 9/64-inch Allen wrench on the socket-head screws and an 11/32-inch hex driver on the Nyloc nuts. Remove the screws, nuts, spacers, and catch.
  • Pull the shaft out towards the steering wheel.
  • Put on a new spring. The spring must be well lubricated with Nyogel grease.
  • Replace the washer and retaining ring.
  • Replace the catch. Make sure it holds the spring in tension. . Replace the gear and the socket-head screw on the end of the shaft. The steering shaft gear must mesh with the gear on the potentiometer shaft and must be the same height. If not, move the gear on the potentiometer shaft. an

3-6

  • If you move the gear on the potentiometer shaft: a. Make sure flat part of the potentiometer shaft lines up with the center terminal on the potentiometer. b. Now put on the gear on the potentiometer. Make sure it completely meshes with the gear on the steering shaft and is the same height as the other gear. c. Check to be sure the potentiometer gear set screw is on flat part of potentiometer shaft and lines up with the center terminal on the potentiometer. Tighten the set screw.
  • When the gears mesh and are the same height, tighten the set screw on the gear on the potentiometer shaft.
  • Reassemble the steering shaft.

Replace the Steering Wheel

Potentiometer

If the steering wheel is working correctly, but the player’s car on the video display is not responding, you may need to replace the potentiometer. First check to see if the steering wheel fails the self-test. If it does, first check the mechanical parts of the steering wheel. If these are working properly, you may need to replace the potentiometer.

  • Open the control panel. See Figure 3-2.
  • Take off large gear on the potentiometer shaft. Use a 5/64-inch Allen head wrench to loosen the gear set screw.
  • Use a 1/2-inch hex driver to remove the lock nut and washer that hold the potentiometer on the case.
  • Push the potentiometer out towards steering wheel. Remove the wiring harness.
  • Replace the potentiometer. Put the key into the hole in the case.
  • Make sure flat part of the potentiometer shaft lines up with the center terminal on the potentiometer.
  • Tighten the potentiometer lock nut to 30 inchpounds.
  • Now put on the gear on the potentiometer. Make sure it completely meshes with the gear on the steering shaft and is the same height as the other gear.
  • Check to be sure the potentiometer gear set screw
Page 25

is on flat part of potentiometer shaft and lines up with the center terminal on the potentiometer. Tighten the set screw.

  • Install the wiring harness. The red wire is on the left, the brown wire is in the middle, and the black wire is on the right.

Replacing the Gear Shift

  • Open the control panel.
  • Disconnect the wiring harness from the gear shift.
  • With a 3/8-inch nut driver, remove the four nuts holding the gear shift on the panel. 4, Remove the gear shift through the front of the control panel.
  • Replace the gear shift. Assemble in reverse order.

Replacing the Microswitch

on the Gear Shift

  • Open the control panel.
  • Disconnect the wires to the switch on the gear shift. See Figure 3-1.
  • Remove the screws that hold the switch on the gear shift. 4, Remove the switch.
  • Replace in reverse order. Maintenance

Replacing the Stops on the

Foot Pedal

If one of the pedals sounds as if it is hitting metal when it is pressed or released, replace the rubber stops on the pedal.

  • Take the pedal assembly out of the game. Use a 5/32-inch Allen head wrench to remove the four screws on the cover plate. These hold the assembly onto the cabinet. Pull the assembly out towards the seat.
  • Remove the wiring harness from the gas and brake potentiometers.
  • Remove foot pedal plate by loosening the two countersunk socket-head screws that hold the pedal plate on the pedal arm. Use a 5/32-inch Allen head wrench. See Figure 3-3. 4, Remove the four screws around the pedal that hold it on the cover plate. Loosen the nuts with a 7/16inch wrench.
  • Loosen the spring bar that holds the spring in tension on the bottom rear of the pedal. Use a 3/16 Allen wrench on the socket-head screw and a 7/16 ‘wrench on the nut. Remove the screw.
  • Remove the two buttonhead screws on the front rubber stop that hold the stop on the metal plate. Use an 1/8-inch Allen wrench on the screws and a 3/8-inch wrench on the nuts. Remove the rubber stop and replace.
  • Replace the screws and nuts holding the rubber stop.
  • To replace the back horizontal stop, first remove the potentiometer and gear.
  • Loosen the lock nut on the potentiometer with a 1/2-inch flat wrench.
  • Loosen the set screw on the gear on the potentiometer.
  • Remove the gear from the potentiometer shaft.
  • Remove the potentiometer.
  • Remove the two button-head screws that hold the stop on the horizontal metal plate. Use an 1/8-inch Allen wrench on the screws and a 3/8-inch wrench on the nuts. Remove the rubber stop and replace.
  • Replace the screws and nuts holding the rubber stops.
  • Replace the potentiometer. Make sure the potentiometer key is in the hole in the case, so the flat side of the potentiometer shaft faces up.
  • Put on the lock nut, Tighten it part way.
  • Put the gear on the shaft. Make sure it completely
Page 26

Maintenance

meshes with and is the same height as the gear on the pedal.

  • Be sure the gear set screw is on the flat part of the potentiometer shaft and at twelve o'clock. Tighten the set screw.
  • Tighten the lock nut on the potentiometer.
  • Replace the screw in the spring bar. Tighten the screw.
  • Replace the pedal. Tighten the four screws that hold the pedal assembly onto the front plate. Replace the foot pedal plate and tighten the two screws that hold it in place.
  • Reconnect the wiring assembly. The wires to the brake (the left pedal) potentiometer are red on the top, orange in the middle and black on the bottom. The wires to the gas (the right pedal) potentiometer are red on the top, yellow in the middle, and black on the bottom.
  • Install the pedal assembly in the game.

Replacing the Pedal

Potentiometers

If the gas or brake pedal fails the self-test, you may need to replace the potentiometer. However, first make sure that the mechanical parts of the pedal are functioning properly. 1, Take the pedal assembly out of the game. Use a 5/32-inch Allen head wrench to remove the four screws on the cover plate. Pull the assembly out towards the seat.

  • Remove the wiring harness from the gas and brake potentiometers.
  • Loosen the lock nut on the potentiometer with a 1/2-inch flat wrench.
  • Loosen the set screw on the gear on the potentiometer.
  • Take off the nut, washer, and gear and remove the potentiometer.
  • Put on the new potentiometer. Make sure you insert the potentiometer key into the hole in the pedal assembly case.
  • Put on the washer and lock nut. Tighten the lock nut part way.
  • Replace the gear on the shaft. Make sure it completely meshes with and is the same height as the pedal gear.
  • Be sure the gear set screw is on the flat part of the potentiometer shaft and at twelve o'clock. Tighten the set screw.
  • Tighten the lock nut on the potentiometer.

3-8

  • Reconnect the wiring assembly. The wires to the brake (the left pedal) potentiometer are red on the top, orange in the middle and black on the bottom. The wires to the gas (the right pedal) potentiometer are red on the top, yellow in the middle, and black on the bottom,
  • Replace the pedal assembly in the game.

Removing the Video Display

Perform the following procedure to remove the video display. (See Figure 3-4.)

  • Turn the game power off and wait two minutes. Unplug the power cord.
WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display.

2, Remove the curved middle service panel and then the top service panei.

  • Be sure that the game power is turned off before discharging the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a. Attach one end of a large, well-insulated, 18gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. c. Wait two minutes and repeat part b. 4, Disconnect the display harness connectors from the display.
  • Use a 3/8-inch nut driver to remove the four hex head screws holding the video display mounting
Page 27

Final Lap Maintenance

Video Di Video Display Mounting Davia Hex Head Screw Bracket

EMI PC Board EMI Enclosure

Figure 3-4 Video Display and PC Board Removal

Replacing the Video Display

Perform the following procedure to replace the video display in the cabinet. (See Figure 3-4.)

  • Carefully lift the video display onto the display shelf in the cabinet. brackets on the cabinet shelf.
  • Carefully lift the display out.
WARNING To avoid dropping the video display, use extreme care when removing the display from the cabinet. We recommend that no one weighing less than 150 pounds should attempt to remove the display. In addition, we recommend that you wear gloves to protect your hands from the sheet-metal edges.
  • Replace the video display as described in the following procedure.
NOTE Whenever the cathode-ray tube and yoke are replaced as a single unit, readjust the brightness, size, and centering as described in the display manual. Also check the purity and convergence according to the display manual instructions, but adjust both only if required.
Page 28

Maintenance

  • Position the display so that the four holes in the video display mounting brackets align with the four holes in the video display shelf.
  • Install the four hex head screws through the mounting brackets and into the video display shelf. 4, With the hex-head screws loosely installed, push the video display forward to meet the bezel.
  • Use a 3/8-inch nut driver to tighten the bolts. Be sure that the display is centered horizontally.
  • Connect the display harnesses to the display.

Removing the Game PCBs

Perform the following procedure to remove or replace the Final Lap Video, CPU or EMI PCBs.

  • Tur the game power off.
  • Open and remove the lower service door.
  • The vertical green PC board is the EMI board. It is connected to the CPU PCB and the video PCB inside the EMI enclosure. The EMI enclosure is the perforated metal box. 4, Remove the 6 screws that hold the EMI PC board on the enclosure.
  • Take off the edge connectors on the EMI PC board.
  • Carefully pull the EMI PC board out, along with the CPU and the video PCBs.
  • Replace the Game PCBs in the reverse order of removal.

Replacing Static-Sensitive

Devices

Be careful when you are working with static-sensitive devices on the game PCBs. These can be microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge that has built up in your body can cause a Static-sensitive device to fail. Leakage from an improperly grounded soldering iron can also cause a static-sensitive device to fail. Before you handle a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded. A bare wire wrapped around your wrist and attached to an earth ground is effective when working extensively with static-sensitive devices. When you solder a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. Before you replace a static-sensitive device, make sure it is actually defective. A static-sensitive device can appear defective due to leakage on a PCB. To make sure a device is defective, ground any static voltages as described in the paragraph above. Clean both sides of the PCB with flux remover or an eraser. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Then test the device. If you are replacing a static sensitive device, new static-sensitive devices may be packaged in conductive foam or may have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it to a PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.

Removing the Speakers

Perform the following procedure to remove the speakers. (See Figure 3-5.)

  • Turn the game power off.
  • Remove the red fiberglass seat back. Remove all the screws from the sides of the seat, plus those on and behind the metal plate on the back of the headrest. You will need a Phillips screwdriver, an Apex A-2 square drive wrench, and an 1/8-inch Allen head wrench.
CAUTION Do not touch the speaker cone when handling the speaker. The cone material is fragile and can be easily damaged.
  • Disconnect the wires to the speaker. 4, Loosen the four nuts that hold the speaker on the speaker bracket. Remove the speaker. vw . Replace the speaker in the reverse order of removal, Be sure that you hook up the wires correctly. The signal wire on the speaker should be attached to the speaker tab marked with color, a “+” sign, or a round dot. (The signal wire is shown on the game wiring diagram; refer to the Schematic Package included with the game.)
  • Replace the seat back.
Page 29

Back Headrest Plate

Left Speaker Cover

Figure 3-5 Speaker Removal

Page 30

Maintenance Final Lap

N O T E S

3-12

Page 31

Chapter 4

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware parts, such as screws, nuts, washers, and so on usually are not in the parts lists. The parts lists (except for the PCB parts lists) are arranged alphanumerically by Atari part number. All Aprefix numbers, which are assemblies, come first. Next are part numbers with six numbers followed by a hyphen (000598- through 201000-). Ending the list are pait numbers with a two-number designation followed by a hyphen (00- through 99-). The PCB parts lists are arranged in alphabetical order by component. Each component section is arranged alphanumerically by reference designator. When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Atari Games Customer Service phone numbers are listed on-the inside front cover of this manual.

Page 32

Mlustrated Parts Lists Final Lap

[ Not Shown | ‘A045902-01 Main Harness Assy

4045903-01 Display Harness Assy

A045904-01 AC. Power Harness Assy

A045909-04 Jumper Select t bse? haw ‘ ‘Assy fop Service Panel 045843-02 Right Front Decal A085918-01 045843-03 045821-01 Utility Pane! Assy Center Front Decal Top Front Panet \ 045833-0 045843-01 Seat Platform Panel Lett Front Decal

045849-01 Middle Service Panel 139017-204 Video Display 045939-01 / Seat Cover 178056-002 Retainer 41/2-Inch Foam

045841-02 Right Side Decal ; Bezel 045844401 ‘Seat Back Decal a 045837-01 panoip oY Video Display Headrest Decal ‘Cover

045948-01 Viny| Number Dew cals

045947-01 Attraction Panel Decal

155028-001 176037-4016

Link PCB ‘Tamper Proot Screw

150031-072 Connecting So 78-6H002 Cable 045813-01 Rubber Mat 178126-002 Lower Service ‘Tamper Proot Door Key Driver 038091-01 045841-01 Left Side Decal 471027-001 04589104 0 Foot Pedal Assy TS con Decr

‘A045905-01 Cabinet Speaker Hamess Assy ‘4045784-01 Control Panel Assy 900401 Connection Plate Black Foam Tape

Figure 4-1 Cabinet-Mounted Assemblies, Front View A045781-01 B

Page 33

Final Lap Illustrated Parts Lists

045838-01 Back Headrest Plate

045946-01 Attraction Panel 045877-01 Speaker Bracket A045 783-01 045878-01 Seat Assy Left Speaker 045857-01 Top Panel Retainer

045938-01

PCB Enclosure

99-090361 Video PCB

99-090360 CPU PCB

155027-001 EMI PCB

72-5516 Hex Head Screw

045854-01 Seat Platform Pipe Bracket Bracket 01 A045782-01 04590 Seat Platforn Ass A045920-01 Seat Speaker Y Peer Supe Harness Assy sy

045852-01 Link PCB Bracket

178093-001 Fan slace Guard o4s056-01 ‘A045908-01 . Coortariess Connector Bracket

Assy 78-3201 Adjustable Glide

Figure 4-1 Cabinet-Mounted Assemblies, Rear View A045781-01 B

Page 34

Ilustrated Parts Lists

Cabinet-Mounted Assemblies Parts List

Part No. Description A045783-01 Seat Assembly. Replaceable Parts: A045782-01 Seat Platform Assembly 045838-01 Back Headrest Plate 045839-01 Seat Back Plate 045844-01 Seat Back Decal 045845-01 Headrest Decal 045858-01 Seat 045868-01 Car-Type Connector Bracket 045869-01 Seat Back 045877-01 Speaker Bracket 045878-01 Left Speaker Cover 045878-02 Right Speaker Cover 045879-01 Speaker Grille 045906-01 Seat Harness Assembly for Speaker 045938-01 Seat Cover 045939-01 Seat Cover Retainer 148007-003 4 1/2-inch Round Unshielded Speaker 176013-212 #8 X 3/4-inch Tapping Screw 82-8008B Button Head ,10-32 Black Screw 82-8020B Button Head 10-32 Black Screw A045784-01 Control Panel Assembly—see Figure 4-2 A045891-01 Foot Pedal Assembly—see Figure 4-4 A045902-01 Main Harness Assembly A045903-01 Display Power Harness Assembly A045904-01 A.C. Power Harness Assembly A045905-01 Cabinet Speaker Harness Assembly A045908-01 On/Off Harness Assembly A045909-04 Jumper Select Assembly A045918-01 Utility Panel Assembly A045920-01 Switching/Linear Power Supply Assembly—see Figure 4-5 038091-01 Cash Box 045813-01 Lower Service Door 045816-01 Top Service Panel 045821-01 Top Front Panel 045833-01 Seat Platform Service Panel 045837-01 Video Display Cover 045841-01 Left Side Decal 045841-02 Right Side Decal 045843-01 Left Front Decal 045843-02 Right Front Decal 045843-03 Center Front Decal 045847-01 Cabinet Base Trim 045849-01 Middle Service Pariel 045852-01 Link PCB Bracket

Page 35

Cabinet-Mounted Assemblies iustrated Parts Lists

Parts List, Continued

Part No. Description 045853-01 Seat Platform Trim 045854-01 Pipe Bracket 045855-01 Seat Platform Bracket 045856-01 Pipe 045857-01 Top Front Panel Retainer 045867-01 Speaker Connection Plate 045937-01 Bezel 045946-01 Attraction Panel 045947-01 Attraction Panel Decal 045948-01 Vinyl Number Decals 139017-204 Wells-Gardner Monitor 150031-072 6-Foot Connecting Cable 150031-120 10-Foot Connecting Cable (Not Included in Game; Order Separately) 150031-240 20-Foot Connecting Cable (Not Included in Game; Order Separately) 155027-001 EMI PCB 155028-001 Link PCB 171027-001 Coin Door With Top Sectioned Harness 176037-4016 Tamper Proof Button Head Black Screw 176019-212 LPW Black Screw 178056-002 1/2-Inch Double-Sided Foam Tape 178093-001 Fan Blade Guard 178126-002 10-24 Tamper Proof Hex Key Driver 178129-001 Wire Routing Clip 72-5516 1/4 Hex Head Screw

75-010F #10 Washer 75-O15F 1/4-inch Black Washer 75-0158 1/4-inch Steel Washer 75-0458 1/4-inch Split Lock Washer 75-5524B 1/4 Black Carriage Bolt 78-3201 Adjustable Glide 78-6900401 Black Vinyl Foam Tape 78-6HO002 Black Corrugated Rubber Matting. 82-8520B 1/4-20 Black Button Head Screw 99-090360 CPU PCB 99-090361 Video PCB

These are the technical supplements to the Final Lap game: CO-296-01 TM-296 Supplement SP-322 Final Lap Schematic Package TM-296 ‘Wells-Gardner 19" Standard-Resolution Video Display Service Manual "TM-322 Final Lap Operator's Manual

Page 36

IWustrated Parts Lists Final Lap

Not Shown

045843-01 Left Control Panel Decal

045844-02 Right Control Panel Decal

045858-01 Plastic Formed Dashboard

171088-001 Gear Shift

177010-244

176025-3616 4 = Tamperproof Screw

045848-01 ‘A045870-01 Control Panel Steering Wheel Assy

7551128 Carriage Bolt 75-8108B Carriage Bolt 75-5508B 1/4-20 Carriage Bolt

Figure 4-2 Control Panel A045784-01 A

4-6

Page 37

Final Lap Illustrated Parts Lists

Control Panel Assembly Parts List

Part No. Description A045870-01 Steering Wheel Assembly—see Figure 4-3 171088-001 Gear Shift (includes the snap-action switch, part no. 99-215003) 045842-01 Left Control Panel Decal 045842-02 Right Control Panel Decal 045848-01 Control Panel 044751-51 Plastic Formed Dashboard 177010-240 Polymer #10-24 Locknut 177010-244 Polymer 1/4-20 Locknut 75-010S Flat #10 Washer 75-0158 Flat 1/4 Washer 75-5112B 10-24 Black Carriage Bolt 75-5542B 1/4-20 Carriage Bolt

82-8512B 1/4-20 Button Head Tamperproof Screw

Page 38

Illustrated Parts Lists Final Lap

Not Shown

A045907-01 Steering Wheel Harness Assembly

72-8510 Socket-Head Screw

178101-014 178012-001 24 Tooth Spur Gear Retaining Ring

178101-008 175002-001 36 Tooth Spur Gear Shait Washer

045873-01 Catch

045875-01 Left Stop Bracket ioniome Potentiometer

72-1820F 8-32 Screw

045874-01 }77010-231 ty ‘ "ex Nut Torsion Spring

178027-001 Nyogel Lubricant

045934-01 Right Stop Bracket 178181-7804 Steel Spacer 178099-004 Steering Wheel

72-8512 Socket Head Screw

178245-001 Steering Wheel Cap

Figure 4-3 Steering Wheel Assembly A045870-01 E

4-8

Page 39

Illustrated Parts Lists

Steering Wheel Assembly Parts List

Part No. Description A045907-01 Steering Wheel Harness Assembly 045873-01 Catch 045874-01 Torsion Spring 045875-01 Left Stop Bracket 045934-01 Right Stop Bracket 175002-001 -750-inch Diameter Shaft Washer 177010-238 8-32 Nyloc Hex Nut 178012-001 .750-Inch Diameter Retaining Ring 178027-001 Nyogel Lubricant 178099-004 Steering Wheel 178101-008 36 Tooth Spur Gear with Hub 178181-7804 .250-Inch Long Steel Spacer 178245-001 Steering Wheel Cap 178103-014 24 Tooth Spur Gear (Acceptable substitute is part no. 178101-007, gear with hub) 19-9026 5K Ohm Potentiometer 72-8822 8-32 Socket Head Screw 75-8510 1/4-20 Socket Head Screw 75-010S Flat #10 Washer

Page 40

Illustrated Parts Lists Final Lap

Not Shown

A045893-01 Pedal Harness Assy

045890-07 Brake Pedal Spring

82-8012 045896-01 Button Head Screw 728516 Rubber Bumper 174-20 Socket- Head Screw

045896-01 Rubber Bumper

045895-01 Modified Spur Gear

040249-01 Spur Gear

177010-241 Locknut

Figure 4-4 Foot Pedal Assembly A045891-01 A

4-10

Page 41

Illustrated Parts Lists

Foot Pedal Assembly Parts List

Part No. Description A045893-01 Pedal Harness Assembly 045889-01 Accelerator Pedal Spring 045890-01 Brake Pedal Spring 045896-01 Rubber Bumper 177010-241 10-32 Hex Polymer Locknut 177010-244 1/4-20 Hex Polymer Locknut 19-9026 5 K Ohm Potentiometer 72-8408 Socket Head 4-40 Screw 72-8604 Socket Head 6-32 Screw 75-010S #10 Flat Washer 82-8012 10-32 Button Head Screw 85-1514 1/4-20 Flat Countersunk Socket Head Screw

4-11

Page 42

Illustrated Parts Lists

A043367-08 12-Inch Black Jumper

4049967-09 ase 149008-001 i rs 2-Positon Terminal Block 12-Inch White Jumper Hitron 5V/12V Switching Assy Power Supply Assy

A042364-01 RFI Filter Assy

46-2013002 3A, 250 V, Slow-Blow Fuse

178225-2201 1-Position Fuse Block

043367-01 3-tnch Black Jumper Assy 142045-001 034544-01 NS | Isolation Transformer Fuse Block Cover

Figure 4-5 Switching/Linear Power Supply Assembly A045920-01 A

4-12

Page 43

Final Lap Illustrated Parts Lists

Switching/Linear Power Supply Assembly Parts List

Part No. Description

A042384-01 RFI Filter Assembly A043367-01 3-Inch Black Jumper Assembly A043367-08 12-Inch Black Jumper Assembly A043367-09 12-Inch White Jumper Assembly 034544-01 Fuse Block Cover 043396-01 Power Supply Base 142045-001 120 VAC Isolation Transformer 149008-001 Hitron 5V/12V Switching Power Supply Assembly—see below 179225-2201 1-Position Fuse Block 179231-002 2-Position Terminal Block 46-2013002 3 A, 250 V, Slow-Blow Fuse

Hitron 5V/12V Power Supply Sub-Assembly Parts List

Part No. Description

Capacitors 99-211036 Capacitor, Metal Film, 0.047 pf, 250V 99-211037 Capacitor, Metal Film, 0,22 pf, 100V 99-211038 Capacitor, Metal Film, 0.1 pf, 400V 99-211039 Capacitor, Metal Film, 0.022 pf, 100V 99-211040 Capacitor, Ceramic, 1800pf, 2 KV, Z5V 99-211041 Capacitor, Ceramic, 0.01uf, 1 KV, Z5U 99-211042 Capacitor, Ceramic, 0.001 pf, 2 KV 99-211043 Capacitor, Ceramic, 470 Pf, 1KV, Z5P 99-211046 Capacitor, Electrolytic, 100 pf, 200V 99-211047 Capacitor, Electrolytic, 1000 pf, 25V 99-211079 Capacitor, DE7100F22M 99-211080 Capacitor, 1000 pf, 35V 99-211081 Capacitor, 470 pf, 25V 99-211082 Capacitor, 220 pf, 16V Diodes 99-211005 Diode, Schottky, S10SC4M. 99-211007 Diode, Zener, 1N752A 99-211008 Diode, Rectifier, 1N4006 99-211009 Diode, Fast Recovery, RPG10B 99-211010 Diode, Fast Recovery, RPG10K 99-211011 Diode, Fast Recovery, RPG15B 99-211012 Diode, Switching, 1N4148 99-211076 Diode, 31DQ04 Inductors 99-211084 Inductor, 8 ph

4-13

Page 44

Ulustrated Parts Lists Final Lap

Hitron 5V/12V Power Supply Sub-Assembly Parts List, Continued

Part No. Description

99-211085 Inductor, 9.8 ph 99-211086 Inductor, 0.75 mh 99-211087 Inductor, 2.2 ph 99-211088 Inductor, 60 mh Resistors 99-211014 Potentiometer, Trimming, 3K Ohm 99-211016 Resistor, Wire Wound, 150 Ohm, +5%, 2W 99-211017 Resistor, Wire Wound, 33 Ohm, +5%, 2W 99-211018 Resistor, Wire Wound, 0.47 Ohm, +5%, 2W 99-211019 Resistor, Wire Wound, 120 Ohm, +5%, 2W 99-211020 Thermistor, 0.5 Ohm, +5%, 5W 99-211021 Resistor, 2.2K Ohm, #2%, 1/4W 99-211023 Resistor, Carbon Film, 270 Ohm, +5%, 1/2W 99-211024 Resistor, Carbon Film, 470 Ohm, +5%, 1/4W 99-211025 Resistor, Carbon Film, 47 Ohm, 5%, /4W 99-211026 Resistor, Carbon Film, 330 Ohm, +5%, 1/4W 99-211027 Resistor, Carbon Film, 5.6 Ohm, +5%, 1/4W 99-211028 Resistor, Carbon Film, 8.2 Ohm, +5%, 1/4W 99-211029 Resistor, Carbon Film, 10 Ohm, +5%, 1/4W 99-211030 Resistor, Carbon Film, 39 Ohm, +5%, /4W. 99-211031 Resistor, Carbon Film, 56 Ohm, +5%, 1/4W 99-211032 Resistor, Carbon Film, 1K Ohm, +5%, /4W 99-211033 Resistor, Metal Film, 2K Ohm, +2%, 1/4W 99-211035 Resistor, Carbon Film, 2K Ohm, +5%, 1/4W 99-211077 Resistor, 470 Ohm, 1/2W, +5% 99-211078 Resistor, 120K Ohm, 1W, 25% Transistors 99-211002 Transistor, NPN, 28C1413A 99-211003 Transistor, NPN, PE8050B Miscellaneous 99-211059 Heat Sink 99-211061 Heat Sink, 1.5mm 99-211089 Transformer, 4.75 mh 99-211083, Transformer, Power 99-211001 Regulator, UA431AWC 99-211013 Rectifier, Silicon-Controlled, $2800

4-14

Page 45

Final Lap Illustrated Parts Lists

N O T E S

Page 46

lustrated Parts Lists Final Lap

99-10140 Panel Assembly

99-10116 Lever 99-10152 SY Right Coin iniet 99-10147

171006-035 Coin Mechanism Ne

75-944 S Locknut ~ 99-10096 Fastener

99-10151 Left Coin Inlet

99-10105 72-9406S Bar Screw

SF

99-10104 Bar Retainer

99-10042 thru 99-10045 99-10154 Coin Switch Assembly Bracket Assembly

99-10150 10153 f NN va ‘ . : N ¢ < ° | it epiboes y, > Switch Cover Coin Chute ~

65-441C ty Coin Switch 7 is

99-10075 thru 99-10078 A Switch Wires .

99-1008 Retainer 75.14125 Screw

Figure 4-6 Coin Acceptors, Inc. Coin Door Assembly 1710270-001 A

4-16

Page 47

72-HA1404C Screw

99-10139 Coin Door

99-10148 Lock Assembly

SS

i) % %

72-3A1405B Screw

038091-01 Coin Box Illustrated Parts Lists

99-10160 Coin Inlet Housing

99-10161 Side Entry Button Assy

Spring

99-10141 Coin Return Cover

99-10117 Coin Retum Door

I<—— 99-10144 ‘Channel Ciip

99-15066 Screw

99-10149 Service Door

NOTE

The acceptabie substitute for this door (and the one used in games manufactured in ‘reland) is the Coin Controls Ltd. Coin Door Assembly, part number 171034-001. You can obtain a free Coin Controls Ltd. supplement (part. no. CO-305-01) that has illustrations and a parts list. Write to Atari Games Ireland Limited, Tipperary Town, Ireland. Telephone 062-52155. 99-10143 Frame

Figure 4.6 Coin Acceptors, Inc. Coin Door Assembly, Continued 1710270-001 A

Page 48

Illustrated Parts Lists

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x 3/8-Inch Truss-Head Screw 72-HA1404C #4-40 x 1/4-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x 3/4-Inch Pan-Head Screw 75-9948 #4-4) Locknut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. 25¢ 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch Wire Gacluded in coin switch assembly 99-10043) 99-10076 Switch Wire (included in coin switch assembly 99-10042) 99-10077 Switch Wire (included in coin switch assembly 99-10044) 99-10078 Switch Wire (included in coin switch assembly 99-10045) 99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener 99-10104 Bar Retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever

99-10117 Steel Coin Return Door 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover

99-10143 Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly 99-10160 1-Inch Wide Die-Cast Coin Inlet Housing 99-10161 25¢ Amber Side-Entry Coin Button Assembly

99-1506 Screw for Clamp

171006-035 Metal Coin Mechanism for U.S. 25¢

4-18

Page 49

Ilustrated Parts Lists

N O T E S

4-19

Page 50

Illustrated Parts Lists 2802320-E43

P2p3 1sisee rer 9 Los Tez BLO

R234 2SAl05-¥ TRS'6)7 280 125-¥

4-20 ? (26189P 32.00)

e-F

1a 8618961200 SF S| + Q CICIC zsavous-v«3 is

+e001le

ig iF o H

Seow_lz reas th oO8
Sdi id208
ene7ge ae»
ae|, easesee

co 3

=.ot
ates= *oo 80 ‘

4 ene mye

L a

3oi.otTF Fe
+ useaed“Pc20
pSiyomA
pacearr7.

n

ar

EE ae

“tz 2 soe |

ven GPL @ meEro”oORE

Likerne 8 wae prt ge | [

10 gy aigj H.

re

*

30 ‘

tase) Suse ge 2 tan

eran r

yas

ee a : is carn Bree 7

99-090360 Figure 4-7 Final Lap CPU PCB Assembly

Page 51

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 52

Illustrated Parts Lists Final Lap

Final Lap CPU PCB Assembly Parts List

Part No. Description

Integrated Circuits 136063-2101 IC, PR EPROM, Final Lap, MPO, 11D 136063-2102 IC, PR EPROM, Final Lap, MP1, 13D 136063-1103 IC, PR EPROM, Final Lap, SPO, 11K 136063-1104 IC, PR EPROM, Final Lap, SP1, 13K 136063-1105 IC, PR EPROM, Final Lap, CHRO, 11N 136063-1106 IC, PR EPROM, Final Lap, CHR1, 11P 136063-1107 IC, PR EPROM, Final Lap, CHR2, 11R 136063-1108 IC, PR EPROM, Final Lap, CHR3, 11S 136063-1109 IC, PR EPROM, Final Lap, CHR4, 9N 136063-1110 IC, PR EPROM, Final Lap, CHRS, 9P 136063-1111 IC, PR EPROM, Final Lap, CHR6, 9R 136063-1112 IC, PR EPROM, Final Lap, SNDO, 7J 136063-1113, IC, PR EPROM, Final Lap, SHAO, 7N 136063-1114 IC, PR EPROM, Final Lap, VOI], 3M 136063-1115 IC, PR EPROM, Final Lap, VOI2, 3L 136063-1116 IC, PR ROM, Final Lap, FL3, 5B 136063-1117 IC, PR PROM, Final Lap, 6R 136063-1118 IC, PR ROM, Final Lap, OBJOB, 5F 136063-1119 IC, PR ROM, Final Lap, OBJ1B, 4F 136063-1120 IC, PR ROM, Final Lap, OBJ2B, 5H 136063-1121 IC, PR ROM, Final Lap, OBJ3B, 4H 99-090110 Integrated Circuit, 741804 99-090111 Integrated Circuit, 74LS08 99-090115 Integrated Circuit, 741874 99-090120 Integrated Circuit, 741S157 99-090124 Integrated Circuit, 7418245 99-090136 Integrated Circuit, TMM2018D-45 (45ns) 99-090147 Integrated Circuit, YM2151 99-090155 Integrated Circuit, Custom 95 99-90158 Integrated Circuit, DAC, YM3012 99-090244 Integrated Circuit, 7418244 99-090248 Integrated Circuit, Op-Amp, TLO84CN 99-090288 Integrated Circuit, 74F04 99-090291 Integrated Circuit, 74HC175 99-090300 Integrated Circuit, Custom 116 99-090303 Integrated Circuit, Custom 121 99-090313 Integrated Circuit, 74F138 99-090314 Integrated Circuit, 74F244 99-090315 Integrated Circuit, 74F374 99-090318 Integrated Circuit, Custom 123

4-22

Page 53

Illustrated Parts Lists

Final Lap CPU PCB Assembly Parts List

Part No. Description 99-090320 Integrated Circuit, 78L06 99-090322 Integrated Circuit, TA7630 99-090323 Integrated Circuit, {B1760 99-090324 Integrated Circuit, MB3771 99-090362 Integrated Circuit, 74S15 99-090363 Integrated Circuit, 744C240 99-090364 Integrated Circuit, 74HC74 99-090365 Integrated Circuit, CPU, HD68000-12 99-090366 Integrated Circuit, CPU, MC68000G12 99-090367 Integrated Circuit, CPU, 68B09EP 99-090368 Integrated Circuit, CPU, HD68BO9E 99-090369 Integrated Circuit, RAM, MB8464A-15-SK 99-090370 Integrated Circuit, RAM, MPD4364CX-15 99-090371 Integrated Circuit, RAM, HM6225GP-120 99-090372 Integrated Circuit, RAM, M5M5256AP-12 99-090373 Integrated Circuit, RAM, MPD4325GC-120 99-090374 Integrated Circuit, RAM, SRM2025GLC12 99-090375 Integrated Circuit, RAM, MB84256-10 99-090376 Integrated Circuit, RAM, M5MS178-55 99-090377 Integrated Circuit, RAM, M5M5179-55. 99-090378 Integrated Circuit, RAM, MB8422-12 99-090379 Integrated Circuit, RAM, HM6525GBSP-12 99-090380 Integrated Circuit, PAL, 1618, SYS87B-1 99-090381 Integrated Circuit, PAL, 16L8, SYS87B-2 99-090382 Integrated Circuit, PAL, 12110-2, SYS87B-3 99-090383 Integrated Circuit, EEPROM, HNS58C6SP-25, 99-090384 Integrated Circuit, Custom 137 99-090385 Integrated Circuit, Custom 139 99-090386 Integrated Circuit, Custom 140 99-090387 Integrated Circuit, Custom 145 99-090388 Integrated Circuit, Custom 148 99-090389 Integrated Circuit, Custom 149 99-090390 Integrated Circuit, Custom 156 99-090391 Integrated Circuit, Custom 65 99-090392 Integrated Circuit, Op-Amp, LAG082S 99-090393 Integrated Circuit, Audio Amp, LA4700 99-090394 Integrated Circuit, DAC, LC7880 99-090395 Integrated Circuit, TA7376 99-090396 Integrated Circuit, Voltage regulator, 78L05 99-090398 Integrated Circuit, PC900 99-090399 Integrated Circuit, PC910 Diodes 99-090250 Diode, 181588 99-090326 Diode, 126.2 . Inductor 99-090274 Inductor, 100 pH, $P0406-101K

4-23

Page 54

Illustrated Parts Lists Final Lap

Final Lap CPU PCB Assembly Parts List

Part No. Description

Resistors 99-090183 Resistor, SIP, 1 K Ohm x 4, 1/8 W 99-090185 Resistor, SIP, 4.7 K Ohm x 8, 1/8 W 99-090188 Resistor, 680 Ohm, +5%, 1/4 W 99-090189 Resistor, 330 Ohm, +5%, 1/4 W 99-090192 Resistor, 560 Ohm, 45%, 1/4 W 99-090193 Resistor, 1 K Ohm, +5%, 1/4 W 99-090194 Resistor, 4.7 K Ohm, +5%, 1/4 W 99-090196 Resistor, 10 K Ohm, +5%, 1/4 W 99-090199 Resistor, 1 M Ohm, +5%, 1/4 W 99-090252 Resistor, SIP, 2.2 K Ohm x 4, 1/8 W 99-090255 Resistor, 100 Ohm, +5%, 1/4 W 99-090257 Resistor, 2.2 K Ohm, +5%, 1/4 W 99-090305 Resistor, SIP, 100 Ohm, 1/8 W 99-090306 Resistor, SIP, 2.7 K Ohm, 1/8 W 99-090307 Resistor, SIP, 470 Ohm, 1/8 W 99-090309 Resistor, SIP, 1 K Ohm. 99-090331 Resistor, 100 K Ohm, 1/4 W, +5% 99-090332 Resistor, SIP, 1 K Ohm, 1/8 W 99-090333, Resistor, SIP, 1.2 K, 1/8 W 99-090336 Resistor, SIP, 10 K Ohm, 1/8 W 99-090351 Potentiometer, 10 K Ohm 99-090400 Resistor, SIP, 4.7 K Ohm, 1/8 W 99-090401 Resistor, SIP, 2.2 K Ohm, 1/8 W 99-090402 Resistor, SIP, 4.7 K Ohm, 1/8 W 99-090403 Resistor, 2.2 Ohm, 1/4 W 99-090404 Resistor, 10 Ohm, 1/4 W 99-090405 Resistor, 22 Ohm, 1/4 W 99-090406 Resistor, 47 Ohm, 1/4 W 99-090407 Resistor, 75 Ohm, 1/4 W 99-090408 Resistor, 220 Ohm, 1/4 W 99-090409 Resistor, 4.7 M Ohm, 1/4 W 99-090410 Resistor, 270 Ohm, 1/8 W Transistors 99-090310 ‘Transistor, 2SA1015-Y 99-090311. Transistor, 2SC2320-E 99-090328 ‘Transistor, 2SC2236-Y 99-090397 Transistor, 2SC1815-Y Capacitors 99-090171 Capacitor, Ceramic, 22 pf, 25V 99-090172 Capacitor, Ceramic, 100 pf, 25V 99-090174 Capacitor, Ceramic, 0.01 pf, 25V 99-090175 Capacitor, Ceramic, 0.1 pf, 25V 99-090180 Capacitor, Ceramic, .033 yf, 50V, £10% 99-090266 Capacitor, Ceramic, .0047 pf, 50V, +10% 99-090267 Capacitor, Ceramic, .01 af, 50V, +10% 99-090269 Capacitor, Electrolytic, 10 pf, 16V

4-24

Page 55

Illustrated Parts Lists

Final Lap CPU PCB Assembly Parts List

Part No. Description 99-090270 Capacitor, Electrolytic, 47 yf, 16V 99-090273 Capacitor, Electrolytic, 100 pf, 16V 99-090347 Capacitor, Electrolytic, 22 pf, 16V 99-090350 Capacitor, Electrolytic, .47 pf, 50V 99-090411 Capacitor, Ceramic, 1000 pf, 25V 99-090412 Capacitor, Ceramic, 3 pf, 25V 99-090413 Capacitor 99-090414 Capacitor, Ceramic, 0.001 pf, 50V 99-090415 Capacitor, Ceramic, 0.0022 pf, SOV 99-090416 Capacitor, Ceramic, 0.022 pf, 50V 99-090417 Capacitor, Ceramic, 0.12 pf, 50V 99-090418 Capacitor, Electrolytic, 1 pf, SOV 99-090419 Capacitor, Electrolytic, 2.2 pf, SOV 99-090420 Capacitor, Electrolytic, 100 pf, 10V 99-090421 Capacitor, Electrolytic, 220 pf, 10V 99-090422 Capacitor, Electrolytic, 470 pf, 10V 99-090423, Capacitor, Electrolytic, 2200 yf, 16V 99-090424 Capacitor, Electrolytic, 100 pf, 6.3V Miscellaneous 99-090352 Switch, DIP 8 Circuit 99-090163 Crystal, 3.579545 MHz 99-090161 Oscillator, KXO-01-49M152 99-090162 Oscillator, MCO-1425B (49,152 MHz)

4-25

Page 56

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 57

Illustrated Parts Lists

Final Lap Video PCB Assembly Parts List

Part No. Description

Integrated Circuits 99-090108 Integrated Circuit, 74LS00 99-090110 Integrated Circuit, 741504 99-090113 Integrated Circuit, 74F20 99-090114 Integrated Circuit, 741832 99-090115 Integrated Circuit, 741874 99-090120 Integrated Circuit, 741S157 99-090122 Integrated Circuit, 7418173 99-090123, Integrated Circuit, 7418174 99-090125 Integrated Circuit, 7418257 99-090128 Integrated Circuit, 7415374 99-090130 Integrated Circuit, 7418377 99-090131 Integrated Circuit, 7415378 99-090136 Integrated Circuit, TMM2018D-45 (45ns) 99-090244 Integrated Circuit, 7415244 99-090288 Integrated Circuit, 74F04 99-090384 Integrated Circuit, Custom 137 99-090425, Integrated Circuit, 741830 99-090426 Integrated Circuit, 741586 99-090427 Integrated Circuit, 741161 99-090428 Integrated Circuit, 7418541 99-090429 Integrated Circuit, 74F00 99-090430 Integrated Circuit, 74F10 99-090431 Integrated Circuit, 74F32 99-090432 Integrated Circuit, 74F74 99-090433, Integrated Circuit, 74F161 99-090434 Integrated Circuit, 74F175 99-090435 Integrated Circuit, 74F240 99-090436 Integrated Circuit, RAM, TMM2018AP-25 99-090437 Integrated Circuit, RAM, HM6716-25 99-090438 Integrated Circuit, RAM, MB8464-10-SK 99-090439 Integrated Circuit, RAM, MB81464-12 99-090440 Integrated Circuit, Custom 45 99-090441 Integrated Circuit, Custom 106 99-090442 Integrated Circuit, Custom 107 99-090443 Integrated Circuit, Custom 134 99-090444 Integrated Circuit, Custom 135 99-090445, Integrated Circuit, Custom 146 Resistors 99-990193 Resistor, 1 K Ohm, +5%, 1/4 W 99-090332 Resistor, SIP, 1 K Ohm, 1/8 W 99-090406 Resistor, 47 Ohm, 1/4 W 99-090446 Resistor, SIP, 47 Ohm, 1/4 W Capacitors 99-090344 Capacitor, Electrolytic, 470 yf, 10V 99-090447 Capacitor

4-27

Page 58

Illustrated Parts Lists

La, oa f

fo} O°

CRIE - 56DA-3.9605 lo fo} fe}

(2272963200)

oO fe}

Final Lap EMI PCB Assembly 155027-001

Parts List

Part No. Description 99-090448 Filter, EMI, 270 pf, Ferrite 99-090449 Filter, EMI, 2200 pf, Ferrite

4-28

Page 59

This assembly drawing was not available at press time. Contact your Atari Games Customer Service Office for a copy of this drawing.

Figure 4-10 Final Lap Link PCB Assembly Illustrated Parts Lists

155028-001

Parts List

Part No. Description '99-090450 Relay 99-090325 Diode, 181885 99-090451 Switch, Slide

Page 60

Ilustrated Parts Lists Final Lap

N O T E S

4-30

Page 61

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: ‘The active state for is low. ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are yolume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER: A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero, ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentarycontact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). honh= BINARY A number system that expresses all values by using two digits (0 and 1), BIT A binary digit; expressed as 1 or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.

CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system. functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.

Glossary

COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.

CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and. memory.

gll

Page 62

DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage. GATE

  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal Switches another signal on and off.
  • To control the passage of a pulse or signal, HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube. vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode, LOCKOUT COL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (leveis) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC

gl-2 MULTIPLEXER A device that takes several iow-speed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line.

Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic, The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source.

POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR, A device designed to have a definite amount Of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into. four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT » The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.
Page 63

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-dise

players) are free from defects in material and workmanship under normal use

and service for a period of thirty G0) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller's plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller

and Buyer which contract supersedes the terms herein, this warranty is expressed

in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller. :

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your

safety. :

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 64

Atari Games Corporation

675 Sycamore Drive

P.O. Box 361110

Milpitas, California $5035