Midnight Marauders manual
Midnight Marauder (Bally Midway Mfg. Co.) · Manual · 26 pages · 22 sections · original scan
PRELIMINARY
OWNER/OPERATOR'S
MANUAL
MIDNIGHT MARAUDER
re
IDWAY ;
10601 W Belmont Avenue Franklin Park, tilinois 60131 usa.
Phone: (312) 451-9200 Cable Address: MIDCO Telex No.: 72-1596
M05 1-00A12-A023
BLOCK DIAGRAM - MIDNIGHT MARAUDER
CONTROL
MODULES
ss | ss |
DISPLAY
DRIVER ORIVER/REG. MPU INFRASENSE
MODULE MODULE MODULE MPU
facta ee
MODULE
XTNamezL (R)P201
OA1Z2 MIOWIGHI MARAUDERS INSTALLATION
Vieual inspections BEFORE plugging in line cord.
t. Check that all cable connectors are completely seated on printed circuit assemblies. -
- Check that cables ere cleer of a1] moving parts.
- Check for any wires that may have become disconnected.
- Check switches for loose solder or other foreign material that may have come loose in shipment and could cause shorting of contacts.
- Check wires on coils for proper soldering. Cold connections may not show up in factory inspection, but vibration in shipment may break contact.
- Check that fuses are firmly seated and making good contact.
- Check the transformer for any foreign material shorting across wiring lugs.
- Check wiring of transformer to correspond to location voltage. See following illustration.
TRANSFORMER CONNECTION INSTRUCTIONS
REFER TO POWER SUPPLY SCHEMATIC . AUXILIARY TRANSFORMER CONNECTIONS IN GAME MANUAL FOR TABLE *a®
LOCATION VOLTAGE POWER CONNECTOR LOCATION VOLTAGE JUMPER POSITION JUMPER POSITION
| TISVAC | | 2-8, 3-6, 7-10 | TISVAC | : | 2-5 | ||
| TVZ20VAC | 2-8, 4-6, 7-1 | 120VAE | | | 2-6 | ||
| 220VAC | 4-8, 7-9 | I | 220VAC | | | 2-7 | | |
| 2a0VAC | 4-8, 7-11 | [_ 240VAC | | | 2-8 | | |
a
NOTES If the game is to be modified for location voltages higher than 120 volte, MAKE SURE the correct Ballast is used for the Fluorescent Lamp!
PRELIMINARY
MO51-Q0A12-A025
XTName:zL (R)P: 02
OA12 MIDNIGHT MARAUDERS FEATURE OPERATIONS AND SCORING
THE INVADER FEATURE:
The Invader Feature consists of twenty-four invading ships which are blue in color. The twenty-four ships are divided into three groups of eight.
The purpose of these ships is to attack and destroy your bases. They accomplish this by starting at the top of the screen and descending into your bases. It takes three ships making contact with @ base to destroy it.
You destroy the ships by shooting them when lit or by shooting Tank #1 to destroy the ships above Base #1. The same holds true for Tanks #2 and #3.
The attack of the Invaders can be slowed by shooting the Command Ship. This action freezes the Invaders for about four seconds.
THE BASE FEATURE:
The Base Feature consists of three-bases! Base #1, Base #2, and Base # When your three bases are destroyed by taking nine hits (three per base) the Mehds. So----
Defend Your Bases to Survivel
You will receive new bases at 350,000 points per the fgeto t my. This threshold can be adjusted by changing the score in bookkeeping. THE COMMAND SHIP FEATURE: \ The Command Ship is the large ship whi mA Mfront of the Invaders.
Shooting the Command Ship SOS ] Ts for about four seconds. The Command Ship drops shot.
To reise the Comn ge the three tanks and two marauders, so that you may freeze the Invaders aga
THE TANK FEATURE:
The Tank Feature is one of your most important weapons. The lank Feature consists of three Tanks: Tank #1, Tank #2, and Tank #3. Shooting Tank #1 destroys the Invaders above Base #1, Tank #2 for Base #2, and Tank #3 for Base #3. You do receive the points for all the Invaders destroyed by shooting the Tanks.
THE MARAUDERS:
The two Marauder targets complete the sequence for raising the Command Ship.
THE RAPID FIRE FEATURE:
You have Rapid Fire as jong as the Invaders are frozen by the Command Ship.
XTName:L (R)P: 03
SELF - TEST MODE GAME ADJUSTMENTS TABLE
BOOKEEPING FUNCTIONS
The game is designed to help the operator perform certain accounting functions. The game can display the number of total plays and replays (free games). It can display the number of coins dropped down each cain chute. The bookkeeping functions are displayed on the Player display after the bookkeeping location flashes 3 times.
06 ~ 00 to - 40 = Current Credits *07 - 100000 to - 99999 = Total Plays (Plyed & Free Games) *08 ~ 10000 to - 99999 = Total Replays (Free Games) ag - 00 to ~ 99999 = Total times ‘High Score to Date' is beat *10 - 10000 to - 99999 = Total Number of Tickets Awarded (Optional) *11 — 10000 to - 99999 = Coins Dropped thru Right Coin Chute "12 - 10000 to - 99999 = Coins Dropped thru Left Coin Chute ‘a *15 - 00 to - 99999 = MOT USED , e114 - 00 to - 99999 = Number of minutes of Game Play “15 - 00 to - 99999 = Number of Service Credits
e inside of the <Test button at one will flash 01 three Procedure until 06 flashes Each additional press of the e displayed. The game displeys the first bookkeeping entry if the Self-Test! front daor is pressed 15 times. . Alternately push and rel&te second intervals. When the first bookkeeping functi times and display whats in that register location three times. Current credits will then appear o button after a short pause will cause the
After the data in each bookkeeping refiste rded, it can be set to zero simply by pressing switch button S33, locat 4, PU module in the back box, oF by pressing the left Coin Chute switch. Ani u sters can be cleared by alternating between the Self-Test button and the 5 3 on the MPU module or left Coin Chute switch. The Operator is given this go sible convenience and can elect to use or not use it as his needs direct
Pressing the button a\tQmes causes the game to play the power-up tune and light the Game Over Light. For quickbexit from bookkeeping turn game OFF, and then ON again.
Service credits are designed to allow the serviceman to test the game under actual play candidtions without disturbing the bookkeeping records that reside at identification numbers 07, OB, 11 and 12.
To obtain Service Credits, push and release the Self-Test switch until identification number O06 appears in the ‘Display' window. Hold in the Trigger until the desired number of Service Credits (up to five) appears on the player score dieplays.
WOTEs If, upon acceesing identification number 06, 8 number of credits greater than five is displayed, pressing the credit button has no effect.
Identification number 15 is reserved as a record of the number of Service Credits used.
- The 10,000 leve) is Pre-set at the factory; can be set to zero, initially, if desired. es If Coin Chute is not used in game, number displayed (if other than 00) on Player Score displays has no significence.
XTName:L (R) Pz 04
SELF - TEST MIDE Gate ADJUSTMENTS TABLE
VUMIUAELLTTLTA TLL TAAL A TTA ATTA A 1 OVP SAUTOHES LOCATED ON THE Aw PU DUE //////ISIILLI TITS oP swiitcH ADJUSTMENTS
DOINS PER CREDIT RIGHT COIN CHUTE (HINGE SIDE OF COIN DOOR)
# 1COIN 1 CREDIT - 1 COIN 2 CREDITS
1 COIN 3 CREDITS 1 COIN 4 CREDITS
1 COIN 5 CREDITS 1 COIN 6 CREDITS
1 COIN 7 CREDITS
1 COIN 8 CREDITS
1 COIN 9 CREDITS
1 COIN 12 CREDITS
1 COIN 14 CREDITS ** 2 COINS 1 CREDIT
** 2 COINS 2 CREDITS
= 2 COINS 3 CREDITS ** 2 COINS 4 CREDITS"
** 2 COINS 5 CREDITS
CREDITS
CREDITS CREDITS
CREDITS
12 CREDITS
14 CREDITS 3 CREDITS 3 CREDITS 2 COINS
2 COINS
4 COINS
*@ A COINS 3
4 COINS
4 COINS
4 COINS CREDITS
5 CREDITS
7 «CREDITS 7 «CREDITS
3 COINS
4 COINS 5 COINS
5 COINS CREDIT
CREDIT CREDIT
CREDITS Nooo
® SEE FOLLOWING TABLE FOR @ FACTORY RECOMMENDED SETTINGS.
#* NO CREDITS UNTIL 2nd COIN IS DROPPED. SHO SEZ SHES SOA SMES SEG SHAT SHER SHED SAO SHOT SMNZ SHES SHINS
| OF OF | oF | OF | OF |
| ON | OF | OFF | OF OF |
| OFF oN | OF | oF | oF |
| HON | oF | of | oF |
| OF OF | ON | OF | OF |
| a | a | 2 |
OFF oN ON OF OF
| w~ | ON | oN | ar | oF |
| OF OFF | OFF | ON | oF | |
| 1X | OFF | OFF | ON | or |
| ar w | OF | oN | or | |
| nn | ON | OF | ON | or |
| Or OF | ON | oN | oF | |
| a | OX | or | ||
| OFF ON | ON | ON | oF | |
| ON | ON | ON | ON | oF |
| OF OF | OF | OF | WW | |
| CK | OF | GF | OF | Ww |
| OF Ww | OF | OF | oN | |
| nN | OWN | oF | OF | ON |
| OF OF | ON | OF | ||
| Nn | OF | ON | OFF | ON |
| OF WwW | ON | OF | ON | |
| AN | OWN | oN | OF | |
| OF oF | OF | Ow% | ow |
[a ta]
| OF Ow | OF | ON | i) |
| A | ON | OF = oN | oN |
#924 gg99 g292 g9e8
EXPLANATION OF HOW CREDITS ARE AWARDED FOR THESE OPTIONS.
PIRES ILUINIUINZAIRY?
XTNamezL (R)P:05
SELF — TEST MODE GAME ADJUSTMENTS TABLE
witcHu ADJUSTMENTS
COINS PER CREDIT SME1T SHE1G SETI SMEZO SHEZ1 HEZZ SMEZ3 SHEZ4 MHEZS SMEZE SMEZT ‘M428 SAEZ9 SHESO
LEFT COIN CHUTE fr
(LOCK SIDE OF COIN DOOR)
# 1 COIN 1° CREDLT or oF OF OF OF
| V COIN 2° CREDITS | oN | OF ar OF OF |
| 1 COIN 3 CREDITS | OF Ow | oF OF OF |
| 1 COIN 4 CREDITS | on ON | aor OF OF |
CREOITS 5 oF
6 CREDITS oN COIN 7 CREDITS OF 8 CREDITS wn
1 COIN 9 CREDITS ar 1 COIN 12 CREDITS oN 1 COIN 14 CREDITS oF 2 COINS 1 CREDIT ON
2 CREDITS CQINS 3 CREDITS a
s 9299 44934 9999
CREDITS CREDITS zq24 9299 2292 g999
CREDITS COINS 7 CREDITS iq
9 CREDITS 9299 9994 94994
** 2 COINS 12 CREDITS ** 2 COINS 14 CREDITS
- 2 COINS 3 CREDITS
a4 OF ON OF oN
oF ON oF COINS 3 CREDITS ON 22949
4 COINS 3 CREDITS or oF OFF ON
| 4 COINS 5 CREDITS | oN | oF OFF ON |
| 4 COINS 7 CREDITS | OF ON | aor ON |
| 4 COINS 7. CREDITS | an | ow ar om |
eet
| *® 3 COINS 1 CREDIT | or OF Or | ow | on | |
| * 4 COINS 1 CREDIT | ow | OF ON | ww | ON |
| * 5 COINS 1 CREDIT | ar OW | Oo | On | oN |
| = 5 COINS 2 CREDITS | on ON | ON | ON | on |
# TACTORY RECOMMENDED SETTINGS.
- SEE FOLLOWING TABLE FOR EXPLANATION OF HOW CREDITS ARE AWARDED FOR THESE OPTIONS.
= MD CREDITS UNTIL 2nd COIN IS DROPPED.
PIRIELINIUINAIRY
XTName:L (R)P: 06
SELF - TEST MODE GAME ADJUSTMENTS TABLE
I. ‘METHODS IN WHICH CREDITS ARE AWARDED FOR THE FOLLOWING OPTIONS AS NOTED ON THE "DIP SWITCH SETTINGS TABLE" ARE AS
FOLLOWS. See the Figure below.
| 2 COINS | 4 COINS | CREDITS |
| 4 COINS | 3 COINS | CREDIT |
| 4 COINS | 4 COINS | CREDIT |
eee 4 COINS #4445 COINS CREDIT eeeeed COINS #44485 COINS CREDITS
© = 2 COINS 3 CREDITS: Ohe credit issued when Ist # 4 COINS 7 CREDITS: the credit idsued when Ist coin is dropped. Iwo credits issued when 2nd coin is dropped. Two credits issued when 2nd coin is dropped. coin is dropped. wo credits issued when 3rd coin is dropped. Two credits issued when 4th ** = 4 COINS 3 CREDITS: One credit issued when 2nd coin is dropped. coin is dropped. One credit issued when 3rd coin is dropped. One credit’ issued when 4th coin is ## = =3 COINS 1 CREDIT: Ohe credit issued when 3rd dropped. coin is dropped. ©
eee 4 COINS 3 CREDITS: Ohe credit issued when 2nd #44 «4 COINS 1 CREDIT: the credit issued when 4th coin is dropped. Two credits issued when 4th coin is dropped. coin is dropped. #444 5 COINS 1 CREDIT: One credit issued when Sth #242 4 COINS 5 CREDITS: One credit issued when Ist coin is dropped. coin is dropped. One credit issued when 2nd coin is dropped. One credits issued when 3rd coin is #44415 COINS 2 EREDITS: One credit issued when 3rd dropped. Two credits issued when 4th coin is ‘coin is dropped. One credit issued when Sth coin dropped. is dropped.
=exeeq COINS 7 CREDITS: One credit issued when 1st coin is dropped. Two credits issued when 2nd coin is dropped. One credit issued when 3rd coin is dropped. Three credits issued when 4th coin im dropped.
PRELIMINARY
XTName:L (R)P:07
SELF - TEST MODE GAME ADJUSTMENTS TABLE
OIP SwiItcH ADJUSTMENTS GAME FEATURES pS eee ae
IIMTMTTITT TATUM E 11 OVP SANTOHES LOCATED ON THE AS MPU MODULE LIVITITITITITATA TTI AT
COINS PER CREDIT RIGHT COIN CHUTE CHINGE SIDE OF COIN DOOR) .
FLASHES CREDIT LIGHT WHEN CREDITS ARE REMAINING
CREDIT LIGHT STAYS ON WHEN CREDITS ARE REMAINING
(MO GAME OVER ATTRACT VOICE
GAME OVER ATTRACT VOICE SAYS “TRY AGAIN EARTHLING™
DIFFICULTY
DIFFICULTY = CONSERVATIVE SHA SH#2 SHES Stb4 SHES S86 SET SHOR SED <SHO1D SET «S812 SEIS TALS
eS
PROGRESSES. MOTE: IN THE *CONSERVATIVE® DIFFICULTY LEVEL, THE ALIENS ATTACK THE BASES AT A MUCH MORE RAPID PACE AS THE CAME
IP
RELIMINARY
XTName:L (R)P: 08
ROUTINE MAINTENANCE ON LOCATION:
ifeTest routines are written into the game design. They are particularly useful for roune maintenance. The tests are described below. The First test is automatic and occurs on power-up. This test causes the MPU module A4'to examine itself for failures. Seven flashes of an LED indicates praper operation. The second series of self-diagnostic tests causes the MPU to ‘exercise’ each of the other modules in such a way as to make their faults, if any, obvious.
lt is recommended that these tests be used several times a week to check out the games before play. If faults are discovered, they may be corrected on location if the operator has a stock of replacement modules. See "Trouble Shooting on Location",
MPU Module Self-Test:
At power on, the LED on the MPU module flashes once. (Flicker-Flash). After a pause, it flashes six more times then comes on and stays on. A power-up sound is played to announce game readiness. This indicates proper MPU operating condition and successful completion of the power-up test,
Game Self-Diagnostic Tests:
- Pressing the Self-Test button inside the door init switched lamps flash off and on continuously. es the Self-Test routine. All
- Pressing the Self-Test button again causes each digit on the disolay to cycle from 0 thru 9, and repeat continuously.
- Pressing the Self-Test button again causes each solenoid ne at a time, in a continuous sequence. The number appearing on re\asplays is the same as the number assigned to the solenoid. d pulling-in 2s a number appears indicates proper operation. The agse& s improper. !f sound is absent, see the in Solenoid Identificatj
m@oipr’ (Motor 0) to operate, movirs
- Pressing the Self-Test button again causgant them left and right.
5. Pressing the Self-Test butto nN ca Command Ship horizontal motor (Mot
to operate, maying the Shi .
causes the Command Ship vertical motor (Motor 2° + down. To make Further testing simpler you should exit 3 ip’ is at the same level as the bases on the Lamp Sensor revent the limit switches from appearing in the stuck switch test ensors for the sensor test.
- Pressing the Selfste : operate, moving this test when board. This wil and expose all th
- Pressing the Self-Test button again causes the game to enter Ticket Dispensor mode. Once in this mode the Ticket Dispensor (optional) will dispense one ticket each time the gun trigger is pulled.
- Pressing Self-Test button again causes the sound module to play the "Attacker Hit™ sound repeatediy.
- Pressing the Self-Test button again causes the MPU to search each switch assembly for stuck contacts. If any are found, the number of the first set encountered is flashed on the Player Score display. The number remains until the fault is cleared. See the Switch Identification Table for help. Other numbers may follow if more stuck contacts are present. If there are no stuck switches, the Mirror Image display flashes ‘8!
XTName:L (R)P: 9
10.
11. Pressing the Self-Test button again enters the game into sensor test. All the ships on the Lump/Sensor board will lite. By aiming the gun at a snip, the cooresponding lamps whould flicker and then go out indicating that the sensor sees the infra red beam. Ad— ditionally a sensor identifing number will be shown in the display. See the following illuxtration for e detailed layout of the specific Sensor/Lamp locations.
any lights, but should display an The Sensors on the Mechanicel Targets WILL WOT fl appropriate number on the display.
To re-lite the lamps in this mode, operate the left hand coin switch.
Pressing the Self-Test button 19 more times causes the MPU to step thru the threshold and bookkeeping functions described previously end finally to repeat the power-up test. For more rapid exit to power-up, turn the game off, then on. The game is now ready to play.
After successful completion of the Self Diagnostic Test procedure, set the game up for play.
If actuating a switch assembly results in intermittent or no response, clean contacts by gently closing them on @ clean business card or piece of paper and wiping until they wipe clean. Regap, if necessary, to 1/16". Do not burnish or file Gold Plated Switch Contacts.
XTName:L (R)P: 10
TROUBLESHOOTING OW LOCATION
Your game ix designed to make troubleshooting easy. Several simple procedures are given below that cover the greatest percentage of game failures. They are written for an operator a= location and require module replacement. Symptoms and the action to be taken are given for emch type of problem.
If the problem is more complicated and is not solved by following thie procedure, more aetailed procedures are available from Bally/Midway.
1A) SYMPTOM:
ACTION:
ZA) SYMPTOM: ACTION:
CAUTLON:
mB) = SYHFTON: ACTION:
- «SYMPTOM: Game does not play power-up tune when power in turned on. General illumination is present. A) Turn power OFF. Open game's Front Door Assembly by releasing the Letches on it's right side. Locate light emitting diode (LED) on MPU module Ad.
- Turn Power ON. LED must flash 7X to indicate that module Ad is good. Correct flash sequence is flicker/flash-pause-and then six more flashes and LED comes on and stays on. C) If LED does not come on, or does not flash, or flashes, bet less than 7x, turn off power. Check fuses and replace if necessary. D) If fuses are okay replace MPU Module.
Replacement MPU Module must have same Part Number or incorrec peration will result! _See Parts Liat for MPU Module Part Number.
E) If game is correct, it is now ready for play. 1 e n@ correct, (See refer to Module Replacement procedure.
Not all feature lamps light during game A A) Open front door. With power ON, If game is correct, all featur MENON and OFF. B) To gein access to lamps:
- Open Back Door.
- Remove Crater Scener Q in the two “Quick Release" latches.
3. Lift playfie ANY e edge where the 1,000 point lites are
located. €) Replace bu D) If game €) If flash. r is now ready for play. ect, turn power OFF. Replace Driver/Reg- Module A3. id repeat “A.
High vo1\s supplied to the Display Driver Module Al, from the Driver/ReGulator Module AJ}. Wait 30 seconds for High Voltage to Bleed Off.
F) If game is correct, it is now ready for play. ©) If game is not correct, turn power OFF. Replace HPU module AG. See
One or some switched lamps always ON. Repeat 2AA, AB, AE, and AF and if necessary AG & AH.
Display digits improper. One or several segments always OFF, digits mottled or several segments or digit(s) always ON.
XTName:L (R)P2 11
ACTION: A) Open front door. With power ON, press button (Self-Test awitch) twice. If the game is correct, each digit on the Mirror Image Display Driver Module Al displays the count 1-9 and O continuously in each of the 6 digit positions. Note defect in Display Driver module.
- Turn power OFF. See CAUTION NOTE 2AE. C) Replace Display Driver module Al. Turn power ON. Repeat A. D) If game is correct, it is now ready for play. If geme is not correct, refer to Hodule Replacement procedure. (See Parts List). E) Replace MPU module AG. See CAUTION NOTE, 1AD. Turn power ON. Repeat A.
@A) SYMPTOM: Solenoid(s) do(es) not pull-in during course of game. ACTION: A) Open front door. With power ON, press button (Self-lest switch) three times. B) If game was correct, each solenoid would be energized. A number is flashed on the ‘Player Score display as each solenoid is pulsed. Note any numbers that do not have the sound of a solenoid associated. See Solenoid Identification Table. C) Refer to 2AB 1& 2. Turn power OFF. Inspect the solenoid. D) If a lead is broken off, repair. Repeat A & B. If game ts correct, it is now ready for play. If solenoid wiring was correct, turn power OFF. E) Replace Driver/Regulator module A3. See CAUTION NOTE 2AE. F) Repeat AA & AB. If game is correct, it is now ready to play. If game ia not correct, turn power OFF. &) Disconnect Sound Module. H) Repeat AA & ABy If game is correct replace sound correct. It is now ready to play. If game is nok OFF. : I) Replace HPU module Ad. See CAUTION NOTE
- Repeat A & B. If game is correct, > not correct, refer to Module Reg : game is t,\pbron power
f Oo play. If game is re. (See Parts List).
Shooting to one minute with power OFF. Repeat as necessary. AE, AF, AG, AH and if necessary, Al,
- SYMPTOM: Solenoid(s) always energized power ON, followed by five Replace damaged solen . Ad.
SA) SYMPTOM: Motor(s) da during course of game. ACTION: A) Op ith power ON, press button (Self-lest switch) 4, 5, ° turn on each Motor individually. B) If @ idcorrect the tank motor will operate first, then the command shi Sorizontal motor, and finally the command ship vertical motor.
5B) SYMPTOM: No motors cperate during test and no sensors score points during game play. ACTION: A) Check fuse F2 on Driver/Reg. Module A3. If fuse is good. Turn off game. B) 1f fuse is blown replace F2 with a 4 amp 3AG fuse. Repeat SAA & AB. If e is correct, it is mow ready for play. If game is not correct turn game OFF. C) Replace Driver/Reg. Module A3. See CAUTION NOTE 2AE. D) Repeat SAA & AB. If game is correct, it is now ready for play. If game is not correct, turn game OFF.
XTNameiL (R)P: 12
TA)
BA)
mA) SYWP TOM: ACTION:
SYMPTOM:
ACTION:
SYMPTOM: ACTION:
SYHPION: ACTIGR: E) Replace infrasense MPU. F) Repeat SAA & AB. If game is not correct turn game OFF and consult the factory.
No Sound. A) Open front door. With power ON, press (Self-Test switch) 8 times. 8B) Turn volume control clockwise to Max. C) If correct, sound will be heard. If incorrect, try seating speaker lead connector (J2) and input connector (J1). D) If correct, sound will be heard. If incorrect, refer to MOdule Replacement procedure.
Trigger does not work or command ship vertical motor does not change direction. A) Open front door. With power ON, prese (Self-Test switch) 9 times. B) Open the back door and by hand, disengage the gear controlling up-down movement of the command shift. While holding the gear away from the spring, slide the ship forward approximately three inches “and release the gear. This should lock the command ship in place and ineure the limit switches are not actuated. C) If the game is correct, the Mirror Image Display will flash ‘O". If a number appears on the display, See Switch Assembly Identification Table. ) Verify switch operation by squeezing the trigger several times and by igengaging the gear and moving the command ship to its upper and lower : In each case an appropriate number should appear on the Mirror w/) hich coorespends to the Switch Assembly Identification Target(s) do f A) Open front dooMd fy times. B) All target lites should com¥& €) Aim the gun at the suspected sensd qhorpspending lamps should go y-f fee Sensor Identification play. esemhutton (Self-Test Switch) 10
out and a number will appear in the disf Table. To re-lite-Lamps, operate Left Hand Coin Switch. D) If the game is correct, it is now ready for pl correct turn power OFF. E) Check connectors on Lamp/Sensor Board to insure they are properly seated. Also visually check sensors to make sure they haven't been bent out of alignment. F) Repeat steps AA thru AC. ©) If game is correct, it is now ready to play. If game is not correct, If game ie not
turn power OFF. H) Replace Lamp/Sensor Boerd. I) Repeat steps AA thru AC.
- If the game is correct, it is now ready for play. If game ia not correct, turn power OFF. K) Replace infrasense MPU. L) Repeat steps AA thru AC. M) If the game is correct, it is now ready to play. If game is not correct, turn power OFF and consult the factory.
Game blows fuse(e) repeatedly. See Module Replacement Procedure. F.O. 560-3.
XTName:L (R)P: 13
The following table is # guide in tracing signals from the Sensors to the inputs on the Infrasense Board.
Lemp/Sensor Infrasense Sensors ¢ Transistor #@ Connector/Pin Conn./Pin
| 1 | Qi | J3-1 | J3-2 | |
| 2 | Q2 | 33-2 | J3-3 | |
| 3 | Q3 | 33-3 | J3-4 | |
| 4 | Qa | J3-4 | J3-6 | |
| 5 | Qs | J3-5 | J3-7 | |
| 6 | Qé | J3-6 | 33-8 | |
| 7 | Q7 | J3-7 | 33-9 | |
| 8 | Qs | J3-8 | 33-10 | |
| 9 | Qo | J3-9 | J3-11 | |
| 10 | Q10 | J3-10 | J3-12 | |
| VW | Qi | J3-11 | J3-13 | |
| 12 | Q12 | J3-12 | J3-14 | |
| 13 | Qi3 | 33-13 | J3-15 | |
| V4 | Q14 | I-14 | J3-16 | |
| 15 | Qis | J3-15 | J3-17 | |
| 16 | Q16 | J3-16 | J3-18 | |
| 17 | Q17 | 33-17 | J3-1 | |
| 18 | aie | J3-18 | J4-2 | |
| 19 | Qig9 | 33-19 | J4-3 | |
| 20 | Q20 | 33-20 | 34-4 | |
| 21 | Q21 | 33-21 | J4-5 | |
| 22 | Q22 | J3-22 | 34-6 | |
| 23 | Q23 | J3-23 | J4-7 | |
| 24 | Q24 | J3-26 | 34-8 | |
| 25 | Q2z5 | RIGHT MARAUDER (MIRROR) | J4-11 | |
| 26 | Q26 | LEFT MARAUDER (MIRROR) | J4-12 | |
| 27 | Q27 | RIGHT TANK | (MIRROR) | J4-13 |
| 28 | Q28 | CENTER TANK | J4-14 | |
| 29 | Q29 | LEFT TANK | (MIRROR) | 34-15 |
| 30 | Q30 | CQMMAND SHIP | 34-16 | |
| 31 | N/U | N/U | J4-17 | |
| 32 | N/U | N/U | 34-18 |
To verify continuity of any questionable sensor, place game in target sensor test as Previously described in the manual. Then clip a long jumper to the suspected transistor emitter, the appropriate number should be displayed on the mirror image display. If the number does not appear, use the table above to determine the reason fot lack of continuity. If the number appears when the emitter is probed but not when the gun is aimed at the sensor either the sensor is bent out of xlignment or the transistor is defective.
[PRI ILUIMIUIN ALR
tL (R)P: 14 XTName=L (R) SOLENOID INDENTIFICATION TABLE (MIRROR VIEW)
Self leat € Solenoid Identification
01 Explosion Lights (No Solenoid Sound) 02 Right Merauder 03 Left Marauder 04 Right Tank os Center Tank 06 Left Tank u7 Command Ship Descend
SWITCH ASSEMBLY SELF-TEST DISPLAY NUMBERS
Switch Self Test # Description
01 Trigger 09 Coin Chute Left 10 Coin Chute Right 12 Stam 15 Lower Limit - Command Ship 16 Upper Limit - Command Ship
PRELIMINARY
XTName:L (R)P: 15
PART LIST MIDNIGHT MARAUDER
MISCELLANEOUS
TRANSFORMER M100-00109-A000 AUXILLIARY TRANSFORMER MTO00-00132-A000 BULBS CMB8-244 0017-00003-0519 BULBS #555 0017-00003-0484 BULBS #912 0017-00003-0525 BULB FISTBBLB (FLUORESCENT) 0017-00003-0095 STARTER 0017-00003-0412 MOTOR (2) HORIZONTAL MOTION 0040-00625-0100 MOTOR (1) VERTICAL MOTION 0040-00622-0000 FUSE (2) LAMP 3AG FLUORESCENT LAMP & AUX TRANSFORMER 0017-00003-0001
ASSEMBLY COILS
RIGHT ALIEN AA12-00065-0000 LEFT ALIEN AA12-00065-0000 RIGHT TANK AA12-00065-0000
CENTER TANK AA12-00065-0000 LEFT TANK AA12-00065-0000 COMMAND SHIP -DESCEND AA12-00071-0000
MODULES
*"220R IMAGE DISPLAY A084-91713-B000 EXP RASENSE MPU A084-91681-DA12 DRIVER/REGULATOR A0B4-91678-EA12 MOTOR CONTROL A0B4-91682-GA12 SQUAWK & TALK A084-91625-AA12 MPU A0B4-91494-AA12 LAMP/SENSOR A084-91697-CA12 TARGET SENSOR A0B4-91707-BA12
POWER MCDULE A084-91492-A000 TRANSFORMER & RECTIFIER ASSEMBLY AA12-00037-0000
PLS LIMINARY
SENSOR IDENTIFICATION TABLE (MIRROR IMAGE)
SENSOR # DESCRIPTION
25 RIGHT ALIEN 26 LEFT ALIEN 27 RIGHT TANK 28 CENTER TANK 29 LEFT TANK 30 COMMAND SHIP
PRELIMINARY
billy MIDWAY isco
May 15, 1984
SERVICE BULLETIN
GAME: MIDNIGHT MARAUDERS
SUBJECT: P.C. BOARD INTERCHANGEABILITY
The following P.C. Boards have been used before in Bally Midway Pinball Games.
P.C. BOARD INTERCHANGEABLE WITH
- MPU Module Any Bally Midway Pinball Game to date. (Except Program IC's and Jumper
Combinations .)
- Squawk & Talk Module Any Bally Midway Pinball Game to date that uses the Squawk and Talk Module. (Except Program IC's and Jumper Combinations.)
- Rectifier/Power Supply Gold Ball and Grand Slam Module
Attacheé is a preliminary parts list for Midnight Marauders.
Pete Gustafson
PG/dd
attach. —S) 40604 W. Belmont Ave. « Frankin Park, llinois 60431 » Telephone (342) 454-9200 + Telex: 72-1596 Of
Service Bulletin May 15, 1984 Page 2
PRELIMINARY PARTS LIST
MIDNIGHT MARAUDERS
MISCELLANEOUS
Transformer Auxiliary Transformer Bulbs CM8-244 or 86 Bulbs #555 Bulbs #912 Bulb FI5T8BLB (Fluorescent) Starter Motor (2) Horizontal Motion Motor (1) Vertical Motion Fuse (2) Lamp 3AG Fluorescent Lamp and Auxiliary Transformer
ASSEMBLY COILS
Right Alien Left Alien Right Tank Center Tank Left Tank Command Ship Descend
MODULES
Mirror Image Display Infrasense MPU Driver/Regulator Motor Control Squawk & Talk MPU Lamp/Sensor Target Sensor Power Module Transformer & Rectifier Assembly Trigger LED (In Gun-Assembly) MTO0—00109—A000 MT00-00132-A000 0017-00003-0519 0017-00003-0484 0017-00003-0525 0017-00003-0095 0017-00003-0412 0040-00625-0100 0040-00622-0000
0017-00003-0001
2AA12-00065-0000 BAL2-00065-0000 BA12-00065-0000 BA12-00065-0000 BA12-00065-0000 AA12-00071-0000
O084—91713-B000 A084-91681-DA12 AO84-91678-FA12 BO084-91682-GA12 AO84-91625-AA12 A084-91494-AA12 A084-91697-CA12 A084-91707-BA12 A084-91492-A000 AA12-00037-0000 A084-91708-AA12
74 -181-M]
AMONG BLUM / VSN en an conf a8 (on08 LaVLNaMOR
Epa! | OPIS sug ae ci
ar etrice it i
(TET
DISPLAY DIGIT ENABLE
=
-&
a
amy
x PAT HGH VOCTACE |
DIGIT DRIVERS (@)
- + + te io RB BI no n+ Re J . cz << {ait @Io ae @a Dh
Ree tne ih nas SRT mae SRS mt Ad nae ™ as ras wo ros wl roe wee} Ql RBs:
1 _ ] _ 1] 1
RB 3h RIS,
ISK F 300K (SENET PRVERS
Qs’ :
NOTES! LLUNLESS OTHERWISE SPECIFIED ALL RESISTORS ARE 5%, Y4W. @PREFIX ALL REFERENCE DESIG.WITH ASSEMBLY REFERENCE LESIG."A!”
3, ¥ INDICATES ‘AID’ TEST POINT,
(avaaim } ¥en ~1000- v0.0 cc (G78) lta -8¥ AYORDREY RDS MBA ey 8, $$ $$$“
ag sz From _[ ow [wine "Gaal PORUIRTORING CORP, =
VOLTAGE REGULATOR/ SOLENOD DRIVER P/O A3
ser's nly @NeQd
LAMP ORIVER P/O AB
HETIL gad Cr ITTV R225
+5V
DIRECTION 4 >— SPEED rn 7 cT PROMCT ENe: M. STEINMETZ useD ON MIDN'T MARAUDER no.RtgD | PER Za [wise .MFG.CO, FRANKLIN HLL
SCHEMATIC OWG.
MOTOR CONTROL
A080 - 91682 -HAIZ
PART mo,
MOBI — ooAl2 ~ MOIS