Football TM-126 2nd Printing
Football (Taito do Brasil, 1981) · Technical Manual · 116 pages · 49 sections · original scan
} sued payessniiy UM eje}dwWo5 Jenuey| ddIAlag pue soueuDazUle| ‘UOI}eIOdO I LVL l
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the TV monitor chassis and on the label located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service.
LOO ON awvd,
FOOTBALL Operation, Maintenance and Service Manual
Complete with Illustrated Parts Catalog
ATARI INC 1265 BORREGAS AVENUE RO. BOX 9027 SUNNYVALE, CALIFORNIA 94086, 408/745-2000 * TELEX 35-7488
A
ATARI
A Warner Communications Company
Copyright © 1978 by Atari, Inc. All rights reserved
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission requests, write:
ATARI INC 1265 Borregas Avenue P.O. Box 9027 Sunnyvale, California 94086
NG Lithographed in the U.S.A.
TABLE OF CONTENTS
1 LOCATION SETUP A, INTRODUCTION.........00 000000000 eee wee a weeeee Ll B. GAMEINSPECTION......... 1-3 C. INSTALLATION REQUIREMENTS . 1-4 Line Voltage Selection : 1-4 Type of Power Cord 2.0... 6 cee eee een nee 1-4 D, INTERLOCK, POWER ON/OFF SWITCH AND OTHER RELATED OPERATOR CONTROLS Interlock Switch Checkout Procedure .......0 0.0000 eee e eee ee .. 15 E. OPERATOR OPTIONS .. . 1-7 F, SELF-TEST PROCEDURE .. 18 G. VOLUME CONTROL .......0 00066 c cc cence eee 1-8
2 GAME PLAY A. INTRODUCTION «2.0. .00.0 0000 cccceveeseeveececeeeveteveeess 21 B. PLAYERCONTROL PANEL . 2-2 The Play Select Board .... C. ATTRACTMODE..... D. READYTOPLAY MODE . 26 E. PLAYMODE .... 26 Plays Offensive Running Plays A. The Sweep Play . The Keeper Play... 2-6 Offensive Passing Plays . ... 2-6 The Bomb Play ..... 26 The Down and Out Play 2-6 Defensive Running Plays . 2-6 The Sweep Play ... 26 The Keeper Play... .. 29 Defensive Passing Plays . 2-9 The Bomb Play .... 2-9 The Down and Out Play 2.9 The Four Goal Deterrents . . 29 Time Penalty 2-9 The Touchdown . : : : : 29 TREDOWNS . cgcv 5. toes ed ces nent sees tenet ten cues seems 2-16
3 THEORY OF OPERATION A GENERAL INFORMATION ..........0 200-0000 cece e eee 3-1 B. POWER SUPPLY : 5 C. MICROPROCESSOR CIRCUITRY ............--..255 MPU, ROM and RAM 3 Address Decoding «00... ice cece cette cent neeee nee F
ii
TABLE OF CONTENTS
FOClock Driver Watchdog Reset SYNC GENERATOR . ALPHANUMERIC GENERATOR . SCROLLFIELD GENERATOR .. MOTION OBJECT GENERATOR . TRACKBALL CONTROL AND S WITCH INPUT CIRCUITRY VIDEO OUTPUT. . : : AUDIO GENERATOR AND AMPLIFIER... 200.0000 0c cece eee 3 4 MAINTENANCE AND ADJUSTMENT CLEANING cece - B. COIN MECHANISM . Components on Coin Door Dea s-roamms
Access to Coin Mechanisms ........0 0-00 e cee eee o1. 42 - Cleaning of Coin Paths . . . 4-3 - Lubrication . 43 . Adjustment of Coin Switch Trip Wire . 4-3 Mechanical Adjustments on Coin Mechanism . . 44 General Troubleshooting Hint... . 44 C. TV MONITOR ADJUSTMENTS . - 46 D. FUSE REPLACEMENT . 46 E. TVMONITOR REMOVAL .. we - 4-7 F. CONTROL PANEL REMOVAL ... - 4-7 G. TRACKBALL ASSEMBLY REMOVA 47 . H. PLAY SELECT BOARD ASSEMBLY REMOVAL : : 14-7 - I. LED (LICON) PLAY SELECT/PASS SWITCH REMOVAL ............. 4-10 Jd. BASE ASSEMBLY REMOVAL... ...-.0 0.000600 c cece eects 4-10 - 5 ILLUSTRATED PARTS CATALOG
LIST OF ILLUSTRATIONS
Figure 1-1 Football Control Panel . . BBs FEA eens Figure 1-2 Football Cabinet Assembly . Figure 1-3. AC Line Voltage Check ...... Figure 1-4 Voltage-Selection Connectors . Figure 1-5 Location Set-Up Requirements . Figure 1-6 Location of Interlock and Power On/Off Switches . Figure 1-7 Option DIP Switches and Game PCB Location and Removal . Figure 1-8 Location of Switch Self-Test and Volume Control . Figure 2-1 Player Control Panel Figure 2-2 Play Select Board Display. . . Figure 2-3 Attract Mode Figure 2-4 Ready to Play Mode . . coeds Figure 2-5 The Sweep, An Offensive Running Play .........0.0.000 00000 eee uee a
ahprare Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16 Figure 2-17 Figure 2-18 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10
Figure 3-11 Figure 3-12 Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16 Figure 3-17 Figure 3-18 Figure 3-19 Figure 3-20 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9 LIST OF ILLUSTRATIONS
The Keeper, An Offensive Running Play The Bomb, An Offensive Passing Play . . The Down and Out, An Offensive Passing Play. The Sweep, A Defense The Keeper, A Defense. . The Bomb, A Defense The Down and Out, A Defense . Incomplete Out of Bounds Tackled Offense Intercept . . Touchdown . . Down Marker Location Football Game Block Diagram . . Football PCB Bleck Diagram .. . (On-Board) Power Supply Schematic Diagram . Power Supply Simplified Block Diagram Microprocessor.Schematic Diagram .. . Memory Block Diagram Address Decoding Schematic Diagram . FO Clock Driver Signal Sync Generator Schematic Diagram Simplified Block Diagram of Crystal-Controlled Oscillator 3-12 and TV Sync Circuitry Horizontal Sync Timing Diagram . Vertical Sync Timing Diagram . . Alphanumerics Generator Block Diagram Alphanumerics Generator Simplified Schematic Diagram . 1. 3 Scrollfield Generator Block Diagram and Simplified Schematic Diagram - 3-17 Display RAM Simplified Schematic Diagram beens . Motion Object Generator Block Diagram. ...... . Trackball Control and Switch Input Simplified Schematic Diagram dewens 3-20 Video Circuit Simplified Schematic Diagram .... 000.0000 0 eevee 3-21 Audio Generator and Amplifier Simplified Schematic Diagram .......- 3-22 Coin Door Assembly Hinging Open the Magnet Gate Assembly Removal of Coin Mechanism .......... Surfaces to Clean Inside the Coin Mechanism Removal of Plate Covering Rear of Coin Slot . Close-up View of Lubrication Point Detail View of Coin Switch and Trip Wire Adjustments on Coin Mechanism ..... . Locations of Adjustments on TV Chassis
LIST OF ILLUSTRATIONS
Figure 4-10 Figure 4-11 Figure 4-12 Figure 4-13 Figure 4-14 Figure 4-15 Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8 Figure 5-9 Figure 5-10 Figure 5-11 Figure 5-12 Figure 5-13 Figure 5-14 Figure 5-15 Figure 5-16 Figure 5-17 Figure 5-18 Control Panel Removal TV Monitor Removal ....... : Trackball Assembly Removal... ... Play Select Board Assembly Removal . . LED (LICON) Play Select/Pass Switch Removal . Base Assembly Removal Football Final Assembly TV Monitor Assembly . . Type B Power Supply Coin Door Assembly Front Bezel Assembly . . Coin Lockout Assembly Coin Switch Assembly Control Panel Assembly Trackball Assembly : Strain Relief Cord Assembly . On/Off Switch Assembly... . . Self-Test Switch/Volume Bracket Assembly . Interlock Switch Assembly ...... LED Pushbutton Switch Assembly (Red) . Rectifier PCB Assembly .... 5-20 Play Select PCB Assembly . . 5-21 RF Shield PCB Assembly... . . Football PCB Assembly
LIST OF TABLES
Table 1-1 Table 1-2 Table 1-3 Table 3-1 Table 3-2 Installation Requirements Operator Options Self-Test Procedure MPU Input/Output Signal Descriptions Atari Inc. Programmable Memory Map
LIST OF APPENDICES
Appendix A_ Reference Schematic Diagrams Appendix B Atari Customer Service Information
vi
A. INTRODUCTION Football is a two-player game developed by Atari, Inc. The game is packaged in a cocktail cabinet, graphically illustrated with football plays and action figures. The 19-inch TV monitor displays the different football plays while in the attract mode, enhancing the attraction for passing poiential players.
Player-operated controls are mounted on either side of the screen (end zones) which allows proper player orientation (opposing teams) during the play mode. This is illustrated in Figure 1-1. The player controls consist of a Play/Pass LED pushbutton switch and a Player Track Ball. The ball smoothly rolls at the shove from the palm of your hand; this moves either your defensive or offensive man any place on the screen within the goal and boundary lines. FOOTBALL
TOP VIEW OF CABINET
(PLAYER ONE)
£3) 09 6 nakoa PLAYER TWO F DIRECTION : : TOWARD
- tM _ GOAL LINE
: : PLAYFIELD PLAYER ONE ————
| DIRECTION | : | : |
| TOWARD | ; | , |
| GOAL LINE | : | : |
: 7
Si
PLAY/PASS PusweurTon eLeey
PLAY SELECT TRACK BALL
DISPLAY PLAYER
CONTROL
(PLAYER TWO)
Figure 1-1 Football Control Panel
1-2 FOOTBALL
TRACK BALL PLAYFIELD
PLAYER CONTROL
MAIN CABINET ASSEMBLY
COIN DOOR
BASE ASSEMBLY (REMOVABLE) TRACK BALL PLAYER CONTROL
Figure 1-2 Football Cabinet Assembly
The coin mechanism on the front mid-portion of the game cabinet, below the table top as illustrated in Figure 1-1, initiates the play, when a coin or coins are deposited. The cash box is located behind a locked access door. The Football cabinet is shipped to you with an optional wood base as illustrated in Figure 1-2. This base is initially mounted at the factory for shipping convenience.
The Football game is another unique concept developed by Atari, which provides the illusion of realism, the realism of action as the players scrimmage and battle for the goal line. The competitive participation of the two opposing players increases as they put their spirit into the track ball.
The object of your Atari Football game is for the offensive player (displayed as O’s) to score a touchdown at the goal line. This goal line is at the end zone away from the offensive player. The offensive player in possession of the ball must travel or run in the forward direction regardless of which control panel is being used.
The defensive player (displayed as X’s) must keep the offense from reaching the goal line. The offensive player has the ability to scheme and maneuver his plays by selecting one of the four plays available at his or her control panel (2 pass plays and 2 running plays—see Chapter 2). The defense must out-guess the offensive opponent to either gain possession of the ball or block the opponent’s path to the goal line. When the defense gains possession of the ball the X’s change to O's and vice versa. The interchange continues as the offense tries to score and the defense attempts to stop the offense and regain possession of the ball. B. GAME INSPECTION Your new Football game is manufactured ready to play immediately after removal from the shipping carton. Your cooperation is desired in order to supply the final touch of quality control to your game. Therefore, please follow the procedures below to ensure that your game is in perfect condition:
- Examine all external parts of the game cabinet for dents, chips, or broken parts.
- After determining that the game has been received in good condition, unlock and open the access door located to the right of the cabinet while facing the coin door, just under the table top. Carefully inspect the interior and verify the following: a. All plug-in connectors are firmly seated. b. Remove game PCB as instructed in steps 1-4 of Section E.
FOOTBALL 1-3
c. All integrated circuit packages (chips, ICs) in sockets on the game printed circuit board are firmly seated. d. Replace game PCB as instructed in step 6 of Section E. e. The fuses are all seated snugly in their holders. f. No harness wires are disconnected. g. No loose foreign objects should be present, especially metal objects that could cause electrical problems.
Be sure all the major assemblies are checked. Check the game printed circuit board (PCB), the transformer (located on the power supply chassis inside the game cabinet), the speaker, and player controls. Also, be certain that the TV monitor is securely mounted.
Check the serial number located on the metallic label in the upper left-hand corner on the back of the game cabinet or the opposite side of the coin door side. The serial number also appears in the corner (common to both edge connectors) on the back of the PCB, inside the game cabinet. See the illustration on the inside front cover of this manual.
C. INSTALLATION
REQUIREMENTS
Voltage Selection Your Football game is shipped for operation at 110 VAC, 60 Hz. IF YOUR LOCAL LINE VOLTAGE IS 110 VAC, perform the following steps:
- Measure AC line voltage with an AC voltmeter as in Figure 1-3.
- If AC line voltage is consistently below 100 VAC, plug in the black low-voltage connection, on the power supply chassis. See Figure 1-4.
- If AC line voltage is approximately 110 VAC, plug in the orange connection (factory installed).
IF YOUR LOCAL LINE VOLTAGE IS NOT 110 VAC, BUT INSTEAD IS 220 VAC, perform the following steps:
- Measure AC line voltage with an AC voltmeter as in Figure 1-3.
- If AC line voltage is consistently below 210 VAC, plug in the green low-voltage connection. See Figure 1-4.
- If AC line voltage is approximately 220 VAC, plug in the red connection.
Type of Power Cord Atari has added a strain-relief cord to your Football game. The advantage of this type of cord is that if pulled accidentally, the strain-relief will hold the cord in place at the cabinet wall. The plastic strain relief “cushions” the impact of the shock and prevents the cord from pulling the wires out of the harness connector.
SET TO AC VOLTS AC OUTLET
Figure 1-3 AC Line Voltage Check
1-4 FOOTBALL
VOLTAGE-SELECTION | CONNECTOR WIRE COLOR BLACK ORANGE | installed at factor LINE VOLTAGE [__ 95 VAC 110 VAC
220 VAC
ORANGE CONNECTOR (FACTORY- INSTALLED)
Ty ®
ON/OFF AND Co INTERLOCK 'n SWITCH
Slow - biow 8 it 4 VOLTAGE SELECTION = fae en CONNECTOR
2.5 Amp.125V.
POWER SUPPLY CHASSIS
Figure 1-4 Voltage-Selection Connectors
Table 1-1 Installation Requirements
POWER REQUIREMENTS. Power Supply’ 110 VAC @ 60 Hz 220 VAC @ 50 Hz
TEMPERATURE RANGE On Location and in Storage: No lower than Q degrees Celsius (32 degrees Fahrenheit)
HUMIDITY RANGE Relative Humidity No more than 95%
LOCATION SPACE REQUIREMENTS *
39.25 Inches (99.7 Centimeters) 44.00 inches (111.8 Centimeters) 25,25 Inches (64.14 Centimeters) Height, Width: Dept.
TV MONITOR 19-Inch Black and White
*See Figure 1-5
D. INTERLOCK, POWER
ON/OFF SWITCH AND OTHER OPERATOR CONTROLS
To minimize the hazard of electrical shock while you are working on the inside of the game cabinet, two interlock switches have been installed. (See Figure 1-6). One is located behind the access door and one behind the coin door. These switches remove all the AC line power from the game circuitry while the doors remain open.
Interlock Switch Checkout Procedure Check for proper operation of the interlock switches by performing the following steps:
- Unlock and open the rear access door and the coin door.
- Plug the AC line power cord into your local AC outlet (110 VAC or 220 VAC).
FOOTBALL 1-5
44” (111.8 CENTIMETERS)
39.25” (99.7 CENTIMETERS)
INTERLOCK SWITCH
POWER ON/OFF SWITCH
Figure 1-6 Location of Interlock and Power On/Off Switches
1-6 FOOTBALL
Y4-TURN FASTENERS | RF SHIELD PCB
ee EBA EBH
DIP SWITCHES
GAME PCB
a Figure 1-7 Option DIP Switches and Game PCB Location and Removal
| 3. | Set the power On/Off switch to the “On” position. | production. To determine how the switches have been |
| 4. | Close the access and coin door. Within approx- | set for your game, compare the attract mode (Chapter 2, |
imately 30 seconds after closing the last door to Section B) with the information in Table 1-2. the game cabinet the TV monitor should display a picture. To change the toggle positions of the switch assembly
| 5. | Slowly open either door to the game cabinet, and | and set the desired options, the printed circuit board |
the TV picture should disappear when either the {PCB) must be removed according to the following pro-
access door or coin door is opened to approx- cedures:
imately one inch.
- If the results of step 5 are satisfactory, the interlock switches are operating properly. If the picture
This game includes a new style of easy-access does not disappear as described, check to see if PCB. The radio frequency shield has been the corresponding interlock switch is broken from redesigned to use only three individual its mounting or stuck in the “On” position. quarter-turn fasteners as a direct result of field
| 7. | Close and lock both doors. | input. | |
| E. | OPERATOR OPTIONS | 1. | Switch the game power on/off switch io “off” and |
The operator options offer maximum player appeal for open the access door.
| your game location(s). These options are listed in Table | 2. | Locate the radio frequency (RF) shield assembly |
1-2. They are preset for a certain game set-up during immediately inside the game cabinet behind the
FOOTBALL 1-7
VOLUME DECREASE: COUNTER- CLOCKWISE
SELF-TEST-SWITCH
VOLUME CONTROL
Figure 1-8 Location of Self-Test Switch and Volume Control
access door (see Figure 1-7). This assembly is an aluminum box with hundreds of holes. On one end of the assembly is a small PCB with an edge connector coming from the edge of the Football game PCB.
- Turn the three individual quarter-turn fasteners on the RF shield PCB 1/-turn to the left or counterclockwise.
- Carefully pull out the Football game PCB and the FF shield board together as a unit. These would not normally need to be separated when merely making option switch changes.
- Set the switches for the desired options as listed in Table 1-2.
- Replace both PCBs by following steps 1 through 4 in reverse order. Do not force or bend the game PCB. Before replacing, inspect the PCB for damage.
- Close and lock the access door.
1-8 FOOTBALL
- Plug in the game and verify that all options function by playing the game.
F. SELF-TEST PROCEDURE
Football will test itself and provide data to demonstrate that the game’s circuitry and controls are working properly. This procedure uses the TV monitor and the speaker; no additional equipment is required. See Figure 1-8 for location of the Self-Test switch. To start the procedure, slide this switch to “on” as indicated in the figure. See Table 1-3 for further details and instructions on the Self- Test. We suggest that you run the Self-Test each time the coin box is opened.
G. VOLUME CONTROL If volume is incorrect for your location, open the coin door and adjust the volume control as indicated in Figure 1-8.
Table 1-2 Option Settings
Switch Settings on 4 Toggle DIP Switch en (located at position K10 on the Game PCB) RESULT
| 1 | 2/3 | 4 | ||
| Coin Length | ON | ONT | Nor | (A) 1% Minutes/Coin |
| ON | OFF | {B) 2. Minutes/Coin |
ore on | USED (C) 2¥2 Minutes/Coin OFF OFF (D) 3. Minutes/Coin
Table 1-3 Self-Test
| Instruction | Result if Test Passes | Result if Test Fails |
PRELIMINARY Not Applicable Not Applicable
Set volume level potentiometer (located on a bracket immediately behind and to the right of the coin door) to ¥2 volume.
RAM AND ROM TEST TV monitor displays ROM OK RAM OK | I the RAM does not check correctly,
| Set Sel-test slide switch (located | | as illustrated below | the screen will display the message |
above the volume potentiometer , immediately behind and to the BAD RAM: right of the coin door) to the “on” Ifthe ROM is a fault, position. BAD RAM appears on the screen. There are three ROMs in Football (Program ROMS 1, 2,3).
| SCROLLFIELD TEST | Scrolifield | scrolls | in | the | direction |_| | No scroliield motion, |
Press the “Play Select” pushbutton | towards the player, regardless of which switch on either control panel. play select switeh was pressed.
| ‘TRAK BALL™ TEST | An “X" or “O" character will move | “X" or “O” character (or both) not |
| Roll the Trak Ball!™ in random | around within the entire area of the | displayed |
| motion and observe TV monitor | | scrolfield. | {kt is irrelevani to the test |
| screen, | Either player's Trak Ball | | which Trak Ball controls the X or the |
will do. 0) Player should move. Crowd sound intensifies as each switch | No crowd sound (indicates logic cir
| AUDIO TEST | held on | cuitry malfunction) |
Press each switch successively and hold it on (play select, slam, Crowd sound does not intensify (inoption, etc.) dicates possibilty that switch is bad). See next test
‘SWITCH AND LAMP TEST Each pressed switch generates an audi | No beep sound. Press all the following switches: ble “Beep"—one beep when pressed Slam, Coin Switches (2), Play and a second beep when released. Select Switch. All LEDs dark, all lamps lighted. Either some or all lamps are out.
Back-lighted play select board lamps are lighted
| OPTION SWITCH TEST | The active option switch setting is | No switch setting display or display in |
The option switches 1 and 2 have | displayed below the ROM OK at the top } correctly matching the actual setting, ‘a special test feature. The four | of the seven. For example, the first combinations of switches are switch setting is “A”, Therefore the labeled A,B, C, and D and are | following Is displayed displayed on the screen. ROMOK A
FOOTBALL 1-9
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAME PLAY
A. INTRODUCTION The Atari Football game has three different modes of operation. These modes are listed below: ATTRACT—when power is applied or as a result of a game ending with no further credits. READY-TO-PLAY —coins accepted PLAY — initiated one second after pressing the Play-Select button.
B. PLAYER CONTROL PANEL (See Figure 2-1) The Atari Football game consists of two player control panels (a control panel is illustrated in Figure 2-1). These two control panels are operated simultaneously by opponents. Each control panel is capable of operating either the offense or the defense, depending on game conditions. The player control panel consists of a trackball, a Play Select board and a dual function LED pushbutton (its primary function is as a Play Select switch and secondary function as a Press-to-Pass switch). When the Play Select switch is active, the LED flashes. When the play has been selected, and after one second, the Play Select LED will go off, changing the switch function to a Press-to-Pass.
The Play Select Board (See Figure 2-2)
The Play Select display board illustrates four offensive and four defensive plays, two of which are running plays and two passing plays. The upper, which is the offensive set of plays, is back-lighted by three incandescent lamps. The defensive, at the lower portion of the display board, is also back-lighted by three incandescent lamps. Prior to selecting any of the four plays, whether offensive or defensive, the four LED lamps are dark. Pressing the Play Select pushbutton switch lights a random LED. The player may now make his selection by stepping the LED from play to play (left to right) at any time he wishes, prior to the time required for scrimmage by continuing to press the Play Select switch. On the next play, the LEDs start dark until the Play Select pushbutton switch is pressed once more.
The next item of importance at the player control panel is the trackball. The trackball is the actual manual control for either the pass receiver or the quarterback if you're the offensive player, or the safety if you're the defensive player. This trackball control is operated by rolling it in any direction, 360 degrees, with the palm of the hand. It positions the offensive man with the ball or defensive safety at any position in the scrolling playfield by moving him at a rate proportional to the roll of the ball. The only time the trackball is active is during the Play mode and the only time that the Play Select pushbutton switch is active, is during the Ready-to-Play and the Play mode. During any other mode other than the aforementioned, these coritrols are totally inactive. Therefore, everything remains inoperative until credits are provided.
2-2. FOOTBALL Cc. ATTRACT MODE (See Figure 2-3) The Attract mode begins when AC power is applied to the game and the power on/off switch is turned to “on’ (The power on/off switch is located on the underside of the game cabinet’s table top, as illustrated in Figure 1-4.) While in the Attract mode, the TV monitor displays random play. For example, it randomly selects a play such as the Sweep running play. This selection is indicated by the LED at the Play Select display board when the red LED lights in at the Sweep play. Then, regardless of whether the player is offense or defense, the play continues and is played out until the man is tackled, goes out of bounds, makes a touchdown, or his pass is intercepted by a defensive player. He returns to a huddle. Then while in the Attract mode the screen displays the next play (the Keeper, the Bomb, and so on). Regardless of the control panel, the Xs indicate the defensive players and the Os indicate the offensive players. A better understanding and explanation of the players and plays will be discussed in the following paragraphs under the Play Mode section. D. READY-T (See Figure 2-4) -PLAY MODE
The Ready-to-Play mode is initiated immediately after the coins are accepted by the coin mechanism. After the coins are accepted, the Play Select pushbutton switch becomes active. The screen then changes from its current Attract mode display to the huddle (offense and defense). The game is in the player's hands, and the audio is now active.
Actually, this mode exists at each huddle regardless of the score or of offense or defense conditions. Whenever the game goes into a huddle, for both offense and defense, we are in the Ready-to-Play mode. In this mode, the coin message is no longer displayed in the scoreboard display field. Instead, the scoreboard indicates whether you are the offense or defense. The scoreboard indicates a zero score when first placed into the Ready-to-Play mode, and the down number and yards to go. Time begins to tick off, and the score, down, and yards-to-go change according to the game conditions. The game is now redy to be played. The Play Select pushbutton switch is activated and flashes.
The game circuitry accepts coins at any time. Each coin adds time selected by the operator to the game-timer (up to a maximum of 99 minutes and 59 seconds). If coins
PLAY SELECT BOARD DISPLAYS ILLUSTRATIONS OF PLAY (OFFENSE AND DEFENSE).
SWEEP KEEPER BOMB DOWN & OUT TRACKBALL CONTROLS USE PALM OF HAND TO MOVE PLAYERS 360° ROTATION
FLASHES WHEN ACTIVE AS PLAY SELECT FUNCTION
DARK WHEN ACTIVE AS PRESS TO PASS FUNCTION
Figure 2-1 Player Control Panel
OFFENSE LEDs Jf x i x
© keererR |© some x
© pown AND OUT
Figure 2-2 Play Select Board Display «OFFENSIVE « QUARTERBACK AND RECEIVER
° DEFENSIVE SAFETY
BACK ILLUMINATED BY INCANDESCENT LAMPS
FOOTBALL 2-3
LEDS CHOSEN RANDOMLY
TRACKBALL INACTIVE
DEMONSTRATED
ALTERNATELY FLASHES WITH COIN MESSAGES ~
- GAME OVER
DARK
LEDS CHOSEN RANDOMLY
Figure 2-3 Attract Mode
2-4 FOOTBALL
TRACKBALL INACTIVE
DEFENSE HUDDLE
INACTIVE
LED FLASHES UNTIL THE PLAY SELECT SWITCH IS PRESSED, THEN IT GOES LEDS ARE DARK UNTIL DARK THE PLAY SELECT SWITCH IS PRESSED. REPEATED PRESSING THEN THE PLAY LED OF SWITCH STEPS INDICATOR HOLDS ON LED PLAY INDICATOR SELECTION. FROM LEFT TO RIGHT
Figure 2-4 Ready-to-Play Mode
FOOTBALL 2-5
are added in the Attract mode, the scores are reset and the game enters Ready-to-Play mode as described above. If coins are added during a game, the timer is extended with no other effect. (The operator option can be set so that the deposit of each coin adds 11/2, 2, 21/2, or 3 minutes to game time.)
E. PLAY MODE After the Ready-to-Play mode is displayed as discussed in the previous subsection, the players, offensive or defensive, may select a game by pressing the Play Select pushbutton switch. Immediately after pressing the Play Seiect switch the players are set to the line of scrimmage.
Plays Four plays are available to either opponent. These plays are the following: @ Sweep @ Keeper @ Bomb @ = Down-and-Out The first two plays are running plays, the last two are passing plays.
Offensive Running Plays The Sweep Play (See: Figure 2-5) First, we'll discuss the running plays, beginning with the Sweep. The offense has seven players; a center (1), quarterback (2), wingback (3), and two guards (4, 5) to the left and right of the center. Outside of that there are two tackles to either side (6, 7). In this version of the video Atari Football, the center hikes the ball to the quarterback, the quarterback is controlled by the player. (The man with the ball is always controlled by the trackball control at the control panel.) After the center has hiked the ball to the quarterback, the quarterback should run to the left side of the field and the center then proceeds to rush toward the tackle. All tackles and guards rush the line, blocking the defense from the quarterback as he rushes beyond the wingback. The wingback covers the quarterback all the way down to the end zone. The Keeper Play (See Figure 2-6) The Keeper is an offensive play where the center hikes the ball to the quarterback; the wingback, at the wide end
2-6 FOOTBALL of the field, begins to run deep. Immediately after the quarterback receives the ball from the hike, he rushes between the tackle and the guard or between the guard and the center and then into the field. The remaining men proceed to block for him.
Offensive Passing Plays The Bomb Play (See Figure 2-7) The offensive Bomb play is a long-distance passing play. The bomb is received at all times by the wingback, who always runs his pattern to the left side of the playing field. When the center hikes the ball to the quarterback, the player must operate the trackball so that the quarterback immediately drops back into his pocket. At the same time, the offensive line guards him from the defensive line. After the ball is hiked, the end player on the right runs a fake “down and out” pattern, and the wingback goes out deep down the left side of the field. At the appropriate time, the player must press the “Press to Pass” button to pass the ball to his receiver. If the wing back is too deep the ball will not reach the receiver. There is also the chance that a defensive player is in the immediate vicinity of the receiver and that the ball will be intercepted or knocked down for an incomplete.
The Down and Out Play (See Figure 2-8) The Down and Out is a short-distance passing play. All offensive action in this play is identical to the Bomb except that when the ball is passed, it goes to the tight end who runs a quick down and out pattern to the right side of the field. This is a short-pass play, and if the player waits too long before passing the ball, it will result in an incomplete pass. Again, as in the Bomb play, if there is a defensive player in the immediate vicinity of the receiver, a pass attempt may result in an interception.
Defensive Running Plays The Sweep (See Figure 2-9) In the defensive Sweep play, we once again have seven players. These players are indicated by Xs. We have four Xs which are on the line: the two center Xs are guards (1, 2), and the other two outer Xs are tackles (3, 4). Inthe next row, you have two men on either end off of ihe line of scrimmage and these two men are your linebacks (5, 6). The last man in the back of your field is your safety (7).
In the defensive mode, if you are the defensive player, this safety is the only player who may be operated by the trackball.
TO GOAL LINE
LINE OF
DEFENSE
Ne BLOCKING
POINTS a TIGHTENDS GUARDS _— CENTER QUARTERBACK (RUNS WITH (HIKES BALL TO 2) BALL TOWARD GOAL LINE FOR A TOUCHDOWN
Figure 2-5 THE SWEEP An Offensive Running Play WINGBACK
TO GOAL LINE
TO GOAL LINE ALONG DECEPTIVE QUTSIDES OF FIELD WINGBACK RUNNING r MANUEVER ' ‘ BALL / /
NN / — BLOCKING POINTS
QUARTERBACK (RUNS WITH BALL WINGBACK CENTER THROUGH LINE, AND TOWARD (HIKES BALL TO 2) OUTSIDE OF FIELD).
Figure 2-6 THE KEEPER An Offensive Running Play
FOOTBALL 2-7
*” GOAL LINE
: BALL IS BEING PASSED
\ BALL
\ \ x TO OUTSIDE . OF FIELD
x
| SCRIMMAGE | * | Y, | x | CENTER |
| \ | \ | x | x | (HIKES BALL TO 2) |
- en eee 0-—-~-—= 4 TIGHTEND RUNS \ Or eA «~~ TOWARD OUTSIDE OF FIELD a 6, 4, 1 and 5 GUARD 2, WHILE 2 PASSES BALL TO 3 WiIN@BackK——— “SS QUARTERBACK (RUNS BACK THEN PASSES BALL TO 3)
Figure 2-7 THE BOMB An Offensive Passing Play
TO GOAL LINE TO GOAL LINE BALL IS WINGBACK BEING
| DECEPTIVE | BALL | PASSED | POINT OF |
RUN x » COMPLETION DOWN / (ALONG OUTSIDE FIELD \ OF FIELD)
LINE OF y
SCRIMMAGE / CENTER \ x x 0 x x (HIKES BALL —SA—)/—-— eee A-—-—— TO 2) /
- / }———-TIGHTEND ‘ / , >
| belli eedaril | 6, 4, 1 AND 5 | OX | (RUNS BACK, |
GUARD 2, WHILE WHILE 2 PASSES THEN PASSES BALL TO 7)
Figure 2-8 THE DOWN & OUT An Offensive Passing Play
2.8 FOOTBALL
In the Sweep defensive illustration, Figure 2-9, we see that both guards and the right tackle rush toward a single point on the line—toward the quarterback. The left tackle goes a short distance back, rushes right and then all the way back again. At this point, the left linebacker follows him through and the right linebacker goes around the wingback of the offensive team, trying to get around the offensive line of scrimmage. Meanwhile, the player has complete control of the safety. The Keeper Play (See Figure 2-10) The Keeper defensive play shows that the front line rushes the offensive line to the left. The left lineback rushes past the line, around it, and the right linebacker follows him up. Meanwhile, the safety remains behind, controlled by the player. The Bomb Play (See Figure 2-11) In the Bomb defense strategy, once again we have the line being rushed by the defensive line together with the left side linebacker. The right side linebacker drops back into his own secondary, and automatically follows the offensive wingback, and defends against any attempted pass to the wingback. The safety is again in the hands of the player. The Down and Out Play (See Figure 2-12) During the Down and Out strategy, the line rushes together with the wide side linebacker. The short side linebacker drops back into his secondary and defends against the pass to the offensive player running the down and out pattern. Once again, the safety is controlled by the player.
The Four Goal Deterrents
The four goal deterrents are the intercept, incomplete, tackle, and out-of-bounds. These conditions are displayed at the lower part of your scoreboard display field. The incomplete pass (see Figure 2-13) occurs in a passing situation, when the quarterback pauses too long to pass it to the receiver down the field. It may also occur if the ball passes near a defensive player as it comes “down” to the receiver. This condition resets the game into a huddle at the initial scrimmage line and stops the clock.
The out-of-bounds (see Figure 2-14) occurs when the offensive player, while running in the direction of the goal line, goes off, onto, and past either side boundary; this stops the play, and the clock. The tackle (see Figure 2-15) is the condition on the screen where the defensive player (X) physically touches the offensive player (O). Once again, at the point of being tackled, the player could gain or lose, depending on which side of the scrimmage line the player may have been tackled. Occasionally he may be tackled in his own end zone and the defense scores 2 points.
When the defense intercepts the ball, the defense then becomes the offense at the same yardage as the point of interception.
Time Penalty A player is penalized five yards for not selecting his next play within ten seconds before lining up at the line of scrimmage or before pressing the game select button. Therefore, it is important that you reach your decision prior to ten seconds after your opponent does.
The Touchdown (See Figure 2-17) An offensive player scores when he reaches his goal line and makes a touchdown; the offensive players score 6-points for a passing touchdown and 7-points for a running touchdown. This touchdown occurs when the offensive player (O) carries the ball and actually makes contact with the last yardage line at his end zone. This end zone is opposite to the offensive player. Therefore, the offensive player’s goal line is toward his opponent. The screen proceeds to scroll in either direction, providing a full view of the field as the offensive player executes his plays. The active players are kept at approximately center screen.
FOOTBALL 2-9
ARROW INDICATES DIRECTION OF ATTACK
LINEBACKER
2-10 FOOTBALL
@ © TACKLE
TACKLE © © ©, LINEBACKER snessoun th ARROW INDICATES DIRECTION OF ATTACK ca a 6 a 7 caer :
(THE ONLY DEFENSIVE PLAYER CONTROLLED BY THE TRACKBALL)
Figure 2-9 THE SWEEP A Defense
TACKLE
SAFETY (THE ONLY DEFENSIVE PLAYER CONTROLLED BY THE TRACKBALL)
Figure 2-10 THE KEEPER A Defense
ARROWS TACKLE
INDICATE a
DIRECTION
2\ 44° car OF ATTACK
———— unepacker cwensonen’ \
TACKLE GUARD SAFETY (THE ONLY DEFENSIVE PLAYER CONTROLLED BY THE TRACKBALL)
Figure 2-11 THE BOMB A Defense
TACKLE ARROWS
INDICATE DIRECTION ~~ ATTACK LIN EBACKER— tact a LINEBACKER *™— GUARD 7 SAFETY THE ONLY DEFENSIVE PLAYER CONTROLLED BY THE TRACKBALL
Figure 2-12 THE DOWN & OUT A Defense
FOOTBALL 2-11
OFFENSE SELECTOR DOWN AND OUT
TRACKBALL INACTIVE
QUARTERBACK
‘
am Ox RECEIVER
INCOMPLETE
TRACKBALL INACTIVE
ASSUMED: DEFENSE SELECTED BOMB
Figure 2-13 Incomplete
2-12, FOOTBALL
TRACKBALL INACTIVE
RECEIVER OUT OF BOUNDS (TOUCHING SIDE BOUNDARY LINE) OFFENSE SELECTED BOMB
DOWN MARKER
DOWN TOGO oh tes akg bi g 010 ‘OUT OF BOUNDS
TRACKBALL INACTIVE
ASSUMED: DEFENSE SELECTED BOMB
Figure 2-14 Out of Bounds
FOOTBALL 2-13
ASSUMED: DEFENSE SELECTED BOMB
TRACKBALL ———-——-_—_> INACTIVE
2-14 FOOTBALL FF
ae Os Ovi a - ’ _-3u09s Shi oD6i Nmoo
RECEIVER TACKLED BY DEFENSIVE PLAYER
- TOGO.
- OY TACKLED
TRACKBALL INACTIVE
SELECTED BOMB
Figure 2-15 Tackled Offense
TRACKBALL ACTIVE
OFFENSIVE RECEIVER
QUARTERBACK ASSUME: DEFENSIVE SELECTED BOMB
ASN35IG BUY NOA. QO auods Sau
TRACKBALL ACTIVE
OFFENSE SELECTED BOMB
Figure 2-16 The Intercept
FOOTBALL 2-15
The Downs
In Atari Football, the offensive player is set up to control four consecutive offensive plays (described as downs). If in executing those four downs, the offense is able to gain 10 or more yards he automatically receives a “first down”, giving him another 4 consecutive offensive plays. If a first down is not obtained in 4 plays, the defense will get the ball.
On the screen there are two small quarter-inch markers on the outside of either sideline (see Figure 2-18), ten yards deep into the defensive field from scrimmage. These two markers represent the point ten yards downfield from the line of scrimmage which the offensive team must pass to gain another first down
The number of downs to go for the ten-yard marker is displayed in the left-hand corner of either player's scoreboard. For example, the first and ten (1 and 10)
2-16 FOOTBALL means that it is the first down and ten yards to go for another first down. On the fourth down, assuming that the line of scrimmage is two yards from the first down marker, the scoreboard would read down 4 and two yards to go (4 and 2). If the quarterback had received the ball and been tackled twenty-five yards from the first down marker, on the third down play, it would be displayed as 4 and 25 on the scoreboard at the end of the play.
Defensive strategy here is to make sure that the offense doesn’t get his first down and ten, giving him more chances to score.
TRACKBALL INACTIVE
TOUCHDOWN PLAYER TOUCHES GOAL LINE
DOWN TOGO TIME 4
2 ey S O10 ee TOUCH DOWN DEFENSE SELECTED BOMB
o oe ney .4 ee “auoSs aul” cp di nwo
GOAL LINE
TRACKBALL INACTIVE
ASSUMED: DEFENSE SELECTED BOMB
Figure 2-17 Touchdown
FOOTBALL 2-17
2-18 FOOTBALL ‘ sanesne LOGE auoSs Sait 00 61 Nod
be
iE ‘3 oo - GO Bors Sf0R YOU ARE OFFENSE
Figure 2-18 Down Location “FIRST DOWN” MARKERS
PLAYERS AT THE LINE OF SCRIMMAGE
THEORY OF OPERATION
A. GENERAL INFORMATION This chapter provides a general overview of the theory of operation of the Football electronics contained on the game printed circuit board (PCB). It also goes into specific detail of the various circuits to explain to an individual of moderate technical background how these circuits should perform. This detailed information has been organized with emphasis placed on troubleshooting the game PCB, circuit by circuit.
The Football game block diagram of Figure 3-1 illustrates the major components, including all controls remote to the game PCB. The function and direction of the information to and from these various controls is also shown.
The Football PCB block diagram in Figure 3-2 illustrates the division and function of the various circuits located on the game PCB and how they are controlled by the microprocessor. Refer to Figure 3-2 as you go through the following circuit descriptions.
FOOTBALL
TV MONITOR
HORIZONTAL DEFLECTION \
bababilea MONITOR INTENSITY,
tI) INTERLOCK. i ouett an ‘SWITCH rT
TRACK BALL ‘CONTROL, PLAYER-ONE
aie een CONTROL PANELS: oan, \ en) p—-——— a
SPEAKER
PASSIPLAY
coin MECHANISM
TEST fe J |RACKET LOCATED BEHIND THE COIN DOOR (REFER TO FIGURE 1-6)
Figure 3-1 Football Game Block Diagram
3-2. FOOTBALL
Figure 3-2 Football PCB Block Diagram
FOOTBALL 3-3
The functional operation of the Football PCB circuitry begins naturally enough with the microprocessor (or MPU) circuitry. As you go through the various circuit descriptions, you learn how the MPU receives its sequential program instructions from its ROM memory and how it carries out these instructions through the use of its display RAM memory (Section C); how it reads in the game control switches (Section G), and how it writes or outputs the results of its instructions and calculations to the game’s other PCB circuitry, such as the playfield generator (Section E), the motion object generator (Section F), and the audio amplifier (Section K).
A circuit description of the standard Atari sync generator (Section D) is also included. This is the only PCB circuitry that functions independently of microprocessor control.
All reference schematic diagrams of the aforementioned circuits are found in Appendix A at the end of this manual.
B. POWER SUPPLY (See Figure 3-3) The power supply produces all the necessary game voltage requirements as shown in Figure 3-4.
The PCB receives + 10 volts DC, unregulated, at pins B and 2 of the game PCB edge connector and 25 VAC to pins W, 19, X, and 20 from the secondary of the transformer located on the Type B power supply chassis.
The +10 volts is rectified and filtered off-board and regulated on-board by the LM323_ three-terminal regulator device to a stable +5 volts DC. The +5 volts DC is distributed throughout the PCB to power all logic circuits. The 25 VAC input is rectified through diodes CR1 and CR2 filtered by capacitor C62 and supplied as unregulated +18 volts to the TDA 1004 audio amplifier. This +18 volts is also regulated by a three-terminal device 7812 to develop +12 volts DC.
Cc. MICROPROCESSOR CIRCUITRY The heart of the Football game PCB is the microprocessor circuitry. A brief description of the major components and their function within the microprocessor circuitry is provided in the following paragraphs. Note that
3-4 FOOTBALL the microprocessor circuitry components include the following: (See Figure 3-5)
. MPU (at location C2) . Gated address buffers (B1 and C1) . Data buffers (E2) . ROM memory (P1, N1 and M1) for -02 version or PROM memory as listed in the PCB assembly parts list for the -01 version (refer to Illustrated Parts Catalog, Chapter 5).
- RAM memory (M2, N2 for working RAM)
- Address decoding circuitry (B3, E3, C7 and miscellaneous gates) Pwnrwe
- Watchdog reset counter (A4 and miscellaneous gates)
MPU, ROM, and RAM (See Figure 3-6) The microprocessor is the “master controller” behind all action that takes place in the game circuitry. In going through the following paragraphs refer to Table 3-1, MPU Input/Output Signal Descriptions. Upon initialization, the MPU (via ABS 0 - BUS 15) addresses data permanently stored in the program ROMs or PROMs. This addressed data then travels to the MPU via its 8-bit data bus (DO through D7). The MPU decodes this data to determine what action it is to perform next (i.e., “read coin switch 1,” “bomb play” etc.). The MPU uses RAM memory to perform many of these instructions, namely to temporarily store information which it wil! later recall. The MPU is capable of writing (or putting data into) the RAM and then later reading (pulling data out of) the RAM, via its address bus (ABUS 0-ABUS 15) and bidirectional data bus (DO-D7).
Address Decoding (See Figure 3-7) The MPU address decoding circuitry performs the critical function of turning on or enabling the appropriate game circuitry (i.e., RAM, ROM, latches, etc.) at the appropriate time, so that information can be transferred back and forth between this game circuitry and the MPU. A memory map defining the address decoding circuit is shown in Table 3-2 as reference.
16.5VAC CT
25VAC | w [19] +12V 1N4001 cas asvac Ta cR2 1” I (BYPASS) +18V = =
L 4,700
asvacer [y [21] GND | z | . Refer to the Schematic
diagrams in Appendix A for appropriate designation of pin numbers.
R1, 2, 6,9, 11, 12, | K | +5V (PULLUP)
+ 10V (UNREG) +5V
C1-11, 14-18, 20-22, 24-26, 29-31, 36, 37, 42, 46 L -1(BY PASS) Irs 1} KA
Figure 3-3 On-Board Power Supply Schematic Diagram
FOOTBALL 3-5
+10 VDC (UNREGULATED)
AC SOURCE ~
25VAC ~ GAME PCB POWER SUPPLY REGULATOR CIRCUITS TO AUDIO AMP (UNREGULATED) + 12 VDC.
Figure 3-4 Power Supply Simplified Block Diagram
o 0 Clock Driver The basic operating frequency of the microprocessor is established by its 0 input (on pin 37 of the MPU device). The Football MPU runs at an operating frequency of 750 KHz. Examination of the MPU 2 output waveform (pin 39) with an oscilloscope should show a signal with a period of 1.33 microseconds. (The period of any periodic waveform is the measurement of the time it takes to complete one full cycle.) The 750 KHz clock outputs are generated by the 4H signal. This 4H frequency is generated by the horizontal sync counter P5 to produce the 0 clock input. See Figure 3-8, © 0 Clock Driver Signal.
Watchdog RESET (See Figure 3-5) The reset counter in the microprocessor control circuitry consists of a 4-bit decade counter, A4. The Q, output of this counter is the RESET signal to the MPU. Counter A4 counts how many times the 128V signal changes states. On every high-to-low transition of 128V, the counter advances to the next count in its sequence. Meanwhile, the WATCHDOG signal, generated by the MPU at various times during its normal instruction sequence, is resetting the counter back to zero. If for some reason the MPU program has strayed from its intended instruction sequence and the WATCHDOG signal does not occur before this counter counts up to a point where
3-6 FOOTBALL the Q, output goes high, a RESET signal is generated to the MPU. The RESET signal causes the MPU to restart its instruction sequence from the beginning of the program.
D. SYNC GENERATOR (See Figure 3-9) The base frequency of the sync generator is a 12.096-MHz clock, generated by a crystal-controlled oscillator consisting of crystal Y1, inverter N4 and several discrete components. The output of this oscillator is 12 MHz. Examination of this signal with an oscilloscope (at pin 2 9f N4) should show the period (or cycle time) to be approximately 83 nanoseconds (.083 microseconds). See Figure 3-9.
This base frequency is then divided down by binary counters P5, P6, N6: it provides the various horizontal synchronization frequencies (1H through 256H). The final output of this horizontal counter chain is 256H (at pin 13 of N6). This signal is in effect a division of the base frequency (12.096 MHz) by 768, to give a horizontal line frequency of 15,750 Hz. The period of 256H is about 63.5 microseconds. The 256H signal, as well as other horizontal signals, are used to generate the H BLANK and H SYNC timing pulses at flip-flop N5. See Figure 3-11, Horizontal Sync Timing Diagram for the relative timing of these waveforms.
Table 3-1 MPU Input/Output Signal Descriptions
| Signal | Description /Function | Signal | Description/Function |
| p0-D7 | These eight lines are bi-directional data | RESET | When low, this input line resets the |
bus lines. MPU on either a “power-up condition” AO-A15 | These sixteen lines are unidirectional or aQy output of the watchdog MPU address lines to supporting counter. During the reset sequence memory (i.e, ROMs, RAMs) and I/O. prior to RESET going high, the con-
| RO | Th | t, | when | | | indent | tents of two locations (FFFC, FFFD) in |
is input, when low, indicates an memory are loaded into the MPU pro-
| interrupt to the MPU. After the MPU | fer | ti | int the | start of |
concludes its current instruction it will acct routine. © Point ihe start of @
proceed to the IRQ sequence.
| R/W | This output is the read and write signal | 00 | Clock input |
line, which indicates the direction of 1,02 | Two-phase, non-overlapping MPU data transfers on MPU data bus. clock outputs.
Table 3-2 Atari Programmed Memory Map
| 6800-7F FF | PROGRAM | — | |
| [S000 | : | WATCHDOG _ | - |
40004008, INPUT PORTS
| 3000 | INTERRUPT ACKNOWLEDGE | Z |
20002003 ‘OUTPUT PORTS 1000-198F ‘SCROLUFIELD 13C0-13FF MOTION OBJECT PARAMETERS - 03A003FF "| PLAYFIELD— PLAYER 2 200.025 PLAYFIELD—PLAYER 1 0000-01F F WORKING RAM _
| wPurioureurponts | or | | os | | os | | oe | os | | | v2] | [bo |
2000 (00% 9 ‘SCROLLFIELD OFFSET (@ BITS)
| 2001 (OUT) | SPARE | kicker | HIT | WHISTLE |
con
| 2002(0UT 2) | arrract | GON | NOISE AMPLITUDE | ||
| 2003(0UT 3) | SPARE | LED CATHODE BITS) | ||
| 4000 (INO) = 0 | COINT | END. | SLAM | SELECT1 | TRACKBALL-DIRECTION |
| o“ | ‘SCREEN | T'prinD_ [PLivD | PL2HD| PLavD | ||
| 4000 (CTRLD} = 1 | TRACK-BALI VERT. 1 | TRACK-BALL HORIZ. 1 |
amozewa = 0 cons | reer | stave [seucore] ———OPnONSW
| 4002 CTRL | TRACK BALL VERT.2 | TRACKBALL WORIZ.2 |
E MOTION OBJECT PARAMETERS 1300 MOTION OBJECT 1 PICTURE # 1301 MOTION OBJECT 1 VERTICAL POSITION
13€0 MOTION OBJECT 1 HORIZONTAL POSITION 7 1303 MOTION OBJECT 2 VERTICAL POSITION
Et ‘SPARE 1902 MOTION OBJECT 2 PICTURE #
1382 (MOTION OBJECT 2 HORIZONTAL POSITION
1383, SPARE
190E MOWON OBJECT 1 PICTURE # 100F MOTION OBJECT 16 VERTICAL POSITION 19FE MOTION OBJECT 16 HORIZONTAL POSITION rad ‘SPARE
FOOTBALL 3-7
SOGooe +8v
Refer to the Schematic diagrams in Appendix A a for appropriate designation in numbers. anis [25 asusis ofp s © asia} 24 abusia © pia} 22 ABUSIS Pare Q I api2}22 ABUST2
poy rc © aBUStH PARE apustt ; 8 fa0) +5 B10 (5 ABuStO aBusIO av Sto ago | _T ©) ABuso Pre aBuso a
- ase. asuse ean ABUSE « ce av = Pest 90-6010 WATCHDOG [g AIBET wu Bern DISABLE cw _® Taeaa warcko08 1 Br aaus7 seu aaus7 2 1 " iO) roy S03 ABS a ABUSS 18H ABUSE a i 485 b Buss au BUSS ea £ © [> asus; 128 BUSA als ely +=” ay aq [POP RODRET HER], AB3 Buss say ABUSS trav dn ae 50 f=) a ‘ey Ste torn [0 aB2 abuse v apusz es Guncap as + © aBust 16y aBust rate Te 7 =O) Bo B ABUSO aw ABUSO VY +8v ns +8 “ Fo Pt yo 2 = Ba ur Boz reser — Res ee (a a7 B opus ENDSCREEN — G3) 0s © Bs B peuss Pre re os es - B Buss ote 4 Gs) -— ba
- iy Ro pan 2], ? of? 28 DBs B aus we 28) os wi tcn” ale— can Bs D Buss c rr Cc 77 Be B pBus2 __ oy iNTACK pe [= D ppust oo = Bo f © J euso
+8v 1 sync repr O9
oS aH *0 3) nos 02 SS08 4 b02 ‘a B03: 4 30) RW oy
OOOOOO ware
Figure 3-5 Microprocessor Schematic Diagram
FOOTBALL
FROM PROGRAM EITERION MEMORY
ic yompu “21 VERSION, cnipce
(ROM cms) BATE] ‘sa version’
AyPROGRAM MEMORY “4
FROM PLAYFIELD (omer
‘gaapnies TO VIDEO, PROW GENEATOR MEMORY ceracurTa (roms 5,05)
B)GRAMICS MEMORY
‘SrwnOe (SCROLLFIELO WRITE,
PLAYFIELO ADDRESS alts (SYNCIADDRESS) PAB: YNCIADDRESS) PFA: fam f (eches) | DATAOUT—_) PFD 0-3, 8-11, 16-19, 24-27 teas Ha, Ka)
PFO 4.7, 1245, 20-2, 28-31
‘SF waga(SCROLLFIELD WRITE)
C/PROCESGOR, SCROLLFIELD, MOTION OBJECT (GEADIWRITE) MEMORY
apa rr woRKING FROM HPL ‘ear 2 sx LINE Ly rans. neceven
Toman FAWBT ‘OMEAIGS PROM. [PEWR (PLAYEIELO WRITE)
DD) WORKING AND ALPHANUMERICS
| READTWRITENMEMROY
ave RUMERICS, PROM (Nr) AND, REFAY REF RELATED eiRcUITRY
WREroNTT
ALPHABLANK, [S ALPHANUMERICS PROM MEMORY
Figure 3-6 Memory Block Diagram
FOOTBALL 3-9
Figure 3-7 Address Decoding
750KHz
4H ia (1 CYCLE) ,|
PS PIN 41
0 (4H) €3 PIN 37
Bo2 D3 PIN4
Figure 3-8 0 Clock Driver Signal
The H SYNC signal is used to clock two stages of vertical sync counters M5 and M6. This H SYNC signal is divided down by these counters to form the various vertical synchronization frequencies (1V through 128V). These two stages of vertical counters are used, in effect, to doa divide by 262 of the H SYNC signal. This results in the final output of these counters (128V at pin 11 of M6) to be a signal at a frequency of 60 Hz (the period is
3-10 FOOTBALL approximately 16.6 milliseconds). The various vertical frequencies address a sync PROM (L5) whose output data is latched by latch L6. The outputs of this latch are the various polarities and phases of the vertical timing frequency used to synchronize the TV monitor display. These signals all run at a frequency of 60 Hz. See Figure 3-12, Vertical Sync Timing Diagram, for the relative timing of these waveforms.
Pater to the Schématic
BIN CNTR ‘Q0 oF
02 03_wP.
Figure 3-9 Sync Generator Schematic Diagram
FOOTBALL 3-11
CRYSTAL: 12.096 MHz (¥1) CRYSTAL:
OSCILLATOR
(Na)
HORIZONTAL SYNC PULSES haiti HORIZONTAL
sync
COUNTER
(P5,P6,N6)
VERTICAL SYNC.
‘CONTROL
SIGNAL cincurr (NS)
ENDSCREEN
Figure 3-10 Simplified Diagram of Crystal-Controlled Oscillator and TV Sync Circuitry
3-12. FOOTBALL
re a ee ee es ee 128H ~<—_—_——_4— 63.5 MILLISECONDS ———_____—_»| 256H PLAYFIELD DISPLAY yecank ——MMA ysync ———BME
Figure 3-11 Horizontal Sync Timing Diagram
vw JU UU LLL Le.
| w | i _f!US | LS | Ur | Ur | Ls | US | Ure |
| wi | St | io | fF | Li | fF | les | L |
| ev | — | ”O—<“ | L$] |
128V 16.3 MILLISECONDS ——_——-=>
VBLANK << PLAYFIELD DISPLAY, ce | SYNG ———————_____—____ PF v VRESET ———____
Figure 3-12 Vertical Sync Timing Diagram
The end result of the horizontal and vertical timing E. ALPHANUMERIC waveforms is to synchronize the TV monitor display. This GENERATOR display consists of 262 horizontal lines per frame, with each line being the time equivalent of 768 12 MHz clock (See Figure 3-13 and 3-14) pulses. Each frame is repeated 60 times per second, pro- Alpha and numeric characters are displayed as 8 line viding the necessary frequency of display refresh that by 8 bit blocks of video at the scoreboard display area of provides a stable non-flickering display. the TV monitor screen. These alphanumeric characters
FOOTBALL 3-13
are stored in PROM N7 (See Figure 3-14) which is accessed by addressing the data from the RAM (M2, N2). The microprocessor loads the alphanumeric location bits into the RAM. The RAM outputs (RAM 0-7) are then temporarily latched by latch M7 at the rising edge of the 4H clock. The latch output bits then address the alphanumerics PROM N7 (at address inputs A4-A9) and address one of the 64 different pictures stored in it. The vertical reflect signals (REFL4V, REFL2V, REFL1V) and the horizontal reflect control signal (HREFLCNTL) and sync signal 4H determine which of the 8 lines of the character is currently being addressed.
The reflect signals determine the alphanumeric image rotation which is displayed at either end of the TV monitor screen facing the player.
The 4-bit parallel output of alphanumeric PROM N7 is then converted into serial data by shift register P8 and summed into the video output circuitry. Shift register P8 is gated by NAND gate NQ, which is controlled by the ALPHABLANK window signal.
F. SCROLLFIELD GENERATOR (See Figure 3-15 and 3-16) The scrollfield generator generates the scrolling playfield video. The video is actually generated by the data stored in the graphics PROM comprised of PROM devices C5 and D5. See Figure 3-15. This PROM video information is addressed by data from the playfield display RAM. The method by which the MPU writes the appropriate scrolifield data to each RAM location and then the horizontal and vertical timing signals read this data out for actual video generation is known as “cycle sharing”. The
64,8 BIT x 8 LINE ALPHA AND NUMERIC yo CHARACTERS
VERTHORIZ
PLAYFIELD REFLECT WRITE ans circuitry that controls this “cycle sharing” technique selects one of 3 sets of addressing information to address the display RAM,
This circuitry functions as follows:
- When buffered MPU clock B02 is high, the MPU address bus (AO-A15) addresses various playfield display RAM locations, and writes appropriate scrollfield picture codes into them via the MPU data bus (DO-D7).
- When BO2 is low and 256H is low, horizontal syne signals (8H, 16H, 32H, 64H) are enabled to address the RAM. This is used for motion object display.
- When B02 is low and 256H is high the vertical syne signals (16V, 32V, 64V, 128V), the shifted horizontal sync signals (SFH4, SFH5, SFH6, SFH7) address the playfield. These shifter signals are the result of adding the top 5 bits of the scroll latch, F7, to the horizontal sync functions. They provide a “coarse”, 8 bits at a time, horizontal shift of the scrollfield.
Since the data was read out of the RAM by the horizontal and vertical sync signals, the picture codes PIC 0-7 always correspond to the portion of the monitor display currently being scanned. Because of this, the PIC 0-7 outputs can be used to generate video information for immediate display. These PIC signals address one of 64 8 x 8 pictures stored in graphics PROMs C5 (LSB), D5 (MSB). The output of the PROMs is then converted to serial video information by shift register A6.
The serial video is then displayed 0 to 7 bit times by variable delay circuit shift register J8 and multiplexer H8. This circuit provides the “fine” horizontal shift of the scrollfield.
Refer to the Schematic diagrams in Appendix A for appropriate designation of pin numbers.
apis _ TO SCROLLFIELD
VARIABLE DELAY
SERIAL ‘SERIAL CincUITAY
‘CONVERTER, PARALLEL. To
Figure 3-13 Alphanumerics Generator Block Diagram
3-14 FOOTBALL
not Aran ast
ast
Figure 3-14 Alphanumerics Generator Simplified Schematic Diagram
FOOTBALL 3-15
areas aa
EQUWALENT BLOCK O14GRAM, I diagrams In Appendix A for appropriate designation of pin numbers. Refer to the Schematic
Figure 3-15 Scrollfield Generator Block Diagram and Simplified Schematic Diagram
3-16 FOOTBALL
FOOTBALL 3-17 Refer to the Schematic diagrams in Appendix A for appropriate designation of pin numbers. ee gsaales ae
Figure 3-16 Display RAM Simplified Schematic Diagram
G. MOTION OBJECT GENERATOR (See Figure 3-17)
The motion object generator preduces characters such as the football and the Xs and Os. These motion objects are generated by the same circuitry found in the scrollfield generator (see Figure 3-15), while the actual graphics are permanently stored in PROMs C5 and D5 (see Figure 3-17). This circuitry is used for motion objects when 256H is low, and for scrollfield when 256H is high. The RAWVID signal from the parallel to serial shift register A6 is connected to OR gate K3. This gate ORs the raw video (RAWVID) from the scrollfield circuitry and the data out (DO) from the RAM K6 which __ was cleared while the information on that line was being read out. The procedure is as follows for each motion object:
- The horizontal position is latched at J5. It is used to set counters K5 and J6 to the desired start position.
- The vertical line number is effectively subtracted from the vertical position by adders F5. The H5 produces a match signal if the object is visible on this scan line. It also produces the LINE 0, LINE J and LINE 2 signals which select one of eight scan lines with an object.
- The LINExx signals, together with the picture code, PIC 0-5, are used by the graphics circuitry to produce the RAMVID as previously discussed.
MULTPLExED
venrical SYNC comPaRaTor mK pcr count othe REFLECT ID waren
- The 8-bits of RAMVID are ORed with any existing data in RAM (K6) from previous objects and placed in the RAM at the address latched in J5, and the next seven serial addresses.
These steps are repeated for each of the 16 motion objects during the time 256H is low. The HCLR signal then resets the K5 and J6 counters. The data is read out of the RAM as MVID while 256H is high. The location is read and its contents are sent to the video circuit. The RAM is cleared by output of AND gate L8 prior to the next data line.
H. TRACKBALL CONTROL AND SWITCH INPUT CIRCUITRY
(See Figure 3-18)
The trackball control and switch input signals are multiplexed as illustrated in Figure 3-19. This multiplexing is accomplished by alternately selecting the mode of operation for ihe pre-settable counters D9, D10, H10, and H9. When the counter load signal (CTRLD) goes low, it reads the switch status by loading a preset count into the counter inputs (A, B, C, D) and then latching and outputting the data into schmidt device E10. When CTRLD goes high the trackball control signal toggles the counter either in a count up or a count down direction. The counter outputs then are gated via E10. Both trackball and switch signals are then sent to the microprocessor via the data bus (DO - D7).
Refer to the Schematic diagrams in Appendix A for appropriate designation of pin numbers.
anapnics ‘cRCUITRY ‘stock (REFER TO Excsive TNEOR ee FIguRE #15)
ucripLexeo (MOTION oBsEcT p> WoEO To vide ‘SUMMING CIRCUIT
Figure 3-17 Motion Object Generator Block Diagram
3-18 FOOTBALL
Seat
tomes Dara ous
Refer to the Schematic diagrams in Appendix A for appropriate designation of pin numbers.
Figure 3-18 Trackball Control and Switch Input Simplified Schematic Diagram FOOTBALL = 3-19
J. VIDEO OUTPUT (See Figure 3-19) The video output circuit receives all the video signals (MVID, RAWVID, SCROLLGATE, SCRFVID, ALPHA, and related sync signals) and gates these signals logically summed at the Q1 emitter follower device (2N3643). The signal at the emitter of the transistor then becomes the composite video signal sent to the games TV display monitor. K. AUDIO GENERATOR AND AMPLIFIER (See Figure 3-20) The audio generator produces the crowd whistle and ball sounds. The crowd sound is the result of the gated random noise generator composed of shift registers A8
3-20 FOOTBALL and B8. The NOISE output of this generator is gated “on” each time the KICKER signal goes low. The KICKER signal is developed by the microprocessor via LATCH F8. The crowd sound volume is automatically controlled by the data bus bits DBUS 0-5. The noise (unfiltered crowd sound) is then filtered by the active bandpass filter circuit comprised of one-half of Op-Amp A9 (LM324). The other half of AQ is the audio mixer which sums the hit, whistle and the crowd sounds. The whistle sound is generated by VCO control bit 1Q of F8 which gates the VCO “on”, therefore producing the whistle sound.
The output of the audio mixer A9 is then amplified by the TDA-1004 audio amplifier device. Potentiometer R75 controls the level of audio output.
nian |
FROM SCROLLFIELD
GENERATOR VIDEO
SUMMING
CIRCUIT
FROM
ALPHANUMERICS = GENERATOR ——-———> ALPH
EMITTER
FOLLOWER
VIDEO OUT SCROLLGATE
4.5K Lo-------___ Figure 3-19 Video Circuit Simplified Schematic Diagram FOOTBALL 3-21
3-22 FROM MPU DATA BUS.
From MPU DATA BUS,
58H RANDOM NOISE GENERATOR
a L5164 SHIRES BSRSsee COIN eNTR eT 1 vouTaGE +0 CONTROLLED | oscntator Lf if
! ' i
i
wHisTie | fos Bre
mK R70 ey aK
ars
lactive {BanoPass [Aupio Fitter at eee ones eee been!
AUDIO MIXER r
voLUME] --- eo 5
Le ee Se AUDIO AMPLIFIER Leet ee
Refer to the Schematic diagrams in Appendix A tor appropriate designation of pin numbers.
Figure 3-20 Audio Generator and Amplifier Simplified Schematic Diagram === ------~---5 Lois ——
MAINTENANCE AND ADJUSTMENTS
Due to its solid-state electronic circuitry, this Atari unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical background.
A. CLEANING
The exteriors of game cabinets and Plexiglas® panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the acrylic plastic panels, because any dust can scratch the surface and result in fogging the plastic.
B. COIN MECHANISM Components On Coin Door Figure 4-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. Powering the game causes the lock-out wires to retract far enough to allow genuine coins to reach the coin box. When AC power to the game has already been turned off, the lock-out coil is de-energized, causing the lock-out wires to move out far enough to divert coins to the return chute.
Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending
LOCK-OUT COIL LAMP HOLDER
Figure 4-1 Coin Door Assembly
4.2 FOOTBALL out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wite down and cause the switch contacts to close.
Also shown in the photograph is a slam switch assembly. It has been included to defeat any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.
Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 4-2. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pushing down on a release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 4-3.
Plexiglas® is a registered trademark of Rohm & Haas Company.
Figure 4-2 Hinging Open the Magnet Gate Assembly
Figure 4-3 Removal of Coin Mechanism
Cleaning of Coin Paths
By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.
Figure 4-4 shows the surfaces to clean inside the coin mechanism. These include the inside surface of the
(CLEAN BOTH SURFACES WHERE COIN ENTERS THE MECHANISM, AS WELL AS THE MAGNET)
Figure 4-4 Surfaces to Clean Inside the Coin Mechanism mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.
If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a 3/8-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 4-5). Removing the plate will provide access to the entire channel.
Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.
Figure 4-5 Removal of Plate Covering Rear of Coin Slot
Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 4-6 shows this lubrication point.
Adjustment of Coin Switeh Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 4-7. Use extreme care when handling or touching these wires.
FOOTBALL 4-3
MANUALLY HOLD DOWN REJECTION BUTTON AND APPLY ONE DROP HERE
LOCK- OUT WIRE
Figure 4-6 Close-Up View of Lubrication Point
In Figure 4-7 you will note that the coin switch trip wire is oriented into the “V” of the secondary coin chute. The wire should extend to only about 1/8” beyond the chute.
A retaining clip holds the wire onto the switch actuating stud. If you should lose a retaining clip, all is not lost. dust crimp the switch actuating stud over the trip wire with a pair of pliers.
Mechanical Adjustments on Coin Mechanism Coin mechanims are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it toa clean well-lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure 4-8 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by someone who has experience in servicing coin mechanisms and who understands their operation.
4-4 FOOTBALL CORRECTLY ADJUSTED TRIP WIRE
Figure 4-7 Detail View of Coin Switch and Trip Wire
General Troubleshooting Hints
The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.
Kicker and separator 2
- Set the acceptor with the back of the unit facing you in the test position.
as far to the right as they will go. Lightly tighten the screws.
- Insert several test coms (both old and new) and note that some are returned by the separator.
- Loosen the separator screw and move the separator a slight amount to the left. tetighten the screw.
coins are accepted.
the screw.
- insert the test coins and note that some are returned.
the screw.
are accepted.
- Be sure that both screws are tight after the adjustments have been made.
Magnet gate . Set the acceptor with the front of the unit facing you in the test position. no will fit through.
coin barely passes through the magnet gate.
through the magnet gate, repeat Step 3 until all the coins are accepted. Fix the magnet gate adjusting screw in this position with a drop of glue.
Additional Cleaning
- Remove the transfer cradle (12) and the undersize lever (14).
- Replace the transfer cradle and the undersize lever.
reinstalling in the door. ITEM IDENTIFICATIONS Kicker and Separator Screws Washers Kicker Separator Gate Lever Spring Gate Pivot Pin Mainplate Assembly washer Rail Gate Assembly Cradle Assembly
Upper Gate Pivot Spring Undersize Lever Assembly Magnet Gate Assembly Magnet Gate Adjuster Retaining Screws Coverplate Assembly Return Coverplate Coverplate Mounting Studs Lower Gate Pivot Spring Coin Release Lever
- Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4)
striking
Lightly
- Insert the test coins again and, if some are still returned, repeat Step 4 until all the
- Loosen the kicker screw and move the kicker as far to the left as ii will go. Lightly retighten
- Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten
- Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins
. Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins
With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the
. Test this adjustment using several other coins (both old and new) and, if any fail to pass
- Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
- To be certain the coin mechanism is completely free of any residue, place the mechanism in boiling water for several minutes. Carefully remove it and let it air-dry completely before
Figure 4-8 Adjustments on Coin Mechanism
FOOTBALL 4-5
Cc. TV MONITOR ADJUSTMENTS
For best results be sure the game has been turned on for a while before making any TV monitor adjustments
The TV monitor adjustments are accessible through the access door panel of the game cabinet. These adjustments have to be done while the game is energized. Therefore, only persons familiar with safety measures and repair procedures on electrical equipment should perform them.
The TV monitor should be adjusted only when the picture is distorted or if the contrast or brightness seems out of adjustment.
The monitor’s adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure 4-9 shows the location of the adjustments on both TV monitors used by Atari. Your game contains a TV monitor manufactured to Atari specifications by Motorola, TEC Videoelectronics, or Wells-Gardner. When making adjustments, follow these general guidelines:
BRITE (Brightness)— Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up.
CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being blurred.
HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal Oscillator) — Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture.
VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture.
D. FUSE REPLACEMENT
Football contains eight fuses, five on the power supply assembly in the lower part of the cabinet, one in a clipholder near the power supply, and two on the TV monitor assembly. Power supply fuses are accessible through the access door assembly. TV fuses are also ac-
coms | \\ Car Creer uw 2 FUSES” REMOVE: contrast SRIGHTNESS ani neon bot Gan quen Bow) neneoee a won wo.) \verr Hou VOLTAGE SWITCH (leave In righ postion)
TEC MOTOROLA MODEL TM- 600/623 MODEL M5000/M7000
Figure 4-9 Locations of Adjustments on TV Chassis
4-6 FOOTBALL
cessible through the access door. Replace fuses only with the same type as follows:
Welis-Gardner 19V1001/22V1001 Monitors: 3AG 1.5-amp Slo-Blo 3AG 0.75-amp Slo-Blo TEC TM-600/623 Monitors: 3AG 2-amp and 0.5-amp quick-blow, 250 volts Motorola M5000/M7000 Monitors: 3AG 0.8-amp quick blow, 250 volts Power Supply: Fuses Fl and F2—3AG 3-amp slow-blow, 250 volts Fuses F3 and F4—3AG 2.5-amp slow-blow, 125 volts Fuse F5—3AG 8-amp fast-blow, 125 volts Clip near power supply: (shown in harness schematic) 2.5-amp Slo-Blo
E. CONTROL PANEL REMOVAL (See Figure 4-10) Prior to replacing any removable component from the control panel, follow the steps outlined in Figure 4-10. F. TV MONITOR REMOVAL (See Figure If the TV monitor proves to be at fault, remove the monitor as shown in Figure 4-11.
G. TRACK BALL ASSEMBLY REMOVAL (See Figure 4-12) Refer to paragraph E before replacing the track ball assembly.
H. PLAY SELECT BOARD ASSEMBLY REMOVAL (See Figure 4-13) Refer to paragraph E before replacing the play select board assembly.
CONTROL PANEL REMOVAL
- Unfasten and remove three allen-head screws from control panel.
- Swing the control panel open.
Figure 4-10 Control Panel Removal
FOOTBALL 4-7
TV MONITOR REMOVAL
Remove control panel located to the right of the coin mechanism as illustrated in Figure 4-10. Remove glass playfield shield. Remove cardboard bezel. Open access door. Unplug control panel Molex connectors for both player control panels. Unfasten and remove the two TV monitor carriage bolts.
- Unplug TV monitor chassis connector. FPoeODY
- Slide out TV monitor shelf assembly (the opened control panel is attached to the assembly).
TRACKBALL ASSEMBLY REMOVAL
- Remove contro! panel as illustrated in Figure 4-10.
- Unfasten and remove three (3) trackball 82° flathead countersink ‘screws from assembly.
- Remove the trackball assembly.
BALL REMOVAL 4, Unfasten and remove four (4) countersink machine screws from trackball assembly top plate.
- Remove andlor replace the ball.
STEERING CONTROL PCB
- Unfasten and remove two (2) pan head machine screws associated washers and hex nut from either of two steering PCB assemblies.
- Remove troublesome PCB assembly.
Figure 4-12 Track Ball Assembly Removal
4-8 FOOTBALL
PLAY SELECT BOARD ASSEMBLY REMOVAL
Remove control panel as illustrated in Figure 4-10. Unfasten and remove two pan head machine screws. Unplug Molex connector. Remove board. Replace lamp if necessary.
Figure 4-13 Play Select Board Assembly Removal
NORMALLY CLOSED (N.C.) CONTACTS Sse
Le COUNTERCLOCKWISE TO REMOVE
LIGHT-EMITTING DIODE (L.E.D.) CONTACTS:
NORMALLY OPEN (N.O.) CONTACTS
© Remove all wires from the suspected switch. « Turn the switch counterclockwise while holding NO. bes) NO the cone-shaped nut on the outside of the ' ' DOUBLE-POLE SINGLE-THROW (DPST) SWITCH WITH INTERNAL LED game cabinet. Install a new switch using the reverse procedure. Reconnect the harness wires.
Figure 4-14 LED (LICON) Play Select Pass Switch Removal
FOOTBALL 4-9
J. LED (LICON) PLAY
SELECT/ PASS SWITCH REMOVAL (See Figure 4-14)
Refer to paragraph F before replacing the LED play select/pass pushbutton switch.
The LED switches on the front panel have a very low failure rate. In case either switch should ever be suspect, first test it. To test the switch perform the following steps:
Unlock and open the coin door. Remove the wires from the suspected switch. Set multimeter to ohms scale. Set ohms scale to R x 1, then zero the meter. Bee
MAIN CABINET ASSEMBLY
- Connect multimeter leads to appropriate LED switch contacts. (See Figure 4-14 for designation of switch contacts and meter lead placement.)
- Check contacts (push and release the switch button) for closed and open continuity.
- If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in Figure 4-14.
K. BASE ASSEMBLY REMOVAL (See Figure 4-15) The base assembly to the cabinet may be removed when desired. For example, by removing the cabinet base assembly, the playfield is lower, therefore facilitating the placement of lounge chairs near the player controls like with other Atari cocktail table games.
Figure 4-15 Base Assembly Removal
4-10 FOOTBALL
ILLUSTRATED PARTS CATALOG
The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for the Football game.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this catalog, and serial number of your Football game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
FOOTBALL
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction ff
n tnereot confers o ransfers
NARROW LIP THIS SIDE
Figure 5-1 Football Final Assembly A033580-01_ D
5-2. FOOTBALL
—(
- 2 REQ’‘D
- 4 eean = T= THE FOLLOWING ITEMS ARE NOT SHOWN (19) @5) (26) 23)
GO
FOOTBALL 5-3
Figure 5-1 Football Final Assembly Parts List ATARI’
[item Part Number Qty. Description
| 1 | | A033529-01 | 1 | Cabinet Assy. with Graphics | |
| 2 | A033578-01 | 1 | Assy., Monitor | |
| 3 | A030867-01 | 1 | Assy., R.F. Shield Enclosure | |
| 4 | A009083-01 | 1 | Coin Door Final Assy. | |
| 5 | A007197-01 | 1 | Power Supply Assy. | |
| 6 | 009549-01 | 1 | Coin Door | |
| 7 | A033582-01 | 2 | Assy., Control Panel with Graphics | |
| 8 | 033588-01 | 1 | Shield with Graphics | |
| 9 | 033477-01 | 1 | Bezel with Graphics | |
| 10 | 46-2022502 | 1 | Fuse, 2.5 AMP (Slow Blow) | |
| 1 | 033098-01 | 1 | Stop | |
| 12 | 002728-01 | 2 | Bracket, Panel, Mounting | |
| 13 | 004131-02 | 1 | Fan Grill Mesh | |
| 14 | A022016-01 | 1 | Strain Relief Power Cord Assy. | |
| 15 | 007103-01 | 1 | On-Off Switch Cover | |
| 16 | A030978-01 | 1 | Assy., Atari Football P.C.B. | |
| 17 | A033254-01 | 1 | Assy., R.F. P.C.B. | | |
| 18 | A033323-02 | 1 | Main Harness and Component Assy. | . |
| 20 | 48-004 | 1 | Speaker, 5” | |
| 21 | 000869-01 | 1 | Speaker Grill | my |
| 22 | 032570-01 | 1 | Coin Box Enclosure | |
| 23 | A009548-01 | 1 | Assy., Coin Box Lid | |
| 24 | 46-202302 | 2 | Fuse, 3 AMP (Slow Blow) | |
| 25 | 005233-01 | 1 | Rear Door Seal | |
| 26 | 033613-01 | 1 | Bag, Instruction Manual | |
| 27 | TM-126 | 1 | Tech Manual and IPC | |
| 28 | 78-13025 | AIR | 3M Sealer 5354 | |
| 35 | 73-77015 | 4 | Rivet, 3/16 x .68 (Black) | |
| 36 | 75-5516B | 4 | Bolt, Carr., %4”-20 x 1.00 Lg (Black) | |
| 37 | 75-015S | 12 | Washer, Flat, 4” | |
| 38 | 75-990505S | 4 | Nut, Lock, Shallow Pat., Nylon %4” | |
| 39 | 72-6610S | 23 | Screw, S.M.P.H., Phil., #6 x 5/8” Lg. | |
| 40 | 72-6812S | 8 | Screw, S.M | .» Phil., #8 x 3/4” Lg. |
| A | 72-6810S | 6 | Screw, S.M.P.H., Phil., #8 x 5/8” Lg. | |
| 42 | 82-8516 | 6 | Screw, Mach., Allen, Button Hd., %4-20 x 1.00 Lg. | |
| 43 | 75-935 | 2 | Wingnut, Steel, 4-20 | ’ |
| 44 | 72-6012S | 1 | Screw, S.M.P.H., Phil., #10 x 3/4” Lg. | |
| 45 | 75-010S | 3 | Washer, Flat, #10 (Steel) | |
| 46 | 75-5520B | 8 | Carr. Bolt, %”-20 x 1.25” Lg. (Black) | > |
| 47 | 75-045S | 2 | Washer, Splitlock, 4” | |
| 48 | 75-915 | 6 | Nut, Mach., Hex, %”-20 | |
| 49 | 75-931 | 8 | Wingnut, Steel, 10-24 | |
| 50 | 75-5120B | 2 | Bolt, Carriage, 10-24 x 1.25 Lg. | |
| 51 | 75-040S | 2 | Washer, Splitlock #10 | |
| 52 | 72-6608S | 4 | Screw, S.M.P.H., Phil. #6 x %2” Lg. |
5-4 FOOTBALL
NOTICE TO ALL PERSONS RECE!
EN ep
FOOTBALL 5-5 Figure 5-2 TV Monitor Assembly A033578-01_ D APPLY R.T.V SILICONE RUBBER (GE 108 OR yi, 8: ZEQD EQUIV) AS SHOWN, ON ONE SIDE.
LOCATION OF COPYRIGHT DECAL MAY
CHANGE AT THE DISCRETION OF MANUFAC- TURING.
Figure 5-2. TV Monitor Assembly Parts List ATARI’
Part Number Description
| 1 | A033065-01 | 1 | Assy, Monitor Support |
| 2 | 90-032 | 1 | Monitor 23” Diagonal Black and White |
| 3 | 005594-01 | 4 | Monitor Tie-Down Brkt. |
| 4 | 48-004 | 1 | Speaker 5” |
| 5 | 000869-01 | 1 | Speaker Grill |
| 6 | 73-77015 | 8 | Rivet 3/16 x .68 (Black) |
| 7 | 72-6610S | 6 | Screw SMPH #6 x 5/8” Lg. |
| 8 | 72-6812S | 8 | Screw SMPH #8 x 3/4” Lg. |
| 9 | 006313-03 | 1 | | Copyright Decal 1978 |
| 10 | 004131-02 | 1 | Fan Grill, Mesh |
(+ Were: communications Company
5-6 FOOTBALL
NOTICE TO Att PERSONS RECEIVING THIS DRAWING
©
ee Geef
Figure 5-3 Type B Power Supply A007197-01 D
FOOTBALL 5-7
ATARI’ Figure 5-3 Type B Power Supply Parts List
L
| Item | Part Number | Qty. | Description |
| 1 | A009266-01 | 1 | Power Supply Base Weldment Assembly |
| 2 | A006886-01 | 1 | Transformer Termination Assembly “Type B” |
| 3 | 29-053 | 1 | Cap., Sprague Electrolytic 26,000 pf @ 15V |
| 4 | 78-70501SC | 1 | Brkt., Cap. Mtg. Sprague #4586-48 |
| 5 | A006555-01 | 1 | P.C. Board Rectifier |
| 7 | 79-4411004 | 5 | Fuse Holder, Panel Mounting |
| 8 | 41-2003 | 1 | Filter, Power Line, 5 AMP |
| 9 | A006958-01 | AIR | Volt Selection Block 95V |
| 10 | A006958-02 | AIR | Volt Selection Block 110V |
| "1 | A006958-03 | AIR | Volt Selection Block 205V |
| 12 | A006958-04 | AIR | Volt Selection Block 220V | |
| 13 | 78-2708 | 1 | Grommet, Plastic |
| 14 | 72-1810S | 9 | Screw Pan Hd., #8-32 x 5/8” Lg. |
| 16 | 75-048 | Q | Washer, Split-Lock #8 |
| 17 | 75-9188 | 9 | Nut Hex #8 |
| 18 | 75-018S | 8 | Washer Flat #8 |
| 19 | A007192-01 | 1 | Power Switch Termination |
| 20 | A007444-01 | 1 | Power In Harness |
| 21 | 46-203801 | 1 | Fuse, 8 AMP, 125V, 3 AG Fast Acting |
| 22 | 46-201251 | 2 | Fuse, 2% AMP, 125V, Slow Acting |
© é ver41 communeatons Company
5-8 FOOTBALL
©) 2 PLCS @21)
2 PLCS @3)
®
@)
NOTICE TO ALL PEFSONS RECEIVING THIS DRAWING CONFIDENTIAL’ Reproduction. specific. written permission of California. Th
‘the co fen license, no right to reproduce this drat ‘the subjéct matter thereof uniess by wri With oF written permission from the corporation,
- 6 PLCS
- 2 PLCS
- 2 PLCS
- 2 PLCS
)
YEL/BK (2)4 Pics BK/YEL
Figure 5-4 Coin Door Assembly A009083-01 F
FOOTBALL 5-9
A ATARI
Part Number
1 A007637-01 A007637-02 A007637-03 A007637-04 A007637-05 A007637-06 A007637-07
2 75-9165 3 A030362-01 4 A007640-01 5 A002465-01 6 004320-01 7 004341-01 8 004344-01 9 004340-01 10 004337-01 1 004338-01 12 004336-01 13 004326-01 14 75-046 15 006904-01 16 007359-01 17 70-11-47 18 73-3008 19 75-9914001 20 75-026S 21 75-00516 22 008629-01 23 71-2118 24 71-1225CU 71-125FB 71-1205FF 71-1201MG 71-1201KS 71-1210PE 71-1220CA 25 007753-01 26 A007638-01 27 A006921-01
L VAN GPAONAANANAANNANAANAA
Ref. Ref. Ref. Ref. Ref. Ref. Figure 5-4 Coin Door Assembly Parts List
Description
Front Bezel Assy.—Used only on -01 Coin Door Assy. Front Bezel Assy.—Used only on -02 Coin Door Assy. Front Bezel Assy.—Used only on -03 Coin Door Assy. Front Bezel Assy.—Used only on -04 Coin Door Assy. Front Bezel Assy.—Used only on -05 Coin Door Assy. Front Bezel Assy.—Used only on -06 Coin Door Assy. Front Bezel Assy.—Used only on -07 Coin Door Assy. See Figure 5-5 Nut, 6-32 Coin Lock-Out Assembly, See Figure 5-6 Coin Switch Assembly, See Figure 5-7 Coin Counter Assembly Coin Door Weldment Secondary Coin Chute Key Loop Spring Return Bracket, Wire Form Lock-Out, Wire Form, R.H. Lock-Out, Wire Form, L.H. Button, Scavenger Lock Washer, #6 Spacer Lamp Socket Lamp Retaining “C” Ring, Truarc #5103-25 Seif-Threading Nut, Tinnerman #SR188006 Washer, #6 Kepnut, Style 842, Sti., 6-32 Spring Lock Assembly, Hudson Lock Coin Mechanism for American Quarter Only Coin Mechanism for Belgian 5 Francs Only Coin Mechanism for German Mark Only Coin Mechanism for Swedish Krona Only Coin Mechanism for Japanese 100 Yen Only Coin Mechanism for English 10 Pence Only Coin Mechanism for Australian 20-Cent Piece Only Plate, Anti-Probe Switch Assembly, Slam Harness Assembly
5-10 FOOTBALL
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL; ‘Reproduction’ forbidden without the Specie. wnt permission of Alar ne, "Sunnyvale, Galifornia. This drawing Is only conditionally issued, and neither receipt nor possession thereof conters or transfers any right in, or license to use, the subject matter of the Sardi oF ay design or technical information shown thereon, nor any right to reproduce this drawing or any Dar {herec? except for manutacture by vendors of Atal tncor porated ana for manufacture under the corporations wt sA8e, No right to reproduce this. is granted ore subjset matter hereot unless by writer agreement swith or written permission from tha corporation
H 8
t
© @ @
ATARI Item Part Number Qty. Description
| 1 | 004328-01 | 1 | Bezel |
| 2 | See below | 2 | Ring |
| 3 | 004331-01 | 2 | Coin Shield |
| 4 | 004332-01 | 2 | Primary Coin Chute |
| 5 | 004327-01 | 2 | Bearing, Scavenger Button |
| 6 | 004329-01 | 2 | Clamp, Price Plate |
| 7 | See Below | 1 | Price Plate |
| 8 | 73-3009 | 2 | Retaining “C” Ring, Truarc #5103-37 |
| 9 | 72-1604S | 4 | Mach. Ser., 6-32 x % Lg. Pan Hd., Phil |
| 10 | 75-046 | 2 | Washer, #6, Split-Lock |
| 1 | 75-9914001 | 6 | Self-Threading Nut, Tinnerman #SR188006 |
FRONT BEZEL | ITEM2 ITEM7 DENOMINATION ASSY VERSION
| 01 | 004330-01 | 004343-01 | 25¢ |
| -02 | 004330-01 | 004343-06 | 5 FR |
| -03 | 009153-01 | 004343-04 | 1DM |
| -04 | 004330-01 | 004343-03 | 1KR |
| -05 | 009520-01 | 004343-05 | 100 Y |
| -06 | 007752-01 | 004343-02 | 10P |
| 07 | 007752-01 | 004343-07 | 20¢ AUST. |
© A warner Communications Company
Figure 5-5 Front Bezel Assembly A007637-01 thru -07 D
FOOTBALL 5-11
RELAY COIL (PER A007639-01) NOTES:
- Goil data: 10 VDC +2, 50. resistance current 200 ma maximum.
- Manufacturer: Coin Mech, Inc.
DETAIL OF RELAY COIL (A007639-01)
Figure 5-6 Coin Lockout Assembly A030362-01 A
NOTICE TO Ail PERSONS RECEIVING THIS DRAWING
Shy Hight in thereon, nor an igh 0 reproduce ths {hereof except for manuiacture by vendors of i porated and for manufacture ander the corpo no righ fe reproduce this craw (od ict matter thereof unless by writien agreement ten permission ‘tom the corporation a “ine ub wih or wel Parts List
ITEM | PART N' DESCRIPTION jt eave. | esenenon —_] ory [1 | oowezor | _switenmoumting Pte |_| Switch Mounting Plate 65-441C _Switch, Omron C-5G3-3 72-HA4412 “Screw A MS, #4-40 x 34LG Roll-Tight Self. Tapping
Wireform, Cherry
Figure 5-7 Coin Switch Assembly A007640-01 D
5-12 FOOTBALL
gy esa
NOTICE TO ALi. PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbidden without the Specific. written permission of Ata Sunnyvale, Galitesnia” This drawing Is only conditionally issued, and Reltner receipt nor possession there! eanvers oy transfers any right in, oF Hicense to uso, the sudject matter o} the Grawing cr any design or technical Information. shown thereon, nor any right to reproduce tnis drawing or any part thereo!, except for manulaclure by vendors ol Atari, incor orated and for manulacture under the corpor fan license, no sight to reproduce this drawing is forthe subject matter thereof unless by written ag Wwith or written permission tom the corporation Ng Nem
Figure 5-8 Control Panel Assembly A033582-01 D
FOOTBALL 5-13
A ATARI’ Figure 5-8 Control Panel Assembly Parts List
| Item | Part Number | Qty. |
| 1 | A033360-01 | 1 |
| 2 | A033324-01 | 1 |
| 3 | A033729-01 | 1 |
| 4 | 033346-01 | 1 |
| 5 | 033097-01 | 1 |
| 6 | 033345-01 | 1 |
| 7 | 001856-01 | 1 |
| 8 | 75-990505S | 3 |
| 9 | 75-5512N | 3 |
| 10 | 62-002 | 1 |
| 1 | 75-015S | 3 |
| 12 | 75-040S | 6 |
| 13 | 75-910S | 6 |
| 14 | 75-010S | 6 |
Description
Assy., Trackball Assy., Control Harness Assy., P.C.B. Control Panel with Graphics Support, Play Selection Panel Panel, Play Select with Graphics Bushing, Alum. Nut, Hex, %-20 Nylon Locking Bolt, Carriage, 74-20 x 3/4” Lg. LED Switch, Lighted Washer, Flat, 4” Washer, Splitlock, #10 Nut, Hex, #10-32 Washer, Flat, #10
Avtar Conmincatons Company
5-14 FOOTBALL
Soy
NOTICE TO ALi PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Roproduction,Tovbidden. without he specific weitteh, permission innyvale, neither receipt nor posses ious Sy right nor er of te ‘rawing oF any ‘desig formation shown there any pa Dotated endfor manufacture under the corporation's wi {emileerse, no righ to reproduce this deeming 's granted Binet rere yma aieomet with oF written permission Irom the corporation,
bh
ise] ONCE ON £p,
Figure 5-9 Track Ball Assembly 033360-01 D
FOOTBALL 5-15
Figure 5-9 Track Ball Assembly Parts List ATARI
T
| Item | Part Number | Qty. | Description |
| 1 | 033355-01 | 1 | Plate, Base |
| 2 | 033356-01 | 1 | Plate, Top |
| 3 | 033357-01 | 1 | Plate, Cover |
| 4 | 033358-01 | 1 | Post, Corner |
| 5 | 033359-01 | 2 | Post, End |
| 6 | 033361-01 | 2 | Bracket, PCB |
| 7 | 033362-01 | 2 | Shaft, Roller |
| 8 | 033363-01 | 1 | Stand Off |
| 9 | 033364-01 | 1 | Post, Adjustable |
| 10 | 033365-01 | 1 | Spacer |
| an | 000616-01 | 2 | Hub, Light |
| 12 | 033366-01 | 1 | Ball, 472 Dia., Rubber |
| 13 | 74-5404NN | 4 | Spacer, 1/8 1.D., 4 O.D. x % LG, Nylon |
| 14 | A009060-01 | 2 | PCB Assy, Steering |
| 15 | 76-13003 | 5 | Bearing, Fafnir S3K or Equiv. (N.D.-R6) |
| 16 | 73-3006 | 2 | ‘E’ Ring, Truarc #5144-37 |
| 17 | 72-8808 | 9 | Screw, Mach, Cap, Hex Soc. Hd #8-32 x ¥2 LG |
| 18 | 72-1006S | 2 | Screw, Mach, Pan Hd, X-Rec, #10-32 x 3/8 LG |
| 19 | 72-1606S | 4 | Screw, Mach, Pan Hd, X-Rec, #6-32 x 3/8 LG |
| 20 | 72-1410S | 4 | Screw, Mach, Pan Hd, X-Rec, #4-40 x 5/8 LG |
| 21 | 72-8920S | 1 | Screw, Mach, Cap, Hex Soc. Hd, #3/8-16 x 1% LG |
| 22 | 75-3806S | 4 | Screw, Mach, 82° Flat, C’Sunk Hd, X-Rec, #8-32 x 3/8 LG |
| 23 | 75-3608S | 3 | Screw, Mach, 82° Flat, C’Sunk Hd, X-Rec, #6-32 x 2 LG |
| 25 | 75-044S | 4 | Washer, Split Lock, Spring, #4 |
| 26 | 75-046S | 4 | Washer, Split Lock, Spring, #6 |
| 27 | 75-048S | 9 | Washer, Split Lock, Spring, #8 |
| 28 | 75-040S | 2 | Washer, Split Lock, Spring, #10 |
| 29 | 75-041S | 1 | Washer, Split Lock, Spring, 3/8 |
| 31 | 75-010S | 2 | Washer, Flat, Plain, #10 |
| 32 | 75-018S | 2 | Washer, Flat, Plain, #8 |
| 33 | 75-016S | 3 | Washer, Flat, Plain, #6 |
| 35 | 75-914S | 4 | Nut, Machine, Hex, Std. Pat., #4-40 |
| 36 | 75-916S | 3 | Nut, Machine, Hex, Std. Pat., #6-32 |
| 37 | 75-919S | 1 | Nut, Machine, Hex, Std. Pat., 3/8-16 |
@ 4 Warne: Communications Company
5-16 FOOTBALL
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction ‘lorbidéen without the any tight in, or license tp use, the subject malter of the drawing or any design technical tiormation shown 1, Nor any right fo reproduce this Grawing or any oar! xcept for manuacture by vendors of Atari, Inoorsnd for manufacture under the corporation's writ 2, no right to repraduce thls drawing is granted ‘or the sub|éct matter thereof Uniess by written agreement with or written permission from the corporation,
3 POSITION AMP PLUG AND PINS 1BK 2GN 3W
Parts List
Item Part Number Qty. Description
| 1 | 54-410 | 1 | Power Cord, 12 Foot |
| 2 | 78-2112P | 1 | Strain Relief |
| 3 | 033211-01 | 1 | Washer, Centering |
| 4 | 79-58110 | 1 | AMP Plug, 3 Pos #1-480700-0 |
| 5 | 79-20123 | 3 | AMP Pin #350547-1 |
| 6 | 78-25002 | 1 | Screw-down Tie Wrap (#10 Screw) |
Figure 5-10 Strain Relief Power Cord Assembly A033016-01 B
FOOTBALL 5-17
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific. written permission of Atari, Inc,” Sunnyvale, California. This f Ihnor possession thereat confers or tanstars ‘any design or technical information shown, ‘ny right to reproduce this drawing or any part pt for manufacture by vendors of Atari, incor
Part Number k. Description
61-062A Toggle Switch, DPST Carling Switch #2GK54 006450-01 Mounting Plate, On-Off Switch
Figure 5-11 On/Off Switch Assembly A006449-01
Parts List
Part Number F Description
| 1 | 030168-01 | 1 | Bracket, Mounting |
| 2 | 69-001 | 1 | Switch, Test DPDT |
| 3 | 73-77001 | 2 | Pop Rivet, .125 DIA x .375 Lg |
| 4 | 19-9032 | 1 |
Rheostat, Wire Wound (OHMITE MOD “E” #0110)
Figure 5-12 Self-Test Switch/Volume Bracket Assembly A030169-01
5-18 FOOTBALL
- bp G PLUNGER
RED LENS PUSHBUTTON CONTACTS *To lock switch in “on” Position, pull out plunger
Figure 5-13 Interlock Switch Assembly
PIN LAYOUT 62-002
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction” forbidaen without the specific written permission of Atari, Ine,” Sunnyvale, Calitornia’ This drawing ti Only conditionally issued, and ipt nor possession thereof conters or ranaters ‘oF license to use, the subject matter of the ‘any design or technical information shown thereon, nor any right to reproduce this drawing or any part therwol except oF manufacture by vendors ob Ata near porated and for manulacture under the corporation's wrt fen license, no rignt to reproduce this drawing is granted or tne sub mater thereat uniess by wren agreement ‘with of wilten permission trom ihe corporation
Figure 5-14 LED Pushbutton Switch Assembly (Red) 60-002
FOOTBALL 5-19
NOTICE 10 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbidden without the pez, writen, permission ot Atari Ine,” Sunnyvale, iMornia. Thie drawing is only conditional hettherreceipt nor possession thers! conte'sar anaters any right in, or license To Use, the subject matter of the erawing of any design or technical information shown thereon, nor any right to reproduce this drawing or any park thereat, except or ma facture by vendors of Alar, incor ure anaes the corporalon's wit reduce this drawing is granted forthe subject matter thereot uniess by written agreement ‘with OF wiltlen permission rom the corporation,
A006555 t
2 PLCS.
cre|
Parts List
Item Part Number Qty. Description
1 006556-01 1 P.C. Board 2 31-MR750 2 Diode, MR750 CR1,CR2
Figure 5-15 Rectifier PCB Assembly A006555-01
5-20 FOOTBALL Cc
TRACES SHOWN ARE ON OPPOSITE SIDE
OStEEOA Ga YAI92Id_JJABTOO? A] ro-ogseeo BY 0 IAATA
CRI eRe. ARB cre °
L >/ + @PL
ASSEMBLY
( cRI | tf ' 3 4
| * | + | | | —e | + | 2 | eee |
Y ral NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL’ Reproguction Torbiggen. without the Bierman aauing i oni canlonal satey and CRS ‘rpossessionthereol confers or transfers 4 _ e
Sienstrataioeren treo era 4 _ 4 7
SCHEMATIC
Parts List
| Item | Part Number | Qty. | Description | |
| 1 | 033730-01 | 1 | P.C. Board | |
| 2 | 38-MV5053 | 4 | LED, MV5053 | CR1-4 |
| 3 | 79-4312 | 6 | Socket, Lamp, Miniature, Right Angle | |
| 4 | 79-58281 | 1 | Header, 7 Pin, Right Angle |
Figure 5-16 Play Select PCB Assembly A033729-01 D
FOOTBALL 5-21
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING Specitic written permission of Alar. Inc... Sunnyvale, California. This drawing ts on'y conditionally issued, and Fralthe! receipt nor possession thereo! conters or translers any right Jn, oF license lo use, the subject matter of the Grawing 97 any design or tachaical information. shown thereon, nor any right to reprocuce this drawing or any part thereof, except for manutacture by vendors of Alar ncor
Parts List
Item Part Number Qty. Description
| 1 | 030835-01 | 1 | P.C. Board |
| 2 | 20-1016 | 28 | Capacitor, Monolithic, .1 nf, 50V |
| 3 | 41-3003 | 14 | Inductor, 100 zh |
| 4 | 52-003 | 13 | dumper, .600 Centers |
| 5 | 75-E6106081 | 3 | Wingscrew, #6-32 x ¥ Lg. |
| 6 | 75-992501 | 3 | Fastener, %4-Turn, #6-32, Stainless Steel |
| 7 | 79-517222 | 1 | Connector, 44-Pin, P.C. Mount |
Figure 5-17 RF Shield PCB Assembly A033254-01
5-22 FOOTBALL
{NOTICE 10 ALL PERSONS RECEIVING THIS DRAWING L: Reproduction larbidden without the iten permission of Atari, inc. Sunnyvale, his drawing (3 only conditionally issued. and neither receipt nor possession thereol confers or translers any right in, or license 0 usa, the subject matter of the Grawing or any dasign ee technical. information. snown thereon, norany right to reproduce this drawing or any part exzept for manulacture by vendors of Atar, feo porated and for manufacture under the corporalion's wrt fen licesse, no right to reproduce this deawing is granted br the subject matter thereo! Uniess by written ageaement with oF written permission from the corporation,
CAC
37, 40,100 LOCATION. PROGRAM MEMORY CHART -01 (PROM) | -02 (ROM) [ ALT CKTRY 01
FO. a a caso [ | —ossres |
033723 33722 03372 (933720 033028
at 038024 033719
53718
i 738025 OSa7i7
Mt Ni (038027 a
Figure 5-18 (038028.
PERMANENT-MARK “1” OR “02” AFTER A030977 (01 for PROM, -02 for ROM).
Football PCB Assembly A030977-01, 02
FOOTBALL 5-23
A, ATARI’ Figure 5-18 Football PCB Assembly Parts List -01 Version -01, -02 Versions
| Item | Part Number | Qty. | Description | |
| 1 | 030978-01 | 1 | P.C. Board | |
| 2 | 10-5101 | 3 | Res., Carbon, 5%, %W, 100 Ohm | R3-5 |
| 3 | 10-5331 | 3 | Res., Carbon, 5%, 14W, 330 Ohm | R7, 8, 21 |
| 4 | 10-5471 | 2 | Res., Carbon, 5%, %4W, 470 Ohm | R23, 26 |
| 5 | 10-5102 | 19 | Res., Carbon, 5%, %4W, 1K Ohm | R1,2,6,9, 11-13,18,27-31 |
38,40,43,44,67,68
| 6 | 10-5152 | 1 | Res., Carbon, 5%, “%W, 1.5K Ohm | R22 |
| 7 | 10-5222 | 4 | Res., Carbon, 5%, YW, 2.2K Ohm | R19, 32:34 |
| 8 | 10-5392 | 1 | Res., Carbon, 5%, %4W, 3.9K Ohm | R20 |
| 9 | 10-5562 | 1 | Res., Carbon, 5%, %4W, 5.6K Ohm = R72. | |
| 10 | 10-5103 | 25 | Res., Carbon, 5%, 44W, 10K Ohm | —_——R'10,39,41,42,45-65 |
| 1 | 10-5223 | 1 | Res., Carbon, 5%, %4W, 22K Ohm | R36 |
| 12 | 10-5473 | 3 | Res., Carbon, 5%, %W, 47K Ohm | R70,71,74 |
| 13 | 10-5563 | 1 | Res., Carbon, 5%, “%W, 56K Ohm | R15 |
| 14 | 10-5104 | 1 | Res., Carbon, 5%, Y4W, 100K Ohm = R14 | |
| 15 | 10-5224 | 2 | Res., Carbon, 5%, %W, 220K Ohm | _——R16,73 |
| 16 | 10-5334 | 1 | Res., Carbon, 5%, YW, 330K Ohm = R35 | |
| 17 | 10-5394 | 1 | Res., Carbon, 5%, %4W, 390K Ohms | R17 |
| 19 | 11-5330 | 4 | Res., Carbon, 5%, ¥2W, 33 Ohm | R24,25,66,69 |
| 22 | 19-315503 | 1 | Trimpot, 50K Ohm | R75 |
| 23 | 19-805W4P0 | 1 | Res., Wirewound, 10W, 4 Ohm | R37 |
| 25 | 24-250106 | 2 | Cap., Elec., 25V, 10 pf | 35,50 |
| 26 | 24-250108 | 1 | Cap., Elec., 25V, 1000 pf | C58 |
| 27 | 24-250477 | 1 | Cap., Elec., 25V, 470 uf | C23 |
| 28 | 24-250478 | 1 | Cap., Elec., 25V, 4700 uf | C62 |
| 31 | 27-250102 | 2 | Cap., Cer., 25V, .001 yf | C54,61 |
| 32 | 27-250103 | 14 | Cap., Cer., 25V, .01 pf | C27,28,33,34,38- |
41,48,49,51-53,56
| 33 | 27-250104 | 39 | Cap., Cer., 25V, .1 uf | C1-11,13-22,24-26,29 |
32,36,37,42- 46, 55,57,60,63
| 34 | 27-250224 | 1 | Cap., Cer., 25V, .22 uf | C47 |
| 36 | 28-101101 | 1 | Cap., Mica, 100V, 100 pf | C12 |
| 37 | 28-101221 | 1 | Cap., Mica, 100V, 220 pf | C59 |
| 4 | 31-1N4001 | 2 | Diode, 1N4001 | CR1,2 |
| 44 | 33-2N3644 | 3 | Transistor, 2N3644 | Q5-7 |
| 46 | 34-2N3643, | 7 | Transistor, 2N3643 | Q1,3,4,8-11 |
| 47 | 34-2N6044 | 1 | Transistor, 2N6044 | Q2 |
| 49 | 37-7400 | 2 | Integrated Circuit, 7400 | C3,K8 |
| 50 | 37-7402 | 2 | Integrated Circuit, 7402 | D7,K7 |
| 51 | 37-7404 | 3 | Integrated Circuit, 7404 | P2,N4,P7 |
| 52 | 37-7408 | 2 | (Integrated Circuit, 7408 | D8,L8 |
| 53 | 37-7410 | 2 | Integrated Circuit, 7410 | J7,N9 |
| 54 | 37-7414 | 3 | Integrated Circuit, 7414 | D3,B7,J10 |
| 55 | 37-7430 | 1 | Integrated Circuit, 7430 | H6 |
| 56 | 37-7432 | 5 | Integrated Circuit, 7432 | M3,P3,B4,C4,B5 |
| 57 | | 37-7442 | 3 | Integrated Circuit, 7442 | B3,E3,L10 |
> warner Communications Company
5-24 FOOTBALL
Figure 5-19 Football PCB Assembly Parts List AT ARI’ -01 Version
[tem Part Number Qty. Description
| 58 | 37-7474 | 5 | Integrated Circuit, 7474 | N5,E9,J9,M9,P9 |
| 59 | 37-74874 | 1 | Integrated Circuit, 74S74 | L7 |
| 60 | 37-74LS83 | 3 | Integrated Circuit, 74LS83 | F5,H5,H7 |
| 61 | 37-74LS86 | 3 | Integrated Circuit, 74LS86 | D6,A7,M8 |
| 62 | 37-7490 | 1 | Integrated Circuit, 7490 | A4 |
| 63 | 37-74LS151 | 1 | Integrated Circuit, 74LS151 | H8 |
| 64 | 37-74LS153 | 5 | Integrated Circuit, 74LS153 | F3,H3,J3,K3,L3 |
| 65 | 37-74LS157 | 4 | Integrated Circuit, 74LS157 | B6,C6,E6,N8. |
| 66 | 37-74LS163A | 2 | Integrated Circuit, 74LS163A | K5,J6 |
| 67 | 37-74LS164 | 3 | Integrated Circuit, 74LS164 | A8,B8,J8 |
| 68 | 37-74LS166 | 1 | Integrated Circuit, 74LS166 | AG |
| 69 | 37-74LS174 | 2 | Integrated Circuit, 74LS174 | E8,F9 |
| 70 | 37-74LS175 | 1 | Integrated Circuit, 74LS175 | L6 |
| 71 | 37-74LS191 | 4 | Integrated Circuit, 74LS191 | D9,H9,D10,H10 |
| 72 | 37-74195 | 1 | Integrated Circuit, 74195 | P8 |
| 73 | 37-74LS244 | 9 | Integrated Circuit, 74LS244 | B1,C1,E2,L2,N3,L4,M4, |
E10,F10
| 74 | 37-74LS374 | 7 | Integrated Circuit, 74LS374 | D4,E4,J5,F6,F7,M7,F8 |
| 76 | 37-LM323K | 1 | Regulator LM323 | |
| 77 | 37-LM324 | 1 | Op Amp LM324 | AQ |
| 78 | 37-555 | 1 | Timer 555 | cg |
| 79 | 37-TDA1004 | 1 | Audio Amp TDA1004 | Alt |
| 80 | 37-7812 | 1 | Regulator 7812 | |
| 81 | 37-8728 | 2 | Integrated Circuit 8T28 | E5,E7 |
| 82 | 37-9316 | 5 | Integrated Circuit 9316 | M5,P5,M6,N6,P6 |
| 83 | 37-9321 | 1 | Integrated Circuit 9321 | c7 |
| 86 | 62-001 | 1 | Switch, SPST, Mom | |
| 87 | 66-118PIT | 1 | Switch, SPST, X8, DIP | K10 |
| 88 | 72-1608C | 2 | Screw, Pan Hd., #6-32 x 1 Lg., Cres. | |
| 89 | 75-016C | 2 | Washer, Flat, #6, Cres | |
| 90 | 75-056 | 2 | Washer, Lock, Int. Star, #6 | |
| 91 | 75-916C | 2 | Nut, Hex, #6-32, Cres. | |
| 93 | 78-16005 | 1 | Silpad (LM323) | |
| 94 | 78-06001 | 1 | Heatsink (LM323) | |
| 95 | 009470-01 | 1 | Heatsink (TDA1004) | |
| 96 | 78-13016 | AR | Cement (TDA1004 Heatsink) | |
| 98 | 79-42040 | 1 | Socket, 40-Pin, Med. Insertion | C2 |
| 100 | 90-102 | 1 | Crystal, 12.096 MHz | Y1 |
| 102 | 90-6010 | | | Microprocessor | C2 |
| 103 | 90-7008 | 1 | RAM | K6 |
| 104 | 90-7031 | 8 | RAM | F2,H2,J2,K2,F4,H4, |
J4,K4
| 105 | 90-7033 | 2 | RAM | M2,N2 |
| 107 | 009402-01 | 1 | PROM, Sync (828129) | L5 |
| 108 | 033029-01 | 1 | PROM, Alpha Numerics (828137) | N7 |
| 109 | 033030-01 | 1 | PROM, Graphics, LSB (82S131) | C5 |
| 110 | 033031-01 | 1 | PROM, Graphics, MSB_ (82131) | DS |
© Aware, Conmunicanons Company
FOOTBALL 5-25
Figure 5-18 Football PCB Assembly Parts List ATARI"
Item Part Number | Qty. Description -01 Version
| 111 | 033020-01 | 1 | PROM, Program (828185) | D1 |
| 112 | 033021-01 | 1 | PROM, Program (825185) | =at |
| 113 | 033022-01 | 1 | PROM, Program (828185) | Fi |
| 114 | 033023-01 | 1 | PROM, Program (828185) | H1 |
| 115 | 033024-01 | 1 | PROM, Program (828185) | J1 |
| 116 | 033025-01 | 1 | PROM, Program (828185) | K1 |
e
| 120 | 033717-01 | 1 | PROM, Program (828137) | 8 . | K1 |
| 121 | 0337 18-01 | 1 | PROM, Program (828137) | @ > | KO |
| 122 | 033719-01 | 1 | PROM, Program (828137) | 2a | J1 |
| 123 | 033720-01 | 1 | PROM, Program (828137) s Ff | JO |
| 124 | 033721-01 | 1 | PROM, Program (828137) | HE | Hi |
| 125 | 033722-01 | 1 | PROM, Program (825137) _ Oo | HO |
| 126 | 033723-01 | 1 | PROM, Program (828137) | Gs | Ft |
| 127 | 033724-01 | 1 | PROM, Program (828137) z 9 | FO |
| 128 | 033725-01 | 1 | PROM, Program (828137) } Oa | =a) |
| 129 | 033726-01 | 1 | PROM, Program (828137)| Gs | £0 |
| 130 | 033727-01 | 1 | PROM, Program (828137) a é | 01 |
| 131 | 033728-01 | 1 | PROM, Program (82S137) J} oo | DO |
-02 Version
| 417 | 033026-01 | 1 | ROM, Program (8316E) | Mi |
| 118 | 033027-01 | 1 | ROM, Program (8316E) | N1 |
| 119 | 033028-01 | 1 | ROM, Program (8316E) | P1 |
LL
5-26 FOOTBALL
APPENDIX A Reference Drawings
List of Reference Drawings
Description Figure No.
Football PCB Schematic Diagram... 0.000600 Type B Power Supply Schematic Diagram Coin Door Schematic Diagram. ..... 2-000 eee Football Game Harness Schematic Diagram ... 2.0... eve ee eee aR OHH
Football Game Harness Layout ........00-00 000 0c cette teeta
RRO PRIZ rary
al
| a7 | Re | | | mee | bs |
@ 1 02 93 PE
| 330 | 330 | ce | cee |
nz) ‘o| Po
| Ne | “I | N4& | N& | KET gate | Te | ceT gai TC |
| {JE | 20% | * | P02 | cp BIN CNTR | ce BIN CNTR | |
| 04 | 12.090 | O4 | O4 | Q6 ai az 03 MR | Q6 1 02 23 MR | |
| MHz | ra fis fiz. er | ia fia 2 pw OF |
tal ARO RRIZ :
¥ Zz = a Es
QB Oi G2 G3 MR QO al 42.43 MR 14 [3 fiz ny ie 13 fiz ya Or RRO PRIZ
+
a 2232 i 2234 2a38 Prd ~ we
R37 7
4n,}OW
«K K]+sv (PULL) LM
| +lOV (UNREG) |B | 2} | 323 | 5 a | +5V |
Ci-ils 14-18, 20-22,24-20,
| car | + [ozs | 29-31, 36,37,42,46 |
| - | 470 | .1 (BYPASS) |
A-2 FOOTBALL
PRIZ
= nie = ae
| 3 |4 |5 |e oo | au | H |
[22 Pi P2 PS Pe O4 cer Pr Lo nv 2No8
| CET 93ie TE | 2H | 7A |
| 2lop BIN CNTR | of | 04 |
a 1 Q2 QS PT a2v—5 [o£ — 30 BRIZ oa
zr Oo 9 on es
| vBLANK— | 5} 07 | 9 | 5 | 2a | NBLANK |
| 1 | 04 | a | fl, | ||
| (26 | Ae Ls | 2Q | VBLANK | ||
| eau | 2555 | fo | 4 | va} | |
| al. | 190 | es | nn | ||
| 32 | At Ow | re !@ | VRESET | ||
| ev | —+4 a3 oe on u | 13] 4375 aa}? — ennscreen | |||
| 4y | —Yaz®z | aalls | |||
| ob] | Or | FIF | lio | ||
| 2N | Al | 12 | 3Qh?—vsync | ||
| ° | 2] 55 | 1 | |||
| iw | —Slag | 3att |
cel CER cK \4 of te.svac ct [a] t ARIZ
~ 756H
7al2 cRI
| asvac [wha | > | + | ¢— | tizv |
IN4OO1
| +{cso | |c4s | LasT DES | ||
| eRe | = | - | ae | —_— |
asvac [x20 TtBYRASS) ces
| INQOOL 4 vigy | = | = | cr |
+) C62 ai ‘4,700 Rs = eal
25VAC CT GND ¥ iat
2/22
= SYNC, POWER
NOTICE 10 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction” forbidden without the ine. Sunnyvale, r
Figure 1 Football PCB Schematic Diagram Sheet 1 of 6 030977-01, 02
FOOTBALL A3
7" AgUSIS_@p—+ Waive. PRSEL 4 @QHQHO ce" | ss . a), 1p? —sewoccrecoeeL
- npusi¢——BJe 2 TD? ex ; WTKER ais [28 agusis aausis —!415, ; Is> Le -@ seus], 2 warenos ABIG. ABUSI4. 5 irs PRZ ABS zeus 7 PROGSELI apie [22 FO seven bg 8 3s tg so decone 2 oy Squuer 20 © spas iz [E44] 6 ABIL 2 ABUSIL PRE a = ABUSII asy asiop? 2 S| fy $s agusio sl P asusio 45y a aso r® 4} fe He apuse paz! fe 5 spuse a o sO i ase ‘ABB 2 18 ABUSE 64h LS 3 ABUSE i c2 ssv 20] 2) rn ~ jue Ge = q WeERBDS py Reser 20-G010 LY i ‘DISABLE = B62 Bee <9 ROM creer mae TNE ur RPERDOS rR. a7 [te fet 2 agus? aon 275 2 agus7 Ey TS <0) 3 YR ase} 2S 18 asuse ven —4 SS o _ apuse ' © S [3 12 ABS 6 & BR t le ABUSS 8H a > > ABUSS 13 r@ Is Is alin ie . ase 5 Asusa ev > asuss 2 alr *S¥ feo) Wo Fer REA RIE 2 ely i an te is A 83) & agusa ay agus3 rev—da ng r® 4 90 10, Ap2|!! ve z 2 ABUS2, 32N if: BD 5 ABUS2 BD Dec cntTR = nae ac ap ‘0 8 12 2 a sapa¢ op] | Ai B ABusi wy SH Asusi ABO 2 fa 13 z= a ABUSO By £ x Me ABUS® are vv eta] | ssv—2{_“ se ac ie oye 2 _ a ae 902 RESET —_e—___—_—“ares 7 fac) (Fe cera] pa? 2 4 fas o _paus7 ENDScREEN — (@ >» am pao 27 {al fp HZ peuse BRIS Ds. 0 espe FOL ol 1 pauss e RQ 2) bod 4 1D ry i DB4 = re) a 5S i Dausa D3 oat ae r@ 5 sav —la”*_a|8 rebate pea}22 Cs\ fp pauss oe pO pe | 5 oe |! ft —_4| fs Me pause
- o WWTACK pps 22 re fl 3 __paus: peg }33 ja) DBusé
owe
o x21 _alp, r® bs nb shtue ae
- iS wals4_ J) 20 ve ! MOODS . were Balw Bb2
A4 FOOTBALL
°
| °7 | or | ie |
1 po}! Tas EF oe ans a pepe
| Siro | ES. | RAMDe | +5v | +sv |
erze
| os a DE xeve | he | I |
uz | ne 90-1033| 90-1033
| ABUSIO | 5 | cs | |||||
| ABUS? | = | Ag | |||||
| ABUSE | a | aa | |||||
| ABUST | = | ar | |||||
| ABUSS | u | Ae | |||||
| Aguss | 7 | AS | |||||
| ABUS4 | x | Aa | |||||
| ABUS3, | + | iy | |||||
| BB | DI | ABUS2 | AQ | ||||
| NOTICE TO ALL PERSONS RECEIVING THIS DRAWING | bo] | _Ramp3 | ry | ||||
| Specific witten_ permsion ct Star ino, Sunnyate, | 3 | anos | i | ||||
| Eiforna’ This srawing t2 only conditional issued and | 01 | Yor | io | Agusé— | |||
| neither receipt nor possession thereo! conters or anster | ules 7 | Ol | RAMD2, | Pewee | |||
| any tt ino Heanae fo ao, thy sublet rater of he | WP? | She | amor | "hoa | yoo!!! | ramos | |
| awit or any design oc technical. information, sown | + | rH | iz | ||||
| thereon. nor any right fo reproduce this drawing or any part | 4 | gt XEVR oo|2 | _rampe | Ramps | —21 Joa | oa | RAMD2 |
| {erect except for manufacture by vendors of Ata Inco | Ro | RAMDS, | oz | vyou!® — amor |
rorated and for manufacture under the corporation's wr ;
| fen itcense, no right to reproduce this drawing ls granted | be | 2px | is | Rapa. | Wor | yo f+ | RAMDO |
| Orne subjoct matter there uniess by wntten agreement | mn | of! —ramoe | |||||
| sith or wetten permission tom the corporation | Ro | OF |
Ol VERSION -02 VERSION +O #
| +SU0 | tS | HBV | ay | HSV | SV | ast | Pe | hie |
| le | |e | Is | ls | Pia | 7A ial | a | ||
| wa | 33 | zs | ||||||
| KI | vl | HE | Fr | el | DI | PI | 7 NI | Ml |
038025 |033024|033023/033022 | 033021 | 033029] | 033028 | 038027 | ossoze
| ABUSIO | 8 | AID | 4Bvsio— | 10 | |||
| ABUSI | 1s | Ag | ABus9—2 | Ag | |||
| ABUSE | cs | Aa | Buss | —2 | as | ||
| ABUST | 7 | Cu | ABUS7 | u | AT | ||
| ABUSS | + | Ae | ABUSE: | 2 | Ae | ||
| ABUSS | 2 | AS | ABUSS. | 3 | AS | ||
| ABusd | 3 | Ag | agusa—4 | Ad | |||
| ABUS3 | 7% | a3 | ‘ABUS3 | 5 | a3 | ||
| Agus2 | Az | ABUS2 | £ | Az | |||
| ABUSI | £ | AL | ‘ABUSI | al | AL | ||
| ABusé | —* | Ab | ABUSS. | Ap. | |||
| pr | — | o4 | 04 | D3 | py | —1 | loz |
| De | a | 03 | o8 | H2__p2 | De | 4 | De |
| bs | 8 | 2 | ot | ray | os | 8 | bs |
| D4 | on | ol | ut | De | De | joe | |
| ce | ce | c | [ele | ps | Ke | ||
| to | | to |? | 10 |? | 10 |? | 10 |? | D2 | ry | bz |
| = | + | bi | 2 | D1 |
De: Dé
| cocoa | [esics2 | [esi ese. | |||
| PROGSELI | 2 | Row | ia he | reo | oye. |
> 2] I
avait =
| ‘PROTSELO | Pans | 8 | ‘ | i |
weap 932
FOR ALTERNATE CIRCUITRY TO -01,
| OrsEL | 2 | de | SEE SHEET 3 |
yo081 a mss—tho amy waroren qe S$ MICROPROCESSOR, MEMORY rem —4he Secooe ob2 na
Figure 1 Football PCB Schematic Diagram Sheet 2 of 6 030977-01, 02
FOOTBALL A5
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS AECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without Ihe Beatie, walen permission ot Alar inc.” sunnyvale,
ary right nor bjact matter of the Graulng oP ay" Ssign or technica. Information shown righ fo reproduce nls drawing or any par "or manulactore by vendors of Atari, Ineo ten ortne sub) ‘with or wet
| ere | a | BRI Le 7 | PR | PRI ae | arosy = | pada’ i | ares! = | pros’ |
| a | a | a | ee | a | i | a | a | aT |
| 42 | 32 | uz | Fe | Ka | 4 | na | ra |
go-to) | 90-703; | 90-7081 | 90-7031 | 90-703) | 90-7081 | 90-7031 | 90-7031 1; vea7 a
| PEAS | & | Ab |
| PEAS. | s | AS |
Prag —2t AG
| PFA | A | AR | |||
| PFAD | 2) | AZ | |||
| PFAL | 3 | FAY | |||
| PFAd | Ls | AG | |||
| DBUST | ‘3 | DI4 | bra | 7 | Devses |
| DBLUSe 3 | bia | ora | 13 | DBUSZ | |
| DBUSS. it | DIZ | Did | ee | DBUSI | |
| pevs4——4 | Beat | Dit | 2 | pause | |
| sestldgageleegag2/ | 28a / 88 saz | tese2 | assez] | seeaz |
B83e8 | SesaF | 28893 | B883F | Boaz | 288 a5 | RSE aS | Bee EE
| [ie [4 fiz fio feo we [14 [iz fio [20 [e [it fiz flo [20 fie fia fiz fio [Zo fie fd fiz io Jao | te fig [iz fio [20 | li4 fiz fio }20 fie [id [ie fio 120 | ||||||
| = 352 | g | af | wtag | B48 5 | co | s | 2 | © |
| agae | ag) | estes! | cane) | gaea!l | cance | oe | aves | |
| e28ae | ERGoe | Fbse | Booh— | FREE | ESESu | Beebe | Soa ke | |
| feese | eae | ebeele | Seebe | FREER | eesee | Seefe | Feber | |
| SEEGER | EFREE | EEPEG | GEEEE | EREEE | FEESE | Ebese | EEEER | |
| i | a | i | Ks | Ks | G | a | Ma | |
| ee | ee | ee |
apusio
| ee | Tt | t | T | t | t |
| a | CC | Ca | |||
| i | Ko |v | so | [om | [wo | |e: | re | ey | eo | 0 | oe |
ug esti | 05h dans o3Srnlanstas [aden] osstes|odstaajosstrs|oSifus|osater| obstea re ae a ae es a RS at at ne |, 34] Teed 33; ee
| 02 | 9 | DI |
| ol | & | De |
cen ‘Jee een _leez eee [eee id [? ft oP TP WE fo?
PLAYFIELD DISPLAY RAM
Figure 1 Football PCB Schematic Diagram Sheet 3 of 6 030977-01, 02
FOOTBALL A7
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbidden without the specilic witten permission of Alar, Inc.” Sunny Gafornia, This drawing 1s only conditionally issued, and neither receipt nor possassion thereat confers or transfers any right in, of license to use, the subject matter of the Grawing or any design or technical information shown thereon, norany ight to reproduce iis drawing or any part thereot except for manufacture by vendors of Atan incor porated and for manulacture under (ne corporation's writ. Ten license, no right to reproduce this drawing Is granted forthe subject matter there! unless by written agreement ‘with orwritien permission trom the corporation.
eMHE — Pot} os SCROLLGATE de
SCROLLGATE——} scaevis —Y Pre bro ° 2 a > oy 9
74 5 emnz —Hew 518 gre sy ud 22K ry a2
B30
RIB.
a
emnz —3] _y' ‘VaCANKe
4, HSYNC, Th vsync —8/02
an ae ac |S
aoe! L564 ae L®
‘oF
a] ‘on 3 SCRFVD le Jo fo |- fa
aw rehome c cK sit cr st RAWVID
12 ROT
250HeK
| &, 30 | DS | Goo | ||
| PICs | 14) | 03% | ry | GoDT |
| Pica | = | AT | GDL | |
| Pica | us | Ae | @Dde | |
| Pic? | 2 | AS. | Gd2 | |
| Pict | a | Aa ee | Gps |
4 25
| ore | — | aa ed | apa |
é
GAG: AD
oso Gde oh o2[tL eos gi cy) rare H 3-35 aoa ge | oa
Gd2 at
| GDS | GDe | 3 |
| G2 | GDI | 2 |
| GDI | GDI | | |
| ode | GDB | 5 |
2sene rseHee a ust wma Hea" a8 _zeonwe ere GRAPHICS, VIDEO OUT a
Sheet 4 of 6 030977-01, 02 VIDEO ouT
VIDEO RETURN
SCROLLGATE
Figure 1 Football PCB Schematic Diagram
FOOTBALL A9
45y
R52 1oK
vrei DR [iz RSS 1K
a
c2T [C40 BT
iJ 14x zZPL
edulis da = CK LD DIV
| zon [ie | Ap | ao? | |
| aI | 0 | be | © |
ENDSCREEN Tyo Sian ae
| SUaM [1 | + | 3 | gal |
| SELECTH [17 | t | * | 18) CNTR ald |
ce MIM RIP Ree Ror Roo es
10K 1OK PlOK
+5 —
AzTBL oR [Nf
H2TeI cK [13
PLIWP PLiVvD PL2ZND PLZVD
R39 +5V
rly 1 le 2 5 3 lA 4
= eo
tio 8 42 9 DECODER
A10 FOOTBALL DT
de bs.
Da
D3
dz
DL
de c
13 2 15| S ten sha gto [3 CK LD Dw us2ag
| a, 2 Be 7 | 8 | ie | |
| 10 | 6 | 6 | fi |
| usar 84 Fi | ‘4 | ic |
4s aB
| 1SlA cNTR gal? | 2 | 18 |
MM RIP 1626 12 is Teor We
ANODE B
fe] AMoDE
6] ANODE D Ja JP fo [*
is
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING P,R30 CONFIDENTIAL: Reproguction forbidden without the Specific written permission of ‘tan, Inc.” Sunnyvale, Gaifornia’ Tis aeawing is only cond! a eceipl nor possession thereat confers or transt iin, o license 10 uso, the subject alter ot ing oF any sesign or technical information sown
| Ss | ream. nor | any | roduce tis drawing oF |
74 ale {enilicanco, no right to toproduce the Grawing Is granted
| vTB2 CK | a | or the subject matter thereof unless by writen agreement |
cer ‘ttn or weltan’bermission irom tne corporation sa R30
il, se _ gf cee IS |,
| Ton | [s | + | Up | ap |
| = | 10 | Ho | & |
Test [is tsion ae)?
| SEcect ala} | + | 15], CNTR | _ |
MiMi ~The
| Res | SROs | Res | ; |
| 1OK | 10K | 1OoK |
+5V 7
+5V
P)R30 RSET CRS fon Sion bro 310 :
| eval | 13) | ir | 12 | 9 |
| H2TB2 piR[M | BS | D | Q |
22 pu [E0! 3
| W2T82 cK [I | EP >o£ | +sv |
a9 [ese a0 |
| Ot | q | 14x | ra, |
| 2eL | “ | ayy |
- 7 Db
| is} | —D- | [soe | |||
| __tedu ts g& = | go | Bg. | |||
| af CRP UG |G | a] | .s244 [iz | |||
| OPTION 4 | sD | HO | ap | 4 | D3 |
| OPTIONS + | Wt | sian ac}® | £ | ion | |
| oerion2 Fo | Na Syne a8|* | 4 | 1p | ||
| options | $1 | Bia CNTR gal3 | 2 | De | |
| M/A | RiP | 1G 2G |
as an Tee i
cen co INPUTS, OPTIONS, LED PINOUTS
LED Ci 33,20 1K ar od 2N3 043
R24 _ LED ca
Figure 1 Football PCB Schematic Diagram Sheet 5 of 6 i¢] eB eS 030977-01, 02
FOOTBALL A11
+su
RB
ait
KICKER, 6/5
cTRUD NTs fe lo Ta
WHISTLE
DBUSd
DBUSI
OBus2
DBYSs3 paus4 —4 ap 2a ___ coin cuter vevss—3/sp sq !2 RBS 330K
R30 be )\e& Ee
B37 LH¥>02— attract
+ 256H _- 8 P
cK
Fea 2Neose | c
AB aD Lsied. sus QE REG COW CNTR 3 l= le le nlp To
ag
OH Fq
KICKER —+
NOISE
B7 2 RNot
LSl64 sy at REG la Is T= Te Ie To
Al2 FOOTBALL
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction, tori any right in. or Sraig oF am
Rv “53 R14
47K Ol 41K cs wnistie R82 att
R73 ost AWA 4 SEES 8g 220K Oo} 249 Pp LM 324
+18N if u fa = 87 All +,,889 9] SPEAKER cee. a 4 TDA 1004 50k Volume apne
= Ba 2 [7 ye
co3 L__¢s3; a 1 Cet R72 001 ATTRACT wy lan —Les9 L WN3643 Tr200F = at
AUDIO
Figure 1 Football PCB Schematic Diagram Sheet 6 of 6 030977-01, 02
FOOTBALL A13
NMOHS
490718 NOILOA13S ADVLIOA AOL
ov
mS ETN Asoz Ao? LeLLey YaWHOASNVYL
«| G ;
| = | Ro | |p | lz | aS | | |
| zi; | S | els | 8 Ihw50 larecs)} |
OT erga #\8cz Cee
| 4 | ‘Fy Via | =m | ap | yar | iN |
| tA | Noe | fide | 5) | | | 2 |
| Lote | 4-135 | 84 | im) | [min | 58 |
| RRA | pl, | RD | 20 | ||
| 9 | Ris | 2 |
= | .
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL! Reproduction forbidden without the specitic writen. permission of Alari, Inc. Sunnyvale, ally issued, and ther receipt not possession thereat conters or vansfers, any right in, oF license to uso, the subject matter of the ‘estgn or technical information shown verean, nor any rig ice ts drawing or any part ‘thereot, except for manutacture by verdors of Atari, Incorporated and for manufacture under the corporation's wri fon liearse, no right to reproduce this drawing is granted Or the sublect matter thereof unless by written agreement v0 with or writen permission tom the corporation. 3 a wamod [c/->
Figure 2. Type B Power Supply Schematic Diagram 007197-01 Cc
Al4 FOOTBALL Lo-sss900V 80d
SLAM SWITCH ee Ane
LOCKOUT COIL BN
BN/8K
BKIV Bk 15 POS MOLEX y PLUG + MALE TERMINALS COIN SWITCH COUNTER #2
(RIGHT) (LEFT)
Ere ree ea COIN #2 conn BE peat teertncie
(LEFT) (RIGHT)
FRONT VIEW OF COIN DOOR
Figure 3 Coin Door Schematic Diagram 030401 R
FOOTBALL A15
44 POSITION EDGE CONNECTOR I@S5VCT_ GED il IeSVCT Ged A IOV _UNEES z IOV_UNEES rs WRCNDOe DISABLE S a
5 ; ZRepe & = Posse ANGDE 3 erat ANODE © FY ViDEO our TF VIDEO GRD HSS On COUNTER a pee LED Ce J e tence WEN, * +5V Ke Vre2 CK roy aT a SY /w Bu/w Y/BK GN/BK ss { BU/ Bie wi WR evi 7 =r W. TES! 15 Y COIN T S$ OR u leray VBR SPEAKER. Z wre TT t SrPeacer GED Bu 4 SPEAKER GED VES ZSVAC is ZBVAS wW. —— tt CBVAC 20 at 25VAC x te GRD ztet—y + [a15)} L GES
SPEAKERS
)
Al6 FOOTBALL J bldel gy Reg WEE RERM al ao|33|3 ¥ al z|u[ >| 5] > 210 1234567 q 128456789
TO CONTROL PANEL PLAYER @
ec TH BK, usv |!
| our | [2 | MONITOR | Last |
| FOR | POWER SUPPLY | 3 | {4 |
| SCHEMATIC SEE OO7197-O1 | vo | ft |
Tw WIENIoE 95 68 ol! '
| sp | eee | power | bk | Boe | ool | ae EN ocuRE | | |
| Z| | De | zl | swren |} 3) | CdECdEtti<is«é~«~iSd;i‘Y GB WX | 9 ™—"._ sss | BROT |
| a3] | Ses | ER | S| | ox | wW | & |
| yl | asi | Ww. | ||||
| 2.5amP | of | 2 |
SLO BLO
Buren (7 (‘= t uz BK | 3, BS Tene] 3 RIGN| 5 bo
030401 {on-OFF lon ey
FOR COIN DOOR,
SCHEMATIC SEE PLAYER Lb
con DOOR
ae)
PLAYER 2
SERVICE PNL- TOP VIEW OF CABINET
oe BK 2} vy 7 sS/eig bg LI [2121313 oo 2sf5o7] 1234567
| | | CONTROL PANEL- PLAYER LO | | | isha Sosk>: | |||||
| oN | 2 | 1 | —6) | |||||
| 4 | ' | HORIZONTAL, | |] | |||||
| \ | 1 | 357i | : | DOWN | ||||
| | | 2, 94° | lex | H | OUT | BOMB | SNEAK SWEEP | ||
| | | oy! | fof | 2 | } | + | + | + | + |
| an (pen | { | a | ae | 4) | ||||
| wen | of wen | 1 |
jae : BK Ty '
| Boise |e\efea | VERTICAL | H | |
| ev/BK |e | | elev] | j | I |
| ETM | 7 | ° | \ |
| wi | _/g/a} wt | 6 | 5 |
BK (5 |o[2< 7 1 fl fl
i '
' ' ! I!
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction” forbidden without the specific willen permission of Atari, Inc, Sunnyvale, California. This drawing is only conditionally issued, and helther receipt nor possession thereat confers or transfers any right In, oF Hicense to use, the subject matter of the Grawing or ‘any design or technical information stiown thereon, nor any right to reproduce this drawing or any part ‘except for manulacture by vendors of Alar, porated and for manufacture under the corporat
| 10 right to | reproduce this | drawing is granted |
sol matter thereot uniess by wri
Figure 4 Football Game Harness Schematic Diagram 033322-01
FOOTBALL A17
CONTROLS
DISPLAY MAIN PCB PCB
EF} speanen
MONITOR
| INTERLOCK fon SWITCH 1 voLUME CONTROL AND SELF-TEST SWITCH
'A033323-02 (Ref) HARNESS AND SWITCH ASSEMBLY POWER
FUSE 2.5 AMP SUPPLY
SLO-BLO
INTERLOCK SWITCH
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction, lepidden. without the
5 pr drawing or an thereat excop! for manufacture by vendare of Alar, porated and for mantfacture under ine corporation's wr ten license, no night te reproduce this drawing 's granted forthe subject matter thereot Unless by written agreement ‘gith or written permission trom the corporation,
Figure 5 Football Game Harness Layout A033580-01 A
A18 FOOTBALL
APPENDIX B
Atari Customer Service Information
If reading through this manual does not lead to solving a specific maintenance problem, you can call Tele-Help™ at the following two Atari Customer Service offices.
WEST and CENTRAL U.S.A.
Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time)
From California, Alaska or Hawaii, dial (408) 745-2900
From anywhere else in this area, dial toll-free (800) 538-1611
EAST U.S.A.
Atari Inc. New Jersey Customer Service Office 44 Colonial Drive, Piscataway, NJ 08854 Telex 37-9347 (Monday - Friday, 8:30 - 5:00 pm Eastern time)
From New Jersey dial (201) 981-0490
From anywhere else in this area, dial toll-free (800) 631-5374
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
lithe products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
Punic ; In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR-
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
ATARI
ATARI INC. 1265 BORREGAS AVENUE PO. BOX 9027 SUNNYVALE, CALIFORNIA 94086. 408/745-2000 TELEX 35-7488 QA Warne: communications Conesny