Joust Instruction Manual (16P-3006-101 Rev A) Dec 1982
Joust (Green label) (Williams, 1982) · Instruction Manual · 14 pages · 29 sections · original scan
16P-3006-101 Hilliaoms Y _EMSION
INSTRUCTION MANUAL
FOR
UPRIGHT GAMES
Including procedures for...
¢ Operation
¢ Auditing ¢ Adjustment
¢ Diagnostics
‘or service... J 4
NOTE NEW TOLL-FREE
TELEPHONE NUMBERS: Williams
ELECTR ~ arr 800-621-1253 s4or N. Califo baat IL 60618 In itliry Cable Address: WILCOIN, CHICAGO 800-572. So4 (312) 267-2240
No 16-3006-101-AMT-1 October 1982
MANUAL AMENDMENT
MANUAL AFFECTED: 16P-3006-101 and 16P-3006-101 T Keep This Sheet With Your Instruction Manual
PURPOSE: To Update JOUST ROM Summary
ROM
JOUST 1B
JOUST 2B
JOUST 3B
JOUST 4B
JOUST 5B
JOUST 6B
JOUST 7B
JOUST 8B
JOUST 9B
JOUST 10B
JOUST 11B
JOUST 12B
Decoder ROM 4 (Horizontal)
Decoder ROM 6 (Vertical)
Video Sound ROM 4
Special Chip 1
NOTES:
Current JOUST games use green-label ROMs. PART NO.
A-5343-09961-A
A-5343-09962-B
A-5343-09963-B
A-5343-09964-B
A-5343-09965-B
A-5343-09966-B
A-5343-10150-B
A-5343-09968-B
A-5343-09969-B
A-5343-10153-B
A-5343-09971-B
A-5343-09972-B
A-5342-09694
A-5342-09821
A-5343-09973
A-5410-09911 DESCRIPTION
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 4Kx8, G!
PROM, 512x8
PROM, 512x8
ROM, 4Kx8
Special Chip
REEN LABEL
REEN LABEL
REEN LABEL
REEN LABEL
REEN LABEL
REEN LABEL
REEN LABEL
REEN LABEL
REEN LABEL
REEN LABEL
REEN LABEL
REEN LABEL
Earlier games have either yellow or red-label ROMs, which are interchangeable and may be mixed in the same game. DO NOT attempt to mix green-label ROMs with red or yellowlabel ROMs.
Boards with green-label ROMs should include jumpers W1 and W3 only. Boards with red or yellow-label ROMs
Williams Wy) substitute jumpers W2 and W4.
E 3401 LECTRONICS, INC. N. California Av. Chicago, IL 60618
ROM SUMMARY
| ROM | PART NO. | DESCRIPTION |
| JOUST 1A | A-5343-09961-A | = PROM, 4Kx8, YELLOW LABEL |
| JOUST 2A | A-5343-09962-A | PROM, 4Kx8, YELLOW LABEL |
| JOUST 3A | A-5343-09963-A | = PROM, 4Kx8, YELLOW LABEL |
| JOUST 4A | A-5343-09964-A | = PROM, 4Kx8, YELLOW LABEL |
| JOUST 5A | A-5343-09965-A | = PROM, 4Kx8, YELLOW LABEL |
| JOUST 6A | A-5343-09966-A | PROM, 4Kx8, YELLOW LABEL |
| JOUST 7A | A-5343-09967-A | | PROM, 4Kx8, YELLOW LABEL |
| JOUST 8A | A-5343-09968-A | = PROM, 4Kx8, YELLOW LABEL |
| JOUST 9A | A-5343-09969-A | = PROM, 4Kx8, YELLOW LABEL |
| JOUST 10A | A-5343-09970-A | = PROM, 4Kx8, YELLOW LABEL |
| JOUST 11A | A-5343-09971-A | = PROM, 4Kx8, YELLOW LABEL |
| JOUST 12A | A-5343-09972-A | = PROM, 4Kx8, YELLOW LABEL |
| Decoder ROM 4 | A-5342-09694 | PROM, 512x8 |
(Horizontal)
| Decoder ROM 6 | A-5342-09821 | PROM, 512x8 |
(Vertical)
| Video Sound ROM4 | ~—A-5343-09973 | ROM, 4Kx8 |
Special Chip 1 A-5410-09911 Special Chip
POWER TURN-ON
WHEN THE GAME IS FIRST TURNED ON it produces a sound. Simultaneously general illumination should come on and a moment later a scanning “rug pattern”' indicating the RAM test should appear on the screen. Next the rug should become stationary as the ROM test is performed. In a correctly running game the rug pattern will be followed by the message "INITIAL CHECKS INDICATE ALL SYSTEMS GO". If RAM or ROM failure messages come up on the screen instead, refer to Power-Up Tests in TROUBLESHOOTING PROCEDURES.
GAME OPERATION
GAME START - Insert coins; a random sound is produced and credits are displayed on the CRT. With two or more credits displayed, pressing 2-player start initiates a 2-player game where each player gets five* mounts (turns).
*Adjustable Feature
PLAYER CONTROLS
The Joystick sends the gladiator and his ever stalwart mount (ostrich or stork) boldly to the left or to the right.
The Flap Button causes the hero’s mount to spread its robust wings.
GAME PLAY
AT SOME FAR-DISTANT TIME two fantastic gladiators meet and square off for battle. Each is mounted on a fanciful bird of prey (ostrich or stork) who’s wings can carry it from the cliftops to the mouth of the abyss and hopefully back . . . or the bubbling lava below will increase it’s toll.
While your mount is a skilled flyer, your opponent is a shrewd gladiator. You must prove you are his better. Stealthily you must pilot your mount above him, and cleverly you must stalk him . . . to strike at the moment he least suspects you! And always remember this rule: In every Joust, the highest lance wins!
Of course your opponent will resist your attempts, all the while pursuing his own designs on you. Each gladiator has five* mounts. Every time you’re toppled you must mount a new bird for the next joust. The gladiator who scores the most dismountings is the winner.
YOUR PATH MAY SEEM CLEAR and your work cut out, but just them a flock of vicious Buzzard-Riders will ambush you! Ruthless even as they are dismounted, these wily Buzzard-Riders instantly lay their eggs. You must pick up the eggs or they will soon hatch into even more persistent and antagonistic foes!
Fortunately at 20,000* points (should you make the grade) you will be awarded another bird to mount against the loyal opposition.
Joust is designed for either one or two players.
HIGH SCORE SIGNATURE
Select letters with the joystick. Push right to move forward through the alphabet; push left to move backward. Then push the FLAP button to lock in the letter.
BOOKKEEPING AND EVALUATION TOTALS
- In Game-Over Mode, open the cashbox and depress the cashbox advance switch. The advance switch located on the coin door can also be used. The CRT should indicate all bookkeeping and evaluation totals. If so, go to step 3. If the CRT display comes up in the ROM test, perform step 2.
AUTO-UP
HIGH MANUAL ADVANCE SCORE DOWN RESET
Figure 1. Coin Door Button Switches
- Continue to depress the cashbox advance switch, stepping the game through test programs for ROMs, RAMs, CMOS RAMs, color RAMs, sounds, switches, and then CRT test patterns, of which there are five. The fifth test pattern, color bars, directly precedes the CRT display of the bookkeeping and evaluation totals.
3, The bookkeeping and evaluation totals appear on the displays as in Figure 2.
- Adjustable feature
CLEARING BOOKKEKPING TOTALS
Depress ADVANCE to display Game Adjustments. Operate PLAYER 1 joystick to position cursor on CLEAR BOOKKEEPING TOTALS. Push PLAYER 2 Joystick. Depress ADVANCE. (aaa
BOOKKEEPING TOTALS
LEFT SLOT COINS 167 CENTER SLOT COINS 0 RIGHT SLOT COINS 426 PAID CREDITS 593 FREE MEN 221 TOTAL TIME IN MINUTES 1038 TOTAL MEN PLAYED 2000 TOTAL SINGLE PLAYER 101 TOTAL DUAL PLAYER 492 TOTAL CREDITS PLAYED 593 AVERAGE TIME PER CREDIT 1:45
Figure 2. Bookkeeping display
GAME ADJUSTMENTS
In the Game-Over Mode open the coin door with AUTO-UP/MANUAL-DOWN switch set to AUTO-UP, and depress the coin door ADVANCE switch twice to cause a CRT display as shown in Figure 3.
To select and then set functions to the desired values, use the PLAYER | joystick (push right to move arrow down, left to move arrow up) then, making sure the coin door is open, use the PLAYER 2 joystick to increase or reduce the value of the selected function.
The number of turns (men) per |-credit game can be set anywhere from | to 99 (5 recommended). Difficulty is factoryprogrammed at 5 (moderate). It can be custom-programmed (0-9, with 9 conservative) as desired.
Game pricing is selected with standard set ngs or with custom settings as shown in Tables | & 2. Table | lists some common pricing schemes and dit the ler to the proper entry in Table 2, which sho’ ‘hat the CRT display should look like to accomplish the desired pricing. Note that free play can be elected by entering the code number 9 at the PRICING SELECTION function (see Tables | and 2).
For standard settings you need change only the PRICING SELECTION. For custom settings, first set PRICING SELECTION to zero and then set the remaining values according to Table 2.
GAME ADJUSTMENT
EXTRA MAN EVERY MEN FOR 1 CREDIT GAME HIGH SCORE TO DATE ALLOWED PRICING SELECTION 3 LEFT SLOT UNITS CENTER SLOT UNITS RIGHT SLOT UNITS UNITS REQUIRED FOR CREDIT UNITS REQUIRED FOR BONUS CREDIT MINIMUM UNITS FOR ANY CREDIT FANCY ATTRACT MODE DIFFICULTY OF PLAY LETTERS FOR HIGH SCORE NAME RESTORE FACTORY SETTINGS CLEAR BOOKKEEPING TOTALS HIGH SCORE TABLE RESET AUTO CYCLE SET ATTRACT MODE MESSAGE SET HIGH SCORE NAME NO NO NO NO NO NO 20000
YES 1/QUARTER 4/DOLLAR
USE ‘PLAYER 1 MOVE’ TO SELECT ADJUSTMENT USE ‘PLAYER 2 MOVE’ TO CHANGE THE VALUE PRESS ADVANCE TO EXIT
Figure 3
Highest Score Signature . Game Adjustment
The number of letters allowed the highest scoring player for entering his name can be varied from 3 to 20 and is recommended as 3. If objectionable words are entered as the signature name, you can change the lettered entry leaving the highest score the same. See Setting Highest Score Name.
Restore Factory Settings
- Position the cursor on RESTORE FACTORY SETTINGS.
- Push PLAYER 2 joystick to the right. 3 Depress ADVANCE switch twice.
Resetting High Score Table
- Position the cursor on RESET HIGH SCORE TABLE.
- Push PLAYER 2 joystick to the right. 3 Depress ADVANCE.
Setting Attract Mode Message
Position the cursor on SET ATTRACT MODE MESSAGE. Push PLAYER 2 joystick to the right. Depress ADVANCE. Enter up to two lines of your message following instructions on the screen Depress ADVANCE to terminate process. FEN S
Setting High Score Name 1 Position the cursor on SET HIGHEST SCORE NAME.
- Push PLAYER 2 joystick to the right. 3 Depress ADVANCE.
- Enter new signature; depress ADVANCE to terminate process.
Table 1. Pricing Schemes
2/50¢, 4/$1 1/50¢, 3/$1, 4/$1.25 1/50¢, 3/$1, 7/$2 1/50¢, 3/$1, 6/$2 TABLE 2 SreuAciaa CREDITS/MONEY STANDARD SELECTION/ CUSTOM KEY Twin Quarter 1/25¢, 5/$1 Quarter, Dollar, Quarter 2/50¢, 5/$1 1/25¢, 4/$1 A B
Cc D E
1/50¢ 5
| 1DM, SDM | 1/1DM, 6/5DM | 2 |
| 20-Cent, 50-Cent | 1/20¢, 3/50¢ | F |
| 1 Franc, 5 Franc | 1/2F, 3/5F | 4 |
| 25 Cent | 1/25¢, 4/1G | 6 |
| 1 Guilder | 1/25¢, 5/1G | G |
| 5 Franc | 1/SF, 2/10F | 7 |
| 10 Franc | 1/10F | 8 |
| 1 Franc, 2 France | 2/1F 5/2F | 2 |
| 100 Lire, 200 Lire | 1/200 Lire | 8 |
| Twin Coin | 1/1 Coin | 3 |
1/2 Coins 5 1/3 Coins, 2 5 Coins H
| 1 Unit, 5 Unit | 1/2, 3/5 | 4 |
1/1, 5/5 I 1/3, 2/5 J
| FREE PLAY | : | 9 |
Table 2. Pricing Settings
DISPLAY CUSTOM KEY FUNCTIONS STANDARD/SELECTION A/|BIC{D{E|F/G/H/I|J
| Pricing Selection | 1 | 2/3)4)]5)6/7;)/8/9/0]0)0;/0);0],0]0]/0);0),0 | |||||||||||||||||
| Left Slot Units | 1 | 6 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 3 | .}12) | 6) | 1 | 2 | 1 | 2 |
| Center Slot Units | 4}/0]4)16}4)/0/0)0/4/]/4)]4)4 | /12/48}0]0;]/0),0)0 | |||||||||||||||||
| Right Slot Units | 1 | 1 | 1} | 6})1)4]/2)2 | 1 | 1 | 1 | 1 | 3 | 12) | 15) | 4 | 2] | 5 | 10 | |||||||
| Units per Credit | 2 | 1 | 1; | 2)2 | 1 | 1 | 2 | 1 | 1 | 1 | 1} | 4/14) | 5 | 1 | 5 | 1 | 5 |
Units for Bonus Credit 4}/0;}0)/0]0;)0/0;]0/0/4)]4)]0/]15)96}0}]4]0)0)0 Minimum Units forCredit | 0 | 0 | 0|0/O{[0]0/0}]0}{]0/2/2]0/24/0|0/]0/0/0
TROUBLESHOOTING PROCEDURES Certain types of game malfunctions may inhibit the game's diagnostic or display faculties. Troubleshooting procedures for most of these types of malfunctions as well as malfunctions that permit self-diagnosis are covered below. Our troubleshooting algorithm begins with Power-Up and continues until Game Over Mode. All procedures can be performed with minimal test equipment or merely by observing the game itself. POWER-UP TESTS NO GENERAL ILLUMINATION NO INITIAL VIDEO (RUG PATTERN) CHECKING POWER SUPPLY BOARD
- Check fuse F2 on power supply board.
- Check for proper installation of jumpers W1, W2, W3 and/or resistor R27. (Some machines DO NOT have an R27. Refer to your drawing set.)
- Check 4P1/J I, 4P3/J3, 6P2/J2 and 6P3/J3.
- If all the above don't turn up the problem check power supply board.
- Open back doors
- Press reset button on CPU Board.
- Try RAM and ROM tests (see below).
- If all the above don't turn up the problem, check power supply board.
- Swap power supply board with one from known-good game.
- If game plays, problem is on power supply board.
- If game doesn't play, check power transformer with voltmeter.
- If known-good power supply is unavailable for tests above, check +5V,—5V and + 12V outputs on power supply in game. Each MUST BE within 2% of rated output with less than 0.1% AC hum. MORE POWER-UP TESTS ROM BOARD | ROM BOARD _— LEDs LEDs 7 -
TEST RECOGNIZE IDENTIFY VIDEO REMEDS
CONDITION CHIPS
| GENERAL | | “0” meansall | - | (1) Scanning rug pattern | If any video (see left) is missing or |
| power-up tests | (2) Stationary rug pattern | error message is displayed, proceed | |
| passed | (3) "INITIAL CHECKS INDICATE ALL. | to Diagnostic Mode tests. |
SYSTEMS GO"
- Game-Over Mode
| CMOS | “0” means tests | - | “HIGH SCORE TABLE RESET” | (1) Open coin door and turn power |
| (See | passed | “BOOKKEEPING TOTALS CLEARED” | off and on. |
Appendix A) “ADJUSTMENT FAILURE” “RESTORE FACTORY SEITINGS BY OPENING FRONT DOOR OR TABLETOP AND TURNING GAME
| 0” means tests | - | “FACTORY SEITINGS RESTORED” | (2) Press ADVANCE. Game should |
passed return to Game-Over Mode.
| BATTERY | “0” means tests | - | “HIGH SCORE TABLE RESET” | (1) Open coin door and turn power |
| (See | passed | “BOOKKEEPING TOTALS CLEARED” | off and on. Or press ADVANCE. | |
| Appendix A) | “ADJUSTMENT FAILURI | In either case, game should return |
“RESTORE FACTORY SEITINGS BY to Game-Over Mode. OPENING FRONT DOOR OR (2) Check AA alkaline cells on TABLETOP AND TURNING GAME CPU Board. OFF AND ON” (3) If problem persists proceed with CMOS RAM test by putting the game into its Diagnostic Mode (see SELF-DIAGNOSTICS).
| MEMORY | “0” means tests | - | “HIGH SCORE TABLE RESET” | (1) Making and breaking coin door |
| PROTECT | passed | “BOOKKEEPING TOTALS CLEARED” | interlock switch, check with VOM |
| INTERLOCK | “ADJUSTMENT FAILURE” | and replace if faulty. | |
| (See | “RESTORE FACTORY SEITINGS BY | (2) Replace if faulty: Memory | |
| Appendix A) | OPENING FRONT DOOR OR | protect gates 6E, IC1, QI, or CMOS. |
TABLETOP AND TURNING GAME RAM IC. OFF AND ON”
| SPECIAL | “0” means tests | - | (1) Scanning rug pattern. | (D Turn power off. |
| CHIP | passed | (2) Blank screen instead of “INITIAL | (2) To find bad chip replace 2 |
TESTS INDICATE: OPERATIONAL” special chips one at a time with
- High score table with no scores. known good chips.
- Intro blank or program crash. (3) Turn Machine on after each replacement and run through Power-Up Tests.
+5v DC ADJUSTMENT (R10 & R24)
Before adjusting the voltage output, always check the output at the supply for AC hum. This hum should never rise above 0.005v on the +5v DC supply. If it does, consult your schematic drawing set for proper DC voltages throughout the circuit. Test for these with the DC setting of your multimeter. Make a second check using the AC setting. Pay particular attention to readings at TP5 (top of capacitor C10). If the voltage here is too low (less than +11v DC) or you find excessive ripple (more than 700mv rms), replace the capacitor.
Table 3 Voltage Adjustments to +5v De Supply
| WHICH RESISTORS | Neither | R10 only | R24 Only | R24 &R10 |
SUPPLY HAS...
| TO INCREASE VOLTAGE | Add R24 | Remove R10 or | - | Remove R10 or |
| IF UNDER 4.25v DC... | add R24 | add R24 | |
| TO DECREASE VOLTAGE | Add R10 | - | Remove R24 or | Remove R24 or | |
| IF OVER 5.25v DC... | add R10 | add R10 |
SELF DIAGNOSTICS
If RAM or ROM failure messages are displayed on the CRT after the “rug pattern” proceed with self-diagnostics. Selfdiagnostic procedures are controlled by the AUTO-UP/MANUAL-DOWN and ADVANCE switches in the coin door. Set the AUTO-UP/MANUAL-DOWN switch to the MANUAL-DOWN position and depress the ADVANCE pushbutton. The game is now in its Diagnostic Mode and a ROM test is performed. With ROM test results present on the CRT display, depressing the ADVANCE pushbutton initiates the RAM test. Further tests (CMOS, sound, switch, color RAM, monitor test patterns) are encountered one after the other as the ADVANCE pushbutton is depressed (once more for each subsequent test).
MONITOR TEST PATTERNS - For ease in monitor adjustments, the monitor may be slid back and the screen viewed in the CRT mirror provided on the inside-top of the cabinet. Remove the two bolts and carefully slide the monitor back in its shelf; secure the monitor in the extended position by inserting the two bolts though holes in the monitor base and monitor shelf provided at the left side of the monitor. AUTO CYCLE MODE - From the color bar pattern (or Game Over with the switch set to AUTO-UP) depress ADVANCE two times to display GAME ADJUSTMENTS.
- Position the cursor on AUTO CYCLE with the MOVE Joystick and push the FIRE joystick up. e Depress ADVANCE.
- The system will now sequence through ROM, RAM, and CMOS RAM tests repeatedly. The coin door must be open during the Auto Cycle test. If an error is detected, the test is terminated and the failure indication is displayed on the CRT.
- To terminate the Auto-Cycle test, turn the game OFF and ON.
is ~ FISIGIEIEIEIEIE
~ BEBREEED
~ BSSEEEEE
Figure 4. RAM Location and Numbering on the CPU Board
DIAGNOSTIC MODE RAM AND ROM TESTS esr | LED. | ,ROMBOARD se
TEST RECOGNIZE en VIDEO REMEDY
CONDITION
| ROM | “2” means ROM | 2-digit ROM chip | “ROM ERROR” and ROM _| (1) Turn power off. | |
| error. | number | chip number. | (2) Replace suspected chip. |
| RAM | “1” means RAM _$ | Bank number first, | “RAM ERROR” followed | (1) Check for normal voltages on |
| error. | then chip number in| | by RAM bank number and _| indicated RAM chip: -Sv/pin 1, |
bank (see figure 3) | chip number (Note: with +12v/pin 8, +5v/pin 9. multiple RAM failures this (2) Turn power off. display may not appear) (3) Replace suspected chip.
- With multiple RAM failures always check power supply. See POWER-UP TESTS.
| CMOS | “3” means | 7 | “CMOS RAM ERROR OR __| (1) Check pin 22 of CMOS RAM for |
| (See | CMOS RAM | WRITE PROTECT | +3.2VDC minimum. If present, |
| Appendix A) | error | FAILURE” | replace CMOS chip IC. If absent |
replace AA alkaline cells.
- With new alkaline cells, check for +3.8VDC. If still absent, replace diodes D9 and D10.
- Upon power-up and re-entry into diagnostics if CMOS error message persists check CMOS RAM memory protect and address decoding circuits with a logic probe.
Tests 4 and 7 provide sequential subtests. To stop automatic cycling set switch to MANUAL-DOWN. Depress advance in MANUAL-DOWN to step through subtests. LED indications are not made for these tests.
TEST & PROCEDURES VIDEO REMEDY OR ADJUSTMENT
| SOUND | “SOUND LINE 1” | Missin; | Check |
| (Test 4) | “SOUND LINE 2” | 1 | 2P4/1OP3 Pin 3 |
| “SOUND LINE 3” | 2 | 2P4/10P3 Pin 2 | |
| “SOUND LINE 4” | 3 | 2P4/10P3 Pin 5 | |
| “SOUND LINE 5” | 4 | 2P4/10P3 Pin 4 | |
| “SOUND LINE 6” | 5 | 2P4/10P3 Pin 7 | |
| (These appear one at a time) | 6 | 2P4/10P3 Pin 6 |
All Perform Sound Board
Diagnostics (see below) SWITCH TEST CRT indicates AUTO-UP closed and any stuck | (1) COIN DOOR SWITCH STUCK:
| (Test 5) | switches. CRT Display | for Each Switch ... | Disconnect 2P3 |
- Set switch to MANUAL- DOWN and clear any stuck switches.
- CRT should indicate no switches closed.
- Operate switches and check for display of switch name. Coin Door Player Panel
ADVANCE 1- PLAYER START AUTO-UP 2- PLAYER START HIGH SCORE RESET MOVE 1 LEFT COIN FLAP 1 CENTRE COIN MOVE 2 RIGHT COIN' FLAP 2 SLAM SWITCH
- PLAYER PANEL SWITCH STUCK: Disconnect 3P2 or 3P3
- COIN DOOR SWITCH DOES NOT OPERATE: Ground corresponding pin of 2P3.
- PLAYER PANEL SWITCH DOES NOT OPERATE: Ground corresponding pin of 3P2 or 3P3
SYMPTOM REMAINS SAME... ROM Board or Interface Board Faulty. SYMPTOM CLEARS UP... Problem is in switches or wiring
MORE DIAGNOSTIC MODE TESTS
TEST & PROCEDURES VIDEO SEQUENCES REMEDY OR ADJUSTMENT
COLOUR RAM TEST (Test 6)
- CRT sequences through 8 colors, 2 seconds each
- Thick vertical band indicates color RAM fault. 1 Light red screen 2 Red screen 3 Dark red screen RAM 1B RAM 2B Too-light or Magenta band too dark red or gray band 4 Light green screen | Yellow band Cyan band 5 Green screen 6 Dark green screen 7 Light blue screen Magenta band Too-light or too 8 Blue screen dark blue or gray band 4 Light green screen Green band Dark green band or gray band 5 Green screen Light green band Dark green band or gray band 6 Dark green screen : Grey band MONITOR & COLOUR RAM TEST (Test 7)
8=MAGENTA Color Bar Pattern Cross hatch pattern Aids you in setting up vertical and horizontal linearity, convergence and focus.
Red screen Green screen Blue screen Color Bars Aids you in optimizing color purity
Color Bars
- Double-width ° Half-width ° Transposed If color RAM test 6 indicates no faults, symptoms at left suggest a fault in 1A, 1B, 2B or 2C chips.
SOUND BOARD DIAGNOSTICS SYMPTOM TEST AND PROCEDURES
MISSING SOUNDS 0 CHECK SOUND SELECT INPUTS NO SOUND (1) Turn power on.
- Depress DIAGNOSTIC pushbutton on bottom of soundboard. Sounds may be produced now even though absent in diagnostic mode 4. If you hear game sounds proceed with this checkbox. If not go ahead to POWER SUPPLY checkbox below. TEST TOOL ‘CONDTION AND REMEDY. ‘Sound board connector 10P3I3- | Logic Probe (Game on and in | * PULSING - Proceed,
| 1t06 | test 4) | + LOW - check jacks, foils. |
+_STILL LOW - Perform ROM board checkbox below. ‘SRI DIP resistors R3 to RO VOM - Reading ohms (game | * ALL 4.7K - Proceed off) +_ANY OPEN - replace SR1. C310 C9 VOM - Reading ohms (game | * ALL OK - Proceed. off) +_ANY SHORTED - replace bad.
| IC5-1 | Logic Probe (Game on andin | * | HIGH - Proceed. | |
| IC7-14 | test 4) | * | LOW - Replace C19 (ICS) or C21 (IC7) |
+ STILL LOW - Replace bad IC.
| 1C5-2, 4, 6, 10, 12, 15 | Logic Probe (Game on andin | * | PULSING - Proceed. |
| IC7-4.6 | test 4) | + LOW - Replace bad chip. |
IC10-18, 19 Logic Probe (Game on andin | * PULSING - Proceed.
| (PIA) | test 4) | + LIFT C20 - Retest. |
+ PULSING NOW - Replace C20. + STILL LOW - Replace 1C6, retest.
| IC10-10 to 17 | Logic Probe (Game on andin | * | PULSING - Proceed. |
test 4) + SOME LOW Replace IC.
- ALL LOW- Lift C31, retest + PULSING NOW - Replace C31 + STILL LOW - Replace IC SOUND WHEN 1 CHECK ROM BOARD OUTPUTS DIAGNOSTIC (J) If you hear game sounds, disconnect and reconnect sound board connector 10P313. PUSHBUTTON PRESSED BUT NOT IN DIAGNOSTIC
- You Should hear one or more game sounds. If so put the game in DIAGNOSTIC MODE Test 4 and proceed with this checkbox. If not go ahead to POWER SUPPLY checkbox below. MODE TEST 4 TEST TOOL CONDTION AND REMEDY ROM board connector 2P414-3_ | Logic Probe (Game on and in | + PULSING - Repair cable to sound board.
| 106 | test 4) | +_ANY LOW - Replace jack or foil, proceed. |
OC DIP resistors 2 to 6 VOM - Reading ohms (game | * ALL 4.7K - Proceed off) +_ANY OPEN - replace 0C. €26-39 VOM - Reading ohms (game | * ALL OK - Proceed. off) +_ANY SHORTED - replace bad.
| IC10-10 to 15 | Logic Probe (Game on andin | * | PULSING - Proceed. |
| (PIA) | test 4) | + SOME LOW Replace IC. |
- ALL LOW- Lift C23, retest + PULSING NOW - Replace C23. + STILL LOW - Replace IC NO SOUND 1 CHECK ON-BOARD POWER SUPPLY (J) With power off test for fuse continuity at Fl and F2.
- With power on check for +12v unregulated DC at TP1 and pin 5 of IC1.
- Now check for +5v regulated DC between TP4 and TP3. If voltages are absent or low turn off game and lift one pin of filter capacitors C25, C26 and C27.
- Check each with ohmmeter for possible short circuits.
- If capacitors are good and unregulated voltages test okay but you're missing +5v, replace regulator chip IC8. ‘STILL NO SOUND CHECK AUDIO (ANALOUGUE) SECTION
- Turn power on; turn up volume control. Momentarily place powered-up AC soldering pencil on final amplifiers input pin (ICI, pin 1 or 10P4, pin 2) If you hear low hum, audio IC, volume pot and speaker are okay.
- Repeat test at Q2 emitter. If you hear hum, analogue section is okay. Step (1) will also work if you simply touch amplifiers input pin. However output level of hum will be much lower than with soldering iron. DO NOT use a soldering pencil over 40 watts. Cordless models will NOT work here, MISSING SOUNDS: 1 CHECK SOUND ROM 12 AND RELATED CIRCUITRY NO SOUND (4) Is jumper W1 connected? IT SHOULD BE on all JOUST games, or sound signals from the D/A converter (IC13) will never arrive at input of impedance-matching transistor Q2.
- Turn power on.
- If you have no game sounds but power supply tests show normal voltages and no ripple on +5v, check crystal clock circuit. Using DVM or logic probe, test for pulsing AC across crystal. If clock signal’s absent replace crystal and associated capacitors.
- Turn off power.
- Swap sound ROM (IC12) and microprocessor chip (IC9) with known-good chips.
- Power up and test Sound Board after each swap by pushing DIAGNOSTIC button.
APPENDIX A
CMOS RAM Data Test Protocol POWER ON The first sub-test of the CMOS RAM data is that of the ATTRACT MODE 1 ——<— MESSAGE checksum. If the test a does not pass, the factory ATTRACT ‘ATTRACT MODE ‘MESSAGE? PASS
| MODE | MESSAGE | is | restored. |
Next, the game adjustments are ¥ PAL
| checked and | restored | to factory | RESTORE |
settings if an error is found. If game pagreRy adjustments are found intact, the high score table is checked for any bad entries. Bad entries are replaced with PASS a score of 4,000 points and no “ADIUSIMENTS?, initials. If all entries check, the game returns to the Game Over Mode. y PAE GAME
RESTORE
| If game adjustments are restored to | cerake | HIGH | PASS |
A 3 < SCORE —
| factory | settings, | the © AUDIT | —__,—__ | ENTRIES? |
TOTALS are checked. If 5 or more FAIL
| audit digits are other than 0-9 (that is | AUDITS? | a | BAD ENTRIES |
hexadecimal A through F) all audit Oe
| totals are cleared. This is followed | 4 | SOR MORE MEX AF | INITIALS |
by a check of the high score table and curar
| the table is reset to factory settings if | AUDITS | “INITIAL TESTS, |
: INDICATE ALL
| errors are found. | Finally, game | SYSTEUS 6G" | |
| adjustments are rechecked and either | J | DISPLAYED | |
| OPEN COIN DOOR or FACTORY | ‘aa | pass | |
| SETTINGS | RESTORED | is | SCORE |
displayed. With the former, open the coin door and turn the game OFF and y PAE ON and then FACTORY SETTINGS SCORE TABLE
| RESTORED | will | be | displayed. | TORACOMRY |
Return to game over by depressing — -—_ the ADVANCE pushbutton or by
| turning the game OFF and ON a | GAME | PASS |
second time. “SADIUSTMENTS? i Fall
"FACTORY “OPEN COIN DOOR™ SETTINGS DISPLAYED RESTORED* DISPLAYED
‘OPEN COIN
DOOR POWER ON
POWER OFF AND OFF
AND ON oe a 1 1
“Warning: This equipment generates, uses, and can radiate radio frequency ener gy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.” ll
CAB
INET WIRING
4-PIN loya 10P4
| Aupio IN ——1>] 1 | — | = | 6RI |
VOLUME CONTROL
Aup1lo our —+5] 2
| SHIELD | 4 | L |
4-PIN 3-PIN
| lov2 | 10P2 | 6P3 | 6u3 |
| aupio | —+9] 1 | > BL&cRED | ale | =f] seeaxer |
| AuDio | >} 4 | > REO-BLK | Lt] 2 4 |
10-PIN 15-PIN
| 203 | -2P3 | BP2 | Buz | SSW! auto uP |
| PAO | >| 1 | BLU | 15 |< |
(AUTO UP/MANUAL DOWN) MANUAL ern asw2
| PAI (ADVANCE) | ——+>| 2 | >+ | + | wale | en |
| PA2 (RIGHT COIN) | >| 3 | > YELewHT | 8 | oo ST | |
| HIGH SCORE RESET | >| 4 | > WHT-GRY | | 12 | | | |
| PA4 (LEFT COIN) | >| 5 | > WHT-BLU | 10 |¢ | = | |
| PAS (CENTER COIN) | >| 6 | >-HHTESRN | +<| 9 |¢-—ne | ||
| CA2 (SLAM TILT) —1>] 7 | |>{WHT-ViO | ule | Pio“ BSW. |
GRN-BRN,
| KEY | 9 | NC | 6 |€ |
| 9-PIN | <| 4 |€— | To coin Lockout |
43 4P3
| POWER SUPPLY GND | > 6 | >—BLKCORN |
oswi
| 7-PIN | CASHBOX ADVANCE | a | 1 |
| cpurviogo eoaro | NP | 'F2 | MEMORY PROTECT INTERLOCK | ~ |
| MEMORY PROTECT | RED-ORN | at |
10-PIN 15-PIN
| 3u33P3 | TPL | Tut | ||
| GROUND | [) 10 [>| onn-aux | 2 [eLonn-euk | ||
| PAO | Ls] 6 | >| ORN-BRN | 3 | ¢LORN-oRN | TSWI. | I-PLAYER START | | |
| Pk | >| 5 | |>LORN-RED | 4 | eLORN-RED | TSW2-, 2-PLAYER START |
7SW3
| paz ——t5| 5 | |>LORN | 5 <n | WS FLAP 4 | |
| PAS | 1] 2 {> fORN= VEL | ¢ [ef ORN-YEL | TSW4 MOVE RIGHT #1 | |
| : | - | 735 | ||
| PAS | 15], | |>{ORN-GAN | Jel 7 |eLorn-sew | WS MOVE LEFT #1 |
10-PIN 3u23P2
| pas | >] 4 [>Lonw-suu | a | cLORN-BLU | TSWS. FLAP #2 | |
| Pas | >| 3 |>ORN=vio | 9 [eLORN-vio | TSW7-_ MOVE RIGHT #2 | ] |
| pay | 1.) 2 | |>Lorn-cry | 10 |eLORN-sRY | TSWE- MOVE LEFT #2 |
6-PIN 403 4P3
| >] 2 | [ytwurver ssvac | ||. | wat-ver | -6.avac |
POWER SUPPLY
| >| | |>Lvee | eavac | ||| .| veL_6.avac |
apa ae ui
| +5 voc | > 15 >-GRAY | __+8VDC_1 | Jig Ie} | nc |
Cabinet Wiring Diagram