Asteroids Deluxe DP-165-1st-02B
Asteroids Deluxe (rev 3) (Atari, 1980) · Drawing Package · 1 pages · original scan

INPUTS
LAYER INPUT CIRCUITRY
me —
<7 denotes a test point
OPTIONS INPUT CIRCUITRY
VIDEO INVERTER
The x- and yvideo Inverter circuits are identical; there fore, only the xvideo inverter circuit Is explained. For invvrtered video operation, pin 19 is grounded which turns fon transistor Q13 and turns off transistor Q12. In this state INV is +82 VOC and NONINV is -82 VDC.
For a noninverted video output, pin 19 is unconnected
and floats. In cocktall games, pins 19 and 7 are shorted ‘and have a potential of +5 VDC. This causes transistor {13 to be cut off and transistor Q12 to be turned on. INV Js then -€2 VOC and NONINY is approximately + 8.2 VOC.
{mn upright games, only the x-video inverter is used. In
cocktail games both x-and y-video inverters are used, and
in cabaret games video inversion is not necessary, 80 neither is used.
Sheet 2, Side B DP.165.02 st printing
OUTPUTS
DIAG STEP (diagnostic step), 3. KHz, SELF-TEST ‘SLAM, HALT, FIRE, and HYPER Inputs_are read by the MPU ‘when SINPO (switch input zero ‘enable) is low. Switches to be read are selected by ABO thru ‘AB2 from the MPU. All inputs ‘are read on DB7. Switch inputs ‘are active when pulled to (round, DIAG STEP, 3 KHz, and SELF-TEST are signals read by the MPU to initiate and control the game's self-test procedure. SLAM ls a signal read by the
Thecoin door and some con trol panel switches are read by the MPU when SINPT (switch input one enable) is. low. Switches to. be read are cone ceresion FW is high, the MPU reads the inputs are read on ata line. DB7. Switch inputs Input data from DIP switch LB. are “on” when pulled to ‘When RIW is tow, the MPU ground writes the audio 0 instruction for an output. RINT determines the direc tion of data flow (080-087) as. addressed by ABO-AB3. When
‘The 62 input from the MPU is ‘the operating frequency for the audio UO chip and sets the tim ing for data bus lines O80-DB7.
When PKYDCD, ABIO, B11 are high and ABE is low, a chip select pulse is gated to the audio 1/0 chip. This pulse prepares the audio 1/0 tor ‘operation. ‘The game option switches are read by the MPU when PTS (option switch enable) is low. Switch toggles to be read are ‘selected by ABO and ABt from the MPU. Switch toggles 4,3, and 7 are read on data line DBO and toggles 2, 4, 6 and 8 are read on DBI. Toggle inputs are “on” when pulled to ‘ground,
I exravos
tore — ‘The Custom Audio chip M7/8 generates most of the sounds for Asteroids Deluxe"
oe Se
<7] denotes a test point
exPLOsND
‘The EXPLODE sound is. heard when any object explodes. Noise is sampled at a frequency determined by PZ, and control bits EXPITCHO and EXPITCHI. Changing the samp! ing rate changes the pitch of the ex: plosion. The noise is amplitude ‘modulated in RB by EXPAUDO- EXPAUDS.
RB and P8 generate random noise. This noise is filtered by P11 and produces the rumble sound heard when the ship is thrusting, LAMP, LED, AND COIN COUNTER OUTPUT
-——{BJucrr com {comer com
I 826 0 This circuit consists of coin counter drivers 08, (09, Q10 and data latch M10, clocked by the micro computer's address decoder. When the input to a drivers clocked high, its collector goes low, ground: ing the retun of the coin counter in the coin door When START! or START2 is clocked low, it grounds the START LEDs in the control panel.
VIDEO OUTPUTS
loncnos—3f u et
euo—ile
<< penotes a test point ‘The video-output cicult consists of three individual circuits: Xaxis, Y-axis, and Zaxis ‘The X-axis and Y-axis video-output circuits each consist of a digital-to-analog converter, (OAC), curento-voltage converter, two sample and holds, and amplifier. The Z-axis, video-output circult consists of a shift register and a summer.
X and ¥ Outputs ‘The DACs (011 and B11) each receive binary numbers from the vector generator’s pos tion counter outputs. These numbers represent the location of the beam on the monitor. For the nom inverted X axis, the numbers range from 0 to 1023, where Os at the far left of the monitor screen, §121s at the center, and 1023 is atthe far ight. For the non-inverted Y axis, the numbers range from 128 to 996, where 128 is at the bottom of the monitor Screen, 512s at the center, and 996 is atthe top. When the X axis and Y axis are inverted, the monitor picture is turned upside down. Tis is used for a two-player cocktail game. ‘The DACs convert these binary number inputs to current outputs. The DACs’ current outputs are applied to the pin inputs of current tovoltage converters C12 and A12. From the current-o-voltage converters, the signal is fed to two sample and.hold circuits: (One is non-inverted and the other is inverted. The non- inverted sample and hold consists ‘of one stage of analog switch O12 and capacitor C89 forthe X axis, and B12 and C109 for he axis. The inverting sample and hold consists of inverter Et2, one stage of analog switch 1D12, and capacitor C88 for the X axis and BICT2, B12 and C110 forthe ¥ axis. The sample-andhold circuits are controlled by SHCON (sample and hold control) ‘SHON is derived by gating 3 MHz from the microcomputer clock circuitry and VGCK* ‘rom the vector generator’s state generator. The result of these inputs insures that the nominverted and Inverted analog signals that are applied tothe analog switches have sutficiently stabilized before being applied to the sample-and:hold capacitors.
‘The output swing of SHCON is ~8 to +8 VDC. When SHCON Is high, the voltagé ‘charges oF discharges the sample-andhold capacitors to the X and Y analog voltage ‘value, The voltages are then applied to the inputs of the second analog switch. These Switches select either the non-inverted or Inverted Xaxis and Y-axis outputs. The outputs ‘are then amplified by the second stages of C12 and A12 for an impedance-matched output to the X and Y inputs to the monitor. Since the monitor doesn't have field-adjustable Xand Y gains, the gains are adjustable by variable resistors R120 and R126.
Z Output ‘The Z-axis video output receives six inputs. BVLD (beam vali), from the output of the vector generators position counters, tells the Z axis to draw the line. BLANK (vector ine blank, from the vector generator’s state machine, tells the Z axis to stop drawing a line. SCALEO thru SCALES (grey-level shading scale), from the output ofthe vector generator’s dala latch, tells the Z axis the grey-level shading of the line that is being drawn on the ‘monitor. . When BVLD and BLANK are both high, ahigh is clocked through shift register K9 that tums transistor Q3 off. Tis allows the scale inputs to be passed through transistor Q2. When BLANK goes low, a low is clocked through K9, transistor Q3 tums on, and the ‘signal Is grounded at the base of transistor Q2. ‘The scale Inputs at the base of transistor Q1 determine Qt's emitter voltage, during the line draw period. The SCALEO thru SCALES resistors R36 thru R39, resistor R35, and resistor RAO result in a range of about + 1.0 VDC when all are low and + 4.0 VDC when all are high. The emitter of Qt follows at about + 1.7 to 4.7 VDC, while the emitter of transistor Q2 follows at about + 1.0 to 40 VDC. This output Is applied to the Z input of the ‘monitor. Since there are brightness and contrast controls in the monitor, there are no ad: Justments in this circuit.
ATARI Qs connor cry Sheet 2, Side B
ASTEROIDS DELUXE™ Switch Inputs, Coin Counter, LED and Audio Outputs
(© 1061 Ata, ne.