Mortal Kombat 1 Kit (16-43125-101 Aug 1992) (Bad Scan)
Mortal Kombat (rev 5.0 T-Unit 03/19/93) (Midway, 1992) · Manual · 59 pages · 34 sections · original scan
“S7
MIDWAY August 1992 16-43125-101
MORTAL KOMBAT
KIT
OPERATIONS MANUAL
- Installation & Operation
- Testing & Problem Diagnosis
- Parts Information
- Wiring Diagrams & Schematics
Mortal Kombat Instructions
Insert Coin(s)
In a two player game, the loser pays and the winner stays.
Press the Punch and Kick buttons to attack an opponent.
Use the joystick to make the screen player jump or duck, and move lett or right.
Use joystick and button combinations to discover secret moves.
MIDWAY Manufacturing Company reserves the rights to make modifications and improvements to its products. The specifications and parts identified in this manual are subject fo change without notice.
Mortal Kombat
Kit
TABLE OF CONTENTS Section 1 Operation and Troubleshooting
Conversion Procedures Inspection. Converting from a STREET FIGHTER II* game cabinet. Suggested Control Panel Layout.. PC Board Installation.......... Converting from a typical video game cabinet Suggested Template Layout...... Suggested Control Panel Layout.. Installing PC Boards into a JAMMA Cabin Installing PC Boards into a Non-JAMMA Cabinet. Game Features Starting-up.......... Player Controls... Typical Control Panel Game Operation Control Switches. Control Switch Location Menu System Operation
Diagnostic Tests Switch Tes! DIP Switch Test & Table CPU & Sound Tests Monitor Patterns . Burn-in Tests Coin Bookkeeping. Game Audits...... Game Adjustments. Standard Pricing Table. Custom Pricing Table. PONBOCBVMDAHAWBANND
Section 2 Parts Information
CPU Board Parts... Sound Board Assembly. Sound Board Parts...
Section 3 Diagrams and Schematics JAMMA Chart And Interboard Wiring Cabinet Wiring... Coin Meter Wirin CPU Board Schemati Sound Board Schemati
© Copyright 1992 MIDWAY Manufacturing Company
- STREET FIGHTER II is a Trademark of CAPCOM, USA INC.
Mortal Kombat
Kit
SECTION
Operation & Installation
Safety Notices
The following safety hints apply to all kit operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page, and also all of Section 1, before preparing your kit for play.
Z\\ CAUTION
Notice: Salvaged Parts Parts salvaged from old games are required to complete your kit. These salvaged parts must operate perfectly: otherwise, the converted game cannot perform properly or safely. Always repair circuit board malfunctions and cabinet damage before conversion is attempted.
Notice: Power Supply Be sure the power supply from your old game is capable of +5V de at 5A, -5V de at 1A and +12V at 1A. These operating voltages are necessary for your kit. Your power supply must be FCC approved.
Notice: Monitor This kit is not intended for use with X-Y monitors. Suitable monitors have horizontally mounted CRTs and raster electronics with inputs for red, green and blue video, as well as ite N i: ne i
Notice: Coin Mechanism Be sure to clean and lubricate your old coin mechanisms. Servicing themis crucial to your game's earning potential and operation.
Notice: Coin Meters Coin meters are not provided with this kit. Wiring information is provided as a convenience to the operator.
Notice: Servicing, Installing
Always turn your game Off and unplug it before attempting to service or install your kit.
ATTENTION !
PROPERLY ATTACH ALL CONNECTORS. Be sure that the connectors on each printed circuit board (PCB) are properly connected. If they do not slip on easily, do not force them. A reversed connector may damage your kit and void the warranty. All connectors are keyed to fit specific pins on each board.
1-2
CONVERSION PROCEDURES -
Inspection
Unpack the materials from the carton and inspect for obvious signs of damage. Use this checklist to be sure your kit is complete.
Part No. Item Quantity
| A-13234-40025 | CPU board | 1 | |
| [] | A-14732-40025 | Sound board | 1 |
| [] | H-14925 | Sound/Power Speaker Cable | 1 |
| H-13411 | Main JAMMA Cable | 1 | |
| H-15650 | Volume Control | 1 |
H-15873 Adapter Cable for STREET FIGHTER II 1
| (] H-15874 | Auxiliary Cable | 1 | |
| 16-9383 | Controls Template | 1 | |
| ] 16-43125-101 | Manual | 1 | |
| [] 20-9687-1 | Pushbutton, Red | 4 | |
| {] 20-9687-2 | Pushbutton, White | 4 | |
| [] | 20-9687-3 | Pushbutton, Blue | 4 |
| [] | 20-9694-1 | 8-way Joystick, Red | 2 |
| 31-1612-43125 | Control Panel Overlay | 1 | |
| [] | 31-1644-40025-1 | Marquee | 1 |
| [] 31-1714-43125 | Card & Controls Decal | 1 | |
| [] 31-1715 | Cabinet Side Decal | 2 | |
| [] 5795-10937-18 | 20-pin Ribbon Cable | 1 |
[] Assorted Hardware
Recommended Tools and Supplies [] black semi-gloss paint [] electric drill [] electric screwdriver {] grease pencil or marker [] hex driver [] 180 grit sandpaper or electric sander [] pliers [] razor knife [] soldering iron and solder [] wire cutters [] black electrical tape
1-3
Converting from a STREET FIGHTER II game cabinet
NOTICE
When Midway ships a game, it Is in compliance with FCC regulations. Your sticker Is proof. Ifthe sticker is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game kit does not contain an FCC sticker, call Midway Manufacturing immediately. Cabinet Modifications
- Remove the old decals and artwork and clean the glue residue . Repaint the cabinet with black semi-gloss paint. Allow paint to dry.
- Pencil a line roughly at the top of the old graphic. Lightly moisten the cabinet with soapy water. Apply the decal starting at the top and working down. After the decal is in place, smooth it down, taking care to squeeze out the air bubbles. If you miss an air bubble, pop it with a razor blade or a pin and burnish it down. Allow 12 hours for the adhesive in the decals to set. Remove masking.
- Check the kit for an FCC sticker and apply it over the existing sticker on the cabinet. See NOTICE to the left.
- Apply the Game Play Instruction Decal to the CRT viewing glass. Be sure the decal does not obstruct the CRT.
Control Panel Modifications
- Remove the control panel buttons and joysticks and remove the old vinyl covering and artwork. Tagging the wires as they are removed from the pushbutton and joystick switches will make reinstallation easier.
- Carefully remove the backing on the vinyl control panel overlay. Place the overlay on top of the control panel. Prevent air bubbles from getting under the vinyl overlay.
- After the overlay is in place, use a razor knife to cut holes for the pushbuttons and joysticks. Position the stickers around the approiate hole locations. See the page 1-5 for sticker locations.
- Remove the switch from the pushbutton by pulling the large prong away from the switch, then pull the switch off the housing. Unscrew the nut from the housing. Push the switch housing through the control panel from the front. Screw the nut back onto the switch housing from the back of the control panel. Push the switch back into the switch housing.
- Remove the "E"-ring and slide the shaft and the plastic ring off the joystick base. Be sure that the bushings remainin the base. Screw the base to the underside of the control panel. Slide the plastic ring around the shaft so that the rough side is next to the shaft handle. Slide the shaft through the control panel and base. Replace the "E"ring.
- Mount the volume control, using the screws provided, where it is easily accessible. On top of the cash box, or on the wall near the sound board are two possible locations.
1-4
(WHITE) (WHITE) a
| | | ©) Start | O Stan | | | |||
| High | High | High | High | |) | ||
| Punch | Block | Kick | Punch | Block | Kick | t |
i Jumy Jump Ses
| Flip | i | Flip | (RED) (WHITE) (BLUE) | Flip | | | Flip | (RED) (WHITE) (BLUE) | |
| Move Move (RED) (WHITE) (BLUE) (RED) (WHITE) (BLUE)
| Duck | Low | Block | Low | Duck | Low | Block | Low |
Punch Kick Punch Kick
Typical control panel layout & sticker locations for modification of a STREET FIGHTER I! contro! panel
PC Boad Installation
- Replace the existing CPU board and sound board with the Mortal Kombat CPU board and sound board.
- Plug the JAMMA connector into the CPU board at J1. Plug the 10-pin connector of the Adapter cable into the 10-pin JST type connector from the control panel. Be sure to match the wire colors of both connectors. Plug the other end of the Adapter cable into the CPU board at J4.
- Connect the ribbon cable from P1 on the sound board to J8 on Note the CPU board. Be sure that the red line goes to the same pin on both boards. Connect the wire harness cable from P7 (speaker), and P6 (power), on the sound board to J2 (sound The ribbon cable may need to be twisted in order to connect it properly. power speaker connector) on the CPU board. ¥
- J6,J7, J9 on the CPU board are not used.
- Place the FBI Warning Label on the inside of the cabinet next to the PC boards. Be sure the label is completely visible.
orc rr cere ’
| To JST type Connector | 14 CPU Board | ' |
——from control panel cable —
| Ground | Black [4 | 1 | 1 | |4 | Black | ' |
| Grou | lack 2 || 2 | To CPU board J. 2 | "2 | INC | H | |
| Pi | LowPunch | Violet!3 || 3 | 3 | 3 | |NC | : |
| P1_ | Block | Gray} 4 |) 4 | 4 | |!/4 | Orange | ' | |
| P1_LowKick | _White|s || 5 = Las | ‘15 | Black | i | |||
| NIC | 6 | ge | ES | Iie | Key | ' | |
| P2 | Low Punch Orange | 7 | 7 ee — | 4/7 | Blue | ' | ||
| P2 Block | Green| | g | jig ae | 8 | |g | Green | ' |
| P2__Low Kick | 9 | 9 | 9 | | 9 | Violet | t | |
| NC] 10 |} 10 | 40 |*| 10 | White | ' |
44 |{) 41 | N/C ‘ 12 |*| 12 | Gray ' Adapter cable for STREET FIGHTER II conversion
1-5
NOTICE
When Midway ships a game, it is in compliance with FCC regulations. Your sticker is proof. If the sticker is missing or damaged, legal repercussions to the owner or distributor of the game may result. Ifyour game kit does not contain an FCC sticker, call Midway Manufacturing immediately. Converting from a typical video game cabinet
Cabinet Modifications
- Repaint the cabinet with black semi-gloss paint (games with wood grain sides: remove the old decals and artwork and clean the glue residue before painting). Allow paint to dry.
- Pencil a line roughly at the top of the old graphic. Lightly moisten the cabinet with soapy water. Apply the decal starting at the top and working down. After the decal is in place, smooth it down, taking care to squeeze out the air bubbles. If you miss an air bubble, pop it with a razor blade or a pin and burnish it down. Allow 12 hours for the adhesive in the decals to set. Remove masking.
- Check the kit for an FCC sticker and apply it over the existing sticker on the cabinet. See NOTICE to the left.
- Apply the Game Play Instruction Decal to the CRT viewing glass. Be sure the decal does not obstruct the CRT.
Control Panel Modifications
1, Remove the control panel buttons and joysticks and remove the old vinyl covering and artwork.
2, Use the control panel template to help you design your control panel. You will need to use the template twice. Once for the left Playercontrols and once forthe rightplayercontrols. Referto page 1-7 for suggested template layouts.
- Drill holes as needed for the joysticks and control panel buttons. Plug previous holes with wood blocks, putty, cardboard or epoxy. File the new holes smooth.
- Carefully remove the backing on the vinyl control panel overlay. Place the overlay on top of the control panel. Prevent air bubbles from getting under the vinyl overlay.
- a) After the overlay is on securely, use a razor knife to cut holes for the control panel buttons and joysticks.
- Position the stickers around the appropriate locations. Refer to page 1-7 for suggested control panel button and joystick sticker locations.
- Remove the switch from the pushbutton by pulling the large prong away from the switch, then pull the switch off the housing. Unscrew the nut from the housing. Push the switch housing through the control panel from the front. Screw the nut back onto the switch housing from the back of the control panel. Push the switch back into the switch housing.
1-6
- Remove the "E"-ring and slide the shaft and the plastic ring off the joystick base. Be sure that the bushings remain in the base. Screw the base to the underside of the control panel. Slide the plastic ring around the shaft so that the rough side is next to the shaft handle. Slide the shaft through the control panel and base. Replace the "E"-ring.
8, Mount the volume control, using the screws provided, where it is easily accessible. On top of the cash box, oronthe wall near the sound board are two possible locations.
Suggested control panel template layout
Suggested control panel layout and sticker locations for a typical video game control panel
(WHITE) (WHITE)
© Start (©) Start
Installing the PC boards and wiring into a JAMMA game cabinet
Note
If you choose to use your own JAMMA Cable and not the one provided in the kit, be sure to check the JAMMA Cable Chartto verify that it is compatible.
Z\ CAUTION Properly insulate any unused wires within the JAMMA cable, especially the gray, gray-green and gray-yellow wires. This is a fully wired JAMMA cable. Many of the wires will not be used for this kit. These wires have been installed so that you can use this cable for future kits
The ribbon cable may need to be twisted in order to connect it properly. Disconnect and remove the existing CPU board and sound board in the JAMMA game cabinet.
Mount the CPU board inside the JAMMA game cabinet where the old CPU board was located. Mount the sound board next to the CPU board using the stand-offs and screws provided.
If you choose to use the JAMMA cable provided with the kit, disconnect your old JAMMA cable from the speaker, power supply, control panel switches (may already be disconnected) and coin door. Remove the cable fromthe game. If you are not going to use the JAMMA Cable provided with the kit, check the JAMMA Cable Chart to be sure your cable is compatible. Leave your power supply chassis as is.
Connect the JAMMA cable to J1 on the CPU board. Use the Cabinet Wiring Diagram for reference and solder the correct JAMMA cable wires to the speaker. Then, connect the wires to the coin door, power supply and control panel.
Player 1 has orange-color stripe wires except for Start 1 which has a yellow-green wire. Player 2 has yellow-color stripe wires. Follow the Control Panel Wire Color List on the inside of the back cover or, the Cabinet Wiring Diagram in Section 3 of this book.
Connect the Auxiliary cable to J4 of the CPU board. Follow the Cabinet Wiring Diagram or the Control Panel Wire Color List and connect the wires to the switches for the Low Punch and Low Kick buttons for players 1 & 2.
Connect the ribbon cable from P1 on the sound board to J8 on the CPU board. Be sure that the red line goes to the same pin on both boards. Connect the wire harness cable from P7 (speaker), and P6 (power), on the sound board to J2 (sound power speaker connector) on the CPU board.
J6, J7, J9 on the CPU board are not used.
Place the FBI Warning Label on the inside of the cabinet next to the PC boards. Be sure the label is completely visible.
Installing the PC boards and wiring into a NON-JAMMA game cabinet
. Disconnect and remove the existing CPU board and sound board in the game cabinet.
Mount the CPU board inside the game cabinet where the old CPU board was removed. Mount the sound board next to the CPU board using the stand-offs and screws provided.
Leaving several inches of wire, cut the wires at the coin door, control panel switches (which may already be disconnected) speaker and power supply. Remove the existing harness from the cabinet. Leave the cable hooks in place.
Install the JAMMA cable providedin this kit. Players 1 & 2, the coin door and the power supply wires are bundled together in individual groups. Insure that the cable is properly dressed and supported.
. Connect the JAMMA cable to J1 on the CPU board. Use the Cabinet Wiring Diagram for reference and solder the correct JAMMA cable wires to the speaker. Then, connect the wires to the coin door, power supply and control panel.
Player 1 has orange-color stripe wires except for Start 1 which has a yellow-green wire. Player 2 has yellow-color stripe wires. Follow the Control Panel Wire Color List on the inside of the back cover or, the Cabinet Wiring Diagram in Section 3 of this book.
. Connect the Auxiliary cable to J4 of the CPU board. Follow the Cabinet Wiring Diagram or the Control Panel Wire Color List and connect the wires to the switches for the Low Punch and Low Kick buttons for players 1 & 2.
Connect the ribbon cable from P1 on the sound board to J8 on the CPU board. Be sure that the red line goes to the same pin on both boards. Connect the wire harness cable from P7 (speaker), and P6 (power), on the sound board to J2 (sound power speaker connector) on the CPU board.
. J6, J7, J9 on the CPU board are not used.
. Place the FBI Warning Label on the inside of the cabinet next to the PC boards. Be sure the label is completely visible.
1-9
Note
Be sure all spliced wires are well insulated with black electrical tape.
Z\ CAUTION Properly insulate any unused wires within the JAMMA cable, especially the gray, gray-green and gray-yellow wires. This is a fully wired JAMMA cable. Many of the wires will not be used for this kit. These wires have been installed so that you can use this cable for future kits
The ribbon cable may need to be twisted in order to connect it properly.
GAME FEATURES
Note STARTING UP
Whenan errorisdetectedduringStart- Switch on power to the game. A “rug” pattern appears on the CRT up Tests, game start-up does not screen. When the “rug” pattern ends, the screen shows CHECK- Progress, and an error message ING SCRATCH RAMS, and then CHECKING ROMS. The next appears on the screen. screen shows MORTAL KOMBAT REVISION LEVEL, CMOS TEST OK and the COIN SETTING. The game then begins the Attract Mode.
Insert the desired amount of coins or tokens. Press the appropriate Start button.
Player Controls
Start Buttons Each player has a Start Button which allows him/her to begin or continue play.
£4 High Kick/High Punch Buttons Allows the screen player to kick or punch an opponent in the upper body.
£3 Low Kick/Low Punch Buttons Allows the screen player to kick or punch an opponent in the lower body.
Block Buttons
Jump Flip, | Flip
Block
Duck
Control Panel
1-10
GAME OPERATION
It is suggested that the MORTAL KOMBAT Control Switches be located inside the coin door. These switches allow the operator to customize some features of the game.
{ CONTROL SWITCHES The COIN DOOR SLAM TILT SWITCH detects any forceful vibrations against the Coin Door. This eliminates pounding for tree games. (Optional Switch.)
The VOLUME CONTROL allows increasing or decreasing the volume level of the game music and speech. For greater profits, set your game's volume level at its maximum.
The TEST/DIAGNOSTICS SWITCH allows you to activate the game's Menu System. Move the Test Switch to access the Main Menu. To exit the Menu System, select EXIT TO GAME OVER from the Main Menu, then press any control panel button. This function is also available on DIP Switch #2 position #8. (Optional Switch.)
The SERVICE CREDIT SWITCH is a special feature switch that allots credit without affecting the game's bookkeeping total. (Optional Switch.)
Slam Tilt Switch
Volume Control
Test/Diagnostics Switch
Service Credit Switch Cash Box Enclosure
Typical Control Switch Locations
1-11
MENU SYSTEM OPERATION
OPERATION All MORTAL KOMBAT Game Audits, Adjustments, and Diagnostics are options of the Main Menu. Each option, inturn, has its own menu, listing several choices that you may act upon as desired.
Move the Test Switch (if installed), or close Switch #8 of DIP Switch Bank #2, to activate the Main Menu (shown below). Game adjustments, bookkeeping, and diagnostics are all accessible from this menu.
Move any joystick up or down to cycle through the menu options. Notice that the options are highlighted in sequence. Press any button to activate a highlighted option.
Select With Any Stick Activate with Any Button
Diagnostic Tests Coin Bookkeeping Game Audits
Game Adjustment
Utilities Exit Test Menu
Main Menu
1-12
DIAGNOSTIC TESTS To enter the Diagnostic Tests from the Main Menu, move any joystick to select (highlight) the Diagnostic Test option, and press any control panel button to activate the option.
Select With Any Stick Activate With Any Button
Switch Test DIP Switch Test CPU Board Test Sound Board Test Monitor Patterns Burn-in Test Return To Main Menu
Diagnostic Menu
Switch Test The Switch Test allows the operator to test the switches on the control panel and the coin door.
Select the Switch Test by using any joystick to highlight the Switch Test option; then, press any control panel buttonto activate it. The top of the screen shows a layout of the control panel and the bottom of the screen lists the coin door switches. Pressing a switch causes the corresponding switch location on the screen to light. Release the switch and the screen returns to normal.
Press the Start buttons together to return to the Diagnostic Menu.
DIP Switch Test
Note The DIP Switch Test allows the operator to check the position of the
two 8-position DIP Switches on the CPU Board. The operator can Setting the positions of DIP Switch 1 also change the setting of each position of each DIP Switch during to Off means thereis violence, blood this mode. low blows, and attract mode sounds in the game. Use any joystick to select the DIP Switch Test and any control panel button to activate it. The screen displays a layout of their current settings.
To change a DIP Switch setting, press the switch to the desired setting, then check the screen to verify that the switch now shows the new setting.
Press any control panel button to return to the Diagnostic Menu.
DIP Switch 1 Settings Table
| swi| | sw2] | swa] Sw4/sws | Sw6| | SW7|swe |
Violence On ont: On
Blood in game one On
Low Blow in game or: On
Attract Sounds On om: On Not Used ont | ont | On) one On | On | On | On
DIP Switch 2 Settings Table
| Swi | swe | |sws3 | _|swa | [sws | [Swe | Sw7 | Swe |
Coinage DIP Switch on CMOS On
| Coin Settings | oft'| | on: | one | ||
| USA1 | = Gert | Fr | On | of | | om |
| USA2 | Ger2—Fr2 | ot | lon | | off |
| USA3 | Gor3 | Fr | Ps | ” |
| USA4 | Gord | Fr4 | nN) | On | Off |
USAECA GerECA Freca | Of | Off | On
| NU | NU | NU | on | of | | on |
| NU | NU | NU | Off | On | On |
| Free Play Free Play FreePlay| | On | On | On | _ | |
| ion | on | | one |
German on | on
| French | o | hee | |
| Not Used | _ | i | J |
One Counter a Two Counters a
Test Switch . Game Mode ou Test Mode ee —— On
- Indicates Factory Setting
1-14
CPU Board Test The CPU Board Test (much like the Start-up Test) allows the operator to check the RAMs and ROMs.
Select the CPU Board Test with any joystick; then, press any control panel button to activate the automatic test of the CPU Board's RAMs and ROMs. When this testis activated, a “rug” pattern appears on the screen. The screen then changes to show the layout of the RAMs, and ROMs. A ROMor RAM location that is shown as black with a white outline is used and should turn either red or green. A ROM or RAM location that is shown as gray with a white outline is not used in this game. During the test, ROM or RAMs are good, if they turn green; they are faulty, if they turn red.
The CPU Test pauses when a bad ROM or RAM isdetected. Press any button to continue the test.
Sound Board Test The Sound Test allows listening to some of the sounds that this game is capable of producing. This test also emits a tone for each fault that is detected.
Select the Sound Board Test with any joystick; then, press any control panel button to activate the test. The screen displays two test options:
GENERAL TEST analyzes the sound circuitry. The screen shows a list of error codes. A successful test causes a single “tone” to sound. Detection of a fault causes a series of tones or no tone at all to sound.
PLAY SOUNDS tests synthesized & digitized sounds from the Sound Board. Advance to the next sound by moving any joystick, and press any control panel button to activate the sound.
Select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU. Press any control panel button to activate your selection.
General Test Play Sounds Back To Diagnostic Menu Return To Main Menu
Sound Test Menu
1-15
Monitor Patterns The Monitor Patterns Test provides a menu for testing the monitor. Select the test with any joystick and activate with any control panel button. Once the Monitor Patterns Test is activated, move any joystick to select a test option; press any control panel button to activate the option. Press any control panel button again to return to the Monitor Patterns Test menu.
Select With Any Stick
Activate With Any Button
Red Screen Green Screen Blue Screen Color Bars Crosshatch Patterns Back To Diagnostic Menu Return To Main Menu
Monitor Pattern Menu
The RED, GREEN, and BLUE SCREEN tests fill the screen with either red, green or blue. The COLOR BARS test fills the screen with several shades of colors to help with red, green and, blue level adjustments. Each color should appear sharp and clear. The CROSSHATCH PATTERNS testiills the screenwith agridand a series of dots. The grid and the dots should be clear. The dots should appear round.
Ifany of the Monitor Pattern Tests shows aneed for adjustment, use the proper white knobs on the Monitor Board.
Use any joystick to select RETURN TO MAIN MENU or BACK TO DIAGNOASTIC MENU and activate with any control panel button.
Burn-in Test The Burn-in Test continually repeats the CPU Board Test. Move any joystick to select the Burn-in Test; then, press any control panel button to activate the test. When the Burn-in Test detects an error, the test stops and displays an error message on the screen. The second page of the Audit Table specifies the number of Burn-in cycles successfully completed. Use this test to find intermittent CPU problems.
To exit this test, switch the game Off then On again.
1-16
COIN BOOKKEEPING To enter the Coin Bookkeeping from the Main Menu, move any joystick to select the Coin Bookkeeping option; then, press any control panel button to activate it.
The Coin Bookkeeping Table records the coinbox totals and game play counters. The left side of the table names the bookkeeping item; the right side shows the number of coins, credits, or plays for each item.
To exit Coin Bookkeeping, move any joystick to select RETURN TO MAIN MENU; then, press any control panel button to activate it.
Left Slot Coins Right Slot Coins Third Slot Coins Fourth Slot Coins Service Credits Paid Credits Total Plays eoo0ecco0o
More Detailed Data Return To Main Menu
Coin Bookkeeping Table
Left Slot Coins Right Slot Coins Third Slot Coins Fourth Slot Coins Total Collections ooooa
| Clear Coin Meters Return To Main Menu
Total Collection Table
1-17
GAME AUDITS To enter Game Audits from the Main Menu, move any joystick to select the Game Audits option; then, press any control panel button to activate it. To advance to the next (or return to the previous) page of the Game Audit Table, move any joystick to select either "Next Audit Page”, or "Previous Audit Page”; then, press any control panel button to change the page.
The Game Audits Table records the game play statistics. The left side of the table names the Audit item; the right side shows the amount of play.
Hours Game was On Hours Played with 1 Player Hours Played with 2 Players Total Plays 1 Player Continues Taken 2 Player Continues Taken Highest Battle Reached Winning Streak Reset Count Burn-in Loops Successfully Completed eccooooc0c00
Next Audit Page Return To Main Menu
Page 1 of Audit Table
Cage Chosen Kans Chosen Raiden Chosen Liu Kang Chosen Sub-zero Chosen Scorpion Chosen Sonya Chosen Error Traps eceooo0c0o0ce
Previous Audit Page _ Return To Main Menu
Page 2 of Audit Table
To exit the Game Audit Table, move any joystick to select RETURN TO MAIN MENU; then, press any control panel button to activate your selection.
1-18
GAME ADJUSTMENTS Move any joystick to select the Game Adjustment option on the Main Menu; then, press any control panel button to activate it.
The Game Adjustments Menu allows the owner/operator to change the Game Pricing and Game Difficulty.
The Game Adjustments Menu offers several options. Each option has several choices. Move any joystick to select an option; then, press any control panel button to activate that option. The next menu screen provides a setting choice. Move any joystick to modify the setting value; then, press any control panel button to lock in the new value and return to the Adjustment Menu. Move the joystick up to increase the setting value, move the joystick down decrease the setting value.
To exit the Adjustments Menu, use any joystick to select RETURN TO MAIN MENU; then, use any control panel button to activate your selection.
Select With Any Stick Press Any Button To Modify
Return To Main Manu Standard Pricing Custom Pricing Free Play Computer Difficulty Winning Streak Reset Return To Main Menu
Game Adjustment Menu
1-19
Game Adjustments are explained in more detail on the following page.
Adjustment values set by DIP Switch, override adjustment values set by the menu system.
Game Adjustments
Standard Pricing Standard Pricing allows the operator to choose any of the "Standard" selections for the Standard Pricing Table. See page 1-21.
Modify the setting value with any joystick. Press any control panel button to lock in the new value and return to the Adjustment Menu.
Custom Pricing Custom Pricing allows the operator to install pricing other than that of the Standard Pricing Table. Custom Pricing also allows the operator to select the maximum amount of credits per game, the amount of credits required to start a game, and the amount or credits required to continue a game. This option is being adjusted from the Dip Switch Settings. See page 1-22.
Modify the setting value with any joystick. Press any control panel button to lock in a new value and return to the Adjustment Menu.
Free Play This option selects free play. The setting choices for this adjustment are:
- No (factory)
- Yes
Computer Difficulty This option determines the difficulty level of game play. The setting choices for this adjustment are: -1 (Extra Easy) -2 (Easy) -3 (Medium; factory) -4 (Hard) -§ (Extra Hard)
Winning Streak Reset This option resets the highest scores after a selected amount of games are played. The setting choices for this adjustment are:
- Reset every 5,000 games.
- Reset every 10, 000 games (factory).
- Reset every 15, 000 games.
- Do Not Reset.
1-20
Standard Pricing Table
| 1 | a | a | ||||
| Name | Settings — | Left Chute | | Center Chute | Right Chute | Fourth Chute | |
| aoa. | Credit'Coin | —eae | —— | _ | ||
| USAt | j 125e | (2 to Start; 2 to Continue) | 25 | | | ese | |
| UsA2 | | | ese | (2to Start; 110 Continus)} | 25¢ | 25¢ | |
| USA3 | | 125e | (10 Start; 110 Continue)| | —5e. | 25¢ | ||
| USA | | 17802, 2/$1.00 (1 to Start; 1 t0 Continue) | 25¢ | | | 25e | ||
| USAS | ¥50¢, 4/$1.00 (2 to Start; 1 10 Continuo) | 25¢ | | | Pbe | ||
| USAS | 1506 | (1 to Start: 1 10 Continue) | 25e | ! | | | ese |
| USAT | 1150S, /$1.00 (1 to Start; t to Continue) | 25e | | | 26e | ||
| USA8 | 1/80¢, 4/$1.00 (1 to Start; 1 10 Continue} | 2o¢ | : | $1.00 | 25e | |
| USAECA | 125¢, 4/$1.00 (2 to Start; 2 10 Continue) | $1.00 | 1 | 10¢ | 28 | bid |
| German 1 | | 110M, 6/5DM | 1DM | | | 5DM | ||
| German 2 | 41M, 7/5DM. | 10M | 50M | |||
| | German3 | | 710M, a/SDM | 1DM | SDM | t | ||
| German 4 | | 110M, S/SDM | 1DM | | | SDM | i | |
| Germans | | 1/10M, 6/50M | 1DM | 50M | |||
| GermanECA | | V/1DM, 2/2DM, 6/5DM | 50M | | | 10M | 20M | i |
ae —_
| | France 1 | 2/5, SI1OF | SF | Hl | 10F | |||
| | France 2 | 2ISF, 4/10F | 5F | 10F | ||||
| France 3 | TSE, SOF | | | SF | 10F | |||
| France 4 | 415F, 210F | | | 8F | 10F | |||
| France 5 | 2ISF, SIT0F, 1172 x 10F | OF | 10F | i | |||
| France 6 | | 2/SF, art0F, 912 x 10F | BF | yor | | | |||
| | France 7 | 4/SE, S/10F, 7/2 x 10F | | | ge | 10F | i | ||
| France @ | | VSR, 2/108, 6/2 x 10F | SF | tOF | \ | i | ||
| France 9 | | V9 x1, 2/5F | iF | SF | H | ' | ||
| | France 100 | | V2 x 1F, S/5F | 1F | e | ||||
| | France 11 | 173 x 1F, 215K, 5/2 x SF | 1F | SF | | | | | ||
| France 12 | 1/2 x 1F, S/5F, 7/2 x SF | { | 1F | SF | H | ||
| France ECA | 4/3 X 1F, 2/5F, 5/2 X SF | aE | | | 40F | | | SF | j |
| Canada | | 412 x25e, 3/$1.00 | | | 28e | $1.00 | |||
| | Swiss 1 | | IAF, 6/SF | SF | | | | | |||
| Swiss 2 | AF, 75 | | | SF | | | |||
| Swiss 3 | | AMF, SSF | 1 | SF | i | |||
| i | — | an | | | ||||
| | ttaly | 1/500 lire | 500 lire | | | 500 ive | | | ||
| UK1 | 1/20P, 3/50P | 20P | | | sop | j | ||
| UK2 | 2/20P, SiS0P | 20P | i | | | 50P | | | |
| | UK ECA | | ¥20P, 3/60 P, 7181.00 | £1.00 | 20P | 50P | top | i | |
| | UK Elec wicCu | 1/30P, 2/50P, 4/£1.00 | | | exo | CCU | ||||
| | | — | an | = | _ | |||
| | Spain | | 1/100 peseta, 6/500 peseta | 100 peseta | 500 peseta | ||||
| Spain 2 | 1/100 paseta, 5/500 peseta | 100 peseta | | | 500 peseta | |||
| Australia t | 113 x 20¢, 2181.00 | 20 | | | $1.00 | |||
| ‘Australia 2 | 115 x 20€, 1/$1.00, 9/20¢ | | | 20¢ | $1.00 | |||
| Japan 1 | 1/100 yan | 100 yen | |||||
| Japan 2 | | 2/100 yen | 100 yen |
“Austria 4 | 418 schilling, 2/10 schilling
| i} | 5 schilling | 10 schiling | | | |||
| | Austria 2 | | 2 x5 schiling, 9/2 x 10 schiling | | | Sschiling | 10schiling | | | |
| Belgium 4 | ] 1/20F | 20F | 20F | |||
| | Belgium 2 | ‘9/20F | 20F | 20F | j | | | |
| Bolgium 3 | 2R0F | 20F | . | 20F | ||
| | Belgium ECA | 1/25¢, 4/$1.00 | SOF | oF | 20F | ||
| Sweden | 1/3 x 1 krona, 2/ krona | 1 krona | S krona | |||
| ~ | - | | | a | |||
| New Zealand1 | 1/3 x20e | 20e | 20e | ||||
| Now Zealand2 | 12x 20e | ae | [ae | | L | 20e | _ | |
| Netherlands | S/1HFI, 9/2.SHFI | tHFI | i | | | 2 SHEL | |
| Finland | it markka | Tmarkka | | | |||
| | Norway | 1/2 x1 krone, 3/5 x t krone: | bt krone | 1 krone | |||
| H | T | se | Pr | |||
| Denmark | 1/2. x1 krone, 3/5 krone, 7/2xSkrone | | | 5 krone | | | ||
| Antilios | 1/28¢, 4/1 guilder | | | 25 | 1 guilder | | | |
| Hungary | 4/2 x 10 forint, 2/2 x 20 forint | | | rOforint | | | 20 forint | | |
If option desired is not shown above, use Custom pricing. 1-21
Custom Pricing
Select With Any Stick Press Any Button To Modify.
Return To Adj. Menu
- Left Chute Units
- Right Chute Units
- Third Chute Units
- Fourth Chute Units
- Units/Credits
- Units/Bonus
- Minimun Units Required
- Credits To Start
- Credits To Continue
- Coins Per Dollar Maximum Credits Return To Adj. Menu
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) Coins inserted accumulate units. This adjustment specfies the number of units given for each coin in the fourth chute (see “units/credit").
This is the number of coin units required to buy one credit.
One bonus credit is awarded after this many coin units have accumulated,
No credits will be awarded until this many coin units have accumulated.
Each player needs this many credits to begin a game.
Each player needs this many credits to continue a game.
The detailed bookkeeping screen shows total collections based on this many coins per dollar. (Set to zero to disable the display of money totals)
This is the limit for the credits counter. Additional coins inserted will be lost (factory setting: 30)
1-22
UTILITIES
Move any joystick to select the Utilities option on the Main Menu; then, press any control panel button to activate it.
The Utilities Menu allows the owner/operator to clear the game's bookkeeping memory and to install a custom message.
Select With Any Stick Activate With Any Button
Clear Credits Clear Coin Counters Clear Game Audits Reset High Score Default Adjustments Full Factory Restore Return To Main Menu
Utilities Menu
Move any joystick to select an item from the Utilities Menu; then, press any control panel button to activate that item. After an item has been activated, you are given the option of resetting that item or not. For example,
CLEAR COIN COUNTERS ? ARE YOU SURE ?
Move any joystick to choose YES or NO; then, press any control panel button to lockin your choice and to return to the Utilities Menu. To exit the Utilities Menu, move any joystick to select RETURN TO MAIN MENU; then press any control panel button to activate your selection.
1-23
Problem
No Picture or Distorted Picture.
Turn game On and nothing happens.
No sound.
No General Illumination.
Move joystick and the screen player does not move.
Press Start Button and nothing happens.
Press any control panel button and screen player does not move.
No credit given when coins are inserted.
Too many credits for number of coins inserted.
Game stays in test mode.
TROUBLESHOOTING
Possible Solution
Check for faulty video board or monitor. Check for disconnected video signal cable.
Check line fuse. Check for +5Vde at pins C, D, 3, and 4 of the JAMMA Connector.
Check the speaker and speaker connection to pins L and 10 on the JAMMA Connector. Check volume control setting. Check for +12V dc at pins F and 6 on the JAMMA Connector. Check interboard wiring from CPU Board to the Sound Board.
Check the 1A., S.B. fuse.
Check for open wires between the joystick and CPU Board. Check for contamination on joystick switch contacts and CPU Board pins. Check for proper ground.
Check for open wires between the button and CPU Board. Check for contamination on CPU Board pins or the button switch blade contacts. Check for proper ground.
Check for open wires between the button and CPU Board. Check for contamination on CPU Board pins or the button switch blade contacts. Check for proper ground.
Check DIP switch coin setting. Check for contamination on coin switch contacts. Check for an open wire between Coin Switch 1 and pin 16 on the AMMA Connector or Coin Switch 2 and pin T of the JAMMA Connector.
Check Game Pricing setting. Check for a short betweenpins T & 16
onthe JAMMA Connector.
Check that the Test Switch in the coin door is set to Off.
1-24
MORTAL KOMBAT
SECTION
two
PC Board Parts
A-13234-40025
CPU Board Assembly
Mtg onca3y Erescoid
2-2
A-13234-40025 CPU Board Parts
| Part Number | Designator | Description | Part Number | Designator | Description |
| 5281-09737-00 | ut | Ic, 7aL S86 | 5671-09019-00 | LED1, LED2 | LED, Red |
| 5317-12211-00 | U2, U20, U24, U43, | IC, 74ALS541 | 5551-09822-00 | u | Inductor, 4.7uH |
| Us1, Us2, U70 | 5645-09025-00 | Ds1, Ds2 | DIP Switch 16-pin | ||
| 5317-12212-00 | U3, U6, U7,U21, | IC, 74ALS574 | 5641-12551-00 | swt | Pushbutton Switch |
| U25, USO, U58, U63, | 5881-12315-00 | BI | Battery Holder | ||
| Us4, U71, U72, U74, | 5791-10862-08 | J2 | 8-pin Connector | ||
| U73, UB4, UBS. | 5791-12461-12 | Ja | 12-pin Connector | ||
| 5317-12208:00 | U4, U22, U54-U57, | IC, 74ALS245 | §791-10850-00 | 6, U7 | 26-pin Ribbon Connector |
| US9, U60, U75-U78, | 5791-09437-00 | JB | 20-pin Ribbon Connector | ||
| Uso, U81, U94, U110 | 5791-12461-10 | 12 | 10-pin Connector | ||
| 5340-12840-00 | U5, U23 | IC, 8K x 8 Static RAM | 58700-12252-00 | U12-U15 | 24-pin Socket |
| §700-12047-00 | U8, U52, US3,U65 | —24-pin Socket | 5791-12461-05 | 13 | 5-pin Connector |
| 5521-10421-00 | U6 | 48Mhz Xtal | 5791-12461-04 | J3 | 4-pin Connector |
| 5521-10318-00 | ui7 | 24Mhz Xtal | 5791-12461-20 | J9A, J9B | 20-pin Connector |
| 5283-10468-00 | U19, Uss | IC, 74F74 | §791-12461-04 | Jia | 6-pin Connector |
| 5019-10849-00 | U27, U34, U44, 4B | 10002 DIP Res. | 5880-11056-00 | BI | Lithium Battery, 3A |
| 5286-13209-00 | u35, | IC, 744500 | 03-8338-1* | 1/4" Spacer | |
| 5700-12253-00 | Us6 | 68-pin Socket | A-5346-40025-1 | us | IC, PLD Color RAM Control |
| 5280-09309-00 | us7 | IC, 7407 | 5400-12220-00 | uUs6 | IC, TMS34010, 50 GSP |
| 5281-09487-00 | u38 | IC, 7aL S74 | A-5346-40025-2 | uso | IC, PLD Address Decode |
| 5434-12255-00 | u3s9 | MAX691 | A-5346-40025-3 | ust | IC, PLD Video RAM Control |
| 5700-09915-00 | Ua0, U41, Ua2, | 20-pin Socket | A-5346-40025-4 | a2 | IC, PLD Local Control |
| 5311-12287-00 | Uae, U47, U87, U100 IC, 74HC541 | 5340-12558-00 | uaa | IC, 8K x 8 Static RAM, 150ns | |
| U101, U103, U104 | A-5346-40025-5 | us2 | IC, PLD Video RAM Sequencer | ||
| 5700-10176-00 | uaa | 28-pin Socket | ‘A-5346-40025-6 | Us3 | IC, PLD Image ROM Control |
| 5311-12285-00 | U51, U73, U82 | IC, 74HC573 | ‘A-5346-40025-7 | U65 | IC, PLO Miscellaneous Control |
| 5340-1201 4.00 | Us6-Us9 | IC, 4464 DRAM, 64 x 4 | A-5343-40025-1 | usa | IC, Game EPROM |
| 5283-10552-00 | a3 | IC, 74F04 | A-5343-40025-10 | U105 | IC, Game EPROM |
| 5370-1 2602-00 | use | IC, ULN2064B | A-5346-40025-8 | Units | IC, PLD Autoerase Controller |
| 5317-12023-00 | uss | IC, 74ALS138 | 5410-12239-00 | ug9 | IC, Custom ASIC |
| 5700-12088-00 | U89-U93, U95-U98, | —32-pin Socket | §340-12213-00 | U10-U15, U28-U33__IC, VRAM 64K x 4, 150ns | |
| Us05-U109, U111-U114 | 5341-13297-00 | unit | IC, ROM | ||
| §700-12254-00 | us9 | 114-pin Socket | 5341-13297-01 | Ugs | IC, ROM |
| 5317-42024-00 | ur02 | IC, 7448139 | 5341-13297-02 | 106 | IC, ROM |
| 5700-08985-00 | U115, | 40-pin Socket | §341-13297-03 | U2 | IC, ROM. |
| 5010-08991-00 | Ri, R24, R27 | 4.7KQ Res... 5%, 1/4W | 5341-13297-04 | uss, | IC, ROM |
| 5010-10204-00 | R2, A7, R12 | 1KQ Res., 2%, 1/4W | 5341-19297-05 | uUs07 | IC, ROM |
| 5010-10205-00 | R3, RB, R13 | 2KQ Res., 2%, 1/4W | 5341-13297-06 | Un13 | IC, ROM |
| 5010-10000-00 | R4, RG, R14 | 3.9KQ Res., 5%, 1/4W | 5341-13297-07 | u97 | IC, ROM |
| 5010-09219-00 | RS, R10, RIS | 8.2KQ Res., 5%, 1/4W | 5341-13297-08 | Ui08 | Ic, ROM |
| 5010-08772-00 | Re, R11, R16 | 15KQ Res., 5%, 1/4W | 5341-13297-09 | uta | IC, ROM |
| 5010-09001-00 | R23, R25 | 3300 Res., 5%, 1/4W | 5341-18297-10 | uss | IC, ROM |
| 5010-09036-00 | R26, A29-R34, R50 | 10082 Res., 5%, 1/4W | §341-13297-11 | Ur03 | IC, ROM |
R51
| 5010-09416-00 | R35-R97, R46-R4B | 4700 Res., 5%, 1/4W |
| '5010-08997-00 | R38-R45, | 2.7KQ Res., 5%, 1/4W |
| 5010-09534-00 | W2, We, W11, W12, | 02 Res., 1/4W |
w14, W21, W22, W24, W27, W29, W30, W32, W34, W36, W39, W41, wa2, W45, W47, W48, WSO, W52, WSS, W57, WS8, W60, W62, Wes, Wes, We9, W71, W73, 75, W77, W80
| 5043-08980-00 | B | Otpf Cap., 10V, Axial |
| 5040-08986-00 | C1,C2,C5,C10 | 100 Cap., 10V, Axial |
5043-09845-00 C3, C4 10V, Axial 5041-09243.00 c6-c9 10V, Axial
| 5043-08996-00 | cH | Auf Cap, Axial |
| 5019-1261 1-00 | SR1,SR3,SR8, | 4700 SIP, 5 Res. |
SR, SA12, SR13, SRi8
| 5019-09362-00 | SA3,SR4,SR6, | 4.7KQSIP, 9 Res. |
SR7, SA11, SAIS, $R17, SR19, SR20, SR21, SR22, SR23, SR24, SRC1, SRC2, SRC3
| 5019-10143-00 | SRS | 4709 SIP, 9 Res |
| 5060-10396-00 | SRC4, SACS, | 4.7KQ SIP, 470pf |
SRC10, SRC14, SRC16 2-3
A-14732-40025
Sound Board Assembly
EE raz} HSS oy . 5} <3
@N lop lca + ao Ninel yao a i>} low oo ps.
°
2? Se
°
Part Number
5340-12958-00 5340-12959-00 5281-09850-00 5281-09215-00 5281-09851-00 5281-09487-00 5281-09745-00 5281-09246-00 5281-09733-00 5281-09486-00 5340-12278-00 5370-12260-00 5460-12743-00 5370-12960-00 5370-12730-00 5371-12727-00 5370-12963-00 5521-10931-00 5520-09020-00 5010-09534-00 5010-12961-00 5010-09039-00 5010-10170-00 5010-09036-00 5010-09187-00 5010-09160-00 5010-09416-00 5010-09358-00 5010-08998-00
5010-08983-00 5010-10000-00 5010-08991-00
5010-09219-00 5010-09034-00
5010-09269-00 5010-09924-00 5010-09325-00 5010-09035-00 5010-10987-00 5010-10650-00 5010-08776-00 5010-10257-00 5010-12927-00 5010-09162-00
5010-12965-00 5010-09134-00 5010-12964-00 5048-11027-00 5043-10264-00 5043-09492-00
5048-12748-00 5048-11030-00 5048-12506-00 5048-14031-00 5048-11065-00 5048-12967-00 5048-11072-00 5048-12966-00 5043-08980-00
5045-12926-00 5043-08996-00 5048-12036-00 5040-09365-00 5040-09343-00
5040-09332-00 Designator
U7, U11, U24 Us, U10, U25 u19
u21 U9, U22, U23 us u20 u17 U5, U16 U2 U30 VRt u29 U32, U33 UIs u31 Y2 vt W2, W3, WS,W7, WB R72-R74 Reg R11-R21 Ra, R30, R90 R27 R83 R32, R43, R41, RBZ R43, Res R22-R24, R26, R59, Ret R28 R87 R1-R3, R5-R10, R25, Re4-Ra6, R91 R69 Re2, R63, R67, R70, R80 Rea Res R36 R29, R53, R81 R77, R78 R38, R45, R51 R31, R71 R35 R79 R33, R48, R54, RSS, Reo, Res R39 Rao, R44, R46, R52 R97, Ra2 C59, C60 C50, C62 C35-C45, C47, C49, C98 C54, C61, C96 crt c7e C48,C55, C76 Cea C58 C51, C56 C52 €2.C26, C28, C29, €31-C33, C97, C99 C90-C92 C72, C74, C88, C89 ces ces C46, C53, C57, C64, 67073, C75, C81, €100, C102 C63, C66, CBO A-14732-40025
Sound Board Parts
Description
IC, 261831 IC, 261832 1C, 74L811 IC, 74LS04 IC, 74L914 Ic, 74LS74 Ic, 2418138 IC, 74.8139 IC, 74L8174 IC, 74L8374 IC, Static RAM, 8K x 8 IC, 3340 Attenuator IC, 7809 Regulator, +9V IC, LM324 Op Amp IC, TLO84 Op Amp AD7524 DAC HA13116 Pwr. Amp &Mhz Oscillator 3.58 Mhz Crystal 09 Resistor 3.39 Res., 5%, 1/2W 100 Res., 5%, 1/4W. 470 Res., 5%, 1/4W 1002 Res., 5%, 1/4W 15002 Res., 5%, 1/4W 2209 Res., 8%, 1/4W 4700 Res., 5%, 1/4W 1KQ Res., 5%, 1/4W 2.2KQ Res., 5%, 1/4W
3.3KQ Res., 5%, 1/4W » 5%, /4W 1 5%, AW
B.2KO Res., 5%, 1/4W OKA Res., 5%, /4W
12KQ Res., 5%, 1/4W 27KQ Res., 5%, 1/4W 39KQ Res., 5%, 1/4W 47KQ Res., 5%, 1/4W. 56KQ Res., 5%, 1/4W 62KQ Res., 5%, 1/4W. 68KQ Res., 5%, 1/4W. 75KQ Res., 5%, /4W 82KQ Res., 5%, 1/4W. 100KQ Res., 5%, 1/4W
130KQ Res., 5%, 1/4W 150KQ Res., 5%, 1/4W 820KQ Res., 5%, 1/4W 33pI Cap., 10% 88pf Cap., 10% 100pt Cap., 10%
220pf Cap., 10% 470pf Cap., 10% 820pf Cap., 10% 1000pf Cap., 10% 2200pf Cap., 10% 2700pt Cap,, 10% 3300pf Cap., 10% 3900pf Cap., 10% Oty Cap., 10%
tut Cap., 10% tf Cap., 20% 22yf Cap., 10% suf Cap., 10pt Cap., 16V, 20%
47 pi Cap., 25V Part Number
5040-09421-00 5040-09506-00 5040-12670-00 5070-08919-00 5160-12891-00 5551-09822-00 §700-09006-00 5700-09915-00 5700-09004-00 5700-08985-00 5700-12088-00 5791-10862-04 5791-10862-06 §791-09437-00 01-40516 4406-01128-00 4006-01003-06 20-9690-18 A-5343-40025-19 5400-10320-00 A-5343-40025-20 A-5343-40025-21 5370-11086-00 A-5346-40025-9 5371-11087-00 5433-12962-00 03-8338-1 Designator
C70, C85-C87, C103 C79, Ca, CB4 C95 cri Qi 1, L2 u28 Ura ura ua U3, U12, U13 PS, P7 P6 Pt
U3. U4 ui2 U13 uta u18
ut Description
100pf Cap,, 25V 220uf Cap., 16V 2200yf Cap., 16V 1N4148 Diode MPS3646 Trans. 4.74H Inductor, 3A 16-pin Socket
40-pin Socket 32-pin Socket 4-pin Header 6-pin Header 20-pin Header Heat Sink 6-32 Hex Nut 6-32 x 3/8 P-PH-S Spacer, 1-1/8 IC, EPROM IC, 68B09E, MPU IC, EPROM IC, EPROM IC, YM2151 Sound Generator IC, PLD Sound 4C, YM3012 DAC IC, OKI6295, 4 Channel Mig. Spacer, 1/4"
MORTAL KOMBAT
SECTION three
Schematics and Wiring Diagrams
Ado Uo zr OL Funetion JAMMA Chart
| WireColor | Pin | Pin | WireColor_Function | ||
| | Ground | Black | 1 | A | Black | Ground | |
| [Ground — | Green-Drown | | Black | Ground — | ||
| [+5 Volts DC | 2 | ct | Gra | #5 Volis DC | |
| | +5 Volts DC | Gray | 4 | DT | Gra | +5 VolisDC | |
| 5 Volts DC | Gray-Grean | {5 | [ET | Gray-Green |S Volts DC | |
| +12 Volts DC | Gray-Yellow | 6 | FT | Gray-Yellow | +12 Volts DC | ||
| Kay | L | ~H | Kay | ||
| Counters = | White-Orange | 8 | | wnite-Green |" Counter2> | | | ||
| Ni | 2 | K | NC | ||
| |_ Speaker (+) | Red-Violet | 10. | L | Green-Violet | Speaker (-) |
| mal | M | NIC | |||
| | Video Red | 12 |" NI | Green’ | dao Grn | _| | |
| [ Video Blue | 1a | pT | White | Vi | ||
| | Video Grd | 14_|R | White-Red | avi | : | ||
| - | 15_|_s_T | white-Violet | "Siam Tit” | |||
| 1 Cain. | 16 | 1 | Yallow-Whita | _2 Coin | ||
| }1 Start. | 17 | | | Yellow-Blue | 2 Start | |
| | 4 Up | {ag | yt Yaliow-Black | 2 Up | | | ||
| 1 Down | Qrangs-Brown |_19 | W__|_Yellow-Brown | 2 Down | |||
| iteft | Orange-Red | 20 | xX | Yellow-Red | 2teft |
| }1 Right | Orange | 24 | Y__|_Yellow-Orange | 2 Right | ||
| High Punch | Orange-Yellow| | 22 | Z| | Yollow-Violot_|_2 High Punch | ||
| 1 Block | Orange-Green | _ 23 | rt | Yallow-« | 2 Block | |
| 41 High Kick | Orange-Biue | 24 | b | Violet-Brack | 2 High Kick |
| NC | 25 | eT | NC | NIC. | |
| [wc | NC | ge | gd | Te | NC |
| |_ Ground | NIC | 27 | @ | Ni | Ground |
| Ground | Black | 28 | t | Black | Ground |
- Optional Switches
Interboard Wiring Diagram
al a. HH 2 E| a3 | | EREER é 654321 3
| Pi | PG | = | Le | 8 |
Ribbon Cable Power From ps | --}osanoaaibite 2
| To CPUJ8 | J2 | el | 4 |
CPU. 7 een ita 8
| Violet! | wa | 8 | ||
| Nill o | ‘Sound Board | e | ||
| NIG}} n> | P7 | _ | oy | ||
| —Blue|| ~ | g§ | co | sin | |
| 2L) | 3 | gs | ||
| az} | 3. | g | ee) | eek |
q Fara
| a4] | ole | &| | 86] | § | 38 |
¢| 3 B18 | [8
| q | i | | ol | Sloe | olee |
ag] 83 ae
| JAMMA Edge Connector | Saqaisiag | BERBER EERE |
H
| Crettsed] | ‘Seo vANMA Chan | LI—1__jft23456 | 123456789 10111 |
v2 4
| IK | Power to Sound | To Control Panel |
3] 2 Board P6 ig) 5
Y-Unit CPU Board g
| YA | 198 | From P1 On Sound Board | a | ws |
| [[NerUser | a) | Not Used | Noi Used |
L
CPU BOARD 7] Ja
Typical Cabinet Wiring Diagram
- Red Line on Ribbon Cable must go to Pin -1 on both boacds. Ribbon Cable may need to be twisted to accomplish this.
"20 Pin Ribbon Cable
J2 H14925 ‘Sound/Power Speaker Cable Pt psy P7 3 To
Volume Control
Orange-White [GreenWhite %
Saoenonal ua Pe
‘Sound
Board
Ground “Red-Brown Low Kick 1
NIG Red Low Punch 2 (H-15874 Auxiliary Cable To J4on CPU Board H-15873 Adapter Cable for STREET FIGHTER I {; |To JST type connector ick. 2 Jon contro! panel cable
Violet 3
Low Block 2 Red-Black. Red:Brown. Low Punch 1 ‘Low Kick 1 ped Low Punch 2 To Red-Orange _Low Kick 2 Control Panel
[A Black ‘Ground —Biach___Ground
10. é im fa < = = Es Shielded Video Cable Video Composite ral _All Black Wires. Res-Vi /,Green-Vioiet To Speakers To Coin Door To Power Supply
Ground {Quantity 5)_ SV {Quantity 2; Not Used)
Y/ All Green-Gray Wires
H-13411 Main JAMMA Cable Yellow-Green Stat ‘Orange-Brown Joystick Dowa ‘Oranga-Red Joystick Leit To Control Panel Player 1
Orange-Blue___High Kick Oranga-Violet_ Not Used a ~ Ground /Yellow-Biack Joystick Up Yeliow-Brown Joystick Down. Joystick Left To Control Panel Player 2
- |
Coin Switch and Meter Wiring
Option 1
+5V
Meter
JAMMA Pin 16
JAMMA Pin 8
Option 2 Coin Sw 1
JAMMA Pin 16
Coin Sw 2 ——_» JAMMA Pin T JAMMA Pin8
Wrong Way ! it 1 Coin Sw JAMMA Pin T
JAMMA Pin 16
Do NOT Connect the coin switches this way. This Circuit is INCORRECT and will cause twice as many Credits per coin.
3-4
SDMA OOK,
CPU Sheet 1 of 16 vas. TH534010 Reser TORHDE i - 7 7 OSPR HLLACK,
3-5 LOCAL ADDR/BATA BUS Tawny AAAA
a she viva OTA
ver sng Bage TwoeT 9b 10 % JeauS
Ndo 3-6
“ssa vw € y0UuS <SSETW OTO Ndd STL ACELI OD
3-7
3-8 9L JO » JeaUS
Ndd
3-9 CPU Sheet 5 of 16 PROGRAM MEWORY Lorat eaTa Hus
vss, YeNTRETL
hate -baIvERa cork ona
3-10 CPU Sheet 6 of 16 Loca ADDR/ORTA BUS meas =OMA_6Ox, (plage DATA gus ete choca ADD BUS wa. co Hull NNONA PA 4
CPU Sheet 7 of 16 IwaCE DATA 8US.
3-11 IMAct ADDR BUS > es eee es >
Tate. Tange)
<a S08 vied va¥Riy
a) ‘sng s53uadv JO¥mT AwONIN 39¥HT
3-12 9b 40 8 1890S
Ndd
‘She Ssuu0oy Ov QL 40 6 180US Ndo 3-13
3-14 TA Te Qt 40 OL J80US
Ndo SITS HT OTST
CPU Sheet 11 of 16 uate Anon pus cepts ci ) L
3-15 roe TROL OK
- ISCLh COX
CPU Sheet 12 of 16 oor cK oBsecT PaLETT eve 9s
CPU Sheet 13 of 16
3-17
CPU
CPU Sheet 15 of 16
3-19 co sine
CPU Sheet 16 of 16
3-20 THT iL TT]
ii
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Sound Board
Sheet 2 of 4
Oo
On
a a.
bv 40 € JeEYS
pieog punos
SET] exes cay OF
~ 7
Vv a)
wo
Co a cz
wre
Sound Board
Sheet 4 of 4
Control Panel Wire Colors
Player One Start Up (Jump) Down (Duck) Left (Move) Right (Move) High Punch Block High Kick Low Punch Low Kick Ground
Player Two Start Up (Jump) Down (Duck) Left (Move) Right (Move) High Punch Block High Kick Low Punch Low Kick Ground Yellow-Green Orange-Black Orange-Brown Orange-Red Orange Orange-Yellow Orange-Green Orange-Blue Red-Black Red-Brown Black
Yellow-Blue Yellow-Black Yellow-Brown Yellow-Red Yellow-Orange Yellow-Violet Yellow-Gray Violet-Black Red Red-Orange Black
PC Board Jumpers
CPU Board We, W8, W11, W12, W14, Wei, W22, W24, W27, W29, W30, W32, W34, W36, W39, W41, W42, W45, W47, W48, WS50, W52, W55, W57, W58, W60, W62, W65, W68, W69, W71, W73, W75, W77, W80
Sound Board We, W3, W5, W7, W8
WARNINGS & NOTICES
- For safety and reliability, substitute parts and modifications are not recommended.
- Substitute parts or modifications may void FCC type acceptance.
- This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal under Federal law. This also applies to MIDWAY logos, designs, publications and assemblies. Moreover, facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with MIDWAY components.
Notice When MIDWAY ships a game, it is in compliance with FCC regulations. Your sticker is proof. If the sticker is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game does not contain an FCC sticker, call MIDWAY immediately.
Notice No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.
Entire contents of this manual copyright © 1992 MIDWAY Manufacturing Company, INC. All Rights Reserved.
FOR SERVICE: CALL YOUR AUTHORIZED MIDWAY DISTRIBUTOR.
MIDWAY Manufacturing Company
3401 N. CALIFORNIA AVE. CHICAGO, IL 60618