CATHODE RAY TOMES

Sky Shark

Flying Shark (World) (Toaplan / Taito Corporation, 1987) · Manual · 14 pages · 14 sections · original scan

Page 1

ROMSTAR ‘inc.

SHARK”

Instruction Manual

rolftar, Inc 3043 Kashiwa Street, Torrance, CA 90505, Phone (213) 5392744 Fax (213) 539-3626 Telex 182426

Licensed From Taito America Corp. All Rights Reserved ©1987

Page 2

Installing and Servicing Your

SKY SHARK

New Game Package

Table of Contents

New Game Package ContentS...... 0.6.6 c cece eee ee eee 2

Power and Monitor Requirements ...... 0.06 e cece eee eee eee ees 2

Recommended Tools and Supplies... 0.0... 0... c eee cece eee 3

Dip Switch Tables 2.0.0... ccc cece eee tenet tenn n eee 3&4

. Game Operation .. 0.6.06. n eee nent ene 5

  • Installation Procedures 2.1... 0... ccc eee eee teen nett eens 6

Control Panel Positioning ....... 0.66 e cece cece tence eee een ees 1

TECH TIPS 26 55st ieee see nt ee cn et noo bie re RESET R Toot ecu neem enone 12-13

Main Harness Connections .. 2... eee eect eee eee outside back cover

Page 3

oy NEW GAME PACKAGE CONTENTS

1 Main Printed Circuit Board (PCB) | Marquee 1 Monitor Bezel 1 Control Panel Overlay 1 Set Legs, Bolts, & Spacers 1 Plex Control Cover 1 Connecting Wire Harness 1 Set Side Graphics 1 Eight-Way Joystick 1 Set Play Instructions & Function Labels 6 Player Button Assemblies 1 Service and Installation Manual

Note: Replacement accessories availabie through your exclusive Romstar distributor.

POWER REQUIREMENTS MONITOR REQUIREMENTS

+5 VDC 7 amp minimum Verticle Mount Raster Scan lamp minimum Negative Composite Sync

Page 4

Before You Get Started. . .S5top/

Does your new game package include all listed parts? (Is it complete?) Is the game you have chosen to transform able to supply all the required voltages for the new game?

Note: Some games, (i.e. Ms. Pac Man, Galaxian, etc.) regulate their voltages on the main PC.B. This makes the existing power supply inefficient. These games will require a change in power supply for your new game. Many game supply houses can offer you a switching regulated power supply for a relatively low cost. !s the monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
  • Do you have the necessary tools? (See the recommended tool list)

Caution

F.C.C. Regulation Compliance Operation of this equipment in a residential area is likely to cause interference

  • in which case, the user at his own expense, will be required to take whatever measures may be required to correct the interference.

Recommended Tccls and Supplies

ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32" © 1/4” © 7/16” Drill Bits 1/4” Plex Bit 1-3/16” Chassis or Sheet Metal Punch 1 1/4” Plex Hole Saw Glass of Water and a Snack Small File Razor Knife and Sharp Blades Straight Edge Patience Common Sense

Dip Switch Tables

Optimize Your Profits Painting Supplies (if you do your own painting) Paint Brush and Paint (don't forget the primer) Paint Roller and Pan Sand Paper Putty Knife and Wood Putty A Good Night’ Sleep Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32" © 1/8” © 3/16” Masking Tape 3 112" OR 4" Wire Ties Spray Window Cleaner and Rags (baby diapers work GREAT!)

Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. If games aren’t running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.} It’s easy!

Page 5

Dip Switch 1 Sky Shark Dip Switch Settings

Table Upright *

Monitor Normal

Game Style

Flip Test Normal Game Test Mode Attract Sound on *

off -Coin 1-Play Coin!

Dip Switch 2

Difficulty

Bonus Level 50,000 - 150,000 70,000 - 200,000 50,000 Only 100,000 Only Number of Planes 3

Dip switch Test Normal Test

Continue Play

  • Denotes Recommended Settings
Page 6

—__ Game Operation

1000 BONUS POINTS AWARDED FOR DESTROYING ENTIRE YELLOW FIGHTER SQUADRON.

WHEN ENTIRE RED SQUADRON DESTROYED,

  • APPEARS
  • INCREASES FIREPOWER WHEN PICKED UP

WHEN ENTIRE BLUE SQUADRON DESTROYED,

  • APPEARS
  • EXTRA PLANE AWARDED WHEN PICKED UP

1 EXTRA BOMB AWARDED FOR EACH PICKED UP.

Page 7

Installation Procedures

Something To Think About

Your final product will be a new game. You have made a wise decision to transform a game that has seen better days in the all important cash box into anew game. This is by far the most Cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that’s it! We provide the rest. The end resultis ... anew game ata

very low cost. Fact: Spend a little time on the cabinet’s appearance (i.e. marquee, control panel and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game. . .especially with the introduction of anew game package. The new game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner willen- . sure that unnecessary glitches do not occur. .

Remember: You are creating anew game . If you have any questions or just need some advice on any of yournew game transformations, don’t hesitate in giving a member of our technical staff a call.

Let’s Get Our Hands Dirty

Preparing the Original Game for the New Game

Remove the following:

1.Main logic board(s)4.Monitor Bezel
2.Control panel5.Marquee-
3.Monitor plexiglass6.Graphics

| would recommend painting your cabinet to give it a fresh new look. You may consider having an auto body shop take care of your painting needs.

If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.

Page 8

Time To install Your New Goodies

Before You Start. . .Remember DO NOT Do This Work With The Power Onl

Logic PC.8. Cage

Mount the logic board securely (away from power supply). A Mark and drill pilot holes (3.32”). B Install the P.C.B. into cabinet. Use feet and spacers supplied and adjust them so that the screws will go through the holes in the cabinet.

Wire Harness

Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.

Connecting the Wire Harness to the Existing Wires When you hook up the control panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors.

  • Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
  • Solder the new wire designated for that position to the original wire you just stripped.
Warning: DO NOT JUST TIE THE WIRES TOGETHER. THIS CAN CAUSE NAGGING INTERMITTENT PROBLEMS THROUGH LOOSE CONNECTIONS OR OXIDATION OR BOTH. Always take the time to do It right.
  • Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
  • Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a new game , not a sloppy conversion.

Power Wires

  • Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
  • You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don't overload the edge connector pins and cause them to “burn”.
Page 9

Monitor Wires You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.

NOTE. . .CONCERNING SYNC: Your new game only calls for one sync wire connection, this is called composite syne (horizontal and vertical tied together). This composite sync is also negative. Most monitors have supply positions for both negative and positive sync. You can check your monitor manual or cail our technical department for assistance.

Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.

Coin Door Wires Connect the designated wires to the coin switches and meter. (See tech tips}

  • Youcanconnect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
  • Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.

GUESS WHAT?

You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.

Smoke Test

What Test?

Don't worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.

  • Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
  • Make sure the logic board, monitor and power supply are securely fastened in place.
  • Double check the connectors to be sure they are wired and connected properly.
  • Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.) Also, be sure you set the dip switches for “DEMO WITH SOUND”. This will enable you to hear as well as see that your new P.C.B. is functional.
Page 10

Time to Apply Power:

  • Look and smell for smoke. [TURN OFF IMMEDIATELY IF ANY IS NOTICED)
  • Listen for game sounds. If after one minute you have not heard any sounds A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections C) Check the +12V power supply to the logic board
NOTE: If you do get sounds, but they are alittle fuzzy, switch the wires around on the speaker.
  • How is the monitor image? A| Is the picture in sync? if your picture has the top and bottom halves of the screen reversed and it will not stop rolling, change your sync polarity on the monitor. (Positive to negative (see tech tips section).

NOTES:

B) Now how’s your picture? © It it centered? # Is it too bright or dim? Is it in focus? Check your monitor manual for these adjustments. If your screen looks “off”, then your new game transformation may have been in vain. So let’s take the time to make the monitor look great. C} Is the picture upside-down? Refer to your monitor manual - switch two horizontal yoke wires and then switch two vertical wires. (Pull the pins in the connector on the monitor P.C.B. to switch them.) or check Dip Switch Tables

Page 11

Controi Pane! Assembly

  • Remove the buttons, joysticks and wire harness and put them aside for now. Do not remove the original panel overlay until the new holes have been drilled.
  • Mark positions on the panel for the new holes. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We feel that your new game investment is well worth protecting. . .and the control panel is the first place to show wear and tear. *® You will need to cut this piece to size. Use the control panel as a template. © Use arazor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass.
  • Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes.
  • Drill the same holes on your plexiglass pane! protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hoie cutter.
  • The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file.
  • Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Vo bubbles please. Now peel off the bottom half and do the same as you did for the top.
  • Adhere the instruction and function labels.
  • Install the Plex Control Cover over your completed new game panel.
Note: Be sure to bolt the plexiglass securely to the panel.
  • Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible}

Marquee Installation

Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers.

Note: when cutting marquee to size, check to make sure that you are cutting as ~ little of the necessary art as possible (name, manufacturer, etc.)

Be sure the light behind the marquee works. Everything should always work

on a new game. Take your time ... Don’t forget this is going to be a new game.

Page 12

Side Graphic Instailation

Be sure sides of game are clean and free of old adhesive, dust, etc.

  • Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet).
  • Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag}. Continue peeling off backing and smoothing.
  • Remove any small bubbles with a pin or razor blade (pop them!)

Finishing Touches

  • Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware. 2, Make sure the coin door is tight and the coin mechs are well adjusted. A game is No good to anybody if you can't get a COIN Into It.
  • Once again go over every step of thismew game transformation in your mind. Be sure everything is correct and to your liking.
  • Power up the game. A. Check all the coin:switches. (Does the coin meter work?) B. Play your new game - Are all the player controls working? Are the game sounds present? Is the volume level proper? Are the dip switches set properly? Well, that’s about it. Good Luck.

8 WAY JOYSTICK BOMB FIRE | FIRE BOMB ad ee

POSSIBLE 1 & 2 PLAYER LOCATIONS

Control Panel Positions

Page 13

Star Tech Tips We are grateful to Star Tech Journal for allowing us to publish the following excerpts from their journal.

  • Monitor Sync Ifyour monitor does not have dual polarity positions for sync, you may use one of the following methods to get your game going. CURE 1: Install a simple one I.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two power pins so that they are parallel to the top surface of the new I.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup for either composite or separate syncs.) *, HORIZONTAL SYNC INPUT FROM P.C.B. 5 Vcc $voc (PIN 14} (OR COMPOSITE SYNC INPUT) ~ SOLDER TO. HORIZONTAL SYNC OUTPUT TO MONITOR EXISTING CHIP. {OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC INPUT FROM P.C.B

VERTICAL SYNC OUTPUT TO MONITOR |

FIG. 2

CURE 2: Used for Wells-Gardner Video-Sync boards with positive sync connections only. (Vertical mount board 85x140B.

Cut the traces on the solder side of the board between input pins 5 & 6to the unbanded (anode) ends of diodes X201 & X202. Add MPSAS6 transistor as follows: Collector to anode leads of diodes X201 & X202. Base to pins 5 & 6 of the video input connector. Emitter to cathode (banded) lead of zener diode ZD201. Insert a IN4148 diode - cathode to the emitter of the MPSA56 and anode to the base. (See Fig. 3} RED! GREEN 2 BLUE 3 GND 4 FIG. 3 VERT. 5 HORIZ 6 MPSAS6. 0000 IN4148

CUTTRACES

12 X201

Page 14
  • Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GC7-CBC moniter negative sync inputs. The result of this mismatch is a Forizontal “wave” or “curl”. CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radial lead capacitor with the positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap remeved from the C303 location. CURE 2: Connect 1N4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. (See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability.

INS148

NEG: SYNC INPUT

vO} GND —~ Ss FIG. 4 ' GND BLUE «GREEN RED

  • —- SST ot 1D _Ov_O e) (e) O} 6 5 4 2 1

IN4148

CURE 3: Join negative sync inputs J2 and J3 together with a jumper. Locate W102 and install a jumper from \W/102 to either J2 or J3.

CURE 3: For Wells-Gardner K4600 series monitors Replace C356 (4 7uf 25V) on the Horizontal vertical board (vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune with the horizontal width pot.