American Horse
American Horseshoes (US) (Taito America Corporation, 1990) · Manual · 13 pages · 10 sections · original scan
TAITO. AMERICA Soemoeumon: 390 Holbrook Drive Wheeling, |I. 60090 Telephone (708) 520-9280 Fox (708) 520-1309 Part No. .285-200701
TABLE OF CONTENTS
Play Instructions, Scoring... 2... ee ee ee page 1
General Information... 2.2... 6 ee ee ee eee pages 2, 3
Cabinet Selection ©... 2.2... ee ee ee ee page 4
Game preparation and Conversion... ......... pages 5, 6
Dip Switch Settings .. 2... 2. eee eee page 7
Control Panel Assembly... 2... 2... 2. eee page 8
Control Panel Cutting Guide... 2... ee ee page 9
Connection Chart... 6. ee eee page 10
Kit Parts List... 2... ee ee ee ee eee page 11
- ATTENTION +
THE COPYRIGHTED VIDEO GAME THAT ACCOMPANIES THIS MANUAL CARRIES WITH IT A ROYALTY FREE, NON-EXCLUSIVE LICENSE FROM THE COPYRIGHT OWNER TO THE OWNER OF THE VIDEO GAME TO PUBLICLY PERFORM THE COPYRIGHTED VIDEO GAME IN THE UNITED STATES OF AMERICA, CANADA, AND MEXICO. THIS PUBLIC PERFORMANCE LISCENSE ATTACHES AND APPLIES ONLY TO THE PHYSICAL EMBODIMENT OF THE VIDEO GAME THAT ACCOMPANIES THIS MANUAL. THIS PUBLIC PERFORMANCE LISCENSE MAY ONLY BE TRANSFERRED TO THE SUBSEQUENT OWNER(S) OF THE PHYSICAL EMBODIMENT OF THE VIDEO GAME THAT ACCOMPANIES THIS MANUAL.
O
O
O Play Instructions:
Use the trackball to select the player mode and the character of each player. Up to four players can join in.
Two-button mode (dip switch selectable)
Use the "Grip Select” button to choose or change the style of holding the horseshoe.
Use the "Angle Select” button to choose or change the throwing angle. (Hint: it’s fun to experiment)
One—button mode (dip switch selectable)
Press the “Select” button once to choose or change the style of holding the horseshoe. Press the “Select” button again to choose or change the throwing angle.
hrowing the shoe
Use the trackball to position the piayer, aim the shoe, and control the distance of the throw. Left ~ right motions on the trackball move the player laterally. Roll the trackball with a brisk motion in the direction you want the shoe to fly in. The speed of the trackball controls the distance of the flight. Each player gets two throws per turn.
Scoring
3 points for a ringer 2 points for resting against the stake 1 point when in the box
The scoring process is shown from an overhead viewpoint and shows where each shoe landed, in succession, and the points awarded each. The scoring process speed may be changed by a dipswitch setting. Missed or overthrown horseshoes can result in amusing accidents, try a few...
oOo 39 39 39 9 90
GENERAL INFORMATION
This manual will guide you in the conversion of your color monitor upright video game into an Am.Shoesgame. We strongly urge you to read through the instructions carefully before beginning the conversion.
WARNINGS AND NOTICES
For safety and reliability, Taito America Corporation does not recommend nor authorize any substitute parts or modifications of Talto America Corporation equipment. in addition, any substitute parts or equiptment modifications may void FCC compliance.
Use of non—Taito America parts and/or modifications of game circultry may adversely affect game performance and safety.
Since American Horseshoes Is protected by Federal copyright, trademark and patent laws, unauthorized aitered versions of this game are illegal under Federal law. This also applies to unauthorized facsimilies of Taito America equipment, logos, designs, publications, assemblies and/or games (or features not deemed to be in the public domain) whether manufactured with Taito America components or not.
NOTICE
Certain parts salvaged from your old game are required to complete your kit. These salvaged parts MUST operate properly to Insure the performance and safety level of this game. Always repair electronics malfunctions and cabinet damage before conversion Is attempted. Be sure the power supply from your old game is capable of delivering +5 vde at 7 amps, ~Svde at 1A, and +12vde at 1A. These operating voltages must be regulated and are necessary for your kit. Please note the enclosed warning with the PC board assembly.
Check the parts supplied in this kit against the parts list included in this manual.
This kit is not intended for use with X-Y (vector) monitors. Suitable monitors are vertical raster—scan RGB types with composite negative sync. The monitor must be connected to the A.C. line through an Isolation transformer.
FOR SAFE OPERATION IT IS STRONGLY RECOMMENDED THAT THE CABINET BE PROPERLY GROUNDED. IF YOUR GAME IS EQUIPPED WITH A THREE CONDUCTOR POWER CABLE, THE THIRD PRONG (round) SHOULD AUTOMATICALLY GROUND THE GAME WHEN PLUGGED INTO A PROPERLY GROUNDED THREE PRONG RECEPTACLE. IF 1T BECOMES NECESSARY TO USE AN ADAPTER, THE GROUNDING LUG OR WIRE ON THE ADAPTER MUST BE PROPERLY GROUNDED TO ASSURE SAFE OPERATION.
QO TRACKBA N at N.
Cabinet Side Decal Application:
Use a dishwashing detergent (i.e: “Joy”) to make a sudsy solution and apply to cabinet side. Peel off the backing of the side decal and apply to cabinet side. The soap solution makes it possible to reposition the decal while it is on the cabinet side. Squeegee excess soap solution out from the center of the decal. Professional kit~—builders have found that spraying the cabinet side with glass cleaner (i.e: "“Windex”) results in a quicker application, and that the decal can be squeegee’d into place easier if you work from the top down. RED ~ 2 WIRES, +5V
BLACK — 2 WIRES, GND. BLUE — UP
VIOLET — DOWN
YELLOW — L
GREEN — R
SIDE DECAL
mS
ABINET TION
INAPPROPRIATE CABINET STYLE
“American Horseshoes” has the players control the horseshoe throw with a long, sweeping motion of the hand. The sharp angle between the handboard and the monitor glass will cause the players to bang their fingers against the glass. APPROPRIATE CABINET STYLE
The monitor and handboard are coplanar or nearly so. This provides a clear path for player’s hand mations.
GAME. PREPARATION
All games require a certain amount of maintenance to remain in good operating condition. A periodic check of mechanical controls would be benificial to guarantee the profitability of your game.
CLEANING The exterior of the game, all metal parts and all plastic parts can be cleaned with a non—abrasve cleaner. Caution should be used when cleaning the plastic. A dry cloth can cause scratches and result In a foggy, worn appearance. Plexiglass cleaner on a soft cloth is suggested to keep your monitor ert cover looking new.
Inspect your cabinet for any gouges or items stuck on the cabinet (like chewing gum). Remove ail foreign objects and fill In the gouges with any type of quick—hardening wood putty. Sand to ensure a smooth surface. Wipe the outside of the old cabinet clean. Remember that the reason you are converting your old game is to have the increased earnings of a new game, and making your game LOOK new helps spark player interest.
NOTICE Please make sure you clean the coin mechanisms. It is important that you service them in order for this game to achieve the maximum possible earnings.
CONVERSION INSTRUCTIONS
GAME TITLE MARQUEE Remove the new “American Horseshoes” marquee from the kit. This new marquee is specifically designed for ease of handling. Place and center the old marquee on top of the new marquee. Border the area that you intend to cut with masking tape. Using an X-Acto or similar knife, score the new marquee and simply break at this score. If your old marquee is made of glass, remove the paint of the old marquee and attach the new marquee behind this glass. If your old marquee is made of Plexiglass, it is recommended that a new, clear plexiglass panel be used to show the American Horseshoes marquee sharply. MONITOR BEZEL
Remove the new American Horseshoes monitor bezel from the kit. Place the bezel oround the existing monitor. Using an X~Acto or utility knife, trim the new monitor bezel to neatly fit around the monitor,
CONTROL PANEL.
Remove the old control panel buttons, joystick(s) and panel overlay. Refer to the final page of this manual for the preferred positions for the joysticks, buttons and button labels.
Leave your 1 and 2 player start buttons where they are on the old control panel. Drill holes as needed for the installation of the joysticks and buttons. Clean any burrs from around holes. Any hole that is no longer needed we suggest plugging with wood putty or epoxy.
Cut the new American Horseshoes Lexan panel overlay to the appropriate size needed to cover the panel. Leave enough to wrap a small tip around the top and bottorn of the panel. Remove the backing from the American Horseshoes overlay and apply It over the old control panel, being careful to avoid air pockets.
After the Lexan overlay is securely applied, cut through to the holes in the contral panel with an X—Acto or utility knife. Install the trackball, buttons, button labels and any necessary hardware previously removed from the control panel. Tighten and secure all hardware.
INSTALLING WIRING HARNESS
This game comes with a color-coded cable for easy installation. Refer to the connection diagram included in this manual for quick hook~up.
Disconnect the old wiring harness from the old cpu board and carefully remove the old EMI shields and circuit boards from the game.
Using the wiring diagrams from your old game, carefully note the function of each wire. Cut the wires near the games coin door, monitor, control panel, power supply and speaker, leaving several inches of wire hanging from each point. Install the new wiring harness to those points referring to the connector diagram. For best results, solder directly to the lugs at the connection points and remove old wiring completely. Use electrical tape or heat—shrink tubing (preferred) to insulate any necessary wire splices. it is recommended that any wire splices be soldered; while an unsoldered twisted connection will work initially, non—conductive oxides will form on the wires that may cause fallure of the junction.
install the RFI “cage” (for FCC compliance) where the old board set was. Mount the Am. Shoes pcb assembly with mounting blocks In the center of the RFl cage. Plug the wiring harness onto the pcb and close the cage securely. To complete proper Installation, run a ground termination lead from any available chassis ground to the foil side of the RFI cage.
Check and clean the input Jack on the power supply board. Replace any burned or damaged pins.
oo
DIP_SWITCH SETTINGS
The following option switch settings were designed to allow the customizing of Am.Shoes’various game features to suit different environments. If used wisely to tailor a game’s features to suit the location, the flexibility they offer can maximise game performance and increase potential earnings. The dip settings are listed in the following chart —
“AMERICAN HORSESHOES” DIP SWITCH SETTINGS (UNITED STATES VERSION) DIP SWITCH — A: . SWITCH POSITIONS
| FUNCTIONS | SETTINGS | aN 1 | 2 | 3.4 | ~°=«5 | 6 | 7 | 8 |
E = BEER FRAME| "BREAK TIME” OFF
| MESSAGE | "BEER FRAME” | ON | |
| SCREEN | NORMAL | OFF | | |
ROTATION REVERSE ON
| TEST | r NORMAL GAME | OFF |
MODE TEST MODE ON al
ATTRACT WITH OFF
SOUNDS WiTHOUT
| PLAY | 1 COIN = 1 PLAY | OFF OFF |
| PRICING | 2 COINS = 7 PLAY | ON OFF |
3_COINS = 1 PLAY OFF ON |
| 4 COINS = 1 PLAY | ON ON | 1 |
| PRONG | SAME_AS ABOVE | OFF OFF. |
1_COIN = i CONT. ON OFF CONTINUED [3 GOINS = 1 CONT.
| PLAY | 3 COINS = 1 CONT. | “ON ON] |
DIP SWITCH ~ 8: L SWITCH POSITIONS
| FUNCTIONS | SETTINGS | 3 | 4 | «5 | 6 |
MODERATE OFF OFF
| pERCULTY | FaNSp | OW OFF | t |
(DIFFICULT OFF ON
| VERY DIFFICULT | ON ON | | | |
| 30_SEC. | OFF__OFF | | | | |
| TIMER | 20 SEC, | ON _OFF | ch |
40 SEC OFF ON i
| [60 SEC | ON __ON | il | _ | i |
| NUMBER OF | 3 | OFF | it | ||
| INNINGS | 3 | ON | | | |
| BONUS | “| OFF | OFF | | |
ADVANTAGE | ON ON
| SCORING | NORMAL | OFF |
| SPEED | FAST | ON |
GRIP/ANGLE | 2 BUTTONS OFF |
| SELECT | _[1 BUTTON | ON |
BOLD TYPE INDICATES FACTORY SETTINGS |
ANGLE SELECT TAG ere SELECT \ Bi , <p
TRACKBALL, TOP VIEW
TOWARD MONITOR
Assemble the handboard as shown. Use the layout on the following page as a cutting guide. The trackball should be oriented with the wiring through lower right side.
1 1se7 ao +
SUGGESTED HANDBOARD LAYOUT
1/8 — 7/32" [1 utr
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
PARTS LIST:
| t | “tT | t |
Qty. | Description Ref. No. Part No.
| 1 | PCB, Game Logic | 285~—100001 |
+
| 1 | Harness, Standard Jamma | 900-601001 |
T t
| 1 | RFI shield (for FCC regulations) | 900-800401 |
| 1 | Trackball Assembly | V soonaastoc |
a one
| 1 | Trackball Mounting Plate | 900-802600 | | |
| 1 | Ultimate Pushbutton, blue | g00-400003 *. |
—— +
| 1 | [Ultimate Pushbutton, red | 900~400001 | | |
| 1 | Button ID tag, "Grip Select” | 900~—201113 | |
| 1 | Button ID Tag,”Angle Select” | 900-201114 | | |
aan nentenntnefin
| 1 | Monitor bezel with artwork | 285-—200101 |
1 | Marquee with artwork 285-—200201
- os
| 1 | Control panel overlay | 285-200301 | | |
| + | 4. | —|— | |
| { | Kit Instruction manual | 285-—200701 | | |
hn
| 1 | Game instruction card | 285- 200501 |
tT
| ;2 | Cabinet Side Graphics | 285—200600 | |
| i | TT | a | | |
| 1 | Cain info Decal Set | 285-—200601 |
1 | Sign—up Pad . 285~200001 +. + 2 | Announcements 285-—200002
| 1 | Tournarnent Pad | L | 285-—-200003 | : |
TOOLS AND SUPPLIES RECOMMENDED [ ] Screwdriver, flathead Wire cutters Scredriver, Phillips X-Acto knife
[ ] Pliers Electric drill
Allen wrench set 1.125” drill bit (buttons) [ Grease pencil or marker 7/32” drill bit (trackball) | | Soldering iron and solder Router [ ] Hacksaw, Jigsaw or Tablesaw Sandpaper, 180 grit (with carbide~—tipped blade) Electrical tape or heat— shrink tubing