Sky Diver TM-117 1st Printing
Sky Diver (Atari, 1978) · Technical Manual · 122 pages · 48 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the label located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service. tee
Operation, Maintenance and Service Manual
ATARI INC 1265 BORREGAS AVENUE PO. BOX 9027 SUNNYVALE. CALIFORNIA 94086 408/745-2066 * TELEX 35-7488
A,
ATARI
A Warner Communications Company QD
li Skydiver Copyright © 1978 by Atari, inc. All rights reserved
Motorola and TEC service manuals reprinted by permission of Motorola Data Products and TEC Videoelectronics, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of aphonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permissions request, write:
ATARI INC 1265 Borregas Avenue P.O.Box 9027 Sunnyvale, California 94086
6a
Lithographed in the U.S.A
TABLE OF CONTENTS
LOCATION SETUP A. INTRODUCTION .... er res £43 ebaaee & B. GAME INSPECTION ................055 C._ INSTALLATION REQUIREMENTS ..... Power Requirements ... sees Temperature Range “ Humidity 2.60.00... 00.0000 e ee eee veces Location Space Requirements .................005- Type of Power Cord . INTERLOCK AND POWER ON/OFF SWITCHES . OPERATOR OPTIONS .. SELF-TEST PROCEDURE VOLUME CONTROL... amms
GAME PLAY A. ATTRACTMODE...... 200.200.0000 ree ve 1B B, READY-TO-PLAY MODE ... veces coves . C. PLAYMODE «0.6... veer 14
MAINTENANCE AND ADJUSTMENTS A. CLEANING...........0000000005 B. COIN MECHANISM Components on Coin Door Access to Coin Mechanisms Cleaning ot Coin Paths. ...... . Lubrication....... Adjustment of Coin Switch Trip Wire FE) Mechanical Adjustments on Coin Mechanism ... 20 Genera! Troubleshooting Hints .. 20 C. FUSE REPLACEMENT wee wees ena 22 D. TVMONITOR ADJUSTMENTS . . ar 7 eh RES Ee ae . 22 E. TVMONITOR REMOVAL ............ wb it eee eae bene BB F. ATTRACTION BOARD AND LAMP. REMOVAL . + 23 G. LED START SWITCH REPLACEMENT............ fae ee eee . 23 H. RIPCORD CONTROL REPLACEMENT............ eee ecnigs cites oes 2B
THEORY OF OPERATION A. GENERAL INFORMATION ... . . 27
ILLUSTRATED PARTS CATALOG............ vee AT
Skydiver iii
TABLE OF CONTENTS
6 TV MONITOR SERVICING INFORMATION Motorola Service Manual A. GENERAL INFORMATION B. SERVICE NOTES. . Circuit Tracing . . Component Removal | . . CRT Replacement ............ : bees Adjustments....... wee qe OE LESTE S Eat LET EG Regulator Adjustment . bee eee eee Horizontal Hold/Oscillator Adjustment cones : Vertical Height/Linearity Adjustment . . . Focus Adjustment .......... Monitor Servicing............ C. THEORY OF OPERATON . Power Supply. .... +73 Volt Supply . Lee Video Amplifiers and Output. 7s D. HORIZONTAL DEFLECTION CIRCUITS. . oe Phase Detector................... fee ee Horizontal Oscillator... . Horizontal Pulse Shaper and Driver. Horizontal Output . Sync Circuits . . beeeeee Vertical Oscillator and Output. bees Blanking Amplifier. Sueee gee gee yee gig en
GENERAL oe SPECIFICATIONS .. Power Supply Input . Power Consumption. . . Video Input .... Picture Tube. . High Voltage. . : Horizontal Retrace Time . Resolution teks ee Scanning Frequency...... cea Tone Burst Amplifier ............ Environment............. @ >
iv Skydiver
Figure 1-1 Figure 1-2 Figure 1-3 Figure 14 Figure 1-5 Figure 2-1 Figure 2-2 Figure 2-3 Figure 24 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12 Figure 41 Figure 4-2 Figure 43 Figure 44 Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8 Figure 5-9 Figure 5-10 Figure 5-11 Figure 5-12 Figure 5-13 Figure 5-14 Figure 5-15 Figure 5-16 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-5 Location of Voltage-Changing Plugs on the Power dia Location Setup Requirements Location of Power On-Off and Interlock Switches. Location of RF Shield PCB Assembly . Location of Self-Test Switch and Volume Control . Attract Mode Ready-to-Play Mode Play Mode Ambulance Display Coin Door Assembly : Hinging Open the Magnet Gate Assembly Removal of Coin Mechanism Surfaces to Clean Inside of Coin Mechanism. Removal of Plate Covering Rear of Coin Slot Close-up View of Lubrication Point Detail View of Coin Switch and Trip Wire Coin Mechanism, Exploded View. . Locations of Adjustments on TV Chassis TV Monitor and Attraction Panel Removal LED Start Switch Replacement Rip Control Replacement Skydiver Game Block Diagram . Skydiver Schematic Diagram (6 sheets) Skydiver Harness Schematic Diagram Skydiver Type B Power Supply Schematic Final Assembly bees Cabinet Assembly Control Panel Assembly Attraction Lamp Board, Schematic and Assembly Attraction Lamp Board with Lamps Assembly TV Shelf Assembly . Coin Door Assembly Power Supply Assembly Rip Cord Assembly On/Off Switch Assembly Rectifier Board Assembly . . RF Shield PCB Assembly Skydiver PCB Assembly Front Bezel Assembly Coin Lockout Assembly Coin Switch Assembly Motorola Monitor Circuit Board in Service Position Motorola Monitor Block Diagram 73+ Volt Supply Circuit Motorola Monitor Vertical Drive Waveform Motorola Monitor Video Amplifiers and Output Circuit LIST OF ILLUSTRATIONS
v
LIST OF ILLUSTRATIONS
Figure 66 Motorola Monitor Horizontal Deflection Circuit. ...... Figure 6-7 — Motorola Monitor Horizontal Deflection Waveforms Figure 68 Motorola Monitor Horizontal Output Circuit . Figure 69 Motorola Monitor Sync Circuit . . Figure 6-10 Motorola Monitor Vertical Oscillator Circuit . Figure 6-11 Motorola Monitor Spot Killer Circuit Figure 6-12 Monitor Blanking Amplifier . . Figure 6-13 Motorola Monitor Chassis Rear View — Component Location figure 6-14 Motorola Monitor Circuit Board Detail — Solder View Figure 6-15 Motorola Monitor Schematic Diagram Figure 6-16 Motorola Monitor Circuit Board Detail —C ‘omponent Location . Figure 6-17 TEC Monitor Chassis, Rear View . . Figure 6-18 TEC Monitor Chassis, Top View Figure 6-19 TEC Monitor Printed Circuit Board, Top View Figure 6-20 TEC Monitor Schematic Diagram . Figure 6-21 TEC Monitor Wiring Diagram..............
LIST OF TABLES
vi Table 1-1 Operator Options Table 1-2 Extended Play and Bonuses - Table 1-3. Self-Test Procedure : Table 6-1 Motorola Monitor Electrical Specifications oe Table 6-2. Motorola Replacement Part Numbers Table 6-3 TEC Monitor Replacement Part Numbers eo}
LOCATION SETUP
A. INTRODUCTION Skydiver™ is a one- or two-player action game developed by Atari, Inc. The game is contained in an upright cabinet illustrated with brightly colored graphics to further enhance player appeal. A 23-inch TV monitor is mounted in the top front of the cabinet. The TV monitor viewing screen is shielded by a Plexiglas® panel that also displays graphics.
Player-operated controls are mounted directly below the TV monitor viewing screen on the front of the game cabinet. The controls consist of a rip cord control, a jump button and two LED switches labeled Black Player Start and Blue Player Start. A speaker mounted below the control panel provides the game sound.
The coin mechanism mounted on the front part of the cabinet below the control panel initiates the play. The cash box is located behind a locked access door to the coin mechanism:
The object of the Skydiver game is to successfully skydive from a traveling plane to a ground target that appears in a different position after each successful jump.
The player watches wind speed and direction using the blue or black wind socks. He or she must also judge target position, plane speed, duration of freefall before pulling the rip cord (to increase target score). Finally, the player must guide the man into the target using the rip cord control (left or right).
One or two players can simulate the action of skydiving using the authentic rip cord control. For a detailed description of game play refer to Chapter 2
B. GAME INSPECTION Your new Skydiver game is manufactured by Atari, Inc. and is ready to play immediately on removal from the shipping carton. Your cooperation is desired to supply the final touch of quality contro! to your game. Please follow the procedures below to ensure that your game is in perfect condition:
- Examine all external parts of the game cabinet for dents, chips, or broken parts.
- After determining that the game has been received in good condition, unlock and open the rear access door. Carefully inspect the interior and verify that:
@ All plug-in connectors are firmly seated
@ All integrated circuits in sockets on the game printed circuit board are firmly seated.
@ = The fuses are all seated in their holders.
@ No harness wires are disconnected
@ No loose foreign objects are present, especially metal objects that could cause electrical problems.
Be sure all major assemblies are checked. Check the game printed circuit board (PCB), the transformer, the two coin mechanisms, the speaker, the fluorescent light, and the player controls. Also, be sure the TV monitor is secure in its mounting.
Plexiglas® is a registered trademark of Rohm & Haas Company.
C. INSTALLATION
REQUIREMENTS
Power Requirements and Line Voltage Selection
Skydiver is shipped for operation at 110 VAC, 60 Hz. Power consumption is approximately 200 watts. However, if your local voltage is not 110 volts, follow this procedure. You must select one of four connectors at the power supply and plug it into the voltage selection socket. Figure 1-1 shows the four connectors with one of them plugged in. The plugs are identified by wire color as listed in this figure.
Location and storage should not be below 0 degrees Celsius (32 degrees Fahrenheit), and no higher than 49 degrees Celsius (120 degrees Fahrenheit).
Humidity Range
Relative humidity for location or storage should be no more than 95%.
Location Space Requirements
The Skydiver game requires a minimum of:
@ 169 centimeters (66 inches) of vertical clearance
@ 62 centimeters (25.5 inches) of width clearance
@ 69 centimeters (27 inches) of depth space
See Figure 1-2 for details.
LINE VOLTAGE-CHANGING VOLTAGE PLUG WIRE COLOR 95 VAC BLACK 110 VAC
210 VAC
®
ON/OFF AND. Cc INTERLOCK in SWITCH
C3 ts) Amp, 250 V. Slow - blow
8 Amp, 125V, Voltage - Change Plugs Slow - Blow
2.5 Amp .125 Vv. Slow — blow
Figure 1-1 Location of Voltage-Changing Plugs on the Power Supply
4° Skydiver 62 cm 69 cm (25% inches) {27 inches)
169 cm {66 inches)
Figure 1-2 Location Setup Requirements
INTERLOCK SWITCHES ON/OFF POWER SWITCH
Figure 1-3 Location of Power On/Off and Interlock Switches
Type of Power Cord
Atari has added a strain relief power cord to Skydiver. The advantage of this type of power cord is that, if pulled accidentally, the strain relief will hold the cord in place at the cabinet wall. The plastic strain relief “cushions” the impact of the shock and prevents the cord from pulling the wires out of the harness connector,
D. INTERLOCK AND POWER ON/OFF SWITCHES To minimize the hazard of electrical shock while you are working inside the game cabinet, an interlock switch has been installed at the rear access door. This switch removes all power from the game while the access door is open. To help you conserve energy, a power on/off switch has been installed on Skydiver so that the game can be turned off during closed periods. This switch is located at the top of the cabinet in a recess, as shown in Figure 1-3.
Check for proper operation of the rear access door interlock switch by performing the following steps:
- Unlock and open the rear access door.
- Plug the AC power cord into an AC power source outlet (wall plug).
3, Set the power on/off switch to the on position.
- Close the rear access door. Within thirty seconds the TV monitor should display a picture.
- Slowly open the rear access door until the picture on the TV monitor disappears. The picture should disappear when the rear door is opened less than one inch from the top.
- If the results of Step 5 are satisfactory, the interlock switches are operating properly. If the picture does not disappear as described, check to see if the appropriate switch is broken from its mounting or stuck in the on position.
- Close and lock the rear access door.
E. OPERATOR OPTIONS Skydiver game options offer maximum player appeal for each game location. These options are listed in Table 1-1. They are preset for a certain game setup during production. To determine how the switches have been set for your game, compare the TV monitor viewing screen during the attract mode with the information in Table 1-1. An additional method for determining these switch settings involves the self-test procedure. The self-test switch is located inside the cabinet, to the left of the coin door hinge, on the audio amplifier PCB. Set this switch to the on position. Compare the information on the TV monitor viewing screen during the self-test with the information in Table 1-1
To change the toggle positions of the switch assembly and set the desired options, the printed circuit board (PCB) must be removed according to the following procedure:
- Unplug the game. Unlock and open the lower rear access door.
- Locate the radio frequency (RF) shield assembly immediately inside the cabinet on the right. See Figure 1-4. On one end of the box is a printed circuit board (PCB) with an edge connector coming from the edge of the board.
- Turn the three quarter-turn fasteners on the RF Shield assembly by turning the wing nuts % turn.
- Carefully pull out the PCB and the RF shield board as one unit. These would not normally need to be separated when making option switch changes.
- Set the switches for the desired options, as shown in Table 1-1.
- Reinstall the PCB following steps 1 through 4 in reverse order. Do not force or bend the printed circuit board. Before reinstalling, always inspect the PCB for damage. Close and lock the rear access door.
- Plug in the game and verify option functions by playing it.
F. SELF-TEST PROCEDURE Skydiver will test itself and provide data to demonstrate that the game’s circuitry and controls are working properly. This procedure uses the TV monitor and the speakers; no additional equipment is required. See Figure 1-5 for location of the self-test switch.
To start the procedure over from the beginning, turn the switch off, then on again. This will return the test to Step 1 and can be done at any time during the procedure. See Table 1-1 for further details and instructions on the self-test. We suggest that you run the selftest procedure each time the coin box is emptied
G. VOLUME CONTROL If volume is incorrect for your location, open the coin door and adjust the volume control. See Figure 1-5 for location of volume control
RF SHIELD PCB
SKYDIVER GAME PCB
RF SHIELD PCB ASSEMBLY
QUARTER-TURN FASTENERS
Figure 1-4 Location of RF Shield PCB Assembly
SELF-TEST SWITCH
VOLUME CONTROL
Figure 1-5 Location of Self-Test Switch and Volume Control
Table 1-1 Operator Options
SWITCH SETTINGS ON 8-TOGGLE DIP SWITCH OPTION _ (Located at Position F10 on PCB) RESULT
| 1 [2 | 3 | 5 | 6 | 7 | 8 |
| Game Instruction | a | oN | | | Engle |
Language (as displayed OFF ON Spanish
| em TY setect) | OFF | OFF | German |
7 ‘ON [Free Play . OFF 1 Coin 2 Plays
| Coin Mede | ON | 1 Coin 1 Play |
| L | OFF | 2 Coins 1 Play |
T on | 3 Misses | OFF 4 Misses
| Game Length | ON | 5 Misses |
OFF 6 Misses
| ON | ON | Extended Play Hard* | |
| ON | OFF | Extended Play Easy* | |
| Extended Play | OFF | ON | No Extended Play |
| OFF | OFF | No Extended Play |
*See Table 1-2 for details on extended play levels and the double score bonus.
Table 1-2 Extended Play and Bonuses
PLAY DESCRIPTION
Extended Play Easy The player must achieve point score described below. The extended play points are displayed during the attract mode. When the 3000 points are reached, a short changing tone will alert the player. 3 Misses — 3000 pts. 5 Misses —4400 pts. 4 Misses — 3700 pts. 6 Misses — 5100 pts.
Extended Play Hard The player must achieve point score described below. The extended play points are displayed during the attract mode. When the 4000 points are reached, a short changing tone will alert the player. 3 Misses — 4000 pts. 5 Misses — 5400 pts. 4 Misses — 4700 pts. 6 Misses —6100 pts.
Double Score Bonus Double score bonus (2X SCORE) occurs when the word SKYDIVER is spelled out at the corner of the TV monitor screen nearest the player. If the JUMP button is pressed when an individual letter in the word SKYDIVER is flashing on the attraction panel, the same letter appears on the monitor and flashes. If the jump is successful, the letter stays lit. When all letters are lit, the player receives double score from that point onward and a musical fanfare plays.
Table 1-3 Self-Test Procedure
INSTRUCTIONS
RESULT IF TEST PASSES
RAM TEST
Remove Skydiver PCB from
the RF cage as illustrated in
Figure 1-4.
Set all DIP switches in the
small group (4 switches) to
off. Set volume level potentiometer {located on the audio amplifier PCB next to the Self-Test Switch) to Y% full volume. Set Self-Test slide switch (located inside and to the right on the single audio amplifier PCB) to the on
position. ROM TEST No operator action required. Wait for the last tone from Step 1 Screen should be clear. A series of eight high tones are heard. If all sounds are audibly identical in pitch, the RAM is good Graphics cover the upper portion of the TV screen. These graphics display the contents of the graphics ROM. RESULT IF TEST FAILS. A drop in pitch of one or more of the sounds indicates a bad RAM. The RAM location is determined from the following: Low Sound RAM Location in the Series on the PCB
Or NmMTHOR If RAM 6810 (at B1) is bad, the letters F1 will appear in place of the top “OK” just below the Graphics Display as iNlustrated below.
Below the graphics display, the word
OK appears twice as illustrated,
oral in TRS
The upper OK indicates that the 6810
chip (B1) is good.
The lower OK indicates that the ROM
check sums are al
Two stretched** black Skydiver men appear below and slightly to the left
of the OKs If the bad sum check occurs, a number will appear in place of the bottom “OK” that indicates the bad ROM location—as listed in the following table:
Fault Number PROM ROM Location* Location JO or J/KO Al E2 or K/LO —1 HO or BO & D/E2 or H2 D1 D/EO or DO D1 C/D2 or F2 cl E/FO or CO a
Ooranntno
- SWITCH AND’ LAMP TEST 3 Be sure that switch toggle 4 of DIP switch at F10 remains in the off state. Slowly press and hold down any LED push button or toggle any DIP switch to its opposite state; listen for a test tone each time a switch is pressed or toggl-
ed. Slowly release the LED push button or return the DIP switch settings, and listen for the same test
tone. All LEDs and the Skydiver attraction panel at the top of the cabinets should be lighted, as follows: 16 SKYDIVER lamps 2 Jump LEDs 2 Start LEDs
“No MSB or LSB determination **True when Self-Test is entered from the play mode. The image is not stretched when Self-Test is entered from a reset.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAME PLAY
The Skydiver game has three different modes of operation: ATTRACT — Power accepted or as a result of the end of a game READY-TO-PLAY — Coin accepted PLAY — 4 to 5 seconds after start button is pressed
A. ATTRACT MODE (See Figure 2-1)
The attract mode begins when power is applied to the game and the power switch is turned on (the power switch is located at the top rear of the cabinet as shown in Figure 1-2). This mode also occurs at the end of every game.
FS See
During the attract mode, the TV monitor screen displays the planes and little men jumping out to their targets. Note that Figure 2-1 has the black chute, but no little man, a blue man, but no chute. This occurs as a result of photograph and TV frame synchronization...it is not an actual visual display. The TV screen also displays the previous game scores, the standing high score, the point total required for extended play, the credits, and the cost per play. The player controls and sounds are inactive during this mode
B. READY-TO-PLAY MODE (See Figure 2-2)
When the correct amount of coins clear the coin acceptor, the ready-to-play mode is initiated. The TV monitor display does not change or vary from the attract mode display, although the PRESS START command does flash on the screen, along with the amount of accumulated credit.
The START LED pushbuttons light up and flash, alerting the player(s). Only the start buttons on the control panel will be activated during this mode.
Cc. PLAY MODE (See Figure 2-3)
The play mode is initiated from the ready-to-play mode previously discussed, by pressing either the black or blue player start button for a single player or two players. At this point the screen display freezes and the PRESS START command continues to flash, but at a more rapid rate. The pressed start button (either one or both) stops flashing and goes out; it remains so until the next game credit. Approximately four seconds after the start button(s) is pressed, the game goes into the play mode unless both are initially pressed.
When only one player presses either start button, the opponent start button continues to flash for about ten seconds. This gives the opponent player the opportunity to enter the game, even after the first player has already started. If no one presses the opponent start button within those ten seconds, the LED start button goes off and remains off until the next game. The computer will take control of the opponent position during this one-player game mode.
Assume a one-player game is in progress. The player must successfully land his skydiver onto the target of matching color. As the player improves his or her target landing skills for the highest score, the biplanes will drop down a level closer to the target, and while flying a faster speed.
The skydiver jumps whenever the player presses the jump LED pushbutton switch. The chute opens at the pull of the rip cord, and the skydiver glides down to the target. His flight is determined by the wind speed and direction, as indicated by the video wind socks. Each player has his own color wind sock to indicate wind speed and direction. The player, however, does have some control over these forces by shifting the rip cord control either to the left or right. This action guides the skydiver in the desired direction
The player scores by allowing the skydiver to freefall for as long as possible. This safe distance must be determined by a player while judging the wind speed, direction, speed and direction of his bi-plane, distance from the target, and state of the SKYDIVER attraction panel. (The latter is discussed in the following paragraphs.) The closer the target before pulling up the rip cord, the higher the target point score will be. The skydiver (or even his foot) must touch the target in order to score any points. When the skydiver hits the ground before the chute opens fully, he appears with his head in the ground and feet waving in mid-air. A video ambulance (see Figure 2-4) then appears on the screen, sounds its siren, and stops at the skydiver. Appearing to have loaded the skydiver, it then proceeds in the same direction off the screen.
Depending on the option switch settings, the player has 3, 4, 5, or 6 target misses allotted to him, and an extended play score to achieve. The most difficult part of the game is to attain the double bonus score. This double bonus is awarded when the player spells out the word SKYDIVER. In the play mode, each letter from SKYDIVER (located at the top of the Plexiglas shield) repeatedly lights up sequentially from left to right
Immediately below the corresponding player score is a video band (black or blue} that actually covers the word SKYDIVER. When the game starts, the letters do not show. Each time the jump button is pressed while a letter is lighted on the attraction panel, that particular letter is revealed from behind the band on the TV monitor and begins to flash. If the player hits the target and scores, the letter remains uncovered. If the player misses the letter, it is once again hidden behind the band
Figure 2-1 Attract Mode Figure 2-2. Ready-To-Play Mode
ed ae
J Figure 2-3 Play Mode Figure 2-4 Ambulance Display
Eventually the player has several letters of without missing the target: SKYDIVER displayed and occasionally will score a hit for the same letter he already has showing. This provides no advantage. The player must be more obser- When the player has completely spelled out vant to the letters displayed on the attraction panel SKYDIVER and the music plays, a 2X SCORE is He must synchronize with a desired (and stil! un- displayed below the player’s score. This informs the covered) letter and press the jump pushbutton player that all displayed target points are doubled
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Due to its solid-state electronic circuitry, this Atari unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this manual is intended to cover most servicing situations that may be encountered at a game site. The procedures given are in sufficient detail to be understood by a person with moderate technical background.
cc NOTE . if reading through this manual does not lead to solving a
the following two Atari Customer Service offices Atari/New Jersey Customer Service Office ADJUSTMENTS 46 Colonial Drive, Piscataway, N] 08854 Telex 37-9347 (Monday-Friday, 830-5 pm Fastern time)
Dial toll-free from anywhere in the shaded area on map below (800) 631-5374
Ca Cy,
From New Jersey and elsewhere in the U.S. dial (201) 981.0490,
Atari/California Customer Service Office 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4 pm Pacific time)
From Calitornia, Alaska and Hawaii dial (408) 745-2900,
From the remaining 47 states, dial toll-free (800) 538-1611
A, CLEANING The exteriors of game cabinets and Plexiglas® panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the acrylic plastic panels, because any dust can scratch the surface and result in fogging the plastic.
B. COIN MECHANISM Components On Coin Door Figure 3-1 shows the back side of the coin door assembly where the game's two coin mechanisms are mounted. included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. Powering the game causes the lock-out wires to retract far enough to allow genuine coins to reach the coin box. When AC power to the game has already been turned off, the lockout coil is de-energized, causing the lock-out wires to move out far enough to divert coins to the return chute.
Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire exten-
LOCK-OUT COIL LAMP HOLDER ding out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close
Also shown in the photograph is a slam switch assembly. It has been included to defeat any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed
Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 3-2. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pushing down on a release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 3-3.
Plexiglas® is a registered trademark of Rohm & Haas Company.
Figure 3-1 Coin Door Assembly Figure 3-2 Hinging Open the Magnet Gate Assembly
Figure 3-3 Removal of Coin Mechanism
Cleaning of Coin Paths
By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.
Figure 3-4 shows the surfaces to clean inside the coin mechanism. These inciude the inside surface of the
(CLEAN BOTH SURFACES WHERE COIN ENTERS THE MECHANISM, AS WELL AS THE MAGNET)
Figure 3-4 Surfaces to Clean Inside the Coin Mechanism mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.
If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a 3/8inch wrench and remove al! three nuts that secure the cover plate (refer to Figure 3-5). Removing the plate will provide access to the entire channel.
Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches
Figure 3-5 Removal of Plate Covering Rear of Coin Slot
Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication {and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism: Figure 3-6 shows this lubrication point
Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 3-7. Use extreme care when handiing or touching these wires.
MANUALLY HOLD DOWN REJECTION BUTTON AND APPLY ONE DROP HERE
LOCK- OUT WIRE
Figure 3-6 Close-Up View of Lubrication Point
In Figure 3-7 you will note that the coin switch trip wire is oriented into the “V” of the secondary coin chute. The wire should extend to only about 1/8” beyond the chute.
A retaining clip holds the wire onto the switch actuating stud. If you should loose a retaining clip, all is not lost. Just crimp the switch actuating stud over the trip wire with a pair of pliers.
Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean well-lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure 3-8 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by someone who has experienced in servicing coin mechanisms and who understands their operation. CORRECTLY ADJUSTED TRIP WIRE
Figure 3-7 Detail View of Coin Switch and Trip Wire
General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism
wervansonH ITEM IDENTIFICATIONS Kicker and Separator Screws. Washers Kicker Separator Gate Lever Spring Gate Pivot Pin Mainplate Assembly “¢" washer Rail Gate Assembly Cradle Assembly
a
: 13 Upper Gate Pivot Spring OG) 34 14 Undersize Lever Assembly 0 15 Magnet Gate Assembly Magnet Gate Adjuster Retaining Screws Coverplate Assembly Return Coverplate Coverplate Mounting Studs Lower Gate Pivot Spring Coin Release Lever Kicker and separator . Set the acceptor with the back of the unit facing you in the test position. . Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
- Insert several test coins (both old and new) and note that some are returned by striking the separator.
- Loosen the separator screw and move the separator a slight amount to the left, Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted. . Loosen the kicker screw and move the kicker as far to the left as it will go. the screw.
- Insert the test coins and note that some are returned.
- Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted.
- Be sure that both screws are tight after the adjustments have been made. wo
ightly retighten
Magnet gate . Set the acceptor with the front of the unit facing you in the test position. . Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.
- With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
- Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted.
- Fix the magnet gate adjusting screw in this position with a drop of glue. po
Additional Cleaning
- Remove the transfer cradle (12) and the undersize lever (14).
- Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
- Replace the transfer cradle and the undersize lever
- To be certain the coin mechanism is completely free of any residue, place the mechanism in boiling water for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.
Figure 3-8 Coin Mechanism, Exploded View
rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.
Correct operation of the slam switch can be verified by putting the game into the test mode and performing the switch test (described in Table 1). Correct operation of the other switches and of the lock-out coil can also be checked by the switch test, or else merely by manually operating them and watching game responses as it changes from the attract mode to play mode, and then back to attract mode again.
Cc. FUSE REPLACEMENT Skydiver contains seven fuses, five on the power supply assembly in the lower part of the cabinet and two on the TV monitor assembly. Power supply fuses are accessible through the lower rear door assembly. TV fuses. are accessible through the upper service panel door. Replace fuses only with the same type as follows:
TEC TM-600/623 Monitors: 3AG 2-amp and 0.5-amp quick-blow, 250 volts Motorola M5000/M7000 Monitors: 3AG 0.8-arnp quick-blow, 250 volts. Power Supply: Fuses F1 and F2—3AG 3-amp slow-blow, 250 volts Fuses F3 and F4—3AG 2.5-amp slow-blow, 125 volts Fuse F5—3AG 8-amp fast-biow, 125 volts D. TV MONITOR ADJUSTMENTS
The TV monitor should be adjusted only when the picture is distorted or if the contrast or brightness seem out of adjustment.
The monitor's adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure 3-9 shows the location of the adjustments on both TV monitors used by Atari. Your game contains a TV monitor manufactured to Atari specifications by either Motorola or TEC.
When making adjustments, follow these general guidelines:
cowraast | \\ Cvenr Cent un aright! HEIGHT / woniz. xoLo-t \_vert HoLo VOLTAGE SWITCH (leave in right position)
TEC MODEL TM- 600/623 2 Fuses nemove. Cover To REPLACE (both 8.8 A quick Blom) ‘conTaast — Moniz osc. BRIGHTNESS
MOTOROLA MODEL M5000/M7000
Figure 3-9 Locations of Adjustments on TV Chassis
BRITE (Brightness)— Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up.
CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being blurred.
HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal Oscillator)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture.
VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture.
E. TV MONITOR REMOVAL (See Figure 3-10) Remove three screws (button-head socket cap #10-32) at the top edge of the cabinet and remove the Plexiglas® retainer. Slide the shield out through the top of the cabinet and remove the smoked Plexiglas screen which is immediately behind. Next remove the cardboard bezel. At the back of the cabinet unlock the upper service panel and remove it. Now remove the six carriage bolts (10-24 x 2.00” long) that secure the monitor to the TV shelf assembly.Disconnect the TV monitor harness and slide the monitor out through the front of the cabinet.
F. ATTRACTION BOARD AND LAMP REMOVAL (See Figure 3-10)
The Skydiver cabinet has an attraction board with lamps mounted on the inside behind the Plexiglas shield, at the top of the cabinet assembly. To replace either the attraction board or individual lamps, refer G. LED START SWITCH REPLACEMENT The start switch on the front panel has a very low failure rate. To test a switch, unlock and open the coin door. Remove the wires from the suspected switch. With a multimeter set on the Rx1 ohmmeter scale, test the contact opening and closing. If the contacts do not operate sharply, replace the switch. To change a switch follow the procedures listed in Figure 3-11
@ Remove all wires from the suspected switch. @ = Turn the switch counterclockwise while holding the cone-shaped nut on the outside of the game cabinet. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires.
Figure 3-11 LED Start Switch Replacement
H. RIP CORD CONTROL RE- PLACEMENT (See Figure 3-12)
The black and blue rip cord controls, located on the main control panel assembly may need to be replaced if faulty or damaged. To replace this control, proceed with the instructions outlined in Figure 3-12.
TV MONITOR REMOVAL
Remove three screws that hold the Plexiglas shield in place.
Remove Plexiglas shield retainer.
Remove Plexiglas shield.
Remove cardboard bezel. V7 Pons
Unplug TV monitor chassis connector and remove six carriage bolts from the TV shelf assembly. e Remove TV monitor.
ATTRACTION PANEL REMOVAL AND LAMP REPLACEMENT
- Remove the attraction panel light baffle by removing two screws.
- Remove the attraction panel by removing six screws; unplug the PCB connector.
- Push, then twist to the right, the bayonet-type lamps to remove them. Twist the lamps to the left to replace.
Figure 3-10 TV Monitor and Attraction Panel Removal
24 = Skydiver
- Remove the two nyion washers from either side ef
| 2. | Unlock and open the coin door. | the stop pin, while being careful not to rub off the |
Molykote lubricant from the metal-to-rmylon sur-
| 3. | Unlock and remove the lower rear door. | face of the washer. Once again, use caution when |
placing them to one side, so as not to lose them.
- Reach through the rear door and remove the black , ABS plastic a hietl by removing the four pan-head 9. Push the stop pin through the shaft of the rip cord Phillips screws (4-40 x 3/8” Ig). control handle.
- Remove the Molex harness connectors from the 10. Font egonel straight through the top of suspected bad rip cord control. Panel. . 11. Reach through the coin door and remove the four
| 6. | Reach through the coin door and remove the two | black carriage bolts (4-20 x 1.00” Ig.) that fasten |
Unplug the AC power cord.
springs from the rip cord control stop pin.
Using a small bladed screwdriver, remove the two E-rings from either side of the stop pin, while being careful not to lose them. 12, down the rip cord control plate.
Replace the bad rip cord control with a good unli by performing the above rip cord control remoy in reverse order.
Le
Figure 3-12 Rip Cord Control Replacement
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
THEORY OF OPERATION
A. GENERAL INFORMATION
The block diagram in Figure 4-1 shows the major parts of the Skydiver game.
The game’s television monitor is a self-contained solid-state unit. The composite video sent to the monitor differs in many respects from the signal derived from commercial TV broadcasts. The picture appearing on the screen, therefore, is unlike that of a home TV set, and the monitor does not produce any sound. See Chapter 6 for a schematic diagram of the TV monitor.
The game’s composite video signal produces four video levels, instead of the continuous shades of grey seen on a home TV screen.
On the game PCB schematic diagram, Figure 4-2, the symbol “P” (appearing at various inputs of integrated circuit devices) indicates a connection of +5 volts DC through a pull-up resistor. For easy reference, the game PCB is divided into grid sections. Along the short side of the board these sections are identified by letters A through P (skipping letters G, |, O and Q because they may be easily confused with the numbers 6, 10, and 0 respectively). Along the long side of the board the numbers 1 through 13 are used.
Figure 43 is a harness schematic of the entire Skydiver game. This figure illustrates how all electrical and electronic assemblies are electrically connected together
‘ONIOFF DTERTOGK POWER SWITCH
SWITCH HORIZONTAL DEFLECTION EES INTERLOCK SWITCH
BLUE PLAYER RIP CORD.
SINGLE ‘AUDIO AMPLIFIER PCB
Figure 4-1 Skydiver Game Block Diagram
28° Skydiver
tana,
fg “9
| 3) | omazx | Lia], © | ole | < | sae | |
| 330 | &9 | a | 236 | 2 | 9316 | 24, |
| “ | P34 | ul | Sale | ce awn ewe | oF pmente | |
| 5h | 6 | 37 | ce | O12 Q3 NR | 8B al 02 Os AR | |
| an | c Fir | lays fe pe ie | pe fis fie fie fF | |||
| | | PR | Pee |
‘ womne
x reas aea8 esas sy
es veeser
| 2568 | ee | Taw | Pair |
G hro $ 2 tz
| oan | Pe | 32H | 7 | 2 | eco | VBLANes—Sf a7 | lp | 5 | ralt | VBLANER |
| 83 | 52 | 519) | Nee | 3° | 2» | ple | ||||
| 24 | —Skx™ | ale | ay | —Yee”® | ale | [die a] | iay | wa | tf | |
| fle | fel | FJ | WAV | ale Zo3!2 | 415 | '9 | ||||
| io | v3 | vey —2)a4 98 | ey ToL — veecet | |||||||
| ee | Re | Pee | ey | MS By oft | aldo 81 | |||||
| Hsyue | OYUN 3 | ere 1, | TELANE | |||||||
| mete | ay | Iai | OF | 1212) | 392 — ysyne | |||||
| w—Sas_ | 2 | PP | gap | |||||||
| ue | >>> | >>>> | owed | |||||||
| 2 | SN | El Ce | c | |||||||
| 22a | pay | . | 2508 | ass | = | om |
Lf” PR
| = | R12 20,2183 | wsyne | PRA |
tov ita vo . (PULL) Ho! ple +5v UNREG C1-21,26-38,40-S4, Bu85 28205 Sth. Levers)
| DIGITAL [AT | Ja | eka | SY | EL | sv |
| GND | TL | steer. |
Noise 4
+5V le
piseLayé ——4110 Mux
DISPLAY! a> Me DISPLAY2 ———"]4D Laren Disp Lays ——J30 ew eur cardi
WR S = 6a SYNC . POWER
NOTICE TO ALL PEASONS RECEIVING THIS ORAWING CONFIDENTIAL ‘Reproduction forbidden without Specitic wiltlen permission of ‘Atari, Inc,” Sunnyvale Calitornia This drawing is only conditionally issue beltner veceipt nor possession thereo! conters or transters Sry right in, or license to use, the subject matter of the drawing oF any dasign or technical information shown thereon, nor any right fa reproduce this drawing or any part thereat except for manutacture by vendars of Atarl. Inco” porated and for manufacture under the corporation's wit {en license, no right to reproduce this drawing Is granted ‘or the subject maiter thereot unless by writlen agreement ‘with or written permission trom the cornoration.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
MEMoRY MAP is (EEaIEHORSROOUAAGAAD EAGeano FONCTION is rs a cs 201 Txixblolofonxdklolclof [afololol|x|[o}o|p|ofo fo fp loll H ros Puawe 1 9011 [x}xlololololx[xfolaleh fol otal Iix[fo)o[oiolofp fol] H Pos PLANE 2 ove _Ix|xfofolololxlxfoloolviofol folfx[e|oip|p [> folofol| w# eos man 1 CICTEWMIEIES Ki ololol taste lp [p[el>|afol[ nh POS MAN e 614 IX fefolololo|x|x|ofojoli jon folo[p<] plo] ol plop [> fp || Ranae con Pert —tate alqalx|x{stolol fol toh Pleo Note COND Te Ixh<[olololoixix[slolel [a1 fo lIxifo]s aE Testy —hkixfolsfolon fopyoh eh Ix SE STOPS 2518 [x{xofasolxnloloton] folololh {ole pp opel v eos PLase 1 T3—ixhdtolstolotexfolojat Total taal B) Ter CRE PLAT OT folojol T fof follxlfptd}efe}ofstofol|- 7 PLANE, 218 Ix foloforslxix|ololoh olin Iblis ppp lojojoisfol erctuRe POAWe e 1c ix}xfolotololxixiaolol ti folo|tatlo! Ipipipip v Pos AS LS _xhelsfofolo, TETURE MATT Oore Ikkxbladololxxolfolon 1] f folx[p[oipfoipopplv eos man & Sorry xIx[olo) DSTIES [SIS PIE TURE an Dogo -o07FlIx|xJolo[Olo|olol JAIAIAL ATA [PIS foto) RSE WER Saw (HIER joaoo-o17F xix [olololi Talaafalala (alalalAllx([ (5 [p[elS|opfof[ Pc ay re cD OFFI] x folojol | TH TATAIAI AlPdsfo[ppelollslp | mars ro o505~ 00 Bexx I}xfoott LATCH I 1 B05 (xxbioh fxlaletxtxpaxlotal ENEEI IESE LAW oece Mixlaoh [xixtxbdx px (olol: FIESES EVES AM Sess etxtarat hdxheabsbebetal lobe ttnlhe bebe fey befebell <r — ET esos Mxlxfololi Pex[xfix Te xfon fT fOllwik lad xix[xpaT stage Cre 2 280. Dlx] DESIG Ca EN FAES ESE! Es CIES Es aad a fos om Ti xlotoh epee ixpctxpet tol iebdxbbe lS LAME Boe H expt ESESE0S 637363 | REIISISMEAST.N Tex taATcN 2 Soo [ksh faxixhe atx x oo Rix eT some TET Tose x[Klob foley hex xp afolor Meebo com cose OUT oe elxfop tote xt 3 EN BC IFSESESE ed Sc RAE 2o8 lope fate xp Pelt Pade px Se TOOA ont folstatxPax|x] xT Lol xPaxfxixtxpal wis tes 2 Looe ORME EEE! BIS NER FES Fs ASST TOOe FU GIES ESE EAAE i EEIEE SSESES ESR) xx TNbuT Ace AGT EO CISMIREICR zl aso Sex eax T BEC EIEEASAES) INE ESEAFS ESEce eA TEST Txfxoh [oepdetxd To o Ibn xtxtx[ xx eet 2 I BREE ICCIC El ca BIxIxI Rica, BSE Teoh Bitola! (JEEPS 6a FH OSI FARA KWINFALSES lololorite x xpaix] SHOT 1 Pecos ota toletetoloiot ts EiEaFSEAEs OTN TURMESIAAGA Tre lio hed KIA Chote 2 Bos _[xpaohyt Ears} Tp) of= Sw Ret TEST Onn I on kx Ce) oP 5 1805 _|lalxfohT Txlxlabre aol RPE BEC OFT Sw _ Mol Tx [xpaxPed 4 tol Tor Px pe| Ca) on T Sw 5 Ol OaTIGS. Boe Io tix ixt bloat To CT nn Piolo fo. Eoin 1Ba7 FAS INN EAE 5 Cel xict £4 = lou Tr oI H rarer CHS TSss8 thdxeht exp ol x fole rel ph< Lat Misses aol Ube xxIx Teoh Pfololie: XI] MoRSESE Taos _tktxlorh tale eter xlolr xSe Rebgoh TTX epexixlo Teo [el Cone TS0R fo he ahaa alo hes AXP Ee xtEN DES PLAY ‘an alot x UTI AD TSo8 TxxoM Px] Xlop Te x LANGUA aa SI eb ]Or Pet TARGUR: Tears eee bebe OTs [oto VeCANE Mbh I bicep it lope reese TS frebeloliT Pelee x pelofx fol DOSES peo Pax fx dfx! coh fol a = [Bo6. Tot pa Mee eesit Boz Talxhifel Ieit TLA‘A r n TEAM 3 Toto [okt EAMe oo olshkT xx xxix [oft [otal bl CAME A TSYT lolol [a] Ser 20 iS) ni Es H or [2500 2FFeIXIX] Tol [LALA me Serial ESE MDESPNES ATALA mt seer ipoh [ti EMENISENICA . OM 05-1 Toh a] iy
Figure 4-2. Skydiver Schematic Diagram, Sheet 1 of 6
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction erbidden wilrout the ‘Specific written. pession of ‘Atari. Inc, Surayvale, Gaivfornia’ This drawing is only condiionally issued. and ‘either receipt no’ possession thereo! confers or ansters any right in, or icense to use, the subject matter of the ‘Srawing oF any design or technical information snown thereon nor any right to reproguce ins drawing or any bar ‘ep lormanutactore by vendors of At nd for manufacture under the corporaian's wi +59 ight io reproduce ims drawing is granted DOr te Subject mater nereo! Unless by wntlon agreement If wth oF witten permiseran trom the corporation 's DISPLAIS—“SIAY yg DisPLang——"Sa@ DySPLNS— 7A? . DISPLAY: Ae 2150,, og—4 visetari——$ as Yan og DISPLAN EB ost . av —Ss ie o2f2— ev 12:99 1 w—Sa wa Sas
epfo =
eoune
ols u
| TEER | Ong | pisPLay7 | 8) | a3} | — | orsPuav7 |
| 4 Ey | 2564 | Sire | 250K | |||
| sence | al | 28 | af | goon | —2fS8 | |
| at | PI 931 a | COMP SYNCH | ase | aSGk | ||
| YSYNG | BIN ENTR | Hot |
A VEL ANIC oO. 3,
| 2) | ee __ a6) | es | ||
| 4 | Pe ME TC | 3 | Sou | a |
| Teoe | : | aH | oy | 4a |
s HBLANK L ‘sane RCORD LATE
ance 44 @t]e 4 COMP BLANK fro] shame
we d- “e
| Fit | ‘f= | aifS—— | com Locnout |
zesetT —-3T el 3 D asi Wie BAS AL al
| 2 | 3 | pay | az, | |
| BAR | Fi | ba F | WHISTLE | 2N3C43, |
| BA | S/S? | 85 | wHstLee | = |
| BAS | 30 | NMION |
wipte
fae zens le T]y Lamp
DLAMP,
. Bu o —— auf 28 une CORRE st? MICRO PROCES SOR
Tey aneoae le al 7 [P] com Lockout Cow Lockout
Figure 4-2 er Schematic Diagram, Sheet 2 of 6
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction. forbigaen without the Specific written permission of Atari. Inc... Sunnyval Catfornia. This drawing 1s only conditionally wssueg, and either receipt nor possession thereo! conte's or transters {ny right in, or license to use, the Subject mater of the Grawing or any design or technical informavon shown tnereon, Sor any right fo reproduce this drawing er any part thereot, except for manutaciuie by vendors of Al porated and for manufacture under the corporat ten license, no right to reproduce thts drawing is granted Oring subject matter thereof unless by written agreement with or written permission from ine corporation. -ol EM ADDRESS DECODE | ~02
| Alan. | 20} | tev | 48 | +5v | sv |
‘3 so sa}2pisPLavd {
| naff | 42 HO | Digpi aya. | lea lea | lea jer | 24 fat | 24 Jat |
| 310°" | 1a} — pisprava | ey SS] | or SSS] | cy C88] | gy SSF | |
| ap | _3aP? | DISPLAYS | OSB64 | ]OBlES [O33O& | 033107 | ||
| Kz | 19| | Rom | ROM | Rom | Rom | |
| “a | ao | 3 | ||||
| b2 | BAD | ad | ||||
| PRBS | nee | ae | ||||
| BAT | - | AT | ||||
| BAG | 4 | Aw | ||||
| 4| | BAS | AS. | ||||
| 4 | gaa | Ag | ||||
| Wap | DISPLAY! | BAS | 5 | AS | ||
| 1315p | SQ) We | DISPLAYS: | BAL | = | AZ | |
| ols | FF | sal7 | o | |||
| 3D | 3a) | DISPLAYS | BAI | lout | ||
| i | io | af | DISPLAY? | —— | Aw |
cx 7
| fi | pes? | —T | + | > |
| —— | re | DBUSE | he | |
| — | PRES | Deuss | 3 | os |
id
| ——H | aus | os | 10 | |
| a | ere | 13 | bs, | ROM? ——9 gs |
| iE | eral | »—? | —__| 4] 3 | |
| 4l_p | Is. | pBUSz | joe |
peusd 10)
| it | T | Deus! | 9 | Pt | 3, | |||
| ol | 7 | pause | Deus | be | ne | BD) | ||
| y | i | = | ela | ole | ale | = | oe | vf? |
| GB | Rls | Gils | Ble | ae] | ee | AE | ||
| 2 f | Is | pauss | 2 rr | zope fie | eye | fie ie | id | . |
7 Hi
| t | rol | 3 | pause | ROMI | = | = | = |
ROweA SS
| h | — | F | |||||
| +sv(+SV | tev | otsy | sy | tsy | o¢sVo+SV | ||
| Ne | be | Je | fe | fe | fe | fe | fe |
| pare L | af | die | cpa | SKO | K/L | He | Fo |
<4 OOO.) 3800 L | 7800 L | 2BOoM | Zo00M]2B00M)| 7B800M) [C8388 [033169 | 033176 | 233171 | 233172 | 033173] 033174 | O83I75| BAe a
| eas | —S | as |
‘el ena AB BAT AT BAe Ae as as eae ——4a4 Bas a3, RAZ AR
| +2! | ts | Deus? | BAL | in) |
| Lv | J | BAS | ae | |
| TT ay | DeUSE | oF | z | DBUST |
| Raa! | peusz | 03| | eT | DUS |
| peusi | oe | ST | BBS | |
| pEuse | ° | : | Deus | |
| me | z= | ce | ||
| ep | yep | [ep | joys | |
| \ | + | = | Ss | = |
x3 ROMS a War PB ad Row F Ket Rol
| f | BcK PFD | AEA |
Az{O0, ROMZR
Figure 4-2 Skydiver Schematic Diagram, Sheet 3 of 6
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL’ Reproduction farbiaden without the Specific writen permission of Atar. Inc... Sunnyvale, Califorma. This drawing ts only conditionally issued, and neither receigs nor possession thereof conters or translers any night in, or license to use, the subject matter of the
| ssee | e2es | drawing oF any design or technical information shown | |||
| Le7e | ae | ey | thereon, nor any “ight {0 reproduce this Grawing or any par | ||
| 3445 | aoa | Rego xcept or nature by vandoree an near | |||
| 5 | alz | zag | a | Borated and for manuacture under the corporation's wht | |
| Sioe | gl? | viog | SSS old | 55S | fareteenge, no ght te reproduce the Grawing granted |
| Ba55 | 4 | ‘or the Subject matter Ineo! Uniess by writen agreement | |||
| PA We | paso | Pree | wtih or writen permission irom the corporation | ||
| Wp 9322 | ¢ | | | |||
| vipt | 3 la js fo lo | a i Is Je | |
“Ree Oe Rey, f REE SS
| ' | Reae—lee | eter | |||||
| 3) | Wib2 | id | Ps | WS | 7 | Pa | is |
| 2sen—> | er | « | lee | eo | —___ | ||
| . | 10! | Lsiea | zh. | estes, | PUADEt | JPCANE: | |
| ” | 2 | emaz«—be—2lce sin cha _ | loc Bin eNTR | VPCANE: | |||
| sic | 1B | oa @gac ap = | Oaae oe obo | ||||
| ct | Ta fs he fr | bys p2t" To | eas | s | |||
| TTS | . | I~ 2| | |||||
| Rees | 4 | — | |||||
| . | 5 | it | => | aT | |||
| SB | y | sor | 12, | u |
ret ZrEy
| 25% | 58S | Som | BD |
ae ze 453 2559 B54 PAae
2 |4 |s 3 1¢ [5 le | rea, o[ A&C ee De pep ao
| sie | Hl | - | |
| t—4]cc gn Ge | Zhe ge ete. | ca 9 | ee |
| 2A ad OL QD E | A 2B oc od | a {sz | VPLANES |
| Ta ns 12 10 fh | 13/2) | eas | = |
| >Re: | — | aR | |
| } | Res | alse >> | SATE |
~ ft ” ors \
| DISPLAYS | eyes | ae zy | SEY |
| 4454 | $458 | wot |
eaeaale zara Gswsla waa ap 6 a5 4o58 4 10
| a le [so fp | Bla lele | BP), 2 | Taran | |||
| is | Ref | A Be DT [RBA A | ||||
| . | a2 | pater | p—Ser | |||
| ' | i | ‘lM | ls | 7 | Ma | = |
| aA | 7 | + | y | ool | EP | |
| eH | 12 | wa | ere | a | sek | snFTs |
| 4 | z | TOR2 | fee ai te | ce ain eure, | ||
| \ | pies | (8A 98 ae GD. | oa ce atop é | | |||
| ren | ®is 3f > | tORS | Taya jie | ji | fete beney | |
| 1 | 2308 a | LBS | b | ||||
| 3H | jc | s | RANGE LD | 4 | Beas | RE |
2|¢— Nore co
| {oF} — NAW | Bose | g¥ge | |
| ar | 535 dye | ois | |
| ar | 5355) | SSS | |
| [DECODER | 66 a dls | aaao | |
| ' | ame | —2egay | gone |
| 3 |o |s |e jo | > |e ls |e |p | 13 | MP 4 — Tan |
eas, [A Be DL] LAB COT
| 8 | eter | eset | us | | | ||||||
| a2 | Sha | 7 | = | 13 | cofS | Her | 4 | eo'S | 915.8 | SHiFTa |
| 2h, | csles | zr | ties | 4 | ||||||
| z | tc Bin te | ce giventR | cs | |||||||
| . | " | s\, | 3 | BA QB eC gd S | GA 8B GC OD | |||||
| ms | xe > | Ta Ts le fer | Ta [8 fiatn fr |
9301 4 : P
| 326 | e. | 8 | ary | Pees |
a z pF MOTION
[DecoDes E
Figure 4-2. Skydiver Schematic Diagram, Sheet 4 of 6
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction’ forbidden without fic writer permission of Atari, Inc, Sunny iar This drawing is only conditionally issue receipt nor possession thereof confers or transfers Tight in, of license to Use, the subject matter of the Grawing oF any design oF technical information shown {herean, nor any right fo reproduce this drawing or any part thereo! except for manulacture by vendors of Atar, incor porated and for manutacture under tne corporation's wit fen license, no right to reproduce this drawing is granted forthe subject malter inereo! unless by written agreement (with or willten permission from the corporation.
z Roo OR SYR $ VRCAREe. N38 Wak 8 amas 1) 385
Slee ual 7] vives la GND
| 5 | one | +SV 00 -45V00 | SV | HSV | Sv | tsy | HSV | HS |
| eo ae | his | ja | le | he | he | fia | he | ia |
| ed nals | F/R | iid | Dies | Ere | Bicw | Be | be | op | # WOT USED | |
| Isn/eeqoet > | acoor | |3q00 4 | acoot | 7e00L | 22d0m) 340M] sc00M| TeSOM | ||||||
| elt | amps | —2|_* | [028175 | fossiogjosaiei|” | + | | 033163 [Ossie | ||
| a | aah | BAS | is | |||||
| ols | Nowe | sas | —4 |
a7 4
| No | Bae | 2 | | |
| a | B | Bas | sl |
| oe | BAG | Pi |
BAS 5 a2 z
| Ha | BAL | : |
| Baia | —2[>e2— ta | ba |
3 u ht Deus: 04
| oa | 3 | 2 | ia | BUST |
| pause | 88 | Deus | ||
| BUSI | 8 | 3 | ||
| s | a | | | ha | DEUS |
| ves | oO | deusa |
se =z re
| ioe | pop | jos |
oma
| Romi | + | I |
ROMA Romze 4 ~ol -
Ree . RAR. Auris AUDIO. VIDEO MEMORY
Figure 4-2 Skydiver Schema Diagram, Sheet 5 of 6
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
BAS 3 Az
BA! F
LATCHS- ae & Ho ' Ree Se SL “I LATCH a> oth acre No\seé RST
NOTICE TO ALL PERSONS AECEIVING THIS DRAWING CONFIDENTIAL” Reproduction. forbigden without ine Specitic writen permission of Atari, Inc., Sunnyvale, California” This drawing 1s only conaitfonally sued, and neither receipt nor possession thereof conters or transfers any right in, or license To use, the subject matter of the Srawing oF any design or technical information shown thereon, nor any right to reproduce this drawing or ay part thereo!, except for manufacture by vendors of Atari, near porated and for manutacture under the corporation's wnt {en license, no right 10 reproduce this drawing is granted forthe subject matter thereol unless by written agreement ‘With or wetten permission from the corporation R22 Wy Mik © 3 |4 ELI REE OL eP cio tole, AB is |e 4sv ey eo Sic! aheg > 4 Pn A QB ACAD C Te Tape ye Bl
PRO har we 8 JAB Ou ag
as. ae PBT Ha aw D4{—de eajw —2>>-* sai cap PS}
- —le3 Pee ‘S| ee ne D3 4 vz}4— va tee a ap—o ze > — 00 “D" LAMP
“WT LAMP
“Ee” LAMP
“R” LAMP
Figure 4-2 Skydiver Schematic Diagram, Sheet 6 of 6
44 POSITION EDGE 7] CONNECTOR,
| TISV_GED | 1 | es | rt | +R |
Fie GED Bs ; “HOv UNeEG [Zt is | Rov oNeEG a
=
| EQe ne | a | im |
BACK Jen oP fo “BV [= }&
| AUD | ip | pe | |
| AUlID | SED | epee | + |
| Pecan | 7 | tS | |
| a | + | Ne |
Lave Ea
| ae | orm | oz | = |
| START SLACK LAL | } | Se | |
| START BLUE LPI | K | a | |
| SAME | 1G} | se | |
| LAME | Lj} | ee | | |
[BLACK SiGur api; pew +P Bue _@GuTnol mp [Sood cuore nope Se BLACK Ceure nol NBS (COIN UIRIGHT)NOI 1S BNR TocKOuT pL Ses: = Bue Lerrnuofia = rT >
| Con 2hermNe.| | © | |} |
BLACK JUMPNO. 3s BLACK LEFT NO) S Bu/ee BiKCK STARTNO} Io
| Bove JuMP wo.) | 7 | PORN |
u =a epee “BUDE _StART NS] Vv ES
| — | cAMP | hsp | ee _____ |
LAME wv ~
| VAMP | x | een |
ViBES al TvibEG “pn
- 2c}-E= “GRD z
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction ‘orbicden” without the Specitic written permission ot Alar, Inc.” Sunnyvale, California. This drawing is only conditionaly issued, and either receipt nor posseasion thereo! conte’s or ansiers any right in, oF license to use, the subject matter of the Grawing or ‘any design or technical information shown thereon, nor any rigntto reproduce this drawing ar any part Iherect except for manulacture by vendors of Atari, Moor porated and for manulaciure under ine corporation's wrt envlicense, no right to reproguce this drawing is granted fF the subject malter thereot Unless by written agreement \with or welten permission trom the corporation.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
TRANSFORMER We-TIST Y | 220V JOR ! .
HOV VOLTAGE OR SELECTION [- BLOCK. SHOWN
SV OUT
usv OuT
AC INPUT
NOTICE TO ALL PERSONS RECEWVING THIS DRAWING CONFIGENTIAL” Repieduction ioaiagn wilt the specific written permission of Alan, inc. Sunnyvale, California This drawing only onde Issued, and neither receipt nor possessior fs ortvansters
ar, heer nd for manulacture ude the corporation's wit f Tight to reproduce this drawing is granted ore subléct matter theres! untess by water agisenens with or written permission from the corporation
PCB ACOL555-01 cr -™~ R! Nia £ ty ¥ | 22,0004 | | S| @lBv ! o | + Rl e | a fs__=] v 2 OR Ao FUSE
PE FUSE POWER TO PCB
Te TP
iNTERLOCK
Figure 4-4 Skydiver Type B Power Supply Schematic Diagram
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ILLUSTRATED PARTS CATALOG
The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Skydiver game.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this catalog, and the serial number of your Skydiver game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbigden without the specitic written permission of Atarl, Inc.” Sunnyvale, alforna Ths arawing fs only conditional ssued, and its F possession thereat confers ef iransters sense tO use, (ne subject matter of tne ‘Grawigg oF any design or technical inisrmation shown thereat, nor an ht fOrebroduce nis drawing or any pat yxcepl Tat manufacture by vendors of Atari Iecor porated anc for manufacture under tne corporation's ws Yon license, no righ to reproduce this drawing is granted ‘or ihe Subject matter thereof unless by written agreement “with oF written permission from the corporation
Oils
v= Pa
el
Vv.
NOTICE TO ALL PERSONS RECEWING THIS ORAWING CONFIDENTIAL” Reprodvetion, forbidden without the pormiasion of Atarl, Inc. S
or any design or technical i ° {hereot,norany rho ceproduceinis drawing or any part ndors of Atari, incor nto reproduce this drawing 's granted forthe subject matter thereot unless by written agreement with oF written permission trom the corporation.
Figure 5-1 Final Assembly A033037-01 B
Figure 5-1 Final Assembly Parts List ATARI Item | Part Number | Qty. | Description Item | Part Number _| Qty+ Description 1 n033043-01 1 | caninet Assembly with Graphics 40 75-9318 2 | wing nuts, #10-24 2 (A007197-03 1 Power Supply Assembly Type B 4 82-1624 10 Wood Screws, #8 x 1h" Ug. Ft. Hd. Phil. 3 2033042-01 1 | Control Panel Assembly 42 72-6610 26 | Screws, S.M. Pan Hd, Phil. #6 x 5/8 19. 4 030836-01 1 | lower Rear Door Assembly 43 | 72-6608 7 | Serews, Sim. Pan Ha. Phil. #6 x 4 Lg. 5 n033048-01 1 | Assembly, Light Panel 44 72-6808 1 | Screws, sim. Pan Ha, PhiL. #8 x 4 1g. 6 | x030836-01 1 | t.v. shele Assemply 43 72-6812 16 | Screws, SM. Pan Ha. Phil. #8 x 3/4 Ig. 7 (033045-01 1 | vacuum Formed Overlay W/Graphics 46 | 78-2500 1 | Screw boun Tie Wraps 8 n009574-01 1 | Assy Audio Boara a7 70-11-1816 5 | Lamp, incandescent, Minature, Bayonet: Base 12 9 2009083-01 1 | coin Door Assembly 43 | n033081-02 1 | Harness and Switch Assy. io} 030867-01 1 | assy, R.P. shield Enclosure 43 72-6810 6 | Screw, oM Pan Hd Phil. #8 x 5/8" 1g. ar | aosso16-01 1 | Power Cord Assy, Strain Relief 50 | 72-1406s 4 | Screws, Mach. Pan. HD. Phil. #4-40x 3/8" Lg. x2 | n033046-01 1 | R.F. Shield PC BD Assembly 51 75-07021, 3 | #20 Nylon Black Washers 13 | 4009787-01 a | P.C. Board assy, SXYDIVER (Prom Version) 52 03304901 1 | Shield, Aas Liquid 14} 006305-01 1 | Printed Poly Bag as} tH-u17 1 | Operation, Maintenance and Service Manual, Complete
with Illustrated Parts Catalog 16 006873-01 1 | Retainer, Plexglas 7 032049-01 1 | Piexigias, shield w/craphics 18 909010-02 a | Beze1, Cardboard 19 000869-01 a | speaker, Grill cover 20 (005233-01 2 | Rear Door Seal 21 006319-03 1 Copyright Decal 22 75-5132N 2 | Carriage Bolts, #10-24 x 2.00" tg 23/ —a007902-01 1 | cash Box Assembly za] st-117 a | sere test cnart 25 (006870-01 1 | coin Box Bracket 26] —9030453-01 1 | Assy. Rear Door, Upper Service Panel 27 75-040 a | washers, split Lock, #10 28 42-001 2 | Speakers, @ inch 29 73-7015 6 | Rivets, 3/16" 0.D. x .68 Lg (.250 x .500 Grip? Black 30 46-201302 2 | Fuses, 3 AMP 31 005594-01 2 | Corner, Mounting arkt. 32 033095-01 2 | Label, Shipping * a lsubstitute for ited 13 ig A009787-02 yty of 1, PCB Assy, SKYDIVER (Rom Version) 33 82-8016 5 | Screws, Button Head, Socket Cap. #10-32 x 1.00 La 34 75-99090006 | S$ | Wellnuts, Blind Hole Fastener #10-32 8 75-0108 a | Washers, Fiat, #10 36 75-5516B 4 | Carriage Bolts, #4-20 x 1.00 tg (Black) 37 75-9115 2| Hex Nuts, #10-24 18 75-0158 4 | Washers, Flat #& 39 75-990505S 4 | Hex Nuts, #2-20, Nylon Locking © ere corencaions Coreary
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
LS
AULA LIIULDLDIUI TD NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 1 idden withoet the
any Srawing er any design or techr thereon, nev any rightto 1
orthe subject matter thereat ‘mitt oF witten permission from the corporation.
T vl {|
i t a pee eee T
lh \
! i {
I
{ J r
Figure 5-2 Cabinet Assembly A033038-01
ATARI Figure 5-2 Cabinet Assembly Parts List
—=
| Item | Part Number | Qty. | Description |
| 1 | A033033-01 | 1 | Assy, Side Panel Cleat, Left Side |
| 2 | A033036-01 | 1 | Assy, Side Panel Cleat, Right Side |
| 3 | 006846-01 | 1 | Base Panel |
| 4 | 033035-01 | 1 | Panel, Front | |
| 5 | A033039-01 | 1 | Assy, Coin Box Shelf |
| 6 | 006849-01 | 1 | Cross Panel, Front |
| 7 | 030831-01 | 1 | Panel, Middle Front |
| 8 | 033034-01 | 1 | Support, Monitor |
| 9 | 006854-01 | 1 | Top Panel |
| 10 | 006853-01 | 1 | Upper Rear Panel |
| ll | 006852-01 | 1 REF | upper Service Panel | |
| 12 | 030834-01 | 1. REF | Shelf, Sliding, T.V. | |
| 13 | 030833-01 | 1 | Panel, Rear Cross |
| 14 | 030832 | 1 | Panel, Center Back |
| 15 | A006877-61 | 1 REF | Lower Rear Door Assy | |
| 16 | 006847-01 | 1 | Lower Rear Panel |
| 17 | 030830-01 | 1 | Shelf, T.V. Support |
| 18 | 033041~01 | REF | Light Baffle |
BED CYaYX3XO
pera. Zh LUE, PLAYER A
¥/e Figure 5-3 Control Panel Assembly AG33042-01 A NOTICE TO ALL PERSONS RECEIVING THIS DRAWING Ghiornia’ This drawing «6 only conditionally iss hether receipt nor possess'on mere! canter oy transfers Gay ght mn. oF license to Use, the subject matter of the ‘mlormation. shown porated and for manulacture unde: Ine corporation's wit {enicense, no Nght to reproduce this drawing vs granted SF the subject matter thereol unless by written agreement laity or written permission from the cowporation.
ATARI Figure 5-3 Control Panel Assembly Parts List
[item Part Number Qty. Description
| 1 | 033040-01 | 1 | Control Panel W/Graphics |
| 2 | A033084-01 | 2 | Assy, Ripcord Control |
| 3 | A033082-01 | 1 | Control Harness |
| 4 | 62-002 | 4 | Led Switch |
| 5 | 001856-01 | 4 | Bushing, Switch |
| 6 | 75-5516 | 8 | Bolt, Carriage 4-20 x 5/8" Lg |
| 7 | 75-0158 | 8 | Washer, Flat i" |
| 8 | 75-045 | 8 | Washer, Split %" |
| 9 | 75~-915C | 8 | Nut, Hex 4-20 |
| 10 | 75-5120 | 2 | Bolt, Carriage 10-24 x 1.25" Lg |
| ai | 75-040 | 2 | Washer Split #10 |
| 12 | 75-911S | 2 | Nut, Hex 10-24 |
t vere communratons Comeary
to- 20% se0cton se STOIRATA AVIA YA2 da MAJ HOITOARTTA
@® Ww Praces a ASSEMBLY SCALE: 271 TRACES SHOWN ARE. ON aRCUIT BDE lo te te 1. 3) e
©
Fs
me
Figure 54 Attraction Lamp Board Schematic and Assembly A A033092-01
Figure 5-4 Attraction Lamp Board Schematic and Assembly Parts List
ATARI
[item Part Number Qty. Description —
| 1 | 033093-01 | 1 | P.C. Board |
| 2 | 79-4313 | 16 | Socket, Lamp |
| 3 | 79-58005 | 1 | Connection, 10-Pin |
D> Weve: conmsncins Comey
- 6 eeaD
Figure 5-5 Attraction Lamp Board with Lamps Assembly A A033047-01
Figure 5-5 Attraction Lamp Board With Lamps Assembly Parts List
ATARI
| Item | Part Number | Qty. | Description |
| 1 | A033092-01 | 1 | Assy, Attraction Lamp Board |
| 2 | 70-11-1816 | 16 | Lamp, Incandescent, Minature, Bayonet Base 12V |
] + vare: Communearons Company
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction. forbidden without the
ten license. no right to reprodtce this drawing 1s grant Dr the subject matter thereot Unless by writer agreement with oF written permission trom the corporation:
NCTES: A\ STAPLE AS REQUIRED ZX are ttm 8 We pS IT. SHELF IS SHOWN, ON CNE SIDE. AX APPLY ELL SILIONE: RUBBER (GE 198 OR EQUIV.) WHERE SROWN
Aerow \\
Figure 5-6 TV Shelf Assembly A030836-01 Cc
Figure 5-6 TV Shelf Assembly Parts List
ATARI
| Item | Part Number | Qty. | Description |
| A | 030834-01 | 1 | T.V. Mounting Board |
| 2 | 92-032 | 1 | T.V. Monitor, 23" |
| 3 | 006874-01 | 1 | Plexiglas Retainer |
| 4 | 75-5120B | 5 | Carriage Bolts, #10-24 X 1% Lg. |
| 5 | 75-040 | 5 | Washers, Split-Lock, #10 |
| 6 | 75-010S | 5 | Washers, Flat, #10 |
| 7 | 75-911S | 5 | Hex Nuts, #10-24 |
| 8 | 78-6601216 | 1 | Alum. Foil, 1" Wide X 10" Lg. (Approx.) |
| 9 | 75-0158 | 2 | Flat Washer, #% |
| lo | 033050-01 | bl | Strip, Cardboard |
- 6 PLCS
G6) - 8 a © 2 PLCS Q)) -
- 2 PLCS (S) 2 PLCS @1) 2 PLCS 2 PLCS @3)
. ®
@ 3% ee hii | @i)2 PLCS
(5) 4 PLCS Qa)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbidaen. without the specific written permission ot Alar. Inc, Sunnyvale, California. This diawing is only conditionally issued, and Neither receipt nor possessio confers or tansters ‘subject matter of the formation shown nor any right {0 reproduce this drawing or any part thereo!. except for manufacture by vendors of Alar, Incr porated and for manufacture under ine corporation's writ {en license, no right 10 reproduce this drawing is granted forthe subject matter inereof unless by writtes agreement with oF written permission from the corporation,
Figure 5-7 Coin Door Assembly A009083-01 Cc
Figure 5-7 Coin Door Assembly Parts List
Description
1 A007637-01 Front Bezel Assy. - Used only on -01 Coin Door Assy. A007637-02 Front Bezel Assy. - Used only on -02 Coin Door Assy. A007637-03 Front Bezel - Used only on -03 Coin Door Assy. A007637-04 Front Bezel - Used only on -04 Coin Door Assy. A007637-05 A007637-06 A007637-J7 Front Bezel Assy. - Used only on -05 Coin Door Assy. Front Bezel Assy. - Used only on -06 Coin Door Assy. Front Bezel Assy. - Used only on -07 Coin Door Assy.
See Fiqure 5-14
| 75-9165 | 4 | Nut 6-32 | |
| A030362-0L | 1 | Coin Lock-Out Assembly See Figure 5-15 | |
| A007640-01 | 2 | Coin Switch Assembly | See Figure 5-16 |
| A002465-01 | 1 | Coin Counter Assembly | |
| 004320-01 | 1 | Coin Door Weldment | |
| 064341-01 | 2 | Secondary Coin Chute | |
| 004344-01 | i | Key Loop | |
| 004340-01 | 2 | Spring-Return | |
| 004337-01 | 2 | Bracket, Wire Form | |
| 004338-61 | 1 | Lock>Out, Wire Form, R.H. | |
| 004336-01 | 1 | Lock-Out, Wire Form, L.R. | |
| 004326-01 | 2 | Button, Scavenger | |
| 75-046 | 4 | Lock Washer, #6 | |
| 006904-01 | 2 | Spacer | |
| 007359-01 | 1 | Lamp Secket | |
| 70-11-47 | 1 | Lamp | |
| 73-3008 | 2 | Retaining "C" Ring, Pruarc #5103-25 | |
| 75-9914001 | 6 | Self-Threading Nut, Tinnerman #SR18400G | |
| 75-026S | 4 | Washer #6 | |
| 75-00516 | 13 | Kepnut, Style 842, Stl., 6-32 | |
| 008629-01 | 2 | Spring | |
| 71-2118 | 1 | Leck Assembly, Hudson Lock | |
| 71-1225CU | 2 | Coin Mechanism for American Quarter only |
71-125FB Ref.| Coin Mechanism for Belgian 5 Francs Only 71-1205FF Ref.] Coin Mechanism for German Mark only 71-1201 MG Ref.| Coin Mechanism for Swedish Krona Only 71-1201KS Ref.} Coin Mechanism for Japanese 100 Yen Only 71-1210PE Ref.} Coin Mechanism for English 10 Pence Only 71-1220CA Ref.| Coin Mechanism for Australian 20-Cent Piece only 007753-91 Plate, Anti-Probe A007638-01 Switch Assembly - Slam A006921-01 Harness Assembly
© A Warrer Communications Company
roses WILL BE USTED ON THE FINAL,
ASSEMBLY PARTS LIST OF EACH INDIVIDUAL Game,
- SEE 907197-01 FOR POWER SUPPLY SCHEMATIC (TYPE &) ‘any oF license to use, the subject malter of the rawing any design or technical formation shown tneregn or any righ reproduce iis rawing or any par uatactute corporation's wit i to reproduce this drawing is grantes Figure 5-8 Power Supply Assembly 5 for A00719702 D ips pumge rane nee ames aware
64 = Skydiver
Figure 5-8 Power Supply Assembly Parts List
ATARI’
= —
| Item | Part Number | Qty. | Description |
| 1 | A009266-01 | 1 | Power Supply Base Weldment Assembly |
| 2 | A006886-01 | L | Transformer Termination Assembly "Type B" |
| 3 | 29-053 | 1 | Cap., Sprague Electrolytic 26,000uf @ 15V |
| 4 | 78-70501SC | 1 | Brkt., Cap. Mtg. Sprague #4586-48 |
| 5 | A006555-01 | 1 | P.C. Board Rectifier |
| 7 | 79-4411004 | 5 | Fuse Holder, Panel Mounting |
| 8 | 41-2003 | 1 | Filter, Power Line, 5 AMP |
| 9 | 4006958-01 | A/R | Yolt Sel Block 95V |
| 10 | A006958-02 | « | Volt Sel Block 110V |
| li | A006958-03 | " | Volt Sel Block 205V |
| 12 | A006958-04 | ° | Volt Sel Block 220V |
| 13 | 78-2708 | 1 | Grommet ,Plastic |
| 14 | 72-1810S | 9 | Screw Pan Hd., #8-32 x 5/8"Lg. |
| 16 | 75-048 | 9 | Washer, Split-Lock #8 |
| 17 | 75-9188 | 9 | Nut Hex #8 |
| 18 | 75-0188 | 8 | Washer Flat #8 |
| 19 | A007192-01 | 1 | Power Switch Termination |
| 20 | A007444-01 | 1 | Power In Harness |
| 21 | 46-2028002 | 1 | Fuse, 8 AMP, 230V, 3 AG Slow Acting |
| 22 | 46-201251 | 2 | Fuse, 2 AMP, 125V, Slow Acting |
(a
ELE
AY WERICATE ALL PIVOT AND SUDE POINTS WITH
MOLY KOTE G-n PASTE LUBRICANT - ATARI P/N 78-1709
NOTE:
A Figure 5-9 Rip Cord Assembly A0330084
_ Figure 5-9 Rip Cord Assembly
- Parts List
ATARI
| 7 | Item | Part Number | Qty. | Description |
+
| 1 | 033115-01 | 1 | Handle, Control | |
| 2 | AQ33123-01 | 1 | Bracket, Control Assy | |
| 3 | 033109-01 | 1 | Plate, Slide | |
| — | 4 | 007371-01 | 1 | Spacer, Switch |
| 5 | 78-3001035 | 2 | Spring, Extension | |
| a | 6 | 033112-01 | 4 | Pin, Stop |
| _ | 7 | 73-3008 | 10 | "E' Ring, % Shaft |
| 8 | 72-14108 | 6 | Screw, Mach, Phillips Pan Hd., #4-40UNC-2A x 5/8 LG | |
| 9 | 007859-01 | 3 | Switch | |
| 10 | 75-054 | 6 | Washer, Lock, #4 (Star) | |
| 11 | 033113-01 | 2 | Stop, Neoprene | |
| 12 | 033110-01 | 1 | Pin, Spring | |
| 13 | 75-07050 | 2 | Washer, Nylon | |
| 14 | 78-1709 | A/R | Lubricant, Paste, Molykote G |
HL
Figure 5-10 On-Off Switch Assembly A006449-01
68 © Skydiver
NOTES
Z\\ POSITION HEX NUT APPROX. AS SHOWA.
SWITCH 1S INCLUDED ‘WITH
SWITCH,
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction forbidden wilhout the Spec, writen permission of Alar. inc. Sunnyvale, Caitornia” This draw ‘issued.
{o reprosuce this Urawing ts granted Orie subject malter heres! uniess by writes agreement ‘with of wnitten permission rom the corporation. Lyd
Figure 5-10 On-Off Switch Assembly Parts List
ATARI’
$$ Part Number DESCRIPTION
61-062A Toggle Switch, DPST Carling Switch #2GK54 006450-01 1 MTG Plate, On - Off Switch
al —_—____|
NOTICE TO ALL PERSONS AECEIVING THIS DRAWING CONFIDENTIAL: Reproguction forbidden withoot the Specitic written permiseion of Alar, Inc," Sunnyale, Caitornia. This drawing 1s only conditionally issued, and either receipt nor possession thereo! confers or transfers {ny right in, oF license fo use, the subject matter of the ‘rawing or any design or technical information shown, thereon, nor any right to reproduce tnis arawing oF any part thereof, except for manutaclure by vendors 0! Alar, Incor- Porated and tor manufacture under the corporation's wnt fen license, no right to reproduce this drawing is granted ‘of the subject alter inereot uniess by wiliten agreeme wih or waitten permission from the corporation
Figure 5-11 Rectifier Board Assembly A006555-01 A006555
CR2
Figure 5-11 Rectifier Board Assembly Parts List
ATARI’
Fite L Part Number Qty. | Description
1 006556-01 P.C. Board 2 31-MR750 2 Diode, MR750 CR1,CR2
pf |
Tous Row xow? Jews nwo [rroveToR [anaPcm [eAPReiToRlEAPAcs Toe! Oo é a x L2 x © x m x = K a Fa x € % ~ X x oi % x_| S x ® x_| a x
x
x
x 7 x
z | * x x | L xf
ra x
- | *
* 7 | iB x [x 3 %
ic Der woxcmupastuvwsy RINE oe ae 2SasPr oswnrawwene Row 2 Row 4 Ss
- SEE NOTE OnE a No See Nove one,
\ use Toot # Toz0e12-01 FOR MOUNTING FASTENER,
Figure 5-12 RF Shield PCB Assembly D A033046-01
A. Figure 5-12 RF Shield PCB Assembly Parts List ATARI"
= litem] Part Number Qty. Description 4
| 7 | 1 | 030835-01 | 1 | P.c. Board | ||
| 2 | 2D-1016 | 28 | Capacitor, Mono, 0.luf, 50V | |
| 3 | 41-3003 | 12 | Inductor, 10QuH | |
| _ | 4 | $2-003 | 17 | Jumper, .600 Centers |
| i | 5 | 75-E6106082 | 3 | Wingscrew, #6-32 x 1/2 Lg |
| — | 6 | 75-992501 | 3 | Fastener, 1/4 Turn, #6-32, Stainless Steel | ||
| — | 7 | 79-817222 | 1 | Connector, 44 Pin P.c. Mount | ||
| 7 | 8 | 030868-01 | 2 | Mount, Connector |
rere Preere Pred VERS on Ro)
MoD \ L os Fetes rend
MODIFICATIONS: TO 009788-01 REV'A’ PC. BDS.
- ADP B30 OHM RES CRBZ> TO VIDEO SUMMING ROTGE,TO Als RERSONS ne CIRCUIT AS SHOWN ‘;
Figure 5-13 Skydiver PCB Assembly A009787-01
A ATARI’
Figure 5-13 Skydiver PCB Assembly Parts
Version -01 Item | Part Number | Qty. Description 1 009788-e1 1 | P.C, Beard 2 10-5100 2 | Res., Car, Comp., 1/4W, 5%, 100hm 6,8 3 10-5220 2 wow ag RST 4 10-5101 L 100 7 RRB 5 10-5151 4 150." R48, 49, 75,76 6 10-5331 8 3307 RIT,18, 82 7 10-5471 16 So "4700" R16, 12, 50-58,
13,74, 77-79 8 10-5684 1 oo "880 R22 9 10-5102 a "oon es R1,2, 11, 12,14
20,21, 26,71, 72,83 10 10-5152 2 ” 1.5K R62, 63 a 10-5182 3 " 1.8K Rs-61 2 19-5222 1 * 2.2K RIS 13 10-5332 1 " 3.3K R27 4 10-5392 1 ” 3.9K R13 15, 10-5472 2 4.7K R3, 10 16 10-5862 2 5.6K R6B, 69 " 10-5103 26 * 8 qoK n RA, 9, 23-25,
29-47, 73,74 18 10-5683 2 noon ow room 68K R67, 70 19 10-5104 2 | Res., Car. Comp., 1/4W, 5%, 100K Ohm R64, 80 22 19-8D9W2PO 1 | Res., Wirewound, 20W, 2 Ohm R81 25 19-315254 2. | Trimpot, 250K Onm 65,66
Item | Part Number _| Qty. Description 29 21-101332 2 |Cap., Mylar, 100V, .0033uf ©58, 59 30 21-101103 2 |" 1 9 -Olut 72,73 a 21-101224 1 |Cap., Mylar, lov, — .22uf cx 34 24-250105 1 | Cap., Flectrolytic, 25, tut C55 35 24-250106 1 | " " 10ut ces 36 24-250226 2|" . " 22uf 74,75 37 24-250227 2 | Cap., Electrolytic, 25V, 220uf 266,68 38 | 38 | 40 27-250104 | 61 | Cap., Ceramic Disc, 25V, -tur C121, 26-54, 56,57,
60-65,67, 73,76 43 28101330 2 | Cap., Dipped Mica, 100V, 3apf 22,25 44 28- 101680 2 | Cap., Dipped Mica, 100V, 68pf C23, 24 47 | 48 31-1N914 5 | Diode, 1N914 CRLAT 49 31-1N100 2 | Diode, 1N100 CR2, 3 BL 58 34-2N3643, 7 | Transistor, 2N3643 QL-4,7, 8, 12 oa 34-2N6044 9 | Transistor, 2N6o44 5,6, 9 1, 13-16 oT 58 37-7400 3 | Integrated Cireuit, 7400 7, K9, L9 59 37-7402, 3 - "7402 6, M8, L10 60 37-7404 5 7404 H4, BS, M5, N10, H11 61 37-74H04 1 74HO4 HO @ 31-7408 5 7408 E3,F3, D4, BS, K12
- 31-7410 1 7A10 BE 64 37-7414 1 74M clo 65 37-7420 2 7420 NS, D6 66 37-7427 2 a 7427 F4,A5 67 37-7430 1 ” 7430 a4 68 37-7432 7 i 7432 D3, H3, £5, PS, DT, F8,
M9 69 37-7437 1 raat F9 70 37-7450 1 7450 Mio a 37-7474 1 7404 BO 72 97-74874 1 74874 Eg 13 37-7475 2 7475 M6, P6 74 31-7476 1 . 71416 K10 © ames Commins Conary
ATARI’
Figure 5-13 Skydiver PCB Assembly Parts List
Version -01 Item Part Number Qty. Description Item Part Number Qty. Description 75 37-7483 2 | Integrated Cireuit, 7483 K3,K4 10 | 79-4040 1 | Socket, 40 Pin, Med. Insert 63/4 76 37-7486 3 a 1 7486 35, J6, MAL 121 a 37-7490 1 7490 BT 122 78 37-TALSI5L a T4LS181 E10 123 79 37-74153 2 74158 310, FLL 124 | 90-102 1 | Crystal, 12.096 MHz Yl 80 37-74156 1 74196 H10 125 81 37-141 8161 2 7418161 6, A8 126 82 3T-TALS163 8 . " T4Ls163 13, M3, N3, P3, L4, M4, 127
N4, PA 128 | 90-6001 1 | Microprocessor, 6800 63/4 83 37-74164 2 74164 Ju, Ki 1z9 | 90-6002 1 | Trans., MPQ6842 3 84 37-74L8165 8 T4L8165 F7, H7, J7,K7, 7, M7, 130 | 90-7020 8 | Ram, 211028 H/J1, 31, K1, K/LA, LA,
N7, P7 M1, N1, PL 85 37-74174 4 74174 M2, P2, J3, C6 131 90-7002 1 | Ram, 6810 BL 86 37-74175 x 74175 ET 132 87 37-74195 1 74195 HG 133, 88 37-74LS273 1 74L9273 Aq 134 89 37-8728 2 8728 Al, A/B2 135 | 00640001 1 | Syne Prom ES 90 37-8797 2 897 12,2 136 91 37-9301 3 9301 E4, K8, L8 137 92 37-9312 2 9312 cll, D1 138 93, 37-9316 6 9316 8, DS, J8, C9, DY, J9 139 030868-01 2 | Mount Connector 94 37-9322 5 "9322 H/J2, J/K2,K/L2, K6, 140
16 141 95 37-9334 3 9334 ALL, F12, 12 142 96 37-LM324 1 LM324 Nu 143, | 033163-01 1 | Skydiver Graphics HS 97 37-4066 1 "4066 Nz asa | 033176-01 1 "Motion 1 Ls 98 37-556 1 | integrated Circuit, 556 K13 145 | 033177-01 1 | Skydiver Motion 2 KS 39 146 100 ut 101 148 102 62-001 1 | Switch, SPST, Momentary, SW2 149 | 033168-02 1 | Skydiver Prom 28001 a0 103 66-L14PIT 1 "x4, Dip, SW3 Diz 150 | osa16s-02 1 " "30001, E2 104 66-118PIT 1 "<8, Dip, SWI FIO 151 033170-02 1 38001, D/E2 105 1s2 | 033171-02 1 78001, c/pa, 106 153 033172-02 1 2800M. a/KO 107 1st | 033173-02 1 3000M K/LO 108 72-1608C 2 | Screws, Pan Hd, Phil, 6-32 x 1/2 LG, Cres. 15s | 033174~02 1 380M 12 109 75-016 2 | Washer, Flat, #6 asé | 038175-02 1 " " 7800M F2 110 75-056 2 | Washer, Lock, Int. Star, #6 157 an 15-916C 2 | Nut, Hex, 46-32, Cres. 158 | 033179 -02 1 3400L HO ug 159 | 033180 -02 1 3C00L, D/z0 113 160 033181 ~02 1 - " 7C00L, E/FO 4 161 4s 78-0601 1 | Heatsink (M323) 162 | 033183-02 1 ‘3400M BO 116 78-1605 1 | Silpad (M323) 163 | 033164-02 1 3CooM Do re 164 02 1 ” "-7C00M co
ATARI
Figure 5-13 Skydiver PCB Assembly Parts List Item | Part Number | Qty. | Description 1 009788-01 1 | P.C. Board 2 10-5100 2 | Res., Car, Comp,, 1/4W, 5%, 100hm 6,8 3 10-5220 2 nos 6" 22 Ohm 4 10-5101 1 " 100 R28 5 10-5151 a] 150 Rag, 49,75,76 6 10-5331 3 " 330 RIT, 18, 82 1 10-5471 16 some "470" RIG, 19, 50-58,
73, 74,1 7-79 8 10-5681 1 ” ” 680 R22 8 10-5102 u " "1K R1,2, 11,12, 14
20,21,26, 71, 72,83 10 10-5152 2 ” 1.5K" R62, 63 ul 10-5182 3 " 1.8K 59-61 wz 10-5222 1 ” 2.2K R15 rey 10-5332 1 7 3.3K kar 4 10-5392 1 * 3.9K Ris 45 10-5472 2 ” 4.7K" R820 16 10-5562 2 ” 5.6K" R68, 69 W 10-5103 26 " "WOK" RA, 923-25
29-47, 73,74, 8 10-5683 2 Hoon on “on 68K" RET, 70 19 10-5104 2 | Res., Car, Comp., 1/4W, 5%, 100K Oam R64, 80 22 19-spewzPo | 1 | Res., Wirewound, 20W, 2 Ohm REL 25 1931525 2 | Trimpot, 250K Ohm R65, 66 © iiarre Communications Gompary
Version -02 Item | Part Number | Qty. Description 29 21-101332 2 | Cap., Mylar, 100V, .0033uf 58, 59 30 21-101103 2 |" so -O1uf 72,73 31 21-101224 1 | Cap., Mylar, 100V, .22uf 70 34 24-250105 1 | Cap., Electrolytic, 25v, luf_ C55 35 24-250106 1 " " "lout C69 36 24-250226 2)" " "aut C74, 75 at 24-250227 2 | Cap., Electrolytic, 25V, 220uf C66, 68 40 27-250104 61 | Cap., Ceramic Disc, 25V, .luf C1-21, 26-54, 56, 67,
60-65, 67,71, 76 43 28-101330 2 | Cap., Dipped Mica, 100V, 3apf 22,25 44 28-101680 2 | Cap., Dipped Mica, 100V, 68pf 23,24 48 S1-1N914 5 | Diode, 1N914 cR1, 4-7 49 31-1N100 2 | Diode, 1N100 cr2.3 53 34-2N3643 7 | Transistor, 2N3643 Ql-4,7,8,12 54 34-2NG044 9 | Transistor, 2N6o44 Q5, 6, 9-11, 13-16 58 37-7400 3 | Integrated Circuit, 7400 C7, K9, L9 59 37-7402 3 " 7402 E6, M8, L10 60 37-7404 5 " 7404 H4, BS, M5, N10, H11 61 37-7404 1 " » TaHod 9 62 37-7408 5 “ 7408 £3, F3, D4, B8, K12 63 37-7410 1 a 7410 BG 64 37-7414 1 x ala c10 65 37-7420 2 " 7420 N5, D6 66 37-7427 2 ” 7427 F4,A5 67 37-7430 1 " 7430 4 68 37-7432 7 7 7432 D3, H3, E5, P5, D7, F8, M 69 37-7437 1 * 7437 F9 70 31-7450 1 ” 7450 M10 a 37-7474 1 E " rara Bo 72 37-74874 1 " 74874 9 73 37-7475 2 ” 7815 M6, P6 "4 37-7476 1 . " 1a76 K10
Figure 5-13 Skydiver PCB Assembly Parts List Version -02 ATARI Item |__Part Number | Qty. Description Item | Part Number | Qty. Description 15 | 37-7483 2 | Integrated Circuit, 7483 Ka, K4 120 | 79-42040 1 | Socket, 40 Pin, Med, Insert 3/4 76 | 37-7486 3 " "7486 35, J6, MLL 121 1 37-7490 a ” 7490 BI 122 we | a7-7408151 1 ” " qaLsis B10 123 79 37-74153 2 ” "74153 J10, FL 124 | 90-102 1 | Crystal, 12.096 MHz YL 80 | 3774156 1 : "74156 uo 125 al 37-74 LS161 2 " " qaLsi61 6, A8 126 82 37-T4LS163 8 . "7418163 L3, M3,N3, P3, La, Ma, 127
N4, Pa 128 | 90-6001 1 | Microprocessor, 6800 3/4 83 37-74164 2 . "74164 Ju, KIL 129 | 90-6002 1 | Trans., MPQ6842 cs 84 37-T4LS165 8 " " qaLsi6s F7, 87, J7,K7, La, M7, 130 | 90-7020 8 | Ram, 211028 B/J1, 31,1, K/L1, L1
Nz, P7 M1,N1, PL 5 | ar-rai74 4 qaiTa M2, P2, J3, C6 131 | 90-7002 1 | Ram, 6810 BL 86 87-74175 1 74175 ET 132 87 37-74195 1 " "T4195 H6 133 sa | 37-74L8273 4 ° " 7aLsa73 AT 1st 89 31-8728 2 "rae AL, A/B2 13s | 006400-01 1 | Syne Prom ES 90 37-8797 2 8T97 12, N2 136 a1 | 37-9301 3 9301 4, K8, LS 137 92 31-9312 2 ” " gai2 cu, pi 138 93 37-9316 6 ” "9316 C8, D8, J8, C9, D9, J9 1s9 | 030868-01 2. | Mount Connector 94 37-9322 5 " "9322 H/J2, J/K2, K/L2, K6, 140
16 M41 95 | s7-gaad 3 " "9334 ALL, Fl2, H12 142 96 37-LM324 1 " " LM324 Ni 143 033163-01 1 | Skydiver Graphics HS, 97 37-4066 1 * "4066 N12 4a | 0agi76-o1 1 "Motion 1 15 98 37-556 1 | Integrated Circuit, 556 Kis 145 | 033177-01 1 | Skydiver Motion 2 K5 99 146 100 aat 101 148 102 62-001 1 | Switch, SPST, Momentary, sW2 149] o3si64 -02 1 | Skydiver Rom 1 EL 103 66-114PrT 1 v's "4, Dip, SW DAZ 150 | 033165 -02 1 nom DL 104 66-118PIT a "x8, Dip, SWI F10 isi | 033166 -02 1 "4 3 cL 105 152 033167 -02 1 | Skydiver Rom 4 Fl 108 72-1608C 2 | Screws, Pan Hd, Phil, 6-32 x 1/2 LG, Cres. 109 75-016 2 | Washer, Flat, #6 uo 75-056 2 | Washer, Lock, Int. Star, #6 a1 | 75-916c 2 | Nut, Hex, #6-32, Cres, ua 11s | 78-06001 1 | Heatsink (Lat323) us 78-1605 1 | Silpad (LM323) ut
orcs
- arcs
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL, Reproduction forbidden without Specitic written permission of Atari. Inc." Sunny Galfornis’ This orawing is only conditionally issued, and either fecelpt nor possession tered! confers or anste's, fany right in.or license to use, the subject matter of the drawing or any design or technical. information. shown thereon, nor any right toreproduce this drawing o7 any part thereo! except for manwiacture by vendors 91 Ata, Incot: porated and for manutacture under the corporation's writ {en license, no right to repreduce this drawing is granted ‘or the subject matter thereat unless by writen agement wit oF wetten permission from. the corperatlon Figure 5-14 Front Bezel Assernbly A007637-01 thru -07 D
Figure 5-14 Front Bezel Assembly Parts List
ATARI
| Item | Part Number | Qty. | Description |
| 1 | 004328-01 | 1 Bezel | |
| 2 | See Below | 2 | |Ring |
| 3 | 004331-01 | 2 Coin Shield | |
| 4 | 004332-01 | 2 Primary Coin Chute | |
| 5 | 004327-01 | 2 | Bearing, Scavenger Button |
| 6 | 004329-01 | 2 | Clamp, Price Plate |
| 7 | See Below | 1 |Price Plate | |
| 8 | 73-3009 | 2 | Retaining "C" Ring, Truarc #5103-37 |
| 9 | 72-1604S | 4 Mach. Scr., 6-32 x 4 Lg. Pan Hd., Phil | |
| 10 | 75-046 | 2 Washer, #6, Split-Lock . | |
| ll | 75-9914001 | 6 Self-Threading Nut, Tinnerman #SR188006 |
[Ase Nol =rem 2 ETeM 1 [DENSMINATION| =O: [SO4SSo-o1 SSuBGS- ol | 25¢ [ -c2 [cousso-o1 foous4s-ce| SFR =os 1009153 -0) [COFsHS-o4 | 1 BM =Oy [oCUsso-o1 joousds-os | 1 KR -OB8 [SO9S2ZO-Gl |CO4R4S-O8 | 10OY Oe _[SO7752-O1 [SOs =H E02! IOP =o7 looTisa-o1looususo7leo¢ AUST |
© 4 warner Communications Company
-3)_.080 @er) LO BPRS rise \ 1 . (3B MOVEMENT ZEQO. WHEN ENER SIRES, il (Hin)
(BBC stance De ° “ _ t | wv. 2a R- f So — (eae nowese-e1) li ol
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING Bl CONFIDENTIAL: Reproduction forbidden without the | written permission of Alar Sunnyvale, ia. This drawing 1s. Only conditionally issued, and ‘receipt nor possession theveot conters or transiers ny right in, of license to Use, the subject matter of the Grawing of any design or technical information. shown NOTES: thereon, not any right to cepraduce this drawing or any part \ ‘hereo! excep! for manvlaclure by venders of Alar, Incor: DIMENSIONS SHOWN ARE OIN'S REGO. TO porated and for manufacture under the corporation's wnt
EQUIPMENT 1 FIELD AND PRODUCTION with or written permission from the Corporation.
BEAK @ DELoRT ALL SHARP CORNERS B, DINENS ONS TAKE Feom TOXED Paget, OMENSIONS WITH ASTIIC (¥) ABE SPECIFIED DIMS REGUICED IN TOOLING BY ENGENELENG To uve PACT 1oTeacuavee WIPE BOUT parr 4 cole DATA lovoe #2 , som ees, CoeeewT ZOO me MAX. (FEZ ATA! OWE MOOTETD-O}) S MPR COW beeH We
- 2.09
(venor)
Detail of Relay Coil (A007639-01)
COIL NES
fees | 50a —*d CURRENT | 2ZOOma MAX
Figure 5-18 Coin Lockout Assembly A030362.01 A
2Pics NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction. forbidden without the specitic written permission of Atarl Sunayvate, California’ This drawing 1s only condi issued, 3nd neliner receipt nor possession thereo! cont any right in, or license 10 use, the subject matter of the ‘rawing oF any sesign or technical information shown thereon, nor any right to reproduce nis arawing or any part thereof, except for manutacture by vendors of Aan, incor porated and for manutactyre under tne corpo fen ticense, no right to reproduce this drawing is granted fr the subject matter thereo! uniess by written agreement With or witten permission trom te corporation,
ITEM FART NO.} DESCRIPTION QTY]
| 1 | [OOusSs2-OifSwitck MTG | PLATE | v |
@_S jes-44ic [Switcr, omeon C-543-3] 1
| 4 | P2-Hm 4412 [SCRMS,24-4O RULERS TAPP] | 2 |
Ss
| 6 | [008824-01] | WIREFORM , CHERRY | 1 |
igure 5-16 Coin Switch Assembly A007640-01 D
a
TV MONITOR SERVICING
INFORMATION
This chapter provides servicing information taken from the Motorola and TEC service manuals. Each manual has been reprinted by permission of the respective monitor manufacturer.
Your game will include either the Motorola or TEC monitor, depending on their availability during production.
MODELS M5000-155 M7000-155
MOTOROLA Service Manual
A. GENERAL INFORMATION This manual contains information on the M5000/M7000 monitor series and the +5 volt logic power supply. The M5000 uses a 19-inch CRT and the M7000 uses a 23-inch CRT. All CRTs are of the magnetic deflection type with integral implosion protection.
All monitor power supplies are capable of producing both +73 and +12 volts regulated from either 115-volt or 230-volt AC input to the transformer primary. All monitor variations described herein require a composite video input signal.
SAFETY
- Safety procedures should be developed by habit so that technicians rushed with repair work automatically take precautions.
- A good practice, when working on any unit, is to first ground the chassis and to use only one hand when testing circuitry. This will avoid the possibility of carelessly putting one hand on chassis or ground and the other on an electrical connection which could cause a severe electrical shock.
- Extreme care should be used in handling the picture tube as rough handling may cause it to implode due to atmospheric pressure (14.7 Ibs. per sq. in.). Do not nick or scratch glass or subject it to L any undue pressure in removal or installation. Input and output connections for the monitors are made through a 12-pin connector plug located at the rear of the chassis. Inputs consist of composite video, audio, and 115/220 volt AC three-wire.
All monitors employ: four stages of video amplification, a two-stage sync separator, a two-stage vertical integrator, a four-stage horizontal sweep circuit, a three-stage vertical sweep circuit, a one-stage spot kill, a one stage blanking amplifier; and a regulated, full-wave bridge power supply.
Model Breakdown Chart
Model Video Input 19" CRT 23” CRT
IM5000-155, Composite x
IM7000-155 Composite
- An isolation transformer should always be used during the servicing of a unit whose chassis is connected to one side of the power line. Use a transformer of adequate power rating as this protects the serviceman from accidents resulting in Personal injury from electrical shocks. It will also protect the chassis and its components from being
84 & MOTOROLA Data Products _ caroistream,iuinois 60187 PART NO. 68P25253A47 COPYRIGHT 1977 BY MOTOROLA, INC. PRINTED INUS.A.
damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.
5, Always replace protective devices, such as fishpaper, isolation resistors and capacitors and shields after working on the unit.
- Before returning a serviced unit, the service technician must thoroughly test the unit to be certain that itis completely safe to operate without danger of electrical shock. Do not use a line isolation transformer when making this test. a HOPOHMVOLT (OF HIGHER) AC VOLTMETER NOTES: 1. REPEAT EACH CHECK WITH THE LINE CORD REVERSED IN THE POWER OUTLET
- METER READING MUST NOT EXCEED 7% VOLTS AC “HOT” LEAD OF METER TO EACH EXPOSED PART OF CABINET, AS WELL AS THE CABINET GROUND LEAD OF METER TO ANY EARTH GROUND SUCH AS A COLD WATER PIPE Sy
Voltmeter Hook-up for Safety Check In addition to practicing the basic and fundamental electrical safety rules, the following test, which is related to the minimum safety requirements of the Undemriters Laboratories, should be performed by the service technician before any unit which has been serviced is installed in a game again.
A 1000-ohm-per-volt AC voltmeter is prepared by shunting it with a 1500-ohm, 10-watt resistor. The safety test is made by contacting one meter probe to any portion of the unit exposed to the operator such as the cabinet trim, hardware, controls, knobs, etc., while the other probe is held in contact with a good “earth” ground such as a cold water pipe.
The AC voltage indicated by the meter must not exceed 7% volts. A reading exceeding 7% volts indicates that a potentially dangerous leakage path exists between the exposed portion of the unit and earth ground. Such a unit represents a potentially serious shock hazard to the operator.
The above test should be repeated with the power plug reversed, when applicable.
Never reinstall a monitor which does not pass the safety test until the fault has been located and corrected.
Table 6-1 Motorola Monitor Electrical Specifications = MODEL M5000-155 MODEL M7000-155
PICTURE TUBE 19” measured diagonally (48.2 cm); 23” measured diagonally (58.4 cm); 184 sq. inch viewing area (1188 sq. cm); | 282 sq. inch viewing area (1820 sq. cm); 114° deflection angle; integral 110° deflection angle; integral implosion protection; P4 phosphor implosion protection; P4 phosphor standard standard
| POWER INPUT | 115/230 VAC, 110 Watts (nominal); 60 Hz provision for 230 VAC, 50 Hz | | |
FUSES M5000-155, M7000-155—0.8A
+73 VOLT SUPPLY Electronically regulated over AC inputs from 103 VAC to 130 VAC, or 260 VAC to 260 VAC
| VIDEO INPUT | 0.5 Volts to 2.5 Volts P/P maximum, composite for 50V at CRT | | |
| RESOLUTION | 500 lines at picture center | | |
| PINEARIT. Within 3%, measured with standard EIA ball chart and dot pattern
Table 6-1
17KV (nominal) HIGH VOLTAGE Motorola Monitor Electrical Specifications
HORIZONTAL BLANKING INTERVAL 11 microseconds typical (includes retrace and delay)
SCANNING FREQUENCY Horizontal: 15,750 Hz+500 Hz; Vertical: 50/60 Hz
ENVIRONMENT Operating temperature: 10°C to 55°C (ambient) Storage Temperature: —40°C to +65°C Operating Altitude: 10,000 ft. maximum (3048 meters) Designed to comply with applicable DHEW rules on X-Radiation CSA certified for use in coin-operated amusements in a combustible enclosure UL listed under specification 1410 (electronic components)
TYPICAL DIMENSIONS (35.8 x 46 x 37.6 cm) 14.11" H, 18.18” W, 14.83" D 16.72” H, 21.56" W, 16.18” D (42.4 x 54.7 x 41 cm)
Specifications subject to change without notice.
B. SERVICE NOTES
Circuit Tracing Component reference numbers are printed on the top and bottom of the three circuit cards to facilitate circuit tracing. In addition, control names are also shown and referenced on the schematic diagram in this manual.
Transistor elements are identified as follows: E—Emitter, B—Base, C—Collector.
Component Removal Removing components from an etched circuit card is facilitated by the fact that the circuitry (copper foil) appears on one side of the circuit card only and the component leads are inserted straight through the holes and are not bent or crimped.
It is recommended that a solder extracting gun be used to aid in component removal. An iron with a temperature-controlled heating element would be desirable since it would reduce the possibility of damaging the circuit card foil due to over-heating.
The nozzle of the solder extracting gun is inserted directly over the component lead and when sufficiently heated, the solder is drawn away, leaving the lead free from the copper foil. This method is particularly suitable in removing multi-terminal components. CRT Replacement Use extreme care in handling the CRT, as rough handling may cause it to implode due to high vacuum pressure. Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Use goggles and heavy gloves for protection. In addition, be sure to disconnect the monitor from all external voltage sources.
- Discharge CRT by shorting 2nd anode to ground; then remove the CRT socket, deflection yoke and 2nd anode lead.
- Remove CRT from the front of the chassis by loosening and removing four screws, one in each corner of the CRT.
Adjustments A non-metallic tool is recommended when performing the following adjustments.
Regulator Adjustment
- Connect the monitor to an AC line supply; then adjust supply to 120 volts (240 volts in some applications).
- Apply test signal to proper input. Signal should be of same amplitude and sync rate as when monitor is in service.
- Adjust HOR. SET coil L1 until display is stable.
- Connect a DC digital voltmeter or equivalent precision voltmeter to the emitter of the regulator output transistor, Q17, or any +73 voit test point.
- Adjust the 73V ADJUST. control, R93, for an output of +73 volts, Do not rotate the control through its entire range; damage to the monitor may result.
- When adjustment is complete, the AC line supply can be varied between 103 and 130 volts AC to check for proper regulator operation. With the regulator operating properly, changes in display size should be negligible.
Horizontal Hold/Oscillator Adjustment Adjust the core of HOR. SET coil L1 until the horizontal blanking lines are vertical or the CRT display is stable (synced).
Vertical Height/Linearity Adjustment
- Connect a test generator whose output is similar to the display signal normally used.
Motorola Monitor Circuit Board in Service Position Figure 6-1
- Rotate the vertical size control, R60, until the smallest display is obtained.
- Adjust the vertical linearity control, R64, until the top and bottom of the test pattern is equally spaced.
- Readjust R60 until the desired display height is obtained.
- Readjust R64, if necessary, as in Step 2 above.
Focus Adjustment The best overall focus of the display is obtained by adjusting the focus control, R42, for best focus ata point which is near the center and approximately 1/3 down from the top of the display.
Monitor Servicing The monitor circuit board may be installed in a service position to provide easier access to the circuit foil when servicing the monitor (see Figure 6-1).
C. THEORY OF OPERATION Power Supply The power supplies are transformer-operated, full-wave, regulated supplies which maintain constant output voltages for input line variations of 103 volts AC to 130 volts AC, or 206 volts AC to 260 volts AC. Regulation of the output voltages is accomplished by using positive feedback through the integrated circuit reference amplifier.
+73 Volt Supply (See Figures 6-3,6-4) When the +73 volt supply attempts to increase, the voltage at pin 3 of IC1 will increase, while the voltage at pin 2 remains constant due to D20. The increasing voltage at pin 3 will cause the output voltage of the reference amplifier (pin 6) to increase the forward bias of Q19. The collector voltage of Q19, forward bias of Q18, and the base current of Q17 will all decrease. The resultant proportional increase of Q17 collector-to-emitter voltage will cancel the attempted output voltage increase.
When the +73 volt supply bus attempts to decrease; the voltage at pin 3 of IC1 will decrease while the voltage at pin 2 remains constant. The decreasing voltage at pin 3 will cause the reference amplifier output voltage at pin 6 to decrease the forward bias of Q19. The collector voltage of Q19, the forward bias of Q18 and the base current of Q17 will increase. The collector-to-emitter voltage of Q17, which is in series
\Vi0e0 GND COMPOSITE EMITTER VIDEO
INPUT FOLLOWER
Ig fi rq
INPUT HORIZ.
| noni | roniz | Honiz. | oriz |
| 5 | sc | OnIVER |
115/230 REGULATED 7M [a] {= | see voursac power | —o+12v SUPPLY
spor spanning |_| "ANPL. re
VERT. VERT.
| SYNC | sync. | Pats | veer | VERT. |
| SEPARATOR | ANPL. | { Iwrecnator | Rd | Osc. |
Figure 6-2 Motorola Monitor Block Diagram vert, ORIVER
R84 150
U7 ABW REGULATOR
gus Ble REG, BUFFER
Figure 6-3 +73 Volt Supply Circuit with the output, will decrease proportionally to the attempted decrease in the outbut bus. NL Ea ROM EMCTIER 1 :
| A! | ! | | OF 17 |
Resistor R84 shunts a portion of the output 1 EXISTING VERTICAL
| is | dissi | ithi | SAWTOOTH WITHOUT |
current around Qi7 so less power is dissipated within VERT.PARABOLA
the device. Resistor R82 is the current-limiting resis- ADDED tor for Q18, and R86 controls the leakage current of ' . PARABOLA PU ND Q17. Resistors R83 and R85 are the collector load for VeRTicaL SAWTOOTH
| 7 | i | ADDED TOGETHER, |
Q19, and R88 and R87 Provide an emitter voltage for HENCE PRODUCING THE
Qi9 within the range of IC1’s output voltage var- REQUIRED VERT, iations. Capacitor C45 filters high frequency var- ORIVING SIGNAL iations from the voltage at pin 7 of IC1, and C49 is a " " : 7 Miller-effect capacitor which eliminates instability. Figure.6-4 Motorola Monitor Vertical Drive Waveform
+73V 4150V co a gla HY g __» wy 1K sw +015 ==
i oS P/O i emir Tee COMPOSITE vineo 12 FOLLOWER INPUT 44? log 63
GNO 2 22 S02 = = lis Veo ONO, R6
contrast
T0633 clo
0,22 03 viDeo SS 62 152348
(CATHODE); ViA 878 ¥ —
To gio To Qi EMITTER coutectoR
Figure 6-5 Motorola Monitor Video Amplifiers and Output Circuit
Capacitor C32A filters horizontal frequency variations from the output bus,
Resistor R91 provides bias current for D20, and the value of R99 presents an impedance from pin 2 of C1 to AC ground (through D20). Capacitor C46 couples high frequency voltage variations, which occur at the output bus, back to pin 3—preventing oscillations for proper operation of the reference amplifier. Resistors R92, R93, and R94 provide voltage division such that the adjustment of R93 can be set equal to the voltage of pin 2 of IC1. Resistor R95 provides bias current for D21 and also provides the +12 volt output. Diode D23 is necessary to temperature-compensate for variations within D21. Capacitor C32B filters AC variations from the output of the full-wave bridge.
Video Amplifiers and Output (See Figure 6-5) The composite video signal is coupled to the emitter-follower Q1 through the input connector P1 and capacitor C1. Transistor Q1 is a buffer stage which matches the impedance of the signal source to the video preamplifer and the sync separator stages. Resistor Ri is a terminating resistor for the video signal source, and resistors R2, R3, R4, and R5 form the biasing network for the stage. Capacitor C2 bypasses higher video frequencies to ground. The composite video signal is coupled from the emitter of Q1 to the sync separator Q10 through C33 and to the contrast control R6 through C47.
The contrast control varies the amplitude and couples the composite video signal to the base of Q2 through capacitor C3. Transistors Q2 and Q3 are complimentary, direct-coupled, common emitter amplifiers. The voltage gain (approximately 12) of the preamplifier stage is controlled by the feedback arrangement of R9, R10, R11, and R12. Resistors R7 and R8 provide the base bias voltage for Q2. Capacitor C48 is used for high-frequency peaking.
The output of the video preamplifier stage is coupled to the video output stage through capacitor C4. Diode D2 clamps the video signal to approximately +0.7 volts (DC restoration) when a sync pulse turns on the sync amplifier Q11, The video output stage is connected in a cascade configuration. Transistor Q4 is a common emitter amplifier and Q5 is connected in a common base arrangement. Capacitors C7, C8, and resistor R16 are used for highfrequency compensation, and resistor R18 controls the gain of the stage to approximately 47. Diode D3 maintains the base of Q5 at +6.2 volts, while capacitor C5 filters the video signal variations from the base voltage. Resistor R13 provides a DC bias path for D2, and R19 and D4 are used to limit the current through the CRT.
Q7 Pes a6 A6) HORIZ PULSE Q8 ASE 9 3 ast HORIZ OSC 2 rey HORIZ ORIVER eu ah || Se oo P35 2) base 25K R330 (| 200 a) cz : ca R36 1.5K om} lL Sa" yg = 371023 SHAPER HORIZ DRIVER
TO 4.3K yaw Game
Figure 6-6 Motorola Monitor Horizontal Deflection Circuit
Capacitor C10 AC-couples the video from the collector of Q5 to the cathode of the CRT if D4 turns off due to high beam currents. Resistor R17 is the collector load for Q5, and R15 provides the bias current for the zener diode D3. Capacitors C9 and C6 filter video frequencies from the +150 volt and +12 volt supplies. Resistor R14 and zener diode D1 are used to supply +12 volts for Q1, Q2, and Q3.
D. HORIZONTAL DEFLECTION CIRCUITS (See Figure 6-6) Phase Detector (See Figure 6-7) The phase detector consists of two diodes (D5 and D6) in a keyed clamp circuit. Two inputs are required to generate the required output, one from the horizontal sync amplifier, Q11, and one from the horizontal output circuit, Q9. The required output must be of the proper polarity and amplitude to correct phase differences between the input horizontal sync pulses and the horizontal time base.
The horizontal output (Q9) collector pulse is integrated into a sawtooth by R24 and C12. During horizontal sync time, diodes D5 and Dé conduct, which shorts C12 to ground. This effectively clamps the sawtooth on C12 to ground at sync time. If the horizontal time base is in phase with the sync (waveform A), the sync pulse will occur when the sawtooth is passing through its AC axis, and the net charge on C12 will be zero (waveform B). If the horizontal time base is lagging the sync, the sawtooth on C12 will be clamped to ground at a point negative from the AC axis. This will result in a positive DC charge on C12 (waveform C). The positive polarity causes the horizontal oscillator to speed up and correct the phase lag. Likewise, if the horizontal time base is leading the sync, the sawtooth on C12 will be clamped at a point positive from its AC axis. This results in a net negative charge on C12 which is the required polarity to slow the horizontal oscillator (waveform D).
Components R23, C15, R25 and C17 comprise the phase detector filter. The bandpass of this filter is chosen to provide correction of horizontal oscillator phase without ringing or hunting. Capacitor C13 times the phase detector for correct centering of the picture on the raster.
Horizontal Oscillator The horizontal oscillator employs the principles of the Hartley-type oscillator. Its operating frequency is sensitive to its DC base input voltage, thus permitting the frequency of the oscillator to be varied by the output voltage of the phase detector. The main frequency-determining components are L1, C19, and R28. The oscillator operates as a switch being biased alternately into saturation and cut-off. The initial forward starting bias is supplied via R26.
Horizontal Pulse Shaper and Driver The horizontal pulse shaper Q7 serves asa buffer stage between the horizontal oscillator and driver. Capacitor C20 and resistor R30 combine to shape the input waveform to the required duty cycle of 50%, which is necessary to drive the horizontal output stage.
REFERENCE HORIZ. SYNC
OSC,ON FREQ NO CORRECTION VOLTAGE DEVELOPED
OSC,SLOWS, POS. CORRECTION VOLTAGE
OSC, FAST, NEG. CORRECTION VOLTAGE
Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms
The horizontal driver Q8 operates as a switch to driving horizontal output transistor Q9 through T1. Because of the low impedance drive and fast switching times, very little power is dissipated in Q8.
Resistor R35 and capacitor C21 provide damping to suppress ringing in the primary of T1 when Q8 goes into cut-off. Resistor R36 is used for limiting current in the collector of Q8, and C22 filters the horizontal frequency variations from the DC side of the transformer primary. Horizontal Output (See Figure 6-8)
The secondary of T1 provides the required low drive impedance for Q9. Resistor R37 limits current in the base of Q9, while capacitor C23 provides additional reverse bias to keep Q9 turned off during the horizontal retrace pulse. Transistor Q9 operates as a switch which once each horizontal time period connects the supply voltage across the parallel combination of the horizontal deflection yoke and the primary of 12. The required sawtooth deflection current through the horizontal yoke is formed by the L-R time constant of the yoke and output transformer primary. The horizontal retrace pulse charges C27 through D8 to provide operating voltage for G2 of the CRT. Momentary transients at the collector of Q9, should they occur, are limited to the voltage on C27, since D8 will conduct if the collector voltage exceeds this value.
The damper diode D7 conducts during the period between retrace and turn-on of Q9 to reduce retrace overshoot; capacitor C28 is the retrace tuning capacitor. Capacitor C25 blocks DC trom deflection yoke. Components R38 and C26 are damping components for the width and linearity coils. Capacitor 32D is charged through D10, developing the video output supply voltage
ua HORIZ UN OOO Lan \, HoRiZ HORIZ YOKE WIOTH
| a3 | O26 | ay | a | oe |
c2s¢—W 1 n ay, ene SER sabe =
| to | HoR'Z OUTPUT | opel | ye | . | a |
| 9g —a—MORI2 DRIVER | oly | 90 NOT MEASURE were METER | fe toPwe | ||
| COLLECTOR | o | +e | oe |
1D aS HEATER AMPER |. VOLTAGE anne 254) OAT FOR VI
Ral 0.0 TO PIN 1 47m roe
| the = | soe | ae | |
| t | 20d | 12 | |
| \e42 Focus | eo | Ro | |
| Dwtew | 0320 | TRANS, | h |
| es | ° | 20 | crt |
| ™ | ' | = | 2nd ANODE |
R43 . bi
| Tock | aye | geo | ow | y |
| SE | 5K | to | ||
| ww ont | [or | ICA |
MEADS! |AED Resicde at
Figure 6-8 Motorola Monitor Horizontal Output Circuit
T0.Q1 EMITTER +1
RSS: esl 10K: Se Qi3 st Abs VERT. SYNC. AMPL.
Figure 6-9 Motorola Monitor Sync Circuit Syne Circuits (See Figure 6-9)
The video signal is coupled from the emitter of Q1 to the base of Q10 through C33. The negativegoing sync tips turn on Q10 and are clamped to the value of the base voltage due to the base-emitter diode junction. The video information within the composite video signal, however, is less negative and Q10 remains off between each sync tip. Therefore, the waveform at the collector of Q10 will contain only the composite sync pulse information.
Resistors R45 and R46 provide base bias for Q11. The composite sync pulses are amplified and inverted by Q11 where they are coupled to the vertical sync integrator Q12, the horizontal phase detector, and the video clamp diode D2. Resistors R47, R48, and R49, are the collector load for Q11, and also provide base bias for Q12. Resistor R50 limits current through the base-emitter junction of Q12, and R51is its collector load. Components R52, C34, R53, C35, and R54 form a double integrator which removes the horizontal pulses from the composite sync signal, leaving the vertical pulses to be amplified by Q13 and coupled to the vertical oscillator.
Vertical Oscillator and Output (See Figure 6-10) The vertical oscillator is a relaxation oscillator and operates at a free-running frequency that is set by
+12V +73
VERT, 013 osc, AOS Ls | VERT. CHOKE,
Ql4 MPS-AL3
- Ree c40 VERT. . DRIVER 4b eat oF oo TO R68. 100} 1 qis 82V = VERT. OUTPUT Lap VERT. YOKE R67
Yel Wye
Figure 6-10 Motorola Monitor Vertical Oscillator Circuit
the value of resistors R56 and R57. The series combination of C37 and C38 charges through D14, R61, and R60, until D12 turns on. This occurs when the anode voltage of D12 exceeds the gate voltage by approximately 1.0 volt. When D12 conducts, C37 and C38 are discharged to nearly zero volts; then D12 turns off and the cycle repeats. The value of R61 and the setting of R60 determines the amplitude of the waveform.
Diode D14 provides a small incremental voltage above ground to overcome the forward base-emitter drop of Q14; D13 provides temperature compensation for the output stage. Resistor R96 provides a constant oscillator load for variations in input impedance of Q14. Transistor Q14 is an emitter-follower used to transform the high impedance drive sawtooth to a low impedance drive for Qi5.
The vertical choke L5 acts as a current source during linear scan time and provides a high-voltage pulse to aid retrace when Q15 shuts off. To limit this pulse to a safe value, a varistor, R66, is connected across the choke.
Since the impedance of the choke decreases when the collector current of Q15 increases, severe vertical non-linearity will result unless some compensation is employed.
Resistors R64 and R62 couple the emitter voltage of Q15 to the junction of C37 and C38. This path is resistive, and the waveform coupled back will be integrated by C38. This results in a pre-distortion of the drive sawtooth. This is done to compensate for the non-linear charging of C37, C38 and the changing impedance of C5. An additional feedback path through R63 and C39 serves to optimize the drive waveshape for best linearity. Capacitor C40 couples the signal to the vertical yoke winding and blocks DC.
Spot Kill (See Figure 6-11) The spot kill circuitry is used to reduce the effect of the electron beam concentrating on one area of the CRT after the monitor is turned off. The circuitry is accomplished by raising the arm of potentiometer R73 to the +150 volt level and, therefore, increasing the brightness to maximum to dissipate the highvoltage charge that normally remains in the CRT.
When the monitor is operating, transistor Q20 is on and its collector is near zero volts. Capacitor C44 charges through the base-emitter junction of Q20 and R97. Resistor R72 provides the base bias voltage required to keep Q200n. When the monitor is turned R73 BRIGHTNESS R97: R72 1K 47K:
TORT7 CRT, PIN2
Figure 6-11 Motorola Monitor Spot Killer Circuit
off, the falling +73 volts is coupled to the base of Q20 to turn off the transistor causing its collector voltage to rise to approximately +150 volts. Diode D24 prevents the negative voltage swing at the base of Q20 from exceeding the reverse voltage rating of the transistor.
Blanking Amplifier (see Figure 6-12) The blanking amplifier combines both the vertical and horizontal retrace pulses to turn off the electron beam in the CRT once every horizontal line and once every vertical field. Capacitor C41 couples the vertical retrace pulses and capacitor C31 couples the horizontal retrace pulses to the blanking amplifier. Resistor R68 determines the amplitude of the vertical pulses, while R69 determines the amplitude of the horizontal pulses. Capacitor C42 bypasses R69 to couple the leading and trailing edges of the horizontal retrace pulses to the amplifier. Resistor R70 allows C41 to discharge when the retrace pulses swing below zero voits. Diode D15 prevents the retrace overshoot from exceeding the reverse voltage rating of Q20. Resistor R71 permits Q20 to turn off between retrace pulses, while R75 and R76 provide the collector voltage for Q20. Capacitor C43 couples the blanking pulses to the control grid of the CRT.
rem)
Figure 6-12 Motorola Monitor Blanking Amplifier Circuit
RE (CONTRAST) (HORIZ. OSC.) R73 Te Rae (RIGHT) (Focus) 12
Figure 6-13 Motorola Monitor Chassis Rear View —Component Location
Figure 6-14 Motorola Monitor Circuit Board Detail—Solder View
Figure 6-15 Motorola Monitor Schematic Diagram
R64 R60 VERT. VERT. Di2 13 LIN. | size p23 018 11
D20 | O19 \Ra4 P3 +73 ony a4 Sh
msi28298 9 1a gitsay D5/D6 (NOT
SHOWN)
a6 Ti a7 A73
BRIGHT FOCUS 12
pa (NOT 1 gt PS CONTRAST
Figure 6-16 Motorola Monitor Circuit Board Detail—Component Location
Table 6-2 Motorola Replacement Part Numbers,
L Poly. D23,D24 48S191A05 REF. PART No. | NUMBER DESCRIPTION NO. NUMBER | DESCRIPTION
| Capacitors: | C31 | 8S510191B98 | -01, 10%, 250V; Poly. | ||
| All values are in Microfarads unless otherwise noted. | 32 | 23$10255B73 | 20/200, 400/125, 600/100, | ||
| c1 | 23S10255A27 | 47, SOV; Lytic | 200/50; Lytic | ||
| C2 | 218135660 | .05, +80-20, Z5V, 50V; | C33 | 8S10191A51 | -033, 10%, 160V; Poly. |
| Cer. Disc. | 34,C35 | 8S10191A32_—.047, 10%, 250V; Poly. | |||
| C3, C4 | 235187A26 | 22, 25V; Lytic | C36 | 21$180E60 | .01, +80-20, Z5V, 50V; |
| cS | 21$180E60 | .01, +80-20; Z5V, 50V; | Cer. Disc. | ||
| Cer. Disc. | C37, 38,39 8510191B67 | —0.22, 10%, 250V; Poly. | |||
| C6 | 218135660 | -05, +80-20, Z5V, 50V; | C40 | 23S10255A60 | 100, 63V; Lytic |
| Cer. Disc. | ca | 8S10212B16 | 0.1, 20%, 400V; Mtlz. | ||
| C7 | 218131625 | 330pf, 10%, X5F, 500V; | Poly. | ||
| Cer. Disc. | C42 | 218180C82 | 0.33, 10%, N150, 500V; | ||
| C8 | 21$180B87 | 220pf, 10%, X5F, 500V; | Cer. Disc. | ||
| Cer. Disc. | C43 | 8S10191B67 | (0.22, 10%, 250V; Poly. | ||
| ca | 8S10191B99 | .015, 10%, 250V; Poly. | C44 | 23$10255B28 | 4.7, 100V; Lytic |
| C10 | 8510212B18 | 0.22, 10%, 400V; | C45 | 8510191B90 | —-.033, 10%, 250V; Poly. |
| Mtlz. Poly. | C46 | 218132492 | .01, +80-20, Z5V, 100V; | ||
| cu | 218131625 | 330pf, 10%, X5F, 500V; | Cer. Disc. | ||
| Cer. Disc. | ca7 | 23810255B63 | 100, 10V; Lytic | ||
| C12 | 21$180C41 | .0027, 10%, Z5F, 500V; | C48 | 21S180D56 | 47pf, 10%, N750, 100V; |
Cer. Disc. Cer. Disc.
| C13 | 21$180C02 | 10pf, 10%, N150, 500V; | c49 | 21$180B51 | .001, 10%, XSF, 500V; |
Cer. Disc. Cer. Disc.
| C14 | 21$180D34 | .005, 20%, Z5F, 1KV; |
Cer. Disc. Diodes:
| c15 | 23510229A32 | 1.0, 16V; Lytic | D1 | 48S10813A03 | Diode, Silicon, Zener; |
| C17 | 8510191B90 | .033, 10%, 250V; Poly. | IN5242 | ||
| C18 | 8510299B28 | —.01, 10%, 100V; Polycarb. | D2 | 48D67120A13_— | Diode; A13 | |
| c19 | 8S10299B29 | .0082, 10%, 100V; | D3 | 48S10813A01 | Diode, Silicon, Zener; |
Polycarb. 1N5234B
| C20 | 8S10191B98 | .01, 10%, 250V; Poly. | D4 | 485191A02 | Rectifier, Silicon; 91A02 |
| C21 | 21S180B51 | .001, 10%, X5F, 500V; | D5,D6 | = 48D67120A11_—— | Diode; A11 |
| Cer. Disc. | D7 | 488134921 | Diode, Damper; D1D | ||
| C22 | 8510191B98 | .01, 10%, 250V; Poly. | D8 | 488134978 | Diode, Pulse Lim; D1K |
| 023 | 23510255B50 | 150, 10V; Lytic | D10 | 48S191A05 | Rectifier, Silicon; 91A05 |
| C24 | 21S180B51 | .001, 10%, X5F, 500V; | p11 | 485137114 | Rectifier, H.V., D2Y |
| Cer. Disc. | D12 | 485137638 | Vert. Osc.; MPU6027 | ||
| C25 | 8S10299B27 | 0.82, 10%, 200V; Mtlz. | D13,D14 | 488191A05 | Rectifier, Silicon; 91A05 |
| Polycarb. | D15 | 48D67120A11_ | Diode; A11 | ||
| ed | Piststeas | 2p Dezel als | Die. Dia’ | 488191405 | Rectifier, Silicon; 91405 |
| C27 | 8510212A11 | 1.0, 10%, 630V; Mtlz. | D20 | 48S10813A02 | Diode, Silicon, Zener; |
Poly. 1N5231B
| C28 | 8S10571A06 | .01, 5%, 1200V; | D21 | 48S10813A03 | Diode, Silicon, Zener; |
Polyprop. Foil 1N5242
| 29 | 8S10212B53 | (0.47, 10%, 630V; Mtlz. | D22 | 48D67120A11 | Diode; A11 |
Rectifier, Silicon; 91A05
Table 6-2 Motorola Replacement Part Numbers
| ici | Part No. | | | Description | Ne | Part No. | Description |
| Fuses: | R60 | 18D25245A29_—- | Vert. Size; 250K | |||
| FA, F2. | 658138269 | Fuse, 0.8A-250V | R64 | 18D25245A31 | ‘Vert. Lin.; 100K | |
| R66 | 6$10201A04 | Varistor, 1 ma, 120V, 0.5' | ||||
| Integrated Circuits: | R73 | 18D25245A28 | Control, Brightness; 200K | |||
| Ic1 | 51$10732A01 | Ref. Ampl.; T3F | Rad | 178135589 | 150, 10%, 10W | |
| R93 | 18D25245A21 | Control, +73V out Adj.; |
Coils/Chokes: 2.5K
| u | 24C25448A01 | Coil, Horiz. Osc. | R95 | 10731A03 | 1.5K, 10%, SW |
12 24D25603A09 = Coil, Horiz. Width
| B3 | 24D25248A14 ~— Coil, Horiz. Lin. | Switches: | |||
| a | 24D25261A09 | Coil, Defl. (M5000-155, | swt | 40810624407 | Switch, Slide; D.P. D.T. |
M5010-155}
| 4 | 24D25261A10 | Coil, Defl. (7000-155, | Transfortnérs: | |
| M7010-155) | 1 | 25D25221A05 —- Horiz.Driver | ||
| b | 25D25221C12_ | Choke, Vertical | Tr | 24D25240B23—_-H.V. Transformer |
| T3 | 25D25239B20 | Transformer, Power |
Transistors: (M5010-155, M7010-155)
| Qi | 485137171 | Emitter Follower; A6H | TB | 25D25239B30 | Transformer, Power |
| Q2 | 488137172 | Video Pre-Ampl.; A6} | (M5000-155, M7000-155) | ||
| Q3 | 488137127 | Video Pre-Ampl.; P2S | |||
| Q4 | 485134952 | Video Driver; A2jJ | Misc. Electrical Parts: | ||
| Q5 | 485137476 | Video Output; BIE | M1 | 96S241A01 | 19"-CRT; Type 19VARP4 |
| Qe | 485137172 | Horiz. Osc.; A6} | (M5000/M5010) | ||
| Q7 | 485137127 | Horiz. Pulse Shaper; P2S | V1 | 96510848A01 | —-23"-CRT; Type |
| Q8 | 485137093 | Horiz. Driver; ASF | M22VATP4 (M7000/ | ||
| Qa | 485137570 | Horiz, Output; B2L | M7010) | ||
| Q10 | 488137173 | Sync Separator; P2W | |||
| Qu | 48S 137172 | Sync Ampl.; A6} | Mechanical Parts: | ||
| Qi2 | 488137172 | Vert. Sync Integrator; A6) | 9B25456A01 | Block, Fuse (F1,2) | |
| Q13 | 485137172 | Vert. Sync Ampl.; A6} | 42D25158C01 | Clamp, Defl. Coil | |
| Qu | 485137639 | Vert. Driver; MPS A13 | 26510251408 | Heat Sink (Q5) | |
| Q15 | 488137596 | Vert. Output; B2V | PI | 15S10183A69 — Housing, Connector; | |
| Q16 | 488137172 | Blanking Ampl.; A6J | Female (12-Contact, | ||
| Qi7 | 485137368 | Regulator; ASW | Less Contacts) | ||
| Qi | 485134952 | Reg, Driver; A2j | 39$10184A67 | Contact, Plug; 5 Req’d | |
| Qi9 | 485137476 | Reg. Buffer; BIE | MS000/M7000, 9 Reqd; | ||
| Q20 | 488137476 | Spot Kill; BIE | MS5010/M7010 | ||
| P2 | 15$10183A82 | Housing, Connector; |
Resistors Controls: Male (3-Contact, Less
| the description when ordering standard values of | P2 | 15810183481 | Housing, Connector; |
fixed resistors up to 2 watts. Female (3-Contact, Less
| R6 | 18D25245A27 | Control, Contrast; 500 | Contacts), M5010/M7010 | ||
| R14 | 178135204 | 100, 10%, SW | 39510184A67 | Contact, Plug; 3 Req'd | |
| R17 | 17810731A01 | 3.9K, 5%, SW | for P2 | ||
| R36 | 17S10130B07. | 1.5K, 10%, 3W | P3 | 28S10586A35 | Header, Connector; |
| R42 | 18D25218A14_ —- Control, Focus; 2M | 2-Contact |
Table 6-2 Motorola Replacement Part Numbers
PART PART
NUMBER DESCRIPTION NUMBER DESCRIPTION
| 15S$10183B12 | Housing, Connector; | 14B25459A01 | Insulator, Fuse Cover |
Female (3-Contact, Less (F1, 2)
| Contacts) M5010/ | 14A562353 | Insulator, Mica (Q9, |
M7010 Q15, Q17)
| 39S10184A84 = Contact, Plug; 3 ea. | 14C25230A01__— | Insulator, Molded (On |
Req'd for P5, M5010/ D11 Body)
| M7010 | 14S10157A30 | Insulator, Nylon (2- |
| 15510183A81 | Housing, Connector; | Req’d.); Mtg. P.C. Board |
Female (3-Contact, Less 14$10550A02 _—Insulator, Transistor Contacts), M5006/M7000 Cover (Q9, Q15, Q17)
| 15$10183A82 | Housing, Connector; | 38136050 | Screw, Tpg; 6-20x¥ CLU |
Male (3-Contact, Less Pan (Mtg. Q9, Q15, QI7 Contacts), M5010/M7010 and D11 Socket)
| 39S10184A64 | Contact, Receptacle; | 9D25470A01 | Socket, CRT; Incl’s. |
3 Req'd. for $2 R77, R78, R79, R80
| 15S10183A94_ | Housing, Connector; | 9D25201A01 | Socket, H.V. and CRT |
Female (2-Contact, Less Anode
Contacts) 9C63825A03 Socket, Power Transistor
| 39510184472 | Contact, Receptacle; | Q9, Q15, Q17) |
3 Req'd. for $3 41D65987A01 = Spring Special; CRT Aquadag Gnd.
A. GENERAL
TM-600 and TM-623 is a television monitor for video games. It is designed for operation either from a power supply of 115 volts/50-60 Hz AC or 230 volts/ 50-60 Hz AC. The complete monitor incorporates a picture tube, an integrated circuit, 20 silicon transistors, 18 silicon diodes, 2 germanium diodes, anda high-voltage selenium diode.
This model is equipped with 5V/3A power supply for the operation of the TTL control board and operation double-pulse-type AFC circuit to obtain a stable picture.
B. SPECIFICATIONS Power Supply Input 115 volts/230 volts 50-60 Hz +10%
Power Consumption 60 watts
Video input 0.5 volts composite P/P for 100 volts 2.5 volts P/P maximum Sync negative at input TEC VIDEOELECTRONICS INC. SERVICE MANUAL
Picture Tube 19" (500 mm), 114° deflection for Model TM-600 23" (584.2 mm), 114° deflection for Model TM-623 Integral implosion protection
High Voltage 18 KV nominal at 0 microamperes beam current
Horizontal Retrace Time 12 microseconds maximum
Resolution 500 lines minimum at picture center
Scaning Frequency Horizontal:15.750 Hz +500 Hz Vertical: 50-60 Hz
Tone Burst Amplifier 5 watts peak output with TTL drive at nominal line, fully adjustable. 4 watts peak output at low line.
Environment Operation: Maximum ambient temperature 50°C (122°F) Storage: Temperature range from —40°C to +65°C
Model TM-600 and TM-623 Monitors
TEC Videoelectronics Inc. (TVI) 3010 Scott Boulevard Santa Clara, CA 95050 101
DEFLECTION CENTERING
YOKE cone HORIZ. LIN,
HV Rect
HY TRANS,
Pi AMP. 0.5 AMP. ‘CONNECTOR
Figure 6-17 TEC Monitor Chassis, Rear View
SVinecutaton Eotoensen 90; B+ REGULATOR
r
" e
4304 VERT. OUT TRANSISTOR
2305 VERT. OUT TRANSISTOR
VERT LIN.
POWER TRANS, VERT, HEIGHT
RESISTOR RIGHT
Figure 6-18 TEC Monitor Chassis, Top View
HORIZ. DRIVER TRANS.
Honiz. osc, HoRiz. OUTPUT com
vioeo ourPur
HV RECT
HV TRANS
veR: BALANCE WIDTH co
CONTRAST BRIGHT
VERT. VERT HOLD HEIGHT] a TO DEFLECTION YOKE
Figure 6-19 TEC Monitor Printed Circuit Board, Top View
Table 6-3 TEC Monitor Replacement Parts Numbers
bce] Ref.
| Ref. | PartNo. | Description | No, | PartNo. | Description |
| Electrical Parts: | Q303 | 5300500201 | MPS9700U__ | Vert Amp | |
| PCB1 | 2215303600 | Main PCB | or MPS834 | ||
| A801 | 485TM60003 | «CRT PCB | Q304 | 4310400030 =. 2SC1106_~—“Veert Output |
305 or 2N6307
| Transistor and IC: | Q400 | 5310500202 | MPS9700T | Phase Inv |
| Q200 | 5310500202 | MPS9700T | 1st Video Amp | or MPS834 |
| or MPS834 | Q401 | 5310500202 | MPS9700T | ~—Horiz Osc |
| Q201 | 5310500261 | MPS9750T | 2nd Video Amp | or MPS834 |
| or MPS4356 | Q402 | 5310500410 | 2N6558 | Horiz Amp |
| 202 | 5310500410 | 2N6558_~— | Video Output | or MJE9742 |
or MPSU-10 or 2N4354
| Q301 | 5310500261 | MPS9750T | Sync Separator | Q403 | 5310400040 =. 2SC1875.—Horiz Output |
or MPS4356 or MJ205
| Q302 | 5310500201 | MPS9700U | Vert Osc | %Q901 | 5310400030 =» 2SC1106 | Power Regulator |
or MPS834 or MJ3430
Table 6-3 TEC Monitor Replacement Parts Numbers
Ref. a Re
No. Part No. Description iy Part No. Description
| Q902 5310500410 | -2N6558._——SsRegulator Amp | , | ||||
| ‘or £310800070 | —s MPS-UD4 | T401 | 589514015, | TLN-S06BX Horiz Osc | ||
| 903 5310500280 | LM1796.—_—Reference Amp | T402 | 589518012 | TLN-519— | Horiz Drive | |
| or MPS-D01 | * 7403589517017 | TFB-1006AS_F.B.T | ||||
| Q904 5310500450 | MJ2955 | 5V Regulator | * 7901 | 589519021 | TPW-600 | Power Trans |
CRT and Diode: Resistors
| * v801 | 5380000060 | 500SB4 | CRT | R201 | RD-4L471) | 470 ohm) %& W |
| D203 5340200280 | MR9712._ | Silicon Diode | R202 | RD-4L223) | 22 K ohm J %& W | |
| or IN4004 | L. V. Rectifier | R203 | RD-4L563] | 56 K ohm J % W | ||
| Dz04 5340200430 = IN4748 | Silicon Diode | R204 | RD-4L471) | 470 ohm) % W | ||
| or IN4002 | Blanking Clip | R205 | RD-4L332J | 3.3 Kohm J % W | ||
| D205 5340200430 | «=——IN4148 | Silicon Diode | R206 | RD-21823 | 8 KohmJ %W | |
| or IN4002 | Blanking Clip | R007 | RD-AL | 56 | ||
| D206 5340200430 | ——IN4148 | Silicon Diode | 7 | 60) | ene | |
| or IN4002 | Blanking Clip | R208 | RD-4L.102) | 1Kohm J % W | ||
| D207 534020280 | MR9712 | 200V Rect | R210 | RS-029562) | 5.6 K ohm J 2W | |
| ‘or IN4004 | R215 | RD-42101) | 1K ohm J % W | |||
| D301 | 5340200260 = MR-9701 | _—Rectifier Silicon | * R216 | RD-4L101) | 100 ohmJ % W | |
| Diode | * R217 | RD-41470) | 47 ohm) %W | |||
| D401 5340100046 | AA143 | Phase Det | R278 | RD-4L223) | 22 Kohm J % W | |
| D402 5340100040 = A143. | Phase Det | R219 | RD-41563) | 56K ohm | 4 W | ||
| a 5340200300 | MR9722.-—s | Damper | R220 | RD-4L102) | 1Kohm | %W | |
| D404 5340400120 | TV20-2K80J_H.V. Rectifier | R221 | RD-ALI02) | TKohm) | “Ww | |
| or HS30/Ib | a? | RD. | 1 | nw | ||
| D801 | 5340200290 = MR9713._«—«400V Rectifier | ibe | ' x om ) : w | |||
| D901 | 5340200270 | MR9704.—éRectifier | Rea RD 2102) | anh | ||
| ‘or IN4005 | Silicon Diode | R224 | RD-2L122) | 1.2K ohm J %W | ||
| D902 5340200270 | MR9704 | Rectifier | * R226 | RSOIPION | 100 ohm) 1W | |
| or IN4005 | Silicon Diode | R227 | RD-21123) | 12K ohm) % W | ||
| D903 5340200270 | = MR9704_—séRectifier | R228 | RD-2L105) | 1.5K ohm J 2 W | ||
| or IN4005 | Silicon Diode | Rm9 | RD-4Mé681) | 680 ohm) % W |
D904 5340200270 =» MR9704_—sRectifier
| or IN4005 | Silicon Diode | ae | soatstay | ook orm Juw |
50 y
| D906 5340300220 | INS858A_— | Zener Diode | 8 | : | >e Kionm | 1% W |
| ‘or 5340300310 | IN6002A | R304 | RD-4M102) | 1K ohm) %W | ||
| D907. | R308 | RD-4M104} | 100 K ohm J 1% W | |||
| ba 5340200690 | MDA970-1_ | Rectifier | R309 | RD-AMISST | 1.5MohmJ % W | |
| 0910 | R310 | RD-4M332). | 3.3 Kohm J % W | |||
| R311 | RD-4M563) | 56 K ohm J % W |
Coils and Trans: ,
| *L401 | 589515015 | TDY1005 | —_-D.Y. Coit | R312 | ROL 82) | 1.8K ohm J % W |
| L402 | 589512015 | HCH1005 | Horiz Choke | R313 | RD-4L153} | 15 Kohm J %4 W |
| Coil | R314 | RD-4L183) | 18K ohm J % W | |||
| L403 | 589572012 | HC2-035 | Choke Coil | R315 | RD-4L.203) | 20 K ohm | % W |
| L404 | 589512012 | HC2-035 | Choke Coil | R316 | RS-2P333) | 33 K ohm j % W |
| L405 | 589514013 | AZ-9177DM. Width Coil | R327 | RD-4L104) | 100 Kohm J % W | |
| 1406 | 589514016 | LH-15)54 | Lin Coil | R320 | RD-4L124) | 120 Kohm J %4 W |
Table 6-3 TEC Monitor Replacement Parts Numbers
Ref. N
R323
R324
R326
R339
R331
R332
R333
R334
R336
R337
R338
R339
R340
R401
R402
R403
R404
R405
R406
R407
R408
R419
R410
R411
R412
R413.
R414
R415,
R416
R417
R418
*R420
*R421
R422
R425
R426
R802
R804
R811
*R901
R902
R903 Part No.
RD-4L433)
RD-4L471)
RD-4L152)
RD-4L101) RD-4M331}
RD-4L102) RS01P682) RD-21183)
RD-41221)
5160122901
RS-2P 150)
5160112901
RS01P220T
RD-4L153)
RD-4L821)
RD-4M561)
RD-4M103} RD-4M103) RD-41272)
RD-4L681)
RS02P682)
RD-41270)
RD-4L182)
RD-4L151J
RD-4L561)
RSO1P682) RD-21221)
5160122903
RD-21569)
RS02P182)
RSO1P123)
RX05P220)
RD-21569)
RD-4L153)
RD-4L153)
55337153
RD-2L154) RD-2L474)
RD-2L561)
RX20P251}
RD-2L101)
RD-2L123} Description
43 K ohm J
470 ohm) 1.5 K ohm J 100 ohm) 330 ohm J 1K ohm)
6.8 K ohm J 18 K ohm J 220 ohm)
2.2 ohm) 15 ohm J 1.2. ohmJ 22.) ohm J 15 K ohm J 820 ohm) 560 ohm)
10 K ohm J
10 K ohm }
2.7 Kohm J
680 ohm) 4.7 K ohm J
27 ohm}
1.8K ohm J
150 ohmJ 560 ohm) 6.8 K ohm |
220 ohmJ
2.2 ohm) 5.6 ohm) 1.8 K ohm J 12 K ohm J 22.) ohm J 5.6 ohm J 47 ohm J 15 K ohm J 15 K ohm J 150 K ohm J 470 K ohm J
2MQJ
250 ohm) 1K ohm J
12 K ohm J % W Ye W ve W YW
= stteeeeeee Me Ye W 1W
”% W
1W
% W
2Ww
1W
5 W
*%W
1W ve W Ye W Ya W ve W % W 20 W WW ve W Ref. No. Part No.
RD-2L123]
R905 RD-2L.223)
R906 RD-2L563)
R907 RD-21.563)
R909 RD-21682)
Controls: R211 553102005E
R319 553104005B
R321 553124008B
R327 553472008B
R335 553102007B
R427 5533030058
R803 553254005B
R805 5532050058 R908 = 553472007B
Capacitors: 201 CE2G1C470
202 CE2G1F101
C203 CE2G1C220
204 CE2G1H101
205 CE2G1C220
206 C1SL1H561K
207 CE2G0)221 208 5270322401
€209 CE2G2F229
210 CE2G1H220
C211 CE2G1H339
C213 CKIF2H102K
220 CE2G2F220
301 CQIM1H473K 304. CK1B1H391K
305 CE2G1H478
306 56405333
307 CQ1M1H562K 308 = CQIM1H273K C309 CQIM1H123K 311 CQIM1H124K C312 CQIM1H392K C313 DS5D1C229M
C314. CQIM1H474J C315 CQIM1H333K
C316 CF2G1A470 Description
R322 RD-41224) 220 KohmJ % W R904 12K ohm) %#W 22 K ohm) % W 56 K ohm) 56 K ohm J
6.8 K ohm J
1K ohm
100 K ohm
220 K ohm 4.7 K ohm 1K ohm
30 K ohm
250 K ohm
2Mohm
4.7 K ohm
47 mF
100 mF
22 mF
100 mF
22 mF
560 pF K 220 mF
0.22 mF M
2.2 mF
22 mF
3.3 mF
0.001 mF
2.2 mF
0.047 mF K
470 pF K 0.47 mE
0.033 mF K
0.0056 mF K
0.027 mF K
0.012 mF K
0.12 mF K
0.0039 mF K
2.2 mF
0.47 mF
0.033 mF K
47 mE a W a W hh W
Contrast
Vert. Hold
Vert. Height Vert. Linearity Vert. Balance
Horiz Hold
Bright Focus
B+ADJ
16V
25V
16V
35V
16V
50V
6.3V
400V
315V
35V
50V
500V
250V
50V
50V
50V
50V
50V
50V
50V
50V
50V
16V
50V
50V
10V
Table 6-3 TEC Monitor Replacement Parts Numbers
Ret, Part No. Description Ref. Part No. Descripti
No. . No. : ption
| 317 | CE2G2A101 | 100 mF | 100V | Fuses: | ||
| C318 | CKIEZH103K | 0.01 mF_—-500V | F902 | 6990620011 | 250V 2 Amp. | |
| 319 | 5270310307 | 0.01 mF = 630V | *F903 | 5990610013 | 250V 0.5 Amp. | |
| C401 | CQIM1H103K | 0,01 mF K | SOV | F904 | 5990630070 | 30V 5 Amp. |
| C402. | CQIMIH103K | 0.01 mF K | —50V | |||
| C403 | CQIM1H393K | 0.039 MF K_ 50V | gecgranical Paris: | |||
| C404 | CkiBDHIS1 | 4150 mae | S00v | KOI — 22-463020 | Mate-N-Lock Connector (AMP) |
60085005 Edge Collector (Molex)
| Cs | CReIH339 = a3mF | OV | S-A3915, | Transistor Socket (SMK) | ||
| C406 | CQIMIHI04K | 0.1 mEK | SOV | *TM60085001 | Fuse Holder | |
| C407 | CQIMiH223K | 0.022 mF_ J 50V | or *TM60085001 | Fuse Holder | ||
| C408 | CQIMIH683K | 0.968 mF} | 50. V | KO0S — 1-380826-0 | Stand-Off Fastener (AMP) | |
| C409 | CE2G1F470 | 47 mF | 25V | P401 | —-PE19-1569 | 4P Plug Assy. (Yoke Line) |
| C410 | CKIB2H681K | 680 pF KK | 500V. | P402—-PE19-1570 | 4F Recep Assy (Yoke Line) | |
| C417 | CK1B2H222K | 0.0022 mF K 500V | P403 | PE19-1571 | 3P Connector Assy. (Video | |
| 412, | CK1BIH752K | —-0.0015 mF K 50V. | Input) | |||
| C413. | CK1B7H102K | 0.001 mF K_ 50V | A621 | PE19-1572 | 4P Connector Assy. | |
| *C414CKiB3D471K | 470 pFK_—.2KV | (Q901 Line) | ||||
| C415. | CQIM2A104K | 0.1 mFK | 400V | A631 | PE19-1573 | 6P Connector Assy. |
| *C416 | 5270333201 | 0.0033 mF_—1.5KV | eer esel | |||
| C47 | CE2C2C100 | 40 mF | 160V | P406 = PE19-1574 | 2P Plug Assy. (Heater Line) | |
| cate | 5970333401 | 033 mFK | 200V | P407 — PE19-1575 | 2P Recep Assy. (Heater Line) |
TE901 PE19-1576 Terminator, 6 Pin
| CA19: | 56635101 | 100 mF | av | E001 | 135431015 | Ground Plate |
| 420 | 56625471 | 470 mF | 25V | Foo?, | 225164001 | Frame |
| 801 | 5270356302 | 0.056 mF K 630V | O03 | 5432001-1 | Plate Heat Sink A | |
| *C901 | 5240700400 | 450 mF | 200V | Q403D 54320071 | Plate Heat Sink C | |
| c902 | 100 mF | 160 V | ||||
| 904 | F2G2C229 | 2.2 mF | 160V | |||
| C905 | CKIF2H102k | 0.001 mF | 500V. | |||
| 911 | 56625105 | 10000 mF | —-25V | |||
| C912 | 56616018 | 1mF | 16V |
- J—Indicates = 5% tolerance cal K—Indicates +10% tolerance
- M-Indicates +20% tolerance Switches:
| *SW-1— | PE73-1567 | 715V/230V Power Line |
Slide Switch
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Safety-Critical Components Components marked with an asterisk (*) on the parts list and with gray shading in the schematic have special characteristics important for safety. You may create shock, fire, or other hazards by using a replacement that does not have the same characteristics as the recommended part.
901.0904 Mns7os S38 00m
a 19907 “D810 MOAa70.
_ THO rew.623 | TPW.600
TR, IC, and Connector Lines
MPs VIO _LMI796 MPS 9417 INSUSA MPS voa yp PS iweoo2 a "SRS. ¥O4 MPS 9750MPS 9700 ING:
104076 Q. i 208080 9. ece ece 2029.0} OPO} wieszo wikis Pi mc 7eosce = MES7A2
OF 6 ° oF
M2955 2scl io 2sc 1875 ‘or 2Ne558 0805 e600 zal, = a903 uM 1796 insasea oe
woRIZ HOLD
NOTES
- Unless otherwise specified, all resistance values 4. All waveforms are measured with strong signal are in ohms. input and contrast set to give normal picture.
- Unless otherwise specified, in the schematic dia- 5. This schematic diagram covers basic or repregram all capacitor values less than 1 are expressed sentative chassis only. There may be some differin mfd, and values more than 1 are in pfd. ences between actual components cn chassis and
- Voltage readings are taken with VTVM from point the schematic diagram. indicated on chassis to ground.
‘CONTRAST Mes 97507 Focus &
vert UN
Figure 6-20 TEC Monitor Schematic Diagram
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
an Ji_ ae : oo} | | ia i Ah « a oe LUT ee ; ra t : h AO ri 3020 : oe, cgot Tilt ae 901-904 ° e yo] Bt ans ie Ik R90!
woe t OF i = On
fs
Figure 6-21 TEC Monitor Wiring Diagram BOTTOM VIEW
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation Or improper testing.
In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may noi be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.