VS UniSystem Kit Manual
Vs. UniSystem Kit (Nintendo, 1985) · Kit Manual · 55 pages · 30 sections · original scan
VS. UniSystem€
KIT MANUAL
G
FOR INSTALLATION IN
©1985 Nintendo’of America Inc. *© 1982 King Feature Syndicate
Vil.
Vill.
Xi. TABLE OF CONTENTS
Introduction
Contents of VS. UniSystem™ kit
List of Tools Needed
Replacement Process Step-by-Step
Final Check Sheet and Adjustments
Wiring Diagram
Service Bulletins
CPU PC., Power Supply and Monitor Schematics
Reorder Parts List 5-18
INSERT
23-29
INSERT
30-41
- INTRODUCTION
VS. UniSystem™ kit
VS. UniSystem™ kit enables you to change Donkey Kong", Donkey Kong Jr.*, Mario Bros.*, Donkey Kong 3*, and Popeye** into a VS. UniSystem” in less than one hour. A VS. UniSystem* will use any non-interactive VS.-Pak*.
Before you begin, be sure you are properly prepared. Make certain you have selected the proper VS. UniSystem* kit for the particular game you are replacing. Next thoroughly read this instruction manual to familiarize yourself with the proper procedures. Make certain that you have all the tools necessary to complete the process.
If you have any questions, please call Nintendo Service at 1- (800)- 633-3236.
- Donkey Kong, Donkey Kong Jr., Mario Bros., Donkey Kong 3, and VS. UniSystem are trademarks of Nintendo of America Inc. ** A trademark of King Features Syndicate, Inc.
Il. Contents of VS. UniSystem kit
Parts Name Quantity Remarks
MDS-CPU PC. Board Assembly MGS-UP Operation Panel Assembly MGS-UP Front Screen (600W) Assembly MGS-UP Side Decal VS. UniSystem™ Manual 062 Shield Cover Complete Assembly 072-36P Edge Connector Harness 072-44P Edge Connector Harness Assembly MGS Serial Number Plate Flat Cable Tie Wood Screw 3.1 x 10 FCC Class-A Label FBI Sticker Following parts are for TKG, DJR, DKC, TMA only 054 Shield Cage Video Monitor Bracket (L) Video Monitor Bracket (R) Video Monitor Support Bar Blind Cardboard (large) Carriage Bolt 6 x 30 Cap Nut M6 Cap Nut M5 Machine Screw 5 x 12 Wood Screw 3.5 x 13 Ground Wire (E) Hole Template Following parts are for TPP only Power Supply and Transformer Assembly Fuse Set Bao paen nnn pani
AA ORRDHDANAAA without EPROMS and PPU with harness
821B-7B Power Assembly
Ill. List of Tools Needed
Flat (standard) screwdriver
Phillips screwdriver 7mm nut driver
8mm nut driver
10mm nut driver
Ws" or 6.5mm drill bit
Electric reversing drill
Phillips bit (for drill)
Staple gun Paper stapler
Lacquer thinner Denatured alcohol or other cleaner
Large wire cutter
IV. Step-by-step instructions
- Remove marquee/header (see illustration 1-1) A. Remove four (4) top trim screws B. Remove marquee plexiglass C. Replace marquee/header with new VS-Pak header D. Replace top trim and four (4) top trim screws
- Remove old control panel and front screen (see illustration 1-2) A. Undo control panel holddown clamps B. Disconnect harness and remove control panel C. Remove front screen by sliding back front screen clamp (access from back door)
- Remove instruction label (see illustration 1-3)
A. B. c. Spray label with lacquer thinner Wait 15 minutes and remove with putty knife Clean area with cloth and lacquer thinner
4, Remove monitor
moom> Unplug monitor connections and undo wire ties Remove blind cardboard on monitor only Remove monitor, upper monitor support bar and all carriage bolts (see illustration 1-4) Remove old side decal
- Side panels should have five (5) holes each. If your game has only two (2) holes, use template provided in kit and drill three (3) 1/4-inch or (3) 6.5-mm holes where indicated (see illustration 1-6).
- With old side decals removed, clean side panel with alcohol and install new VS. UniSystem decals. Decals are placed parallel to top and back of game 2” from edge. (See illustration 17) See decal application sheet on page 18
- Install side support bars on monitor (see illustration 1-8)
A. Install new horizontal monitor mounting brackets to side panel with flange toward front of cabinet and pointing up. Note: use carriage bolt as shown (see illustration 1-9 & 1-10) Install monitor in horizontal position Monitor is placed on top of side bracket supports .
- Install new blind cardboard (see illustration 1-11)
A. Remove adhesive backing on tape. Center blind cardboard on monitor and adhere. Place staple on top.
Top
- Remove old PC. Board set and mounting brackets and old wire harness (see illustration 1-13) . A. If P.C. Board’ wood shelf has slots made from square stock wood, remove these (see illustration 1-12) B. Remove old Main Wire Harness
- Remove old Shield cage assembly including Shield cover and old P.C. Board set
- Install new Shield cage so it is flush with rear of wood shelf and fasten with six (6) screws provided. IMPORTANT! On lower left corner install ground harness and connect the other end to the mounting bolt on the power supply as shown (see illustration 1-15 & 1-16)
These steps are for Popeye ONLY
- If you are replacing a Popeye game, remove old power supply transformer assembly (see illustration 2-1 & 2-2) Disconnect connector from switch plate Diconnect both plugs for monitor and lamp Disconnect ground harness connections Disconnect both power harness connections Remove four (4) wing nuts and take out old power supply Replace with new power supply assembly and tighten wing nuts
"1
These steps are for Popeye ONLY
- Change fuse to 5 AMP and change label to 5 AMP on switch plate (see illustration 2-3)
- Remove old P.C. Board assembly and old Main Wire Harness (see illustration 2-4) A. Remove the six (6) machine screws that hold on the Shield cover.
Remove Shield cover and complete P.C. Board assembly. Remove old Main Wiring Harness.
- Modify new Shield Cover Assy to fit old Shield Cage (see illustration 2-5)
A. Cut off six Fasteners on perimeter of Shield Cover Assy B. To install Shield Cover use six (6)machine screws from step 14A.
- Install new MDS PC. Board and shield cover assembly (see illustration 4-1)
A. Attach short harnesses to P.C. Board with 36 pin connector on top B. Slide P.C. Board into Shield cage grooves C. Do not fasten Shield cover until after final check sheet and adjustments Section V is completed
- Connection of Harnesses (see illustration 4-2)
A. Connect Coin, Service. Counter harnesses to 44P072 Edge harness.
Donkey Kong type connectors
Popeye type connectors
Donkey Kong Donkey Kong Jr. type connectors
44P072 Edge Connector Harness Assy
COIN (4 wires)
SERVICE (pin)
Popeye type connector COUNTER AUDIO (2pin) B pin) (4 pin) Donkey Kong 36P072 Edge Connector Harness Donkey Kong Jr. type connector
(12 pin)
To Control Panel
(15 pin)
- Install new front screen and fasten with front screen clamp (see illustration 4-4)
- Connect new VS. UniSystem control panel to harness and fasten down (see illustration 4-4)
- Screw on new serial number plate next to old plate.
- Attach FCC Class A label (see illustration 4-6)
A. Remove old FCC label B. Putonnew FCC label and staple all four corners
- Attach FBI sticker
A. Place label on back door just under lock (see illustration 4-7)
Side Decal Application
Step 1.
Start by peeling the protective backing “A” down about 6 inches from the top.
Place decal in desired position. Pull down slowly the remainder of the protective backing of “A.’”
While doing this, use a soft cloth to smooth decal onto side board, moving from top to bottom of decal.
Step 2.
Fold remaining decal back, exposing the unprinted side. Begin to peel protective backing “B”’” from center to right hand side “‘slowly.”’
Using soft cloth smooth decal onto side panel by running hand from top to bottom of decal, moving outward to the right hand side.
Front View
V. Final Check Sheet and Adjustments
- FBI sticker installed (MANDATORY)
- New serial number plate installed (MANDATORY)
- New FCC label installed (MANDATORY)
- Fuse label changed (Popeye only)
- P.C. Board adjustments made (see P.C. Board adjustments page 20)
- Monitor adjustments made (see monitor adjustments pages 21-22)
- Coins give credit
- Controls on operation panel functioning
- Sound checked
Adjustments
After powering up the game, you will probably find that the screen’s horizontal width is too narrow and the vertical height is too small. To make adjustment to the horizontal width, refer to the illustration on page 21. To adjust the vertical height, use the V-size adjustment on the rear of the monitor to make the picture larger (see page 22).
MDS P.C. Board
Component Side
Cautions: (1) Since the Dip Switch settings (SW2 only) may be changed by new game software, refer to the new game instructions in Operation Manual for VS. Pak.
- Do not touch the fixed variable resistors (VR1, VR2, VR3, VR4, VR5, and VR6), as they have already been preset and do not need adjustment.’
- If, however, color does not look correct, VR3, VR4, and VR6 may be adjusted.
Adjustment of Horizontal Width
Using a standard 2.6mm hex non-conductive core alignment driver, carefully turn L453 counterclockwise for a smaller horizontal screen size. L453 is located in the rear of the monitor just under the deflection yoke.
Alignment Tool
\ Heat Sink
UY Turn this way for
a smaller horizontal screen size
Adjustment of Video Monitor
To Game PCB _ Video Monitor 6P—600 Video < Main PCB
Harness RS Signal PCB
INVERT OUT NON INVERT OUT
This Signal PCB is only attached to TPPU-20-00 Video Monitor (32 Type) 20-EZV (R-C).
BRIGHT
SOUND VOLUME
& H HOLD Fuse 4A (Slow Blow) in
Video Monitor QO
Nv Main PCB
Fuse 0.3A (Midget Type)
Do not touch the inside of the Video Monitor. It contains many parts supplied with high voltage.
Nintendo
SERVICE DEPARTMENT
Dear Customers:
In addition to the steps you have already done, we felt it would benefit you if the previous cabinet and coin selector problems were checked to ensure the modifications had been done. Below is the list of service bulletins which deal with these problems.
We have included copies of these service bulletins:
TKG-08 Slam Switch 4-18-82
| DJR-01 | Upper Coin Door Hinge | 8-24-82 |
| DJR-02 | Model 730A Coin Selector | 1-04-83 |
| DJR-08 | Video Wrap Around | 9-09-83 |
Sincerely,
Nintendo of America, Inc.
1-800-633-3236 keV 1-206-882-2040
Nintendo
SERVICE DEPARTMENT BULLETIN # TKG.05
GAME: Donkey Kong, Donkey Kong Junior, Popeye, Mario Bros., Donkey Kong 3, VS System
SUBJECT: Slam Switch
In order to prevent the accumulation of free credits by kicking the coin door, a slam switch should be added.
In all cases the switch (a “normally open” weighted reed switch) should be mounted on the coin door. Connect one side of the slam switch to the brown wire on the coin switch (ground). The other side of the slam switch should be connected to a wire which will be run through the wiring harness to the CPU board. At this point the installations vary for the six (6) games.
Donkey Kong:
TKG2 and TKG3: Attach to Test Point 8, at board coordinates 3h.
TKG4: Attach to Test Point 2-RESET, at board coordinates 1L.
Donkey Kong Junior:
Attach to Test Point 2-RESET, at board coordinates 1L.
Popeye:
Attach to C13 (474 F electrolytic capacitor), +” side, at board coordinates 2N.
Mario Bros:
Attach to C38 (1004 F electrolytic capacitor), +" side, at board coordinates 4F.
Donkey Kong 3:
Attach to C25 (100 F electrolytic capacitor), ‘‘+" side, at board coordinates 2E.
VS. System
Attach to C3 (10y electrolytic cap) +” side, at board coordinates 1K.
1-800-633-3236 —o 1-206-882-2040
SERVICE DEPARTMENT BULLETIN # DJR-01
GAME: Donkey Kong Jr.
GAME: Donkey Kong Jr SUBJECT: Upper Coin Door Hinge
It has been brought to our attention that a flattened straw or similar object can be passed through the center opening in the upper hinge. If the object makes contact with the coin switch, it can be used to run up multiple credits.
The solution is to block the opening with a flange made of wood or metal. This flange should be mounted to the inside of the cabinet and can be obtained from us as a retrofit kit.
This problem is presented in all Radar Scope uprights, Donkey Kong uprights and early Donkey Kong Jr. uprights.
1-800-633-3236 GG. 1-206-882-2040
Detail Coin Mech. yy FeO HDLIMS ADAWSIS
Retrofit Flange
NOTE: Mount
new flange on
left coin mech
using existing
nuts and bolts so flange covers hinge when door is closed.
Nintendo
SERVICE DEPARTMENT BULLETIN # DJR-02
GAME: Donkey Kong Jr.
GAME: Donkey Kong Jr SUBJECT: Model #730A Coin Selector
It has come to our attention that there is a problem with the model #730A coin selector in that a nickel or a penny, if flipped through the entry just right, will continue through the mechanism and establish credits.
The solution to this problem is to add a small metal piece to the selector as shown in the enclosed drawing. This piece can be made from 18 gauge steel or even a paper clip as shown in the drawing. This piece is available at no charge. The threaded hole in the selector is an M83 x 6 MM size. If you cannot locate a screw this size, you can remove one of the machine screws from the power supply cage.
1-800-633-3236 ——————————— 1-206-882-2040
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Nintendo
SERVICE DEPARTMENT BULLETIN # DJR-05
GAME: Donkey Kong, Donkey Kong Junior
SUBJECT: Video Wrap Around on Left Side of Picture
We have recently received a number of service calls concerning the wrap around or fold over of the picture on the left hand side of the monitor. In most cases the problem may be solved by replacing capacitor C407 on the main monitor PC board. This is located just to the left of the high voltage cage when viewing from the rear of the monitor. The value of this capacitor is 10 microfarads at 160 volts (of course, any capacitor of 10 microfarads with a voltage rating higher will work also).
This capacitor is connected between ground and the B+ supply for the vertical output transistors, so if this capacitor becomes leaky it does not allow full vertical deflection of the screen; consequently, you get video information imposed over the other (wrap around).
If you have questions about this or any other questions concerning Nintendo products, please feel free to contact us.
IX. Reorder Parts List
Body Parts — Front View (Fig. 5-1)
ITEM
OMBNONAON= PART NO.
TKGU-01-01 TKGU-01-69 TKGU-01-56 TKGU-01-29 TKGU-01-29-01 TKGU-01-29-02 MGSU-01-24 TKGU-01-49 TPPU-01-52 TPPU-01-50 TPPU-01-51 TKGU-20-00 TKGU-20-01 TPPU-01-68 TPPU-01-67 MGSU-01-23 MGSU-23-60 TKGU-01-31 TKGU-01-28 TKGU-01-02 TKGU-01-02-01 TKGU-01-04 TKGU-01-01-03 MDSU-01-32 TKGU-01-11 TKGU-01-33 TMAU-11-20 TKGU-01-64 TKGU-01-72 TKGU-01-53 MGSU-11-23 TKGU-01-43 DESCRIPTION
Body Center Trim Top Trim Fluorescent Lamp Ass’y Fluorescent Lamp Lamp Starter (Glow Lamp) Name Plate Plexi Speaker Grill Monitor Support Bar Monitor Mounting Brkt Left Monitor Mounting Brkt Right Video Monitor (20-5F) (Standard Scan) Video Picture Tube Blind Cardboard (Small) Blind Cardboard (Large) Front Screen Operation Panel Ass’y Draw Latch Coin Door Coin Selector Coin Switch Front Door Lock Cash Box CS Frame 120 W Ass’y Game Counter Service Switch CS Plate 120W (Only) Service Switch Bracket T Molding (White) Front Screen Frame (Lower) Side Decal Speaker 16cm (8 OHM)
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
IX. Reorder Parts List, Continued
Body Parts — Rear View (Fig. 5-2)
ITEM
ODNOANAONS PART NO.
TKGU-01-01-05 TKGU-01-03 TKGU-01-03-01 TKGU-01-05 MDST-21-11 MDSU-01-01-11 MDSU-01-01-12 MDSU-01-01-13 MDSU-23-35 TPPU-01-01-14 CHPU-01-01-15 TKGU-01-08 TKGU-01-10 TKGU-01-65 TKGU-11-08 TKGU-01-30 CHPU-01-01-10 TKGU-18-01 TKGU-09-01-01 TKGU-01-07 MGSU-11-05 TPPU-11-25 TKGU-11-17 MGSK-23-61 TPPU-01-67 TPPU-01-68 TKGU-20-00 TKGU-20-01 TKGU-10-01 TKGU-10-01E TKGU-01-01-02 TKGU-09-01-02 TKGU-09-01-03 TKGU-19-01-03 DESCRIPTION
Back Door Back Door Lock (Key #6510) Back Door Key Only (Key #6510) Cam A-lype (Back Door Lock) PC. Board Ass’y 062 FCC Shield Cover 062 44P FCC PC.B. Ass'y 062 36P FCC P.C.B. Ass’y Snap In Fastener FCC Sponge (Black) Shield Cover Label Power Cord 5M Strain Relief Bushing Strain Relief Bushing Plate Fuse 5A 125V Caster Shield Cage (054 Type) Power Supply PP-7B Power Transformer PT821B Back Door Lock Stopper Plate Back Door Label FCC Label Monitor Adjustment Label MGSK Operation Manual Blind Cardboard (Large) Blind Cardboard (Small) Video Monitor (20-EZV) (Standard Scan) Video Picture Tube Power On/Off Switch Ass’y (90 ~ 120v) Power On/Off Switch Ass’y (200 ~ 240v) Transformer Base 100v Outlet (From Transformer) Terminal Block 6-Position Terminal Block 4-Position
Rear View of Game Cabinet
Operation Panel Assembly (Fig. 5-3) ITEM PART NO. DESCRIPTION
| 1 | MDST-14-12 | 8 Way Control Lever Assembly |
| 2 | TKGU-23-21 | Switch Collar |
| 3 | TNX-23-18 | 8 Way Guide Plate |
| 4 | TKGU-23-17 | Switch Spacer |
| 5 | TKGU-23-16 | Bearing Brkt |
| 6 | TKGU-23-20 | Spring Stopper |
| 7 | TKGU-23-22 | Lever Spring |
| 8 | TKGU-23-23 | E-Ring |
| 9 | TKGU-23-13 | Micro Switch |
| 10 | TMAU-12-15 | Lever Plate |
| 1 | TMAU-12-14 | Control Knob Plate |
| 12 | TMAU-12-16 | Control Knob Collar 8L |
| 13 | TMAU-11-18 | Knob with Shaft 80.5L |
| 14 | MGSU-01-22 | Operation Panel Base |
| 15 | TKGU-23-12 | Switch Button Bracket |
| 16 | TMAU-34-18 | Micro Switch VL 12L (Straight) |
| 17 | MDSU-12-17 | Black Sponge, 2 x 10 x 580L |
| 18 | TKGU-23-26 | Nut Plate |
| 19 | TKGU-23-34 | Pal Nut M16 |
| 20 | MDST-12-21 | Button Assembly (Black) |
| 21 | MDST-12-17 | Button Assembly (Crimson) |
| 22 | TMAK-11-19 | Operation Panel Fastener |
| 23 | TMAU-12-18 | Collar — 34 x 28 x 7H |
| 24 | MDST-12-24 | Button Assembly (Light Blue) |
| 25 | MDST-12-27 | Button Assembly (Green) |
VS. UniSystem Operation Panel Assembly Parts (Upright)
5-3
Operation Panel Assembly
Wiring Harnesses
PART NO. DESCRIPTION
MDSU-41-12 062 44P FCC Harness MDSU-41-11 062 36P FCC Harness MGSU-41-13 UP-072-44P Edge Harness MGSU-41-14. UP-072-36P Edge Harness MGSU-42-11 UP-072-15P Switch Harness MGSU-42-12 UP-072-12P Switch Harness MGSK-43-01 072-6P-100 Video Harness MGSK-43-02 072-2P-100 Audio Harness MGSK-43-03 072-4P-100 Service Sw. Harness MGSK-43-04 072-4P-100 Coin Sw. Harness MGSK-43-05 072-3P-100 Counter Harness MGSK-43-06 072-9P-250 Power Harness TKGU-13-17 2P-860 Speaker Harness
MDS P.C. Board Assembly PART NO. DESCRIPTION (Reference Designations and Locations) MDST-21-11 P.C. Board Assembly
| MDST-21-12 | 2A03 Microprocessor | (2J,8J) | |
| MDST-21-13 | HM6116 | 2k x 8bit Static RAM, 250ns | (6E) |
| MDST-21-14 | MB8416-15 2k x 8bit Static CMOS RAM 150ns | (8L) | |
| MDST-21-15 | TC5533P-A 4k x 8bit Static RAM | (2C) | |
| MDST-21-16 | TC5533P-B 4k x 8bit Static RAM | (8C) | |
| MDST-21-17 | 74LS00 Quad 2-input NAND LS TTL | (4C, 5C) | |
| MDST-21-18 | 74LS04 Hex Inverters LS TTL | (1L, 2K, 4E, 5E) | |
| MDST-21-19 | 74LS10 Tri 3-input NAND LS TTL | (4D) | |
| MDST-21-20 | 74LS32 Hex 2-input AND LS TTL | (4A, 4B, 5A, 5B) | |
| MDST-21-21 | 74LS74 Dual D-Flip Flops LS TTL | (5D) | |
| MDST-21-22 | 74LS123 Dual Retriggable Single Shots LS TTL | (1d) | |
| MDST-21-23 | 74LS138 Dual 2 to 4 Demultiplexers LS TTL | (1F, 6F) | |
| MDST-21-24 | 74LS157 2 to 1 Data Selectors LS TTL | (5J, 5K, 6J, 6K) | |
| MDST-21-25 | 74LS165 8bit Shift register LS TTL | (6M, 6N, 7P, 8P) | |
| MDST-21-26 | 74LS240 Octal 3 State Bus. Inverters LS TTL | (7M, 7N, 8M, 8N) | |
| MDST-21-27 | 74LS245 Octal 3 State Bus Transceivers LS TTL | (3K, 8K) | |
| MDST-21-28 | 74LS373 Octal 3 State D-Latchs LS TTL | (2E, 8E) | |
| MDST-21-29 | 74F04 Hex Inverters FAST TTL | (5H) | |
| MDST-21-30 | 4066 Quad Analog Switches C-MOS | (2P, 4P) | |
| MDST-21-31 | LM324 Hex Operational Amplifiers | (1P, 3P) | |
| MDST-21-32 | LM3900 Hex Operational Amplifiers | (5N, 5R) | |
| MDST-21-33 | PST518A Reset IC | (1K) | |
| MDST-21-34 | 2SA933 Silicon PNP Transistor | (Q3, Q7, Q13 ~ Q16, Q19 ~ Q22, Q26, Q27) |
MDST-21-35 2SC1740 Silicon NPN Transistor (Q1, Q2, Q4 ~ Q6, Q8, QY, Q12, Q17, Q18, Q23 ~ Q25) MDST-21-36 2SD592 Silicon NPN Transistor (Q10, Q11) MDST-21-37 18953 Silicon Switching Diode (D1, D2, D5, D7, D9~ D11)
| MDST-21-38 | W03B Silicon Diode | (D3, D4, D6, D8) | |
| MDST-21-39 | 27 Q1/4W + 5% Resistor | (R4) | |
| MDST-21-40 | 33 21/4W + 5% Resistor | (R22, R30, R36, R38, R45 | R47, R72, R89) |
MDSF-21-41 100 21/4W + 5% Resistor (R79, R80, R95, R97) MDST-21-42 330 21/4W + 5% Resistor (R8, R20, R28, R29, R48, R49, R70, R71, R73, R91)
| MDST-21-43 | 680 21/4W + 5% Resistor | (R119) |
MDST-21-44 1K 21/4W + 5% Resistor (R31, R32, R92, R93) MDST-21-45 1.2K 21/4W + 5% Resistor (R37, R43) MDST-21-46 2.2K 21/4W + 5% Resistor (R6, R11, R12, R14, R15, R23, R24, R27, R39 ~R42, R50, R51, R54, R55, R64, R65, R68, R69, R81, R87)
| MDST-21-47 | 3.3K 21/4W + 5% Resistor | (R77) |
| MDST-21-48 | 4.7K Q1/4W + 5% Resistor | (R13, R17, R25, R26, R52, R53, R66, R67) |
MDS P.C. Board Assembly (continued) PART NO. DESCRIPTION (Reference Designations and Locations)
| MDST-21-49 | 10K 2 1/4W + 5% Resistor | (R3, R5, R7, R16, R18, R19, R21, R33, R56 |
R63, R75, R82, R83, R85, R86, R120)
| MDST-21-50 | 12K 21/4 W + 5% Resistor | (R76, R96, R98) |
| MDST-21-51 | 20K 21/4W + 5% Resistor | (R94, R99) |
| MDST-21-52 | 33K 21/4W + 5% Resistor | (R1, R2) |
MDST-21-53 100K 2 1/4W + 5% Resistor (R10, R35, R84, R103, R121)
| MDST-21-54 | 150K 2 1/4W + 5% Resistor | (R74, R118) |
| MDST-21-55 | 360K 21/4 W + 5% Resistor | (R107, R114) |
MDST-21-56 750K 21/4W + 5% Resistor (R101, R108, R109, R110, R115, R116) MDST-21-57 1M 21/4W + 5% Resistor (R102, R106, R112, R117)
| MDST-21-58 | 1.8M 21/4W + 5% Resistor | (R90, R105) | |
| MDST-21-59 | 2.2M Q1/4W + 5% Resistor | (R81, R87, R100, R104) | |
| MDST-21-60 | 1K 2x8 | Series Resistor Array | (RM1, RM2, RM5, RM8, RM11, RM14, RM17) |
MDST-21-61 68 2 x 4 Parallel Resistor Array (RM3, RM4, RM6, RM7, RM9, RM10, RM12, RM13, RM15, RM16)
| MDST-21-62 | 33pF 50V Ceramic Disc Capacitor | (C35, C91, C92) |
| MDST-21-63 | 68pF 50V Ceramic Disc Capacitor | (C25, C86) |
| MDST-21-64 | 100pF 50V Ceramic Disc Capacitor | (C38, C42, C43, C46) |
| MDST-21-65 | 220pF 50V Ceramic Disc Capacitor | (C26 ~ 29, C34, C45) |
| MDST-21-66 | 0.01 p F 50V Ceramic Disc Capacitor | (C9, C10, C89, C90) |
| MDST-21-67 | 0.1 p F 25V Ceramic Disc Capacitor | (C100 ~C178) |
| MDST-21-68 | 0.2 p F 12V Cerarnic Disc Capacitor | (C4, C12) |
| MDST-21-69 | 0.047 p F 50V Film Capacitor | (C37, C39, C40, C44) |
| MDST-21-70 | 3.3 uw F 16V Al. Electrolytic Capacitor | (C15 ~ C18, C31, C32) |
| MDST-21-71 | 10 p F 16V AI. Electrolytic Capacitor | (C3, C5, C6, C11, C13, C14, C19 ~ C24, C30, |
C33, C36, C41, C47 ~ C85)
| MDST-21-72 | 47 p F 16V Al. Electrolytic Capacitor | (C2) |
| MDST-21-73 | 100 p F 16V Al. Electrolytic Capacitor | (C1) |
| MDST-21-74 | 100 # F 25V Al. Electrolytic Capacitor | (C8) |
| MDST-21-75 | 470 p F 16V Al. Electrolytic Capacitor | (C7, C87, C88) |
| MDST-21-76 | 500 © Variable Resistor. Red Cap | (VR1, VR3) |
| MDST-21-77 | 500 Q Variable Resistor. Green Cap | (VR2, VR4) |
| MDST-21-78 | 500 Q Variable Resistor. Blue Cap | (VR5, VR6) |
| MDST-21-79 | 21.47727MHz Crystal | (X1) |
| MDST-21-80 | 8 position dip switch | (SW1, SW2) |
| MDST-21-81 | 28P IC socket | (1A, 1B, 1C, 1D, 2A, 6A, 6B, 6C, 6D, 8A, 8B) |
| MDST-21-82 | 40P IC socket | (2F, 2J, 8F, 8J) |
MDST-21-83 Type 32-4 (UMS x 2) Battery Case MDST-21-84 Bolt with washer M2.6 MDST-21-85 Flat washer M2.6 MDST-21-86 Nut Plate M2.6 MDST-21-87 Dry Battery “AA’”’ T18L Beaded tie
Power Supply Parts (PP7B)
Part No. Description
| TKG-18-01 | (PP-7B) Power Supply | Complete |
| TKG-18-02 | Transistor | 2S8C2555 |
| TKG-18-03 | Transistor | 2SA817 |
| TKG-18-04 | Transistor | 28C2535 |
| TKG-18-05 | Transistor | 2SA1015 |
| TKG-18-06 | Fast Recovery Center Tap Diode | CTU-2S |
| TKG-18-07 | Shot Key Diode | CTB33S |
| TKG-18-08 | Silicon Rectifier Diode | S4VB40 4A 400VW |
| TKG-18-09 | Silicon Rectifier Diode | 1B4B41 |
| TKG-18-10 | Hybrid IC | 3D-1001 |
| TKG-18-11 | 3 Terminals Regulators | 7824 |
| TKG-18-12 | 3 Terminals Regulators | 7812 |
| TKG-18-13 | Thyristors | 5P4M |
| TKG-18-14 | Thyristors | 03P05M |
| TKG-18-15 | Diode | 18954 |
| TKG-18-16 | Diode | 10DF-4 |
| TKG-18-17 | Photo Coupler | PC614 |
| TKG-18-18 | Zener Diode | 05Z5.6U |
| TKG-18-19 | Zener Diode | 0525.1L |
| TKG-18-20 | Zener Diode | 05Z5.6Z |
| TKG-18-21 | Ceramic Capacitor | DE0707B471K2K 470pF2KV |
| TKG-18-22 | Ceramic Capacitor | 0.1MF 50V |
| TKG-18-23 | Film Capacitor | MDD2J473M 0.074MF 630VW |
| TKG-18-24 | Film Capacitor | 0.01MF 50V |
| TKG-18-25 | Film Capacitor | 1000pF 50V |
| TKG-18-26 | Aluminum Electrolytic Capacitor | 1000MF 50V |
| TKG-18-27 | Aluminum Electrolytic Capacitor | 47MF 35V |
| TKG-18-28 | Aluminum Electrolytic Capacitor | 47MF 16V |
| TKG-18-29 | Aluminum Electrolytic Capacitor | 3300MF 10V |
| TKG-18-30 | Aluminum Electrolytic Capacitor | 100MF 25V |
| TKG-18-31 | Aluminum Electrolytic Capacitor | 10MF 16V |
| TKG-18-32 | Aluminum Electrolytic Capacitor | 330MF 200V |
| TKG-18-33 | Aluminum Electrolytic Capacitor | 1000MF 25V |
| TKG-18-34 | Resistor (Coil Winding) | 20 OHM 2W |
| TKG-18-35 | Resistor (Carbon) | 1K OHM 14W + 5% |
| TKG-18-36 | Resistor (Carbon) | 51 OHM 4W+5% |
| TKG-18-37 | Resistor (Carbon) | 12 OHM 1hW+5% |
| TKG-18-38 | Resistor (Carbon) | 470 OHM 14W + 5% |
| TKG-18-39 | Resistor (Carbon) | 22 OHM "2W+5% |
| TKG-18-40 | Resistor (Carbon) | 20K OHM VeW + 5% |
Power Supply Parts (PP7B), continued
Part No. Description
| TKG-18-41 | Resistor (Carbon) | 100 OHM ‘/2W |
| TKG-18-42 | Resistor (Cement) | 20 OHM 5W |
| TKG-18-43 | Resistor (Metal Oxide) | 510 OHM 3W |
| TKG-18-44 | Variable Resistor | 50K OHM GFO6P |
| TKG-18-45 | Variable Resistor | 2K OHM GFO6P |
| TKG-18-46 | Shunt Resistor | 5m OHM |
| TKG-18-47 | SC Coil | SC-02 |
| TKG-18-48 | SF Coil | 100MH 5A |
| TKG-18-49 | SF Coil | 800MH 2A |
| TKG-18-50 | Oscillator Transformer | EC-35 Type 3D-0097 |
| TKG-18-51 | Oscillator Transformer | El-30 Type 3D-0097 |
| TKG-18-52 | Oscillator Transformer | EE-16 Type 3D-1000 |
| TKG-18-53 | Fuse Element | FGMB 4A 125V NR Type |
MONITOR PARTS (20-EZV) MONITOR PARTS (20-EZV), CONTINUED PART # DESCRIPTION PART # DESCRIPTION
| MON-01-01 | IC LA1464 | MON-09-06 | CERAMIC CAPACITOR 820PF 500V |
| MON-01-03 | IC LAS112 | MON-09-08 | CERAMIC CAPACITOR 1000 PF 1000V |
| MON-02-01 | DIODE 181555 | MON-09-10 | CERAMIC CAPACITOR 200PF 2000V |
| MON-02-02 | DIODE 181553 | MON-09-12 | CERAMIC CAPACITOR 500PF 2000V |
| MON-02-03 | DIODE EU-1 | MON-09-50 | ELECTRO CAPACITOR 47MF 10V |
| MON-02-04 | DIODE RU2 | MON-09-52 | ELECTRO CAPACITOR 470MF 10V |
| MON-02-05 | DIODE SIB01-02 | MON-09-54 | ELECTRO CAPACITOR 100MF 16V |
| MON-02-06 | DIODE ERCO04-06 | MON-09-56 | ELECTRO CAPACITOR 220MF 16V |
| MON-02-07 | DIODE 1S188TV | MON-09-58 | ELECTRO CAPACITOR 4.7MF 25V |
| MON-02-50 | ZENER DIODE EQA01-35 | MON-09-60 | ELECTRO CAPACITOR 220MF 25V |
| MON-02-51 | ZENER DIODE EQA01-07 | MON-09-62 | ELECTRO CAPACITOR 330MF 25V |
| MON-02-52 | ZENER DIODE EQA01-12 | MON-09-64 | ELECTRO CAPACITOR 1MF 160V |
| MON-02-53 | ZENER DIODE HZ7 | MON-09-66 | ELECTRO CAPACITOR 10MF 160V |
| MON-03-01 | TRANSISTOR 2SA673(A) | MON-09-68 | ELECTRO CAPACITOR 100MF 160V |
| MON-03-02 | TRANSISTOR 2SA940 | MON-09-70 | ELECTRO CAPACITOR 470MF 160V |
| MON-03-03 | TRANSISTOR 2SA659 | MON-10-00 | MYLAR CAPACITOR 0.047MF 100V |
| MON-03-51 | TRANSISTOR 2SC536 | MON-10-02 | MYLAR CAPACITOR 0.082MF S0V |
| MON-03-52 | TRANSISTOR 2SC2551 | MON-10-04 | MYLAR CAPACITOR 2700PF 50V |
| MON-03-53 | TRANSISTOR 2SC1015 | MON-10-06 | MYLAR CAPACITOR 0.33MF 50V |
| MON-03-54 | TRANSISTOR 2SC1051 | MON-10-08 | MYLAR CAPACITOR 0.1MF 50V |
| MON-03-55 | TRANSISTOR 2SC1507 | MON-10-10 | MYLAR CAPACITOR 8200PF 50V |
| MON-03-56 | TRANSISTOR 2SC2073 | MON-10-12 | MYLAR CAPACITOR 0.015MF 50V |
| MON-03-57 | TRANSISTOR 2802228 | MON-10-14 | MYLAR CAPACITOR 0.056MF 50V |
| MON-03-58 | TRANSISTOR 2SC2271 | MON-10-16 | MYLAR CAPACITOR 0.068MF 50V |
| MON-03-76 | TRANSISTOR 2SD386-AY | MON-10-30 | POLYPRO CAPACITOR 0.056MF 160V |
| MON-03-77 | TRANSISTOR 2SD870 | MON-10-32 | POLYPRO CAPACITOR 0.47MF 200V |
| MON-03-78 | TRANSISTOR 28D1090 | MON-10-34 | POLYPRO CAPACITOR 0.022MF 200V |
| MON-03-79 | TRANSISTOR 2SD901 | MON-10-36 | POLYPRO CAPACITOR 2200PF 630V |
| MON-03-80 | TRANSISTOR 2SD869 | MON-10-38 | POLYPRO CAPACITOR 6800PF 2000V |
| MON-05-01 | FUSE RESISTOR 1W 39 OHM | MON-11-00 | SOLID RESISTOR 1/2W 1.8 KOHM |
| MON-05-02 | FUSE RESISTOR 2W 330 OHM | MON-11-30 | CARBON RESISTOR 1.2W 100 OHM |
| MON-05-03 | FUSE RESISTOR 1/2W 1 KOHM | MON-11-32 | CARBON RESISTOR 1/2W 1 KOHM |
| MON-05-04 | FUSE RESISTOR 1W 3.3 OHM | MON-11-34 | CARBON RESISTOR 1/2W 10 KOHM |
| MON-05-08 | 3 KOHM VARIABLE RESISTOR | MON-11-36 | CARBON RESISTOR 1/2W 120 OHM |
| MON-05-10 | 10 KOHM VARIABLE RESISTOR | MON-11-38 | CARBON RESISTOR 1/2W 18 OHM |
| MON-05-12 | 50 KOHM VARIABLE RESISTOR | MON-11-40 | CARBON RESISTOR 1/2W 39 KOHM |
| MON-05-14 | 200 KOHM VARIABLE RESISTOR | MON-12-00 | WIRE WD RESISTOR 20W 180 OHM |
| MON-05-16 | 450 OHM VARIABLE RESISTOR | MON-12-02 | WIRE WD RESISTOR 7W 470 OHM |
| MON-05-18 | 300 OHM VARIABLE RESISTOR | MON-12-04 | WIRE WD RESISTOR 7W 1.5 OHM |
| MON-06-01 | TRANSFORMER A7007 | MON-12-30 | OXIDE M RESISTOR 1W 1 KOHM |
| MON-06-02 | LINEARITY COIL (A0285) | MON-12-32 | OXIDE M RESISTOR 1W 18 KOHM |
| MON-06-04 | WIDTH COIL (A7018) | MON-12-34 | OXIDE M RESISTOR 1W 330 OHM |
| MON-06-05 | FILTER COIL (L7133) | MON-12-36 | OXIDE M RESISTOR 1W 8.2 KOHM |
| MON-08-06 | LINE FILTER (LO19D) | MON-12-38 | OXIDE M RESISTOR 2W 10 KOHM |
| MON-06-21 | FLYBACK TRANSFORMER F5024 | MON-12-40 | OXIDE M RESISTOR 2W 5.6 KOHM |
| MON-06-50 | YOKE COIL (20-5F TYPE) | MON-12-42 | OXIDE M RESISTOR 3W 1.2 KOHM |
| MON-06-60 | PURITY MAGNET ASSY (20-5F) | TKGU-20-01 | VIDEO PICTURE TUBE (510UTB22) |
| MON-07-01 | FUSE 4A | TKGU-20-02 | MONITOR MAIN PCB |
| MON-07-02 | FUSE 0.3A | (W/ICOMPONENTS) | |
| MON-08-01 | THERMIST SDT-500 | TKGU-20-03 | MONITOR AUDIO PCB |
| MON-08-02 | THERMIST SDT-1000 | (WICOMPONENTS) | |
| MON-08-50 | POSISTOR PTH451C05 | TKGU-20-04 | MONITOR CRT PCB (W/COMPONENTS) |
| MON-09-00 | CERAMIC CAPACITOR 5PF 50V | TKGU-20-07 | MONITOR INVERTER PCB |
| MON-09-02 | CERAMIC CAPACITOR 470PF 500V | (WICOMPONENTS) |
MON-09-04 CERAMIC CAPACITOR 4700 PF 500V
PRINTED IN U.S.A.
©) ©
/21 PSvae | | reooso08} Loew} Luan |
im
©
PICTURE TUBE COLOR GUNS
12V(from 108VDC) 23 into sync amp/separator 12V(from 16VDC) 24 (vert. supply)
into hold down circuitry com
Sie richie
2:
DEFLECTION YOKE HIGH OL TAG
Description of Video Monitor Block Diagram
. 100VAC is applied . Rectified by D601, 602, 603, 604 . 1C601/TR901 form regulator for B + . B+ is distributed
G, R, B color signals applied . Amplified by the respective transistors . Amplified again at neck board . Bias provided by brightness voltage . Applied to picture tube guns
. Sync is applied, buffered by TR204 . Apply sync to 1464 sync amp & seperator
. Vertical pulse out of pin 5 is amplified by TR401, then by TR402/403 . Vertical pulse applied to deflection yoke
. Horizontal drive pulse out of pin 10 is amplified by TR451 . Amplified again by TR902 (horizontal output) . Applied to flyback transformer which distributes voltages
. Feedback from flyback monitors pin 7 pulse and will apply hold-down pulse to pin 9 of 1464 should over voltage exist
eeonivianst PICTURE TUBE SOCKET BOARD utes?
=Beecoe CONTROL CIRCUIT BOARD UBB5493
or
veo Gan 8H 6 GK TO MAIN CHASSIS CIRCUIT BOARD
“FROM MAIN CHASSIS CIRCUIT BOARD
vers, ourrur. an
3308
Sse bd LT sor
woRiz. ORIVE Rast 25032720, Beate)
MAIN CHASSIS CIRCUIT BOARD _U 885486 crx f B0NG SE, HOR Ego" far ie youan ns iter
t
cag aaa eee [2K ay ok 7 nase uss ooo FS Cade gt | Bein nace. 700° 7
2200 Jove 20006 dteop roop “S00
tai Tiel y630 “£6 3334 a jan) every 7 f Ayprowar ERY} cuszsoety amd
Kae
- TRANSISTOR BASE INFORMATION.
<. 250000 _ BE.
= ES
mm ase ad BS Ea = : = Ne ~
- RESISTOR, CAPACITOR: INFORMATION. ‘+ RESISTOR — INFORMATION. F io I “ES nesiston LS nesston vatue ina. POWER RATING. AS TO 1/4W F-TYPE RESISTORS, RESIST. ANCE VALUES ALONE ARE GIVEN. SoqCAPACITOR — INFORMATION EXPRESSED IN P WHEN THE UNIT ISPE OTHERWISE OMITTED. ‘RATING VOLTAGE (THE UNIT “V" OR "WV" IS OMITTED.) AS TO “SOV. C-TYPE” CAPACITORS VALUE IS ONLY GIVEN.
- THIS BEING A FUNDAMENTAL SCHEMATIC ‘THERE WILL BE SOME CASES THAT THE REAL CIRCUIT DOES NOT COINCIDE WITH THIS.
RESISTOR TYPE F; INSULATED FIXED CARBON FILM RESISTOR. NN: INSULATED METAL FILM FIXED RESISTOR, R; INSULATED FIXED METAL OXIDE FILM RESISTOR.
: FIXED CARBON COMPOSITION RESISTOR.
CAPACITOR Ty:
FIXED CERAMIC CAPACITOR, RADIAL TYPE ALUMINUM ELECTROLYTIC GaPaciTOR £ ; POLYESTER FILM CAPACITOR } POLYPROPYLENE FILit CAPACITOR, INP); NON-POLAR ALUMINUY ELECTROLYTIC CAPACITOR,
20-EZV(R-C) SCHEMATIC
©1982 Nintendo of America Inc. Hinman
fa
SWITCHING POWER SUPPLY
Block Diagram
LOOVAC is stepped down and rectified
vcc (12VDC) is applied to ICl; starts switching
ICl switching drives TR2/T3, which in turn drives TR1/
Secondary of Tl output is rectified by D4 & DS
After filtering, D5 output is -5V
D4 output supplies 3 terminal regulator 7824
7824 output is +24V; also drives 3 terminal regulator 7812
7812 output is +12V; also VCC for IC2
IC2 switching drives TR4/T4; which in turn drives TR3/T2
D9 rectifies T2 output which becomes +5V @OOOOOOOOOO
Trouble Shooting chart for PP-7B
ALL VOLTAGES
AC INPUT
CHECK 5s FUSE & AI
REMOVE SCR2 CHECK VOLT. WITHIN LIMITS: Yes Bad
CHECK Ic3, ica, 04,05 02,03
CHECK 07,08,D9 CHECK 1C1, Ic2 & assoc. cIRCUITS CHECK 201, ZD2 & ASSOC. SHUT-| DOWN CIRCUIT CHECK D2, D7 SCcR1, D1
TR
NO OUTPUT
+5, *12,+24 NO OUTPUT +5 VOLTS
CHECK L5,D9,
ice NO OUTPUT
-5 VOLTS
CHECK L2,L3
1c3, Ica
ip 8047; 650vw
E16 Tr8 25A817
O14 1$95¢
FG
cas 6.047 ar 639vw
20, 1221)
a8
Tr3 2SA817 3BFWJ2CI
; § on ~O+5V
E Pose TS Tra 25asmy_|
S UL Power Supply (PP=74) a 1$.56,9,25)
eS (ena) ee SOILVWSHOS AlddNS YSAMOd
FG BRI save: Rs fo De 18954 cc35 cTv-25,
anv ut sce2
aky
ca + 68ety 6380
Gna aor [|| * of t c6,c7 xz® Ci C3 7,3] a‘ AT y%6V%3) 637
TS BR2 184841 R28 1K 13 Yen 22. GNO) 15, A201 S riz ts LASSE Pees ‘ ASSES te e Leoneas k L & ys
- ke Sr SCRE Rete ae [O8P85M
HV: ie, T2 E130
PG LI a s90Fe AK
Kis < 535 Té EEG
Rig ot wet R28 ewe 3 08 190F-4 GND
lo S Zeicrscrace9re | 47 tov
GNO a's
+5V
(FAB I36.9.25
~ A mame WlSne GR
44P Edge Connector 062 40P FCC Connector ‘9
HD a ——s a en GND ‘EN GND
| tet — eno | t | so | Te | |
| té | am | if | Vv | [oa |
| ts | 7 | 2, | cy | |
| 3 | 150 | a | Ey |
av +72V
| fa Rel | av | + | oi | 2 |
Hav {+ E| E co
| Seon | + | Seon | 77 | |
| amcor | a | wicom | Zl | |
| SCON?, | + | ‘sconz | cs | |
| Fel coma | + | = | peo | 2 |
| SRED. | + | Fo | SED | |
| MRED | 1G. | a: | ||
| S GREEN, | + | rea | Sane: |
M GREEN * a. VIDEO GNO v1 S BLUE fe
| M BLUE | an | re |
| SYNC | + | ro |
| MSYNC | + | Le |
i
| av | — | + | aa |
| 7 | = | + | 'S COUNTER, |
COUNTER ‘M COUNTER M COUNTER ¢
| kl 'S SERVICE, | to | fea ue |
| M SERVICE | 7 | Sev |
| '$ SOUND | ! | Ss0uN0. |
| ‘MSOUND, | + | sour |
‘GND ox = = GHO ow = AE CEOELECEEEG
SCHEMATIC
owe 3710/84 062 44P FCC PC Board Nintendo of America Inc
MDS PCB
Be
062 44P FCC HARNESS
1 ‘ENO eae ry GND Sek ae A te Gi ‘BLACK ele te Ea suck} +H Het FE RED re HY
RED E =— ete 2
ED 12v ORANGE He ts ry PAmert segn 5 M_COIN, ee s Sone ced a i se RED tS Sa BED : FH es o 2 S GREEN BROWN Ris Sanko1 snow a Ho) 44 V. GND YELLOW QO bl a a| too YELLOW 0 aKa} ———— t @ M BLUE RANGE earn our
UE ee ao § = + |
- ORANGE cr “2a ORANGE q AF ‘M COUNTER, BROWN et o
- vetow E) ‘SS SERVICE ST ‘M SOUND +} ‘S'SOUND A
aRown RA = on oe BLACK GND BLACK.
062 36P FCC HARNESS
4 a eae i= ne fat = ‘S1 RIGHT BROWN. ‘M1 RIGHT BROWN tet [St ——sicerr RED HF 3 SiUP ta; stor aae—tets) [S| — steam veiw 99h Q ni LE}. gaa YELLOW Le} eco —\vertow once 9 o rey 2 ere ee as 8 $1 B SWITCH MGT BLUE. 5S ed ts] ta ae 1818 Lo J re PURPLE ial =a
“GRAY SELECT a © fra ‘$2 RIGHT a i iH erown j25/25) ay mJ ‘RED q | Bt aaa o
ORANGE: 0 Aa! YELLOW [| [ss | m2 Gown row ie [esse aswircw Seay T M2 A SWITCH GRAY Be an wat eal ‘M2 B SWITCH GB se BLACK. Le ava oe BLACK fs!
Vv
44P Edge Harness Connector 36P Edge Harness Connector Pai q a < QO; oO; Fs of oe 3/10/84 062 FCC PC Board Nintendo of America Inc.
BROWN
M COIN 2,
‘M GREEN RED
YELLOW GREEN
ORANGE RED YELLOW
WW & ORANGE
om “awe
| ae | | | PURPLE. | BROWN | 7h | GND |
| a | <5v | ORANGE | RED | az | GND |
| [a | | ORANGE | 3t3 | GND | ||
| D | +5 | YELLOW | YELLOW | 12 | |
| 5 | +12 | 4 |
GREEN GREEN
| +12V | 5 | ov |
| BLUE | 3 | av |
| PURPLE | it | +5V |
BROWN [a]
| ‘SCOINT | WHITE | wav |
| MCOINT | RED | 9 |
‘SCOIN2 Power Supply o- RE a ls er erie 7 Power Power Transformer switch fuse, ' 20 ote z ol2 a8 100 sov Powen coro
PP-78
ORANGE
‘M SOUND GND. [end [cnt [sno
[aq cnn [AT cu BROWN [2] [BE | miaicHT | [3 | S1LEFT & ORANGE a E{ moo — | veuowomm | LF | ‘M1 A SWITCH LBLUE ‘S18 SWITCH [He [ ipswich | [Bl ‘S SELECT 1 J M SELECT 1 [3] S SELECT 2 M SELECT 2 CRAY CJS SELECTS [i [ Msevects 4 4|___SSELECT4 M|___MSeLect4 BROWN
a [el wer ORANGE a szup i ee [a5] s2D0wn
Ss M2 DOWN GRAY
Gl S2 A SwitcH
M2 B SWITCH YELLOW
Service
BLACK ° bron rn
| / | oO | g | |
| S | 2 | i | H |
| e | o | H | q |
| 3 | a | 8 | 3 |
PA g e i rss Fa
| oF | | | . |
oO 8 >
VIDEO MONITOR pee eee ee een eee eee eee 4 SOUND P.C.B. I
| BROWN _F7t7}_ BROWN 5% nicht | ! | 4 | ||
| RED | rome, | 1 | ||
| {orange —}2}2{ nance Sot op” | 1 | H | ||
| K“"veutow “1331 veutow 5-2 | pown | oo | 1 | ||
| { se | GREEN | Ww | | | / |
Mee Roane | I
| era 14 GRAY | 2p SELECT 2 | | | t |
| wate 315 | an | alt | } |
| BLACK | a | az | i |
LT cn | ; Be | i \
| Y.GREEN | Y. GREEN | 1 |
| 3H 3} | Oo O-—A SWITCH | ' |
Cf teswue iaha L BLUE OO wre z ce, om
| ' | — | 1 | | |
H 1
| BROWN 1717} SROWN oO RIGHT | - | H | } |
| re) | FT | ' | |
| 1212|-onanae ss te | < | t | L-~. ~~~ -- |
YELLOW 1
| GREEN | 0-4 DOWN | a | ! |
I Lu 1 a
| RAY | a | ! | z | RED. |
| erat | OA SWITCH | 1 | ||
| BLACK | O-#8 SWITCH | (o} | H | Speaker |
' ' VIDEO MONITOR SIGNAL P.C.B.
VIDEO MONITOR MAIN P.C.B.
WIRING DIAGRAM
‘APPROVED 8 onawn ay TUK RevierD scat ears 2/10/85.
VS. UNISYSTEM UP
Nintendo of America Inc. |"Mas_k
we
nai 1083 | PIECED wd 12 13
+5V.3A ao ; oe Ff carp ara P2 PI 1@SQOFF0800R aus eae
QM? RICH D2 cert OzES Dez ur TET TOM Sy seu 9 SO ace tirerses
M1 RIGHT Onmtial ror Du ue Dy siz OED 6.5 1B Se [poche rwewee “Om a sw O-NurwaQgay o-vernonewss
ooNu suns saa
JIM cone
xin] ass) LA) comms {i]s sevice
@s2 ricH Yaimsze ass =O s0ut
wecars =z Dome @s2 ve Is S14 —@s sti? POsea
{ exe
~~ @s seus Dst5 5" nak Osrase averen
A
hdd O-nu rel SAy o-wusweveugs
EE awe swe SEATF o-wk senses
oe wenn Sear EI
oe 7807 se Run TR [ays cots 2 ©iM324 412 aay GND 11FIN “scans
$ SouNc (a406E 12 14pm GNG 6, 7em Gs service
THis custom,
‘ MOS-@2-CPU rm
EXSRK Nintendo Ge Sit Lid.