CATHODE RAY TOMES

Centipede TM-182 2nd Printing

Centipede (revision 4) (Atari, 1980) · Technical Manual · 64 pages · 44 sections · original scan

Page 1

MS), Operation, Maintenance

and Service Manual

Page 2

GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a silver identification label. If your game is UL-listed, this label is located on the front of the game, underneath the coin door. Otherwise, the label is affixed to the rear panel of the game. The same serial number is also stamped on the chassis of the monitor, Regulator/Audio || PCB, and the Centipede™ Game PCB. Please mention this number whenever calling your distributor for service.

GAME SERIAL NUMBER IDENTIFICATION TAG

REGULATORIAUDIO Il PCB CENTIPEDE GAME PCB

Page 3

(AOS ~y-enNar eS" ge 2 I NUIZES

Shp } : = = VY Ah CY, Operation, Maintenance y l 8 és and Service Manual NF oN Complete with Hilustrated Parts Lists

Page 4

Copyright © 1981 by Atari, Inc. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

Published by: ATARI, INC. 1265 Borregas Avenue PO. Box 427 Sunnyvale, California 94086

Lithographed in the U.S.A. 7K

Page 5

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

1.) you substitute non-Atari parts in your coin-operated game, or

2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 6

Table of Contents

Location Setup A. New FeatureS.... 0. cece cece eee e ene enna B. Game Inspection . C. Game Installation.

  • Voltage Plug Selection ..........
  • Interlock and Power On/Off Switches . D. Self-Test Procedure ............... E. Option Switch Settings .
  • Bonus Play Feature. .
  • Coin Mechanism Multipliers .
  • Examples of Game Price Settings . F. GamePlay
  • Attract Mode ODOOMRARAWOR
  • Ready-to-Play Mode . . 14
  • PlayMode ......... 14
  • High Score Initial Mode ........ 0.0... c cece eee eee 16

Maintenance and Repair A. Cleaning B. Fuse Replacement C. The Control Panel

  • LED Start-Switch Replacement ...
  • Leaf-Switch Replacement .
  • Mini-Trak Ball™ Maintenance and Repel .19 D. Monitor Removal o —. Printed-Circuit Board Removal . . 1, Game PCB Removal
  • Regulator/Audio I! PCB Removal ..... F. Fluorescent Tube and Speaker Replacement G. Game Operation

Illustrated Parts Lists IMustrations and paris lists begin on page .........-..0-e sees eee ee 27

Page 7

Centipéde™

List of Illustrations

Figure 1 Overview of Game 2 Figure 2 Installation Requirements . . . 3 Figure 3 International Voltage Plug Selection . 4 Figure 4 Interlock and Power OniOff Switches ............0. ec eee eee eens 5

Figure 5 Location of Self-Test Switch, Volume Control and Option Switches ... 6 Figure 6 Self-Test Procedure 7 Figure 7 Game Option Settings - 10 Figure 8 Game Price Settings ©0020... 2... cece eee eee eee 1

Figure 9 Coin Counter Option Settings ........ 06... cece eee e eee eens Figure 10 Opening the Control Panel and Replacing Switches . . Figure 11. Mini-Trak Ball™ Maintenance and Repair. Figure 12 Monitor Removal ............ 00. e cece eee eee eee nee ene

Figure 13 Printed-Circuit Board Removal .......... 00... ese e cece cece eens 22 Figure 14 Fluorescent Tube Replacement . . 23 Figure 15 Power Distribution ........ . 25 Figure 16 Signal Distribution ........ 2.0... c eee cee n eee eens 26

lustrated Parts Lists: Figure 17 Cabinet-Mounted Assemblies Figure 18 Control Panel Assembly... . Figure 19 = Mini-Trak Ball Assembly .... . : Figure 20 RegulatoriAudio II PCB Assembly ............... 0.0 cece eee eee 34

Figure 21 Centipede™ Game PCR Assembly ........... 206-0 s cece cece eee 36 Figure 22 Power Supply Assembly............ Figure 23 Fluorescent Light and Speaker Assembly AZ Figure 24 American-Made Coin Door.......... 7 ~ 44 Figure 25 British-Made Coin Door .... 2... 0... eee eee eee eee 48

Page 8
NOTE If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help® at the Atari Customer Service office in your geographicai area, as shown below.

WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) ex From California, Alaska or Hawaii (408) 745-2900 ee From anywhere else in this area toli-free (800) 538-1611

EAST U.S.A. Game sales and service only

Atari, Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey (201) 469-5993 s From anywhere else in this area toll-free (800) 526-3849

EUROPE Parts for all Atari customers in Western Europe. Game sales and service

Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)

@ 0062-52155

vi

Page 9

Location Setup

this assembly are Underwriters Laboratories Listed and Canadian Standards Association Certified. The addition of a foam pad on the rear access panel insures that the safety interlock switch will be completely closed when you lock this panel. Due to environmental factors, these panels can warp slightly, which could cause a switch to remain open. Additional Improvements: The wiring harness has been redesigned so that signal and power wiring are now separated to provide ease of maintenance and troubleshooting. Second, all monitors used are UL-Recognized and CSA-Certified, thus providing the most reliable and highest quality monitors available in the marketplace today. In addition, the power supply chassis has been A. New Features fitted with a metal bottom plate, making it a totally self-contained unit. The Centipede™ game has several new parts. Even if you are familiar with Atari games, you should

note these important differences. The new parts are: @ = Mini-Trak Ball™ Assembly. The widely used Trak Ball assembly has been redesigned. The basis for this compact, simplified design is a two-part moided plastic frame. Fewer parts in this control make servicing easier, and its very smooth action is designed for greater player accuracy. @ The circuitry has non-volatile memory for part of the high score table. This means that even if power is removed from the game, the three highest scores will permanently stay in memory. To erase these scores follow the instructions in Figure 6, Self-Test Procedure. @ To insure starting, the fluorescent light now includes a large grounded metal piate. In addition, the lampholder and ballast transformer used in Fourth, the attraction panel and monitor shield are now made of tempered glass to facilitate cleaning and improve visibility.
Page 10

MONITOR FLUORESCENT LIGHT SHIELD

ATTRACTION PANEL

COLOR MONITOR

aN MINI-TRAK BALL™ CONTROL

‘START: SWITCHES

CONTROL PANEL’ ; GAME PCB

REGULATORY AUDIO Il PCB COIN DOOR SS POWER SUPPLY

POWER ON/OFF QB SWITCH INTERLOCK SWITCH

Figure 1 Overview of Game

Page 11
WARNING: SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is mentioned, you will see this symbol:

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

NOTE | Do not plug the game in yet! |
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel, as well as the coin door, inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation. Place the square black plastic strainrelief plate in the wood slot at the bottom of the rear panel opening.
WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the monitor with your hands or metal objects held in your hands!

@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Centipede™ Game PCB, Regulator/Audio |! PCB and monitor are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and monitor for secure mounting.

Cc. Game Installation

Figure 2 Installation Requirements Power 130 watts Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 64x82 cm (25% x 32% in.) Game Height 181 om (71% in.)

Page 12
  • Voltage Selection If you live outside the United States, your Centipede™ game has the “international” power supply with three colored piugs. Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3.
  • Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed (see Figure 4). One is located behind the rear access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened. Check for proper operation of the interlock switches by performing the following steps: @ Be sure the access panel and the coin door are closed. @ Plug the AC line power cord into an AC outlet. @ Set the power on/off switch to the on position. Within approximately 30 seconds the monitor should display a picture. @ Slowly open the rear access panel. The monitor picture should disappear when the panel is opened approximately 2% cm (1 inch). Close and lock the access panel and repeat this step with the coin door. @ Ifthe results of the preceding step are satisfactory, the interlock switches are operating properly. lf the monitor doesn't go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the on position.

Line Voltage Range Voltage Selection Plug Color 90-110 VAC (100) Violet 105-135 VAC (120)* Yellow* 200-240 VAC (225) Blue 220-260 VAC (240) Brown *This is the only plug provided on the U.S. power supply. The international power supply includes the other three plugs.

voLTAGE © SELECTION

Figure 3

WARNING

Fuse cover must be in place during game operation.

International Voltage Plug Selection

Page 13

SAFETY INTERLOCK SWITCH

’ POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 14

D. Self-Test Procedure

This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the monitor, the light-emitting diodes in the start switches, and the game speaker; no additional equipment is necessary.

{| VOLUME INCREASE: < \ TURN CLOCKWISE

‘SELF-TEST SWITCH (EURO- PEAN GAMES) SELF-TEST SWITCH (US)

VOLUME CONTROL Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options.

To run the self-test, follow the instructions outlined in Figure 6.

Figure 5 Location of Self-Test Switch,

Volume Control and Option Switches

Page 15

Figure 6 Self-Test Procedure

Instruction Results if Test Passes (if results are not as indicated, ‘see list of failures that follows)

  • Begin: Set self-test switch to on position (see Figure 6).

2, Mini-Trak Ball Test: Roll the MiniTrak Ball controls in all directions.

  • Switch Test: One after another, activate and release all control-panel switches, the slam switch, and coin switches.*
  • Audio 0 Chip Test: One after another, press and hold 2 of the control-panel switches and at least one of the coin switches.

5, Audio /0 Channel Test: Press 1-player start button four times.

  • Background Color Test: Press 1-player start button at least 16 times.
  • Object Color Test: Press 2-player start button at least 16 times.
  • Moving Object Test: Watch the screen, and move the Mini-Trak Ball around. Place the moving object in an open area of the screen. Press fire button several times.
  • Erasing the High Score Table (optional) The monitor displays the picture below. The game produces no sound at all. The two start-switch LEDs wili stay on throughout self-test.

The centipede head moves around on the screen in directions corre- Sponding to Mini-Trak Bali contro}.

As long as you activate (close) each switch, you'll hear a high beep.

Volume increases and pitch decreases with each additional switch that is activated.

You'll hear a high beep for each press of the button.

Background color changes with each press of the 1-player start button.

Objects on playfield change color.

Each press of ihe fire button changes the moving object to another moving object. At certain points in the series, the object will disappear. This is not a failure indication. The current three highest scores are held in permanent memory, even if the game is y-S) unplugged. If you want to erase these scores, simultaneously press either fire and two. start buttons. The 4 FF message in the upper left corner of the screen will then be displayed. The average game time data will also be erased, but still displayed on the screen.

  • End: When satisfied with test, set self-test switch to off position.
  • Activate coin switches by inserting at least one coin in each coin slot. You will not trip the coin counters as long as you stay in self-test.

NO. OF LIVES AT START OF GAME

ALL SWITCHES & TRAK-BALL INPUTS

BONUS COIN SETTING (means “for every 3 coins inserted, logic adds 1 more coin”), Blank if no bonus coins(s) See Fig. 8 for switch settings.

1:5)

GAME DIFFICULTY SETTING ENTIRE CHARACTER SET oN Cc, RCOIN MECH MULTIPLIERS (L, R if you have a 2-mech coin door)

TOTAL NO. OF CREDITS PLAYED

AVG. GAME TIME PLays: GARE TIKE {accurate to +4 secs) proomnokeckrzzovene4ccz:

Page 16

Figure 6 Self-Test Procedure, continued

Results if Test Fails

  • Begin: RAM FAILURE is indicated by one to 10 beeps. Note the number of beeps and determine which RAM may be bad. To restart the test, press the reset pushbutton on the game PCB, or set the selftest switch to off, then again to the on position. Possible Bad Number of Beeps Given RAM Chip Location H2 CONG HRONS r Le

10 NS Any bad RAM must be replaced before the computer can check the other RAMs, as well as continue with the self-test.

ROM/PROM FAILURE is indicated by two groups of numbers in the upper left corner of the screen. The number at the far left indicates the location of the failing PROM/ROM(s). Identify the bad ROMI/PROM with the table below. If the screen displays “garbage,” or the logic produces strange audio or randomly activates. the coin counters, the chip at location J1 is probably bad. Ignore the hexadecimal numbers just to the right of the chiplocation number. Failing ROMIPROM Displayed Number Chip Location 0 DI 1 Et 2 FIH1

3 or “garbage” Jt AS

ae e5* 5 BIC/D3

*If you replace or erase this ROM, the number 4 FF will be displayed throughout the seif-test. The next time you enter self-test, the 4 disappears after a game is played. Otherwise the self-test will continue to display the numbers 4 FF.

  • Mini-Trak Ball Test: The character doesn’t move in same direction as ball, jumps rather than moves smoothly, or doesn’t move at ali. One of the Coupler PCBs in either Mini-Trak Ball control may be bad, harness wires or connector may be loose, Mini-Trak Ball reading circuitry on Game. PCB may be bad, or Mini-Trak Ball bearings may need oiling.
  • Switch Test: Sound is constantly on, even though you are not activating any switch. Or, no beep is given for any switch, or LED is dark. Indicates a bad switch, loose harness wires, bad LED-driving circuitry, volume turned all the way down, or loose connector.

4, Audio I/O Chip Test: No increase in volume or decrease in pitch indicates bad custom audio 1/0 chip at location B/C/D3.

  • Audio 0 Channel Test: On one out of the four activations, no audio is produced. Indicates ‘one channel is bad in the custom I/O audio chip at location BIC/D3 (replace entire chip).
  • Background Color Test: Background doesn’t change color, or doesn’t display all 16 colors. Indicates bad color RAM chip. (RAM failure would have been indicated earlier with from 3 through 10 beeps.)
  • Object Color Test: Objects don’t change color, or don't display all 16 colors. RAM failure.
  • Moving Object Test: Object doesn’t change to another object. ROM/RAM failure.
Page 17

E. Option Switch Settings

  • Bonus Play Feature Centipede™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

For example, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, will receive a bonus coin. Therefore, players receive 3 plays for $1.00.

This bonus feature encourages players to insert more money than just the minimum 50¢ you could require for one game. Various other bonuses are available (see Figure 8).

  • Coin Mechanism Multipliers Available since early in 1980, Atari games have a new coin door which has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a certain pattern.

The right coin mechs are all the same to the game’s logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech in a 3-mech door as the same. Refer to the diagram below.

[ese [si] fes¢] [fese| [Is1

This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game's logic. The basic unit of measurement is 25¢, which equals a multiplier of x 1. Therefore, if you have a 25¢/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x 1/x 4. (The left mech in a 3-mech door always has a value of x 1—you cannot change its value.)

You can set these multipliers with toggles 3 thru 5 on the Centipede Game PCB switch assembly at location N8. For exact settings of these toggles, refer to Figure 8.

  • Examples of Game

Price Settings

Figure 8 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned are all in the switch at location N8; they only relate to game price, coin mechanism multipliers, and bonus play. You should set the toggles relating to other functions as you see fit, although Figure 7, 8, and 9 provide ‘“‘$” signs indicating Atari’s recommendations.

Page 18

Figure 7 Game Option Settings To change toggie positions on the switch assemblies, you need not remove the game PGB. The switches, usually colored blue, are easily accessible when the Centipede Game PGB is mounted in place. When changing the options, verify proper results on the monitor display by performing the seli-test. Note that changing an option on any of the following eight toggles will not cause an immediate change on the monitor screen during the attract mode.

Toggle Settings of 8-Toggle Switch on Centipede Game PCB (CENTER switch assembly when PCB is in game) 8 7 6 5 4 3 2 (at N9)

1 Option

On On Off Oi

On On On Off

Off On

Off Off

On On On Off

ott Off On Off

On Off On English $ Off German On French Off Spanish 2 lives per game lives per game $ 4 lives per game 5 lives per game Bonus life granted ai every: 40,000 points 12,000 points $ 15,000 points 20,000 points

Hard game difficulty* AD

Easy game difficulty* $ t-credit minimum $ 2-credit minimum

$ Manufacturer's suggested settings *Refer to F. Game Play, for information on game difficulty.

24S For pricing for “credits,” see Figure 8 Changing toggles 3-7 erases the high score table.

Page 19

Figure 8 Game Price Settings

The white block below contains Atari's suggested settings. All Circled numbers refer to game pricing labels you should use numbers 1 thru 8 are toggle settings on the 8-toggle switch at lo- with each situation (labels are on the following page). Use the cation N8, on the Centipede™ Game PCB (the LEFT switch as- label no. 6 (indicated with )) only if you set toggle 8 at PCB switch assembly N9 to off. sembly}.

50¢ PER CREDIT

Bonus $.75 = 2 credits Bonus $1.00 = 3 credits

Straight 25¢ Door

25¢/$1.00 Door or 25¢/25¢/$1.00 Door

25¢ PER CREDIT

Bonus Bonus 3 credits $1.00 = 5 credits No bonus $.50

876
Straight@offofofoff

25¢ Door

4321
OffOffOn

25¢/$1.00 Door or 25¢/25¢/$1.00 Door

"1

Page 20
Figure8Game Price Settings, continued

The switch settings below relate to options for game price, coin mechanism multipliers, and bonus play. This information is useful in case you need to temporarily set the Centipede™ game on free play, or if you have German coin mechanisms in your door. To achieve bonus plays, all coins must be inserted before pressing the start button. The label no. 6 shown below should be used only if you set toggle 8 at PCB switch assembly N39 to off.

Toggle Settings of 8-Toggle Switch on Centipede PCB8 (at N8). LEFT switch when PCB is in game

87654321Option
OnOnFree play
OnOff1 coin* tor 2 credits
OffOn1coin* for1 credit$
OffOff2 coins* for 1 credit
OnOnRight coinmech x 1$
OnOffRight coin mech x 4
OffOnRight coin mech x 5
OffOffRight coin mech x 6
OnLeft coinmech x 1$

Off Left coin mech x 2

OnOnOnNo bonus coins$

On Off On On Off Off

OffOnOn

Off On Off

For every 2 coins* inserted, game logic adds 1 more coin* For every 4 coins* inserted, game logic adds 1 more coin* For every 4 coins* inserted, game logic adds 2 more soins*

For every 5 coins* inserted, game logic adds 1 more coin* For every 3 coins* inserted, game logic adds 1 more coin*

*In the U.S., a “coin” is defined as 25¢ In Germany a “coin” is 7DM.

$ Manufacturer's suggested settings

Game Pricing Labels

o 2 @@ 2 coins =1 play ATARI

°e

AS@1 coin=1 play

KO @ @ 2 coins = 1 play ATARI

@ @ @ @ 4 coins = 3 plays Ng @@ 2 coins AT’ 9 @@ 3 coins 000 @ 4 coins

©@@2 coins =1play
A@ $1coin =3plays

(Susan B. Anthony coin)

©, @ 1coin = 1 play ame’ 2 play minimum (2 coins = 2 plays)

(For operator use—write in the appropriate phrase. Use a permanent-ink water-resistant marker.)

Page 21

Figure 9 Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4-Toggle Switch on Game PCB (N11)

4321

Two coin acceptors in the coin door: Two coin acceptors and a pushbutton utility coin switch in the game (cocktail-table cabinet): Three coin acceptors in the coin door:

OnOnBoth acceptors activate all coin

counters simultaneously.

OnOffBoth acceptors activate 2 count-

ers separately. 3 2B S$ 3

Ss3OffOnBoth acceptors activate all coin
==counters simultaneously.
OffOffBoth acceptors activate 2 count-

ers separately. $ Do not use this setting.

Do not use this setting.

Utility coin switch will not activate a coin counter, if you do not hook it up. Both acceptors activate all coin counters simultaneously.

Utility coin switch will not activate a coin counter, if you do not hook it up. Left and right acceptors activate 2 coin counters se- Parately. All 3 are same denomination and they activate all coin counters simultaneously.

Left and center acceptor activate ‘one coin counter; right acceptor activates another coin counter.

Left acceptor activates one coin counter; center and right acceptor activate another coin counter. Not for any currently designed 3-mech coin door.

Left, center and right acceptors activate 3 coin counters separately.

$ Manufacturer's suggested settings

F. Game Play

Atari’s Centipede™ game is a one- or two-player game with a color raster-scan monitor. The fast-moving action includes a variety of creatures dropping down from the top of the screen or flying in from its sides, most of them to attack the player. The player’s shooter is represented on the screen by a somewhat humanoid head. The player’s goal is to shoot at and destroy as many of these creatures and mushrooms as possible for a high point score, before the player’s lives are used up. Players can maneuver their Mini-Trak Ball™ control anywhere within approximately the bottom fifth of the screen. However, they must move around mushrooms, since these are fixed, not “transparent”, objects. A fire button shoots individual shots upwards, or fires a hail of shots if pressed constantly. (Only one shot appears on the screen at atime.)

The game has five possible modes of operation: attract, ready-to-play, play, high score initial, and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled. Wait at least eight seconds after a game has been played before entering selftest or turning off the power. Otherwise, you may erase the high score table.

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test. In this mode, the monitor displays two pictures simultaneously.

One of the pictures is operator-selectable for one of four languages. Placed in the center of the screen, the picture shows the high score table, game price, and the bonus-life achievement level. If the operator sets the Centipede game for free play, the game will not display a game price message.

The high score table shows the eight highest scores and their matching initials. If you erase the special “permanent” memory (see Figure 6, Self- Test Procedure), then this table will contain fictitious scores and initials. The table is redeveloped from subsequent games with scores of more than 12,102 points. Subsection 4, High Score Initial Mode, explains this table in more detail.

Page 22

Operators may choose one- or two-credit minimums by selecting one of the option switch settings on the game PCB (see Figure 7, Game Option Settings).

If the game is set for a 2-credit minimum, that message will be displayed on the screen. (No special message appears if Centipede is set to the opposite setting, namely 1-credit minimum.)

The other picture surrounds the high score table, game price and bonus-life achievement level messages. That picture displays a typical game-play sequence, with a field of colorful mushrooms through which a centipede crawls. The spiders bounce in from the sides of the screen, and fleas occasionally drop down from the top. In addition, scorpions will cross the screen at almost any point.

In this mode, the action exactly duplicates a typical game played by a moderately skilled player: the player’s shooter moves freely within the limits of motion, shooting at spiders, centipedes, fleas and scorpions. Periodically the player is “destroyed” when a flea, spider or centipede head or body collides with the player’s shooter.

All the colors on the screen change with each wave. A new wave occurs when the player shoots all centipede parts remaining on the screen. At this point, a new centipede starts snaking its way down from the top of the screen.

The attract mode differs from real game piay in that no head figures are shown at the top of the screen to represent the number of lives remaining, no sounds are produced, no scores are incremented, and none of the four player controls work.

At any time when the game is powered up, if the coin-door slam switch is closed, you will hear a special alarm sound. This sound alerts location personnel that the game has been abused.

  • Ready-to-Play Mode This mode begins when sufficient coins are accepted for a one- or two-player game. It ends when the 1-player start or 2-player start pushbutton is pressed. When this mode begins, the message CRE- DITS __ is displayed in the middle of the screen. The pictures are otherwise the same as those shown in the attract mode.

If you select the two-credit minimum and a player inserts enough money for only one credit, the message 2 CREDIT MINIMUM flashes on the screen until enough coins for the second credit are inseried.

In addition, CREDITS 0% is displayed if you have selected the option of two coins per credit, and the player has inserted only one coin. A “credit” is defined as the cost for each player to play one game. In other words, two credits will pay for: @ one player playing two games, or @ two players playing one game.

  • Play Mode The play mode begins when any flashing start pushbutton is pressed. The mode ends when the player’s last life is lost.

A player's shooter is enabled at the beginning of the play mode, and the audio starts. The appropriate LED start switch will then stay lighted until the end of the game. At this point it will flash if any credit remains.

The game begins with a playfield of randomly placed mushrooms. A centipede starts snaking its way across from the center top of the screen. The centipede changes direction when it runs into a mushroom or either the lefi or right boundaries of the playfield.

Page 23

When a centipede is shot, it breaks into two smaller ones, each with a head. Also, the part of the centipede that was shot leaves a mushroom in its place on the screen. When any centipedes reach the bottom of the screen, they start back up, but remain within the area of the player’s shooter (the bottom fifth of the screen).

When a large centipede (that hasn’t been shot yet) reaches the bottom, it releases its tail, and this part changes into a new head. Also to provide player challenge, if a centipede is still alive when it reaches the bottom, new heads will enter the screen almost at the bottom of the sides. More of these heads will appear as time progresses.

The randomly moving spiders also appear in the first wave. The spiders can destroy a player, as well as any mushrooms they move over. This eliminates many mushroom targets for a player.

The player’s shooter is moved by rotating the Mini-Trak Ball™ control. The shooter can be moved in all directions, but only within the bottom fifth of the screen. Pressing the fire button causes the shooter to fire shots upwards, either singly or in rapid-fire mode, if held down constantly. Mushrooms count 1 point when shot, and a player must fire four shots into a mushroom before it is destroyed and disappears. Centipede body parts count 10 points each, and the elusive heads (represented with small eyes on them) are worth 100 points each. Spiders are worth 300, 600 or 900 points, depending on how close they are to the player when shot.

A bombardment of fleas starts in the second wave; as the fleas descend, they leave a trail of new mushrooms behind them.

In the second wave, the fleas appear when a certain number of mushrooms remains at the bottom of the screen. This number increases as the game progresses, meaning fleas appear more often later on in the game.

Fleas have a value of 200 points when shot, and players must hit them twice to destroy them (the first shot just speeds them up).

The scorpion enters from either side starting in the fourth wave; it moves at a relatively slow speed. Later it increases its speed. When shot, a scorpion counts 1000 points—the highest-value target of all.

Page 24

As it travels across the screen, it “poisons” the mushrooms that it moves over and changes their colors. These mushrooms cause any centipedes that would collide with them to head straight towards the bottom of the screen, rather than continue snaking around. Players can stop a poisoned centipede by shooting its head.

in addition, these poisoned mushrooms as well as any partially shot mushrooms add 5 points to the player's score at the end of each life when the screen is resetting.

If the players are very skilled and earn at least 60,000 points, two things happen to increase player challenge: the fleas descend at a faster speed and the spiders restrict their movement to asmaller area at the bottom of the screen. E An important new feature of this game is the operator option for easy/hard game difficulty. In the easy game, the spider moves slowly up to a 5,000-point score, and then bounces at a higher speed. It also changes direction less often throughout the game than at the hard setting.

In the hard setting, the spider moves slowly only for the first 1,000 points, and then speeds up. It also changes direction more often throughout the game. In either setting, the spider always moves at a 45-degree angle or straight up and down.

Another operator option is the number of lives per game, ranging from 2 to 5 (see Figure 7 for switch settings). This number is displayed as small shooters at the top of the screen. The number is decreased by one each time a player is destroyed. The number is increased by one each time the player scores multiples of 10, 12, 15 or 20 thousand points, depending on the operator selection.

  • High Score Initial Mode If a player's score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. At the beginning of this mode, the characters A ______ appear on the screen. The logic will also display the messages GREAT SCORE and ENTER YOUR INITIALS.

Players enter initials one character at a time, choosing from the characters A thru Z and a blank space. Pressing the fire button selects the letter, and rolling the Trak Bali control changes the letters on the screen.

After the fire button is pressed the third time, the initiats and score are transferred to the table. This table contains eight scores and appears during the attract and ready-to-play mode.

All but the highest three scores are erased whenever you enter the self-test, or press the RESET button on the game PCB, or turn off the power. This resetting replaces the lowest five scores with fictitious scores and initials.

If you erase the special “permanent” memory, the high score table is replaced with eight fictitious scores and initials. In other words, the table will always be displayed on the Screen, possibly consisting of one or more realistic scores and players’ initials.

Page 25

Maintenance and Kepair

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the coin box. Just looking at a game will not tell you if Mini-Trak Ball™ control, leaf switch or light-emitting-diode (LED) switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside ot the game and the coin mechanisms. In addition, you will need to regularly lubricate the Mini-Trak Ball control: for details see this chapter.

Page 26

To remove LED switch: NORMALLY CLOSED —. (N.C) CONTACT \ NORMALLY OPEN ————___ ({N.O,) CONTACT LIGHT- EMITTING. | J \ COMMON (L.E.D.) CONTACTS CONTACT

@ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires.

VERT.-MOTION PCB: GREEN, RED, BLACK & YELLOW WIRES.

HORIZ.-MOTION PCB; BLUE, RED, BLACK & VIOLET WIRES

CAUTION Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on ‘the panel, check that the ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.

WHITE

WHTJ/BLK. STRIPE

Figure 10 Opening the Control! Panel and Replacing Switches

A. Cleaning

The exterior of the game cabinet and the metal and glass surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor.

The large monitor shield and the attraction panel are made of tempered glass and should be scratchresistant: if cleaned without abrasive substances, you should hardly ever have to replace them.

B. Fuse Keplacement

This game contains six fuses—all on the power sy)

supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 22 of this manual. See the color monitor manual for the monitor fuse data.

C. The Control Panel

Prior to repairing or replacing any switch or the Mini-Trak Ball™ on the contro! panel, unplug the game. Then open the coin door.

Page 27

Reach through the coin-door opening and open the luggage-style latch, located at each end on the underside of the control panel (see Figure 10). Lift up on the control panel at the topmost edge and tilt it towards you.

The edge of the control panel next to the monitor shield has foam tape applied to it. This tape acts as a cushion for the glass and prevents spilled liquids from entering the cabinet interior. Always make sure this tape is in good condition.

  • LED Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.
  • Remove the wires from ihe suspected switch.
  • Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter.
  • Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts). 4, Check contacts (push and release the switch button) for closed and open continuity.
  • If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
  • Leaf-Switch Replacement

The leaf switch on this game operates on 5 volts at a very low current. Therefore, pitting of the switch would be extremely rare. Probably the only reason that pitting would occur is that the game is in very high-humidity locations. Don’t burnish the switch contacts. Burnishing them removes their plating, thus increasing the corrosion of the contacts. The best method of cleaning the switch contacts is to wipe them with a non-abrasive surface. A business card works very well.

To replace the switch, remove both of its screws with a Phillips-head screwdriver.

If the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The white ring on the outside of the control panel should not spin, due to its design.

NOTE Adjust switch for a narrow gap. Whena switch button is depressed, the resulting wiping action of the contacts provides a self-cleaning feature.
  • Mini-Trak Ball™ Maintenance and Repair

To maintain this control, lubricate the bearings approximately every 3 months or every 6,000 credits. The number of credits can be read off the coin counter, located on the coin door. Use only 2 drops of 3-in-One® oil in each of the ball bearings. (Each Mini-Trak Ball™ control has six bearings.)

For further instructions on how to replace the ball, either coupler PCB or either encoding wheel, see Figure 11.

Page 28

Disassemble in the order indicated. (Circled numbers match the steps described below.)

Bail Replacement

  • First remove the entire Mini-Trak Ball assembly from the control panel as shown in Figure 11. Now locate the six “twinlead” thread-forming screws in the black frames or plastic pieces; remove these six screws.
  • Lift off the top frame; remove and replace the ball.

Coupler PCB and Encoding Wheel Replacement

  • Lift the PCB out of its slot. Carefully unplug the red connector on the coupler PCB.
  • To replace either encoding wheel, remove the PCB from its slot. Remove the socket-head machine screw, flat washer, and split lock washer that secure the encoding wheel. Remove the wheel. When replacing the coupler PCB, be certain that the black metal encoding wheel has not been bent or damaged. it should turn freely between the two halves of the red photosensor device,

LUBRICATE HERE (6 PLACES)

Figure 11 Mini-Trak Ball™ Maintenance and Repair

Page 29

+ To remove the color monitor, follow steps 1 thru 6 D. Monitor below. Refer to the accompanying Figure 12. Kemoval 1. Be sure the game is unplugged from its wail outlet! Unlock and open the rear access panel, coin The following procedure should only be per- door, and control panel. formed by a qualified service technician. 2. Remove the glass monitor shield. Carefully remove the four staples that secure the blue cardboard bezel. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube.

  • Standing at the rear opening of the game, locate the 2-pin and 6-pin harness connectors for the monitor. Unplug both of these.
  • At the bottom rear of the monitor chassis is a wood screw that secures rear part of the chassis. Remove this screw.
  • From the front of the cabinet, locate the flat washers, and self-locking hex nuts (two sets underneath, and two sets above the monitor screen). This hardware attaches the monitor to the cabinet. Remove this hardware.
  • Carefully pull the monitor chassis out of the cabinet towards you.
WARNING Shock Hazard High voltages may exist in any television or monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the yoke area with your hands or with metal objects in your hands! Implosion Hazard lf you drop the monitor and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any monitor.

Disassemble in the order indicated. (Circled numbers match the steps above.)

Figure 12 Monitor Removal

Page 30

E.

Printed-Circuit Board Kemoval

You may wish to remove the Centipede™ game printed circuit board (PCB) or the Regulator/Audio I! PCB for service or inspection. To do this, refer to Figure 13 and proceed as follows:

1. Game PCB Removal Untock and open the rear access panel. Remove the 24-pin and 44-pin edge connectors from the right side of the game PCB. Locate the Phillips-head screw that extends through the PCB and into the two wood blocks (at the right side of the board). Remove and save this screw, as well as the fiber spacers. Remove the PCB from the cabinet by carefully Sliding it straight out of the plastic PCB retainer. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as necessary. After servicing, reinstall the PCB, making sure that the edge connectors are properly plugged in.

Note that the cannectors are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your PCB and will void the warranty. Check that the operation of the game is correct by performing the self-test. \t is especially important to do the self-test with any game when you replace a PCB.

Regulator/Audio If PCB Removal Unlock and open the rear access panel. Remove the five plug-in connectors on the Regulator/Audio Il PCB. Note that all of these connectors are keyed for proper orientation. Locate the two Phillips-head screws that extend through the PCB and into the wood behind the PCB. Remove and save these two screws and the two fiber spacers. Remove the PCB from the interior wall of the cabinet by lifting it up and out of the wood slot.

REGULATOR} AUDIO it PCB

GAME PCB

Figure 13 Printed-Circuit Board Removal

Page 31

Figure 14 Fluorescent Tube Replacement

F. Fluorescent Tube and Speaker

Replacement

WARNING |f you drop a fluorescent tube and it breaks it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube. To replace speaker or the white fluorescent tube behind the front graphics attraction panel, follow this procedure (see Figure 14).
  • Be sure the game in unplugged from its wall outlet. Remove the three Allen-head screws and lock washers at the top of the game (they secure the black metal retainer for the attraction panel). Lift the attraction panel up and out of its lower retainer.
  • If you need to replace the speaker, remove the two Phillips screws that secure the light board to the cabinet, and slide out the whole assembly. The fluorescent light and speaker harness has extra length, so you can pull the assembly about one foot out of the game. Unplug the harness connector just behind the board.
Page 32
  • Remove the two plug-in conneciors on the speaker. Remove the speaker from the wood board and replace it.
  • To replace the fluorescent tube, remove the grey cardboard locking tab at each end of the tube. Slightly rotate the tube up or down, and carefully remove it from the {ampholders.
  • Replace with a new tube. Never force the tube into the lampholders — you may break it, causing an implosion!
  • Also check that the green ground wire is securely attached to the large metal bracket and the ballast transformer behind the wood panel. If the lamp is not grounded, it may not start.
  • If you removed the light and speaker assembly, reconneci the harness connector, then reinstall the assembly. Replace the attraction panel on the front of the game.

G. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for the Centipede™ (upright) game. Sheet 1, Side A, includes a “table of contents” that shows the arrangement of these diagrams. They explain the functions of the circuits; the diagrams also define inputs and outputs.

Atari’s Centipede™ is a microprocessor-controlied game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the contro! panel and coin door. These inputs are processed by the game PCB and output to the monitor, Regulator/Audio Il PCB, loudspeaker, and control panel.

The Regulator/Audio || PCB performs two functions: 1) it regulates the +10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio I! PCB provides most logic power to the game PCB. The audio output from the Regulator/- Audio II PCB directly drives the game speaker and is controlled by the volume control, mounted on the bracket inside the coin door.

The power supply is the source of all voltages in the game. These voltages are protected by three fuses (F3, F4 and F5) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power-sup- Ply chassis.

Figure 15 illustrates the distribution of power in this game. Figure 16 illustrates the distribution of signals. AS

Page 33

FLUORESCENT TUBE

COLOR MONITOR

CONTROL PANEL

COIN DOOR

aN INTERLOCK me.

SWITCHES 44

GAME PCB

LINE VOLTAGE

POWER SUPPLY 115. VAC 6.3VAC

L4 << , AC POWER CORD ‘s > a a

REGULATOR! AUDIO II PCB

POWER ON/OFF ‘SWITCH

Figure 15 Power Distribution

Page 34

SPEAKER

COLOR MONITOR

CONTROL PANEL

a z|2 s| BIE VOLUME CONTROL x 3] ele 3 g] Sl ale 8s) 9/8 Sle 2] 2 2|§ §l3 3|§ zIx edt APS 1) S/El3 ve Els] my =|? 21g o &|8 &/2 of eg fl 3 GAME PCB = e| |8 xa] _[8 Seal z[aja/s | COIN DOOR 8\°

REGULATOR/

AUDIO II PCB

Figure 16 Signal Distribution

Page 35

Illustrated

Parts Lists

This chapter provides you with the necessary information for ordering replacement parts for your Centipede™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “‘A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598-thru approximately 190000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 36

92.049 “a> 03649801 or 92.051 (Upper Retnr.) Fluor. Light & Spkr.— (Monitor) see Figure 23 037411-01 (Attract. Panel) 036495:01 (Spkr. Grille) 003053-01 (Lower Retnr.) 037413-01 (Mon, Shield)

Mini-Trak Ball— 037443-01 (Mon, Bezel) see Figure 19

71-2110 (Lock) Control Panel Assy.— see Figure 18

178013-001 (Latch)

037427-01 (Foam Pad)

19-9032 (ol. Ctrl.) 69-001 (SelFTest Sw.) 03016801 (Bracket) 037419-02 (Rear Panel)

Coin Doors— see Figures 24, 25 036262-01 (Coin Box Brkt.)

036686-01 (Game Pricing Labels— not shown for clarity) A035943-01, -02 or -03 (Coin Box) 035942.01 (Separat 78-3201 (Separator) (Les)

Figure 17 Cabinet-Mounted Assemblies A037397-xx B

Page 37

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe- = — cific written permission of Atari, Inc., Sunnyvale, CA. This Schematics, Self-Test Label & Manuals. drawing s only conditionally issued, ang nelther receipt nor see parts list on following page possession thereof confers or transfers any right in, oF li ‘pense to use, the subject matter of the drawing or any de ‘sign of technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manutacture by vendors of Atari, Inc., and for manufacture under the corporation’s written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation,

'037399-01 (Cab't Assy.)

178034-024 (F-Molding)

A037456-01. (Pwr. Harness)

'035745-02 037443-02 (PCB Retnr.) (Coin Defictr},

034536-03 (A037450-01 (Vibra. Damper) (Interl. Sw./Brkt.)

. Game PCB— 007882-02 = = pa (Interl. Sw. Cvr) see Figure

75-07017 (PCB Spacer)

78-24012 (PCB Tie Wrap)

e ‘ A037433-01 "eo Figure 20 (Main Hares) 034536-02 (Vibra. Damper) A037453-01,

Power Supply Assy.— see Figure 22 037243-01 Plate)

‘A037470-01 (Onl Sw/Mig. Plate) 009992-01 (On/Off Sw. Cvr.)

Figure 17 Cabinet-Mounted Assemblies A037397-xx B

Page 38

Figure 17 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description A035943-01 Deep-Well Coin Box Assembly (for ali the same coins) A035943-02 Deep-Well Coin Box Assembly (for two different coin denominations—has one separator) A035943.03 Deep-Well Coin Box Assembly (for three different coin denominations—has two separators) A037433-01 Main Harness Assembly 5) A037 450-01 Interlock Switch/Bracket Assembly (modified for safety) 5 A037453-01 Strain-Relief Power Cord (U.S.)

A037454-01Strain-Relief Power Cord(Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece,

Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)

A037455-01Strain-Relief Power Cord(Australia and New Zealand)

A037456-01 Power Harness Assembly A037470-01 Power On/Off Switch/Mounting Plate Assembly The following six items are the technical information supplements to this game: DP-182-01 Centipede™ (Upright) Schematic Drawings (Sheet 1) DP-182-02 Centipede Schematic Drawings (Sheet 2) ST-182 Centipede Label with Self-Test Procedure and Option Switch Settings TM-160 \nstruction and Service Manual for 19-Inch Electrohome Color Monitor, or TM-168 Instruction and Service Manual for 19-Inch Wells-Gardner Color Monitor TM-182 Centipede Operation, Maintenance and Service Manual 19-9032 Volume Control

69-001DPDT Self-Test Switch(for British-made coin doors)

71-2110 Panel Cartridge Lock Mechanism (for rear access panel) 75-07017 Spacer for Mounting Printed Circuit Boards 78-24012 5-Inch Beaded Nylon Tie Wrap (for game PCB edge connectors) 78-3201 Cabinet-Leveling Leg 78-6900402 Viny! Foam Single-Coated-Adhesive Tape, %-Inch Thick x %4-Inch Wide (2 x 24 in. req’d.) 92-049 19-Inch Electrohome Color Raster-Scan Monitor, or 92-051 19-Inch Wells-Gardner Color Raster-Scan Monitor 003053-01 Lower Attraction-Panel Retainer 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 030168-01 Volume Control Mounting Bracket (a/so holds self-test switch in games with British-made coin doors)

034536-02Foam Vibration Damper(for Regulator/Audio I! PCB)

034536-03 Foam Vibration Damper (for Centipede game PCB) 035745-02 18-Inch Plastic PCB Retainer 035942-01 Deep-Well Coin Box Separator 036262-01 Coin Box Bracket 036495-01 Speaker Grille 036498-01 Upper Attraction-Panel Retainer 036686-01 Card of Game Pricing Labels 037243-01 Metal Base Plate (located underneath power supply) 037399-01 Cabinet Assembly (includes legs and PCB retainers, but not the rear access panel) 03741 1-01 Attraction Panel with Graphics 037413-01 Monitor Shield with Graphics 037419-02 Rear Access Panel (does not include lock) 037427-01 Rear Access Panel Foam Pad 037443-01 Blue Cardboard Monitor Bezel 037443-02 Cardboard Coin Deflector 178013-001 Spring Draw Latch 178034-024 %4-Inch Black Plastic T-Molding

Page 39

aN

CAUTION Mini“Trak Ball Assy.— 78-6900402 7 '5-9910NO Players may receive an electric shock if see Figure 19 (Foams Tape) giamped Nut) 180013001 this control panel is not properly 6 (Leat Sw. grounded! After servicing any parts on tutton Holder) 178030-001 the panel, check that the ground wire is (Pushbin. Assy.) | firmly attached to the metal tab on the inside of the contro! panel. Only then should you lock up the game.

A037408-01 (Ctrl. Pai) 03312701 (Sw. Bushing)

A037435-01 (Harness)

75-9910W0 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING Stamped Nut) CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA, This drawing isonly conditionally issued, and neither receipt nor Possession thereof confers or transfers any right in, oF license to use, the subject matter of the drawing or any de- 62-039 sign or technical information shown thereon, nor any right 7 eT ee Se ans — NOTE: Graphics decal Is eared ar eanee, mami grariog not field-replaceable. less by written agreement with or written permission from the corporation.

Figure 18 Control Panel Assembly A037409-01 c Parts List

Part No. Description

A037408-01 Control Panel with Graphics A037435-01 Control-Panel Harness 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 75-9910NO #511 Steel Stamped Nut 75-9910W0 #°%,-32 Steel Stamped Nut 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, ¥%-Inch wide x %-Inch thick (24 in. required) 033127-01 Black Molded Switch Bushing 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-001 Pushbutton Assembiy

Page 40

176010-108 —F (6 PLACES) t (Screw)

036193-01

035938-01 (Wheel) ——_]

75.0148 (2 PLACES) 1 (Washer)

75-0445 (2 PLACES) Washer)

72-8406 (2 PLACES) (Screw)

03619201 (Lower Frame)

034168-01 (Label—not shown for clarity) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, 1nc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or translers any right in, or Ik ense to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing of any part thereot. Except for manulacture by vendors of Atari, Inc., and for manufacture Under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereot, uness by written agreement with or written permission from the corporation.

036191-01 (Upper Frame)

035937-01 ee al Bearing)

035931-01 (Roller Shaft)

A036096-01 (Harness)

Figure 19 Mini-Trak Ball™ Assembly A036190-01

Page 41

Figure 19 Mini-Trak Ball™ Assembly Parts List yx)

Part No. Description A035220-01 Coupler PCB Assembly A036096-01 Harness Assembly 72-8406 #4-40 x_%-Inch Hex Socket-Head Cap Alloy Steel Machine Screw 75-0148 #4 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-044S #4 Zinc-Plated Steel Split Lock Washer 034168-01 Label with Lubrication Instructions

035931-01Roller Shafi(2 per assembly)

035936-01 Mini-Trak Bali™

035937-01Ball Bearing(6 per assembly)

035938-01 €tched Encoding Wheel 036191-01 Upper Black Plastic Frame 036192-01 Lower Black Plastic Frame

036193-01idler Shaft(1 per assembly)

176010-106 #8 x %;Inch Cross-Recessed Pan-Head Thread-Forming Twin-Lead Zinc-Plated Steel Screw

Page 42

receipt nor

Possession thereof confers or transfers any right Inyo

‘cense to use, the subject matter of the drawing or any desi or technical information shown thereon, Nor any right

to reproduce this draw

under the corporation's written

to reproduce this drawing or the

Jess by written agreement with or written permission from

the corporation.

5.6K

TIP 32

A035435-02 R212

Figure 20 Regulator/Audio Il PCB Assembly E TE Rizo 7812 el)

Rid TOAZ002 A

2. +

jos ° > A R24, 10, 7

o cle FaD cise) R22 9p 7905

art TOA20024

cl4 fe)

S

220 | R2!, ew Cc bal

+

p32 tt cig 3300 35V

3300 35V

R25, 4.0, 5W C225 c23

Sra Q te} c3i Seep

e22z} cr) R3I

  • 220,10w -— ro}
Page 43

Figure 20 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

12-52P72.7 Ohm, +5%, iW Resistor(R5)
16-54P04 Ohm, +5%, SW Wirewound Resistor(R25)
19-100P10151 Ohm, +3%, 7W Wirewound Resistor(R24)
49-3151021K Ohm Vertical PCB-Mounting Cermet Trimpot(R8)
24-2501081000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13)
24-250477470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C1, 4, 12)
24-35022622 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor(C24, 31)
24-350338.3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor(C9, 10, 18, 19)
24-5001051 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C22, 23)
29-088.1 uf Ceramic-Disc 25V Radial-Lead Capacitor(C3, 11, 20, 21)
31-1N4002100V 1-Amp. Silicon Rectifier Type 1N4002 Diode(CRI, 4)
31-1N5401100V 3-Amp. Silicon Rectifier Type 1N5401 Diode(CR5-8)
33-TIP32PNP Power Transistor, Type TIP32(Q2)
34-2N3055,NPN Silicon Transistor, Type 2N3055(Q3)

37-LM305 5V Linear Voltage Regulator (Q1)

37-7812+12V Voltage Regulator, Type 7812(Q8)
37-7905—5V Voltage Regulator, Type 7905(Q9)

72-1608C #6-32 x ¥-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 72-6606S #6 x %-Inch Pan-Head Thread-Forming Cross-Recessed Type-AB Zinc-Plated-Steel Screw (Q8)

75-F60405#6-32 x %4-Inch Binder-Head Nylon Screw(Q5, 7)

75-99516 #6-32 Nut/Washer Assembly

78-16008Thermally Conductive Compound(Q3)
78-16014Thermally Conductive Silicon Insulator(Q2, 9)

79-58306 6-Position Connector Receptacle (J6, 9)

79-583089-Position Connector Receptacle(7)
79-5834612-Position Connector Receptacle(J10)
79-583544-Position Connector Receptacle(J8)

020670-01 Test Point 034531-01 Heat Sink

100015-103.01 uf Ceramic-Disc 25V Radial-Lead Capacitor(C5, C14)
110000-0101 Ohm, +5%, %4W Resistor(R10, 19)
110000-10010 Ohm, +5%, %W Resistor(Rt1, 20, 29, 30)
110000-101100 Ohm, +5%, %4W Resistor(R4, 12, 22)
110000-1021K Ohm, +5%, %4W Resistor(R27, 28)

110000-103 10K Ohm, +5%, %W Resistor (R13, 14)

110000-271270 Ohm, +5%, YW Resistor(R1)

110000-330 33 Ohm, +5%, %W Resistor (R3) 110000-392 3.9K Ohm, +5%, 14W Resistor (R6)

110000-5625.6K Ohm, +5%, %W Resistor(R32, 33)
110000-7527.5K Ohm, +5%, %4W Resistor(R7)
110001-221220 Ohm, +5%, Y2W Resistor(R9, 21)
116000-22022 Ohm, +5%, 10W Wirewound Resistor(R31)
122002-102.001 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor(C2, 7, 16)
122004-224.22 uf Ceramic-Disc 25V Capacitor(C6, 8, 15, 17)
137151-002Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit(Q5, 7)
Page 44
Scan of page 44

This page is a drawing, shown as the original scan.

Page 45

Figure 21 Centipede™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) C012294-01 Audio 1/0 N-Channel MOSI/LSI Custom Chip (C3) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C83) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C52, 78) 24-500105 1 mf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C79-82, 84, 86) 24-500106 10 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C85) 29-088, +1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 5-37, 40-51, 54-64, 66-77, 87, 88)

31-1N91475V Type-1N914 Switching Diode(CR1, 2)
31-1N400175V Type-1N4001 Switching Diode(CR4, 5)

33-2N3906 Type-2N3906 PNP Switching and Amplifying Transistor (Q3) 34-2N3904 Type-2N3904 NPN Silicon Transistor (Q1, 2, 4, 5) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q6-8)

37-LM324Type-LM324 Integrated Circuit(J10)
37-4584BType-4584B Integrated Circuit(F10, F11)
37-555Type-555 Timer Integrated Circuit(A11)

37-74LS00 Type-74LSO00 Integrated Circuit (L8) 37-74LS04 Type-74LS04 Integrated Circuit (K3)

37-74LS08Type-74LS08 Integrated Circuit(B7, K4)
37-74LS10Type-74LS10 Integrated Circuit(L3, K2)
37-74LS20Type-74LS20 Integrated Circuit(A7)
37-74LS32Type-74LS32 Integrated Circuit(A4, C5, E3, F3, J3)
37-74LS42Type-74LS42 Integrated Circuit(H3)
37-74LS74Type-74LS74 Integrated Circuit(D4, D11, M3)

37-74LS83 Type-74LS83 Integrated Circuit \ (F6, H6)

37-74LS86Type-74LS86 Integrated Circuit(E7)
37-74LS90Type-74LS90 Integrated Circuit(L2)
37-74LS139Type-74LS139 Integrated Circuit(C4, J2)
37-74LS153Type-74LS153 Integrated Circuit(C7, E8, K6, L6, M6, N6, P6)
37-74LS157Type-74LS157 Integrated Circuit(D7, D8, E11, F8, H8, J8, K8, P5)
37-74LS163AType-74LS163A Integrated Circuit(A5, B5, M2, N2, N3, P2, P3)
37-74LS166Type-74LS166 Integrated Circuit(H9, J9)
37-74LS174Type-74LS174 Integrated Circuit(C6, D6, E6, J4)
37-74LS175Type-74LS175 Integrated Circuit(A8, E4, M4, N4)
37-74LS191Type-74LS191 Integrated Circuit(B11, C11)
37-74LS244Type-74LS244 Integrated Circuit(B1, C1, H5)
37-74LS245Type-74LS245 Integrated Circuit(E2)
37-74LS257Type-74LS257 Integrated Circuit(D9, E10, K9, L9, P7, M8, M9)
37-74LS259Type-74LS259 Integrated Circuit(M10)
37-74LS273Type-74LS273 Integrated Circuit(B4, J6)
37-74LS373Type-74LS373 Integrated Circuit(J5)
37-74LS374Type-74LS374 Integrated Circuit(H4)
37-74804Type-74S04 Integrated Circuit(N1)
37-74S874Type-74S74 Integrated Circuit(E9, F9)
37-7407Type-7407 integrated Circuit(A9, A/B10)

37-7815 + 15V Voltage Regulator (VR2) 37-7915, -15V Voltage Regulator (VR1)

38-MV5053Type-MV5053 Light-Emitting Diode(CR3)

[Continued on next page]

Page 46

Figure 21 Centipede™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 41-3003 100 uH, +5%, Hot-Molded Plastic Fixed R.F. Choke (L1-3) 62-001 SPST Momentary Pushbutton Switch (Reset) 66-114P1T 4-Station, Single-Throw, Dual-Inline-Package Bit Switch (N11) 66-118P1T 8-Station, Single-Throw, Dual-Inline-Package Bit Switch (N8, N9)

79-42C1616-Contact Medium-Insertion-Force Integrated Circuit Socket(P4)
79-42C2222-Contact Medium-Insertion-Force integrated Circuit Socket(E5)
79-42C2424-Contact Medium-Insertion-Force Integrated Circuit Socket(F7, H/J7, D1, E1, F/H1, J1)
79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(C2, C3)

81-4302 Nylon Snap-In Fastener

90-10212.096, + .005%, Crystal(¥1)

90-6013 Microprocessor (C2)

90-7005Random-Access Memory(C8)
90-7018Random-Access Memory(K5, K7, L5, L7, M5, M7, N5, N7)

90-7033 Random-Access Memory (F2, H2) 020670-01 Test Point 110000-102 1K Ohm, +5%, YW Resistor (R9-11, 13-16, 23-28, 31-38, 55-60, 67, 68, 77, 79, 80, 87-89, 94, 95, 99, 104, 109, 114-123, 134, 136-141) 110000-103 10K Ohm, +5%, 4W Resistor (R1, 2, 6-8, 12, 17-22, 29, 30, 39-54, 70, 71) 110000-104 110K Ohm, +5%, %4W Resistor (R81, 82, 105, 106) 110000-105 100 MegOhm, +5%, %W Resistor (RS5) 110000-152 1.5K Ohm, +5%, %W Resistor (R108) 110000-221 220 Ohm, +5%, %4W Resistor (R3, 62, 64, 66, 72, 74-76, 78, 135) 110000-222 2.2K Ohm, +5%, %W Resistor (R107) 110000-331 330 Ohm, +5%, %4W Resistor (R61, 63, 65, 73) 110000-332 3.3K Ohm, +5%, YW Resistor (R69, 83-86, 103, 130-133) 110000-471 470 Ohm, +5%, YW Resistor (R90-93, 96-98, 100, 110-113, 124-129, 142) 110000-560 56 Ohm, +5%, v4W Resistor (R101, 102) 110000-563 56K Ohm, +5%, %4W Resistor (R4) 122002-102 .001 uf Ceramic-Disc 50V Radial-Lead Capacitor (C4) 122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C65) 122005-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C53) 128002-101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C1) 128002-221 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C38, 39) 128002-390 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C2)

136001-201 or -211Read-Only Memory(F7)
136001-202 or -212Read-Only Memory(H/J7)
136001-203 or -207Read-Only Memory(D1)
136001-204 or -208Read-Only Memory(E1)
136001-205 or -209Read-Only Memory(F/H1)
136001-206 or -210Read-Only Memory(J1)

an 136001-213 137161-001

137169-001 137170-001 Programmable Read-Only Memory (P4) Type-ER2055 Integrated Circuit (E5) Note: /f you replace this part, you must erase this ROM before locking up the game. See Figure 6, Self-Test Procedure, in this manual for instructions. Type-74LS107 Integrated Circuit (L4) Random-Access Memory (A6, B6) Acceptable substitute is part no. 90-7008 or 90-7035.

Page 47

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 48

79-4411001 (Fuse Post) 03448202 037639-01 46-2017002

0345440146-2014002037641-01
a(Chassis)(Label)(Fuse)Cover)(Fuses)yest

——_- 79-3206 r 1 (Fuse Block)

‘A035891-01 (Fuse Harness)

78-2708 (Hole Bushing) TOP VIEW

73:705018C USTEENTIAL Reproduction forbdcn without te spe- RPDENTIAL: Reproduction foidden without the

03767103 has the 220Vand 240plugs3Botee fo use, tre subject matter ofthe Crewing Or any dex

al = Plugs (Capacitor) Sign or technical information shown thereon, nor any ight igh to reproduce this drawing or any part thereof. Except for ‘manufacture by vendors of Atari, Inc., and for manufacture Under the corporation's writen licenée, no right is granted

to reproduce this drawingor the subject matterthereof, un-

A035888-01 less by written agreement with or written permission from (Transformer) ‘the corporation.

BOTTOM VIEW

3A-MDA3501 (Rectifier)

A034630-01A035890-01A034629-017915021001
(RFI Filter)(Pwr. Harness)(AC. Harness)(Term! Block)

Figure 22 Power Supply Assembly A037671-xx B

Page 49

Figure 22 Power Supply Assembly ASS Parts List

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100V(violet)
A021084-02Voltage Plug for 120V(yellow)
A021084-04Voltage Plug for 220V(blue)
A021084-05Voltage Plug for 240V(brown)

A034629-01 A.C. Harness Assembly

A034630-01RFI Filter Assembly(FL1)
A035888-01Transformer Assembly(T1) Acceptable substitute is part no. A035888-02

A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly 29-053 27,000 uf 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)

46-20140024-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30120320-Amp. 32 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x ‘%,-Inch Outside Diameter x V-Inch Thick 78-70501SC. 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 03454401 Fuse Block Cover

037639-01Label for Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)
Page 50

Gentipede™

a

NOTE To ensure that the fluorescent tube starts, make sure the ground wire is firmly attached to both the ballast transformer and the steel lamp bracket. 99-1103 99-1109 79.561816P Gtarter) Gocket) 148001-001 (Wire Nut) (Speaker) ‘A037457-01 (Harness)

179035-001 (Lampholder) 142028-xxx / (Transformer) '037469-01 70-304 (Tube) (Bracket) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for A037540-01 manufacture by vendors of Atari, Inc., and for manufacture 99-1106" No Grd. Wire) tSeprodue fe drawing rte sublect matter eso une (Tab) less by written agreement with or written permission from the corporation.

Figure 23 Fluorescent Light and Speaker Assembly A037417-01 and -02 D

Parts List

Part No. Description A037457-01 Light and Speaker Hamess A037540-01 Ground Wire with Ring Lug 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 79-561816P Spring-Connector Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter 99-11006 Fluorescent Lamp Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037469-01 Steel Lamp Bracket 142028-001 60-Hz 118-Volt Ballast Transformer (used on A037417-01 assembly) 142028-002 50-Hz 118-Volt Ballast Transformer (used on A037417-02 assembly) 148001-001 6x9Inch 4-Ohm 15Watt Oval High-Fidelity Speaker 179035-001 2-Pin Fluorescent Lampholder

Page 51

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 52

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-10103 CONFIDENTIAL: Reproduction forbidden without the (inner Phi specific writen permission of Atari, Inc, Sunnyvale, CA, This drawing is only conditionally issued, and neither wiLevers) 75-948S eceipt nor possession thereof conters or ‘transfers any right in, or license to use, the subject matter of the drawing 99-10096 of any design or technical information shown thereon, nor (Fastener) any right to reproduce this drawing or any part thereof. Except Tor manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof uniess by written agreement with or written permission from the corporation, 99-10071 (Slam Sw

75-1408S (Screw) NN ) 99-10095 (Self-Test Sw.) 99-10052 (Lever) a

Y x (Hex Nut)

75-9448 99-10096 (Hex Nut) (Fastener)

98-10063 (Coin Chute) 99-10040 99-1097 (Coin Inlet Chute) | 99-10101 (insul.) (Coin Chute)

70-11-47 (Lamp),

99-10080 (Lamp Socket)

72-9406S. (Screw)

< > 99-10104 wae (Bar Retnr.)

99-10041 (Coin Counter)

99-10081 (Key Holder) (Coin Mech.)

75.9448 (Brkt. Assy.) 65-4416 roscoe.

99-10065(Coin Sw)‘
COIN RETURNeuiaeen«(Screw)
99-106899-10075 than99-10047

(Coin Chute) 99-1078 S (Lockt, Coil) (Sw. Wire) 31-1N4002—Part baeen thru 99-10008 of 99-10047 9910045 . Sc (Coin Sw. Assy.) (Retainer) 7814128 99-10082 (Plode) (Screw) (Cover) Figure 24 American-Made Coin Door 71-10XXXX D

Page 53

99-10012 thru 99-1022, and 98-10107 (Bution Assy.)

99-10062 (Button)

99-10009 or 99-10010 (Door)

99-10094 (Insult) L

Part of 99-10074

99-10049 (Locking Arm)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the cific written permission of Atafi, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, of lr Cense to use, the subject matter of the drawing or any design of technical information shown thereon, nor any right to reproduce this drawing or any part thereol. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

71-102201 — U.S, 25%/25¢ Coin Door 71-103202 — U.S. 259/25¢/25¢ Coin Door 7%-103203 — U.S. 25¢/25¢/$1 Coin Door 71-402204 —- German 2 DM/1 DM Coin Door 71103205 — German 1/2/5 DM Coin Door pS = 99-10055 thru 99-10059 (Button Cover)

99-10074 (Lock) 99-10070, 99-10083 thru 99-10092, and 99-10108 (Price Plate)

75.9188 (Hex Nut)

75-9158 (Hex Nut)

'99-10051 (Frame)

71-102206 — German 1 DM/5 OM Coin Door 71-102207 — Belgian 5 Fri5 Fr Coin Door 71-102208 — Swiss 4 Frit Fr Coin Door 71-102209 — Japanese 100Y/100Y Coin Door 71-102210 — British 10 P/10 P Coin Door 72-JA1405B (Screw) 99-1054 (Btn. Housing) 72-HA1404C (Screw)

eC cnere arent

99-10061 (Bezel)

99-1006 (Cover)

72-JA1405B (Screw)

99-10048 (Harness—not shown for clarity)

74102211 — Australian 20°/20¢ Coin Door 71-102212 — Italian 100 L/100 L Coin Door 71102213 — U.S. 500/506 (2 x 25¢) Coin Door 71-103214 — U.S. 50/50%/50¢ Coin Door 71-103215 — U.S, 500/50¢/$1 Coin Door

Figure 24 American-Made Coin Door 71-10Xxxx D

Page 54

Figure 24 American-Made Coin Door, continued Parts List

Part No. Description 31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-4416 General-Usage Low-Force Miniature Switch 70-11-47 Miniature Bayonet-Base Incandescent Lamp, Type #47 71-1201ADU U.S. $1.00 Coin Mechanism 71-1201FCH Swiss 1 Fr Coin Mechanism

71-1201MG German 1 DM Coin Mechanism 71-1202MG German 2 DM Coin Mechanism 71-1205FB Belgian 5 Fr Coin Mechanism 71-1205MG German 5 DM Coin Mechanism 71-1210PE U.K. 10 P Coin Mechanism 71-1220CA Australian 20¢ Coin Mechanism 71-1225CU U.S. 25¢ Coin Mechanism 71-12100LI Italian 100 Lire Coin Mechanism 71-12100YJ Japanese Y100 Coin Mechanism 72-HA1404C #4 x ¥4-Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Taptite” Cadmium-Plated Screw 72-JA1405B #4 x %{,Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Plastite” Black Screw 72-9406S #4-40 x %-Inch Slotted Truss-Head Steel Machine Screw 72-9603S, #6-32 x ¥-Inch Slotted Truss-Head Steel Machine Screw 75-915S #%4-20 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-918S #8-32 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-944S #4-40 Polymer Self-Locking Steel Hex Nut 75-948S #8-32 Polymer Self-Locking Steel Hex Nut 75-1408S #4-40 x ¥2-Inch Slotted Pan-Head Steel Machine Screw 75-1412S #4-40 x 34-Inch Slotted Pan-Head Steel Machine Screw 75-5520B #%-20 x 1¥%-Inch Round-Head Square-Neck Steel Bolt with Black Finish 99-10008 Switch Wire Retainer 99-10009 2-Mech Coin Door Only 99-10010 3-Mech Coin Door Only 99-10012 U.S. 25¢ Coin Return Button Assembly 99-10013 U.S. $1.00 Coin Return Button Assembly 99-10014 German 1 DM Coin Return Button Assembly 99-10015, German 2 DM Coin Return Button Assembly 99-10016 German 5 DM Coin Return Button Assembly 99-10017 Belgian 5 Fr Coin Return Button Assembly 99-10018 Swiss 1 Fr Coin Return Button Assembly 99-10019 Japanese Y100 Coin Return Button Assembly 99-10020 U.K. 10 P Coin Return Button Assembly 99-10021 Australian 20¢ Coin Return Button Assembly 99-10022 Italian 100 Lire Coin Return Button Assembly 99-10040 Coin Inlet Chute Assembly 99-10041 Coin Counter Assembly 99-10042 Coin Switch Assembly for U.S. 25¢ and Belgian 5 Fr Coins (silver wire)

99-10043Coin Switch Assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 Coins(black wire)
99-10044Coin Switch Assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins(go/d wire)
99-10045Coin Switch Assembly for German 5 DM, U.K. 10 P, and Australian 20¢ Coins(green wire)

99-10047 Lockout Coin Assembly 99-10048 Coin Door Harness Assembly

Page 55

Figure 24 American-Made Coin Door, continued Parts List

Part No. Description 99-10049 Locking Arm Assembly 99-10051 Coin Door Frame 99-10052 Coin Return Lever 99-10054 Coin Button Housing 99-10055 Coin Return Button Cover for Japanese 100Y Coin 99-10056 Coin Return Button Cover for German 1 DM and Swiss 1 Fr Coins 99-10057 Coin Return Button Cover for U.S. 25¢ and Belgian 5 Fr Coins 99-10058 Coin Return Button Cover for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins 99-10059 Coin Return Button Cover for German 5 DM, U.K. 10 P, and Australian 20¢ Coins 99-10061 Coin Return Bezel 99-10062 Coin Return Button 99-10063 Right Half of Coin Inlet Chute 99-10065 Coin Return Box 99-10066 Coin Return Cover 99-10068 Coin Chute 99-10070 U.S. 25¢ Price Plate 99-10071 Slam Switch Assembly 99-10073 Test Switch Decal 99-10074 Lock Assembly 99-10075 Black Switch Wire for German 1 DM, Swiss 1 Fr and Japanese 100Y Coins 99-10076 Silver Switch Wire for U.S, 25¢ and Belgian 5 Fr Coins 99-10077 Gold Switch Wire for U.S, $1.00, German 2 DM and Italian 100 Lire Coins 99-10078 Green Switch Wire for German 5 DM, U.K. 10 P and Australian 20¢ Coins 99-10080 Miniature Bayonet-Base Lamp Socket 99-10081 Wire Key Holder 99-10082 Switch Cover 99-10083 U.S. $1.00 Price Plate 99-10084 German 1 DM Price Plate 99-10085 German 2 DM Price Plate 99-10086 German 5 DM Price Plate 99-10087 Belgian 5 Fr Price Plate 99-10088 Swiss 1 Fr Price Plate 99-10089 Japanese Y100 Price Plate 99-10090 U.K. 10 P Price Plate 99-10091 Australian 20¢ Price Plate 99-10092 Italian 100 Lire Price Plate 99-10094 Fish Paper Insulation 99-10095 Toggle Switch 99-10096 “U”-Type Fastener 99-10097 Fish Paper Insulation 99-10101 Left Half of Coin Inlet Chute 99-10102 Switch and Lockout Coil Bracket Sub-Assembly 99-10103 Inner Panel with Levers Sub-Assembly 99-10104 Anti-Penny-Flip Bar Retainer 99-10105 Anti-Penny-Flip Bar 99-10107 U.S. 50¢ Coin Return Button Assembly (for two quarters) 99-10108 U.S. 50¢ Price Plate (for two quarters)

Page 56

99-15038 (Bezel for Button)

99-15001 thru 99-15012 (Ret. Button) a ZO Y

99-15052\Zo4
(Spring for Button)4a

\ 4

99-15051 (Lamp Holder)

9915040 LC (Lever) - 99-15056 (Screw for Bezel) Pr J

Goin nie O _80'5030

2]Z\(Bezel for Cover)

PART OF 99-15036 99-15041 ‘ones 99-15055 Ki a 99-15054 \ 99-15041 - (Pivot for Lever) (Retng. Screw) > (Lockout Coil) .

Yor{99-15053es

(Lockt. Cot Spring) <<” 9.15027 (Coin Ret. Box)

99-15037 (Sw. Adjusten 99-15056 (Sctew for Bezel 99-15060 Gace OO Cover) seso42-—~ ¢ (Switch)

Figure 25 British-Made Coin Door 171001-xxx A

Page 57

99-15067 (Lock Assy.)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This. drawing is only conditionally issued, and neither receipt nor Possession thereof confers or transfers any right in, oF li- Gense to use, the subject matter of the drawing or any de sign of technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.

99-15064 (Frame)

171001.001 — British 10 P/10 P Coin Door 171001-002 — British 10 P/50 P Coin Door 171001-003 — British 20 P/50 P Coin Door 171001004 — German 1 DM/1 DM Coin Door 171001.005 — German 2 DMH DM Coin Door 47-1002 (Counter)

171001.006 — German 2 DM/S5 DM Coin Door 171001.007 — Belgian 5 Fri5 Fr Coin Door 171001.008 — French 1 Fri1 Fr Coin Door 171001.009 — French 2 Fri1 Fr Coin Door 171001-010 — Swedish 1 Kr/1 Kr Coin Door 99-15067 (Lock Assy.)

99-15062 (Hinge)

B B ¥

99-15066 (Screw) 99-15065 (Clamp)

171001-011 — Hong Kong $1/$1 Coin Door 171001-012 — Canadian 25¢/25¢ Coin Door 171001-013 — U.S. 25¢/25¢ Coin Door 171001-014 — Spanish 25 Pts/25 Pts Coin Door 171001-015 — Swiss 1 Frit Fr Coin Door

Figure 25 _British-Made Coin Door 171001-xxx A

Page 58

Figure 25 _British-Made Coin Door, continued 171001-xxx A

Part No. Description 47-4002 Coin Counter 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Retum Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25%) Price Plate 99-15025 Left Half of Coin inlet 99-15026 Right Half of Coin inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-1504 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055. Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15061 Dual-Entry Door 99-15062 Hinge 99-15063 Screw for Hinge 99-15064 Coin Door Frame 99-15065 Clamp for Frame 99-15066 Screw for Frame 99-15067 Lock Assembly

Page 59

YOUR COMMENTS, PLEASE! amines

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm O Distriputor

Address. OC Operator City State Zip U Other.

Area Code Phone

Page 60

First fold

i

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086

Second fold No Postage Necessary if mailed in the United States

swo1

Page 61

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability Shall be, at its aption, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged detects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order. = (a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective;

V diee Nabi alee Nia, Satie Nated, Sated Nate Ss The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may seil parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 64

A.

ATARI

ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 ¢ TELEX 35-7488

] > Waive: Communications Company