CATHODE RAY TOMES

Gravitar TM-206 1st Printing

Gravitar (version 3) (Atari, 1982) · Technical Manual · 52 pages · 44 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

BER TE 2 4 We iif ie

Page 3

i ri) qi) yan

Operation, Maintenance

and Service Manual

Complete with Illustrated Parts Lists

Page 4

© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitied, or otherwise copied for public or private use, without permission from the publisher.

The Gravitar™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the new Copyright Act of 1976.

This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles,

In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys' fees, fines up to $25,000, and face an imprisonment of up to one year.

Atari wiil aggressively enforce its copyrights against any infringers. We will use ail legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anycne who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Lithographed in the U.S.A. 7k

Page 5

Notice Regarding Non-ATARI Parts

WARNING Use of non-ATARI paris or modifications of your ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

The warranty printed on the inside back cover of this manual may be voided, if you do any of the following: @ Substitute non-ATARI parts in your coin-operated game, or @ Modify or alter any circuits in your ATARI game by using kits or parts not supplied by Atari. The use of any non-ATARI parts will void the warranty, and any such alteration may also adversely affect the safety of the game and may cause injury to you and your players.

1 riiwit N N 4! ‘MS Ta (} = g= (5) la J \ } i S EI S re SS

If you suspect interference from an ATARI game at your location, check the folto licensed communications services is not permitted by the FCC (Federal Communications Commission).

lowing: @ All grounds (green wires) in the game are properly connected as shown in the game wiring diagram, and @ The power cord is properly plugged into a grounded 3-wire outlet. lf you are unable to solve the interference problem, please contact ATARI Customer Service. See page vi for service in your area.

Page 6

Table of Contents

1 SetUp Procedures New Features ...... 00. e cece cece erence eee ene nee een eee 1-3 a Game Inspection . 1-3 C. Game Installation... 1-3

  • Installation Requirements ......... ccs c cece eee eee eee 1-3
  • Voltage Selection ..... -. 13 D. Switch Locations... 1-4
  • On/Off Switch ..... 1-4
  • Utility Panel Switches 1-4
  • Option Switches .... 1-4 E. Option Switch Settings . 15 F. Self-Test Procedure . 1-7 G. Game Play . 19
  • Demonstration Mode 5
  • AttractMode......
  • PlayMode ....
  • High-Score Mode ..
  • Hints for Game Play

2 Troubleshooting A. Comments on Troubleshooting. ............-.00. cece e eee eee 2-2 B. Self-Test Procedure ........... 0c c cece cece cee e eens 22

3 Maintenance, Repair and Parts A. Cabinet-Mounted Assemblies 3-2 B. TheControl Panel ......... 3-4 C. Fluorescent Tube and Speaker . - 36 D. Video Display........... 38 E. Coin Door .. 3-10 F. Printed-Circuit Boards . 3-13 G. Power Supply Assembly ...........0 00.00 ccc eee eee eee eae 3-21

Page 7

Figure 1-1 Figure 1-2 Figure 1-3 Figure 2-1

Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5

Figure 2-6 Figure 2-7 Figure 2-8

Figure 3-1 Figure 3-2 Figure 3-3

Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7

Figure 3-8 Figure 3-9 Figure 3-10

Table 1-1 Table 1-2 Table 1-3 Table 1-4

Table 1-5 Table 1-6 Game Overview Game Switch Locations ... Operator Information Display . Self-Test Screen 1—Test Passes . . List of Illustrations

Self-Test Screen 1—Test FailS..........0 0.00 cece cece scence eee 2-3 Self-Test Screen2 ... 2-3 Self-Test Screen3 . » 2-4 Self-Test Screen 4 22.0... cece ccc e eee eee n ete nets 2-4

Self-Test Screen 5 2-4 Self-Test Screen 6 2-4 Screen 7: Self-Test Screens During Signature Analysis 2-5

Maintenance, Repair and Parts: Cabinet-Mounted Assemblies Control Panel ..........6. ec eee eee eee Control Panel Assembly ........0.. 000 e cee eee e eee eee eee 3-5

Fluorescent Tube and Speaker a. 3-6 Video Display...............0.05 ... 38 Vertically Mounted Coin Door........ 2.2310 Printed-Circuit Board (PCB) Removal 23-13

Gravitar Game PCB Assembly .... 11 O14 Regulator/Audio I! PCB Assembly . - 3-19 Power Supply Assembly 3-21

Game Price Options Special Options Game Play Options . Self-Test Procedure ............scsscsscsssesseceserereeees

Gravitar High-Score Lists .. 0.0.0.0... 0.2.0 cece ee eee eens 1-9 Gravitar Scoring

Page 8

vi |f reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Facific Time) exe From California, Alaska, or Hawaii oO @@ (408) 745-2900 exe Service from anywhere in the area shown in white toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World’s Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday~Friday, 7:30-4:00 pm Eastern time) em From New Jersey (201) 469-5993 O From anywhere else in this area @@ toll-free (800) 526-3849

EUROPE

Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

BZ 06252155

Page 9

Set-Up Procedures

How to Use This Manual

This manual, written for game operators and service technicians, describes the Gravitar™ game. Chapter 1 describes new features, game setup, option switch settings, self-test procedures, and game play. Chapter 2 contains troubleshooting procedures. Chapter 3 details maintenance, repair, and parts information. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.

Chapter

Page 10

Set-Up Procedures

ATTRACTION PANEL See Figures 31 & 3-4 FLUORESCENT TUBE

AND SPEAKER See Figure 3-4

VIDEO DISPLAY See Figure 3-5

CONTROL PANEL See Figures 32 & 33

SPEAKER

COIN DOOR See Figure 3-6

UTILITY PANEL See Figure 1-2

let, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

Figure 1-1 Game Overview Gravitar™

GAME PCB See Figures 3-7 & 38

REGULATOR! AUDIO I! PCB See Figures 3-7 & 3.9

POWER SUPPLY POWER ON/OFF SWITCH Fi 3-10 SHOCK HAZARD See Figure

Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire out-

Page 11

Gravitar™

A. New Features

The Gravitar™ game has four new features. Even if you are familiar with ATARI® games, you should

note these important differences:
  • Shielded Game Speakers. These 8-ohm, 6-ounce, high-fidelity speakers provide exceptional audio. The speaker magnets are shielded.
  • Key Loops. The utility panel has two key loops. They provide a convenient place to store keys for the rear access panel and lower coin door.
  • High-Score Table. There are eight different titles for the high-score table. The title is determined by the highest score registered (see G. Game Play).
  • Molded Coin Box. This game has a sleek, onepiece molded coin box with handles on either end for easier carrying. New features and all other major parts in the game are illustrated in Figure 1-1. Throughout this manual, wherever one of these new features is mentioned, you will see this symbol:

B. Game Inspection

Please inspect your game carefully to ensure that it was delivered to you in good condition.

NOTE Do not plug in the game yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts. 2, Remove the screws that were used as exira security to seal the rear access panel. Uniock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harness) are firmly plugged in. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. b. Ensure that all plug-in integrated circuits on the PCB are firmly piugged into their sockets. c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the ‘Set-Up Procedures

power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening.

To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!

d. Note the game serial number. It is printed on a label on the back of the cabinet. Verify that the same serial number is also on the Gravitar game PCB, Regulator/Audio {| PCB, power supply, and video display. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. e. Inspect major subassemblies, such as the power supply, control panel, and video dis- Play, for secure mounting.

C. Game Installation

  • Installation Requirements

Power 200 W Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 64 x 80 cm (25 ¥2 x 31%? in.) Game Height 184 cm (72 V2 in.)

  • Voltage Selection The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three different voltage selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). Before plugging in your game, check your line voltage. Then check the wire color on the voltage selection plug that is piugged into your power supply. Make sure the voltage selection plug is correct for your location's line voltage (see Figure 3-10).

1-3

Page 12

Set-Up Procedures Gravitar™

D. Switch Locations

  • On/Off Switch vates the left coin counter. These ewliches are lo- The on/off switch is located on the back of the cated inside the upper coin door (see Figure 12).

cabinet, lower left side (see Figure 1-2). 3. Option Switches

ae . Option switches are located on the game PCB

  • Utility Panel Switches (see Figure 1-2). The utility panel includes the volume control, self- a. Game price options are at PCB location B4. test switch, coin switch, and coin counter(s). The b. Game play options are at PCB location D4. coin switch is used to credit the game, and it acti- ¢. Special options are at PCB location P10/11.

UTILITY PANEL OPTION SWITCHES

Pio @ at OFF 8-1 og ae oN at

COIN COUNTER

d SWITCH AT B4 KEY LOOP / (Game Price) p— SWITCH AT D4 (Game Play) SWITCH AT P10/11 (To increase, nr cbeianee) POWER ON/OFF SWITCH Spontal Options) SELF-TEST SWITCH

VOLUME CONTROL

Figure 1-2 Game Switch Locations

Page 13

Gravitar™

E. Option Switch Settings

Tables 1-1, 1-2, and 1-3 detail game option switch settings. Options are preset at the factory and shown by the < symbols. However, you may change the settings to suit your individual needs.

Table 1-1

This table contains the switch settings for options relating to game price, coin mechanism multipliers, and bonus play. The ‘switches are on the game PCB at location B4 and are accessible when the game PCB is mounted in place.

The coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. After this inspection, the mechanism either accepts or rejects the coin.

The muitipliers (toggles 4-6) determine how much each coin mechanism will be worth to the game's logic. The coin door has two mechanisms. Set-Up Procedures

To verify option switch settings, power the game off and then on again. Set the self-test switch to on and verify the settings on the self-test screen. Then set the self-test switch to off.

Game Price Options

The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. Therefore, if you have a2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1.

You may offer bonus play for certain combinations of coins inserted. For example, with the game set at $.25 per play, players who deposit four successive quarters, then press the start switch, can receive a bonus play. The bonus feature encourages players to insert more money than just the minimum $.25 required for one game. All coins must be inserted before pressing the start switch.

Settings of 8-Toggle Switch on Gravitar PCB (at B4)

7654321

8 Option

OffOnFree play
OnOn1 coin for 2 credits
OffOff1 coin for 1 credit <
OnOff2 coins for 1 credit
OffOffRight coin mechanism x 1 <4
OnOffRight coin mechanism x 4
OffOnRight coin mechanism x 5
OnOnRight coin mechanism x 6

Off Left coin mechanism x 1 <4 On Left coin mechanism x 2

OffOffOff

Off On Off

OnOnOff

Off Off On

On Off On

Off On On

No bonus coins @ For every 4 coins inserted, logic adds 1 more coin

For every 4 coins inserted, logic adds 2 more coins For every 5 coins inserted, logic adds 1 more coin For every 3 coins inserted, logic adds 1 more coin No bonus coins

No bonus coins

<4 Manufacturer's recommended settings

Table 1-2 Special Options

Settings of 4-Toggle Switch on Gravitar PCB (at P10/11)

4321

Option On Off Credits counted on one coin counter. Credits counted on two separate coin counters

Page 14

Set-Up Procedures Gravitar™

Table 1-3 Game Play Options

This table contains the switch settings for options relating to game difficulty, language, bonus, and ships. The switches are on the game PCB at location D4, and are accessible when the game PCB is mounted in place.

Settings of 8-Toggle Switch on Gravitar game PCB (at D4)

7654321

Option

OnOnNo bonus
OffOffBonus ship every 10,000 points <
OnOffBonus ship every 20,000 points
33zOffOnBonus ship every 30,000 points
883
2)=OnbaEasy game play <
3sOffSsHard game play
OffOff3 ships per game

On = Off 4 ships per game

OffOn5 ships per game
OnOn6 ships per game

“4Manufacturer's recommended settings

1-6

Page 15

Gravitar™

F. Self-Test Procedure

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. We suggest you perform the self-test procedure when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure. Wait at least 10 seconds after playing a game before entering self-test. Otherwise you may erase Set-Up Procedures

the top three scores in the high-score table or distort the statistics. All credits will be cancelled when you enter self-test. Refer to Figure 1-2 for the location of the self-test switch and option switches. To see the Operator Information Display, set the self-test switch to on (see Figure 1-3). To enter self-test, hold the FIRE button down while pressing 1-player start (see Figure 1-4). To end the self-test, set the self-test switch to off. The complete self-test procedure is explained in Chapter 2, Self-Test Procedure. \f a part of the test described in Figure 1-4 fails, refer to Chapter 2.

NO. OF CREDITS PER COIN FOR GAME DIFFICULTY RIGHT COIN MECHANISM a NO. OF CREDITS FOREACH PUSHOF ——___ UTILITY COIN SWITCH im _ eee BONUS ADDER PRESS START | AND FIRE

FOR TEST ““ _ INSTRUCTION FOR SELF-TEST OR TO ERASE SCORES OR TIMES NO. OF CREDITS PER COIN FOR LEFT COIN MECHANISM

ogooooo0<——————_ NO. OF GAMES PLAYED

on00 ee AVERAGE GAME TIME SHIPS PER GAME ———> OO a COCKTAIL CABINET

Figure 1-3 Operator Information Display

The Operator Information Display shows game statistics. You may also erase game scores and times. To see this display, set the self-test switch to on.

To erase game scores: To erase game times: 1, Push 1-PLAYER START until display 1. Push 1-PLAYER START until display To erase game scores and times:

  • Push 1-PLAYER START until display reads PRESS START 1 AND FIRE TO CLEAR SCORES.
  • Press both FIRE and 1-PLAYER START.
  • The word ERASING flashes on the screen until the entire table is erased. Wait until the word ERASING disappears before going on with other tests. eR reads PRESS START 1 AND FIRE TO CLEAR TIMES. ._ Press both FIRE and 1-PLAYER START. . The word ERASING flashes on the screen until the entire table is erased. Wait until the word ERASING disappears before going on with other tests. reads PRESS START 1 AND FIRE TO CLEAR TIMES AND SCORES. . Press both FIRE and 1-PLAYER START.
  • The word ERASING flashes on the screen until the entire table is erased. Wait until the word ERASING disappears before going on with other tests.

To end the Operator Information Display, set the self-test switch to off.

Page 16

Set-Up Procedures Gravitar™

Table 1-4 Self-Test Procedure

Instruction Test Passes

  • Set the self-test switch to on. While holding the FIRE but- The screen shows the self-test display. RAMs, ROMs, and three ton down, press ‘player start." integrated circuits are tested. If the screen is different from the self-test display, or if there are sounds, refer to Chapter 2, Self- Test Procedure.
  • Activate control panel and coin switches. As you activate the switches, you should hear a beep and the proper 0 should change to 1. If the test fails, refer to Chapter 2, Self-Test Procedure.
  • Observe the white frame at the sides of the screen. Each frame corner should be within 14-inch of each display bezel corner. If the test fails, refer to Chapter 2, Self-Test Procedure, Screen 2,

“All credits are cancelled when you enter self-test

SWITCHSWITCH AT B4SWITCHSWITCH — SWITCH AT D4SWITCH
TOGGLE 8(Coin modes)TOGGLE 1TOGGLE 8(Game play)TOGGLE 1

FRAME

SELF-TEST SWITCH

FOR TECHNICIANS OoOoOoOoOoOnOooOoOoOe ONLY RIGHT COIN PS SWITCH AT P10/11 MECHANISM tt O] i4eet (Special options)

LEFT COIN 7 MECHANISM I if

COIN SWITCH

START SWITCH (2 player)

SHIELD/TRACTOR (Player 1)

START SWITCH SHIELD/TRACTOR FIRE ROTATE RIGHT ROTATE LEFT \ THRUST (1 player)

(Player 2)(Player 1)(Player 1)(Player 2)(Player 2)

FIRE ROTATE RIGHT ROTATE LEFT THRUST (Player 2) (Player 2) (Player 1) (Player 1)

Figure 1-4 Self-Test Display

1-8

Page 17

Gravitar™

G. Game Play

Gravitar™ is a one- or two-player game with a color X-Y video display. This new display, with its 3 color guns and higher voltage, has the same technology that was used in previous Atari black-and-white X-Y displays. However, the screen now displays dazzling colors and unique visual effects. The player controls a space ship in three different solar systems. Each solar system consists of a home base, a death star, a red alien planet and four regular planets. Each planet has its own unique terrain. The red alien planet is the home of shooting alien ships. Some of the regular planets may have flying alien rammers to be avoided or shot down. The four planets all have fuel cells to be retrieved with a tractor beam and alien bunkers that fire shells. Successfully destroying all of the bunkers results in a MIS- SION COMPLETE message at the top of the screen. Achieving MISSION COMPLETE allows the player to collect bonus if he can evade the rammers when leaving the planet. If successful, he will be placed back in the solar system. A player has two ways to advance to the next solar system. The first is to successfully complete a mission on all four regular planets. The second way is to complete a mission on the red alien planet, which establishes a link into the next solar system. Gravitar™ has five possible modes of operation: demonstration, attract, play, high-score, and selftest. Self-test is a special mode for checking the game switches and computer functions. You may enter self-test ai any time. Wait at least ten seconds after a game has been played before entering selftest or turning off power; otherwise, you may erase the high-score table. Set-Up Procedures

  • Demonstration Mode The demonstration mode allows the operator to enter all planets to see their respective terrains and obstacles without being destroyed by shots from bunkers or alien space ships, or being hit by flying alien rammers. Enter this mode when you are in the Operator Information Display (see Figure 1-3) by simultaneously pressing all five player control buttons. To end this mode, set the seif-test switch to off.
  • Attract Mode The attract mode begins when power is applied to the game, after a play or high-score mode, or after self-test. This mode repeats every 30 seconds. It ends only when a credit is entered or when self-test begins. The screen displays one of four possible pictures in this mode. The first picture displays the singleplayer high-score table for approximately ten seconds. The words SCORE, FUEL, and GAME OVER appear. The words INSERT COIN and the coin mode appear if no coin(s) or not enough coins are inserted. The number of credits may show, if any. During this time the 1-player and 2-player red light-emitting diode (LED) lights flash.

Table 1-5 Gravitar™ High-Score Lists

Depending on the highest score, one of eight list names appears above the table of initials.

Name of List Points FLUNKY 0-20,000 GUNNER 20,001-40,000 CO-PILOT 40,001-80,000 PILOT 80,001-100,000 ACE PILOT 100,001-200,000 KILLER PILOT 200,001-400,000 PONTIUS PILATE 400,001-800,000 GOTTA-BE-LUCKY above 800,000

1-9

Page 18

Set-Up Procedures

The second picture spells GRAVITAR in expanding and contracting letters. It lasts approximately nine seconds. The third picture lasts about two seconds. The screen shows a solar system with a player's blue space ship in the center at home base. All planets and their respective bonus point values are visible. ATARI MCMLXXxXII copyright message appears in the center of this picture, and the number of credits (if any). DANGER appears above the death star. The ship flies toward the easiest planet in the upper right part of the screen. The fourth picture in this mode is a full-screen view of planet terrain with the player’s blue space ship appearing at the top center of the screen. The ship travels in the scrolling, zooming terrain until it crashes or is shot down. The words SHOOT BUN- KERS, TRACTOR FUEL, SCORE, FUEL, and number of credits (if any) are displayed. Game play begins when the correct credit(s) is entered and the 1- or 2-player button(s) is pressed.

  • Play Mode The play mode begins in the first solar system with the player's blue ship in the center of the screen at home base. There are four regular planets plus a fifth red alien planet and a death star arranged clockwise around the screen in increasing order of difficulty. The planets are worth 2,000, 4,000, 6,000, and 8,000 points with a value of 9,000 points on the alien planet. The positions of the alien planet and the death star vary in the second and third solar systems. After the first solar system all planets are valued at 9,000 points. The death star, located near home base, is the center of gravity in each solar system. Colliding with it results in the loss of one life, and the player returns to home base. The words SCORE (with current total score), FUEL (running total of original 10,000-point fuel supply), and BONUS (decreasing point value of planet under attack) appear at the top of the screen throughout game play.

1-10 Gravitar™

Player controls consist of LEFT ROTATE, RIGHT ROTATE, FIRE, THRUST, and TRACTOR/SHIELD yellow pushbuttons. Use FIRE to shoot targets. A player has four shells that must hit a target or must travel their full distance in order to be reloaded. TRACTORISHIELD retrieves fuel with a tractor beam and shields the ship from alien shots. The TRACTOR/SHIELD does not prevent the ship from crashing into land or alien ships. TRACTOR/SHIELD and THRUST decrease the player’s fuel supply. Using these controls together decreases the fuel supply even faster. Blue fuel cells are positioned just below a planet’s surface. There are two, three, or four fuel cells per planet terrain (depending on level of game play). Each cell beamed aboard ship with TRACTOR is worth 2,500 fuel units. If the player’s ship is above the highest point on some planet terrains, flying alien rammers attack him. Shooting a rammer scores 100 points. If the player gets too close to a shooting alien ship, he is involved in a one-on-one space dogfight, and either he or the alien ship must die. If the player is victorious, he returns to the solar system at his original spot; if the alien ship wins, the player loses a life and returns to home base. Red alien bunkers appear on each planet. There are two, four, six, or eight bunkers per surface (depending on the difficulty of the planet). The bunkers fire shots to protect the fuel cells. Exploding a bunker scores 250 points. Exploding all bunkers in a solar system displays a MISSION COMPLETE message. The word SUPERBONUS and the number of superbonus points appear in the middle of the screen only after a completed mission on the first planet in the first solar system. These superbonus points are awarded on the basis of initial difficulty of the first planet sucessfully completed. The higher the bonus point value of the planet attacked, the higher the superbonus awarded. No superbonus points are awarded for attacking the 2,000-point (easiest) planet or for attacking the four regular planets in consecutive order of difficulty.

Page 19

Gravitar™

Table 1-6 Gravitar™ Scoring

Planet Bonus* Superbonus** 9,000 20,000 8,000 12,000 6,000 6,000 4,000 2,000 2,000 0)

Obstacles Points

Red bunker 250 Rammer 100 Alien Ship 100

*Constantly decreases with elapsed game time ** awarded after first MISSION COMPLETE achieved

A player may fly to any planet he chooses. The number beside each planet is the starting number of bonus points for that planet. Entering a planet causes the distinct planet terrain to appear. To get maximum points, the player must shoot all alien bunkers. and see MISSION COMPLETE at the top of the screen. A player may exit a planet at any time; he does not have to stay any longer than he wishes. The red alien planet (worth 9,000 points) is home for red alien ships that must be shot down or avoided. The alien planet looks the same in every solar system: terrain consists of a spiral tunnel with a reactor at its end. Under a decrementing timer, the player must maneuver through the tunnel without hitting the walls and shoot the reactor. (Hitting the walls or not escaping in time places the player back at home base.) Shooting the reactor will make it glow and pulsate. Then the player must escape before the timer reaches zero. (In the next solar systems, the timer of the alien planet decreases by two seconds, and there are shooting bunkers to overcome.) Completing the mission on the alien planet places the player in the next solar system with an additional 7,500 fuel points. Gravitar progresses by waves of planets (new solar systems). Successfully destroying the reactor and escaping from the red alien planet, or achieving Set-Up Procedures

a MISSION COMPLETE on all four regular planets places the player in the next solar system (next level of game play). The four levels of game play are described as follows: a. Regular gravity b. Negative gravity c. Regular gravity with invisible landscape and maximum difficulty d. Negative gravity with invisible landscape and maximum difficulty Alien ship speed and firing frequency, rammer speed, bunker firing frequency, and bonus points are all based on time elapsed in game play. Both regular and negative gravity increase, depending on the initial planet bonus level. The game ends when all lives are used up or when player is out of fuel. Then the screen briefly displays the words SCORE, FUEL, PLAYER 1 (or 2), GAME OVER.

  • High-Score Mode This mode begins if a player has earned one of the eight highest scores. The player has one minute to enter his initials. Letters of the alphabet increment with LEFT ROTATE and decrement with RIGHT ROTATE pushbuttons. Select letters with the TRACTOR/SHIELD pushbutton. To reset the highscore table, power the game off and then on, or enter and end the self-test mode (this does not erase the top three scores).
  • Hints for Game Play @ Develop skill for controlling the space ship in regular and negative gravity. @ Beam up fuel cells with TRACTOR/SHIELD. @ Attack the red alien planet first for maximum challenge and 20,000 bonus points! Completion of this planet immediately places a player in the next solar system where all planets are worth 9,000 bonus points. @ Attack more difficult planets early in the game for higher bonus points. @ Many planet terrains have safe areas or “blind spots” from which the player can safely shoot at bunkers.
Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

Troubleshooting

This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you find the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is or isn’t working properly. The expanded self-test procedures in this chapter are included to help the qualified electronic technician troubleshoot the game.

Page 22

A. Comments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II PCB, or the video display?

The next step is to check all harness wires and connectors to the suspected failing assembly. If you find no harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly.

When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display is failing, we suggest that a qualified video display technician handle the troubleshooting and repair. If the power supply or Regulator/Audio I! PCB is failing, troubleshooting and repair are relatively simple, as these assemblies are not too complicated. If a game PCB is failing, troubleshooting and repair depends on your understanding of the operation of the PCB.

To effectively troubleshoot a game PCB, learn as Much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting the PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram.

The Schematic Package has signatures printed in red at the proper test-node points for PCB memory devices. For example, to determine if the self-test ROM is functioning properly, perform signature analysis with the ATARI® CAT Box. The Schematic Package. contains a complete description of signature analysis using the CAT Box.

A glossary of schematic signal descriptions is included in the Schematic Package. Each signal description states if the signal is hardware- or softwaregenerated, where it is generated, where it goes, and what it does. We suggest you use this glossary to become more familiar with the operation of the game PCB. Gravitar™

B. Self-Test Procedure

To enter Self-Test, set the self-test switch to the on position. Press FIRE and then 1-player start. If the test passes, the screen goes blank for a few seconds and then displays the picture below. See Chapter 1, Section F, Self-Test Procedure for a complete description of this picture.

Figure 2-1 Self-Test Screen 1 Test Passes

NOTE

This procedure does not test the coin door lockout coils and coin counter. If the lockout coils do not energize when the game is on, suspect the lockout coil wiring, coin door harness, game PCB harness, latch R9, or driver Q2 of the game PCB. Troubleshoot using the game schematics.

SCREEN 1: RAM failure is indicated by a sound and, if possible, an R displayed in the top center of the screen. Count the tones. One or two tones indicates RAM failure at game PCB location N/P1. Three or four tones indicate RAM failure at game PCB location K7.

Failing RAM Location Tone on Game PCB Ast or 2nd N/PT 3rd or 4th K7

Page 23

Gravitar™

ono1o0! 10

Figure 2-2 Self-Test Screen 1 Test Fails

ROM failure is indicated by one or more vertically arranged numbers displayed on the top half of the screen (see Figure 2-2). The bad ROM and its location are listed as follows:

Failing ROM Location Screen Display on Game PCB Oo" 7 1* MIN7 2* N/P7 a R7 4 D1 5 E/FA 6 H1 7 Jt 8 K/L1 gtr M1 “If this ROM is bad you will hear a constant low tone, and the program may be unable to display a screen image. “*If this ROM is bad, the screen may be blank.

EAROM or CUSTOM I/O CHIP failure is indicated by one letter in the top center of the sceen. Identify the failure with the table below.

Location Letter Displayed on Game PCB E EAROM at M2 P Custom I/O chip at C/D3 Q Custom 1/0 chip at B3 Troubleshooting

SWITCH failure is indicated by the associated 0 not changing to a 7 on the screen and no sound when the switch is activated. Troubleshoot using the information in Chapter 3, Section B, and game schematics. SOUND failure is indicated by no sound. Check the volume control levels on the utility panel, or troubleshoot using the game schematics. To see the remaining self-test screens (2 through 8), press the coin switch on the utility panel for each screen.

Figure 2-3 Self-Test Screen 2

SCREEN 2:

A white diagonai grid pattern and a complete character set appear on the screen (see Figure 2-3). The edges of the grid pattern should touch the sides of the screen. If the display is not centered, symmetrical, or the proper size, adjust the X SIZE, Y SIZE, X CTR, Y CTR, X LIN, OR Y LIN pots on the game PCB (refer to the Schematic Package). If the characters are incorrect, check again for a 2 displayed in the preceding ROM failure test.

Page 24

Troubleshooting

Figure 2-4 Self-Test Screen 3

SCREEN 3: A white box of decreasing size appears during this test. The box should shrink smoothly. There are seven stages, each with a tone. This pattern tests the binary and linear scaling circuitry. Troubleshoot using the game schematics.

Figure 2-5 Self-Test Screen 4

SCREEN 4: A series of horizontal lines are visible in the middle of the screen. This is a raster test, used by the manufacturer only, to set the color leveis. Gravitar™

RED (R) ROYAL BLUE (B) GREEN (G) \

WHITE (RGB) >

YELLOW (RG) LIGHT BLUE (GB) LAVENDER (RB)

Figure 2-6 Self-Test Screen 5

SCREEN 5: This test checks the seven screen colors and six intensities of each color (see Figure 2-6). If the intensities do not progress from dim at the top of each color group to bright at the bottom, there is a problem in the Z-axis of the game PCB or the video display. Use this pattern for tracking adjustments (refer to the color X-Y display manual).

Figure 2-7 Self-Test Screen 6

SCREEN 6: A grid pattern touches the corners of the video display (see Figure 2-7). Press the 1-player start button to change colors. Use this pattern for purity and convergence adjustments (refer to the color X-Y display manual).

Page 25

Gravitar™ Troubleshooting

VECTOR-GENERATOR DIAGNOSTIC PROGRAM

The diagnostic program is controlled by switches 2, 3, and 4 in These tests provide recurring sequences to make it easy for you the 4-toggle option switch bank at location P10/11 on the game to troubleshoot the vector-generator circuitry. The tests and their PCB. This group of switches lets you choose one of six tests. respective option switch settings are as follows:

TestActionSettings of 4-Position DIP

Switch at P10/11

432
Test 1Press WDDIS every 4 msec (blank screen)OffOffOff
Test 2Test vector-generator halt instructionOnOffOff

every .55 msec (blank screen)

Test 3Test vector-generator long vector (andOffOnOff

halt instruction) every 8.2 msec

Test 4Test vector-generator jump instructionOnOnOff

(and long vector and halt instruction) every 8.2 msec

Test 5Test vector-generator short vector instructionOffOffOn

(and all of Test 4) every 8.6 msec

Test 6Test vector-generator JSRL/RTSL instructionOnOffOn

(and all of Test 5) every 10.2 msec

Test 2Blank screenOffOnOn
Test 2Blank screenOnOnOn

Figure 2-8 Screen 7: Self-Test Screens During Signature Analysis

Press the coin switch while pressing the 2-player To exit from this screen, set the self-test switch to start button. The screen will either be blank or dis- off or press RESET on the game PCB. play vectors, depending on settings of the switch toggles at location P10/11 on the game PCB (see Figure 2-8).

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

Maintenance, Repair

and Parts

This chapter details maintenance and repair information and provides information you need to order parts for your Gravitar™ game. Please note that common hardware has been deleted from most of the parts lists. Common hardware includes screws, nuts, washers, bolts, and the like. The parts lists are arranged in alphanumeric order. For example, all A- prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-. When ordering parts, please give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed in the front of this manual for your convenience.

Page 28

Maintenance, Repair and Parts Gravitar™

A. Cabinet-Mounted Assemblies

Fluor. Tube & Speaker Assy. 178034-024 see Figure 3-4 (T-molding) 037332.01 (Vent. grille) A038164.01 (Cabinet assy.)

78-6900402 (Tape) 74-2110

037419-02 ‘A038590-01 (Access panel) Video Display see Figure 35

178013-001 (Latch)

Game PCB Assy. Control Panel As: r see Figures 92 & 33 , see Figures 3-7 & 38 a ‘A038586-01 037308-01 (Speaker grille) 148001-017 (Speaker) (Main harn. assy)

Regulator/Audio I! PCB Assy. see Figures 3-7 & 3-9

A038588-01 Coin Door Assy. (Power harn. assy.) see Figure 3-6

A037453-03, ‘A037454-03, A037455-03, or A037784-03 (Power cord) A038004-01 (Volume/self-test harn.) Power Supply Assy. perso see Figure 3-10 (Coin counter) 19-9032 (Volume control) 178048-001 A037470-01 (Caster) (On/off switch assy.) 009992.01 178070-001 (On/off switch cover) (Volume control knob) 78-3201 (Giid 62-041 (Glide)

(Utility coin switch) GGetttest switch 038003-01 Figure 3-1 Cabinet-Mounted Assemblies (Bracket) A038169-01 & -02 A

3-2

Page 29

Gravitar™ Maintenance, Repair and Parts

Figure 3-1 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) A002465-01 Coin Counter

A037453-03Strain-Relief Power Cord(U.S. and Canada)
A037455-03Strain-Relief Power Cord(Australia and New Zealand)

A037470-01 Power On/Off Switch/Mounting Plate Assembly

A037784-03Strain-Relief Power Cord(United Kingdom, Ireland, Lebanon, Saudi Arabia, India, Hong Kong,

Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe) A038604-01 Harness for Volume Control/Self-Test Switch/Coin Counter Assembly

A038164-01Cabinet Assembly(includes glides and PCB retainers, but not the rear access panel)

A038586-01 Main Harness Assembly A038588-01 Power Harness Assembly A038590-01 19-Inch Wells-Gardner Color X-Y Video Display Assembly The following four items are the technical information supplements to this game: SP-206 Gravitar Schematic Package ST-206-01 Gravitar Label with Self-Test Procedure and Option Switch Settings TM-183, Service Manual for 19-Inch Wells-Gardner Color X-Y Display TM-206 Gravitar Operation, Maintenance, and Service Manual 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Self-Test Switch

71-2110Lock Mechanism(for rear access panel)

78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x ¥%;Inch Thick 009992-01 On/Off Switch Cover 037308-01 Speaker Grille 037332-01 Ventilation Grille

037419-02Rear Access Panel(does not include lock)

038003-01 Bracket for Volume Control, Self-Test Switch, and Coin Counter(s)

038091-01Molded Coin BoxAcceptable substitute is part no. A037491-01

178013-001 Spring Draw Latch 178034-024 %-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster 178070-001 Volume Control Knob

3-3

Page 30

Maintenance, Repair and Parts

B. The Control Panel

WARNING Before removing or repairing any switch on the control panel, unplug the game.

To Open the Control Panel:

  • Open the coin door. Reach up through the opening to the top of the control panel and release the springdraw latches. (You may also release the spring-draw latches from the back of the game cabinet after opening the rear access panel.) 2, Close the coin door.
  • Lift up on the control panel at the top edge and tilt it toward you. There is foam tape on the display shield, which cushions the shield and prevents liquids from entering the cabinet interior. Make sure this tape is in good condition.

To Repair Leaf Switches:

  • Adjust the leaf switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Don’t burnish the contacts. To clean them, use electrical contact cleaner.
  • To replace a leaf switch, remove the screw with a Phillips-head screwdriver. Gravitar™
  • To replace the switch button, turn the stamped nut with a wrench in a counterclockwise direction as seen from inside the control panel. The ring on the outside of the control panel should not spin.
  • To reinstall the switch, reconnect the harness wires as shown in the Schematic Package, Game Wiring Diagram. Make certain the colored wires are routed to their matching colored tabs on the switch. To Repair LED Start and SELECT Switches: These switches have a very low failure rate. If a switch should ever be suspect, first test it using the following directions.

To Test LED Switch: |. Remove the wires from the suspected switch.

  • Attach the leads of an ohmmeter to normally open and common contacts.
  • Check contacts (push and release the switch button) for closed and open continuity. 4, If the contacts do not operate sharply or always remain closed or open, replace the switch.

To Replace LED Switch:

  • Remove all wires from the faulty switch.
  • Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel.
  • Install a new switch using the reverse procedure.
  • Reconnect the harness wires as shown in Figure 3-2.

1 PLAYER START

VIOLET

RED(+) NORMALLY OPEN piAck (N.0) CONTACT COMMON CONTACT

2 PLAYER START WHITE/BLACK ly veouey_—_i aw BROWN

= NORMALLY OPEN

(N.0) CONTACT BLACK COMMON CONTACT

Figure 3-2 Control Panel

Page 31

Gravitar™ Maintenance, Repair and Parts

WARNING Players may receive an electric shock if this contro! panel is not properly grounded! After (eral eonedeesn servicing any parts on the panel, check that 7 the ground wire is firmly attached to the metal 038173-01 tab on the inside of the control panel. Only (Control panel) then should you lock up the game.

038174-04 (Decal—not shown)

62-039 = (LED switch)

‘A038589-01 (Harness) 178030007 a (Yellow button)

160013-001 (Leaf switch/button holder) 036895-01 (Switch bezel)

Figure 3-3 Control Panel Assembly A038176-01 A Parts List

Part No. Description (Reference Designations and Locations in Bold) A038175-01 Control Panel with Decal A038589-01 Control Panel Harness Assembly 62-039 SPDT Momentary Pushbutton Start Switch with Red Light-Emitting Diode 036895-01 Black Molded Switch Bezel 038173-01 Control Panel 038174-04 Control Panel Decal 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-007 Yellow Pushbutton Assembly

Page 32

Maintenance, Repair and Parts Gravitar™

C. Fluorescent Tube and Speaker

WARNING Before removing or repairing the fluorescent tube or speaker, unplug the game.

If you drop a fluorescent tube and it breaks, it will im- Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start.

To Replace Cabinet Speakers:

plode! Shattered glass can fly six feet or more from the im-5.Upper speaker. Remove upper attraction glass. Slide

plosion. Use care when replacing any fluorescent tube. the fluorescent tube and speaker board Partially out of the cabinet. Turn it sideways to unplug the 5-pin har- To Replace Fluorescent Tube: ness connector. Remove the board from the cabinet.

  • Unplug the two plug-in connectors on the speaker.
1.pes ihe three sets i Lhe i ied the theNote that the white wire (+) connects on the side
per attraction panel retainer tothe cabinet. Loosenthemarked with a painted dot. Remove the hardware that

three sets of hardware that secure the lower retainer

to the cabinet. Lift theattractiJanel upand outofattaches the speaker to the board. Replace the
its|caife attraction p.Pp°speaker, reinstall the speaker board, and reconnect

its lower retainer. the harness.

2.Remove the cardboard locking tab at each end of the7.Lower

A speaker. Open the rear access panel. Unplug tube. Slightly spied we up or down and carefully the two plug-in connectors on the speaker. Note that remove it from the lampholders. the white wire (+) connects on the side marked with a

3.Replace with a new tube. Do not snap the tube in vig-painted dot. Remove the hardware that attaches the

orously—you may break it, causing an implosion! speaker to the cabinet. Install the new speaker, and re- Replace the locking tabs. place the hardware and connectors.

148001-017 Disassemble in the order indicat- © peaken ed. (Circled numbers match the 037309-01 79-561816P numbered instructions.) (Top retainer) (Wire nut)

038151-01 179035-001 (amntekion (Jumper wire) 142028-xxx (Transformer) 99-11003 oon A037457-01 99-11009 5) (Harness) (Socket)

038177-01 037469-01 (Attraction glass) (Bracket) 78-6900402 A037540-01 (Tape) (Ground wire)

(Bottom retainer) 037304-01 99-11006 (ab) NOTE

To ensure that the fluorescent tube 70-304 Starts, make sure the ground wire is firm- (Tube) ly attached to both ihe ballast transformer and the steel lamp bracket.

Figure 3-4 Fluorescent Tube and Speaker A038161-01 & -02 A

Page 33

Gravitar™ Maintenance, Repair and Parts

Figure 3-4 Fluorescent Tube and Speaker A038161-01 & -02 A Parts List

Part No. Description (Reference Designations and Locations in Bold) A037457-01 Tube and Speaker Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch, 15-W, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-inch Wide x ¥, inch Thick 79-561816P_ Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Lamp Starter

99-11006Fluorescent Lamp Locking Tab(tab consists of two pieces)

99-11009 Starter Socket 037304-01 Bottom Attraction Glass Retainer 037309-01 Top Attraction Glass Retainer 038151-01 15-Inch Jumper Wire 038177-01 Attraction Glass with Graphics 037469-01 Steel Lamp Bracket

142028-00160 Hz, 118 V, Ballast Transformer(used on A038161-01 assembly)
142028-00250 Hz, 118 V, Ballast Transformer(used on A038161-02 assembly)

148001-017 6 x 9Inch, 8 Q, 6-Ounce Oval Shielded High-Fidelity Speaker 179035-001 2-Pin Fluorescent Lampholder

3-7

Page 34

Maintenance, Repair and Parts

D. Video Display

To Remove Wells-Gardner Coior X-Y Display:

  • Open the rear access panel and unplug the 15-pin display harness connector. Remove the hardware that secures the display chassis to the metal bracket.
  • Open the control panel (see Figure 3-2).
  • Lift up on the glass shield. Slide the retainer clip off the wood cleat and remove it through the cutout. Now remove the glass shield by sliding it down and out of the cabinet. 4, Remove the cardboard bezel.
  • Remove the four sets of hardware that secure the display frame to the wood shelf.
  • Carefully pull the display out through the front of the cabinet. Place it on a soft mat in a protected location. Gravitar™
WARNING

SHOCK HAZARD The following procedure should only be performed by a qualified service technician. Before removing or repairing the video display, unplug the game. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube. High voltages may exist in any video display, even with power disconnected. Use extreme

caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! IMPLOSION HAZARD If you drop the display and the picture tube breaks, it will implode! Shattered glass and the yoke can fly six feet or more from the implosion. Use care when replacing any display.

Figure 3-5 Video Display Parts List

Part No. Description (Reference Designations and Locations in Bold)

Wells-Gardner Display A038590-01

A038593-01 Wells-Gardner Interconnect Assembly 92-053 19-Inch Wells-Gardner Color X-Y Video Display 038181-01 Video Display Support Bracket 037303-01 Display Shield 037322-01 Display Bezel 037330-01 Display Shield Retainer Clip

92-053 (Wells-Gardner Display)

SCREEN (Brightness)

FOCUS

BACK OF DISPLAY

Page 35

Gravitar™ Maintenance, Repair and Parts

© 92-053 . (Wells-Gardner Display) A038593-01 @ (Display interconnect assy.) 037322-01 (Bezel)

037303-01 (Shield)

038181-01 ® (Bracket)

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

037330-01 (Retainer clip)

Figure 3-5 Video Display, continued A038590-01

3-9

Page 36

E. Coin Door

(Screw for Bezel) 170000-001 (Lamp)

179047-001 (Lamp Base)

ae . 99-15040 = 99-15026 (Lever) 99-15056 (Coin Inlet)

99-15025 ——» “ (Coin Inlet) CO, PART OF a 99-15041 ue 99-15054 99-15055 99-15041 (Pivot for Lever) (Retng, Screw) (Lockout Coil) { 99-15053 (Lockt. Coil Spring) 99-15027 SS (Coin Ret. Box) ~

@ .

75-9148 (Hex Nut) +——~ 99-15028 (Coin Ret. Box)

75-056 (Lock Wash.)

(Sw. Adjuster) 99-15056 (Screw for Bezel) 99-15060 (Sw. Cover) 99-15029 (Brackel) 99-1: soa. 8 (Switch)

75-3414S (Screw)

7214148 (Screw)

Figure 3-6 Vertically Mounted Coin Door A037619-xx D

3-10

Page 37

Gravitar™

A037542-01 (Harness—not shown)

99-15063 (Screw)

99-15067 (Lock Assy.)

O=n

038091-01 (Coin Box)

99-15072 (Door Frame)

99-15073

A037619-01 — U.S, 25¢/25¢ Coin Door A037619-02 — U.S. 50¢/50¢ Coin Door ‘A037619-03 — Canadian 25¢/25¢ Coin Door A037619-04 — British 10 P/10 P Coin Door A037619:05 — British 10 P/50 P Coin Door A037619-06 — British 20 P/50 P Coin Door A037619-07 — Australian 20¢/20¢ Coin Door 99-15070 (Upper Door) | (Doors and Frame) 99-15074 (Lower Door)

A037619-08 — German 1 DM/1 DM Coin Door ‘A037619-09 — German 2 DM/1 DM Coin Door ‘A037619-10 — German 2 DM/5 DM Coin Door ‘A037619-11 — German 1 DM/5 DM Coin Door ‘A037619-12 — 5 Fr/5 Fr Coin Door A037619-13 — Swiss 1 Fi/1 Fr Coin Door A037619-14 — French 1 Frit Fr Coin Door Maintenance, Repair and Parts

99-15038 (Bezel for Button)

9915001 thru 99-15011 (Return Button)

99-15071 (Clamp)

‘99-15039 ES (Bezel for Cover)

99-15036 (Cover

99-15066 (Screw)

A037619-15 — French 2 Fi!1 Fr Coin Door A037619-16 — Swedish 1 Ks!1 Kr Coin Door ‘A037619-17 — Spanish 25 Pts/25 Pts Coin Door ‘A037619-18 — Italian 100 L/100 L Coin Door ‘4037619-19 — Hong Kong $1/$1 Coin Door ‘A037619-20 — Japanese 100Y/100Y Coin Door

Figure 3-6 Vertically Mounted Coin Door, continued A037619-xx D

Page 38

Maintenance, Repair and Parts Gravitar™

Figure 3-6 Vertically Mounted Coin Door, continued Parts List

Part No. Description 038091-01 Coin Box (Not included in assembly) Acceptable substitute is part number A037491-01. A037542-01 Harness Assembly 721414S #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-914S #4-40 Steel Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25%) 99-15031 Switch Adjuster 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S, 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x %,-Inch Cross-Recessed Pan-Head Stee| Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15068 Lockout Coil 99-15069 Spring for Lockout Coil 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 170000-001 6.3V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

3-12

Page 39

Gravitar™

F. Printed-Circuit Boards

A— warnine Before removing or repairing any printedcircuit board, unplug the game.

To Remove Printed-Circuit Boards:

  • Open the rear access panel.
  • For the game PCB, unplug the two edge connectors. Remove the screw and spacer that secure the PCB to the cabinet. Carefully slide the PCB straight out of its slots. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required.
  • For the Regulator/Audio |] PCB, disconnect ihe five small harness connectors on this board. Maintenance, Repair and Parts

Remove the screw and spacer that secure the Regulator!Audio II PCB to the cabinet, and carefully remove the board from its slot. Do not twist the board, as this may loosen connections or components. Replace or repair as required and reinstall. Make sure that the connectors on the PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. Replace the hardware that secures the Regulator/Audio || PCB to the cabinet wall. Reinstall the plug-in connectors to the PCB. Close and lock the rear access panel. Ensure that the operation of the game is correct by performing the self-test. Performing self-test is very

important when you repair a PCB.

72.6810S (Screw)

  • 175004-706 (Spacer) 034536-02 (Foam pad)

‘A038398-21 sO) (Game PCB)

A035435-04 (Regulator! Audio I! PCB)

034536-02 (Foam pad)

Figure 3-7 Printed-Circuit Board Removal

Page 40

Maintenance, Repair and Parts Gravitar™

| = i

i i

aR

Figure 3-8 Gravitar™ Game PCB Assembly A038398-21 & -22 A

3-14

Page 41

Gravitar™ Maintenance, Repair and Parts

Figure 3-8 Gravitar™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) For A038398-21 Version Only 27-102182 0.0018 uF, + 10%, 1 kV Radial-Lead Ceramic-Disc Capacitor (C79)

140000-10310 k2, +5%, % W Resistor(R86, 92, 93)

122002-104 0.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor (C67, 69, 74, 75) 137160-003 10-Bit Digital-to-Analog Converter (C9, E9) For A038398-22 Version Only 21-101103 0.01 uF, + 10%, 100 V, Radial-Lead Epoxy-Dipped Capacitor (C77) 27-102182 0.0018 uF, + 10%, 1 kV, Ceramic-Disc Radial-Lead Capacitor (C65)

110000-681680 2, +5%, % W Resistor(R83)

110000-821 820 Q, +5%, % W Resistor (R84, 94, 95) 122002-104 0.1 uF, 50 V, Ceramic-Disc Radlal-Lead Capacitor (C64, 66, 76, 78) 137158-002 12-Bit Digital-to-Analog Converter (A/B9, F9) For A038398-21 & -22 Versions 19-315103 10 k& Vertical PCB-Mounting Cermet Trimpot (R189, 192, 212, 213) Acceptable substitute is pari mo. 119002-103. 19-315202 2 kQ Vertical PCB-Mounting Cermet Trimpot (R187, 210) Acceptable substitute is part no. 119002-202. 19-315501 200 © Vertical PCB-Mounting Cermet Trimpot (R98, 99) Acceptable substitute is part no. 1149002-501. 21-101153 0.015 uF, + 10%, 100 V Radial-Lead Epoxy-Dipped Mylar Capacitor (C31, 32) 24-250226 22 uF, 25 V Electrolytic Fixed Axial-Lead Capacitor (C111, 121) 24-350107 100 uF, 35 V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C117, 119, 120) 24-500106 10 uF, 50 V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C17, 36, 38, 39) 24-500476 47 uF, 50 V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C16) 31-1N100 Type-1N100, 100 V Switching Diode (CRI, 2, 5, 7)

31-1N914Type-1N914, 75 V Switching Diode(CR3, 4)

33-2N3906, Type-2N3906 PCB Switching and Amplifying Transistor (Q7, 11) 34-2N3904 Type-2N3904, 60 V, 1 W NPN Transistor (Q1, 5, 6, 8-10, 12) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q2-4)

37-555Type-555 Integrated Circuit(A4)
37-1495Type-MC14951L Integrated Circuit(A/B11, A/B12, C11, C12)
37-7433Type-7433 Integrated Circult(L140)
37-13201Type-LF13201 Integrated Circuit(B10, E10)
37-74109Type-74109 Integrated Circuit(E5)
37-74193Type-74193 Integrated Circuit(E4)
37-LM324Type-LM324 Integrated Circuit(B5, D5)
37-74LS00Type-74LS00 Integrated Circuit(ES, L3)
37-74LS02Type-74LS02 Integrated Circuit(K5, K6, N5)
3?7-74LS04Type-74LS04 integrated Circuit(J3, K9)
37-74LS08Type-74LS08 Integrated Circuit(L4, L6)
37-74LS14Type-74LS14 Integrated Circuit(F7)
37-74LS20Type-74LS20 Integrated Circuit(H3, H5)
37-74LS27Type-74LS27 Integrated Circuit14)
37-74LS32Type-74LS32 Integrated Circuit(J6, M5, R4)

[Continued on next page]

3-15

Page 42

Maintenance, Repair and Parts Gravitar™

Figure 3-8 Gravitar" Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

37-74LS42Type-74LS42 Integrated Circuit(H7)
37-74LS74Type-74LS74 Integrated Circuit(K3, L5)
37-74LS139Type-74LS139 Integrated Circuit(J7)
37-74LS157Type-74LS157 Integrated Circuit(F6, K8, L8, M8, N3, N8, R3)
37-74LS161Type-74LS161 Integrated Circuit(J4, M6, N6, P6, R6)
37-74LS164Type-74LS164 Integrated Circuit(M3)
37-74LS174Type-74LS174 Integrated Circuit(P2, P4)
37-74LS175Type-74LS175 Integrated Circuit(C6, D6, D7, E6, H6, K2, K10)
37-74LS191Type-74LS191 Integrated Circuit(C7)
37-74LS194Type-74LS194 Integrated Circuit(A8, B8, C8, F8, H8, J8)
37-74LS244Type-74LS244 Integrated Circuit(B1, C1, E2, H2, L9, M9, N9)
37-74LS245Type-74LS245 Integrated Circuit(F2, P8)
37-74LS273Type-74LS273 Integrated Circuit(E8, R9)
37-74LS374Type-74LS374 Integrated Circuit(J2)
37-74LS393Type-74LS393 Integrated Circuit(F4, H4)
37-74S00Type-74S00 Integrated Circuit(E7)
37-74802Type-74S02 Integrated Circuit(B7)
37-74804Type-74S04 Integrated Circuit(F3)
37-74S74Type-74S74 Integrated Circuit(A6, A7)
37-74S260Type-74S260 Integrated Circuit(J5)

37-7815 +15 V Voltage Regulator (VR2) 37-7915 — 15 V Voltage Regulator (VR1)

37-TLO82CPType-TLO82 Integrated Circuit(A10, D10, D/E11, D/E12, R8)

38-MV5053 Type-MV5053 Light-Emitting Diode (CR6) 41-3003 100 pH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (Lt-3) Acceptable substitute is part no. 141002-001, 66-114P1T 4-Station Single-Throw, Dual-Inline-Package Bit Switch (P10) 66-118P1T 8-Station Single-Throw, Dual-Inline-Package Bit Switch (B4, D4)

72-6810S#8 x %-Inch Phillips-Head Screw(secures PCB to cabinet)
79-42C2222-Contact Medium-Insertion-Force Integrated Circuit Socket(M2)
79-42C2424-Contact Medium-Insertion-Force Integrated Circuit Socket(D1, E/F1, H1, J1, K7, K/L1, L7, M1,

MIN7, N/P1, N/P7, R7)

79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(B3, C2, C/D3, J9)

81-4302 Nylon Snap-In Fastener 90-6013 Microprocessor (C2) 034536-02 Foam Pad 038178-03 Dual-Slotted PCB Retainer

110000-101100 Q, +5%, % W Resistor(R90, 91)

110000-102 1kQ, +5%, % W Resistor (R19, 23, 47, 51, 55, 71, 82, 104-106, 108-113, 121-127, 139-143, 149, 152, 156, 160, 182, 204)

110000-10310 kQ, +5%, % W Resistor(R1-18, 20-22, 24-41, 46, 58, 61-68, 72, 136-138, 159, 179, 200, 202)

110000104 100 k2, +5%, % W Resistor (R45, 50, 74-81) 110000-105 1M&, +5%, % W Resistor (R43, 44, 48)

110000-1221.2 kQ, +5%, % W Resistor(R59, 190)

110000-123 12 kQ, +5%, % W Resistor (R177) 110000-151 150 2, +5%, V4 W Resistor (R107) 110000-153 15 kQ, +5%, % W Resistor (R150, 161) [Continued on next page]

3-16

Page 43

Gravitar™ Maintenance, Repair and Parts

Figure 3-8 Gravitar™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

110000-221 220 2, +5%, % W Resistor (R42, 73, 102, 103) 110000-222 2.2 kQ, +5%, Vs W Resistor (R57, 173-175, 185, 196-198, 207) 110000-223 22 kQ, +5%, % W Resistor (R69, 155)

110000-27027 2, +5%, V4 W Resistor(R157)

110000-272 2.7 kQ, +5%, v4 W Resistor (R181, 205) 110000-332 3.3 kQ, +5%, Vs W Resistor (R53, 54)

110000-3923.9 kQ, +5%, v4 W Resistor(R49, 52, 60, 89, 178, 183, 186, 201, 206, 208)

110000-471 470 Q, +5%, va W Resistor (R114-119, 128-131, 133-135, 144-148, 151, 154, 158, 169, 170, 176, 184, 193, 194, 199, 209) 110000-472 4.7 kQ, +5%, v4 W Resistor (R56) 110000-561 560 2, +5%, % W Resistor (R164)

110000-5625.6 kQ, +5%, % W Resistor(R188, 211)

110000-680 68 2, 5%, Vs W Resistor (R153) 110000-681 680 2, +5%, % W Resistor (R180, 203)

110000-68368 kQ, +5%, %4 W Resistor(R70)
110001-271270 2, +5%, V2 W Resistor(R195)
110003-7527.5 kQ, +1%, 4 W Resistor(R87, 88, 96, 97, 100, 101, 162, 163, 165-168)
110004-001Voltage Dependent Resistor(RV1, 2)

121007-473 0.047 uF, + 10%, 50 V, Radial-Lead Epoxy-Dipped Polycarbonate Capacitor (C72, 80) 122000-225 2.2 pF, + 10%, 35 V Tantalum Capacitor (C110) 122002-102 0,001 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor (C27, 28) 122002-104 0.1 pF, 50 V, Ceramic-Disc Radial-Lead Capacitor (C1-15, 18-22, 25, 26, 29, 35, 37, 40-43, 45-63, 70, 73, 81-84, 86-101, 103-109, 114-116, 122-126, 130, 131, 134, 135) 122005-103 0.01 pF, 25 V, Ceramic-Disc Radial-Lead Capacitor (C44, 71) 122008-224 0.22 uF, 25 V, Ceramic-Disc Radial-Lead Capacitor (C30, 33, 34)

128002-10010 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor(C85)
128002-101100 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor(C23, 129)
128002-1021000 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor(C136, 137)
128002-151150 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor(C113)

128002-221 220 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor (C118) 128002-390 39 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor (C24, 112, 127, 132)

131002-001Type-1N754A, 6.8 V Zener Diode(CR8)
136002-125Programmable Read-Only Memory(N4)
1386010-101Programmabie Read-Only Memory(D1)
136010-102Programmable Read-Only Memory(E/F1)
136010-103Programmable Read-Only Memory(H1)
136010-104Programmable Read-Only Memory(v1)
136010-105Programmable Read-Only Memory(K/L1)
136010-106Programmable Read-Only Memory(M1)
136010-107Programmable Read-Only Memory(MIN7)
136010-108Programmable Read-Only Memory(N/P7)
136010-109Programmable Read-Only Memory(R7)
136010-110Programmable Read-Only Memory(L7)
136010-111Programmable Read-Only Memory(R1)
136010-112,Programmable Read-Only Memory(R2)
137002-001Type-74S86 Integrated Circuit(B6)

[Continued on next page]

3-17

Page 44

Maintenance, Repair and Parts Gravitar™

Figure 3-8 Gravitar™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

137149-001Type-74LS11 Integrated Circuit(F5)

137159-001 8-Bit Digital-to-Analog Converter (D9) 137161-001 Electrically-Alterable Read-Only Memory (M2)

137177-001Type-74LS138 Integrated Circuit(P3)

137179-001 Address Controller (J9) 137211-001 Random-Access Memory (N/P1, K7)

137236-001Type-74S10 Integrated Circuit(K4)
144000-00112.096 MHz, +.005% Crystal(Y1)

175004-706 #8 Spacer (secures PCB to cabinet) 179051-002 Test Point Acceptable substitute is part no. 020670-01. C012294-01 Audio I/O N-Channel MOS/LSI Custom Chip (B3, C/D3)

Page 45

Gravitar™

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atar, inc., Sunnyvale, CA. This drawing |s only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, oF license to use, the subject matter of the drawing or any design oF technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except tor ‘manufacture by vendors of Atari, Inc., and for manufacture under the cotporation’s written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation, Maintenance, Repair and Parts

R33, eee Set 5 7

LtSePI
isoYg

_ (eR? 0 cRS f= co

C20Cel0

C19

+3300-—

35V

C18

ps2 a) 5.6K

oO 4Rz4,10,7WE- oO

TIP32 TDAZ002A TDA20C2A =IQ2_IN4002 Q5 7 cra} T ROEa nt C7 ay C337R3 c6lm 0 “]x\0 cega J=|e oa RIstek 0 3 & afl =8 s5e,, & Rae & 4ogoeh Ca 470 470 + © eles 9 RI _]

  • 0 220 R30 RP, 1/2W Ot cr: 4 oF Ns002 iz) 0 —4+ 3300urF = }— bs 350"

Figure 3-9 Regulator/Audio Il PCB Assembly A035435-04

3419

Page 46

Maintenance, Repair and Parts Gravitar™

Figure 3-9 Regulator/Audio I! PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold) 19-100P1015 0.1 2, +3%, 7 W Wirewound Resistor (R24)

19-3151021 k& Vertical PCB-Mounting Cermet Trimpot(R8) Acceptable substitute is part no. 119002-102

24-250108 1000 uF, 25 V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C13) 24-250477 470 uF, 25 V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C1, 4, 12) 24-350338 3300 uF, 35 V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C9, 10, 18, 19) 29-088 0.1 uF, 50 V Ceramic-Disc Axial-Lead Capacitor (C3, 11, 20, 21) 31-1N4002 Type-1N4002, 100 V, 1 A Silicon Rectifier Diode (CR1, 4) 31-1N5401 Type-1N5401, 100 V, 3 A Silicon Rectifier Diode (CR5-8) 33-TIP32 Type-TIP32 PNP Power Transistor (Q2) 34-2N3055 Type-2N3055 NPN Silicon Transistor (Q3)

37-LM3055 V Linear Voltage Regulator(Q1)

72-1608C #6-32 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw (Q3) 72-6606S #6 x ¥-Inch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc-Plated-Steel Screw (Q5, 7)

72-6810S#8 x %-Inch Phillips-Head Screw(attaches PCB to cabinet wall)
75-F60405#6-32 x ¥%4-Inch Binder-Head Nylon Screw(Q2)
75-99516#6-32 Nut/Washer Assembly(Q3)
78-16008Thermally Conductive Compound(Q3)

78-16014 Thermally Conductive Silicon Insulator (Q2) 79-58306 6-Position Connector Receptacle (J6, 9)

79-583089-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)
79-583544-Position Connector Receptacle(J8)

034531-01 Heat Sink 034536-02 Foam Vibration Damper 100015-103 0.01 wF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor (C5, C14) Acceptable substitute is part no. 122005-103 110000-010 12, +5%, V4 W Resistor (R10, 19) 110000-100 10 2, +5%, % W Resistor (R11, 20, 29, 30)

110000-101100 2, +5%, % W Resistor(R4, 12, 22)

110000-102 1kQ, +5%, % W Resistor (R27, 28)

110000-10310 k2, +5%, ¥4 W Resistor(R13, 14)
110000-271270 2, +5%, V4 W Resistor(R1)
110000-33033.2, +5%, V4 W Resistor(R3)
110000-3923.9 kQ, +5%, V4 W Resistor(R6)
110000-5625.6 kQ, +5%, % W Resistor(R32, 33)
110000-7527.5 kQ, +5%, % W Resistor(R7)
110007-221220 2, +5%, v2 W Resistor(R9, 21)

110009-027 2.7 2, +5%, 1 W Resistor (R5) 122002-102 0,001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor (C2, 7, 16) 122004-224 0.22 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor (C6, 8, 15, 17) 137151-002 Type-TDA2002A 8 W Linear Audio Amplifier Integrated Circuit (Q5, 7)

175004-708#8 Spacer for Mounting Printed Circuit Board(2 required)

179051-002 Test Point Acceptable substitute is part no. 020670-01

3-20

Page 47

Gravitar™ Maintenance, Repair and Parts

G. Power Supply Assembly »S

‘A037395-01 (Transformer Assy.)

A021084-xx (Volt. Plugs)

29-053 (ceresion SS f 78-70501SC | (Cap. Bracket) ' 034544-01 (Fuse Block Cyr.)

79-4411001 (Fuse Post)

46-2017002 (Fuse)

A035891-01 (Fuse Harness) 034482-02 (Chassis)

46-301203 (Fuse)

037639-01 (Label)

78-2708 (Bushing)

A034630-01 79-3206 (Filter Assy.) (Fuse Block) 037641-01 46-2014002 atabel) \ (Fuses) 5 ] A035890-01 79-15021001 q : (Term. Block) \ \ (Pwr. Harness)

4034629-01 3A-MDA3501 © on (Rectifier) (AG. Harn)

Figure 3-10 Color X-Y Power Supply Assemblies A037396-xx B

3-21

Page 48

Maintenance, Repair and Parts Gravitar™

Figure 3-10 Color X-Y Power Supply Assemblies Parts List

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100 V_(violet)
A021084-02Voltage Plug for 120 V_(yellow)
A021084-04Voltage Plug for 220 V(blue)
A021084-05,Voltage Plug for 240 V_(brown)

A034629-01 AC Harness Assembly

A034630-01RFI Filter Assembly(FL1)

A035890-01 Power Harness Assembly A035891-02 Fuse Harness Assembly A037395-01 Color X-Y Transformer Assembly (T1) 29-053 27,000 uF 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Type-MDA 3501 Bridge Rectifier (CR1)

46-20140024 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30120320 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x %,-Inch Outside Diameter x V-Inch Thick 78-70501SC. 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis Base 03454401 Fuse Block Cover 037243-01 Metal Base Plate (not shown in illustration)

037639-01Label for Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)
NOTE 037396-01 power supply assembly has the 120 V plug A037396-02 has the 100 V, 220 V, and 240 V plugs A037396-03 has the 220 V and 240 V plugs

Line Voltage Range Voltage Selection Plug Wire Color 90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown

WARNING Fuse cover must be in place during game operation.

3-22

Page 49

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm O Distributor

Address 1 Operator City State Zip O Other. Gravitar™ 1st printing

Area Code Phone

Page 50

First fold

No Postage Necessary if mailed in the United States

a

BUSINESS REPLY MAIL a FIRSTCLASS PERMIT NO. 1004 SUNNYVALE, CA Eee

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. De] Attn.: Field Service/Coin-Op Division Eee P. O. Box 427 Sunnyvale, California 94086 Ft

Le |

~ TT Second fold —_ ~~ —_

Wwol4 ebpe sty adey

Page 51

‘Seller warrants that its printed-circuit boards and parts thereon are free from detects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment, None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform {o this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;

(b) Such products are returned prepaid to Sellers’ plant; and

  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others, Be very cautious in using non-Atari-supplied components with our games. in order to insure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor. This document is and contains confidential trade secret information of Atari, Inc. This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc. Neither it nor the information it contains may be reproduced, used, or disclosed to persons not havjing a need to know consistent with the purpose of the loan. without written consent of Atari, Inc,

Page 52

(i ~

790 SYCAMORE DRIVE

PO. BOX 906 ATARI, INC.

MILPITAS, CALIFORNIA 95035

408/942-3100 ¢ TELEX 35-7488