Orbit TM-127 1st Printing
Orbit (Atari, 1978) · Technical Manual · 108 pages · 64 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the label located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service. tee
ORBIT’
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Catalog ATARI INC. 1265 BORREGAS AVENUE PO. BOX 9027 SUNNYVALE. CALIFORNIA 94086 408'745-2000 » TELEX 35-7488
A.
ATARI
‘A Warner Communications Company Cw)
Copyright © 1978 by Atari, Inc. All rights reserved
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor
may it be stored in a retrieval system, transmitted, or otherwise copied for
public or private use, without permission from the publisher.
For permissions request, write:
ATARI INC 1265 Borregas Avenue P.O. Box 9027 Sunnyvale, California 94086
10G
Lithographed in the U.S.A
ii ORBIT
TABLE OF CONTENTS
1 LOCATION SETUP A. INTRODUCTION . = B. GAME INSPECTION woneeet C. INSTALLATION REQUIREMENTS Line Voltage Selection Type of Power Cord ............ D. INTERLOCK, POWER ON/OFF SWITCH AND OTHER RELATED OPERATOR CONTROLS. ..0 2.0... cece eects 1-3 Interlock Switch Checkout Procedure E. OPERATOR OPTIONS F. SELF-TEST PROCEDURE... G. VOLUMECONTROL ......
2 GAME PLAY
3 THEORY OF OPERATION A. GENERAL INFORMATION . B. POWERSUPPLY ........... C. MICROPROCESSOR CIRCUITRY MPU, ROM and RAM. Address Decoding wae ®land ©2Clock Driver ....... Watchdog RESET........ SYNC GENERATOR . ALPHANUMERIC/PLAYFIELD GENERATOR. MOTION OBJECT GENERATOR . VIDEO OUTPUT ..... AUDIO GENERATOR ........ DUAL AUDIO GENERATOR...............-++ Srammos
4 MAINTENANCE AND ADJUSTMENTS A. CLEANING ....... B. COIN MECHANISM Components on Coin Door . Access to Coin Mechanisms Cleaning of Coin Paths . Lubrication............. Adjustment of Coin Switch Trip Wire. . Mechanical Adjustments on Coin Mechanism . . General Troubleshooting Hints .. . . TV MONITOR ADJUSTMENTS... ee FUSE REPLACEMENT ................ LICON SWITCH REMOVAL TV MONITOR REMOVAL . =™mMoOO
ORBIT iii
TABLE OF CONTENTS
iv ORBIT 5 ILLUSTRATED PARTS CATALOG
Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4 Figure 1-5 Figure 1-6 Figure 1-7 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10
Figure 3-11 Figure 3-12 Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16 Figure 3-17 Figure 3-18 Figure 3-19 Figure 3-20 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Orbit Control Panel ..... - Voltage Selection Connetors AC Line Voltage Check... . Location Set Requirements Location of Interlock and Power On/Off Switches . Option DIP Switches and Game PCB Location and Removal . Location of Self-Test Switch and Volume Controls . “3 Attract Mode .. Freeze Mode . . Ready-To-Play Mode. . . Reset Mode........... Play Mode ... Playfield and Motion Object Display . Location of Game Levels and Starship Controls . . Location of Game Option Pushbuttons. . Selected Game Options Score and Data Display Portion of TV Screen. . . Orbit Game Block Diagram ...... Orbit PCB Block Diagram On-Board Supply Schematic Diagram . Power Supply Simplified Block Diagram Microprocessor Schematic Diagram . . Memory Block Diagram Address Decoding ...... ® Land 02 Clock Driver Signal. Sync Generator Schematic Diagram Simplified Diagram of Crystal-Controlled Oscillator and TV Sync Circuitry .....-.... ba . Horizontal Sync Timing Diagram Vertical Sync Timing Diagram . . Alphanumerics Generator Block Diagram . Alphanumerics Generator Simplified Schematic Diagram - Playfield Generator Block Diagram and Simplified Schematic Diagram . 3-17 Display RAM Simplified Schematic Diagram . . : Motion Object Generator Block Diagram . . Video Circuit Simplified Schematic Diagram . . . . Audio Generator Simplified Schematic Diagram . Duai Audio Amplifier Simplified Schematic Diagram . Coin Door Assembly ... : Hinging Open the Magnet Gate Assembly Removal of Coin Mechanism............ Surfaces to Clean Inside the Coin Mechanism. . Removal of Plate Covering Rear of Coin Slot . Close-up View of Lubrication Point ....... Detail View of Coin Switch and Trip Wire . . .
LIST OF ILLUSTRATIONS
Figure 4-8 Adjustments on Coin Mechanism... .. . . 4.5 Figure 4-9 — Locations of Adjustments on TV Chassis . . . 4-6 Figure 4-10 LICON Switch Removal 4-7 Figure 4-11 TV Monitor Removal. . - 48 Figure 5-1 Orbit Final Assembly . 52 Figure 5-2 TV Monitor Assembly . . 5-6 Figure 5-3. Type B Power Supply . . 5-8 Figure 5-4 — Coin Door Assembly 5-10 Figure 5-5 — Front Bezel Assembly... . . : 5-12 Figure 5-6 Coin Lockout Assembly ........ . . 5-13 Figure 5-7 Coin Switch Assembly ........... 5-13 Figure 5-8 Control Panel Assembly... .... . as get 5-14 Figure 5-9 — Strain Relief Power Cord Assembiy ..... . bees 5-15 Figure 5-10 On/Off Switch Assembly ...... Leben eee seeee ee. 516 Figure 5-12 interlock Switch Assembly ...... . arrres . 22... 517 Figure 5-13 LED Pushbutton Switch Assembly (Red) EF OA Figure 5-14 RF Shield PCB Assembly... .... cee eee voce eee es, BR Figure 5-15 Dual Audio Amplifier PCB Assembly eee eee 2... 5-19 Figure 5-16 Orbit PCB Assembly ......... Bate ewe neon fea eng ig gown BQ
Table 1-1 Installation Requirements......... 1-4 Table 1-2 8-Toggle DIP Option Settings . . . . 1-7 Table 1-3 Self-Test Procedure .............. 18 Table 2-1 Player Controls... 2.6.6.0 eee 2-4 Table 2-2. Game Levels 2.5 Table 2-3. Game Options ... . rear ve. 2:6 Table 3-1 © MPU Input/Output Signal Descriptions ct HE ewan ee hE R ee eee 3-9 Table 3-2 Atari Programmed Memory Map............ SIC E> C0)
Appendix A Reference Schematic Drawings Appendix B Atari Customer Service Information
ORBIT v
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
A. INTRODUCTION
Orbit is a two-player game developed by Atari, Inc. The game is packaged in an upright, floor-resting cabinet illustrated by brightly colored orange, red and blue graphics to further enhance potential play. A 23-inch TV monitor is mounted in the top front of the cabinet with the monitor screen tilted back from the vertical. The TV monitor viewing screen is shielded by a Plexiglas® panel that also displays colorful graphics.
Player-operated controls are mounted on a control panel directly below the TV monitor viewing screen on the front of the game cabinet as illustrated in Figure 1-1. The controls consist of a Game Select, Game Option, and Starship Control pushbutton switches.
Cc GAME SELECTION |
LEFT-PLAYER
STARSHIP SSS
RIGHT-PLAYER re CONTROL CONTROLS
HYPERSPACE RESET HYPERSPACE
Figure 1-1
The coin mechanism on the front mid-portion of the game cabinet, below the control panel, initiates the play. The cash box is located behind a locked access door.
B. GAME INSPECTION Your new Orbit game is manufactured ready to play immediately after removal from the shipping carton. Your cooperation is desired in order to supply the final touch of quality control to your game. Therefore, please follow the procedures below to ensure that your game is in perfect condition:
- Examine all external parts of the game cabinet for dents, chips, or broken parts.
- After determining that the game has been received in good condition, unlock and open the access door located to the right of the cabinet while facing the coin door, just under the table top. Carefully inspect the interior and verify the following: a. All plug-in connectors are firmly seated. . Remove game PCB as instructed in steps 1-4 of Section E. c. All integrated circuit packages (chips, ICs) in sockets on the game printed circuit board are firmly seated. d. Replace game PCB as instructed in step 6 of Section E. e. The fuses are all seated snugly in their holders. f. No harness wires are disconnected.
1-2 ORBIT Orbit Control Panel
g. No loose foreign objects should be present, especially metal objects that could cause electrical problems.
Be sure all the major assemblies are checked. Check the game printed circuit board (PCB), the transformer (located on the power supply chassis inside the game cabinet), the speaker, and player controls. Also, be certain that the TV monitor is securely mounted.
Check the serial number located on the metallic label in the upper left-hand corner on the back of the game cabinet or the opposite side of the coin door side. The serial number also appears in the corner (common to both edge connectors) on the back of the PCB, inside the game cabinet. See the illustration on the inside front cover of this manual.
C. INSTALLATION
REQUIREMENTS
Voltage Selection Your Orbit game is shipped for operation at 110 VAC, 60 Hz.
IF YOUR LOCAL LINE VOLTAGE IS 110 VAC, perform the following steps:
- Measure AC line voltage with an AC voltmeter as in Figure 1-3.
LINE VOLTAGE-CHANGING VOLTAGE PLUG WIRE COLOR BLACK ORANGE installed at factor GREEN 110 VAC
210 VAC 220 VAC
ORANGE CONNECTOR (FACTORY- INSTALLED)
ON/OFF AND CI INTERLOCK SWITCH
Co be 3 Amp. 250 V. Siow - blow
Figure 1-2
- If AC line voltage is consistently below 100 VAC, plug in the black low-voltage connection, on the power supply chassis. See Figure 1-2.
- If AC line voltage is approximately 110 VAC, plug in the orange connection (factory installed).
IF YOUR LOCAL LINE VOLTAGE IS NOT 110 VAC, BUT INSTEAD IS 220 VAC, perform the following steps:
- Measure AC line voltage with an AC voltmeter as in Figure 1-3.
- If AC line voltage is consistently below 210 VAC, plug in the green low-voltage connection. See Figure 1-2.
- If AC line voltage is approximately 220 VAC, plug in the red connection. POWER SUPPLY CHASSIS 8 Amp. 125V. VOLTAGE SELECTION Fast-Blow CONNECTOR
2.5 Amp .125 V. Slow— blow
Voltage Selection Connectors
Type of Power Cord Atari has added a strain-relief cord to your Orbit game. The advantage of this type of cord is that if pulled accidentally, the strain-relief will hold the cord in place at the cabinet wall. The plastic strain relief “cushions” the impact of the shock and prevents the c.rd from pulling the wires out of the harness connector.
D. INTERLOCK, POWER
ON / OFF SWITCH AND OTHER OPERATOR CONTROLS To minimize the hazard of electrical shock while you are working on the inside of the game cabinet, two interlock switches have been installed. One is located behind
ORBIT 1-3
RANGE SWITCH ‘SET TO 500 VOLTS AC
se yOC ‘AC OUTLET
(152 CENTIMETERS)
Figure 1-3 AC Line Voltage Check
the rear access door and one behind the coin door. These switches remove all the AC line power from the game circuitry while the doors remain open. To help conserve energy, a power on/off switch has been placed on the game so that it can be turned off during closed periods. This switch is located in the upper rear left-hand corner of the game cabinet, as shown in Figure 1-5.
Table 1-1 Installation Requirements
Power Requirements Power Supply: 200 Watts 110 VAC @60 Hz 220 VAC @50 Hz
No lower than 0 degrees Celsius (32 degrees Fahrenheit) Temperature Range On Location and In Storage No higher than 49 degrees Celsius (120 degrees Fahrenheit) Humidity Range
Relative No more than 95%
Humidy Location Space Requirements Height 152 centimeters (60 inches} Width: 64 centimeters (251% inches)
Depth 76 cemimeters (30 inches)
TV Monitor 23-inch Black and White
1-4 ORBIT Figure 1-4 Location Set-up Requirements
Interlock Switch Checkout Procedure Check for proper operation of the Interlock switches by performing the following steps:
- Unlock and open the rear access door and the coin door.
- Plug the AC line power cord into your local AC outlet (110 VAC or 220 VAC)
- Set the power On/Off switch to the “On” position.
- Close the access and coin door. Within approximately 30 seconds after closing the last door to the game cabinet the TV monitor should display a picture.
- Slowly open either door to the game cabinet, and the TV picture should disappear when either the access door or coin door is opened to approximately one inch.
- If the results of step 5 are satisfactory, the interlock switches are operating properly. If the picture does not disappear as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the “On” position
- Close and lock botin doors
BACK SIDE
POWER ONIOFF. SWITCH
Figure 1-5 Location of Interlock and Power On/Off Switches
DIP OPTION SWITHCES
RF SHIELD
=
GAME PCB
Ya” TURN FASTENERS
Figure 1-6 Option DIP Switches and Game PCB Location and Removal
ORBIT 1-5
E. OPERATOR OPTIONS
The operator options offer maximum player appeal for your game location(s). These options are listed in Table 1-2. They are preset for a certain game set-up during production. To determine how the switches have been set for your game, compare the attract mode (Chapter 2, Section B) with the information in Table 1-2.
To change the toggle positions of the switch assembly and set the desired options, the printed circuit board (PCB) must be removed according to the following procedures:
This game includes a new style of easy-access PCB. The radio frequency shield has been redesigned to use only three individual quarter-turn fasteners as a direct result of field input.
- Switch the game power on/off switch to “off” and open the access door.
- Locate the radio frequency (RF) shield assembly immediately inside the game cabinet behind the access door (see Figure 1-6). This assembly is an aluminum box with hundreds of holes. On one end of the assembly is a small PCB with an edge connector coming from the edge of the Football game PCB.
- Turn the three individual quarter-turn fasteners on the RF shield PCB ¥/a-turn to the left or counter -clockwise.
Figure 1-7
1-6 ORBIT
- Carefully pull out the Orbit game PCB and the RF shield board together as a unit. These would not normally need to be separated when merely making option switch changes.
- Set the switches for the desired options as listed in Table 1-2.
- Replace both PCBs by following steps 1 through 4 in reverse order. Do not force or bend the game PCB. Before replacing, inspect the PCB for damage.
- Close and lock the access door.
- Plug in the game and verify that all options function by playing the game.
F. SELF-TEST PROCEDURE
Orbit will test itself and provide data to demonstrate that the game's circuitry and controls are working properly. This procedure uses the TV monitor and the speaker; no additional equipment is required. See Figure 1-7 for location of the Self-Test switch. To start the procedure, slide this switch to “on” as indicated in the figure. See Table 1-3 for further details and instructions on the Self -Test. We suggest that you run the Self-Test each time the coin box is opened.
G. VOLUME CONTROL
If volume is incorrect for your location, open the coin door and adjust the volume control as indicated in Figure 1-7.
SELF-TEST SWITCH
VOLUME CONTROL
Location of Self-Test Switch and Volume Control
Table 1-2 8-Toggle DIP Option Settings
Switch Settings on 8-Toggle DIP Switch (Located on the Game PCB)
Result
| 1 | 2 | 38 | 4 | 5 | 6 |
| ON | ON | ON | 0:30 min. | ||
| OFF ON | ON | 1:00 min. | |||
| ON | OFF | ON | 1:30 mins | ||
| Game | OFF OFF | ON | 2:00 mins | ||
| Length | ON | ON | OFF | 2:30 mins. | |
| OFF ON | OFF | 3:00 mins | |||
| ON | OFF | OFF | 3:30 mins | ||
| OFF OFF | OFF | 4:00 mins | |||
| Game Instruction | OFF OFF | German | |||
| Language | OFF ON | French | |||
| (as displayed | ON OFF | Spanish | |||
| on TV screen) | ON ON | English |
ON Coins Free Play OFF Free Play
ORBIT 1-7
Table 1-3 Self-Test Procedure
Be sure all toggles on the 4-toggle DIP switch are set at OFF. Otherwise the self-test will not function as described below. RESULTIFTESTPASSES [| __—RESULTIFTeSTFALS |
Not Applicable Not Applicable
- Preliminary Remove ORBIT PCB from RF cage as explained in subsection E procedure Steps 14
Set volume level potentiometer (located on the Dual Audio Amplifier PCB as ilustrated in Figure 1-7) to one-half volume
Audio” Low tone indates a bad RAM Zero Page RAM Test Audio Indicator: Set self-test slide switch (located on the } 2 high ones {high tone good indication) Dual Audio Amplifier PCB as Mustrated in Figure 1-7) to the “ON Video Indicator: Position. Screen displays sll H's ‘The bad RAI 's isolated as follows
Lighted LED
RAM Location
Low Note
Heat Reset Hyperspace
Audio Indicator Audio. Any Jow tone of the eight tones in Gicates @ bad dispiay RAM device
The bad RAM is wolated as follows Display RAM Test Occurs shortly after Test 2 & high tones thigh tone good indication}
CONDITIONS Test 3 must pass to insure a valid test elsewhere. Video Indicator Screen flashes, once more displays all H’s Low Note Bad RAM Device Location
- ROM Test Video Indicator: Occurs shortly ater Test 3 and all H's disappeat from screen Scwen displays graphics test pattern Video Abad checksum is indicated by one or more numbers appearing on the screen at the checksum output location Checksum
Switch Number
Checksum Possible Bad Number Devices
H3I2K « 8) or H2&L2(1K x 4 each) Graphics Test syreet H(2K x8) on HI&LI(IK x4 each) K/L3i2K x 8) of M2&F2c1K x4 each} K/L3(2K xB) oF MI&FI(IK x4 each LéMB(2K 8) or N2&E2(1K ¥ 4 each} Lo MB(2K xB) or NISEL(1KE4 each) Pattern
Audio interleave Test Pattern 6
Checksum good when “OK” is displayed in the checksum screen location
Audio
No beep. indicates possible bad switch. Sound/Suitch Test Hoids over from Test 4 Screen remains also as in Test 4 Audio Indicator: Pressing any game select button or game reset produces atone The number oi the game switch will appear on the screen (Exception: Game reset displays an A} Hear reset turns on the explosion and warn ing sounds All other swuiches and option game PCB switches produce a beep on a transition from on to off or vise versa No explosion or warning sound. Sound generator cr dual audio ampiiier PCB cir cxitty possibly bad
Video
Switch pressed, does not display correspond: ing number on screen. Switch oF logic possibly bad Video Indicator
Pressing any game selection or option switch produces a numerical representation of that switch Pressing Game Reser displays an ‘A” rather than a number
1-8 ORBIT
~ vy ORBIT
SELECT GAME
POWER-UP OR FRiEZE MODE AFTER GAME RESET PRESSED aa 1 . —.
Figure 2-1 Atirvci Mode Figure 2-4 Ready-To-Play Mode
+
END OF (ME bo | INITIATED IMMEDIATELY . AFTER PRESSING THE Figure 2-2) F SELECTED GAME (0-9) |
Figure 2-5 Play Mode
INSERT COINS SELECT GAME
AFTER COINS ACCEPTED
Figure 2-2 Ready-To-Play Mode
he nm ORBIT
LEFT PLAYER |
SPACE STATION
RIGHT PLAYER STARSHIP
EXPLOSION
STARFIELD
STAR
LEFT: PLAYER RIGHT
STARSHIP PLAYER
SPACE SHELL FIRE ASTEROID STATION
Figure 2-6 Playfield and Motion Object Display
ORBIT 2-3
Table 2-1 PLAYER CONTROLS
Control Name Description/Function Figure 2-7 Reference | __ Number
i Left player LEFT control
Left player RIGHT control
Left player Thrust control
Left player FIRE control
Left player HYPERSPACE control
Right player LEFT control
Right player RIGHT control
Right player Thrust control
Right player FIRE control
Right player HYPERSPACE control
GAME SELECT
HEAT RESET Rotates left player starship counterclockwise.
Rotates left player starship clockwise.
Applies forward thrust
Fires one shot each time pushbutton is pressed.
Left player starship disappears and then reappears in another spot on the TV monitor screen when pushbutton is pressed. Starship is capable of firing while in hyperspace (invisible) from the position last visible.
Rotates right player starship counterclockwise.
Rotates right player starship clockwise.
Applies forward thrust
Fires one shot each time pushbutton is pressed.
Right player starship disappears and then reappears in another spot on the TV monitor screen when pushbutton is pressed. Starship is capable of firing while in hyperspace (invisible) from the position last visible.
Sets game mode to Ready-to-Play mode as illustrated in Figure 2-4 .
Resets the game to initial play positions.
All pushbutton switch non-lighted LICON types, press for “on” condition, release for “off”.
2-4 ORBIT
Table 2-2. GAME LEVELS
Figure 2-7 Reference Game Level Level Options Letter
| A | BEGINNER | Slow | (Starship and Shells) |
Instant start/stop when pressing forward Medium (Starship and Shells) Fast (Starship and Shells)
B INTERMEDIATE
| Accelerates to full speed when forward push- | Slow | (Starship and Shells} |
| button pressed. Partial breaking when forward | Fast | (Starship and Shells) |
pushbutton released.
Cc EXPERT
Acceleration to full speed when forward push- Fast shells (Shells only) button pressed. Slow — (Starship and Shells) Medium (Starship and Shells) Fast (Starship and Shells)
D SUPER EXPERT Same as Expert, with a strong gravity option.
Figure 2-7 Location of Game Levels and Starship Controls
ORBIT 2-5
Table 2-3 GAME OPTIONS
Figure 2-8 Reference . nt, a Number | _Game Option. _ Description/Function
| i | Bounce Back | Sets boundaries around perimeter of the TV |
(See Figure 2-9) monitor screen. Example: Starship immediately reverses direction after reaching boundary. Normally perimeter boundaries do not exist
| 2 | Negative Gravity | Sun radiates gravity outward to perimeter |
| (See Figure 2.9) boundaries of the TV monitor screen. Normal sun state radiates positive gravity (positive gravity is inward toward the sun)
| 3 | Zero Gravity | Sun does not radiate gravity. |
| 4 | Black Hole | Invisible sun with any selected gravity. |
(See Figure 2-9)
| 5 | Space Stations | Two space stations orbit around sun. Each |
(See Figure 2-7) player is designated a specific space station on which he may land for repairs, fuel and shells. When player starship touches opponent's station it is immediate annihilation.
| 6 | Unlimited Supplies | Unlimited fuel and ordnance (fire power) |
| 7 | Stars (See Figure 2-7) | Remove stars from playfield. |
Strong Gravity Unusually strong positive gravity.
Figure 2-8 Location of Game Option Pushbuttons
2-6 ORBIT
BOUNCE BACK GAME OPTION (STARSHIP HITS BOUNDARY AND IMMEDIATELY REVERSES DIREC- TION) TV MONITOR BOUNDARY BLACKHOLE NO SUN
POSITIVE GRAVITY
NEGATIVE GRAVITY
BACK HALE FRONT HALF OF LEFT OF LEFT PLAYER ala STARSHI
STARSHIP P
WRAP AROUND NO BOUNDARIES (THE OPPOSITE OF GAME OPTION, BOUNCE BACK)
Figure 2-9 Selected Game Options
ORBIT 2.7
INITIAL AMOUNT OF: SHELLS. ONE SHELL INITIAL AMOUNT OF FUEL. FUEL IS EXPENDED WHENEVER RIGHT, LEFT OR FORWARD PUSHBUTTONS ARE PRESSED
FLASHES WHEN FUEL REACHES TOP PORTION TV SCREEN
WHEN SHELLS REMAINING REACH 5 TV SCREEN SHELLS REMAIN (00)
FLASHES WHEN FUEL QUANTITY REACHES 20
NORMALLY INDICATES AN ANNIHILATED STARSHIP, OR A STARSHIP MOTIONLESS AND DEFENSELESS—ONLY SALVATION (S TO BE PULLED IN BY GRAVITY
TOWARD A SPACE STATION IF IN
PATH; OTHERWISE, A HEAT RESET SHOULD BE USED.
TOP PORTION
TV SCREEN
SCORE DISPLAYED FOR 5 SECONDS AFTER A GAME IS SELECTED OR RESET (AUTOMATICALLY OR MANUALLY WITH HEAT RESET) Fuel is also used in very large amount to enter hyperspace
Figure 2-10 Score and Data Display Portion of TV Screen
2-8 ORBIT
THEORY OF OPERATION
A. GENERAL INFORMATION
This chapter provides a general overview of the theory of operation of the Orbit electronics contained on the game printed circuit board (PCB). It also goes into specific detail of the various circuits to explain to an individual of moderate technical background how these circuits should perform. This detailed information has been organized with emphasis placed on troubleshooting the game PCB, circuit by circuit.
The Orbit game block diagram of Figure 3-1 illustrates the major components, including all controls remote to the game PCB. The function and direction of the information to and from these various controls is also shown.
ORBIT
TVMONITOR — (INTERLACE)
HORIZONTAL DEFLECTION f
intenLock Ac POWER \ swirce CONTROL cIRCUITAY
scsounce wtenioex La _
SWITCH
GAMES, AND OPTION LICON PUSHBUTTON ‘SWITCHES.
GAME PRINTED. circuit
SPEAKEA1 AUDIOT
UAL AUDIO AMPLIFIER Pee SPEAKER?
BRACKET LOCATED BEHIND THE COIN DOOR (REFER TO FIGURE 1-7)
Figure 3-1 Orbit Game Block Diagram
3-2 ORBIT
SYNCSIONALS. Gomesnc
wioeo Sunmins toure NETWORK
ORBIT 3-3 Figure 3-2 Orbit PCB Block Diagram
The Orbit PCB block diagram in Figure 3-2 illustrates the division and function of the various circuits located on the game PCB and how they are controlled by the microprocessor. Refer to Figure 3-2 as you go through the following circuit descriptions.
The functional operation of the Orbit PCB circuitry begins naturally enough with the microprocessor (or MPU) circuitry. As you go through the various circuit descriptions, you Jearn how the MPU receives its sequential program instructions from its ROM memory and how it carries out these instructions through the use of its display RAM memory (Section C); how it reads in the game control switches (Section G), and how it writes or outputs the results of its instructions and calculations to the game’s other PCB circuitry, such as the playfield generator (Section E), the motion object generator (Section F), and the audio amplifier (Section K).
A circuit description of the standard Atari sync generator (Section D) is also included. This is the only PCB circuitry that functions independently of microprocessor control.
All reference schematic diagrams of the aforementioned circuits are found in Appendix A at the end of this manual.
B. POWER SUPPLY (See Figure 3-3) The power supply produces all the necessary game voltage requirements as shown in Figure 3-4.
The PCB receives +10 volts DC, unregulated, at pins B and 2 of the game PCB edge connector and from the secondary of the transformer located on the Type B power supply chassis.
The +10 volts is rectified and filtered off-board and regulated on-board by the LM323 three-terminal regulator device to astable +5 volts DC. The +5 volts DC is distributed throughout the PCB to power all logic circuits.
Cc. MICROPROCESSOR CIRCUITRY The heart of the Orbit game PCB is the microprocessor circuitry. A brief description of the major components and their function within the microprocessor circuitry is provided in the following paragraphs. Note that the microprocessor circuitry components include the following: (see Figure 3-5)
3-4 ORBIT
- MPU (at location C3)
- Data Buffers (Tranceiver devices located at E4 and E6)
- Address Buffers (Schmidt gate devices located at B4 and C2)
- Program Memory; comprised of PROM device N2, N1, M2, M1, L2,L1, £2, £1, F2, Fl, H2 and H1, for the -01 version; and ROM devices L/M3, K/L3, and H3 for the -02 version. (See Figure 3-5)
- Working RAM devices located at C1 and D1
- Address decoding devices (A5, A6 and miscellaneous gates)
- Watchdog reset counter (K10 and miscellaneous gates)
MPU, ROM, and RAM (See Figure 3-6) The microprocessor is the “master controller” behind all action that takes place in the game circuitry. In going through the following paragraphs refer to Table 3-1, MPU Input/Output Signa! Descriptions. Upon initialization, the MPU (via ABUS O-ABUS 15) addresses data permanently stored in the program ROMs or PROMs. This addressed data then travels to the MPU via its 8-bit data bus (DO through D7). The MPU decodes this data to determine what action it is to perform next (i.e., “read coin switch 1,” “attract mode”, etc.). The MPU uses RAM memory to perform many of these instructions, namely to temporarily store information which it will later recall. The MPU is capable of writing (or putting data into) the RAM and then later reading (pulling data out of) the RAM, via its address bus (ABUS 0-ABUS 15) and bidirectional data bus (DO-D7).
Address Decoding (See Figure 3-7) The MPU address decoding circuitry performs the critical function of turning on or enabling the appropriate game circuitry (i.e., RAM, ROM, latches, etc.) at the appropriate time, so that information can be transferred back and forth between this game circuitry and the MPU. A memory map defining the address decoding circuit is shown in Table 3-2 as reference.
® 2 Clock Driver
The basic operating frequency of the microprocessor is established by its @1 and 2 input (on pin 37 of the MPU device). The Orbit MPU runs at an operating frequency of 750 KHz. Examination of the MPU © 2 output waveform (pin 39) with an oscilloscope should show a signal with a period of 1.33 microseconds. (The period of any periodic waveform is the measurement of the time
R104
(-01 VERSION)
R37
4n,10w (02 VERSION)
+ 10V(UNREG) [8 [2 | R1, 4,9, 14, 19, 20, 25
Ri, 2,6,9, 11, 12, 13, 18, 30 1K (PULLUP)
+5V
C1-9, 11-19, 22-25, 28-32, 34-42, 44-46, 48-50, 53, 54, 62 T .1(BY PASS) I
Figure 3-3 On-Board Power Supply Schematic Diagram
+10 VD (UNREG!
AC SOURCE POWER ~ ‘SUPPLY CHASSIS: | TYPE B 1c ULATED)
GAME PCB POWER ‘SUPPLY REGULATOR CIRCUITS
Figure 3-4 Power Supply Simplified Block Diagram
it takes to complete one full cycle.) The 750 KHz clock outputs are generated by the 4H signal. This 4H frequency is generated by the horizontal sync counter R4 to produce the @ 1 and 2 clock input. See Figure 3-8. 1 and 2 Clock Driver Signal. Watchdog RESET (See Figure 3-5)
The reset counter in the microprocessor control circuitry consists of a 4-bit decade counter, K10. The Q, output of this counter is the RESET signal to the MPU
ORBIT 3-5
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ETHEROR
froma ‘BROW PROGRAN Memory CPaom ones) ‘| VERSION roweu rs cutee ROM PROGRAW MewoRy (ROM CHIPS) (£2 VERSION
A) PROGRAM MEMORY “
ROM PLAYFIELD DATA err MUX
oRaPHICS: To vibeo. PROM GENERATOR MEMORY incurtay (poms tos (aicr.07 NccoUNTER cn AND RELATED. cacUITRY Creu mane By GRAPHICS MEMORY
puaypieus ADDRESS Bits
ISYNCIADDRESS) FART
eauses FROM MPU |
puss? raw (scm) peoos.ey wis.26 DATA TUB. Ks HU. 6
pro 47. 1246,2028, aa
te) orsPLay pam (READIWRITE| MEMORY
f
FROM MPU
O}WoRKinG. (REACIWRITE) MEM ORY
FROM MPU
acon. NUMERICS To woeo PROM ar) ry SUMMING [AND RELATED cincur eracuiray
Figure 3-6 Memory Block Diagram
ORBIT 3-7
ABUS I!
ABUSIO —
dbus 4 Abus a 23),
AS
DE CODER/ DEMUXER, AMR
——- RAMWR,
ABusio
Agus?
| Roms Boe Aguse | nowt
TP DISPLAY)
BUAYFIELD SEL e-Nwoucnwos Ao Lsaz DECODER,
j—— WARNING
R28 —— WOTEAMPLD
WOTELD
R29 HYPER LEDS 150) a2, 2343,
fli] paner srmone
Pry ‘ye S00, PANEL BUS OC
R30 ABUS3~ 7 Az
ABUS2 — os|® ass, —ad go —s9: x IN3643
RS [c]HEAT Ret LED 150)
+10¥ T unree ry
i 1 co F |CocnouT
Figure 3-7 Address Decoding
4H
o2 in 750KHz
(1 CYCLE) >
LS arcs pine
4 | | c3PINe
C3 PIN 37
3-8 ORBIT Figure 3-8 1 and @2 Clock Driver Signal
Table 3-1 MPU Input/Output Signal Descriptions
Description/Function
These eight lines are bi-directional data bus lines
These sixteen lines are unilateral MPU address lines to supporting memory {ie.. ROMs. RAMs), and I/O.
This input line. when low. resets the MPU from either a power-down or on a QE output of the watchdog counter. During the reset sequence prior to RESET going high. the contents of the last two locations (FFFE, FFFF) in memory are loaded into the MPU program counter to point the start of a reset routine
This input when low indicates an interrupt request to the MPU. After the MPU concludes its current sequence it will then proceed to the IRQ sequence
This input line while going low indicates a non-maskable interrupt sequence. After the MPU concludes its current sequence it will then proceed to the NMI sequence Number Signal of Lines
D0-D7 8
A0-AIS 16
RESET 1
ikQ i
NMI 1
DBE 1
01, 62 2
R/W 1 This input line when high enables the MPU tri-state bus drivers, It is driven by the 2 clock Two-phase, non-overlapping MPU clock inputs.
This output is the read and write signal line which indicates the direction of data transfers on MPU data bus.
Counter K10 counts how many times the 128V signal changes states. On every high-to-low transition of 128V, the counter advances to the next count in its sequence. Meanwhile, the TIMER RESET signal, generated by the MPU at various times during its normal instruction sequence, is resetting the counter back to zero. If for some reason the MPU program tas strayed from its intended instruction sequence and the TIMER RESET signal does not occur before this counter counts up to a point where the Q,, output goes high, a RESET signal is generated to the MPU. The RESET signal causes the MPU to restart its instruction sequence from the beginning of the program.
D. SYNC GENERATOR (See Figure 3-9) The base frequency of the sync generator is a 12.096-MHz clock, generated by a crystal-controlled oscillator consisting of crystal Y1, inverter R3 and several discrete components. The output of this oscillator is 12 MHz. Examination of this signal with an oscilloscope (at pin 4 of R3) should show the period (or cycle time) to be approximately 83 nanoseconds (.083 microseconds). See Figure 3-10.
This base frequency is then divided down by binary counters R4, R5, R6: it provides the various horizontal synchronization frequencies (1H through 256H). The final output of this horizontal counter chain is 256H (at pin 13 of R6). This signal is in effect a division of the base frequency {12.096 MHz) by 768, to give a horizontal line frequency of 15,750 Hz. The period of 256H is about 63.5 microseconds. The 256H signal, as well as other horizontal signals, are used to generate the H SYNC timing pulses at flip-flop F8. See Figure-3-10, Horizontal Sync Timing Diagram for the relative timing of these waveforms.
The H SYNC signal is used to clock two stages of vertical sync counters P7 and P8. This H SYNC signal is divided down by these counters to form the various vertical synchronization frequencies (1V through 128V). These two stages of vertical counters are used, in effect, to do a divide by 262 of the H SYNC signal. This results in the final output of these counters (128V at pin 11 of P8) to be a signal at a frequency of 60 Hz (the period is approximately 16.6 milliseconds). The various vertical frequencies address a sync PROM (P6) whose output data is latched by latch N6. The outputs of this latch are the various polarities and phases of the vertical timing frequency used to synchronize the TV monitor display. These signals all run at a frequency of 60 Hz. Figure 3-12, Vertical Syne Timing Diagram, for the relative timing of these waveforms.
ORBIT 3-9
Table 3-2 Atari Programmed Memory Map
MEMORY MAP ADDRESS [Recoeciwa [bla shale bdessfo ess]
| ‘D500 | {[e[6[6]o|e [|e io alalAlala | x | |||||
| ‘0800 | nog | @ | | | INO8 | |||
| OCce | a | RI | NOT USED | ||||
| a | Bede | 5 | TR | THRUST 2 | |||
| lelph | oO | al | |||||
| maigecon | * | R | |||||
| ~_lletgfelati | le | iz | |||||
| A | ° | R | |||||
| 2 | {aleiali | [2 | Rl | ng | |||
| 7 | OoOCuOu | | | 8 | ele | |||
| |jo00- | etale’ | | oon | Alla|*|olole| | 6 | ||||
| olelel: a! | oI | llr ale | ele | [io | |||
| = | sialolitel | ole | fo | [RY | 4 | . | THRUST 1 |
| Orn | I | \e | o | ROT Bt | = | ||
| ..fo[sfon | iS | Db | ROT At | _ | |||
| oon | Al | e | HYPERT | ||||
| _— | Bon | ial | aie|+|+)| TRIG 1 SW | ||||
| He | ate | aig | a |
[elol a i plpaln| ‘OPTION SW. OPTION SW. :
| ‘OPTION SW | m= | i |
‘OPTION SW | eer aa
lelelslels o'ele’s un pl ininia > alperip
“PICTURE — “POS —_HPOS - NORMAL WIDTH FULL OBJECT TOP HALF _ BOTTOM HALF = 9, izziziz| Coes aca
| [3800 | airy | 'S bo /D]|_NOTELD | = | ||
| 3900 | | | \ | >/>|DIDI|_NOISEAMPLD. | _ | |
| 3A00 | fe | 'b [D|D/0|| NOTEAMPLD. | = | : | |
| 3000. | Bile | ¥)D|Dib || PANEL BUS LO (WRITES SBX LINES) | |||
| '3C00 | Bll | slelele|| | NOT USED | 4 | |
| 302 | Dil | tlelele | —SEEGIONTT | ||
| ‘3Go4 | tg | elelels | OFF) | ||
| 308 | Bit | elele|+l| | PANEL BUS OC | a | = |
| '3COA | Dil | ~_-PANEL STROBE | OFFOVONC)— |
ih falas beh |i fal
| The | = | ARREST, | . | a |
| Cfifele | ° | TIMER RESET | Tr |
IAIATA! AA[A| alalala||e |[b[D| BIDID/p|b ID || ROM T _
| AMARA AA lala te BS [DBO DipiL ROM 2 | —- | - |
AiAalA/AIAAIALATAII|S {Dib iDIBibIB|L ROM 3 = AJAIAIATAIAlAlAlAl|@/[d(D [>/B/b/D/D[bi] ROM 4
3-10 ORBIT
P.R9 PAZ P.RI2 cro
PAS Re 330 PO P12 PS PE
cep na RS 83 “ Ro 83 ceT 931g = 7 ceT gsi Te 9316 SNS (It pes 02 cp BINCNTR BINCNTR BIN CNTR of 1 ‘08 or Qo at a2 a3 MR Qo 01 02 a3 MR
12.096 MHz 2564
oun
1" 2H
aH
8H 16H aH SYNC PRs
sapere zz an —"PDo— an as ba
Pio 24 —So— 2H P10 ov —So— sev VAESET
Fo pr Pa Pa Pt Pre Pr Pe
9316 9316 BINCNTR BIN CNTR 2H
av
av ev
sv
av wav
Figure 3-9 Sync Generator Schematic Diagram
ORBIT 3-11
for appropriate designation diagrams in Appendix A of pin numbers. Refer to the Schemati
VERTICAL S¥NC
HORIZONTAL SYNC PULSES muses
CRYSTAL, 12.096 MHz (Y1) {ot cRYSTAL HORIZONTAL CONTROLLED sve ee OSCILLATOR counrer CORTE VERTICAL
SYNC
(na) (ha, RS, RB) SIGNAL COUNTERS
V BLANK V RESET
MULTIPLEXER
‘COMPSYNC
itry ‘ircui Controlled Oscillator and TV Sync Cii 10 Simplified Diagram of Crystal. Figure 3-
3-12 ORBIT
128H ————————— 63.5 MILLISECONDS —________»|
256H PLAYFIELD DISPLAY
Hsync ———MM
Figure 3-11 Horizontal Sync Timing Diagram
LINE NUMBER 239) 240 260 | 261
VBLANK
VRESET
COMPSYNC
HSYNC. PULSES EQP1 PULSES
- EVEN FIELD IF SIGNAL =
LINE NUMBER 242 | 243
VBLANK J 4
VRESET /
- ODD FIELD IF SIGNAL =
Figure 3-12 Vertical Sync Timing Diagram (Interlaced)
ORBIT 3-13
The end result of the horizontal and vertical timing waveforms is to synchronize the TV monitor display. This display consists of 262 horizontal lines per frame, with each line being the time equivalent of 768 12 MHz clock pulses. Each frame is repeated 60 times per second, providing the necessary frequency of display refresh that provides a stable non-flickering display.
E. ALPHANUMERIC /PLAYFIELD GENERATOR
(See Figure 3-13) Alpha and numeric characters are displayed as 8 line by 8 bit blocks of video at the scoreboard display area of the TV monitor screen. These alphanumeric characters are stored in PROM A7 (see Figure 3-14) which is accessed by addressing the data from the RAM (L4, K4, H/J4, F4, L6, K6, H/J6, F6). The microprocessor loads the alphanumeric character code into the RAM. These RAM data bits (PFD-xx) are then multiplexed out to the 8-bit PFO-PF7 data input to latch C6. The latch output bits then address the alphanumerics PROM A7 (at address inputs A3-A8) and address one of the 64 dif ferent pictures stored in it. The vertical signals (4V, 2V, 1V) and the vertical reflect control signal (SCRNRFL) determine which of the 8 lines of the character is currently being addressed.
The data bits GDO-GD7 from the PROM are then multiplexed by devices B8 and C8. Then converted into a serial bit structure via parallel to serial shift register D8. The output of D8 is the alphanumerics video labeled RAWVID.
This circuitry functions as follows:
- When horizontal sync pluse 4H is low, the MPU buffered address bus (ABUS 0-ABUS 15) addresses various playfield display RAM locations, and writes appropriate picture codes into them via the MPU data bus (DO-D7).
- When 4H is high, horizontal sync signals (8H, 16H, 32H, 64H) and vertical sync signals (8V, 16V, 32V, 64V) are now allowed to address this game display RAM and read data out of it. This data (PFDO-32)
64,8 IT ALPHA AND NUMERIC wl GuanacTens FROM DISPLAY RAM
VERTHORIZ
REFLECT BITS To PLAYFIELD ‘VARIABLE DELAY SHIFT REGISTER PARALLEL bo eis. SERIAL ‘CONVERTER
Figure 3-13 Alphanumerics Generator Block Diagram
3-14 ORBIT
‘ = (etal TS02 256H ALPHANUMERICS
PROM. DATA BITS FROM DispLay | PICA
RAM VIA 1c3
LATCH C6
VERTICAL
POSITION
BITS
a wreruecr err
> TO MOTION |) Obuecr
GENERATOR
| ano video | ciRcurrs FQUIVALENT BLOCK DIAGRAM al
BITS
REFLECT HORIZONTAL PARALLEL REGISTER
Figure 3-14 Alphanumerics Generator Simplified Schematic Diagram
ORBIT 3-15
being read out is then re-multiplexed into data bits PFO-PF7. These 8 data bits are then latched by latch C6 and labeled PIC 0 through PIC 7.
Since the data was read out of the RAM by the horizontal and vertical sync signals, the picture codes PIC 0-7 always correspond to the portion of the monitor display currently being scanned. Because of this, the PIC 0-7 outputs can be used to generate video information for immediate display. These PIC signals address one of 64 8 x 8 pictures stored in graphics. The output of the PROMs is then converted to serial video information by shift register D8.
F. MOTION OBJECT GENERATOR
(See Figure 3-15)
The motion object generator produces motion objects such as the starships, shells, space stations and asteriod. These motion objects are generated by some of the same circuitry found in the alphanumeric generator (see Figure 3-14), while the actual graphics are permanently stored in PROMs B/C7 and D7 (see Figure 3-17). The
3-16 ORBIT RAWVID signal from the parallel to serial shift register D8 is connected to OR gate M8. This gate ORs the raw video (RAWVID) from the play ield circuitry and the data out (DO) from the RAM L8 {right player starship) which is also called the motion object video. This is then gated by AND gate M7. When 256H*" is high, the M7 output is sent to the data input (Din) of the RAM L8. When 256H** is low the output of M7 (pin 8) is low. This low input to RAM L8, pin 13, loads the RAM with zeros (clears the memory) at the selected addresses.
The RAM address is selected by the microprocessor and latched at J7 via the display RAM. The playfield data from the RAM display (PF16-23) is loaded (HLD) into binary counters K7 and J8 which presets the counter to the horizontal position of the motion object. These couniers then count at a 6MHz rate until the clear (HCLR) signal goes low during active video (256H). The outputs of the counters then address the RAM. This RAM will either write (WE low) the serial data at DIN (pin
- in the addressed memory or read the serial data at DO (pin 6) in the addressed memory.
The motion objects are displayed on the playfield as determined by the logic signals at the J1 latch and the vertical magnitude comparators (H7, H8).
VERTICAL
REFLECT
BIT
03373
NOROM
cst
MOR Dut
2S56H™ Pics. DATA BITS ricd
FROM DISPLAY pies
RAM VIA
LATCH C6
PLAYFIELD AND MOTION OBJECT ROMS 6D7 ——_ > GDS Gps 6Dd Gps Gpz “epi PRD 4K
Gde >|
RAW VIDEO GENERATOR BLOCK REFER TO FIGURE 3-14 FOR DETAIL SCHEMATIC DIAGRAM
-—— Raw vip TO MOTION OBJECT GENERATOR AND VIDEO CIRCUITS
Figure 3-15 Playfield Generator Block Diagram and Simplified Schematic Diagram
ORBIT 3-17
3-18 ORBIT Figure 3-16 Display RAM simplified Schematic Diagram Lig 2€ x 9S¢
VERTICAL MAGNITUDE COMPARATORS.
PLAYFIELO. (MorION OBJECT Vibeo To vioeo sSumiaa cincUTy
ORBIT 3-19 Figure 3-17 Motion Object Generator Block Diagram
To Tv MONITOR, CHASSIS:
Fur TR VBLANce
Figure 3-18 Video Circuit Simplified Schematic Diagram
G. VIDEO OUTPUT
(See Figure 3-18) The video output circuit receives all the video signals (Comp Sync and related signals) and gates these signals summed at pin 6 of the Orbit game PCB as the composite video signal sent to the TV display monitor.
H. AUDIO GENERATOR
(See Figure 3-19) The audio generator circuit produces the roar, explosion and various note sounds. The roar and explosion sounds are the result of the gated random noise generator comprised of shift registers A9 and A10. The volume for these sounds is automatically controlled by
3-20 ORBIT the data bus bits DBUS 0 - 7. These eight bits are split into DBUS 0 - 3 and DBUS 4 - 7 to produce two separate sounds later amplified by the dual amplifier PCB. The amplifier develops the Stereo sound heard by the player.
Each 4-bit sound is then filtered by the active bandpass filter circuit comprised of either one-half of B12 (LM324) or the other half. The outputs of the filter circuit are individually mixed and outputted to the dual amplifier PCB.
The notes are generated by the frequency synthesizer comprised of device J11 and H11. The NOTE output signal level is then split by the gating with the output of E11 latch to develop signal outputs ANOTE 1 and ANOTE 2. These signals are then mixed, ANOTE 1 to audio output 1 and ANOTE 2 to audio output 2.
FROM
MPU
BUFFERED
DATA
BUS
ADDRESS,
DECODER
aH
NOISERST
ANOTE1 FROM NOISEAMPLD ADDRESS
aupIo aupio our oor 1 TO DUAL 1 AND AvoI0 morete 2 VOLUME AMPLIFIER
LeveL Pee CONTROL
AUDIO ouR tot I L—__J ‘Avoio OUTPUT 1AND 2 BANDPASS FILTERS RANDOM NOISE GENERATOR
Figure 3-19 Audio Generator Simplified Schematic Diagram
ORBIT 3-21
INPUT 1
VOLUMECONTROL = 'OK
INPUT 2. 10K Rt 10K +7] outeut 1000uF cu
RS la
CHANNEL 2 AUDIO AMPLIFIER CIRCUIT
Figure 3-20 Dual Audio Amplifier Simplified Schematic Diagram
K. DUAL AUDIO AMPLIFIER
(See Figure 3-20)
This dual audio amplifier for the Orbit game is a PCB assembly which consists of two individual amplifier circuits. These two circuits reproduce the realistic cosmic stereo sounds produced by the game’s sound generator.
3-22, ORBIT The amplifier device of each circuit isa TDA 2002, as illustrated in Figure 3-20 each driving a speaker. The volume level is adjusted by PCB mounted potentiometers R1 and R2.
The power supplied to the circuit orginates from the power supply chassis assembly 25 VAC output.
ADJUSTMENTS
AND
MAINTENANCE
Due to its solid-state electronic circuitry, this Atari unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this mariual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical background.
ORBIT
A. CLEANING
The exteriors of game cabinets and Plexiglas® panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the acrylic plastic panels, because any dust can scratch the surface and result in fogging the plastic.
B. COIN MECHANISM Components On Coin Door Figure 4-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. Powering the game causes the lock-out wires to retract far enough to allow genuine coins to reach the coin box. When AC power to the game has already been turned off, the lock-out coil is de-energized, causing the lock-out wires to move out far enough to divert coins to the return chute.
Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending
SLAM SWITCH ASSEMBLY
LOCK-OUT COIL LAMP HOLDER
Figure 4-1 Coin Door Assembly
4-2. ORBIT out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.
Also shown in the photograph is a slam switch assembly. It has been included to defeat any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.
Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 4-2. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pushing down on a release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 4-3.
Plexiglas® is a registered trademark of Rohm & Haas Company.
Figure 4-2 Hinging Open the Magnet Gate Assembly
Figure 4-3 Removal of Coin Mechanism
Cleaning of Coin Paths
By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.
Figure 4-4 shows the surfaces to clean inside the coin mechanism. These include the inside surface of the
(CLEAN BOTH SURFACES WHERE COIN ENTERS THE MECHANISM, AS WELL AS THE MAGNET)
Figure 4-4 Surfaces to Clean Inside the Coin Mechanism mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.
If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a 3/8-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 4-5). Removing the plate will provide access to the entire channel.
Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.
Figure 4-5 Removal of Plate Covering Rear of Coin Slot
Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 4-6 shows this lubrication point
Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 4-7. Use extreme care when handling or touching these wires.
ORBIT 4-3
MANUALLY HOLD DOWN REJECTION BUTTON AND APPLY ONE DROP HERE
LOCK: OUT WIRE
Figure 4-6 Close-Up View of Lubrication Point
In Figure 4-7 you will note that the coin switch trip wire is oriented into the “V” of the secondary coin chute. The wire should extend to only about 1/8” beyond the chute.
A retaining clip holds the wire onto the switch actuating stud. If you should lose a retaining clip, all is not lost. dust crimp the switch actuating stud over the trip wire with a pair of pliers.
Mechanical Adjustments on Coin Mechanism Coin mechanims are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it toa clean well-lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure 4-8 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by someone who has experience in servicing coin mechanisms and who understands their operation.
44 ORBIT CORRECTLY ADJUSTED TRIP WIRE
Figure 4-7 Detail View of Coin Switch and Trip Wire
General Troubleshooting Hints
The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.
« {TEM IDENTIFICATIONS 1 Kicker and Separator Screws 2 Washers 3 Kicker 4 Separator 5 Gate Lever Spring 6 Gate Pivot Pin 7 Mainplate Assembly washer 9 Rail 10 Gate Assembly 12 Cradle Assembly
13 Upper Gate Pivol Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 17 Retaining Screws 18 Coverpiate Assembly 19 Return Coverplate 20 Coverplate 21 Mounting Studs 22 Lower Gate Pivot Spring 23 Coin Release Lever Kicker and separator 1, Set the acceptor with the back of the unit facing you in the test position.
- Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
- Insert several test coins (both old and new) and note that some are returned by striking the separator. 4, Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw.
- insert the test coins again and, if some are still returned, repeat Step 4 unti! all the coins are accepted.
- Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
- Insert the test coins and note that some are returned.
- Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
- Insert the test coins again and, if some are siill returned, repeat Step 8 until all the coins are accepted. 10, Be sure that both screws are tight after the adjustments have been made.
Magnet gate
- Set the acceptor with the front of the unit facing you in the test position. 2, Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.
- With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
- Test this adjustment using several other coins (both old and new) and. if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted.
- Fix the magnet gate adjusting screw in this position with a drop of glue.
Additiona! Cleaning
- Remove the transfer cradle (12) and the undersize lever (14).
- Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins. 3} Replace the transfer cradle and the undersize lever.
- To be certain the coin mechanism is completely free of any residue. place the mechanism in boiling water for several minutes. Carefully remove it and jet it air-dry completely before reinstalling in the door.
Figure 4-8 Adjustments on Coin Mechanism
ORBIT 4-5
Cc. TV MONITOR
ADJUSTMENTS
For best results be sure the game has been turned on for a while before making any TV monitor adjustments
- NOTE
The TV monitor adjustments are accessible through the rear door panel of the game cabinet. These adjustments have to be done while the game is energized. Therefore, only persons familiar with safety measures and repair procedures on electrical equipment should perform them.
The TV monitor should be adjusted only when the picture is distorted or if the contrast or brightness seems out of adjustment.
The monitor’s adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure 4-9 shows the location of the adjustments on both TV monitors used by Atari. Your game contains a TV monitor manufactured to Atari specifications by either Motorola or TEC Video electronics. When making adjustments, follow these general guidelines:
BRITE (Brightness) —Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up
CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being blurred.
HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal Oscillator) — Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture.
VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture.
D. FUSE REPLACEMENT Orbit contains seven fuses, five on the power supply assembly in the lower part of the cabinet and two on the TV monitor assembly. Power supply fuses are accessible through the access door assembly. TV fuses are also ac-
Cee Cven uw neicw \vear Hous ‘CONTRAST BriGHT> HoRIZ. HOLO. VOLTAGE SWITCH (leave in right position)
MODEL TM- 600/623 ‘conTRAST —) Horiz osc } 2 FUSES~ Remove” Coven To REPLACE (eon 0 8 quien Brew) BRIGHTNESS \rocus
MOTOROLA MODEL M5000/M7000
Figure 4-9 Locations of Adjustments on TV Chassis
46 ORBIT
cessible through the access door. Replace fuses only with the same type as follows:
Wells-Gardner 19V1001/22V1001 Monitors: 3AG 1.5-amp Slo-Blo 3AG 0.75-amp Slo-Blo
TEC TM-600/623 Monitors: 3AG 2-amp and 0.5-amp quick-blow, 250 volts
Motorola M5000/M7000 Monitors: 3AG 0.8-amp quick blow, 250 volts
Power Supply: Fuses Fl and F2—3AG 3-amp slow-blow, 250 volts Fuses F3 and F4-——3AG 2.5-amp slow-blow, 125 volts Fuse F5—3AG 8-amp fast-blow, 125 volts
E. LICON SWITCH REMOVAL (See Figure 4-10) The LED switches on the front panel have a very low failure rate. In case either switch should ever be suspect, first test it. To test the switch perform the following steps:
NORMALLY CLOSED (N.C.) CONTACTS
CONTROL PANEL
‘SWITCH
TURN COUNTERCLOCKWISE TO REMOVE
LIGHT-EMITTING DIODE (LE.D.) CONTACTS:
NORMALLY OPEN (N.O.) CONTACTS.
- Remove all wires trom the suspected switch.
- Turn the switch counterclockwise white holding the cone-shaped nut of the outside of the game cabinet.
- Install a new switch using the reverse procedure,
- Reconnect the harness wires. Unlock and open the coin door. Remove the wires from the suspected switch. Set multimeter to ohms scale. Set ohms scale to R x 1, then zero the meter. Onwnrye Connect muitimeter leads to appropriate LED switch contacts. (See Figure 4-11 for designation of switch contacts and meter lead placement.)
- Check contacts (push and release the switch button) for closed and open continuity.
- If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in Figure 4-10.
F. TV MONITOR REMOVAL (See Figure 4-11)
If the TV monitor proves to be at fault, remove the monitor as shown in Figure 4-11.
DOUBLE-POLE SINGLE-THROW (DPST) SWITCH WITH INTERNAL LED
Figure 4-10 LICON Switch Removal
ORBIT 47
Pons
ao Remove control panel. Unplug connector. Remove playfield Plexiglas shield. Remove cardboard bezel. Unplug TV monitor chassis connector and remove four carriage bolts on TV shelf assembly Remove two eyebolt nuts. Remove TV monitor.
[
48 ORBIT Figure 4-11 T.V. Monitor Removal
ILLUSTRATED PARTS CATALOG
The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for the Orbit game.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this catalog, and serial number of your Orbit game. This wili heip to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproguction” forbiggen without the
SECTION Z=Z
thereon. nor any "ght to rearaduce tmis drawing or any part nereot except for manulacture by vendors of Alar Ineor porated and for manulacture under the corporation's writ fen license. no rigtt 10 repraguce this draming 1s granted or the subject mate: thereo! uniess by writen agreement with oF wetten pertmussios trom tne corporation
Figure 5-1 Orbit Final Assembly A033745-01 D
5-2 ORBIT
2 Reao(S)— = BREGO &)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reprosuction, iyoidaer wimnout Ime Speciic wntter
theres. nor any regnt fo reproduce his Grawing Sr any part thereat. except or marulacture by vendors oi Aiar cer porated and for nanutaciure unce! 1s Grawing Is granted forthe subject malter thereat unless by eriten agieement with gr wrsten permission rom the corbaration
Figure 5-1 Orbit Final Assembly A033745-01 D
ORBIT 5-3
ATARI Figure 5-1 Orbit Final Assembly Parts List
| Item | Part Number | Qty. | Description | |
| 1 | A033744-01 | 1 | Assy., Cabinet with Graphics | |
| 2 | A033747-01 | 1 | Assy., Control Panel | |
| 3 | A008875-01 | a | Assy., T.V. Shelf | |
| 4 | A033750-01 | 1 | Assy., Rear Door | |
| 5 | A030867-01 | 1 | Assy., R.F. Shield Enclosure | |
| 6 | A007197-01 | 1 | Assy., Power Supply Base | |
| 7 | A009083-01 | 1 | Assy., Coin Door | |
| 8 | A0G7902-01 | 1 | Assy., Cash Box | |
| 9 | A033572-O1 | 1 | Assy., R.F. Shield PCB | |
| *10 | A033570-01 | 1 | Assy., P.C. Board, Orbit | (PROM version) |
| ll | A033758-02 | 1 | Assy., Harness and Component | |
| 12 | A033016-01 | L | Assy., Strain Relief Power Cord | |
| 13 | A033748-01 | 1 | Assy., Speaker Mount Panel | |
| 14 | A009574-02 | 1 | Assy., Dual Audio Amp Bd. | |
| 16 | 007882-01 | 2 | Cover, High Voltage | |
| 17 | 006870-01 | al | Brkt., Coin Box | |
| 18 | 000869-01 | 2 | Speaker, Grills | |
| 19 | 002728-01 | 2 | Brkt., Control Panel | |
| 20 | 009992-01 | 1 | On/Off Switch Cover | |
| 21 | 033749-01 | 1 | Bezel with Graphics | |
| 22 | 008903-01 | 1 | Shield, Plex Cover | |
| 23 | 033740-01 | 1 | Panel, Cover with Graphics | |
| 24 | 030868-01 | 4 | Mount, Connector | |
| 25 | TM-127 | 1 | Tech. Manual, with Illustrated Parts Catalog | |
| 26 | 006319-03 | 1 | Copyright Decal | |
| 27 | 033095-01 | 2 | tabel, Shipping | |
| 28 | 005233-01 | 1 | Seal, Rear Door | |
| ant | TM-123 | 1 | TEC Videoelectronics Service Manual |
** The TM-125 weths-Garfiner Service Manual and the TM-124 Motorola Service Manual are to be substituted for Item 29 if a Wells-Gardner or Motorola monitor is used in this game.
- A substitute] for them #10 is A033570-92, 1, PCB Assy., Orbit L (ROM version) © A Warner Communications Company
5-4 ORBIT
A, ATARI’ Figure 5-1 Orbit Final Assembly Parts List
Item Part Number Description
| 34 | 75-99090006 | 6 | Well Nuts, Blind Hole Fastener #10-32 |
| 35 | 82-8016 | 6 | Screws, Button Hd., Socket Cap #10-32 x 1.00 Ig. |
| 36 | 75-5516B | 6 | Carriage Bolts, 4-20 x 1.00 Ig. Black |
| 37 | 75-015S | 10 | Washers, Flat #4 |
| 38 | 75-990505S | 4 | Hex Nuts, #4-20, Nylon Locking |
| 39 | 73-77015 | 8 | Rivets, .187 x .700, Black Anodized |
| 40 | 75-07021 | 6 | #10 Nylon Black Washers |
| 41 | 46-2013002 | 2 | Fuses, 3 AMP |
| 42 | 75-935 | 2 | Nuts, Wing, #4-20 |
| 43 | 75-9158 | 4 | Nuts, Hex, #4%-20 |
| 44 | 75-5524 | 4 | Carriage Bolt, 4-20 x 1.50 tg. |
| 45 | 82-1824 | 10 | Screws, Wood, #8 x ls Lg. Ft. Hd. Phil. |
| 46 | 72-6812S | 12 | Screws, SM. Pan. Hd. Phil. #8 x 3/4" Ig. |
| 47 | 72-6610S | 16 | Screws, SM. Pan. Hd, Phil #6 x 5/8" lg. |
| 48 | 72-6808S | 5 | Screws, SM. Pan. Hd. Phil, #8 x 4" Ig. |
| Ag | 78-25001 | 1 | Screw Down Tie Wrap |
| 50 | 75-0458 | 4 | Washer, Split Lock, k" |
© starrer Communscatons Comoany
ORBIT 5-5
NOTICE 70 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproruzton ioridagn without he Specitic written gerimission of Atari, Inc. Sunnyvale, Galifornia’ This drawing is Only canditionabiy issued anc 1 raceipt nae possession hereo! confers or vanslers any right in, o” Hcense 10 use, ine Subject Matter of tne Grawing or any design or technreal information shown thereon. nae any «ight to reproduce ins Grawing or any oan Ihereot except for manulacture by venéors of Atari incor Dorated and for manutacture under tne corporation's wri fen license, no right to reproduce this drawing is granted 5r'tha subject malter tnereo! uniess by witien agreement et oF written permission Irom tne corporation
Figure 5-2 TV Monitor Assembly A008875-01 D
5-6 ORBIT
Figure 5-2 T.V. Monitor Assembly Parts List
ATARI"
| | Item | | Part Number | Qty. | Description |
| BE | 008897-01 | 1 | Panel, T.V. Shelf |
| 2 | 92-032 | 1 | 23" T.V. Monitor |
| 3 | 75-5120 | 4 | Carriage Bolts #10-24 x 1.25 Lg. |
| 4 | 75-040 | 4 | Lock Washer #10 |
| 5 | 75-911S | 4 | Hex Nuts, #10-24 |
| 6 | 75-010S | 4 | Flat Washers, #10 |
| 7 | 82-405 | 2 | Eye Bolts, 4-20 x 3" Lg. |
| 8 | 75-07002 | 2 | Flat Washer 4, Fender |
| 9 | 75-045 | 2 | Lock Washers, Split 4 |
| 75-9158 | 2 | Hex Nuts, 4-20 | |
| 72-6012 | 2 | Screws, Sm. #10 x 3/4" Lg. | |
| 75-0158 | 4 | Flat Washer, #% |
© A viernes Communications Company
ORBIT 5-7
ANQTICETO ALL PERSONS RECEWING Tris DRAWING e
Figure 5-3. Type B Power Supply A007197-01 D
5-8 ORBIT
ATARI’ Figure 5-3 Type B Power Supply Parts List
| Item | Part Number | Qty. | Description |
| 1 | A009266-01 | 1 | Power Supply Base Weldment Assembly |
| 2 | A006886-01 | 1 | Transformer Termination Assembly “Type B” |
| 3 | 29-053 | 1 | Cap., Sprague Electrolytic 26,000 uf @ 15V |
| 4 | 78-70501SC | ‘t | Brkt., Cap. Mtg. Sprague #4586-48 |
| 5 | A006555-01 | 1 | P.C. Board Rectifier |
| 7 | 79-4411004 | 5 | Fuse Holder, Panel Mounting |
| 8 | 41-2003 | 1 | Filter, Power Line, 5 AMP |
| 9 | A006958-01 | AIR | Volt Selection Block 95V |
| 10 | A006958-02 | AIR | Volt Selection Block 110V |
| 1 | A006958-03 | AIR | Volt Selection Block 205V |
| 12 | A006958-04 | AIR | Volt Selection Block 220V |
| 13 | 78-2708 | 1 | Grommet, Plastic |
| 14 | 72-1810S | 9 | Screw Pan Hd., #8-32 x 5/8” Lg. |
| 16 | 75-048 | 9 | Washer, Split-Lock #8 |
| 17 | 75-918S | 9 | Nut Hex #8 |
| 18 | 75-018S | 8 | Washer Flat #8 |
| 19 | A007192-01 | 1 | Power Switch Termination |
| 20 | 00744401 | 1 | Power In Harness |
| 21 | 46-203801 | 1 | Fuse, 8 AMP, 125V, 3 AG Fast Acting |
| 22 | 46-201251 | 2 | Fuse, 2V2 AMP, 125V, Slow Acting |
L_| QD + Were: Commumeations Company
ORBIT 5-9
@) 2 PLCS Q))
2 PLCS @)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction. forbidden without the
thereon, any ight io reproduce ins crawing ot any par there exept forranuiature ty Yonder of Ata near for manulacture under ihe corporation's wt fen license, na ight to reproduce this drawing is granted Or the subyset matter thereat Uniess by water agreement ‘wih or wetten permission tom the corporatvon
Figure 5-4 Coin Door Assembly
5-10 ORBIT YEL/BK
BK/YEL
A009083-01 F
- 2 PLCS
- 2 PLCS
- 2 PLCS
@)
- 2 PLCS
Figure 5-4 Coin Door Assembly Parts List
ATARI
| Item { | Part Number | Qty. | Description |
| ) 4 | A007637-01 | 1 | Front Bezel Assy.—Used only on -01 Goin Door Assy. |
A007637-02 Ref. | Front Bezel Assy.—Used only on -02 Coin Door Assy. A007637-03 Ref. | Front Bezel Assy.—Used only on -03 Coin Door Assy. A007637-04 Ref. | Front Bezel Assy.—Used only on -04 Coin Door Assy. A007637-05 Ref. | Front Bezel Assy.—Used only on -05 Coin Door Assy. A007637-06 Ref. | Front Bezel Assy.—Used only on -06 Coin Door Assy. A007637-07 Ref. | Front Bezel Assv.—Used only on -07 Coin Door Assy. See Figure 5-5
| 2 | 75-9165 | 4 | Nut, 6-32 |
| 3 | A030362-01 | 1 | Coin Lock-Out Assembly, See Figure 5-6 |
| 4 | A007640-01 | 2 | Coin Switch Assembly, See Figure 5-7 |
| 5 | A002465-01 | 1 | Coin Counter Assembly |
| 6 | 004320-01 | 1 | Coin Door Weldment |
| 7 | 004341-01 | 2 | Secondary Coin Chute |
| 8 | 004344-01 | 1 | Key Loop |
| 9 | 004340-01 | 2 | Spring Return |
| 10 | 004337-01 | 2 | Bracket, Wire Form |
| 11 | 004338-01 | 1 | Lock-Out, Wire Form, R.H. |
| 12 | 004336-01 | 1 | Lock-Out, Wire Form, L.H. |
| 43 | 004326-01 | 2 | Button, Scavenger |
| 14 | 75-046 | 4 | Lock Washer, #6 |
| 15 | 006904-01 | 2 | Spacer |
| 16 | 007359-01 | 1 | Lamp Socket |
| 17 | 70-11-47 | 1 | Lamp |
| 18 | 73-3008 | 2 | Retaining “C” Ring, Truarc #5103-25 |
| 19 | 75-9914001 | 6 | Self-Threading Nut, Tinnerman #SR188006 |
| 20 | 75-026S | 4 | Washer, #6 |
| 21 | 75-00516 | 13 | Kepnut, Style 842, Stl., 6-32 |
| 22 | 008629-01 | 2 | Spring |
| 23 | 71-2118 | 1 | Lock Assembly, Hudson Lock |
| 24 | 71-4225CU | 2 | Coin Mechanism for American Quarter Only |
71-125FB Ref. | Coin Mechanism jor Belgian 5 Francs Only 71-1205FF Ref. | Coin Mechanism for German Mark Only 71-1201MG Ref. | Coin Mechanism for Swedish Krona Only 71-1201KS. Ref. | Coin Mechanism for Japanese 100 Yen Only 71-1210PE Ref. | Coin Mechanism for English 10 Pence Only 71-1220CA Ref. | Coin Mechanism for Australian 20-Cent Piece Only
| 25 | 007753-01 | 1 | Plate, Anti-Probe |
| 26 | A007638-01 | 1 | Switch Assembly, Slam |
| 27 | A006921-01 | 1 | Harness Assembly |
7 |_| _ |
ORBIT 5-11
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbidden without ine Speeitic walter permission of Alar. Ine..” Sunnyvale Caldornia. This srawing is only conditionally issued, and neither receipt nar possession thereat! conters or transiers any right incr license to use, the subject malter of ine ‘rawing of any design ‘or technical informatian shown {erean. nor any right to reproduce thes drawing or any part nereo? except for manuractiure by vendors of atari Incor porated and for manulaciure under the corporation's wht {en incense, no right to reproduce this drawing is granted Crthe subject matter Inereal unless by written agreement with oF wailten permission team Ine corporation
Figure 5-5 Front Bezel Assembly A007637-01 thru -07 D
ATARI" Parts List
Item Part Number Qty. Description
| 1 | 004328-01 | 1 | Bezel | |
| 2 | See below | 2 | Ring | |
| 3 | 004331-01 | 2 | Coin Shield | |
| 4 | 004332-01 | 2 | Primary Coin Chute | |
| 5 | 004327-01 | 2 | Bearing, Scavenger Button | |
| 6 | 004329-01 | 2 | Clamp, Price Plate | |
| 7 | See Below | 1 | Price Plate | |
| 8 | 73-3009 | 2 | Retaining “C” Ring, Truarc #5103-37 | |
| 9 | 72-1604S | 4 | Mach. Scr., 6-32 x | ¥% Lg. Pan Hd., Phil |
| 10 | 75-046 | 2 | Washer, #6, Split-Lock | |
| 11 | 75-9914001 | 6 | Self-Threading Nut, Tinnerman #SR188006 |
FRONT BEZEL | ITEM2 ITEM7 DENOMINATION ASSY VERSION
| 01 | 004330-01 | 004343-01 | 25¢ |
| -02 | 9004330-01 | 004343-06 | 5 FR |
| -03 | 009153-01 | 004343-04 | 1DM |
| 04 | 004330-01 | 004343-03 | 1KR |
| of | 009520-01 | 004343-05 | 100 Y |
| -O6 | 007752-01 | 004343-02 | 10 P |
| 07 | 007752-01 | 004343-07 | 20¢ AUST. |
{ TT
5-12 ORBIT
NOTES:
- Coil data: 10 VDC +2, 50/% resistance, current 200 ma maximum,
- Manufacturer: Coin Mech, Inc. RELAY COIL (PER A007639-01)
DETAIL OF RELAY COIL (A007639-01)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL’ ‘Reproduction “lorbdden. without ne Spocitic written permasion of Alar. ine. Sunnyvale. Galitoria" ths graming vs only conditionally issued. and neiiner receipt nor possession thereo! contars or tranaiors any right in, oF icense fo use. the subject matter oF the Grawing or any design ‘or techaical mlormation shawn thereon, norany ight Yo reproduce Ins drawing or ary pam Iheteot, except for manulacture by vendors of Ala incor porated and for manutacture unger tne corporation's wet ten license. ro ight to "epreduce this drawing 18 granted forthe subject matter thereat unless by written agreement Sith or written permission irom the corporasvon Parts List Figure 5-6 Coin Lockout Assembly A030362-01 A
ITEM | PART NO. DESCRIPTION Qty
Roll-Tight Self-Tapping 004342-01 Switch Mounting Plate 1
65-441C Switch, Omron C-5G3-3 1 Screw MS, #4-40 x %4LG 2 4 72-HA4412
~ | 008824-01 Wireform, Cherry Tr Figure 5-7 Coin Switch Assembly A007640-01 D
ORBIT 5-13
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproauenon foraiggen without the Specific written permission of Atar.. inc. Sunnyvale Calforma’ This crawing 1s only conditionally issued. and
terean, nor any ght to reproduce ? tmereot, excep! for manulacture by ¥ porated and for manutaclure under the ons fen license, no right to reproduce ths drawing is granted or the subject matter Inereo! uniess oy wetter agreement sauth or written permission trom the cerporation
SI mire nt y ia gu 2 2 b ae
@] Wiad
INAS iid
4) Ay oa Or GOs &i
AM Eran x9/m~
/
AM 20M Nein
/
Item Part Number | Qty. | Description
| 1 | A033759-01 | 1 | Assy., | Control | Harness |
| 2 | 033742-01 | 1 | Panel, | Control with Graphics | |
| 3 | 033127-01 | 22 | Busing, | Switch Molded | |
| 4 | 62-009 | 19 | Switch, | Licon | #76-7151 |
| 5 | 62-002 | 3 | Switch, | Licon | #01-700157 |
Figure 5-8 Control Panel Assembly A033747-01 A
5-14 ORBIT
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIGENTIAL” eproduction faroidden without tne Specihc weilten permission of tan Ine. Sunnyvale. Caliioraia” This drawing 1 anly condtionally 1ssved and ‘either vecerpl.nor possession thereat conters or ransiere any right inf license Tg use, the subject matter of ine Sawing or any design or technical intormalion snow thereon. nov any right to fepraguceshis urawing ot any pat! thereat, except tor manulactuce by Vendors oF Atari (aco! porated anc for manufacture urder the corporation's wa fen license, no rignt to "eproduce 1Nis drawing 18 gramed brine subject maiter thereo! unless by writen agreement ‘winy or written permission from the earporation
3 POSITION AMP PLUG AND PINS 1BK 2GN 3W
Parts List
Item Part Number Qty. Description
54-410 1 Power Cord, 12 Foot
| 78-2112P | 1 | Strain Relief | |
| 033211-01 | 1 | Washer, Centering | |
| 79-58110 | 1 | AMP Plug, 3 Pos #1-480700-0 | |
| 79-20123 | 3 | AMP | Pin #350547-1 |
| 78-25002 | 1 | Screw-down Tie Wrap (#10 Screw) |
Figure 5-9 Strain Relief Power Cord Assembly A033016-01 B
ORBIT 5-15
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction. forbdaen without ine Specilic wiltten permission ot Atarn. Ine Sunnyvale. Califorma’ Tris arawing 18 Only conditionally issue, 300 neither receipt aor possession thereo! conters ortransiers Any right in, or icense 10 use, the Subject matter cl the Grawing or any sasign ‘or technical itormanan shawn ‘mereon. nor any rignt fo reproduce Ins crawing O° any Dat! Inereo! except for manutacture by vendors ot Atan Ineo! porated ang lor manvtacture under the corporation's writ ten license, no right ta reproduce Ines crawing 1s granted Dor the subject alter thereat uniess by writen agreement with 0¢ weitten permission trom the corporation
Parts List
Item Part Number | Qty. Description
1 61-062A 1 Toggle Switch, DPST Carling Switch #2GK54 2 006450-01 1 Mounting Plate, On-Off Switch
Figure 5-10 On/Off Switch Assembly A006449-01
5-16 ORBIT
CONTACTS
PLUNGER
. *To lock switch in “on” Position, pull out plunger
Figure 5-12 Interlock Switch Assembly 62-002
CONTACTS NOTIGE TO ALL PERSONS RECEIVING THIS ORAWING 7 CONFIGENTIAL’ “Reproduction lrbiden aiinout the Speurie ites, betmvstion ot ‘tar ine Sunnyvale Caleia Ths eraming v8 ony condiionaly issued, and ‘ener feceipt nor possession thereat cons or ansfers Shy'ngnt nor icense fo use subject matter oF the drawing of anyesign or tectncalilormaton” stow thereon sor any ight fo reproduce nis granngor a" par theveor, except for marutact ure by vendors of Ran, tneor PIN LAYOUT Boraied ona for manutactare vader the corporaten's wnt Ten license. no nght to reproduce Inis drawing vs granted Hise Sabine ate ones auras PUSHBUTTON
Figure 5-13. LED Pushbutton Switch Assembly (Red) 60-002
ORBIT 5-17
BL
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL’ Reproduction lorbiggen without the specific waiter permission ol Atarl, inc. Sunnyvaie. California’ This drawings only canditionally issue. and neither receipt nor possession Inereaf confers or ransters
with or weitlen permission from the co!oration
Parts List
Item Part Number Qty. Description
| 1 | [ | 030835-01 | 1 | P.C. Board |
| 2 | 20-1016 | 28 | Capacitor, Monolithic, .1 hf, 50V | |
| 3 | 41-3003 | 14 | Inductor, 100 wh | |
| 4 | 52-003 | 13 | Jumper, 600 Centers | |
| 5 | 75-E6106081 | 3 | Wingscrew, #6-32 x V2 Lg. | |
| 6 | 75-992501 | 3 | Fastener, %4-Turn, #6-32, Stainless Steel | |
| 7 | 79-517222 | 1 | [ Connector, 44-Pin, P.C. Mount |
Figure 5-14 RF Shield PCB Assembly
5-18 ORBIT
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL. Reproduction forbidden without the Specitic written permission of Atari. Inc.” Sunnyvale Gaifornia. This drawing 1s only conditionally issued. and neithes receipt nor possession ‘nerea! confers or transfers ny right in or license to usa, the subject matter of the Srawing or any design oF Technical information shown nor any right lo reproduce this drawing or any part except lor manutacture by vendors of Alar, Incor fand for manclacture under the corporation's writ fen license. no right 19 reproduce this drawing 1s granted Of the subject maiter thereat ucless By written agreement taitn oF written permiss'on from the corporation.
0062\2-01 voodel\t
BANS BLISOAAD NO Bav Sa0vVvaL DNV VNDIM VWb BD
waa 2 iN)
n a ©
Figure 15 Dual Audio Amplifier PCB Assembly A009574-02
ORBIT 5-19
Figure 15 Dual Audio Amplifier Assembly
© A vvarner communications Combai
5-20 ORBIT Parts List ATARI’
= —_ a -
| Ttem| | Part Number | Qty. | | Deseription | ||||
| [ 1 | 009575-01 | 1 | P.c. Board | ||||
| 2 | 10-5120 | | 2 | Res, Carbon, 5%, ¥W, 1 OM | R3,10 | |||
| 3 | 10-5101 | 2; " | " | " "tog" | R6,9 | |
| 4 | 10-5100 | , 2 | 7 | e | R4,7 | |
| 5 | 11-5221 | 2 | " | " | "ww, 220." | R5,8 |
| 6 | 19-316103 | i 2 | Trimpot, | 10K | RL,2 | ||
| 7 | 24-250106 | 2 1 CAP, Electrolytic, 25V, l0uf | €12,13 | |||
| 8 | 24-250107 | 2 | " | " | " " 100ut | C2,7 |
| 9 | 24-250108 | 2 | # | " | * — 1000uf | £1,6 |
| 10 | 24-250228 | 2 | 2 | ‘ | " 2200uf | c5,Cl0 | |
| ll | 27- 101103 | i 2 ) “ Ceramic, | 100v, .Oluf | c3,8 | ||
| 12 | 27-250104 | 4 | a | " | 25v, .lof | C4,9,11,14 | |
| 13 | 31-Al4F | 2 | Diode Al4F | CR1,2 | |||
| 14 | 31-IN4001 | ! lo | Diode IN4001 | CR3-12 | ||
| 15 | 37-TDA2002zV | 2 | Audio AMP, TDA2002V | 01,2 | |||
| 16 | 69-004 | 1 | Switch, Slide | Swi | |||
| 17 | 78-58005 | 1 | Connector, 10-Position | |||
| 18 | 030184-01 | L | Heatsink | ||||
| 19 | 72-1604C | 4 | Screw, P.H., Phil, 46-32 x % Lg Cres | |||
| 20 | 75-056 | 4 | Washer, Lock, Int Star #6 | ||||
| 21 | 78-16009 | £ | Silpad | ||||
| 22 | 10-5103 | 2 | Pes, Carbon, 5%, W, 10K OHM | R11,R12 | |||
| 23 | 52-003 | 1 | Jumper, .60 Centers |
ORBIT 5-21 Fi igure 5-16 Orbit PCB Assembly A033570-01, -02 A TT TT i Rio S21 91 Tt “WHLN3GIINOO ‘NIAC SIL DNIAIIDIY SNOSHIE TV OL SOON
ATARI Figure 5-16 Orbit PCB Assembly Parts List Version -01
1 033571-01 2 10-5100 3 10-5101 4 10-5102
5 10-5103 6 10-5104 7 10-5151 8 10-5220 9 1o-5221 10 10-5222 Al 10-5331 12 10-5334 13 10-5392 14 10-5471 15 10-5472
10-5682 10-5822 10-5152 10-5223 19-8D9W2PO 10-5683 21-101104
24-250106 24-250227
27-250103 27-250104
27-250224
© A Warnet Communications Company
5-22 ORBIT Part Number | ay. Description
1 F.C. Board 2 Res., Carbon, kW. 5%, 10 Ohm R5,8
| 3 v | " | " "loo " R64,95,96 |
| 40 " | ws | a ik " R1L,4,9,14,18-20, |
23-25,27,28,33,38 40-47,52,57,71,72 75-81,83-87,109,1
| 4 " | " | soe 10K " R11,17,100,105 | |
| 2 " | " | —- 100K " R98,101 | |
| 2 " | S | 150 " R29, 30 | |
| 2 ad | " | _ | 22 " R6,7 |
| 3 " | " | _ 220 % R60,63,108 |
4 " bd La 2.2K " R34,37,53,56
| 3 " | " | “oe 330 " R2,3,26 |
| 2 " | 7 | “oe 330K " R99 ,102 |
| 4 % | " | = 3.9K " R31,35,50,54 |
| 5 " | " | so 470 " R21,22,59,62,65 |
| 18 ” | " | "4 4.7K " = R10,13,15,16,48, |
49,66-70,88-94
2 6.8K R58,61 4 " " vo 8.2K " R32,36,51,55
| 2 " | " | 1.5K " R97,103 |
1 e " wos 22K "R106 1 " Wirewound, 20W, 2 " R1LO4 a " Carbon, kW, 5%, 68k " R10? 4 Cap., Mylar, 100V, .lyf c55-58
Cap., Elec., 25V, 2 " " "
Cap., Cer. Disc, 25V, 46 ” " " " 1Ope 220uf C60 ,61 C33,59
-Olut C43 -l pt Ci-19,22-25, 28-32 34-42 ,44-46, 48-50 53,54,62 2 22ut csl
Figure 5-16 Orbit PCB Assembly Parts List Version -01
Item Part Number Qty Description
33 26-101101 1 | cap., Mica, 100V, l0Opt ca7 34 28-101330 2 7 7 * 33pf 21,27 35 28-101680 2 : " " 68p£ 20,26
38 31-1N100 2 | Diode, 1N100 CR2,3 39 31-1N914 1 " 1Nn914 cRL 41 34-2N3643 2 | Transistor, 2N3643 Ql,2 42 34-2N6044 1 ‘ 2n6044 Q3
45 27-74LS00 4 | Integrated Circuit, 74Ls00 £3,Bé,MB,N1O 46 37-741S02 2 : D 74LS02 E8,NB 47 37-74LS04 4 i " 741804 c4,B9,C?,P10 48 37-74504 1 " " 74804 R3 49 37-741808 5 " " 7ALSO8 M7,C10,D10,C11,D11 50 37-74LS10 1 " " 74LS10 D9 51 37-74Ls11 1 * " 74Lsi1 N3 52 37-741814 1 " " 7ALS14 x11 53 37-74LS20 1 " 7 741820 PS 54 37-74LS30 a 4 . 74LS30 F8 55 37-741S32 4 ° : 741832 P3,B5,C5, £9 56 37-74L842 2 " ” 741842 M5, A6 57 37-7450 2 ” " 7450 F9,19 58 37-74L874 5 a i‘ TALS74 N7,R8,K9,N9,H10 59 37-74874 3 * 7 74874 L7,H9 49 60 37-7476 1 7 * 7476 gO 61 37-741S83 2 " " TALS83 7, HB 62 37-74L886 3 " x 7ALS86 E7, A8,F10 63 37-7490 1 “ bl 7499 Kle 64 37-74109 1 . a 74109 Po 65 37-7415153 6 ” " JALS153 F5,H/J5 ,K5,L5 ,N5, NG 66 37-74154 1 7 " 74154 AS 67 37-74LS157 3 ” " 7418157 BB, CB, J9 68 37-741S161 2 " ” 7418161 ALL, JUL 69 37-74LS163A 2 " " 741S163A K7,J8 70 37-74L8164 2 * » 741S164 A9,ALO 7 37-741S166 1 * s JA4LS166 D8 72 37-7418244 1 7 " 7418244 C2,F3,B4,M4,N4,P4, £12,F12,J12,112 ,M12 73 37-7418273 5 7 " 1418273 C6, F7,£10,E11,F11 14 37-741LS374 z = " 7418374 ES ,J7 75 37-8128 2 ” " 8728 E4,E6 16 37-9312 1 " 9312 R? 7 37-9316 5 " " 9316 R4,R5,R6,P7,P8 78 37-9334 1 " = 9334 M6 79 37-LM323K 1 | Regulator 1M323K 80 37-1324 1 | Avdio amp LM324 B12 al
83 62-001 1 Switch, SPST, Mom (Reset) 66-114PIT 1 " sps?, x4, Dip LiL “|
ORBIT 5-23
A
Part Number
66-118PIT
88 72-1608C 89 75-016 90 75-056C gl 75-916C
93 78-06001 94 78-16005
96 009470-01 97 78-03016
99 79-42C49
101 020670-01
103 90-102
105 90-6001 106 90-6002 107 90-7013 108 90-7022 109 90-7031
111 033688-01 112 033711-01 113 033712-01 114 033713-01
116 033689-01 117 033690-01 118 033691-01 119 033692-01 120 033693-01 121 033694-01
124 033697-01 125 033698-01 126 033699-01 127 033700-01 128 033701-01 129 033702-01
5-24 ORBIT Figure 5-16 Orbit PCB Assembly
NNNN
Pr
AR
B
PERE PE PRPRPR ONNEH
Pepe EP Parts List Version -01
Description
Switch, SPST, x8, Dip M10
Screw, Pan Hd, Ph, 6-32 x 4 Lg, Cres Washer, Flat, #6 Washer, Lock, Int, Star, #6, Cres Nut, Hex, #6-32, Cres
Heatsink (1M323K) Silpaad (1M32 3K)
Heatsink (82S17) k8 ,L8 Cement (82817)
Socket, 40-Pin, Med-Insertion faxy
Test Point
Crystal, 12.096 MHz Yl
| Microprocessor | (6800) | C3 |
MPU Clock Buffer (MPQ6842) D4 RAM (2111) c1,Dl RAM, Pl£ld 1, 0 (82517) K8, 18 RAM (2101A-4)
| PROM, Sync | (828129) | P6 |
PROM, Alphanum (82S115) AT
| ROM, Motion 1 | (8316E) | B/C7 | |
| ROM, Motion 0 | (8316E) | D7 | |
| PROM, Prog 4 | (825137) | N2 | |
| PROM, Prog 4 | ” | Nl | |
| PROM, Prog 3 | " | M2 | |
| PROM, Prog 3 | MSB | ” | ML |
| PROM, Prog 2 | " | L2 | |
| PROM, Prog 2 | 7 | Ll |
PROM, Prog 4 PROM, Prog 4 PROM, Prog 3 PROM, Prog 3 PROM, Prog 2 PROM, Prog 2 F4,H/34,K4,14,F6, H/J6 ,K6, 16
Figure 5-16 Orbit PCB Assembly Parts List ATARI’ Version -02
Item Part Number Description
1 033571-01 1 P.C. Board 2 10-5100 2 Res., Carbon, %W. 5%, 10 Ohm R5,8 3 10-5101 3 " " vo 100 " R64,95,96 4 10-5102 40 " a ik " R1,4,9,14,18-20, 23-25,27,28,33,38 40-47,52,57,71,72 75-81,83-87,109,1 5 10-5103 4 2 ad uo lox " R11,17,100,105 6 10-5104 2 " " oo. 100K " R98,101 7 10-5151 2 " “os 150 " R29 ,30 8 10-5220 2 = " “os 22 = R6,7 9 10-5221 3 x " soe 220 " R60,63,108 lo 16-5222 4 " i} ~ 2.2k " R34,37,53,56 11 10-5331 3 = " soe 330 " R2,3,26 12 10-5334 2 " " a 330K " R99 ,102 13 10-5392 4 " " vo 3.9K " R31,35,50,54 14 10-5471 5 " " “oe 470 " R21,22,59,62,65 15 10-5472 18 = " a 4.7K "“ R1LO,13,15,16,48, 49 ,66-70,88-94
16 10-5682 2 * " ae 6.8k " R58 ,61 17 10-5822 4 " bi uo. 8.2K " R32,36,51,55 18 10-5152 2 ° " a 1.5K " R97,103 19 10-5223 1 " " so 22k" R1LO6 20 19-8D9W2PO 1 " Wirewound, 20W, 2 " R104 21 10-5683 1 " Carbon, kW, 5%, 68k " R1O7 22 21-101104 4 Cap., Mylar, 100V, .luf C55-58
24-250106 Cap., Elec., 25V, l0pf c60,61 24-250227 " " " 220uf C33,59
27-250103 +, Cer. Disc, 25V, .Olyf C43 27-250104 " -l pt CL-19 ,22-25,28-32 34-42 ,44-46 ,48-50 53,54,62 27-250224 -22ut csl
ORBIT 5-25
Figure 5-16 Orbit PCB Assembly Parts List ATARI’ Version -02
Part Number Description
| 33 28-101101 | 1 | Cap., Mica, 100v, 100pf ca7 34 28~101330 2 G 7 " 33pf 21,27 35, 28-101680 2 " " " 68pf €20,26
7 | \ 38 31-1N100 2 | Diode, 1N100 cR2,3 | 39 31-1N914 1 “noid cri
41 34-2N3643 2 | Transistor, 2N3643 gl.2 42 34-2N6044 1 " 2N6044 03
44 | 45 37-74LSOG 4 | Integrated Circuit, 741800 £,B6 ,MB ,N1O 46 | 37-741802 2 " " 74LS02 £8 , NE | 47 37-741804 4 ' " 741S04 04,B9,C9,P10 48 37-74804 1 | : : 74804 RB 49 37-741s08 5 " " 74Lso8 M7,C1O,D10,C11,D11 | 50 37-741810 1 7 . 741s10 D9 51 37-74US11 1 . ” TALSLL NB | 52 37-74LS14 fon f 74Ls14 Kl. 53 37-74Ls20 1 " . 741820 BS 54 37-741830 l " . 741830 F8 55 37-74LS32 4 " ” 74LS32 P3,B5, C519 56 37-74L842 2 " " 741s42 M5, A6 57 37-7450 2 | 7 " 7450 F9,L9 58 37-74LS74 5 " : 74LS74 N7,R8,K9 ,N9,H1O 59 37-74874 3 i " 74874 17 ,H9 M9 60 37-7476 1 7 " 7476 s10 61 37-741883 2 " 7 741883 7, HE 62 37-74LS86 3 7 " 74Ls86 E7,A8,F10 63 37-7490 i oa 7 " 7490 K10 64 37-74109 Joa " " 74109 Po 65 37-741S153 6 ” ” 7ALS153 P5,H/J5,K5,L5,N5,N6 | 66 37-74154 1 " 7 74154 AS 67 37-74LS157 3 " 4 7418157 B8 ,C8,J9 68 37-741S161 2 " " 741Si6L HLL, J1L 69 37-74LS163A, 2 ” " 74LS1LO3A 7,38 70 37-74LS164 2 " ” 74Lsl64 39, A10 n 37-741S166 i 7 7 7418166 D8 72 37-7418244 ql . ” 74Ls244 C2, F3,B4,4,N4,P4, E12, F12,Ji2,L12 M12 73 37-7418273 5 7 " 7418273 C6 ,F7,E10,E11,F1L 74 37-7418374 2 " " 7418374 ES ,J7 5 37-8128 2 2 " 8128 E4, £6 76 37-9312 1 : " 9312 RT 77 37-9316 5 " " 9316 R4,R5,R6,P7, BB 78 37-9324 L ” " 9334 Me 79 37-1M323K 1 | Regulator IM323x 80 37-1324 1 | Audio Amp 1M324 B12
83 62-001 1 | switch, SPST, Mom (xeset) 84 66-114PrT a " spst, x4, Dip Ll
5-26 ORBIT
A, ATARI Figure 5-16 Orbit PCB Assembly Parts List
Version -02
Item Part Number Description
v1
lol
1lo dll 66~-118PIT
72-1608C 75-016 75-056C 75-916C
78-06001 78-16005
009470-01 78-03016
79-42040
020670-01
90-102
90-6001 90-6002 90-7013 90-7022 90-7031
033688-01 033711-01 033712-91 033713-01
033705-01 033706-01 033707-01 RNUNN
»
AR
a
ONNEH
Peee
FI Switch, SPST, x8, Dip M10
Screw, Pan Hd, Ph, 6-32 x 4 Lg, Cres Washer, Flat, #6 Washer, Lock, Int, Star, #6, Cres Nut, Hex, #6-32, Cres
Heatsink (IM323K) Silpad — (1M323K)
Heatsink (82517) Cement (82817)
Socket, 40-Pin, Med-Insertion
Test Point
Crystal, 12,096 MHz
Microprocessor (6800) MPU Clock Buffer (MPQ6842) RAM (2111) RAM, Plfld 1, 0 RAM
PROM, Sync PROM, Alphanum. ROM, Motion 1 ROM, Motion (
ROM, Prog 4 ROM, Prog 3 ROM, Prog 2 (82817) (2101A-4)
(825129) (828115) (8316E) (83162)
(8316E) K8,L8
c3
yl
c3 D4 cl,DL KB, 18 F4,H/J4,K4,14,F6, H/J6 ,K6,L6
P6 AT B/C7 D7
L/M3 K/L3 H3
© #227 Communcarons comoany
ORBIT 5-27
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
APPENDIX A Reference Drawings
List of Reference Drawings
Description Figure No.
Orbit PCB Schematic Diagram ..... Yee Hap = Qe get ye ss Opes ge Type B Power Supply Schematic Diagram ....... 000. c cece ee Coin Door Schematic Diagram. . . .
Dual Audio Amplifier Schematic Diagram .. 0.6... ee eee
Orbit Game Harness Schematic Diagram ......000. 0000 0c e eevee
Orbit Game Harness Layout ..........-..-.-. ee eer
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Bi) Sena AOI
azregels 242egels gv ak 3 g
z 3 § a c 2 & g o
s swe Lp pp | is PeVeVlze ASA J 3
- ry
Ee
NOTICE TO ALL PERSONS RECEWING THIS ORAWING SWE OSSETIA “Repesovenn Ioraaaen without the Yo
seer tees acbne te ose, ne subject matte” ot the EB ¥
sezavian. . ap ated Aeris Srv
eync. PoweR, (rua 3 se ayouy>
Figure 1 Orbit PCB Schematic Diagram Sheet 1 of 6 033570-01, 02
ORBIT A-3
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction foroidden without ine Specie wiilien permsson of Alar, Inc. Sunnyvale. Giiiarnia’ This drawing 1s only conditionally 1ssued. and neither receipt nor possession thereo! conters or translecs ny right invor hcense To use, the subject matter of the Grawing or any design or techmcal information shown thereos sor any right fo reproduce in's grawing or any part Inereot, excep! for manulacture by vendors of Atari Incor porated snd for manulacture under the corporation 5 writ. Fen icense, no night to reproduce this crawing is granted forthe subjec! mater thereo! unless by written agreement Sith or wrlten permission trom fre corporation
a savse—" :
| vel | seuss—“Va | 5 |
's |
| - | asuse—Sla | 3 |
Ln Ao 4 sad
- 23 DECODER
AS
| as | (WARNING | aay |
vecoveny [a)wvece wens DEMUKER — u« 2N3643 aw xu an a8 s W]eanc. orRo@e WA ecrs 2 4
| PANEL BUS 1b —“de. | = | SCRNBFL | cy |
| oll! | s[°So | ANET BUS Bt |
apuss—— Jaz aus? —lar Seat wer
| ang | ne | HEAT | RST LED |
aguse— 4d we = tov
| Tones | -O2 VERSION | +8y |
- (PROs ROMS)
| a6. | (O3ES) | 8 | ||||
| stato ne | phycom | Gay | cea] | sa] | css | peuss |
| al | {Stoo | wim | «sea | wa | zee | > | seuss |
122705 [033700 038707 for used lovee
| j | f | deus | |||||
| 2 | asvsio | —! | lao | ||||
| oe | ah | seuss — #2 | ty | woe | 8] 84 fiz | aves | |
| va | oD eet | Ct) | ' | Abuse | he | e | he |
| R | 1 | #01 | Devs | ||||
| enn | \ | ssus1 | —t | io | a | te | |
| [3 | 2meoee | se0se | —F | lac | oe. | ‘© | _opuse |
| a | puss | 8 | fs | va] | |||
| seuss | —§ | fs | : | aed | = | ||
| = | Anus — I | = | nevss—yesyia | TUT" | |||
| Abus | a. | 2 [630 | |||||
| Aes | a | A | az-vma-aaij-—4 |
>| paps
| 16 | a | te | AB |
| ch (ROWS REF) | 3s | ADs | |
| ° | ba | aba | |
| 3 | 203 | FOR-O1 VERSION |
by 202
| Dr | abt | (PROG PROMS) |
E Re
| wer v | a | ‘8 | dea | CIRCUITRY, SEE |
| = | £ | SHEET 3 | ||
| . | Ee | Teg | Tee | og | |
| f | = | aS | ar | |
| er | [21 | ras —T |
|20-293|90-200] fous ano] cue tows — RouT
MICROPROCESSOR , DECODE, MEMORY
you Ds
{ios p2 fiox cy 04 be
Tf
| - | di | Figure 1 | Orbit PCB Schematic Diagram |
Sheet 2 of 6 033570-01, 02
ORBIT A-5
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
| +sv | sv | sv | av | ||
| ers! | | | neal | |S | = | aaa! | |
‘lab late |
| rez] fede | |r fezJo fede iv l2zl iegie | |r heel | isd | |i | obi wow watls lode | ||
| wr | opces | [cea | Ope | wr | wee | Te | ae] |
| La | Ka | wize | fe | ||||
| 90-7031 | 90-7031 | 90-7031 | 90-7031 | | | |||
| pray | —_2|_@io1a-4) | (201A-4) | eines) |, SG | | | |||
| Pras | —S | fae | i | ||||
| PEAS | I | as | i} | ||||
| eeag | —2 | ae | j | ||||
| PEAS | : | ~ | As | ||||
| pear | —2 | jaa | i | ||||
| prac | 3} | = | my |
peng —4I D7 <
| De | 7 | — |
te! ba 4
eggletens faa 4
| 8885 | )29886 | 123536 | 3 |
| [eado8|e8an8 | |eaan'd | a |
a ji¢ [2 jo i> ia [is Jz Yio 2 fic pps]
| aene | lauce | 2 | » | lange | |||
| agna | gased | aon | 5 | 2 | 2 | -oR2 | 9 |
| Eeeeo | faooea | goood | 2 | & | 8 | geaeoce | Peers |
| Betas | Beseg | Fegee | ie | Fs | £ | gtiate | geege |
ca *
-0) VERSION
| +8V FSV | 4By | av | 7 |
| ABUSIO. | 4, | 1 |
ean rt
| j | le de | 8 | |
| (825137'S) | jeer | cer | ees |
| ne | foo, | on | |
| ABuss— | 5 | Jag | |
| Asuss | © | as | |
| ABvs7 | — | A | |
| ABUSE | . | Ae | |
| ABuss. | 4 | JAS | |
| Abuse | 3 | aa |
asus ——4 a3
| asusz | ——4 | es |
agusi any
| asvse | ns | |, |
RP a Roe apa Ros “Rb ape ry
| ez | = | ee |
soo Gop
| Ve. | oP | TP Fel |
| som | | | | |
Kons 4 Row j tous
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproguction” forbidden witnout ihe Specific writen permission ol Alar! Inc. Sunnyvale, Caiforna. Ths drawing vs oly consiltonally sued. and neither receipl nar passession Iereal comers or transters any right yn_or license fo use. the Subject matter oF the Grawing or any design of technical information shown thereon. nor any right 0 "eDroduee ths Graming or any part Imerear. except for mariutacture by vendors of Atany incor porated and tor manulacture under the corporation's wit fen license. no rmgm lo tepraduce this drawing Is grantes or ine subject mater thereot uniess by written agreement itt oF written Bermissian Hom tne coxporation PLAYFIELD
Figure 1 Orbit PCB Schematic Diagram Sheet 3 of 6 033570-01, 02
ORBIT A-7
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
@7
| eve | : | ey | Sonn | ——! |
3 ‘ eos + bs ish ope af ee ese sree N ve ale : 5 > se >i je nines al u in 7 ir = —Ye
| aps | Ate | 4 | ae | soos | ||
| ala | , | 8 | on} | * | ot | 8567 |
(soe
| epz | Ey | ! |
s| 2 2A co eb 2} 3— 13157
| ul | a | , | 2 |
BA pata Peps
| ee | See BOX 4. liz | u | ||
| “alin | Y | a | i | |
| ore | 2 )Epoe | R | i | Sowa: |
MaTcH o i —_
| vipeD | aT 8 | | | Pra | ||||
| - | _ | — | - | |e | Hl | a | M8] isco |
| r | oun | be | j | H | be | N | |
| 8 | { | | | S65 | | o |
2soue al
| sv | — | wo | 4 | ||
| YY | Tsonae | 3 | iste | | 3] | 57% alo |
| 470 | : | om uz— | Hex’ | ||
| moat | Raas | cau | Ste | viveo | |
| vipRaM | 1 | ‘a | ‘our |
pr (82517) < wap? — Yay POPS Oe nape —lae Try aos las wava—Tae wana —!4]a3 a2 a napo— no omnes —Zqwe cer cezces a J ng
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction lorbidden without the Specilic written permission of Atan. Inc. Sunnyvale Gaistornia Ths drawing is only conaiionally «sued, an either recent nor possession thereof confers or transiers any night in, or heense 0 use, the subject matter ol the rawing or'any design or technical Information shown thereon. aor any right to reproduce nis drawing or any part thereo!, except for manufacture by vendors ol Ata, Incr Doraled and tor manulactute under the corporation's wt fon license. no right to repraduce tvs drawing 's granted forthe subject matter thereat uniess by written agreement taith oe weitten permission trom the corporation VIDEO, VIDEO OUT
Figure 1 Orbit PCB Schematic Diagram Sheet 4 of 6 033570-01, 02
ORBIT A-9
gate oan Ton be fiti i
dause ff i KT Pe
| com? [xij | evs? | se7 [is}-—_——_— | ||
| suam [i] | | | pevse | es | |
| ree 2 sw [ih | + | deuss | ses 6}-———_—_ | |
| ee gs RS | pause | see [ob | ||
| eer at | + | pause | sea [il | |
| Rev 22 | —. | Devsz | saz [7 | |
| TeALera? | — | + a | DBUSi | sa ie |
| 1 | ob 4 | D5Use | <e¢ [s} ——_——— |
Sane dan &\* > Nps
+89 PRBG RBS "ROK ROS
| é | Genre | 20 | ||
| tows | —- | oe | = | 16 pus? |
| ves | — | ol | 3 Skuse | |
| TRIG 1 Sw | + | 5; | Fiz ES Deuss. |
al ses 5 ayer R | pevse Rot a a DBUSS
| aor) | +—— | Deus? |
| tHauste [ih | > | deusi |
Seo Zac Sae7 SRe0 sr
PRAY RM? ORAI SREO ‘
| G8 | Bee wee | 20 |
| Lo} | 2 | ie |
LL peusT aa “7 +> 3 psuse
| mt | 1s) | Ma S _ppuss |
—— 34 vs 2 peusa
| —¢ | ~ | HL | ks DBUSS |
| ' | 8 | 2 pause | |
| +— | — | ' peusi | |
| = 4 | + | He > use |
l 2aae Laas case R47 2 F 2 | ie $5) 4 VELANK —
| fos | | ey | sv |
| i | : | +3 |
ROT 2R69 CRAB 1
| 2 | ] 47K x OPE | 20 |
2 8
| Z | y | pavs7 |
4 ny Pe Boe
| Low sw) | L | 5] | ua | DBuss |
ae $208
| meat Rsv [5 | | = | By os | a Devs |
| SCRNREL | 7} | 4. | pBUSs3 | |
| ewe [el | cs | 2 peus2 | |
| swe /D | an | i _>pusi | |
| GAME RESET ary | } | [2 —pavse |
Neng T8s7 [8 foe <ae Sees scanner —) 8 mee +8
A-10 ORBIT
8 po av 890. SRO! ORO SREB be 2 1
| oY | > | fs |
| = | 12 | B |
| 3] | sae | fF |
=e i o
| im | a | iz |
‘ rm
| me | ri | rn |
6 6 ; r 3 Wie 7
Bo ©
- i 4) PANEL BUS OC
NOTIGE TO ALL PERSONS AECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbiaden without ine specific watien germission of Alar inc Sunnyeale California’ This drawing is only conditionally issued. and nether recewot nor possession thereo! conters ar vansiers any right ino license to use. the supject matter of the Grawing or any design or technical information. shown Mereon. nor any right to reproduce (his Grawing or any Dart thereol, except for manulacture by venaorsof Atari Inco" porated and for manutaciure under the corporation's wit ‘en license. no rignt 19 reproduce this drawing is granted or ine subject maiter thereat uniess by writen agreement lain oF written gerimissian trom the coraoration aust
pause
pauss
peose
pavss
paus2
Deust
DBUSB
Figure 1 Orbit PCB Schematic Diagram Sheet 5 of 6 033570-01, 02
ORBIT A-11
nao
DBs? pevse Deuss, Dasa ppuss Deus2 Deus:
; NAAeS 7 apa e ep pais fa ae
| 1 | is | [ae | Ai | PTS | Se |
| eT ier | 60 | ZT | ssiet | al |
Zig BIN CNTR, 2) ey BIN CHTR, Ga aecc aD c aoe acap ¢ Tena 2 WO ye fs 12 ie F | pai PRs i} Tr
| oak | 4 | . | se | +50 |
ben Tico et aon
By WOISEAMPD — u_ leo cK io
| DBLS7 | ‘Blan | Ba |
| DBUSe | 3)ip | 1Q |
+ ‘6
| _. | . | ppuss—“]7> | 70 |
f — 3
| I | | | { | DBUS4 | > e100 3a) | |
| Velee | | | | | af | ve | |, |
| esos | DBUS3 | 4D | 4Q) |
“wT — FIR
| | | 10 | r | 2 | | | B | 12 |
| i | Beye | ee | |e | vevse—8{ep | sf —-____ | |
| o))e.$—y—]a | on | f |
—_ at \
| e | ae | Davst | 4 Dd | 6a a |
i s
| | | aS | i |
| e Aa ope '
| F stea | Phe | ! | pevse—“|zp | zal |
aes <
| | swiea Oe | | | —s | ||
| it | | | aeser__! | | | |
| asi! | | | RESET | 1 | . |
ani? l c
TP, (Row 10, REF) ond
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproguction”torbiaden. without, the specitic wntten permission of Alar. Ine. Sunnyvale Canora This drawing 14 only conainonally issued and neither rece ct nor possessian thereol confers or transfers any right in. or license to use, tne Subject Matter of the Graming oF any design or techmeal information. snOWN, thereon. nor any ngnito reproduce this draming or any part mereo!, excep! formanufacture hy venaors a! Alan. Ineer porated and for marulacture unger ine corporation 3 wrt ten Incense. no rgntts repradure this drawing ts granted for the subject matter thereo! uniess by atten agreement vith or writien cermiss.on from tne corporation
A-12 ORBIT
in_le
| 7K | . | : | |
| peus7—Blan | ga !2 | or\3 | Re? |
7 [BS ¢——Anore 2 4 ire
| vevse—Shin | ya)? | t |
rs pavss—7> 2a}'&
| paves— | Jan | 4 | : |
Fe ANOTE! pavs2—-3Isp sq!
| pavsi—4fen | eg 8 | —_+ |
pavso—‘lap 2a — Ti a n ye reser — |
nore—!
Ret ANOTE 2
AS +
| soy | wT | <tr, avoid out 2 | |
| nee | Ret | ave | | : |
yy nf] AUDIO OUT 2
| Ie | | | [ | 3K | 180 |
| Bia >t | 5 | KTP AUDIO OUT! | ||
| eek ay | a | 258 | Ros | |
| = | ail | 7 | MT e | X] audio out: |
| waauine #1808) | oR | We | ||
| aoa | cs | Reo | ||
| ican | ne | ] | cl |
a9 ase
| 097 | ese | F88OK | | | | Anote | | vy] |
| isk | AMM | 5 e2! |
= we Cuane Roo +5y yt tow" slo UNREG + [Cel aleve yio To Nowe—J Y] Audio ond
AUDIO, AUDIO OUT
Figure 1 Orbit PCB Schematic Diagram Sheet 6 of 6 033570-01, 02
ORBIT A-13
Spec Giornia’ pense OOM eCn¥
| 2 | oO= | 7 RAG | |
| Sp | oO: | eu | qm |
| cn | cu | de | “ |
| 4 | Ae | pom |
ot \
| ——__, | Lawn] | Lee | -] | Tan Tw trv f |
| | | z |S |e | E/S]o | fJolwls l«l«< | |
| oo | Z|K | xn | Ze | w |
J§| iF
| R jz \é | Hh | / | | |
yf we r
zp b Z G
R = @ D
| iy | g | Be | in | |p | g |
| Ic | » | |< | |b | ||
| ze iS | Pilz | é | c | Ps |
[ be oe ots t] p
| ( | peti | 4s | co | ay | ||
| a | , | a | >» & | |||
| ae! | «1 | fs | Leg - | _ | ||
| = le | lw j= | mw i lye | 1 | |||
| “g | |R | es | jas | | | '€ | |
| 1 | 2 | — | z | iy | Cc | jMR7SO (2Pec5) | ty |
| or | Tell Ties | i | Pa | — | u | |
| | | \inl - Agg | wu |
AIT iqe 1 HIe- 74/98 4 Q Pe xv AK a D < gir | ale
thereon norany sigh ta feproduce!h's drawing Or ay alt heteo! except tor manulacture by vendors ol Atatt incor or the subject matter Inereo! uniess by written agreement santm oF writen Deenission Irom the corporation
Figure 2. Type B Power Supply Schematic
A-14 ORBIT
SLAM SW.°TCH oy oe
GNIR ot BK/OR Oo OR/BK b 15 POS MOLEX
OR 1] PLUG + MALE
BKIY
Y/BK a Sa + oY HW ~OCKOU wit i corn SY} 912
| @N BN 13 | 4 oN | oi “| 8N/B8K Bulek | ois rod | C e Bk/OR Fo } BK/y OC z 13) L 0. L YI BK NO.
c. Vho Nuc. | Naa !
COIN
coin SWITCH COIN *@_~
COUNTER: #2 CLEFT)
(RIGHT) (LEFT)
FRONT VIEW
OF COIN DOOR 68 | TERMINALS
Figure 3 Coin Door Schematic Diagram COIN *\ CRIGHT)
ORBIT A-15
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
A-18 ORBIT le |
& 3 44 POSITION EGE CONNECTOR (2/22) _ BION - 0 “tan Sse Se5 [ie S VET GRD
RIBK
r i
Ey POV_UNREG
RIK HOV UNRES
and
Hy PERSPACE| eu Ts} re RW Bue, [HYPERSPACE LED'S
EAT RESET LED
GAME RESET NO.
L uw Buy S Sw) NO. HEAT SESET NO
slat fle fafa In Wisy, 8B Swe) NO. VIDEO _OoT.
w/eu Ey o> aN Era off]
ewe EOIN LOCKOUT SCEN, REL
Buty We 3 Yor YIBN THeUST 2 NO.
>
le ROTATE 6 2 N.O. CON 2 CEFTIN.O,
Yi.
WIGN oF x]@} fo} |} 3) [au/en ROTATE A 2 NO. WYPERSPACE © NO.
IGN.
5 (sae) Rew. EIZE 2 NO.
1S GY SLAM
oR
wit 192021 COIN 4 (RIGHT) N.O-
=[eIN|Z Yeu ROTATE G& 1 N.O.
BS [| a ew
1520 ai eu/BN
- Sie Wisk, THeUST £ NO. 5V ROTATE ALE NO. O (S81) NO.
rT L wiv
YON 7 S88) NG
WiBD, G (S81) NO.
WIEN why te] fo] 3] 5 (SB2) NO. 4 (S83) NO.
22 23 za Wid | (S84) NO.
a
re 2 (S85) NO. I (S86) _N.O- HYPERSPACE 1 NO.
}3]2}> |e) 3 Fige i NO. Test RUBIO Our Lt AUDIO OuT 2
2 23 24 (5 % 21 2 2 30 SI 2|
28 2% 27 28 29 30 SI Ea Eq AUBIO GRO
- eiex (V] ——___BIGN | 2 3| FoR POWER SUPPLY _ oR SCHEMATIC SEE 4 nm oN ex ys) o07197-01 ri
| a | 7 | idea |
8 w w
| 8} | sowee [s}—t | es | |
| 21 | Swirens | |2 | ie=- Is |
| Bud | 3 | lex | Kp y |
| | | pevour | |#@e— |
Pe he 123 es i #3 L i | re qo T 3|_4 : [64 87 SF] + Le 68 68 of! a lo? 08 6? ol& MONITOR bw
aa L 72 e = oe ore | wrote | it R Se Powis) || fect | (| SP ane Tsu |5|5pv/eu cn WiBK) 3 | pw/Be al | ie
| aala z | i | roan] SPEAKER |
3 Si/3| S|| auore soaro NO ® Wy TREE fle
| —— | Lau ke | 4 5&8 oe | ‘SPEAKER © |
4 SPEAKER 1
en] > al ol fo 9
L 1 _
| ( | L_. | Sof, | |||
| ! | BS | 2 | et | lide: | Pee 5 |
| | | 4g 28 13) | ror | Rorare 8 e | FueusTs, | |
| | | ype | 4| | coin 000R | KORTE |
EIGN SCHEMATIC | 5
| INSOO) | 2) | 030401-01 | cies: | nvPeR- |
| + | a 3 | Hear RESET | SPACRA |
2 “wiser ex |! zee] RiBK |) A S4 S45] FRONT View OF CABINET FRONT SS OF a
Lo NOTIGE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reprocuetion tormduen witha! TNe specific wetten permission of Alan. inc. Sunnwale California. This drawing 1s only cenditinnaly sued. an eutner tecerpt nor possession tnereo! canlers or Iransters Sy right nor heense To use, the subject matter ot Me Srawing oF any design af techmiealormanion shows thereon. aor any ght fo cenroduse tmis Grawing or ay part there! excep! Yor manulacture by vengors of Avge incor Forated and for manufacture under tha corporation s wi fan incense. no right 4a vepraduce tis drawing 's granted brine subject matter tereo! unless by writer agreement wither ariien permssicn fram tne corparaton
Figure 5 Orbit Game Harness Schematic
ORBIT A-19
L DUAL AUDIO AMPLIFIER PCB SPEAKER 2 N
COIN MOLEX CONNECTO! ' i}
! CONTROL H yi MOLEX CONNECTOR | R I
GAME PCB
Figure 5 Orbit Game Harness Layout
A-20 ORBIT
APPENDIX B
Atari Customer Service Information
If reading through this manual does not lead to solving a specific maintenance problem, you can call Tele-Help™ at the following two Atari Customer Service offices.
WEST and CENTRAL U.S.A.
Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time)
From California, Alaska or Hawaii, dial (408) 745-2900
From anywhere else in this area, dial toll-free (800) 538-1611
EAST U.S.A.
Atari Inc. New Jersey Customer Service Office 46 Colonial Drive, Piscataway, NJ 08854 Telex 37-9347 (Monday - Friday, 8:30 - 5:00 pm Eastern time)
From New Jersey dial (201) 981-0490
From anywhere else in this area, dial toll-free (800) 631-5374
Cut along this line
TM-127, 1st Printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A. 'f you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm 0 Distributor O Operator Address ( Other
City State _ Zip
First Fold.
Atari, Inc. P.O. Box 9027 Sunnyvale, California 94086
Attn.: Publications Group, Coin-Op Engineering
Second Fold
e6p3 sly, edey First Class Permit #1004 Sunnyvale, CA
BUSINESS REPLY MAIL No postage stamp necessary if mailed in the U.S.A.
980%6 VO ‘aleaduung 2206 XCg O'd “oul ‘Heyy
Cut along this line
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation Or improper testing.
In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may noi be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
ATARI ING 1265 BORREGAS AVENUE PO, BOX 9027 * ATARI iosriczoco-faexsonce