Juno First
Juno First (Konami, 1983) · Manual · 45 pages · 34 sections · original scan
Instruction Manual
JUNO FIRST (GAME GV-122) INSTRUCTION MANUAL
TABLE OF CONTENTS
SEC. PAGE
1 INSTALLATION. .«...:.00.06065c0as0eeies ean teedees 1
i INITIALIZATION .... 3
Il, = GAME OPERATION...................... 6060s eee ee 3
IV. GAME PLAY AND SCORING ...................... 4
Vv. SOUND... oic:sis siscracnned ausixwanie dnsrendorasinness 6 Vi. GAME ADJUSTMENTS/OPTIONS ... 6
Vil. GENERAL INFORMATION ......................-- 7
Vill. WIRING AND SCHEMATIC DIAGRAMS .......... 9
IX PARTS INFORMATION ..........................+. 23
WELLS GARDNER MONITOR, SERVICE AND OPERATION MANUAL (Attached)
“WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.”
NOTICE WARRANTY INFORMATION IS LOCATED ON THE INSIDE BACK COVER.
FOR SERVICE, CALL TOLL FREE: 1-800-323-9121; (ILLINOIS) 1-800-942-1620
I. INSTALLATION
Ma-400 FILTER BOARD ASSY.
MA-Si3 A3 POWER SUPPLY
GAME ADJUSTMENT ELECTRONICS BOARD SWATCHES [PART OF PWE-1 LOGIC BOARD) MA-376 ILLUMINATION ASSY.
2 ON/OFF SWITCH & PLAYER SWITCHES ih (TYPICAL)
REAR DOOR sf Lock
Ng
Mania? 23189 PANEL JOYSTICK ASSY. ba id
MA-SI9 SERVICE PANEL
FRONT DOOR ¥ “LOCKS
| STEP/TEST | VOLUME | Cort |
| SWITCH | CONTROL | ME: |
CABINET == LEVELERS (2)
| COIN CHUTE | COIN CHUTE | COIN CHUTE | FRONT DOOR | MA-375 | FB | F4 | BRIDGE | FS | F2 |
#2 UGHTS #1 INTERLOCK BOTTOM FANEL = MONITOR 9V. AC RECTIFIERS ISVAC 63V.AC ASSY. FUSE FUSE,
SERVICE COIN SWITCH, ‘OUTLET #1
COIN swiTcH #2 fl PRIMARY POWER FUSE
- INSTALLATION
A. SET—UP
- Carefully inspect the exterior of the game for any damage which might have occurred during shipment. “2 Unlock and open the rear cabinet door.
- Check that ail plug in connectors are seated firmly. The connectors are keyed so they will only go in one way.
- Remove the binding strap from the line cord, and install the line cord plate in the groove provided (see photo).
- Cabinet levelers (2j are stored within the cash box for shipping purposes. Install and adjust as. necessary.
LINE CORD PLATE
B. CHECK-OUT
- Check that all cables are free of moving parts.
- Check for any loose wires.
- Check for loose solder or foreign matter on switches and power supply assemblies.
- Be certain all fuses are seated firmly.
- Be sure transformer wiring corresponds to the supply voltage.
- Refer to section Vi to make all the necessary game adjustments.
- Reassemble the game.
- Plug the line cord into a properly grounded 3-wire receptacle ONLY! c CONTROL PANEL REMOVAL
- Unplug the game.
- Unlock and open the cain chute door.
- Reach in through the coin chute door and remove the wing nut and flat washer from each of the two carriage bolts which secure the control panel to the game. Unlatch the control panel latch at the top center of the panel. Note where the latch strike plate is located. Remove the carriage bolts. 4, Pull the contro! panel back, grasp it at the front edge as far back as it will go (approximately 4").
- Raise the front of the contro! panel approximately one inch above its supports and lift the entire assembly high enough to disconnect plug A9J2/A9P2.
- Remove the entire control panel assembly from the game.
- The joystick’s and leaf-switches are now accessible for removal or cleaning.
- For reassembly, reverse the above Procedure.
MONITOR REMOVAL 1, Unpiug the game.
- Perform the control panel assembly removal procedure (Section C}.
- Unlock and open the rear cabinet door.
- NOTE: The color monitor contains HIGH VOLTAGES delivering LETHAL quantities of energy. Do not attempt to service the monitor until you have shorted the anode plug on the picture tube to ground.
- Disconnect the video plug A17JI, the monitor power supply piug AI2J3/AI2P3 and the ground wire from the monitor chassis.
- From the rear of the game, remove the one nut and one washer from each of the four carriage bolts used to secure the monitor to the platform.
- Remove the monitor from the rear of the game, being careful to clear all cables from the CRT neck.
- For reassembly, reverse the above procedure.
L INSTALLATION, II. INITIALIZATION, Ill. GAME OPERATION
- INSTALLATION
E. SPEAKER ASSEMBLY AND MARQUEE REMOVAL
- Unplug the game. . Unlock and open the back door. 8.
- Unplug the Al5-J1/P1 connector. . Unlatch the two latches on the rear of the Speaker Assembly Panel located inside the back door above the monitor.
- On the front of the game, pull down on the lower molding. under the marquee. The Speaker Assembly will lower to allow removal of the marquee.
- Remove the marquee by lifting it upward out of its track. The Speaker Assembly and Illumination Assembly are now accessible for servicing.
- Tilt the front of the Speaker Assembly downward while lifting the center upward. Pull the assembly straight out to remove. Be careful not to pinch the Speaker Assembly cable.
For reassembly, reverse the above procedure. When replacing the marquee: a. Tilt the front of the Speaker Assembly downward. b. Place the bottom of the marquee in the lower molding track on the front of the assembly. c. Apply slight pressure with your thumbs to the lower left and right corners of the marquee. d. Slowly raise the Speaker Assembly until the top of the marquee is in place in the upper track in the top molding. e. Be certain to reconnect the Al5-J1/P) connector and relatch the rear assembly latches.
Il. INITIALIZATION
TURN GAME ON Immediately, the coin chute lamps and the speaker marquee lamp will turn on.
AFTER A TEN SECOND DELAY A. The attract mode appears on the screen. B. The playing field cycles through the following:
- High Game to Date screen
- Point values
- Game play cycle
il. GAME OPERATION
A. GAME START |. Insert coins into coin chute. a. Coin chute tune is played. b. Total credits are displayed on screen. c.
- Press one or two player button to start game.
a. Total Credits are decreased by one. b. Game initializes. D.
FIRST PLAYER
- The first player's score displays a zero.
- The other player's display will be blank. SECOND PLAYER
- Additional player is indicated by zeroes in the second player's display.
SHIPS/EXTRA SHIPS 1, Each player will begin with three Ships {dependent on Option/Parameter settings).
- Extra Ships are earned by achieving certain score levels (dependent on Option/Parameter settings).
IV. GAME PLAY AND SCORING
CONTROL PANEL The joystick controls the players ships direction of flight. The ship can be moved in one of eight directions. The FIRE button shoots lasers in the forward direction. The WARP button will cause the ship to warp momentarily in order to avoid enemy fire. The one and two player select buttons are also located on the panel.
SCREEN DISPLAYS The top of the screen displays the first players score, number of ships remaining, the current wave of game play and the second players score (2 players). The second line across the top of the screen displays the time (initially 99 seconds) and the remaining number of warps available.
GAME PLAY The game starts with the players ship flying towards the horizon where enemy aliens are seen. The player must avoid their bombs while shooting lasers with the FIRE button. There are two types of enemy bombs throughout the game. The aliens can fire either straight bombs or smart bombs. Smart bombs can be destroyed by the players lasers. If not destroyed,the smart bomb will follow the players ship around the screen. It is advantageous to destroy the aliens as quickly as possible because their longevity allows them to LICENSED BY KONAMI
become faster and more dangerous to the players ship. If the timer is allowed to decrement to zero the player loses his ship.
BONUS PERIOD During each wave, a space capsule containing an enemy astronaut momentarily appears. For bonus points, the player must hit the capsule with laser fire, which dislodges the enemy astronaut, causing him to float freely in space. The player can then capture the enemy astronaut with the ship. At this point the screen will change colors and the enemy aliens stop shooting at the players ship. The Player can now shoot as many of the aliens as Possible for bonus points until the screen changes back to the original color. See ROUND PROGRESSIONS. The player must shoot the space capsule quickly since it appears only for a brief period of time.
BONUS At the end of each wave, another bonus is awarded. The bonus for completing the wave is multiplied by a bonus multiplier to determine the total bonus. The bonus multiplier is determined by the amount of time remaining on the timer when the wave is completed. See BONUS PROGRESSIONS.
IV. GAME PLAY AND SCORING
ROUND PROGRESSIONS (BONUS PERIOD)
*EACH SUCCESSIVE CAPTURE ENEMY FIRST ALIEN ALIEN SHIP
| WAVE | ASTRONAUT | SHIP DESTROYED | DESTROYED |
| 1 | 800 | 400 | |
| 2 | 800 | 600 | Increments by 200 Points |
| 3 | Formation Attack | Per Alien Ship | |
| 4 | 1600 | 1000 | |
| 5 | 1600 | 1200 | |
| 6 | Formation Attack | Increments by 200 Points. | |
| 7 | 3200 | 1600 | Per Alien Ship |
| 8 | 3200 | 1800 | |
| 9 | 800 | 2000 | |
| 10 | 800 | 2200 | Increments by 200 Points |
| iW | Formation Attack | Per Alien Ship | |
| 12 | 1600 | 2600 | |
| 13 | 1600 | 2800 | |
| 14 | Formation Attack | Increments by 200 Points |
3200 Per Alien Ship 3200
*The bonus value for Each Successive Alien Ship Destroyed has a base value equal to 200 points above the first alien destroyed. The maximum successive bonus per alien ship is 3200 points.
BONUS PROGRESSIONS
TIME REMAINING— END OF WAVE BONUS END OF WAVE (SECONDS) MULTIPLIER BONUS WAVE
| 1-5 | 0 | 100 | 1 |
| 6-10 | 1 | 100 | 2 |
| 11-15 | 2 | 200 | 3 |
| 16-20 | 3 | 200 | 4 |
| 21-25 | 4 | 300 | 5 |
| 26-30 | 5 | 300 | 6 |
| 31-35 | 6 | 400 | 7 |
| 36-40 | 7 | 400 | 8 |
| 4145 | 8 | 400 | 9 |
| 46-50 | 9 | 400 | 10 |
| 51-55 | 10 | 400 | iW |
| 56-60 | VW | 400 | 12 |
| 61-65 | 12 | 400 | 13 |
| 66-70 | 13 | 400 | 14 |
| 71-75 | 14 | 400 | 15 |
76-80 15 81-85 16 86-89
The bonus awarded at the end of each wave is equal to the End of Wave Bonus multiplied by the Bonus Multiplier which is determined by the amount of time remaining on the timer when the wave is completed.
V. SOUND, VI. GAME ADJUSTMENTS / OPTIONS
Vv. SOUND
The Sound Board installed in this game has been programmed for Sound only.
VI. GAME ADJUSTMENTS/OPTIONS
| A. | LOGIC BOARD | DIP SWITCH 2 [DSW2} | |||||||
| SWITCH ADJUSTMENTS | sw | 2 | 1 | NUMBER OF SHIPS | |||||
| 7 | OFF. | OFF | |||||||
| DIP SWITCH 1 (DSW1) | OFF | ON | 4 | ||||||
| Coin Chute 1 | ON | OFF | |||||||
| sw | 4 | 3 | 2 | 1 | COIN | CREDIT | ON | ON | 256 |
| sw | 3 | TABLE/UPRIGHT |
OFF Table ON Upright sw NOT USED
| sw | 7 | 6 | 5 | DIFFICULTY LEVEL. |
| * | OFF | OFF | OFF | I {easy} |
| OFF | OFF | ON | 2 |
OFF ON OFF 3
| OFF | ON | ON | 4 |
| ON | OFF | OFF | 5 |
| ON | OFF | ON. | 6 |
| ON | ON | OFF | 7 |
ON, ON ON 8 (difficult)
sw 8 SOUND-ATTRACT MODE OFF No Sound
| * | ON | Sound |
“INDICATES RECOMMENDED SETTINGS
| Coin Chute 2 | B. | SOUND ADJUSTMENTS |
sw 8 6 5 COIN CREDIT The audio output is controlled by the potentiometer mounted on the Service Panel Assembly (located inside the coin mechanism door) as well as the limiting potentiometer {VR200) located on the PWBI Logic Board.
Turning the potentiometers counter-clockwise will decrease the volume. Turning it clockwise will increase the volume.
Cc. MONITOR ADJUSTMENTS
ON, ON INVALID, Normally, few if any adjustments are required for proper monitor operation. However, after any major repairs to the monitor chassis refer to the attached monitor manual.
Fl F2 F3
FS
Fil F2i F31 F32 F4) Vil. GENERAL INFORMATION
A. PRINTED CIRCUIT BOARDS ARE DESIGNATED AS FOLLOWS:
PWBI Logic Board Assy.
A3 Power Supply Assy. A8 Filter Board Assy.
B. WIRE COLORS ARE SHOWN AS NUMBERS:
0 Black
1 Brown 6 Blue
2Red 7 Purple
3 Orange 8 Slate
4 Yellow 9 White
For example, 688 is a BLUE- SLATE-SLATE striped wire.
FUSES
BOTTOM PANEL
Primary Power 4 Amp SLO-BLO 6.3 VAC 3 Amp SLO-BLO
Monitor 2 Amp SLO-BLO
9 VAC 10 Amp SLO-BLO 15 VAC 1 Amp SLO-BLO
POWER SUPPLY ASSY. (A3} +5VDC Source 6% Amp SLO-BLO
| PWBI Logic Board Assy. | +12VDC | 2.5 Amp SLO-BLO |
| PWBI Logic Board Assy. | -5VDC | %& Amp SLO-BLO |
| PWBI Logic Board Assy. | -5VDC | 4 Amp SLO-BLO |
| Coin Meter | +20VDC | 1 Amp SLO-BLO- |
Vil. GENERAL INFORMATION
POWER SUPPLY SPECIFICATIONS
VOLTAGE® PROTECTION
Voltage adjustable. 6 Amps over-voltage protection and fused for over-current protection. 1.5°Amps fused for over-current protection. The reference for this circuit is a 1N4742A +12VDC Zener controlling the base of an emitter follower pass transistor.
20 milliamps fused for over-current protection. The minus 5 volt supply is the 7905 IC regulator. Full wave rectified unfiltered voltage, fused for over-current Protection. Full wave rectified unfiltered voltage, fused for over-current protection. LOCATION
Logic Board Assy. +5VDC
Logic Board Assy. +12VDC
Logic Board Assy. -5VDC
Coin Meter +20VDC
Coin Chute Lights +4,5VDC
Monitor and Marquee 1OOVAC or N5VAC, GOHZ Isolated, fused AC voltage.
VII. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
TABLE OF CONTENTS
PAGE
LOGIC BOARD ASSY. COMPONENT LOCATION AND SCHEMATIC DIAGRAM [SHEET 1 OF 2).............6. 00 cece cece eens 1 COMPONENT LOCATION AND SCHEMATIC DIAGRAM (SHEET 2 OF 2).............6. 00 cee cence eens 14
POWER SUPPLY ASSY. {A3) COMPONENT LOCATION AND PARTS LIST .. seeee 17 SCHEMATIC DIAGRAM .......... 0.0 secre cree eee e ene n eee e ne en eee 18
PRIMARY POWER/FILTER BOARD ASSY./ INTERCONNECTION DIAGRAM.......... 20.6.0. 6 ccc cece center e enn 20
VII. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
The following parts list contains unique parts used on the
PWB-1 Logic Board Assy. All other components on the PWB-1
Logic Board Assy. are standard parts.
DESIGNATION PART NO.
74LS8293 XO-717 74L8375 X0-718 74L8257 x0-719 7489 XO-~88 74153 XO-721 Konami 1 CPU XO-741 M14081 ° XO-725 M14082 XO-740 M14083 X0O-726 K-8207 XO~-727 74LS14 X0O-728 74LS21 X0-729 Z80 CPU X0-730 MS5L8039-8 CPU XO-731 AY-3-8910 X0O-733 LA4460 X0-732 MSM4066 X0-734 74L885 XO-735 74LS393 XO-736
2SA697 XO-722 28C2320 XO-723
181588 XO-724
VII. WIRING AND SCHEMATIC DIAGRA ow
LOGIC BOARD ASSY., CON .
220UF 4.7UF 35V @ VON 30° = 220U 10' ¢
I <r ' i o 0 isist4 19st i} +81 0 [os74 228190) ssi [sersiq | oe 4 ) 1 1 ' t '
> (49) Os
1: i zees4 00874 ( visi} aves | ve7sl 0 bvest o ) 192814 2g2s7 [zos § eos 4) ves vis e2is14 eszs74)) sels7 YOLOANNOD dOb
o 470|
WOLSNd
.7KX 4 R-AR lorsT¢ &
sais7d
- zesid()[ ezesrd [ein
YOLOANNOD dO” x
best x 0 bbest > 0 [98514 28874 0) [szis74 [ezs14)
NOTES © CERAMIC CAPACITOR <= 0.1UF CERAMIC CAPACITOR © ELECTROLYTIC CAPACITOR © 1c SOCKET @ TANTALUM CAPACITOR @ MYLAR CAPACITOR VII. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
LOGIC BOARD ASSY., COMPONENT LOCATION
| A | B | E | F | H | J | k | L | M |
| soooyr 1000UF | 14.318-“BAND | 820 | ||||||
| 25 | 2v©® | vr200 0 MHZ | => | = | => |
OUE ©) 2.2K S0V@OW 7404 4066 L393 agsue 419 :
| WIS | | « | LID | Ni | 109PO*470P© |
| NS | 3 | 0.22UF |
uN > 101K
| Boat | | BAK 5 ON 35v@ | pas | i | 10K .,200K 100K |
8910 LS393 rasa Ls3e7 a > 0 1
220 X19
2862320 { st \2732 | © 1 2114 2.2K R-ARRY'S — =
our om 470p| ) 8S Ls273 LSO8
il Lsos LS273 LS273 LS244 1s273 Lsi53 LSI53
LS273 LS153 LS153_ = LS153 you
NOTES © IC SOCKET © CERAMIC CAPACITOR @ TANTALUM CAPACITOR @ MYLAR CAPACITOR =} 0.1UF CERAMIC CAPACITOR © ELECTROLYTIC CAPACITOR
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
VII. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
=, yn co} 10Vv
> SOLOSNNOD dob
x bp2sl o 0 2sgzs7 2g2¢s7 ()|z0s1 80s7 [ees »s14 seis} sszs14() geist
YOLOANNOO dOb
w 0 | e287
© |C SOCKET @ TANTALUM CAPACITOR @ MYLAR CAPACITOR 4.7UF 35V © sO —> © ' v9lZ ! © 19)
> { [0814 sesi9 () azisq ws74) o 191874 iaistg()[ e254 0 vost} zzs74()| 1287
© CERAMIC CAPACITOR 4.7K X 4 R-ARRYbs [eses} \ blest 0.228 [ vast} ( 875) [ z9e87 zes14) ves7 4 9181
an
<=> 0.1UF CERAMIC CAPACITOR © ELECTROLYTIC CAPACITOR ow oo as 3 2 => —7 => 220UF, 10v©) a 5 ST! !
| Te | Ilee | ll es | |
| oy le | Qn | Bn |
331123 (log [led | @F Hoe [1/O* | O° |
| 1 | [ | meena By | =I |
eee peer i
| r | => | SI | } | ! | |
| 5 | c | 1 | ie | 1 | | |
on o =
| H H | 8 | of | é3 Th |
ao
| 3 | 8 | 1% |] 8 1 |
| | | | | 4 |
Lab] 33 1K X 8 R-ARRY , 1KX8 R-ARRY'S
| na | te] | fe | ||
| 7) | c{| | HW ¢€ fi | ||
| #] | 1el | rah | fs | l |
| N | BK!) Oo |r | ~ | 33 |
a if = =>
| i | 1 | r | ||
| cr | =a i | | | on | r |
| g | EIniosiq | & | Fy | ||
| ud | 2 lf @8 Hh 7 | a = |
1k; I toss
s0s7 vls1
e3 ). fe} l 33)
LOGIC BOARD ASSY., COMPONENT LOCATION
47U SV oro — orsoo oo OO m
© mass ==5
FA
ia a—1001 [ss5] CED fo) 25C2320 ‘o.1uk— \_/1our, 16v ©) 14 15 16 1K X4 R-ARRY'S | c => vomit '
o |! ao 1] & ws], [a i ja ! =u
oc 18.432 MHZ
BAND a PO) 22K4__2SA697) i) oO (158m 1K E a 220uU OV 1s04 VII. WIRING AND SCHEMATIC DIAGRA
a TG HALTACK 1508 Hho! 843erH2
| 1816 1x2 | LW | 7 |
A couwreek Far av-—4} 4B1s—4
| ae ls | a | ie oy eet | ||
| 4 | a4 | 10o7—4 | a pat | 2 |
| of | a5 8) 9. YRS | h—118 gi Toe | ||
| Hata “87a £13 |. | 40-—9) | —i5 | 2 | |
| 2 | eels 1 aes | ai |
24 40%
| 1se6x7 ans) | RCS | * | if |
| ait — Soir_[s” | p | Aa |
rary uf aes aa ye Lee, | 4874 818 3 35
- HALTACK: §
| -ALATCH | Lo | 2 |
® ©8600 157442
NOTES
CERAMIC CAPACITOR TANTALUM CAPACITOR
ELECTROLYTIC CAPACITOR MYLAR CAPACITOR
RESISTOR PACK Pie it
| le | (3742 | as | p | bn |
: . i
| raphe | Has ap | “ate |
| m ri qe | HI2 | i |
9 Bat Lee phe? aaa
apoaF T = 8c 1586x14 4—Elico 1 MeF—4 VEL. 470PF XB 2a taal
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
777.
COM 1 “et 744
-o1
i 7 3
| TE | 3 | <le | 6 |
LINE FILTER
SERVICE 00 700 OUTLET a
kau Tit
Ai2 4
| P33 | | | Tar | ||
| > 1 | St | 7 | lbh | + |
| MoNiTOR | H | tm | tl | a |
>2 A< 9 <+ —
H H i '
- ' = at2 i
| Pa | us | H | |
| -{“ BaLLast | ——1822| | azz] | _| |
| ! | Ci | a | fen |
ee ee ef FLUORESCENT | LAMP 533 | STARTER
| NATION ASSY. MA-376_| | = | rn |
- CIRCUIT EARTH ee GROUND GROUND
TO FRONT DOOR =
ah TO SERVICE PANEL <«——
To CONTROL PANEL
TO REAR DOOR coor)
VII. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
ALL RIGHTS RESERVED
D.GOTTLIEB & CO
REFERENCE
cH, C42. a2 13, C23 C14, C43 c2i cal Du, D25
Di2
D2I-D24 D26
D32, D34 D41, 42, 044 Ful F2I 31, F32 Faq PI t+
Diz Lib}
ae Fev scenf—_] {=} as ; ria ci 4p + 4
13 4k POWER SUPPLY ASSY. (A3}, COMPONENT LOCATION
042 hq
p41 i
p34
- '
| D32 | bay | i | hn |
| oO | oO | + | |
| cc | {2 | 2 | z |
R16 = 024 ST
Ria ol. Cove u 023 —C I} oz 4} ,
n
POWER SUPPLY ASSY. (A3), PARTS LIST
DESCRIPTION
Power Supply Assy
Capacitor, O! mid, SOV Capacitor, IOOUF, 16V Capacitor, 0.1UF, 100V Capacitor, 0.2UF, 16V Capacitor, 2200UF, 75V Capacitor, 470UF, 35V.
Diode, Light Emitting MV-5752 Diode, Zener, 5.6V, 5%, IW, IN4734A, Diode, 15401 Diode, Zener, 121, 1N4742A 5%,1W
Diode, 1N4004 Fuse, 6/4 AMP SLO-BLO Fuse, 24 AMP SLO-BLO Fuse, % AMP SLO-BLO Fuse, 1 AMP SLO-BLO Comector, 4 PIN PART NO. REFERENCE
MA-513 P2 XO-229 P3 XO-235 Pa XO-234 fell XO-205 ar XO-132 a2 xO-284 Ril RI2 xO-270 RIB, RIS XO-255 RIS RI6 XO-263 RI7 X0-257 Rig R22 R23 xO-254 Ral ELS scrit EL-21 ull €L-S U4) EL-6 VR PS-87 DESCRIPTION PART NO. Connector, 10 PIN XO-531 Connector, 7 PIN XxO-526 Connector, 16 PIN XO-372 Transistor, PNP, 2N5879 XO-323 Transistor, NPN, TIP3IB XO-641 Transistor, NPN, 2N3055 xO-301 Resistor, 470 OHM, 5% /2W XO-55 Resistor, 100 OHM, 5% IW XO-137 Resistor, 12 OHM, 5% 2W/ XO-138 Resistor, 200 OHM, 5% ¥\W/ XO-143, Resistor, 180 OHM, 5% “AW XO-24 Resistor, 100 OHM, 5% YAW xO-28 Resistor, 20 OHM, 5% YW xO-29 Resistor, L8KOHM, 5% 2W XO-135 Resistor, 820 OHM, 5%, 2W X0-706 Resistor, 750 OHM, 5% iW XO-136 Silicon Controlled Rectifier XO-131 Diode, Programmable Zener TL431_ XO-272 Voltage Regulator +5V,LM 320 XO- 572 Potentiometer, 100 OHM xO-134
Vil. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
HS, TO-3 -2ut ['
+48V 0C Tees ean
| ot our | 8K | 323 | 2N3055 | 23 |
| 75V | R25 | lat | ||
| ‘ | + | 2w | 50V | |
| ! | 025 | yw | D26 |
i iN4-742A
| H | MV5752 | 12V, 5% |
| \ | iW | aa |
' 1A SB. D32 : 1N4004 ' fNa004 s< '45V_AC CENTER TAP N 034 y i — p42 IN4004 lisv AC \NPUT - inaoo4 | F352
' Be. ' \ D44 IN4004 ' ' ' U44
| 6 | | AUDIO GND | poe Dc | IN} | LM320 | ||
| 4 | 750n | 470uf | .Oluf | MLP-5,0 | .2uf | |
| ' | = | Ww | 35V | 50V | (7905) | 16V |
| H | R41 | *) cal | c42 | 143 |
‘ =
| 1 | 043 | 40 | L | = | . |
| H | Mv5752 | - |
P4 oc RC __+5v OC ( SOURCE) 316 IN4734A t 15 Di2 H 5.6V, 5% :—— > 13 Ww 1 Ru 22 470n ' .5W er cl4 20n H MV5752 > 10
POWER SUPPLY ASSY. (A3), SCHEMATIC DIAGRAM
VII. WIRING AND SCHEMATIC DIAGRAMS, PARTS LISTS
| Fa | 5 Ate | ve | AB gg 7 | ||||||
| , | Fa [err | ws Al 5 [205] | 200] 1," & | Pa, ot [585] +5v 0c | |||||
| I | 10a | H i | 1? 877 | ||||||
| ‘SLO~BLO, | ! i | +> g5el_+sv pe | |||||||
| A | i | 209 | mal! ad | iol | |||||
| wen Pe | ' | H i | |||||||
| Tr ge, tt | io | | : | ! | | ||||||
| t H | ' Ii | ! H | i 1 | ||||||
| | | : ii | ad | 1<3 <- | |_ [3] 6no | |||||
| 744] | 1 fra] | ' 1 | ack | 18> | |||||
| 5 | : | | | ey 75} Fe 1 no | ||||||
| ' : | aA | all | > 7>4 | TO ABU7-4 | |||||
| H | SLO-BLO | ti | as | | t i | To ABU7-1 | ||||
| io | 1 | 15V AC | dit} Jo | at J2 P2 | i L EI GN | ||||
| ' H | ! | 2 | >6 | ||||||
| ! ‘ | i fiigier | peasy | i GS | ||||||
| ane, | us, | ' ‘ | 1 JIE _ [738] sv ac center Tap (RETURN) | 133 | RB] | 35> 3 a | |||
| INTERLOCK INTERLOCK i i | fo dierty | i | ! i | ee | |||||
| c 72 | t ' | t (G42: [azz] t5v ac &. | 155 | 155) | 5] iy et | ts 2>t1 2 | 6nd | 2S | ||
| ' ! | 2] | 1A | rt << | key! 14 | | P2 v2 | ||||
| ' i | ' 31 | sLo-BLO | H i | 3 2 | S950 “o> LEFT | ||||
| COM 2 | : 4s [raz | 766 ' | 1 ‘ POWER SUPPLY ASSY. 7 H | ||||||
| 700) | 722 3< | fell | ‘ | ||||||
| Ss | <3< | i i oa] 36v Ac | aa | A] | oe! | MA-513 | eae | | | fa |
| H : | ' | ; | a | ||||||
| 1 | ALINE | 1 | A, RIGHT. | ||||||
| =i | ~~ | i | “ | Ti | _ | _ | | | ||
| H : | H | H | 775 DOWN | ||||||
| — | ' j | [055 | H | T | |||||
| INPUT_ POWER | Tat | em | Tal eg Tas | Tes] { sev |! | gest | | | |||
| 1i5V AC | H H | + 3iI | H | wolle PLAYER 1 | |||||
| Solty COHZ | 1 ! | 1 3}, [O55] 35V-AC (RETURN) | (055 | oss] | [reo | ||||
| i H | ell | ' | mle PLAYER 2 | ||||||
| nore: | P| | il | ae | ||||||
| INTERLOCK SWITCHES SHOWN | d H | coMMON | i | sf WARP BUT | |||||
| IN DOOR(S) OPEN POSITION, | H ‘ | | 211] F2 [oes | H | | o———_ | |||||
| i H | I BV AC SA” | H | |||||||
| H ' | i | SLO-BLO, | i | en | ae | ||||
| ' ' | Ey | - | 9 5 | q 2 | 91} | i —o | o——_— | |||
| i ' | i | oF | CONTROL PANEL | ||||||
| i j | SERVICE | il a6 | = | 2 | |||||
| Hl Hi | OUTLET | H | |||||||
| Too] ty <} [700 | ' ; 3y AC | P/O | |||||||
| H j | i | {(RETURN) | R BOA | ||||||
| ! i | =) | i dl | ¥4.5V 06 | I FILTER G0aRD | H | ||||
| 1 H | i | ot | ' | { | |||||
| ' H | i |i | \ers var) | H | ||||||
| M1 teo et [ | 1 fl soo] svac_ FS. | crow. sTRAP | i | ||||||
| H | i | | | Lit | ||||||
| ' | | foov ac | sae | \ |
i ‘ tl
| ‘ H | ii Sit] common | B | LL _FRONT_DOOR |
: i t i 1 t ' (477 3 a2 H H
| 8s PM et ie | . | \ | |||
| MONITOR | Ly i wz] 14 .| BZ | ( | ) | +20v DC | 433) |
| meet | yo | any ae |
'
| ! ! | } FS owuF | =a | 1] gl A 1 1088 | ||
| ' H | BOTTOM PANEL ASSY. | \ | key | ) | ; Lialadihd Lce<i lat? |
| --e- ee | i ! | MA-375 | Pio Y | Ue _4 rag | |
| J | TEL! get | soz 4 | 2 | ||
| | | BALLAST ! | i<10<+ | 10 | Speaker | |
| : ' | ae | 0.30 |
- H ' 1! ' +12v 0c
| | | : | mig | fl |
| ~5V DC
| | 833 | | | AUDIO GND |
a STARTER wh ILLUMINATION ASSY. MA-376 =< CIRCUIT EARTH GROUND GROUND
TO FRONT DOOR =
TO SERVICE PANEL TT)”
TO CONTROL PANEL TO REAR DOOR LOCK es a
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
IX. PARTS INFORMATION
TABLE OF CONTENTS
PAGE
SPEAKER/MARQUEE ASSY. .............. 24
ILLUMINATION ASSY. .................-.5 24
IX. PARTS INFORMATION
SPEAKER/MARQUEE ASSY. AND ILLUMINATION ASSY.
| \ or som | Y \OX 6 7 8 9 i] 10
ITEM _— DESCRIPTION PART NO.
| 1 | tumination Assy. | MA-376 |
2. Starter EL69
| 3. | Ballast (60 HZ) | EL-70 |
| 4. | Lamp, Fluorescent | lA4 |
| 5. | Cable Assy. | MA-364 |
| 6. | Speaker Assy. | MA459 |
| 7. | Cable Assy. | MA-3I8 |
| 8. | Speaker | EL-93 |
| 9. | Speaker Grill | B-20931 |
| 10. | Marquee, Lexan (Screen | A-23195, |
| nH. | Speaker Guard | B-20931 |
IX. PARTS INFORMATION
CONTROL PANEL ASSY.
ITEM —_ DESCRIPTION PART NO.
1. Control Panel Assy. MA-I137
| 2 | Joystick | 23189 |
| 3. | Short Button (6) | A-21970 |
| 4. | Button Holder and Switch (6) | A-21971 |
| 5. | Cable Assy. | MA-SI4 |
| 6. | Lexan Overlay | A23196 |
IX. PARTS INFORMATION
SERVICE PANEL ASSY.
yPWnNa q DESCRIPTION
Service Panel Assy. Cable Assy. ‘Switch {Push Button] Volume Control Coin Meter PART NO.
MA-5I9 MA-518 EL-57 X0499 EL-84
IX. PARTS INFORMATION
BOTTOM PANEL ASSY.
ITEM DESCRIPTION
- Bottom Panel Assy.
- Transformer
- Capacitor, 50,000UF, 25V
- Resistor, 200 OHM, 5%, 20
- Fuse Holder Fuse, 3 Amp, SLO-BLO
- Cable Assy. (Secondary)
- Fuse Holder Fuse, 1 Amp, SLO-BLO
- Fuse Holder Fuse, 10 Amp
- Bridge Rectifier (2) to. Fuse Holder Fuse, 2 Amp, SLO-BLO Mn. Fuse Holder Fuse, 4 Amp, SLO-BLO
- Service Outlet B Line Filter 14 Cable Assy. (Primary) PART NO.
MA-375 C2209 XO-141 XO-142 ELO EL-9 MA-SI7 ELO EL-6 EL-O EL-23 EL42 EL-78 EL-7 EL-78 EL-33 A-18133 EL-50 MA-363
IX. PARTS INFORMATION CABINET PARTS
2,3
| ITEM | DESCRIPTION | PART NO. | ITEM | DESCRIPTION | PART NO. |
| 1 | Vent Channel (2) | D-21754 | 10. | Shield, Top | D-22632 |
| Z. | On-Off Switch | EL-56 | 1h | Shield, Bottom | C-22633 |
| 3. | Switch Plate | A-223% | 12, | Monitor Cable | A-23244-1 |
| 4. | Cable Assy. Master Electronics =MA-515 | 13. | Clip Bracket, Shietd | B-22631 | |
| 5. | Interconnect Cable | MA-SI6 | 4. | Cover Plate, Line Cord | A-21955 |
| 6 | Back Door | D-23073-3 | 15, | Line Cord | B-15357 |
| 7. | Master Electronic Board | MA-II57 | 16, | Cable Assy. High Voltage | MA-360 |
| 8. | Rear Door Lock | MH-O | 17. | Interlock Switch | EL-66 |
| 9. | Anchor Plate, Lock | MH-1 | 18. | Cover, Interlock Switch | A-21888 |
IX. PARTS INFORMATION CABINET PARTS
11 ; ~~ 7
| TEM | DESCRIPTION | PART NO. | ITEM | DESCRIPTION | PART NO. |
| 1 | Rear Side CRT Decal | A-23198 | 7. | Cable Assy. Front Door | MA-396 |
| 2. | Top Glass | A-22464 | 8. | Interlock Switch | EL-66 |
| 3. | CRT Frame | A-23199 | % | Cover, Interlock Switch | A-21888 |
| 4. | Monitor Filter Glass | C-22849-1 | 10. | 3” Leg Adjuster (2) | MH-21 |
| 5. | Monitor Mask | D-22463 | ia | Lexan Overlay (Screen) | A-23197 |
| 6. | Monitor | C-23260 |
SERVICE NOTES
wells-Gardner elecTRONICs We ORPORATION
19” IN LINE COLOR MONITORS
MODELS
19K4901 19K 4906
19K4951 19K4956 19K49SIRYC
wells-qardner electronics
CORPORATION 2701 NORTH KILDARE AVENUE CHICAGO, ILLINOIS 60639
WARNINGS
- Power Up Warning— An isolation transformer must be used between the AC supply and the AC plug of the monitor before servicing or testing is performed since the chassis and the heat sink are directly connected to one side of the AC iine which could present a shock hazard. Before servicing is performed, read all the precautions labelled on the CRT and chassis.
- [X-RAY RADIATION WARNING NOTICE |
- High Voltage— This monitor contains HIGH VOLTAGES derived from power supplies capable of delivering LETHAL quantities of energy. Do not attempt to service until ail precautions necessary for working on HIGH VOLTAGE equipment have been observed.
- CRT Handling— Care must be taken not to bump or scratch the picture tube as this may cause the picture tube to implode resulting in personal injury. Shatter proof goggles must be worn when handling the CRT. High voltage must be completely discharged before handling. Do not handle the CRT by the neck.
- | PRODUCT SAFETY NOTICE
AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L’APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.
For replacement purposes, use the same type or specified type of wire and cable, assuring the positioning of the wires is followed (especially for H.V. and power supply circuits). Use of alternative wiring or positioning could result in damage to the monitor or in a shock or fire hazard.
PERFORMANCE AND OPERATING DATA
- Apply a suitable power source to the monitor through an isolation transformer.
- Apply a suitable signa! source to the monitor PCB by means of P201 and P202
- Set Up Controls. All controls are preset at the factory, but may be adjusted to suit program material. 1.0 Supply
Voltage 108 VAC-132 VAC
Frequency 50 Hz-60 Hz
3.0 Service Set-Up Controls MAIN PC BOARD 3.1 Vertical Hold Control, VR301 3.8 Horizontal Width Coil, L352 3.9 Black Level Control, VR201
3.2 3.3 3.4
3.5
3.6 3.7 Vertical Size Control, VR303 Horizontal Hold Control, VR351 Vertical Raster Position Adjustment Jumper (3 positions) Horizontal Raster Position Adjustment Jumper (3 positions) Screen Control (Part of H.V. Unit, T352) Focus Control (Part of H.V. Unit, T352) 3.10 Horizontal Video Position Control, (Horizontal Shift) VR352
NECK PC BOARD 3.11 Video Drive Controls, Red VR401 Green VR402 3.12 CRT Cut Off Controls, Red VR403 Green VR404 Blue VR405
SERVICE INSTRUCTIONS
1.0 BLACK LEVEL CONTROL ADJUSTMENT 9.0 HORIZONTAL WIDTH ADJUSTMENT This control has been set at the factory and should not The horizontal width coil is a hexagonal tuning tool adneed further attention, however, when the game is con- justment. This contro! must be adjusted slowly. if nected a slight adjustment of VR201 may be necessary to necessary. until the picture or test pattern attains the corobtain the proper black level (the black portion of the pic- rect horizontal proportions. ture just extinguished).
2.0 VERTICAL SIZE (HEIGHT) Location of this contro! is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions. 3.0 CIRCUIT PROTECTION A 4.0A pigtail fuse, mounted on the Main Board has been GRN __ig*__ Ri provided to protect the Power Output Circuit. DRIVE ORIVE RED CUTOFF 4.0 FOCUS GRN CUTOFF’ Adjust the Focus control, located on the HV unit(T352), BLU CUTOFF for maximum over-all definition and fine picture detail. NEG H SYNC 5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, neo v syne VR351 (See Fig. 1) GND A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor Pos H SYNC
HORIZ. being driven from the game signal, short TP601 to TP31. POS V SYNC, 2 WIOTH Adjust VR351 until the picture stops sliding horizontally. GND COIL Remove the short. BLU
6.0 HORIZONTAL VIDEO POSITION GRN If the video is off center on the raster some compensation can be made by adjusting this control.
7.0 VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions “U” or “D”.
8.0 HORIZONTAL RASTER POSITION ADJUSTMENT
If the video is off center horizontally (long dimension of HORIZ HOLD
BLK LEVEL
the picture tube) some compensation can be made by HORIZ VERT VERT VERT HORIZ moving the horizontal raster position adjustment Jumper Centerine SIZE HOLD Rasrer weer to either positions “R” or "L”. FIGURE 1
INSTALLATION AND SERVICE INSTRUCTIONS
1.0 DEGAUSSING The monitor is equipped with an automatic degaussing circuit. However, if the CRT shadow mask has become excessively magnetized, it may be necessary to degauss it with a manual coil. Do not switch the coil OFF while the raster shows any effect from the coil.
2.0 COLOR PURITY AND VERTICAL CENTERING ADJUSTMENT 2.1 For best results. it is recommended that the purity adjustment be made in the final monitor location. If the monitor will be moved, perform this adjustment with it facing west or east. The monitor must have been operating 15 minutes prior to this procedure. 2.2 Set the converger assembly on the CRT neck with the center line (of the Purity Adjustment Magnet) over the gap between grids no. 3 & 4, (See Figures 2 & 6) 2.3. Make certain that the magnetic ring-pairs are in their correct positions before starting procedure, This produces a zero-correction state and helps facilitate adjustments. 2.4 Vertical raster position adjustment jumper must be in position “C” (center). 2.5 Remove the R-G-B signal from the monitor. 2.6 Turn the Green Cut off Control (VR404) on the Neck Board fully CW. (See Fig. 3) 2.7 Turn the Red and Blue Cut off Controls (VR403 & VR405) fully CCW, 2.8 Pull the Deflection Yoke backward so that the Green belt will appear. (See Fig. 4) 2.9 Decrease the horizontal width of the raster, if necessary, in order to be able to see the right and left edges of the raster. 2.10 Move the two Purity Magnets with respect to each other in order to center the raster on the screen and the Green belt on the raster horizontally. Push the Deflection Yoke forward gradually and fix it at the place where the Green screen becomes uniform throughout. Turn the Cut off and Drive Controls and confirm that each color is uniform. 2.13 If the color is not uniform, re-adjust it moving the Purity Magnets slightly. Decrease the vertical size of the raster, if necessary, such that the top and bottom raster edges can be seen. 2.
2. s
2. B “cap (GRIDS No. 3AND 4) Pp ° s i t
° N
N
PURITY ADJ. REO/BLUE ADu. REO/SLUE ‘ON GREEN ADy,
RED/BLUE RED/BLUE ON GREEN 2 O'CLOCK 10 O'CLOCK
REAR CONCENTRIC view CONVERGER ASSY. SHOWN IN ZERO CORRECTION POSITION
PURITY PURITY
go'ctok——”—-3 o'ctack INDIVIOUAL TAB ROTATION FIGURE?
| vr4os—7 | vrao4 | *vRa03 |
| BLUE | GREEN | RED |
| CUTOFF | CUTOFF | CUTOFF. |
FIGURE 3
NECK BOARD
GREEN BELT
FIGURE 4
2.15 Rotate the Purity Magnets as a pair (without changing the angle of one magnet relative to the other) in order to center the raster on the screen vertically. 2.16 Readiust the raster to the desired vertical size. 2.17 Turn all three cut off controls fully counterclockwise (CCW). Slowly turn up (CW) the Red cutoff control until a Red raster is just barely visible. 2.18 Slowly turn up the Green and Biue cutoff controls such that their associated colors. mixing with the Red, results in a White or Gray raster. 2.19 Confirm that the white or gray color is uniform throughout the screen. 2.20 Insert a wedge temporarily as shown in Fig. 4 and adjust the angle of the Deflection Yoke. 3.0 STATIC CONVERGENCE ADJUSTMENT
4-Pole Magnets and 6-Pole Magnets are for static convergence.
3.1. A cross hatch signal should be connected to the monitor. A pair of 4-Poie Convergence Magnets Is provided and adjusted to converge the biue and red beams. (See Fig. 6) When the Pole opens to the left and right 45° symmetrically, the magnetic field maximizes. Red and blue beams move to the left and right.(See Fig. 5) Variation of the angle between the tabs adjusts the convergence of red and blue vertical lines. When both 4-Pole Convergence Magnet Tabs are rotated as a pair, the convergence of the red and blue horizontal lines is adjusted. A pair of 6-Pole Convergence Magnets is also provided and adjusted to converge the magenta (red + blue) to green beams. (See Fig. 6). When the Pole opens to the left and right 30° symmetrically, the magnetic field is maximized. Red and blue beams both move to the left and right (See Fig. 5). Variation of the opening angle adjusts the convergence of magenta to green vertical lines. When both 6-Pole Convergence Magnet Tabs are rotated as a pair, the convergence of magenta to green horizontal lines is adjusted. 3.2
3.3
3.4
3.5
FIGURE 6 GREEN GUN (S THE CENTER GUN. CONVERGE THE RED AND BLUE. THEN CONVERGE RED AND BLUE ON GREEN.
VERTICAL 4-POLE, CONVERGENCE {MAGNETS BLUE & RED
3.2
SLIDE MAGNETIC RING TABS TOWARD OR AWAY FROM EACH OTHER On
HORIZONTAL 4-POLE <> CONVERGENCE |MAGNETS BLUE & RED Jewe
33 REO
ROTATE BOTH MAGNETIC RINGS TOGETHER VERTICAL 6-POLE 4” > to CONVERGENCE |MAGNETS f BLUE & RED H ‘ON GREEN GRN | iRED/BLU
3.4 :
SLIDE MAGNETIC RING TABS TOWARD OR AWAY FROM EACH OTHER, ——~ HORIZONTAL 6-POLE CONVERGENCE |MAGNETS BLUE @ RED ON GREEN
3.5
ROTATE BOTH MAGNETIC RINGS TOGETHER L
REPEAT 3.2 6 3.3 IF ALL LINES ARE NOT CONVERGED AT CENTER
| Lg POLE convencence MAGNETS | a 9827
FIGURE 5
a ANODE CONTACT
ERGENCE 4 POLE CONVERGENCE MAGNETS MAGNET a: PURITY CENTERING MAGNETS, { ° Ey DEFLECTION YOKE
RUBBER WEDGES
4.0 PRECISE ADJUSTMENT OF DYNAMIC CONVERGENCE (See Fig. 7, 8 and 9)
4.2
4.3 Feed a cross hatch signal to the monitor. Insert a wedge temporarily and fix the Deflection Yoke so as to obtain the best circumference convergence (See Fig. 8 and 9)
2)
3)
4)
5)
&)
7) Tilting the angle of the yoke up and down adjusis the crossover of both vertical and horizontal red and blue lines. See Fig. 8 (a) and (b). Tilting the angle of the yoke sideways adjusts the parailel convergence of both horizontal and vertical lines at the edges of the screen See Fig. 9 (a) and (b). Use three rubber wedges (tapered rubber wedges are used for a purpose). The position of each rubber wedge is shown in Fig. 7. Do NOT force the permanent wedges in. They are to be inserted until they just make contact with the yoke—after the yoke has been positioned. Fix the three permanent rubber wedges with chioroprene rubber adhesive. After the adhesive has dried enough to hold the wedges in place, carefully remove the temporarily installed wedge.
UPPER \ RT pam
RGB UNDER Dog TEMPORARILY INSTALLED WEDGE
DEFLECTION YOKE
FIGURE 7
UPPER
Me CRT SCREEN (a) INSERT RUBBER WEDGE CRT SCREEN > INSERT RUSBER WEDGE FROM UPPER SIDE FROM LOWER SIDE
FIGURES yooe
CRT SCREEN INSERT RUBBER WEDGE CRT SCREEN INSERT RUBBER WEDGE
FROM LEFT SIDE FROM LOWER SIDE FIGURE 9
5.0 WHITE BALANCE
5.1
5.2 5.3
5.4
5.5
5.6 Refer to Fig. 2 and do the following in subdued light. Ground the R/G/B inputs. Set the R/G drive controls to their mechanical centers. Set the screen and R/G/B cutoff controls to minimum (fully CCW). Connect a jumper wire between TP301 and TP302 (located on the MAIN PCB) Slowly turn up (CW) the screen control until the first colored line becomes just barely visible. That color which has just appeared is referred to as the “iead” color. Do NOT turn its associated cutoff control—it must remain fully COW. Connect a DC oscilloscope to the collector of the ead color’s output transistor (Q401, Q402, or Q403) on the Neck PCB at TP47R, TP47G, or TP47B. 5.8
5.9
5.10
5.11 5.12 Adjust the black level control (VR201) to obtain the waveform shown in Fig. 10. Readjust the screen control such that the colored line is just barely visible. Slowly turn up the two remaining cutoff controls such that their associated colors, mixing with the lead color, results in a white or gray line. Remove the jumper wire. Adjust the Black Level Control for a dim raster. Touch up the two trailing cutoff controls (NOT the lead cutoff control) for best gray uniformity. Adjust the Black Level Control for a bright raster. Adjust the R/G drive controls, if necessary for best neutral white. Repeat steps 5.12 and 5.13 until good tracking of white balance is achieved.
BLANKING PULSES
FIGURE 10 140V
O-vbc
REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A* on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.
MAIN BOARD
| Ref. No. | Part No. | Description | Ref. No. | Part No. | Description |
RESISTORS RESISTORS (CONT.)
| R201 | 203X6500-645, | 1K Ohm, 5%, 1/4W Carbon | R369 | 203x5602-329 | 680K Ohm, 5%, 1/2W Comp. |
| F202 | 203X6500-523, | 30 Ohm, 5%, 1/4W Carbon | 370 | 203X6501.002 | 33K Ohm, 5%, 1/4W Carbon |
| R203, | 203X6500-405 | 4100 Ohm, 5%, 1/4W Carbon | R371 | 203X9014-584 | 1K Ohm, 5%, 1W Metal Oxide |
| R204 | 203X6700-327 | 100 Ohm, 5%, 1/2W Carbon | R372 | 203x9101-119 | 12K Ohm, 5%, 1W Metal Oxide |
| R205 | 203X6700-421 | 270 Ohm, 5%, 1/2W Garbon | R375 | 203X6700-763 | 6.8K Ohm, 5%, /2W Carbon |
| R208 | 203X6500-540, | 390 Ohm, 5%, 1/4W Carbon | R376 | 203x9104-404 | 270 Ohm, 5%, 2W Metal Oxide |
| R207 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R377 | 203x6500-447 | 150 Ohm, 5%, 1/4W Carbon |
| R208 | 203X6500-540 | 380 Ohm, 5%, 1/4W Carbon | R378, | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon |
| R209 | 340X2201-834 | 200 Ohm, 5%, 1/4W Carbon | R379 | 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon |
| R210 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R380 | 203X6500-865 | 8.2K Ohm, 5%, 1/4W Carbon |
| R211 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R381 | 203X6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide |
| R214 | 203X6500-645, | 1K Ohm, 5%, 1/4W Carbon | R383 | 203X9014-387 | 150 Ohm, 5%, 1W Metal Oxide |
| R215 | 203X6501-126 | 100K Ohm, 5%, 1/4W Carbon | R502 | 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon |
| R216 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R503 | 204X 1700-535 | 150 Ohm, 5%, 15W Metal Oxide |
| R217 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R504 | 203X8014-267 | 47 Ohm, 5%, 1W Metal Oxide |
| R218 | 203X8500-645 | 1K Ohm, 5%, 14W Carbon | R505 | 203X6501-209 | 2.2K Ohm, 5%, 1/4W Carbon |
| R219 | 203X6501-126 | 100K Ohm, 5%, /4W Carbon | R506 | 203X9104-105 | 15 Ohm, 5%, 2W Metal Oxide |
| R220 | 203X6500-645, | 1K Ohm, 5%, 1/4W Carbon | R507 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. |
| R221 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | AK RGO1 | 204X 1625-058 | 3.3 Ohm, 5%, 10W WW |
| R222 | 203X6500-762 | 3.3 Ohm, 5%, 1/4W Carbon | R701 | 203x9105-141 | 2.2 Ohm, 5%, 2W Metal Oxide |
| R224 | 203X8500-169 | 10 Ohm, 5%, 1/4W Carbon | R702 | 203X6206-441 | 2.2 Ohm, 5%, 1/2W Carbon |
| R225, | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | vR201 | 204x2070-072 | 2k Ohm-B Semi-Fixed |
| R226 | 203X6500-169 | 10 Ohm, 8%, 1/4W Carbon | R301 | 204X2070-084 | 5K Ohm-B Semi-Fixed |
| R227 | 203X6501-044 | 47K Ohm, 5%, 1/4W Carbon | VR303 | 204X2070-085 | 500 Ohm-B Semi-Fixed |
| R228 | 203X6500-645 | 1K Chm, 5%, 1/4W Carbon | R351 | 204x2070-072 | 2k Ohm-B Semi-Fixed |
| R229 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | R352 | 204X2070-072 | 2K Ohm Semi-Fixed |
| R230 | 203X6500-863, | 8.2K Ohm, 5%, 1/2W Comp. | |||
| R231 | 203x6500-863, | 8.2K Ohm, 5%, 1/2W Comp. | |||
| R232 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | |||
| F233 | 203X6500-468 | 180 Ohm, 5%, 1/4W Carbon | |||
| Road | 340X2820.934 | 82 Ohm, 5%, 14W Carbon | CAPACITORS | ||
| R235 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | C201 | 203x001 4-088 | 1000 uF, 18V, Electrolytic |
| R236 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | 202 | 202X7200-064 | 330 pF, 500V, Ceramic |
| R301 | 203X6500-508 | 270 Ohm,5%, 1/4W Carbon | 6203 | 202X7200-043 | 220 pF, 500V, Ceramic |
| 302 | 203X6500-863 | 8.2K Ohm, 5%, 1/4W Carbon | C204 | 302X7200-043. | 220 pF, 500V. Ceramic |
| R303 | 203X6500-863 | 8.2K Ohm, 5%, 1/4W Carbon | C205 | 203X0014-076 | 470 uF, *6V, Electrolytic |
| R304 | 203X6500-724 | 2.2K Ohm, 5%, /4W Carbon | C208 | 203x1810-149 | 0.1 uF, 125V Mylar |
| R305 | 203X6500-842 | 68K Ohm. 5%, 1/4W Carbon | C207 | 349X2232-109 | 022 uF, 100V Mylar |
| R306 | 203x6003-201 | 7.8K Ohm, 2%, 1/4W Carbon | 301 | 203X001 4-065 | 330 uF, SOV Electrolytic |
| R307 | 203X6500-825 | 5.6K Ohm, 5%, 1/4W Carbon | 302 | 203X1600-563, | 0.033 uF, 50V Mylar |
| R309 | 203X6500-965 | 22K Ohm, 5%, 1/4W Carbon | 303 | 203X0629-037 | 3.3 uF, SOV Electrolytic |
| R310 | 203X6500-988 | 39K Ohm, 5%, 1/4W Carbon | C304 | 203X1600-366 | 0.068 pF, 50V Mylar |
| R311 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C306 | 203x0412.012 | 2.2 uF, 16V Tantal |
| R312 | 203x9014-741 | 4.7K Ohm, 5%, 1/4W Carbon | 307 | 203X1600-634 | 0.033 UF, SOV Mylar |
| R313, | 204X 1450-537 | 1K Ohm, 5%, 5W Carbon | 308 | 203X0025-174 | 3.3 uF, S0V Electrolytic |
| R314 | 203X6500-481 | 220 Ohm, 5%, 1/4W Carbon | C303 | 203X1207-100 | 0.068 uF, 100V PP |
| R318 | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | 310 | 203X0629-061 | 10 UF, 100V Electrolytic |
| R316 | 203X6500-762. | 3.3K Ohm, 5%, 1/4W Carbon | C311 | 203X0041-025 | 10 uF, 160V Electrolytic |
| R317 | 203X6700-107 | 12 Ohm, 5%, 1/2W Carbon | 312 | 202X7050-248 | 1000 pF, 500V Ceramic |
| R318 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | 6313 | 203X0040-052 | AT uF, 160V Electrolytic |
| F319 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | 314 | 203X1201.265, | 0.033 uF, 200V PP |
| R320 | 203x6501-002 | 33K Ohm, 5%, 1/4W Garon | C315 | 203X0629-023 | + uF, 50V Electrolytic |
| R321 | 203X6501.224 | 270K Ohm, 5%, 12W Carton | C351 | 2030629023 | 1 uF, 60V Electrolytic |
| R322 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C352 | 203X0619-045, | 47 uF, 25V Electrolytic |
| R351 | 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon | 6363 | 203X1190-015, | 0.0082 pF, 50V Mylar-PP |
| R352 | 203X6500-785 | 3.9K Ohm, 5%, /4W Carbon | 0354 | 203X0619-045, | 47 uF, 25V Electrolytic |
| 35s. | 203X6501-088, | 68K Ohm, 5%, t/4W Carbon | C355 | 203X1600-366 | 0.0068 pF, 50V Mylar |
| R354 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C356 | 202X7050-483 | 0.01 UF, 500V Ceramic |
| F355 | 203x9205-143, | 6.8K Ohm, 5%, 3W Metal Oxide | 6359 | 202X8065-606 | 100 pF, 500V Ceramic |
| R358 | 203X5601878 | 56K Ohm, 5%, 1/2W Carbon | C360 | 202X7050-366. | 0.0033 pF, 500V Ceramic |
| R360 | 203X6500-561 | 470 Ohm, 5%, 1/4W Carbon | C361 | 202X7050-483 | 0.01 uF, 500V Ceramic |
| R361 | 203X8500-886 | 40K Ohm, 5%, /4W Carbon | C362 | 202X7203-032 | 0.01 uF, 50V Ceramic |
| R362 | 203X9014-645, | 1.8K Ohm, 5%, 1W Metal Oxide | B*C363 | 203x1270911 | 8700 pF, 1.5 KV PP |
| R363 | 204X1527-751 | 3.9K Ohm, 5%, 7W Metal Oxide | C365 | 203X1201-265 | 0.33 UF, 200¥ PP |
| R364 | 203X6500-246 | 22 Ohm, 5%, 1/4W Carbon | C366 | 203X0019-026 | 22 uF, 25V Electrolytic |
| R365, | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | C367 | 202X8065-162 | 6 pF, 500V Ceramic |
| R367 | 203x8500-886 | 10K Onm, 5%, 1/4W Carbon | C368 | 202X7203-032 | 0.01 UF, S0V Ceramic |
| R368 | 203X5802-185, | 330K Ohm, 5%, /2W Comp. | 372 | 203X 1207-125 | 0.1 uF, 100V PP |
P.C. BOARD LAYOUT
FIGURE 11 MAIN P.C. BOARD
P.c. BOARD LAYOUT
TOP VIEW
BOTTOM VIEW
FIGURE 12 NECK P.C. BOARD
MAIN BOARD (CONT.)
| Ref. No. | Part No. | Description | Ref. No. « | Part No. | Description |
CAPACITORS (CONT.) SEMICONDUCTORS (CONT.)
| 380 | 202x7200-087 | 470 uF, 500V Ceramic | 206 | 200X3181-523 | Transistor (NPN) 2SC1815GR |
| C501 | 203x1810-149 | 0.1 uF, 125V Mylar | Q207 | 200x3181-523 | Transistor (NPN) 2SC1815GR |
| 4 cs02 | 202X7050-282 | 1500 pF, 500V Ceramic | 208 | 200x3181-523 | Transistor (NPN) 28C1815GR |
| 4 6503 | 202X7810-214 | 2200 pF, 125V Ceramic | 209 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| A.c504 | 202X7810-214 | 2200 pF, 125V Geramic | 210 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| 505 | 203x0220075 | 560 uF, 200V Electrolytic | 301 | 200X3181-523 | Transistor (NPN) 25C1851GR |
| 0506 | 203x0040-034 | 22 uF, 160V Electrolytic | 302 | 200X3207-308 | Transistor (NPN) 2SC2073LBGL2 |
| C307 | 203X0041-057 | 47 uF, 160V Electrolytic | 2303 | 200%3207-308 | Transistor (NPN) 2SC2073LBGL2 |
| 701 | 203x0019-092 | 1000 UF, 25V Electrolytic | 351 | 200X3248.217 | Transistor (NPN) 28C2482BK |
| c702 | 203X0634-061 | 10 uF, 100V Electrolytic | 352 | 200X4589-802 | Transistor (NPN) 2SD898B |
| 703 | 202X7050-248 | 1000 pF, 500V Ceramic | ax ot | 200X2300-033 | IG HA11423 |
| ic501 | 200X2600-183 | IC STR381 |
SEMICONDUCTORS
| D203 | 201%2010-159 | Diode, 182076-27 | |||
| 0204 | 201X2010-159 | Diode, 1S2076-27 | TRANSFORMERS & COILS | ||
| D205 | 201X2010-159 | Diode, 1$2076-27 | L351 | BOIXATIOIS4 | Coll, (RF Choke) |
| D206 | 201x2010-159 | Diode, 18207627 | L352 | 201X5000-083 | Coll, Horiz, Size |
| 0207 | 201X2010-159 | Diode, 1$2076-27 | 701 | Pieaegand | Coll, Adg. |
| 0208 | 201%2010-189 | Diode, 18207627 | 1351 | 202X1300-080 | Transtormer, Hor. Drive |
| 209 | 201X2010-159 | Diode, 82076-27 | Ak 1352 | angnei2tg0 | HvUnlt, M11 |
| D301 | 201X2010-165 | Diode, 1$$81 | |||
| 302 | 201X2010-159 | Diode, 1$2076-27 | MISCELLANEOUS | ||
| 0303 | 201X2010-159 | Diode, 182076-27 | A\F501 | 204X7120-073 | Fuse, 4 Amp, 125V |
| 0304 | 201X2120.009 | Diode, RH-IV | 402 | 208X5008-632 | Recep W Wire 3P-M-BG |
| 0305 | 201%2 120.009 | Diode, RH:IV | P201 | 204X9600-466 | Plug, PWB 3P-J |
| D306 | 201X2010-159 | Diode, 182076-27 | P202 | 204x9601.477 | Plug, PWB 6P-Q |
| 0501 | 201x3120.216 | Diode, RM-1AV | P401 | 204X9600-298 | Plug, PWB 4P.B |
| 4.0502 | 201X3120-216 | Diode, RM-1AV | P501 | 204X9600.249 | Plug, PWB 2P-B |
| 4 0503, | 201X3120-216 | Diode, RM-1AV | P60 | 204Xx9600.304 | Plug, PWB 4P.C |
| 0504 | 201X3120-216 | Diode, RM-1AV | THEO1 | 201X0100-112 | Thermistor |
| D505 | 201X3120-216 | Diode, RM-1AV | |||
| D506 | 201X3120-216 | Diode, RM-1AV | |||
| D701 | 201X2 100-234 | Diode, RU2V | FINAL ASSEMBLY PARTS | ||
| D702 | 201X2120-009 | Diode, RH-1V | AX 88X0138-508 | 19VLTP22 Pix Tube | |
| 201 | 200x3181-523 | Transistor (NPN) 28C1815GR | 205X9800-158 | Lateral/Purity Assembiy | |
| 202 | 200x3181-523 | Transistor (NPN) 2SC1815GR | Av | 202X1111-201 | Yoke Deflection |
| 203 | 200%4056-260 | Transistor (PNP) 2SA562-Y-TM | 204X9301-255 | CRT Socket | |
| 204 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM | 291X5004-262 | Automatic Degaussing Coli Unit | |
| 205 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM |
NECK BOARD RESISTORS CAPACITORS
| Rao | 203x6000-729 | 220 Ohm, §% 1/4W Carbon | c401 | 202X7050-269 | 1200 pF, 500V Geramic | |
| R402 | 203x8500-540 | 390 Ohm, 5% 1/4W Carbon | c402 | 202X7050-248, | 1000 pF, 500V Ceramic | |
| R403 | 203X6000-661 | 820 Ohm, 5% 1/4W Garbon | C403 | 202X7050-248 | 1000 pF, 500V Ceramic | |
| R404 | 203X6000-729 | 220 Ohm, 5% 1/4W Carbon | C404 | 202X7050-282 | 1600 pF, 1.5KV Ceramic | |
| F405 | 203X6500540 | 390 Ohm, 5% 1/4W Carbon | C405 | 202X7050-483 | 0.01 uF, 500V Ceramic | |
| R406 | 203X6000-661 | 820 Ohm, 8% 1/4W Carbon | ||||
| Re07 | 203X6000-728 | 470 Ohm, 5% iW Carbon | ||||
| R408 | 203X6000-998 | 270 Ohm, 5% 1/4W Carbon | SEMICONDUCTORS | |||
| Lived | ooeeone 661 | 820 Ohm, 5% 1/4W Carbon | aot | 200X3206-800 | Transistor (NPN) 28C2068LB | |
| Reto | cosrato4sen | 15K:Ohmn, 5% 20... Forming | Qao2 | 200x3206-800 | Transistor (NPN) 28C2068LB | |
| nai | Ecce | 15K Ohm, 5% 2W M.0. | Forming | 403 | 200X3206-800 | Transistor (NPN) 28C2068LB |
| Ra12 | 203x9104-824 | 15K Ohm, 5% 2W M.O, | Forming | |||
| Ra13 | 203x6000-998 | 2.7K Ohm, 5% 1/2W Comp. | ||||
| Raid | 203X6000.998 | 2.7K Ohm, 5% 1/2W Comp. | ||||
| Rats | 203X6000-998 | 27K Ohm, 5% 1/2W Comp. | MISCELLANEOUS | |||
| Ra16 | 203X9 105-154 | 2.2 Ohm, 5% 2W Metal Oxide | oat | 206x509 296 | RECEP W Wire 4P-E: | |
| ; | P402 | 204X9600-254 | Plug, PWB 3P-A | |||
| R419 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | Hs | |||
| R420 | 203X6500-741 | 2.7K Ohm, 5% t/4W Carbon | 408 | Pongrectnetiads | Plug, Pin 1P-D | |
| : | P701 | 204x9601-020 | Plug, | PWB 4P-E | ||
| R421 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | iy | |||
| vRao1 | 204x2115-014 | 500 Ohm, -B Semi-Fixed | ||||
| vR402 | 204X2115.014 | 500 Ohm, -B Semi-Fixed | ||||
| vR403 | 204x2115-006 | 5K Ohm, -B Semi-Fixed | ||||
| R404 | 204x2115-006, | 5K Ohm: -B Semi-Fixed | ||||
| R405 | 204x2115-008 | 5K Ohm, -B Semi-Fixed |
ah
TYPICAL DC VOLTAGES
TERMINAL TRANSISTOR [termina COLLECTOR | BASE | EMITTER
15.4 14.0 15.5
41.4
DO NOT MEASURE
1.C. 501 PIN NO. { VOLTAGE VOLTAGE
19” COLOR MONITOR SCHEMATIC DIAGRAM MODELS 19K4901, 19K4906, 19K4951, 19K 4956 Power Supply Voltage and Symbols
| a OSCILLOSCOPE WAVEFORM PATTERN
| 45V_ | Vert. Osc | SERVICE | TECHNICIAN WARNING | The waveforms shown are as observed on the wide band | ||||||||
| CAUTION: | FOR | TIN | : | ||||||||
| ® | Syne | X-RAY RADIATION PRECAUTION: | peed ped Care | ERIeAE cen | oscilloscope with the monitor turned to a reasonably | ||||||
| Blanking | ~— | PONENTS ONLY WITH MANUFAC- | strong signal and a normal picture. The voltages shown | ||||||||
| CRT Cut-off | THIS PRODUCT CONTAINS CRITICAL | TURER’S RECOMMENDED PARTS. | on each waveform are the approximate peak ampli- | ||||||||
| tov | Hone | ©. | ELECTRICAL AND MECHANICAL PARTS | AVERTISSEMENT: | POUR MAINTENIR | tudes. | ||||||
| 0 | 3 | ae oe | ESSENTIAL FOR X-RAY RADIATION | NE RENPRCER Pe Poroehins | If the waveforms are observed on the oscilloscope with | ||||||
| Horz. Output | _. | PROTECTION. | DONT LE FONCTIONNEMENT EST | a poor high frequency response, the corner of the | |||||||
| Vert. Output | FOR REPLACEMENT PURPOSES, USE | CRITIQUE POUR LA SECURITE QUE PAR | puss wn tend i ne oo tigh Reauetoy- natse-ofl | ||||||||
| = | Y | TYPE | TS | SHI | IN | THE | DES PIECES RECOMMANDEES PAR LE | an | amplitude o} | igh | frequency |
| I | 175V | Video Output | ONLY | PARTS! SHOWN | Ity | FABRICANT, | tend to be less. |
351 COLLECTOR 940! 2402 9405 REQ OUT GREEN OUT give OUT 2SC2068.6/LBK 25C2068L8/ Bax 2520681 8/.5K| 2SCISIABVE/CVE 2SCIBIABVOEYE 25CISI4BYC/EVE
ue
1V/OIY 200uSECIDIV O.S/DIV SMSECIDIV
1.31 DC COUPLED 94023 BOTTOM LINE=0 VDC 02
o301 A300
| vy | _ | eae | ||||||
| SYNC. AMP | er | te | | : | |||||
| 2VIDIV 20OMSECIOIY | O.5IDIV 20u SECIDIV | escisisy, | 36T | |vese; (HOLD) ©. | é | | | Hee BEE | o3se, |
| | | Om, | fyesah | cay | tea | Se | ee | See | |
| LC. 301, PIN 3 | ILC. 301, PIN 15, | rd | FF | eee | asa! | b4_T | sok or | |
| He 47/2 | HOR. | RIVE | ve 352 | = | ||||
| i | lear? can | Tal | a | seise3t 2scraezen | yp | 260e9e8 |
wl | 3 i an = ’ 76 | (prores ron AVIDIV BMSECIDIV AVIDIV 20 SECIDIV
P82 TP-31, AC COUPLED “7 ais ae: sos)
| sear | " | ieee | 4b |
(eri | 9302 | ) veRrout | ot Nha )i2scao73 SYNC AMP vosc Hose © HAie23 5%
VERT)
| 20VIDIV SMSECIDIV | AVIDIV 200USEC/DIV | 2VIDIV 10uSECIDIV | | | eal |
LC. 901, PIN 13 Lox
| NEGATIVE SIDE OF C302 | F | © | gay | tT tee |
jes Fas vel] cae L188 Se TEE Tis ” 7 oan )\veRTouT vrs Le reer a mae gaa 390 15
| 1VOIV 200uSEC/OIV | 2VIDIV SMSEC/DIV | TVDIV 2MSECIDIV |
DEQAUSSING COIL * KagoID. K4906D, K4951D 5833 K4956
13 14
SERVICE NOTES
482 D.G.& Co.11-82 16 WGEC SERIES 194900 69x 1197 100
=
=
LIMITED WARRANTY
Myistar Electronics, Inc. warrants to the initial purchaser of the Mylstar Electronics, Inc. machine that the items listed in the following schedule as installed and used in the original Mylstar Electronics, Inc. machine will for the applicable period set forth in the schedule, computed from the initial date of purchase from an authorized Myistar Electronics, Inc. distributor, be free of defects in materials and workmanship:
SCHEDULE
GAME ITEM WARRANTY PERIOD
Pinball All Electronic 90 days
Printed circuit boards Pinball-Video —_—Alll Electronic 90 days Printed Circuit Boards Card Cage 90 days
Television 30 days
Monitor All Electronic 90 days Printed Circuit Boards
Monitor This Limited Warranty does not apply to any parts damaged in the course of handling or assembling by the customer or damage due to other than normal use or use in violation of instructions or reasonable practices, or further damaged in return shipment. This Limited Warranty is made only to the original customer, and is and shall be in lieu of all other warranties expressed or implied, and of all other obligations or liabilities on the part of Myistar Electronics, Inc. and in no event shall Myistar Electronics, Inc. be liable for any anticipated profits, consequential damages, loss of time, or other losses incurred by the customer in connection with the purchase or operation of Mylstar Electronics, Inc. machines or components thereof. The registration card with each Mylstar Electronics, Inc. factory-wired machine must be filled in and returned to Myistar Electronics, Inc. within ten days after date of purchase for this Limited Warranty to be effective. This Limited Warranty applies only to machines so registered. THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER-
CHANTABILITY OR FITNESS, AND OF ANY OTHER MYLSTAR
OBLIGATION ON THE PART OF THE SELLER AND ELECTRONICS MYLSTAR ELECTRONICS, INC. INC.
MYLSTAR
ELECTRONICS
INC.
165 West Lake Street Northlake, Illinois 60164 Tel (312) 562-7400 Telex 72-8463 ail mopetRecrea _ 7-83 A Columbia Pictures Industries Company