CATHODE RAY TOMES

Off Road Thunder 27in

Offroad Thunder (Midway Games, 2000) · Manual · 150 pages · 117 sections · original scan

Page 1

DECEMBER 1999 (DD MIDWAY 16-20035-101

Sit-In, Dedicated 27” Video Game

Operation Manual

e1-Setup ¢2-Operation 3-Audits e4-Wiring 5-Servicing 6-Troubleshooting _e7-Parts

@. Midway Games ine ., 3401 North California Avenue Cé

he 4 icago, ti nois 60618-5899 USA

Page 2

QUICK-START LINKING GUIDE

NOTICE: Before completing installation, verify that each cabinet has a separate and unique ID. Otherwise the link won’t function. For further information, see Linked Play Adjustments Menu in Chapter Three of the operation manual.

NOTICE: To link three or four cabinets, you must use an Ethernet hub.

}1.

14. SET UP THE LINKS

Switch off power to all cabinets. Remove cabinet access doors and linking cables. Check cabinet linking cables. One end of each linking cable must attach to the Arcade Computer’s network interface jack.

To link two cabinets: If you’re only linking two cabinets, use one coupler. You don’t need a hub. (You'll find a coupler in a Manila envelope, inside the cashbox.)

To link three or more cabinets: You need to add a hub to your network. Place the hub near the rear of the cabinets. Connect all linking cables. When you use a hub, don’t use any couplers.

Turn on cabinet power.

ADJUST GAME OPTIONS

CAUTION: Don’t connect or disconnect cables to the game electronics or hub with the power on. Otherwise, you may damage the electronics and void your warranty.

Find the diagnostic switches behind each cabinet’s coin door. Press and hold each cabinet’s TEST MODE button to enter the Menu System.

From each cabinet’s Operator Menu, select the Adjustments Menu.

From each cabinet’s Adjustments Menu, select the Linked Play Adjustments Menu.

LINKED PLAY. At each cabinet, set the LINKED PLAY option to YES.

UNIT ID. Each cabinet must have a unique unit ID. Set the option UNIT ID to a separate number for each cabinet.

EXIT the menu system. If you changed any unit IDs, turn off all machines.

RESTART ALL CABINETS. After the machines reinitialize, they'll operate in Linked Mode.

TEST THE SYSTEM. Test the network by playing a Linked Mode game on all linked machines.

Page 3

DECLARATION OF CONFORMITY

MIDWAY GAMES, INC.

3401 N. CALIFORNIA AVE. CHICAGO, IL 60618 U.S.A.

WE, HEREBY DECLARE UNDER SOLE RESPONSIBILITY THAT

THE MODEL: "OFFROAD THUNDER" 27": 20235, 20335, 20435, 20735, 20935, 21035, 21135, 21235, 21335, 21435, 21835, 21935, 22035, 22235, 22335, 27235

TO WHICH THIS DECLARATION RELATES IS IN CONFORMITY WITH THE FOLLOWING EUROPEAN PRODUCT SAFETY DIRECTIVES:

ELECTROMAGNETIC COMPATIBILITY DIRECTIVE (89/336/EEC AND AMENDMENTS 91/C162/08, 92/31/EEC ,93/68/EEC)

ELECTRICAL E MENT DESIGNED FOR USE WITHIN CERTAIN VOLTAGE LIMITS DIRECTIVE (73/336/EEC AND AMENDMENTS 88/C 168/02, 92/C210/01, 93/68/EEC,94/C199/03, 95/C214/02)

AS IS VERIFIED BY COMPLIANCE WITH THE FOLLOWING STANDARDS:

ENS55014: 1993 EN61000-4-2: 1995 IEC 801-3: 1984 (EN61000-4-3) EN61000-4-4: 1995 EN61000-4-5: 1995 EN335-1: 1995 TEC 335-2-82 (DRAFT)

Date issued: OCTOBER 27, 1999

CORPORATE V.P. OF QUALITY

Page 4

-iv-

Page 5

SETUP

yt Fill out and mail in the Game Information Card. Include the product serial number from the label 5 on the rear of the cabinet. For your records, write the product serial number in the manual.

SERIAL NUMBER

NOTICE: The term VGM refers to the video game machine.

Setup 1-1

Page 6

SAFETY INSTRUCTIONS

The following safety instructions apply to operators and service personnel. Read these instructions before preparing your VGM (video game machine) for play. Other safety instructions appear throughout this manual.

DEFINITIONS OF SAFETY TERMS

DANGER indicates an imminent hazard. If you fail to avoid this hazard, it will cause death or serious injury.
WARNING indicates a potential hazard. If you fail to avoid this hazard, it could cause death or serious injury.
CAUTION indicates a potential hazard. If you fail to avoid this hazard, it may cause minor or moderate injury. CAUTION also alerts you about unsafe practices.

NOTICE indicates information of special importance.

WARNING: TRANSPORTING VGMS. This VGM contains glass and fragile electronic devices. Use appropriate care when transporting this VGM. Avoid rough handling when moving the cabinet. Don’t move this VGM with the power on.
WARNING: DISCONNECT POWER. Always turn the power OFF and unplug the VGM before attempting service or adjustments. Installing or repairing PC boards with power ON can damage components and void the warranty. Be sure that you securely install ground wires.
WARNING: GROUND VGMS. Avoid electrical shocks! Don't plug in a VGM until you have inspected and properly grounded it. Only plug this VGM into a grounded, threewire outlet. Don’t use a “cheater” plug, or cut off the ground pin on the line cord. > @Pre
WARNING: HAZARD TO EPILEPTICS. A small portion of the population has a condition which may cause epileptic seizures or momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons experience seizures while watching some television pictures or playing certain video games. People who have not had seizures may nonetheless have an undetected epileptic condition.

If anyone in your family has experienced symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), consult your physician before using video games.

Parents should observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, discontinue use immediately and consult your physician.

Setup 1-2

Page 7
WARNING: AVOID ELECTRICAL SHOCKS. This video game machine does not utilize an isolation transformer. Internal, cabinet AC isn’t isolated from the external, AC line.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.
CAUTION: CHECK POWER SELECTOR. Set the 110/220VAC selector on the power supply for the correct line voltage. Check the selector setting before switching on the VGM.
CAUTION: USE PROPER FUSE. Avoid electrical shock! Replacement fuses must be of the same type as those they replace. Fuse voltage and current ratings must match ratings on the original fuse.
CAUTION: ATTACH CONNECTORS PROPERLY. Be sure that printed circuit board (PCB) connectors mate properly. If connectors don’t slip on easily, don’t force them. A reversed connector may damage your VGM and void the warranty. Connector keys only allow a connector to fit one set of pins on a board. ePPPLA @
CAUTION: TAKE CARE WHEN SHIPPING HARD DISKS. The hard disk drive must be packed in an anti-static bag. When shipping the drive for repair or replacement, pack it in an approved container (P/N 08-8068). Never stack or drop hard disk drives.

NOTICE: This manual is subject to change without notice. Midway reserves the right to make equipment improvements as engineering progress warrants.

PRODUCT SPECIFICATIONS Operating Requirements

Location Electrical Power Temperature Humidity

Domestic 120VAC @ 60Hz 4.0 Amps 32°F to 100°F Not to exceed 95% relative Foreign 230VAC @ 50Hz 2.0 Amps (0°C to 38°C) Japan 100VAC @ 50Hz 4.0 Amps

Cabinet Statistics Shipping Dimensions Cabinet Width 32.0" (81.3 cm) Depth 42" (169 cm) Height 76.0" (193 cm)

Equipment Characteristics Video Monitor Medium Resolution RGB 27” (63.5 cm) CRT Shipping Dimensions Seat Pedestal Width — 22.0” (55.8 cm) Depth 36.0” (91.4 cm) Height 51.0” (130 cm)

Audio System Digital Stereo Sound Two 5.5” (14 cm) and One 6.5” (16.5 cm) Spkr

Setup 1-3 Shipping Weight Cabinet Boxed, 360 Ibs. (163 kg.)

Seat pedestal Boxed, 125 Ibs. (56.8 kg.)

Currency Acceptors 2 Coin Mechanism, Coin Counter Dollar Bill Validator Ready Electronic Coin Acceptor Ready

Page 8

PRODUCT CONFIGURATION

¢ Standalone Units Each VGM (video game machine) is ready to play right out of the box. You can use the VGM Menu System to set player variables in advance. Or you can leave these choices to players.

Linked Units Linking allows players to compete against each other (on one course). Operator menus are the same as in stand-alone VGMs. With a coupler and linking cable, you can connect two VGMs. (You can connect up to four VGMs with the optional Hub Linking Kit.) You’ll find a coupler in the spare parts envelope. Look in the cashbox. The linking cable is factory installed.

INSTALLATION & INSPECTION

WARNING: The cabinets are top-heavy. While moving the cabinets, don’t push against plastic parts.

[] 4. Remove and set aside items from the shipping containers. Remove all packing material. Inspect for damage. Check the main cabinet exterior, the control section and the seat pedestal.

Remove the keys from the steering wheel. Unlock and open the coin, cash box, and rear doors. You'll find electrical cords, mechanical components, and VGM spare parts inside the cash box.

You can install an extra padlock to secure the rear door. You'll find a hasp in the spare parts bag. Remove the two lock bracket nuts from inside the cabinet, above the rear door opening. Slide the hasp onto the bolts. Now the hasp should protrude from the hole in back of the cabinet. Reinstall and tighten nuts.

CABINET SECURITY MODIFICATIONS

Modify the lock plate at the top of the rear door. Remove the bolts and nuts from the lock plate. Rotate the plate so that the slot will be above the door. Reinstall and tighten the bolts and nuts.

Setup 1-4

Page 9

[]5. Install one nut onto each leg leveler. Tilt the cabinet onto its side. Locate four threaded holes under the cabinet. Install a leveler and nut into each hole. Don't tighten the nuts yet.

[]6. _ Tilt the seat pedestal onto its side. Locate three threaded holes under the seat pedestal. Install a leveler and nut into each hole. Don’t tighten the nuts yet.

[]7. | Locate the caster wheel assemblies. Attach one caster onto each group of threaded studs. The cabinet uses four swivel casters. The seat pedestal uses three. Place the swivel caster in front. Place two locking casters in back. Tighten the caster mounting nuts very firmly.

INSTALL CASTERS AND LEVELERS

[]8. | Stand the cabinet upright and make certain that it rests in a stable position. Move cabinet to its play location. Maintain clearance between the cabinet and walls, drapes, other VGMs, etc. Lower each leg leveler until the cabinet is stable and level. Adjust the levelers to raise the wheels up off the floor. Distribute the cabinet’s weight equally on each corner. Tighten the leveler nuts.

[]9. Install the rear door. Close and lock this door. Leave the other doors open for now.

/

LOCATION OF SEAT PEDESTAL MOUNTING HOLES.

1-5

Page 10

]10. To protect seat pedestal mounting rails during shipment, the factory bolts them inside the cabinet. Remove the 1/4-20 hex-head bolts that secure the rails. Slide the rails partway out of the bottomfront cabinet opening. (See the nearby diagram for proper placement.)

]11. Fasten down the rails in this new position. Firmly tighten the rail bolts, but don’t torque them down. Slide the seat pedestal onto the rails. Vertically position the rails. Remove the seat pedestal. Tighten the rail bolts with a wrench.

NOTICE: When you install the seat pedestal, take care to avoid pinching wires!

]12. Roll the seat pedestal near the cabinet. Leave enough space to attach the wiring harness. Mate each seat pedestal cable connector with its cabinet cable connector. Press connectors firmly to seat contacts.

INSTALL THE LINE CORD

1-6 [] 13.

[] 14.

[] 15. Align the seat pedestal opening with the rail ends. Slide the seat pedestal forward onto the extended mounting rails. Align holes. Attach the seat pedestal using 1/4-20, tamper-resistant screws and large flat washers. You'll find a T27 wrench with the spare parts. Use it to tighten these screws firmly.

The power cord is in the cashbox. Match the holes on the IEC plug with the prongs in the receptacle. Push the plug firmly to seat it.

Before you plug in the VGM, verify line voltage compatibility with the machine. Then plug the VGM into a grounded (3-terminal) AC wall outlet. Switch on the VGM at the on/off switch. (This switch is on the cabinet roof. Face the cabinet’s back. Find the on/off switch to your right.) The VGM will power up and begin self-diagnostics. If diagnostics find no errors, the VGM enters Attract Mode. (Racing scenes and sounds, player scores, messages, etc.)

Page 11
  • Unlock and open the coin door. Locate the control switches. Press TEST MODE to enter the Menu System.
  • Select “DISK TESTS” at the Diagnostics Menu. Run all the tests in order to verify correct drive operation.
  • Select “SWITCH TESTS” at the Diagnostics Menu. Check to be sure that all control switches work.
  • Select “SOUND TESTS’ at the Diagnostics Menu. Verify operation of each speaker.
  • Select “FORCE FEEDBACK TESTS” at the Diagnostics Menu. Verify the presence of steering resistance.
  • Select “CALIBRATE CONTROLS” at the Main Menu. Set steering and throttle limits for maximum accuracy.
  • Select “START THE GAME” at the Main Menu. The system should enter Attract Mode. Open the coin door and press the SERVICE CREDITS button to allow game play. Press the START button to begin play. Listen to the audio while playing the game. Note sound irregularities (phase problems, no low frequencies, mono audio from stereo speakers, etc.). If necessary, check the wiring harness for internal shorts or strapped connections.
  • Change the volume and make adjustments as necessary. Close and lock all open doors. Tighten the leveler nuts. Engage the caster locks.

LINKED OPERATION

Equipment Requirements Linked Mode permits players to compete between networked cabinets in real time. The linking program is player selectable, so that each cabinet serves player needs.

To achieve linked operation, you must connect cabinets. The factory installs one linking cable in each cabinet.

e TO LINK TWO CABINETS, use a crossover coupler. All cabinets contain a crossover coupler to connect two cabinets together. Use only one coupler between each pair of cabinets. The coupler employs passive electronics. Passive electronics limit the cable length and number of cabinets that you can link. Most operations attach linked cabinets, but you can separate cabinets by up to 25 feet. You can add linked cabinet pairs as necessary. Link Two Cabinets with a Coupler

1-7

Page 12

Network Hub

Link Up to Four Cabinets with a Hub

TO LINK MORE THAN TWO CABINETS, use a network hub. Notice that the hub replaces the coupler between cabinets. Each hub can connect several cabinets. In fact, the hub’s active electronics permits use of large networks. You can add linked cabinets as necessary. The network hub’s active circuits also allow you to use long cables. Most operations attach linked cabinets, but you can separate cabinets by up to 300 feet.

THE DELUXE LINKING KIT (Model 25735) contains a lighted, overhead sign and cabinet connector brackets.

NOTICE: You can't link more than four cabinets.

Networking Pointers Protect exposed wiring from player foot traffic, cleaning crews, service personnel, etc. Use approved conduit or wire channels to support cables. Network modular connectors don't include strain relief.

Keep cables away from heat, moisture and electromagnetic fields. (Avoid neon signs, fluorescent fixtures, two-way radios, cordless telephones, power circuits, speaker wiring, etc.).

Universal RJ-45 modular plugs aren't keyed, numbered, or coded. Clearly mark cabinet network connections. Otherwise, someone could confuse them with computer or telephone circuits.

The factory supplies network cables with the cabinets. These cables will reach the hub in networks of four or fewer cabinets.

Use only Category 5, twisted pair cable.

If you want to monitor network activity, you can locate the hub remotely. You can use long cables, if they satisfy these requirements: (1) Cables must not exceed a length of 328 feet or 100 meters. (2) Cables must be Category 3 (or higher), 100 ohm, unshielded, twisted pair, communications-grade wiring. (3) You must not use standard telephone cables.

1-8

Page 13

Wiring the Network

NOTICE: Don't use crossover couplers in a hub installation. Otherwise, your network won't operate properly.

  • Raise the leg levelers. Roll the cabinets to their destination. Lower the leg levelers.
  • Verify VGM operation. Make necessary repairs or adjustments before making changes to the cabinets.
  • Shut down all machines.
  • Place the hub near the center of the linked cabinet array.
  • You'll find a linking cable coiled up inside each cabinet. Cut the cable tie. Locate the cable’s free end. Uncoil enough cable to reach the hub through the rear box of the cabinet.
  • Check the other end of the cable. It should attach to an Arcade Computer network jack. You'll find this jack in the middle cabinet box.
  • Recoil and retie the remainder of the cable. Repeat the cable connection steps at the other cabinets.
  • Plug the cabinet linking cables into any of the jacks on the hub rear panel.
  • Plug the hub’s AC power adapter into its jack on the hub.
  • Set the hub front panel switch to the LNK (link) position.
  • Retract excess cable into the cabinet coils so that the cables don't touch the floor. Retracting the cable keeps it away from cabinet wheels during relocation.
  • Connect the AC Adapter and line cords to AC power. Turn on each of the cabinets. Examine the screens of all cabinets.
CAUTION: Don't connect or disconnect cables to the VGM electronics or hub with the power on. Otherwise, you may damage the electronics and void your warranty.
  • Restart all machines.
  • The cabinets will begin the Power-On Self Test. If the test doesn’t find any errors, each cabinet enters its Attract Mode automatically.
  • Start up linked cabinets and ensure that each cabinet's player controls affect the same vehicle on all screens. The CPU and hub LEDS will indicate communication activity between the two cabinets.
  • Close and lock the coin doors. Reinstall and lock the rear cabinet doors. Lower all leg levelers until wheels lift off of the floor. Then level the cabinets.

Network Software Setup

  • Unlock the coin doors of all cabinets.

1-9

Page 14

Find the diagnostic switches behind each cabinet’s coin door. Press and hold each cabinet’s TEST MODE button to enter the Menu System.

From each cabinet’s Operator Menu, select the Adjustments Menu.

From each cabinet’s Adjustments Menu, select the Linked Play Adjustments Menu.

LINKED PLAY. At each cabinet, set the LINKED PLAY option to YES.

UNIT ID. Each cabinet must have a unique unit ID. Set the option UNIT ID to a separate number for each cabinet.

EXIT the menu system. If you changed any unit IDs, turn off all machines.

RESTART ALL CABINETS. After the machines reinitialize, they'll operate in Linked Mode.

TEST THE SYSTEM. Test the network by playing a Linked Mode game on all linked machines.

Page 15

)

OPERATION

NOTICE: The term VGM refers to the video game machine.

Oper:

Page 16

GAME OPERATION

STARTING UP Whenever you turn on the machine or restore power, the system executes boot ROM code. The boot ROM contains self-diagnostic tests. These tests automatically verify and report the condition of the CPU and other hardware. If the hardware fails a test, the system displays an error message.

Having passed power-up tests, the system enters Attract Mode. Attract Mode consists of typical game scenes and sounds, alternating with high scores. Attract Mode continues until game play commences.

Players insert currency or tokens to start the game. Each player selects a truck and a course. Play begins after a countdown period. The game will progress until players quit or exhaust their playtime. At Game- Over Mode, players may choose to begin again. If players choose not to continue, then the system returns to Attract Mode.

ARCADE COMPUTER This game uses an Arcade Computer to control its functions. The Arcade Computer is a customized personal computer. Housing the Arcade Computer is a PC-like case. Inside, you'll recognize the motherboard, plug-in cards, modular power supply, disk drives, etc. Despite these familiar features, Midway optimized this computer specifically for this game. The Arcade Computer design permits improved upgradability and service access without sacrificing ruggedness or reliability.

PLAYER CONTROLS

ACCELERATOR. The accelerator pedal controls vehicle speed and acceleration.

BRAKE. The brake pedal stops the vehicle, just like a real brake.

GEARSHIFT. The gearshift lever controls the amount of engine torque that reaches the wheels. The player may choose manual or automatic shift operation. Manual shift operation requires the player to upshift while accelerating and downshift while decelerating. (This shift has no reverse gear.) Players select automatic or manual shift trucks before racing. Manual shift trucks allow skilled drivers more control and faster starts.

e NITRO BUTTON. The NITRO button is on the end of the shift lever. If the nitro feature is active, pressing NITRO adds a power burst. (The button illuminates when nitro is available.)

« START BUTTON. The START button allows a player to begin or continue play, select courses and trucks, etc.

¢ STEERING WHEEL. The steering wheel aims the vehicle and provides course condition feedback.

« SLAM CAM. The red SLAM CAM button displays the cockpit view. The viewpoint is from the driver's seat inside the truck.

« CRASH CAM. The orange CRASH CAM button provides a close-up, aerial view of the course. The viewpoint is from above and behind the truck. A truck camera would see this view.

« CHOPPER CAM. The yellow CHOPPER CAM button provides a distant aerial view of the course. The viewpoint is from above and behind the truck. A tracking helichopper camera would see this view.

Operation 2-2

Page 17

Player Panel Controls

OPERATOR CONTROLS

CABINET CONTROLS

DIP Switches on the MagicBus™ Board set some system variables. These DIP switches are for factory use only. Keep them set at their default value, all off. You can adjust game variables, check bookkeeping totals and perform diagnostics with diagnostic control switches.

The Monitor Remote Control Board allows you to adjust the video display for optimum viewing.

The Cabinet POWER Switch turns off the game, but does not reset game variables.

The Computer POWER Switch turns off the computer. It is on the Arcade Computer. During service procedures, leave this switch on. Use the main power switch to control the power.

DIAGNOSTIC CONTROL SWITCHES,

The SERVICE CREDITS Button allots credits without changing the game's bookkeeping total. The Menu System occasionally assigns a function to SERVICE CREDITS. Check screen directions for these additional functions.

The TEST MODE Button causes the game to enter the menu system. To access the Menu System, press and hold TEST MODE until the Main Menu appears. Within the menu system, check screen directions for additional TEST MODE functions.

VOLUME DOWN and VOLUME UP Buttons set game sound levels. To make minor volume changes, press either button briefly. To make major changes, press and hold a button. In the menu system, VOLUME UP moves the item highlight bar up the menu. VOLUME DOWN moves the item highlight bar downward. Operation 2-3

Page 18

vy NOTICE: The Attract Mode volume level is separate from the Game Mode volume level. uy For greater profits, raise volume levels to add realism and draw attention to this game.

Operator Control Switch Locations

GAME FEATURES

GAME RULES

INSTRUCTIONS Play instructions appear on the left and right sides of the video monitor.

ONE PLAYER The player inserts currency or tokens to start the game. Next, the player chooses a truck and course and presses the START button. The game displays individual statistics periodically, during and after the race. Additional game information appears on screen as needed.

PLAYER CHOICES The player can drive any truck on any course. Each truck handles and performs differently. Players learn which trucks are best for a given course and driving style. Press one of the CAM buttons to select more trucks.

CONTROLLING A TRUCK The steering wheel, brake and accelerator control the truck. As in real trucks, the steering wheel directs the truck. The brake slows or stops the truck, and the accelerator sets speed. A NITRO button on the gearshift provides an extra burst of power. NITRO flashes to indicate nitro availability. Players must collect nitro icons along a course by steering directly under the icons. A gauge meters the amount of stored nitro.

INDICATORS Across the top of the screen, numeric indicators display truck statistics: A ghost image in the upper-left screen corner indicates shift type, manual or automatic. A meter in the top-left screen corner displays Operation 2-4

Page 19

engine RPM. A top-right gauge measures remaining nitro fuel. At the screen’s top-center, a digital clock times the current lap in seconds. As appropriate, the screen also flashes CHECKPOINT.

DISPLAYS The player’s vehicle appears at the center of the screen. The numbers floating above some vehicles indicate that other humans control them. (These are linked players.) The Arcade Computer controls trucks without numbers. At the bottom of the screen, another instrument displays relative positions of nearby trucks. The right side of the screen provides race statistics... e Position per number of trucks (for example, “1 "7 12”) e The number of cars ahead of the player (“9 cars ahead”) e A\lap timer for each lap (“0:2:00”) e Score box (only during scored game modes)

GAME ACTION Action begins after the “three-two-one” countdown. The announcer hollers “Go!” To continue play, the player must drive past each checkpoint within the time limit. To decrease time between checkpoints, players must avoid fixed obstacles and other trucks. Ramps allow players to advance more quickly, collect hovering nitro icons, or avoid obstacles. (Red nitro icons contain more fuel than blue nitro icons.)

Players can change their view of the action by pressing the view buttons. These buttons are on the left side of the control panel. Game sounds include announcer comments, engine noise, and other effects.

SCORING Players who set a speed record may enter their initials in the High Score Table. After a player completes a certain number of courses, he can choose additional courses. (Adjustments determine the number.)

HEAD-TO-HEAD RACING Networked cabinets offer players linked, head-to-head racing competition. Each player begins the courseselection process. A join-in message alerts subsequent players to the possibility of a linked race. If players don't begin their selection process before this message disappears, their races don't link. (Unlinked players compete in independent races, as usual.) Players may use the solo feature to decline a link.

If other players begin selection during the join-in message, the cabinets communicate over the network. Each additional cabinet sends out its own packet containing a unique unit ID. In return, each cabinet receives data from active cabinets. A "waiting" message indicates that other players are still selecting race options. Eventually, the last player finishes selecting or the waiting period ends. At this point, all linked players see the start screen simultaneously.

Latecomers can't participate in an ongoing linked race. They can begin an independent race. The link automatically terminates when the game is over. Players can then set up another link.

MAINTENANCE

¢ Cabinet and Seat Use plastic-safe, non-abrasive cleaners to avoid damage. Apply cleaner to a clean cloth or sponge. Use this to wipe the seat or cabinet. Don't apply cleaner directly to the artwork or cabinet!

e Player Controls Use plastic-safe non-abrasive cleaners to avoid damage. Apply cleaner to a clean cloth or sponge. Use this to wipe the player controls. Don’t apply the cleaner directly to the controls!

e Viewing Glass To clean the glass, you don’t need to switch off power to the game. Apply a mild glass cleaner to a clean cloth or sponge. Use this to wipe the viewing glass. Don’t apply the cleaner directly to the glass! Liquid could drip down into switch or motor circuits and cause erratic game operation.

Operation 2-5

Page 20

NOTES

Operation 2-6

Page 21

DIAGNOSTIC, AUDIT & ADJUSTMENT MENU SYSTEM

NOTICE: Information in this manual is subject to change without notice. Midway reserves tht rogr ints. yh right to make improvements in equipment function as progress warral

Diagnostic, Audit & Adjustment Menu System 3-1

Page 22

MENU SYSTEM

WHAT IS THE MENU SYSTEM? The game’s Menu System is a series of auditing, game adjustment and diagnostic screens. You can easily access and apply these screens to optimize game performance. For instance... « Use game audits screens to assess game performance.

« Use adjustment screens to help you to customize game performance. For instance, you can restore factory default game settings. You can also calibrate player controls for accuracy.

« Use diagnostic screens to verify proper equipment operation.

ACTIVATING THE MENU SYSTEM Open the coin door. Find the TEST MODE switch inside. Press TEST MODE to invoke the Menu System. The game system responds by exiting Game Mode and entering Diagnostic Mode. The system runs a brief self-test, and then displays the Operator Menu. The Operator Menu is the opening screen of the Menu System.

Game audits, adjustments and diagnostics are line items on the Operator Menu. Selecting an item opens its submenu. Every submenu presents various options that you may act upon.

MIDWAY

DIAGNOST I< MENU

AUDITS MENL

ADJUSTMENTS MENU

UTILITIES MENU

VOLUME ADJUSTMENT

CALIB TE STEERING,

TART THE GAME

OFF ROAD THUNDER 1999 Midway Home Entertainment Inc. All rights reserved. OFF ROAD THUNDER is a trademark of Midway Home Entertainment Inc. MIDWAY is a trademark of Midway Games Inc.

Press TEST to execute this command

OPERATOR MENU

MENU LAYOUT Menus differ, but related information tends to occupy the same screen locations. Diagnostic, Audit & Adjustment Menu System 3-2

Page 23

e The block at the top, center of each screen displays the current menu title.

« Data (menu items, video signals, statistics, reports, etc.) appears in the center of the screen.

« Game-operation information appears at the top-center of the screen, between logos.

« Messages (explanations, control functions, revision levels) display at the bottom of the screen.

MENU NAVIGATION CONTROLS Highlight a menu line item with the middle two diagnostic buttons inside the coin door. (Press VOLUME UP or VOLUME DOWN.) Select the option with the TEST MODE button. You can only select one highlighted item at a time. To return the game to play, first highlight START THE GAME. Then press TEST MODE. (This is the only menu that allows you to exit the Menu System.)

EQUIVALENT MENU NAVIGATION CONTROLS In most cases, certain player panel buttons duplicate the functions of the diagnostic buttons. You may find menu navigation easier with the player panel buttons. Here are the player panel functions within the Menu System...

Player Panel Button Function Equivalent Diagnostic Switch

NITRO

CHOPPER CAM

CRASH CAM

SLAM CAM

START Select a menu item

*Select a menu item eEnter Change Mode Move down the menu

Move up the menu

Various functions, including... ©To bottom of Operator Menu (None)

TEST MODE

VOLUME DOWN

VOLUME UP

SERVICE CREDITS (for some functions) eBack to Operator Menu *Cancel

AUTOMATIC TESTS Whenever you open the Menu System, the Power-On Self-Test (POST) activates. This routine runs automatically. It can detect faults that cause game or Menu System malfunctions. The Self-Test usually takes less than a minute. The test doesn’t display anything.

Diagnostic, Audit & Adjustment Menu System 3-3

Page 24

Operator Menu (continued) Diagnostics Menu

DIAGNOSTICS

Select DIAGNOSTICS MENU at the Operator Menu. The Diagnostics Menu helps you to verify the electrical and electronic condition of the game.

Highlight a line item with the middle two diagnostic buttons inside the coin door. Select the option with the TEST MODE button.

MIDWAY

SWITCH TEST

LAMP TEST

MONITOR PATTERNS MENU

SOUND TEST

RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

DIAGNOSTICS MENU

Diagnostic, Audit & Adjustment Menu System 3-4

Page 25

Operator Menu (continued) Diagnostics Menu (continued) Switch Test Menu

SWITCH TEST

Select SWITCH TEST at the Diagnostics Menu. Use the Switch Test to verify crossed wires, intermittent conditions, and stuck switches.

Operate the switch and watch the screen display. After completing tests, press TEST MODE three times to return to the Diagnostics Menu.

MIDWAY

CHASE CAM CHO FER CAM N. |

ZERO

BRAKE

Press TEST 3 times to return to previous menu

SWITCH TEST SCREEN

BUTTON TESTS check player and Diagnostic switches, such as CREDIT, TEST and SLAM CAM. Activate each button, and the screen indicator changes state. (Gray means off and green means on.) Release the button and the indicator returns to its previous state. A single indication on the screen should exactly duplicate each button change.

THE WHEEL TEST indicates the steering wheel position with a moving bar on a graph. The screen also displays a wheel position number. This number varies between zero (full left) and 255 (full right).

THE GAS TEST indicates the gas pedal position with a moving bar on a graph. The screen also displays a pedal position number. This number varies between zero (full back) and 255 (full forward).

THE BRAKE TEST indicates the brake pedal position with a moving bar on a graph. The screen also displays a pedal position number. This number varies between zero (full back) and 255 (full forward). Diagnostic, Audit & Adjustment Menu System 3-5

Page 26

Operator Menu (continued) Diagnostics Menu (continued) Lamp Test Menu

LAMP TEST

Select LAMP TEST at the Diagnostics Menu. The Lamp Test allows you to check operation of game lamps. Use the test to check for burned-out bulbs, faulty lamp wiring, etc.

Highlight a test with the middle two diagnostic buttons inside the coin door. Select the option with the TEST MODE button. Pressing TEST MODE also lights the selected lamp.

MIDWAY

UPPER ON

LOWER ON

cam ON

CHASE CAM ON

CHOPPER CAM ON

START

NITRO

TACHOMETER ;PEEDOME TER it

ALL LIGHTS

RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

LAMP TEST SCREEN

Lamp tests indicate the condition of game lamps. These include lamps in the control panel and overhead linking sign or optional header. (Unless your cabinet has header lights, the Leader Upper and Leader Lower tests have no effect.)

For most tests, select a lamp name from the menu. Press TEST MODE (or CHOPPER CAM) to turn on the selected lamp. Press TEST MODE again to toggle the lamp off. The Tachometer and Speedometer tests operate slightly differently. These tests lights one LED for each press of TEST MODE. Press START, SLAM CAM or CRASH CAM to exit. Select ALL LIGHTS to switch on all controlled lamps simultaneously.

After completing tests, select RETURN TO PREVIOUS MENU. This action closes the Lamp Test Menu and reopens the Diagnostics Menu. Diagnostic, Audit & Adjustment Menu System 3-6

Page 27

Operator Menu (continued) Diagnostics Menu (continued) Monitor Patterns Menu

MONITOR PATTERNS TEST

Select MONITOR PATTERNS at the Diagnostics Menu. The Monitor Patterns routine provides test screens to verify monitor performance or make adjustments.

Highlight a test with the middle two diagnostic buttons inside the coin door. Select the option with the TEST MODE button.

NOTICE: Use an industrial-grade degaussing coil before attempting monitor adjustments.

MIDWAY

COLOR BAR

ROSS HATCH

RED

BLUE

GREEN

WHITE

BLACK

5@% G

GRAY

RETURN TO PREVIOUS MENU

Press TEST to retu to previous menu

MONITOR PATTERNS MENU

Color Bars paint colored stripes on the screen. Use the color bars to help you to check or adjust monitor brightness and contrast. The color bars also expose defects in horizontal linearity. Each color bar consists of 16 intensity levels. On a properly adjusted monitor, the top 15 of these levels are visible. Each bar should appear sharp, clear, and distinct from bars on either side. Incorrect adjustment can cause missing detail at the top or bottom of a bar. Bent bars indicate horizontal linearity flaws, such as pie crust, pincushion or barrel distortion. (Correct color bar colors, left to right: Green, Red, Blue, Black, White,

Diagnostic, Audit & Adjustment Menu System 3-7

Page 28

Yellow, Magenta, Cyan.) Set controls as follows: 1. Adjust BRIGHTNESS and CONTRAST to minimum. 2. Turn up BRIGHTNESS until the pixels in the black stripe begin to glow (turn dark gray). 3. Bring up the CONTRAST control until you can see 15 bars. Then increase the contrast until you can’t distinguish a difference between the top two bars.

Crosshatch Patterns consist of an on-screen grid and a series of dots. Crosshatch Patterns help you to check or adjust several monitor parameters: These parameters include convergence, linearity, active viewing area and dynamic focus. The grid and the dots should be all white in color, with no fringes or parallel images. The lines should be straight and the dots round. For more detail on these adjustments, consult service literature from the monitor manufacturer.

Color Screen tests fill the screen with 100% of the chosen color at normal intensity. The Color Screen tests help you to check or adjust monitor intensity, black level, blanking and color purity. Each screen should be absolutely uniform from top to bottom and side to side. No retrace lines or noise should be visible. Color Screens may not hold their uniformity if the monitor degaussing circuit is defective.

If tests indicate a need for adjustment, use controls on the Monitor Remote Adjustment Board. You can make other adjustments from the back of the monitor.

White, Gray, and Black Screens fill the screen with black, gray or white at various intensities. These monochrome screens help you to check or adjust monitor convergence, purity, contrast and intensity. These screens also simplify black level and color gun control settings. The screens should be uniform with no color tints or distortion. No retrace lines or noise should be visible.

If tests indicate a need for adjustment, use controls on the Monitor Remote Adjustment Board.

Diagnostic, Audit & Adjustment Menu System 3-8

Page 29

Operator Menu (continued) Diagnostics Menu (continued) Sound Test Menu

SOUND TEST

Select SOUND TEST at the Diagnostics Menu. The Sound Test verifies the operation of the sound hardware and speakers. Use the Sound Test to find crossed connections, incorrect phase, rattles, vibration, distortion, etc. The Sound Test screen reports information, but doesn’t permit changes.

Increase the master volume level before beginning this test.

Highlight a test with the middle two diagnostic buttons inside the coin door. Select the option with the TEST MODE button. Selecting also activates a sound tone. The tone continues to play until you once again press TEST MODE.

MIDWAY

BEEP FRONT SPEAKER BEEP RIGHT SPEAKER » RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

SOUND TEST SCREEN

After choosing a speaker name, listen to the audio tone from that speaker. Only the specified speaker should produce sound. The other speakers should remain silent.

To exit the Sound Test Menu, highlight RETURN TO PREVIOUS MENU. Then press TEST MODE.

Diagnostic, Audit & Adjustment Menu System 3-9

Page 30

Operator Menu (continued) Audits Menu

AUDITS MENU

Select AUDITS MENU at the Operator Menu. The Audits Menu permits you to review game play statistics. Additional menus provide detailed reports for each player position on game starts, ends, cabinet abuse, fault conditions, etc.

Highlight a line item with the middle two diagnostic buttons inside the coin door. Select the option with the TEST MODE button.

MIDWAY

CRITICAL DITS

M AUDITS

PLAYER AUDITS

AUDITS BY TRACK

AUDITS BY TRUCE

>» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

GAME AUDITS MENU

Use the auditing information to help you to keep records of the game’s popularity and earnings. You may also analyze favorite tracks, most frequently used vehicles, and other statistics. These screens report information, but don’t permit changes.

Examine and record all game audit values before doing service or making repairs on this game.

NOTICE: Take care when clearing audit information. You can’t restore cleared data. If your audit data is important to you, back it up before proceeding. Use the OPTION SAVE AUDITS TO FLOPPY DISK on the Utilities Menu. To clear audits, use the Utilities Menu.

Diagnostic, Audit & Adjustment Menu System 3-10

Page 31

Operator Menu (continued) Audits Menu (continued) Critical Audits Menu

CRITICAL AUDITS

Select CRITICAL AUDITS at the Audits Menu. The Critical Audits Menu reports general information about coin counts and game use. This menu reports information, but doesn’t permit changes.

MIDWAY

CRITICAL AUDITS

CREDITS

PARTIAL CREDITS

BONUS CREDITS

GAME IN PROGRESS DURING LAST SHUTDOWN: NO

TIME SINCE LAST POWER-ON: 2 DAYS, 20:36:35

Press TEST or CREDIT to return to previous menu

CRITICAL AUDITS MENU

CREDITS and PARTIAL CREDITS permit you to assess currency collection. The other items present information on game operation.

BONUS CREDITS. A running total of bonus credits that the video game awarded to players.

GAME IN PROGRESS DURING LAST SHUTDOWN. Was the machine in Game-Play Mode when it entered Diagnostic Mode? This function answers the question.

TIME SINCE LAST POWER-ON. This function measures the period between power-ups. The clock starts counting whenever you switch off the video game machine.

Diagnostic, Audit & Adjustment Menu System 3-11

Page 32

Operator Menu (continued) Audits Menu (continued) System Audits

SYSTEM AUDITS

Select SYSTEM AUDITS at the Audits Menu. The System Audits Menu reports general information about coin counts and game use. Coin Audits is a read-only screen.

To exit, press TEST MODE.

MIDWAY

SYSTEM AUDITS POWER ON TIME RACE TIME LINKED RACE TIME POWER ON TIME SINCE LAST RESET RACE TIME SINCE LAST RESET NUMBER OF RESETS NUMBER OF WATCHDOG RESETS NUMBER OF GAMES SINCE WATCHDOG RESET NUMBER OF GAMES SINCE PREVIOUS WATCHDOG RESET NUMBER OF DEMOS SINCE LAST GAME NUMBER OF LOST PLAYERS DURING A RACE NUMBER OF LOST LINKS DURING A RACE NUMBER OF RE-LINKS NUMBER FOR OUT OF SYNC GAMES LEFT COIN COUNT RIGHT COIN COUNT FOURTH COIN CO! BILL COUNT SERVICE CREDITS FREE CREDITS eoocooecoCaCo0D

Press TEST or CREDIT to return to previous menu

SYSTEM AUDITS MENU

The System Audits Menu reports total quantities of coins, bills or credits collected by each active device. The menu does not calculate the value of the collected currency.

This menu reports information, but does not permit you to make changes. To reset the coin, bill, and credit counters to zero, use the Clear Audits menu.

We recommend that you examine and record audit information before you make changes. Once you’ve cleared the counters, you can’t retrieve the previous data from the system.

THE COIN COUNT AND BILL COUNT items help you to assess currency collection. The other items present information on game operation.

RESET, LINK, AND SYNC statistics are measures of the game software’s ability to recover from conditions that adversely affect game play.

Diagnostic, Audit & Adjustment Menu System 3-12

Page 33

Operator Menu (continued) Audits Menu (continued) Player Audits Menu

PLAYER AUDITS

Select PLAYER AUDITS at the Audits Menu. The Player Audits Menu displays additional information about player statistics and ability. This information assists you in understanding game use and profitability. Player Audits is a read-only screen.

MIDWAY

Press TEST or CREDIT to return to previous menu

PLAYER AUDITS MENU

GAMES PLAYED. Total number of games that players played on this machine.

CONTINUES. Total number of games on this machine that players paid to continue.

FREE GAMES WON remains at zero if you turn off the bonus and award options. Refer to the General Adjustments Menu for the bonus and award options settings.

STARTS. Number of games that players started.

FREE GAMES %. Proportion of games that were free, expressed as a percentage.

TIME EXPIRES. Number of times that time expired before a player completed the game.

DID NOT FINISH. Number of incomplete games.

FINISHES. Number of completed games.

TWO, THREE AND FOUR-PLAYER RACES remain at zero if no other games are linked to this one. Diagnostic, Audit & Adjustment Menu System 3-13

Page 34

Operator Menu (continued) Audits Menu (continued) Track Audits Menu

TRACK AUDITS

Select TRACK AUDITS at the Audits Menu. The Track Audits Menu includes specific information about player choices and ability. This is a read-only menu.

MIDWAY

AUDITS

@ @

a @ e @

SELECTED WINNER 0 0 Outlaw General Thrasher Silver Streak Snake Eyes Chieftan Bad Omen Nitro Ninja Wilcat Dust Devil Stinger ecooce0ccC0O

Use YVOL+ or TEST to view next page; CREDIT to return to previous menu

TYPICAL TRACK AUDITS MENU

These audits cover several screen pages. The name of the track appears at the top of the page. Press the VOLUME UP or VOLUME DOWN buttons to move through these pages.

Diagnostic, Audit & Adjustment Menu System 3-14

Page 35

Operator Menu (continued) Audits Menu (continued) Truck Audits Menu

TRUCK AUDITS

Select TRUCK AUDITS at the Audits Menu. The Truck Audits Menu gives you specific information about player choices and ability. This is a read-only menu.

Menu software includes several pages of audits. The name of the vehicle appears at the top of each menu page. Press the VOLUME UP or VOLUME DOWN buttons to navigate through these pages.

MIDWAY

t] a [7] 7] e

i] 7] e @ :8G :68 @ 286 788

Use VOL+ or TEST to view next page; CREDIT to return to previous menu

TYPICAL AUDITS BY TRUCK SCREEN

Diagnostic, Audit & Adjustment Menu System 3-15

Page 36

Operator Menu (continued) Adjustments Menu

ADJUSTMENTS MENU

Select ADJUSTMENTS MENU at the Operator Menu. The Adjustments Menu allows you to set game and player variables. Use these screens to optimize game performance and earnings.

Highlight an option with the middle two diagnostic buttons inside the coin door. Select the option with the TEST MODE button.

MIDWAY

GENERAL ADJUSTMENTS MENU

LINKED —-PLAY ADJUSTMENTS MENU

TRACK DIFFICULTY ADJUSTMENTS MENU

PRICING MENU

VOLUME ADJUSTMENT

FORCE FEEDBACK ADJUSTMENT

CALIBRATE STEERING, GAS AND BRAKE

SET TIME AND DATE

RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

ADJUSTMENTS MENU

Diagnostic, Audit & Adjustment Menu System 3-16

Page 37

Operator Menu (continued) Adjustments Menu (continued) General Adjustments Menu

GENERAL ADJUSTMENTS MENU

Select GENERAL ADJUSTMENTS MENU at the Adjustments Menu. At the General Adjustments Menu, you set the cabinet type, game display and measurement system. General Adjustments Menu options also control the cost and type of play.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

MIDWAY

E PLAY OFF RACE FOR 1S YES FREE RACE FOR 1 <LINKED> 2 PLAYERS SHOW MILES PER HOUR YES ADULT MODE ON

RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

GENERAL ADJUSTMENTS MENU

FREE PLAY determines whether the game accepts money for play, or allows operation without charge. For free play, turn this option on. For paid play, turn this option off (the factory default).

FREE RACE FOR 15° permits a free game for players who finish in first place. To award a free race to a first-place finisher, turn this option on. To eliminate the free race award, turn this option off. The factory default is on.

FREE RACE FOR 15" (LINKED). This feature awards a free game to the first place finisher among human players. The feature only operates when a minimum number of players join in. To award a free race toa first-place finisher, turn this option on. To eliminate the free race award, turn this option off. Available settings include 2, 3 or 4 players, or off. The factory default setting is off.

Diagnostic, Audit & Adjustment Menu System 3-17

Page 38

SHOW MILES PER HOUR sets the measurement system for display on game screens. To display speed in kilometers per hour, turn SHOW MILES PER HOUR off. To display speed in miles per hour, turn SHOW MILES PER HOUR on (the factory default).

ADULT MODE. When you enable Adult Mode, the glamorous cheerleaders appear in bikinis. When you disable Adult Mode, the cheerleaders appear in more conservative attire. The default setting is on.

Diagnostic, Audit & Adjustment Menu System 3-18

Page 39

Operator Menu (continued) Adjustments Menu (continued) Linked-Play Adjustments Menu

LINKED PLAY ADJUSTMENTS MENU

Select LINKED PLAY ADJUSTMENTS MENU at the Adjustments Menu. The Linked Play Adjustments Menu allows you to set the game cabinet network identity. After you cable the linked cabinets, use this menu to set up linked play.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

FREE PLAY LINKED PLAY ENABLED UNIT ID (1-4): 1 MIDWAY

LINKED—PLAY ADJUSTMENTS MENU

LINKED Pl ON UNIT ID ¢1-4) UNIT #1

» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

LINKED-PLAY ADJUSTMENTS MENU

Before proceeding, bring up the Linked Play Adjustments Menu on all linked cabinets.

LINKED PLAY. After you link a cabinet to other games, turn on LINKED PLAY. Now game electronics can communicate with other cabinets. To prohibit linked play, turn off the feature. The factory default is off.

UNIT ID determines the game’s address. Each linked game must have a unique number. Never use the same address for two cabinets. Sequence isn’t important. The factory default ID is 1.

REINITIALIZE. After selecting the ID, exit the Menu System. Shut down each linked cabinet for one minute. (Leave the computers switched on.) Then restore power to all cabinets. The cabinets should initialize in Linked Mode. Verify linked operation by playing some linked games. Diagnostic, Audit & Adjustment Menu System 3-19

Page 40

Operator Menu (continued) Adjustments Menu (continued) Track Difficulty Adjustments Menu

TRACK DIFFICULTY ADJUSTMENTS MENU

Select TRACK DIFFICULTY ADJUSTMENTS MENU at the Adjustments Menu. From the Track Difficulty Adjustments Menu, you set how much skill players need to complete races.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

MIDWAY

LIMIT FREE RACES TO 157 BONUS STAR E @ sec. BONUS CHECKPOINT TIME @ sec.

ADJUST TRACK DIFFICULTIES MENU

RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

TRACK DIFFICULTY ADJUSTMENTS MENU

LIMIT FREE RACES TO (LFRT) is the award cutoff point. LFRT prevents expert players from monopolizing a cabinet. The range is 1 to 100%. The factory default is 10%.

BONUS START TIME. You can use this feature to award several seconds of extra time to starting players. The factory default is zero seconds.

BONUS CHECKPOINT TIME. Use this feature to award several seconds of extra time as players pass checkpoints. The factory default is zero seconds.

ADJUST TRACK DIFFICULTIES MENU allows you to modify the level of challenge that each track poses.

Diagnostic, Audit & Adjustment Menu System 3-20

Page 41

Operator Menu (continued) Adjustments Menu (continued) Track Difficulty Adjustments Menu (continued) Adjust Track Difficulties Menu

ADJUST TRACK DIFFICULTIES MENU

Select ADJUST TRACK DIFFICULTIES MENU at the Track Difficulty Adjustments Menu. From the Adjust Track Difficulties Menu, you modify the level of challenge that each track poses. You can also increase or reduce starting and checkpoint bonus time. Difficulty and bonus default values are all zero.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Press TEST MODE to save changes and exit the variable. Or press TEST CREDITS to cancel changes and exit the variable.

You'll notice that each option line has three columns of figures to change. The program lets you edit each column in turn. First you modify BASE DIFFICULTY, then START BONUS, and last, CHECKPOINT BONUS.

MIDWAY

CHECKPOINT BONUS

Tunnel Vision Over ‘N’ Under Air Time High Octane Carnie of Chaos Cliffhanger Double Barrel Alpine Air Tunnel Vision Mirror Over ‘N’ Under Mirror Airtime Mirror High Octane Mirror Carnie of Chaos Mirror Cliffhanger Mirror Double Barrel Mirror Alpine Air Mirror eccocoecCOOCOCCOSD

Press TEST to return to previous menu

ADJUST TRACK DIFFICULTIES MENU

Diagnostic, Audit & Adjustment Menu System 3-21

Page 42

Operator Menu (continued) Adjustments Menu (continued) Pricing Menu

PRICING MENU

Select PRICING MENU at the Adjustments Menu. The Pricing Menu contains options for selecting standard and custom currency combinations. The factory default is USA1.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable. Turning on Free Play disables Pricing Menu settings.

MIDWAY

ING MENU

TOM PRI< > CURRENT PRICING:

STANDARD PRI<

DEFAULTS

>» RETURN TO PREVIOUS MENU

MIN UNI

OUNT NT

Press TEST to return to previous menu

PRICING MENU

SELECT CUSTOM PRICING allows you to set coin and credit options manually. Use this option to create your own pricing schemes. This menu permits changes to default values.

SELECT STANDARD PRICING allows you to select from several ready-made price schemes This menu permits changes to default values.

RESET TO DEFAULTS returns the price settings to factory default values. This menu permits changing all current values at once.

Diagnostic, Audit & Adjustment Menu System 3-22

Page 43

Operator Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Select Custom Pricing Menu

SELECT CUSTOM PRICING MENU

Choose SELECT CUSTOM PRICING at the Pricing Menu. The Select Custom Pricing Menu permits you to program and use your own pricing table. You can save several pricing schemes and chose between them as desired.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

MIDWAY

-RICING o

MIN UNIT

DITS STAR

DITS CONT INUE

F BILL

SHOW CREDIT FRACTIONS

COUNT COUNT =] n 80089 7 98 88 8 88 888°

; ‘i « N COIN COUNT

ENCY DOLLAR

ETURN TO -EVIOUS MENU

Press TEST to return to previous menu

TYPICAL SELECT CUSTOM PRICING MENU

The Custom Pricing Menu employs the same terms that appear on the Current Pricing Table. See the table below for definitions of these terms.

Diagnostic, Audit & Adjustment Menu System 3-23

Page 44

PRICING MENU TERMS SCREEN TERM DISCUSSION Slot Units; Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism Bill Validator (DBV) or bill acceptor. For instance, ifa quarter buys 1 unit, then $1 buys 4 units. (See Coins Units per Bill.) You insert a coin into a 1-unit coin acceptor. The system, due to its programming, knows that your coin is worth one unit. Units per Credit How many units equal one credit. (Units buy credit, the price of one game.) Units per Bonus Units awarded when a player earns a bonus. Minimum Units Until this many units accumulate, the system awards no credits. Credits to Start Number of games a player must purchase to begin play. Credits to Continue Number of games a player must purchase to resume play. Max Credits Limits the number of credits that the game will accept. Coins per Bill How many coins one bill is worth.

BASIC CUSTOM PRICING. Custom pricing creates an imaginary currency exchange. In this currency exchange, the coins of the realm are “units.” Think of units as a type of cyber-currency, useful only within the game software. By inserting coins, you purchase units.

Since units are only negotiable within game software, the system stores your units for you. When the system receives enough units, it buys a game for you. The price of a game is one “credit.” You can think of credits as a second form of cyber-currency.

Even though you’ve now bought one game, you may not be able to begin playing. In many pricing schemes, you must buy two or more credits to begin play. The idea here is something like a minimum order of goods at a store. That is, the operator can “shrink-wrap” two or more games in a package. You can’t play unless you buy the entire package.

1 /25¢ COIN; 1 CREDIT TO START. In a simple, quarter pricing scheme, the player inserts one coin to buy one unit. The system exchanges that unit for one credit. If CREDITS TO START contains the value one, then play commences. A dollar bill buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14114

e1 / 3 X 25¢; 2 CREDITS TO START. Again, assuming quarter slots, here’s one way to implement 75¢ pricing... In this scheme, each coin that the player inserts buys one unit. The system exchanges three units for one credit. CREDITS TO START contains the value two. To play, the player must pay for two credits. In this scheme, a dollar buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14324

2 / 1 COIN; 6 CREDITS TO START. Now let’s consider a more unusual pricing scheme. Here, the player can buy two units with one coin. The system exchanges each of these units for one credit. Notice that CREDITS TO START contains the value six. To play, the player must insert two more coins to pay for six credits. Also notice that if the player pays with a bill, the system throws in an extra unit.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
29164

Diagnostic, Audit & Adjustment Menu System 3-24

Page 45

Operator Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Select Standard Pricing Continent Menu

SELECT STANDARD PRICING CONTINENT MENU

Choose SELECT STANDARD PRICING at the Pricing Menu. The Select Standard Pricing Continent Menu allows you to choose the continent that you are operating in.

Highlight a line item with the middle two diagnostic buttons inside the coin door. Select the option with the TEST MODE button.

MIDWAY

NORTH AME ca

SOUTH AMERICA

EUROPE AZ2H

EUROPE 122

ASIA

AUSTRALIA

RETURN TO PREVIOUS

Press TEST to return to previous menu

STANDARD PRICING MENU

Diagnostic, Audit & Adjustment Menu System 3-25

Page 46

Operator Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Select Standard Pricing Continent Menu Select Standard Pricing Country for North America Menu

SELECT STANDARD PRICING COUNTRY FOR NORTH AMERICA MENU

Choose a continent (NORTH AMERICA, for example) at the Select Standard Pricing Continent Menu. The Select Standard Pricing Country for North America Menu contains options for selecting standard currency combinations. You may use standard pricing schemes as-is, or customize them.

Highlight a line item with the middle two diagnostic buttons inside the coin door. Select the option with the TEST MODE button.

MIDWAY

usa

CANADA

>» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

TYPICAL SELECT STANDARD PRICING FOR NORTH AMERICA MENU

Diagnostic, Audit & Adjustment Menu System 3-26

Page 47

Operator Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Select Standard Pricing Continent Menu (continued) Select Standard Pricing Country for North America Menu (cont’d) Select Standard Pricing Table for USA Menu (cont’d)

SELECT STANDARD PRICING MENU

Suppose that you want to set U.S. pricing. Choose USA at the menu entitled Select Standard Pricing Country for North America. This menu contains options for selecting standard U.S. currency combinations.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

MIDWAY

CURRENT PRICING: USA 3 LEFT UNITS 1

a

RETURN TO PREVIOUS MENU

Press TEST to execute this command

TYPICAL VIEW CURRENT PRICING DISPLAY

Diagnostic, Audit & Adjustment Menu System 3-27

Page 48

STANDARD PRICING TABLE

NAMESTARTCONTINUE [| CREDITS/COINCOIN’ [ COIN2[COINS | COINa[BILL
ANTILLES,221/25¢, 4G25¢1G,
AUSTRALIA 1221/3X20¢, 2/81.0020¢$1.00
AUSTRALIA 2221/5X20¢, 1/81.0020¢$1.00
AUSTRIA 122T/6Sch, 2A0Sch5Sch | 10 Sch
AUSTRIA 2221/2X5Sch, 3/2X10Sch5Sch__|10 Sch
BELGIUM221/20BF20BF| 20BF
BELGIUM 2223/20BF208F| 20BF
BELGIUM3222/20BF208F| 20BF
BELGIUMECA221/20BFspr| 208F | SBF
CANADA 122172x256, 3/8125e25¢
CANADA 2221/2x25¢,3/$125¢$1.00
CANADA 3223/$1.00, 6 / $2.00$1.00| $2.00
CANADA ECA221/2x25¢, 3/8125¢$1.00 | $2.00
DENMARK22B/SDKr, 7HODKrSDKr__|10DKr
FINLAND221/iFmk1Fmk__|5Fmk
FRANCE 1222ISFr, SOFTSFr10Fr
FRANCE 2212I5Fr, 4/10FrSFr10Fr
FRANCE 3211/5Fr, 3/10FrSFr10Fr
FRANCE 4211U5Fr, 2/10FSFr10Fr
FRANCE 5212I5Fr, SMOFr, 11/2 X 10FrSFr10Fr
FRANCE 6212ISFr, 4/10Fr, 9/2 X 10FrSFr10Fr
FRANCE 7211/5Fr, 3/10Fr, 7/2 X 10FrSFr10Fr
FRANCE 82115Fr, 2/10Fr, 5/2 X 10FrSFr10Fr
FRANCE 9211/3 X 1Fr, 2/5Fr1FrSFr
FRANCE 10211/2 X 1Fr, S/5Er1FrSFr
FRANCE 11211/3 X 1Fr, 2/5Fr, 5/2 X SFr1FrSFr
FRANCE 12211/2 X 1Fr, 3/5Fr, 7/2 X SFr1FrSFr
FRANCE ECA 4ii2IBFr, SOFTFrSFr10Fr20Fr
FRANCE ECA 2112I5Fr, 4/10Fr1FrSFr10Fr20Fr
FRANCE ECA 3111/5Fr, 3/10Fr1FrSFr10Fr20Fr
FRANCE ECA 4111/5Fr, 2/10Fr1FrSFr10Fr20Fr
FRANCE ECA 5112I5Fr, SMOFr, 11/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 6112ISFr, 4/10Fr, 9/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 7111/5Fr, 3/10Ft, 7/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 8111U5Fr, 2/10Fr, 5/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 9111/3 X 1Fr, 2/5Fr1FrSFr10Fr20Fr
FRANCEECA10 | 111/2 X 1Fr, S/SFr1FrSFr10Fr20Fr
FRANCEECA11| 111/3 X 1Fr, 2/5Fr, 5/10Fr1FrSFr10Fr20Fr
FRANCEECA12 | 111/2 X 1Fr, S/SFr, 7 0Fr1FrSFr10Fr20Fr
FRANCEECA13 | 111/10Fr, 2/20F, 4/30Fr1FrSFr10Fr20Fr
FREE PLAY===None| None| None | None | None.
GERMANY 122TID, 6/SDM1DM‘SDM
GERMANY 2214/1DM, 7/5DM1DM5DM
GERMANY 3211/1DM, 8/5DM1DM5DM
GERMANY 4211/1DM, 5/5DM1DM5DM
GERMANY 5211/1DM, 6/5DM1DM5DM
GERMANY ECA1 | 221/1DM, 2/2DM, 6/5DM1DM2DM5DM
GERMANY ECA2 | 211/1DM, 2/2DM, 6/5DM1DM2DM5DM
GERMANYECA3 | 111/1DM, 2/2DM, 6/5DM1DM2DM5DM
HUNGARY22T2X10Ft, S/2X2OFtT0Ft2OFt
ITALY221/500LItSo0Lt | S00Lit
JAPAN 1221100Yen100100
JAPAN 2222/100Yen100100
NETHERLANDS | 22TAHFI, 3/2.5HFITHFI2.5HFI
NEW ZEALAND 1 | 111/813t$2
NEW ZEALAND 2 | 112181St$2
NORWAY22SISNKr, 6/ONKrSNKr__[_10NKr
SPAIN 4227/100Pta, 6/500P ta700Pta_|500Pta
SPAIN 2221/100Pta, 5/500Pta100Pta_|500Pta
SWEDEN2AT/X1SKr, 2SKrSKr_|58Kr
SWITZERLAND T| 22T/ASFr, 6/5SFr1SFrSSFr
SWITZERLAND 2 | 221/ISFr, 7/5SFr1SFr5SFr
SWITZERLAND 3_|221/ASFr, 8/5SFr1SFr5SFr

(Table continues on next page)

Diagnostic, Audit & Adjustment Menu System 3-28

Page 49

STANDARD PRICING TABLE, continued

NAME START CONTINUE | CREDITS/COIN COIN 1 COIN 2 COINS COIN4 BILL UK ECA 1 1 1 1/50p, 3/£1.00 £1.00 50p 20p 10p £2.00 UK ECA 2 1 1 1/50p, 2/£1.00 £1.00 50p 20p 10p £2.00 UK ECA 3. 1 1 1/30p, 2/50p, 5/£1.00. £1.00 50p 20p 10p £2.00 UK4 1 1 1/50p, 3/£1.00 £1.00 50p UK5 1 1 1/50p, 2/£1.00 £1.00 50p UK ECA6 1 1 1/30p, 2/50p, 4/£1.00 £1.00 50p 20p 10p £2.00 UK ECA 7. 1 1 3/£1.00, £1.00 50p 20p 10p £2.00 UK ECA8 1 1 1/50p, 2/£1.00, 4/£2.00 £1.00 50p 20p 10p £2.00

USAT 2 2 1/25¢25¢ 25¢$1.00
USA2 2 1 1/25¢25¢ 25¢$1.00
USA3 1 1 1/25¢25¢ 25¢$1.00
USA4 1 1 1/50¢, 3/$1.0025¢ 25¢$1.00
USAS 2 1 1/50¢, 4/$1.0025¢ 25¢$1.00
USA6 1 1 1/50¢25¢ 25¢$1.00
USA7 1 1 1/50¢, 3/$1.0025¢ 25¢$1.00
USA8 2 2 1/50¢, 4/$1.0025¢ 25¢$1.00
USA9 3 2 1/25¢, 4/$1.0025¢ 25¢$1.00
USA10 3 3 1/25¢, 4/$1.0025¢ 25¢$1.00
USA11 4 2 1/25¢, 4/$1.0025¢ 25¢$1.00
USA12 4 3 1/25¢, 4/$1.0025¢ 25¢$1.00
USA13 4 4 1/25¢, 4/$1.0025¢ 25¢$1.00

USA ECA 3 3 1/25¢, 4/$1.00 $1.00 25¢ 10¢ O5¢ $1.00

Diagnostic, Audit & Adjustment Menu System 3-29

Page 50

Operator Menu (continued) Adjustments Menu (continued) Volume Adjustment Menu

VOLUME ADJUSTMENT MENU

Select VOLUME ADJUSTMENT at the Adjustments Menu. (You can also access this menu from the Operator Menu.) The Volume Adjustment Menu allows you to adjust relative sound loudness levels.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

MIDWAY

MASTER VOLUME | 40 ATTRACT VOLUME | 40

MINIMUM VOLUME ] 26

SOUND SAMPLE MUSIC 1

>» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

VOLUME ADJUSTMENT MENU

NOTICE: The Master Volume setting affects all other volume adjustments. You can still alter Attract sounds in relation to normal game sound. For example, suppose that you set Attract Mode volume to 50%. Then Attract Mode sounds are half as loud as normal game sounds.

NOTICE: Check the Master Volume setting before testing. Increase Master Volume to fully test speakers. Restore Master Volume to its previous level before returning to Game-Over Mode.

Diagnostic, Audit & Adjustment Menu System 3-30

Page 51

MASTER VOLUME sets the overall volume level during game play. This value simultaneously affects all other sound settings. The range is 1 to 100%. The factory default is 60%.

ATTRACT VOLUME adjusts the Attract Mode sound level only when you turn on Attract Mode. The Attract Mode sound level is independent of game audio levels. The Attract Volume range is 1 to 100%. The factory default is 50%.

MINIMUM VOLUME sets the quietest sound level during game play. The range is 1 to 100%. The factory default is 20%.

To exit the Volume Adjustment Menu, highlight RETURN TO PREVIOUS MENU. Then press TEST MODE.

Diagnostic, Audit & Adjustment Menu System 3-31

Page 52

Operator Menu (continued) Adjustments Menu (continued) Force Feedback Adjustment Menu

FORCE FEEDBACK ADJUSTMENT

Select FORCE FEEDBACK ADJUSTMENT MENU at the Adjustments Menu. The Force Feedback Adjustment Menu allows you to alter the intensity of steering wheel feedback.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

MIDWAY

INTENSITY — |

>» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

FORCE FEEDBACK ADJUSTMENT MENU

THE INTENSITY ADJUSTMENT ranges from 0% (minimum) to 100% (maximum). The factory default setting is 60%. If players have superior upper body strength, apply greater force. Younger players may be more comfortable with smaller force settings.

THE FORCE FEEDBACK CENTER TEST checks operation of steering wheel motor drive circuits. Select this option and move the steering wheel to any position. As soon as you release the wheel, it must automatically return to its center position. If it doesn’t, then the vehicle won't respond properly.

Diagnostic, Audit & Adjustment Menu System 3-32

Page 53

Operator Menu (continued) Adjustments Menu (continued) Calibrate Steering, Gas and Brake Menu

CALIBRATE STEERING, GAS AND BRAKE

Select CALIBRATE STEERING, GAS AND BRAKE at the Adjustments Menu. (You can also access this menu from the Operator Menu.) This option allows you to set steering and throttle mechanisms for optimum control during game play. Poorly calibrated player controls can reduce profits.

NOTICE: Before calibrating player control switches, make needed repairs to the game. If you plan to move the game, move it before calibrating player control switches.

To set up each calibration procedure, follow screen directions. Press TEST MODE to begin the procedure.

MIDWAY

= PRESS TEST TO BEGIN CALIBRATION OR CREDIT TO EXIT.

MoV E NG WHEEL TO CENTER > KE THEN F T GAS aA

MOVE ING, VD AKE FULL RANGE PF ST

STEERING, GAS AND BRAKE CALIBRATION SCREEN

The steering wheel, brake and gas pedal couple to potentiometers. These potentiometers output DC voltages between zero and five volts. Game electronics digitize this analog output into an eight-bit (256value), numeric stream.

Watch the numbers on the calibration screen. These numbers vary to indicate a control's position within that control’s range of motion. For instance, steering straight ahead produces a number halfway between the left and right steering limits. To accurately simulate steering, numbers must change sequentially.

Diagnostic, Audit & Adjustment Menu System 3-33

Page 54

Operator Menu (continued) Adjustments Menu (continued) Set Time and Date Menu

SET THE TIME AND DATE

Select SET TIME AND DATE at the Adjustments Menu. The Set Time and Date Menu provides the current date and time for the game. This screen also allows clock adjustments for time zone changes and seasonal time changes.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

MIDWAY

THOUR8 pm

T INUTES @1

TSECONDS46
TMONTHJun
TDATE3
SETYEAR1999

>» RETURN TO PREVIOUS MENU

8:61:46 pm, Thu, Jun 3,

Press TEST to return to previous menu

SET TIME AND DATE MENU

The clock assists in providing accurate game statistics. It doesn’t affect game operation. When the circuit board isn’t receiving external power, the clock runs until the battery fails.

Diagnostic, Audit & Adjustment Menu System 3-34

Page 55

Operator Menu (continued) Utilities Menu

UTILITIES MENU

Select UTILITIES MENU at the Operator Menu. The Game Utilities Menu permits you to clear game credits, player statistics, and game audits. Here, you restore game settings to factory defaults or save audit data. A confirmation screen appears before you finalize changes.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

MIDWAY

CLEAR CREDITS

RESET OPERATOR SETTINGS

RESET HIGH SCORES AND SPLIT TIMES

RESET AUDIT STATS

FULL FACTORY RESTORE

SAVE AUDITS TO FLOPPY DISK

RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

UTILITIES MENU

CLEAR CREDITS zeros all credit variables.

RESET OPERATOR SETTINGS returns Adjustments Menu variables to factory default values.

RESET HIGH SCORES AND SPLIT TIMES overwrites the player high scores with factory default data.

RESET AUDIT STATS zeros track and truck audit values.

FULL FACTORY RESTORE resets all variables above to factory default values. A confirmation screen appears before you finalize changes.

Diagnostic, Audit & Adjustment Menu System 3-35

Page 56

SAVE AUDITS TO FLOPPY DISK allows you to copy game data to a disk. Comparing audit data over time demonstrates the effect of game variable changes on profits. Use a formatted, 1.44MB high-density diskette. The floppy drive is in the CPU cabinet.

NOTICE: Be careful when clearing audit information. Once you clear data, you can’t restore it. Use the Save Audits to Floppy Disk option to save data for analysis. To clear audit registers, use the Reset or Full Factory Restore functions.

MIDWAY

TOR SETTINGS

ORES AND

T AUDIT TATS

>» FULL FACTORY RE ARE YOU _ SURE SAVE AUDITS TO TO RESET E' THE FACTORY D RETURN TO PREVI

VOL-— and YOL+ to select; to accept; CREDIT to cancel

A CONFIRMATION SCREEN APPEARS BEFORE YOU FINALIZE CHANGES

Diagnostic, Audit & Adjustment Menu System 3-36

Page 57

Operator Menu (continued) Volume Adjustment Menu

VOLUME ADJUSTMENT MENU

Select VOLUME ADJUSTMENT at the Operator Menu. (You can also access this menu from the Adjustments Menu.) The Volume Adjustment Menu allows you to adjust relative sound loudness levels.

Highlight an option with the middle two diagnostic buttons inside the coin door. Press TEST MODE to enter Change Mode. Use the diagnostic switches to change the variable. Then press TEST MODE to save changes and exit the variable.

MIDWAY

MASTERVOLUME—|40
ATTRACT VOLUMEi]|40
MINIMUM VOLUME—_20

SAMPLE MUSIC 1

>» RETURN TO PREVIOUS MENU

Press TEST to return to previous menu

VOLUME ADJUSTMENT MENU

NOTICE: The Master Volume setting affects all other volume adjustments. You can still alter Attract sounds in relation to normal game sound. For example, suppose that you set Attract Mode volume to 50%. Then Attract Mode sounds are half as loud as normal game sounds.

NOTICE: Check the Master Volume setting before testing. Increase Master Volume to fully test speakers. Restore Master Volume to its previous level before returning to Game-Over Mode.

MASTER VOLUME sets the overall volume level during game play. This value simultaneously affects all other sound settings. The range is 1 to 100%. The factory default is 60%.

Diagnostic, Audit & Adjustment Menu System 3-37

Page 58

ATTRACT VOLUME adjusts the Attract Mode sound level only when you turn on Attract Mode. The Attract Mode sound level is independent of game audio levels. The Attract Volume range is 1 to 100%. The factory default is 50%.

MINIMUM VOLUME sets the quietest sound level during game play. The range is 1 to 100%. The factory default is 20%.

To exit the Volume Adjustment Menu, highlight RETURN TO PREVIOUS MENU. Then press TEST MODE.

Diagnostic, Audit & Adjustment Menu System 3-38

Page 59

Operator Menu (continued) Calibrate Steering, Gas and Brake Menu

CALIBRATE STEERING, GAS AND BRAKE

Select CALIBRATE STEERING, GAS AND BRAKE at the Operator Menu. (You can also access this menu from the Adjustments Menu.) This option allows you to set steering and throttle mechanisms for optimum control during game play. Poorly calibrated player controls can reduce profits.

/ NOTICE: Before calibrating player control switches, make needed repairs to the game. If eB you plan to move the game, move it before calibrating player control switches.

To set up each calibration procedure, follow screen directions. Press TEST MODE to begin the procedure.

MIDWAY

= PRESS TEST TO BEGIN CALIBRATION OR CREDIT TO EXIT.

WHEEL

STEERING, GAS AND BRAKE CALIBRATION SCREEN

The steering wheel, brake and gas pedal couple to potentiometers. These potentiometers output DC voltages between zero and five volts. Game electronics digitize this analog output into an eight-bit (256value), numeric stream.

Watch the numbers on the calibration screen. These numbers vary to indicate a control’s position within that control’s range of motion. For instance, steering straight ahead produces a number halfway between the left and right steering limits. To accurately simulate steering, numbers must change sequentially.

Diagnostic, Audit & Adjustment Menu System 3-39

Page 60

NOTES

Diagnostic, Audit & Adjustment Menu System 3-40

Page 61

Q hg by Q DB g

a S S S iS hy

WIRING & CIRCUIT INFORMATION

WARNING: Failure to reconnect ground wires or replace metal shields may result in radio frequency interference.

NOTICE: The term VGM refers to the video game machine.

Wiring & Circuit Information 41

Page 62

Harness Connector Prefixes

Connector Location Example Arcade Computer 1P1

MagicBus™ Interface Board 3P1 Fluorescent Lamp 4P1 Power Supply 5P1 Video Monitor 6P1 Wheel Driver Board 7P1 Coin Door Area 8P1 BB12 Audio Board 9P1 LED Interconnect Board 10P1 Cabinet 11P1 Optional Overhead Marquee 12P1 Dashboard 13P1 Gas Pedal & Brake 14P1 Upper Speakers 15P1 Seat Speaker 16P1 Dash LED Board 17P1

NOTICE: Look for the connector prefix on wiring diagrams. The prefix shows you where you'll find the connector.

Wiring & Circuit Information 4-2

Page 63

Wiring & Circuit Information 4-3 To IEC Power Cord

OFFROAD THUNDER 27”

ntry Specific Z

Power Cord — 50-1 4699—XX ( foxorexe

Po

Country Specific Fuse Mounting Plate

in Men. Horn

ve

Qansne Tansromer 6P2

ICMP _SYNC_YEL.

INE

FILTER

NC VIDEO |\vip GND YEL “BLK] ONITOR| vid BLU Yeu Bul 2 GRN_YEL_GRN RED YEL_RED| id smo ‘ornection on Mein Harness

oker Oo

Power Mountinc

OPTIONAL

DOLLAR BILL LIDATER,

Inlet Plate BLK WAL CTS TO N.HARNE ALSO

GRN_YEL

NOTE 1: All Earth res (green-y Connect to pem stud on Power inlet fo Seat Speaker Connection on |20 40 kK 5

rae GRNYEL—orth Ground x4 BS YEL Earth Ground 4 To Seat Speaker Cable In Seat Assembly (NOT ALL WIRES USED)

KEY ranstorms To a To Monitor Power Wiring Diagram

Page 64
Scan of page 64

This page is a drawing, shown as the original scan.

Page 65

Player Panel Wiring Diagram

DASH ASSEMBLY

i . 1 vio BLK 3 [NC 3 x ORS BLe Sows ons

e 7 “>)CHOPPER CAM : SLAM CaM a CRASH CAM hol CHOPPER CAM 1 Lo Ki Ground RED BRN

2 [ors Btu 25K. 4 BLK _GRY or VIO BLU in = FPO BLU sey, WEDGE Base | KEY KO) Nitro” 473’ sue. ‘ ORG BLK —/ Lamp BLACK Nitro BOOST f WHT VIO, _] Button

HIET a HIET GRN_RED_ SHIFT Je

  • [4 KEY 3 BLK GND 9 | BLK GND.

Oo RED BLK +5vDC oe 3p) 7 PRE +5vDC_ 17 xt 13R2 pf RED BLK +5VDC |o)— 3 | KEY 3k A a [BLK on (yj> 5| BLK cND_|5

al 26 PIN RIBBON CABLE 0 STRIPE INDICE ATES PIN 1

Wiring & Circuit Information 14P1

CONNECTS TO

SEA CABLE, H GAS/BRAKE PEDA\I ASSEMBLY

20-10135

1 [RED BRN Vv 2 LORG VIO 3 ORG GRY ale 4 |KEY 5 |BLK_GRY GND

UPPER SPEAKER CABLE . H-23638 Speake: 25 W

Full Range

BRN VIO FR Right eaker

EAK'

RED vio f SB 4a econ 25W 8 tN 5 NE 8 Sromw vet f*

co] com Sok] VETER

4-5

Page 66

Computer Motherboard Assembly 20-10554

MOTHERBOARD CONNECTOR AND JUMPER STATUS

(NOTES FOR TABLE ON FOLLOWING PAGE)

NOTICE: The term VGM refers to the video game machine.

NOTES: SLPNOTARWONMS VGM doesn’t require jumper or telephone connection. VGM doesn't require jumper. VGM uses proprietary network for game linking. VGM doesn't require connections. VGM has no ATAPI devices (CD ROMs). VGM doesn't require jumper. Tamper-detection security feature isn’t installed. Connect processor module fan to this jack. Computer may become unreliable if processor overheats. Connect processor module to this jack. 242-pin socket accepts single microprocessor modules. VGM doesn't require connections. Case cooling fans connect directly to power supply. VGM doesn’t require connections. VGM doesn’t use SCSI devices (Hard Drives). Connect reset cable from Filter Board to this jack. VGM doesn’t use front-panel devices. . Jumper must be set over pins 1 & 2 for this VGM. VGM won't run with incorrect or missing jumper.

Replacement Motherboards may not include this jumper. Refer to Parts to order extra shunt jumpers.

Wiring & Circuit Information 4-6

Page 67

Motherboard Connector and Jumper Status Table

Designation Location Function Meaning Setting Default

J1A1Lower RightWakeNot Used In ThisOpen:
Near BoardOnVGM (No1&2
(Note 1)Expansion SlotRingTelephone)
J1E1Lower CenterWakeNot Used In ThisOpen
Near BoardOnVGM (No
(Note 2)Expansion SlotLANPC LAN)
J1F2Lower CenterCD AudioNot Used In ThisOpen
Near BoardInputVGM (No
(Note 3)Expansion SlotCircuitCD Player)
J2F1Lower CenterCD DataNot Used In ThisOpen
Near BoardInputVGM (No
(Note 3)Expansion SlotCircuitCD Player)
J2F2Lower CenterTelephonyNot Used In ThisOpen
Near BoardInputVGM (No
(Note 1)Expansion SlotCircuitTelephone)
J2F3Lower CenterAuxiliaryNot Used In ThisOpen
Near BoardInputVGM (No
(Note 3)Expansion SlotCircuitAux Devices)
J3F1Middle CenterChassisNot Used In ThisOpen
Near CPUIntrusionVGM (No1&2
(Note 4)And FanCircuitIntrusion)
J3F2Middle CenterProcessorTwo Speed FanOpen
Near CPUFanFor Processor1,2,&3
(Note 5)And FanCircuitCooling
J4J1Center LeftSystemSystemOpen

Module With Micro- Micro- Filled

(Note 6)Fan AssemblyProcessorProcessor
J4M1Center LeftProcessorControlled FanOpen
Near CPUFanFor Processor1,2,&3
(Note 7)ModuleCircuitCooling
J7M1Upper LeftCaseControlled FanOpen
Near Power &FanFor Hard Disk1,2,&3
(Note 7)Floppy JacksCircuitDrive Cooling
J8J1Upper LeftSCSINot Used In ThisOpen
Between HardDriveVGM (No1&2
(Note 8)& Floppy JacksIndicatorSCSI Drives)
J8FRUpper CenterFrontOnly ResetOpen
Near Hard DiskPanelPins Are Used1&2
(Note 9)Drive JacksDevicesIn This VGM
J8A1Upper RightConfigur-Starts SystemOpen
Near BatteryationSetup Routine1&2
(Note 10)And SpeakerSelector Operation2&3

Wiring & Circuit Information 4-7

Page 68

Network Interface Board Assembly 20-10550

Network Interface LED Indicator Table

Designation Location Function Color State Meaning

LED 1Left CenterLink VerifyGreenOffNot In Use
(LNK)Under JackIndicator(No Game Link)

On Normal Operation

Blinking Link Fault

(Note 1)

LED 2Right CenterActivityGreenOffNot In Use
(ACT)Under JackIndicator(No Data)

On Receiving Data (Note 2)

Blinking Normal

Operation

Notes:

  • Intermittent cable or hub problems may cause blinking. Blinking must be continuous during linked operation.
  • Blinks during data packet exchange. Blinking may appear continuous during heavy network activity.

Wiring & Circuit Information 4-8

Page 69

Video Graphics Board Assembly 20-10551

== 0ULL

Video Graphics Connector And Jumper Table

Designation Location Function Meaning Setting Default Ji Left Center Video Graphic Open

(DB-15 onSignalInformation1-15
(Note 1)Bracket)OutputTo Interface
J2-J7None-_Not UsedOpen

(Note 2)

JP2NoneNot UsedOpen

(Note 2)

Notes:

  • Connects to Interface Board through shielded cable. Doesn’t connect directly to monitor.
  • Manufacturer option connectors and jumpers. Not required for this VGM.

Wiring & Circuit Information 4-9

Page 70

BB12 Audio Amplifier Board Assembly 04-12529.1

BB12 Audio Amplifier LED Indicator Table

Designation Location Function Color State Meaning

LED 1Upper CenterFaultRedOffNormal
(CR1)Near C3IndicatorOperation

On Locked Up (Note 1)

Blinking Overload

(Note 2)

LED 2Lower CenterFaultRedOffNormal
(CR2)Near U2 & U6IndicatorOperation

On Locked Up (Note 1)

(Note 2)

NOTES:

  • Active output protection circuit. Attempt to reset circuit by clearing fault and removing power.
  • Intermittent audio overload or overheating may cause blinking. LED should flash only during startup.

Wiring & Circuit Information 4-10

Page 71

worth High Pass fiiters

butter

250 He BB12 Audio Amplifier Board Schematic, 1/4

re led order

BCA JACK

Fe is epaut

8145 7 oT 2.5 t+ , Hoe

i

ay > 8 Liga TT a & L__1j) STUFF CZ@ WITH & *O* OKN RESISTOR 7! * ]

-—ii_—__+* 2 Pa SW sie a =| “ . oS aa a LW Pas L_yy—$# z

ae oe x ? =a ra

ei: Fd

Bias

Wiring & Circuit Information 4-11

Page 72

BB12 Audio Amplifier Board Schematic, 2/4

Ase asaKiy ax

180K 43%

co a

tT

= * :

. :

7 * peer cones

* °

Wiring & Circuit Information 4-12

Page 73

BB12 Audio Amplifier Board Schematic, 3/4

Wiring & Circuit Information 413

Page 74

BB12 Audio Amplifier Board Schematic, 4/4

GH

Stereo and Subwoofer Amp

Wiring & Circuit Information 4-14

Page 75

MagicBus™ Interface Board Assembly 04-12697.3

Designation Location Function Positions Meaning

S1-7 Right Center Near USB / UART 2 UART Mode D19 - D26 Mode Selector USB Mode

Right Center Near | Host Watchdog Watchdog

D19 - D26 Reset Enabled

Watchdog Disabled

Notes:

  • Bank 1, Switch 8 should be off for Offroad Thunder. See the table above.
  • Bank 1, Switch 7 should be off for Offroad Thunder. This switch selects USB or UART Mode. This video game machine doesn’t support USB Mode.
  • Bank 1, switches 1 through 6 have no assigned function. Leave these switches off.
  • Bank 2, switch 1 through 8 have no assigned function. Leave these switches off.

Wiring & Circuit Information 4-15

Page 76

MagicBus™ Board LED Indicator Table, 1/2

LED #LocationFunctionColorStateMeaning
LED 28Left Center, NearOffNo +12V

Fuse F2 &

+12V PowerConnector JP12IndicatorRedOn+12V Present

for Output

Lamps Blinking Intermittent +12V

LED 27OffNo +5V
+5V Power forRight, Near DIPIndicatorRedOn+5V Present

Analog Fuse F1 Inputs Blinking Intermittent +5V LED 10 Off Not In Use

Communi-Right Center, NearIndicatorRedOnCommunication
cationDIP Switch S1Error

Blinking Normal Operation

LED 9 Off Not In Use

EEPROMRight Center, NearIndicatorRedOnEEPROM not

DIP Switch S1 responding

LED8 Off Not In Use

SecurityRight Center, NearIndicatorRedOnSecurity error

DIP Switch S1

LED 7OffNot In Use
MagicBusRight Center, NearIndicatorRedOnMagicBus Reset

Reset DIP Switch S1

LED 6OffFaulty MagicBus

Board

MagicBusRight Center, NearIndicatorGreenOnFaulty MagicBus
ProgramDIP Switch S1Board
RunningBlinkingNormal Operation
LED5OffNot In Use
UART/USB | Right Center, NearIndicatorGreenOnFaulty MagicBus
ModeDIP Switch S1Board

Blinking With 4 & 3: UART; Individually: USB

LED 4OffNot In Use
UART/ USB | Right Center, NearIndicatorGreenOnFaulty MagicBus
ModeDIP Switch S1Board

Blinking With 5 & 3: UART; Individually: USB

Wiring & Circuit Information 4-16

Page 77

MagicBus™ Board LED Indicator Table, 2/2

LED 3 Not In Use

UART/USB | Right Center, NearIndicatorFaulty MagicBus

Mode DIP Switch S1 Board Blinking With 5 & 4: UART; Individually: USB

LED 1 Off No Power

Power toCenter, NearIndicatorOnPower Present

MagicBus™ Fuse F2

Board Blinking Intermittent Power

MagicBus™ Interface Connector & Jumper Table

Jumper Location Function Meaning Setting Default

JP 1Upper RightBlueHigh ImpedanceOpenLJ
BetweenVideoLow Impedance1&2
(Note 1)JP4 and JP2ImpedanceHigh Impedance2&3
JP2Upper RightGreenHigh ImpedanceOpen
BetweenVideoLow Impedance1&2
JP1 & JP3ImpedanceHigh Impedance2&3
JP3Upper RightRedHigh ImpedanceOpen
BetweenVideoLow Impedance1&2
(Note 3)JP2 & JP5ImpedanceHigh Impedance2&3
JP4Upper RightVideoPositive SyncOpen
NearSyncNegative Sync1&2
(Note 3)JP1 & JP2PolarityPositive Sync2&3

Wiring & Circuit Information 4-17

Page 78

Wheel Driver Board Assembly 04-12770.1

Wheel Driver Board Led Indicator Table

Designation Location Function Color State Meaning

LED 1 Right Center, Near Indicator Red Off Not In Use C5 & P2 On Normal Operation

Blinking Power Fault

(Note 1)

Notes:

  • LED 1 monitors regulated power supply voltage source. Must be on continuously. Flash or blinking indicates intermittent connection, power problem, circuit fault, etc.

Wiring & Circuit Information 4-18

Page 79

Wheel Driver Board Schematic, 1/8

pete

Hast conne

ae

aad ves

2zfe

a — a + a)

44an

2 o $2

*4ec

_ = = - aa 23

oe gn ten os ° 63 aad co

Wiring & Circuit Information an

Page 80

Wheel Driver Board Schematic, 2/8

xooo

Wiring & Circuit Information 4-20 wore VV rr >:

4 are yr 5

aw He Ecies »

o'r ¢ a

4 Tar | wh ve bene epee »:

8/8 ewes ° Changed C31 fram 100pf to Z200pF

5/19/39

Page 81

Wheel Driver Board Schematic, 3/8

2Ne427 mi oy 2ey “Ty

THRU HOLE SOCKET

La

Wiring & Circuit Information 4-21

Page 82

Wheel Driver Board Schematic, 4/8 ease of using previgus layout

Rappea to GND for

DGND shaute andy cannect to GND at one paint

OGND has been

The Nete on

LAYOUT NOTE:

ChOSEW=THIS CHOSENe THIS

Wiring & Circuit Information 4-22

Page 83

Wheel Driver Board Schematic, 5/8

PWR_AMP atu,

DACOUTS

Wiring & Circuit Information 4-23

Page 84

Wheel Driver Board Schematic, 6/8

Lamp Driver Outputs

uinzose

Wiring & Circuit Information 4-24

Page 85

Wheel Driver Board Schematic, 7/8 [ a

Page 86

Wheel Driver Board Schematic, 8/8

FR Auxalary peripheral connectar

anaes

Wiring & Circuit Information 4-26

Page 87

SERVICING

NOTICE: The term VGM refers to the video game machine.

NOTICE: Avoid damage to electronics! Turn off VGM power before servicing circuit boards or any electronic assembly. Never “hot plug” circuit boards.

CAUTION: Static electricity builds up on your body. This static can damage or destroy sensitive circuits. Before touching or handling electronics, discharge static electricity by touching the power supply chassis.

Servicing 5-1

Page 88

DISASSEMBLY & REASSEMBLY This chapter includes summarized procedures for disassembling and reassembling VGM components. Only qualified service personnel should repair VGM equipment. The following product guidelines apply to all video game operators and service personnel. Notes, cautions and warnings appear throughout this manual where they apply. Study the Safety pages before beginning service.

« Arcade Computer

Switch off power to the VGM.

Open and remove the rear door. The Arcade Computer is behind fs << this door. To expose Arcade

Computer circuitry, loosen four metal thumbscrews. Don’t remove

the screws. These screws reside

at the top and bottom corners of

the case. Slide off the back of the

computer.

« Audio Amplifier Board BB12 Switch off power to the VGM. Unlock and open the rear door. The BB12 Audio Amplifier Board mounts to the wooden shelf behind the steering motor. Note the orientation of the connector and other cables. Extract the harnesses from the board connectors. Remove mounting screws from the Audio Board. Lift the board out of the cabinet. Handle the board by a heatsink. If you aren't reinstalling the board, store it in an anti-static bag and protective container.

  • Battery
CAUTION: If you install the battery incorrectly, it may explode! Avoid direct shorts across the terminals or from terminals to ground. These batteries are designed for very long life. Don’t attempt to recharge these batteries!
CAUTION: Avoid an explosion! Replacement batteries must match the originals in size, voltage rating, and composition. Manufacturer recommended equivalent types are acceptable. Store batteries in a safe place until you’ve completed repairs. Dispose of used batteries according to manufacturer instructions.

A battery on the CPU Board retains data in memory during power disruptions. This battery is a 3-volt, lithium button cell. Switch off power to the VGM. Unlock and remove the rear door. Remove the back of the Arcade Computer. The battery resides toward the edge of the motherboard, near the daughter

Servicing 5-2

Page 89

board sockets. Carefully pry up the battery retaining lever. Then grasp the battery edges and remove the device. Set the battery aside.

Note the “+” marking on one side of the replacement battery. When you install a battery, this “+” marking must face the battery retaining lever. After replacing the battery, set the system clock to the correct date and time. Also enter the Menu System and check or update system adjustments as necessary.

Coin Counter Meter replacement requires vault removal. Switch off power to the VGM. Unlock and open the coin door and cashbox door. Find the meter behind the bottom of the cashbox door. Remove the cashbox.

Remove two mounting screws at the bottom (front) of the vault assembly. Reach through the cash door. You'll find two mounting screws at the back of the vault. Remove these. Access the four remaining vault screws from the inside-back of the cabinet. Remove these four screws. Slide the vault out of the cabinet.

Locate the meter wires under the vault. Disconnect wiring at the connector. Remove two mounting screws from the front of the meter. Remove the meter. Assure that the replacement meter has a diode across its terminals. This diode protects driver circuits from the meter’s inductive kick. Install the new meter. Log the new meter count.

Coin Mechanism Switch off power to the VGM. Unlock the coin door and swing it open. To clean or replace a coin mechanism, unlatch and remove it. After reinstallation, assure that the mechanism seats fully in its bracket. Close and lock the release latch. Then close the door. Enter the Menu System to change the coin mechanism setup. Test known good and bad coins to verify operation.

CPU Board

The CPU Board is part of the Arcade Computer. Switch off power to the VGM. Open and remove the rear door. The Arcade Computer is behind this door. Find the four metal thumbscrews at the top and bottom corners of the computer case. To expose the CPU Board, loosen, but don't remove these screws. Slide off the back of the computer. Unscrew and remove the circuit board retention bars. Disconnect external cables to the Video Board, Network Board and Power Filter Board. Remove the Video Board, Network Board and Power Filter Board. Disconnect the floppy disk power and data cables at the disk drive. Remove the floppy drive-mounting bracket. Lift the bracket and floppy drive out of the cabinet. Set these aside for reassembly.

Servicing 5-3

Page 90

Remove the CPU Board power cables at the CPU Board. Remove the circuit board retention bars. Disconnect the hard drive power and data cables at the disk drive. Remove CPU Board mounting screws. Lift the circuit board out of the cabinet. Use anti-static packaging from new parts to store boards that you won't reinstall.

Dashboard and Steering Mechanism

Switch off power to the VGM. Unlock and remove the rear door. From inside the cabinet, disconnect the dash cables. Sit in the driver's seat and support the steering wheel. Remove the top two dashboard mounting screws. Remove the dash bracket. Slide the viewing glass upward. Lift the glass out of the cabinet. Remove the bottom two dash screws. Remove the dashboard and set it on your workbench.

Inspect the motor, pulleys, and belt. If the belt is broken or shows signs of wear, replace it. Locate the two nuts on each side of the motor mounting bracket. Loosen all four bracket nuts. Rotate the tension adjustment bolt as necessary. Tighten this bolt until the belt is taut. Then restore correct tension by loosening the bolt one full turn. Tighten the motor bracket nuts.

DIMMs (Dual In-Line Memory Modules)

DIMM circuits contain the computer read-write memory for this VGM. Switch off power to the VGM. Remove the cabinet rear door. Remove the back of the Arcade Computer. Unplug the ribbon cable from the floppy drive. Leave the other end of the cable attached to the CPU Board. Unscrew and remove the circuit board retention bars. Remove the floppy drive mounting bracket. Remove the floppy drive.

Note DIMM positions. Press out on the locking retainer on each side of the DIMM. The DIMM should partially or completely pop out of its socket. Lift the DIMM from its socket. Handle the DIMM only by its edges.

To reinstall memory circuits, orient the DIMM over its socket. Make sure that you've positioned the keying holes and notch properly. Push the DIMM board into its socket. The board should snap into place, engaging a locking retainer at each socket end. Be sure that the retainers mate tightly with DIMM board notches. Don't attempt to force a DIMM into its socket.

Servicing 5-4

Page 91

Dollar Bill Validator (Use MARS AE2451-U3E, UL-recognized currency changer) You can install dollar bill validators in VGMs manufactured with the additional wiring connector. As this manual goes to press, this VGM only supports the Mars® model AE2451-U3E validator.

Switch off power to the VGM and unplug the AC line cord. Unlock the coin door and swing it open. Read the coin door label for additional information.

Remove nuts, spacers, and the cover plate from the door. Before mounting the validator, change switch settings or make adjustments. (Set the validator for 1 pulse per dollar. Also adjust the pulse width setting. The validator must generate pulses with these timing parameters: 50mS on and 50mS off.) If the manufacturer supplied an adapter plate, place it over the door cutout. Install spacers on threaded studs. Then align the validator mounting holes with the studs. Seat the validator in the door opening. Install the nuts and tighten them.

Attach the ground wire (green with yellow stripe) lug to the door ground stud. The stud is beside the hinge. Mate the wiring harnesses and press them together to fully seat connectors. Route wires away from the door edges and hinge. To remove a validator for service or replacement, reverse these steps.

Plug in the line cord and turn on the VGM. From the Menu System, change the mechanism setup and pricing. Then test known good and bad bills to verify proper operation. Close and lock the coin door.

Fans The Arcade Computer incorporates several fans. Two fans reside at the bottom of the Arcade Computer enclosure. The power supply includes one fan. Inside the microprocessor cartridge is another small fan.

Switch off power to the VGM. Remove the cabinet rear door. Remove the back of the Arcade Computer.

FANS AT THE BOTTOM OF THE ENCLOSURE. Disconnect the fan’s power harness. Remove the fan mounting screws. Note the fan orientation. Each fan has an arrow molded into its plastic case to indicate airflow direction. Slide the fan out of its mounting bracket. Be certain to reinstall the fan in the proper direction to assure airflow over circuitry.

POWER SUPPLY FAN. The power supply contains no user-serviceable parts. Never open the power supply.

Servicing 5-5

Page 92

MICROPROCESSOR FAN. Disconnect the DC power cable from the floppy drive. Unplug the ribbon cable from the floppy drive. Leave the other end of the cable attached to the CPU Board. Unscrew and remove the circuit board retention bars. Remove the drive bracket mounting hardware. Remove the bracket and drive. Disconnect the fan’s power

harness.Removethe

microprocessor cartridge. Squeeze the plastic end tabs on the fan side of the cartridge. While squeezing, carefully pry the fan assembly away from the heatsink. If the fan is bad, replace the entire fan assembly with a

newone.Reassemblethe

cartridge and insert it into the computer. Then reconnect fan power.

Floppy Disk Drive Switch off power to the VGM. Unlock and remove the rear door. Remove the back of the Arcade Computer. Disconnect the DC power cable from the floppy drive. Unplug the ribbon cable from the floppy drive. Leave the other end of the cable attached to the CPU Board. Unscrew and remove the circuit board retention bars. Remove the drive bracket mounting hardware. Remove the bracket. Remove the drive mounting screws. Lift the drive off the mounting bracket. Save the mounting screws for reuse in future floppy drive installations. When returning a floppy drive to your distributor, pack it in an anti-static bag.

REINSTALLATION. Mount the floppy drive in its bracket. Install the drive mounting screws. Reinstall the bracket and drive in the Arcade Computer enclosure. Connect the drive’s ribbon and power cables.

Gas and Brake Pedals

Switch off power to the VGM. Adjust the seat to the maximum rear position. Remove four outer mounting screws from the front edges of the pedal plate. Gently pull the pedal mechanism toward the seat until the mechanism clears the

cabinet opening. Disconnect the pedal

cablefromthewiringharness.

Disconnect the green / yellow safety ground wire. Lift the pedal mechanism up and away from the cabinet.

Servicing 5-6

Page 93

Gear Shift Switch off power to the VGM. Unlock and remove the rear door. Disconnect the two cables from the back of the shifter. At the front of the shifter, remove shift plate mounting screws. Lift the shifter up and out of the player panel.

Hard Disk Drive

CAUTION: Hard disk drives are very fragile! Handle them with care. Keep disk drives away from magnets, heat and vibration. Don’t move a VGM with the power on.

IN CAUTION: Don’t stack or drop hard disk drives. Use an anti-static bag and an

approved shipping container to return the drive to your distributor.

CAUTION: Static electricity builds up on your body. This static can damage or destroy sensitive circuits. Before touching or handling electronics, discharge static electricity by touching the power supply chassis.

Switch off power to the VGM. Unlock and remove the rear door. Remove the back of the Arcade Computer. Disconnect the DC power cable from the hard drive. Unplug the ribbon cable from the hard drive. Leave the other end of the cable attached to the CPU Board. Remove the drive mounting screws. (Don’t remove the drive-mounting bracket.) Lift the drive out of the cabinet. Save the mounting screws for reuse in future hard drive installations. When returning a hard drive to your distributor, pack it in an anti-static bag. Box the drive in approved shipping container 08-8068.

REINSTALLATION. Before mounting the hard drive in its bracket, install the drive mounting screws. To avoid damage during installation, mount the hard drive in the brackets before connecting cables.

After a driver plays one game, the new drive copies data from other linked VGMs. Important! The data won't copy if players are actively driving. Files transfer only when all VGMs return to Attract Mode.

MagicBus™ Interface Board Switch off power to the VGM. Unlock and open the rear door. Extract the harnesses from the board connectors. The MagicBus Board mounts to the left cabinet wall. Remove mounting screws from the board. Lift the board out of the cabinet. During reinstallation, tighten the screws: Start at the board’s center and work toward the outer edge. If you aren’t reinstalling the board, store it in an anti-static bag and protective container.

Marquee Glass and Fluorescent Tube Switch off power to the VGM. Unscrew and remove the marquee glass retainer. Lift off the glass panel and artwork to expose the interior of the light box. The fluorescent lamp requires a quarter turn for removal.

Servicing 5-7

Page 94

Microprocessor This VGM’s microprocessor is in a postcard-size cartridge that also includes cache RAM. The cartridge is inside the Arcade Computer, near the DIMM sockets. Switch off power to the VGM. Remove the cabinet rear door. Remove the back of the Arcade Computer. Unplug the ribbon cable from the floppy drive. Leave the other end of the cable attached to the CPU Board. Unscrew and remove the circuit board retention bars. Remove the floppy drive mounting bracket. Remove the floppy drive. Disconnect the microprocessor fan power harness. Spread the locking retainers on each side of the microprocessor cartridge. Pull the cartridge out of its socket. Take care not to touch the copper traces on the socket.

To reinstall a microprocessor cartridge, orient the cartridge over its socket. Make sure that you've positioned the keying notch properly. Push the microprocessor cartridge into its socket, so that the cartridge snaps into place under the locking retainer on each side of the socket. Be sure that the retainers mate tightly with cartridge notches. Don’t attempt to force a cartridge into its socket. Reconnect the microprocessor fan harness.

Monitor

CAUTION: The video monitor is heavy, with most of the weight toward the front of the assembly. Support the monitor as you remove it from the cabinet.
WARNING: The monitor doesn’t require isolation from AC line voltage during normal VGM operation. When operating the monitor outside the cabinet, use an isolation transformer. Connect the transformer between the monitor and line.

Switch off power to the VGM. Unlock and remove the rear door. From inside the cabinet, disconnect the dash cables. Remove the top two dashboard mounting screws. Remove the dash bracket. Slide the viewing glass upward. Lift the glass out of the cabinet. Disconnect cables from the speedometer and tachometer. Remove the dashboard. Remove the monitor bezel. Disconnect the monitor from the wiring harness, remote adjustment board, and ground wires. Remove the fasteners that secure the monitor frame to its mounting panel. Carefully pull the monitor from the cabinet. Set the monitor in a safe place. Remove the remote adjustment board from the cabinet and reconnect it to the monitor before servicing or replacement. Clean the face of the CRT before reinstalling the monitor bezel.

The monitor is a medium-resolution type with a 25-kHz horizontal scan rate. Other monitors may look as if you can use them for replacements. Yet the screens of different monitor types curve differently. Use only Midway approved replacement parts.

Network Interface Board Switch off power to the VGM. Unlock and open the rear door. Remove the back of the Arcade Computer. Note the orientation of the cables. Loosen the header-mounting screw. Disconnect the network cables from the board header connectors. Remove the circuit board retention bars. Remove the board. As you remove the board, handle it only by its edges. Don’t touch the copper traces! If you aren't reinstalling the board, store it in an anti-static bag and protective container.

Power Filter Board Switch off power to the VGM. Unlock and open the rear door. Remove the back of the Arcade Computer. Loosen the header-mounting screw. Disconnect the cables from the board header connector. Remove the circuit board retention bars. Remove the board. As you remove the board,

Servicing 5-8

Page 95

handle it only by its edges. Don’t touch the copper traces! Use anti-static bags and protective containers to store the board if you won't reinstall it.

Power Supply

CAUTION: Replace the power supply only with a Midway approved power supply. Make no substitutions. Otherwise you will void the UL and CE listings on your video game machine. Non-approved power supplies can pose shock and fire hazards to players and service personnel.

Switch off power to the VGM. Disconnect the line cord. Unlock and remove the rear door. Remove the back of the Arcade Computer. Unplug the IEC AC power cord. Inside the Arcade Computer, disconnect DC power cables. These connect to the hard drive, motherboard and other peripherals. Remove four mounting screws from the outside of the Arcade Computer enclosure. Lift the power supply out of the cabinet. Before reinstalling the power supply, check the line voltage switch setting.

Speakers

This VGM has four speakers. One woofer is ea. ys TAUPER RESISTANT SCREW behind a grille at the back of the driver's seat. Smaller, full range speakers are behind the marquee. A second woofer is inside the main cabinet, accessible from the back. Switch off power to the VGM.

ACCESSING THE SEAT WOOFER. Remove mounting screws and set the speaker grille aside. Don’t use excess force when removing or tightening mounting screws threaded into plastic. Avoid speaker damage by removing the upper mounting screws first. (Replace these top screws last.)

ACCESSING THE CABINET WOOFER. Unlock and remove the rear door. Unscrew the Arcade Computer mounting brackets. Disconnect and remove the Arcade Computer. Unscrew and remove the computer's wooden mounting panel. Remove speaker-mounting screws.

ACCESSING A MARQUEE SPEAKER. Unscrew and remove the marquee retainer. Expose the speakers by removing the marquee glass. Remove speaker-mounting screws.

SPEAKER REMOVAL. Assure proper polarity by marking each speaker wire (“+” or “Gnd”). Remove the speaker from the enclosure and disconnect the wire lugs. Servicing 5-9

Page 96

Video Board Switch off power to the VGM. Unlock and open the rear door. Remove the back of the Arcade Computer. Loosen the header-mounting screw. Disconnect the video cable from the board header connector. Remove the circuit board retention bars. Remove the board. As you remove the board, handle it only by its edges. Don’t touch the copper traces! Use anti-static bags and protective containers to store the board if you won't reinstall it.

26PIN

Wheel Driver Board Switch off power to the VGM. Unlock and open the rear door and the coin door. The Wheel Driver Board mounts to the wooden shelf behind the gearshift. Note the orientation of the connector and the other cables. Extract the harnesses from the board connectors. Leave the other end of the ribbon cable connected to the MagicBus Board. Remove mounting screws from the Wheel Driver Board. Lift the board out of the cabinet. Handle the board by the heatsink. If you aren’t reinstalling the board, store it in an anti-static bag and protective container.

Servicing 5-10

Page 97

PARTS

WARNING: Use of non-Midway parts or circuit modifications may cause serious injury or equipment damage! Use only Midway authorized parts.

For safety and reliability, don't substitute parts or modify Midway products. Substitute parts or modifications may void the game’s EMC directive or FCC type acceptance.

NOTICE: The term VGM refers to the video game machine.

Parts 7A

Page 98

Cabinet Front View

03-8252-5 MARQUEE RETAINER

A-22506 EMBLY 08-7980 / MARQUEE G AMP

__31-3418.2 01-15084 SCREENED MARQUEE SPEAKER GRILL 31-3423.1-2 5675-16273-00 “~~ BEZEL AL RIGHT MONIT EDIUM— ws : RESOLUTION — 08-7853 ~ Bi) CRT GU 31-3423.1-1 a LEFT __03-9932.1 MONITOR BEZEL

~N oN (SEF APP . ™

04-12760-1 oN SECURITY BRA\

04-12760-2 SECURITY BI

Parts 7-2

Page 99

Cabinet Rear View

01-10714 LINKING HEADER CABLE SOVER

03-8326 HANDLE PULL VENT

-—COMPUTER ASSEMBLY

  • (SEE DETAIL DRAWING)

ASTER WHI E DETAIL AWING)

SEAT/PEDESTAL ASSEMBLY (SEE DETAIL ORAWING)

SWIVEL CASTER MAIN CABINE ~ (SEE DETAIL DRAWING)

TRANSFORMER. (SEE APPLICATION CHART)

BR ASSEMBLY

REAR DOOR ASSMBLY —_/ oC (SEE DETAIL DRAWING)

Parts 7-3

Page 100

Parts 7-4 4700-00033-00B y 4701-00005-00 - LOCK HER 4320-01124-16 BOLT 1/4—20x1—-HH 04-10112 UNTING RAIL

CABINET — 4020-01 100-20 1/4-20x1-1/4 BH CS A R RESISTANT.

Cabinet Joining Details

Page 101

Casters and Levelers

VEL MTG. CE 04-10633

3E NUT FLAN 4420-01141-00_

1/2-13 HEXNU \_ 4424-01182-00 08-8023 \_ LEG LEVELER

01-14526

LEVELER PLATE

Parts 7-5

Page 102

Rear Casters

WN FOR REFERENCE)

01-9359 : / WHEEL. BRACKE

02-4404 —_ CASTER SHAFT 4108-01219-11 f8x11/16 PIN-H

va

Parts 7-6

Page 103

Rear Door Assembly A-23238

SK O BK a 4320-01164-20B

PLATE

20-10350 01-11285 OCK

20 FLAN PLATE,

4420-01141-00

CK RETAINER

4108-01219-11 03-7602 : G

H 01-11291

x

NU Parts 7-7

Page 104

Monitor Bezel Components

1 \ | \__03-8252-5 MARQUEE RETAINER 4108-01219-11 PIN= B iff

~ \_ 08-7980 MARQUEE

___4406-01128-00 / 6-32 KEPS NUT

// 5555-15098-00 “SPEAKER 5 1/2

08-7853 CRT GLASS

MONITOR MEDIUM __ | RESOLUTIO!

4506-01106-24B

01-15083.3 03-9932.1 / RETAINER MONITOR BEZEL

Parts 7-8

Page 105

Padlock

CABINET SHOWN FOR R RENCE

NUT 1/4-20 FLANGE GRIP

01-11286 PADLOCK BRKT

01-11287 KEY LOCK BRKT

4320-01164-208 / BOLT 1/4-20x1-1/4 CB

Parts 7-9

Page 106

Coin Door Assembly

(See Coin Door Application Table for Assembly Number)

COIN ENTRY NUT WASHER PLATE \

CAM LOCK ARM—~ ENTRY /REJECT__ BUTTON |

24-8768 LIGHT BULB ~~

N-REJECT FLAP

MECH HOLDER—_

KEY HOOK

A-21069 7 COIN METER

Parts 7-10

Page 107

Pushbutton Assembly

20-9663-XX 20-10129-5

LENS cH LENS AP

_— Leen

a \\ -—tecen

ca ro)

oe uw — Puuncer a a ro)

ro)

afw}c i} co) 4 «)2) — spans aly 3

is)

TTON

is) Ee

a (24-8880 = QQ ae ca Ky 2 | a us ws + oO Ee

Minis

OFFROAD THUNDER SWITCH PUSHBUTTON CHART

Parts 7-11

Page 108

Parts 7-12 20-10494 TRO BUTTON \ __ 20-10595 ~~ SPEED SHIFTER

20-10129-5 START BUTTO 03-9933.2 ____ 03-9910-1 HOOP. CAP 20-1053.1 STEERING WHEEL

20-9663-22 SLAM C 20-9663-23 | CHASE C Dash Assembly A-23113

Page 109

Dash Assembly A-23241 (Exploded)

5014-16301-00 5« POT W/CONNE! 3/8-32 BUSHING

20-10186 TOOTHED. BELT

__ 4420-01141-00 /4~20 FLANGRIP NUT

20-10627 FRING MECHANISM 2 —TOcTHED DRIVE PULLEY

14-8029 MOTOR

I

| 02-5295-34

i s 04-12759.1 ; HEX POST LA ;

eN/eF x 2\.TER?;
\~|A |

\ |) 5795-15667-15 (6) A -01100-

04-12790-4”~‘NER
DASH MOUH-23218a
{BRACKET[~LED POWER cos WY__ 20-10595

j .err SHIFTER

03-9933.2 / MOLDED DASH

31-3419.1 04-12784.1 /~ SPEEDOMETER OVERLAY SUPPORT BRACKET“ / 4006-01100-08B

aWATAMPER RESISTANT

04-12729.3 °/ 20-10183_/ DASH SUPPORT “A SHAFT KEY BRACKE = 4700-00129-008 ~~. FLAT WASHER 203x468x050 XY 4008-01100-08

TAMPE:‘6,i(Hoop)
/i(Je4020-01100-20
3a/—TAMPER RESISTANT
START BUTTON ASS._/7DeneTaUPER RESTA

(SEE DETAIL DRAWN sy / V/-20 V4

//\| 4427-01183-00
4020-01100-20_///1-15080 \JAM NUT, 1/2=20
mtie!4006-01100-16B801-15080 \
TAMPER RESISTANT74098;01100-168view BUTTON\peneetomn
1/4-20 x 1 1/4peseTayyBRACKET\100005008

BUTTON ASSEMBLY \ #4 SPL SEE DETAIL DRAWING) 4008-01 100-08 08-32 x 1/2—~ TAMPER RESISTANT

Parts 7-13

Page 110

Optional Bill Validator

Parts 7-14

Page 111

Cabinet Components

5733-15299-00 ;—FUSE BLOCK x3 AG 1/4 TERM

INTERFACE_ BOARD ASSEMBLY (SEE DETAIL DRAWING) 5827-15144.00 TERMINAL BLOC! S~\ ~~

5795-15667-15, RIBBON CABLE 26°IN 15” a

\ 5795-15667-20 \ RIB3ON CASLE——~ 2% PIN

041065218 RIBBON CABLE —/ W/FERRIDE BEAD

WHEEL DRIVER_SOARD MBLY —/ (SEE DETAIL DRAWING)

'8797-15276-00 AS

(SEE LINE AUDIO. BOARD BLY (SEE DETAIL DRAWING)

/— CANE COMPUTER

'5556-13956-00 FERRITE BEADS 2 PIECE 1-1/4

LINE CORD

iter Y

‘ BRACKET AC PLUG ASSLMLY

\_ravsroawer (SEE APPLICATION CHART)

01-15052 A voumiing BRA at BON ss

4700-00011-00 rt WAS — 172x.437%.032

f 4008-01168-06 _/ MACHINE SCREW ~ 8-32x3/8 PL-HH=S

4008-01168-16 MACHINE SCREW 8-32x1 PL-HH-S ~

A23253 GAME COMPUTER. a OFFROAD THUNDER

Parts 7-15

Page 112

Seat and Pedestal Assembly A-23231

aazoi0m12

Parts 7-16

Page 113

Parts 7-17

PEDESTAL AND CABINET FOR REFERENCE

01-14526 EVELER PLATE \ 04-10633

“#8 x 1 \\_ 4424-01182-00 HEXNUT 1/2-13

Casters and Leg Levelers

08-8023 G LEVELER 20-10360 LEG ELE - eee 4420-01141-00

FLANGE NUT

Page 114

Throttle Assembly 20-10135

ETER

a 5014-12909-00

Parts 7-18

Page 115

Fluorescent Lamp Assembly A-22506

~ Z1SPOL-02

rrbol-02 bbz bi-ro 6089-r2

7-19 Parts

Page 116

Arcade Computer Assembly A-23253

20-10551 20-10552 VIDEO CARD —\ POWER SUPPLY 20-10550 ASSEMBLY NETWORK INTERFACE CARD

20-10554 ‘A-23350 MOTHER BOARD HARD DISK DRIVE INTEL SE4408X—2 a ASSEMBLY

04-1687 COMPUTER CASE \

  • COOLING FAN

Parts 7-20

Page 117

Arcade Computer Mechanical Components

P-HEAD SCREW W/LOCK WASHER eV

4.12686, —FLBPeY Da MOUNTING SRACKET

P-HEAD SCREW W/LOCK WASHER amar

THUMBSCREW 6-32, 1/2" HEAD 2/4" 04-1268 CARD_RETENTION” BARS W/THREADED SCREW

2010807, 20-10557 ict 4 a | S10" 1 PaoceSsoR SDRAM DIMM 64M CELERON 333

P-HEAD SCREW W/LOCK WASHER / 6-2, 1/#

04-12686 —FARD DISK. DAVE MOUNT BRACKET

sonzserasan 3 VOLT LITHIUM —/ BATTERY

04-12687 COMPUTER Se

a 4.23350 BARD DISK DRIVE ASSEMBLY (OFFROAD. THUN

/ zososse | \8 FAN GRILLE van | 5795-15344-12 ay \__BARD Disk ORWE SELF TAPPING SCREW a RBEON CABLE #10 «1/2 \.

Parts 7-21

Page 118

Arcade Computer Cables

04-12657 RESET CABLE \

NOTICE: DC power cables are part of the power supply. You can’t replace these cables individually.

Parts 7-22

Page 119

Arcade Computer Electronic Components

20-10554

20-10557

20-10607

5882-16135-00

NOTICE: Many stock computers use a motherboard that resembles this one. Still, a standard motherboard won't function correctly in this video game machine. Operation in this VGM also requires a custom operating system.

NOTICE: Before attempting to use other than factory authorized parts, ask your distributor for information. Other DIMM and processor modules may be equivalent or superior to those illustrated here. Midway hasn’t verified performance with alternate components.

NOTICE: Celeron and Slot 1 are registered trademarks of Intel.

Parts 7-23

Page 120

Computer Motherboard Assembly 20-10554

=

Field Replaceable Parts

Component Description Board Location Part Number

Dual Inline Memory Module 64MB SDRAM DIMM BANK 0-1-2 20-10557

Memory Backup3-Volt Lithium BatteryB5882-16135-00
Processor AssemblyCeleron ProcessorJ4J120-10607
Processor CoolingFan with BracketFAN20-10549

Shunt Jumper BIOS Startup Configuration J8A1 5882-13046-00

Parts 7-24

Page 121

Network Interface Card Assembly 20-10550

Field Replaceable Parts

Component Description Board Location Part Number

Instruction ROM Not required in this game =

Parts 7-25

Page 122

Video Graphics Card Assembly 20-10551

Field Replaceable Parts

Component Description Board Location | Part Number Graphics Mode Select_| Not required in this game J6 =<

Parts 7-26

Page 123

Power Filter Board Assembly 04-12651

Field Replaceable Parts

Component Description Board Location Part Number

EMI Filter 2200 pF Dual Capacitor F1-F5 5060-15633-00 EMI Filter Ferrite Bead Inductor L1-L5 5556-14181-00

Parts 7-27

Page 124

BB12 Audio Amplifier Board Assembly 04-12529.1

Field Replaceable Parts

Component Description Board Location Part Number

Audio AmplifierLM3403 Quad AmplifierU1-U25370-15163-00
Audio OutputTDA1560Q Power AmplifierU35370-15984-00
Audio OutputTDA7375 Power AmplifierU45370-15833-00
Voltage Regulator+5VDC, 5% Fixed RegulatorU55250-13302-00

None Not required in this game U6 =

Parts 7-28

Page 125

MagicBus™ Interface Board Assembly 04-12697.3

facial} q

ane

aa]

J

Field Replaceable Parts

ComponentDescriptionBoard LocationPart Number
Crystal6 MHzY25520-16004-00
Diode1N270D11-15, D17-25, D285070-16229-00
Diode1N5817, 1AD25070-09266-00
Fuse5 x 20mm, 2ASBFA5735-13853-00
Jumper2-PinJP1, JP2, JP3, JP45791-13045-00
Transistor2N2369 NPNQi5190-15997-00
Transistor2N3904 NPNQ5-Q65160-14035-00
TransistorULN2064 NPNQ3-Q45160-14035-00

Parts 7-29

Page 126

Wheel Driver Board Assembly 04-12770.1

Field Replaceable Parts

ComponentDescriptionBoard LocationPart Number
=TO-92 DeviceQ4Not Used
Darlington2N6427 NPNQi5162-08976-00
DiodeFast FE6B-35nSD2, D35070-16272-00
Driver, PowerLM12 Op AmplifierU55370-14069-00
Fuse0.63AFB, 250V, 5x20mmF35731-15627-00
Fuse4ASB, 125V, 5x20mmFi, F25731-14094-00
Pre-DriverULN2064B ICU1, U25370-12602-00
Rectifier, Bridge100V, 6A, SIPBR15100-13945-01
Regulator, Voltage78L15, 15VDC, TO-92Q25250-15624-00
Regulator, Voltage79L15, -15VDC, TO-92Q35250-15625-00

Parts 7-30

Page 127

Speedometer/Tachometer Board Assembly 04-12759.1

Field Replaceable Parts

Component Description Board Location Part Number

LEDGreen, BrightLED1-65671-16256-00
LEDOrange, BrightLED7 - 105671-15953-00
LEDRed, BrightLED11 - 135671-15954-00

Parts

Page 128

Electronic Cable Assemblies

SERIAL COMMUNICATIONS CABLE (NULL MODEM DB-9F TO DB-9F)

20-10532

VIDEO COMMUNICATIONS CABLE (SHIELDED DB-15F TO DB-15M)

5797-13171-00

Parts 7-32

Page 129

Electronic Cable Assemblies

AUDIO AMPLIFIER CABLE (SHIELDED, MINIATURE STEREO PHONE PLUG TO PHONO PLUGS)

04-12578-2

COMPUTER RESET CABLE (2-PIN PLUG TO LOCKING, 2-PIN PLUG)

04-12657

Parts 7-33

Page 130

Line Cord Application Table

Part Number

ro @n cv @x on Bus BBs BBs BBs BBs

Country France Lal Germany Lal Italy Ld Japan Cy

Spain Lal

UK La! USA :

TYPICAL LINE CORD

Parts 7-34

Page 131

Parts 7-35 4004-01041-06 5102-14240-00 4-4 \ 4108-01219-11 5733-12869-00 ey ie

01-15054 ___4700-00015-00

04-12639.2 Line Cord Installation Bracket AC Plug Assembly A-23089

Page 132

Coin Door Application Table

ELECTROMECHANICAL COIN DOOR ASSEMBLIES art Number

Country 09-72000-14 09-72000-15 09-72000-20 09-96023-33

France Germany lm] 09-96011.1

Italy Japan Spain UK USA, DBV Ready

Transformer Application Table

POWER TRANSFORMER ASSEMBLIES Part Number

Line Power 5610-16282-00 5610-16283-00 5610-16284-00

120 VAC 60 HZ 230 VAC 50HZ 100 VAC 50HZ

TYPICAL POWER TRANSFORMER ASSEMBLY

Parts 7-36

Page 133

OFFROA:

TPTUN DE &

TROUBLESHOOTING

NOTICE: The term VGM refers to the video game machine.

CAUTION: This VGM uses complex electronic components that are very sensitive to static electricity. Observe the following precautions before handling VGM electronics. Failure to do so may void your warranty and could damage electronic assemblies.

Before servicing electronics, turn off AC power to the VGM. Wait for capacitors to discharge. Before touching or handling electronic assemblies, discharge static electricity on your body. To discharge this static, begin by connecting the line cord to a grounded outlet. Don’t turn on the VGM! Next, touch the safety ground stud of the power supply chassis. Store electronic assemblies in an anti-static area. Use anti-static bags to store or transport VGM circuit boards. Transport the hard drive in its shipping container. Don’t remove or connect electronic assemblies when cabinet power is on. Otherwise, you'll damage electronic assemblies and void the VGM warranty. After you complete maintenance or service, replace ground wires, shields, safety covers, etc. Install and tighten ground and mounting screws.

Troubleshooting 6-1

Page 134

Coin Mechanism and Pricing Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

« VGM (video game machine) accepts currency or tokens, but number of credits per coin or bill is incorrect. Improper settings at Pricing Menu Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Diagnostics Menu, choose SWITCH TEST. Use tests to confirm operation of switches.

FromAdjustmentsMenu,choosePRICING

MENU. Verify that units and credits are set correctly.

Faulty wiring Check that cabinet wiring is correct for this VGM.

Assurethat coinmeter and coinswitches

connect properly to control input wires.

« VGM won't accept currency or tokens.

¢ —VGM won't start.

« Audio and video are present. Improper currency Unlock and open cash door. Empty cash box. Inspect revenue for counterfeit currency. Check vault. Remove any items that block path from mechanism.

Faulty coin mechanism

Unlockandopencoindoor.Checkeach

mechanism for proper mounting. Remove mechanism. Clear currency path. Reinstall mechanism and latch it.

Tilted coin mechanism or VGM Va|ROD

e Verify that mechanism is level after doors close. Repair or replace coin door if it is bent or damaged. If necessary, adjust cabinet leg levelers to keep mechanisms vertical. ¢ — Coin indicators don't light Burned-out bulb Burned-out bulbs may appear white or darkened. Check continuity with DVM. Replace burned-out bulb with same type. Open fuse circuit ENaIN Check fuse continuity with DVM. If fuse is blown, replace fuse with same type. If fuse isn't blown, check wiring.

CAUTION: Don’t remove or install any connector when power is turned on. Installation under power will damage the circuit boards or hard disk drive and void the warranty.

o Typical Coin Mechanism Mounting

Troubleshooting 6-2

Page 135

VGM Startup Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

« VGM (video game machine) doesn't start.

« VGM appears completely non-functional.

  • No audio

¢ No illumination

« No video display Power problem Check that VGM power switch is on. Inspect computer to see if fans are turning. If not: Is computer power supply connected to its power cable? Is computer power supply turned on? Plug VGM into AC power outlet. Verify presence of AC line voltage.

Improper line voltage switch setting Turn off VGM power. Unplug AC line cord. Check line voltage switch. If necessary, set it to agree with local AC line voltage. Retest VGM.

Open fuse Turn off VGM power. Examine AC fuse at rear of VGM, on AC cord plug plate. Replace faulty fuses with identically rated parts. Turn on VGM power. If fuse opens again, check AC wiring harness and connectors.

Faulty wiring Remove line cord. Test line cord, power plug, and IEC connector for breaks or damage. Verify continuity of each wire in cord. Install cord at power chassis. Press connector firmly to seat it. Check computer cord in same manner. Assure that cabinet wiring harness connectors fully seat in corresponding power supply and board connectors. Inspect wiring for breaks or damage. Arcade computer problem Turn off power for one minute and turn VGM on again. Power On Self-Test checks electronics. Screen may report errors. If video circuits don’t operate properly, computer produces series of beeps. (See Error Message Troubleshooting Table.)

Location of Power Supply

Troubleshooting 6-3

Page 136

VGM Startup Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

  • Inspect circuit boards under low-light conditions. « VGM (video game machine) | Power problem LEDs glow if processor circuits receive voltage. appears non-functional. Fan should be turning. These indications prove presence of DC from power supply. Still,
  • Currency acceptor price voltages or signals may not be normal. indicator is illuminated. Computer has no internal LEDs.
  • Turn on VGM power. Using 20-volt DC setting on digital voltmeter, measure DC voltages at power connector pins. (Power supply voltage isn’t adjustable.)
  • Using 2-volt AC setting on digital voltmeter, measure same DC voltages as above. Any reading here indicates that supply voltages are unstable and may contain ripple or noise. Turn off VGM power. Assure that wiring harness Faulty wiring connectors fully seat onto mating board connectors. Verify that harness connects to computer. Check other connectors in same way. Improper jumper or Verify that circuit board jumpers are set as DIP switch settings intended. Check DIP switch settings.
  • Run power-up self-test sequence. Note errors or Faulty circuit boards failures during tests. Compare LEDs with LED or arcade computer indicator status charts. Note discrepancies.
  • Turn off computer. Wait for hard disk to stop spinning. Leave VGM power on. Loosen computer case thumbscrews and lift off cover. Turn computer power on. Listen for beeping sounds. Compare beeps with Error Message Troubleshooting Table.
CAUTION: Don’t remove or install any connector while power is turned on. Doing so will damage circuit boards or hard disk drive, and void warranty.

Front View of Coin Door Interior View of Electronics

Troubleshooting 6-4

Page 137

VGM Startup Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

doesn't start.

tokens. « VGM accepts currency or

« Audio and video are present. «¢ VGM (video game machine) | Faulty coin mechanism Unlock and open coin door. Check each currency acceptor to assure proper mounting. Verify that each release latch is closed and locked. Does mechanism accept and reject currency correctly? Test mechanism with good and bad coins. Inspect to see if external acceptor indicators (Pricing, Flashing Arrows, etc.) are lit. Verify that each acceptor operates properly by placing it in working VGM. Replace bad parts.

Faulty switches Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Diagnostics Menu, choose SWITCH AND LAMP. TESTS. Use tests to confirm operation of each switch in VGM. Assure that no loose parts or wires are caught in switch contacts. Check for continuity in each suspect switch connection (Common to Normally Open or Common to Normally Closed). Replace faulty switches (bent levers, broken actuators, etc.).

Faulty wiring Assure that no wires are caught in hinges, latches or switch contacts. Check wiring continuity from circuit board connectors to acceptors.

S Z

Interior View of Coin Door and Cash Door

Troubleshooting 6-5

Page 138

Audio Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

  • No audio

« Video is present

« VGM (video game machine) appears to operate normally Improper volume setting Enter Menu System by pressing and holding TEST MODE switch. From Operator (Main) Menu, choose VOLUME MENU. Check that Attract Music is on (enabled). Verify that all volume levels are set well above zero. If necessary, change levels to make VGM audible.

Faulty wiring Turn off VGM power. Assure that wiring harness connectors attach and fully seat onto mating board connectors. Verify that harness connects to computer. Also check audio connectors. Faulty or obstructed speaker Remove grilles and inspect speakers. Free speaker cones, terminals, mounting screws and magnets of loose parts or wires. Faulty Audio Board Verify proper operation of Audio Board by placing it in working VGM.

  • — Constant low hum from all speakers. Faulty wiring Check that cabinet wiring is correct for this VGM. Verify that cabinet wiring provides separate wires (not common return) for each speaker. Check connection of all cabinet ground wires.

Faulty Audio Board Run power-up self-test sequence. Note errors that VGM finds during tests. Verify that BB12 Audio Board operates by placing it in working VGM. If problem persists: Check regulator U5; capacitors C1, C2, C3, C14 and C30. Replace bad parts.

Faulty power supply Using 2 Volt AC setting on digital voltmeter, measure voltages at speaker terminals. Any reading indicates unstable supply that may contain ripple or noise.

« Audio is distorted, muffled or has missing frequencies. Faulty or improper speaker Turn off VGM power. Remove grilles and check speakers. Assure that speakers are full range (100 to 10,000 Hz response) and rated for at least 20 watts. Woofers must be rated for at least 40 watts. Verify proper speaker operation by connecting speaker in question to working VGM.

Faulty wiring Multiple-speaker installations: © Check for reversed wires at one speaker. Weak low frequencies and thin or hollow sound quality is symptom of incorrectly phased speakers. Sound tests may not detect this condition, but you can hear it during VGM operation.

¢ Dead sound channel Faulty speaker From Diagnostics Menu, choose SOUND TEST. Recheck speakers with audio signals provided by test. Verify proper speaker operation by connecting speaker in question to working VGM.

Faulty circuit board Run power-up self-test sequence. Note errors that VGM finds during tests. Compare circuit board LEDs with LED indicator status charts.

Note discrepancies.

Faulty wiring Verify that cabinet wiring is correct. Assure that all speakers connect to audio wires. Audio cable must be fully seated in Computer Line Output Jack. Check for broken or shorted wires.

Troubleshooting 6-6

Page 139

Error Message Troubleshooting Table

Power-On Self-Test Beep Codes Audio beeps only. Video may or may not be present. See notes. MESSAGE MEANING REQUIRED ACTION

No beepNo system powerCheck power supply and cables
1 continuous beepPartial system powerCheck power supply and cables
1 short beepNormal start; no errorsCheck other VGM components

2 short beeps Processor problem Check processor/fan module 3 short beeps Graphics initialization problem Check Video Board, cables

4 short beepsProcessor problemCheck processor/fan module
5 short beepsInsufficient system memoryCheck DIMM circuit modules
6 short beepsPeripheral problemCheck other VGM components

Notes «The audio buzzer that generates 1 kHz beeps is in the computer, inside the VGM (video game machine). If you have difficulty hearing beep codes, remove the rear cabinet door and computer cover.

« Arcade Computer circuit boards resemble those in personal computers. Yet Midway engineers reprogrammed the boards for application in this VGM. Power-On Self-Test codes are unique to the Arcade Computer in this VGM.

« Wiring or peripheral circuit problems may not trigger on-screen error messages. You may discover difficulties during Menu System diagnostic or calibration procedures.

e _ Forhelp with unresolved error messages, call your authorized distributor.

NOTICE: Don’t attempt to move computer circuit boards into alternate slots. Midway assigned boards to specific slots. The custom operating system won't recognize improperly placed boards, even though they function normally.

Troubleshooting Location of Beeper in Arcade Computer

6-7

Page 140

Link Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

«Can't connect VGMs (video game machines) together Faulty wiring Don't extend linking cables that come with VGM.

InstallrequiredcrossoverbetweenVGM

cabinets. Each coupler connects two cabinets (one pair). Don't use standard telephone type couplers or wiring to link cabinets. Use only 10 Base-T, Ethernet-type, Category 5, twisted-pair wiring for VGM data.

Improper linking hardware Use required network hub for your local network. Hub Link Kit permits up to four cabinet connections. Cabinet array completion requires basic kit brackets and spacers.

« VGM doesn't recognize other players in linking operation

e¢ VGM functions normally by itself Improper settings Record any error messages that occur during self-test.

FromOperator(Main)Menu,choose

Adjustments Menu. Then select Linked Play Adjustments Menu. Assure that you've set LINKED PLAY to ON. Be sure that each VGM has unique ID number. Power problem If hub is in use, verify that power is applied. AC adapter wires are thin and easily damaged.

Faulty wiring (3 or more cabinets) Inspect hub indicator lights. Each active port should have illuminated indicator. If cable connects, and that position has no lit indicator, check for cable continuity from hub to cabinet. Assure that no loose wires catch in hinges, doors, or under cabinet. Verify that linking cable connects to Network Board at each VGM's computer. Verify that each linking cable operates properly by placing it in working VGM.

« Some VGMs in group link properly, while others don’t Improper hub switch setting Assure that switches on hub are set correctly

accordingtoHubLinkKitinstructions.

(Networked cabinets don't require couplers. Hub has electronic crossover.) Inspect hub indicator lights for link activity. See manufacturer's literature for diagnostics.

Wrong software version Verify that all linked cabinets use same software

version.Otherwise,linkedcabinetswon't

recognize each other. Contact your distributor.

Faulty wiring (2 cabinets) Insert crossover connections between coupled cabinets. Standard couplers appear identical to devices supplied with cabinets, but don’t include internal crossover. Verify that each linking crossover coupler operates properly by placing it in working link between two cabinets.

Faulty wiring (3 or more cabinets) You used additional crossover connector and cable to extend VGM or hub link connection.

Twocrossoverscancelandcausesame

problem as no link crossover. Connect cables directly to hub. Don't use crossover coupler and hub together in single network. Separate communications wiring from other wiring. Wires that must cross should cross at right angles to limit noise pickup.

Troubleshooting 6-8

Page 141

Player Control Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

e Intermittent or completely non-functional player controls

« VGM (video game machine) starts normally. Faulty switches or lamps Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Diagnostic Menu, choose SWITCH TEST. Run tests to confirm switch operation. Check for loose parts or wires caught in switch contacts. Check continuity at each switch connection (Common to Normally Open or Common to Normally Closed). Verify that control operates properly by placing it in working VGM. Verify that dashboard switch light bulbs are type specified in parts listing. Other types light, but may produce too much heat. Eventually excess heat may cause switches to bind. Faulty switch wiring Check for wires caught in door hinges, latches, or switch contacts. Verify that harness connectors are attached and fully seated. Assure that control switches connect properly to control input wires. Check that cabinet wiring is correct for this VGM. « — Steering pulls to one side Faulty Wheel Driver Board Find power amp on Wheel Driver Board's large heatsink. Test and replace bad part or board.

How to Adjust Belt Tightness

Troubleshooting 6-9

Page 142

Player Control Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

Sloppy, unpredictable or ineffective steering

Video appears on screen

VGM (video game machine) starts normally Blocked or faulty fan With VGM power on, check airflow near each computer fan. Case cooling fans are intake fans. Power supply fan is exhaust fan. Assure that nothing blocks airflow.

Faulty mechanical parts Turn off VGM power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if your VGM has one) over motor. Inspect for faulty or worn belts, bearings, couplings, gears, etc.

Faulty Wheel Driver Board Inspect Wheel Driver Board under low-light conditions. LEDs glow if motor driver circuits receive AC power from transformer. (Voltages or signals may or may not be normal.) Examine fuses and cables on Wheel Driver

Board.Replacebadfuses.Usingdigital

voltmeter, verify AC voltage between each fuse

holder andground.Youshouldmeasure

approximately 25V. See Wiring Diagram. Using 20 VAC setting on digital voltmeter, measure DC voltage at motor. Don't move steering wheel, drive belt, or motor while making

thismeasurement.Anyreading _ indicates

unstable supply that may contain ripple or noise. Verify proper operation of Wheel Driver Board by placing it in working VGM.

Loose or worn drive belt Turn off VGM power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if your VGM has one) over motor. Inspect for faulty or worn belts, bearings, couplings, gears, etc. If drive belt isn’t worn or damaged, check its tightness.

No wheel feedback

Steering aims vehicle as expected Improperly set feedback

FromDiagnosticsMenu,chooseFORCE

FEEDBACK ADJUSTMENT. Set feedback to match player requirements. Maximum force may be too extreme for very young or inexperienced customers.

Faulty circuit Examine fuses and cables on Wheel Driver Board. Check cables and wiring between computer, interface, driver and motor. Check transformer and its connections. Replace bad parts.

Faulty motor Turn off VGM power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if your VGM has one) over motor. Unscrew caps. Inspect motor brushes. Replace worn parts.

Troubleshooting 6-10

Page 143

Player Panel Controls

WARNING: The Wheel Driver Board heatsink, power resistors, and other components may be very hot. The DC Motor in the steering wheel may also be hot.

MOTOR BRUSH

BRUSH H )THED STEERING ULLEY

ER

HED DRIVE PULLEY

MOTOR BRACKET—“

TER IN ADJUST BOLT—~

Steering Components

Troubleshooting 6-11

Page 144

Video Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

Verify connection of AC Power to video monitor.

«Monitor appears non-Power problemInspect CRT neck in dim light. Glowing filament

functional near CRT base proves that some monitor circuits receive power. Still, voltages or signals

*Audio is presentmay not be normal.
  • Turn off VGM power. Verify that video signal and
*VGM (video game machine) | Faulty wiringRemote Adjustment Board connectors seat

controls operate normally properly on Video Monitor Board.

  • Assure that video cables connect to circuit boards and computer.
  • Assure that no wires are caught on chassis or mounting brackets. Improper monitor Check that BRIGHTNESS (intensity) and adjustments CONTRAST are set above their minimum levels.
  • Examine AC line fuse on Video Monitor Board. If Faulty monitor fuse is faulty, replace it with identical fuse. circuitry 2. If fuse is good: Verify that video monitor operates correctly by placing it in working VGM.
  • If monitor is bad: Check monitor power supply.
  • If power supply is good: Check monitor horizontal output transistor and related circuitry.
WARNING: HIGH VOLTAGE. VGM (video game machine) monitors generate and store potentially lethal high voltages. Avoid touching any part of the monitor until power has been off for some time. A picture tube can maintain a hazardous charge for up to several days. Only qualified technicians should service monitors. Turn off the power, unplug the VGM and discharge the CRT before attempting service. Even properly discharged tubes can revert to a highly charged state, without reapplication of power.
WARNING: In normal operation, the monitor doesn’t require isolation from AC line voltage. During bench servicing, you may need to operate the monitor outside the cabinet. If you do, isolate the monitor from line voltage with an isolation transformer.

Typical Cutaway Rear View

Troubleshooting 6-12

Page 145

Video Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

VGM (video game machine) doesn't appear

No audio

Power-up self-test runs Floppy disk in drive Check floppy drive for diskette. If you find disk, eject it. Leave VGM power on. Turn off computer. Wait for hard disk to stop spinning. Turn on computer.

Faulty wiring Loosen computer case lid thumbscrews and lift off cover. Assure that hard drive ribbon cable connector is fully seated into mating connector on motherboard. Check hard drive power cable.

Improper components Verify that hard disk drive is correct for this VGM. Label on drive records manufacturer name, assembly number and program version. Verify that circuit boards are correct for this

VGM.Labeloneachboardrecords

manufacturer name, assembly number and hardware version.

Hard drive problems Turn computer on. Immediately look under hard drive. Hard Drive Activity LED flashes if drive is operating properly. Allow VGM to load normally. Note and record any error messages that occur during self-test. Remove hard drive and install it in working VGM. If symptom recurs there, hard drive is faulty. Replace it.

Blotches of color appear on screen Picture tube aperture mask is magnetized Remove diskettes from room. Demagnetize monitor with external degaussing coil. Take care not to magnetize neighboring VGMs. Monitor may be on or off for this procedure.

White areas in center of screen appear tinged with color

Object edges have fringe of one or more colors Picture tube purity or static convergence is out of alignment Turn on VGM. Press and hold TEST MODE to enter Menu

System.At Operator (Main)Menu,select

Diagnostic Menu. Then select Monitor Patterns Menu. Run through Crosshatch, Red, Green and Blue screens to find clearest display of problem. Display screen with greatest problem. Display Crosshatch Screen. Locate purity and static convergence ring magnets on back of monitor neck. Watch screen in mirror. Adjust

magnetstominimizeproblem.Follow

instructions from monitor manufacturer. Display Crosshatch Screen. Touch up adjustments while watching screen in mirror.

CAUTION: Don’t operate the monitor without its Remote Adjustment Board.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.

Troubleshooting 6-13

Page 146

Video Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

White areas at screen edges appear tinged with color

Dots at screen edges appear ovoid or cylindrical Picture tube dynamic convergence is out of alignment Have service bureau dynamically reconverge monitor. This procedure requires removing and repositioning yoke. Service bureau must follow instructions from monitor manufacturer.

Video tears or rolls, or has black bar down middle of screen Faulty wiring

Checkconnectorsandcablesforwiring

continuity. Video cables connect computer to circuit boards, and then to video monitor. Assure connection of all cabinet ground wires, especially at video monitor chassis.

Faulty monitor circuitry Verify that video monitor operates correctly by connecting it to working VGM. Assure that video monitor is correct type for this VGM. Video monitors with wrong resolution can’t lock sync.

Improper sync signals Check to see if Video Board puts out type of sync that your monitor requires. Verify that jumpers are set correctly for monitor. If necessary, add or remove video sync jumper at MagicBus Board jumper block JP4. With no pins connected (or pins 2 and 3 connected), board outputs positive sync. With pins 1 and 2 connected, board outputs negative sync. Electromagnetic fields

Movecabinetfarawayfrommachines,

appliances, or VGMs (video game machines). Missing colors Faulty wiring

Checkconnectorsandcablesforwiring

continuity from circuit boards to video monitor. Faulty monitor color drive circuitry Verify that video monitor operates correctly by connecting it to working VGM.

One color is dimmer or brighter than others

Whites appear tinted everywhere on screen Maladjusted color bias pots BONS

aoa Turn on VGM. Enter Monitor Patterns Menu. Watch Color Bars screen in mirror. Adjust three bias pots for best colors. (Most monitor neck boards include these pots.) Also check White Screen. Touch up controls. If whites still seem tinted, have service bureau rejuvenate picture tube.

Picture is dim or faded Maladjusted BRIGHTNESS pot or subnormal picture tube emission Watch Color Bars screen. Adjust BRIGHTNESS and CONTRAST pots for greatest number of grays. You'll find these pots on Monitor Remote Control Board, behind coin door. If pots have no effect, have service bureau rejuvenate picture tube.

Picture is too narrow Maladjusted WIDTH pot Enter Monitor Patterns Menu. Watch Crosshatch Screen while adjusting WIDTH pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.

Troubleshooting 6-14

Page 147

Video Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

¢ Picture is too short Maladjusted HEIGHT pot or damaged vertical circuit Enter Monitor Patterns Menu. Watch Crosshatch Screen while adjusting HEIGHT pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.

  • _If pot has no effect, service vertical output circuit. Enter Monitor Patterns Menu. Watch Crosshatch
  • Picture seems shifted to one | Maladjusted Screen while adjusting HORIZONTAL POSITION
sideHORIZONTALpot for best picture. You'll find this pot on Monitor

POSITION pot Remote Control Board, behind coin door.

  • Substitute working yoke.
¢Keystone-shaped pictureShorted turns in yoke | 2.Have service bureau converge monitor.

3.__ Retest monitor.

Software Update Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

« Update didn’t work

« After update procedure, screen reports lower than latest version You skipped steps or performed them out of sequence. Return update components to kit, reinstall original parts in cabinet, and try process again.

You connected linked VGMs (video game machines) to cabinet Network communication circuits may have prevented full update. Turn off power to all connected cabinets.

being updated.2.Perform update on one cabinet at time. If power

is off, you need not disconnect linking cables. Installation error may | 1. Inspect for bent or broken pins.

have damaged2.If you have another kit, try it.
device.3.__Ask your distributor to check your floppy disk.

NOTICE: Someday, software updates for your VGM (video game machine) might become available. These upgrades may improve your VGM’s performance or add new VGM features. Such upgrades tend to appear sometime after factory first releases VGM. Contact your distributor for information about updates.

Troubleshooting 6-15

Page 148

Miscellaneous Problem Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

« Marquee lamp is intermittent or non-functional

« VGM (video game machine) starts and plays normally Faulty fluorescent tube Remove fluorescent tube from its sockets. If you find cracks or darkened ends, install new lamp. Clean tube. Check continuity of both fluorescent tube filaments. Verify that fluorescent tube operates by placing it in working VGM. Faulty lamp fixture Verify that lamp pins make good connection with socket contacts. Faulty wiring Measure fluorescent lamp AC voltages. Check wiring and connector continuity from AC power chassis to lamp assembly.

« VGM operates normally

  • Cabinet becomes warm after several hours of use Obstructed fan Check bottom and rear of cabinet for blocked airflow. Move VGM away from sources of heat. Turn off VGM power. Remove dust from vent holes with high-power vacuum cleaner. Faulty wiring Check fan wiring and connectors.

Faulty fan Check operation of all fans.

« Error messages appear on screen Faulty hardware Check any assembly (RAM, ROM, Battery, etc.) identified in error messages. Call your authorized distributor for help with unresolved screen messages.

g &

Fan Location and Mounting Troubleshooting 6-16

Page 149

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 150

WARNINGS & NOTICES

WARNING e — Use of non-Midway parts or circuit modifications may cause serious injury or equipment damage!

e Use only Midway authorized components and parts. Failure to do so will void your warranty and may result in incorrect or unsafe operation. Substitute parts or modifications may void the EMC directive or FCC type acceptance.

e Federal copyright, trademark and patent laws protect this game. Unauthorized modifications may be illegal under Federal law. The modification ban also applies to Midway game logos, designs, publications and assemblies. Moreover, facsimiles of Midway equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with Midway Games Inc. components.

WARNING Prevent shock hazard and assure proper game operation. Plug this game into a properly grounded outlet. Don't use a cheater plug to defeat the power cord's grounding pin. Don’t cut off the ground pin.
WARNING A small portion of the population has a condition which may cause epileptic seizures or momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons experience seizures while watching some television pictures or playing certain video games. People who have not had seizures may nonetheless have an undetected epileptic condition.

If anyone in your family has experienced symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), consult your physician before using video games.

Parents should observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, discontinue use immediately and consult your physician.

NOTICE This video game machine was tested. It complies with limits for a Class A digital device, under FCC Rules, Part 15. These limits provide reasonable protection against harmful interference when the equipment operates in a commercial environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to the instruction manual, this equipment may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference. If interference occurs, the user must correct it at his own expense.

NOTICE When Midway Games Inc. ships a game, it complies with FCC regulations. Your FCC label is proof of compliance. Legal repercussions to the owner or distributor may result if the label is missing or damaged. If your game does not contain an FCC compliance label, call Midway Games Inc. immediately.

NOTICE You may not reproduce any part of this publication by mechanical, photographic, or electronic means. You may not prepare phonograph recordings of this document. You may not transmit this publication or otherwise copy it for public or private use, without permission from the publisher.

COPYRIGHT & TRADEMARK NOTICE Entire contents of this manual copyright ©1999 Midway Games Inc. All rights reserved. Midway® and Offroad Thunder™ are trademarks of Midway Games Inc.

FOR SERVICE Call your authorized Midway Games distributor.

MIDWAY GAMES INC. 3401 N. CALIFORNIA AVE. CHICAGO, ILLINOIS 60618-5899 USA