Marvel
Marvel Super Heroes (Europe 951024) (Capcom, 1995) · Document · 22 pages · 22 sections · original scan
OPERATORS MANUAL
/\\, WARNING
This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be construed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.
CARCOMY COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (847) 797-6192 PM00132-KIT Fax: (847) 797-6306 022296
CARCOMMR Res MARVEL SUPER HEROES™
THANK YOU FOR PURCHASING MARVEL SUPER HEROES™ VIDEO KIT. WE
INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:
CAPCOM® COIN-OP, INC. ATTN: FIELD SERVICE - VIDEO PRODUCTS 3311 N. KENNICOTT AVENUE ARLINGTON HEIGHTS, ILLINGIS 60004 PHONE: (847) 797-6100 FAX: (847) 797-6305
THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.
AAMA See Rune SERLAL NUMBER SERIAL NUMBER
“A’ CARTRIDGE SERIAL NUMBER (BOTTOM OF CASE) 300900
DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE:
“FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL #
AAMA SERIAL #
“A” KIT A-CARTRIDGE SERIAL #
“B” KIT B-CARTRIDGE SERIAL #
Proprictary and confidential information, wut w be ductoved or copied wilinns: tbe expres permumpan af CAPLOM® COIN-OP, ENC.
@APROT? coin-op, nc. MARVEL SUPER HEROES™
TABLE OF CONTENTS
Warranty Information
Kit installation “FULL” Kit Preparation Installation Marquee Control Panel Wiring Test Bracket Game Cartridges “A? & “B” Kit Preparation and Installation seeveensresiea vanes eerenertnesesenessensrassaesaessaatsesisassienssaesansansee
Test Mode Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions Configuration Menu System Configuration Game Configuration
Cable Wiring JAMMA Connections Auxiliary Cable Connections
Template : Control Panel Drill Hole(s)
Proprietary and cunfidential information, net ta ba disclosed or cupid witht the cupress perminaon of CAPCOM COIN-OP.ING.
CAPCCLcom-or, inc. MARVEL SUPER HEROES™
NOTES
ii [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
ICAR COM eas MARVEL SUPER HEROES2
KIT INSPECTION
There are three kits available for conversion to MARVEL SUPER HEROES™.
- MSHL0Q00E (“FULL” kit) contains the complete game cartridges, all necessary graphics, and replacement joysticks and button switches. The “FULL” kit is intended for conversion of most JAMMAcompatible, horizontal screen cabinets.
- MSH1000AE (“A” kit) is compatible only with current CAPCOM® System II games. It is similar to the “FULL” kit but does not include both cartridges (only the A-cartridge is supplied). For operators who have previously converted a cabinet with a “B” kit, the purchase of an “A” kit will provide all the additional components necessary for “FULL” cabinet conversion (“A” + “B” = “FULL”)
- MSH1000BE (“B” kit) contains the game software cartridge (B-cartridge) and must also be installed to a current CAPCOM® System I game. It includes all the necessary game graphics for a cabinet conversion (marquee, control panel overlay, monitor card, etc.).
Check that all parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.
KIT PARTS LIST
MSH1000E | MSH1G00AE_| MSH1000BE PART NO. DESCRIPTION ary
| A-00532 | CPS II System Cartridges (A/B ) | 1 | |||
| qv | ZZ1400A | CPS II System Cartridge ( A) | 1 | ||
| Vv | A-00533 | CPS II System Cartridge ( B ) | 1 | ||
| Fi | q | AWO00174 | Monitor Card | C1 | |
| v | ¥ | AW00171 | Marquee | 1 | |
| v | v | AW00173 | Overlay, Control Panel | 1 | |
| ae | v | AWO00175 | Decal, Joystick & Button Switches | 1 | |
| a | ¥ | AWO00176 | "| Decal, Cabinet Side | 2 | |
| V | v | AW00172-01 | Decal - Left, Game Play Instruction | 1 | |
| v | v | AW00172-02 | Decal - Right, Game Play Instruction | 1 | |
| v | ¥ | ¥ | PM00132-EUROKIT | Manual, Operators | 1 | |
| v | v | 03-0052 | Cable, Auxiliary | 1 | |
| v | v | GE2030 | Joystick | 2 | |
| v | y | 16-0130 | Switch, 1-Player Start Button (White) | 1 | |
| V | ¥ | 16-0131 | Switch, 2-Player Start Button (White) | 1 | |
| V | v | 16-0133 | Switch, Punch/Kick Button (Red) | 4 | |
| V | v | iz | 16-0134 | Switch, Punch/Kick Button (Blue) | 4 |
| v | Vv | 16-0147 | Switch, Punch/Kick Button (Yellow) | 4 | |
| v | v | 03-0050 | Bracket, Volume/Test | 1 | |
| v | v | 13-0066 | Bracket, A-Cartridge Mounting | 4 | |
| V | v | $C00104-05 | Screw, Wood | 4 | |
| v | 13-0141 | Clamp, Case | 2 |
[Proprietary and confidential information, not to be disclosed or copied withaut the express permission of CAPCOM COIN-OP, INC. 1
ICAR COME ce MARVEL SUPER HEROES™
[ CAUTION
Please read the following instructions to keep the PC board in good condition:
- Do not block the ventilation slots.
¢ Do not drop or bump the board.
¢ Do not spill any liquids on the case.
e Do not disassemble the case.
ATTENTION
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste system. Check with your local solid waste official for Ni-cd details in your area for recycling options or proper disposal.
DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY
OF YOUR REPAIR WARRANTY.
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
Cy GAPE comn-op, inc.
“FULL” KIT INSTALLATION
MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.
PREPARATION
- Disconnect and remove the old printed circuit board(s) or cartridges from the cabinet.
- Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
- Remove any covering from the control panel overlay, and then remove the control panel overlay.
- Place the Drill Hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
- Cut out the new holes using a 1-3/16" hole saw.
- If there is an additional control panel *cover {such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *Cover is not included in the kit.
- Plug up unused holes with a wood dowel (1- 1/8" diameter) and sand any rough edges.
INSTALLATION
Marquee Installation
- Remove the marquee glass, old marquee overlay, and the old cabinet graphics.
- Install the new marquee and replace the *glass. *Glass is not included in this kit.
Control Panel Overlay Installation (See Figure 1)
- The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges. MARVEL SUPER HEROES™
- Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
- Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
- Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
- Install the control panel *cover (if required).
Figure 1 Overlay Installation
Reassembly of Components
- Install all buttons and retaining rings on the control panel as shown in Figure 2. Install two RED buttons to the immediate right of each joystick, install two YELLOW buttons to the right of the red ones, and install two BLUE buttons to the right of the green ones.
[Preity a soni foram ot b endo cped witout is Gps perminion of CAFCOM@ COMVOR ING] 3
Cy CAPCON COIN-OP, INC. MARVEL SUPER HEROES™
Control Panel Red Yellow Blue Red Yellow Blue
Red Yellow Blue Red Yellow Blue
Buttons )
iP yet SS ) Ss Retaining eS ia Rings 4 g Switch se witches ee é FIGURE 2 FIGURE 4 Control Panel Buttons and Switches Joystick Installation
- Notice that there are two white buttons. (See Figure 3.) The WHITE buttons are START buttons. Install the PLAYER ONE button on the top lefthand side of the control panel, and the PLAYER TWO button on the top right-side of the control panel.
I Player 2 Player
FIGURE 3 Start Buttons
- Instail the switches on the buttons as shown in Figure 2. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
- Install the joysticks on the control panel as shown in Figure 4. CABINET DECAL INSTALLATION
19, Remove monitor glass and install monitor card.
- Peel-off the backing to the instruction decals and place on both the left and the right sides of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.
MONITOR CARD INSTRUCTION DECAL-LH
‘CABINET DECAL INSTRUCTION DECAL - RH
FIGURE 5 Cabinet Decal Installation
4 [Pris and conta norton no don or Gd Wit pron pra of CAPCOM COMTOR NE]
CARGO coin-op, inc. MARVEL SUPER HEROES™
WIRING TO GAME CASE CONNECTOR
- Reconnect the existing JAMMA connectors to ‘SWITCHES the control panel according to the chart in Figure 5.
To VOLUME
22. Connect the Player 1 and the Player 2 Kick eunrches
buttons to the auxiliary cable harness connectors shown in Figure 6. Make the connections according ae FIGURE 6 to the chart in Figure 7. Auxiliary Cable Harness
JAMMA CONNECTS
CONNECTOR REF. *WIRE COLOR TO COMPONENT FUNCTION PLAYER | JOYSTICK
| WHITEBROWN | PLAYER | | JOYSTICK, |
| WHITE/RED. | PLAYER 1 | JOYSTICK |
| WHITE/ORANGE | PLAYER 1 | JOYSTICK, |
PLAYER} PUNCH BUTTON,
| WHITE/GREEN | PLAYER | | PUNCH BUTTON, |
| WHITE/BLUE | PLAYER | | PUNCH BUTTON |
| VIOLETBLACK | PLAYER2 | JOYSTICK |
| ‘VIOLET/BROWN | PLAYER 2 | JOYSTICK |
| VIOLET/RED. | PLAYER 2 | JOYSTICK |
| VIOLET/ORANGE | PLAYER 2 | JOYSTICK |
| VIQLET/YELLOW. | PLAYER 2 | PUNCH BUTTON |
| VIOLET/GREEN | PLAYER 2 | PUNCH BUTTON |
| VIOLET/BLUE. | PLAYER 2 | PUNCH BUTTON |
Figure 6: JAMMA Wiring Connections
- Wire Color Note: — Wire colors shown are according to the AAMA -AMOA Standard for wire color assignments; your harness may contain different colors than shown above.
UXILIARY CABLE CONNECTS CONNECTOR REF. WIRE COLOR TO COMPONENT FUNCTION
| BLACK | PLAYER! | KICK BUTTON | COMMON |
| BLUE | PLAYER 1 | KICK BUTTON | UGHT |
| RED | PLAYER | | KICK BUTTON | MIDDLE |
PINK PLAYER 1 KICK BUTTON HEAVY BLACK PLAYER 2 KICK BUTTON ‘COMMON
GRAYNELLOW PLAYER 2 KICK BUTTON LIGHT
| PINK/YELLOW. | PLAYER 2 | KICK BUTTON | MIDDLE |
| PURPLE/YELLOW | PLAYER 2 | KICK BUTTON | HEAVY. |
| GRAY/VELLOW | TEST BRACKET | VOLUME SWITCH | UP |
| PINK/YELLOW, | TEST BRACKET | VOLUME SWITCH | DOWN |
| BLACK/WHITE, | TEST BRACKET | VOLUME SWITCH | COMMON |
Figure 7: Auxiliary Cable Wiring Connections
Tron and ee rgb nb Sd apd a Ue as palin ot CAPCOM CONTE NE] 5
ICARCOMY COIN-OP, INC.
- An optional Test/Volume bracket (see Figure 8) is included in this kit. Your cabinet may already contain this bracket. If you decide to install, the bracket should be mounted inside the coin door and on top of the cash box for easy access.
‘¥300500
Figure 8: Test Bracket
Wiring of the Test Bracket requires connections to both the main JAMMA harness as well as the auxiliary cable harness (refer to Figure 9).
SWITCH CONNECTS
FUNCTION TO
VOLUME-UP | AUX. CABLE ‘29°(GRAY/ YELLOW) COMMON AUX. CABLE “31°(BLACK/ WHITE) VOLUME- DOWN AUX. CABLE “30° @PINK/ YELLOW) AUX. CABLE “31°(BLACK/ WHITE) JAMMA “15° COMMON
JAMMA ‘A’ or ‘B’ or ‘e’ or ‘f or ‘1’ or ‘2’ or ‘27° or ‘28° Figure 9: Test Bracket Wiring Chart MARVEL SUPER HEROES™
GAME CARTRIDGE INSTALLATION
- Instali the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 10,
Z
Figure 10: Mounting Bracket Installation
- Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 11.
Figure 11: Case Mounting
- Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q- SOUND, also attach the audio cables.
6 Proprietary and confidential information, not to he disclased or copied without the express permission of CAPCOM COIN-OP, INC.
® CAR COM
Improper installation of the JAMMA harness connector to the game cartridge will cause damage to the enclosed PCB.
- Power-up the game and set ali operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.
“A” KIT INSTALLATION
- To install the contro] panel parts, you must follow the “FULL” Kit Preparation and Installation Procedure, steps 15 through 18, and steps 21-23.
- To mate the existing “B” cartridge with the “A” cartridge, align the “B” cartridge over the “A” cartridge and push down firmly. Install the case clamps as shown in Figure 12.
Figure 12 : Case Clamp Installation MARVEL SUPER HEROES™
- Continue to follow the “FULL” kit Preparation and Installation Procedure, steps 25 through 27.
4, Installation of the “A” kit is now complete.
DISASSEMBLY OF EITHER GAME CARTRIDGE WILL VOID YOUR WARRANTY.
“B” KIT INSTALLATION
1, To install the cabinet graphics, you must follow the “FULL” Kit Preparation and Installation Procedure, steps 3 through 22.
- To remove the existing “A” cartridge from the “B” cartridge, pull the old case clamps apart and discard (see Figure 12). Carefully remove the old “B” cartridge and instal] the new “B’ cartridge. Install the new case clamps.
- Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 7
CAPEEN coin-op, inc. MARVEL SUPER HEROES™
NOTES
8 [Proprietary and confidential information, not to be disclased or copied without the express permission of CAPCOM® COIN-OP, INC.
CNP@OM co-op, inc. MARVEL SUPER HEROES™
TEST MENU
The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin mechs, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.
L ACCESSING THE TEST MENU
- For a CAPCOM® cabinet, or a cabinet with a test switch: Make sure the game is on and push the test switch. The screen shown below will appear.
- For a cabinet without a test switch: Push the test switch test on the outside of the blue plastic casing. (Refer to the inside back cover of the manual}.
TEST MENU
INPUT
OUTPUT
SOUND & VOICE
COLOR
DOT CROSS HATCH
GAME DATA
CONFIGURATION
- MEMORY CHECK
- EXIT
SELECT = 1P UP or DOWN START =1P SHOT?
- HOW TO SELECT AN ITEM
- Use the PLAYER J JOYSTICK to move the arrow in front of the desired item and press the PLAYER I LIGHT PUNCH button.
- To retum to the test menu, push the PLAYER ] START and PLAYER 2 START buttons simultaneously.
- The test menu will always appear on the screen:
- After you exit the “7. CONFIGURATION MENU” and
- After the memory is tested from the menu, “8. MEMORY CHECK”.
- CLOSING THE TEST MENU
To close the Test Menu, highlight “9, EXIT” and push the PLAYER 1 LIGHT PUNCH button.
Peers ‘and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP. INC,| 9
ICARCOMY ‘COIN-OP, INC. MARVEL SUPER HEROES™
- TEST MENU ITEM DESCRIPTIONS
INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved.
OUTPUT Used to test the coin meter and the coin lock.
SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER / JOYSTICK. Push the PLAYER I LIGHT PUNCH button to hear the sound of the selected code.
COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background.
DOT CROSS Used to test the screen size, focus and distortion. HATCH GAME DATA Coin meter and playtime information will be displayed.
CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section.
MORY CHECK Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of maifunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears.
EXIT Select this item and push the PLAYER I LIGHT PUNCH button to retum to game play mode.
10 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CARSON coin-op, Inc. MARVEL SUPER HEROES™
CONFIGURATION MENU
The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB rather than DIP switches.
The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.
1, ACCESSING THE CONFIGURATION MENU
« From the TEST MENU, move the arrow to “7. CONFIGURATION” and push the PLAYER 1 LIGHT PUNCH button. The screen below will be displayed. A description of each option is explained in the table below.
- CONFIGURATION MENU
- SYSTEM
. GAME
. DEFAULT
. SAVE & EXIT
SELECT = 1P UP OR DOWN START = 1P LIGHT PUNCH
SYSTEM Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER I LIGHT PUNCH and PLAYER | MIDDLE PUNCH buttons at the same time to select this option. SAVE & Use this to save new configuration settings and exit to the Test Menu. The message EXIT “SAVING NEW CONFIGURATION IN EPROM” will appear while the new settings are being saved. DO NOT tum power off to the game until “SAVING” is complete and the Test Menu reappears.
Proprietary and confidenval information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OF, INC. 1
'® ARCOM OP, INC. MARVEL SUPER HEROES™
SYSTEM CONFIGURATION
CHANGING THE SYSTEM CONFIGURATION SETTINGS
Move the PLAYER | JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER J JOYSTICK left or right or press the PLAYER ] LIGHT PUNCH button to select.
7-1. SYSTEM CONFIGURATION
- COIN MODE 2 COINS 1 CREDIT
. CONTINUE ON
. MONITOR NORMAL
- DEMO SOUND ON
. SOUND MODE STEREO (QSOUND)
. CHUTE TYPE 1 CHUTE SINGLE
. EXIT.
SELECT OPTION = 1P UP OR DOWN MODIFY SETTING = 1P LEFT OR RIGHT = 1P LIGHT PUNCH OR JUMP
SYSTEM CONFIGURATION ITEM DESCRIPTIONS
- COIN SELECT THE CHARGE PER PLAY.
- CONTINUE SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY.
- MONITOR FLIP. FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL.
- DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF.
- SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET.
- CHUTE TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTES. 1 CHUTE SINGLE: WITH THIS SETTING, EITHER PLAYER CAN START THE GAME. 2 CHUTES SINGLE: TWO PLAYERS USE ONE COIN CHUTE AND PLAY AT THE SAME TIME. THE PLAYER WHOSE COIN WAS PUT IN FIRST STARTS THE GAME. 2 CHUTES MULTI: TWO PLAYERS USE TWO COIN CHUTES AND PLAY SEPARATELY. THE GAME STARTS FROM THE SAME SIDE AS THE COIN CHUTE WAS USED. TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH. THE PLAYER I START BUTTON.
SYSTEM CONFIGURATION OPTION SETTINGS
| 1COIN | 1 COIN | COIN | 1 COIN | |
| 1 CREDIT | 2CREDTTS | 3 CREDITS | 4CREDITS | |
| 1 COIN | 1 COIN | 1 COIN | 1 COIN | |
| 6 CREDITS | 7 CREDITS | 8 CREDITS | 9 CREDITS | |
| ‘3 COINS | ‘4 COINS | ‘5 COINS: | 6 COINS | ‘7 COINS |
| 1 CREDIT. | 1 CREDIT | L CREDIT | 1 CREDIT, | 1 CREDIT |
| 8 COINS | 9 COINS | 2. COINS START. | FREE PLAY | |
| 1 CREDIT | 1 CREDIT, | 1 COIN CONTINUE |
2, CONTINUE, aS eS ON 4 | 3, MONITOR
- DEMO SOUND |e" 5.SOUND MODE ix: 3 “S STEREO (Q SOUND) 6, CHUTE TYPE, FLIP ‘gov, ONSS. MONAURAL T CHUTE SINGLE @HUTES SINGLE 2. CHUTES MULTI 7, LANGUAGE E 5 SENGLBE: SPANISH PORTUGUESE,
Proprietary and confidential information, not to he disclosed oF copied without the express permaission of CAPCOM® COIN-OP, INC.
CAPCOM" coin-op, Inc. MARVEL SUPER HEROES™
GAME CONFIGURATION
CHANGING THE GAME CONFIGURATION SETTINGS
Move the PLAYER | JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER } JOYSTICK left or right or press the PLAYER I LIGHT PUNCH button to select.
7-2, GAME CONFIGU:
. DIFFICULTY
. DAMAGE LEVEL
. TIMER SPEED
|. MAX ROUND ATION
4 MEDIUM
LEVEL 4
4 NORMAL
3 ROUNDS
. JOIN-IN ON
. EVENT OFF
. MODE NORMAL TURBO
. EXIT
SELECT OPTION MODIFY SETTINGS P UP OR DOWN P LEFT OR RIGHT +P LIGHT PUNCH OR MIDDLE
GAME CONFIGURATION ITEM DESCRIPTIONS
- DIFFICULTY SETS THE DIFFICULTY LEVEL.
- DAMAGE (INFLICTED) LEVEL SETS THE LEVEL OF DAMAGE INFLICTED ON OPPONENTS (OFFENSIVE POWER).
- TIMER SPEED SETS THE SPEED OF THE COUNTDOWN FROM THE TIMER DISPLAY
- MAX ROUND SETS THE NUMBER OF ROUNDS PER MATCH: 1 ROUND: WINNER OF A SINGLE ROUND WINS; 3 ROUNDS: WINNER OF 2 OUT OF 3 ROUNDS WINS; 5 ROUNDS: WINNER OF 3 OUT OF 5 ROUNDS WINS. S_JOIN-IN SETS THE OPTION TO ALLOW OTHER PLAYERS TO JOIN-IN.
- EVENT TURNS ON EVENT MODE. USEFUL FOR CHAMPIONSHIP TOURNAMENTS. OFF: NORMAL SETTING. SETS THE MODE TO NORMAL OPERATION. 1 MATCH: MATCHES PLAYER WITH ONE CREDIT. A WIN OR A LOSS RESULTS IN GAME OVER (CONTINUE IS NOT AVAILABLE). ALLOWS FOR AN AUTOMATIC BLOCKING FEATURE FOR MOST CHARACTERS (TO BE USED FOR BEGINNING PLAYERS). RETURN TO THE CONFIGURATION MENU.
GAME CONFIGURATION OPTIONS
- DIFFICULTY 4 5 iz 7 EASIEST .
MEDIUM MEDIUM VERY HARD
HARD. 2 3 8 VERY EASY | EASY HARD HARDEST
- DAMAGE LEVEL VEL 1 LEVEC2 [LEVEL LEVEL 4 LEVELS LEVEL7 | LEVELS
- TIMER SPEED "|
- MAX ROUND. ‘5 ROUNDS. 5-JOIN-IN
- EVENT,
- MODE
Proprietary and confidential information, not to be disclosed ar copied without the express permission of CAPCOM® COIN-OP, INC.
ty CAPCOM COIN-OP, INC. MARVEL SUPER HEROES™
JAMMA Connections
SOLDER SIDE COMPONENT SIDE
GND GND +5 VDC +5 VDC NC. +12 VDC KEY COIN COUNTER 1 COIN LOCK 2 Ref g0|~aforfea fn |eofro]—
*SPEAKER () COIN LOCK 1 *SPEAKER (+) NC. NC. VIDEO RED VIDEO SYNC. SERVICE (FREE CREDIT) VIDEO BLUE VIDEO GROUND DIAGNOSTICS 1 PLAYER - COIN
2 PLAYER - UP 2PLAYER - DOWN 1 PLAYER - START 1 PLAYER - UP 1 PLAYER - DOWN 2 PLAYER - LEFT 1 PLAYER - LEFT. 2 PLAYER - RIGHT 2 PLAYER - LIGHT PUNCH 1 PLAYER - RIGHT L PLAYER - LIGHT PUNCH 1 PLAYER - MIDDLE PUNCH 2PLAYER - MIDDLE PUNCH 2 PLAYER - HEAVY PUNCH NC 1 PLAYER - HEAVY PUNCH NC NIC NIC GND GND GND “PREP RNSPERERPRERP ERP
GND
PLAYER 2 HEAVY KICK NIC NC
GRAY/YELLOW PLAYER | HEAVY KICK PLAYER | MIDDLE KICK PLAYER 1 LIGHT KICK PLAYER 2 LIGHT KICK PINK/YELLOW PLAYER 2 MIDDLE KICK NC NC GRAY/YELLOW | TEST BRKT-VOLUME UP
BLACKMWHITE TEST BRKT- VOLUME COMMON BLACK PLAYER 2 KICK - COMMON TEST BRKT-VOLUME DOWN _| PINK/YELLOW. NIC NIC NC TNC
NIC PLAYER 1 KICK-COMMON BLACK
[Proprietary and confidential information, not to be disclosed or copied without the express permimion of CAPCOM COIN-OP, INC.
4" DRILL FOR
YSTICK HOLE
*ON NOISIAS# onZzN0gA, WP CAG NMVHd 96/92/0l “ALY SLVIdWAL Ted SAOUSH YadNS TAAUYA vOC09 SIONITH *
SLHOIBHNOLONTY QY LLODINN3Y HLHON 11ce 7 “ONL WOOd¥D SATOH NOLLNG HOd TWH .Qb/E-b CvoldAD SNIT Wid
CAPESLD comop, inc. MARVEL SUPER HEROES™
GAME CASE CONTROLS
Me, | (ROTUSED) COMMUNICATION FORTS (NOT USED) (NOT USED) +
*VOLUME DOWN
JAMMA AUXILIARY CABLE AUDIO OUT (FOR Q SOUND} CONNECTOR CONNECTOR RIGHT: RED, LEFT: WHITE. 17900800
*NOTE: IF YOU ARE EXPERIENCING VOLUME CONTROL PROBLEMS, DEPRESS AND HOLD VOLUME DOWN FOR AT LEAST 5 SECONDS AND RELEASE. THEN, SET VOLUME UP FOR APPROPRIATE SOUND LEVEL. FOR SOUND LEVEL VERIFICATION, FOLLOW THE INSTRUCTIONS IN THIS MANUAL UNDER TEST MENU AND SELECT SOUND & VOICE.
TYPICAL CONTROL PANEL LAYOUT OF MARVEL SUPER HEROES™
Proarietary amd confikential infortmation. wot to Ibe diarknaed or comied withous the exnreca perminion of CAPCOM® COIN<0P. INC._|
NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
WARNING
Federal aw provides severe civil and criminal penalties tor the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.
The Federai Bureau of Investigation investigates allegations of criminal copyright infringernent.
CARCOMYg COIN-OP, INC. 3311 N. Kennicott Avenue Artington Heights, Illinois 60004 Phone: (847) 797-6100 Fax: (847) 797-6306
Copyright © 1995 CAPCOM © coin-op, Inc., All Rights Reserved