CATHODE RAY TOMES

Ace Driver Installation

Ace Driver (Namco, 1994) · Installation · 31 pages · 13 sections · original scan

Page 1

ACE DRIVER

DELUXE

Installation and Commissioning

Manual

IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY.

Part No. 90500031

Page 2

© 1994 PIAMMCO Les - all rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for public or private use, without permission from mamca Lid.

While the information contained in this manual is given in good faith and was accurate at the time of publication, BRENT LEISURE LIMITED reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with European Community directives (1st. January 1995), and as such bears the C € marking. Any changes or modifications to this machine must be in accordance with European Community directives (1st. January 1995).

If you make any unauthorised changes to this product, you may contravene European Community directives (1st. January 1995)

Published by: BRENT LEISURE Ltd. Unit 1 Brent Crescent, London. NW10 0QT

Phone:- 0181-965-0550 Fax:- 0181-961-0574

Page 3

This machine is designed for indoor use only. Do not install the machine in the following places.

[® Direct sunlight, places with excessive humidity or dust, places where there is water leakage, near airconditioning or heating equipment, places with excessively high or cold temperature.

[ @® Places where it would be in the way of emergency exits or fire extinguishing equipment.

Page 4

SAFETY WARNING

In Order to Use This Machine Safely

In order to use this machine safely, be sure to read this Installation and Commissioning manual and the Operators Manual carefully before installation and use of the machine. Whenever the owner of this machine entrusts disassembly, installation, adjustment, routine maintenance or trouble shooting to another person, the owner should ensure that they read the appropriate precautions and relevant sections of this manual before starting work. In order that no accidents occur when the machine is in operation, strictly follow the notes on safety described below. Do not turn the machine ON until it has been correctly installed.

Warnings for Operation (~ NOTE:

NOTE:
NOTE:
NOTE: Only operate this machine after checking that it has been installed correctly in accordance with this Installation and Commissioning manual. Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There are warning stickers to keep hands and feet clear of moving parts, however if the operator feels that a customer playing the game is in any
danger, he should warn the customer accordingly. The warning stickers must always be kept in good condition and replaced if worn so that the customer can read them clearly. If there is an error or problem with this machine, operation must be stopped immediately.

Warnings for Disassembly, Installation, Routine Maintenance and Troubleshooting

Va

DANGER:
DANGER:
DANGER:
DANGER:
NOTE: ~ Namco Ltd. bears absolutely no responsibility for accidents or injuries resulting from unauthorized changes to the machine. Ensure that the machine has been turned OFF before making adjustments or carrying out maintenance. Also ensure only qualified personnel carry out maintenance or turn the power ON to this machine. The power supply and inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is a possibility of burns or electric shock. Be careful not to touch these areas. In order to avoid injuries due to mis-operation, be sure that the voltage of the power supply is within the prescribed limits. Also to prevent possible electric shocks due to failure, this machine MUST be fitted with a securely connected earthed plug. Do not turn the main power switch ON until the machine has been installed correctly. /
Page 5

Contents

INSTALLATION ........cccecccsceeseeeeescseseceseeececseseceseseseseeseseseseeesseseseveeeeeesseeee 7

1-1 Installing the Sign Assembly .......... ccc eee cee eeeeeceaeneeseeceeaeeecseeeeseaeeeeeaeene 8 1-2 Installing the Sign Boards (L), (R) ......:cccccceesesscsesesesssseeesesssseeseeeeesssesseseaeessesansees 9 1-3 Connecting the Seat Assemblies to the Tower Assembly ...........cccsssssesseseeeees 10 1-4 Removing the Shipping Brackets 1-5 Installing the Guard Fence 1-6 Applying the Number Sticker: 1-7 Linking Two or More Machines. ..........cccccceseseceessssseseseeeeeeesessseseseeeessesesseseaenee 16 1-7-1 Setting the Link Switches ...........cccscsssseseeeeeeeeteseeeeeeeeeessesseseseeneneesesaeaee 17

ADJUSTMENTS... eiccccececeeees rece ceceeeeesesecesesseeesessesecesseeesesseeesesseeetenags 18

2-1 Turning on the Power 2-2 Adjustment Switches. 2-3 Test Mode 2-3-1 COIN Option ........ececeeceseesessseseseescscseseeeeeesessseeeessessessesessassnseseeneecseseaetes 2-3-2. Game Options 2-3-3 W/O Test

2-3-4: Switeh TeSt sccr.cccrssnsersrrerscnecssensecsenssasenssoanvacccagesannsannnanscuecionssecscueasanaas 24 23-5. Motor TOSt sssicisscas iscsaiaasccivscsasasssntenssaincnssasasctvnin isesananscsavece aniasstensianecus say 25 2-3-6 Motion Stop Test . 2-3-7 Lamp Test. 2-3-8 LED Test... 2-3-9 Sound Test

2-4 Adjustments When Replacing Parts (Initialization)

DISASSEMBLY .........cccseeccceeeceteeeseseececeeseeeseseeeecessenesesaseeseseseeseseeeneesaeeeea 29

3-1. Removing the Monitor Assy (L), (R) 3-2 Disassembling the Upper Seat Assy from the Seat Base Assy

Page 6
  • INSTALLATION

Notes on installation

( DANGER: NEVER turn the power to the machine ON until installation has been

completed.

DANGER: In order to avoid injury or damage to the machine due to mis-operation, ensure that the voltage of the mains in supply is 220-240volt AC. Also, in order to prevent possible electric shocks, be sure that the machine is connected to the mains in supply with a securely connected earthed plug. )

When installing the machine, in order to maintain customer safety, be sure to attach the supplied rear fence and safety warning mats. In order to prevent customer injury when the machine is being played, make sure that the space between the side of the machine and a wall or other machine is at least 30cm. In order that the PCB rack or power supply can be removed for service, make sure that the rear of the machine is separated from a wall or other] machine by a distance of at least 50cm. )

Wall

30 cm or more 30 cm or more

[NOTE]

The shipping brackets that are removed during installation will be required ‘Wall

50cm or more

to be refitted for moving, shipping, and for maintenance when the drive castor is worn. They should be stored safely and not lost or thrown away.

Page 7

1-1 Installing the Sign Assembly

For your convenience, the sign assembly has already been fitted to the tower unit.

NOTE: The weight of the Sign Assembly (not including the sign board) is 32kg. The centre of gravity of the Sign Assembly is to the front , making it unstable, and as assembly involves lifting the Sign Assembly above head height, at least two people should be used to install the Sign Assembly.
  • Remove the two security screws (M5x12), and remove the harness cover.
  • Make sure that there are no wires or connectors on top of the main tower assy. If there is, drop them in to the tower.
  • { NOTE: The Sign Assembly is unstable. Ensure that one person maintains the balance of the sign assembly during installation.
  • Place the Sign Assembly on top of the tower, making sure that the Sign Assembly is forward of the tab at the top rear of the tower. Centre the Sign Assembly left to right and push the assembly back until the base board engages in to the tab.
  • Using the four hex head bolts (M10x30) and washers supplied, secure the Sign Assembly to the main tower assembly.
  • Feed the harness through from the tower assembly and connect the connectors. Refit the harness cover using the two security screws (M5x12) removed in step 1.

Security screw (MS x 12) Harness cover

Hexagonal bolt (M10 x 30)

Washer

Sign Assy las

Main tower Assy i Connector

Sign base board

Figure 7.

Page 8

1-2 Installing the Sign Boards (L), (R)

The overall height of the machine can be adjusted by altering the position at which the sign boards are fitted.

Normal Height (Total height: 2,200mm)

  • Bring the Sign Boards (L), (R) close to the fixing position, and connect the connectors.
  • Hang the Sign Boards (L) (R) on the side joints (L) (R).
  • Slide the Sign Boards (L) (R) to the back, and fasten to the cabinet using two security screws (M6x20).

Sign board (R)

Side joint (R)

\Security screw (M6x20)

Lower Height (Total height: 2,140mm) Connector

  • Remove the two hex head screws (M6x20), and remove the side joints (L) (R).
  • Turn the side joint top to bottom, and refit the side joint using the lower two of the three fixing holes.

Side joint (R)

Hexagonal bolts (M6 x 16)

Page 9

1-3 Connecting the Seat Assemblies to the Tower Assembly

  • Insert the seat assembly from the side of the tower unit so that the front legs of the tower unit are underneath the seat assembly.
  • Remove the four security screws (M5x12) from the bottom front of the tower unit, and remove the lower front cover (F). Temporarily fasten the seat unit with two hex head bolts (M10x25), flat washers and safety washers. (Do not tighten)
  • Remove the four security screws (M5x12) from the bottom rear of the tower unit, and remove the lower rear cover (S). Temporarily fasten the ride unit with four hex head bolts (M10x25), flat washers and security washers.
  • Tighten all of the hex head bolts (M10x25).
  • Connect the connectors between the seat assembly and tower unit.
  • Connect the other seat assembly in the same way.
  • Replace the front and rear covers (F), (S) taking care not to trap or pinch any wiring.

(Magnified view: (pg 5)

Washer

Hex head bolt (M10 x 25) |

Stand cover (S) ‘At

Security screw (M5 x 12) 7]

Washer *-

Hex head bolt (M10 x 25)

Safety Rubber

Seat assy.

[NOTE]: When connecting the seat asseblies to the tower unit take care not to trap any wires.

Page 10
  • _ Insert the front rubber brackets (L), (R) of the tower unit in the side panel of the seat assembly, and fasten them with two security screws (M5x16) and two No6X¥2" pozi flange head screws.

A

/NoSx’A" Pozi flange head screw

Rubber bracket (L) Seat Assy

\\__ Security screw (M5 x16)

  • Remove the five security screws (M5x16) from the tower side support.
  • Fit the rear safety rubbers to the tower unit with the retaining bracket and the five security screws (M5x16) previously removed from the tower side support.

Retaining bracket

Seat Assy

Security screws (M5x16)

  • Place the left, centre, and right safety warning mats in their correct positions.
  • When the machine is in its final location, lower the level adjusters (17 adjusters) with a spanner so that all castors are raised from the floor.
  • Tighten the lock nuts with a spanner to ensure that the level adjusters not move.

Level adjuster Lock nut

Page 11

1-4 Removing the Shipping Brackets

NOTE: Store the removed shipping brackets in a safe place as they must be refitted when replacing the drive castor, when shipping, or when moving the machine,
  • Remove two hex head bolts (M8x20) from each rear shipping bracket, and remove the brackets. Retain the four hex head bolts (M8x20) that were used to fit the shipping bracket for future use.
  • Slacken two security screws (M10x30), and remove two heax head bolts (M8x20) from each front shipping bracket, and remove the brackets. Re-tighten the four security screws (M10x30).

\ Seat Assy

Hex head bolts (M8 x 20)

Hex head bolts (M8 x 20)

Front shipping brkt

Security screws (M10 x 30)

Rear shipping brkt

Seat base assembly

Page 12

After removing the shipping brackets, install the supplied safety rubber skirt (D) and skirt stay (F) to the upper base assembly as described below.

NOTE: The safety rubber skirt is to prevent hands or feet being trapped by the moving parts. Be sure to install the safety rubber skirts.
  • The safety rubber is installed on the outside of each seat assembly. i.e.on the left of the left hand seat and on the right of the right hand seat.

Left side (L) Right side (R ight side (R)

  • _ Install the safety rubber and skirt stay using three security screws (M5x20).
NOTE: Ensure that the gap between the bottom of the skirt and the cover plate is no greater than 1.5mm.

Upper base Assy

. Upper base Assy Side plate

Seat base Assy

T . =— gkirt Stay (F) ———— os Skirt (D)

& 8 Security screw (M10 x 30)

ecurity screw (M5 x 20)

Page 13

1-5 Installing the Guard Fence

  • Fasten the guard fence with two retaining plates and security screws (M8x20), flat washers, and security washers.
  • _ Fit the extension brackets (R),(L) to the seat base using six security screws (M8x20), spring washers, and flat washers on each. Ensure that the angles of the extension bracket match the angles of the extensions fitted to the seat bed.

Seat bed

Extension brkt

Security screw (M8x20) Flat washer Guard fence

  • Retaining plate g \ Safety washer Security screw (M8x20)
Page 14

1-6 Applying the Number Stickers

Apply the racing number stickers to the seats and sign boards as shown below.

Racing number for sign

Racing number for seat

Seatback Sign board (L), (R)

The team colours and car numbers should match those shown in the following table.

TEAM COLOUR ||RED 25 |BLUE 3 | YELLOW 17 |GREEN 11 Ic

Team Colour Red Blue Yellow Green

Car Number 25 3 7 in

[NOTE]: Ensure that the numbers on the screen match the sticker numbers. The "TEAM COLOURS" can be checked in the "Test Mode" - "Setting the Game Options". (page 14)

Page 15

1-7 Linking Two or More Machines.

Up to four machines (8 seats) can be linked together. The machines should be linked as described below.

NOTE: Each machine can draw up to 8 amps. Make sure that the power supply is adequate.
  • Ensure that the power is “OFF”. Connector cover
  • Loosen the two screws (M4x10) on the back of the tower assy, and remove the connector cover. » screw (M4 x 10)
3)Set the link switches to “ON” , “EXT”,.itch

and “ON”. (See Diag.) Link: switches

  • Use the supplied link cable and connect the machines between “IN” and “OUT” sockets (See Diag.)

[Examples of Linked Machines]

a)2Machines9096
(4 Seats)INOUTINOUT
b)3 MachinesSo©6oOOo9
(6 Seats)INQUTINOUTINOUT
c)4Machines660Oo©66oO
(8 Seats)INOUTINOUTINOUTINOUT
  • Turn the power to each machine “ON”, and set the PCB ID using the test mode. (Refer to} “Setting the Game Options’).
Note: Settings other than those described will cause the machine to operate incorrectly.
Page 16

1-7-1 Setting the Link Switches

The link switches are used to set the connection between seats and machines.

1). Setting only one machine (2 seats)

Set the link switches to “ON”, “INT”, and “ON”. 2 ® ofam alo

Note: Do not use a link cable. ° be oo

@o P2 Io

  • Setting two or more machines. ° °

Set the link switches to “ON”, “EXT”, and “ON”. °

°

  • Install the connector cover using §= —————-—____ screw (M4 x 10) the two screws (M4x10). id

The link procedure is now complete. °

\ Link cable

  • Setting for faulty PCB. If the game PCB of only one side is faulty, set the link on that side to “OFF”

[Example of setting for faulty left side]

=

Seat with problem

Page 17

2 ADJUSTMENTS

2-1 Turning on the Power

After the machine has been correctley installed, turn ON the power. The Power switch is located next to the IEC power inlet socket on the rear of the tower unit

2-2 Adjustment Switches

The adjustment switches are located inside the coin door.

1. Service Switch Press this switch to obtain game credits without incrementing the play meters.

Test Switch Slide this switch “ON” to enter test mode. Test mode allows game te e changing of game settings. (Refer to section 2-3 “Test Mode’

COIN COUNTER

(6)

[e)

LEFT PLAYER RIGHT PLAYER

TEST SERVICE TEST SERVICE

Page 18

2-3 Test Mode

  • Open the coin door and slide the test switch “ON”. The “Menu Screen” will be displayed on the monitor.
  • Select the test required by moving the shift lever up or down. The colour of the selected test will change.
  • Enter the selected test by stepping on the accelerator. Select “EXIT” to return to the “Menu Screen” (step on the accelerator when using the monitor test screen).
  • After testing is completed, ensure that the test switch is returned to the “OFF” position to return to game mode.

The Test Switch must always be in the “OFF” position for normal game mode.

(— >) MENU

COIN OPTIONS---t--(1) Sets the price of play} (See2-3-1)
GAME OPTIONS-----(2) Sets the game optiong.(See 2-3-2)

VO TEST (3), jing the switches and motor. (See 2-3-3)

MONITOR TEST-----(4) Used for adjusting the monitor.
SOUND TESTs-q--(5)isting the speaker volume.

See (See 2-3-9)

ADS DATA---+--(6) Displays the accumulated game data.

OTHERS (7) Used for testing the PC boards and for initializing all of the settings.

GAS: ENTER _ SHIFT: CHOOSE

Page 19

2-3-1 Coin Options

Select item (1) “COIN OPTIONS” on the menu screen, to set the game cost and related settings.

Use the shift lever to select the required item then step on the accelerator.

Use the shift lever to change the settings then step on the accelerator to store the new values.

Select “EXIT” to return to the menu screen. ( \ COIN OPTIONS [DEFAULT IN GREEN]

GAME COST 1 COIN 1 CREDIT (a)

COIN1 MECH VALUE 1 COIN COUNT AS1COIN _.....u...

COIN MECH 2 VALUE 1 COIN COUNT AS1 COIN _.......

BONUS FOR QUANTITY BUY IN NONE ese

FREE PLAY OFF

EXIT

\ GAS: ENTER SHIFT: CHOOSE

Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Coin Options on the screen are set as shown in the following table.

TEM CONTENTS FACTORY SET

(a) Game CostCoins required for 1 credit - - - - - - settable 1-91
(b) Coin 1 Mech ValueNumber of pulses on meter per coin - - - - - - settable 1 - 91
(c) Coin 2 Mech ValueNumber of pulses on meter per coin - - - - - - settable 1-91
(d) Bonus CoinExtra coin pulse at specified coins inNONE
(e) Free PlayGame started by pressing accelerator - - - - - - Yes/NoNO
Page 20

2-3-2. Game Options

a.Select item (2)“GAME(Game OPTIONS [DEFAULT IN GREEN] >

OPTIONS’ on the

menu screen to set thePCBIDNUMBERreessssses

game options. TEAM COLOUR BLUE 3 .......... b. Use the shift lever to

select the requiredRACE CLASSBEG EXP PRO_..........

item then step on the

accelerator.DIFFICULTYBBB
c.Use the shift lever toLAPS [LINK]834ree
change the settingsLAPS[SOLO]334aes

then step on the

accelerator to store theSPEED DISPLAYKM/Hones

new values.

SOUND IN ATTRACTONeeeceeeees

d. Select “EXIT” to return to the menu screen. EXIT

Note: Race Class (c) must\ GAS: ENTERShit CHOOSE}

be set first before changing items (d), (e), or ().

NOTES

The rank (level of difficulty) and number of laps must be set the same on all positions that are linked.

The PCB number of the seat furthest left (when facing the front of the machine) should be set to 1, and the other seats set to 2, 3, 4 and so on in order from left to right. The PCB number of the farthest right position should equal the number of positions linked.

Settings other than those described will cause the machine to operate incorrectly.

Page 21

TEM DESCRIPTION FACTORY SET

  • PCB Number The PCB number should be set so that none of the linked positions have the same number
  • Team Colour RED 25 or 26

BLUE sor4

YELLOW 170r18

GREEN 11 or 12

  • When more than three sets (6 seats) are linked, different race numbers should be used for the same team colours.
(c) RaceBEG(d) Game difficulty level (time)A (long) to D (short)B

Class

(e) Number of laps (linked game)3 to 63
(f) Number of laps (solo play)3to63
EXP(d) Game difficulty level (time)A (long) to D (short)B
(e) Number of laps (linked game)3to63
(f) Number of laps (solo play)3to63
PRO | (d) Game difficulty level (time)A (long) to D (short)B
(e) Number of laps (linked game)3t064
(f) Number of laps (solo play)3to64
(g) Speedo UnitsKM/H/MPHMPH
(h) Attract SoundON / OFFON
Page 22

2-3-3 W/O Test

  • Select item (3) “I/O TEST” on the menu screen.
  • Use the shift lever to select the required item then step on the accelerator.

(— >) VO TEST

DIP 212345678aaa ..(a) Option Switch (CPU-PCB Sw2)
312345678asa ..(b) Option Switch (CPU-PCB Sw1)
LINKON2COUNT 0....... ..(c) Link Check

SWITCH (d) Switch Test MOTOR (e) Motor Test LAMP (f) Lamp Test LED (g) LED Test EXIT

GAS: ENTER SHIFT: CHOOSE NX /

  • Displays the state of the option switch, SW2, on the game PC board (CPU-PCB).
  • Displays the state of the option switch, SW3, on the game PC board (CPU-PVB). For both items (a) and (b), the switch is ON when the numbers are shown in red.
  • Displays the number of positions linked. If there is a link error, “ERROR” is displayed. The numbers to the right of “COUNT”, display the number of link errors detected during the I/O test.
  • Tests the switches. | (See 2-3-4.)
  • Tests the motors. | (See 2-3-5.)
  • Tests the lamps. | (See 2-3-7.)
  • Tests the LEDs. | (See 2-3-8.)
Page 23

2-3-4 Switch Test

The following screen is displayed when “SWITCH” is selected on the I/O screen.

VO TEST

DIP 2 12345678 3 12345678

LINK ON 2 COUNT 0

SWITCH

(a) Accelerator ..GAS:*0000COIN1:OFF.|.

..(e) Coin 1 switch

(b) BrakeBRAKE *0000COIN2:OFFf) Coin 2 switch
(c) SteeringSTEER *0000SERVICE: OFFg) Service switch
(d) ShiftSHIFTCENTREVIEW:OFF |]......(h) View change switch

TO EXIT, STEP ON GAS AND SHIFT UP N w,

BS When the accelerator is stepped on, the number increases in the + direction. = When the brake is stepped on, the number increases in the + direction. io When the steering wheel is turned to the right, the number increases in the + direction, and when it is turned to the left, the increases in the - direction. When items (a), (b), and (c) are in their middle position, “O000” is displayed. (It is normal for the last digit to change.) Just before the steering wheel is as far as it will go, or just before stepping on the accelerator or brake as far as they will go, “Ok” will be displayed to the right of the number if everything is correct.

  • Displays the position of the shift lever (CENTRE, UP, DOWN) and the state of the switches.

When the shift lever is pressed forward, switch 1 goes “ON” and “DOWN” is displayed, and when it is pulled back, switch 2 goes “ON” and “UP” is displayed.

  • When coin 1 switch is operated, “ON” is displayed.
  • Unused.
  • Goes “ON” when the service switch inside the coin door is pressed.
  • Goes “ON” when the view change button is pressed

To return to the menu screen, move the shift lever up and step on the accelerator.

Page ig

Page 24

2-3-5 Motor Test

The following screen is displayed when “MOTOR?” is selected on the I/O screen.

VO TEST

DIP 2 12345678

LINKON 2 COUNT O

SWITCH MOTOR BASE MOTOR OFF senseedecasenhe (a) Seat motor test STEERING OFF TORQUE 00 _.......]........ (b) Steering motor test EXIT

GAS: TURN SHIFT: CHOOSE ~\

3 12345678

(a) Tests the seat roller motor. When “BASE MOTOR?’ is selected and the accelerator is pressed the test is “ON” and the motor starts to operate. Pressing the accelerator again turns the test “OFF” and the motor stops.

Tests the steering feedback motor. When “STEERING? is selected and the accelerator is pressed the test is “ON” and the motor will start and turn the steering wheel left and right. When performing this test, ensure that test (a) “BASE MOTOR’ is also “ON”. Pressing the accelerator turns the test “OFF” and the motor will stop.

Select “EXIT” to return to the I/O test screen.

Note: Performing the steering motor test can be dangerous, sit on the seat properly, and take hands off the steering wheel.

2-3-6 Motion Stop Test

The Stop Motion Switches will illuminate as soon as the test switch is turned ON.

To test the motion stop switches enter motor test (Refer to section 2-3-5, “Motor Test”.) and select Base Motor ON.

Each time a stop motion switch is pressed, the motor will stop and restart when the switch is released.

NOTE: If the switch is pressed during game play, the seat motion will stop and remain off for the duration of that game.

Page ig

Page 25

2-3-7. Lamp Test

The following screen is displayed when “LAMP” is selected on the I/O screen.

(10 TEST >)

DIP 2 12345678 3 12345678

LINKON 2 COUNT 0

LAMP TOP LAMP SIGNAL LAMP RED SIGNAL LAMP GREEN EXIT

GAS: LIGHT SHIFT: CHOOSE N /

( ( (

  • Tests the top lamp.
  • Tests the red signal lamp.
  • Tests the green signal lamp.

Select “EXIT” to return to the I/O test screen.

2-3-8 LED Test (a) (b) (c)

The following screen appears when “LED” is selected on the I/O test screen.

( VO TEST

DIP 2 12345678 3 12345678

LINKON 2

GAS: LIGHT COUNT 0

EXIT

SHIFT: CHOOSE ~

  • Tests the finish position LED.

Select “EXIT” to return to the I/O test screen.

Page 26

2-3-9 Sound Test

To adjust the sound volume, select “SOUND TEST” in the menu screen. The following screen will be displayed.

XQ ~ SOUND TEST [DEFAULT IN GREEN]

VOLUME [MAX 63] LEFT RIGHT

  • Left speaker volume © ........fee 40 40

SONG 40

EXIT

GAS: ENTER SHIFT: CHOOSE OS ) .-|.. (b) Right speaker volume

Select (a) or (b) by using the shift lever, the characters will blink in red, when the accelerator is pressed the numbers will start to blink. Moving the shift lever up will increase the number, moving the shift lever down will decrease the number.

The volume can be adjusted in 64 steps, with 00 the lowest and 63 the loudest. The factory setting is “40”

Select “EXIT” to return to the menu screen

Page 27

2-4 Adjustments When Replacing Parts (Initialization)

The following adjustments should always be performed after initial installation and after replacing the game PC board, ROM, Steering Assy, Pedal Assy, or Control Pots. The game will not operate correctly if these adjustments are not made.

  • Ensure that accelerator and brake pedals are fully returned.
  • Place the steering wheel to it’s centre position and remove hands from the wheel (The steering wheel does not return to centre by itself.)
  • Slide the test switch “ON” while pressing the service switch. The following screen will be displayed on the monitor.

~) ADJUST MODE

BASE BIAS VALUE

STEER:********0000
GAS:**™*0000
BRAKE:*******0000

ADJUST WHILE PRESSING SERVICE SWITCH. TO EXIT, TURN OFF TEST SWITCH. Ne yy,

  • Press the service switch to reset all values to 0000
  • Fully depress and release the accelerator, then the brake, then turn the steering wheel fully left and right.
  • Slide the test switch "OFF" to return to normal game mode.
  • If the above initialization does not perform correctly, repeat two or three times.
Page 28
  • DISASSEMBLY
NOTE: The proper number of people (listed in each item) should be used when disassembling.

This machine may be disassembled further than as shipped for shipping and moving. The following is a general method of disassembly.

(NoTE: Parts may be damaged if placed upside down or on their side when removed)

Sign board (L) Tower unit

Sign board (R)

Seat assemblies

Page 29

3-1.Removing the Monitor Assy (L), (R)

DANGER: There are areas within the monitor that have high temperature and very high voltage even after the power has been removed. Extreme care must be taken to avoid burns or electric shock.
DANGER: The monitor weighs approx 60kg, at least two people should be used to remove the monitors.

Ensure that the power is turned OFF before removing the monitors. Remove the back door from the monitor. Disconnect the six way video connector and three way power connector. Remove the hex head screw (M4x10) retaining the earth terminal. Remove the six security screws (M5x12) on the rear of the main tower assy, and remove the rear cover (U). Remove the wiring leading from the main tower to the monitor assy. Remove the four security screws (M5x12) on the front of the main tower assy, and remove the acrylic fastener bar and acrylic sheet. The monitor is fastened on the side and bottom to the main tower assy. Remove the following bolts: Side: Five hex head bolts (M8x45), flat and safety washers. Bottom: Two hex head bolts (M8x25), flat and safety washers.

WARNING: _ If the seat assemblies are not fitted to the tower and only one monitor is being removed, the tower assembly will be unstable, so remove both monitor assemblies.

Security Screw (M5x12) Acrylic fastener bar Rear cover (U)

Page 30

3-2 Disassembling the Upper Seat Assy from the Seat Base Assy

WARNING: The weight of the upper seat assembly is approx. 120kg. Foot position is poor and the assembly heavy, so at least five people should be used for disassembly
WARNING: This work involves moving the seat assembly from left to right in order to remove screws. Take care not to trap or injure the other person when performing this work.
  • Remove the rear covers (L), (R).

Removing the Rear Cover (L)

  • Remove the rear guard fence.
  • Turn the steering wheel all the way to the right, and move the cabinet by hand so that the rear cover (L) is easier to remove.
  • Remove the security screws (M5x20), and remove the edge guards and rubber skirts.
  • Remove the nine security screws (M5x12) and two security screws (M8x20), then remove the rear cover (L)

Removing the Rear Cover (R)

  • Turn the steering wheel all the way to the left and move the cabinet to the left by hand so that the rear cover (R) is easier to remove. Rear cover (R)
  • Remove the rear cover (R) in the same way as the rear cover (L) as above.

Security screw (M5 x 20): /

Edge guard Rear cover (L)

Security screw(M8 x 20) Rubber skirt Security screw (M5 x 12)

Page 31
  • Remove six security screws (M5x20) and remove the rear cover.
  • Remove two security screws (M5x20), four security screws (M5x40), and remove the top cover plate.
  • Loosen the hex head screws on the top joint section, slide the sleeve along the shaft and disconnect the joint.
  • Disconnect the bottom joint section as follows:
  • Remove six security screws (M6x25), and remove the joint cover.
  • Remove two hex head bolts (M10x30).
  • Slide the upper seat assembly a little to the back, then lift and separate it from the seat base assembly.

Joint section (top)

security screw (M5x40

Top cover

Security screw (M5 x 20)

Upper seat assy

Hex head screw (M10 x 30) << Seat base assy

Joint section (bottom