CATHODE RAY TOMES

Space Duel TM-181 1st Printing

Space Duel (version 2) (Atari, 1980) · Technical Manual · 64 pages · 55 sections · original scan

Page 1

TM-181 4st printing

Page 2

GAME SERIAL NUMBER LOCATION Your game's serial number is stamped on a label on the outside of the game. The same number is also on the chassis of the video display, power supply, Regulator/Audio || PCB, and the Game PCB. Please mention this number when calling your distributor for service.

GAME IDENTIFICATION, SERIAL NUMBER LABEL

GAME PCB

GAME IDENTIFICATION, SERIAL NUMBER LABEL

REGULATOR/AUDIO I! PCB.

GAME PCB POWER SUPPLY

REGULATOR/AUDIO II PCB

GAME IDENTIFICATION, SERIAL NUMBER LABEL

Page 3

*” Operation, Maintenance

and Service Manual

Complete with Illustrated Parts Lists

Copyright © 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher

The Space Duel™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the new Copyright Act of 1976.

This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.

In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year

Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI INC. 1265 Borregas Avenue PO. Box 427 Sunnyvale, California 94086

Lithographed in the U.S.A aL

Page 4

to licensed communications services is not permitted by the FCC (Federal Communications Commission) lf you suspect interference from an ATARI game at your location, check the following: @ All grounds (green wires) in the game are properly connected as shown in the game wiring diagram, and @ The game’s power cord is properly plugged into a grounded 3-wire outlet. If you are unable to solve the interference problem, please contact: Atari Customer Service (800) 526-3849 or (800) 538-1611

Page 5

Notice Regarding Non-ATARI Parts

WARNING

Use of non-ATARI parts or modifications of your ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

The warranty printed on the inside back cover of this manual may be voided, if you do any of the following:

  • you substitute non-ATARI parts in your coin-operated game, or
  • you modify or alter any circuits in your ATARI game by using kits or parts not supplied by ATARI.

Not only may the use of any non-ATARI parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 6

Table of Contents

1 Set-Up Procedures

Opening the Cocktail Cabinet Game Inspection ......... Game Installation. .

  • Installation Requirements
  • Voltage Selection .... Cocktail Table Legs . Switch Locations
  • On/Off Switch
  • Cocktail Table Interlock Switch
  • Utility Switches ...........
  • Option Switches ... G. Self-Test Procedure ..... H. Option Switch Settings |. Game Play......... . Attract Mode ... . Ready-to-Play Mode. . PlayMode ...... . High Score Mode pom>

mm

Pons

2 Troubleshooting

Comments on Troubleshooting... Self-Test Procedure .......... Glossary of Schematic Signal Descriptions 9ODP

3 Illustrated Maintenance, Repair and Parts Maintenance, repair and parts lists begin on page........... New Features... 2.2... oc eee ec ee ene ee eee

Introduction 6.0... cee ec cence eet eenne

Page 7

Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4

Figure 1-5 Figure 1-6 Figure 2-1 Figure 2-2

Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4

Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8

Figure 3-9 List of Illustrations

Game Overview . 0.6... cece cette teens 1-2 Adjusting the Table Legs Game Switch Locations .. 7 Operator Information Display ............ 0.000. e eee eee eee 1-8

Self-Test Procedure ....... 6.6. occ cee cece eee Ready to Play Screen. Self-Test Screen if Test Passes Self-Test Screen 1

Self-Test Screen 2.0.0.0... cece cece eee eee 23 Self-Test Screen 3. Self-Test Screen 4. Self-Test Screen 5. . . Self-Test Screens During Signature Analysis ............. 25

Illustrated Maintenance, Repair and Parts: Cabinet-Mounted Assemblies . The Control Panel ........ Control Panel Assemblies...... Speaker, Fluorescent Tube and Fan

Video Display ....... 00... ccc ccc cece cece cet e eet n eee eeenes Vertical-Mounted Coin Door . . Printed-Circuit Board Removal Space Duel™ PCB Assembly ...........000 0000 eee e eee eee

Regulator/Audio II PCB Assembly ........2....0 000 e eee eee 3-22 Figure 3-10 Color X-Y Power Supply Assemblies. ..........6.0 0000s eee eee 3-24

Table 1-1 Table 1-2 Table 1-3 Table 1-4 Game Options ........ 0... ce cee eee eee Game Price Options Special Options .. . Space Duel Targets

Page 8

Space Duel

vi \™

NOTE If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Service only

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) ee From California, Alaska, or Hawaii (408) 745-2900 = Service from anywhere in the area shown in white @ ‘ioll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey @ (201) 469-5993

From anywhere else in this area toll-free (800) 526-3849

EUROPE Service only

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

@ 0062-52155

Page 9

Set-Up Procedures

How to Use This Manual

This manual, written for game operators and service technicians, describes the Space Duel™ game. The manual contains information about a// Space Duel cabinets. Whenever information is unique to the Upright cabinet, this symbol appears:

Whenever information is unique to the Cocktail game cabinet, this symbol appears: @l

Chapter One inciudes new features, game set-up, self-test procedures, option switches and game play.

Chapter Two details troubleshooting procedures.

Chapter Three contains maintenance, repair and parts information. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the game cabinets. Suppose you need to find information about a specific part of a cabinet. These figures list other places in the manual to find information about that part.

A. New Features

The Space Duel™ game has three new features. Even if you are familiar with ATARI® games, you should note these important differences. The new features are: @ Game Play. Players may choose four different game versions. A single player may play fighters or space stations. Two players, playing at the same time, may play fighters or space stations. Players may compete against the game, or against each other and the game. There are 18 different waves, each offering a variety of targets (see Section |, Game Play). @ Game Cabinet. The Space Duel Upright cabinet is no wider than any other Atari game cabinet, yet has enough space for two players to play side by side. The cabinet has four speakers, which provide exceptional audio. @ Vertical-Mounted Coin Door. This new door has two separately keyed doors. One door provides full access for servicing the coin acceptors and other electrical parts. The other door provides access to the cash. In addition, the lockout coil receives its power from the game PCB. If the PCB is not functioning properly, coins will be rejected. These new features, as well as all other major parts in the game, are illustrated in Figure 1-1. Throughout this manual, wherever one of these new features is mentioned, you wil! see this symbol: -~S

Chapter

Page 10

Space Duei™

ATTRACTION PANEL

COLOR X-Y VIDEO DISPLAY See Figure 3-5

CONTROL PANEL See Figur 2 3-2, 3-3

COIN DOOR See Figure 3-6

UTILITY PANEL See Figure 1-3

1-2 SPEAKERS AND FLUORESCENT TUBE See Figure 3-4

@

\ ACCESS PANEL

~®

GAME PCB See Figures 3-7 3-8

REGULATORI AUDIO Il PCB See Figures 3-7, 3-9

POWER CORD

()

POWER SUPPLY See Figure 3-10

CASTER POWER ON/OFF SWITCH

Figure 1-1 Upright Game Overview

Page 11

\™ Space Duel

COLOR X-Y VIDEO DISPLAY

See Figure 3-5 S

GAME PCB See Figures 3-7, 3-8

INTERLOCK SWITCH

LOCK CONTROL PANEL a See Figures 3-2, 3-3

FAN ACCESS PANEL

REGULATORI COIN DOOR AUDIO II PCB See Figure 3-6 See Figures 3-7, 3-9

ADJUSTABLE LEG See Figure 1-2 POWER ON/OFF SWITCH

SELECT SWITCH SPEAKER

START SWITCH

POWER SUPPLY now=neete COINCOUNTER LATCH ‘See Figure 3-10

Figure 1-1, continued Cocktail Game Overview

¢

WARNING: B. Opening the Connect this game only to a grounded al Cocktail abinet

SHOCK HAZARD . Cc :

3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed 1. Opening the Table Top electrician to install a grounded outlet. : Players may receive an electric shock if @ To open the game cabinet, unlock and open the coin door. Reach inside and open the luggagestyle latch located on the cabinet wall to your right. Next, unlock the lock at one end of the To prevent electric shock, disconnect game, located immediately below the table top. power supply cord before opening service (see Figure 1-1). panel or servicing the game. this game is not properly grounded!

@ Carefully lift the table top until the support arm locks into place. Do not jam the table top at the end of its upward swing.

1-3

Page 12
  • Access Panel @ To open the access panel, lift out the steel security bar that secures the panel to the cabinet wail. @ The access panel near the bottom of the cabinet will then come out.
  • Closing the Table Top @ To close the cabinet, stand opposite the hinged end of the cabinet and grasp the table top with your right hand. @ With your left hand, press the button at the middle of the support arm and push the button out toward the left. @ Gently lower the table top to the closed position. @ Lock the key lock. Then reach inside the coin door and close the luggage-style latch. Lock the coin door.

C. Game Inspection

Please inspect your game carefully to insure that it was delivered to you in good condition.

NOTE Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Remove the screws that were used as extra security to seal the access panel (for Upright Space Duel). Unlock and open this panel, the coin door, and the Cocktail table top. Inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCBs are firmly seated in their sockets. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening (Upright only).

1-4

WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the video display with your hands or with metal objects held in your hands!

@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers on the game PCB, Regulator/Audio || PCB, power supply and video display are all identical. A drawing of the serialnumbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and video display for secure mounting.

D. Game Installation

  • Installation Requirements

Power 200 watts maximum Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Upright Cabinet 64 x 80% cm (25% x 31%2 in.) 182 cm (71% in.)

Cocktail Cabinet Gil

71% x 85 cm (28% x 33% in.) 682 to 104 cm (27 to 41 in.) Space Required Game Height

Space Required Game Height

  • Voltage Selection The power supply used in this game operates on the line voltage of almost any country in the world. The power supply may come with either one, two or three colored voltage selection plugs.

Before plugging in your game, check your power supply. If the supply doesn’t have voltage selection Plugs and a connector at J3 (see Figure 3-10), then the game operates on any voltage from 105 to 135 VAC. If the supply has the colored voltage selection plugs, make sure that the voltage selection plug on the power supply is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3-10.

Page 13
NOTE To ensure cabinet strength, you must use

E. Cocktail Table Legs

@ | | | two screws when attaching each table This cocktail-table game is designed for four ad- leg. Using only one screw may result in justable heights—68¥2, 74, 80 or 104 cm (27, 29%, damage to the cabinet wall when you 31% or 41 inches). To adjust the table height, refer to move the cabinet across the floor. Figure 1-2.

  • Remove or empty the coin box. Loose coins may slide out of the box and into the game cabinet.
  • Lay table on end as shown.
  • Remove the two Allen-head screws on Alin. each leg. Grasp the legs and slide them into the desired position. Then replace the screws. 31% in.

29% in.

SHIPPING POSITION (27 in.)

iy

USE TWO SCREWS WHEN ATTACHING EACH TABLE LEG!

Figure 1-2 Adjusting the Table Legs

1-5

Page 14

F. Switch Locations

  • On/Off Switch The Upright game on/off switch is located on the back of the cabinet, lower left side. The Cocktail game onloff switch is located on the bottom of the cabinet, below the key lock (see Figure 1-3).
  • Cocktail Table Interlock Switch &!

To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed. It is located under the table top (see Figure 1-3). This switch removes all AC line power from the game circuitry when the panel is opened. Check for proper operation of the interlock switch by performing the following steps: @ Close the table top. @ Plug the AC line power cord into an AC outlet. @ Set the power on/off switch to the “on” position. Within 30 seconds the screen should display a picture.

UTILITY PANEL

VOLUME CONTROL (To increase, turn clockwise)

SELF-TEST SWITCH

UTILITY COIN SWITCH COIN COUNTER (See Figure 1-3, cont'd.) @ Slowly open the table top. The video picture should disappear when the top is lifted about 2¥2 cm (1 inch). Close and lock the table top. @ Ifthe results of the preceding steps are satisfactory, the interlock switch is operating properly. If the video display doesn't go off as described, check to see if the interlock switch is broken from its mounting or stuck in the “on” position.

  • Utility Switches The utility panel includes the volume control, selftest, coin switch, (and for the Upright game, coin counter). The Cocktail coin counter is inside the upper coin door. The coin switch is used to coin the game without tripping the coin counter. These switches are located inside the upper coin door (see Figure 1-3).
  • Option Switches Option switches are located on the game PCB: @ Game play options are at PCB location D4. @ Game price options are at PCB location B4. @ Special options are at PCB location P10/11.

SAFETY INTERLOCK SWITCH

OPTION SWITCHES

SWITCH COVER

POWER ON/OFF SWITCH (Reach under game SLAM SWITCH to activate switch)

Figure 1-3 Cocktail Game Switch Locations

1-6

Page 15

SLAM SWITCH

OPTION SWITCHES UTILITY PANEL

UTILITY COIN SWITCH r Prot @ S a1

COIN COUNTER

SELF-TEST SWITCH SWITCH AT B4 (Game Price) VOLUME CONTROL (To increase, turn clockwise) POWER ON/OFF SWITCH SWITCH AT D4 (Game Play)

SWITCH AT P10/11 (Special Options)

Figure 1-3, continued Upright Game Switch Locations

1-7

Page 16

Space Due|™

G. Self-Test Procedure

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. We suggest you run the self-test procedure when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure.

Wait at least 10 seconds after playing a game before entering self-test. Otherwise, the high-score table will be erased and the EAROM may get damaged. All credits will be cancelled when you enter self-test. All scores, except the top score, will be reset to 5,000.

Refer to Figure 1-3 for the location of the self-test switch and option switches. To run the self-test, set the self-test switch to on . The screen will show the Operator Information Display (see Figure 1-4). To continue, 1) press RESET on the PCB, or 2) turn the power off and on again, or 3) follow the steps outlined in Figure 1-5. Use Figure 1-5 to check test results.

The complete self-test procedure is explained in Chapter 2, Troubleshooting. \f any part of the test described in Figure 1-5 fails, refer to Chapter 2.

The Operator Information Display shows game statistics and option switch settings. In this mode you may also“erase game scores and times. To enter this mode, set the self-test switch to on.

Look at the biock of zeroes and ones at the top of the screen. If these numbers run together vertically, or do not line up horizontally, make adjustments to the X BIP and Y BIP potentiometers on the game PCB.

NO. OF CREDITS PER COIN FOR

UTILITY COIN SW.

SHIPS: PER GAME. LANGUAGE TOTAL ON TIME

(English) oT FIGHTER

Hl cockta,. —___¥¢

TIME GAME ————»_ PLAYED (Seconds) seen es FIGHTER — SPACE Cena NO. OF 5

GAMES AVG TIMES

AVERAGE 5 GAME TIME

Te erase game scores: GAME DIFFICULTY LEFT COIN MECH /

NO. OF CREDITS hi

FOR EACH PUSH OF > BONUS ADDER O

2 PLAYERS |

To erase game times: To enter Self-Test, press GAME SELECT until the message PUSH START AND SELECT FOR SELF-TEST appears on the screen. Then press both START and GAME SELECT. All credits will be cancelled when you go into self-test. To end the operator information display, set the self-test switch to off.

NO. OF CREDITS. FOR EACH PUSH OF RIGHT COIN MECH

BONUS ADDER

EE FIG. 1-5 Miseliaatsaauing ~———— For DEScAIPTION | XXXXXXXXK-A a BYYbE TIME GAME ON (Seconds)

ert “~————__ INSTRUCTION FOR SELF-TEST OR TO ERASE SCORES, TIMES AND SEL rot

PLAYER

eble 14464 Sey 3o°1b

l2 BS a (Ss

elb imal 2 dit

To erase game scores and times: 1, Push GAME SELECT until display 1. reads PUSH START AND SELECT TO CLEAR SCORES. . Press both START and SELECT. . The word ERASING flashes on the screen until the entire table is erased. Wait until the word ERASING disappears before going on with other tests. en eR Push GAME SELECT until display reads PRESS START AND SELECT TO CLEAR TIMES. . Press both START and SELECT. . The word ERASING flashes on the screen until the entire table is erased. Wait until the word ERASING disappears before going on with other tests.

  • Push GAME SELECT until dispiay reads PRESS START AND SELECT TO CLEAR TIMES AND SCORES. . Press both START AND SELECT. . The word ERASING flashes on the screen until the entire table is erased. Wait until the word ERASING disappears before going on with other tests. en

Figure 1-4 Operator Information Display

Page 17

Instruction Test Passes

  • Set the self-test switch to on (see Figure 1-3). Press START and GAME SELECT simultaneously.
  • Activate all contro! pane! switches: select, start, rotate left and right, fire, shields and thrust. Activate the coin switches.
  • Observe the white frame at the sides of the screen. After about 5 seconds, the screen displays the picture below’. No sounds are produced. The RAMs, ROMs and three other chips are tested. If the picture is different from the picture below, or there are sounds, refer to Chapter 2, Troubleshooting.

As the switch activates, you hear a beep, and 0 changes to 1 on the screen. If test fails, refer to Chapter 2, Troubleshooting.

Each frame corner should be within %-inch of each display bezel corner. If test fails, refer to Chapter 2, Troubleshooting.

*Only the white frame may appear for about 8 seconds if the EAROM is either new or contains bad data. To continue with selftest, press slam switch.

SWITCH SWITCH AT B4 TOCELE (Coin Modes) SWITCH TOGGLE 8 SWITCH AT D4 (Game Play)

FRAME

SWITCH TOGGLE 8

SWITCH AT P10/11 (Game Difficulty) SWITCH TOGGLE 1

SHIELDS (Player 1)

UTILITY COIN SWITCH (Player 1) i FIRE COCKTAIL (1) A (Player 1)

UPRIGHT (0) [ ata

ya FIRE GAME SELECT 1 | 7 xX (Player 2) S RIGHT COIN MECH ‘SHIELDS (Player 2)

LEFT COIN MECH ROTATE RIGHT

SLAM SELF-TEST ROTATE LEFT THRUST NOTUSED (Player 1)

THRUST (Player 1) ROTATE LEFT m

(Player 2) (Player 2) FOR TECHNICIANS ROTATE RIGHT ONLY (Player 2)

Figure 1-5 Self-Test Procedure

Page 18

Space Ouei™

H. Option Switch Settings

Tables 1-1, Game Options; 1-2, Game Price Options; and 1-3, Special Options detail the options and their settings. All options are preset at the factory and shown by the $ symbols. However, you may change the settings to suit your individual needs.

Table 1-1

To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches are accessible when the Space Duel™ game PCB is mounted in place. A special Demonstration Mode allows you to quickly view all 18 waves. To enter this mode, first set switch 3 at PCB location P10/11 to on. Next, set the game for free play by setting switch 7 at PCB location B4 to on and switch 8 to off. Press GAME SE- LECT to view the first wave. Each time you press GAME SELECT you will view the next wave in sequence. Ships must be alive on the screen for you to procede through the waves. Otherwise, you must wait until the ship reappears to go to the next wave.

Game Option Settings

When changing the options, verify proper results on the video display by performing the self-test. Note that changing some options during the attract mode may not cause an immediate change on the screen.

Settings of 8-Toggle Switch on Space Duel game PCB (at D4) 8 7 6 5 4 3 2 1 Option

On Off

Off Off

On On

Off On

On Off

On On

On Off On On

Off Off On 3 ships per game Ashipspergame $ 5 ships per game 6 ships per game Easy game difficulty* Normal game difficulty $ Medium game difficulty Hard game difficulty English $ German Spanish French

Bonus life granted at every: On 8,000 points Off 10,000 points $ Off 15,000 points On No bonus life

$Manutacturer's suggested settings *Easy—In the beginning of the first wave, 3 targets appear on the screen. Targets increase by one in each new wave. Normal—Space station action is the same as “Easy”. Fighter action has 4 targets in the beginning of the first wave. Targets increase by 2 in each new wave. Targets move faster and more targets enter. Megium and hard—In the beginning of the first wave, 4 targets appear on the screen. Targets increase by 2 in each new wave. As difficulty increases, targets move faster. and more targets enter.

Page 19

Table 1-2 Game Price Options The table below contains the switch settings for those options relating to game price, coin mechanism multipliers, and bonus play. The switches, on the game PCB at location B4, are accessible when the game PCB is mounted in place.

A special option allows you to charge by game or charge by player. The multipliers (toggles 4-6) determine how much each coin mechanism will be worth to the game's logic. The coin door has two mechanisms.

The basic unit of measurement is 25¢ or 1 DM, which equals a multiplier of x 1. Therefore, if you have a 2 DM/1 DM coin door, you may want to set the left multiplier at x 2 and the right multiplier at x1. You may offer bonus piay for certain combinations of coins inserted. For example, with the game set at 25¢ per play, players who deposit four successive quarters, then press the start button, can receive a bonus play. Therefore, players can receive five plays for $1.00. This bonus feature encourages players to insert more money than just the minimum 25¢ required for one game.

In the U.S., a “coin” is defined as 25¢. In Germany, a “coin” is 1 DM. To achieve bonus play, all coins must be inserted before pressing the start button.

Settings of 8-Toggle Switch on Space Duel game PCB (at B4) 8 7 6 5 4 2 1 Option

Off Off On On On oft On Off

Off On Off On Off Off On On

Off On

Off Off Off On

On

On.

Off Free play 1 coin for 1 game (or 1 player)* 1 coin for 2 game (or 2 players) 2 coins for 1 game (or 1 player) Right coin mech x 1 $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 in’)

Left coinmech x 1 $ Left coin mech x 2

Off Off No bonus coins $ For every 4 coins inserted, game logic adds 1 more coin For every 4 coins inserted, game logic adds 2 more coins For every 5 coins inserted, game logic adds 1 more coin For every 3 coins inserted, game logic adds 1 more coin** Off

On

*To charge by game: Toggle switch 4 at PCB location P10/11 to

To charge by player: Toggle switch 4 at PCB location P10/11 to “oft” $Manufacturer's recommended settings ** In Operator Information Display, this option displays same as no bonus.

Table 1-3 Special Option Settings

Settings of 4-Toggle Switch on the game PCB {at P10/11) 4 3 2 1 Option

On Off Credits counted on one coin counter. Credits counted on two separate coin counters. On 1-player game only On 2-credit minimum*

On Charge by game —@)

Off Charge by player**

*2 credits must be purchased before player can start game. ** Each player must have a credit to play the game.

1-41

Page 20

I. Game Play wes

The Space Duel™ game is a one- or two-player game with a color XY video display. This new display, with its 3 color guns and higher voltage, has the same technology that was used in previous Atari black-and-white X-Y displays. However, the screen now displays dazzling color and unique visual effects in a spectacular multi-dimensional video display.

Space Duel offers players a choice of four different game versions. One player can control a fighter or a space station. Two players, playing at the same time, can control fighters or a space station. The game offers players 12 different targets (7 split when hit), and 18 different waves. At the beginning of each wave, objects enter from the screen edge. The player(s) then tries to shoot and destroy the objects. The wave ends when all the objects are destroyed.

A special Operator Information Display shows game statistics and option switch settings. Enter this mode by turning the self-test switch to on. In this mode, you may clear the special “permanent” memory by erasing the high-score table or gametime information (see Section G).

A special Demonstration Mode allows you to view all waves as long as all ships are “alive” on the screen. In this mode you can see as many as 12 different targets (see Section H).

1-12 Space Duel™ has five possible modes of operation: attract, ready-to-play, play, high score and selftest. Self-test is a special mode for checking the game switches and computer functions. You may enter self-test at any time. Wait at least ten seconds after a game has been played before entering selftest or turning off the power. Otherwise, you may erase the high score table.

  • Attract Mode

The attract mode begins when power is applied to the game, after a play or high score mode, or after self-test. This mode is continuous and stops only when a credit is entered, or when in self-test. In the attract mode, the screen displays one of three possible pictures.

One of the pictures is the high score display which lasts about 8 seconds. The score(s) from the last game is displayed on the screen. The top five one-and two-player scores and their matching initials also appear for each type of game.

A second picture shows “Space Duel” letters on cubes. After a few seconds, ships and saucers appear. They shoot at the cubes. The cubes break into smaller cubes when hit, and disappear.

The third picture simulates game play. Fighters or space stations shoot at targets. In all pictures, game price information and number of ships appear at the top of the screen. Bonus level information and the copyright message appear at the bottom of the screen.

Page 21
  • Ready-to-Play Mode

This mode begins when a credit is entered. The screen displays four game versions (see the picture that follows).

  • COIN | GAME CREDITS b

2 PLAYERS | PLAYER & & A

SELECT GAME SELECT GAME

2 PLAYERS | PLAYER &—4 aH PRESS START SELECT GAME

Figure 1-6 Ready-to-Play Screen

If you do not see this picture, set switch 2 at PCB location P10/11 to off.

At the bottom of the screen one of three messages appears: @ ANOTHER COIN—not enough coins inserted @ SELECT GAME—enough coins inserted @ PRESS START—coins inserted, game selected

You must press GAME SELECT at least once, and then press START, to enter the play mode.

  • Play Mode The play mode begins with the first wave. In the space station game, two ships appear near the center of the screen. The ships are joined together by a “fuse.” In the fighter game, the red ship appears above the red controls. The green ship appears above the green controls. A sound is heard any time a ship appears on the screen.

Player controls consist of ROTATE LEFT, ROTATE RIGHT, THRUST, SHIELDS, and FIRE pushbuttons. A ship may fire as many as four shots on the screen at one time. However, if a ship is damaged, it may fire only one shot on the screen. Also the ship is slower to react. In space stations, a second hit to either ship destroys that ship. Then, the fuse between ships starts to burn, and the other ship explodes.

In the fighter game, players may shoot each other without losing a life. Instead, the ship blinks and disappears. After a period of time, the ship reappears in a different location. If one player loses all of his ships before the other player, his last ship returns to the screen as a damaged ship. It is possible to earn a bonus ship while damaged.

Shields protect a ship from all saucer shots and collisions. Shields wear out with time or if hit by targets. Space stations have more than twice as much shield energy as fighters.

In the first wave, spinners enter and break into two smaller pieces when shot. Each piece splits into two smaller pieces when shot again. Each of these pieces is destroyed when shot. Other targets split apart in the same manner.

At the end of each wave, a bonus wave begins and a low humming sound is heard. BONUS LEVEL, and the number of points for that level, flash on the screen. A box appears at the screen edge and ships cannot leave that boundary. Fuzzballs, stars and saucers enter and attack the player. A fighter, when shot by the other player, either just before or during the bonus wave, will not reappear until the next wave. The bonus wave ends when all targets are destroyed, or the humming sound reaches its highest pitch.

Other targets enter as the game progresses. When the number of targets is less than the wave number, or if no splitting targets have been hit in some time, saucer enters and shoots at targets and ships. The saucer shots become more accurate as play continues. Saucers may also enter as a pair. They shoot at, but do not destroy, each other. Anything caught between them will be shot. Each time the pair goes across the screen, the distance between them increases.

1:13

Page 22

A player's ship may be destroyed by a shot or collision. Game play ends when all ships are destroyed.

Hints for Game Play

@ Move your ship around. @ Stay away from the screen edges. @ Leave some of the larger targets on the screen, and shoot the smaller (divided) targets first. @ Destroy all splitting objects to get into the bonus wave. @ Move toward the target to make your shot more accurate. @ In the fighter game, shoot the other ship for 500 points each hit. @ In the fighter game, shoot the other ship to renew his shield power. @ in the fighter game, shoot the other ship just before the bonus wave. This keeps him out of the bonus wave. @ In the space station game, too much thrust causes you to spin, making it difficult to control and straighten the station.

  • High Score Mode This mode begins when a player has one of the five top scores. First, there is a fireworks display. Next, a player enters his initials following the instructions on the screen. Finally, the high score table for the version of game just played appears.

When you enter self-test, press reset, or turn the power off, all high scores are erased except the top score(s). The rest of the table is then reset at 5,000 points.

Table 1-4 Space Duel Targets

Target Description Wave First Appears Points

Spinner Enters from screen edge. Splits into two smaller targets first Ee time shot. Each target splits into two smaller targets next

time it is shot. Each of these targets is destroyed next time120/50/100

shot.

Oc\ahedronLyAction same as spinner.220/50/100
CubeBAction same as spinner.420/50/100
PentagonQOAction same as spinner.720/50/100
BookAction same as spinner.1020/50/100
8-Pointed StarXEAction same as spinner.13,20/50/100
HexagonAction same as spinner.1620/50/100
5-Pointed StarEnters from screen edge when only a few targets remain. IfBonus200

star leaves screen, it returns as a fuzzball.

Fuzzball se Enters from screen edge and tracks the ships. Bonus 200

MineEnters from screen edge, tracks ships and speeds up as play1100

progresses. When shot, stops and changes color. If hit -+ enough times, it turns white. Can only be destroyed if shot when white.

Saucer ee Enters from screen edge when number of targets is less 1 300

than the wave number. Shoots at targets and ships.

Saucer.Enters the screen from edge when number of targets is less1300

(SX _ than the wave number. Shoots at targets and ships. Enter as a pair and shoot at, but do not destroy, each other. Targets between pair are shot. As play progresses, distance between pair increases,

Page 23

A. Introductio

This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you isolate the failing portion of the game. The self-test procedure included in Chapter 7 is to help you decide if the game is or isn’t working properly. The expanded procedures in this chapter are included to help the qualified electronic technician determine why the game isn’t working properly.

If you are not a qualified technician, do not try to work on the game circuitry or video display. True, it is not earning money when it doesn’t work. However, your investment in this game may greatly increase if either the video display and/or game PCB are destroyed while you are working inside the game cabinet. Be assured, it isn’t worth it.

Chapter

Page 24

B. Commments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio Il PCB, or the color X-Y display?

The next step is to check all harness wires and connectors to the suspected failing assembly. If you find there is no harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly.

When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the assembly that is failing is the color X-Y display, we suggest that a qualified video display technician handle the troubleshooting and repair. If the power supply or Regulator/Audio || PCB is failing, troubleshooting and repair is relatively simple, as these assemblies are not too complicated. If the game PCB is failing, troubleshooting and repair will greatly depend on your understanding of the operation of this PCB.

To effectively troubleshoot problems of the game PCB, it is necessary for you, the technician, to become familiar with the PCB's hardware. The diagrams in the schematic package (included with the game) show the functions of the circuitry. Again, while troubleshooting this PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram.

To determine if the ROM of the game PCB that contains the self-test is functioning properly, perform signature analysis as described on the schematic diagrams. The signatures for the circuitry (printed in blue) are on the schematic diagrams at the proper test-node points.

A glossary of schematic signal descriptions is included at the end of this chapter. Each signal description states whether the signal is hardware- or software-generated, where it is generated, where the signal goes, and what the signal does to the circuitry. We suggest you use this glossary to become more familiar with the game PCB's operation.

2-2

C. Self-Test Procedure

To enter Self-Test, set the self-test switch to the on position. Then press the START and GAME SE- LECT buttons simultaneously. If the test passes, the screen goes blank for a few seconds, then Figure 2-1 is displayed, and the game will be silent.

Results if Test Fails:

In addition to the following failure indications, be sure to see the procedure for troubleshooting the game PCB with the CAT Box, at the end of the schematics.

Self-Test Figure 2-1 Screen if Test Passes

NOTE

This procedure does not test the coin door lockout coils. If the self-test passes, but the lockout coils do not energize when the self-test switch is set to off, suspect the lockout coil wiring, coin door harness, game PCB harness, latch R9, or driver Q2 of the game PCB.

SCREEN 1: SWITCH FAILURE is indicated by a constant tone. This means a switch is stuck in the closed position. Refer to Figure 1-5 for those switch locations.

RAM FAILURE is indicated by a sequence of 1 to 6 tones and an A displayed in the top center of the screen. Count the tones: the high one indicates the

Page 25

EDP 5 o4 q By IGNORE THESE NUMBERS

Figure 2-2 Self-Test Screen 1

bad RAM chip, as listed in the following table.

NOTE: If either of the first two RAM chips are bad, self-test can only produce the first two tones, not the whole sequence. You must replace the defective RAMs HI or El so the rest of the self-test can work properly. Bad RAM chip location High Tone on Game PCB Ist H1 2nd —1 3rd K7 4th M7 Sth J7 6th L7

ROM FAILURE is indicated by one or more vertically arranged numbers displayed in the top half of the screen, as shown in Figure 2-2. Ignore the right pair of numbers—the left number(s) indicates the following bad ROM(s):

Displayed Number Bad ROM Chip Locatons Jt 5 K/Lt 4 Mi 3 NIPt 2 Rt 1* NIP? o* R7 *If either or both of these ROMs are bad, you will hear a constant or intermittent iow tone, and the program may be unable to display a screen image.

EAROM OR CUSTOM I/O CHIP FAILURE is indicated by single letters in the top center of the screen. Identify the failure with the table below.

Displayed Letter Bad Chip Location E EAROM at M2 P Custom i/O Chip at C/D3 Q Custom I/O Chip at B3 To proceed to screens 2 through 5, close the slam switch or ground the DIAG STEP pad on the game PCB for each screen. By closing the slam switch, you can cycle through this group of screens.

SCREEN 2: A white diagonal grid pattern appears, along with the complete character set as shown in Figure 2-3. The corners of the grid pattern should touch the corners of the screen. If the display is not centered, symmetrical, or the proper size, adjust the X and Y SIZE, CTR, and LIN pots on the game PCB (see Space Duel™ Schematic Package, SP-181). If the characters are incorrect, check again for a0 or 7 displayed in the preceding ROM failure test.

Figure 2-3 Self-Test Screen 2 SCREEN 3: First, this test checks the two custom I/O chips’ audio outputs. This is done in an eight-beep progression. There are four tones, starting with the highest tone loud, then soft, then a lower tone loud, then soft. After two more tones, each loud then soft, the sequence repeats. Each loud tone tests the output of custom I/O chip at location C/D3, and each soft tone tests the chip at B3. No sound indicates failure of an audio amplifier, the custom I/O chip(s), and/or the game harness. Second, this test checks the vector-generator binary scaling circuitry. During the first beep, the boundary of the display is brighter. During the third beep, a rectangle half the size of the boundary is displayed. With each of the next six beeps, the rectangle is displayed one-half the previous size. This rectang!e then snaps back to full size, and repeats this shrinking sequence.

2-3

Page 26

If the display skips one of the seven rectangles, or if the progression is not one-half the previous rectangle, there is a problem in the scaling circuitry. SCREEN 5: A grid pattern touches the corners of the video display, as shown in Figure 2-6. Press the GAME SELECT button to change its color. Use this pattern for purity and convergence adjustments (see Color X-Y Display Manual).

EEE

Figure 2-4 Self-Test Screen 3

SCREEN 4: This test checks the seven screen colors and six intensities of each color (see Figure 2-5). If the intensities don't progress from dim at the top of each color group to bright at the bottom, there is a problem in the Z-axis of the PCB or the display. If the colors are not as shown in Figure 2-5, there is a problem with the R-G-B output of the PCB or the circuitry of the display. Use this pattern for tracking adjustments (see the Color X-Y Display Manual).

RED (R) \ ROYAL BLUE (B) GREEN (G)

—— WHITE (RGB)

YELLOW(RG) LIGHTBLUE(GB) LAVENDER (RB)

Figure 2-5 Self-Test Screen 4

2-4 EEE

Figure 2-6 Self-Test Screen 5

SCREEN 6: To display this screen, hold down GAME SELECT button while either closing the slam switch or grounding the DIAG STEP pad on the game PCB. To exit from this screen, turn off the self-test switch or press the RESET switch on the game PCB. When this test is entered, the screen will either be blank or display vectors, depending on settings of the switch toggles at location P10/11 on the game PCB. These screens are shown in Figure 2-7.

VECTOR-GENERATOR DIAGNOSTIC PROGRAM The diagnostic program is controlled by switches 2,3, and 4 in the 4-toggle option switch bank at location P10/11 on the game PCB. This group of switches lets you choose one of six tests. These tests provide recurring sequences to make it easy for you to troubleshoot the vector-generator circuitry. The tests and their respective option switch settings are as folllows:

Page 27

The last step of troubleshooting is to perform the tests described below.

Settings of 4-Toggle Switch Assy. at P10/11:

432
Test 1Do nothing but hit WDDIS every 4 msecOffOffOff

(blank screen)

Test 2Test vector-generator halt instructionOnOffOff

every .55 msec (blank screen)

Test 3Test vector-generator long vector (andOffOnOff

halt instruction) every 8.2 msec

Test 4Test vector-generator jump instructionOnOnOff

{and long vector and halt instruction) every 8.2 msec

Test 5Test vector-generator short vector instructionOffOffOn

(and all of Test 4) every 8.6 msec

Test 6Test vector-generator JSRL/RTSL instructionsOnOffOn

{and all of Test §) every 10.2 msec

Test 2(Blank screen)OffOnOn
Test 2(Blank screen)OnOnOn

Figure 2-7 Self-Test Screens During Signature Analysis

Page 28

D. Glossary of Schematic Signal Descriptions

(Signals Listed in Alphabetical Order)

AMO through AM12 Software-generated vector-generator read-only memory (ROM) or random-access memory (RAM) address inputs. These signals are equal to the microprocessor address lines ABO through AB12 when the microprocessor is addressing the vectorgenerator memory (VMEM is low). These signals are equal to the vector-generator address lines AVGO through AVG12 when the vector-generator program memory is not addressed by the microprocessor (VMEM is high).

AUD1 and AUD2 Software-generated audio signals from custom VO chips B3 and C/D3, amplified by operational amplifiers B5 and D5.

AVGO through AVG12 Software-generated vector-generator address lines from vector-generator address controller J9. These lines address the vector-generator program memory ROM or RAM through the vector-generator address selector, when the_microprocessor is not addressing vector memory (VMEM is high).

Bo2 Hardware-generated signal from the internal clock circuitry of the microprocessor and buffered by B1. When Be2 is high, address decoder L4 is enabled for the microprocessor to: @ Enable EAROM M2 in the high-score table circuit, Write to EAROM M2, Write an interrupt-acknowledge decode qutput to microprocessor IRQ counter J4, Reset the vector-generator halt flag, Clear the watchdog counter, Clear the vector-generator halt flag, or Write to the coin door outputs.

BUFFEN Active low software-generated signal from the vector-generator address selector multiplexer K8. This signal is directly from the microprocessor Bo2 signal. When low, BUFFEN enables vector memory data buffer P8 when the microprocessor is accessing vector memory. CENTER Software-generated signal that is active low when CNTR or HALT is low. This signal closes switch B10 of the X-axis output and E10 of the Y-axis output, resulting in bleeding the charges of X- and Y-axis holding capacitors C78 and C75. This centers the beam on the display.

DISRST Software-generated signal from the output of OR gate L6 that is low when either RESET from the microprocessor's watchdog circuit or VGRST from the microprocessor’s address decoder is low. When DISRST is low, the HALT output of the latch is preset high; the Z-axis data latch E6 is cleared; the Z-blanking counter M3 is cleared; the state machine {atch R4 is cleared; and the color data latch K10 is cleared.

DVGO0 through DVG7 Software-generated vector-generator data lines from the vector-generator program memory ROM or RAM. These data lines are fed to the vector-generator data shifters or to the microprocessor data bus.

DVXO through DVX12 Software-generated signals from vector-generator data shifter shift registers A8, C8 and B8, and from latch C6. The DVX3 through DVX11 inputs to the digital-to-analog converter (DAC) A/B9 represent the X-axis change from the current location of the display beam. If DVX12 is low, the DAC operates only in its lower 512 positions, or a negative direction of change. If DVX12 is high, the DAC operates only in its upper 512 positions, or a positive change.

DVYO0 through DVY12 Software-generated signals from vector-generator data shifter shift registers F8, J8 and H8, and from latch D6. The DVY3 through DVY11 inputs to DAC F9 represent the Y-axis change from the current location of the display beam. \f DVY12 is low, the DAC operates only in its lower 512 positions, or a negative direction of change. If DVY12 is high, the DAC operates only in its upper 512 positions, or a positive change. The DVYO through DVY2 signals also represent the eight color inputs of R-G-B latch K10; DVY4 through DVY7 represent the Z-intensity input of Z-axis latch E6; and DVY8 through DVY10 represent the number that the vector draw time is divided by in the scaling circuit. The draw time is divided by 2 (n= DVY8 through DVY10 binary number).

EAROMCON Software-generated signal from microprocessor address decoder L4 at address 0E80. This signal

Page 29

clocks microprocessor data bits DBO through DB3 to the control inputs of high-score table electrically alterable ROM (EAROM) M2.

EAROMRD Active low software-generated signal from microprocessor address decoder K6 at address 0A00. This signal enables the eight data bits of EAROM (electrically alterable ROM) M2 to be passed through buffer H2 of the high-score table.

EAROMWR Active low software-generated signal from micro- Processor address decoder L4 at address OFOO through OF3F. This signal clocks microprocessor address bits ABO through AB5 and data bits DBO through DB7 to the address and data bit inputs of high-score table EAROM M2.

Go Software signal in the vector-timer circuit that is active high when VCTR or CNTR is high. When GO goes high, the vector timer counts, at a 12-MHz rate, to its maximum count of 256, if OP1 is high and OP1 is low, or to 16K, if OP1 is low and OP1 is high. When the timer reaches its maximum count, STOP goes low, setting the VCTR and CNTR flag signals low on the next falling edge of 12 MHz.

HALT and HALT Software-generated signal from the halt flag that disables the halt and VCTR flags with its HALT output. The status of the HALT signal is read by the microprocessor on its buffered data input DB6 of the microprocessor’s switch input buffer M9 when SINP1 is low.

HALT* This signal results when the HALT signal has been delayed by one pulse of inverted VGCK (1.5 MHz), which in turn has been delayed by one pulse of 12 MHz. This signal is ORed together with GO and is the most-significant-bit address input of the state machine ROM.

INTACK Active low software-generated signal from micro- Processor address decoder L4 at address 0E00. This output is an acknowledgment from the microprocessor that it has received an interrupt request from the microprocessor's IRQ circuitry.

INVERT X Active high software signal from the coin door and control-panel output circuits. When this signal is latched high at the output of latch R9, switch B10 in the X-axis output circuit is closed, inverting the X-axis vector instruction to the display through inverter K9. INVERT Y Active high software signal from the coin door and control-panel output circuits. When this signal is latched high at the output of latch R9, switch E10 in the Y-axis output circuit is closed, inverting the Y-axis vector instruction to the display through inverter K9.

vos Active low software-generated signal from two ORed outputs of microprocessor address decoder P3. At addresses 1000 through 100F and 1400 through 140F, 10S is low, thus enabling bidirectional buffer F5 for the microprocessor to read data from custom I/O chips B3 or C/D3.

oo Active low software-generated signal from microprocessor address decoder P3 at addresses 1000 through 100F. When tow, this signal enables custom VO chip C/D3.

vot Active low software-generated signal from micro- Processor address decoder P3 at addresses 1400 through 140F. When low, this signal enables custom VO chip B3.

LATCHO Active low software-generated signal from the vector-generator state machine ROM decoder H7. When LATCH is low, data bits DVGO through DVG7 are transferred to the DVYO through DVY7 outputs of shift registers F8 and J8 on the next rising edge of 12 MHz.

Page 30

LATCH1 Active low software-generated signal from the vector-generator state machine ROM decoder H7. When LATCH1 is low, data bits DVX3 through DVX11 are all set low at the outputs of shift registers A8, B8 and C8; data bits DVYO through DVY7 are all set low at the outputs of shift registers F8 and J8; and data signals DVGO through DVG3 are transferred to the DVY8 through DVY11 outputs of shift register H8 on the next rising edge of 12 MHz. OPO through OP2 and DVY12 (from DVG4 through DVG7) are latched at the output of latch D6; and ZO through Z2 and DVX12 are set low at the outputs of latch C6.

LATCH2 Active low software-generated signal from the vector-generator state machine ROM decoder H7, When LATCH2 is low, data bits DVG3 through DVG7 are transferred to the DVX3 through DVX7 outputs of shift registers A8 and C8 on the next rising edge of 12 MHz.

LATCH3 Active low software-generated signal from the vector-generator state machine ROM decoder H7. When LA is low, data bits DVG4 through DVG7 are transferred to the DVX8 through DVX11 outputs of shift register B8 on the next rising edge of 12 Mkz. Latch C6, ZO through Z2, and DVX12 from data bits DVG4 through DVG7 are latched at the output of latch C6.

NORM and NORM Active high software-generated signal from the normalization (NORM) flag latch A6. NORM is set high and NORM is set low, when STROBEO goes high, if OPO is high and if CNTR, SCALE, and VCTR are all low. DVX11, DVX12, DVY11 and DVY12 must all be high or all low. When NORM goes high, the vector draw time of the vector-generator timer is divided by 2. Each n divide is clocked by 12 MHz while NORM multiplies (shift left) the rate of change of the vector X and Y data in the vector data shifter at the same 2” factor. The n number is incremented at the 12-MHz rate until either DVX11 or DVY11 changes state. When either goes high, NORM is cleared low, and NORM is set high by the high clear input of NORM latch A6.

OPO and OPO Software-generated signals from vector-generator data-shifter latch D6. OPO is latched active high and OPO is latched active low when LATCH1 goes high, if vector-generator data bit DVGS5 is high. Signals OPO through OP2 are three of the eight address inputs to vector-generator state-machine ROM N4. These signals instruct the operation of the state

machine. A righ oaes® the HALT output of latch

L5 high, when STROBES goes from low to high. OPO and OP2 are gated together, along with STROBES and VGCK to set the vector (VCTR) flag output of latch ES. Vector flag VCTR will be valid only if OPO and OP2 are both low. When BEO goes high, the normalization (NORM) flag is set low at the output of latch A6.

OP1 and OPi Software-generated signals from vector-generator data shifter latch D6. OP1 is latched active high and OP1 is latched active low when LATCH1 goes high, if vector-generator data bit DVG6 is high. Signals OPO through OP2 are three of the eight address inputs to vector-generator state machine ROM N4. These signals instruct the operation of the state machine. __ In the vector-generator timer, the low OP1 signal input decreases the maximum count capabilities of the timer from 32K counts to 256 counts (a short vector) before causing a STOP timer output. The high OP1 signal enables a 1 to be loaded into the D input of counter P6 if NORM or NORM is low.

OP2 and OP2 Software-generated signals from vector-generator data latch D6. OP2 is latched active high and OP2 active low when LATCH1 goes high, if vector-generator data bit DVG7 is high. Signals OPO through OP2 are three of the eight address inputs to vectorgenerator state machine ROM N4. These signals instruct the operation of the state machine. When OP2, OPO, STROBES and VGCK are all low, VCTR goes high on the next falling edge of 12 MHz (beginning a vector trace) if STOP and HALT are

Page 31

both high. When STOP goes low (vector timer has reached maximum count), VCTR goes low. If OP2 and OP2 are active, CNTR goes high on the next falling edge of 12 MHz, if STROBES is low and when VGCK goes low. When STOP goes low, CNTR goes low on the next falling edge of 12 MHz. If OP2 and STROBE1 are both low, latched data signals DVY8 through DVY10 (at the output of latch D7 in the vector-scaling circuit) are loaded into counter C7. When STROBE1 goes high, counter C7 counts down until it reaches the minimum count. At the same time, the timer circuit does a divide-by-2 (shift right) operation for each count of counter C7, caused by a valid SCALE input to the timer. When C7 reaches its minimum count, its minimum/maximum (M/M) output goes high, causing SCALE to go low. If OP2, STROBE2, and DVY12 are low, new scaling data (DVY8 through DVY10) is latched at the output of vector-scaling circuit latch D7. If DVY12 is low, Z-axis data signals DVY4 through DVY7 are latched at the output of latch E6 in the Z-axis output circuit.

OUTPUT Active low software-generated signal from microprocessor address decoder L4 at address 0CO0O. When low, the microprocessor outputs to the coindoor coin counters, control-panel LEDs and the X and Y axis invert circuits on buffered data bits DBO through DB7.

POR Hardware-generated signal in the power-on reset circuit that is low when voltage at plus input is less than about 7 volts. This also protects the microprocessor against glitches on the power line input. It is assumed that if the 10.3V input has a glitch on it, then the +5V input to the game PCB will also have a glitch.

RAMO Active low software-generated signal from microprocessor address decoder P3 at addresses 0000 through 03FF. This signal enables RAMs E1 and H1. RESET Hardware-generated signal from watchdog circuitry or the power-on reset circuitry. The power-on reset circuitry causes this signal to be low while the voltages of the power-supply input are reaching their regulated levels, guaranteeing that the address lines of the microprocessor are stabilized before letting the microprocessor do its thing. The watchdog circuitry causes RESET to go low if the microprocessor fails to output address 0DO0 before the watchdog counter H4 reaches its maximum count.

ROM Active low software-generated signal from micro- Processor address decoder R2 at addresses 4000 through FFFF. This signal enables ROM data buffer €2 and bidirectional buffer F2 for the microprocessor to read data from the ROMs.

ROMO Active low software-generated signal from microprocessor address decoder R2 at addresses 4000 through 4FFF. This signal selects microprocessor program memory ROM R1.

ROM1 Active low software-generated signal from micro- Processor address decoder R2 at addresses 5000 through 5FFF. This signal selects microprocessor program memory ROM N/P1.

ROM2 Active low software-generated signal from microprocessor address decoder R2 at addresses 6000 through 6FFF. This signal selects microprocessor program memory ROM M1.

ROM3. Active low software-generated signal from microprocessor address decoder R2 at addresses 7000 through 7FFF. This signal selects microprocessor program memory ROM KI/L1.

ROM4 Active low software-generated signal from inverted microprocessor address line A15 at addresses 8000 through FFFF. This signal selects microprocessor program memory ROM J1.

RWB Active low software-generated signai from the microprocessor, R/W output, buffered by B1 and inverted by F3. When this signal is low, decoder K6 of the microprocessor address decoder is enabled from the microprocessor to do the following: read data from EAROM M2 (in the high-score table circuit) on data lines DBO through DB7; read switch data on data lines DBO through DB? through the buffer M9; or read switch data on data lines DB6 and DB7 from multiplexers L9 and N9.

Page 32

SAEN Unused test point.

SCALE Hardware-generated signal activated by software from the vector-scaling circuit. SCALE is active high when OP2 is high and counter C7 is counting down (at a 12 MHz rate) from the number loaded into counter C7 from the output of scale latch D7. SCALE stays high until counter C7 reaches the 0 count. For each count of counter C7, the vector timer does a load operation at the same 12-MHz rate. The result is a divide of the vector draw time by a factor of 2". The value of n is equal to the total counts of C7.

SCALELD Software-generated signal that is active low when STROBE2, OP2 and DVY12 are all ow. Scale data bits DVY8 through DVY10 are latched at the outputs of latch D7 when SCALELD goes high.

STATCLK Software-generated signal that is active low when STROBE2, OP2 and DVY12 are all low. Color data bits DVYO through DVY2 are latched at the outputs of latch K10 when STATCLK goes high. STATCLK

also latches Z data bits DVY4 iprougr DVY7 at the

output of Z-axis latch E6 when STATCLK goes high.

STOP Hardware-generated signal from the vector timer. When STOP goes low, the vector timer has reached its maximum count. The low STOP causes the VCTR and CNTR flags to be set low on the next falling edge of 12 MHz.

STROBEO Active low software-generated signal from the Wee generator state machine ROM decoder H7. When § BEO goes from a low to ahigh, the state of OPO is transferred to the output of latch A6. If OPO is low, NORM will go low. IF OPO is high and CNTR, SCALE, VCTR, DVX11, DVX12, DVY11 and DVY12 are all low, NORM goes high when STROBEO goes from low to high.

STROBE1 Active low software-generated signal from the vector-generator state machine ROM decoder H7.

When STROBE: goes low and if OP2 is low, scaling

bits latched at the outputs of latch D7 are loaded into counter C7. When STROBE1 goes high, counter C7 begins counting down at a 12-MHz rate from the loaded count input. As the counter counts, the minimum/maximum (M/M) output of the counter is low, resulting in a high SCALE signal input to the vector timer. When the count of C7 reaches zero, the M/M output of the counter goes high, making SCALE low.

2-10 STROBE2 Active low software-generated signal from the vector generator state machine ROM decoder H7. When BE2 and OP2 are both low and DVY12 is low, STATCLK goes low. If DVY12 is high, SCALELD goes low.

STROBES Active iow software-generated signal from the vector-generator state machine ROM decoder H7.

When g ROBES is low, VCTR is set high, OPO and

OP2 are low on the falling edge of VGCK, delayed by falling edge of 12 MHz. In addition, CNTR is set high, if OP2 is high on the falling edge of VGCK, delayed by falling edge of 12 MHz. If OPO is high, HALT goes high when STROBES goes from a low to a high.

STO through ST2 Software-generated instructions from vector-generator state machine ROM N4. neers outputs from the ROM are decoded for the through TATCH 3 and STROBEO through STROBES outputs of decoder H7. STO through ST2, plus the highest data bit output from the ROM, are latched at the output of latch Ré4 for the four lowest-bit inputs of ROM NA.

Page 33

Pen ST3 Hardware-generated signal from the output of state machine control flip-flop A7. This signal is the inverted state of VGCK (1.5 MHz), delayed by one pulse of 12 MHz, if the most-significant-bit output of state machine ROM N4 is low and VMEM is high. If the output bit of ROM N4 is high, ST3 is high. When ST3 is low, one of eight outputs of state machine decoder H7 are selected by STO through ST2. When ST3 is high, all outputs of decoder H7 are disabled.

VCTR Software-generated signal from the VCTR flag.

When HALT from the halt flag is low, VCTR is set HALT goes high. When OPO, OP2, STROBES and

low_and VCTR is set high and remains high until

VGCK are all low, VCTR goes high on the next failing edge of 12 MHz. When VCTR is high, NORM is set low with a low clear input to NORM flag A6. A high VCTR causes the vector timer to do the following: start its draw time counter with a high GO input; latch the Z-axis intensity data at the outputs of latch H6; and enable X- and Y-axis digital-to-analog converters A/B9 and FQ for drawing the vector. When STOP is received at the input of the VCTR flag, VCTR is set low and VCTR is set high. VGCK Hardware-generated signal that is 1.5 MHz passed through buffer B1. This is the basic timing signal of the vector generator that clocks state machine latch R4.

VGGO Software-generated decode from microcomputer address decoder L4 at address 0C80 that sets HALT of the halt flag low.

VGRST Software-generated signal from the address decoder at address 0D80 that is ORed together with RESET to produce DISRST.

VMEM Software-generated signal from the microcomputer address decoder, from addresses 2000 through 3FFF. This signal, when low, selects the microprocessor addresses through address-selector multiplexers K8, L8, M8 and N8. This signal is also conditioned by flip-flops L5 and A7 and by various gates to disable state machine decoder H7 with a high ST3 input. This signal kills the clock of state machine latch Ré4 of the vector generator.

VRAMO Active low software-generated signal from vectorgenerator address decoder K6 at address locations 2000 through 23FF. When low, RAMs K7 and M7 are enabled.

VRAM1 Active low software-generated signal from vectorgenerator address decoder K6 at address locations 2400 through 27FF. When low, RAMs J7 and L7 are enabled.

VROM1 Active low software-generated signal from vectorgenerator address decoder K6 at address locations 2800 through 2FFF. When VROM1 is low, vector ROM R7 is enabled.

VROM2 Active low software-generated signal from address controller J9 and inverted by inverter K9 at address locations 3000 through 3FFF. When low, ROM N/P7 is enabled.

vw Software-generated signal from vector-generator

address selector multiplexer K8. When oMEM is

low, VW is from the microprocessor R/WB. When VMEN is high, this signal is held high by pull-up resistor R83. When VW is low, data is written to the vector RAM from the microprocessor. When VW is high, data may be read from the vector RAM.

Page 34

‘Space Duel™

WoDISs, Test point in the microprocessor watchdog circuit that, when grounded, prevents RESET from going low (except when RESET button is pressed).

ZO through 22 Software-generated signals from vector-generator data shifter latch C6. ZO is latched active high in the vector data shifter, if data bit DVG5 is high when LATCHS goes tow. Z1 is latched active high and Z1 is latched active low, if data bit DVG6 is high when TATCH3 goes low. Z2 is latched active high and 2 is latched active low, if data bit DVG7 is high when 3 goes low. These signals are the Z-axis inputs to the Z-axis digital-to-analog converter if they are less than or greater than the binary count 1. When the VCTR signal goes high, these Z-intensity bits are latched at the output of latch H6. If the count at the output of the latch is zero, the conditions are met with the all-high inputs of NAND gate H5 for a high ZBLANK signal to the video display, turning the video display beam off. If the count is greater than one, the binary count determines the bias of transistor Q7, resulting in one of six possible Z-axis level outputs to the video display. If the Z count is 1, the conditions are met with all high inputs to AND gate F5 fora high S(select) input to multiplexer F6. This results in selecting the Z data latched directly from data bits DVY4 through DVY7 when STATCLK goes low. in this case, the one of sixteen binary count determines the bias of transistor Q7. 3KHz Hardware-generated signal from the clock circuitry read by the microprocessor through the coin door and control-panel input circuits on data line DB6 through switch input buffer M9 when SINP1 is low. This frequency is used by the microprocessor as its time reference.

3MHz Hardware-generated signal from the clock circuit. This is one of the conditioning signals in the vector state machine control circuitry for delaying the time when VMEM kills the state machine clock and disables the state machine decoder.

6MHz Hardware-generated signal from the clock circuitry. This is one of the Conditioning signals in the vector state machine control circuitry for delaying the time when VMEM kills the state machine clock and disables the state machine decoder.

12KHz Hardware-generated signa! from the clock circuitry. The signal is used to clock timer A4 of the highscore table circuit.

12MHz Hardware-generated signal from the clock circuit- Ty. This is the basic timing that determines the resolution of the vector generator.

o0 Hardware-generated signal used for the clock of microprocessor C2; this signal is equal to 1.5 MHz.

Page 35

Maintenance, Repair

and Parts

o

In addition to maintenance and repair information, this chapter provides the necessary information for you to order parts for your Space Duel™ Upright and Cocktail games. Please note that, for simplicity, common hardware has been deleted from most of the parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.

When ordering parts, please give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Atari Customer Service numbers are listed in the front of this manual for your convenience.

Page 36

Schematics, Self-Test Label & Manuals— see parts list on following page

Fluor. Light & Speaker— A037295-01 see Figure 3-4 (Cabinet Assy.) 178034-024 (Molding)

03733201 (Vent. Grille)

Video Display— see Figure 3-5

74-2110 (Lock) Control Panel Assy.— see Figures 3-2 & 3-3

037419-02 178013-001 (Rear Panel) (Latch)

037308-01 (Grille) Le 148001.001 (oy (Speaker)

‘4007638-01 (Siam Sw). ‘nD _ Game PCB Assy.— erate see Figures 3-7 & 3-8

A037938-01 ‘A037491-01 (Main Harn.) ‘Coin Box) RegJAudio Il PCB Assy.— see Figures 3-7 & 3-9

A037940-01 (Pwr, Harn.)

A002465-01 (Coin Counter) ‘A038004-01 (Vol /Self-Test Harn.) 19-9032 (Vol. Ctrl.) 62041 (Util. Coir, Sw.)

69-001A037470-01Webra

(On/Ott S :

(Selftest Sw.)Power Supply Assy.—178048001OHHSw.)9937455-03 oF
038003-01see Figure 3-10(Caster)00999201‘A037784-03

Bracket) (OnlOlt Sw. Cv) (Power Cord)

Figure 3-1 Upright Cabinet-Mounted Assemblies A037294-xx A

Page 37

‘Space Duel™

Figure 3-1, continued Upright Cabinet-Mounted Assemblies Parts List

Part No. Description A002465-01 Coin Counter A007638-01 Slam Switch Assembly

A037295-01Cabinet Assembly(includes legs and PCB retainers, but not the rear access panel)
A037453-03Strain-Relief Power Cord(U.S. and Canada)
A037454-03Strain-Relief Power Cord(Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece,

Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)

A037455-03Strain-Relief Power Cord(Australia and New Zealand)

A037470-01 Power On/Off Switch/Mounting Plate Assembly A037491-01 Coin Box A037784-03 Strain-Relief Power Cord Assembly (United Kingdom, Ireland, Lebanon, Saudi Arabia, India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe) A038004-01 Harness for Volume Control/Self-Test Switch/Coin Counter Assembly A037938-01 Main Harness Assembly A037940-01 Power Harness Assembly The following four items are the technical information supplements to this game: SP-181 Space Duel™ Schematic Package ‘ST-181-01 Space Duel Label with Self-Test Procedure and Option Switch Settings TM-181 Space Duel Operation, Maintenance and Service Manual TM-183, Service Manual for 19-Inch Wells Gardner Color X-Y Display 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 71-2110 Panel Cartridge Lock Mechanism (for rear access panel) 78-3201 Cabinet-Leveling Leg 009992-01 On/Off Switch Cover 036686-01 Card of Game Pricing Labels (not shown in illustration) 037308-01 Speaker Grille

037331-01Side Panel Decal(For Ireland build only. Not shown in illustration)
037332-01Ventilation Grille(located on cabinet top)
037419-02Rear Access Panel(does not include lock)

038003-01 Bracket for Volume Control, Self-Test Switch and Coin Counter(s) 148001-001 6 x 9-Inch 4-Ohm 15W Oval High-Fidelity Speaker 178013-001 Spring Draw Latch 178034-024 %-Inch Black Plastic T-Molding 178048-001 Rigid Caster

3-3

Page 38

037839.01 03742701 Schematics, SelfTest Label & Manuals— 035852-01 (Bracket) (Foam) 82-406 see parts list on following page (Bracket) (Eyebolt)

178034-026 (Folding) 038111-02 78-6A00401 (Table Top) (Tape)

038129.01 78-6900401 (Tape) edad

aed Video Display—

(ShielIsee Figure 3-5

‘A038028-01 035851-01 (hinge) (Main Harn) Game PCB— 78-3118 see Figures 3-7 & 3-8 (Support) 4038030-01 038133-01 (Power Harn.) (Bar) ‘A037450-01

Control Panel— (inter), Sw/Brkt. Assy.) see Figures 3-2 & 3-3 007882-02 62.039 (interl. Sw. vr.) (Stat Sw) 71-2110 037843-01 (Lock) (Start Sw. Bracket) 71-3201 036895-01 (Lock Wshr.) (Bezel) 036764-01 (Cam) ist) Power Supply— 038121.02 see Figure 3-10 (Access Pri.)

037827-01 oe (Backpiate) { 171002.001 178034-024 rate (FMolding) 038130-01 Coin Door— Grille) see Figure 3-6 RegJAudio I! PCB— 62.041 see Figures 3-7 & 3-9 (Coin Sw.) NV

19.90324‘037470-01

(Volume Ctr!) a (On/Off Sw./Plate Assy.) 009992.01 69-001 earesiee) (On/Off Sw. Cvr.) saarhnad A038107-02 (Nut) (Rear Leg) 037865-01

(Bracket)A037491.01A037453-02,
{Coin Box)148001-001A037454-02,
4037292-01‘002465-01(Speaker)37455-02 or

(Leg Supp. Assy.) 2 (Coin Counter) (Power Cord)

A038107-01A007638-01—47g934.025A038102-01178013-001
(Front Leg)(Slam Sw. Assy)—(TMolding)(Cab. Base) _ (Latch)

037335-03 (Grace) ; . : : 733206 Figure 3-1, continued Cocktail Cabinet-Mounted (Leg) Assemblies A038100-xx A

Page 39

Space Due!™

Figure 3-1, continued Cocktail Cabinet-Mounted Assemblies Parts List

Part No. Description A002465-01 Coin Counter A007638-01 Siam Switch Assembly

A037292-01Leg Support Assembly(includes endcap)

A037450-01 Interlock Switch/Bracket Assembly

A037453-02Strain-Relief Power Cord(U.S. and Canada)
A037454.02Strain-Relief Power Cord(Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece,

Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)

A037455-02Strain-Relief Power Cord(Australia and New Zealand)

A037470-01 Power On/Off Switch/Mounting Plate Assembly A037491.01 Coin Box A037784-02 Strain-Relief Power Cord Assembly United Kingdom, Ireland, Lebanon, Saud/ Arabia, India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe) A038028-01 Main Harness Assembly A038030-01 Power Harness Assembly

A038102-01Cabinet Base Assembly(includes leg backplates, PCB retainers, and access panel}

A038107-01 Front Leg Assembly (includes leg, 2 adjustable feet and 2 endcaps) A038107-02 Rear Leg Assembly (includes leg, 2 adjustable feet and 2 endcaps) The following four items are the technical information supplements to this game: SP-181 Space Duel™ Schematic Package ST-181-02 Space Duel/Cocktail Label with Self-Test Procedure and Option Switch Settings TM-181 Space Duel Operation, Maintenance and Service Manual TM-183, Service Manual for 19-Inch Welis Gardner Color X-Y Display 19-9032 50 Ohm, 1272W Wire-Wound Rheostat (for volume control) 62-039 SPDT Momentary-Contact LED Start Switch 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch 69-001 DPDT Self-Test Switch 71-2110 Panel Cartridge Lock Mechanism (for table top) 71-3201 34-Inch Anchor Washer for Table-Top Lock

75-9910NO#°,-11 Steel Stamped Nut(for utility coin switch)

78-3118 Hinged Table-Top Support

78-3206 Cabinet-Leveling Leg 78-6A00401 Vinyl Foam Double-Coated-Adhesive Tape 14-inch wide x !,-inch thich (22 in. required) 78-6900401 Vinyl Foam Single-Coated-Adhesive Tape %-inch wide x ¥,-inch thick (12 in. required) 82-406 #¥%4-20 x 2-Inch Eyebolt with %4-Inch Threads 007882-02 Interiock Switch Cover 009992-01 On/Off Switch Cover 035851-01 Table-Top Hinge 035852-01 Corner Bracket for Table Top 036764-01 Hook-Type Cam (for table-top lock) 036895-01 Black Malded Switch Bezel 037335-03 Leg Brace 037427-01 Foam Vibration Damper (for table top) 037827-01 Leg Backplate 037839-01 Spring Draw Latch Bracket 037843-01 Start Switch Mounting Bracket 037865-01 Bracket for Volume Control, Self-Test Switch and Coin Counter [Continued on next page}

3-5

Page 40

Space Duel \™

Figure 3-1, continued Cocktail Cabinet-Mounted Assemblies Parts List

Part No. Description 038111-02 Wood Table Top 038121-02 Access Panel 038129-01 Video Display Overlay 038130-01 Speaker/Fan Grille 038133-01 Security Bar 038148-01 Display Shield with Graphics 148001-001 6 x 9-Inch, 4-Ohm, 15W Oval High-Fidelity Speaker 171002-001 110V Cooling Fan 178013-001 Spring Draw Latch

178034-02434-Inch Black Plastic T-Molding(for center cabinet base)
178034-025*,,-Inch Black Plastic T-Molding(for cabinet ends)
178034-026'¥,-Inch Black Plastic TMolding(for table top)

3-6

Page 41
WARNING Prior to removing or repairing any printedcircuit board, unplug the game.

To Open the Control Panel:

  • To open the control panel on the Upright game, open the coin door. Reach up through the opening to the top of the control panel. Open the springdraw latches. Close the coin door. Lift up on the control panel at the top-most edge and tilt it toward you.
  • The control panel edge next to the display shield has foam tape applied to it. This tape acts as a cushion for the giass and prevents spilled liquids from entering the cabinet interior. Always make sure this tape is in good condition.
  • To open the control panel on the Cocktail game, remove the Allen-head screws. Then, tilt the control panel toward you.

LEAF SWITCH Leaf Switch Repair:

@ Adjust the leaf switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the cross-bar contacts provides a selfcleaning feature. Don’t burnish the contacts. To clean them, use electrical contact cleaner.

@ To replace a leaf switch, remove the screw with a Phillips-head screwdriver.

To replace the switch button, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The ring on the outside of the control panel should not spin, due to its design.

To reinstall a switch, reconnect the harness wires as shown in the Schematic Package, Game Wiring Diagram. Make certain the right colors go to the right tabs on the switch.

Open panel in the order indicated. (Circied numbers match the numbered instructions).

Figure 3-2 The Control Panel

3-7

Page 42

‘Space Duel™

LED Start- and Select-Switch Repair: The LED switches have a very low failure rate. In case a Switch should ever be suspect, first test it per the description that follows.

To Test LED Switch:

@ Remove the wires from the suspected switch. @ Attach the leads of an ohmmeter to normally open and common contacts. @ Check contacts (push and release the switch button) for closed and open continuity.

UPRIGHT CABINET -I

START SWITCH

BLUE 1 RED(+) 5 Bou NORMALLY OPEN

BLACK (N.0.) CONTACT

COMMON CONTACT

SELECT SWITCH

WHITE/GREEN ary] neo.) aw WHITE/BLUE ws NORMALLY OPEN (N.O.) CONTACT BLACK COMMON CONTACT

SELECT SWITCH

WHITE/YELLOW aT | neoto) 4 WHITE/GREEN NORMALLY OPEN (N.O} CONTACT ts

BLACK COMMON CONTACT COCKTAIL CABINET ql @ If the contacts do not operate sharply or always remain closed or open, then replace the LED switch.

To Replace LED Switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires as shown.

START SWITCH

WHITE/RED:

WHITE/BLACK NORMALLY OPEN (N.0) CONTACT RED(+) ls

BLACK COMMON CONTACT

Figure 3-2 The Control Panel, continued

3-8

Page 43
WARNING

Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.

NOTE Cocktail cabinet LED is on a separate panel (not shown in this illustration).

78-6900402 (Tape)

62.039 {LED Switch) 160013-001 (Leaf Sw./Button Holder) 178030-004 (Red Button} 178030-005 (Green Button)

037299-01 i 03730101 | trl. Pr!) (Giri. Pr /Decal) 037300-01 (Decal—not shown)

038127-01 ‘A038105-01 (Ctrl. Pri.) 2 036895-01 Wri. Pni/Decal) 038149-01 (Sw. Bezel) (Becal—not shown) i A037942-01 (Harness) =i) A038032-01 . A (Hames) Figure 3-3 Control Panel Assemblies Upright A037302-01 A and Cocktail A038104-xx A

Parts List

Part No. Description

A037301-01 Upright Control Panel with Decal A037942-01 Upright Control Panel Harness Assembly A038032-01 Cocktail Control Panel Harness Assembly A038105-01 Cocktail Control Panel with Decal 62.039 SPDT Momentary Pushbutton Start Switch, with Red Light-Emitting Diode 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, %4-inch wide x |,-inch thick (24 in. required) 036895-01 Black Molded Switch Bezel 037299-01 Upright Control Pane! 037300-01 Upright Control Panel Decal 038127-01 Cocktail Contro! Panel 038149-01 Cocktail Contro! Panel Decal 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001} 178030-004 Red Pushbutton Assembly 178030-005 Green Pushbutton Assembly

Page 44
WARNING Prior to removing or repairing the speaker, fluorescent tube or fan, unplug the game. \f you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

To Replace Fluorescent Tube: 1, At the top front of the game, remove the three sets of hardware that secure the upper attractionpanel retainer to the cabinet. Loosen the three sets of hardware that secure the lower retainer to the cabinet. Lift the attraction panel up and out of its lower retainer.

  • Remove the cardboard locking tab at each end of the tube. Slightly rotate the tube up or down, and carefully remove it from the lampholders. Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion/ Replace the locking tabs. Check that the green ground wire is securely attached to the large meta! bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start. ad

Sad

037309-01 (Retainer)

179035-001 (Lampholder) To Replace Upright Cabinet Speakers:

  • Upper speakers—from the back of the cabinet, unplug the 5-pin harness connector just behind the speaker board. From the front of the cabinet, remove the screws that secure the light board to the cabinet. Slide the board out of the cabinet.
  • Unplug the two plug-in connectors on the speaker. Remove the hardware that attaches the speaker to the board. Replace the speaker, reinstall the wood board and reconnect the harness. @ Lower speakers—unplug the two plug-in connectors on the speaker. Remove the hardware that attaches the speaker to the cabinet. Install the new speaker, and replace the hardware and connectors.

To Replace Cocktail Speaker and Fan:

Unplug the game and unlock and open the table top. Let the Regulator/Audio I! PCB heat sink coo! down for about 10 minutes.

To remove the speaker or fan, unplug the wire connectors. Use a short-handled Phillips screwdriver to remove the screws that attach the speaker or the fan to the cabinet wall. Repair or replace the speaker or fan as required. Make sure the green ground wire is securely attached when replacing the fan.

79-561816P_ (Wire Nut) 142028-xxx 99-1103 (Starter) (Transformer)

99-11009 (Socket) 403794301 (Harness)

037318-01 (Attraction Glass) 148001001 bee (Speaker)

'037469-01 (@ A03754001 (Bracket) (Grd. Wire)

037304-01 (Retainer) 99-11006 NOTE (Tab) To ensure that the fluorescent tube starts, make sure the ground wire is firmly attached to both the ballast transformer and the steel lamp bracket. Disassemble in the order indicated. (Circled numbers match the numbered instructions.) 70-304 o— 7% (Tube)

Figure 3-4 Speaker, Fluorescent Tube and Fan

3-10

Page 45

Figure 3-4 Speaker, Fluorescent Tube and Fan, continued A037319-01 & -02 A

Parts List

Part No. Description A037540-01 Ground Wire with Ring Lug A037943-01 Light and Speaker Harness 70-304 18-Inch 15-Watt Coo! White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape (48 in. required) 79-561816P Spring-Connector Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter 99-11008 Fluorescent Lamp Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037304-01 Bottom Attraction Glass Retainer 037309-01 Top Attraction Glass Retainer 037318-01 Attraction Glass with Graphics 037 469-01 Steel Lamp Bracket 142028-001 60-Hz 118-Volt Ballast Transformer (used on AQ37319-01 assembly) 142028-002 50-Hz 118-Volt Ballast Transformer (used on A037319-02 assembly) 148001-001 6 x9-Inch 4-Ohm 15-Watt Oval High-Fidelity Speaker _ 171002-001 110V Cocktail Cooling Fan (not shown in illustration) =} 179035-001 2-Pin Fluorescent Lampholder

Page 46

@ 93732201

@

3-12 037303-01 (Shield) A WARNING: Shock Hazard

The following procedure should only be performed by a qualified service technician. Prior to removing or repairing the video display, unplug the game. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube. High voltages may exist in any video display, even with power disconnected. Use extreme caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! Implosion Hazard If you drop the display and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any display.

92-953 (Display) (Bezel)

Figure 3-5 UPRIGHT CABINET

To Remove Color X-Y Display: . Open the control panel (see Figure 3-2, The Control Panel).

  • Lift up on the glass shield. Slide the retainer clip off the wood cleat and remove through the cutout. Then remove the glass shield by sliding it down and out of the cabinet.
  • Remove the cardboard bezel.
  • Open the rear access panel and unplug the 15-pin display harness connector.

5, Remove the four sets of hardware that secure the display frame to the wood shelf.

  • Carefuily pull the display out through the front of the cabinet.

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

L®

037330-01 (Retainer)

SCREEN (Brightness)

BACK OF DISPLAY

Upright Video Display Removal

Page 47

COCKTAIL TABLE CABINET

To Remove Color X-Y Display:

  • Unplug the game. Unlock and open the table top and access panel (See Chapter 1).
  • Remove the display bezel. Remove the four hexhead machine screws that attach the display frame to the metal diaplay mounting brackets.

038129-01 (Overlay)

038148-01 (Shield)

038131-01 (Bracket)

038132-01 (Bracket)

Disassemble in the order indicated. (Circled numbers match the numbered instructions) ‘Space Duel™

  • Reach through the access panel opening and unplug the 15-pin video display connector underneath the display.
  • Grasp the video-display frame flanges on each side of the display and carefully lift the display assembly up and out the cabinet. After servicing, reassemble in reverse order.

038147-01 (Bezel)

92-053 (Display)

A038033-01 (Display Harn.)

Figure 3-5 continued, Cocktail Video Display Removal VA037294-01 A and VA038100-01 A

Parts List

Part No. Description

A038033-01 Cocktail Display Harness Assembly 92-053 19-Inch Wells-Gardner Color X-Y Video Display 037303-01 Upright Display Shield 037322-01 Upright Display Bezel 037330-01 Upright Display Shield Retainer 038129-01 Cocktail Display Overlay 038131-01 Cockiail Display Mounting Bracket (for /eft side) 038132-01 Cocktail Display Mounting Bracket (for right side) 038147-01 Cocktail Display Bezel 038148-01 Cocktail Display Shield with Graphics

3-13

Page 48

Space Duei™

99-15051 (Lamp Helder)

99-15026 (Coin Inlet) 99-15056 (Screw for Bezel)

99-15025 ———»_ (Coin Iniet)

PART OF 99-15041 99-15055 t 99-15041 (Retng Screw) Ay {Lockout Coil)

99-15053 (Lockt. Coil Soring) !

99-15027 «Coin Ret Box)

99-15030 a (Lockout Flap)

(Sw Adjuster)

99-15029 (Bracket)

99-15042 (Switch)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, GA, This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the draw. ing or any design or technical information shown thereon, Nor any ‘right to reproduce this drawing or any part thereo!. Except for manufacture by vendors of Atari, Inc., and for manutactute under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof! unless by written agreement with or written permission from the corporation, e &h 99-15040 (Lever)

99-15054 (Pivot for Lever)

~~ 9915028 (Coin Ret. Box}

99-15056 (Screw for Bezel) 99-15060

aa (Sw. Cover)

Figure 3-6 Vertical-Mounted Coin Door A037619-xx B

3-14

Page 49

99-15067 (Lock Assy.)

99-15063 (Screw)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe: 99-15067 (Lock Assy.)

99-15036 (Cover)

Gific written permission of Atari, Inc., Sunnyvale, CA. This, ‘drawing is only conditionaly issued, and neither receipt nor possession thereof confers or transfers any right in, oF Ii Cense {o use, the subject matter of the drawing or any de- Sign or technical information shown thereon, nor any right to-reproduce this drawing or any part thereo!. Except for manufacture by vendors of Atar, Inc., and for manulacture under ihe corporation's written license, no right is granteg to reproduce this drawing or the subject matter thereo!, un less by written agreement with or written permission from the corporation.

A037619-01 — U.S. 25¢/25¢ Coin Door A037619-02 — U.S. 50e/50¢ Coin Door 4037619-03 — Canadian 25¢/25¢ Coin Door ‘A037619-04 — British 10 P/10 P Coin Door ‘A037619.05 — British 10 P/50 P Coin Door A037619-06 — British 20 P/50 P Coin Door ‘403761907 — Australian 20¢/20¢ Coin Door ‘A037619-08 — German 1 DM/1 DM Coin Door ‘4037619-09 — German 2 DM/1 DM Coin Door ‘A037619-10 — German 2 DM/5 DM Coin Door A037619-11 — German 1 DM/5 DM Coin Door A037619-12 — 5 FriS Fr Coin Door ‘A037619-13 — Swiss 1 Fr/1 Fr Coin Door A037619-14 — French 1 Fr/1 Fr Coin Door 99-15038 (Beze! tor Button)

99-18001 thru 99-15012 (Ret. Button)

99-15052 (Spring for Button)

99-15065 (Clamp)

99-15039 (Bezel for Cover)

99-1506 (Screw)

A037619-15 — French 2 Fri1 Fr Coin Door A037619-16 — Swedish 1 Kr/1 Kr Coin Door ‘A037619-17 — Spanish 25 Pisi25 Pts Coin Door A037619-18 — Italian 100 L/100 L Coin Door ‘A037619-19 — Hong Kong $1/$1 Goin Door ‘A037619-20 — Japanese 100Y/100¥ Coin Door

Figure 3-6 Vertical-Mounted Coin Door, continued A037619-xx B

3-15

Page 50

‘Space Duel™

Figure 3-6 Vertical-Mounted Coin Door, continued Parts List

Part No. Description A037491-01 Coin Box (not shown in illustration)

A037542-01 Harness Assembly

70-10-40 6.3V Miniature Screw Base Incandescent Lamp 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Piate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Piate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055, Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15062 Hinge 99-15063 Screw for Hinge 99-15065 Clamp for Frame 99-15066 Screw for Clamp 99-15067 Lock Assembly

3-16

Page 51

A— warninc —&

Prior to removing or repairing any printedcircuit board, unplug the game and open the table top. Let the Regulator Audio II PCB heat sink cool down for 10 minutes.

To Remove Printed-Circuit Board:

  • Open the Upright cabinet rear access panel or Cocktail cabinet table top.
  • Locate the hardware that secures the PCB to the cabinet, and remove this hardware. (Each PCB has one screw and two spacers to secure it.)
  • If you are removing the game board, first remove the tie wraps that fasten the edge connectors to the game PCB. Then unplug the edge connectors on the game PCB. If you are removing the Regulator/Audio II PCB, disconnect the five small harness connectors on this board.
  • Carefully slide the PCB straight out of its slots. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required.

Figure 3-7 ‘Space Duel™

@ Reinstall the PCB, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, so if they don't slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty.

® Replace the hardware that secures the PCB to the cabinet wall. Reinstall the fasteners used to secure the edge connectors to the PCB. Close and lock the rear access panel or table top.

@ Check that the operation of the game is correct by performing the self-test. This is especially important with any game when you repair a PCB. Normally the only adjustments on this game are option switch changes (made on the 8-toggle DIP switch). Unless you are a qualified technician, do not turn any of the knobs near the game PCB’s edge connector. Also do not turn the small knobs on the Regulator/Audio Il PCB.

GAME PCB

REGULATOR = ie AUDIO Il PCB TS

Disassemble in the order indicated. (Circled numbers match the steps above.)

Printed-Circuit Board Removal

3-17

Page 52

Space Duei™

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

A Figure 3-8 Space Duel™ Game PCB Assembly A036837-01 and -02

3-18

Page 53

Figure 3-8 Space Duel™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

0012294-01 Audio 1/0 N-Channel MOS/LS! Custom Chip (B83, C/D3)

19-31510310K Ohm Vertical PCB-Mounting Cermet Trimpot(R189, 190, 213, 214) Acceptable substitute

is part no. 119002-103.

19-315201200 Ohm Vertical PCB-Mounting Cermet Trimpot(R99, 100) Acceptable substitute is part no.

119002-201.

19-3152022K Ohm Vertical PCB-Mounting Cermet Trimpot(R188, 211)Acceptable substitute is part no.

119002-202.

21-101103.01 pf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor(For -02 PCB assy. only: C66)

21-101153. 015 pf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C133, 134) 24-350107 100 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C119, 121, 122)

24-5001051 yf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C123)
24-50010610 yf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C20, 34, 35, 37)
24-50047647 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C16)

27-102182 .0018 yf, + 10%, Radial-Lead Ceramic-Disc 1000V Capacitor (For -01 PCB assy. only: C77. For -02 PCB assy. only: C72) 29-006 1 uf, + 10%, 35V Tantalum Capacitor (C108) 29-088. -1 pf Ceramic-Disc 25V Radial-Lead Capacitor (C1-15, 17-19, 21, 22, 25, 26, 29, 33, 36, 38-41, 43-58, 68-70, 79-82, 84-106, 111, 112, 114-118, 124-126, 130-132, Also, for 01 PCB assy. only: C60, 61, 64, 76. For -02 PCB assy. only: C59, 65. 67, 71)

31-1N100100V Type-1N100 Switching Diode(CR1, 2, 6, 7)
31-1N91475V Type-1N914 Switching Diode(CR3, 4)

33-2N3906 Type-2N3906 PCB Switching and Amplifying Transistor (Q7, 11)

34-2N3904 Type-2N3904 NPN 60V 1-Watt Transistor (Q1, 5, 6, 8-10, 12) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q2, 3, 4)

37-TLO82CPType-TL082 Integrated Circuit{A10, D10, D/E11, D/E12, R8)
37-555Type-555 Integrated Circuit(A4)
37-1495Type-MC14965L Integrated Circuit(A/B11, A/B12, C11, C12)
37-7433Type-7433 Integrated Circuit(L10)
37-13201Type-LF13201 Integrated Circuit(B10, E10)
37-74193Type-74193 Integrated Circuit(E4)
37-LM324Type-LM324 Integrated Circuit(B5, DS)
37-74LS00Type-74LS00 Integrated Circuit(E3, L3)
37-74LS02Type-74LS02 Integrated Circuit(H3, K5, NS)
37-74LS04Type-74L.S04 Integrated Circuit{J3, K9)
37-74LS08Type-74LS08 Integrated Circuit(L6, R3)
37-74LS10Type-74LS10 Integrated Circuit(K4)
37-74LS14Type-74LS14 Integrated Circuit(F7)
37-74LS20Type-74LS20 Integrated Circuit(H5)
37-74LS27Type-74LS27 Integrated Circuit(M4)
37-74LS32Type-74LS32 Integrated Circuit(J6, M5, N3)

37-74LS42 Type-74LS42 Integrated Circuit (H7, L4, P3, R2)

37-74LS74Type-74LS74 Integrated Circuit(A7, K3, L5)
37-74LS109Type-74LS109 Integrated Circuit(E5)
37-74LS139Type-74LS139 Integrated Circuit(K6)
37-74LS157Type-74LS157 Integrated Circuit(F6, K8, L8, M8, N8)
37-74LS161Type-74LS161 integrated Circuit(J4, M6, N6, P6, R6)
37-74LS164Type-74LS 164 Integrated Circuit(M3)
37-74LS174Type-74LS174 Integrated Circuit(P2, R4)
37-74LS175Type-74LS175 integrated Circuit(C6, D6, D7, E6, H6, K2, K10)

{Continued on next page]

3-19

Page 54

Space Duel \™

Figure 3-8 Space Duel™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Boid)

37-74LS191 Type-74LS191 Integrated Circuit (C7) 37-74LS194 Type-74LS194 Integrated Circuit (A8, B8, C8, F8, H8, J8) 37-74LS244 Type-74LS244 Integrated Circuit (B1, C1, E2, H2, M9) 37-74LS245 Type-74LS245 Integrated Circuit (F2, P8)

37-74LS251 Type-74LS251 Integrated Circuit (L9, N9) 37-74LS273 Type-74LS273 Integrated Circuit (R9) 37-74LS374 Type-74LS374 Integrated Circuit (J2) 37-74LS393 Type-74LS393 Integrated Circuit (F4, H4)

37-74S00 Type-74S00 Integrated Circuit (E7) 37-74S802 Type-74S02 Integrated Circuit (B7) 37-74804 Type-74S04 Integrated Circuit (F3) 37-74S874 Type-74S74 Integrated Circuit (A6) 37-74S260 Type-74S260 Integrated Circuit (J5) 37-7815 +15V Voltage Regulator (VR2) 37-7915 — 15V Voltage Regulator (VR1) 38-MV5053 Type-MV5053 Light-Emitting Diode (CR5)

41-3003 100 pH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (L1, 2,3) Acceptable substitute is part no. 141002-001. 62-001 SPST Momentary Pushbutton Switch (Reset) 66-114P1T 4-Station Single-Throw, Dual-Inline-Package Bit Switch (P10) 66-118P1T 8-Station SingleThrow, Dual-Inline-Package Bit Switch (B4, D4) 72-6610S #6 x %-Inch Phillips-Head Screw (for mounting PCB to cabinet wall) 75-07017 Spacer for Mounting Printed Circuit Board 78-24012 5-Inch Beaded Nylon Tie Wrap (for PCB edge connectors) 79-42C22 22-Contact Medium-Insertion-Force Integrated Circuit Socket (M2) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (J1, K/L1, M1, N/P1, N/P7, R1, R7) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (B3, C2, C/D3, J9) 81-4302 Nylon Snap-In Fastener 90-6013 Microprocessor (C2) 90-7033 Random-Access Memory (E1, H1, J7, K7, L7, M7) 034536-02 Cocktail Foam Vibration Damper 034536-03 Foam Vibration Damper 035745-02 18-Inch Plastic PCB Retainer 110000-101 100 Ohm, +5%, %W Resistor (R91, 92) 110000-102 1K Ohm, +5%, %4W Resistor (R19, 22, 46, 50, 56, 72, 83, 108, 117-119, 123-128, 135-142, 154-158, 164, 167, 171, 183, 205, 221) 110000-103 10K Ohm, +5%, %4W Resistor (R1-18, 20, 21, 23-40, 45, 59, 62-69, 73, 107, 151-153, 176, 180, 200, 203, 215-220. Also, for -01 PCB assy. only: 87, 93, 94.) 110000-104 100K Ohm, +5%, %4W Resistor (R44, 49) 110000-105 1M Ohm, +5%, %W Resistor (R42, 43, 47) 110000-122 1.2K Ohm, +5%, 4W Resistor (R60, 193) 110000-151 150 Ohm, +5%, %W Resistor (R120) 110000-153. 15K Ohm, +5%, %W Resistor (R109, 165) 110000-221 220 Ohm, +5%, YW Resistor (R41, 74, 121, 122) 110000-222 2.2K Ohm, +5%, %W Resistor (R58, 174, 175, 177, 186, 196-198, 208) 110000-223 22K Ohm, +5%, ‘4W Resistor (R70, 170)

3-20 [Continued on next page]

Page 55

Figure 3-8 Space Duel™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 110000-270 27 Ohm, +5%, %W Resistor (R172) 110000-272 2.7K Ohm, +5%, %4W Resistor (R182, 206) 110000-332 3.3K Ohm, +5%, YW Resistor (R51, 53-55) 110000-392 3.9K Ohm, +5%, %4W Resistor (R48, 52, 61, 179, 184, 187, 202, 207, 209) 110000-471 470 Ohm, +5%, 14W Resistor (R113, 114, 129-134, 143-150, 159-163, 166, 169, 173, 178, 185, 194, 199, 201, 210) 110000-472 4.7K Ohm, +5%, VaW Resistor (R57) 110000-561 560 Ohm, +5%, %W Resistor (R112) 110000-562 5.6K Ohm, +5%, %4W Resistor (R191, 212) 110000-680 68 Ohm, +5%, %4W Resistor (R168) 110000-681 680 Ohm, +5%, %4W Resistor (R181, 204. Also, for -02 PCB assy. only: R84.) 110000-683 68K Ohm, +5%, YW Resistor (R71) 110000-821 820 Ohm, +5%, %W Resistor (For -02 PCB assy. only: R85, 95, 96) 110001-271 270 Ohm, +5%, v2W Resistor (R195) 110003-752 7.5K Ohm, + 1%, ),W Resistor (R97, 98, 101-106, 110, 111) 110004-001 Voltage Dependent Resistor (RV1, 2) 121007-473 .047 yf, + 10%, Radial-Lead Epoxy-Dipped 50V Polycarbonate Capacitor (C75, 78) 122000-225 2.2 pf, + 10%, 35V Tantalum Capacitor (C107) 122002-102 .001 uf, Ceramic-Disc 50V Radial-Lead Capacitor (C27, 28) 122005-103 .01 yf, Ceramic-Dise 25V Radial-Lead Capacitor (C42) 122008-224 .22 uf, Ceramic-Disc 25V Radial-Lead Capacitor (C30-32) 128002-100 10 pf Radiai-Lead Epoxy-Dipped 100V Mica Capacitor (C83) 128002-101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C23, 135) 128002-151 150 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C110) 128002-221 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C120) 128002.390 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C24, 109, 113, 128) 131002-001 6.8V, 400 mW, +5%, Zener Diode (CR8) 136002-125 Programmable Read-Only Memory (N4) 136006-102 Programmable Read-Only Memory (N/P1) 136006-103 Programmable Read-Only Memory (M1) 136006-104 Programmable Read-Only Memory (K/L1) 136006-105 Programmable Read-Only Memory (v1) 136006-106 Programmable Read-Only Memory (R7) 136006-107 Programmable Read-Only Memory (N/P7) 136006-201 Programmable Read-Only Memory (R1) 137002-001 Type-74S86 Integrated Circuit (B6) 137149-001 Type-74LS11 Integrated Circuit (F5) 137 158-002 Type-AM6012PC 12-Bit Digital-to-Anaiog Converter (For -02 PCB assy. only: A/B9, F9) 137 160-003 Type-MC3410 10-Bit Digital-to-Analog Converter (For -01 PCB assy. only: C9, E9) 137161-001 Read-Only Mernory (M2) Note: /f you replace this part, you must erase this ROM before locking up the game. See Self-Test Procedure. in this manual for instructions. if you do not erase the ROM, the Self-test will show the ROM to be “defective” by displaying the etter E on the screen. 137 179-001 Address Controller (J9) 144000-001 12.096 MHz, + .005%, Crystal (¥1) 179051-001 Test Point Acceptable substitute is part no. 020670-01,

3-21

Page 56

a

An 4 > mS Rea10 TW ° Se :

TDAZ002 A ToAzoCeA \acoz Q5 a7 ~ TT

C7 Gea*BScco
0|. oCcs
}orEee]RzZelcla
Risk220]Rei,aw
qlczyk
Rie.Sn270

Oo} ae CER’

cece=ard]
4eeGIR!
iBhos

3 = RN Riot 354, c+ S | [|

  • 0 {220} 35" R30 RO aw zt cry CFinaooz =f} Q 0 a 3360 F NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spect fic written permission of Atat, Inc., Sunnwale, CA, This draw: ing is only conditionally 1ssued, and neither receipt nor pos: Session thereo! confers or transfers any right in, or hcense to use. the subject matter of the drawing or any design of tech: Nical infcrmation shown thereon, nor any right to reproduce this drawing or any part thereot. ‘Except for manufacture by venders of Atari, Inc., and for manufacture under the corpor ation’s written license, no right is granted to reproduce this Grawing or the subject matter thereof. unless by written agreement with or written permission /rom the Corporation

Figure 3-9 Regulator/Audio Il PCB Assembly A035435-04

3-22

Page 57

Figure 3-9 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold) 12-52P7 2.7 Ohm, +5%, 1W Resistor (R5) 19-100P1015 -1 Ohm, +3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250108 1000 pf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350338 3300 pf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19) 29-088 -1 uf Ceramic-Disc 25V Radiai-Lead Capacitor (C3, 11, 20, 21) 31-1N4002 100V 1-Amp. Silicon Rectifier Type 1N4002 Diode (CRI, 4) 31-1N5401 100V 3-Amp. Silicon Rectifier Type 1N5401 Diode (CR5-8) 33-TIP32 PNP Power Transistor, Type TIP32 (Q2) 34-2N3055 NPN Silicon Transistor, Type 2N3055 (Q3) 37-LM305 5V Linear Voltage Regulator (Qi) 72-1608C, #632 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw (Q3) 72-6606S #6 x 3,-Inch Pan-Head Thread-Forming Cross-Recessed Type-AB Zinc-Plated-Steel Screw (Q5, 7) 72-6610S #6 x %-Inch Phillips-head Screw (attaches PCB to cadinet wall) 75-07017 Spacer for Mounting Printed Circuit Board (2 required) 75-F60405, #6-32 x ‘%4-Inch Binder-Head Nylon Screw (Q2) 75-99516 #6-32 Nut/Washer Assembly (Q3) 78-16008 Thermally Conductive Compound (Q3) 78-16014 Thermally Conductive Silicon Insulator (Q2) 79-58306 6-Position Connector Receptacle (J6, 9) 79-58308 9-Position Connector Receptacle (J7) 79-58346 12-Position Connector Receptacle (J10) 79-58354 4-Position Connector Receptacle (J8) 020670-01 Test Point 034531-01 Heat Sink 034536-02 Foam Vibration Damper 034536-03 Cocktail Foam Vibration Damper 035745-06 5-Inch Plastic Cocktail PCB Retainer 100015-103 .01 pf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) 110000-010 1. Ohm, +5%, YW Resistor (R10, 19) 116000-100 10 Ohm, +5%, %W Resistor (R11, 20, 29, 30) 110000-101 100 Ohm, +5%, “W Resistor (R4, 12, 22) 110000-102 1K Ohm, +5%, 4W Resistor (R27, 28) 110000-103 40K Ohm, +5%, ‘4W Resistor (R13, 14) 110000-271 270 Ohm, +5%, YW Resistor (R1) 110000-330 33 Ohm, +5%, %4W Resistor (R3) 110000-392 3.9K Ohm, +5%, ¥4W Resistor (R6) 110000-562 5.6K Ohm, +5%, MW Resistor (R32, 33) 110000-752 7.5K Ohm, +5%, “4W Resistor (R7)

110001-221 220 Ohm, +5%, v2W Resistor (R9, 21) 122002-102 .001 pf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C2, 7, 16) 122004-224 .22 uf Ceramic-Disc 25V Capacitor (C6, 8, 15, 17) 137151-002 Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q5, 7)

3-23

Page 58

Space Duel/™

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific walten permission of Atari, Inc., Sunnyvale, CA, This drawing 's only conditionally’ issued, and neither receipt nor Possession thereo! conters or transters any right 1n, or license to use, the subject matter of the drawing for any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereo!. Ex: cept for manulacture by vendors of Atari. Inc., and for manufacture under the corporation's written license, no right 10 reproduce this drawing is granted or ne subject matter thereot unless by written agreement wilh or written permission Irom the corporation A037395-01 i (Transformer Assy)

‘A037395-02 : iranstormer assy) Ef

A021084-xx (Volt. Plugs) 29.053 (Capacitor) ~, N= t 634544-01 (Fuse Block Cur.)

79-4411001 (Fuse Post)

46-2017002 (Fuse)

034482.02 “4 (Chassis) 78-70501SC

A035891-01 (Fuse Harness)

46-301203 (Fuse)

037639-01 (Label)

78-2708 (Bushing)

A034630-01 79-3206 (Filter Assy.) (Fuse Block) eh 46-2014002 “ (Fuses)

79-15021001 A035890-01 (Term. Block) \ (Pwr. Harness) A034629-01 3A-MDA3501 (A.C. Harn.) (Rectifier)

Figure 3-10 Color XY Power Supply Assemblies A037396-xx B and A037875-xx B

3-24

Page 59

Figure 3-10 Color X-Y Power Supply Assemblies Parts List

Part No. Description (Reference Designations in Bold)

A021084.01Voltage Plug for 100V(violet)
A021084-02Voltage Plug for 120V(yellow)
A021084-04Voltage Plug for 220V(blue)
A021084-05Voltage Plug for 240V(brown)

A034629-01 A.C. Harness Assembly

A034630-01RFI Filter Assembly(FL1)

A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly

A037395-01Upright Transformer Assembly(11)
A037395-02Cocktail Transformer Assembly(11)

29-053 27,000 uf 15 VDC Electrolytic Capacitor (C1)

3A-MDA3501Bridge Rectifier, type MDA 3501(CR1)

46-2014002 4-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F2, F4-F6) 46-2017002 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-301203 20-Amp. 32V 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x “%,-Inch Outside Diameter x Ya-Inch Thick

78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post

03448202 Power Suppiy Chassis 034544.01 Fuse Block Cover 037243-01 Metal Base Plate (not shown in iliustration)

037639-01Label for Fuse Value(F1)

037641-01 Label for Fuse Values (F2~F6) 037836-01 Metal Shield for Cocktail Power Supply (not shown /n illustration)

NOTE: A037396.01 and A037875-01 power supply assemblies have 120V plug A037396-02 and A037875-02 have the 100V, 220V and 240V plugs A037396-03 and A037875-03 have the 220V and 240V plugs

Line Voltage Range 90-110 VAC (100) 105-135 VAC (120) 100-140 VAC (220) 220-260 VAC (240) Voltage Selection Plug Wire Color Violet Yettow* Blue Brown “This is the only plug provided on the North American power supply.

3-25

Page 60

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 61

1st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of game manuals. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATAR! games products, or are requesting additional publications, we wil! immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm O Distributor

Address. CI Operator City State Zip 5 Other__ Area Code Phone

Page 62

First told

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary it mailed in the United States

Second fold

Page 63

Z

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant, and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including !abor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the foan, without written consent of Atari, Inc. ES RES RES RE BE EK RS Oe 2H : :

: : : :

Page 64

ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086, 408/74! LEX 35-7488 O-