CATHODE RAY TOMES

Death Race

Death Race (Exidy, 1976) · Manual · 19 pages · 22 sections · original scan

Page 1

MANUAL

Page 2

Wi.

IV.

VI.

VII. TABLE OF CONTENTS

GENERAL INFORMATION

OBJECT OF THE GAME

NORMAL OPERATION

SYSTEM FUNCTIONAL DESCRIPTION

Power Supply Logic Printed Circuit Board (PCB) Coin Mechanism Start Switch Steering Units Pedal Units Speakers T.V. Monitor Shift Lever

TROUBLESHOOTING TIPS

Picture not present Entire picture scrambled Picture present but vartially bad or characters act incorrectly Bad Steering No shift No acceleration or bad acceleration No game start/sound present. No game start/sound not present Game starts/no sound ADJUSTMEN?S

Tower Supply Adjustment. Volume Adjustment Tone Adjustment Game Time Adjustments FIGURES

Figure 1 — Main Cabinet (Exploded View) Figure 2. — Steering Box and Display (Exploded View) Figure 3 — Foot Pedal Assembly (Rear View) Figure 4 — Power Supply Figure 5 — Optical (Steering) Board Figure 6 — Logic Printed Circuit Board (PCB) Figure 7 — System Block Diagram Figure 8 — Wiring Diagram Figure 9 — Acceleration (Foot Pedal) Wiring Figure 10 — Optical Steering Board Schematic Figure 11 — Steering Mech. Detail (Exploded View) PAGE NO.

6-7 8-9

20-21

Page 3

IL

III.

Iv.

VI.

VII. TABLE OF CONTENTS

GENERAL INFORMATION

OBJECT OF THE GAME

NORMAL OPERATION

SYSTEM FUNCTIONAL DESCRIPTION

Power Supply Logic Printed Circuit Board (PCB) Coin Mechanism Start Switch Steering Units Pedal Units Speakers T.V. Monitor Shift Lever

TROUBLESHOOTING TIPS

Picture not present Entire picture scrambled Picture present but partially bad or characters act incorrectly Bad Steering No shift No acceleration or bad acceleration No game start/sound present No game start/sound not present Game starts/no sound ADJUSTMENTS

Power Supply Adjustment Volume Adjustment Tone Adjustment Game Time Adjustments FIGURES

Figure 1 — Main Cabinet (Exploded View) Figure 2. — Steering Box and Display (Exploded View) Figure 3 — Foot Pedal Assembly (Rear View) Figure 4 — Power Supply Figure 5 — Optical (Steering) Board Figure 6 — Logic Printed Circuit Board (PCB) Figure 7 — System Block Diagram Figure 8 — Wiring Diagram . Figure 9 — Acceleration (Foot Pedal) Wiring Figure 10 — Optical Steering Board Schematic Figure 11 — Steering Mech. Detail (Exploded View) PAGE NO.

6-7 8-9

20-21

Page 4

DEATH RACE

I. GENERAL INFORMATION

Death Race pits the player against an intelligent acting, evasive, running Gremlin. Unlike most “player versus machine” games, the “machine” in this case does not simply repeat an action or sequence, but actually “sees”, “thinks”, and ‘‘acts” as intelligently (and even more rapidly) than would another player. The result of this is that each game is a new and different experience.

Il. OBJECT OF THE GAME

The object of the game is simple. Hit a Gremlin and you win a point. There are two Gremlins running around the playing field in a random fashion. They are intelligent robots in every sense and will avoid all objects so long as they can see a way to escape. You drive one of two cars which are completely under your control. You can steer them anywhere in any direction within the playing field; move forward in low or high gear; and move in reverse when necessary. You can drive as ‘ast, but no faster than the Gremlins can run. When you hit a Gremlin a tombstone (cross) will appear and remain in that:same spot until the game is over and a new game begun. Wherever you hit a Gremlin on the playing field, the cross will remain. Thus, each game creates its own totally random and different maze of crosses that each player must steer through while chasing the Gremlins. The more hits, the more crosses; the more crosses, the harder the steering becomes. Thus, it becomes increasingly difficult to maneuver as your skill increases.

III. NORMAL OPERATION

The screen is divided horizontally into three (3) areas: the larger being in the middle between the dotted lines. This represents the legitimate playing field. It is only in this area that hits can occur; and any car that attempts to leave this area will crash when it contacts the top, bottom, or (dotted) side lines. There is no point given or cross created for this type of crash. Although the cars will crash when trying to cross the dotted line toward the solid sideline, the Gremlins can and do pass through without crashing. The areas on the sides between the solid and dotted lines are a designated “safe” area for the Gremlins. They will enter this area at will. When you crash your car into anything, whether it be a Gremlin, cross, or a boundary (line), your car will pause briefly before moving again, unless you immediately shift into reverse to back away from the scene of the crash. Even if you do not back away, your car will begin to move again. It is thus possible to crash into and pass through, after a pause, any boundary. Although by this method you can leave the playing field and pass into the safe zone or other “out of bounds” areas, you cannot intercept and hit a Gremlin nor receive a point outside the playing field. Once outside the playing field, you may drive your car off the visible screen and it will reappear on the opposite side of the screen. The Gremlins can do this also but should only do so if the safe zone area is blocked and there is no place for them to enter the playing field. In this case, they will normally run off the screen to the side and reappear on the opposite side. A Gremlin should never pass through the top or bottom boundaries. Should one player crash into the other player, both cars will pause briefly before proceeding. Because of this, it is sometimes advantageous to crash into your opponent’s car in order to slow down and prevent your opponent from hitting a Gremlin and scoring. There is no score from crashing into your opponent’s driven car. When one coin is inserted the sound for player one is enabled. When a second coin is inserted, the sound for player two is enabled. When the start button is depressed the game begins, the players can drive their cars.and the game counter counts down from 99 toward 00. The duration of the game is adjustable in three (3) increments from one (1) minute twenty (20) seconds, to two (2) minutes fiftten (15) seconds. See ‘““ADJUSTMENTS” for information regarding game time.

Page 5

Each car has two forward speeds. When the pedal is not depressed, the car will not move, but will turn on its axis as the steering wheel is turned. Slight depressing moves the car forward in low gear, and full depression moves the car forward in high gear. If the shift lever is in reverse, the car will move backwards at a low gear speed. There is no high gear in reverse.

IV. SYSTEM FUNCTIONAL DESCRIPTION (Refer to System Block Diagram. Fig. 7)

115 VAC power is applied through interlock switch $1 (back door panel) to the power supply, the T.V. monitor, and the light fixtures. The Power Supply converts this to +5VDC and 22 VAC. The +5VDC is used to power the LOGIC PCB (printed circuit board), Coin Counter, both steering units (optical boards). and both foot pedal units (2 microswitches each), the 22 VAC is used to power the audio (sound circuitry located on the LOGIC PCB. The Logic PCB generates all video (T.V. picture), audio (sound), and is the nerve center for all control functions. The Coin Mechanism signals the Logic PCB that a one (1) or two (2) player game can now begin, pending the pressing of the start switch. It also simultaneously signals the coin counter to advance one (1) count for each coin. The Start Switch, when depressed, signals the logic PCB that a game can now begin. The Steering Units for player 1 and player 2 are identical, and each consists of a steering wheel, a shift lever, and an optical control board. The optical control board converts the rotation of the steering wheel and the two (2) positions of the shift lever (forward & reverse) into commands which are routed to the Logic PCB, which then interprets and executes these communds. causing the driven cars on screen to react accordingly. The Pedal Units for player 1 and player 2 are identical and each consists of a spring loaded foot pedal and two (2) microswitches. The pedal, when in the ‘“‘off”’ position (not depressed) trips the top micreswitch and does not trip the bottom switch. Depressing the pedal down slightly allows both the top and bottom microswitch to be in an “‘untripped” state, which tells the Logic PCB that the corresponding player is now in low gear. Further depression of the pedal trips the bottom microswitch, telling the Logic PCB that the corresponding player is now in high gear. The image on screen will then react accordingly. The Speakers, which are located in the steering module, receive their signal directly from the Logic PCB; and are not activated until the coin mechanism has been tripped by a coin. They will remain active only while a game is in progress. When the game ends, so does the sound.

  • The Shift Lever is part of the steering units, and its signal is developed by the same optical control board as is the steering (see steering units).

V. TROUBLESHOOTING TIPS

NOTE

The single most important factor in the proper operation of your Death Race game is the power supply voltage adjustment. Before any troubleshooting can be done the power supply voltage must be checked, and adjusted if necessary. See “POWER SUPPLY ADJUSTMENT.”

PICTURE NOT PRESENT Check: 1.115 VAC system power

  • +5VDC power supply
  • All harnesses connected 4, T.V. brightness control

ENTIRE PICTURE SCRAMBLED Check:

  • T.V. horizontal hold control
  • T.V. vertical hold control 8, +5VDC power supply adjusted
Page 6

PICTURE PRESENT BUT PARTIALLY BAD, OR CHARACTERS ACT INCORRECTLY. Check:

  • +5VDC power supply adjusted
  • Nothing external touching Logic PCB
  • Harnesses all tightly connected

NO STEERING OR BAD STEERING: Check:

  • Light bulbs on optical control boards
  • +5VDC power supply
  • Optical board harness connected
  • Light bulbs on optical control boards aligned properly (See Fig. 5)
NOTE

If only one player has bad steering the optical board can be tested by plugging the player 1 connector to the player 2 optical board (and vice versa). If this method is used be extremely careful to insure the connector is not plugged in backward. Plugging the connector in backward will castroy the optical board.

NO SHIFT Check: All checks are the same as those listed under “NO STEERING OR BAD STEERING’ above.

NO ACCELERATION OR BAD ACCELERATION Check:

  • Foot pedals free to operate
  • Micro switches on foot pedals
  • Foot pedal harness connected
  • +5VDC power supply
NOTE

Tf only one player has bad acceleration the foot pedal harnesses can be reversed for checkout of microswitches if necessary, as outlined for steering problems under “NO STEERING OR BAD STEERING” above.

NO GAME START/SOUND PRESENT Check:

  • Start switch
  • +5VDC power supply
  • Start switch harness connected

NO GAME START/SOUND NOT PRESENT Check: 1, Coin Mechanism — NOTE: Coin mechanism functions okay if drop of coin causes cars to reset to start position at bottom of screen, facing upwards.

  • +5VDC power supply
  • Harnesses connected ©

GAME STARTS/NO SOUND _ Check:

  • 22 VAC from power supply
  • Speaker harnesses connected

Any problems which cannot be localized to other units probably indicate a bad LOGIC PCB, since it is the heart of the system. If another is available it should be temporarily placed in the bad game to see if the problem remains.

Page 7

VI. ADJUSTMENTS

POWER SUPPLY ADJUSTMENT

  • Contact voltmeter leads to Logic PCB as indicated in Fig. 6.
  • Adjust potentiometer R8 (see fig. 4) on power supply for +5.0 VOC as measured on the LOG- IC PCB per above diagram. The positive (+) lead of the voltmeter must ve touching the large metal area (trace) on the non-component side of the Logic PCB which is connected to pins 2 and 5 of the 6 pin connector. The negative (-) lead of the voltmeter must be touching the large metal area (trace) on the component side of the LOGIC PCB, which is connected to pins 1 and 6 of the 6 pin connector.
NOTE This voltage measurement must be made at the LOGIC PCB, since voltage losses may occur between the power supply and the Logic PCB. Adjustment of the power supply voltage made while measuring the voltage directly on the power supply terminals will not necessarily insure proper voltage to be present on the Logic PCB.

VOLUME ADJUSTMENTS (Refer to fig. 6) Volume controls are located on the Logic PCB and are as follows: 1, Player one motor R50 2, Player two motor R66

  • Crash R80 4, Scream R782

TONE ADJUSTMENTS (Refer to Fig. 6) Tone controls are located on the Logic PCB and are as follows:

  • Player one R7
  • Player two R14

SCREAM MODULATION R778 R780

GAME TIME ADJUSTMENTS (Refer to Fig. 6) A movable jumper wire, located on the LOGIC PCB, allows adjustment of the length of game time. The counter will always begin at 99 and begin to count down to 00 when the START button is depressed after a coin is inserted. The rate at which the counter counts down will vary depending on the location of the jumper wire. Three options are available for a short, medium and long game time. These are selected by placing the jumper wire on the appropriate terminal post. The post nomenclatures and approximate times are listed below:

Post 1 = 1 minute 20 seconds Unmarked Post = 1 minute 45 seconds Post 2 = 2 minutes 15 seconds

Page 8

13,14,15 rig 1 MAIN CARINET

Page 9

Figure No. 1 HANGS HORAIS Ads 15. 16. 17. 18. 19.

DR-UP-CAB

DR-FP-BOX-COMPLETE

DR-FP-BOX-EMPTY

DR-PCB-2

EAPS-5-10

DR-PCB-PS-B

2608-300 £607 DR-CB DR-CB-LH DR-FP-C XM701-10 £64-30A 17412 F20T12CW $120TS

DR-MON-BRK7

Cabinet Foot pedal box comp Foot pedal box empty Game printed circuit board

Power supply Power supply & P.C.B. box

Coin mech Coin counter Coin bucket Coin box lid & hasp Foot pedal box cover

Monitor Interiock switch Fuse holder Fuse AC cord Fluorescent bulb Fluorescent fixture Monitor brkt.

Page 10

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 11

Figure No. 2 EXxXIDY

DR-PLEX-17” Plex panel destruction derby DR-PLEX-19%” Plex panel frame 23” BEZEL Bezel T936-DI-BLK. Start switch 4” SPKR.-GRL. Speaker grill 4 SPKR. Speaker DR-ST-BOX-COMP. Steering box complete DR-ST-BOX-EMPTY~” Steering box (less P.C.B.’s & harness) 82-2111 Steering wheel DR-ST-ASSY Steering Assy. 1. 2. 3. 4. 5. 6. 7. 8. 9. 0.

Page 12

Figure No. 3

PART NO. DESCRIPTION

E51-50R -Foot pedal micro switch DR-FP-SPRING Foot pedal spring

1 ~

Page 13

|_rrem | PART NO. Loa | EAPS-5-10

Page 14

Figure No. 5

DESCRIPTION

DR-OCB-ST Steering P.C.B. 1847 BULB Twist lock bulb E51-50R Micro Switch

NOTE:

The Filament of the light bulb on optical contro! boards (steering boards) must be properly aligned. The bulb (over transistors marked “‘A“;-B’) must be directly between and over (in line with) both transistors. Failure to align bulb properly will result in faulty or intermittent steering. Alginment should be initially correct from factory.

Page 15

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 16

AdIeV 1D OL NMOHS SGNNOXD 2 4INN 1 LINA

MIOII_N ZYmdS | Yds SYNLXIS LHOIT OL

Y3LNNOD

NIOD

@d 31907

m) = = mh) m m “SNOILINN4 1V2ID01 2

ONIWSSLS ONI: 310N 3351S

WVYOVIC 19018 WALSAS Ya 42314

Page 17

Fic 8

DR. WIRING DIAGRAM

R SPE.

L STEER. [sre | R

AK STEER

12 345Ju5 J8P8 I

[oie Wash eT

aay v1 fm) =n]

L. FOOT L. FOOT R. FOOT

PEDAL PEDAL. PEDAL

R. FOOT

[LUT

Cowar oua WW nt =NM SOR OD 10} Tv PION 3/3 iO AH nS

FUSE

UT 5 7 (PWR. SUPP) XFORMER 2 z

Page 18

Figure No. 8 J1 (PIN 1) J13 (PIN 2) P3 (PIN 11) Left speaker J7 (PIN 7) P10 (PIN 3) J1 (PIN 2) J13 (PIN 1) P3 (PIN 10) Left speaker J7 (PIN 10) P10 (PIN 2) J1 (PIN 3) J13 (PIN 7) P3 (PIN 13) Right speaker J7 (PIN 9) P10 (PIN 1) J1 (PIN 4) J13 (PIN 8J P3 (PIN 12) Right speaker J4 (PIN 2) Start J1 (PIN 5) J13 (PIN 9) P3 (PIN 9) Start J4 (PIN 1) J5 (PIN 1) J1 (PIN 6)! PQ (PIN 1) P3 (PIN 14) J8 (PIN 1) P3 (PIN 1) J8 (PIN 3) J2 (PIN 2): J3 (PIN 11) P3 (PIN 5) J4 (PIN 4) P3 (PIN 2) J8 (PIN 2) J2 (PIN 3) : J3 (PIN 10) P3 (PIN 4) J4 (PIN 3) P8 (PIN 3) +5 V Coin counter J2 (PIN 4) J3 (PIN 13) P8 (PIN 1) Coin counter P8 (PIN 2) Ground coin mech.

J2 (PIN 5) J3 (PIN 12) P6 (PIN 4) Foot pedal P11 (PIN 1) Light J3 (PIN 9) J2 (PIN 6) P6 (PIN 3) Foot pedal P11 (PIN 1) Light J3 (PIN14) J2 (PIN 7) P3 (PIN 3) J4 (PIN 5) P11 (PIN 2) Light J2 (PIN 9) J3 (PIN 5) P3 (PIN 8) J5 (PIN 4) P11 (PIN 2) Light J2 (PIN 10) J3 (PIN 4) P3 (PIN 7) J5 (PIN 3) P11 (PIN 3) Light w safety ground

J2 (PIN 11) J6 (PIN 4) P6 (PIN 6) Foot pedal P11 (PIN 3) Light w safety ground

J2 (PIN 12) J6 (PIN 3) P6 (PIN 5) Foot peda! J12 (PIN 1) N.O. inter. switch J2 (PIN 13) J3 (PIN 3) P3 (PIN 6) J5 (PIN 5) J12 (PIN 2) To power cord J2 (PIN 14) J3 (PIN 8) P13 (PIN 5) + Out sense J12 (PIN 3) To power cord J2 (PIN 15) J3 (PIN 7) P13 (PIN 6) - Sense PWR cord 5 AMP fuse J2 (PIN 16) J6 (PIN 6) P13 (PIN 3) + Sense 5A AMP fuse Com. inter switch J2 (PIN 17) J6 (PIN 5) P13 (PIN 4) - Out J10 (PIN 1) J11 (PIN 1) J2 (PIN 18) J3 (PIN 6) J13 (PIN 5) J3 (PIN 1) J10 (PIN 2) J11 (PIN 2) J7 (PIN 1) J2 (PIN 20) J13 (PIN 6) J3 (PIN 2) J10 (PIN 3) J11 (PIN 3) J2 (PIN 21) J7 PIN 2) J13 (PIN 3) J6 (PIN 1) J12 (PIN 3) Safety ground P13 (PIN 2) - Sense (P.S.) J13 (PIN 4) J6 (PIN 2) J12 (PIN 2) =2 of xformer P13 (PIN 1) + Sense (P.S.) J13 (PIN 4) J6 (PIN 2) J12 (PIN 1) =3 of xformer P13 (PIN 7) #5 of xformer P3 (PIN 1} J4 (PIN 1) J17 (PIN 3) P12 (PIN 3) P13 (PIN 8) #7 of xformer P3 (FIN 2) J4 (PIN 2) J11 (PIN 2) P12 (PIN 2) P13 (PIN 9) + Out P6 (PIN 1) Foot pedal J11 (PIN 1) P12 (PIN 1)

JQ (PIN 1) - Out P6 (PIN 2) Foot pedal

Page 19

rics

ACCELERATION (FOOT PEDAL) WIRING

GRN.

N.C Noto REQ sy LO nos ‘ WEL Gag 1

a | W/YEL. YEL.

RED RED

W/BLY. —GASO: GRAY GAS O

: Ls

Ww COM Oy; | lnc OP

NO: GND. GND. +5V GAS 1

NC, NC.

RIGHT FECAL LEFT FECAL

REAR VIEW