Gauntlet II CO-284-07 1st Printing Four Player Conversion
Four-Player Gauntlet II (Atari Games Corporation) · Change Order · 9 pages · 9 sections · original scan
€O-284-07 Ast printing
Conversion Instructions for the Four-Player Gauntlet IT
- Control panel, Atari part number A04338601 © Speaker grille, Atari part number 043348-01
- Game PCB, Atari part number A043201-21 After retrofitting these three parts in ‘shop, you will need to make only one t ee Baise for approxi- 15 minutes to i them. This method guaranthere will be little interference with traffic at the ee ee rome OC Dig oveenion prseataes, you el nee refer to the Gauntlet .
Game Play
Gauntlet Il incorporates all of the exceptional player features of the original Gauntlet. In addition to over 100 new maze layouts, many : features have been in-
Players will especially like the additional game play objective of Gauntlet II's Secret Rooms. By completing a
permanent potions and food. (For example, might be collecting all treasure and exiting within 20 seconds). ‘There are also several new features and hidden strategies to be found in each maze. The player must make more tactical decisions because Gauntlet II provides more
aati of taby ced ede hig ager
hint on how to find the Secret A eae
Atari Games Corporation * P.O. Box 361110 ® Milpitas, CA 95035 * (408) 434-3700 a
several new potions to collect. Invulnerability, repulsiveness, reflective shots, super shots, and transportability are among the new special temporary abilities. Experience will tell the player which potions provide the greatest advantage; some potions might not be beneficial depending on the game play situation. Anew feature that players especially like is being able to select their favorite hero. In Gauntlet II, a player can now choose his favorite original Gauntlet character such as Thor the Warrior, Thyra the Valkyrie, Merlin the Wizard, or Questor the Elf—even if that hero is already in play, The four characters are color-coded so there can be as many as four Warriors, for example, in play at the same time. If four Warriors were in play, one would be red, another blue, another yellow, and the remaining one would be green.
Gauntlet II Player Quest Contest (U.S. and Canada Only) Atari Games is sponsoring a player contest that is built into every Gauntlet II game shipped within the U.S. and Canada. Called the Gauntlet II Player Quest, the contest requires minimal effort on the part of operators and locations. Atari will be awarding significant prizes in an effort to build further player interest in Gauntlet II and to give locations a competitive advantage for promoting the contest. A promotion packet is included in all Gauntlet II kits and games shipped within the U.S, and Canada. Refer to the entry forms included in the promotion packet for the specific terms of the contest.
Kit Parts Inventory The assembly and part numbers listed in Table 1 are included in the Gauntlet Il Conversion Kit. Refer to Chapter 5, Illustrated Parts Lists, in the Gauntlet Operators Manual for a description of the component parts comprising the control panel assembly and the game PCB assembly. Four-Player Gauntlet II
Table 1 Kit Parts A043755-01
| Part No. | Quantity | Description |
| A043761-01 | 1 | IC Kit |
| 038158-01 | 1 | Product Identification Label |
| 041508-01 | 16 | Joystick Leaf Switch |
| 043757-01 | 1 | Conwol Panel Decal |
| 043758-01 | 1 | Speaker Grille Decal |
| 043759-01 | 1 | Display Sign |
| 043760-01 | 1 | Front Panel Decal |
| 160013-002 | 4 | Cross-Bar Leaf Switch with |
Button Holder
| CO-284-07 | a | Conversion Instructions for |
Four-Player Gauntlet II
| 043756-01 | 1 | Contest Marquee (U.S. and |
Canada only)
| 043798-01 | 1 | Contest Poster (U.S. and |
Canada only)
| €O-284-08 | 25 | Contest Entry Form (U.S. |
and Canada only)
| €0-284.09 | 10 | Player Tips Sheet |
| CO-284-10 | 1 | Contest Cover Letter (U.S. |
and Canada only)
Tools Required The only tools required to perform a complete Gauntlet II conversion are: chip extractor tool, Phillips screwdriver, 3/8-inch wrench, 15/16-inch wrench, 5/64-inch hex wrench, 1/8-inch hex driver, #10 Torx driver or other appropriate tool, heat gun, X-ACTO® knife, isopropyl alcohol, and black marker.
Conversion Instructions
A WARNING A To avoid electrical shock, unplug the game before performing the conversion procedures.
The following procedures are arranged in the sequence recommended for performing the game conversion. The parts of your cabinet that are affected by the conversion.
Four-Player Gauntlet It
are removed or cleaned first, and then the new Gauntlet Ikit parts are installed.
Replace the Joystick Leaf Leaf Switches
Switches and the Fire Button
Due to the heavy use of these leaf switches, we strongly recommend that you replace all the joystick switches and
pS ene hy ee pe ee = an ER Sere eee pl at the Gauntlet Operators Manual, Reoe fs Rp etch a cs wah 4-5 in the Gauntlet Operators Manual, Removing the Joystick Leaf Switches.
Install the Control Panel Decal
- Perform steps 1-5 of the preceding section, Replace the Joystick Leaf Switches and the Fire Button Leaf
- Doinoe remaer taereamoiioa ee the edges of the control panel. 4, Usinga black marker, mark the control panel along the edge of the T-molding where the Gauntlet II decal does not cover the existing decal, bo eae a ane and remove a of protective backing from the switch holes near ee eee
- Remove the protective backing from one end of the ae
holes in the control panel. Then the center of the decal onto the control panel. i Then using the palm of your hand, rub the decal from
the center the edge of oe ae
sy
Joell ie esker Cele Ds ea moved before af the Gauntlet II decal. However, if K warped or cut, the decal should be removed. Perform the to. install the
- Using a 1/8-inch hex driver, remove the three screws on top and the two screws on the front of the speaker grille panel, Then remove the panel.
- ee eee eae one eee cloth moistened with isopropyl alcohol (or other ap-
using the palm of your hand, rub the decal from the center toward the edge of the speaker panel.
- bs Nila ia ce em
- Reinstall the the cabinet, then por comes ape the front of the panel.
Conversion Instructions
Perform the following procedure to install the existing speaker grille decal if it is warped or cut.
- Using a heat gun or hair dryer, directly heat the existing speaker grille decal, not the metal. Do not melt the decal. (The decal can be removed without heating, but with more difficulty.)
- While applying heat, grasp the corners of the decal and peel it from the panel.
- Perform steps 3 through 5 of the preceding speaker grille decal instructions.
Install the Front Panel Decal The existing front panel decal does not have to be removed before applying the Gauntlet II decal. Perform the following procedure to install the new front panel decal.
- Clean the existing front panel decal with a lint-free cloth moistened with isopropyl alcohol (or other appropriate cleaner).
- Remove the protective backing from one end of the decal. Carefully position the Gauntlet II front panel decal so that the decal is aligned with the top center edge of the existing decal. Then press the center of the decal onto the panel.
- Using the palm of your hand, rub the decal from the center toward one edge of the front panel. Repeat for the opposite edge of the decal.
IC Kit Anew set of 19 integrated circuits (ICs) has been designed for your Gauntlet Il Game PCB. Table 2 lists the ICs and their Game PCB locations for the U.S., German, and Japanese kits.
Location of Replacement ICs The Game PCB Assembly showing the location of each IC to be replaced or added is included in this manual. (See Figure 1.) Each IC is marked with the letter A or R. A represents an EPROM to be added. R represents an EPROM to be replaced Four-Player Gauntlet II
Table 2 Integrated Circuits in Four- Player Gauntlet II Conversion Kit a) f Basic Set of ICs: Designator Description Part No.
| 1A | 300 ns EPROM Integrated Circuit | 136043-11119X | |
| 1c | 300 ns EPROM Integrated Circuit | 136043-11236 | |
| IL | 300 ns EPROM Integrated Circuit | 136043-11134@ | |
| IP | 300 ns EPROM Integrated Circuit | 136043-1124 5x, | |
| 2A | 300 ns EPROM Integrated Circuit | 136043-11159@ | Xe |
| 2¢ | 300 ns EPROM Integrated Circuit | 136043-112538 | 3 |
| aL | 300 ns EPROM Integrated Circuit | 136043-1117 CX | |
| 2p | 300 ns EPROM Integrated Circuit | 136043-1126 % X |
4R Type-82S129 PROM Integrated Circuit 136043-1103
| oP | 300 ns EPROM Integrated Circuit | 136043-1104 Ke |
| 10A | 200 ns EPROM Integrated Circuit | 136043-1105 XX |
| 108 | 200 ns EPROM Integrated Circuit | 136043-1106 * ® |
| loc | SLAPSTIC Custom Integrated Circuit. | _137412-106 |
| 16R | 300 ns EPROM Integrated Circuit | 136043-1120%% |
| 165 | 300 ns EPROM Integrated Circuit | 136043-111 9% |
ICs for U.S. Gauntlet It Game Only: Designator Description Part No.
| 6A | 200 ns EPROM Integrated Circuit | 136043-1121 Xe |
| 6B | 200 ns EPROM Integrated Circuit | 136043-1122 9¢ |
| 7A | 200 ns EPROM Integrated Circuit | 136043-1109 |
| 7B | 200 ns EPROM Integrated Circuit | 136043-1110 |
ICs for German Gauntlet II Game Only: Designator Description Part No.
| OA | 200 ns EPROM Integrated Circuit | 136043-1221 |
| 6B | 200 ns EPROM Integrated Circuit | 136043-1222 |
| 7A | 200 ns EPROM Integrated Circuit | 136043-1209 |
| 7B | 200 ns EPROM Integrated Circuit | 136043-1210 |
ICs for Japanese Gauntlet Il Game Only: Designator Description Part No.
| 6A | 200 ns EPROM Integrated Circuit | 136043-1421 |
| 6B | 200 ns EPROM Integrated Circuit | 136043-1422 |
| 7A | 200 ns EPROM Integrated Circuit | 136043-1409 |
| 7B | 200 ns EPROM Integrated Circuit | 136043-1410 |
Install the ICs Perform the following procedure to install the new integrated circuits (ICs).
& WARNING A To avoid electrical shock, unplug the game beyou have not already done so. fore performing the conversion procedures if 9 t=
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Conversion Instructions
- Remove the Gauntlet Game PCB from the cabinet. Refer to page 4-5 in the Gauntlet Operators Manual, Removing the Game PCB.
- Refer to the Gauntlet Game PCB Assembly, and determine the location of the ICs to be replaced and added, (See Figure 1.)
- Locate each IC to be replaced, and remove it with a chip extractor tool.
- For each installment IC, align all of the pins on one side of the chip, and bend that row inward so that it is parallel to the other row, Carefully insert the chip into the proper socket on the game PCB, making sure the orientation notch faces the correct direction.
- Then locate each new IC to be added, and insert it in its correct socket.
- Reinstall the Game PCB in the cabinet, connect all the harness connectors, and reinstall the control panel.
Install the Product
Identification Label
Perform the following procedure to install the Gauntlet II product identification label. 1, Remove the protective backing from the Gauntlet II
- Place the Gauntlet Il product identification label over the existing product identification label on the back of the cabinet.
Install the Display Sign Perform the following procedure to install the Gauntlet II display sign.
- Fold the bottom of the adhesive-backed cardboard display sign. Then fold the edge and bottom of the adhesive-backed display sign stand, Attach the stand to the center of the sign to become an easel.
- Place the sign on the top of your game. Be sure the adhesive-backed sign bottom adheres to the surface of the cabinet.
Install the Contest Promotion Items (U.S. and Canada Only) Perform the following procedure to install the Gauntlet II Player Quest Contest promotion items.
- Install the contest marquee according to the directions, then place the marquee behind and to the right of the display sign on top of your game.
- Place the contest poster in the front window of your location. Four-Player Gauntlet II
3, Place the contest entry forms in an accessible area in your location. (Players can also write to Atari Games Corporation for additional entry forms.)
Inspect the Game Before applying power, perform the following inspection procedure. 1, Carefully check that the Gauntlet II conversion kit parts have been properly installed. 2, Plug in the game power,
- Perform the self-test procedure as given in Chapter 3 of the Gauntlet Operators Manual. Be sure to reset the Restore Factory Default Settings option and to perform the Switch Test. Refer to the procedure in Reset the Game Options in this manual. 4, Be sure to reset the statistics and the histograms. Refer to the procedure in Reset the Statistics and Histograms in this manual.
- Securely fasten the spring draw latches under the control panel, Close and lock the front doors.
Reset the Game Options
After completing the Gauntlet II conversion, some game options should be reset. The game options are set in the Self-Test Mode. See Table 3 for the recommended settings. The recommended setting for the Health Per Coin option is 750 for Gauntlet II. Perform the following procedure for resetting the options.
- Press the Warrior Magic button until the Game Options screen is displayed. Note that the default (rec-
- Move the joystick up or down to select the Restore Factory Default Settings option. Move the joystick right or left to select the Yes setting. Press the Warrior Magic button. Refer to Chapter 3 in the Gauntlet Operators Manual for further information on setting the game options.
tad
=
Atari Games Corporation Customer Service
If reading through this manual does not lead to solving a maintenance or repair problem, call TELEHELP® at one of these Atari Games Customer Service offices:
United States Europe Parts and Service Parts and Service Atari Games Corporation Atari Games Corporation California Customer Service Office European Customer Service Office 737 Sycamore Drive Tipperary Town, Ireland P.O. Box 361110 Telex 28165 Milpitas, CA 95035 (Monday-Friday, 9:00-6:00 pm GMT) Telex 5101007850 = 0062-52155 (Monday-Friday, 7:30-4:00 pm Pacific Time) BS (408) 434-3950
© 1986 by Atari Games Corporation All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form ofa phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases, Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against any infringers, We will use all legal means to immediately halt any manufacture, distribution, or operation of acopy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari Games Corporation P.O, Box 361110 Milpitas, California 95035
Printed in the U.S.A. 7Q
Four-Player Gauntlet 11
Table 3 Game Option Settings Option Name Available Settings
Reset High Score Table No Yes <4 Sounds in Attract Mode No Yes <4 Restore Factory Default No Settings Yes Game Difficulty O—Easiest
2—Easy a 4—Moderate <4
6—Hard 7—Hardest Health Per Coin 100, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750 4, 800, 850, 900, 950, 1000 +, 1100, 1200, 1300, 1400, 1500, 1600, 1700, 1800, 1900, and 2000 Coins to Start 14, 2,3,4 Enable Secret Code Now # Yésial Disable Speech No <= ‘Yes Reduce Text No=# Yes
<4 Manufacturer's recommended settings Manufacturer's recommended settings for Japanese Gauntlet IT game only + Manufacturer's recommended settings for German Gauntlet II game only
Enable Secret Code Game Option A new game option called the Enable Secret Code is designed into the Gauntlet II game software. This option allows players to acquire a personalized secret code after finding their way to the secret maze and performing the required task. After successfully completing the task, players are asked to enter their full name (last name first) using up to 29 characters. The Enable Secret Code option is set by first displaying the Game Options screen in the Self-Test Mode. After selecting the Restore Factory Default Settings game option, then selecting the Yes setting and pressing the Warrior Magic button, the software automatically sets the Enable Secret Code option, If any U.S. or Canadian operator does mot want to participate in the Gauntlet II Player Quest Contest, the Enable Conversion Instructions
Secret Code option setting must be changed to mo. Perform the following procedure to change this setting.
- Enter the Self-Test Mode by turning on the self-test switch.
- Press the Warrior Magic button until the Game Options screen is displayed. Note that the default (recommended) settings are highlighted in green.
- Move the joystick up or down to select the Enable Secret Code option. Move the joystick right or left to select the No setting. Press the Warrior Magic button to save this setting and to obtain the next screen.
- Turn off the self-test switch.
Test/Repair the Joysticks and the Pushbuttons After installing the Gauntlet II conversion kit parts, the joystick and the pushbutton controls should be tested. Perform the following procedure to test the controls.
- Enter the Self-Test Mode by turning on the self-test switch.
- Display the Switch Test. Refer to page 3-3, Switch Test, in the Gauntlet IT Operators Manual for further information on both tests.
- Test the joysticks by moving each joystick into all eight positions. Moving the joystick up/down or left/right
should activate #vo switches. If two switches are not activated, then adjust or replace the switch. Also, once the joystick is moved into each position, wiggle the joystick. If the zero on the screen changes in any way, replace the switch. Refer to Removing the Joystick Leaf Switches in the Gauntlet Operators Manual.
- Testall the pushbuttons. Then wiggle the pushbutton. If the zero on the screen changes in any way, replace the switch. Refer to Removing the Pushbutton Leaf Switches in the Gauntlet Operators Manual.
The statistics and the histogram information should be reset after completing the conversion to ensure accurate
Conversion Instructions
game data. Perform the following procedure to reset this inf é 1, To reset the statistics information, display the Statistics screen in the Self-Test Mode, then press the Warrior Fire button. To reset the histograms, display the Histogram for Player 3 in the Self-Test Mode, then press the Warrior Fire button. Turn off the self-test switch, then close and lock the front doors. Refer to page 3-5, Statistics, and Histograms in the Gauntlet Operators Manual for further information. Four-Player Gauntlet I
Attract Mode The Attract Mode begins when the game is powered up or after exiting the Play or Self-Test Modes. The Attract Mode ends when coins or tokens are inserted. The Attract Mode continuously cycles through the following displays unless a player presses a button or moves a joystick: Gauntlet title screen *© Game play demonstration © Legend depicting all the objects the players can collect, such as treasure, food, and magic potions Monster screen: One screen displays all the monsters and how they differ Audiovisual credits High score table: One screen displays the high score per coin for each of the four characters Gata
a