CATHODE RAY TOMES

Super Puzzle Fighter 2 Turbo

Puzzle Fighter (Capcom, 1996) · Manual · 22 pages · 18 sections · original scan

Page 1

© CAPCOM CO., LTD. 1996 ALL RIGHTS RESERVED © CAPCOM U.S.A., INC. 1996 ALL RIGHTS RESERVED

OPERATORS MANUAL

/\\, WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

CAIRCOM¥ COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (847) 797-6100 Fax: (847) 797-6306 PM00164-KIT 022797

Page 2

CAPCOM” co-op, inc. PUZZLE FIGHTER™

THANK YOU FOR PURCHASING PUZZLE FIGHTER™ WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: FIELD SERVICE - VIDEO PRODUCTS 3311 N. KENNICOTT AVENUE ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE: (847) 797-6100 FAX: (847) 797-6306

THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

AAMA SERIAL NUMBER "B" CARTRIDGE SERIAL NUMBER

"A" CARTRIDGE SERIAL NUMBER (BOTTOM OF CASE) ‘300800

DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE:

“FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA SERIAL #

fidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC

Page 3

CAP@QON’ co-op, INC. PUZZLE FIGHTER™

TABLE OF CONTENTS

Warranty Information sanaeanennesteneenesseestsenseesnecesenesesseeseesecreesneeneeeeteneeeeeneeneess il

Kit Inspection a aaaeasseententesneceseceneceueenecnecenecsnsenessnseeuseensesecenetenessnneess 1

Caution i caeteeeteetetesesesesteestseseseseseseseseseseseseeneneneneseseseenenereees 2

“FULL” Kit ,“B” Kit Cabinet Preparation Kit Installation “ Control Panel Overlay Reassembly of Components Remote Volume/Test Switch Control Panel Wiring Cabinet Graphics Game Cartridges

Test Mode Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions ..-Configuration Menu System Configuration Game Configuration

Wiring References JAMMA Connections Auxiliary Cable Connections

Template : “Full-Kit"Control Panel Drill Hole(s) Template : “B-Kit” Control Panel Drill Hole(s)

Proprictary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP. INC]

Page 4

CAP@ON* coin-op, inc. PUZZLE FIGHTER™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products. that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. CPS II System Cartridges One (1) Year B. Electronic and Mechanical Components: (90) days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective:

B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED. INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER. IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, ING.

Page 5

CAPCOM’ coin-op, INC. PUZZLE FIGHTER™

KIT INSPECTION

There are two kits available for conversion to PUZZLE FIGHTER™ :

1)PF1000 (“FULL” kit) contains the2)PF1000B (“B™ kit)contains the game

complete game cartridges, all necessary graphics, software cartridge (B-cartri and must also be and replacement joysticks and button switches. The installed to a current CAPCOM® System II game. “FULL” kit is intended for conversion of most It includes all the necessary game graphics for a JAMMA-compatible, horizontal screen cabinets. cabinet conversion (marquee. control panel overlay, monitor card. etc.).

Check that all parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

KIT PARTS LIST

PF1000 PF1000B PART NO. DESCRIPTION

A-00717CPS II System Cartridges (A/B )1
vA-00718CPS Il System Cartridge ( B )1
|vvGE1200Monitor Card1
|vvAW00225Marquee1
vvAW00145-1Overlay, Control Panel1
VvVvAW00224Decal, Joystick & Button Switches1
VvVvAW00147Decal, Cabinet Side2
VvvAW00226-01 | Decal - Top. Instruction1
vVvAW00226-02Decal - Btm., Instruction1
vvPMO00164-KIT_|Manual, Operators1
vGE2010Joystick, 4-way2
v16-0130Switch, 1-Player Start Button (White)1
v16-0131Switch, 2-Player Start Button (White)1
vGE2520Switch, Button (Red/Blue)2
Vv03-0066Cable, Auxiliary Volume/Test1
|v03-0050Bracket. Volume/Test1

v 4 13-0066 Bracket. A-Cartridge Mounting $C00104-05 Screw, Wood 2]

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP. INC. 1

Page 6

CAPCOM coin-op, INC. PUZZLE FIGHTER™

[ CAUTION |

Please read the following instructions to keep the PC board in good condition:

#Do not block the ventilation slots.

#Do not drop or bump the board.

#Do not spill any liquids on the case.

Do not disassemble the case.

ATTENTION @>y The product that you have purchased contains a recyclable battery. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal

a? waste system. Check with your local solid waste official for

details in your area for recycling options or proper disposal.

DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY

OF YOUR REPAIR WARRANTY.

N Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 7

@APEOM coin-op, INC. PUZZLE FIGHTER™

KIT INSTALLATION

MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.

CABINET PREPARATION

“FULL” KIT

  • Disconnect and remove the old printed circuit board(s) from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the “Full-Kit” Drill Hole Template (included in this manual) over the control panel to determine proper hole locations. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional contro! panel cover (such as plastic or lexan) that will be utilized, cut any additional holes using the same template.
  • Plug-up unused holes with wood dowel (1-1/8" diameter), being careful to sand any rough edges. DO NOT use button plugs as they will cause an interference fit with the new dual-button switch included in this kit.
  • Remove the marquee covering, old marquee overlay, and the old cabinet graphics. Also, remove the monitor glass. “B” KIT
  • Remove or open the control panel. and disconnect and remove all buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the “B-Kit” Drill Hole Template (included in this manual) over the control panel to determine proper hole locations.
  • Plug-up unused holes with wood dowel (1-1/8" diameter), being careful to sand any rough edges, or use button plugs. if available.
  • Remove the marquee covering, old marquee overlay, and the old cabinet graphics. Also, remove the monitor glass.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® Ct wo

Page 8

CAPCOM coin-op, INC. PUZZLE FIGHTER™

INSTALLATION

CONTROL PANEL OVERLAY (SEE FIGURE 1, SEE FIGURE 2)

“FULL” KIT

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Again. place the “Full-Kit” Drill Hole Template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the joystick and button decals, align over the control panel holes, and press in place on the overlay. Using a knife, trim material from the center hole of the joystick decals.
  • Install the control panel cover (*if required).

Decals

2648 Overlay

TRIM TO SIZE

Control Panel viaoat

Figure 1: Overlay Installation (“FULL Kit”) “B” KIT

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel. leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Again, place the “B-Kit” Drill Hole Template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the joystick and button decals, align over the control panel holes, and press in place on the overlay. Using a knife, trim material from the center hole of the joystick decals.
  • Install the control panel cover (*if required).

Decals

Overlay

TRIM TO SIZE

vuaoa2 Control Panel

Figure 2: Overlay Installation (“B Kit”)

4 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-

Page 9

CAP@OM coin-op, INC. PUZZLE FIGHTER™ REASSEMBLY OF CONTROL PANEL COMPONENTS

“FULL” KIT “B” KIT

  • Install the dual-button switch and retaining ring to the 11. Re-install all-buttons and retaining ring to the control control panel. Make sure that the button colors are pane!. Make sure that the button colors are orientated as orientated as shown in Figure 3. shown in Figure 5.

Control Panel Control Panel

Red Blue Red Blue Red Blue Red Blue

Notch _47 g <—- "626 Retaining mi SZ Switch ‘ a ue Body LS?

viato-t 2 visio

FIGURE 3 : Dual-Button Switch Installation FIGURE 5 : Control Panel Buttons (“Full” Kit) (“B” Kit)

  • When locate the new dual-button switch. 12. Re-install all switches on the buttons as shown in Remove the switch body by twisting to the right and Figure 2. Orient the switches so that when a button is removing (see Figure 4). pressed, the red contact on the switch is depressed. Also, remove the retaining ring.

FIGURE 4 : Dual-Button Switch Removal

Proprietary and confider information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 5

Page 10

CAP@OM’ coin-op, INC. PUZZLE FIGHTER™

“FULL” KIT

  • There are two white buttons include in the kit (See Figure 6.). Install the | PLAYER button & retaining ring to the top left-hand side of the control panel and the 2 PLAYER button & retaining ring to the top right-side of the control panel. These buttons function as the game start buttons.

1 Player 2 Player

FIGURE 6: Start Buttons

  • Install all switches on the buttons as shown in Figure 3. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in Figure 7.

FIGURE 7: Joystick Installation

6 Proprietary and confidential infor “FULL” KIT CONTROL PANEL WIRING

NOTE: All switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch.
  • Reconnect the existing JAMMA connectors to the control panel according to the wiring connections shown in Table 1.

REMOTE VOLUMES TEST SWITCH

  • A remote Volume and Test switch bracket (see Figure 6) is included in this kit. Your cabinet may already contain this bracket. If you need to add the bracket to your cabinet, the bracket should be mounted inside the coin door and on top of the cash box for easy access.
NOTE: The A-cartridge also contains the same Volume and Test functions found on the remote switch bracket.

Figure 8: Switch Bracket

Wiring of the switch bracket (see Table 2) requires connections to both the main JAMMA harness as well as the auxiliary cable harness (refer to Figure 9).

To A-Cartidue

To Control Panel Button Switches (Not Used)

To Volume / Test ‘Switch Bracket vse Figure 9: Auxiliary Cable Harness

‘not to be disclosed or copied without the express pert

Page 11

CAPCOM” coin-op, INC. PUZZLE FIGHTER™

JAMMA CONNECTS

CONNECTOR REF. | *WIRE COLORTOCOMPONENTFUNCTION
WHITE.BLACKPLAYER |JOYSTICKuP
19WHITE/BROWNPLAYER |JOYSTICKDOWN
20WHITE/REDPLAYER |JOYSTICK.LEFT
21WHITE/ORANGEPLAYER |JOYSTICKRIGHT
22WHITE/YELLOWPLAYER 1BUTTON SWITCHROTATE LEFT
23WHITE/GREENPLAYER |BUTTON SWITCHROTATE RIGHT
vVIOLET/BLACKPLAYER 2JOYSTICKUP
WVIOLET/BROWNPLAYER 2JOYSTICKDOWN
xXVIOLET/REDPLAYER 2JOYSTICKLEFT
YVIOLET/ORANGEPLAYER 2JOYSTICKRIGHT
ZVIOLET/YELLOWPLAYER 2BUTTON SWITCHROTATE LEFT
aVIOLET/GREENPLAYER 2BUTTON SWITCHROTATE RIGHT.

Table 1: Control Panel Wiring Connections (JAMMA)

  • Wire Color Note:

SWITCH FUNCTION CONNECTS TO

YELLOW VOLUME-UP AUX. CABLE ‘29°(GRAY / YELLOW)

GREENCOMMONAUX. CABLE

‘31(BLACK / WHITE)

BLACKVOLUME-AUX. CABLE

DOWN ‘30’(PINK / YELLOW)

GREENCOMMONAUX. CABLE

‘31°(BLACK / WHITE) BROWN TEST JAMMA ‘15°

BLACKGROUNDJAMMA ‘A’ or ‘B’ or ‘e”

or “f or ‘1’ or ‘2’ or ‘27° or ‘28" Table 2: Switch Bracket Wiring

“FULL” KIT

  • Install the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 10.

~ SS

Figure 10: Mounting Bracket Installation

Proprietary and confident information, not to be disclosed or copied without the express permission of CAPCOM® Wire colors shown are according to the AAMA -AMOA Standard for wire color assignments; your harness may contain different col lors than shown above.

CABINET GRAPHICS INSTALLATION (Figure 13)

  • Install the new game marquee and re-install its” protective covering.
  • Peel-off the backing to the game instruction decals and place on both the top and the bottom sides of the monitor card. Also, apply the cabinet decals to both sides of the cabinet.

MARQUEE OVERLAY

MONITOR CARD CABINET

INSTRUCTION DECAL - BOTTOM

| INSTRUCTION | DECAL - TOP

vista Figure 13: Cabinet Graphics

Page 12

CAPCOM" coin-op, INC. PUZZLE FIGHTER™

/V\ CAUTION

IMPROPER INSTALLATION OF THE JAMMA HARNESS TO THE GAME CARTRIDGE WILL CAUSE DAMAGE TO THE ENCLOSED PCB.

GAME CARTRIDGE INSTALLATION

“FULL” KIT

  • Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 11.

Figure 11: Case Mounting

  • Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q-SOUND, also attach the audio cables.
  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

8 Proprietary and confi

WARNING

DISASSEMBLY OF EITHER GAME CARTRIDGE WILL VOID YOUR WARRANTY.

“B” KIT

  • To remove the existing “B” cartridge from the “A” cartridge, pull the old case clamps apart (see Figure 12). Carefully remove the old “B” cartridge and install the new “B’ cartridge. Re-install the case clamps.

\" Cartridge: Figure 12 : Case Clamp Installation

  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

ation, not to be disclosed or copied without the express permission of CAPCOM® COIN-«

Page 13

@ANP@OMI” coin-op, INc. PUZZLE FIGHTER™

TEST MENU

The test menu allows you to test the functions and configure the game. These items include input devices such as joys! Menu you can also access the Configuration Menu. where you can change the settings of the game

  • ACCESSING THE TEST MENU

TEST MENU . For a CAPCOM® cabinet, or a cabinet with INPUT a test switch:

OUTPUT Make sure the game is on and push the test switch. SOUND & VOICE The screen shown left will appear.

COLOR . For a cabinet without a test switch:

DOT CROSS. HATCH black plastic casing.

GAME DATA Refer to the inside back cover of the manual.

CONFIGURATION

MEMORY CHECK

EXIT 1.

2.

3.

4.

5.

6.

7.

8.

9.

SELECT = 1P UP or DOWN

START P SHOT1

  • HOW TO SELECT AN ITEM . Use the PLAYER I JOYSTICK to move the arrow in front of the desired item and press the PLAYER I SHOT | button, as shown below in various control panel configurations:

Player I Joystick Player 1 Start Player 2 Joystick Player I Joystick Player | Start Player 2 Joystick Sf . f- @ AR Sn ogo a@® oS |

Player 1 Shot 1 Player | Shot 2 vroo.s Player 1 Shot | Player 1 Shot 2 _

. To return to the test menu, push the PLAYER | START and PLAYER | SHOT / buttons simultaneously. . The test menu will always return to the screen:

  • After you exit the “7. CONFIGURATION MENU” and
  • After the memory is tested from the menu, “8. MEMORY CHECK”.

ad CLOSING THE TEST MENU To close the Test Menu, highlight “9, EXIT” and push the PLAYER J SHOT 1 button.

L Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, ING. cks, buttons and coin door or switches, output devices such as monitor, speakers and meters. Through the Test

Push the blue test switch on the outside of the

Page 14

CAPCOM” coin-op, INC. PUZZLE FIGHTER™

  • TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0 doesn’t change to a “1” when depressed or moved. OUTPUT Used to test the coin meter and the coin lock. SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER I JOYSTICK. Push the PLAYER | SHOT I button to hear the sound of the selected code. COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background. DOT CROSS Used to test the screen size, focus and distortion. HATCH GAME DATA Coin meter and playtime information will be displayed. CONFIGURATION _| Used to change the game play settings. Refer to tle CONFIGURATION MENU section. MEMORY CHECK _ | Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if *NG” still appears. EXIT Select this item and push the PLAYER I SHOT J button to return to game play mode.

10 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, ING.

Page 15

CAP@ONI” coin-op, INC. PUZZLE FIGHTER™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty. credits, sound configuration, etc. These settings are stored in memory on the PCB.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

  • ACCESSING THE CONFIGURATION MENU
  • CONFIGURATION MENU * From the TEST MENU, move the arrow to “7, CONFIGURATION” and push the > 1. SYSTEM PLAYER I SHOT 1 button. The screen left will be displayed. A description of each option is explained in the table below.
  • GAME
  • DEFAULT
  • SAVE & EXIT

SELECT 1P UP OR DOWN START 1P SHOT1

SYSTEM _| Select this item to change settings for credits, monitor flip, sound and coin door configurations. | GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds | and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER | SHOT / and PLAYER 1 SHOT 2 buttons at the same time to restore default values. SAVE & Use this to save new configuration settings and exit to the Test Menu. The message “SAVING NEW | EXIT CONFIGURATION IN EEPROM?” will appear while the new settings are being saved. DO NOT turn | power off to the game until “SAVING” is complete and the Test Menu reappears. |

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 1

Page 16

CAPCOM” con-op, INC. PUZZLE FIGHTER™

7-1. SYSTEM CONFIGURATION

  • COIN MODE1 COIN 1 CREDIT

. CONTINUE

. MONITOR

. DEMO SOUND

. SOUND MODE

|. CHUTE TYPE

  • EXIT

SYSTEM CONFIGURATION

CHANGING THE SYSTEM CONFIGURATION SETTINGS

Move the PLAYER I JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER I JOYSTICK left or right or press the PLAYER I SHOT | button to select. ON

NORMAL

ON

STEREO (QSOUND)

2 CHUTES SINGLE

SELECT OPTION = 1P UP OR DOWN MODIFY SETTING= 1P LEFT OR RIGHT =1P SHOT1 OR SHOT2

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

  • COIN MODE SELECT THE CHARGE PER PLAY.
  • CONTINUE SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY,
  • MONITOR FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL.
  • DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF.
  • SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET.
NOTE: STEREO SHOULD ONLY BE SELECTED FOR USE WITH CAPCOM® QSOUND CABINETS.
  • CHUTE TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTE TYPE.
  • EXIT TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH EITHER THE PLAYER | SHOT 1 BUTTON OR THE PLAYER 1 SHOT 2 BUTTON

SYSTEM CONFIGURATION OPTION SETTINGS

  • COIN MODE
  • CONTINUE |3. MONITOR |
NOTE:
1 COIN1 COIN1 COIN1 COIN1 COIN
1 CREDIT2 CREDITS3 CREDITS4 CREDITS5 CREDITS
1 COIN1 COIN1 COIN1 COIN2 COINS
6 CREDITS7 CREDITS8 CREDITS9 CREDITS1 CREDIT
3 COINS4 COINS5 COINS6 COINS7 COINS
1 CREDIT.CREDIT1 CREDIT1 CREDIT1 CREDIT

8 COINS 9 COINS 2 COINS START FREE PLAY 1 CREDIT 1 CREDIT | COIN CONTINUE ON OFF NORMAL FLIP ON OFF STEREO (Q SOUND) MONAURAL 2 CHUTES SINGLE 2 CHUTES MULTI 1 CHUTE SINGLE

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM COIN-OP, ING.

Page 17

@APEOM” coin-op, INc. PUZZLE FIGHTER™

GAME CONFIGURATION

7-2. GAME CONFIGURATION CHANGING THE GAME CONFIGURATION ; SETTINGS =

DIFFICULTY MEDIUM HARD

DAMAGE LEVELNORMALMove the PLAYER | JOYSTICKup or down to highlight
GAME SPEEDFASTESTthe desired option. Once the option is highlighted. move

the PLAYER | JOYSTICK left or right or press the

Ne hadTHEESPLAYER I SHOT J button to select

4PMAXROUND 1

2PMAXROUND 1

. JOIN-IN ON

. HANDICAP OFF

  • EXIT

SELECT OPTION =1PUPORDOWN MODIFY SETTINGS =1P LEFT OR RIGHT 1P SHOT1 OR SHO’ N

3.

4,

5.

7.

DESCRIPTIO!

1.SETS THE GAME DIFFICULTY LEVELSIESEASYMEDIUM

DIFFICULTY

EDHARDVERYHARDEST

RD HARD

2, DAMAGE __| SETS THE NUMBER OF COUNTER GEMS. THE HIGHERLOWORHIGHMAXIMUM

LEVEL THE LEVEL. THE MORE COUNTER GEMS APPEAR ON THE OPPONENT'S FIELD.

3. GAMESETS THE SPEED AT WHICH THE COUNTER GEMS DROP.SLOWNORMALFAST

SPEED

4. GAMESET GAME PLAY OPTIONS:PTYPE BTYPECTYPE D

DARD (MATCH

MODE MODE)

TYPE A: *DURING | CREDIT GAME: PLAYER'S OPPONENT IS “VS CPU”. JOIN-IN ROUND IS PLAYED “VS CPU". CONTINUE IS ENABLED. *DURING 2+ CREDIT GAMES: JOIN-IN ROUND IS PLAYED “VS HUMAN™ TYPE B: *DURING | OR MORE CREDIT GAME(S): PLAYER CAN CHOOSE BETWEEN “VS HUMAN” OR “VS CPU” OPPONENTS. JOIN-IN ROUND IS PLAYED “VS CPU. CONTINUE IS ENABLED. TYPE C: *DURING 1 OR MORE CREDIT GAME(S): PLAYER CAN CHOOSE BETWEEN “VS HUMAN™ OR “VS CPU” OPPONENTS. JOIN-IN ROUND IS PLAYED “VS CPU”. CONTINUE IS DISABLED. TYPE D: OR MORE CREDIT GAME(S): - PLAYER'S OPPONENT. 'S HUMAN™. JOIN-IN AND CONTINUE ARE NOT AVAILABLE: THE GAME ENDS AFTER ONE MATCH IRREGARDLESS OF THE RESULT.

5. 1P MAXHE NUMBER OF ROUNDS PER MATCH WHEN1 ROUND3 ROUNDS3 ROUNDS

ROUND PLAYING “VS CPU 1 ROUND: WINNER OF THE SINGLE ROUND WINS. 3 ROUNDS: WINNER OF 2 OUT OF 3 ROUNDS WINS

  • ROUNDS: WINNER OF 3 OUT OF 5 ROUNDS WINS.
6. 2P MAXSETS THE NUMBER OF ROUNDS PER MATCH WHEN1 ROUND3 ROUNDS3 ROUNDS

YING “VS PLAYER” (WINNER IS DETERMINED AS IN ABOVE) ROUND

  • JOIN-IN LOWS A SECOND PLAYER TO PARTICIPATE

ALLOWS EACH PLAYER TO SELECT BETWEEN EASY (1) TO HARD (3) GAME PLAY

  • EXIT RETURN TO THE CONFIGURATION MENU
  • HANDICAP

NOTE: RY SETTING

Proprietary and (0 be disclosed or copied without the express permission of CAPCOM® COIN-OP,

Page 18

CAPCOM coin-op, INC. PUZZLE FIGHTER™

JAMMA CONNECTIONS

GND GND +5 VDC +5 VDC N.C. +12 VDC KEY NIC COIN LOCK 2 *SPEAKER (-) Nc. VIDEO GREEN VIDEO SYNC SERVICE (FREE CREDIT) NIC 2 PLAYER - COIN 2 PLAYER - START 2 PLAYER - JOYSTICK (UP) 2 PLAYER - JOYSTICK (DOWN) SCKCHODvsZzSZrAaoDamonee 2 PLAYER

  • JOYSTICK (LEFT) cal 2 PLAYER
  • JOYSTICK (RIGHT) 2 PLAYER
  • BUTTON (ROTATE LEFT) 2 PLAYER
  • BUTTON (ROTATE RIGHT) NIC NIC NIC GND GND veN<

mom COYNE WH GND GND +5 VDC +5 VDC NC. +12 VDC KEY COIN COUNTER 1 COIN LOCK 1 *SPEAKER (+) N.C. VIDEO RED VIDEO BLUE VIDEO GND. TEST MODE (DIAGNOSTICS) 1 PLAYER - COIN 1 PLAYER - START 1 PLAYER - JOYSTICK (UP) 1 PLAYER - JOYSTICK (DOWN) 1 PLAYER - JOYSTICK (LEFT) 1 PLAYER - JOYSTICK (RIGHT) 1 PLAYER - BUTTON (ROTATE LEFT) 1 PLAYER - BUTTON (ROTATE RIGHT) NIC NIC IC GND GND.

*NOTE: FOR CABINETS EQUIPPED WITH CAPCOM® “Q” SOUND, AUDIO CONNECTIONS ARE MADE THROUGH THE A-CARTRIDGE WITH RCA-TYPE CONNECTORS.

AUXILIARY CABLE CONNECTIONS

NIC NIC NIC

NIC

iC CONNECTOR EVEN ROW | WIRE COLOR

NIC NIC NIC NIC NIC GRAY/YELLOW TEST BRKT-VOLUME UP. TEST BRKT-VOLUME DOWN BLACK/WHITE TEST BRKT-VOLUME COMMON PINK/YELLOW NIC BLACK NIC NIC

10 be disclosed or copied without the express per BLACK

Page 19

1-3/16" DRILL FOR 1P OR 2P START BUTTON SWITCH

1-3/4" DRILL FOR JOYSTICK HOLE

1-3/16" DRILL FOR

a BUTTON SWITCH HOLE

\ ’ \

CAPCOM COIN-OP, INC. 2311 NORTH KENNICOTT AVENUE PHONE 708) 797-6100 | COIN-OP, INC. FAX (108) 797-6119 i ME "FULL-KIT" DRILL HOLE TEMPLATE: SUPER PUZZLE FIGHTER Il TURBO

DRAWN BY: 6-25-96 JA

1406-1 i |*

Page 20

1-3/16" DRILL FOR 1P OR 2P START BUTTON SWITCH

1-3/4" DRILL FOR JOYSTICK HOLE

1 \ 1-3/16" DRILL FOR ' , BUTTON SWITCH HOLES

1+1ier opecocfta
\!7~,,~y
\/’<’\

\ /

CAPCOM CONOP, INC 3311 NORTH KENNICOTT AVENUE ARLI IN HEIGHTS, ILLINOIS 60004 PHONE (706) 797-6106 COIN-OP, INC. FAX (708) 797-61:9 TE "B-KIT" DRILL HOLE TEMPLATE: SUPER PUZZLE FIGHTER II TURBO

DRAWN EY: 6-25-96 JA DATE

1406-2 | bea

Page 21

@AP@ON "coin-op, Inc. PUZZLE FIGHTER™

REFERENCE INFORMATION

GAME CASE CONTROLS

COIN REGISTER COMMUNICATION

(wor useD) (NOT USED) PORTS (NOT USED)

OUT IN

TEST

*VOLUME UP

*VOLUME DOWN

JAMMA AUXILIARY CABLE AUDIO OUT (FOR Q SOUND) CONNECTOR CONNECTOR RIGHT: RED, LEFT: WHITE vva00800

TYPICAL CONTROL PANEL LAYOUTS FOR PUZZLE FIGHTER™

“FULL-KIT”

“B-KIT”

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 22

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

CAIRCOMY COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (847) 797-6100 Fax: (847) 797-6306

Copyright © 1996 CAPCOM ® coin-op, INC., All Rights Reserved