CATHODE RAY TOMES

Anti Aircraft TM-025

Anti-Aircraft (Atari, 1975) · Technical Manual · 45 pages · 8 sections · original scan

Page 1

TM-025

Operation, Maintenance and

Service Information

ATARI Innovative leisure

ATARUING 14600 WINCHESTER BOULEVARD, LOS-GATOS, CALIFORNIA 95030 = TELEPHONE (408) 374-2440 + TELEX 357-488

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

TABLE OF CONTENTS

Sec. Title

Section 1. General Maintenance Information

1-1. Introduction

1-2. Warranty 1-3. New Machine Setup Procedure

1-4. Service Access

1-5. New Machine Checkout

1-6. TV Adjustment 1-7. Coin Acceptor: Operation, Adjustment and Maintenance

1-8. General Machine Maintenance

Section 2. Circuit Description

2-1. Play 2-2. Circuits

  • Syne
  • Coin/start
  • Planes 4, Missiles
  • Hit detection/score
  • Launchers
  • Angle/firing controls
  • Sound
  • Power supply
  • Video mixing 2-3. Setup Procedure
  • Game time
  • Volume control

Section 3. Customer Service Information

3-1. Test Equipment 3-2. Required Equipment 3-3. Optional Equipment 3-4. Troubleshooting 3-5. PCB Shipping 3-6. Logic Type and Function List 1-1

1-1

1-2

1-2

1-3

1-3

1-5

PP Pp PPMP MO pm y my NIN WV INMAGMEEWNN ND

3-1

3-1

3-1

3-2

3-4

Page 4

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 5
  • GENERAL MAINTENANCE INFORMATION

1-1. INTRODUCTION

The Atari Anti-Aircraft II game consists of a cabinet, TV monitor, a printed circuit board (PCB) computer, interconnecting wiring, and various cabinet-mounted circuit components. Except for a schematic, no information about the TV monitor is presented in this manual. The TV monitor is a Motorola XM501 unit. TV circuit malfunctions can be solved using standard TV troubleshooting techniques. However, the PCB computer requires troubleshooting techniques that may be unfamiliar to the average technician. Therefore, the troubleshooting information in the manual is mainly devoted to the PCB computer and its associated cabinet circuitry.

1-2. WARRANTY

Be sure to return the enclosed warranty card immediately upon unpacking your Atari game, to ensure continued protection under the terms of the warranty.

This game has been designed with solid-state circuitry to be as maintenance-free as possible. However, as with all mechanical or electrical devices, there may be minor problems. If the PCB fails within the 90-day* warranty period, contact the distributor from whom the game was originally purchased for replacement or repair instructions. Any PCB repairs attempted by anyone other than authorized Atari Service Center personnel will void the warranty. If the PCB fails after the warranty period has expired, it will be repaired for a nominal parts and labor charge.

Atari, Inc. warrants the TV monitor for a period of 30 days commencing the day of shipment from the Atari factory. If the monitor fails within that period, immediately contact the distributor from whon the game was originally purchased for repair or replacement instructions. Any TV repairs (other than replacement of fuses or adjustments) attempted during the warranty period by anyone other than authorized Atari Service Center personnel will void the warranty.

*from date of shipment from the factory

1-1

Page 6

If the TV monitor fails after the warranty period has expired, it may be returned to the distributor where it will be repaired for a nominal parts and labor charge, or it may be taken to any competent TV repair shop.

1-3. NEW MACHINE SETUP PROCEDURE

Before turning this machine on, inspect it carefully for any damage that may have occurred during shipment. Inspect both interior and exterior of the machine for any obvious damage to the cabinet or internal components. Check for cracked or broken cabinet parts, assemblies pulling loose, broken or disconnected wires, or foreign objects shorting electrical connections. After the machine has been plugged in and turned on, perform the checkout procedure.

1-4. SERVICE ACCESS

All servicing is performed at the rear of the machine through the rear door that provides access to all components, sub-assemblies, and adjustments except for the coin box. The coin door is located on the front of the machine underneath the control panel. To remove the coins, unlock the metal coin door with one of the two keys provided and open. This exposes the coin box.

To reach the interior of the machine, unlock and remove the rear door. Please note than an interlock switch is provided for this door so that the machine is completely turned off whenever this door is opened. These switches protect the operator from accidental shock and thus must ALWAYS be kept in perfect working order. If the machine is adjusted or tested with the rear door open, the interlock switch must be placed in the closed (or "on" position) by pulling out the white actuator shafts.

WARNING: The covered black terminal block carries full line volt-+ age whenever the line plug is connected to a power outlet. This cover should be removed only with the line plug disconnected. Do not leave off the cover once it has been removed.

1-2

Page 7

1-5. NEW MACHINE CHECKOUT

As each new machine leaves the factory, every component and subassembly is carefully checked for proper operation. However, since parts may have been damaged or adjustments changed during shipping, the following checkout procedure must be repeated prior to placing the machine on location:

  • Carefully inspect the interior of the machine to see that all solder joints, slip-on connectors and plug-in type connectors are firmly seated. Pay particular attention to the PCB edge connector, the fuses and any connectors to the potentiometers. Also check the connections to the coin switch, the TV monitor, the interlock switches and all the other Molex-type connectors.
  • Plug the machine in, and pull out the white actuator shafts of the interlock switches if the rear door is open. Inspect the cathode ray tube (CRT) image for a steady and sharp picture that exhibits the proper levels of brightness and contrast.
  • Insert several old and new coins into the coin acceptor. No genuine coin should be rejected and each coin insertion should advance the coin counter one digit. Depress the coin rejector button to make sure the linkage is operating smoothly.
  • Coin insertion should start the game. Check for proper game sequence, making sure that all aspects of the game are functioning correctly.
  • The door locks should turn to the locked and unlocked positions smoothly and the doors should open and close without binding.
  • The interlock switches must turn off the entire machine when the rear door is opened.

1-6. TV_ADJUSTMENT

Monitor circuitry includes four stages of video amplification -- a twostage audio amplifier, sync and deflection circuits, and a regulated power supply. An additional 5-volt supply is included to power the external logic system. The adjustment of the TV monitor functions like that of a normal TV set. The only exception is that the TV's audio portion is not used. The volume control is located on the PCB. The CRI image is adjusted through the rear door,

Page 8

Brightness: Adjust the brightness, then the contrast. Adjust so that the CRT background is as dark as possible. Contrast: Adjust so that images displayed on the CRT are as bright and clear as possible without being blurred or smeared. Vertical hold: Adjust the vertical hold only if the picture is rolling up or down the screen. Adjust for a centered picture by turning the control to the middle of the stable range. Horizontal hold: If the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken into a series of diagonal lines, adjust the horizontal hold same as vertical hold. Yoke: The yoke should never need adjustment unless the controls have been tampered with or the machine damaged. If yoke adjustment is necessary, adjust both yoke rings simultaneously for optimum centering of the image on the CRT. This adjustment is best handled by a qualified service person. Five-volt supply: This is located on the power/audio PCB which is on the left side of the monitor behind the power transformer. There is a 1000-ohm trimpot to adjust the supply voltage. This measurement should be made on the logic PCB to allow for a voltage drop between monitor and PCB. Regulator adjustment: Connect monitor to AC line supply. Adjust horizontal and vertical controls until display is synced. Connect a precision voltmeter to any of the 73-volt test points and adjust regulator control R74 on PCB for an output of 73 volts. CAUTION: Do not run the regulator control through its range or you may damage the monitor. Only a slight turn is necessary for proper adjustment. Both the 5-volt and 72-volt adjustments have been made at the factory and under normal conditions should not need readjustment. AC voltage switch: Set this switch to the 115V position ("115" visible on the switch) if the machine is connected to a 115-volt source. Set it to the 230V position ("230" visible on the switch) if the machine is connected to a 230-volt source. The TV monitor will not function

if this switch is misadjusted. NOTE: If the monitor of a 230-volt machine is set to 115 volts, it will blow the machine line-fuse repeatedily.

Page 9
  • TV monitor fuse: One 6/10-amp, 250-volt fast-blow fuse protects the TV from electrical overload (for 155-volt operation, the TV fuse must be l-amp fast-blow). Replace blown fuses ONLY with those which have the above rating. This fuse is located on the electronics mounting board inside the rear door. The fuse farthest from the door is the

TV fuse, and the fuse nearest the door is the PCB fuse. The PCB fuse should be replace ONLY with a one-amp, slow-blow, 250-volt fuse.

  • Monitor PCB removal:
  • Power/audio PCB: Locate board on the left side of the monitor

behind the power transformer. To remove, pull board up. To replace board, locate the slot between pins 3 and 4, and hold this side on your left; then insert board into the connector.

  • Monitor PCB: To remove, use a screwdriver or similar object and slowly pry up off of the chassis until it clears the pins. Next, unplug the socket from the yoke and slide board out. To replace this board, follow the above steps in reverse order. The monitor can be removed through the cabinet's rear access door. This door also provides access to the logic PCB, transformer assembly, and main harness connectors.
CAUTION: Any work performed on monitor chassis should be done only by qualified service personnel who are familiar with servicing procedures and precautions.

1-7. Q-530 COIN ACCEPTOR: OPERATION, ADJUSTMENT AND MAINTENANCE

All coin acceptors leave the factory adjusted for maximum performance. If, however, more critical adjustments are desired, or if the unit has been completely disassembled for service, the following adjustment procedure is suggested. If the coin acceptor has been removed from the machine, place it is a vertical position on a level surface. If the acceptor is still mounted on the coin door, place the coin door in a vertical posi-~ tion on a level surface. See exploded coin acceptor and mechanism drawings on page 1-8.

  • Kicker and separator
  • Set the acceptor with the back of the unit facing you in the test position.
  • Loosen the screws holding the kicker (1) and the separator (3) and move both the kicker (2) and the separator (4) as far to the right as they will go. Tighten the screws.

1-5

Page 10
  • Insert several test coins (both old and new) and note that some

are returned by striking the separator.

  • Loosen the separator screw and move the separator a slight amount to the left. Tighten the screw.
  • Insert the test coins again and, if some of them are still returned, repeat step (d) until all the coins are accepted. (£) Loosen the kicker screw and move the locker as far to the left as it will go. Tighten the screw.
  • Insert the test coins and note that some are returned.
  • Loosen the kicker screw and move the kicker a slight amount to the right. Tighten the screw.
  • Insert the coins again and, if some are still returned, repeat step (h) until all the coins are accepted.
  • Be sure that both screws are tight after the adjustments have been made.

Magnet gate

  • Set the acceptor with the front of the unit facing you in the test position.
  • Turn the magnet gate adjusting screw (2) out or counterclockwise until none of the coins will fit through.
  • With a coin resting in the acceptor, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
  • Test this adjustment using several other coins, both old and new, and if any of them fail to pass the magnet gate, repeat step (c) until all the coins are accepted.
  • Fix the magnet gate in this position with a drop of glue or Loctite", if necessary. Acceptor maintenance Depending on the environment in which the acceptor is used, periodic preventive maintenance should be performed. The mainplate (5) may be cleaned with any household cleaner. Thorough rinsing and drying are necessary to remove deposits and/or film. Remove all metal particles from the magnet by guiding the point of a screwdriver or similar tool along the edges of the magnet. You will notice that the particles will cling to the point of the tool. Remove the transfer cradle (9)

1-6 5

Page 11

and the undersize lever (10) and clean the bushings and the pivot pins. A pipe cleaner is an effective cleaning tool. Apply powdered graphite or pencil lead to the pivot pins and bushings and reassemble. Spray the entire unit lightly with wo-u0®, a silicone lubricant.

1-8. GENERAL MACHINE MAINTENANCE

Due to its solid-state circuitry, your machine will require very little maintenance other than periodic cleaning, lubrication and TV monitor adjustment. The cabinet and plexiglass screen may be cleaned with any nonabrasive household cleaner. The coin acceptor and the rejector linkage should be sprayed lightly once every three months with wD-40® or similar

silicone lubricant. The potentiometer shafts must never be lubricated in any way. The TV monitor is adjusted only when the CRT picture is distorted, or if the contrast or brightness appear to be out of adjustment.

Page 12

KICKER SCREW KICKER SEPARATOR SCREW SEPARATOR MAINPLATE ASSEMBLY. GATE ASSEMBLY COVERPLATE ASSEMBLY RAIL CRADLE ASSEMBLY UNDERSIZE LEVER MAGNET GATE ASSEMBLY MAGNET GATE ADJUSTER SCREW LOWER GATE PIVOT SPRING UPPER GATE PIVOT SPRING GATE PIVOT PIN WIPER LEVER SPRING WIPER LEVER WIPER COIN ACCEPTOR - EXPLODED

COIN MECHANISM — EXPLODED

1-8

Page 13
  • CIRCUIT DESCRIPTION

2-1. PLAY

The picture below shows the normal game:

Perera Sake ee} LIGHT AREA —>+

AIRCRAFT

Attract: In the attract mode, the guns are locked in the center-aimed position, and are continuously firing. The aircraft fly over the guns either singly or in pairs, from the right or the left within the aireraft flight area. If an aircraft should be hit by a shell directly or by an exploding shell, it will disappear. During the attract mode, the score is disabled, as are the sound and player controls.

Play mode: Anti-Aircraft II is a two-player game that has an operatorselected option of one or two games for a quarter. The game incorporates a coin mechanism and a start button. Each player (#1 on the left and #2 on the right) has an antiaircraft gun that positions itself in any of three positions and then fires when the proper control button is pushed. The object of the game is to shoot down more aircraft than your opponent does in the time allotted.

Page 14

2-2. CIRCUITS

  • Syne The sync circuit located at C- and D-8,7,6,5 on page 1 of the schematic is a semi~synchronous syne circuit. Its standard crystal is 14.318 MHz. The bits clock through 128H are fully synchronous; the rest of the bits are asynchronous. H syne is set by HRESET after 457H counts is 32H long. The vertical sync divide~by-260 section clocked by HRESET has a VSYNC of 8V.
  • Coin/start

The coin/start circuitry is located at C- and D-1,2,3,4 of schematic page 1 and includes devices F9, F8, E9, the electronic latch located at D-2, page 1, E8, D8, and D9. When the coin switch or coin mechanism external to the PCB is activated, a square wave pulse is proportional in length to the amount of time the coin used to activate the mechanism. The square wave pulse is present at the R-S flip flop, the latter being comprised of two inverters, F9 pin 4. This pulse is fed into the discriminator made up of two D-type flip flops (F8). This circuit determines whether or not the pulse was long enough to be a genuine coin pulse or just a switch bounce that can be induced by pounding on or near the coin mechanism. If the pulse is long enough, it is passed along and sets the electronic latch. At this point, F9-8 goes low enabling the credit light and FS-10 goes high (Q goes high) which releases the D-type flip flop D8-1, the timer DS, and the attract flip flop D8-10. Now when the start switch is depressed by a player, START (D8-5) goes high, ATTRACT (D8-3) goes low, and the timer is set. Depending on the PLAY TIME pot (1 meg, R36), the game will last between 30 seconds and three minutes, and at the control's center position will last approximately 90 seconds. At the end of the timing sequence, D9-5 will go low, transmitting a rising edge to D8-11, which clocks ATTRACT high. If the one-play/two-play switch (located D13, page 1) is in the one-play position when ATTRACT goes high, E9-8 will go low, dropping the electronic latch out and inhibiting the start circuitry. If, however, the switch is in the two-play position, ATTRACT will have to go high once more (at the end of the next game) in order to drop out the latch. Thus the start circuitry will not be inhibited and a push on the start switch will start game #2.

2~2

Page 15
  • Planes

The plane motion circuitry and exact shape-generating systems are located near A~ and B-3,4,5,6,7,8 of schematic page two. The normal horizontal-motion circuit is comprised of counters Hl and Fl and flip flop F2 at the end of the counters. The horizontal speed and direction are determined by the speed code presented at pins 4,5, and 6 of counter Hl. The code presented at these pins will make the count chain either two counts longer or shorter than the horizontal syne chain, meaning the horizontal window will move either two counts per frame to the vight or to the left respectively. The direction then is determined by DIR. SEL (F2) being clocked by a random clock during plane reset, and the speed is fixed at two counts per frame. The horizontal window is 16 counts wide and is determined by AND gate H2-1 and -2; the horizontal window is

present at H2-3. The vertical motion circuit is unusual because it does not produce actual movement, but rather windows 8V wide. It produces two windows 8V wide at D3-6 displaced by 8V. These windows can be anywhere between 64V and 64 + 128 = 192V, dictated by J2, an exclusive OR. These two windows are impressed upon D2-3 and D2~1i and if the other inputs to the respective gates are satisfied, a vertical window will be at D2-6 and another window displaced by 8V will be at D2-8. Each window will be 8V wide. The reasons for the other inputs not being satisfied would be if flip flop D1l-6 came up high due to random clocking during plane reset, or if either plane were hit. Such a hit would cause a HIT DETECT pulse at C2-9 and C2-12 at the sane time there is a high at C2-10 or C2-13 (depending on which window area the plane was hit in). In addition, this hit would cause a reset of the flip flop that controls that plane window. The vertical and horizontal motion circuits are summed at H2-10 and -9 to produce one or two windows 8V high and 16H long at H2-8, called PLANE EN. The actual shape of the plane is contained in ROM Kl which is a programmed 82S23 PROM. The picture is brought out of the ROM one H line at a time (seen as a vertical line 1H wide and 8V tall on the screen), from either the left or right, depending on direction of plane, and therefore level with DIR. SELECT. This one line brought to the outputs of the ROM is strobed from top to bottom by the 9312 (L1). The PLANE is thus brought

2-3

Page 16

out one H line at a time serially at L1-15 in correspondence with the PLANE EN window(s).

4, Missiles

The right and left missile circuits are exactly the same in construction; for the sake of simplicity we examine the right missile circuit located around B-1,2,3,4 of schematic page 1. These two missile circuits are standard motion circuits. The horizontal

motion count chain is made up of counters M8, M7, and F7 with some external gating. The NAND gate N8-3 keeps the circuit at reset until the right gon is fired or until N@-1 goes low while N8-2 is low (when the CRT is

scanning the missile base). The speed of the missile is determined by the speed code present at counter M8, pins 4, 5, and 6. This speed code is in turn determined by RA and RB as shown by the external gating. The level of RA and RB is determined by the laucher's position at firing time as shown by the table at A-7 and -8 on schematic page 2. In a similar fashion, the vertical-motion counting chain is made up of L7, L8 and external gating. The vertical speed code presented at L7-3, -4, and -5 is also dependent upon the position of the launcher at firing time and thus RA and RB. The circuit comprised of K7, H7, J2, L6, and H6 is used to display an exploding shell at the proper time.

  • Hit detection/score

This circuit is located on schematic page 2 and covers most of the page's upper half; the circuit starts in the C-7 and C-6 area and proceeds to the right and up. The two 9602s Bl control the explosion sequence. As shown by the gating directly before them, the right missile window comes in contact with the V plane window, A2-1 and -2 go high and thus H2-3 goes high, triggering 9602 Bl-4 which initiates the explosion sequence. Ina like manner, if the left missile window comes in contact with V plane window, the explosion sequence will be initiated. These are not necessarily aircraft hits but rather hits on the lowest plane window or closest to the guns. Such a hit will cause the shell to explode in the path of the lower aircraft.

If the aircraft is hit directly by a shell or flies into an exploding shell, it will be counted as a hit for the player who fired the shell. The hits are produced by the outputs of B2-8 and B2-11; the latter will go low if

Page 17

the respective missile comes in contact with the plane window. This low produces a clock pulse at the appropriate score-counting chain, C4-14 or B4-14 (left score or right score respectively). These scores are multiplexed by the two 74153s, A¥ and A5, and are brought into the 7448 BCD-toseven-segment decoder A6 at the proper times for display on the screen. The outputs of the 7448 (A6) are fed into B6 and A7 that provide the actual shape of the individual seven-segment display. Part of the gating below the two 74153s, A4¥ and A5, is used to make the missile bases as shown by the composite output of B3-5 (score and missile bases).

  • Launchers

The launcher circuitry is located around A- and B-9,7,6,5 on page one of the schematic. The circuitry for the left and right launchers is essentially the same, so we will examine only the right launcher located near B7 and A7, including devices M5, L4, M4, and N5, and surrounding gating. Simply speaking, RA and RB were previously found to be related to the horizontal and vertical speeds of the missile and hence the angle of the missile. RA and RB are fed into the select lines of the two multiplexers M5 and L4. The inputs of the multiplexers are various H counts. When properly selected by RA and RB (depending on which control button is pushed), these H counts are transmitted via the outputs of the multiplexers and the comparator M4 (the 4-bit digital comparator 7485). At M4, these H counts are compared with V counts to produce a launcher barrel line of the appropriate angle for the motion of the missile. Note that V counts are inverted and thus reversed for the left launcher to

Frovide an opposite angle or mirror image of the right one. These signals are then brought into a one-shot (9602) El for both launchers; the width of these lines is determined by the RC time constant of C25 and R39. Thus we have a thin line made into a barrel by El.

  • Angle/firing controls This circuit is located at B~ and C-8,7,6,5 of the schematic's page one. SW1 through SW6 are the external controls used by the players to control the angle of the launchers and the firing of the missiles. The actual angle of the launcher and which launcher is being controlled are shown by the chart at C8, just above the switches. The multiplexer J9 is con-

2-5

Page 18

tinuously being selected by 1H and 2H. The timing between these H counts and the outputs of J9 determines the levels of RA, Rb for the right player and LA and LB for the left player, as produced by the interconnecting flip flops K8 and K9. In turn, the outputs of J9 depend on the button pushed. If a button is not pushed, the angle of the launcher will remain the same; when a button is pushed, the angle will change, the missile will fire, and it remains at this new angle until a different button is pushed. Farther to the right on the schematic are the FIRE RIGHT and FIRE LEFT control flip flops. These flip flops are cleared when a fire button on the proper side is pushed. The complement output Q of these flip flops disables the multiplexer J9 during the firing sequence to prevent changing the launcher angle during launch. The fire signal is clocked away; thus the multiplexer is released when the missile hits something (plane or V plane window) or when the missile goes off into blanking.

  • Sound

The sound circuit is located on page two of the schematic near B- and C-1,2,3. Q4 (2N3643) and surrounding resistors and capacitors R38, R36, S24, and C29 comprise a noise-generating circuit. Noise output should be around 100 MV. B10 is a band pass network with the second half of B10 used to amplify the desired frequency range. The output at B10-10 is fed into B9-2. B9 is a NOR gate being used as a feedback amplifier. B9-1 is normally high and therefore the output B9-3 is normally at a low potential. When a low is placed on the cathode of D2 capacitor, C3 (1 mf) is discharged through R4 and brought to near ground potential. At this point B9-1 is low and the amplified sound of B9-2 is allowed to pass through the MOS gate. This gate can be thought of as an analog gate, since a normal NOR gate would not pass an analog signal. C3 immediately begins to charge up through R3 and the point B9-1 begins to rise in potential. The effect of B9-1 rising in potential is to diminish the amplitude of the output at B9-3 until B9-1 reaches a high enough level; at this time it causes a solid low at output of B9-3. This output is summed at the input of the LM380, A9, and is used as the distant explosion (no aircraft hit) sound. In a similar manner, the explosion (direct hit) is brought through B9-9 to B9-10 after one more stage of amplification. The control, however, is the same at B9-8 as it was at B9-1 for distant explosion.

2-6

Page 19

The missile whistle is caused when the missile is fired. D9 is a free-

running oscillator (555) whose output to C19 is a triangular wave with a period of 60 ms. This output is fed into the 566 (C9) pin 5. The oscillation of C9 depends on the RC time constant between R26 and C18. However, if the side of R26 labled MISSILE WHISTLE is low, the oscillator will not function and there will be no output at C9-4. When a missile is fired and throughout its flight, MISSILE WHISTLE goes high enabling the 566 (C9). The output of this device is a triangular wave that starts out at a period of about .5 ms and extends to a period of about .9 ms at the end of the firing sequence.

  • Power supply The power supply is a standard on-board full-wave rectifier using an LM323 voltage regulator for the 5 VDC power supply. The negative supply also uses a full-wave rectifier (D12 and Dll) with a 5.6V zener across a 1000 uf capacitor to provide -5.6V at 4 ma.

1¢. Video mixing The video mixing network located at A4 and -5 on page 1 of the schematic resistively sums the different video wave forms to one common node and then passes them on to the video monitor through video cap.

2-3. SETUP PROCEDURE

  • Game time

The game time pot is located at D-9 on the PCB and is labled "play time." Looking down the board toward the edge connector, the play time is increased by turning it clockwise. The normal game time should be between 99 and 100 seconds. This is achieved by turning the pot to its center position and timing the game. Then turn the pot in the correct direction until proper game time is achieved.

  • Volume control

The volume control pot is located at A-9 on the PCB. Looking down the board toward the edge connector, the volume is increased by turning the pot counterclockwise. Adjust volume to desired level.

2-7

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21
  • CUSTOMER SERVICE INFORMATION

3-1. TEST EQUIPMENT

In ordér to test any Atari PCB, some items such as the logic probe are absolutely essential. Others are desirable and will make the test procedure easier but are not absolutely essential. Some of these instruments are available from the Atari Customer Service Department and are: the Kurz-Kasch 520 Logic Probe, the Atari Video Probe, and the Hewlett-Packard 10529A Logic Comparator. Other instruments that are very useful are the HP 10526T Logic Pulser and the Tektronix 465 Oscilloscope. These items are available through your local electronics supply house.

3-2. REQUIRED EQUIPMENT

The following items are essential to perform the test procedures presented in this manual:

  • Logic probe: This instrument is designed for checking the outputs of integrated circuits. The Kurz-Kasch Logic Probe, Model No. LP-520, which is available through the Atari Customer Service Department or most large electronics supply houses, is recommended. This logic probe indicates if a signal is a logic high, logic low, or changing from one state to another. Consult the operating instructions included with the probe for further details about its operation.
  • Video probe: This probe is a very simple but extremely useful device and consists of two test clips, a length of rubber-coated, test lead wire, and a 4.7K, %-watt carbon resistor. Video probes may be obtained from the Atari Customer Service Department or, if necessary, they can be assembled from standard components available at all electronics supply houses.

3-3. OPTIONAL EQUIPMENT

It is possible to find 90% of the possible PCB computer malfunctions without the following items. However, if a complete set of troubleshooting equipment is desired, Atari recommends the following:

Page 22
  • Hewlett-Packard 10529A Logic Comparator This device is used to verify correct IC operation. It simply clips onto in-circuit ICs and instantly displays any logic state difference between the in-circuit test IC and the reference IC in the comparator. Logic differences for each pin of a 14 or 16 dual in-line package are indicated by a lamp on the comparator. If the logic comparator is purchased from the Atari Customer Service Department, it is shipped with 20 preprogrammed reference PCBs. If the device is purchased elsewhere, these PCBs must be specially programmed.
  • Hewlett-Packard 10526T Logic Pulser This device is used to stimulate in-circuit ICs so that they are driven to their opposite states. This device is available from the Atari Customer Service Department or can be obtained from most large electronics supply houses.
  • Tektronix 465 Oscilloscope This oscilloscope is used for viewing various wave forms and should be ordered from Tektronix. Consult the manufacturer's operating instructions for details on oscilloscope operation.

3-4. TROUBLESHOOTING

The first step in any troubleshooting procedure is to observe the characteristics of the malfunction. With these clues in mind, examine the areas of the machine that might cause these symptoms. For example, if there is no power, check the harness -- not the PCB. Likewise, if part of the playfield display is missing, check the PCB -- not the harness or TV. Three major areas of the game can be isolated for troubleshooting purposes: the TV, the PCB, and the harness. The harness includes the fuses, the transformer, the interlock switches, the AC line filter, the start and coin switches, the antenna wire, the potentiometers, all plug-in type connectors, the PCB edge connector, and all the interconnecting wires.

  • Substitution: Substitution of parts is a legitimate and easy way to troubleshoot the machine. For instance, if you suspect a PCB malfunction, try substituting another known-to-be-good PCB. To check the TV monitor

3-2

Page 23

by substitution, connect the malfunctioning game to a known-to-be-good monitor, Harnesses are checked by elimination. Substitute a good TV and PCB, and if the malfunction persists, the harness must be at fault.

  • Other troubleshooting tips: If you have only a TV raster* and you want to determine if the PCB or the TV is causing lack of video display, try the following test:
  • Disconnect the PCB edge connector;
  • Turn the brightness and contrast all the way up; (ce) Touch video input to TV, pin 10 on PCB edge connector. If your TV monitor is functioning correctly, you will see faint black bars or "hum bars" on the screen.
  • Troubleshooting by symptom:
  • No power: Check for correct line voltage. If correct, check fuses and interlock switches. If these are alright, check transformer primary, which should show line voltage. Then check transformer secondary (pins 3 and 21), which should be 10 VAC with respect to ground.
  • Game credit shuts off: Try cutting the antenna wire shorter in inerements of 1-2 inches.
  • Game credit shuts off and/or TV picture shrinks: Check line voltage with VOM and be aware that a large motor nearby (such as an air conditioner) may drop line voltage when starting up.
  • No picture or raster: Check to see if TV connector is plugged in; check for line voltage at TV, and whether the latter's AC voltage switch is set to correct position. Check TV fuses and brightness control.
  • TV raster only: Check harness and especially the PCB edge connector. Check PCB and TV. (£) Picture rolls: Adjust TV vertical hold. Check or replace PCB.
  • Picture is wavy: Adjust TV horizontal hold. Replace transformer. Check harness, particularly grounds, 5-volt supply, and 73-volt regulator.
  • Picture is broken into diagonal lines: Adjust TV horizontal hold. Replace PCB.

%a TV raster is a blank but lighted TV screen with the brightness turned all the way up

3+3

Page 24
  • Jerky plane motion: Replace appropriate potentiometer.
  • No game credit: Check coin mechanism and switch, and the harness. Replace PCB.
  • Game sequence incorrect or parts of playfield display missing, distorted or not functioning: Replace PCB.
  • No audio: Check volume control, speaker connections. Replace PCB.
  • White picture but no display: Check edge connector on logic PCB, 5-volt supply from monitor, and 12-pin Molex connector on monitor.
  • No firing: Check firing buttons and harness connections.
Note: If the above checks do not solve the problem, consult the appropriate theory of operation description of the logic PCB circuits.

3-5. PCB SHIPPING

Careful packing of PCBs and other parts being returned to the factory is recommended, as Atari cannot be liable for items damaged in transit. If possible, include a short statement describing the problem encountered with the game.

3-6. LOGIC TYPE AND FUNCTION

TYPE FUNCTION

7400 quad 2-input NAND gate 7402 quad 2-input NOR gate 7404 hex inverter 74S04 hex inverter 7408 quad 2-input AND gate 7410 triple 3-input NAND gate 7413 dual NAND Schmitt trigger 7420 dual 4-input NAND gate 7425 dual 4-input NOR with strobe 7427 triple 3-input NOR gate 7430 single 8-input NAND gate T7448 BCD-to-7~segment decoder 7450 dual AND/OR gate (inverter/expander) 7474 dual-D flip flop 7483 4-bit full adder

3-4

Page 25

(Logic type and function, cont.)

TYPE 7486

7499

7492

7493

7407

74153

74157

74165

74192

74193

L380

NESSS

NES66

RCH136D

MFO60u0

8098

8103

8099

9311

9312

9314

9316

9321

9602

74186 FUNCTION

quad exclusive OR gate

decade counter

divide-by-12 counter 4-bit binary counter dual JK M/A flip flop dual 4-bit multiplexer quad 2-input data selector/multiplexer parallel-load 8-bit shift register synchronous decade up/down counter synchronous binary up/down counter amplifier timer

function generator

dual operational amplifier quad operational amplifier voitage-controlled operational amplifier hybrid hybrid hybrid one-of-sixteen decoder/demultiplexer

8-input multiplexer quad latch 4-pit binary counter dual one-of-four decoder

dual monostable multivibrator

ROM

3-5

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

ASSEMBL TOP ASSEMBLY ANTTATRCRAFT.

PARTS LIST SPECIFICATION Page_1 of _2 PO i A F —o- ( A. ATARI Innovative leisure Drawn

Description Prototype Rel

i ok ev per ECN_10390 p-12-75 — a OS [i [Rev per ECN 1439 Serpe >} —_ +] F perme eon eet [ors FT Part Number Qty. DESCRIPTION

1A0030271Assy, Cabinet
2A0030461Assy, Electronics Tray
3A0030481Assy, Control Panel
4A0036371Assy, Coin Door (Airtronics)
5A0015081Tllun. P.C. Board Assy.
6Ag00g511P.C. Board Assy.
7A0031021Assy, Florescent Light 18"
80030531Retainer, Upper Plex
90016561Bezel
100030521Plex Screen
a92-0061T.V., Motorola (XM 501), 19”
1271~21121Lock, Mech., Barrel Cart.
1374-36204Spacer 1.25"
140027282Panel Mtg. Bracket
150030511Retainer, Control Panel
160008631Grill, Speaker
lv48-0041Speaker, 5" Arkay#P50C5
1873-770014Pop Rivet
190011411Foam Pad (.75)
2074-36081Spacer, Tubular, (Non-Threaded), .50 Lg. Brass
2182-8116B3Button Head Socket Cap Screw, 10-24 x 1" Lg. Black
2272-51202Screw, Machine, Hexagon Head, 10-24 x 1x" Ig.
2375-2824S4Screw, Mach, Phil, Rnd. Hd., #8-32 x 1. 50" Lg.
2475-0484Washer, split Lock #8
2575-91854Nut, Hex, #8-32
2675-01884Washer, Flat #8
2772-66284Serew, Sht. Met., Pan Hd, Phil #6 x 1. 75" Le.
2872-66161Screw, Sht. Met., Pan Hd, Phil #6 x 1. 00" Lg.
2972~68126Screw, Sht. Met., Pan Hd, Phil #8 x .75" Lg.
3075-55 20B2Bolt, Carriage # %-20 x 1.25" lg. Black
3175-010S10Washer, Flat,-#10
3275-04010Washer, Split-Lock, #10
3375-911S8Nut, Hex, #10-24
3475-9312Nut, Wing, #10-24
3575-5128B6Bolt Carriage #10-24 x 1.75" Lg. Black
36 | * 70-304118" Florescent Tube, F15T12
370030541Instruction Plate
3875-01582Washer, Flat, %
3975-0452Washer, Split Lock, *%
4075-9352Nut, Wing %-20
NOTE: P/N 70-303,18" Fluorescent tube,F15T8 Can be used as an Alternative.
Page 28

ASSEMBLY TITLE ny P/L oo3026 a PARTS LIST. SPECIFICATION [rage 2 of 2 | [Part Number _|gty.||__ DESCRIPTION

003753-01 CRT Decal - Right Side 003754-02 CRT Decal - Left Side 003903 Bezel Shim 72-6608 Screw, SM, Pan Head, Phil. #6 x .50 Lg.

Page 29

PRODUCTION REL ROWSE Pee ECON 1042 REVISE PER, ECN L054 [Rese PER EON ICAO REV. PER GCN 1439 REV. PER ECN L4GL

Z S . ANAAAAARANRARURURSNRARAARARARRRANRS:

verenrany Ts a remus ies ATARL INCORPORATED 1440 Winchester Boulevard iecKED Lexus, California 95030, PREREI Lm {as TOP ASSEMBLY —— ANTIAIRCRAFT a [ASos0ze a tara "=

Page 30

[assemery trTLt 7 pyr rarecrat eLectronrcs Tray assP/L 003046 PARTS LIST SPECIFICATION ate = Mech. Eng. 4 dag Rev. Des ription Protitype Release

» rot Part Number DESCRIPTION

10030471Tray, Electronics
2A0030931Harness
30015511Trans former
47932011Fuse Holder
546-201101Fuse
690-30011Filter, Power Line
768-0011A.C. Power Interlock Switch
800a68]Bracket, Switch mtg,
954-4011Power Cord, 8!
10AOdI 9201Harness, Voltage Selection
Wy*A001921-011Shorting Block, 95V
12*A(D1921-021Shorting Block, 110V
13 | *A001 921-031Shorting Block, 220V H
1478-250024Screw Down, Tie Wrap
150006221Cover, Transformer
1672-660822Screw, SM, Pan Hd, Phil #6x1/2 1g.
17002898-031Int. Switch Harness
1g | *A00L921-041Shorting Blcok, 220V L
  • Install shorting blo¢k per voltage required
Page 31

“Ol*, 95V ("") ~O, uov (12) -03 , 22ovu() ~04 , 220 (6)

ATARI INCORPORATED 14600 Winchester Boulevard Los Gatos, California 95030

ASSEMEL+r, BECTRONWICS TeAy

Page 32

FLOURESCENT

CREDIT

START

PUSH BUTTONS

GUN POSITION ATARI INCORPORATED 14600 Winchester Boulevard Los Gatos, California 95030

me ANT/- AIRCRAFT

ELECTRIC DWG

c |”"""00300! B SHEET \ OF

Page 33

ANTIAIRCRAFT - MAIN HARNESS P/L ao03093

PARTS LIST SPECIFICATION pa Loft Drawn

Innovative

a pee Bee NE ef a a | A ee ee ee en es ee ee

Part NumberQty.DESCRIPTION
179-5111221Edge Connector, 22 pin
279-0103Solder Lug #10
379-07320V2Faston #187
478-240037Tie Wrap, Screw Down Type (SSC2S5-510)
579-5110012Connector Key
678-25001A/R Tie Wrap
778-28004A/R Flat Shrink Tubing
979-580282Connector, 3 position (F), Molex #03-09-1033
1079-580301Connector, 6 position (F), Molex #03-09-1063
1179-580361Connector, 12 position (F), Molex #03-09-1122
1279-58026]Connector, 12 position (M), Amp #1-480708-0
1379-202147Connector, Socket Amp #350550-1
1479-2020121Connector, Socket Molex #02-09-1118
1851-11844A/R Wire, 18 AWG, Yellow
1651-11866"seBlue
751-11859"""Green/White
1851-11800"""Black
1951-11899id°"White
2051-11855":”Green
2151-12077""20 AWG Violet
2251-12095:?:White/Green
23§1-12033""‘Orange
2451-12044"""Yellow
2551-12096"""White/Blue
2651-12000"""Black
2751-12097"""White/Violet
28§1-120552:xGreen
2951-12099""uWhite
3051-12088"""Grey
3151-12090""20 AWG White/Black
32§1-12011"""Brown
3351-12022"”Red
3451-12093""White/Orange
51-12066""Blue
Page 34

[assemsiy oie 7 runuarnum BOARD HARNESS AA P/L.aoosi00-03 PARTS LIST SPECIFICATION Page 1_of } Drawn Checked 777. 3/24 Mech, Eng. Proj. Eng. Sree REV. B

bt a¢ Innovative leisure

Part Number DESCRIPTION

179-580271Connector, 3 position (M) Body #03-09-2032
279-580272Connector pings Molex #02-09-2118
(351-12044A/R| Wire, 20 AWG, Yellow
478-25001A/R| Tie Wraps
Page 35

AA FLOURESCENT LIGHT HaRNess —P/L Ao03100-01 NM PARTS LIST SPECIFICATION Page 1_of \ check eae ATARI Checked 7, S2el Pr Mech. Eng. Innovative leisure

DESCRIPTION

179-580431Connector, 2 position, (M) body Molex #03-09-2022
279-580272Connector Pins, Molex #02-09-2118
351-11800A/R | Wire, 18 AWG, Black
451-11899A/R| Wire, 18 AWG, White
578-25001A/R | Tie Wraps
Page 36

D a Rev_per ECN 1267 3=2— AAR 4 cn _ Z4 es ee I ES RO OO NN RE

DESCRIPTION

79-58037 79-58027

79-07220V 78-28004 78-25001 78-24003 51-11859 51-12077 51-12044 51-12096 51-12000 51-12097 51-12099 §1-12022 51-12066 51-12011 Connector, 12 position, (M) body Molex #03-09-2121 Connector pins Molex #02-09-2118

Faston #110x20 Female Shrink Tubing Tie Wraps Screw down tie wrap (SSC2S-S40) Wire, 18 AWG, GN/W "20 AWG, Violet Wire " "Yellow " " "White/Blue u “Black " " " White/Violet 0 nom White " non Reg " "0 Blue Brown

Page 37

mca OOlECSY, ODM SSreT-ae Searessy,,, | mers von | 06056 muon “199 07 iam 12504 00941 GaLVAONIOONI TEVIY "OWONS SY AAD ctvam aLL Fed mazes sTSc "aed Pouscwaal dO ane AL 109 ae Loa OlLles Wee Caprese Bay snoisnand *

  • Salon = a 9 §9bSa330 -avd9reg i i FZ aie 17a Ore Ss Pee ; E=e Tee Coes] y Ey, 6.0 Swe Nowanosae “va ww aS

& [roca [SO-COIGCOY ssanaym dew [| oat JO0-OO1GOOY SSanavn Ann 1inNsessany ZO-ONGOOY SSSreNn TBC ACALNOF

Page 38

FPoOwuanrwonr ° A. ATARI Innovative

Description Pi eeesupe na | Prop ep

003049 62-009 001856 62-002 003050 A003100-02 72-6608 75-51 24B 75-030S 75-9118 NNN WHER IOH DESCRIPTION

Panel, Control Switch, Push Button, Licon 76-7151 ‘Bushing, Switch Switch, Push Button, Panel, MIG., LED Illum. Board, Control Assy, Harness, Control Panel Screw, Sht. Met., Pan Hd, Phil, #6 x % Lg. Bolt, Carriage, #10-24 x ls Lg., Black Washer, Flat, Wide Pattern, #10 Nut, Hex, #10-24

Page 39

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 40

Peep cee SOEs [REV PER ECN [266 |e

BS ATARI INCORPORATED 14600 Wicheter Boulevard LosGator,Caforni 95020,

ASSEMOELY, cole COUTROL PANEL Rear ATARI

[ec

Page 41

Innovative leisure

19-311103 19-311105 19-808W4PO 21-101104 21-101224 24-060227 24-100105 24-100106 24-100107 24-100225 24-100226 24-100475 24-100476 24-160108 24-160477 24-160808 27-101102 wore

PRPEBPENBRPHPOoFt PARTS LIST SPECIFICATION Page 1 of 2

i Oe ee

100 ohm, XW, 1K ohm "

""10K ohm " "
""1 Meg " "
""15K" "
""150K" "
""180 ohm " "
""180K" "
""220 ohm, " "
""22K ohm, " "
""220K ohm," "
”W270K ohm," "
""330 ohm, " "
""33K ohm, " "
""3.9% ohm," "
""4.7K ohm," "
""47K ohm, " "
""470K ohm," "
W"56 K" Ww
""560K" "

" 2.7 ohm, " 5%

""9.1K" "

Trim Pot, 10K ohm Trim Pot, 1 Meg Resistor, Wire Wound, 4 ohm, 10W Capacitor, Mylar, .1mfd Capacitor, Mylar, .22mfd Capacitor, Electrolytic, 220mfd, 6V

"m1mfd
8"10mfd, 10V
Wyut100mfd, 10V
".2.2mfd
""22mfd
""4.7mfd
ad747mfd
:"1000mfd, 16V
""470mfd, 16V
""8000mfd, 16V

Capacitor, Ceramic, .001mfd Comp, 1,

Page 42

ASSEMBLY TITLE

27-101103 27-120104 28-101101 29-013 31-414F 31-1N914 31-1N4001 31-1N752A 34~2N3643 33-2N3644 37-7400 37-7402 37-7404 37-7408 37-7410 37-7413 37-7420 37-7427 37-7432 37-7448 87-7450 37-7474 37-7485 71-7486 37-7490 37-7493 37-74107 I37-74153 37-9312 37-9316 7-9602 37~556 37-566 8 7-LM380 7-747 7-4001

B7-LM323 p9-001 pO-101 p4-100505

603127 O62992 Litem | Pare Number Joey. ]

©

oo

i) PRR RP PWRPw®RIWOFOANP HEE PN EN OOP HE EHP wONNrnen w

=A PNNPEE ANTI-AIRCRAFT IT PCB

PARTS LIST SPECIFICATION

DESCRIPTION Capacitor, Ceramic, Capacitor, Ceramic Bypass, .1mfd Capacitor, Dipped Mica, 100pfd Capacitor, Tantalum, 100mfd, 10%, foV Diode, 414F

Transistor, Transistor,

Crystal, 14

PC. Koaep Diode, 1N914 Diode, 1N4001 Diode, 1N752A Zener

Integrated Circuit, 7400 " "

Voltage Regulator, LM323 Switch, Slide, PC Mount, DPDT

Capacitor, Plectrolytic, Smfd Resistor, 27K, kW, 10% Program, Anti-Aircraft Target P/L o00951 Rev B es | ree

-Olmfd

2N3643 2N3644

7402 " 7404 " 7408 " 7410 " 7413 " 7420 " 7427 " 7432 " 74U8 " 7450 " 7474 " 7485 " 7486 " 7490 " 7493 " 74107 " 74153 " 9312 " 9316 " 9602 " 556 " 566 ” LM380 ” 747 4901

MHZ

Page 43

MoD ©

Ke tnt

tnd

CE ) 0 QUT M

@& tt ES 2a ooain— [S

> 6

Mop 20 ’ x a com view

evi

Is 7450

if 17485 74.85 A, s)

i le ti 7455/31 0

MOD T

MOD ©

[+ 8000 uf

ALL DIODES ARE IN9I4,, EXCEPT AS NOTED. DESZEIPTION TG PEDDOCTION RELEASE iaahteal Ps imal a REVISED PER EQN 1145S

MODIFICATION List

lL. Cor TRACE TO HS PINT Ou BOTTOM OF BORED NEAR PIN.

  • Cor BOTH TRACES TS HO PIN 12 ON BOTTOM OF BOARD NEA PIN.
  • Cor Teace To AZ pin 2 ON TOP OF BOARD.
  • Cot tRace To AZ PINS ON TOP OF BOARD. S. Cor Teace TO AZ PINZON BOTTOM OF BOARD NEAR PIN. ©. BON A JUMPER FROM PLATE THED HOLE BY C43 To B50, AS SHOWN.
  • RON A aUMPER FROM 253 TO LS PINS 12 €13,AS SHOWN.
  • Jumper LO PIN 11 TO HS PIN 1. S. Bun A JUMPER FROM BSO To NS PINS 2 & 3, AS SHOWN. (0, JoMPER NO PIN 1 TS HS Pin IB.
  • Cot uD LIFT PIN 1 OF AZ, 12, BOM A JUMPER FROM LIFTED PIN 1 TO Le PIN 4. 13, JOMPER FS PIN IB To AZ PINS.
  • JUMPER Al PIN 1S To AZ PIN 10. 1S, Jumper AZ DIN 2 To AZ PIN 8B. le. JUMPER AZ PINS TO BI PINT. 17, Jumper AZ PIN 13 To BI PINS.
  • Cur Teace To BI DINZ ON BOTTOM OF BOARO. 1S, JomPER OI PINZ TO BI PING, 20, Zon A AWMPER FROM PLATE THRU BETWEEN JI AND J2 TO 32 PIN 4S SHOWN.

Nove: Asove MosiFicaTions WILL BE MADE TO ALL i Revision "A PC. Bones (0022902). Assemare BBISION WiLL BEA,

When @evision "B” PC. Bones ARE RECEIVED, BOARDS WILE BE STOFFED AS SHOWN , WITHOUT THE MODIFICATIONS, Asxemauy REVISION WILL BE "BI

ATARI INCORPORATED 14600 Washester Boulevard os Gatos, California 95020 ATARI wu ASSEMBLY ANTI-AIRCRAFT IL

ip "AC0O951 | “AST oor | wy

Page 44

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 45

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.