Tech Romancer
Tech Romancer (Europe 980914) (Capcom, 1998) · Manual · 16 pages · 14 sections · original scan
©CAPCOM CO, LTD. 1998, ©CAPCOM USA, INC. 1998 ALL RIGHTS RESERVED.
OPERATORS MANUAL
WARNING
This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.
TEC1300 102198
GCAPGON* co-op, inc. TECH ROMANCER™
THANK YOU FOR PURCHASING TECH ROMANCER ™ WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:
CAPCOM® COIN-OP, INC. ATTN: CUSTOMER SERVICE 475 OAKMEAD PARKWAY SUNNYVALE, CA 94086 PHONE: (408) 522-5333 FAX: (408) 522-5331
THE SERIAL NUMBERS OF YOUR GAME ARE LOCATED ON THE PRINTED CIRCUIT BOARDS AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.
PLEASE RECORD THE PC BOARD SERIAL NUMBERS HERE:
- LOWER PC BOARD - SOLDER SIDE: AAMA SERIAL NUMBER:
- LOWER PC BOARD - COMPONENT SIDE: CAPCOM SERIAL NUMBER:
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
® CAPEEI coin-op, inc TECH ROMANCER™
TABLE OF CONTENTS
Warranty Information ii
Kit Inspection, Kit parts List
Kit Installation Preparation Installation Marquee Control Panel Overlay Control Panel Component Cabinet Decals PC Board Installation System Wiring Control Panel Test/Volume Bracket Speakers Q-Sound Modification PC Boards owonnynynyny wo
ok RA
Test Menu & Game Adjustments Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions Configuration Menu System Configuration Game Configuration CMHARAMAD
Reference Information JAMMA Connections Auxiliary Cable Connections
Please read the following instructions to keep the PC boards in good condition:
Do not drop or bump the boards. Do not spill any liquids on the boards.
DISASSEMBLING THE BOARDS OR REMOVING STICKERS MA CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY.
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CAPCOM co-op. inc. TECH ROMANCER™
LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)
CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:
A. Printed Circuit Boards: Ninety (90) Days B. Electronic and Mechanical Components: Ninety (90) Days
No other part of Seller's products are warranted.
Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.
Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:
A. Seller is notified promptly upon discovery by buyer that stated products are defective;
B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.
This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.
WARRANTY DISCLAIMER
EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.
ii Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
® CAPCOM co-op, inc. TECH ROMANCER ™
KIT INSPECTION
Check that all of the following parts have been shipped with your lat. If any parts are missing, contact your distributor
DESCRIPTION Assy, PCB, PSX System, “TECH ROMANCER” Standoff w/Screw, PCB Mounting Harness, Stereo Speaker Cable, Auxiliary Marquee, “TECH ROMANCER” Decal - Top, Game Play Inst., “TECH ROMANCER” TEC2520-02 _| Decal - Bottom , Game Play Inst., “TECH ROMANCER’”
TEC2510 Decal, Joystick & Button Switches, “TECH ROMANCER” TEC1300 Manual, Operators, ‘TECH ROMANCER” ‘AWO00147 Decal, Cabinet Side GE1200 Monitor Card ‘AW00216 Overlay, Control Panel GE2030 Joystick, 8 Way 16-0130 Switch, 1-Player Start Button (White) 16-0131 ‘Switch, 2-Player Start Button (White) 16-0133 Switch, Button Red) 16-0134 Switch, Button Blue)
PL00376 | Plex, Marquee, Clear, 27.0x 9.0x U8”
Switch, Button (Green) ‘Switch, Button (Yellow) g > 44444444448 Vv ST] V v V v V V V V v Vv Vv Vv V mp ap a> A Lele) lel ete} mle} el ele} ee} el] el} ala
2{ 2] 4] 4[ 2]
Proprietary and confidential information. not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CAPCOM co-op, INC.
KIT INSTALLATION
MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.
PREPARATION
- Disconnect and remove the old printed circuit board(s) from the cabinet.
- Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
- Remove any covering from the control panel overlay, and then remove the control panel overlay.
- Determine where any new holes should go. Center punch any needed new holes on the control panel.
- Cut out the new holes using a 1-3/16" hole saw.
- If there is an additional control panel cover, Figure] (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *Cover is not included in the kit.
- Plug up unused holes with a wood dowel (1-1/8" diameter) and sand any rough edges.
INSTALLATION
Marquee Installation
- Remove the marquee plexi glass, marquee overlay, and the cabinet graphics.
- Install the new marquee and replace the plexi glass. Clear plexi glass is included in “Full” kit.
Control Panel Overlay Installation (See Figure 1)
- The contro] panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
- Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges. TECH ROMANCER™
- Trim any excess from the overlay. Place the drill hole template on top of the overlay. aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
- Peel off the backings of the 4-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
- Install the control panel cover, FIG.1. (if required).
Overlay (Trim to size)
Figure 1: Overlay Installation
Re-assembly of Components
- Notice that there are two white buttons. See Figure 2. The WHITE buttons are START buttons. Install the PLAYER ONE button on the top left-hand side of the control panel, and the PLAYER TWO button on the top right-side of the control panel.
a)
ia
Figure 2: Start Buttons 1 Player 7 2 Player QS (2 5 ia
= Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
© CAPCOM" coin-op, inc. TEC ROMANCER™
Red Green Blue Red Green Blue
Yellow Yellow
Buttons
cen cm — es BS Bs
~
Figure 3: Control Panel Buttons and Switches ‘Switches
- _ Installall buttons and retaining rings on the control panel as shown in Figure 3. Install two RED butonsto the immediate right of each joystick, install two GREEN buttons to the right of the redones.
- _ Install the switches on the buttons as shown in Figure 2. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
- Install the joysticks on the control panel as shown in Figure 4.
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CABINET DECAL INSTALLATION
- Removemonitor glass and install monitor card
- Peeboff the backing to the instruction decals and place on both the top and bottom of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides ofthe cabinet.
INSTRUCTION DECAL
Figure 5: Cabinet Decal Installation
CONTROL PANEL WIRING
- Reconnect the existing JAMMA connectors to the control panel according to the chart in Page 10.
- Connect the Player 1 and the Player 2 KICK buttons to the auxiliary cable harness as shown in Figure 6. Make the connections according to the chart in Page 10. To PC Board ‘Connector CN2
® CAPCOM co-op, inc. TECH ROMANCER™
TEST/VOLUME BRACKET WIRING
- An optional Test Switch bracket (see Figure 7) is available through your distributor. (CAPCOM Part number 03-0050). Your cabinet may already contain this bracket. When installing, the bracket should be mounted inside the coin door and on top of the cash box for easy access.
Volume adjustments must be made through the volume control knob located on the PC board.
Figure 7: Test Switch Bracket
Wiring of the Test Bracket requires connections to the main JAMMA harness as shown in Table 3:
COLOR FUNCTION TO 7OLUME-UP. :2NO.CONNECTION: : ‘(NO CONNECTIO! VOLUME- DOWN 2. ae COMMON _ NO.CONNECTION “TEST -JAMMA “15” JAMMA “A” or “B” or “e” or “f” or “I” or “2” or “27” or “28” BLAC.
GREEN BROWN
BLACK GROUND
Table 3: Test Bracket Wiring Chart
SPEAKER WIRING
24a.If you are converting a cabinet that is not equipped with CAPCOM® Q-SOUND, the leads from the speaker harness (supplied with this kit) must be wired to the cabinet speakers according to the TABLE 4. WHITE GRAY BROWN ORANGE
Table 4: Speaker Wiring Chart SPEAKER (TERMINAL LEFT (+) LEFT (-) RIGHT (- RIGHT (+)
24b.If you are converting a cabinet that is equipped with CAPCOM® Q-SOUND, you may elect to wire directly to the cabinet speaker terminals, as shown above, or you can obtain the same result by performing the following modification (see Figure 8):
- Disconnect the speaker harness connector from the Q-SOUND board at location CB8.
ii) Install a 4-pin, 0.156 inch diameter header connector (not supplied with this kit; purchase locally) onto the speaker harness connector.
iii) Insert each wire lead from the supplied speaker harness to each corresponding pin from a 4-pin, 0.156 inch diameter female connector (not supplied with this kit; purchase locally).
iv) Push the female connector and the header connector pins together.
- Your cabinet is now equipped to receive stereo sound from the PC board.
TO CABINET SPEAKERS.
EXISTING SPEAKER HARNESS CONNECTOR
TO GAME PC BOARD, LOCATION
CONNECTOR
SUPPLIED ‘SPEAKER HARNESS
Figure 8: Q-SOUND Modification ‘e030
4 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
Cy CAPEOM" coin-op. inc.
PC BOARD INSTALLATION
- Install the four (4) mounting standoffs to the underside of the PC board by securing with the supplied machine screws. Then, fasten the PC board standoffs to the control panel shelf with wood screws, as shown in Figure 11.
Wood Screws are not included in the kit.
‘WOOD SCREW
- —_. . STANDOFF
Figure 9: PC Board Mounting
PC BOARD WIRING CONNECTIONS AND ADJUSTMENTS
- Connect the JAMMA harness connector to the edge connector located on the bottom PC board (see Figure 10). TECH ROMANCER™
WARNIMG
IMPROPER INSTALLATION OF THE JAMMA HARNESS CONNECTOR TO THE PC BOARD WILL CAUSE DAMAGE TO THE PC BOARD.
- Attach the auxiliary cable connector to the top PC board at location CN2 (see Figure 10).
- Attach the speaker harness connector to the PC board at location CN504 (see Figure 10).
- Check that the mode switch, on the lower PC board, is set to “STEREO” (see Figure 10).
- Check that all 4 positions of the DIP switch are set to OFF (see Figure 10).
- Power-up the game and adjust the speaker volume by turning the Volume Control knob clockwise to increase volume, or counterclockwise to decrease volume (see Figure 10).
- Set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.
Figure 10: PC Board Wiring Connections & Adjustments
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
® CAPEOL co-op, inc. TEC ROMANCER™
TEST MENU The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin door or switches, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.
- ACCESSING THE TEST MENU TEST MENU + Fora CAPCOM® cabinet, or a cabinet with INPUT pa apaniatieg Make sure the game ison and push the test switch. OUTPUT The screen shown left will appear. + Fora cabinet without a test switch: SOUND& VOICE You need install test switch to your cabmet. COLOR Please refer Page 4 for test switch installation. DOT CROSS HATCH
- HOW TO SELECT AN ITEM GAME DATA + Use the PLAYER 1 JOYSTICK to move the arrow in front of the desired item and press the CONFIGURATION PLAYER 1 SHOT 1 button, as shown below in various control panel configurations:
- CLOSING THE TEST MENU To close the Test Menu, highlight “9. EXIT’ and push the PLAYER I SHOT Ibutton. + Toretum to the test menu, push the PLAYER1 STARTand PLAYER 1 SHOT Ibuttons simultaneously. Player 1 Joystick Player 1 Start + The test menu will always retum to the screen:
- After you exit the “7. CONFIGURATION MENU” and
- After the memory is tested from the menu, “8. MEMORY CHECK’.
Player 1 Shot 1 Player 1 Shot 2 vieot (Attack A) (Attack B)
- TEST MENU ITEM DESCRIPTIONS INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “I” when depressed ar moved. OUTPUT ‘Used to test the com meter and the cai lock. SOUND & VOICE ‘Select a code of SOUND with the PLAYER 1 JOYSTICK Push the PLAYER 1SHOT1 button to hear the sound of the selected code. COLOR ‘Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum colar balance L and solid black background. DOT CROSS HATCH Used to test the screen size, focus and distortion. GAME DATA There is "Accumulated" and "Resetable" counters . In each Cain meter, Free play and Service switch counter will be displayed. See Page 7 for detail. —_| CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section. MEMORY CHECK Used to test memary. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If“NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if“NG?” still appears._ EXIT Select this item and push the PLA YER 1 SHOT 1 button to return to game play mode.
{ 6 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC
® CAPE coin-op, inc. TECH ROMANCER™ EE COIN-OP INC TECH ROMANCER™ | GAME DATA COUNTER
"ACCUMULATED DATA" ARE NOT RESETABLE BY OPERATOR.
- GAMEDATA "RESETABLE DATA" ARE RESETABLE BY OPERATOR
TO RESET DATA:
- ENTER TO TEST MENU BY PRESSING TEST SWITCH
- SELECT GAME DATA (MENUE NUMBER 6)
- READ AND MEMO COUNTER VALUE IF NECCESARY.
- PRESS IP START, SHOT2, SHOT3 AND SHOT4 BUTTONS AT THE SAME TIME.
- CONFIRM THAT RESETABLE DATA RETURNED TO ZERO.
- EXIT FROM GAME DATA DISPLAY BY PRESSING 1P START AND SHOT] RESETDATA=1PSTART& SHOT2& SHOT3&SHOT4 AT THE SAME TIME.
EXIT=1P START & 1P SHOT1
CONFIGURATION MENU
The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB.
The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.
- CONFIGURATION MENU 1. | ACCESSING THE CONFIGURATION MENU %) SYSTEM . From the TEST MENU, move the arrow to
- GAME “7, CONFIGURATION” and push the PLAYER 1 SHOT 1 button.
- DEFAULT The screen left will be displayed. A description of each option is
- SAVESEXT explained in the table below.
SELECT 41PUPORDOWN START 1P SHOT1
- CONFIGURATION MENU ITEM DESCRIPTIONS
SYSTEM | Select this item to change settings for credits, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. Use this item to restore configuration settings to the original factory values. Press the DEFAULT PLAYER 1 SHOT 1 and PLAYER 1 SHOT 2 buttons at the same time to restore default values. SAVE & Use this to save new configuration settings and exit to the Test Menu. The message “SAVING EXIT NEW CONFIGURATION IN EEPROM’ will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears.
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
® CAPCOM co-op, ine. TECH ROMANCER ™ COIN OP ING TECH ROMANCER SYSTEM CONFIGURATION
7-1) SYSTEM CONFIGURATION CHANGING THE SYSTEM
| 4) COIN | 2COINS 1CREDIT | CONFIGURATION SETTINGS |
2)CHUTERMODE — 2CHUTESSINGLE
| 3) CONTINUE | ON | Move the PLAYER 1 JOYSTICK up or down to |
| 4) DEMOSOUND | (ON | highlight the desired option. Once the option is |
- DEMOSTAFF ROLL ON highlighted, move the PLAYER 1 JOYSTICK left or
- SOUNDMODE = JAMVA right or press the PLAYER 1 SHOT Ibutton to select.
- REGULATION
- EXT SELECT OPTION
MODIFY SETTING
SYSTEM CONFIGURATION ITEM DESCRIPTIONS
1LCOIN SELECT THE CHARGE PER PLAY. 2.CHUTER MODE SELECT THE NUMBER OF PLAYERS) AND OOIN CHUTES. 1CHUTESINGLE: WITHTHISSETTING, EITHER PLAYER CANSTARTTHEGAME. 2CHUTESSINGLE: TWOPLAYERS USE ONE OOIN CHUTE AND PLAY ATTHESAME TIME. THE PLAYER WHOSE OOIN WASPUTIN FIRST STARTS THE GAME. 2CHUTESMULTL TWOPLAYERS USETWOOOIN CHUTES AND PLAY SEPARATELY. ‘THE GAME STARTS FROM THE SAME SIDE AS THE COIN CHUTE WAS USED.
- CONTINUE SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY.
- DEMOSOUND TURNS ATTRACT SOUNDS ON OR OFF. 5.DEMOSTAFF ROLL | TURNSSTAFF ROLES ON OR OFF DURING THE ATTRACTION DEMO. DMODE "EXTERNAL' SHOULD ONLY BE SELECTED WHEN THE CABINET SPEAKERS HAVE BEEN CONNECTED TO THE GAME PC | B ons SEE PAGE 4, SPEAKER WIRING. SUA LUUS EXTERNAL QSOUND POWER AMPLIFIER IS NUT USED FOR THIS GAME. (GEE PAGE 6 FOR DETAILS) 7.REGULATION IF SET TO “ON” THE SCENES THAT ARE THOUGHT TO BE INAPPROPRIATE TO MORE SOFT EXPRESSION.
- EXIT ‘TOSAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH EITHER THE PLAYER 1 SHOT IBUTTONOR THE P!..1YER1 SHOT ZBUTION. SYSTEM CONFIGURATION OPTION SETTINGS
- COINMODE
| 2CHUTETYPE
ce 2 CHUTE:
6.S0U)
8 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
® CAPCOM coin-op, inc. TECH ROMANCER™
GAME CONFIGURATION
CHANGING THE GAME 7-2) GAME CONFIGURATION CONFIGURATION SETTINGS
| Mhiieenand | EASYT™#~HARD | Move the PLAYER 1 JOYSTICK up or down | |
| @ DAMAGELEVA. | LOWT~4~JHIGH | to highlight the desired option. | Once the |
| 3) TIMESPEED | FASTT“4“JSLOW | option is highlighted, move the PLAYER J |
JOYSTICK left or right or press the
- DAMAGE GAUGE(S)[CPU]
| ) | a | PLAYER 1 SHOT 1 button to select. |
- DAMAGE GAUGES) [VS] [2"]
- EVENT
DESCRIPTION OPTION SETTINGS
- DIFFICULTY SETS THE GAME DIFFICULTY LEVEL 2 3
- DAMAGE SETS THE OFFENSIVE POWER LEVEL. 3 LEVEL
- TIMER SPEED SETS THE SPEED OF THE TIMER.
RANGE FROM 1 TO 8. 1 BEING THE FASTEST
4.DAMAGE GAUGE(S) SETS THE NUMBER OF "DAMAGE GAUGE(S)" [VS. CPU] (LIFE) IN "VS. CPU MODE".
- DAMAGE GAUGE(S) | SETS THE NUMBER OF "DAMAGE GAUGE(S)" VS. PLAYER] (LIFE) IN "VS. PLAYER MOD)
- EVENT SPECIAL SETTING FOR TOURNAMENT EVENT. 1 MATCH: ONLY ONE CREDIT IS REQUIRED FOR A.2P GAME. THE GAME ENDS AFTER ONE MATCH REGARDLESS OF THE RESULT. RETURN TO THE CONFIGURATION MENU.
FACTORY SETTING.
L Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
Cy ICA'RCOM| COIN-OP, INC. TECH ROMANCER™
JAMMA Connections
SOLDER SIDE COMPONENT SIDE
GND GND GND 5 +5V DC +5V DC NIC. 2 +12V DC KEY KEY NIC COIN COUNTER 1 COIN LOCK 2 COIN LOCK 1 *SPEAKER (-) NIC. VIDEO GREEN VIDEO RED VIDEO SYNC VIDEO BLUE SERVICE (FREE CREDIT) VIDEO GROUND NIC DIAGNOSTICS
| 2 PLAYER | - COIN | IPLAYER | - COIN |
| 2 PLAYER | - START | 1PLAYER_ | - START |
| 2 PLAYER | _- UP | 1 PLAYER - UP | |
| 2 PLAYER | - DOWN | 1 PLAYER | - DOWN |
| 2 PLAYER | - LEFT | LPLAYER | - LEFT |
| 2 PLAYER | - RIGHT | 1PLAYER_ | - RIGHT |
| 2PLAYER | -ATTACKA | IPLAYER - ATTACK A | |
| 2 PLAYER | -ATTACKB | 1PLAYER_ | - ATTACKB |
| 2 PLAYER | - JUMP | 1PLAYER_ | - JUMP |
NIC NIC NIC NIC GND GND
WIRE COLOR CONNECTOR ODD ROW CONNECTOR EVEN ROW WIRE COLOR
NIC NIC NIC NIC NIC NIC PURPLE/YELLOW NIC NIC NIC PINK NIC RED NIC BLUE PLAYER 1 GUARD GRAY/YELLOW PLAYER 2 GUARD PINK/YELLOW NIC NIC NIC NIC NIC NIC PLAYER 2 GUARD COMMON PLAYER 1 GUARD COMMON
10 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
® CAPCOM co-op, inc. TECH ROMANCER™
REFERENCE INFORMATION
PC BOARD CONNECTIONS AND CONTROLS
Auxillary Cable Test Switch Connector (Not Used)
NS Mode Switch
<& Volume Control Knob - Ma RS Speaker Harness ~_ Connector
TYPICAL CONTROL PANEL LAYOUTS FOR “TECH ROMANCER ™
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
WARNING
Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.
The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.
CAIRCOMYg COIN-OP, INC. 475 Oakmead Parkway Sunnyvale, CA 94086 Phone: (408) 774-0500 Fax: (408) 522-5331
Copyright © 1998 CAPCOM ® coin-op, inc., All Rights Reserved