CATHODE RAY TOMES

Hydra TM-354 1st Printing Universal Kit

Hydra (Atari Games, 1990) · Kit Manual · 56 pages · 51 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

ss fonts (wo Con Yeoie AL wZING FIL

  • 4300 MEADO SPACE #518 LAS VEGAS, BY, #® 9104

Hydra

Universal Kit Installation Instructions

Page 4

Copyright © 1990 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles, In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, Califomia 95036-1110

Printed in the U.S.A 5/90

Produced by the Atari Games Technical Publications Department. Technical Writing and Design: Andrea Dencker Illustration: Mary Ohanessian Sumner Hydra Universal Kit

Notice Regarding Non-Atari® Parts

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game. © Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. it has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMD ground cage, be sure that the game printedcircuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

Hydra Universal Kit

Contents

  • Installation How to Use This Manual .... Cabinet Equipment Requirements Tools Required Inspecting the Ki Preparing the Cabinet for the Kit Installation Assembling the Controi Panel Installing the Foot Pedal... Connecting the JAMMA Harness. Installing the Hydra Game PCB.... Installing the Bezel, Labels, Decals, and Attraction Assembly Setting the Coin and Game Options. Game Play 2 Self-Test RAM and ROM Test Entering and Exiting the Self-Test. Select Test Menu Statistics ... Coin Options Game Options - 2-4 Alphanumeric Test . 2-4 Motion Object Test 25 Switch Test . 2-5 Playfield Tes! . 2-6 Color RAM Test Convergence Test . Sound Test..... . 2-6 . 2-6 2-7 3 Maintenance and Troubleshooting Video Display Sync Problems - 3-3 X-Y Steering Control - 3-3 Foot Pedal Assembly 33 ROMs and RAMS. OO a] 4 Parts Illustrations See the list of illustrations that follows.

5 Schematics See the list of illustrations and list of tables that follows. Hydra Statistics Sheet Warranty Figure

Figure

Figure

Figure

Table

Table

Table Illustrations

1-2 Hydra Kit Parts Installed in Cabinet .... 2-1 Select Test Menu Screen. 2-2. Statistics Screen... 2-3. Coin Options Screen. 2-4 Game Options Screen. 2-5 Alphanumeric Test Screen. 26 Motion Object Test Screen 2-7 Switch Test Screen... 2-8 Playfield Test Screen 2-9 Color RAM Test Screen 2-10 Convergence Test Screen 2-11 Sound Test Screen.

4-1 Hydra Kit Parts List 4-2 XY Steering Control Assembly 4-3 Hydra Foot Pedal Assembh 4-4 Hydra Game PCB Assembl 4-5 JSA Audio II PCB Assembl 5-1 Hydra Game PCB Assembly Schematic Diagram 5-2 JSA Audio II PCB Assembly Schematic Diagram 5-3 Faulty RAM/ROM Tables

Tables

1-1 Equipment Requirement: 1-2 Contents of Hydra Kit.. 1-3. JAMMA Pin and Wire Connections. 2-1 Bad RAM Location by Error Address. 2-2 Bad ROM Location by Error Address. 2-3. Summary of the Self-Test Screens 2-4 Coin Option Settings... 2-5 Game Option Settings. 3-1 Troubleshooting Table. 3-2 Voltage Inputs and Test Points on the PCB...... 3-3 What ROM Problems Look Like. 3-4 Atari Games Video Connector Pin Assignments... 3-5 Screen Colors Indicating Bad RAMS

iii

Page 6

Hydra Universal Kit

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game unti] it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those re-

iv placed in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50

Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS,

AND WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions. ‘WARNING — Players and/or technicians can be killed or injured if instructions are not followed. rar
Page 7

CHAPTER 1

Installation

This manual provides information for installing, testing, and troubleshooting the Hydra™ Universal kit. The manual is divided

into the following chapters: Ml Chapter 1 describes how to install the Hydra kit in your cabinet. This chapter also describes the Hydra game play. Also included is the template for drilling the holes into the

How to Use This Manual

JSA Audio II PCB. control panel and into the cabinet front for the foot pedal. Ml Chapter 2 describes the self-test

and how to use the self-

test screens. Ml Chapter 3 contains troubleshooting and maintenance procedures. Ml Chapter 4 contains the kit parts list and parts illustrations. Ml Chapter 5 contains the schematics for the Hydra game PCB and

Page 8

Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements Table 1-1 lists the equipment required in the cabinet into which you are installing the Hydra kit.

Table 1-1 Equipment Requirements

‘Horizontal frequency: 5. Vertical rey ney: 60 Hz

‘Control Panel ‘Hydra Universal Kit

CAUTION Do not unplug or plug in the Hydra game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Tools Required ® Two C-clamps @ Drill with a 1/4-inch and 5/16-inch drill bits, a 1 3/4-inch hole cutter (or a 1 3/4-inch chassis punch), and a 1 3/16-inch hole cutter Phillips screwdriver Flat-blade screwdriver ® Socket wrench set and ratchet

1-2 m= 1/4-20 hex wrench ™ Wire cutters and strippers m Straight edge m Squeegee = X-ACTO™ knife m Insulated wire connectors (if you are installing a new JAMMA harness)

Table 1-2 Contents of Hydra Kit

Part No.Description=~“Quantity
72-07002#1/4 Fender Washer»8
7266128#6 x 3/4-Inch-Long, Pan- Head,4

Cross-Recessed Type-AB Screw ~ my

75-5112B#10-24 x 3/4-Inch-Long Black4
Carriage Bolt::
75-5520B#1/4-20 x 1 1/4-Inch-Lo:4

Carriage Bolt | =

038158-01Product LD. Label1
039450-01FCC Compliance Label1
047205-01Attraction Panel ‘Shield:a
047209-01Control Panel Cov.‘1
04785301Conwrol Panel Mounting Bracket1
047889-01Atiraction Panel Film:1
047890-01Control Pane! Decal1
047891-01Side Panel Decal.2
047892-0119/25-Inch Monitor Bezel1
141026-001-50-Inch ILD. Split Ferrite Bead2
160044-001Snap-Action 5ei12
175014-1040#10 Flat Washer:4s

175014-1050 #1/4Flat Washer.

176038-4412#1/4-20 x 3/4-Inch-long Tamper-4

Proof Flush-Countersunk-Cap Screw

177010-240 — #10-24 Hex. Polymer Locknut®34
177010-244—-#1/4-20 HiPolymer | Locknut12
178032002#10-24 Wire& Cable Tie“1

178126-002 5/32" Tamper-Proof Hex. Key Driver - 1

178265-001Nylon L-Style Standoffyee4
178297-001Red Square BOOS: Buon wath rcp2
A043825-02Foot Pedal. “Assembly1
A046501-01| JAMMA Harness’ Assembly©...1
A047492-01‘XY Steering Control Assembly°°1
A047955-01Hydra Board Set. Consists of:roe |
A047896-01| Hydra Game PCB Assembly1
A047184-03JSA Audio Il PCB 3 Assembly _1
177000-536#6-32 Nylon Nut’!23

178278-616 . #6 Threaded PCB Standoff . & 3

A047964-01Interconnect Control Harness1

TM-354 Hydra Universal Kit 3:2 Installation Instructions : 1 ” Packaging materials are not. listed) e ee :

Page 9

Hydra Universal Kit

Inspecting the Kit

Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Hydra kit serial number, part number and description of the missing or damaged parts, and date received.

Preparing the Cabinet for

the Kit Installation

  • Turn off power to the game. 2, Remove the following from the cabinet: m Old PCB(s). m Game harness, if it is not Japan Amusement Machinery Manufacturers Association ((AMMA)compatible. @ Control panel decals, labels, and controls. ws Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals. m Video display shield, display bezel, attraction shield, and marquee.
  • Wipe down and vacuum the cabinet. Paint the cabinet, if required.

Assembling the Control

Panel

WARNING The pod for the X-Y steering control must be installed so that its front edge is at the start of the control panel curve, Players could be injured if the pod is installed too far to the rear (i.e., too close to the monitor). Carefully follow the markings on the template printed near the end of this chapter.

To assemble the control panel, you need a copy of the control panel installation template (printed near the end of this chapter) and the following parts from the kit: m= Clear cover for the control panel Control pane! decal Two snap-action switches Two “BOOST” buttons One X-¥ steering control Four #10-24 x 1-inch-long carriage bolts, flat wash- Installation

ers, and locknuts m Four #1/4-20 x 1-inch-long carriage bolts, fender washers, and locknuts

  • Measure your control panel to find out what size the decal and cover should be. Cut the control panel decal and cover to fit.
  • Clamp the control panel cover to the control panel.
  • Drill four corner holes through the control panel and the control panel cover. Use a 1/4-inch drill bit.
  • Install four carriage bolts and locknuts through the holes to hold the cover and the control panel together.
  • Cut the holes in the cover and panel using a 1 3/16-inch hole cutter for the button holes, a 1/8inch hole cutter for the button tabs, and a 1 3/4inch hole cutter for the X-Y steering control connector. Use a 5/16-inch drill bit to drill the mounting holes for the X-Y control bracket.
WARNING Wear safety glasses when drilling the plastic control pane! cover. Use care to avoid shattering or chipping the plastic.
  • Disassemble the control panel and the control panel cover.
  • Install the control panel decal on the control panel. Use a sharp knife and cut out the holes for the controls in the decal.
  • Install the cover on the control panel with four carriage bolts, washers, and locknuts. 9, Install the buttons and X-Y steering control. (See Figure 1-1.)

Installing the Foot Pedal

To install the foot pedal, you need a copy of the foot pedal installation template (printed at the end of this chapter) and the following parts from the kit: m One foot pedal assembly m Four fender washers and locknuts

  • Tape the foot pedal template to the lower right corner on the front of the game. Make sure the template is placed correctly as per the measurements printed on it.
  • Drill four 5/16-inch corner holes and a 1 3/16-inch center hole through the template.
  • Feed the pedal harness through the large, 1 3/16inch center hole. Insert the foot pedal’s threaded studs into the four small corner holes.

1-3

Page 10

Installation

4, From the inside of the cabinet, install the four fender washers and locknuts onto the threaded studs of the pedal. Plug in the pedal harness connector.

Connecting the JAMMA

Harness

  • If your game does not already have a JAMMA harness, install the JAMMA harness in the cabinet.
  • Install the split beads on the harness as close to the Hydra Universal Kit

PCB edge connector as possible. Hold the beads on the harness with the tie wraps included in the kit.

CAUTION You must install the split beads included in the kit on the JAMMA harness to meet FCC requirements.

. Using Table 1-3, JAMMA Pin and Wire Connections, for wiring information, connect the JAMMA

Table 1-3 JAMMA Pin and Wire Connections

“Connect to the +12V ‘terminal of the power “Tf your coin counterts)

i ‘Attach to. the Video display.

i ‘Attach to. the Video display ‘Attach to ‘the video cane

Use this wire if you Want'an eicinal self. it test Switch on the PCB.’ (f-you connect an external sel} the PCB. Connect the wire to the N.O. terminal on th ‘common terminal of the switch to a BK/W. wire. (GND.

Page 11

Hydra Universal Kit Installation

Table 1-3 JAMMA Wire Connections, Continued

Connect one of e BKAW win at pin

the power supply’ (if it’exists) and one’ Connect two of these wir corn

‘onimion terminals of the

Page 12

Installation Hydra Universal Kit

{tems Not Shown: ‘A047964-01 Control interconnect Hames Assy 038158-01 Product 1D. Label 39450-01 FCC Compliance Label 178126-002 ‘5/92 Tamper-Procl Hex Key Driver 047206-01 178032-002 ‘traction Shield #10-24 Wire & Cable Tle Tw-354 047892-01 047889-01 Hydra Universal Kit —Bezal_ ee) Installation Instructions Display 047853-01 Shield Control Mounting Bracket 75-0702 #114 Fender Washer il 5) 75-5208 44-20 x 1 1/4" Carriage Bott (4 places) 17010244 4#1/4-20 Polymer Hex Locknut \ (4 places) \

}047691-01 a Side Panel Decal \ \ (2 places)

‘A047955-01 . Hydra Board Set (See Figures 4-4 & 4-5) 18047492-01 - 178265-001 XY Steering Control Assy L-Siyle Nylon Standotts 17014-1050 (4 places) 1/4 Flat Washer 7266128 -(4 places) ) #6 x 9/4" Pan-HD Screw ‘176038-4412 @ (4 places) {#114-20 Countersink Screw (4 places) is ee

; — “oune ——SeltTast . Contra! ‘Switch

75-5128 #024 xa" Carriage Bolt (4 places)

175014-1040 |_| Fiat Washer (4 places) 17010-2400 #10-24 Polymer Hex Locknut (4 places) A049825-02 Foot Pedal Assy 178297-001 177010-244 ‘Sq, Red Bution Assy #1/4-20 Hex Polymer Locknut (places) (4 places) oera09-at 160044-001 ‘78-0700 Control Panel Cover ‘Snap-Action Switch 4/4 Fender Washer (places) (4 places) Control panel in closed position

Figure 1-1 Hydra Kit Parts Installed in Cabinet

Page 13

Hydra Universal Kit

harness to existing component harnesses, Use crimp splices or butt soldering.

WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Hydra kit requires +5V and +12V. If -5V is available, it should be used too. Tie off any other voltage wires on the power supply besides +5V, -5V, and +12V. There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that the edge connector does not overload and burn.

Connecting Video Display Wires

NOTE The JAMMA harness provides only negative composite sync. If your video display requires separate positive sync, see Chapter 3 for alternative wiring.

Connect the wires designated for the red, green and blue video guns along with the syne and ground wires, according to Table 1-3. Connecting Coin Door Wires

  • Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.
  • Connect one terminal of the door lamps to one of the BK/W wires. Connect the other terminal of the door lamps to the R wire supplying +5V. Installation
NOTE Do not use -5V for the coin door lamps. -5V is required for audio.

(Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.) Connecting the Control Wires Connect the joystick harnesses and the button harnesses to the JAMMA harness according to the information in Table 1-3.

Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.

WARNING For the safety of players, you must connect the green ground wire as indicated above.

Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and -5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Installing the Hydra Game

PCB

  • After you have checked the power on the JAMMA connector, above, install the Hydra game board set in the cabinet. Use the nylon standoffs and four #6- 32 screws in the kit.
Page 14

Installation

  • Connect the JAMMA connector to the PCB.
  • Secure the JAMMA harmess away from the PCB with cable ties.
  • Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 3.

Installing the Bezel, Labels,

Decals, and Attraction

Assembly

The kit parts are shown assembled in a cabinet in Figure 1-1.

Installing the Display Bezel Find the cardboard display bezel (part no. 047892-01). This bezel can accommodate both 19-inch and 25-inch video displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required, Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC label (part no. 039450-01) on the back of the cabinet.

Installing the Side Panel Decals Find the side panel decals. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1-1. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry. Installing the Attraction Assembly Find the Hydra attraction shield and the attraction film. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-1.

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 for information about the option settings.

Game Play

This section of the manual describes the theme of the Hydra game and the game play features. Introduction You are the HYDRA, a courier for hire. You are a highlypaid specialist who delivers cargo to remote locations across the globe, World powers seek you out for dangerous assignments that only you can accomplish. Your toughest competitor, The Shadow, is always on your tail

1-8 Hydra Universal Kit

waiting to pick up cargo that you lose. You pilot the “Hydracraft,” a customized boat which can boost itself into the air. Your goal is to remain the top-paid courier in the world and live long enough to earn sufficient money to retire in luxury.

Hydra controls consist of an accelerator pedal, boost buttons to launch the Hydracraft into the air, and Atari’s custom flight controller. On the flight control, the left thumb button is used to select a special weapon from the player's arsenal, the right thumb button activates the special weapon, and the trigger buttons fire the laser cannons. The handles contro! the altitude of the Hydracraft while in flight. The player can start on novice (mission one), intermediate (mission three) or advanced (mission five). Extra fuel, weapons and points are awarded for starting at a higher level. There are a total of nine different missions for the player to compiete; each mission has a number of sectors depending upon the level of difficulty. The player must avoid and shoot enemy patrols while picking up fuel and boost crystals along the way. The missions take the player all over the world to exotic places like Baja California, the North Sea, Cuba, Casablanca, Central China, Libya, and more. The player must deliver nine different top-secret cargos while combating the enemy. The player is “paid” to deliver a mutant virus, the recovered crown jewels, a nuclear device, a spy satellite, laser rifles, a space station, mutant killer bees, a mad scientist, and a doomsday device. Enemy forces include zeppelins, helicopters, mines, patrol boats, hydrofoils, Hovercrafts, armored boats, jet fighters, and half-tracks, among many others. Between missions, the player enters the Hydradome bonus round. In this wave of game play, the player drives through fuel gates and over jump ramps and through rings of fire to collect cash balloons while landing on targets for bonus. Cash eamed during game and bonus waves can be used to purchase special weapons. In the last mission, the player must dispose of a doomsday device before it explodes and destroys the world. There is an extravagant end-of-game sequence when the Hydra deposits the bomb into an active volcano where it explodes, Hydra then comes fact-to-face with his arch rival, the Shadow. If the player completes the last mission, the identity of the Shadow is revealed. The player can buy special weapons with cash earned and money bags collected during game play or by adding coins to the cash box. Special weapons include the uzi, six-way shield, nuke, flamer, anti-gravity, homer, and bombs. Players can also purchase additional fuel in Ziggy’s weapons shoppe.

Page 15

Hydra Universal Kit Installation

Install this boost button (one of two) in the upper left and upper right corners of the control panel, as shown in Figure 1-1.

BOOST BUTTON

X-Y Steering Control -+-

WARNING The pod for the X-Y steering control must be installed so that its front edge is at the start of the control panel curve, Players could be injured if the pod is installed too far to the rear (i.e., too close to the monitor).

Downward curve of control ALL. LTILILILL AL LLL LLL LLL. CL panel (closest to player).

X-Y STEERING CONTROL

Page 16

Installation

N Hydra Universal Kit

S

Page 17

© O—

FOOT PEDAL HOLE PATTERN |

Page 18

Installation

N Hydra Universal Kit

S

Page 19

CHAPTER 2

elf-Test

Use the Hydra

self-test to check

the condition of

the game circuitry and controls. You will see

the self-test information on the video display

and hear the sound test information through the speakers. You do not need any additional

equipment to perform the self-test. Perform

the self-test when you first set up the game, each time you

collect the mon-

ey, or when you

suspect game problems. This chapter shows the screens in the self-test and explains each

of the tests. The screens and explanations are arranged in the order they appear in the self-

test. Table 2-3 lists all the self-test screens and

their purposes.

Page 20

Self-Test

RAM and ROM Test

‘When you turn on the power, the game automatically runs through the random-access memory (RAM) and read-only memory (ROM) test. This test is not part of the self-test procedure. Regardless of whether or not the game has a problem, it will always advance to the attract mode, The game will stop only if you power it up and the self-test switch has been previously turned on.

Game RAM Test No message appears while the test is checking the RAMs (this takes about half a minute). If more than 30 seconds elapse and the self-test menu doesn’t appear, the game has a problem. See Table 2-1 for the locations of bad RAMs. If the test finds no RAM errors, no message appears and the program goes to the ROM test after four seconds.

Game ROM Test If the test finds no ROM errors, no message appears and the program goes to the title screen in the attract mode. If a ROM fails, a message is displayed. Furthermore, if the failed ROM is a program ROM, then the error number with checksums is shown in the center of the screen. The ROM error test takes a few seconds. See Table 2-2 for the location of bad ROMs. If you think you have a ROM error, but the screen shows no messages, see Table 3-3 for information about the locations of various ROM functions. Depending on how bad the ROM error is, you may not be abie to enter the self-test.

Entering and Exiting the

To enter the self-test, turn on the self-test switch on the JSA Audio II PCB (next to the volume control). Do-

Table 2-1 Bad RAM Location by Error Address Hydra Universal Kit

Table:2-3 Summary of the Self-Test Screens

ing so displays the select test menu (entitled “Self Test”); see Figure 2-1. Exit the self-test by turning off the self-test switch at any time.

Select Test Menu

Choose which test or screen you want to see from this menu, shown in Figure 2-1. Move up and down the menu using the left or right trigger button. Start the selected test by pressing either boost button.

_ Error Address _ FE8000'(Colof RAM)“ FFO000 (Video RAM)

2-2 Figure 2-1 Select Test Menu Screen

Page 21

Hydra Universal Kit

eae Statistics Use the information shown on the statistics screen (see Figure 2-2) to keep track of your game use and maximize your profits. Record the information on the Hydra statistics page in the back of this manual. The statistics are collected from the last time the statistics were cleared. You can clear the statistics by pressing the trigger and thumb buttons all at once. The statistics are as follows: = Left Coins shows the number of coins counted in the left coin mechanism. m_ Right Coins shows the number of coins counted in the right coin mechanism. m New Games shows the number of unique games played. A unique game is counted every time a player starts a new game (not a continued game). = Continuation shows the number of games that players continued. m Free Games shows the number of free games played. This statistic can help operators detect and monitor excess use of free games. m Novice is the number of games started at the “easy” level. m_ Intermediate is the number of games started at the “medium” level. m= Advanced is the number of games started at the “hard” level. m= Idle Time is the number of minutes the game was idle or not being played. m Active Time is the number of minutes the game was played by anyone. m= Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 30E on the Hydra game PCB. m Total Credits is the number of credits accumulated by the game. m= Bought Coins is the number of coins used to “buy” weapons in the shop. m Total Coins is the total number of coins registered by the game. m Average Time per Credit is displayed in seconds. m Average Time per Coin is also displayed in seconds. Press either boost button to leave this screen and go to the histograms. The seven histograms (bar graphs) are as follows: m Histogram 1—Level died at 1A-GD shows how Self-Test

Figure 2-2 Statistics Screen

many players “died” at any of the levels from 1A to

m Histogram 2—Level died at 7A-9F shows how many players “died” at any of the levels from 7A to 9F. In addition, the end of this histogram has the line “FIN” for the number of players who finished the game. = Histogram 3—Level continued from 1A-6D shows how many players continued a game from the levels 1A to 6D. m Histogram 4—Level continued from 7A-9F shows how many players continued a game from the levels 7A to 9F. m= Histogram 5—New game times shows how many seconds all new games lasted. m= Histogram 6—Continued game times shows how many seconds all continued games lasted. m_ Hisiogram 7—Weapons bought shows how many of each “weapon” players purchased in the game. Press either boost button to leave this screen and go to the select test menu.

Coin Options

Check and select the coin options on this screen, shown in Figure 2-3. The screen shows the factory default settings in green. To move through the options, to change or save the settings, Or to return to the select test menu, follow the instructions shown at the bottom of the screen. The

Page 22

Self-Test

coin option settings, with defaults, are shown and explained in Table 2-4.

Game Options

Check and select the game options on this screen, shown in Figure 2-4. The screen shows the factory default settings in green. To move through the options, to change or save the settings, or to retum to the select test menu, follow the instructions shown at the bottom of the screen. Hydra Universal Kit

Figure 2-4 Game Options Screen

NOTE Press the right trigger button to scroll down through the options, and the left trigger button to scrol/ up.

Figure 2-3 Coin Options Screen The game options, with defaults, are shown and explained in Table 2-5.

Alphanumeric Test

The alphanumeric test, shown in Figure 2-5, checks the condition of the alphanumerics in the game. If you

Table 2-4 Coin Option Settings

credit counts as 4 coins credit ‘counts as-5'coins T credit counts as 6 coins 1 credit unis as 1 coin + No bonus adder + * 2 coins give 1 extra coi “4 col give] extra coin

5 coins give 1 extra coin. “3 coins give 1 extra coin:

Free Play (for demonstration ‘mode)

2-4

Page 23

Hydra Universal Kit

Table 2-5 Game Option Settings Self-Test

“Available Settings " Rasiest,* Easier; Easy) Medium Medium Hard, id, “Harder, Hardest Yes No

Demonstration ‘only mor

Playable Game Mode

Figure 2-5 Alphanumeric Test Screen

see an error on the screen, check the EPROMs at 15L. Pressing the left and right trigger buttons pages the screen up and down; moving the control up/down scrolls up and down. Press either boost button to go to the menu screen.

Motion Object Test

The motion object test screen, shown in Figure 2-6, tests the movement and color of various game objects. Choose an object and move it or change it as follows: While holding down this button: — This action results: Left trigger Left/right and up/down steering moves the object around on the screen, Right trigger Up/down steering enlarges/shrinks the object. Right trigger Left/right steering changes the screen to another object. Left & right thumb Select one of the three objects to be manipulated. Using these controls, you can display all 700 pictures used in the game. Press either boost button to go to the select test menu.

MOB TEST

Figure 2-6 Motion Object Test Screen

Switch Test

The switch test screen is shown in Figure 2-7. Test the coin mechanisms, boost buttons, and switches in the X-Y steering control. As you use each control, white highlighting appears around its name on the screen. If the highlighting does not appear, check the connections, switches, and coin mechanisms. To reset the limits of the X-Y control and foot pedal, press both thumb buttons simultaneously. Turn the X-Y control to the right, left, up, and down until the white numbers next to the green ones stabilize (stop changing) after each action. Also press the foot pedal and hold it until the number stops changing. Press the two trigger buttons simultaneously to return to the menu screen.

Page 24

Self-Test

P/DOWN

Figure 2-7 Switch Test Screen

Figure 2-8 Playfield Test Screen

Playfield Test

The playfield test screen, shown in Figure 2-8, tests the movement of the playfield. Turn the X-Y steering control up, down, left, and right to check whether the whole picture moves accordingly. Press either boost button to go to the menu screen.

Color RAM Test

This test has seven screens, the first of which is shown in Figure 2-9. Advance to each screen by pressing either trigger button. m The first color bar test indicates the dynamic range of the video display color circuit. The screen should show four bands (red, green, blue, and white, from top to bottom), ranging from dark to bright, left to right. The red, green, and blue bands are produced by only one color gun being turned on in each band.

2-6 Hydra Universal Kit

Figure 2-9 Color RAM Test Screen.

m The second color bar test shows the same as the first test, but with two color guns being turned on in three bands—a yellow band (red and green guns), cyan band (blue and green guns), and magenta band (blue and red guns). At the bottom is a white band, in which all three color guns are turned on. m The remaining five screens are color purity tests. The rectangles of color shown are red, green, blue, white, and grey. Each screen should display a straight rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. If any of these screens are not correct, adjust the video display as described in the video display manual. Return to the menu screen by pressing either boost button.

Convergence Test

The convergence test has five screens—black, violet, green, blue, and grey. The black screen is shown in Figure 2-10. To see the remaining screens, press either trigger button. Press either boost button to go to the menu screen, Check the following on the screens: m The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel. m The convergence of the lines on the violet and black screens should be within 2.0 mm. If these screens do not meet these criteria, adjust the video display as described in the video display manual.

Page 25

Hydra Universal Kit

EL sR EA TT AWE Figure 2-10 Convergence Test Screen

Sound Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-11. Use the right or left trigger to select from the 199 sounds; press the right thumb button to listen to it and the left thumb button to stop it. (You can have numerous sounds playing simultaneously, or you can have Self-Test

Figure 2-11 Sound Test Screen

silence, depending on which ones you select.) To select the sounds beyond number 130, watch the display in the middle of the screen, and keep pressing the right trigger button. The sound number will increment up to 233 and then start over with 1. Pressing either boost button returns you to the menu screen.

Page 26

Self-Test Hydra Universal Kit

N O T E S

2-8

Page 27

CHAPTER 3

~ Troubleshooting

and Maintenance

This chapter contains trou-

bleshooting tables and re-

pair procedures for your Hydra™ game. The chapter

troubleshooting tables. The first ta has two parts. The first part contains three

ble has

general troubleshooting information, the second table contains the voltage levels and test points on the game printed-circuit board, and the last table describes oe | ROM-caused problems with Het specific ROMs to check and

replace. The last part of the chapter has information about connecting the video display if it requires separate positive sync, repair information for the X-Y steering

control and foot pedal assembly, and locations

of the RAMs and ROMs on the game PCB.

Page 28

‘Troubleshooting and Maintenance

Table 3-1 Troubleshooting Table Hydra Universal Kit

"Figure 2 1) for ROM locations. X-Y Steering Control Problem, 1, Have the conirols been h ibricat Pedal Problem. : “them as shown’ in Figures “4-2 and 4-3. wie 2. Check the harnesses and connectors. ;, Check the’ switches on the control.

+ Is the’game plugged Is the game turned on?.

Is the line’ fuse good? Ate the solder connections on the line filter and ./ Is the JAMMA connector on the PCB tightly cont

‘or 110 VAC, depending on the type of video display

(0. If the level is not correct, ct

  • You probably have 2 serious acl RAM: Display area ‘wavers or i is too small.” ee _Do you have'high voltage to'the video displ

Picture is wavy. ‘1, Is the monitor ground connected to the moni Lor?

z 2. Are the’sync inputs connected properly? Does

Picture is. upside do Convergence, purity or color problems. Picture is not centered.

. Is the voltage level to the video display PCB correct?

3-2

Page 29

Hydra Universal Kit ‘Troubleshooting and Maintenance

Table 3- 2 Voltage Inputs ae ‘Test Points on the PCB

Video Display Sync

Problems

Some video displays cannot use the composite negative syne that is on the JAMMA connector. The Hydra kit includes a standard Atari Games video connector (ocated at 12A) that provides separate positive sync. Refer to Table 3-4 and make the appropriate connections for your video display. For other problems, see the video display manual that came with your game.

X-Y Steering Control

The steering control is shown in Figure 4-2. If you want to repair the X-Y steering control, disassemble it by removing it from the pod on the control panel. The hardware that secures the pod and steering control is shown in Figure 1-1

Foot Pedal Assembly

The foot pedal assembly is shown in Figure 4-3. If you want to repair the foot pedal, disassemble it by removing it from the front of the game cabinet. The hardware that secures the foot pedal is shown in Figure 1-1, ROMs and RAMs

If you have think you have bad ROMs or RAMs, preform the ROM or RAM test in the self-test. If you see only a colored screen and cannot enter the self-test, see Table 3-4. If you have a ROM problem, see Table 3-3. For the location of all the ROMs and RAMs on the game PCB, see Figure 4-3.

Table 3-4 Atari Games Video

Connector Pin Assignments

3-3

Page 30

Troubleshooting and Maintenance Hydra Universal Kit

N O T E S

Page 31

CHAPTER 4

~ Parts Illustrations

This chapter provides

information you need

to order replacement

parts for your kit. Common hardware parts,

such as screws, nuts, washers, and so on, are

included in these parts illustrations. When

you order parts, give the part number, part

name, the number of this manual, and the serial number of your

game. With this infor-

mation, we can fill

your order rapidly and correctly. We hope

this will create less downtime and more profit

from your games. Atari Games Customer Ser-

vice phone numbers are listed on the inside

front cover of this manual.

Page 32

Parts Illustrations Hydra Universal Kit

Figure 4-1 Hydra Kit Parts List A048371-01 A

PartNo._ DescriptionQty.PartNo.DescriptionQty.
72-07002—«#1/4 Fender Washer817514-1050#1/4 Flat Washer4
72-66128#6 x 3/4-Inch-Long, Pan-Head,4176038-4412#1/4-20 x 3/4-Inch-Long Tamper-4

Cross-Recessed Type-AB Screw Proof Flush-Countersunk-Cap Screw

75-5112B#10-24 x 3/4-Inch-Long Black4177010-240#10-24 Hex. Polymer Locknut4
Cartiage Bolt177010-244#1/4-20 Hex. Polymer Locknut2
ealComes Hole inch-Tong Black4178032-002#10-24 Wire & Cable Tie1
178126-0025/32" Tamper-Proof Hex. Key Driver1
038158-01Product LD. Label1178265-001Nylon L-Style Standoff4
039450-01FCC Compliance Label1178297-001_Red Square “Boost” Button With Lamp2
047205-01Attion Panel Shield1
GeenCuusttant oniA043825-02Foot Pedal Assembly1
A046501-01JAMMA Harness Assembly1
047853-01Control Panel Mounting Bracket1‘4047492-01XY Steering Control Assembly1
047889-01Attraction Panel Film1A047955-01Hydra Board Set. Consists of:1
047890-01Control Panel Decal1‘A047896-01Hydra Game PCB Assembly1
047891-01Side Panel Decal2‘A047184-03_JSA Audio II PCB Assembly1
;177000-536#6-32 Nylon Nut3
047892-01_19/25-Inch Monitor Bezel1
141026-001_.50-Inch LD. Split Ferrite Bead2YIE2TE-61S#6 Threaded PCB Standoff2
160044-001Snap-Action Switch2‘404796401Interconnect Control Harness1
175014-1040#10 Flat Washer4TM-354Hydra Universal Kit

Installation Instructions (Packaging materials are not listed)

4-2

Page 33

Hydra Universal Kit Parts Illustrations

N O T E S

Page 34

Parts Illustrations Hydra Universal Kit

048301-01 ‘Thumb Switch Button (2places) 048302-01 ‘Thumb Switch Housing 2, : iC noes) Left Handle Cover Pasneg Hing (2 places)

Detail of thumb switch Assembly -78207 2-56 x 7/16 Soc-HD Screw (2 places) 178248-001 Trigger (2 places)

Tube Weldment

178249-104 Right Hand Handle

040473-01 Wire Jumper| (2 places) 82-8006 10-32 x 9/8 Button-Hd ‘Tamperproof Screw (8 places)

178249-103 Right Handle Cover 1106007. Loctite 242 Blue Adhesive

Figure 4-2 X-Y Steering Control Assembly A047492-01 A

Page 35

Hydra Universal Kit Parts Ilustratrations

+176039-9607

NOTE: Harness Assy A047491-01 7 6-32x7 116 Bution Hd Tamper-Proot Screw| not shown for clari nota

A 107027-901 Lubvicant 4 178027001 Luticant es2x138 Soc-Hd Screw | (2 places)

047488-01 ‘Shaft Torsion Spring j

0s7457-01 | Spting Catch | places) | ‘70181-7606 i 46 Steel Spacer I (4places)| 19006-1001 5K Potenometer | ' I i i i I i I i Oe.

176039-3606 170007006; s77010-241 6-32. 1/4 Buton-Hd Screw 4 doco (2places) Grommet (places) 75014-1025 B12 Flat Wesher Lapa 10 Fiat Washer (2places) 047481-01 Frame Weldment

047480-01 oaozet-o1 ‘Upper Spring Centering Plate ‘ \ . Bearing Spacer +106007-003 7 Locite 242 Blue Adhesive 1175002-001 750 Washer 17008-005 762 Fiat Washer (As required) 178012-001 Retaining Ring

85-1804 #8-92x 14 Flat Hd Sorew

Pot Brackot 175014-1025 12 Flat We

‘312 FlatWasher0010

(2

;i eon10-82 x 518 Soc-Hd Screw
o67a77-01sesseecow

047490-01 Pin Lever 62x 1/4 ButHd Scrow Handle Tube Sloove @pleces) 106007-003 175005-005 1175002-004

72 Flat Washer047475.01#10 Flat Washertt
(As required)Contaring Plate(2 places)Pott
178012-0011108007-00317010-2841
-750 Retaining RingLoctite 242 Blue Adhesive10-32 Locknut

places) (places) (#8 Hex Nut

Figure 4-2 X-Y Steering Control Assembly, continued A047492-01 A

Page 36

Parts Iustrations Hydra Universal Kit

f 107027-001 Lithium Grease Le

| 72-8608 48-32 x 1/2" Soc-Hd Screw 759188 ® +#8-82 Hex Nut 19-9026 5K Potentiometer

NOTE: Lubricate on the inside of the four bearings.

4#8 Split Lock Washer (2 places) 72-1806F #8-32 x 3/8" Pan-Hd Screw (2 places)

Figure 4-3 Foot Pedal Assembly A043825-01 C

4-6

Page 37

Figure 4-4 Hydra Game PCB Assembly A047896-01 A 20306 2nay04.

Freed mot feos a ori: AS ay $4318 4 aH ea Saves mre SFiS

14F: TE3 a7 ce BES ag ME) PALS ES aye 209 ee pL Ome]

mers nn rte pe | ee) ae ees

TR ews pose oO coon “to syst oily oxi ot a) = =

EA) ASIST 0

S379 tant TE175 OF

ef) 0S =] Aloe] £0)

  • oe SOL 8

fea om mall al TT veo, OTE OSE BD

sce we ws 25 ore) Dr» We as

rpre Sehr] 5 ; = = (8. masse Te

raFa9 rasens i OE a

eae = = ile “we oa : id it = ws psa a be iE 186359 soe egos

zr1s3 al OSB: ee rusian =] maus377 lg oe a ae = ge mel oe

ff ih Wi is jeer, SO gate ms en

cut swreus rauszus. Oe ese) EOS sa Tass Tse

oo 102

ae = rasay ey eT ost rw t=] El, oa b 7 = uray 79F363 7563 amuse sore) Ee | ge] ba OD » —& OUTE z 2 CATAAT CANES © 84 WAGE IN USA a) i i i Hydra Universal Kit Parts Ilustratrations

Page 38

Hydra Universal Kit Parts Illustrations

Ls393 OL =I)

RSO 2S) OL AL aw as gee

Ls74 © siaz L$138 st fami a pte Ls24o

Ls273 SR jail] BEESREE|

80)_= 10 137579-001 oa Re 2 s37526-001 136056: 2104

Lsi74 oa

aS Te, 40665 ule oe tes a: og el} —— te lank

NOTES: 1, THE FOLLOWING COMPONENTS ARE NOT STUFFED Re? R41, RSS 2 RIS, RI6,| RAR. C1,C6,C7,044 C46, C62. 1X1,03. a.

BOD JUMPER BETHEEN 6B PIN 5 AND 6B PIN 10.

  • MODIFICATIONS TO ASSEMBLIES USING O4G488-01 REV A PC BOARDS:

‘igure 4-5 JSA Audio II PCB Assembly E A047184-03 A

4-8

Page 39

CHAPTER 5

Schematic Diagrams

This chapter con- are printed at tains the schemat- the end of this

ics diagrams for chapter. (The your Hydra™ game PCB and the JSA Audio II two board assembly drawings are illustrated PCB. In addition, the faulty RAM/ROM tables in Chapter 4, Parts Illustrations.)

Page 40

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 41

Hydra Universal Kit Schematic Diagrams

#59 seuptRa 3 23 ss 1 3 aud-24 68.0132 on 68.093-fo susrb2 /AUDBUSY secs fos Taga aun-27 we PoP op Pp sco LETEST. au0- as1 gaios gre SRes /SELETES uo-29 F491 FRLOS BRIG SRS Ls 008 Loge Long Lona Lone Ra ° AuD-23 a0 25 as 144g >s AuD-25, 68. /UNLOCK Fos 479 .00P 68./WL eS

xELT R69 $A70 $272 $3282 ak fa70 fa75 dt-1-— 4 ee reed $8.3 a 520 fs 238 PUNCH a 285: PRe. ut-6 az E3353 erry 8 & sper 38-82 ar i P5858 a B23 at-2 an

Figure 5-1 Hydra Game PCB Assembly Schematic Diagram 045977-01 A

Page 42

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 43

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 44

Schematic Diagrams

font a R59 34 we 5306

R99 XE 10K "44.318 S00

e273 [a]

R52 ak Hydra Universal Kit

REDS sem-12

vID-4

Re. 08S. 100) a + 29 vin-2

VIO 3 KEY

a2 '2n3908

B50 Sree | GREEN yg ma 2 3823 030 #00 rooP pe Moe, vIo-5 GREENS Joyy

Page 45

Hydra Universal Kit Schematic Diagrams

een SESE SERRE» AUD-16 SPKR2-5 yp. Wes Se Ps AUD- 18

waeR25puo

SAM-H— KEY Se JAN? — KEY os AM eer’ RUD-1 JAM oS au-2

apne 11 EOBUD, auD-19$2%5 auo-22

72 25 auo-39 JbaP 845 pup-40 wAN-D0-—

PHO er.SPRPINS825 eun-3
wem-20"wOsieBX pup-4

CONTRE CONTR

JRO CONTRtconteg? WO“NOS u-7
JAMS——CENTRES, gun-12BS aup-8
ate SEEN{i.ESINLS ayp-36NS:
167 Cone.rifcom7ESS; pu-13
SABLeSETiLtrireeniiedFuD-14
san7T;++To aiaAuo-22
JAMS;*25 Au0-5BAG pup-24
vere1—+S Fd 6MD, auo-26
j|||i24445 aup-37S05 UD-28
iiiRaaBAC
PMR:> AUD~31AuD-30
i|i|]BS pup-34
AMS:-t-AuD-23 GNo-#NSs aup-38

Lca2 Less Lees 2023 | ese cs

LiTTTi

22+ ++

Figure 5-1 Hydra Game PCB Assembly Schematic Diagram 045977-01 A

Page 46

Schematic Diagrams Hydra Universal Kit

PR

Ji-4 Ji-10 ae J4-32 J4-34 Ja-40 Red Ji-24 gk : J1-26 a Ja-3 €2,8,9,22,23, ui-34 sid 30,47, 63-67 . J1-38 vi-7 wt J1-8 ui-a3 cBYPASS?

5-8

Page 47

Hydra Universal Kit

*12V Schematic Diagrams

Cot ceo i—___+#___5 1-15 470/25Y 470/25V

J1-22,

Ji-16

SELF-TEST

JNM

SFULL

Ls240

/RDIO: > DD DD DD Yi so7 Y3— spe yf sos

yA— soy

yH2_ S03 4 sn2

sos

Figure 5-2 JSA Audio II PCB Assembly Schematic Diagram 046487-01 E

3-9

Page 48

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 49

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 50

Schematic Diagrams Hydra Universal Kit

| Daas 10K

i oAo 3300PF RSS 3.3K

+5 sui

SELF-TEST OF ote R20 if 10K OND po ag =cno $07 —*%} = /SNORES Raz

Ji-24

J1-25,

5-12

Page 51

Hydra Universal Kit Schematic Diagrams

YAMAUD

Figure 5-2 JSA Audio Il PCB Assembly Schematic Diagram 046487-01

5-13

Page 52

Schematic Diagrams Hydra Universal Kit

Bad RAM Location by Error Address

Figure 5-3 Faulty RAM/ROM Tables

5-14

Page 53

° > =

Statistics Screen

Left Coins:

Right Coins: New Games:

Continued Games:

Free Games:

Novice:

Intermediate:

Advanced:

Idle Time:

Active Time:

Error Count:

Total Credits:

Bought Coins: Total Coins:

Avg. Time/Credit: ML TET

Avg. Time/Coin: sec, sec. 1A

1B

2B

2c

3A

3B

4a

4B

4C

5A

5B

5c

6A

6B

6D

Histogram Screens

Histogram 1: Level died at (1A-6D)

TA

7B

7c

7D

8B

8D

9A

9B

9C

9D

9E

OF

FIN Histogram 2: Level died at (7a-9F) Histogram 3: Level continued from (1A-6D)

1A

1B

2A

2B

2c

3A —

3B

3C

4A

4B

4c

5A

5B

5C

6A

6B

6C

6D

See over for Histograms 4-7

Page 54

Histogram Screens

Histogram 4:Histogram 5:Histogram 6:Histogram 7:
Level continued from. New game timesContinued gameWeapons bought
(7A-9F)(seconds)times (seconds)
7A__0-290-29 ___Uz ___
7B—_30-5930-59 ___OWAY _
7c—60-89 __60-89 ___SHIELD ____
7D__90-119 __90-119 ___NUKE ____
8A__120-149 ___120-149 __FLAME ____
8B__150-179 ____150-179 __AGRAV ____
8c—__180-209 ____180-209 ___HOMER ____
8D_210-239 ___210-239 __BOMBS ____
9A__240-269 __240-269 ___SPARE ____
9B—270-299 __270-299 __SPARE ____
9c—300-329300-329 __SPARE _____
9D_—_330-359 ___330-359 __SPARE ____
9E—360-389 __360-389 __SPARE ____
OF—390-419 ____390-419 __FUEL ____
420-449 __420-449 __SPARE _____
450-479 __450-479 ___COIN ___

480-509 480-509 __ 510-539 510-539 __ 540-569 540-569 570&UP 570&UP

Page 55

peel pel pede fed pel ped pel feed pepe fel ped pele pele pele pele ele peeled fel el pel el fell

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller's plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

PEE eee eee eee lela elelel eel

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the qu: of any non-Atari part or any modification including labor which is eatorined by such distributor.

Page 56

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.