CATHODE RAY TOMES

Up Scope

Up Scope (Grand Products, 1986) · Document · 25 pages · 17 sections · original scan

Page 1

GAME NO. #103-000 FEBRUARY 1987

UP SCOPE INSTALLATION

&

INSTRUCTION MANUAL

GRAND PRODUCTS, INC.

775 Nicholas Blvd. - Elk Grove Village, IL 60007

(312) 593-2770

Page 2

A GRAND New Winner

Video Submarine Mission

To Sink The Enemy Fleet!

UP SCOPE...dedicated to UP PROFITS!

Players take command to destroy enemy ships along the horizon on a rolling screen. It’s an exciting battle against time and obstacles, U-Boat skippers sight targets through scope using firing handles to raise, dive and maneuver the sub in 180° swing. Aim ire torpedoes! Direct bits send blazing ships to the bottom of the sea. ‘Top row targets score higher points. Voice alarm warns of sub chaser attack. Dive...but watch out for mines and depth charges. Destroy sub chaser for extra bonus points. Extended play and bonus time adjustable. If player's sub is hit, it sinks, explodes and releases an oil slick. The Grand UP SCOPE features realistic graphics and sound effects. Takes up little space with great returns in any location. Special built in pull-out siep for shorter players. Join the UP SCOPE crew tor deep sea, money making, play action opportunities. See your distributor or call us!

GRAND PRODUCTS, INC. 775 Nicholas Blvd. Elk Grove Village, IL 60007 Phone: (312) 593-2770

©1986 Grand Products, Inc.

Page 3

soe

TABLE OF CONTENTS

_ Page No.

INSTALLATION 1 GENERAL GAME OPERATION ; 2-3

GAME INSTRUCTIONS 4-6

GENERAL TROUBLE SHOOTING 7-9

GAME SELF TEST AND ADJUSTMENT 10-14

MONITOR ADJUSTMENTS 15-16 GAME I AND 0 BOARD SCHEMATIC 17

EPROM BOARD SCHEMATIC 18

PARTS LIST -¥9-20

© 1987 GRAND PRoucTS, INC.

WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

Page 4

uP scope ™

INSTALLATION

  • Adjust 4 (four) provided leg levelers on bottom

of cabinet. (Installed at factory)

  • The 117VAC power is controled by a switch

located on top of cabinet.

  • Plug line cord into 117 volt 60 cycle grounded

outlet.

VOLUME CONTROL POTS

  • Located in cash box area left side and controls

volume_of_all_sounds.—_-Sounds_maybe-varied by

rotating pot control.

GAME ADJUSTMENTS

  • Refer to self test menu for battery back up

operators settings.

REMOVING FRONT VACCUM/PERISCOPE ASSEMBLY

  • Remove all screws (10) holding front vaccum

assembly to access periscope, mirrors, speakers,

lamps and sight assembly.

Page 5

GAME OPERATION

CREDIT

1. After power up sequence coins can be deposited

and 1 player game can be played. Adding

additional coins will accumulate credits as

shown on screen.

STARTING GAME

1.

2.

3.

5. Pressing Fire button starts game.

Various ship targets move across the monitor

screen when viewed through periscope.

Game timer (adjustable) starts count down and

pressing Fire button will shoot torpedoes.

Steering periscope and hitting or sinking ships

the game will score points.

The underwater submarine will steer left and

right when moving periscope. Pressing left

handle buttons submarine will go up or down,

Press Fire button to shoot underwater missile

at sub chaser.

When a certain score is made the Bonus time

feature will add additional time. The Bonus

time feature is adjustable.

Page 6

8, The ten top high scores will be displayed on the

high score screen with player initials.

  • Good Luck
Page 7

INSTRUCTIONS AND SCORE VALUES

-* DEPOSIT COIN, .* PRESS FIRE BUTTON TO START GAME.

SURFACE SCENE

  • LOOK THAU VIEWER AND MOVE PERISCOPE RIGHT OR LEFT TO SELECT TARGETS.
  • PRESS FIRE BUTTON TO SHOOT TORPEDOES.
  • SHIPS WITH HIGHEST TARGET VALVE APPEAR IN TOP ROW.
  • SUB CHASER APPEARS AT ENEMY RIGHT LEFT COM- MAND; IF NOT SUNK, SUB- MARINE |S FORCED TO DIVE UNDERWATER,

UNDERWATER SCENE

  • MOVE SUBMARINE - RIGHT- LEFT-UP OR DOWN TO AVOID MINES AND DEPTH CHARGES.
  • POSITION SUBMARINE UNDER SUB CHASER AND FIRE TORPEDO AT READY TO FIRE COMMAND.
  • SUBMARINE RESURFACES AFTER DAMAGE IS REPORTED OR SUB CHASER IS SUNK.
  • GAME ENDS WHEN SUB- MARINE RECEIVES ADDI- TIONAL DAMAGE AND SUNK, OR GAME TIME RUNS OUT.

© 1086 GRAND PRODUCTS, INC.

4.

TARGET VALUES

TOP ROW

SUB CHASER 4500 PTS. CARRIERS — 1500 TO 6000 PTS. SUBMARINES 750 TO 3000 PTS. OTHER SHIPS 600 TO 2400 PTS.

2ND ROW

SUB CHASER 4500 PTS. SUBMARINE 750 TO 3000 PTS. OTHER SHIPS 450 TO 1800 PTS.

3RD AND 4TH ROWS

SUB CHASER 4500 PTS. ALL SHIPS 300 TO 1200 PTS.

UNDERWATER

SUB CHASER 4500 PTS.

BONUS TIME LEVELS

16,000 PTS. 35,000 PTS. 70,000 PTS. 100,000 PTS. 125,000 PTS. 190,000 PTS.

  • 1986 GRAND PRODUCTS, INC.
Page 8

TARGET VALUES AND HIT REPORT

All ships will score three values when hit except

the sub shaser which always scores 4500 points.

The lowest value is on the 18¢ hit when it is off

center. A 2nd hit will score higher and a dead center

hit sinks the ship immediately.

The score screen displays ship hit values and hit

report screen displays how many 18t, 224, and center hits

are made.

NOTE-

The sub chaser always sinks on the 18¢ hit.

TARGET VALUES

SUB CHASER 4500 PTs.

CARRIERS 100 Te 6000 PTS,

SUBMARINE 750 TO 3000 PTS.

OTHER SHIPS 300 TO 2700 PTS.

Page 9

HIGH SCORE FEATURE

The top ten scores will be displayed on the high

score screen, Top ten high scores will also display three

initials for each high score.

If the current score is greater than the ioth high score

on the high score screen the player is asked to enter his

initials next to his score.

The s€reen format will be similar to the following:

INITIALS HIGH SCORES

1BAD200 000
2ccc198 000
2FAR150 000

YES 110 000

5ADD1408 000
6WER97 000
isSAQ96 500

EAR 95 000

9PATze 000
10JAK5 000

CONGRATULATIONS YOUR SCORE WAS 108 000

ENTER YOUR INITIALS A _

TURN PERISCOPE TO CHANGE LETTER

PRESS FIRE BUTTON TO PICK A LETTER

Page 10

uP score ™

GENERAL TROUBLE _SHOOTING

INTRODUCTION

The most common problems occur in the harness area

such as the coin door, player controls, interconnect

wiring etc. The TV monitor trouble shooting will not be

covered in this manual. This information can be obtained

from Wells Gardner. (Telephone 312-252-8220)

The Logic PC board is a complex device and should be h:

handled with care.

GENERAL SUGGESTIONS

The first in trouble shooting procedure is correctly

identifying the malfunction symptoms. A careful trained

eye will see additional clues.

After all the clues are carefully considered, the

possible malfunctioning areas can be narrowed down to one

or two good suspects. Those areas can be examined until

the cause of the malfunction is discovered.

HARNESS COMPONENT TROUBLE SHOOTING

Possible problems in this area are coin, credit,

power, lights and failure of certain features.

NO COIN OR CREDIT

A coin is inserted and a game is not awarded. First

check to see if the coin is in the return cup. If the eoin

has returned the problem would be in the coin acceptor only. Next clean and inspect the coin acceptor and try with coins.

Make adjustments or replace coin acceptor. “7+

Page 11

NO CREDIT AND COINS GO INTO CASH BOX

In this case you have a coin switch failure or an

electrical failure of the coin/start circuit. First

examine the coin switch wire form, stroke and wire connecé

tions, Then check coin switch for continuity with Ohm

meter. If coin switch checks out proceed to the wiring

between coin door and logic board.

If the above checks out the trouble must be in the

coin/eredit circuits of the logic board.

TRANSFORMER AND LINE VOLTAGE

Your game must have the correct line voltage to

operate properly. No game will function below 105VAC.

In aay case the best way to check for correct tine volte

age is with your volt meter. Set the meter to the next

higher scale above 117VAC and stick your probes in the

wall outlet. If it is good here check the 117VAC trans-

former wiring, solder connections, fuse block, on/off

switeh, switch and wiring harness.

The transformer must be correctly grounded to pre-

vent a hum bar, rolling up or down the TV screen.

HARNESS PROBLEMS

Additional harness problems can be fuses blowing and

malfunctioning control.

The best way to approach this problem is by turning

the power off and disconnecting devices that may beveausing

the condition such as the monitor, PC boards and controls.

Disconnect the devices by pulling off the connectors and

Page 12

connecting your volt meter across the fuse that is blowing

(Power turned off) and set your meter to a resistance scale.

This will save blowing fuses each time you check the circuit

for a short. If the meter reads no short with all connectors

removed, re-connect the devices one at a time until the meter

reads a short. The last device connected caused the short.

If the meter reads a short with all devices disconnected then

the short is caused by the harness cabje which may be pinched

somewhere.

MALFUNCTION CONTROLS

The most common problem here would be a bad potentiometer,

switch, connector or wiring. A bad pot is normally replaced

and switches readjusted, cleaned or replaced, Check for pinched,

broken and wire soldering. Also check wiring from controls to

logic board using volt meter. If everything checks out, your

trouble is in the logic board circuits.

Page 13

SELF TEST

There are a series of diagnostic screens that allows

the logic system to be tested and aid game alignments.

To enter self test locate the red push button in the

cash box area.

Turn game off and on and hold red push button during the

entire test. The game will enter the self test mode and the

first screen will be the self test menu.

Steering the periscope will allow you to ehoose each

self test from the menu as they change color, (1 to 7)

Press the Fire button and the choosen teat will appear.

MENU

POT (CALABRATION)

BUTTONS (SWITCH TEST)

LAMPS

SOUNDS

RISET H (HIGH SCORES)

CROSS HATCH ANU Fw DY BH OPERATOR SETTINGS

When the self test red push button is released and power

is turned off and on then game will return to the play mode.

  • Por

The pot value will be displayed on the screen and

by turning the periscope the pot value will be 0 with

the periscope to the right and 225 to the left.

Page 14

SELF TEST POT nes See {y-

There are a series of disgnostic screens that allows

the logic system to be tested and aid game alignments.

To enter the self test locate the slide switch in the

Cash box area.

When in gase over mode move the self test switch to the

test position. The game will enter the self test mode and

the first screen will be the self test menu.

Steering the periscope will allow you to choose each

self test from the menu as they change cHior, (1 to 7)

Press the FIRE button and the choosen test will appear,

MENU

POT (CALABRATION) BUTTONS (SWITCH TEST)

LAMPS

SOUNDS

RESET H (HIGH SCORES)

CROSS HATCH

7 OPERATOR SETTINGS

When the self test switch is moved to the play position Nu FWD

during the menu display the game will return to the play mode,

  • POr The pot value will be displayed on the screen and

by turning the periscope the pot value will be 0 with

the periscope to the right and 225 to the left.

Page 15

A bad pot will cause the number sequence to be jumpy.

  • BUTTONS (SWITCH TEST)

The screen will display the following:

FIRE

UP

DOWN

COIN 1

COIN 2

The button or switch tested will change color on

the screen when operating properly.

Press the FIRE and UP buttons together to return

to the menu.

  • LAMPS

Move the periscope to choose one of the following

displayed on the screen.

ENEMY RIGHT

ENEMY LEFT

TORP 1

TORP 2

TORP 3

TORP 4

SIGHT

BUBBLE LIGHT

The lamp lights when choosen and the option will

change color on the monitor.

Press the FIRE button to return to the main menu.

-ll-

Page 16
  • SOUNDS,

Move the periscope to choose one of the following

displayed on the screen.

CHANNEL 1 RIGHT SPEAKER

CHANNEL 2 RIGHT SPEAKER

CHANNEL 3 LEFT SPEAKER

CHAHNEL 4 LEFT SPEAKER

The option choosen will change color.

The voice for mission over is heard continuously

every two seconds out of the choosen channel.

Press the FIRE button to return to the matin menu.

5. RESET H

The top ten high scores displayed on the high

score screen will change when they are beat.

Reset H will reset high scores back to the original

scores when FIRE button is pressed.

  • GRID DISPLAY

This test will display a cross hatch pattern used

in adjusting the color monitor. The cross hatch may be

used to adjust color, vertical linearity, convergence

and vertical-horizontal size.

Press FIRE button to return to main menu.

Page 17

Te OPERATORS SETTINGS

Move the periscope to choose one of the following

displayed on the screen,

COIN - START1/12/.3/11/2FREE
START - TIME607590105120
BONUS = TIME202530354o

The option choosen will change color and pressing

the FIRE button will lock in the choosen option.

Press the FIRE button once more and return to the

main menu,

When the self test switch 1s moved to the play

position during the menu display the game will return

to the play mode.

Page 18

5. PERISCOPE STEERING POT ALIGNMENT

Loosen periscope steering pot set screw.

Move and sight periscope to aim at the center of

the monitor and start game.

Manually turn the periscope steering pot shaft until

the compass reading on the monitor screen reads N (North)

and tighten the set screw with the periscope dead center.

Steer the periscope full left and‘ the compass should

read W (West).

Steer the periscope full right and the compass should

read E (East).

Start game and fire torpedoes at ships, check scrolling

effect.

a14-

Page 19

T.V. MONITOR

Warnings

. Power Up Warning

Caution: If the monitor is to be powered up outside of the games console, an isolation transformer must be used for the AC power source.

. X-Radiation This chassis has been designed for minimal x-radiation hazard. However, to avoid possible exposure to soft x-radiation it is IMPERATIVE that the EHT circuitry 1S NOT modified.

. High Voltage The colour monitor contains HIGH VOLTAGES derived from power supplies capable of delivering LETHAL quantities of energy. To avoid DANGER TO LIFE, do not attempt to service the chassis until all precautions necessary for working on HIGH VOLTAGE equipment have been observed.

. CRT Handling The picture tube encloses a high vacuum and due to the large surface area is subject to extreme force. Care must be taken not to bump or scratch the picture tube as this may cause the tube to implode resulting in persona! injury and property damage. Shatter-proof goggles must be worn by individuals white handling the CRT or installing it in the monitor. Do not handle the CRT by the neck. no

. To prevent fire or shock hazard DO NOT EXPOSE THIS MONITOR TO RAIN OR MOISTURE.

Page 20

COLOR MONITOR SETUP INSTRUCTIONS

GREEN DRIVE HORIZ SIZE GREEN CUT OFF RED ORIVE HORIZ_ RASTER RED. cut OFF POSITION

VERT RASTER POS VERT SIZE VERT HOLD BRIGHTNESS

HORIZONTAL FREQUENCY

With the monitor being driven with the display signal, connect one jumper between TP1 and TP2 and another jumper between TP3 and TP4. Adjust the horizontal hold control until the picture stops sliding horizontally. Remove the jumpers. Do not use the horizontal hold control for horizontal centering. (See #3)

NOTE: If the sync signal is composite, use the horizontal syne input of the same polarity as the composite sync signal.

PICTURE SIZE

Adjust the vertical size control, and the horizontal width coil for desired picture size.

PICTURE CENTERING

If the video is off center vertically, turn the vertical raster position control to move the raster up or down. If the video is off center horizontally adjust the horizontal video shift control to center the picture. If any additional horizontal positioning is required, move the horizontal raster position jumper to the left or right position.

BRIGHTNESS

Adjust the brightness control to obtain the proper illumination. Adjust this control such that the illumination is just barely extinguished from portions of the display which should be black.

CONTRAST CONTROL

Adjust the contrast control for the desired picture intensity.

Focus ’ e Adjust the focus control for the best overall definition and fine picture detail. -16-

Page 21
Scan of page 21

This page is a drawing, shown as the original scan.

Page 22

EPROM BOARD SCHEMATIC

WILL BE AVAILABLE

SOON

~18-

Page 23

I_AND 0 BOARD PC_0103-904

CHIP NUMBER

8255

8416

74LSOO

7T4LsO4

TALS 374

ADDITIONAL DEVICES

TIP 120

TDA 2003

IN 5400

BATTERY 3.6VDC

E-PROM BOARD PC 0103-701

CHIP NUMBER

TALSOO

TALS 32

TALS 123

7418138

74LS139

TALS 373

27256 FUNCTION

PARALLEL PORT (PP1)

RAM 2K xX 8

2 INPUT NAND

HEX INVERTER

FLIP-FLOP (LATCH)

FUNCTION

TRANSISTOR

POWER AMP

DIODE

41B901CD05

FUNCTION

2 INPUT NAND

4INPUT OR

MULTI-VIBRATORS

3-8 LINE DECODER

2-4 LINE DECODER

8 BIT LATCH

E-PROM 256K

Page 24

UP SCOPE TM

PARTS LIST

DESCRIPTION

Hydraulic Cylinder Volume Control Speaker 8 Ohms I and O PC Board Memory Board Mirror First Surface Lamps No# 44 Tubular Lamp 25N Power Supply Foil Paper (Periscope) Black Rubber Handle Red Push Buttons Sighting Mirror Eye Sight Mold Steering Pot (1 MEG) E-PROM PC Board Main Vac Form Inner Vac Form View Panel Glass Sight Window Glass Battery 3.6VDC PART NUMBER

0103-029-000 0054-020-000 0056-030-000 0103-700-000 0103-701-000 0103-512-000 0056-013-000 0056-027 -000 0103-010-000 0103-904-000 0042-001-000 0054-007-000 0103-511-000 ©103-505-000 0054-007-000 0052- 361-000 0103-510-000 0103-513-000 0103-503-000 0103-500-000 0052-360-000

Page 25

NOTES

This space is provided for personal notes