CATHODE RAY TOMES

Cruisn USA Linking Kit

Cruis'n USA (v4.5) (Midway, 1994) · Kit Manual · 11 pages · 6 sections · original scan

Page 1

MID WA Y January 1995

CRUIS’N USA

SIT DOWN

16-9939

INSTALLATION MANUAL FOR LINKING KIT.

COVERS BASIC (45636) & DELUXE (45736, 45836) KITS.

Midway Manufacturing Company 3401 North California Avenue Chicago, Illinois 60618

Page 2

CONVERSION PROCEDURE

Unpack materials from carton and check for obvious signs of damage. Use checklist below to be sure kit is complete.

Parts List: DELUXE BASIC KIT KIT 45636 45736 45836

PART NUMBERITEM DESCRIPTIONQTYQTY
A-19354Neon Header Assembl4
A-19993Linking Decode Pal2
A-5343-45736-1022
|__| A-5343-45736-11_|U11 EPROM22
A-5343-45736-12 | Ui2 EPROM22
A-5343-45736-13 | U13 EPROM22

H-14004 [y-Cable CT H-19492 [ACCable CT

01-13546[Marquee Mounting Bracket[|2|

01-13811-1 Header Plate, Left 01-13811-2 Header Plate, Right i

01-13858Lower Front Bracket1[ i |
16-9939Manual1[id
|__| 20-10140Tamper Proof Wrench T27i[|
|__| 20-10166-05[Tamper ProofScrewBitTi5 —s« [| =f=| Sid
20-10166-08[Tamper Proof ScrewBitT27_ |tT| SC

31-2303 [Marquee Artwork, Left sd] ST S| ST 31-2304 | Marquee Artwork, Right | OT]

|__| 4020-01100-08 | 1/4-20x 1/2" Tamper ProofScrews |6|i
4020-01178-08| 1/4-20x1/2"Hex-headBolt ss ||4S] SCs

4320-01124-32 | 1/4-20x2"”Hex-headBolt ss [| 2] 4320-01124-56 | 1/4-20x31/2”Hex-headBott [2 | SC 4420-01141-00 |__| 4700-00032-00B_|.265x.625x.067FlatWasher || —12,~=«| =i |__| 4702-00014-00B | 1/4” StarLockWasher—sd| S22 |S 4 5797-14511-00 _| Linking Cable [i [ 14 | Not all mounting hardware in this kit will be used, extra has been provided.

Recommended Tools and Supplies: Reversible Drill For Drilling and Turning Screws [| |__|HoleSaw___| 1” or 1 1/8” Diameter for Cable Holes _ | |__| SocketSet___| 7/16" Socket and 7/16” Wrench | [| T15 Torx Bit Supplied in Spare Parts Kit T27 Torx Bit Supplied in Spare Parts Kit

Page 3

SETUP INSTRUCTIONS

NOTE: To install BASIC KIT, follow starred instructions only.

*1. Turn power Off and unplug both games.

*2. Unlock and open rear doors. MARQUEE

  • MARQUEE EXTRUSION (Do Not Reinstall on Deluxe Kit) INNER CABINET SIDE BOLTS AND NUTS (4)

Y

(Pedestals removed for drawing clarity.)

*3. Remove four bolts and nuts from along cabinet top and back edges (remove only from sides to be fastened together). Remove one bolt and nut from top, outer cabinet sides (save this bolt, it will be reused to mount header assembly).

*4. Remove marquee extrusions and marquees on both cabinets. The extrusions will not be used with the neon header assembly , on Deluxe Kit only.

1/4-20 FLANGRIP NUT (4) 1/4" STAR LOCK WASHER (4)

265 X .625 X .067 FLAT WASHER Oe 1/4~20 X 2" HEX-HEAD BOLTS (2) (INSERT THROUGH BOTH CABINET SIDES)

1/4-20 X 3 1/2" HEX-HEAD BOLT (2) {INSERT THROUGH BOTH CABINET SIDES)

*5. Bolt the two cabinets together using hardware, as shown above, from the spare parts bag.

Page 4

LOWER FRONT BRACKET

*6. Install lower front bracket. Remove three tamper proof screws, star washers and flat washers from cabinet base. Screw bracket in place using the existing hardware.

ALIGN WITH TOP, FRONT EDGE OF CABINET. ALIGN WITH EXISTING HOLE al DRILL OR CUT 1" DIAMETER HOLE =—£| a ALIGN WITH EXISTING Hoe} ——+ | INSIDE CABINET EDGE

-—1r—4 TEMPUNTE

ABLE HOLE LOCATION

HEADER MOUNTING} | L BRACKET SCREWS FRONT (BO NOT DISCARD) L HEADER MOUNTING FRONT BRACKET SCREWS {DO NOT DISCARD)

IOP_VEW OF CABINETS

  • Use the drilling template to mark cable hole locations (template is the last page in this booklet). Align template with existing holes on cabinet top. Drill a series of 3/8” diameter holes around the perimeter of circle, or simply use a 1” or 1 1/8” diameter hole saw. A Jig saw may be used if care is taken avoid wire locations inside marquee areas. Flip template over to drill hole for opposing cabinet.
Page 5
  • Install neon header assembly.

_-METAL BACK PANEL

Sen, _-~ HEADER MOUNTING BRACKETS

  • Remove metal back panel from header assembly, using the T15 screw bit.
  • Install header mounting brackets using two 1/4-20 x 1/2” hex-head screws, star washers and flat washers per bracket, from spare parts bag.
  • With the T27 screw bit, remove two tamper proof screws, star washers and flat washers from outer edge of each cabinet top, this is where header mounting brackets will fasten (see “TOP VIEW OF CABINETS” above). Set screws aside, they will be reused to mount the header brackets.

The next step requires two people, it will make the job much easier.

  • Raise neon header assembly and align mounting brackets with holes in cabinets. Insert previously removed screws, star washers and flat washers, finger tight into header mounting brackets. Adjust front neon housing flush to front edge of cabinets, then tighten mounting screws.
  • Replace the two bolts previously saved from outer cabinet sides. Screw through cabinet, into side of header assembly. (see “HEADER PLATES’, following page).
Page 6

ac caBLe—\|

Y-CABLE

LEADER LAMP CABLE (ATTACHED TO HEADER) TO AC LINE / VOLTAGE CABLE

AC TO COIN ME D

SDE View SHOWING CABLE ROUTING

  • Connect both AC cables (H-19492) to connectors located at rear of header assembly. Route one each, AC and fluorescent cable, through top hole of each cabinet, then through the existing notches in back of cabinet marquee areas. NOTE: The cabinet fluorescent cables are routed through these notches, so it will be necessary to push them aside to run the connectors through.

NOTCH F (INSIDE: G MARQUEE HOUSING) CABLE ROUTE

HEADER MOUNTING BRACKETS (2)

LEADER LAMP CABLE ~J (ATTACHED TO HEADER) FF

AC CABLE

cpu | BOARD $2) Sto]

BACK VIEW SHOWING CABLE ROUTING LINKING CABLE-—————

  • Connect cables as follows: Connect leader lamp cable (orange-violet) to wheel board at location P7. Connect fluorescent AC cable (H-19492) to Y-cable (H-14004). Disconnect bill acceptor AC cable (if used). Connect Y-cable to AC line voltage cable. Connect Y-cable to bill acceptor AC cable (if used). *Connect linking cable (5797-14511-00) to either 25-pin D-connector, located under CPU board shield, on both games.
Page 7

RIGHT HEADER PLATE OUTER CABINET SIDE BOLT AND WASHER-,

LEFT HEADER PLATE

  • Check to make sure all lights work by switching On power to both games.

*i) Insert new marquee art using small plastic extrusions to retain artwork to back side of glass. Slide glass back into wood grooves. *Reinstall marquee extrusions for Basic Kit.

  • Screw left and right header plates on bottom, front of header using the T27 screw bit, six 1/4-20 x 1/2” tamper proof screws, star washers and flat washers, from the spare parts bag.
  • Reinstall rear metal panel on header assembly carefully to avoid pinching wires.
Page 8

aie a Lo Hl ea ————|

Lote t Lat

; BLU ERE eo FLeJLe] f

  • Install new EPROM's at locations U10, U11, U12, U13, and linking decode pal at location U38.
Page 9

‘dOl LANIGVO LNS0VvPdV YO4 JIOH JIEGVO ONISOddO TY Ol YSAO SLVIDWSL dild *3LON JIOH YSLaNVIC ,b LAD YO NO

Page 10

—« lic 8/1 8 SAITOH ONILSIXS HLIM NOMV wa LANISVO 40 4903 JCISNI LANIGVO 430 43903 LNOUYS ‘dOl

Page 11

January 17,1095

CRUIS’N USA LINKING KIT

MANUAL AMENDMENT

IMPORTANT INFORMATION!

DIP Switch Settings for linked games should be as follows:

Left Game (Player 1) DIP Switch 2 (U97) SW6 = ON (Link On) SW8 = ON (Master)

Right Game (Player 2) DIP Switch 2 (U97) SW6 = ON (Link On) SW8 = OFF (Slave)