Qix
Qix (Rev 2) (Taito America Corporation, 1981) · Manual · 60 pages · 19 sections · original scan
WAST © 1981 Trade Marks of Taito America Corporation Revision 1 72-00008-001

This page is a drawing, shown as the original scan.
Reproduction of this publication is forbidden without the written permission of TAITO
AMERICA CORPORATION, Elk Grove Village, Illinois. This manual is only conditionally
issued, and neither receipt nor possession thereof confers or transfers any right in, or
license to use, the subject matter of the manual or any technical information contained
thereof.
For permission requests, write: TAITO AMERICA CORPORATION 1256 Estes Avenue Elk Grove Village, Illinois 60007 Telephone (312) 981-1000 Telex 25-3290
“gix’™
TABLE OF CONTENTS
“QIX’™ GAME SET-UP ...................20-5 Page 5
1.1 Game Features ....... 2.0.0... c cence eee eee 6 1.2 Introduction ................... cee ee cece 6 1.3 Game Inspection ..............00. cece eee eee 6
1.4 Game Pre-Installation ......................04 6
1.5 Power On/Off Switch, Interlock Switches, Memory Protect Switch, Self Test Switch, Volume Control, and Service Outlet............. 7
1.6 Electronic Acceptors ........... 0.00... sence 7
1.7 Game Installation .............0. 22. ceeeeeee ee 7 1.8 Self Test Procedure ...............---- see eee 8
MAINTENANCE ..................002.. 00 eee 15
2.1 Cleaning ............ cece cece eee eee 16 2.2 Coin Door ...........6 2... eee cece 16 2.3 Fuse Replacement ....................00.085 16
2.4 Monitor Removal....................-02-285 16
2.5 Cover Glass Removal ............-..00.0000e 17
2.6 Printed Circuit Board Replacement ............. 17
2.7 Power Supply ......... 00. e cece eee eee eee 17 2.8 CMOS RAM ..........00 2.00 e eee eee 18 2.9 Test Points......... 0.06 ccs cece cence eee eens 19
THEORY OF OPERATION........................55 21
3.1 General... . 0.2... eects 22
3.2 Video Board ........... 02... cece eee eee eee 22
3.3 Data Sound Board
3.4 ROM/I/O Boatd .......... 6.0 cece cece eee 24
3.5 Software Security Module .................... 24
- ILLUSTRATION & PARTS LISTS.................... 25
Figure 1 Incandescent Panel ................-- 26
Figure 4-Way Joystick ............2ese eee 27 Figure Control Panel ............ 0.0 cece eee 28
Door Assembly ..............-..0005 30
Cabinet Assembly Upright Front View .. . .32
Cabinet Assembly Upright Rear View ... .34
Power Supply Component Layout ....... 36
Video Processor Component Layout .... . 39
Data/Sound Processor Component Layout 44
ROM/I/0 P.C. Assembly Component Layout48
Wiring Diagram ...............0...08 52
Power Supply Schematic (Fold Out)
Video Processor Schematic (Fold Out)
Data/Sound Processor Schematic (Fold Out)
ROM/I/0 Schematic (Fold Qut)
LISTS OF ILLUSTRATIONS
Figure 1-1 Programming Plug ...............000. 6
Figure 1-2 Power ON/OFF Switch ................ 7
Figure 1-3 Interlock Switches & Memory Protect Switch 7
Figure 1-4 Self Test Switches .........-......0.. 7
Figure 1-5 Volume Control Setting ..............8 7
Figure 1-6 Coin Meter
Figure 1-7 Self Test Button ........... 2.0. e eee 8
Figure 1-8 Video Board (On Back of Service Door) ..9
Figure 1-9 Flow Chart ............... 00. 10
Figure 1-10 Color Bar
Figure 1-11 Color Bar
Figure 1-12 Color Bar
Figure 2-1 Coin Door ......... 02. ee eee eee eee 16
Figure 2-2 Fuse Replacement ................-- 16
Figure 2-3 Monitor Removal ...........-....245 16
Figure 2-4 Cover Glass Removal ................ 17
Figure 2-5 Printed Circuit Board ................ 7
Figure 2-6 | Power Supply........-.......2..008 17
Figure 2-7 Current Limit Adjustment ............. 18
Figure 3-1 Clock Timing............0.00 2. eee 22
Figure 3-2 Dual Port RAM Timing .........-..... 23 LISTS OF TABLES
Table 1-1
Table 1-2
Table 1-3
Table 1-4
Table 1-5
Table 1-6
Table 1-7
Table 1-8
Table 1-9
Table 1-10
Table 2-1
Table 2-2
Table 2-3
Table 2-4
Table 3-1
Table 3-2
Table 3-3 Self Test Switches ..............2..2., 7
Hardware Tests ...............0 0 eee 8 Video Board ROM Checksum ........... 8
Decoding Jumper Location ............. 8
Video Board RAM Checksum ........... 9
Data/Sound Board ROM Checksum....... 9
Screen RAM Content ................. 11
Audit Totals .......-.. 0.6.00. cece ee 12
Standard Coin Setting ................ 13
Custom Coin Setting ..............0.. 13
Line Voltage ....... 0. 17
Secondary Fuses ..............00000, 18
Data/Sound Board Test Points ......... 19
Video Board Test Points .............. 19
Video Board Memory Map............. 22
Register Initialization .............22.. 23
Data/Sound Memory Map ............. 24
Game Set-Up
“ane™
1, GAME SET-UP
1.1 GAME FEATURES TAITO AMERICA CORPORATION’S ‘QIX”™ upright game is housed in a highly serviceable cabinet designed with many added features. By putting wheels on the cabinet, moving the game from one location to another is made much easier. Alarger security designed cash box has been incorporated into the design of this cabinet. The Control Panel has a polycarbonate overlay, so cigarette marks and mars can be easily wiped clean. This overlay can be replaced if Necessary. The Marquee and Coverglass are made with fully Tempered Glass to minimize breakage. The Back Service Door houses all the PC Boards for the system making servicing of the game, if needed, much easier. Lighted Instructions are provided to further enhance the game and attract players, by making the Instructions easier to read. TAITO AMERICA CORPORATION proudly presents our improved Self-Test capability, making servicing of the game easier, which keeps your game up and running with less down time.
1.2 INTRODUCTION TAITO AMERICA COROPRATION’S “‘QIX’’™ upright game is designed for one or two players. The object of the game is to claim as much screen as possible without getting in the path of the spinning ‘“QIX""™, while avoiding the traveling ‘‘Sparx’’"™. The game is set so a minimum prescribed area must be claimed before moving on to the next screen. The ‘‘Sparx’’™ are timed, which is indicated at the top of the video screen by a Red Timing Line. When the ends of the upper Red Line meet, more ‘‘Sparx’’™ are released. When the alarm sounds these “Sparx’’™ turn into Super ‘“‘Sparx’’™ and become more aggressive and follow the Marker on the outside boarder. If while claiming your area, your Marker is caught in the Spiral Death Trap you will be destroyed, since you cannot cross your own path. If you hesitate and do not complete your area a fuse will be ignited and destroy the Marker. A Slow Draw and Fast Draw Button are provided. If you claim your area using the Slow Draw Button the point values will double.
1.3 GAME INSPECTION TAITO AMERICA CORPORATION’S “‘QIX’’™ upright game is shipped ready for operation, but a last visual check should be made to insure the game is in good condition. Please verify the following before turning the game on. Check the exterior of the game for shipping damage, chips, dents, or broken parts. Open the Rear Service Door and check for any interior damage.
- Make sure there isn’t any damage to the wiring.
- Check Printed Circuit Boards, making sure there is no damage to the components.
- Check fuses making sure they are firmly in their holders.
- Check for loose foreign objects, especially metal objects which may cause electrical problems. Check Plug-in Connectors making sure they are firmly in their sockets.
- Check the Coin Door for any possible damage, especially the switches. The Video Monitor is properly adjusted before shipping. If there are any adjustments necessary, refer to our Video Monitor Manual (72-00009-001). This Manual contains all the Manufacturers recommendations for adjusting the Video Monitor. 1.4 GAME PRE-INSTALLATION The following precautions should be followed when installing the game.
void rough handling of the game, the picture tube is
agile. Install the game on a level surface. Avoid installing the game where it may receive excessive sunlight or heat, to prevent the game from rising internal temperatures. Do not install in a damp or dusty location. For a short time after connecting the power to the game, the picture may be temporiarly distorted. The monitor's purity is affected by the earth’s magnetic field, causing a variation of color. By turning the game on for 10 or 15 seconds and then off for 20 to 30 minutes the automatic degaussing circuit applies a degaussing field around the edges of the Monitor. Doing this several times will correct the problem. Another way to correct this problem is to purchase a degaussing Coil or bulk tape eraser at any Electronics store. This will help to immediately demagnetize the Video tube.
FIGURE 1-1 PROGRAMING PLUG
For safe operation it is recommended the cabinet be grounded. This game is equipped with a three conductor power cable. The third conductor is the ground conductor and when the cable is plugged into an appropriate receptacle, the game is grounded. The offset pin on the power cable’s three-prong connector is the ground connection.
1.5 POWER ON/OFF SWITCH, INTERLOCK SWITCHES, MEMORY PROTECT SWITCH, SELF TEST SWITCH, VOLUME CONTROL, AND SERVICE OUTLET To minimize the hazard of electrical shock while servicing the game a Power ON/OFF Switch, and two (2) Interlock Switches are provided. Two (2) Self Test Switches, a Volume Control and a Service Outlet have also been provided. (See Figures 5 and 6 for location of Switches).
1.5.1 POWER ON/OFF SWITCH, INTERLOCK SWITCHES A Power ON/OFF Switch is located in the front of the game at the botton left side of the cabinet. There are two Power Interlock Switches, one is located on the inside of the Coin Door, the other switch is located at the inside rear of the Service Door. This switch removes all the power from the game without unplugging it from the wall outlet. Power may be restored for servicing by pulling out on the Interlock Switch Buttons.
FIGURE 1-2 POWER ON/OFF SWITCH 1.5.2 MEMORY PROTECT SWITCH The Memory Protect Switch is used to prevent erroneous writes to locations in the CMOS RAM which store the location program variables.
Coin Door Memory Protect Switch
Coin Deor Power Interlock Switch
a
Back Door Power Interlcok Switch
FIGURE 1-3 INTERLOCK SWITCHES & MEMORY PROTECT SWITCH
1.5.3 SELF TEST SWITCH There are two (2) Self Test Switches and four (4) positions, located on the inside of the Coin Door. See Figure 5. The ‘‘QIX"’™ game is capable of testing itself and provides data to demonstrate that the games circuitry and the controls are working properly. For further information on the Self Test Procedure refer to Section 1.8 and Figure 1-8.
ye | @ 8 ue | B : | FIGURE 1-4 SELF TEST SWITCH aby oy @ | ee
SWITCH FUNCTION Up Reset To Factory Setting (Reset Line Lit) Increment Number (Variable Line Lit) Down Decrement Number Move To Next Line Move To The Next Screen Advance Sub-Test Advance Test
TABLE 1-1 SELF TEST SWITCHES 1.5.4 VOLUME CONTROL SETTING The Volume Control Setting is located on the Data/Sound P. C. Board, which is on the rear of the Service Door. The volume increases when turned clockwise as indicated in Figure 1-5.
FIGURE 1-5 VOLUME CONTROL SETTING
1.5.5 SERVICE OUTLET A Power Recepatacle has been provided to further aid servicing. The voltage at this receptacle will be the same as the line voltage the game is set at.
1.6 ELECTRONIC ACCEPTORS This game is equipped with the capability of using 12VDC Electronic Coin Acceptors, such as Third Wave Electronics, Modei TW12 or equivalent. Power for these units may be obtained from the Coin Entry Lamp terminals which provide 12VDC.
1.6.1 COIN METER This game is also equipped with the capability of using a Coin Meter. See Illustration below. Connect one lead to the +12VDC supply (available from the Coin Entry Lamp), another connection from the other lead on the Coin Meter to Connector J15-13 on the ROM/IO Board ns ie 15-13 ojo}ojofofo}
FIGURE 1-6 COIN METER 1.7 GAME INSTALLATION Open the Coin Door and pull out the bottom Interlock Switch. Turn the game on. The language selection frame should be displayed. If the game is in the game mode, push the door switch toward ADV SUB Test. The game will go into self test. If after a minute, the switch test frame is not displayed, refer to the manual on self test after the switch test is displayed, push the door switch toward ADV set four times. Then the language selection frame should be displayed, push the door switch toward ADV SUB Test until the language you want is green. Push the left door switch toward ADV Test and then all the print should be in the language you select. Push door switch toward ADV Test four more times the game should now be in game Mode. For more information on the options the operator can use, see Section 1.8.17 through 1.8.21. 1.7.1 GAME ADJUSTMENTS There are several adjustments you can make to the game to make the play easier or more difficult. First the percentages of screen that needs to be filled can be adjusted anywhere from 0 to 99 percent of the screen. The game is factory set for 75%. The Time Line can also be adjusted from 0 to 99 seconds. The longer the Time Line the easier the game is to play. The shorter the Time Line the harder the game is to play. The game is factory set at 37 seconds. Next the difficulty of each screen can be set independently using settings from Oto 3. Screen1,has 1 ‘‘QIX” and can be set from 0 to 3 the higher the setting the more aggressive the ‘‘QIX’’ become. Screen 2 has 1 “QIX"’. Screen 3 and 4 have 2 ‘‘QIX” per screen. Standard factory settings are, Screen 1 is set at 0, Screens 2, 3 and 4 are set at 1. 7
1.8 SELF TEST PROCEDURE 1.8.1 GENERAL The Self Test Procedure is performed using the two (2) Switches {ocated on the inside of the Coin Door, and the Self Test Button and the LED’S on the Video PC Board. (See Figure 1-7).
FIGURE 1-7 SELF TEST BUTTON
1.8.2 ENTERING INTO THE SELF TEST MODE To enter the Self Test Mode, press the Advance Sub-Test Switch on the Coin Door or the Self Test Button found near the LED display. Allthe LED’S should blink on and the Hardware Tests should start. The Diagnostics can be entered at the Location Programming Screen (Section 1.8.16) by pressing the Advance Test Switch on the Coin Door.if a continual test of the Video Board is desired, press the Self Test Button twice to start the Video Test in the Auto Test Mode. 'n this mode, the machine will continually run the Hardware test until powered off. If the message “OPEN COIN DOOR TO TEST” appears the Coin Door must be opened or a jumper connected across J19, 1-2. This is because the CMOS RAM Test (Section 1.8.6) cannot be performed with the memory protected by the Coin Door Switch.
1.8.3 HARDWARE TESTS These tests are performed in the following order: ; VIDEO BOARD DATA BOARD. ROM Checksum ROM Checksum Communications RAM Local RAM CMOS RAM Communications RAM Color RAM Handshake Test Screen RAM
TABLE 1-2 HARDWARE TESTS
All LED values ate shown Left to Right. 0 is OFF, 1 is ON and X is dependant upon the test results.
1.8.4 VIDEO BOARD ROM CHECKSUM The ROM Checksum calculates the checksum of each Video ROM and compares it to the checksum stored for that ROM. If it differs from the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED’S.
TEST IN PROGRESS: 00 0001
FAILURE: 01 XXXX
LED VALUES:
| LED VALUE | VIDEO | 2716 | 2732 | |
| 01 0000 | A000-A7FF | N/A | US |
| 01 0001 | A800-AFFF | WA | US |
| 01 0010 | BO00-B7FF | NWA | U6 |
| 01 0011 | B800-BFFF | NA | U6 |
| 01 0100 | C000-C7FF | U3 | U7 |
| 01 0101 | C800-CFFF | U4 | U7 |
| 010110 | 0000-D7FF | US | U8 |
| 01 0111 | 0800-DFFF | U6 | U8 |
| 01 1000 | £000-E7FF | U7 | ug |
| 01 1001 | E800-EFFF | U8 | ug |
| 01 1010 | F000-F7FF | ug | U10 |
| 01 1011 | F800-FFFF | U10 | U10 |
TABLE 1-3 VIDEO BOARD ROM CHECKSUM
If the Checksum ROM is bad, it wili show U10 to be bad first. If this test fails, the ROM indicated on the LED display will need to be replaced. The E-PROM Memory in a given game may be implemented as banks of either 2716 or 2732 E-PROMS. The E-PROM type for each bank is selected by the decoding jumper 26-00002-016 for 2716 or 26-00002-032 for 2732.
E-PROM BANK LOCATION VIDEO Ut DATA U22 SOUND u29
TABLE 1-4 DECODING JUMPER LOCATION
1.8.5 COMMUNICATIONS RAM FROM VIDEO BOARD The Communications RAM Test determines the stability of memory shared by the two processors by storing a predefined series of numbers throughout the RAM, then reading it back to insure that it was stored correctly.
LED VALUE: 00 0010
A failure has been detected when the machine halts with the above display. Failure of Communications RAM during Video Board Tests may result from either defective RAM circuitry or failure of the Data Board. To isolate the failure, disconnect the Data Board at P6 and re-enter the test. A failure means trouble in U3, U4 or associated circuits. Passing the retest suggests Data Board problems.
1.8.6 VIDEO BOARD CMOS RAM After saving values in another portion of memory, the CMOS RAM is tested in the same manner as the Communications RAM. If the CMOS RAM passes the test, all of the locations are restored to their previous values.
LEO VALUE: 00 0011
A failure of the CMOS RAM has been detected when the machine halts with the above LED value displayed. If this occurs U85 and U86 or associated decoding should be checked.
1.8.7 VIDEO BOARD COLOR RAM This tests the system Color RAM by storing predefined sequences of numbers in the Color RAM, then reading them back while testing for accuracy.
LED VALUE: 00 0100 -
A failure is indicated by the processor halting with the above value displayed on the LED'S. This signifies the need to check U56, US7 and associated multiplexing and decoding.
1.8.8 VIDEO BOARD SCREEN RAM The Screen RAM is tested by writing a pattern to each page on the screen. The results of these writes is then compared to the original pattern. Any discrepancy causes the machine to halt with the LED displaying the faulty RAM.
| LED VALUE: | TEST IN PROGRESS: | 00 0101 |
FAILURE: 1X XXXX
| [_tep vawud | RAM | 11 XXxX | | RAM | ||
| 10 1000 | | | U2 | 111000 | | | u4s |
| 10.0001 | | | U3z | 410001 | | | ues |
| 100010 | | | ust | 110010 | | | Usd |
| 100011 | | | U30 | 10011 | | | ué3 |
| 100100 | | | u29 | 410100 | | | U62 |
| 100101 | | | 28 | 110101 | | | U6t |
| toaito | | | 27 | 110110 | | | Uso |
| toot | | | U26 | tot | | use | |
| 101000 | | | ut7 | 111000 | | | ude |
| 101001 | | | ute | 441001 | | | U47 |
| 101010 | | | Ut5 | 111010 | | | ude |
| toio11 | | | urd | i11011 | | | us |
| to1100 | | | U1 | 411100 | | | u44 |
| torio1 | | | ut2 | tiitor | | U4 | |
| toro | | | uit | tito | | | uae |
| 10111 | | | Uto | watt | | | ust |
TABLE 1-5 VIDEO BOARD RAM CHECKSUM
Upon failure of a screen RAM, locate the problem RAM and replace it. Exchange the suspected RAM with a known good location to determine if the problem moves with the RAM, IC or whatever the problem is in the supporting circuitry. Futher testing can be done with the Color Bar Test. If this Diagnostic appears to hait without indicating a RAM failure (00.0101 on LED’S), a failure to begin the next test (Data Hardware) is indicated. The interconnection to the Data Processor must be inplace and the Data Processor must be functional to continue.
foxe} ode SELF TEST LEDS
SELF TEST BUTTON a LED VALUE 01 0000 01 0001 01 0010 01 0011 01 0100 01 0101 010110 010111 01 1000 01 1001 01 1010 01 1011
TABLE 1-6 DATA/SOUND BOARD ROM CHECKSUM
If this test fails in the field, the bad ROM will need to be replaced.
1.8.19 DATA/SOUND BOARD LOCAL MEMORY The Data Processor uses a known sequence of numbers to test the bits in its Local Memory. If a bad bit is found the machine will halt with the following display.
LED VALUE: 00.0111
1.8.11 COMMUNICATIONS RAM ADDRESSING The function of this test is to ensure that both the Data and the Video Processor address the Communicatons RAM in the same manner. The Data Processor requests the Video Processor to fill the RAM with a known pattern then, the Data Processor compares the result to the expected pattern. If it does not match, one of the processors is probably decoding the address incorrectly as the RAM itself was previously tested for stability by the Video Processor. The machine will halt with the following display.
LED VALUE: 00 1000
1.8.12 DATA/VIDEO HANDSHAKE This test ensures that the Data Processor can send priority commands via interrupts to the Video Processor. The Video Processor is halted, then restarted by the data Processor after the proper command acknowledgements are received. The machine will halt with the following display.
LED VALUE: 00 1001
1.8.13 SWITCH TEST This screen is used to determine all switches are in working order before entering the switch deperfient self-test screens. The Wiring Diagram supplied with each game will indicate the number associated with a particular switch. The switch number appears in green if the switch is closed and white if it is open. The Advance Test Switch (Switch Number 9) isalways RED in order ~to set it apart from the other switches on the screen. Switches 29, FIGURE 1-8 VIDEO BOARD (ON BACK SERVICE DOOR)
1.8.9 DATA/SOUND BOARD SELF TESTS DATA HARDWARE (ROM CHECKSUM) The ROM Checksum calculates the checksum of each Data ROM and compares it to the checksum stored for that ROM. If it differs from the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED’S.
LED VALUE: TEST IN PROGRESS: FAILURE: 00 0110 01 XXXX
3 and 32 are not used and remain Green. The user should
check all other switches before pressing the Advance Test Switch, as this would move him to the next screen. In addition to the switches required, by the game, the User should be sure to test the Advance Sub-Test, UP and DOWN Switches located in the Coin Door for proper closure as the switches are used to move about in the Self-Tests Screens. To advance to the next screen, activate the Advance Test Button on the Coin Door. }
GAME OVER
SELF TEST ADVANCE ADVANCE SUB-TEST TEST
(raupey | Rom cHEcKsuM| 00 0001—-O1 XXXX
viDEO | BOARD coLor RAM Y 00 0100 SCREEN RAM (FAILURE) 00 01011 XXX
(FAILURED 00 011008 KXXX ROM CHECKSUM LOCAL RAM COMMUNICATIONS RAM HANDSHAKE TEST 00 0118
GRAY SCALE COLOR BARS ALIGNMENT: CONVERGENCE LANGUAGE SELECT LOCATION PROGRAMMING HIGH SCORE TO DATE aupit TOTALS COIN SLOT PROGRAMMING ‘SCREEN TESTS |
GAME OVER
FIGURE 1-9 FLOW CHART
1.8.14 COLOR BALANCE AND INTENSITY ADJUST SCREEN This screen is comprised of two sections. The first section provides a method for adjusting the intensity level of each color gun, and achieving an initial color balance. ‘Three squares, one blue, one green and one red, are drawn along the top of the screen at Maximum intensity and brightness. The color guns should be adjusted so that these squares are barely visible and equal intensity. To complete the color adjustments, a gray scale is provided at the bottom of the screen. Fine tune the color balance with this scale, the double check that the squares at the top are barely visible. To advance to the next screen, activate the Advance Test Switch located on the Coin Door.
1.8.15 COLOR BARS The CPU divides the screen RAM into 16 areas corresponding to 16 bars on the screen. Each area is written with a data value from the Table below. Each value exercise one bit in the Screen RAM. The Color RAM is written with a pattern which outputs each data value with a recognizable color from the Table. All other data values are coded black. This results in a normal screen of 16 color bars per the following table. SS &
sooFF-o-S
$0000 ee PPP Or APS Peo OT AOA PAN PPM PON MANY DLP GP 0 20 PO OOOO gh A9 0% ee MAAN LY, oN
BLU-GRN
aN x ww RAS AS ASS! RNS Ry or
COLOR BAR DIAGNOSTIC
n Feros NORMAL FIGURE 1-10 COLOR BAR
a
&o
TAQUUTOQUUUUUTOREVNLATATUUNUUUTAAUUALA nn COR OP OY OP” GO gO Qh AD PM PP ok © PP oP PP oF WS Soi BLU BLK
BANANAS AS AS 5955 A ASS S &, K 28.0% RS . NAAN GS nN AS ANAS AN AO ON AN NS COCCI ONS ANAS SOO. ere
SFFOO
COLOR BAR DIAGNOSTIC BIT 03 STUCK LOW IN 1-BANK
FIGURE 1-11 COLOR BAR
SCREEN RAM DATA CONTENT © Og (0.0 CCCI! o SEC OCC OROONS Sooo Shoes AON AS Rae OPPS oe ‘ss rosa me S SrrFF SCREEN RAM CONTENT COLOR RAM ADDRESS
COLOR HEX BINARY _| BIT TESTED
COLOR BAR DIAGNOSTIC BIT 5 STUCK HIGH ALL BANKS FIGURE 1-12 COLOR BAR Red Orange Yellow Green Blue Green Blue Violet White Red Orange Yellow Green Green Blue Blue Violet White Black 0000 0001 0000 0010 0000 0100 0000 1000 0001 0000 0010 0000 0100 0000 1000 0000 1111 1110 1111 1101 1111:1011 1114 :0111 1110 1111 1101 1111 10114 1111 0111 1111 XXXX XXXX
TABLE 1-7 NOTRWYHAONMTRwWNYA0
NOTES
If the Self-Test pass, errors in those circuits which affect CPU accesse are ruled out. This leaves latches U91, U94, shift registers U95, U96 and U105-109, direction select U81 and U104 and the CR side of the Color RAM MUX U55, U73, and U74. Stuck bits may be indentified by observing abnormal bars. A bit stuck high will result in black bars (two bit high) on the left or top halt of the screen except for the bar associated with the stuck bit. On the right of bottom half, the bar associated with the stuck bit will be black. The converse is true of a bit stuck low. An error across the entire bar indicates an error in the shift registers, direction select, or color RAM MUX which affects every pixel. Lines of error running crosswise to the bars indicate an error in one bank of RAM of every eighth pixel. To move to the next screen, activate the Advance Test Button. If self test fails, the Color Bars still may by useful. This screen may now be entered without going through on-board self test. Use “Advance Test” to enter the High Score Screen then “Down” to enter the Switch Test. Advance Test may then be used to access the Color Bars. 1.8.16 ALIGNMENT AND CONVERGENCE TEST This screen is provided to align the color guns and correct the convergence on the screen. The screen is composed of a red and a green rectangle and white grid. Adjust the screen width and length so that the red rectangle is slightly within the boundaries of the tube. The adjustmentis to be made on the center of the lines which make up the rectangle. The corners of the rectangle will extend beyond the shadow mask. The green rectangle defines the normal playfield and so should be visible from the players view point. A grid of white squares is provided to help detect and correct any convergence problems the tube may have. Adjust the monitor until the squares are of equal size throughout the screen. To advance to the next screen, activate the Advance Test Button on the Coin Door. 1.8.17 LOCATION PROGRAMMING SCREEN(LANGUAGE SELEC- TION) This screen allows the user to select the language in which the Location Programming and the game will operate. Four (4) languages are provided. Use the Advance Sub-Test Button to move through the offered languages. When the desired language is green, depress the Advance Test Button, to advance to the next screen. {1.8.18 LOCATION PROGRAMMING This screen allows the location to define the difficulty factor for the game. It also allows the location to set a maximum number of credits allowed in the machine prior to a game start up. The user selects the line to be changed by using, the Advance Sub-Test Button until the desired line is changed to green. The value associated with this line is then modified with the UP and DOWN Switch. If the machine is to be reset to the factory settings, use the Advance Sub-Test Button until the reset line is lit in green, then press the UP Switch. The values will be reset and the user will be placed back on the first line for futher adjustments. Advance test will move to the next screen at any time. The backup HSTD (High score to date) value is used to reset the high score on the next screen. Its value will initially determine the score needed for a player to have his own initials show with his score in the high scores. The maximum credit defines a limit for the machine, which when crossed will disable the coin slots. This allows the location to set a limit on the amount of games a player will get if there is a line of people waiting. This value ranges from 1 to 99. However, itshould not be set so close to 99 that a single coin can overflow the credits issued (maximum 99). A Free Play Mode may be selected by setting maximum credits to 0. The credits per coin are set in the coin slot programming screen. &, 1.8.19 HIGH SCORE TO DATE SCREEN This screen shows the scores and initials of the players with the ten highest scores. It is used as an audit for the game. To reset the values to the backup HSTD selected on the previous screen, press the UP Switch. This will also set the initials to “TAC’’. When the UP Button is activated it resets to default scores. To move to the next screen, activate the Advance Test Button on the Coin Door.
1.8.20 AUDIT TOTALS This screen provides the audit totals for the game. Once they are recorded, they may be zeroed by pressing the UP Switch. The following audits are kept.
Total Credits The total number of paid credits issued. This total is never zeroed, but it will wrap around to zero when its total reaches 1,000,000. The only time this total can be zeroed is by physically removing the battery or jumper W1, while the power is off. Left Coins The number of coins dropped into the left slot. Center Coins The number of coins dropped in the center slot. Right Coins The number of coins dropped into the right slot. Paid Credits The number of credits issued for coins. Awarded Credits The number of credits awarded by the game. % Free Plays Awarded credits / paid credits + awarded credits *100 Minutes Played Number of minutes the game has been in play mode. Number of minutes the game has been in extended or awarded play. % Free Time Awarded minutes / minutes played *100. Average Game (Sec)| Minutes played / paid credits + awarded credits *60 The number of times which a player scored high enough to bump someone else from the high score list. Minutes Awarded
High Scores
TABLE 1-8 AUDIT TOTALS
The UP Switch is used to zero the audits. To advance to the next screen, activate the Advance Test Button on the Coin Door.
1.8.21 COIN SLOT PROGRAMMING This screen allows the user to either select a standard coinage setting for the game or program his own. If a standard setting is desired, use the UP and DOWN Switch to adjust the coinage setting while itis lit in green. The values for the variable will change as this number is altered. When the right selection is set, use Advance Test to return to the game. If a non-standard setting is desired, use Advance Sub-Test Switch to move down to the variables so that they may be programmed individually. Once this switch is pressed, the setting number is set to zero to show that the location has supplied their own settings. As the lower variables are unchanged, the user may minimize bis effort by first selecting a setting close to the one he desires. Once in the programming mode, the Advance Sub-Test Switch is used to move among the variables. It wili also take you back to the standard settings, if you press it by mistake. The UP and DOWN Switches are used to increment or decrement the values. Advance Test Switch will return to the game when pressed.
The coin multiplier tells how many coin units are issued for each coin through a particular slot. Coin units for credit show the number of units necessary before a credit is issued. Coin units for bonus gives the number of units necessary before a bonus credit is issued. , . Minimum coin is an optional value which will keep the credits from accumulating until the specified minimum amount of coin units is reached. It is not used in any of the standard settings. 1.8.22 CMOS MEMORY FAILURE If the message “Memory Failure - Service Required’ appears on the screen, the CMOS RAM which stores all of the location programming has failed. All the values stored in the RAM are set back to factory defaults. This condition probably indicates a battery failure or a Failure of U85 or U86. Refer to Section 2 on Maintainence 2.8 CMOS RAM.
STANDARD COIN SETTINGS TABLE 1-9 TTT —
al S/2le2/sle
Si sle@/sl/s)si83 s\/2lseleleiele
([a]3/s/2/8|s|s COIN DOOR MECHANISMS CREDIT/MONEY
| STANDARD | | 17.25, 481 | o1 | or | 04 | 01 | of | 00 | 00 |
17.50, 391, 682 o2 | o1 | 04 | 01 | 02 | 04 | 00 1/.50 fos oi | 04 | o1 | 02 | 00 | 00
| 1 DM, 5 DM | 1/1DM, 6/5DM | 04 | 06 | 00 | 01 | 01 | 00 | 00 |
| 1 FRANC, 5 FRANC | 1/2F, 3/5F ONLY | 05 | or | 16 | 06 | 02 | 00 | 00 |
| 25 CENTS, 1 GUILDER | 1/25, 4/16 | 06 { 91 | 00 | 04 | o1 | 00 | 00 |
| 5 FRANCS, 10 FRANCS | SF, 2/10F | o7 | 01 | 00 | 02 | ot | 00 | 00 |
1/10F 08 | 01 | 00 | 02 | 02 | 00 | 00
| + FRANC, 2 FRANG | 2/1, 6/2F | 09 | 00 | o4 | o1 | 04 | 00 | 00 | |
| 1 UNIT, 5 UNITS | 12, 3/5 | 10 | 01 | 00 | 06 | 02 | 00 | 00 | |
| TWIN COIN | 4/1 COIN | o1 | ot | 04} | 01 | ot | 00 | 00 |
| 4/2 COINS | 03 | {or | 04 { ot | 02 | 00 | 00 |
CUSTOM COIN SETTINGS TABLE 1-10
Ss ae Blela2 »
| 2 | = | 2 | = | s | 2 |
S/s|?/3]s] s/s
| Hl] | al | € | cl | ew | a | cS |
els|8/s)2]2] &
| S/S) | s/2/2] | 2) |
&|=|él2/s/3al|s COIN DOOR MECHANISMS CREDIT/MONEY
| STANDARD | 41/.25, 5/91 | 00] | 01) | 04} | O1 | 01 | 04 } 00 |
| 27.50, 591 | oo | o1| | 04 | or] | o1| | 04] | 02 | |
| 2.50, 41 | oo} | o1| | 04] | o1 | or] | 00 | 02 | ||
| 1/.50, 3/91, 491.25 | oo} | 03] | 12] | 03 | 04] | 15 | 00 | ||
| 17.50, 3/1, 7792 | oof | 12{ | 48] | 12] | 14[ | 96] | 24 |
| 25 CENTS, 1 GUILDER | 147.25, 5/16 | 00 | or | oof | o4| | o1| | 04] | 00 | |
| 100 LIRE, 200 LIRE | 1/200 LIRE | oo{ | a] | oo | o2| | 02] | 00] | 00 |
| TWIN COIN | 4/3 COIN, 2/5 | 00 | 02} | 00 | 02] | 05{ | 00 | oo | ||
| 1 UNIT, 5 UNITS | 11, 5/5 | 00} | o1| | oo | o5{ | 01] | 00] | 00 |
| 173, 215 | 00} | 02] | cof | 10] | 05] | 00 | 00 |
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Maintenance
ALL GAMES REQUIRE A CERTAIN AMOUNT OF MAINTENANCE TO KEEP THEM IN GOOD WORKING ORDER. A PERIODIC CHECK OF THE MECHANICAL CONTROLS WOULD BE BENEFICAL TO THE SUCCESS OF YOUR GAME.
- MAINTENANCE 2.1 CLEANING The exterior of the game, all metal parts and all plastic parts can be cleaned with a non-abrasive cleanser. Caution should be used
- when cleaning the glass, a dry cloth can cause scratches and result in a foggy appearance.
2.2 COIN DOOR The Coin Door used in the “QIX” game needs little or no maintenance, See Figure 2-1. If desired a special coin mechanism cleanser, that leaves no residue, can be obtained from your distributor. Refer to the manufacturers documenation if additional information is needed.
FIGURE 2-1 COIN DOOR
2.3 FUSE REPLACEMENT This game contains 8 fuses. Seven of these fuses can be found on the Power Supply Assembly, five (5) are on the PCB and two (2) are on the Power Supply Bracket. One (1) is \ocated at the bracket where the AC line cord comes into the cabinet. See Figure 2-2 for location of these fuses.
FIGURE 2-2 FUSE REPLACEMENT 2.4 MONITOR REMOVAL If you need to remove the Video Monitor, follow the instructions listed below:
It is recommended the game be left disconnected for at least one hour before removing the video monitor. This will probably discharge the video tube but EXTREME CAUTION is still necessary.
- Disconnect power from the line voltage.
- Disconnect the monitor cable connector.
- Remove the wire cable clamp.
- Take out the two side bolts, one on each side of the cabinet.
- Remove the four mounting bolts and disconnect the green ground wire.
- Slide the Monitor out by pulling the Monitor toward you.
Use EXTREME CAUTION and do not touch electrical parts of the Monitor Yoke area with your hands or with any metal object in your hands! High voltages may exist in any Monitor, even with power disconnected.
FIGURE 2-3 MONITOR REMOVAL
2.5 COVER GLASS REMOVAL To remove the Cover Glass follow the instructions listed below: Remove the Control Panel.
- Loosen three (3) screws on the Cover Glass, front bracket.
- Open Service Door and remove the (Rear) Cover Glass bracket.
- Slide glass out through the Service Door.
FIGURE 2-4 COVER GLASS REMOVAL
2.6 PRINTED CIRCUIT BOARD REPLACEMENT You may wish to remove the ‘‘QIX’’™ printed circuit board, Video Processor (998846), Data/Sound Board (998845), or ROM 1/0 Board (998847) for servicing. Refer to Figure 2-5. The “QIX""™ Printed Circuit Boards (PCB) are located on the inside of the rear service door for easy access. To remove the boards the following steps should be followed:
- Open the rear service door, the power will automatically be removed by the Interlock Switch located on the inside of the door frame.
- Disconnect the connectors from the board or boards you wish to remove.
- Disconnect the ribbon cable, connecting the boards by spreading eject latches on the connector. 4, Remove the screws for the board you wish to remove. FIGURE 2-5 PRINTED CIRCUIT BOARD
2.7 POWER SUPPLY The Power Supply produces all the necessary game voltage requirements. Refer to Figure 2-6 while reading the following circuit description.
FIGURE 2-6 POWER SUPPLY
2.7.1 AC INPUT The AC Input Voltage is applied to the main Power Supply via the AC Line Cords, Line Filter, Line Fuse, Power Switch and Interlock Switch. Different Line Cords are used for 120V and for 240V. The Line Fuse is located on the Line Cord Assembly near the Strain Relief. A Voltage Programming Block is located on the primary side of the Transformer to compensate for high/low voltage conditions. The following line voltages may be inserting the appropriate Programming Plug.
Line Voltage Line Fuse
| 100 VAC + 10% | 50/60Hz | 3 AMP |
| 120 VAC + 10% | 50/60Hz | 3 AMP |
| 200 VAC + 10% | 50/60Hz | 1.5 AMP |
| 220 VAC + 10% | 50/60Hz | 1.5 AMP |
| 240 VAC + 10% | 50/60Hz | 1.5 AMP |
TABLE 2-1 LINE VOLTAGE
For continous protection against fire hazard, replace only with a fuse of the same type having the same electrical rating.
There are five secondary sources. Three go to the Regulator PCB providing +5VDC, +12V0C, —-12VDC, and —5VDC. The other two are fused 6.3VAC used for the incandescent lighting and fused 120VAC used for the monitor, and in certain models for a fluorescent lamp and fan. These secondary fuses are located on the bracket adjacent to the Power Transformer.
Circuit Secondary Fuse
120VAC 2.0AMP SLO-BLO 6.3VAC 2.5AMP
TABLE 2-2 SECONDARY FUSES 2.7.2 —5VDC AND —12VDC REGULATORS The AC Input for the negative voltages comes into the Regulator PCB on J1-5 and J1-6 from the transformer. Fuse F3 protects against short circuits. The AC voltage is then full wave rectified by BRS and filtered by C16. The raw DC is then applied to Reg 1, a three terminal — 12V Regulator. The output of this Regualtor is the —12VDC output for the system and is also the input voltage for Reg 2, a —5V Regulator. The output of this Regulator is the —5VOC for the system. Capacitors C17, C18, C19 are to improve the transient response and stability of the minus voltage regulator. Diodes D8 and D9 provide protection against C18 and C19 being shorted through the Regulator. Resistors R34 and R35 provide current limiting for LED'S 3 and 4 which will light when there is voitage present at the regulation outputs. 2.7.3 +5VDC REGULATOR The AC Input for the +5VDC Regulaior circuit comes in on J1-4 and J1-2, via F1 into BR1. BR1 full wave rectifies the AC Input. This raw DC is applied to the collectors of (2) series pass transistors, mounted on the Heat Sink Assembly, The regulation is done by U3, which is a voltage regulator whose output controls the gain of Q5, which in turn controls the gain of the series pass transistors. The emitter of the series pass transistor return to the Regulators PCB and through R11 and R12, which serve to force current sharing between the series pass devices. The voltage at the output of R11 and R12 are the +5VDC for the system. R11 and Rf2 are voltage set and current foldback adjustments respectively. These are factory adjusted to 5V +.25V. at 7AMPS. Q8, D3 and R20 comprise a SCR-Type Crowbar Circuit which will trigger when the OC output voltages rise above 5.8V. Once the SCR fires, the Power Supply has to be turned off to reset the device. R19 is a current limiter for the voltage indicator LED 1. R16 is used to set the output voltage of the Regulator. C8, D2, R13. and Q4 delay the start-up of the 5V Regulator to allow the —5VDC Regulator to stabilize first. 2.7.4 +12VDC REGULATOR This circuit is essentially the same as the SV Regulator described above. The AC current comes in on J1-3 and J1-4, via fuse F2 into BR2. The AC is rectified by BR2 and filtered by C9. The raw DC is fed to a single series pass transistor on the Heat Sink Assembly and also powers the +12V and +5V Regulator. R28 and R25 are voltage set and current foldback and factory adjusted to 12 Volts +.25V at 4 AMPS. D7, Q9, and R31 are SCR Crowbar Circuits which trigger at 13VDC output which causes supply to go into current foldback. There is an RC delay as in the 5V circuit to delay the +12V rise time. 2.7.5 RESET CIRCUIT The reset circuit will output a 2sec active low MRST pulse at J3-14 J4-14 when the power is first turned ON and whenever power fails for more than 35ms. The reset circuitry is comprised of a Dual Timer (556) and a fullwave type optical coupler across an AC secondary. The output of U1 is the input to one half of the 556 which is configured as a missing pulse detector. Ci and R3 determine the time before the output goes active. This is set for about 35ms. When two or more cycles are missing, the output of the first timer triggers the second timer which drives the MAST low for about 2 seconds. The timer constant for the second timer is set by R4 and C6. Power on reset is generated by C4, and R39 and D12 on the trigger input of the second timer. 3 inverts the signal out of the 556 so it is active low. R7 insures MRST is tow while the power is rising.
2.7.6 POWER SUPPLY ADJUSTMENTS VOLTAGE Adjust voltages on +5V and +12V for +5.00V to +5.05V and +12.00V to +12.05V. CURRENT LIMIT Adjust contro! (5Eand 121) counterclockwise until voltage just changes, then turn contro! clockwise until voltage goes back to original value with pointer, mark position of arrow on potentiometer then turn controi until beginning of 1st notch is aligned with the pointer. On the controls with the Blue Disk turn approximately 30°.
FIGURE 2-7 CURRENT LIMIT ADJUSTMENT
2.9 TEST POINTS The following is a list of Test Points to be used when troubleshooting.
DATA/SOUND BOARD
E Q OMA/BREQ SA 15 DA 15 Voice Clock SBSC DBSC +5V Ground
TABLE 2-3 DATS!
VIDEO BOARD (Master Clock) (Master Clock)
(Address Line) (Address Line)
(Sound Processor Data Enable) (Data Processor Data Enable)
SOUND BOARD TEST POINTS
VIP1_ | Invert VTP2 } 10 MHZ VIP3 | VQ VTP4 | VE VIPS | Extal VTP6 | DMAVBRK VIP7 | VBSC VIP8 | VA 15 (Clock Video Processor) (Clock Video Processor) (External Clock)
(Video Data Enable) (Address Line)
TABLE 2-4 VIDEO BOARD TEST POINTS
If you ground any Data Enable Test Point (DTP7, DTP8, VIP7) the related processor will receive no OP and the address line will act like a 16 Bit Counter.
NOTES
Operation
THIS SECTION PROVIDES A TECHNICAL DESCRIPTION OF THE “QIX”™ GAME. THE GAME ELECTRONICALLY CONSISTS OF PRINTED CIRCUIT BOARDS, TV MONITOR, POWER SUPPLY, AND SPEAKERS WHICH ARE DESCRIBED IN DETAIL IN THE FOLLOWING TEXT.
- THEORY OF OPERATION 3.1 GENERAL The TAITO AMERICA CORPORATION'S arcade video system game is an advanced multiprocessor based circuit utilizing the Motorola 6809E microprocessor. The system is organized in three logical blocks:
A. The Data Processor, which supervises the operation of the entire system. B. The Video Processor, which performs all screen based functions, such as playfield image motion, line drawing, etc. C. The Sound Processor, which generates sounds under the direct control of the Data Processor.
In order to facilitate easy inter-system communications, the Data and the Video Microprocessors run synchronously using clock and timing signals developed on the Video Board. For this reason, discussion will begin by examining the Video Board.
3.2 VIDEO BOARD 3.2.1 SYSTEM CLOCK The fundamental system clock is developed by the 20MHz crystal, inverters U24 and U39, and components. The 20MHz signal is 3.2.2 SCREEN RAM The Video Processor controls a Screen RAM of 256 x 256 pixels with 8 bits per pixel. In order to access of this information, the screen is divided into two pages, top and bottom, chosen under software control. These pages are both addressed at 0800 - 7FFF with address 0 corresponding to the lower left corner of the screen (horizontal scan). All CRT accesses to this RAM are transparent to the processor and the RAM may be read or written any time. The timing of the Screen RAM and the eventual scan is controlled by a 6845/6545/46505 CRT Controller Chip. It's address outputs are gated by U19, U20, U50, and U51 for inversion when used a cocktail table mode. The scan addresses are multiplexed with the address present on the microprocessor address bus by U35, U52, U53, and U54 for standard RAS-CAS accessing. The desired bank of memory is addressed by U87, a one of four decoder. Data written into the Screen RAM comes directly from the system data bus, buffered by 33 Ohm resistors. If a processor read is taking place, the data is placed on the data bus by U77, U78, U79, and U80. First byte, screen reads are latched by 374’s U91, U92, U93, and U94. A second byte screen read is then performed, and this data, together with the data from the first screen read latched by the 374’s is loaded in to the eight (8) 741S299 shift registers. These registers may be shifted in either direction for cocktail table implementation. The byte stream then proceeds to the Color RAM.
divided by the high speed flip flop U38 to obtain a 10MHz main .— clock with a precise 50 percent duty cycle. This 10MHz signal ADDRESS | VIDEO BOARD MEMORY MAP
| generates all other fundamental timing signals ior the video sys- | A. | $3000 | Dual Port RAM |
| tem, including the Data Processor. 1C23 divides the 10MHz signal | B. | $8400 | CMOS Battery Backup Memory |
| to obtain SMHz, 2.5MHz and CCLK, and their respective inver- | c. | $8800 | LED Output and Color RAM Page Select |
| sions. IC’s U9, U37, and U38 combine these signals, presenting | p. | $8coo | Data FIRQ Activation Address |
| them to U25, which synchronizes the output signal to the system | $8C01 | Video FIRQ Deactivation Address |
| 10MHz clock. This circuit produces waveforms whose active edges | E. | $9000 | Color RAM |
| are synchronized to 15ns worse case, 2ns average. | F. | $9402 | Address Latch Hi-Byte |
| The characteristics of the clock circuit may be noted by reference to | $9403 | Address Latch Lo-Byte |
| the Timing Diagram, Figure 3-1. | $9400 | Address Latch Indexed Screen Location |
G. | $9800 Scan Line Readback Location
| ewe | b : | 4! | }H | it | {_} +. | H. | $9C00 | CRT Controller Base Address |
swe 7 yr ree Ean oe : ‘ TABLE 3-1 VIDEO BOARD MEMORY MAP
| eux | “TTP | pepe | pape | peepee a | (S=HEXADECIMAL) |
a a ;—-_—Ss- 3.2.3 DUAL PORT RAM
| e | z | This RAM may be accessed in its entirety by either processor. This | ||
| : | 3 | r | i | is arbitrated as follows: |
| z | = | ic | 1, The Data Processor runs in quadrature with (one quarter | |
| mx | r | clock cycle ahead of) the Video Processor. In other words, | ||
| ie | = | Se | E is inverted for use as DQ, and Q becomes DE. Refer to |
us Timing Diagram. Figute 3-2. ton + 2. The Data Processor, by nature of this timing, accesses the
| wes —I | = | + | Dua! Port RAM % cycle before the Video Processor. At this |
nae + point the Video Processor is guaranteed to not be acces- FIGURE 3-1 CLOCK TIMING sing the RAM. The Data Processor access is flagged by U36, which causes a cycle to be stolen from the Video Processor’s main clock, VQ and VE.
- The Video Processor is unable to access the Duai Port RAM unless the Data Processor is not accessing it as it will not be receiving clocks during that time. The cycle steal is accomplished by the generation of signal DPMUX by U36. This signal directly steals the cycle, and also folds over multiplexers U5, U6, and U21, switching the address lines, R/W and gating signals. U1 and U2 gate the data to or from the disired processor. U22 insures that no spurious writes are generated during foldover.
amasus, 00s ants N v I
FIGURE 3-2 DUAL PORT RAM TIMING
3.2.4 CMOS RAM The CMOS RAM is implemented for use as both a battery back-up storage area and a work area for the Video Processor. The gating U100, U101, U102, and U103 insure that writes to the block RAM from $8700 - 87FF cannot be performed unless the’ Coin Door is open (J19-2 grounded). The 3.6V NiCAD battery is trickle charged by Q8, R64, and R65 when the system is powered. When turned off, supply current for U85, U86, and U100 is provided by this battery. U100 is included to solidly gate the MRST signal and prevent invalid operations during power Up and Down. LED and Color RAM Page Latch, U72 is addressed at address $8800. The upper six bits drive LED’S on the circuit board for diagnostics which cannot be done through the screen. The lower 2 bits select the Color RAM page and will be discussed later.
3.2.5 BI DIRECTIONAL FIRQ CAPABILITY To provide for immediate inter-system communication on demand a Bi-Directional FIRQ Capability has been provided. Any access of address $8C00 by the Video Processor will generate a FIRQ to the Data Processor. Any access of $8C01 by the Video Processor will remove a FIRQ generated by the Data Processor to the Video Processor. This is accomplished by U7, U8, and U9.
3.2.6 COLOR RAM The Color RAM is used as a translation matrix so that a number of different pixel values may access a given color, or to change the color of a given area of the screen without rewriting the Screen RAM. The serial bit stream, eight bits wide, comes from the shift registers of the Screen RAM to be presented to multiplexers U55, U73, and U74. These select between the Video Processor bus and the serial bit stream. As processor access times are considerably greater than the basic bit time (200ns), it is necessary to access this register only during retrace times. Bus read/write occur through U75, and serial output is latched by U76. This Data Stream is converted to a color pallet of 64 colors and four intensities. When the serial bit is selected for access, the two high order bits are provided by the LED output latch. This allows the Programmer to select between four pages of RAM rapidly. 3.2.7 ADDRESS LATCH CIRCUITRY Two methods of Screen Memory Address are provided:
- A 16 bit address may be written into latch U70 and U71 addressed at $9402 and $9403. The addressed location may be accessed by reference to location $9400.
- The high order bit of the latch selects one of two pages which may be directly addressed by reference to locations $0000 - $7FFF. U36, U70, and U71 latch the address. U36 is used in conjunction with U70 as U70 and U71 are tri-stated when inactive. The screen address deposited on the LA bus by U84 and U98 for Processor Bus accesses, and by U70 and U71 for latched address. Decoding is performed by U87 and U88.
3.2.8 SCAN LINE READBACK When read, this location is the number of the scan line currently being drawn by the beam. U34 latches the last row address drawn, and U101 prevents erratic updating at the end of a horizontal line. There are 256 valid scan lines 00 - FF.
3.2.9 CRT CONTROLLER The 6845/6545/46505 is a software programmable sync and scan generator. It has two ports based at $9C00 and $9C01. It is recommended that the reader consult Motorola, Hitachi, Rockwell, or Synertek supplied documentation. Register initialization are as follows: Register | Description | Initialization (decimal)
| RO | Horizontal total-1 | 40 |
| Ri | Horizontal displayed | 32 |
| R2 | Horizontal sync position | 35 |
| R3 | Sync pluse width | 03 |
| R4 | Vertical total-1 | 31 |
| RS | Vertical hold adjust | 17 |
| R6 | Vertical displayed | 32 |
| R7 | Vertical sync position | 32 |
| RQ | Scan lines per row-1 | 07 |
TABLE 3-2 REGISTER INITIALIZATION
All other registers are cleared. The interlace capability which differentiates the various types is not used in this application.
3.3 DATA/SOUND BOARD The Data Processor runs synchronously to the Video Processor, as was described in this (Section Dual) Port Memory. All basic timing signals originate on the Video Processor Board and are bussed onto the Data Processor Board. The Sound Processor and Amplifier circuitry also resides on this Board.
3.3.1 MEMORY MAP The following devices are available for access to the Data Processor.
Dua! Port Memory Local Memory ACIA Base Address Video FIRQ Activation Address Data FIRQ Deactivation Address Sound PIA Game PIA 1. Game PIA 2. Game PIA 3.
TABLE 3-3 DATA/SOUND MEMORY MAP (S=HEXADECIMAL) 3.3.2 DUAL PORT MEMORY See discussion of Dual Port Memory under Video Processor Heading (Section 3.2).
3.3.3 LOCAL MEMORY . This is a 1K block of memory, U15 and U76, provided for scratch and work area for the Data Processor. romm GOGF
3.3.4 ACIA A Motorola 6850 ACIA has been provided for diagnostic and other communications. Timing is generated by crystal oscillator Y1 - U23 and prescaled by U27 and U26. SW1 may be configured to allow one of eight baud rates (2 speeds may be software selected in the ACIA). Correct RS-232 jevels are provided by U25 and U21.
3.3.5 BI-DIRECTIONAL FIRQ CAPABILITY Any access of $8C00 will generate a FIRQ to the Video Processor. Any access of $8C01 will remove FIRQ generated by the Video Processor to the Data Precessor. This is accomplished by U7, U8, and U9, which resides on the Video Board.
3.3.6 SOUND PIA Both ports of PIA U20 have been dedicated to the control of the Sound Processor. Port Ais used fo select a sound number, which is initiated by strabbing the U20 (CA2) - U8 (CA1) interrupt line. Responses can be made using the reverse U8 (CA2) - U20 (CA1) interrupt. Port B is used to control the amplitude of the generated sound to the Stereo Amplifiers. The output of side B go to U24 and U28, which vary the ratio of the voltage divider across the noninverting inputs of U29 and U30. This allows balance control of the sound to coincide with real time events occuring on the screen.
3.3.7 GAME PIA’S Three 6820's are provided for interfacing with Play Controls and Coin Door Switches. These are located on the Game Board and are accessed through a Jumper Cable J16 and J15 respectively. 3.3.8 SOUND PROCESSOR A Motorola 6802 also resides on the Data Board for sound generation. This Processor runs at 3.68MHz and accesses only two devices, PIA’S U7 and U8. U8 as mentioned previously, interface to the Data Processor. It also is the digital to analog output of the Sound Processor. Data from Port B is presented to U13. The current based output is converted to a voitage output by Q1, and controlled in amplitude by a potentiometer placed across J8. Speech circuitry is mixed with sound by R9, and the sum is sent to the Amplifiers. U7 controls the speech synthesis chip U19. The
speec signal is shaped and filtered by the multipole bandpass filter
18.
3.4 ROM//0/ BOARD This board contains the Program ROM for both the Data, Video and Sound Processors, along with the PIA’S needed to interface control, coils, lamps, etc.
3.4.1 GAME PIA’S Three Game PIA’S are located on this board $9400, $9900, $9C00. These devices, U11, U20, and U30 respectively, interface through naise control circuits A or B filters for those lines dedicated to inputs. Eleven (11) High Current Drivers have been provided utilizing circuit C. Each of these is capable of switching a 1.5AMP/ 24Volt DC load to ground.
3.4.2 ROM’S Eight ROM locations are provided for the Data Processor, U12 - U19. These are selected by U2. Eight ROM’S, U3 - U10 selected by U2 are dedicated to the Video Processor. Sounds are supported by ROM’S U25, U26, and U27, with select U28. ROM Bank U3 - U10 may consist of either 2716 or 2732 type EPROMS as determined by a jumper plug inserted in U1. It is assumed that all such EPROMS in the bank are of the same type. Likewise, ROM Bank U2 - U79 is determined by jumper plug at U22 ROM Bank jumpering for 2716's is as follows: Pin 1-14, 2-13, 3-12, 4-11 and 5-10. The highest address EPROM is U10, U19, or U27 in each bank with addresses of adjacent sockets progressing downward in $800 byte blocks. dumpering for 2732's is as follows: Pin 2-14, 3-13, 4-12, 5-11, and 6-10. The highest address EPROM is Ut0, U19, or U27 in each bank with addresses of adjacent sockets progressing downward in $1000 byte blocks.
3.5 SOFTWARE SECURITY MODULE ENCRYPTION MODULE Taito America’s video system is designed to operate with a proprietary Encryption Module taking the place of the CPU. This 40-Pin Module has the same logic and timing charecteristics as the 6809E CPU it replaces, however, the module permits operation codes stored in EPROMS to be inciphered. Troubleshooting is accomplished either through the Self Test capability discussed in Section 2 or by use of the ‘Taito Tech” Test Set which provides additional tests, monitor functions and Support signature analysis by means of a self contained 6809E CPU.
illustration
Parts Lists
INCANDESCENT PANEL
ITEM TAITO PART NO. DESCRIPTION 27-00005-001 Lamp #455 (Flasher) 27-00006-001 Lamp #47 26B00009-001 Bayonet Base Socket afe)el— 26800009-001 Marquee Lighting Plate
toth Sok
4-WAY JOYSTICK
| ITER TAITO PART NO. DESCRIPTION 63A00031-001 Ball & Shaft 63A00021-001 Mask 63000027-001 Mounting Plate 62A00002-001 Shock Mount Pad 63A00028-002 Switch Plate 63A00030-001 Actuator 61A00078-001 “L" Bracket 63A00026-001 Switch Spacer ole) nlala}s}olr
29B00016-002 Leat Switch 63A00029-001 Spacer
CONTROL PANEL
TAITO ITEM PART NO. DESCRIPTION 1 63B00031-001 | Ball & Shaft 2 63B00024-002 |Push Button (Red) 3 07M00051-001 | Control Panel 4 63B00024-001 | Push Button (White) 5 63C00025-001 | Switch Support 6 54A07001-008 | Stamped Nut 54-11 7 29B00016-001 |Leaf Switch 8 42D00017-001 |Dash Panel 9 | 63000032-004 [Control (4-Way Leaf Switch) 10 63B00030-001 | Actuator 1 59B00020-017 |'E”” Ring 12 61A00015-001 | Strike Hook ~ 7 13 12B00108-001 | Cleat 14 63-00050-001 | Decal, Lexan
*Item not shown on drawing.
CONTROL PANEL
m———
DOOR ASSEMBLY
TAITO ITEM PART NO. DESCRIPTION 1 42D00067-001 Door Assembly 04-00037-002 Lock Kit 61B00142-001 Lock Rod Assembly 61D00079-001 P.C. Board Mounting Plate 61A00111-001 Rod Lock Bracket ola) a} o}nm 08M00018-001 Game P.C. Board Assembly 7 79-00031-001 L.E.D. Values Sheet
*Item not shown on drawing.
NOTES
DOOR ASSEMBLY
CABINET ASSEMBLY UPRIGHT FRONT VIEW
TAITO ITEM PART NO. DESCRIPTION 1 07M00055-001 | Incandescent Panel 2 63B00006-001 | ‘“U’’ Channel Bracket 3 47D00012-002 | Marquee 4 61C00115-001 | Marquee Retaining Bracket 5 61D00012-001 | Lower Cover Glass 6 07M00052-001| Contro! Panel Assembly 7 07-00050-001 | Coin Door 8 61B00113-001 | Switch Bracket 9 07M00057-001| Service Switch Assembly 10 29-00022-001 | Slide, Center Return Switch al 29B00015-001 | interlock Switch 12 61B00114-001 | Interlock Switch Bracket 13 59-00008-001 | Latching Clamp 14 63B00002-004 | ‘T"’ Molding 15 29A00023-001 | Power ON/OFF Switch 16 41D00009-001 | Finish Cabinet
CABINET ASSEMBLY UPRIGHT FRONT VIEW
CABINET ASSEMBLY UPRIGHT REAR VIEW
TAITO ITEM PART NO. DESCRIPTION 42D00069-001 |Door & Board Mounting Assembly 42D00016-001 |Door Panel 21C00003-001 |Speaker 6” round 61B00027-001 | Speaker Grill 41000009-002 [Finished Cabinet 61800057-001 |Leaf Hinge
63C00035-001 [Monitor Shroud 61C00080-001 |Monitor Mounting Bracket 27-00006-001 |#47 Bulb, Lighted Instr. 7 61C00006-001 |Upper Cover Glass Bracket x E}
a] 47D00013-002 |Cover Glass 12 44C00001-001 | Wheels 13 63C00005-004 |‘‘L’* Molding 14 07M00042-001 |A/C Line Cord Assembly 15 63C00005-022 |‘'L’’ Molding 16 61B00030-002 |Interlock Bracket 17 29B00015-001 |Interlock Switch 18 07M00039-001 | Power Supply 19 61C00054-001 |Cash Box Lid -| 20 61B00056-001 |Leaf Hinge 2 61A00055-001 [Hinge Pin 22 31-00006-001 | 19” Color Monitor 23 63-00019-001 |Cash Tray Separator 24 61-00039-001 |Cash Tray Handle 25 61C00060-001 |Cash Box 26 63-00010-001 | Cash Tray (Only) 27 07M00054-001 | Cash Tray Assembly 28 42000013-001 | Monitor Support Cleat 29 61C00086-001 |Corner Bracket 30 08-00002-001 |Data/Sound P.C.B. 31 61B00142-001 |Lock Rod Assembly 32 08-90003-001 |ROM/O P.C.B. 33 04M00037-002 | Lock Kit 34 08-00001-001 |Video Processor P.C.B. 35 61D00079-001 |P.C.B. Mtg. Plate
CABINET ASSEMBLY UPRIGHT REAR VIEW
\
FI =| * Cane SAsa ISA c=T .
awl gage Lae CO Qoeg POWER SUPPLY COMPONENT LAYOUT
08-00007-001 ° *@ oe ee os wa aicyone | TEE
BEBEBE mae (C) +51 +5¥ +12V +l2r cle
17, Fa
FS
fo ok
(oa
POWER SUPPLY
| TAITO | TAITO | F | ||
| SYM | PART NO. | DESCRIPTION | SYM | PART NO. | DESCRIPTION | |
| RI | eerie | Resistor 1.0K 5% YaW 5% | {cs | 12-10001-102 | Capacitor, .0O1uf |
| R2 | 11-00001-512 | Resistor 5.1K YW 5% | C6 | | 12-30001-106 | Capacitor, Tantalum 10uf | ||
| R3__} | 11-00001-183 | Resistor 18K “MW 5% | C7 =| 12-20003-509 | Capacitor, Electrolytic 50 ,000ut |
R4 | 11-00001-224 | Resistor 220K YW 5% €8 | 12-30001-105 | Capacitor, Tantalum 1.uf 35V
| R5__| | 11-00001-472 | Resistor 4.7K %4W 5% | C9 | 12-20003-209 | Capacitor, Electrolytic 20,009ut | |
| R6 | | 11-00001-222 | Resistor 2.2K VW 5% | [c10 | 12-10001-332 | Capacitor, Ceramic .0033uf |
R7 | 11-10001-101 | Resistor 100 %4W 5% C11 | 12-30001-476 | Capacitor, Tantalum 47uf R8 | 11-00001-102 | Resistor 10K %4W 5% C12 | 12-30001-105 | Capacitor, Tantalum 1.uf 35V [RQ _| 11-00001-472 | Resistor 4.7K YaW 5% C13 | 12-10004-103 | Capacitor, Ceramic .O1uf
| R10 | 11-10001-151 | Resistor 100 YW 5% | C14 | 12-10001-102 | Capacitor, .0O1uf | ; |
R11 | 11-30001-015 | Resistor .15 4W 5% C15 | 12-30001-476 | Capacitor, Tantalum 47uf R12 | 11-30001-015 | Resistor -15 4W 5% C16 | 12-20002-108 | Capacitor, Electrolytic 1,000uf R13 | 11-00001-472 | Resistor 4.7K YW 5% C17_ | 12-30001-225 | Capacitor, Tantalum 2.2uf 25V R14 | 11-00001-222 | Resistor 2.2K %4W 5% C18 | 12-30001-225 | Capacitor, Tantalum 2.2uf 25V
| R15 \1 1-00001-222 | Resistor 2.2K %4W 5% | C19 | 12-30001-105 | Capacitor, Tantalum 1.uf 35V | 7 | ||
| RIG | 11-60001-252 | Pot 2.5K 4W 20% | Fi | | 24-00003-010 | 10A Fuse | ||
| R17 | 11-00001-222 | Resistor 2.2K %4W 5% | F2 | 24-00003-010 | |10A Fuse | | |
| R18 | 11-60001-102 | Pot 1.0K %4W 20% | F3 | | 24-00003-003 | Fuse, 2A |
R19 | 11-00001-511 | Resistor 510 Y4W 5% F4 | 24-00003-004 | Fuse, 4A
| R20 | 11-10001-470 | Resistor 47 %W 5% | [FS | 24-00003-004 | Fuse, 44 | | |
| R21_| | 11-00001-162 | Resistor 1.6K %W 5% | BR1_} | 13-00100-025 | Diode Bridge 25A, 100V |
| R22 | |11-00001-103 | Resistor 10K %W 5% | BR2 | 13-00100-012 | Diode Bridge 12A, 100V |
R23 | 11-00001-472 | Resistor 4.7K YW 34 BR3 | 13-00100-002 | Diode Bridge 2A, 100V
| R24 | 11-00001-222 | Resistor 2.2K %4W 5% | D1 | | 13-14002-001 | Diode IN4002 |
| R25 | 11-60001-102 | Pot 1.0K YW 5% | D2; | 13-14002-001 | Diode IN4002 |
| R26 | {11-00001-472 | Resistor 407K YW 5% | D3 | 13-10752-001 | Diode, Zener IN752 |
R27 | 11-00001-222 | Resistor 2.2K %4W 5% D4 | 13-14002-001 | Diode N4002
| R28 | 11-60001-252 | Pot 2.5K YaW 20% | D5 | _| 13-14002-001 | Diode IN4002 |
R29 | 11-00001-472 | Resistor 4.7K 4W 5% D6 | 13-14002-001 | Diode IN4002 R30 | 11-00001-122 | Resistor 1.2K YW 5% [07 | 13-10964-001 | Diode, Zener INS64 R31_ | 11-10001-470 | Resistor 47 Y4W 5% 7 D8 | 13-14002-001 | Diode IN4002 R32 | 11-30001-015 | Resistor .15 4W 5% D9 | 13-14002-001 ] Diode IN4002
| R33} | 11-00001-222 | Resistor 2.2K 4W 5% | D10 | 13-14002-001 | Diode IN4002 |
| R34 | |11-00001-122 | Resistor 1.2K %4W 5% | Dit | 13-14002-001 | Diode IN4002 |
| R35 | _|11-00001-511 | Resistor 510 %4W 5% | D12 | 13-14002-007 | Diode IN4002 |
R36 | 11-00001-222 | Resistor 2.2K YW 5% LED1| 13-00001-001 | LED (Red) R37 | 11-00001-104 | Resistor 100K LED2| 13-00001-001 | LED (Red)
| R38 | |11-00001-103 | Resistor 10K %4W 5% | LED3} 13-00001-001 | LED (Red) |
R39_|11-00001-224 |} Resistor 220L Y4W 5% | LED4} 13-00001-001 | LED (Red)
| Ci | | 12-30001-225 | Capacitor, Tantalum 2.2uf 25V | U1 | 15-62500-001 | Opte Coupler H11AA2 |
| C2 | 12-10004-i03 | Capacitor, Ceramic .O1uf | U2 | 15-50556-001 | Timer (Dual) 556 | _| |
C3 | 12-10004-103 | Capacitor, Ceramic .Ot1uf U3 | 15-50723-001 | Voltage Regulator 723 C4 | 12-30001-105 _{Capacitor, Tantalum 1.uf 35V U4 | 15-50723-001 | Voltage Regulator 723
POWER SUPPLY
TAITO ‘SYM | PART NO. DESCRIPTION REG1 | 15-57912-001 | Voltage Regulator 7912 REG2] 15-57905-001 | Voltage Regulator 79L05 Qt = | 14-22905-001 | Transistor 2N2905 02 [14-22905-001 | Transistor 2N2905 Q3 | 14-22905-001 | Transistor 2N2905 4 | 14-22905-001 | Transistor 2N2905 Q5 | 14-23055-001 | Transistor 2N3055 Q6 | 14-22905-001 | Transistor 2N2905 [a 14-20030-001 | Transistor TIP-30A Q8 | 14-26401-001 | SCR 2N6401 Q9 | 14-26401-001 | SCR 2N6401 J1_ | 25-00022-006 | Connector, 1-380999-0 6Pin J2 | 25-00022-008 | Connector, 350212-1 8Pin J3_—_ | 25-00002-014 | Connector, 09-60-1141 14Pin J4 | 25-00002-014 | Connector, 09-60-1140 14Pin 24-10001-001 | Fuse Clips | 30-00220-002 Heat Sink Dual To-220 —| 30-00003-001 | Heat Sink Single To-3
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
VIDEO PROCESSOR
] Tarto TAITO SYM] PARTNO. | DESCRIPTION SYM |PARTNO. | DESCRIPTION
| C1 | | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-—20% | C55 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% |
C2 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C56 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C3 | 12=10002-104 Capacitor Ceramic, .1uf,50V, +80/—20% C57 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| C4 = | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | | | C58 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% |
5 | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20% 59 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—36 C6 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C60 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% \c7__|12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/--20% 61 | 12-30001-106 | Capacitor Tant, 10uf, 16V C8 | 12-19002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C62 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C9 | 12-30001-106 | Capacitor Tant, 10uf,16V C63 | 12-30001-106 | Capacitor Tant, 10uf, 16V C10 } 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% ~ | C64 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C11 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C65 | 12-10001-471 | Capacitor Ceramic, 470uf,50V, 10% X7R €12_ | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—-20% Axial Lead 013 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | C66 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| 14 | 12-10003-101 | Capacitor Ceramic, 100pf, 10% NPO Axial Leadl | C67_| | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% |
| C15 | |12-10002-104 | Capacitor Ceramic, .1uf,50V, + 80/— 20% | C68 _| 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% |
616 | 12-10002-104 | Capacitor Ceramic, . 1uf,50V, +80/-20% | C69 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 617 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C70 _| 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20%
| 18 | 12-10002-104 | Capacitor Ceramic, .uf,50V, +80/—20% | C71; | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% |
| 19 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | C72 | _|12-10002-104 | Capacitor Ceramic, -1uf,50V, +80/—20% |
20 | 42-10002-104 | Capacitor Ceramic, .1uf,50V, +80/— 20% C73 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%
| Cat | _[42-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% | G74 | 12-10002-104 | Capacitor Ceramic, -tuf,50V, +80/—20% |
| roan | 72-30001-106 | Capacitor Tant, 10uf, 16V | C75 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% |
| [{c23_[12-10002-104 | Capacitor Ceramic, uf SOV, + 80/— 20% | G76_{ | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/— 20% |
| 626 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20% | C77_| | 12-0001-106 | Capacitor Tant, 10uf, 16V |
27 | 12-10002-104 [Capacitor Ceramic, 1uf,50V, +80/- 20% C78, | 1210002-104 | Capacitor Ceramic, -tuf.GV, +80/— 20% 28 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/-20% C79 _| 12-10002;104 | Capacitor Ceramic, tuf,50V, +80/— 20% 29 | 12-10002-104 | Capacitor Ceramic, .tuf,S0V, +80/—20% [80 _| 12-30001-106 ! Capacitor Tant, 10uf, 16V
| 630 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% | CB1_| | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/— 20% | |
| 31 | 12-10003-101 | Capacitor Disk 100pf, 10% NPO | ~} | C82_| | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% |
| 32 | {12-10002-104 | Capacitor Ceramic, .Tuf,50V, +80/—20% | £83_ | 12-10092-104 | Capacitor Ceramic, -1uf,50V, +80/—36 |
633 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% C84 _| 12-10002-104 | Capacitor Ceramio, tuf,50V, + 80/—20%
| 34 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +60/—20% | | C85_| | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | |
| 635. | |12-10002-104 | Capacitor Ceramic, .uf,50V, +80/—20% | $86 | 12-10002-104 | Capacitor Ceramic, Tuf,60V, + 80/~20% | |
| 36 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | C87_| | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% | |
| €37_{ | 42-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% | 8B | 12-20001-107") | Ganaetior Electrolyte, 100ut,2BV, |
| 638 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% | 89] | 12-80001-107 | Capacitor Electroytio, 100ut 25V, |
C39 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% +100/—20% C40 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C90 | 12-20001-197 | Capacitor Electrolytic, 190uf,25V, C41 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/--20% +100/—20% C42 | 12-10002-104 | Capacitor Tant, 10uf,16V C91 | 12-10002-104 | Capacitor Ceramic. .1uf,50V, +80/—20%
| C43. | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | C92_| | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20% |
| 44 | 12-30001-106 | Capacitor Tant, 10uf,16V | | | C93 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% |
45 | 12-30001-106 | Capacitor Tant, 10uf, 16V 694 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C50 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C95 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C51 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C96 | 12-10001-471 panecl earam, 470pf,50V, 10% X7R C52 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% - - 53 | 12-10002-104 | Capacitor Ceramic, Tuf,60V, +60/—20% G87 | 12-10001-471 | Capactor Ceramic, 470, 5OV,10% KIR 54 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 98 | 12-10001-471 | Capacitor Ceramic, 470pf,50V,10% X7R Axial Lead
VIDEO PROCESSOR
TAITO TAO
| | sym | PART NO. | | DESCRIPTION | syM| PART No. _| DESCRIPTION | | |
| C99 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | R37 | 11-00001-473 {Resistor 47K OHM, YW, 5% |
100] 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% R38 | 11-00001-332 | Resistor 3300 OHM, AW, 5%
| C101 12-40003-100 | Capacitor Ceramic, 10pf,10% NPO Axial] | | R39} | 11-00001-331 | Resistor 330 OHM, AW, 5% |
Lead 20% R40 | 11-00001-331 | Resistor 330 GHM, aW, 5% C102} 12-10002-104 | Capacitor Ceramic, .1uf,S0V, +80/~20% R41 | 11-00001-331 | Resistor 330 OHM, 14W, 5%
| £108 | 12-19002-104 | Capacitor Ceramic, tuf,50V. +80/—20% | R42_| | 11-00001-331 | [Resistor 330 OHM, YW, 5% |
C104 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% R43 | 11-00001-331 | Resistor 330 OHM, %W, 5%
| C105 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | R44 | 11-00001-331 | Resistor 330 OHM, YAW, 5% | a |
C106 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% R45 | 11-00001-151 | Resistor 150 OHM, 14W, 5% C107 11002 04 Capacitor Ceramic, .1uf,50V, +80/--20% R46 | 11-00001-820 | Resistor 82 CHM, AW, 5%
| C108 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20% | par | ["bo001-e71 | padicior 470 OHM, MW, Sie | 4 |
C179] 2-10001-471 | Cepactor Geran, SOV, 10% A7OPF aa | HDO0DIT61 | Gecko? 180, OHM TANT 6%
| R1_| | 11-00001-330 | Resistor 33 OHM, UW, 5% | ~ | ee ee | = |
R2_| 11-00001-152 | Resistor 1.5K, WW, 5% eels
| R3_| | 11-00007-271 | Resistor 270 OHM, AW, 6% | oa | oe ae = 2 |
aT 53 | 11-00007-330 | Resistor 33 OHM, Yaw, 5%
| [RS | TY G000 271 | Resistor 270 OHM, HAW. 6% | R54 | 1-00001-390 [Resistor 33 OHM, TaW, 5% | |||
| | | ES | sae | ests | S20 | E5_|17-00001-390 | Resistor 33 OHM, WW. 5% |
| ce | ee | 56 | 17-00001-330 | Resistor 33 OHM, YW, Bie |
BE _| 1 00001-228 | Resistor 2.76, YW, 574 R57 | 11-00001-360 | Resistor 63 OHM, HW, 5%
| 89 _| 11-00007-330 | Resistor 33 OHM, “AW, 5% | FE | goon ga | Ream SS ORM HWE | = |
EE SD | Resist 208M R59 | 11-00007-473 | Resistor 47K OHM, YW, 5% Rit |11-00001-330 | Resistor 33 OHM, 7AW, 5% i a Ri2 | 11-00001-330 | Resistor 33 OHM, AW, 5% R60 | 11-00001-332 | Resistor 3300 OHM, %4W, 5% : R61 | 11-00001-301 | Resistor 390 OHM, 14W, 5%
| R13 | 11-00001-820 | Resistor 82 OHM, YW, 5% | Rea | 11-00001-332 | Resistor 3.3K, UW. 5% | —| | |
| R14 | 11-00001-181 | Resistor 180 OHM, AW, 5% | SS | ear | eoe ae |
| R15 | 11-00001-271 | Resistor 270 OHM, YAW, 5% | Ter | ieamociar | thea OF AW BE |
| BOG | U-O0001 151 | Resistor 150 OHM, MW, 5% | R65 | |11-00001-151 | Resistor 150 OHM, Yaw, 5% |
R17 | 11-00001-151 | Resistor 150 OHM, %4W, 5% = = 4
| R18 | 11-00007-271 | Resistor 270 OHM, YW, 5% | R6H_| | 11-00001-992 | Resistor 3.38 YW, 26 | |
| R19_|11-00001-181 | Resistor 180 OHM, Taw, 5% | Ber | te papor sae | restore a a oh |
| R20 | 17-00001-820 | Resistor 82 OHM, YAW, 5% | | | | | ee |
R21_|11-00001-330 | Resistor 33 OHM, YAW, 6% a
| R22_|11-00001-330 | Resistor 33 OHM, UW, 5% | __| | > es | 4 | ||
| R23} | 11-00007-330 | Resistor 33 OHM, AW, 5% | A | ee a | ||
| R24_|11-00001-330 | Resistor 33 OHM, YAW, 5% | leer | iepoon por Teese besa | |||
| R25_|11-00007-330 | Resistor 33 OHM, YAW, 5% | ae | homeaor teenie bem | |||
| R26 | 11-00007-330 | Resistor 33 OHM, YW, 5% | ae | Tour oor toate Bead | |||
| R27_{11-00001-330 | Resistor 33 OHM, AW, 5% | bey | -tPpocaroor | tone brag | ||
| R28_[11-00001-181 | Resistor 180 OHM, TAW, 5% | rast | raoooranr | Thesis Bena | ||
| R29 | 11-0000/-471 | Resistor 470 OHM, “AW, 5% | a | angonaarT | Fete eens | ||
| RG0_|11-00001-471 | Resistor 470 OHM, WW, 5% | rio 17 booooor | [terns Bea | |||
| R31_|11-00001-471 | Resistor 470 OHM, YAW, 5% | ty onaprapr | seems bean | = | |||
| 735 | Somat | ee = 2 | Q1 | 14-23904-001 | Transistor NPN Silicon (2N3904) | ||
| Raa | 117,00001-681 | Resistor 680 OHM. va, a% | Q2 | 14-23904-001 | Transistor NPN Silicon (2N3904) | ||
| Ras | 111-007-391 | Reslstar 490 OM, YAW. Sve | —| | | 03 _| 14-23904-001 | Transistor NPN Silicon (2N3904) | | |
. ~ * 04 | 14-23904-001 | Transistor NPN Siticon (2N3904) R36 | 11-06001-330 | Resistor 33 GHM, YW, 5%
TAITO TAITO
| SYM | PART NO. | DESCRIPTION | SYM |PART NO. | DESCRIPTION |
Q5 | 14-23904-001 | Transistor NPN Silicon (2N3904) U11 |15-10001-001 | RAM 16K x 1 Dynamic (4116) Q6 | 14-23904-001 | Transistor NPN Silicon (2N3904) '26-00001-016 | Socket DIP 16 Pin for U11 Q7 | 14-23904-001 | Transistor NPN Silicon (2N3904) U12 |15-10001-001 | RAM 16K x 1 Dynamic (4116) Q8 | 14-23905-001 | Transistor NPN Silicon (2N3905) 26-00001-016 | Socket DIP 16 Pin for U12
| LED1 | 13-00001-001 | |L.E.D. RED, TL-1% | U13 |15-10001-001 | RAM 16K x 1 Dynamic (4116) |
| LED2 |13-00001-001 | }L.E.D. RED, TL-134 | 26-00001-016 | Socket DIP 16 Pin for U13 |
| LED3 | 13-00001-001 | |L.E.D. RED, TL-1% | U14 }15-10001-001 | RAM 16K x 1 Dynamic (4116) |
| LED4 | 13-00001-001 | |L.E.D. RED, TL-1%4 | 26-00001-016 | Socket DIP 16 Pin for U14 |
| LEDS |13-00001-001 | |L.E.D. RED, TL-1% | U15 |15-10001-001 | RAM 16K x 1 Dynamic (4116) |
| LED6 |13-00001-001 | |L.E.D. RED, TL-1% | 26-00001-016 | Socket DIP 16 Pin for U15 |
Y1 — |19-00003-001 | CRYSTAL, 20,000MHZ U16 |15-10001-001 | RAM 16K x 1 Dynamic (4116) BATT |20-00001-001 | Battery, NICAD, 3.6V, 1/3 AA 26-00001-016 | Socket DIP 16 Pin for U16
| SW1 | |29-00017-001 | Switch Momentary | U17 |15-10001-001 | RAM 16K x 1 Dynamic (4116) | |
| TP1 | {59-00021-001 | Test Point | 26-00001-016 | Socket DIP 16 Pin for U17 | |
| TP2 | |59-00021-001 | Test Point | U18 | 15-00003-001 | CRT CONTROLLER 68A45 | |
| TP3 | |59-00021-001 | Test Point | 26-00001-040 | Socket DIP 40 Pin for U18 | |
| TP4 | |59-00021-001 | Test Point | U19 |15-20086-001 | Quad 2 Input Exclusive or (74LS86) | |
| TPS | |59-00021-001 | Test Point | U20 }15-20086-001 | Quad 2 Input Exclusive or (74LS86) | |
| TP6 | |59-00021-001 | |Test Point | U21 |15-20157-001 | Multiplexer Quad 2-Input (74LS157) |
| TP7 | |59-00021-001 | Test Point | U22 }15-20032-001 | Quad 2 Input or (74LS157) | |
| TP8 | |59-00021-001 | Test Point | U23 |15-20161-001 | Counter, 4 Bit Presetable (74LS161) | |
| RP1 | |11-50001-102 | 1K OHM Resistor Sip Pack | U24 |15-20004-001 | Inverter, HEX (74LS04) | |
| RP2 | |11-50001-473 |47K OHM Resistor Sip Pack | U25 | 15-70374-001 | Latch, Octal Shockey (74LS374) | |
| RP3_ | |11-50001-332 |3.3K Resistor Sip Pack | U26 |15-10001-001 | RAM 16K x1 Dynamic (4116) | |
| RP4 | |11-50001-332 | 3.3K Resistor Sip Pack | 26-00001-016 | Socket DIP 16 Pin for U26 | |
| RP§ | |11-50001-332 |3.3K Resistor Sip Pack | U27 |15-10001-001 | RAM 16K x1 Dynamic (4116) |
J1 —_ |25-00001-014 | Connector, 14 Pin .156 Center 26-00001-016 | Socket DIP 16 Pin for U27 J2 — |25-00002-014 | Connector, 14 Pin .156 Center U28 | 15-10001-001 | RAM 16K x1 Dynamic (4116) J3___|25-00001-001 | Connector, 50 Pin Header Vertical 26-00001-016 | Socket DIP 16 Pin for U28 J6 — |25-00001-001 | Connector, 50 Pin Header Vertical U29 |15-10001-001 | RAM 16K x1 Dynamic (4116)
| J19 | |25-00002-002 | Connector, 2 Pin .156 Center | 26-00001-016 | Socket DIP 16 Pin for U29 |
| W1 | |25-00021-002 | Connector .1 Center for W1 | U30 |15-10001-001 | RAM 16K x1 Dynamic (4116) |
| W1 | |26-00007-001 | Shorting Pin | 26-00001-016 | Socket DIP 16 Pin for U30 |
| }32-00001-001 | |P.C.B. Video Processor Board | U31 |15-10001-001 | RAM 16K x1 Dynamic (4116) |
| U1 | |15-20245-001 | Bus Transiciever, Octal (74LS245) | 26-00001-016 | Socket DIP 16 Pin for U31 |
| U2 | |15-20245-001 | Bus Transiciever, Octal (74LS245) | U32 |15-10001-001 | RAM 16K x1 Dynamic (4116) |
| U3 | _|15-10003-001 | Ram 1K x 4 NMOS Static (2114) | 26-00001-016 | Socket DIP 16 Pin for U32 |
126-00001-018 |Socket DIP 18 Pin for U3 U33 | 15-10001-001 | RAM 16K x1 Dynamic (4116)
| U4 | |15-10003-001 | |Ram 1K x 4 NMOS Static (2114) | 26-00001-016 | Socket DIP 16 Pin for U33 |
26-00001-018 |Socket DIP 18 Pin for U4 U34 | 15-20374-001 | Latch, Octal (74L8374)
| US | [15-20157-001 | Multiplexer Quad 2-Input (74LS157) | U35 | 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) | |
| U6 | |15-20157-001 | Multiplexer Quad 2-Input (74LS157) | U36 | 15-20074-001 | Flip Flop Dual-D (74LS74) | |
| U7 | |15-20074-001 | |Flip Flop, Dual D (74LS74) | U37 |15-20008-001 | Quad, 2-Input and (74LS08) |
| U8 | |15-20032-001 | Quad 2 Input or (74LS32) | U38 | 15-70113-001 | Flip Flop JK Schottky (74LS113) | |
| U9 | |15-20032-001 | Quad 2 Input or (74LS32) | U39 | 15-20004-001 | Inverter, HEX (74LS04) |
U10 |15-10001-001 | RAM 16K x 1 Dynamic (4116) U40 | 15-30017-001 | Buffer/Driver, HEX (7417) 126-00001-016 | Socket DIP 16 Pin for U10 U41 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-016 | Socket DIP 16 Pin for U41
TAITO TAITO
| SYM | {PART NO. | DESCRIPTION | | | | SYM_|PART NO. | DESCRIPTION |
U42 | 15-10001-001 | RAM 76K x 1 Dynamic (4116) U81 _|15-20157-001 | Multiplexer Quad 2-Input (74LS157)
| 26-00001-016 | Socket DIP 16 Pin for U42 | U82 | |15-00002-001 | Microprocessor 68A09E |
U43 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) | 126-00001-040 | Socket DIP 40 Pin for U82 26-00001-016 | Socket DIP 16 Pin for U43 U83 |15-20244-007 | Octal, Buffer (74LS244)
| U44 } 15-10001-001 | RAM 16K x 1 Dynamic (4116) | ina fe | Octal, Buffer (74LS244) | |
| 26-00001-016 | Socket DIP 16 Pin for U44 | U85 | |15-10002-001 | {RAM 1K x 4 CMOS Static (6514) |
U45 | 15-10001-001 | RAM 76K x 1 Dynamic (4116) 126-00001-018 | Socket DIP 18 Pin for U85
| | | 26-00001-016 | Socket DIP 16 Pin for U45 | ug6_|15-10002-001 | RAM 1K x 4 CMOS Static (6514) |
| U46 | 15-10001-001 | Ram 16K x 1 Dynamic (4116) | |26-00001-018 | {Socket DIP 18 Pin for U86 |
26-00001-016 | Socket DIP 16 Pin for U46 U87 [15-20139-001 | Decoder Dual 1 of 4 (74LS139)
| U47 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) | use |15-20032-001 | Quad 2-Input of (74L832) | |
| | | 26-00001-016 | Socket DIP 16 Pin for U47 | | uag {15-20074-001 | Flip Flop, Dual-D (74LS74) |
U48 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U90 15-2000400" | inverter, HEX (74LS04)
| 26-00001-016 | Socket DIP 16 Pin for U48 | U91 | |15-20374-001 | Latch, Octal (74LS374) |
U49 | 15-20032-001 | Quad 2-Input or (74LS32) U92 |15-20374-001 | Latch, Octal (741S374) U50 | 15-20086-001 | Quad 2-Input Exclusive or (74LS86) U93_|15-20374-001 | Latch, Octal (74LS374) US51 | 15-20086-001 | Quad 2-Input Exclusive or (74LS86) U94 |15-20374-001 | Latch, Octal (74LS374)
| U52 | 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) | U95 |15-20299-001 | {Shift Register 8 Bit (74LS299) |
[Hs 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) | ug6 |15-20299-001 | Shift Register 8 Bit (74LS299) U54 | 15-20153-601 tee Dual 4-Input (7418153) U97 |15-20244-001 | Buffer, Octal (74LS244) U55 / 15-20157-001 | Multiplexer, Quad 2-Input (74LS157) U98 |15-20244-001 | Buffer, Octal (74LS244)
| U56 | 15-16008-001 | RAM 1K x 4 HMOS Static (2148) | | | U99 |15-20138-001 | Decoder, 1 of 8 (74L5138) |
26-00001-618 | Socket DIP 18 Pin for U56 U100}15-40000-001 | Quad 2-Input NOR (74C00) US7 | 15-10008-001 ‘| RAM 1K x 4 HMOS Static (2148) U101]15-20008-001 | Quad 2-input AND (74LS08) 26-09001-018 | Socket DIP 18 Pin for US7 U102|15-20010-001 | Triple 3-Input AND (74LS10) US58 | 15-30017-001 | Buffer/Driver, HEX (7417) U103}15-20000-001 | Quad 2-Input NAND (74LS00) ug /15-10001-001 | RAM 16K x 1 Dynamic (4116) U104) 15-20187-001 | Multiplexer Quad 2-Input (74LS157) U0 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U105}15-20299-001 | Shift Register 8 Bit (74LS299) U61 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U106|15-20299-001 | shift Register 8 Bit (74LS299) U62 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) [uo 15-20299-001 | Shift Register 8 Bit (74LS299) U63 | 15-19001-001 | RAM 16K x 1 Dynamic (4116) U108}15-20299-001 | Shift Register 8 Bit (74LS299)
| U64 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) | TESS | Shift Register 8 Bit (74LS299) |
| UBS | 15-10001-001 | RAM 16K x 1 Dynamic (4116) | 1 | U110]15-20299-001 | Shift Register 8 Bit (74LS299) |
U66 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U67 | 15-20032-001 | Quad 2-Input or (74LS32)
Us9 15-20244-001 Octal Buffer (74LS244) 15-20245-001 “[BUS Transciever, Octa! (7418248) U7 Ss 15-20374-001 Latch, Octai (74LS374) U7 15-20374-001 Latch, Octal (74LS374) u72 15-20374-001 Latch, Octal (74LS374) U73 15-20157-001 Multiplexer Quad 2-input (74LS157) u74 15-20157-001 Multiplexer Quad 2-Input (74L$157) U75 15-20245-007 BUS Transciever, Octal (74LS245) | u76 [15-20273-001 Register 8 Bit (74LS273) U77 |15-20373-001 Latch, Octal (74LS373) U78 | 15-20373-001 | Latch, Octal (741373) U79 | 15-20373-001 Latch, Octal (74L8373) [uso [15-20373-001 Latch, Octal (7415373)
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
DATA/SOUND PROCESSOR
| TATO | |, | [rato | | |
| SYM | PART NO. | DESCRIPTION | SYM | PART NO. | DESCRIPTION |
Ri {| 11-00001-473 | Resistor 47K %4W +5% [FB5 | 17-00001-001 | Ferrite Bead
| R2 | 110000882 [Resistor 3.3K VW +5% | FB8_ | }17-00001-001 | Ferrite Bead |
| R3_| | 11-00001-332 | Resistor 3.3K %4W +5% | FB9 | 17-00001-001 | Ferrite Bead |
R4 | 11-00001-332 | Resistor 3300 OHM YW +5% FB10 | 17-00001-001 | Ferrite Bead RS _| 11-00001-472 | Resistor 4.7K %4W +5% FB11 | 17-00901-007 | Ferrite Bead R6 | 11-00001-103 | Resistor 4.7K %4W +5% FB13 | 17-00001-001 { Ferrite Bead
| R7 | 11-00001-103 | Resistor 10K 4W +5% | Ee | 17-00001-001 | Ferrite Bead |
RB __| 11-00001-332 | Resistor 3.3K OHM 4W =5% FB15 | 17-00001-001 | Ferrite Bead
| RQ _| 11-60001-502 | Pot, P.C. Mount 5K | | | FB16 |17-00001-001 | Ferrite Bead |
Ri0 | 11-00001-473 | Resistor 47K VW +5% [817 17-00001-001 | Ferrite Bead R11 | 11-00001-473 [Resistor ATK YaW 5% FBt8 | 17-00001-001 | Ferrite Bead
| R12_| | 11-00001-332 | Resistor 3.3K 4W +5% | FB19 | 17-00001-001 | Ferrite Bead | ||
| R13_| | 11-00001-332 | Resistor 3.3K 44W «5% | | | | F820 | 17-06001-001 | Ferrite Bead | _| |
| R14 | 11-00001-332 | Resistor 3.3K %W +5% | Ci | | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead | ||
| Rt5 | 11-00001-332 | Resistor 3.3K 4W +5% | C2 | {12-10002-104 | Capacitor Ceramic .tuf 50V Axial Lead | ||
| (R16 | 11-00001-332 | Resistor 3.3K %4W +5% | 1 | 03 “[r2-70002-104 | Capacitor Ceramic .1uf 50V Axiai Lead |
R17 | 11-00001-332 | Resistor 3300 OHM %4W +5% C4 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R18 | 11-00001-124 “| Resistor 120K YW +5% C5 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead
| R19 | 11-00001-472 | Resistor 4.7K %4W +5% | _| | C6 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead |
| R20 | 11-00001-221 | Resistor 220 OHM V4W +5% | C7 | —112-20001-107 | Capacitor Electrolytic 100uf 16V |
[R21 | 11-00001-221 | Resistor 220 OHM WW +5% C8 = | 12-20001-107 | Capacitor Electrolytic 100uf 16V R22 | 11-00001-332 | Resistor 3.3K %4W +5% C9 | 12-20001-107 } Capacitor Electrolytic 100uf 16V
| R24 | 11-00001-182 | Resistor 1.8K %W +5% | C10 _[12-20001-107 | Capacitor Electrolytic 100uf 16V | |
| R25_| | 11-60001-104 | POT, P.C. Mount 100K | C11 | 12-20001-107 | Capacitor Electrolytic 100uf 16V | |
| R26 | 11-00001-103 | Resistor 10K %4W +5% | C12 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead | | | |
| R27 | 11-000G1-103 | {Resistor 10K 4W +5% | fora | 12-10002-164 | Capacitor Ceramic .1uf 50V Axia! Lead |
| R28 | 11-00001-223 [Resistor 22K VW = 5% C14 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R29 | 11-00001-562 | Resistor 5.6K 4W +5% C15 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R30 | 11-00001-332 | Resistor 3.3K YW 5% C16 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R3t_ | 11-00001-020 | Resistor 2.2 OHM v4W +5% C17_|12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead
| id | BE | Resistor 1 OHM YaW +5% | C18 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead |
| R33_| | 11-00001-020 | Resistor | 2.2 OHM 44W +5% | Ci9 | 12-10003-470 | Capacitor 47pf 10% NPO Axia! Lead |
| R34_| | 11-00001-010 | Resistor 1 OHM YeW +5% | C20 | 12-20001-105 | Capacitor Electrolytic 1uf |
R35 |} 11-00001-102 | Resistor 1.0K OHM %W +5% C21 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead
| R36 | 11-00001-332 | Resistor 3.3K %4W +5% | | | €22 | 12-20001-807 | Capacitor Electrolytic 800uf, 16V |
| R37_| | 11-00001-152 | Resistor 1.5K %4W +5% | €23 | 12-20001-807 | Capacitor Electrolytic 800uf, 16V |
| R38_| | 11-00001-222 | Resistor 2.2K %4W +5% | C24 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead |
| R39_| | 11-00001-221 | Resistor 220 OHM V4W +5% | €25 | 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead |
| R40 _ | 11-00001-332 | Resistor 3.3K 4W +5% | 26 | [12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial = |
| | R41 | [11-00001-562 | Resistor 5.6K YW --5% | €27 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead |
R42 | 11-00001-223 | Resistor 22K 4W +5% C28 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R43 | 11-00001-103 | Resistor 10K YW +5% |c20_| 42-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead,
| R44 | 11-00001-103 | Resistor 10K 4W +5% | €31_} | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead |
| R45 | 11-00001-103 | Resistor 10K %4W +5% | | | C32 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead |
| R50 | 11-00001-472 | Resistor 4.7K %“4W +5% | {ca3_|12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead |
| FB4 a 17-00001-001 | Ferrite Bead C34 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead FB2 | 17-00001-001 | Ferrite Bead C35 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead FB3 | 17-60001-001 | Ferrite Bead C36 | 12-10002-104 { Capacitor Ceramic .1uf 50V Axial Lead FB4 | 17-00001-001 [Ferrite Bead
DATA/SOUND PROCESSOR
| Tao | TaITO | la | |
| SYM | PART NO. | DESCRIPTION | SYM | PART NO. | DESCRIPTION |
| C37_| | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead | TP3 | 59-00021-001 | Test Point |
C38 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead TP4 | 59-00021-001 | Test Point C39 | 12-10001-123 | Capacitor Ceramic .012 50V Axial Lead TP5 | 59-00021-001 | Test Point C40 | 12-10001-183 | Capacitor Ceramic .018 SOV Axial Lead TP6 | 59-00021-001 | Test Point C41 | 12-10004-103 | Capacitor Ceramic .O1uf SOV Axial Lead TP7 | 59-00021-001 | Test Point €42 | 12-10001-332 | Capacitor Ceramic .0033uf 50V Axial Lead TP8 | 59-00021-001 | Test Point C43 | 12-10001-153 | Capacitor Ceramic .015uf 50V Axial Lead TPQ | 59-00021-001 | Test Point C44 | 12-10001-563 | Capacitor Ceramic .056uf 50V Axial Lead TP10 | 59-00021-001 | Test Point C45 | 12-10003-100 | Capacitor 10pf NPO Axial Lead TP11 | 59-00021-001 | Test Point C46 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead RP1 | 11-50001-332 | Resistor Sip Pack 3.3K C47 | 12-20001-105 | Capacitor Electrolytic 1uf Axial Lead RP2 | 11-50001-332 | Resistor Sip Pack 3.3K C48 | 12-20001-105 | Capacitor Electrolytic 1uf Axial Lead RP3 | 11-50001-471 | Resistor Sip Pack 47K
| C49 | 12-10001-471 | Capacitor Ceramic 470uf 50V Axiai Lead | | RP4 | 11-50001-471 | Resistor Sip Pack 47K |
C50 | 12-10001-471 | Capacitor Ceramic 470pt 50V Axial Lead RPS | 11-50001-103 | Resistor Sip Pack 10K C51 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead RP6 | 11-50001-332 | Resistor Sip Pack 3.3K C52 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead U1 | 15-20244-001 | Octal Buffer (74LS244) C53 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U2 | 15-00002-001 | Microprocessor 68A09E C54 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 26-00001-040 | Socket 40P DIP-For 68AO9E C55 _| 12-20001-105 | Capacitor Electrolytic uf U3 | 15-20244-001 | Octal Buffer (74LS244) C56 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U4 = | 15-20244-007 | Octal Buffer (74LS244) C57 | 12-20001-477 | Capacitor Electrolytic 470uf, 16V US | 15-00007-001 | Microprocessor 6802
| C58 | 12-20001-477 | Capacitor Electrolytic 470uf, 16V | 26-00001-040 | Socket 40P DIP for 6802 |
C59 | 12-10002-104 4 | Capacitor Ceramic .1uf 50V Axial Lead U6 | 15-20244-001 | Octal Buffer (74LS244) C60 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead U7 | 15-00004-002 | Parallel 1/0 6821 (61 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U8 | 15-00004-002 | Parallel 1/0 6821 C62 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U9 | 15-20245-001 | BUS Tranciever, Octal (74LS245)
- | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U10 | 15-20244-001 | Octal Buffer (74LS244) C64 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U11 | 15-20245-001 | BUS Tranciever, Octal (74LS245) C65 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U12 | 15-20244-001 | Octal Buffer (74LS244) C66 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U13 | 15-50001-001 | Digital to Analog Converter 8 Bit (1408) C67 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead| U14 | 15-20032-001 | Quad 2-Input or (74LS32) (68 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U15 | 15-10003-001 | RAM 1K x 4 NMOS Static (2114)
| [cea | 12-10002-104 | Capacitor Ceramic .tuf 50V Axial Lead | 26-00001-018 | Socket 18P DIP for 2174 |
C70 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U16 | 15-10003-001 | RAM 1K x 4 NMOS Static (2114)
| [ort | 42-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead | 26-00001-018 | Socket 18P DIP for 2114 |
C72 | 42-10003-101 | Capacitor 100pf 10% NPO Axial Lead U17 | 15-20138-001 | Decoder 1 of 8 (74LS138) €73 | 12-10003-221 | Capacitor 220pf 10% NPO Axial Lead U18 | 15-50003-001 | Quad OP AMP LM324 C74 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead U19 | 15-60004-001 | Speech Synthesis TMS5200 C75 | 12-20001-105 | Capacitor Electrolytic 1uf 26-00001-028 | Socket 26P DIP for TMS5200 C76 | 12-20001-105 | Capacitor Electrolytic tut U20 | 15-00004-001 | Parallel 1/0 68A21 C77 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U21_ | 15-60002-001 | Line Driver (MC1488) C78 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U22 | 15-00005-002 | Serial 1/0 68A50 C79 | 12-10002-104 } Capacitor Ceramic .1uf 50V Axial Lead 26-00001-024 | Socket 24P DIP for 68A50 C80 | 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead U23 | 15-20004-007 | Inverter, HEX (74LS04) C81 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U24 | 15-44066-001 | Quad Analog Multiplexer (4066)
| C83 | |12-10003-100 | Capacitor 10pf NPO Axial Lead | U25 | 15-60001-001 | Line Receiver (MC1489) |
| TP1 | |59-00021-001 | Test Point | U26 | 15-20161-001 | Counter 4-Bit Presettable (74LS161) |
| TP2 | |59-00021-001 | Test Point | U27 | 15-20092-001 | Counter Divide By Twelve (74LS92) |
U28 | 15-44066-001 | Quad Analog Multiplexer (4066)
DATA/SOUND PROCESSOR
TAITO SYM | PART NO. DESCRIPTION U29 | 15-50002-001 | Audio Amplifier (2002) 30-00001-001 | Heatsink to 220 U30_| 15-50002-001 | Audio Amplifier (2002) | 30-00001-001 | Heatsink to 220 SW1 | 29-00001-001 | Switch, DIP 4 Pole Yt | 19-00002-001 | Crystal 7.3728 MHZ Q1 | 14-23904-001 | Transistor NPN, Silcon 2N3904 J1 | 25-60002-004 | Connector 14 PIN Locking J5 | 25-00001-001 | Connector Header 50 PIN J6 | 25-00001-001 | Connector Header 50 PIN | J7 | 25-00002-005 | Connector 5 PIN Locking J8 | 25-00002-005 | Connector 5 PIN Locking J9 | 25-00003-001 | Connector RS232
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ROM/V/0 P.C. ASSEMBLY
TAITO TAITO
| SYM | PART NO. | DESCRIPTION | SYM; PART NO. | DESCRIPTION |
| Ri | 11-00001-562 | Resistor 5.6K, %4W +5% | R51; | 11-00001-471 | |Resistor 470 OHM %W +5% |
| R2_| | 11-00001-471 | Resistor 470 OHM Y4W +5% | Rs2 | 11-00001-562 Resistor 5.6K, %4W +5% | |
| R3__| | 11-00001-471 | Resistor 470 OHM YW +5% | R53 | 11-00007-562 | Resistor 5.6K, 4W +5% |
R4 | 11-00001-471 | Resistor 470 OHM 14W +5% R54 | 11-00001-471 | Resistor 470 OHM %W +5% RS | 11-00001-471 | Resistor 470 OHM %W +5% R55 | 11-00001-471 | Resistor 470 OHM %4W +5%
| R6__| | 11-00001-471 | Resistor 470 OHM %4W +5% | R56 | 71-00001-471 | /Resistor 470 OHM YW +5% |
| R7__| | 11-00001-471 | Resistor 470 OHM %4W +5% | R57 | 11-00001-477 | |Resistor 470 OHM YW =5% |
| R8__| | 11-00001-471 | Resistor 470 OHM %4W +5% | R58 | 11-00001-471 | |Resistor 470 OHM %4W +5% |
| RQ | 11-00001-471 | Resistor 470 OHM 4W +5% | R59 | 11-00001-471 | {Resistor 470 OHM VaW +5% | |
| R10 | 11-00001-471 | Resistor 470 OHM %4W +5% | R60 | 11-00001-471 | Resistor 470 OHM 14W +5% | |
| R11 | 11-00001-471 | Resistor 470 OHM %4W +5% | R61 | 11-00001-471 | |Resistor 470 OHM %4W +5% | |
| |R12_| | 11-00001-471 | Resistor 470 OHM %4W +5% | R62 | 11-00001-471 | {Resistor 470 OHM YW +5% |
| R13} | 11-00001-471 | Resistor 470 OHM %W +5% | R63 | 11-00001-471 | |Resistor 476 OHM YW +5% |
R14 | 11-00001-471 | Resistor 470 OHM %4W +5% C1 | 12-10002-104 |Capacitor Ceramic .1uf Axial Lead R15 | 11-00001-471 | Resistor 470 OHM %4W +5% C2 | 12-10002-104 |Capacitor Ceramic .1uf Axial Lead
| R16 | 11-00001-471 | Resistor 470 OHM %4W +5% | C3} | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
| R17 | 11-00001-471 Resistor 470 OHM YW +5% | C4 =| 12-10001-471 | Capacitor Ceramic 470pf Axial Lead |
R18 | 11-00001-471 | Resistor 470 OHM %4W +5% C5 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| R19 | 11-00001-471 | Resistor 470 OHM %4W +5% | C6 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| R20_| | 11-00007-562 | Resistor 5.6K, %4W +5% | | | C7 __| 12-10001-471 | Capacitor Ceramic 470pf Axial Lead |
| R21 | 11-00001-562 | Resistor 5.6K, %W +5% | C8 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| R22_| | 11-00001-562 | Resistor 5.6K, 4W +5% | C9 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
| R23 | 11-00001-562 | Resistor 5.6K, ¥4W +5% | C10 } 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| R24 | 11-00001-562 | Resistor 5.6K, ¥4W +5% | C11_| | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
| R25_| | 11-00001-562 | Resistor 5.6K, 4W +5% | C12 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
| R26 | 11-00001-562 | Resistor 5.6K, 4W +5% | C13 | 12-10001-471 | {Capacitor Ceramic 470pf Axial Lead | |
| R27 | 11-00001-562 | Resistor 5.6K, 4W +5% | C15 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| R28 | 11-00001-471 | Resistor 470 OHM “MW +:5% | C16 | 12-10001-471 | |Rapacitor Ceramic 470pf Axial Lead | |
| R29 | 11-00001-471 | Resistor 470 OHM %W +5% | C17 | 12-10001-471 | }Capacitor Ceramic 470pf Axial Lead | |
| R30 | 11-00001-471 | Resistor 470 OHM YW +5% | C18 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| R31_| | 11-00001-471 | Resistor 470 OHM %4W +5% | Ci9 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | |
| R32_| | 11-00001-471 | Resistor 470 OHM Y4W +5% | C20 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
| R33_| | 11-00001-471 | Resistor 470 OHM /4W +5% | C21 | 12-16001-471 | Capacitor Ceramic 470pf Axial Lead |
R34_ | 17-00001-471 | Resistor 470 OHM YaW +5% C22 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| R35 | 11-00001-471 | |Resistor 470 OHM YW =5% | C23 | 12-10001-471 | {Capacitor Ceramic 470pf Axial Lead |
| R36 | 11-00001-471 | Resistor 470 OHM YW +5% | C24 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead | |
| R37_ | 11-00001-471 | Resistor 470 OHM YW =5% | C25 | 12-10001-471 | {Capacitor Ceramic 470pf Axial Lead |
R38_ | 11-00001-471 | Resistor 470 OHM %4W +5% C26 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R39 | 11-00001-471 | Resistor 470 OHM t4W +5% C27 | 12-10002-104 |Capacitor Ceramic .1uf Axial Lead
| R40 | 11-00001-562 | Resistor 5.6K, 4W +5% | C28 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead |
| R41 | 11-00001-562 |Resistor 5.6K, %4W +5% | C29 | }12-10002-104 |Capacitor Ceramic .1uf Axial Lead |
R42 | 11-00001-562 | Resistor 5.6K, 4W +5% 30 | 12-10002-104 |Capacitor Ceramic .tuf Axial Lead
| R43 | 11-00001-562 | |Resistor 5.6K, 44W +5% | C31 | 12-10002-104 |Capacitor Ceramic .1uf Axial Lead |
R44 | 11-00001-471 | Resistor 470 OHM %4W +5% C32 | 12-10002-104 |Capacitor Ceramic .tuf Axial Lead
| R45 | 11-00001-471 | [Resistor 470 OHM Y4W +5% | C33 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead |
| R46 | 711-00001-471 | [Resistor 470 OHM YaW +5% | C34 | 12-10002-104 |Capacitor Ceramic .1uf Axial Lead |
| R47 | |11-00001-471 | Resistor 470 OHM %4W +5% | C35 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead |
| R49 | 11-00001-471 | |Resistor 470 OHM YW +5% | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead |
11-00001-471 | Resistor 470 OHM YW +5% | |s [R50
ROM/V/0 P.C. ASSEMBLY
TAITO TAITO
| SYM | PART NO. | DESCRIPTION | SYM | PART NO. | DESCRIPTION |
| C37 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | C85 | 12-10001-471 | |Capacitor Ceramic 470pf Axial Lead |
C38 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C86 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C39 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C87 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C40 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C88 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C41 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 89 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C42 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C90 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 43 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C91 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C44 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C92 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
| C45 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB1 | 17-00001-001 | |Ferrite Bead |
| C46 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB2 | 17-00001-001 | |Ferrite Bead |
| C47 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB3 | 17-00001-001 | |Ferrite Bead |
| C48 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB4 | 17-00001-001 | |Ferrite Bead |
| C49 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB5 | 17-00001-001 | |Ferrite Bead |
| C50 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB6 | 17-00001-001 | {Ferrite Bead |
C51 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB7 | 17-00001-001 | Ferrite Bead C52 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB8_|17-00001-001 | Ferrite Bead C53 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB9 | 17-00001-001 | Ferrite Bead C54 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB10 | 17-00001-001 | Ferrite Bead C55 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB11 | 17-00001-001 | Ferrite Bead C56 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB12 | 17-00001-001 | Ferrite Bead C57 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB13 | 17-00001-001 | Ferrite Bead C58 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB14 | 17-00001-001 | Ferrite Bead C59 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB15 | 17-00001-001 | Ferrite Bead 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB16 | 17-00001-001 | Ferrite Bead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB17 | 17-00001-001 | Ferrite Bead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB18 | 17-00001-001 [Ferrite Bead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB19 | 17-00001-001 | Ferrite Bead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB20 | 17-00001-001 | Ferrite Bead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB21 | 17-00001-001 | Ferrite Bead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB23 | 17-00001-001 | Ferrite Bead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB24 | 17-00001-001 | Ferrite Bead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB25 | 17-00001-001 {Ferrite Bead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB26 | 17-00001-001 | Ferrite Bead C70 | 12-20001-107 | Capacitor Electrolytic 100uf FB27 |17-00001-001 | Ferrite Bead C71 | 12-10001-471 | Capicitor Ceramic 470pf Axial Lead FB28 | 17-00001-001 | Ferrite Bead C72 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB29 | 17-00001-001 | Ferrite Bead C73 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB30 | 17-00001-001 | Ferrite Bead C74 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB31 | 17-00001-001 | Ferrite Bead C75 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB32 | 17-00001-001 | Ferrite Bead C76 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB33 | 17-00001-001 | Ferrite Bead C77 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB34 | 17-00001-001 | Ferrite Bead C78 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB35 | 17-00001-001 | Ferrite Bead C79 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB36 | 17-00001-001 | Ferrite Bead C80 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB37 | 17-00001-001 | Ferrite Bead C81 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB38 | 17-00001-001 | Ferrite Bead C82 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB39 | 17-00001-001 | Ferrite Bead C83 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB40 | 17-00001-001 | Ferrite Bead
| C84 { 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB41 | 17-00001-001 | |Ferrite Bead |
ROM/V/0 P.C. ASSEMBLY
TAITO TAITO
| SYM | PART NO. | DESCRIPTION | SYM | PART NO. | DESCRIPTION |
| FB42 | 17-00001-001 | Ferrite Bead | U6 | E-PROM “‘aix”™ |
[FB43 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U6
| FB44 | 17-00001-001 | Ferrite Bead | U7 | E-PROM “QIx”™ |
FB45 |17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U7
| FB46 | 17-00001-001 | Ferrite Bead | U8 | E-PROM “QIx”™ |
FB47 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U8
| FB48 | 17-00001-001 | Ferrite Bead | ug | E-PROM “‘QIx”™ |
FB49 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U9
| FB5O | 17-00001-001 | Ferrite Bead | U10 | E-PROM “QIx"™ |
FBS1 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U10 FB52 | 17-00001-001 | Ferrite Bead U11 | 15-00004-001 | Paralelt 1/0 68421
| FB53 | 17-00001-001 | Ferrite Bead | U12 | E-PROM “QIX"™ |
| Di | | 13-14001-001 | Diode 1N4001 | 26-00001-024 |Socket 24 Pin Dip for U12 |
| D2 | 13-14001-001 | Diode IN4001 | U13 | E-PROM “‘Q)x"™ |
D3 _| 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U13
| D4 | 13-14001-001 | Diode IN4001 | U14 | E-PROM “QIX”™ |
D5 | 13-14001-001 | Diode IN4001 26-00001-024 |Socket 24 Pin Dip for U14
| D6 _| 13-14001-001 | Diode IN4001 | U15 | E-PROM ‘QIxX"™ |
| D7 | _|13-14001-001 | Diode IN4001 | '26-00001-024 | Socket 24P Dip Used For E-PROM |
| D8 | 13-14001-001 | Diode IN4001 | U16 | E-PROM “‘QiX''"™ |
D9 =| 13-14001-001 | Diode IN4001 26-00001-024 |Socket 24 Pin Dip for U16
| D10 | 13-14001-001 | Diode IN4001 | U17 | E-PROM “‘Qix’™ |
| D11_ | {13-14001-001 |} Diode 1N4001 | 26-00001-024 | Socket 24 Pin Dip for U17 |
| D12 | 13-14001-001 | Diode IN4001 | U18 | E-PROM “‘QIX”™ |
Q1 | 14-00001-001 | Transistor NPN Darlington TIP120 26-00001-024 |Socket 24 Pin Dip for U18
| Q2 | 14-00001-001 | Transistor NPN Darlington TIP120 | U19 | E-PROM “QiX"™ |
Q3 | 14-00001-001 | Transistor NPN Darlington TIP120 | 26-00001-024 |Socket 24 Pin Dip for U19
| Q4 | 14-00001-001 | Transistor NPN Darlington TIP120 | U20 | }15-00004-001 | Paralell 1/0 68A21 |
| Q5 | 14-00001-001 | Transistor NPN Darlington TIP120 | U21 | |15-20138-001 | Decoder 1 of 8 (138) |
| Q6 | 14-00001-001 | Transistor NPN Darlington TIP120 | |U22 | |26-00002-016 | ROM Select |
Q7 | 14-00001-001 | Transistor NPN Darlington TIP120 26-00001-014 |Socket 24P Dip for U22
| Q8 | 14-00001-001 | Transistar NPN Darlington TiP120 | U23_|15-20004-001 | Inverter, HEX (74LS04) | |
| ag | Not Used | U24 | Not Used |
| Q10 | 14-00001-001 | Transistor NPN Darlington TIP120 | U25 | Not Used | |
| Q11_ | 14-00001-001 | Transistor NPN Darlington TIP120 | 26 | Not Used | |
| Q12 | 14-00001-001 | Transistor NPN Darlington TIP120 | U27 | E-PROM “QIX”™ |
U1 | 26-00002-016 | ROM Select 26-00001-014 |Socket 14P Dip for U27 26-00001-014 | Socket 14P Dip, for U1 U28 | 15-20138-001 | Decoder 1 of 8 (138)
| U2 | _{15-20138-001 | Decoder 1 of 8 (138) | U29 | ROM Select |
| U3 | E-PROM “alx’™ | 26-00001-014 | Socket 14P Dip Used For ROM Select |
26-00001-024 | Socket 24 Pin Dip for U3 U30_|15-00004-007 | Paralell 1/0 6821
| U4 | | | E-PROM “‘QIX"™ | v3 | |25-00001-001 | Connector Header SOPIN |
}26-00001-024 | Socket 24 Pin Dip for U4 J5—_{25-00001-001 | Connector Header SOPIN
| US | E-PROM “‘QIX"'"™ | J6 | —_|25-00001-001 | Connector Header 50PIN |
| /26-00001-024 | Socket 24 Pin Dip for US | Ju Fer oone-te | Connector 14 Pin Header .156 Center |
J15 _|25-00002-014 | Connector 14 Pin Header .156 Center J16 |25-00002-014 {Connector 14 Pin Header .156 Center J17_|25-00002-014 | Connector 14 Pin Header .156 Center
COIN. DOOR CONTROL, PANEL
(UPS 67890 NR
em ore VIDEO PROCESSOR "iS . : RSE. mova Jao qf TE Afi re scone next (a0 me)
08-00001-001 aes
Uh T i ole mM lente
y aH
PRIMARY. BRACKET
fs ee ct a ROM/TIO PCB 08-00003-001a4 _[msyRuETON Hee aaa
viguts WAROUEE “tients Uff some
VIBOLAIOA FOR 120V LINE V275LAISA FOR 240V LINE pope VOLTAGE, PROGRAMMING \ JUMPER
Loe ! \
Le
7 ( sase | _S>\x0r 1 \ av Ey | une 2 / FILTER |_[ 3 NEUTRAL LL —=8
L =-——- }+——AINE Corp/FILTER ASSY [+-—— primary BRACKET y20vAc POWER SUPPLY SCHEMATIC
poxae SECONDARY BRACKET
R37 100K.
Rs, 22K NOTICE TO A\L PERSONS RECEIVING THIS DRAWING SS
Ja=i4) RST GND GND Je-1 So ee mse +
t ING276 5S Ri 152 4W Je-3 et (J2-4_)=™ Ri2 5.2 4W
3-1 +5 RIT. AA 2.2K
|_ Gees —Cose +128 +} J2-5 So 2N3055 i
i !
L J3-2_)*5 |
I
I
I
i
uw FLED 2 CEA CUE en WB=1O )+12¢ HEAT SINK ASSY
R34 12K al Et iep3 4$— C48 )-12 J3-4_)-5
Key (J4-3) key (93-9)
TAITO AMERIGA CORPORATION.
VIDEQ PROCESSOR SCHEMATIC 1 OF 2
VAIO H 12131415, T RP4
uls
ort i} USI ] iW 8 ei CONTR Z_ OAT,
E6 25) +OCJ6 = 11) [q ph at ati es &
ADR=9403H Tee MHZ NOTICE TO ALL PERSONS RECEIVING THIS ORAWING. en, abn witha jhe
‘an design or techn na ay ght to egrocuce Ts thereol. Except tor manutacture By ve or neat er teres the Seba Sh ret ces by wren
ert Pesoon ee ES
Gat VIDEO PROCESSOR
[=| Ea P+ ep" " TEP R0G00 U4
VIDEO PROCESSOR SCHEMATIC 2 OF 2
+5 + 412V ‘ aa f < $y IM
{ee 4 FRA YY FBS = FBG YY) f ) er cus J-le. Se. FERRITE BEADSWO)
Wore To Al Panaone arceTra Tie ORAWwG CONFIDENTIAL : Reproduction forbicton without the issn ot Taito America Corp. Eke lon condi
Om]
DEES SST od pr
VIDEO PROCESSOR
DATA/SOUND PROCESSOR SCHEMATIC
+
Ne
1OOMFS)
Mus Py
SVTE-DOR PATLQ___9 a7 I3)s Y) ON | 90008) Ta RE b Y | A-CNT | | 156 if | 9001H | 4 DANY pe 68421 | | iad OUND ADDRESS BUS 77“ | 3x U20 SOUND Cl ‘F10 SOUND DATA BUS Z J Da ADRESS DATA DATA BUS 2 DATA CONTROL BUS TP3
TAITO AMERICA CORPORATION
, COIN DOCR (— 2 Tio CKTS ut ROM 1/0 SCHEMATIC
—— £54
| l | LER: | L |
: isa f PS 10) wi5] 7 IPAQ. 6 Z| 14 Stee pag [+-—4 Cis” SPR 1 PE By
| 9 | N/C KEY | tbat | 4 |
C10. M AP Zleso
- ty DATA PROGRAM, r
| 9 | furl | Jus] | joel |
| uig| | od | 14 | hua lt |
farapararararar EPEVEVEIEVE EVE E(e/B/a) 5/6) 5] § aba abe kab §/5)5 (5/5/83 /518 SIS TESS 8/818 EE 82/8 /8]s | eye 18 19/18 rr Uu2l |
~ 4 T ; ses om) 144 39_ OF lB I 7) lus | 4 ushis Tune a) alealala/el-]-] - 12 aa 7 xrjztjr}zrl| zr) xz{ zr BLES) E/E IS 18/6 a/s)aalalslala 8/8/8/8\8]s/si18
- 2/8) 2/8/8/8)8 ws Ee ejeleie ey evs ye ys ol im
ro +ppme 1g _) [6
cD) Je=4) VIDEO PROGRAM
[68820 | 6821 EMORY MAP “T 3 NORE NOT Oe ae | ult 9400H| 9401} 9402H | 9403H 20 9900H | 9901 H| 9902H) 9903H U30 Ll COOH | 9CO!H| SCOZH|) 3CO3H
NOTICE TO ALL PERGONS RECEIVING THIS DRAWNIG CONFIDENTIA: : Reproduction frtiddon ylnout the cle went co Amanen Corp. Em
Pf REVISIONS | CED) o SPARE. :
| * | - | arorr | (2 |
tov ee L 02-7)
| us | usp | Da | 3 |
23] 7
| a | |U26) lis | | mn |
t}2lchs D4 D le Els 3 aie] 5 a oe he z_)
| 18 =| a Ho | L | 19 |
| a | 8)elo. | ri |
AAS 15 | § oe ce sat S| =| be F 3eLaces ieyeye + Jee - FF HD ppeSet Cae
>" FERRITE BEADS)
_PCWER/GROUND TABLE
| Ic. | GNI | +12) | |
ie ele LLS15S 6 a
tp oe Te Te6cco03 Te)
WARRANTY
TAITO AMERICA CORPORATION warrants that its printed circuit boards and parts are free from defects in material and workmanship under nomal use and service for a period of ninety (90) days from the date of shipment. Seller warrants that its monitors are free from defects in material and workmanship under normal use for a period of thirty (30) days from the date of shipment. The factory also warrants all socketed parts for a period of ninety (90) days when furnished with the game serial number. If the above products fail to conform to this Warranty Taito America Corporation has the option to repair, replace, or credit the Buyer’s account. The Buyer must notify Taito America Corporation in writing upon finding the defective product. Buyer must also return the defective product prepaid to Taito America Corporation’s factory located in Elk Grove Village, Illinois. If Taito America Corporation determines upon examining the returned product that damage was caused by accident, misuse, neglect, modification, or improper repair or testing, this Warranty will be void. |n no event will Taito America Corporation be held for loss of profits to Buyer.
\rartoJ ® TAITO AMERICA CORPORATION 1256 Estes Avenue, Elk Grove Village, |L 60007 Telephone (312) 981-1000 Telex 25-3290