CATHODE RAY TOMES

Centipede DP-182-1st-02A

Centipede (revision 4) (Atari, 1980) · Drawing Package · 1 pages · original scan

Page 1
Scan of page 1

Centipede Playfield RAM Testing the Playfield RAM

11, Perform the CAT Box™ preliminary setup. 3.

  • Set the CAT Box switches as follows: Press TESTER RESET DBUS SOURCE TO ADDR BYTES to 1024 4 RAW MODE to (OFF) RIW to WRITE Key in 0400

‘Togale RW MODE to SINGLE

to Togale rrereacgp From Meu Assess Bus. shoot 1 Sie B

HE

= lacs = ‘From Sync aa —~ Coneator sheet Side 8

Playfield Address Selector

‘The Playtield Address Selector controls the access tothe playfield memory.

Itallows elther the game MPU or the sync generator to scan the playfield mem: When 3 on pin 1 of PS and P7 is low and pin 18 on P7 Is low, the Playfield

ony. Tho Payot Adres Selector consis of multiplexers PS, and P7 and gate Ké,

‘Address Selector receives BH, 16H, 32H, and 64H on PS and 16V,32V, 64V, and ‘28V on P7 from the sync generator. These signals enable the sync generator circuits to access the playfield memory.

When 3H goes high the game MPU addresses the playfield memory (via ‘ABO-AB9) for the positioning ofthe graphics. During horizontal blanking (pin 15. ‘of P7 is high) the outputs of P7 (PFAS.PFA7) are held high enabling the motion ‘object circuitry to access the playfield memory for the motion objects to be displayed.

AL ATARI

Sheet 2, Side A

Centipede”

Playfield Memory Playfield Multiplexer Picture Data ROM Circuitry Motion Object Circuitry (Vertical) Motion Object Circuitry (Horizontal)

Section of 03724101 B

1961 Ata, ne

‘Sheet 2, Side Delteaba fat printing entipese It te CAT Box reads an address that doesn't compare, the COM: PARE ERROR LED lights, the ADDRESSISIGNATURE display shows the failing address location, and the ERROR DATA DIS- PLAY switch is enabled.

W the COMPARE ERROR LED does not light, rokey 0400 and repeat the test with the DBUS SOURCE switch set to ADDR. This, fneures that the data bits at address 0400 will go high. if the COMPARE ERROR LED does not light after this step, the Play: field RAM is good

picture data PROM circuitry. Playfield Multiplexer

The Playfield Multiplexer receives playfield data from the playtield memory (PFDO-PFO31) and the output (PFO-PF7) is a code that determines what is 1) dis- ‘Generator played on the monitor, or 2) ead or updated by the MPU. The Playfield Multiplexer Consists of select multiplexers KE, L6, M6, N6 and PS.

When 256H is low and 4H is high, AB4 and ABS from the MPU address bus is the ‘selected output from PS. This output is applied to multiplexers KE, L6, M6, and NE {5 select inputs. When the MPU is accessing the playfield code muitiplexer, the playfield datais either being read or updated by the MPU. When 256H is high and 4H rator(128H and 8V) are the selected outputs. ‘These signals then select which bits of data PFOO-PFD31 are sent out via KB, LE, M6, and N6 for the playfield codes that eventually are displayed on the monitor. Is low, the inputs from the syne ge

‘The playlield codes (PFO-PF7) are latched by J6 and J6 to the MPU data bus (5) ‘and to the picture data PROM circuitry (6). When PFRARD is low and 1H from the Syne generator goes high, the Inputs on J5 (PFO-PF7) are latched out to the MPU via (DBO.DB7. When 4H on pin 11 of J goes high, the inputs (PFO-PF7) are latched to the From Syne | ee Sheet 1, Side B

From Syne Generator Sheet 1, Side 8 Motion Object Circuitry (Vertical)

‘The Motion Object Circuitry (vertical) receives playfield data and vertical inputs from the syne generator circuitry to generate the vertical component of the motion object video. PFO8- 4 Irom the playfield memory and 1V-128V from the sync generator are compared at F6 and H6. ‘The output is gated by A7 when a motion object is on one of the sixteen vertical lines and is, latched by E6 to AND gate B7. A low on B7 pin 8 indicates the presence of a motion object on ‘one of the vertical lines during non-active video time. This signal (MATCH) enables the mult plexers in the picture data circuitry

When 256H on pin 1 of 07 goes high, 1V,2V, 4V and PICO are selected. When 256H goes low, the latched output of E6 is selected. The output of D7 is EXCLUSIVE OR gated at E7 and is, sent to the picture data selector circuitry as motion graphic address (MGAG-MGA3), The other input to EXCLUSIVE OR gate E7 is PIC7 from the playfield code multiplexer circuitry. PICT when high causes the output of £7 to be complimented. For example, if GAO-MGA3 are low, PICT causes MGAO-MGAS to go high. This causes the motion object video to be inverted top to bottom, Motion Object Circuitry (Horizontal)

The motion object circuitry (horizontal) receives playfield data and horizontal inputs from the sync generator circultry. PFD16-PFD23 from the playfield memory determine the horizontal position of the motion object. PFD24-PFD29 trom the playfield memory determine the indirect {olor of the motion object. PEDI6-PFD2S are latched by L7 and loaded Into the horizontal position counters AS and BS by a low on pin 9. The horizontal position counters then address video RAMS A6 and B6. These RAMS are loaded with the video data forthe particular motion object from shift registers H9 and J9 (which were loaded from the graphics ROM). The output for RAMs A6 and B6 Is then sent to the color PROM circuitry as MRO and MRI.

From Syne Generator Sheet 1, Side 8 Picture Data ROM Circuitry

The picture data ROM circuitry receives picture Information, assigns a color code to the information ‘and sends it tothe color PROM circuitry. The picture ‘data ROM circuitry consists of ROM devices F7 and HN7, multiplexers FB, H8, J8, KB, shift registers HO ‘and J9, and latch F8.

‘The picture ROMS receive (PICOPICS) trom the playfield code multiplexer, MGAOMGA3 (motion Qraphics address) from the motion object circuitry, 256H and 256A from the sync generator. PICOPICS represent the code for the object to be displayed. MGAO-MGA3 set one of eight different combina tions of the Bine by Bit blocks of picture video or the 16 line by 8 bit Blocks of motion object video.

256H when high selects the playfield picture cot fr codes to be addressed. 256H when low selects the motion object color codes to be addressed. The picture data ROM output D1-D8 on F7 and HIN? are ‘multiplexed by F8, H8, 8 and K8 and shifted out ser. {ally at HO and J9. This serial output Is latched by F9. ‘as AREAO and AREAI to the motion object horizon tal circuitry and the video output circuit.