CATHODE RAY TOMES

Omega Race Parts and Operating Manual (0929-00300-0000)

Omega Race (set 1) (Midway, 1981) · Parts & Operating Manual · 109 pages · 30 sections · original scan

Page 1

Game Nos. 929, 930, 931, & 894

MIDWAYS

NO. 931 MINI

“NO, 930 COCKTAIL

MIDWAY MFG. CO. A BALLY COMPANY

10750 W. GRAND AVENUE FRANKLIN PARK, ILLINOIS 60131 USA

Phone: (312) 451-1360 Cable Address: MIDCO Telex No.: rss

FORM NO. 0829-00300-0000

Page 2

TABLE OF CONTENTS

PAGE

INTRODUCTION 0.0... ccc ccc eee teen eee n eee eee n eter tee 1

LOCATION AND SETUP .......0 0... ccc e ec e ccc eect e nee n ete eee tense nee ene 3

MAJOR DIFFERENCES 3 INSPECTION INSTALLATION SELF TEST GAME VOLUME ADJUSTMENT CONTROLS . OPTION SWITCH SETTINGS ...............04. PICTURE SIZE — HORIZONTAL AND VERTICAL GAME OPERATION .........ccccceee cece eee eenenesteeeeeneceereeeneeneeneee 17 TO mmMoOO My

REMOVAL OF MAIN DISPLAY GLASS AND T.V. BEZEL .. T.V. MONITOR REPLACEMENT PRINTED CIRCUIT BOARD REPLACEMENT . OPENING THE ATTRACTION PANEL ....... COIN DOOR MAINTENANCE ......... REPLACING ULTRAVIOLET TUBE ...............5 -ro7mcem>

ILLUSTRATED PARTS LIST

OMEGA RACE — CONTROL KNOB ASSY. OMEGA RACE — CONTROL KNOB ASSY. — PARTS LIST NO. 929 — OMEGA RACE UPRIGHT — FRONT ...........-- NO. 929 — OMEGA RACE UPRIGHT — FRONT — PARTS LIST .. o . NO. 929 — OMEGA RACE UPRIGHT — REAR ACCESS ............-00000e +. 64 NO. 929 — OMEGA RACE UPRIGHT — REAR ACCESS — PARTS LIST ... +. 65 NO. 929 — OMEGA RACE UPRIGHT — FLUORESCENT FIXTURE ASSYS. ........ 66 NO. 929 — OMEGA RACE UPRIGHT — FLUORESCENT FIXTURE ASSYS. — PARTS LIST oo... ccc cece cere ener ene en eee ene nen eee n en ee eee ee 67 NO. 894 — OMEG E SIT DOWN ....... ce eee eee -. 68 NO. 894 — OMEGA RACE SIT DOWN — PARTS LIST ......... +. 69 NO. 894 — OMEGA RACE SIT DOWN — FRONT INTERIOR ACCESS ...........45 70 NO. 894 — OMEGA RACE SIT DOWN — FRONT INTERIOR ACCESS — PARTS LIST 71 NO. 894 — OMEGA RACE SIT DOWN — REAR INTERIOR ACCESS ............005 72 NO. 894 — OMEGA RACE SIT DOWN — REAR INTERIOR ACCESS — PARTS LIST 73 NO. 894 — OMEGA RACE SIT DOWN — CONSOLE & FLUORESCENT FIXTURE ASSYS. occ ence enn enn eee n bene eee ne eee ee ee eenenete 74 NO. 894 — OMEGA RACE SIT DOWN — CONSOLE & FLUORESCENT FIXTURE ASSYS. — PARTS LIST

NO. 931 — OMEGA RACE MINI — PARTS LIST ... NO. 931 — OMEGA RACE MINI — REAR ACCESS

Page 3

“* OLLWWAHOS — (GYVvOd Y3LHONVG) GuvOgd 3NVO LNOAVT LNSNOdWOO — (GuyOg Y3LHONV) auvog AWVD OILVWAHOS — QYvVOd YHAHLOW

  • LNOAVT LNANOdWOO — GHVO8 YHSHLOW “"* OLLWNAHOS — *G’O'd AlddNS YAMOd LNOAV] LNANOdWOO — “@'0'd AlddNS HAMOd vererees NMOG LIS — WVYHDVIC ONIYIM “* TWLHOOO — WVHOVIG DNIHIM aaa INIA — WYHDVIG SNIYIM LE tere trees eee scr sess ee sees esses reerees LHDId¥dN — WVHYDVIO ONIXIM SWVYDVIC ONINIM ® SOLLVWAHOS GuyvOg AWVD — FOV" VOANO
  • GYVOd YSHLOW HOLOSA — 30VY VOANO
  • * LSITSLYVd — ‘ASSV YOOd LNOYS — SNOISHSA 11V — 30VYH VOANO BB testes “ASSV HOOO LNOWd — SNOISHAA 11V — 30V" VOANO LQ rete rss s es sr sees ses ee sees 1SI1 SLYVd — ‘ASSV HAL 14d — 3OVY VOAWO Se ee eee eee reese “ASSV Y311I4 — JOVY VOANO
  • LSI1 SLUVd — ‘ASSV GHYVO8 YAWHOSNVHYL — FOV VOAWO Teeese sees ee eee e ere ere eres. “ASSV GHVOG HAWHOASNVHYL — S0VY VOANO eect LSIT SLUVd — SSAOOV HOINSLNI — T1IVLHOOO 30VY VOAWO — 086 ‘ON _ SSSHOOV YOINALN! — 1IVLHOOO 3JOVY VOAINO — 0€6 “ON soeese sees es cee eweeeerreess 1S! SLYVd — TIVLYDOO 3OVY VDAWO — 0&6 ‘ON OB cts sree see eseeces ees ee sees TVLHOOO JAOVY VOAWO — O€6 ‘ON (pauod) SLNALNOOS 4O 31EaVvi
Page 4

|. INTRODUCTION

Page 5

OMEGA RACE

IMPORTANT NOTE DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read sections I. and II. of this manual completely. It will not take more than a few minutes and it may be very helpful.

Il. INTRODUCTION

OMEGA RACE is a one or a two player game with one exception; the “SIT DOWN” model. This model is for one player at a time ONLY. The other models are the “UPRIGHT”, “MINI”, and “COCKTAIL TABLE”. When the two player mode is selected on one of these, the piayers take turns at the controls to fly their space ship(s) through the game course. If you have purchased the cocktail table model of this game, the rules of play are the same. The only difference is that in the two player mode of the cocktail table game, the picture flips to face you when it is your turn.

When playing this game, you are the pilot of an Omegan Space Fighter in training to defend Omega’s Star Colonies. You are stationed in space to destroy as many waves of attacking enemy droid ships as possible.

You begin your training with a smail number of droid ships in the first wave of attackers and gradually build your skill until there is amaximum number of 12 attacking droid ships per wave. These attaching ships not only move independently and fire at you, they also drop two different kinds of space mines to block your path and your shots at them.

As your skill level increases, the speed with which the droid ships attack is gradually increased and their shots at you become more accurate.

Bonus ships are awarded to you periodically throughout the game as you reach or pass certain preselected point values. Each enemy ship and mine has a point value as listed in Figure 1.

PHOTON MINE ao POINTS

VAPOR MINE — POINTS ~

DROID SHIP . : POINTS

COMMAND SHIP - POINTS

DEATH SHIP - : POINTS

FIGURE 1

Page 6

The object of the game is to survive as long as possible while destroying as many attacking droid ships and space mines as you can. As you do this, each following wave of attackers will be harder to destroy.

Page 7

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 8

Il. LOCATION AND SETUP

Page 9

Il. LOCATION AND SETUP

A. MAJOR DIFFERENCES:

A major new feature of your OMEGA RACE game is the addition of an accounting mode. This mode provides the owner/operator with coin and credit information, numbers of one and two player games played, free ships given, average score per game, highest score, average seconds per game, maximum seconds per game, and current credits on the game.

Your OMEGA RACE game will remember this information even if the power to it is turned off for a period of time.

B. INSPECTION

1.

2. Remove the game from its shipping crate. Inspect the entire outside of it for any signs of damage. a. Any scratches?, dents?, cracks? b. Any broken controls? c. Any broken glass or plastic? d. Just look it over closely and make a note of any signs of damage.

  • Remove the shipping cleats from the bottom of the cabinet. See Figure 2. . Install the four levelers, one at each corner of the cabinet. See Figure 2. a. Level the. cabinet. . Open-the cabinet and inspect the inside of the game for any signs of damage. See Figure 3, a. Also check to make sure all plug-in connectors on the wire harness are firmly seated.
NOTE: All connectors or plugs are keyed so they will only go together when all pins are properly lined up. b. Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO

CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily,

assuming the keys are lined up, it either does not belong there or is damaged. c. Make sure ali printed circuit boards (P.C.B.’s) are firmly seated in their connectors. See Figure 3. These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged. d. Note the location of the game’s serial number. See Figure 3. e. Check all major sub assemblies to be sure they are mounted securely. These are called out in Figure 4. i. Power supply.

ii. Control panel(s). iii. T.V. monitor.

iv. Other P.C.B.’s and/or P.C.B. rack, etc.

v. Power supply filter assembly. vi. Transformer board assembly.

Page 10

UPRIGHT

SHIPPING CLEATS

SITDOWN

SHIPPING CLEATS

OPTIONAL COCKTAIL TABLE LEGS

FIGURE 2 COCKTAIL

LEG LEVELER ANB NUT

Page 11

UPRIGHT CHECK THAT ALL PLUG IN CONNECTORS ARE SEATED FIRMLY

ON/OFF SERIAL NUMBER = SWITCH

UPRIGHT

FIGURE 3

Page 12

SERIAL NUMBER

ON/OFF SWITCH

SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER)

ON/OFF SWITCH za (LOCATED UNDER CABINET ON PLAYER NO. 2 SIDE) COCKTAIL

FIGURE 3 (cont'd)

Page 13

SITDOWN

SERIAL NUMBER

SITDOWN

CHECK THAT ALL PCB’S ON/OFF ARE SEATED FIRMLY SWITCH

SITDOWN

FIGURE 3 (cont'd)

Page 14

MOTHER BOARD & POWER SUPPLY GAME BOARD TRANSFORMER FILTER ASSY (DAUGHTER BOARD) BOARD ASSY

TV MONITOR

CONTROL PANEL

UPRIGHT

FIGURE 4

Page 15

CONTROL PANEL

TV MONITOR

INTERLOCK SWITCH

MOTHER BOARD & POWER SUPPLY PCB

GAME BOARD (DAUGHTER BOARD) POWER SUPPLY FILTER ASSY

TRANSFORMER ~_ BOARD ASSY (NOT SHOWN)

FIGURE 4 (cont'd)

Page 16

CONTROL PANELS

at,

SITDOWN

MOTHER BOARD & TV MONITOR

GAME BOARD (DAUGHTER BOARD)

POWER SUPPLY FILTER ASSY

CONTROL PANEL f : (2% CONTROL PANEL

i \ (PLAYER NO. 2)

POWER SUPPLY = TRANSFORMER

BOARD ASSY

INTERLOCK SWITCH ~~ (LOCATED INSIDE DOOR) COCKTAIL

FIGURE 4 (cont’d)

Page 17

SITDOWN MOTHER BOARD & GAME BOARD (DAUGHTER BOARD)

POWER SUPPLY PCB

FIGURE 4 (cont'd) INTERLOCK SWITCH

POWER SUPPLY FILTER ASSY

TRANSFORMER BOARD ASSY

Page 18

INTERLOCK SWITCH TV MONITOR

SITDOWN

FIGURE 4 (cont’d)

Page 19
  • Make a note of any problems that can’t be easily corrected.
  • Call your distributor and/or service man about your problem list.

C. INSTALLATION

  • Location requirements a. Power

i. Domestic 110V @ 60 Hz ii. Foreign 200 to 240V @ 50 Hz b. Temperature - 32° to 100°F (0° to 38°C) c. Humidity - Not over 95% relative d. Space required: i. Upright 25-1/2"W x 30D (64 x 75 cm) ii. Mini 20”W x 24”D (50 x 60 cm) iii. Cocktail 32" W x 22”D (80 x 55 cm) iv. Sit down 26-1/2"W x 48"D (67 x 120cm) e. Game height: i. Upright 70” (175 cm) ii, Mini 59” (148 cm) ili. Cocktail 29” (73 cm) iv. Sit down 64-1/2" (164 cm)

  • Voltage Selection Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the fine voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
  • Interlock and power On/Off switches - See Figure 4. a. To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright, Mini, and Sit Down models). b. When any access door is opened, the interlock switch installed there turns off all power to the game.

c. Check each interlock switch for proper operation. i. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected

Page 20

properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. il, The game On/Off switches for all four models are located as shown in Figure

  • Turn the game on and allow it to warm up for a few minutes. iii. Slowly open each access door to the game (this does not include the coin door on the Upright, Mini, and Sit Down models).

@ As the door is opened approximately 1” (2.54 cm) the power to the game

should go off (the T.V. monitor, all the lights, and all sounds will stop). @ If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. @ If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch.

@ Plug the game back into the wall outlet, close the access door, and turn it on.

@ After the game has warmed up, repeat the above interlock switch test. iv. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out. THIS IS TO BE USED ONLY FOR SERVICING THE GAME.

D. SELF-TEST Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game’s speaker system. See Step H. GAME OPERATION for a more detailed discription of this function.

When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).

E. GAME ADJUSTMENT CONTROLS: See Figure 5. The game volume control pots are located on the left hand side of the daughter board as you face it. There are only two pots, one above the other. For adjustment, they may be reached through the rear access door on the Upright and Mini models, and through the front access door on the Sit Down models. On the Cocktail Table model, you will need to open the table top to reach them.

As you face them, the right pot controls the right speaker sounds and the left pot controls the left speaker sounds.

To make the sounds louder, turn the wheels on the pots in this direction—~ as you face them.

To make the sounds less loud, turn the wheels on the pots in this direction «—as you face them.

Page 21

F. OPTION SWITCH SETTINGS To change the option switch settings, you DO NOT have to take the daughter board out of the game. They can be easily reached through the rear access door on the Upright and Mini models; and through the front access door on the Sit Down models. On the Cocktail Table model, you have to open the table top to reach them.

When changing any options, ALWAYS perform the Self-Test to be sure the display on the T.V. monitor indicates your new selections. (It is a good idea to actually change the option switches while the game is in the Self-Test mode so you can see the result of the change right then on the screen.) This assures you the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are smali and this can happen.)

The option switch settings and what they will make the game do are shown in Figure 6. See Figure 5 for option switch locations.

G. PICTURE SIZE — HORIZONTAL AND VERTICAL

The picture on the monitor may be expanded or contracted in either the horizontal or vertical direction. This function is controlled by two pots on the mother board located directly behind the daughter board. They are marked “H” for horizontal and “V” for vertical. You will have to reach around behind the daughter board to make this adjustment.

VOLUME CONTROLS ~ LOWER<<——__—

OPTION SWITCHES

FIGURE 5

Page 22

MAELLLITPTL ALLA AA ALAS GEA OVP SWITCH AD SSSA TTSLSATATAA AAS LAAT Ist BONUS SHIP AWARDED AT:

SW#2

ONON40,000 POINTS
OFFON50,000 POINTS
ONOFF70,000 POINTS
OFFOFF100,000 ___ POINTS

2nd AND 3rd BONUS SHIPS AWARDED AT:

2ne 3rd BONUS BONUS

Sw#3swe4SHIPSHIP
ONON150,000 POINTS250,000 POINTS
OFFON250,000 POINTS500,000 POINTS
oNOFF500,000 POINTS750,000 POINTS
OFFOFF750,000 POINTS1,500,000 POINTS

SHIPS PER CREDIT

1 CREDIT = 2 SHIPS / 2 CREDITS = 4

OFFON1 CREDIT = 2 SHIPS / 2 CREDITS = 5 SHIPS
ONOFF1 CREDIT = 3 SHIPS / 2 CREDITS = 6 SHIPS
OFFOFF1 CREDIT = 3 SHIPS / 2 CREDITS = 7 SHIPS

~ = = NOT USED - - = SWAT 7 SW#8 ee ee ee COINS PER CREDIT COIN SWITCH #1 1S CONTROLED BY SW#T,2,63

SWATSw#2SwH3
OFFOFFOFF1 COIN1 CREDIT
ONOFFOFF2 COINS1 CREDIT
OFFONOFF2 COINS3 CREDITS
ONONOFF3 COINS4 creoits
OFFOFFON4 COINS5 CREDITS
ONOFFON1 COIN5 CREDITS
OFFONon1 COIN3 CREDITS
ONowON1 COIN2 CREDITS

COIN SWITCH #2 IS CONTROLED BY SW#4,5,66

sweuswswe6
OFFOFFOFF1 COIN1 CREDIT
ONOFFOFF2 COINS1 CREDIT
OFFONOFF2 COINS3 CREDITS
ONONOFF3 COINS4 CREDITS
OFFOFFon4 coINs5 CREDITS
ONOFFON1 COIN5 CREDITS
OFFONoni COIN3 CREDITS
ONowON1 COIN2 CREDITS

PLAY NODE

Swi? OFF FREE PLAY (CREDIT REMAINS AT 4) ON COIN PLAY COCKTAIL TABLE MODELS

Swe8 aN THIS 1S THE NORMAL POSITION FOR THIS SWITCH IN THE UPRIGHT, MINI, AND SIT DOWN MODELS.

OFF THIS 1S THE NORMAL POSITION FOR THiS SWITCH IN THE COCKTAIL TABLE MODELS. (IT ENABLES THE GAME TO FLIP THE PICTURE WHEN {T |S THE OTHER PLAYERS TURN AND 10 RECEIVE INSTRUCTIONS FROM THE SECOND SET OF CONTROLS.’

FIGURE 6

Page 23

H. GAME OPERATION

OMEGA RACE, with the exception of the Sit Down model, is a one or a two player game with a black and white T.V. monitor. The game gives a display which has all the parts shown in Figure 7.

The game has six possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE INITIAL, SELF-TEST, and RECORD KEEPING.

  • Record Keeping Mode: The Record Keeping mode is a unique mode to give the owner/operator research information about game play activity. You may enter the Record Keeping mode at any time after the game has been turned on by sliding the Self-Test switch to the “ON” position. See Figure 8. When this is done, the game will react as follows: a. Ifthe gameis in the Attract mode or the Ready-To-Play mode when the Self-Test switch is moved to the “ON” position, several seconds (5 to 10) will go by and then it will display the Record Keeping ledger. b. If the game is in the Play mode when the Self-Test switch is moved to the “ON” position, it will NOT go into the Record Keeping mode unti) AFTER the last omegan defender has been destroyed (the game must be over). At this point,

several seconds (5 to 10) will go by and then it will display the Record Keeping

ledger.

OMEGAN SPACE FIGHTER (PLAYER SHIP) PHOTON MINE VAPOR MINE

econe 11050 unst scone

DEATH SHIP DROID SHIP COMMAND SHIP

FIGURE 7

Page 24

TEST SWITCH

FIGURE 8

c. When in the Record Keeping mode: i. The T.V. monitor will give the following display: See Figure 9. ii. Anytime a coin acceptor switch is tripped, the game will register a “TEST CREDIT” in the Record Keeping ledger but will not advance the coin counting meter on the coin door. iii. Pushing the “THRUST” button will set the “CURRENT CREDIT” count to zero “0”. (This is the last line on the ledger display.) iv. Pushing the “FIRE” button will set the 1 and 2 player high score values to 38,250 points at the same time.

v. Holding in the “1 PLAYER 1 CREDIT” button while at the same time pressing

the “1 PLAYER 2 CREDIT” button will set all information in the Record Keeping ledger to zero “0”. d. To go from the Record Keeping mode back to the game’s other modes (ATTRACT, READY-TO-PLAY, etc.) simply slide the Self-Test switch back to the “OFF” position.

Page 25

FIGURE 9 RECORD KEEPING DISPLAY

COIN CHUTE 1 —— COIN CHUTE 2 —— TOTAL CREDITS — TEST CREDITS —

1 CREDIT 2 CREDIT

1 PLAYER GAMES——
*2 PLAYER GAMES——
FIRST FREE SHIP=——
SECOND FREE SHIP——
THIRD FREE SHIP——
AVERAGE SCORE—__
HIGHEST SCORE——a
AVERAGE SEC. PER GAME_——
MAXIMUM SEC. PER GAME—a

CURRENT CREDIT __

*THIS WILL ALWAYS READ ZERO “0” ON THE SIT DOWN MODEL

  • Self-Test Mode: The Self-Test mode is a special mode made up of 4 test displays for checking game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game. You may begin a Self-Test at any time by turning the power to the game off. See Figure 3 for the location of the game ON/OFF switches on all four models. Slide the Self-Test switch to the “ON” position as shown in Figure 8, and turn the power to . the game back on. When this is done, the game will react as follows:

a. The game displays a ROM/RAM check [ist as shown in Figure 10. The entire ROM/RAMcheck list Shown in Figure 10 flashes off and on at regular intervals every few seconds.

If a bad ROM or RAM chip is found by the game’s internal check system: it is indicated visually by the letters “NG” on the display in place of the letters “OK”, and phonically by “BEEPING” at you from the moment you turn it on. For instance: if the 7th chip down from the top is found to be bad, “NG” will appear in front of this chip (P RAM 3 NG) and the game will “BEEP” at you 7 times from the moment you turn it on. It will wait a few seconds (10 to 15) after the 7th “BEEP” and repeat the 7 “BEEPS” again. \f you have two chips that were found to be bad by the game's internal check system, they would both be shown on the display with the letters “NG” in front of them and the game would “BEEP” at you in a slightly different manner.

Page 26

FIGURE 10 — ROM/RAM CHECK LIST AND MOTHER BOARD LOCATION COORDINATES

ROM 1OKM-7
PROM 2OKL-7
PROM 3OKaadK-7
PROM 4OKJ-7
PRAM 1OKS-3 and/or S-2
PRAM 2OK—R-3 and/or (R/S)-2
PRAM 3OK-— — P-3 and/or (P/R)-2
BBURAMOKS-4
myRAM 1OKH-1 and/or (M/N)-1
VvRAM 2OKJ-1 and/or (L/M)-1
VvRAM 3OK — —L-1 and/or (K/L)-1
VvRAM 4OK—(J/K)-1 and/or (N/P)-1
VvROM 1OK_E-1
VvROM 2OK—F-1

If completely bad, no picture and no “BEEP” sound. ** If completely bad, no picture.

For instance: if the 7th and the 12th chips down from the top are found to be bad, they would look. like this (P RAM 3 NG) and (V RAM 4 NG). In the above case, the “BEEPING” sequence would be as follows:

7 “BEEPS”, PAUSE (2 to 5 seconds), THEN 12 MORE “BEEPS”, LONGER PAUSE (10 to 15 seconds), THEN REPEATS ABOVE SEQUENCE.

NOTE: In addition to the “BEEPING”, the game will also flash its 1 and 2 credit LED lit push buttons at you in sequence with the “BEEPS” -7 “BEEPS”, 7 “flashes” - 12 more “BEEPS”, 12 more “flashes” - and so on. These "BEEPING” and “FLASHING” sequences are repeated until the game is turned off and the bad chip(s) are replaced or until the Self-Test switch is turned off. When there is a bad chip, the game will not advance to the next Self-Test display by pressing the “FIRE” button. Ali bad chips must be replaced BEFORE the game will advance to the next Self-Test display. The meaning of each part of this test display is explained in Figure 11. b. When in the Self-Test mode, you advance to the next display by pressing the “FIRE” button onetime. Do so now. Figure 12 shows you what the next display in the Self-Test series (SWITCH OPERATION TEST) looks like. As you move each of the switches indicated above you will observe that the indications change from “HI” to “LOW” or from “LOW” to “HI”. If you move a switch and its indication on the monitor fails to change, the switch is either not working, miswired, or disconnected. Check it out thoroughly. The meaning of each part of this test display is explained in Figure 13.
Page 27

FIGURE 11 DISPLAY EXPLANATION

ROM 1OKThe “P” stands for PROGRAMMABLE.

ROM 2 OK

ROM 3OKThe “ROM” stands for READ ONLY MEMORY.

ROM 4 OK The “1, 2” etc. is the number of that particular

RAM 7OKchip.

RAM 2 OK

RAM 3NGThe “OK” means this particular chip is good.
RAMOK“BBU” stands for BATTERY BACK UP.
RAM 1OKThe “RAM” stands for RANDOM ACCESS
RAM 2OKMEMORY.

RAM 3 OK

RAM 4NGThe “V” stands for VECTOR.
ROM 1OKThe “NG” stands for NO GOOD.

ROM 2 OK

NOTE: An indication of “Hi” means that that particular switch is in the “OFF” condition or is a “normally open” switch. An indication of “LOW” means that that particular switch is in the “ON” condition or is a “normally closed” switch. After having tested ail the switches in your game, you are ready to advance to the third display of the series. . Press the “FIRE” button one time. Figure 14 shows you what the next display should look like.
NOTE: This pattern and the one that wil! follow are for use in adjusting or checking the monitor's brightness and linearity. . Press the “FIRE” button one time. Figure 15 shows you what the next and last display should look like.

. Pressing the “FIRE” button one more timhe will cause the monitor screen to go

blank and a tone to begin coming from first one of the game’s speakers and then

the other.

The tone is high in pitch to begin with and goes lower over a 2 to 3 second Period. When the tone stops at the end of the 2 to 3 second period, the game switches speakers and repeats the tone through this speaker.

The game will continue alternating back and forth between speakers to aid you in adjusting the volume level heard through each. To get out of the Volume Adjustment mode and advance to the beginning of the Self-Test mode, proceed in either one of the two following ways: i. Atleast four beeps of tone must be heard to come from the game’s speakers before you do anything. At any time after those first four beeps of tone are heard, depress and hold down the “FIRE” button. You will hear another two

Page 28

FIGURE 12 SWITCH OPERATION TEST

COIN 1 HI COIN 2 HI TILT HI P 1 THRUS HI P 1 FIRE HI TEST LOW

P 2 THRUS HI P 2 FIRE HI 2P1CR HI 2P2CR HI 1P1CR HI 1P2CR HI

ANGLE 12Low
ANGLE 13HI
ANGLE 14Hi
ANGLE 15Low
ANGLE 16Low
ANGLE 17LOW
ANGLE 2oHI
ANGLE 21HI
ANGLE 22HI
ANGLE 23.HI
ANGLE 24HI
ANGLE 25Hi
DIPSW10Low
DIPSW11Low
DIPSW12LOW
DIPSw13LOW
DIPSW14HI
DIPSW15LOW
DIPSW16LOW
DIPSW17LOW
DIPSW20HI
DIPsw21HI
DIPSw22.HI
DiPSw23.HI
DIPSw24Hi
DIPsw25HI
DIPSw26LOW
DIPSw27LOW

to three beeps of tone while you’re holding down the “FIRE” button and then the game will return to the beginning of the Self-Test mode (the ROM/RAM check list).

ii. The second way to get out of the Volume Adjustment mode and return to the beginning of the Self-Test mode is to quickly turn the game “OFF” and back “ON” again.

g. Slide the Self-Test switch to the “OFF” position. The game functions and display will now return to the T.V. monitor.

Page 29

FIGURE 13 DISPLAY EXPLANATION

TILT SWITCH,COIN 1HIl=—> COIN SWITCHES, mounted on
mounted on back ofCOIN 2HIback of coin door,

coin door-—___, TILT Ht PLAYER NO. 1 THRUST BUTTON : P 1 THRUS HI

NOTE: P41 FIRE Hi<—— PLAYER NO. 1 FIRE BUTTON.
P2THRUS and P 2)TESTLOW ~— SELF-TEST SWITCH.

FIRE are only used

in the COCKTAILP 2 THRUSHI +—— PLAYER NO. 2 THRUST BUTTON
TABLE model of this |“p 2 FIREHI ~—— PLAYER NO. 2 FIRE BUTTON.
game.2P1CRHI ~—— 2 PLAYER 1 CREDIT BUTTON.

2P2CR HI ~—— 2 PLAYER 2 CREDIT BUTTON.

NOTE: 1P1CR HI ~—— 1 PLAYER 1 CREDIT BUTTON.
2P1CRand2P2CR1P2CRHt «-——— 1. PLAYER 2 CREDIT BUTTON.

are NOT used in the 4

SIT DOWN model ofANGLE 12LOWThese ANGLE SWITCHES are
this game.ANGLE 13HIcontrolled by moving the
ANGLE 14HIspace craft “ROTATE” control
ANGLE 15LOWin a complete circle.
ANGLE 16LOW
ANGLE 17Low |
ANGLE 2OoHI7]These ANGLE SWITCHES are
ANGLE 21HIonly on the COCKTAIL TABLE
ANGLE 22HImodel of the game.
ANGLE 23HIThey are controlled by moving
ANGLE 24HIthe PLAYER NO. 2 “ROTATE”
ANGLE 25HI|control in a complete circle.

DIPSW1 0 LOW] DIPSWITCH PACK NO. 1 is

DIPSW11LOWmounted on the DAUGHTER
DIPSW12LOWBOARD. It is the one farthest from
DIPSW13LOWthe MOTHER BOARD.
DIPSW14HI
DIPSW15LOW
DIPSW16LOW
DIPSW17LOW]
Dipsw20HI]DIPSWITCH PACK NO. 2is also
DIPSWw21HImounted on the DAUGHTER
DIPSW22HiBOARD. right below DIPSWITCH

DIPSW2 3 HI iS PACK NO. 1. It is the one closest

DIPSWw24HIto the MOTHER BOARD.
DIPSw25HI
DIPSW26LOW
DiPSWw27LOWKA
NOTE: While in the Self-Test mode, the game functions and display WILL NOT reappear (come back) by just sliding the Self-Test switch to the “OFF” position. You MUST be in the ROM/RAM portion of the displays BEFORE you can get out of Self-Test and back into game play. Just push the “FIRE” button to cycle through any remaining displays. When you reach the ROM/RAM display portion of the Self-Test mode, (assuming the Self-Test switch is already in the “OFF” position), the game will pop out of Self-Test and into normal game functions.
Page 30

FIGURE 14 SINGLE DIAMOND PATTERN WHICH FILLS THE MONITOR SCREEN

FIGURE 15 BOX WITH CROSS AND BRIGHTNESS SCALE IN THE CENTER

ABOVE DISPLAY FILLS THE MONITOR SCREEN

Page 31
  • Attract Mode:

The Attract mode starts:

a. As soon as power has been turned on to the game. (Self-Test switch is in the “OFF” position.) b. After play has been finished, the score was not high enough to put the game into the High Score/Initial mode, there are still credits left in the game memory but no One pushes one of the flashing “1 PLAYER 1 CREDIT”, “1 PLAYER 2 CREDIT”, etc. push buttons. (It will take one minute and then the Attract mode will begin.) c. After a play has been finished, the score was not high enough to put the game into the High Score/Initial mode, and there are no more credits left in its memory. d. After the High Score/Initial mode when there are no more Credits left in its memory. e. The Attract mode is on all the time and is only stopped when a game has been paid for and the Record Keeping or Self-Test modes have not been started. f. In the Attract mode, the game will give the following displays centered on the monitor screen:

NOTE: With regard to the lettering shown in each “display”: When the lettering

is ALL CAPITALS, it is the lettering actually shown on the T.V. monitor screen. When the lettering is all lower case, it does not actually appear on the T.V. monitor screen.

display #1

IN THE YEAR 2003, THE OMEGAN SYSTEM DEVELOPED A METHOD OF TRAINING ITS WARRIORS TO PROTECT THEIR STAR COLONIES. OVER THE CITY OF KOMAR, ANDROID CONTROLLED FIGHTERS RACED TO ENGAGE AND DESTROY THESE OMEGAN WARRIORS. : L

POINTS WERE AWARDED FOR. THE. ABILITY TO. NEUTRALIZE THIS DROID FORCE AS FOLLOWS.

display #2 photon mine POLNES

vapor mine+POINTS
droid ship<POINTS
command ship~POINTS
death ship-~POINTS
Page 32

display #3

THE OMEGAN METHODS SO SUCCESSFUL 1T-COMMANDS FEAR AND RESPECT FROM ALL THROUGHOUT THE GALAZIES. THE METHOD 1S CODE NAMED. - |

OMEGA RACE

display #4

1 PRED TT GANE ALL TIME HtGn

106550 MEG

DALLY Hibs

70650 DOK S1is3s0 OL M HHS Mic CRS

@@ sae: ntouny neo. ca

display #5

2 CREDIT GAME ALL TIME HIGH 398250 AE

DALLY HIGHS

919350 OLM 30500 MICE 23350 Les 22400 fae Be 1955.0 ROW

BG imei nines neo. co.

Page 33

display #6

scare £1050

uaa scone

display #7 t CREDIT GAME ALL TIME HIGH

166550 MPG

DATLY HIGHS

70650 DOK 91350 OLM 30550 HHS 30500 MIC 23350 CRS

@@ tse: Krowny wre. co

display #8

2 EREDIT GANE ALL TIME HIGH

38250 AE

DAILY HIGHS

S919350 oLM 90500 Mic 23350 CRS 22400 Ae 15550 FO

OG se: nroway nro £o

Page 34

display #9

switch selectable =<

display #10

display #11 OMEGA RACE

1 COIN = 1 CREO T

==a@ COINS = 2 CREOITS

1 CREOIT GAME AL ere IE ort. Ee LOBSSO MEG

DAN eS

7OE5SO OOK 91950 DL mM 30950 HHS 30500 mic 23350 ers

OQ sae: nripans nea. co.

2 CREDIT GAME ALL TIME HIGH

“8B250 AE

DAILY HIGHS

31350 DLM 30500 (tas He 23350 Les 22400 JAC 19550 PD

BO wseienioumy aro, co

Page 35

g. No matter where the game is in the 11 display Attract mode sequence, it will immediately go to display #12 as soon as a game has been paid for. It will hold this display on the monitor screen for a minute. If, at the end of that minute, the player has not pushed one of the flashing “1 PLAYER 1 CREDIT”, “1 PLAYER 2 CREDIT", etc. start buttons, the game will go back to the beginning of the Attract mode sequence.

switch selectable

Ceneois anne. RR vaceeott anne - du tut hy de dy te

aonus sHiPs at “ooo y80000 280000

PRESS ONE OF -FHE FLASHING BUTTONS GR INSERT ADDITIONAL COINS

cweott og

display #12

4, Ready-To-Play Mode: a. The Ready-To-Play mode starts when enough coins have been accepted fora 1 or a 2 player game. b. The Ready-To-Play mode ends when one of the flashing “1 PLAYER 1 CREDIT”, “4 PLAYER 2 CREDIT”, etc. pushbuttons is pressed. c. In the Ready-to-Play mode, the game will give the above “display #12” centered on the monitor screen.

d. If no START button is pressed, the game will hold the above display on the screen for one minute before going back to the beginning of the Attract mode sequence.

  • Play Mode: a. The Play mode begins when one of the flashing “1 PLAYER 1 CREDIT”, “1 PLAYER 2 CREDIT”, etc. start buttons is pressed. b. The Play mode ends when all of your Omegan fighters have been destroyed. When this happens, all the enemy driods and mines disappear and “GAME OVER” is written across the top center of the screen. c. The game is made up of an energy field through which the Omegan ‘pilot’ flys his space fighter to attack and destroy the invading enemy droid forces. (See Figure 7 for a sample display and an explanation of all its components.)
Page 36

vi.

vii. There are four initial waves of enemy droids in the first droid force. These waves are made up of:

1st WAVE = 6 ENEMY DROID SHIPS 2nd WAVE = 8 ENEMY DROID SHIPS 3rd WAVE = 10 ENEMY DROID SHIPS 4th WAVE = 12 ENEMY DROID SHIPS

If one of your Omegan space fighters is hit by the enemy or runs into an enemy mine BEFORE the last enemy ship of that wave is destroyed; when play begins again, you will have to re-destroy ALL of that SAME wave of enemy droids all over again BEFORE you can advance to the next wave.

If, however, one of your omegan space fighters is hit by astray enemy ray or

runs into an enemy mine AFTER the last enemy ship of that wave has been destroyed, you are advanced to the next wave of enemy droids even though you lost a ship. When you destroy the last enemy ship of the fourth wave of attackers, the T.V. monitor will give the following display centered on the screen: FIRST DROID FORCE ELIMINATED 5000 BONUS POINTS

iv. Each wave of enemy droids after the fourth wave is made up of 12 ships. Each droid force after the 1st is made up of 4 waves of enemy ships. You are awarded an additional 5000 BONUS POINTS for each and every droid force you eliminate.

As you destroy ever larger numbers of enemy droids, they move faster and their aim gets even better. . Two Player Operation The Upright, Mini, and Cocktail Table models are the ONLY ones that have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however. @ in the Upright and Mini models, the players must take turns at the controls.

@ In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn. (When it is not your turn. your set of controls will have no effect on the game.) @ When a bonus ship is awarded to a player in atwo player game, it is played immediately following the destruction of the ship he is currently piloting. (This enables the game to END at the SAME TIME for BOTH players. One player does not have to stand around after all his ships have been destroyed and watch the other one piay.)

Page 37

Il. MAINTENANCE AND REPAIR

Your OMEGA RACE game needs certain types of maintenance to keep it in good working order. Clean, well maintained games attract players and earn more profits.

The most important thing for you to rémember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should.

The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.

A. CLEANING

The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors, hot soapy water may be used on the plastic ones and any household cleaner may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor.

DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CAN NOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.

B. FUSE REPLACEMENT

This game contains several fuses located as shown in Figure 16.

  • Upright model: As viewed from the back, facing the cabinet, with the rear access door removed, the fuses are located on the Mech. Panel, the Linear Power Supply Board, and on the Power Supply Filter Assembly.
  • Mini model:

As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Mech. Panel, the Linear Power Supply Board, and the Power Supply Filter Assembly.

  • Cocktail Table model: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Mech. Panel, the Linear Power Supply Board, and the Power Supply Filter Assembly.
  • Sit Down model:

As viewed from the front, facing the cabinet, with the front access door open; the fuses are located on the Mech. Panel, the Linear Power Supply Board, and on the Power Supply Filter Assembly. As viewed from the rear, facing the cabinet, there is one fuse by the ON/OFF switch.

Page 38

Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual.

POWER SUPPLY PCB

UPRIGHT

MECH. PANEL FILTER ASSY

POWER SUPPLY PCB

“~—FILTER ASSY. (NOT SHOWN) MECH PANEL— (NOT SHOWN)

MINI

FIGURE 16

Page 39

SITDOWN MECH. PANEL

POWER SUPPLY (XFMR BD)

PCB FUSE

FILTER ASSY

MECH. PANEL

POWER SUPPLY PCB

COCKTAIL

FIGURE 16 (cont'd)

Page 40

C. OPENING THE CONTROL PANEL — See Figure 17.

  • Upright model: a. The control panel is held in place by two latches, one on the left side and one on the right side of the cabinet. . i. They are spring loaded to provide constant positive pressure on their latch plates. ii. They can be reached through the coin door AFTER turning power to the game off.

iii. To release the latches, lift up and toward the center of the control panel. @ Once they are released, unhook them from their latch plates. b. To remove the control panel: i. Raise it up and tilt it toward you until you can see the cable behind it.

ii. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. iii. The contro! pane! is now free and can be removed. c. To reinstall the control panel, reverse this procedure.

  • Mini model: a. The control panel is held in place by two latches, one on the right side and one on the left side of the cabinet.

i. They are spring loaded to provide constant positive pressure on their latch plates. ii. They can be reached through the coin door AFTER turning power to the game off. iii. To release the latches, lift up and toward the center of the control panel. @ Once they are released, unhook them from their latch plates. b. To remove the control panel: i. Raise it up and tilt it toward you unti! you can see the cable behind it.

ii. Cradling the contro! panel between yourself and the cabinet, disconnect it from its cabling. iii. The control panel is now free and can be removed. c. To reinstall the control panel, reverse this procedure.

  • Cocktail Table model: a. Each control panel is held in place by several screws, two on the inside of the cabinet and three along the bottom edge of the contro! panel. i. Turn power to the game off. ii. Open the coin box door and release the two latches indicated in Figure 18.
CAUTION: The left hand latch is very close to the sharp metal edge on the monitor chassis. Be careful not to cut yourself when working the latch.

® Once they're released, unhook them from their latch plates. iii. Grasp the table top at “A” and open it as indicated in Figure 18.

Page 41

LATCHES FOR CONTROL PANEL CAN BE REACHED THROUGH MINI

UPRIGHT COIN DOOR.

FIGURE 17

CLAMPS

“ye

FIGURE 18

CAUTION: Due to the weight of the monitor, EXTREME CASE MUST be taken when opening the cabinet.
Page 42

iv. Remove the screws which secure the control panel in place. See Figure 19. b. To remove the control panel(s): i. Disconnect it from its cabling. ii. The control panel is now free and can be removed.

REMOVE (2) SCREWS

REMOVE (3) SCREWS ON , BOTTOM OF SHELF

COCKTAIL

FIGURE 19

Page 43

4, Sit Down model:

There are three control panels on aSit Down model, one at the bottom of the screen which contains the “START GAME” “1 CREDIT” and "2 CREDIT” buttons, one in the right hand arm rest which contains the “THRUST” and “FIRE” buttons, and one in the left hand arm rest which contains the “ROTATE” control.

a. These control panels are held in place by semi-tamper-proof screws. b. Turn the power off to the game.

c. To remove either arm rest control panel: (See Figure 20.) i. Remove the three screws which secure it. ii. Grasping it at its bottom front edge, lift it up and tilt it to the side until you can see its cable plug. iii. Unplug it from its cable. iv. The armrest control panel is now free and can be removed. v. To reinstall these control panels, reverse this procedure.

REMOVE (3) SCREWS \\ EACH ARM REST

SITDOWN

FIGURE 20

Page 44

d. To remove the control panel at the bottom of the screen: (See Figure 21.)

NOTE: This control panel CAN NOT be disconnected from its wire harness except by unsoldering the wire harness from the switches. For trouble-shooting purposes, however, the coniro! panel can be lowered slightly so that the pins on the back side of the switches can be reached. To do this, proceed as follows: i. Remove the three screws which secure it. (Make sure you support it as you remove the last of the three screws.) ii. Lower the left hand end of this control panel! and support it on your knees while tilting it toward you to expose the pins at the back of the two switches for trouble-shooting or replacement purposes.
CAUTION: DO NOT pull on the panel to better expose the pins at the backs of the switches. THERE IS NO SLACK IN THIS CABLE!!

iii. To reinstall this control panel, reverse this procedure.

REMOVE (3) SCREWS

SITDOWN

FIGURE 21

Page 45

D. REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY:

  • Upright model:
NOTE: In order to do this, the control panei MUST be removed first. See the “Upright model” procedure. a. Turn the power to the game off and remove the contro! panel. This frees the main-display-glass so it can be lifted up. b. Grasp the main-display-glass in the bottom center, lift up slightly and pull it toward you about an inch, let it down just far enough so you can get hold of its top edge with your other hand and lift it out of the game. See Figure 22. c. Remove the triangular shaped pieces of scenery from the left and right hand sides of the cabinet. See Figure 23. d. Remove the screws which secure the T.V. bezel assembly in place. e. The T.V. bezel assembly is now free and can be slid out of the cabinet. See Figure 23. f. To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure,

DISPLAY GLASS

UPRIGHT |

FIGURE 22

Page 46

BEZEL

REMOVE (2) SCREWS:

FIGURE 23

  • Mini model:
NOTE: In order to do this, the control panel MUST be removed first. See above “Mini model” procedure. a. Turn the power off to the game and remove the control panel. b. Remove the screws which secure the glass clamping plate. See Figure 24. c. Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up.

d. By putting your finger in the hole in the middle of the main-dispiay-glass support, you can lift it up and out. See Figure 24. e. Remove the screws which secure the T.V. bezel assembly, see Figure 25, and lift it out.

NOTE: Use the hole in the center of the main-display-glass support to grasp it. f. Reverse this procedure to reinstall the T.V. bezel assembly and the maindisplay-glass.
Page 47

DISPLAY GLASS

GLASS CLAMPING PLATE

FIGURE 24

BEZEL

REMOVE (2) SCREWS

UPRIGHT

FIGURE 25

Page 48
  • Cocktail Table model:
NOTE: This may be done with the table top in the closed or the open position. If you decide to open the table top, TURN THE POWER TO THE GAME OFF FIRST.

. Remove the screws which secure the table top glass clamps in place.

. Lift out the T.V. bezel assembly. . To reinstall the T.V. bezel assembly, simply reverse this procedure.

  • Sit Down model:

a. Turn the power off to the game. a

b. Remove the table top glass.

c

d

b. Loosen the three screws in the control panel at the bottom of the main-displayglass. See Figure 26. c. Loosen and remove the three screws at the top of the main-display-glass. See Figure 26.

CAUTION: DO NOT let the main-display-glass fall forward. Hold it in place with one hand. d. Grasp the top edge of the main-display-glass with both hands andiift up until its bottom edge is free of the control panel at its bottom. e. Now slide the glass straight down and onto your lap. f. Reverse this procedure to reinstall the main-display-glass.

y REMOVE (3) SCREWS

LOOSEN (3) SCREWS

SITDOWN

FIGURE 26

Page 49

E. T.V. MONITOR REPLACEMENT

CAUTION: High voltages may exist in any television unit, even with power disconnected. Use EXTREME CAUTION and do nottouch electrical parts or the T.V. yoke area with your hands or with metal objects in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The T.V. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.
  • Upright model — See Figure 27. a. Turn power off to the game.

b. Open the rear access door. c. Compietely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE.

d. Unplug the mother board and daughter board from all their cabling. Remove the short P.C.8. supports indicated in Figure 27 and slide the mother and daughter board assembly out the back of the cabinet. Set them aside. (Otherwise the T.V. monitor chassis would hit the daughter board as it was being slid out the back of the cabinet.) e, Before removing the T.V. monitor, the main-display-giass and bezel must be removed. See above “Upright model” procedure. f. With the removal of only four bolts, the T.V. monitor and its mounting board will be loose.

g. The monitor mounting board slides on top of and against two wooden guides mounted to the cabinet's right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 27. h. To reinstall the T.V. monitor, reverse this procedure. i, After replacing the T.V. monitor, be sure to run the game Self-Test.

REMOVE (4) BOLTS (2 EACH SIDE)

REMOVE (2) SUPPORTS <=

Loy gd UPRIGHT

FIGURE 27

Page 50
  • Mini model — See Figure 28.

a.

b.

c. Turn the power to the game off.

Open the rear access door. Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE.

. Before removing the T.V. monitor, the main-display-glass and bezel must be removed. See above “Mini model” procedure. . With the removal of only four nuts, the T.V. monitor will be loose.

CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fall out of the cabinet.

The monitor is removed by supporting it and puiling straight back.

. To reinstall the T.V. monitor, reverse this procedure. . After replacing the T.V. monitor, be sure to run the game Self-Test.

REMOVE (4) BOLTS (2 EACH SIDE)

FIGURE 28

Page 51
  • Cocktail Table model — See Figure 29. a. Turn the power off to the game. b. Open the coin box door and release the two latches indicated in Figure 18.
CAUTION: The left hand latch is very close to the sharp metal edge on the monitor chassis. Be careful not to cut yourself when working the latch.

i. Once the latches are released, unhook them from their latch paltes. c. Grasp the table top at “A” and open it as indicated in Figure 18.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet. . Remove the screws which hold the table top glass clamps in place. . Remove the table top glass. Lift out the T.V. bezel assembly. . Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE.

h. Completely disconnect the mother and daughter boards from all their cabling and slide them out of their supports. a*roa

i. Remove the screws holding the T.V. monitor chassis to its mounting brackets while at the same time supporting it so it can’t move. j. After the last screw is removed, the T.V. monitor may be lifted straight away from the table top’s back side. k. To reinstall the T.V. monitor, reverse this procedure. |. After replacing the T.V. monitor, be sure to run the game Self-Test.

REMOVE (4) SCREWS (2 EACH SIDE)

REMOVE MOTHER BD/ DAUGHTER BD ASSY

L COCKTAIL FIGURE 29

Page 52

4, Sit Down model — See Figure 30. a. Turn the power off to the game.

b. Remove the upper and lower rear access doors:

i. Unlock and open the lower rear access door.

ii. Release the fatches which secure the upper rear access door and unhook them from their latch plates.

iii. The upper rear access door is now free and can be removed.

c. Lift out the scenery.

d. Disconnect the power cable from the lighting tube fixture. e. Remove the screws which secure the lighting fixture and its mounting bracket in place. i. Remove the lighting fixture and mounting bracket assembly and set it aside. f. Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE.

g. Remove the cable clamps at the front edge of the monitor mounting board. See Figure 30,

h, With the removal of the two securing screws, the T.V. monitor and its mounting board will be loose.

i. The monitor mounting board slides on top of and against two wooden guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet.

j. To reinstall the T.V. monitor, reverse this procedure. k, After replacing the T.V. monitor, be sure to run the game Self-Test.

REMOVE SCREWS SITDOWN

REMOVE (2) SCREWS ON EACH SIDE

m REMOVE CABLE CLAMPS REMOVE SCENERY

FIGURE 30

Page 53

F. PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT:

  • Upright model — See Figure 31. a. Turn the power to the game off.

b. Unlock and open the rear access door.

c. Disconnect the daughter board from all its cabling and unplug it from the mother board.

d. Disconnect the mother board from all its cabling, remove the P.C.B. supports indicated in Figure 31, and slide the mother board out the back of the cabinet. e. Disconnect the linear power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 31, and slide the lienar power supply board out the back of the cabinet.

f. To reinstall the above P.C.B.'s, reverse this procedure.

NOTE: P.C.B.’s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connect it to the P.C.B.’s are also keyed and will ONLY go onto their connectors one way without forcing them.

aes a = a aes ce ee ee yO or ee ne See UPRIGHT REMOVE (2) SUPPORTS AND SLIDE PCB’S OUT REMOVE SUPPORT AND SLIDE PCB OUT

FIGURE 31

Page 54
  • Mini model — See Figure 32.

a.

b.

Cc. Turn the power off to the game.

Unlock and open the rear access door.

Disconnect the daughter board from al! its cabling and unplug it from the mother board.

. Disconnect the mother board from ail its cabling, remove the P.C.B. supports indicated in Figure 32, and slide the mother board out the back of the cabinet. . Disconnect the linear power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 32, and slide the linear power supply board out the back of the cabinet.

To reinstall the above P.C.B.’s, reverse this procedure.

NOTE: P.C.B.’s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connect it to the P.C.B.'s are also keyed and will ONLY go onto their connectors one way without forcing them.

REMOVE (2) SUPPORTS AND SLIDE PCB’S OUT REMOVE SUPPORT AND SLIDE PCB OUT

FIGURE 32

Page 55
  • Cocktail Table model —

a, Turn the power off to the game.

b. Open the cabinet: i. Open the coin box door and release the two latches indicated in Figure 18.

CAUTION: The left hand latch is very close to the sharp metal edge on the monitor chassis. Be careful not to cut yourself when working the latch.

® Once they're released, unhook them from their latch plates. c. Grasp the table top at “A” and open it as indicated in Figure 18.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet. d. To remove the linear power supply board — See Figure 33. i. Disconnect it from all its cabling. ii. Remove the two smallest P.C.B. supports. iii, Once these are removed, the linear power supply can be lifted out of the cabinet.

iv. To reinstall the linear power supply board, reverse this procedure,

REMOVE (2) SCREWS

wa AND SLIDE PCB OUT

REMOVE (2) SUPPORTS AND LIFT PCB OUT

REMOVE (2) SUPPORTS AND SLIDE PCB OUT

COCKTAIL

FIGURE 33

Page 56

e. To remove the mother and daughter boards — See Figure 33. i. Disconnect the daughter board from all its cabling. ii. Remove the nylon retainer screws at its upper right and left hand corners. iii, The daughter board is now free and can be siid from its bracket. iv. Disconnect the mother board from all its cabling. . v. Remove the screws from the P.C.B. supports indicated in Figure 33 and then remove the supports. vi. The mother board is now free and can be slid from its P.C.B. supports. vii. To reinstall the mother and daughter boards, reverse this procedure.

  • Sit Down model — See Figure 34. a. Turn the power off to the game.

b. Unlock and open the front access door.

c. Disconnect the daughter board from all its cabling and unplug it from the mother board.

d. Disconnect the mother board from all its cabling. e. Remove the screws indicated in Figure 34 and the mother board plus its mounting assembly are now free to be slid out of the cabinet. f. Disconnect the linear power supply from all its cabling. g. Remove the screws from the P.C.B. supports indicated in Figure 34 and then remove the supports. h. The linear power supply is now free and can be slid from its P.C.B. supports. i. To reinstall the above mother, daughter, and linear power supply boards, reverse this procedure.

REMOVE SCREWS TO TAKE COMPLETE ASSY FROM CABINET

REMOVE SUPPORT AND SITDOWN SLIDE PCB OUT

FIGURE 34

Page 57

G. OPENING THE ATTRACTION PANEL(s):

  • Upright model: The upright model has two attraction panels, one at the very top of the cabinet and one in the middle just below the control panel. a. Turn the power off to the game.

b. Opening the attraction panel at the top of the cabinet — See Figure 35:

Remove the screws which secure the top bracket in place. (They are on its top side.) Remove the top bracket and slide up the attraction panel. This exposes the attraction panel light bulbs and their mounting board.

® To service the light bulbs and their mounting board: @@ Turn the power to the game back on so you can see which bulbs are burnt out.

@® Mark the burnt out bulbs and turn the power to the game back off again. @e To replace the burnt out bulbs, grasp them gently and puil straight out. The new bulbs are gently pushed into the empty sockets. © To completely remove the light bulb mounting board: e@e Remove the control panel and main-display-glass as described previously and unplug the mounting board from its power cable. @e Remove the screws that hold the mounting board to the cabinet. @@ Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything.

c. Replacing the Speakers — See Figure 35:

Be sure the power is off to the game.

Remove the control panel and main-display-glass and disconnect the speakers from their cabling. Remove the screws which secure the speaker grill in place and set the speaker grill aside. . The bolts which secure the speakers in place are now accessible. Once the bolts which secure the speakers in place are removed, the speakers may be removed through opening where the main-display-glass was.

d. Servicing the light behind the attraction panel in the center of the cabinet below the control panel. Remove the control panel as described previously. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly.

The fluorescent light tube may be replaced at this time by reaching through

the space where the control panel was before you removed it and around the light tubes mounting bracket assembly.

Page 58
WARNING: If you drop a fluorescent tube and it breaks, 1T WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube. iii. Replacing the fluorescent tube starter — ®@ Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket.

iv. Replacement of the fluorescent tube mounting bracket assembly - © Be sure the power is off to the game.

® Disconnect it from its power cable.

@ Remove the screws along its base which secure it to the cabinet and remove it.

e. To reinstall any of the items removed above, reverse this procedure.

REMOVE (3) SCREWS ATTRACTION SPEAKER GRILL PANEL SCREWS(8) | SLIDE UP

SPEAKER GRILL

ATTRACTION PANEL

UPRIGHT

FIGURE 35

Page 59
  • Mini model — See Figure 36:

a.

b.

c. Turn the power off to the game.

Remove the screws from the top of the top bracket.

Remove the top bracket and slide up the attraction panel. This exposes the attraction panei light bulbs and their mounting board. . To service the light bulbs and their mounting board: i. Turn the power to the game back on so you can see which bulbs are burnt out.

ii. Mark the burnt out bulbs and turn the power to the game off again. ili. To replace the burnt out bulbs, grasp them gently and pull straight out. @ The new bulbs are gently pushed into the empty sockets.

REMOVE (8) SCREWS

ATTRACTION PANEL

t SLIDE UP

SPEAKERS

MINE

FIGURE 36

Page 60

iv. To completely replace the light bulb mounting board: @ Open the cabinet rear access door and unplug the mounting board from its power cable.

@ Remove the screws that hold the mounting board to the cabinet. @ Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. e. To replace the speaker(s) — i. Be sure the power is off to the game.

ii. Disconnect the speaker(s) from its cabling. iii. Remove the nuts and bolts securing the speaker(s) to be replaced. iv. Slide the speaker(s) out through the rear access door. f. To reinstall any of the items removed above, reverse this procedure.

  • The Cocktail Table model and the Sit Down model have no back lit attraction panels.

H. COIN DOOR MAINTENANCE

  • Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.

a. Make sure the power to the game is off.

b. Unlock and open the coin door.

d. Remove the coin acceptor mechanism(s) as shown in Figure 37. i. Push down on the two spring loaded latches.

ii. While holding the latches down, pull the top of the coin acceptor mechanism

toward you.

iii, Release the latches and lift out the coin acceptor mechanism.

d. Clean the magnet of all foreign particles. See Figure 38. i. This may be accomplished by swinging the gate open as shown in the above figure. e. Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) i. Also clean the pivot pin. f. Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner. i. Place the coin acceptor in boiling water for about ten minutes.

CAUTION: BE CAREFUL NOT TO BURN YOURSELF. ii. Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit.

iii. Rinse the coin acceptor in clean boiling water. iv. Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

Page 61
NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

PUSH DOWN ON Se

LATCHES AND PULL (Qa. COIN MECH OUT \

SITDOWN

FIGURE 37

GATE OPENS AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

FIGURE 38

Page 62

g. To lubricate the coin acceptor. i. Use ONLY powdered graphite and put it ONLY on the moving parts of the coin Acceptor. These parts are called out in Figure 39. ii. Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.

WARNING

DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.

h. Check the coin chute for obstructions such as: paper, gum, etc.

i. Reinstall the coin acceptor to the coin door.

i. Place the two pegs at the coin acceptor’s base into their retaining slots. ii. Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.

j. Close and lock the coin door.

  • The plastic coin acceptor mechanisms must be removed periodically from the coin door and cleaned.

a. Make sure the power to the game is off.

b. Unlock and open the coin door.

c. Remove the coin acceptor mechanism(s) as shown in Figure 37.

i. Push down on the two spring loaded latches. ii. While holding tne latches down, pull the top of the acceptor mechanism toward you.

ili. Release the latches and lift out the mechanism.

APPLY POWDERED GRAPHITE HERE

UNDERSIZE LEVER

“E” RINGS

FIGURE 39

Page 63

d. Squeeze the two pins indicated in Figure 40 together to open the mechanism and break it down into its three basic parts.

i. Clean the mechanism in hot soapy water. It never rusts.

ii. Rinse the mechanism in clean hot water and allow it to dry. iii. Reassemble the mechanism (it never needs lubrication). e. Check the coin chute for obstructions such as: paper, gum. etc.

SQUEEZE PINS TOGETHER SWING BOTH GATES OPEN TO UNLOCK

HOLDING BOTH GATES TOGETHER PUSH UP AND PULL OUT

FIGURE 40

Page 64

f. Reinstall the coin acceptor to the coin door.

i. Place the two pegs at the coin acceptor’s base into their retaining slots.

ii. Now push the top of the coin acceptor toward the coin door until it snaps in

place and is held by the two spring loaded latches.

g. Close and lock the coin door.

NOTE: See Figure 41 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

MAGNET

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO > ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO ~——_ EXTREME LEFT.

FIGURE 41

Page 65
  • REPLACING THE ULTRAVIOLET LIGHT TUBE; STARTER; AND THE MOUNTING BRACKET ASSEMBLY.
  • Upright model a. Turn the power to the game off.

b. Remove the rear access door. c. Remove the scenery . d.

. The ultraviolet light tube may now be removed and replaced in the same manner

you would any ordinary fluorescent tube.

WARNING: If you drop an ultraviolet light tube and it breaks, IT WILL IMPLODE! Shattered glass from the implosion can fly six (6) feet or more. Use care when replacing any ultraviolet light tube.

e. Replacing the ultraviolet light tube starter — i. Be sure the power is off to the game.

ii. Grasp the starter (it is on the back side of the mounting bracket), give it a quarter turn, and remove it from its socket. iii. To reinstall the starter, reverse this procedure. f. Replacement of the ultraviolet light tube mounting bracket assembly — i. Be sure the power to the game is off.

ii. Disconnect the power cable leading to the mounting bracket assembly. iii. Remove the screws which hold the mounting bracket assembly to the right and left hand sides of the cabinet. BE SURE to support it as you remove the last two screws so it does not fall.

iv. The ultraviolet light tube mounting bracket assembly is now free and can be removed.

v. To reinstall the above assembly, reverse this procedure.

  • Sit Down model

a. Turn the power off to the game.

. Remove the lower rear access door. . Remove the scenery .

you would any ordinary fluorescent tube.

WARNING: If you drop an ultraviolet light tube and it breaks, IT WILL IMPLODE! Shattered glass from the implosion can fly six (6) feet or more. Use care when replacing any ultraviolet light tube. e. Replacing the ultraviolet light tube starter — Qo0o0

i. Be sure the power to the game is off. ii. Grasp the starter , give it a quarter turn, and removeit from its socket.

iii. To reinstall the starter, reverse this procedure.

Page 66

f. Replacement of the ultraviolet light tube mounting bracket assembly — i. Be sure the power to the game is off.

ii. Disconnect the power cable leading to the mounting bracket assembly. iii. Remove the screws which hold the mounting bracket assembly to the right and left hand sides of the cabinet. BE SURE to support it as you remove the last two screws so it does not fall.

iv. The ultraviolet light tube mounting bracket assembly is now free andcan be removed.

v. To reinstall the above assembly, reverse this procedure.

  • The Mini and Cocktail Table models have no ultraviolet lighting.
Page 67

\V. ILLUSTRATED PARTS BREAKDOWN

Page 68

OMEGA RACE — CONTROL KNOB ASSY.

OMEGA RACE — CONTROL KNOB ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

1A894-00008-0000KNOB & SHAFT ASSY. — S.D. ONLY
1A929-00021-0000KNOB & SHAFT ASSY. — U.R., C.T., MINI ONLY
20017-00101-0308#8-32 x 3/16 SET SCREW
30017-00104-0109NYLON WASHER
40017-00101-0620#8-32 x 1/2 CARRIAGE BOLT (2 REQ'’D.)
5A894-00022-0000LEFT CONSOLE/OVERLAY ASSY. — S.D.
50929-00102-00XFCONTROL PANEL — U.R.
50930-00100-00XFCONTROL PANEL — PLYR. #1 — C.T.
50930-00100-01XFCONTROL PANEL — PLYR. #2 — C.T.
50931-00102-0000CONTROL PANEL — MINI
6A894-00010-0000BEARING & PLATE ASSY.
70017-00104-0062#8 FLAT WASHER (2 REC'D.)
80017-00103-0061#8-32 HEX NUT W/SEMS
90017-00104-0010#8 EXT. LOCKWASHER
100894-00701-00XFSTABILIZER POST NUT
W0017-00042-01733/16 NYLINER
120017-00100-00183/16 E-RING
130017-00104-00451/2 1\.D. FLAT WASHER
140017-00100-00501/2 E-RING

0894-00112-00XF ENCODER STASILIZER A082-91110-A000 P.C. ENCODER ASSY. W/HARDWARE CONSISTING 3/8 INT. LOCK- WASHER & 3/8-32 NUT.

Page 69

AA ey. NO. 929 — OMEGA RACE UPRIGHT — FRONT

Page 70

NO. 929 — OMEGA RACE UPRIGHT — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0929-00904-00XF A929-00013-0000 0929-00909-0000 0017-00003-0219 0017-00031-0002 0929-00100-00XF 0017-00101-00117 0929-00105-00XF 0017-00101-00117 0017-00003-0187 0017-00101-0118 0017-00103-0061 A929-00011-0000 0929-00901-O0XF 0537-00903-0049 0537-00903-0034 0629-00902-0800 0929-00916-0100 0929-0091 2-0100 0929-00907-O00XF 0929-00912-6200 0929-00916-0200 0929-00902-0000 0929-00102-00XF 0929-00908-0000 0017-00101-0341 0961-00115-OOXF 0017-00101-0607 0017-00103-0041 A929-00021-0000 0017-00042-0256 0017-00042-0257 0017-00032-0093 0017-00032-0092 0929-00905-00XF 0929-00903-00XF A929-00022-0000 A090-00300-06BK 0090-00002-02BK 0017-00101-0121

0929-00915-0000 0929-00913-0000 0935-00906-0300 0017-00102-0048 0017-00103-0526

A929-00031-0000 0929-00906-0000 0929-00914-0000 0929-00106-01XF 0929-00106-02XF 0017-00009-0033 DECORATIVE LEXAN PANEL —.23-7/8" x 4-3/32” x 3/16" LIGHT TRAY INSERT ASSY. LIGHT TRAY BEZEL #194 WEDGE LAMP 14V., .27A. (7 REQ’D.) S11 LAMP HOLDER ASSY. (7 REQ’D.) INSERT BRKT. #8 x 5/8 PHIL TRS. HD. SCR. (3 REQ'D.) SPEAKER PANEL GRILL #8 x 5/8 PHIL. TRS. HD. SCR. (8 REQ'D.) 6” x 9” SPEAKER 8 OHM, 9W (2 REQ’D.) #8-32 x 1-1/8 CARRIAGE BOLT (8 REQ'D.) #8-32 HEX NUT W/SEMS (10 REQ’D.) FLUORESCENT BRKT. ASSY — NOT SEEN MAIN VIEWING GLASS — 23-13/16" x 20-5/8" x 3/16" GLASS CHANNEL — 17-3/4" LG. (2 REQ’D.) GLASS CHANNEL — 23” LG. (2 REQ'D.) GLASS LIFT CHANNEL — 20” LG. RIGHT FRONT SIDE SCENERY RIGHT SIDE SCENERY BACK SCENERY CARD LEFT SIDE SCENERY — (NOT SEEN) LEFT FRONT SIDE SCENERY — (NOT SEEN) MIRROR — 23-27/32" x 19-3/4" x 1/4” CONTROL PANEL CONTROL OVERLAY — DECORATIVE #6 x 1/4 PHIL. TRS. HD. SCR. (4 REQ'D.) STRIKE (2 REQ’D.) #8-32 x 3/8 HEX HD. BUTTON SCR. (4 REQ'D.) #8-32 LOCK NUT (4 REQ’D.) KNOB & SHAFT ASSY. PUSH BUTTON ASSY. — RED PUSH BUTTON ASSY. — YELLOW P.B. SWITCH W/HOLDER (2 REC'D.) LIGHTED RED P.B. SWITCH (4 REQ'D.) SWITCH BEZEL (4 REQ’D.) LOWER HEADER — DECORATIVE LOWER FLUOR. BRKT. ASSY. — NOT SEEN DOUBLE ENTRY COIN DOOR ASSY. LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) DECAL — FRONT DECAL — CABINET SIDES (2 REQ'D.) KICK PLATE 23-7/8" LG. 3/8-16 x 2" LEG LEVELERS (4 REQ'D.) 3/8-16 LEG LEVELER HEX NUTS (4 REQ'’D.)

NOT SHOWN LIST T.V. BEZEL ASSY. BEZEL TRANSPARENT VINYL OVERLAY — 20” x 13-1/2" CONTROL SHELF BRKT. SUPPORT — RIGHT CONTROL SHELF BRKT. SUPPORT — LEFT BASSICK CLAMP (2 REQ'D.)

Page 71

NO. 929 — OMEGA RACE UPRIGHT — REAR ACCESS

Page 72

NO. 929 — OMEGA RACE UPRIGHT — REAR ACCESS PARTS LIST ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

A627-00066-0000 ON/OFF SWITCH ASSY. 0894-00913-0000 RECESSED HAND LIFT (2 REQ’D.) 0017-00101-0117 #8 x 5/8 PHIL. TRS. HD. SCR. (12 REQ’D.) 0017-00003-0324 ELECTROHOME — 19" B&W MONITOR & CHASSIS (OR) WELLS-GARDNER — 19” B&W MONITOR & CHASSIS 1/4-20 x 1-1/4 UNSLT. HEX BOLT. (4 REQ’D.) FLAT WASHER (4 REQ’D.) DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ'D.) FORMED MONITOR FISHPAPED SHIELD INTERLOCK SWITCH ASSY. LINEAR POWER SUPPLY ASSY. P.C. SUPPORT BRKT. — 12”LG. (3 REQ'D.) P.C. SUPPORT BRKT. — 2-1/2” LG. (3 REQ’D.) P.C. SUPPORT BRKT. — 6" LG. (4 REQ'D.) #8 x 1/2 SLT. HEX HD. SCR. (20 REQ'D.) #8 FLAT WASHER (20 REQ'D.) GAME LOGIC BRD. ASSY. (DAUGHTER BRD.) MOTHER BRD. ASSY. P.C. SUPPORT BRKT. ASSY P.C. SUPPORT BRKT. ASSY. #6 x 3/8 SLT. HEX HD. SCR. (6 REQ'D.) 125V — FILTER ASSY. TRANSFORMER BRD. ASSY — LOCATED NEXT TO FILTER ASSY. CASTER ASSY. (2 REQ'D.) WHEEL BRKT. (2 REQ’D.) PLASTIC WHEEL (2 REQ’D.) SHAFT (2 REQ'D.) 3/8" E-RING (2 REQ'D.) 16 FT. LINE CORD 0017-00003-0325 0017-00102-0012 0017-00104-0046 0017-00104-0014 0017-00103-0018 0929-00910-0000 A151-00027-0000 A082-90413-D000 0624-00902-0100 0624-00902-0300 0624-00902-0500 0017-00101-0025 0017-00104-0037 A084-91372-G929 A084-90007-H929 A597-00012-0100 A597-00012-0200 0017-00101-0096 A945-00002-0000 A929-00006-0000 A961-00007-0000 0961-00109-0000 0017-00042-0255 0894-00702-00XF 0017-00100-0037 0017-00003-0064

ADDITIONAL PARTS LIST TERMINAL STRIP ASSY. CASH BOX — MOLDED CASH BOX COVER ASSY. CASH BOX SIDE CHANNEL ASSY. CASH BOX SIDE CHANNEL — LONG #8-32 x 3/4 CARRIAGE BOLT (4 REQ'’D.) #8 FLAT WASHER (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) BACK DOOR LOCK ASSY. 5-5/8" SQ. VENT GRILL (4 REQ'D.) HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE SIGNAL CABLE ASSY. MASTER CABLE ASSY. COIN DOOR CABLE ASSY. CONTROL SHELF CABLE ASSY. MOTHER & DAUGHTER BRDS. BRKT. ASSY. A031-00004-0000 0017-00009-0477 A961-00008-0000 A894-00024-0000 0894-00121-0000 0017-00101-0628 0017-00104-0022 0017-00103-0061 A151-00029-0000 0017-00009-0490 A929-00028-0000 A929-00027-0000 A929-00026-0000 A894-00035-0000 A929-00023-0000 A894-00031-0000

Page 73

NO. 929 — OMEGA RACE UPRIGHT — FLUORESCENT FIXTURE ASSYS.

Page 74

NO. 928 — OMEGA RACE UPRIGHT — FLUORESCENT FIXTURE ASSYS. — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

UPPER FLUORESCENT BRKT. ASSEMBLY 0929-00101-0000 FLUORESCENT BRKT. — UPPER 0017-00003-0095 18" BLACK LIGHT LAMP — F15T8 0017-00021-0005 FLUORESCENT LOCKS (2 REQ’D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ’D.) 0017-00021-0079 FLUOR. STARTER HOLDER 0017-00101-0573 #6-32 x 1/2 PHIL. R.H.M.S. (4 REQ’D.) 0017-00003-0019 STARTER 0017-00003-0026 BALLAST . 0017-00101-0593 #8-32 x 1/4 SLT. PAN HD. MSS. (2 REQ’D.) 0017-00021-0096 2 PINSOCKET CONNECTOR A929-00030-0000 FLUOR. CABLE ASSY.

LOWER FLUORESCENT BRKT. ASSEMBLY 0929-00107-0000 FLUORESCENT BRKT. — LOWER 0017-00003-0043 18" COOL WHITE LAMP 0017-00021-0005 FLUORESCENT LOCKS (2 REQ'D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ'D.) _ 0017-00003-0412 FLUOR. STARTER HOLDER W/LEADS 0017-00101-0573 #6-32 x 1/2 PHIL R.H.M.S. (4 REQ'D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00003-0019 STARTER 0017-00003-0026 BALLAST 0017-00101-0598 #8-32 x 5/16 SLT. HEX. HD. SCR. (2 REQ’D.) 0929-00104-0000 RETAINER BRKT. 0017-00101-0025 #8 x 1/2 SLT. HEX HD. SCR. (3 REQ'D.) 0929-00903-00XF LOWER HEADER — DECORATIVE A929-00032-0000 CABLE ASSY.

Page 75

NO. 894 — OMEGA RACE SIT DOWN

Page 76

NO. 894 — OMEGA RACE SIT DOWN — PARTS LIST

ORDER BY PART NUMBER ONLY PART NO. DESCRIPTION 0017-00009-0393 BLACK SPEAKER GRILL W/SLOTS (6 REQ’D.) 0017-00003-0187 | 6” x 9" SPEAKERS 8 OHM, 9W (2 REQ’D.) 0017-00101-0127 | #8-32 x 1-1/2 CARRIAGE BOLT (80 REQ’D.) 0017-00101-0126 #10-32 x 3/4 HEX HD. BUTTON SCR. (4 REQ’D.) 0017-00104-0062 #8 FLAT WASHER (20 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (20 REQ'D.) 0894-00913-00xF | RECESSED HAND LIFT (2 REQ’D,) 0017-00101-0117 | #8 x 5/8 PHIL. TRS. HD. SCR. (12 REQ’D.) 0894-00900-0000 CANOPY — ACRYLIC 0894-00103-00XF | PLEXI RETAINING STRAP — LOWER 0894-00104-00xF | PLEXI RETAINING STRAP — UPPER 0017-00100-0114 BLACK NYLON FINISHING WASHER (9 REQ’D.) 0017-00101-0029 } #8 x 1" PHL. OVAL HD. SCR. — BLK. (6 REQ’D.) 0017-00101-0126 | #10-32 x 3/4 HEX HD. BUTTON SCR. (6 REQ’D.) 0894-00113-00xF | HANDLE — EXIT/ENTRY ASSIST (2 REQ’D.) 0017-00101-0126 #10-32 x 3/4 HEX HD. BUTTON SCR. (4 REQ’D.) 0894-00909-00xF | MAIN VIEWING GLASS — 24-13/16" x 12" x 3/16" 0537-00903-0051 GLASS EDGE CHANNEL — 10-3/8 LG. (2 REQ’D.) 0894-00904-0000 ONE WAY MIRROR 0894-00106-00xF | GLASS RETAINER — UPPER 0894-00105-00XF | GLASS RETAINER — LOWER 0017-00101-0126 | #10-32 x 3/4 HEX HD. BUTTON SCR. (6 REQ’D.) 0017-00032-0092 | SMALL RED LIGHTED P.B. SWITCH (2 REQ’D.) 0829-00905-00xF | SWITCH BEZEL (2 REQ’D.) 0894-00910-0100 CORNER CONDUIT — LEFT 0894-00914-0000 SCUFF PROTECTOR 0894-0091 0-0200 CORNER CONDUIT — RIGHT — NOT SEEN 0017-00101-0117 | #8 x 5/8 PHIL. TRS. HD. SCR. (12 REQ’D.) 0894-00911-0000 FLOOR MAT 0894-00109-0000 | THRESHOLD GUARD (2 REQ’D.) 0017-00101-0742 | #8 x 1/2 PHIL. TRS. HD. SCR. (6 REQ’D.) A090-00300-068K | DOUBLE ENTRY COIN DOOR ASSY. 0090-00002-02BK }| LARGE DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. M.S. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0017-00102-0048 | 3/8-16 x 2” LEG LEVELERS (4 REQ’D,) 0017-00103-0026 | 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.) A894-00014-0000 | CASTER ASSY. (2 REQ'D.) NOT SHOWN LIST 0894-00903-0000 SEAT & BACK CUSHIONS (2 REQ’D.) 0017-00102-0052 1/4-20 x 1" UNSLOT. HEX BOLT (6 REQ’D.) 0017-00104-0014 PERIPHERY WASHER (6 REQ'D.) 0894-0091 2-0000 MONITOR MASK 0017-00009-0484 1/8" TAMPER PROOF ALLEN KEY 0017-00032-0083 ON/OFF SWITCH W/NUT

Page 77

NO. 894 — OMEGA RACE SIT DOWN — FRONT INTERIOR ACCESS

Page 78

NO. 894 —- OMEGA RACE SIT DOWN — FRONT INTERIOR ACCESS PARTS LIST

PART NO. DESCRIPTION

A031-00004-0000 0017-00101-0015 A151-00027-0000 A894-00025-0000 0017-00009-0477 A894-00024-0000 0894-00121-0000 0017-G0101-0628 0017-00104-0022 0017-00103-0061 A945-00002-0000 A084-91372-G929 A084-90007-H$29 A894-00032-0000 A597-00012-0100 AS97-00012-0200 0017-00101-0096 0017-00009-0514 0017-00101-0127 0017-00101-0713 0017-00103-0061 A082-90413-D000 0624-00902-0100 0624-00902-0300 0624-00902-0500 0017-00101-0028 0017-00104-0062 A894-00030-0000 A097-00001-0000

A894-00037-0000 A894-00043-0000 A894-00042-0000 A894-00040-0000 A894-00035-0000 A894-00041-0000 A894-00033-0000 0894-00915-0000 ORDER BY PART NUMBER ONLY

TERMINAL STRIP ASSY. #6 x 1/2 SLT. HEX HD. SCR. (2 REQ’D.) INTERLOCK SWITCH ASSY. CASH BOX COVER ASSY MOLDED CASH BOX CASH BOX SIDE CHANNEL ASSY. CASH BOX SIDE CHANNEL — LONG #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) #8 FLAT WASHER (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ'D.) FILTER ASSY. — 125VA GAME LOGIC BOARD ASSY. (DAUGHTER BRD.) MOTHER BOARD ASSY. MOTHER & GAME BOARDS MTG. ASSY. P.C. SUPPORT MTG. BRKT, ASSY. P.C. SUPPORT MTG. BRKT. ASSY. #6 x 3/8 SLT. HEX HD. SCR. (6 REQ’D.) 2-1/2" HINGE (2 REQ’D.) #8-32 x 1/2 CARRIAGE BOLT (4 REQ’D.) #8-32 x 1" SLT. FLT. HD. M.S. (4 REQ'D.) #8-32 HEX NUT W/SEMS (8 REQ'D.) LINEAR POWER SUPPLY ASSY. P.C. SUPPORT BRKT. — 12” LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 6-1/2" LG. P.C. SUPPORT BRKT. — 2-1/2” LG. #8 x 3/4 SLT. HEX HD. SCR. (11 REQ'D.) #8 FLAT WASHER (11 REQ’D.) TRANSFORMER BOARD ASSY. FRONT DOOR LOCK ASSY.

ADDITIONAL PARTS LIST MASTER CABLE ASSY. LOW VOLTAGE TRANSFORMER CABLE ASSY. LOW VOLTAGE CABLE ASSY. A.C. VOLTAGE ASSY. COIN DOOR CABLE ASSY. THRUST-FIRE CABLE ASSY. SWITCH CABLE ASSY. GAME BOARD SHIELD

Page 79

NO. 894 — OMEGA RACE SIT DOWN — REAR INTERIOR ACCESS

a

Page 80

NO. 894 — OMEGA RACE SIT DOWN — REAR INTERIOR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0894-00119-00XF VENT -- ANTI SPILL 0017-00101-0742 #8 x 1/2 PHIL. TRS. HD. SCR. (8 REQ'D.) A866-00026-0000 LOCATING PIN & PLATE ASSY. (2 REQ’D.) 0603-00131-0000 0017-00009-0033 0017-00101-0027 A151-00027-0000 STRIKE (2 REQ’D.) BASSICK CLAMP (2 REQ'’D.) #8 x 3/4 SLT. HEX HD. SCR. (TOTAL REQ'D. 16) INTERLOCK SWITCH ASSY. 0017-00003-0324 ELECTROHOME — 19” B&W, X-Y MONITOR & CHASSIS (OR) WELLS-GARDNER — 19" B&W, X-Y MONITOR & CHASSIS MONITOR HOLD DOWN BRKT. (2 REQ’D.) 1/4-20 x 7/8 SLT. HEX HD. BOLT (4 REQ'’D.) SPLIT LOCK WASHER (4 REQ’D.) FLUORESCENT LIGHT FIXTURE ASSY. FLUOR. REFLECTOR BACKGROUND SCENERY ASSY. 0017-00003-0325 0894-00108-0000 0017-00102-0008 0017-00104-0005 A894-00004-0000 0894-00100-00XF A894-00045-0000

REAR SIDE OF CABINET — NOT SHOWN BLACK SPEAKER GRILL W/SLOTS (2 REQ'D.) #8-32 x 1" CARRIAGE BOLT (8 REQ'D.) 0017-00009-0393 0017-00101-0137 0017-00104-0062 0017-00103-0061 A097-00001-0000 0894-00118-0000 #8 FLAT WASHER (8 REQ’D.) #8-32 HEX NUT W/SEMS (8 REQ'D.) BACK DOOR LOCK ASSY. VENT/ACCESS PLATE 0017-00101-0135, 0894-00114-0000 0017-00101-0135 0017-00003-0178 0017-00003-0155 #8-32 x 3/4 WELD SCREW (2 REQ'D.) LINE CORD/ACCESSORY PLATE #8-32 x 3/4 WELD SCREW (2 REQ’D.) FUSE 3A., 125V. SLO-BLO FUSE HOLDER

Page 81

NO. 894 — OMEGA RACE SIT DOWN — CONSOLE & FLUORESCENT FIXTURE ASSYS.

i |

Page 82

NO. 894 — OMEGA RACE SIT DOWN — CONSOLE & FLUORESCENT ASSYS. — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO.

A894-00011-0000 A894-00022-0000 0894-001 10-0000 0894-00907-0200 0017-00101-0126 A894-00008-0000 A894-00010-0000 A084-91110-A000 DESCRIPTION

LEFT ARM CONSOLE ASSY. LEFT CONSOLE/OVERLAY ASSY. LEFT CONSOLE PLATE DECORATIVE OVERLAY — LEFT #10-32 x 3/4 BLACK HEX HD. BUTTON SCR. (3 REQ'D.) KNOB & SHAFT ASSY. BEARING & PLATE ASSY. ANGLE ENCODER P.C. BRD. ASSY.

A894-00013-0000 RIGHT ARM CONSOLE ASSY.

1A894-00023-0000RIGHT ARM/OVERLAY ASSY.

0894-00107-0000 RIGHT CONSOLE PLATE 0894-00907-0100 DECORATIVE OVERLAY — RIGHT 0017-00101-0126 #10-32 x 3/4 BLACK HEX HD. BUTTON SCR. (3 REQ'D.)

20017-00042-0256RED PUSH BUTTON ASSY.

0017-00042-0257 YELLOW PUSH BUTTON ASSY.

30017-00032-0093PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.)

0017-00103-0054 5/8 PAL NUT (2 REQ’D.)

A894-00004-0000 FLUORESCENT LIGHT FIXTURE ASSY.

10894-00101-0000FLUORESCENT BRKT.
20017-00003-009518" BLACK LIGHT LAMP — F15T8
30017-00021-0005FLUORESCENT LOCKS (2 REQ’D.)
40017-00031-0036FLUORESCENT SOCKETS (2 REQ’D.)
50017-00021-0079FLUOR. STARTER HOLDER

0017-00101-0573 #6-32 x 1/2 PHIL. R.H.M.S. (2 REQ’D.)

60017-00003-0019STARTER
70017-00003-0026BALLAST

0017-00101-0593 A894-00034-0000 #8-32 x 5/16 SLT. HEX HD. M.S. (2 REQ'D.) FLUORESCENT CABLE ASSY.

Page 83

NO. 931 — OMEGA RACE NINI

Page 84

NO. 931 — OMEGA RACE MINI — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0931-00901-0000 DISPLAY PANEL 0017-00101-0117 #8 x 5/8 PHIL. TRS. HD. SCREW (8 REQ’D.) A931-00017-0000 INSERT DISPLAY ASSY. 0017-00031-0030 WEDGE BASE LIGHT SOCKET (5 REQ'’D.) 0017-00003-0219 #194 LAMP 14V, 27A. (5 REQ'D.) 0017-00003-0161 4” SQR. SPEAKER 8 OHM, 3W. (2 REQ'D.) 0017-00009-0482 SPEAKER GRILL (2 REQ’D.) 0017-00101-0136 #8-32 x 1/4 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ'D.) 0931-00902-00XF MAIN DISPLAY GLASS — 17-13/16" x 14-13/16" x 1/8” 0905-00903-0100 GLASS EDGE CHANNEL — 14-1/2" LG. (2 REQ’D.) 0963-00101-00XF GLASS CLAMPING PLATE 0017-00101-0789 ».| #10-32 x 3/4 HEX BUTTON HD. SCR. (2 REQ’D.) A931-00014-0000 CONTROL PANEL & OVERLAY ASSY. 0931-00102-0000 CONTROL PANEL 0931-00905-0000 DECORATIVE OVERLAY 0017-00101-0118 #8-32 x 1-1/8 CARRIAGE BOLT (4 REQ'D.) 0017-00104-0022 #8 FLAT WASHER (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ'D.) 0017-00101-0065 #6 x 1/2 PHIL. TRS. HD. SCR. (2 REQ'D.) ‘A929-00021-0000 KNOB & SHAFT ASSY. 0017-00032-0092 LIGHTED RED P.B. SWITCH (4 REQ'D.) 0929-00905-00XF SWITCH BEZEL (4 REQ'D.) 0017-00042-0256 RED — PUSH BUTTON ASSY. 0017-00042-0257 YELLOW — PUSH BUTTON ASSY. 0017-00032-0093 P.B. SWITCH W/HOLDER (2 REQ'D.) A090-00300-06BK DOUBLE ENTRY COIN DOOR ASSY. 0090-00002-02BK LARGE DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) “ (MOUNTS COIN DOOR TO FRAME) 0935:~00906-0400 KICK PLATE — 17-15/16" LG. — NOT SHOWN 0017-00102-0048 | 3/8-16 x 2” LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)

. NOT SHOWN LIST 0017-00009-0033 -| BASSICK CLAMP (2 REQ’D.) 0961-00115-O0XF STRIKE (2 REQ'D.) 0017-00101-0027 #8 x 3/4 SLT. HEX HD. SCR. (8 REQ’D.) 0961-001 13-0000 SHELF SUPPORT — LEFT 0961-00114-0000 SHELF SUPPORT — RIGHT 0017-00101-0028 #8 x 3/4 BLACK SLT. HEX HD. SCR. (16 REQ’D.)

Page 85

NO. 931 — OMEGA RACE MINI — REAR ACCESS

OO &

Page 86

NO. 931 — OMEGA RACE MINI — REAR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0017-00003-0161 4" SQR. SPEAKER 8 OHM, 3W. (2 REQ'D.) 0017-00003-0358 ELECTROHOME — 15” B&W, X-Y HORIZ. MTG. MONITOR (OR) 0017-00003-0384 WELLS-GARDNER — 15” B&W, X-Y HORIZ. MTG. MONITOR 0592-00104-0100 CHASSIS MTG. BRKT. — R.H 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) 0017-00104-0014 DISH WASHER — .870 DIA. (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) A931-0001 1-0000 T.V. BEZEL ASSY. 0931-00903-0000 T.V. BEZEL 0931-00904-0000 BLUE ACETATE OVERLAY — 14” x 11-3/4" 0934-00905-0000 PLEXI-GLASS A151-00027-0000 INTERLOCK SWITCH ASSY. A082-90413-D000 LINEAR POWER SUPPLY 0624-00902-0100 P.C. SUPPORT BRKT. — 12” LG. (5 REQ'D.) 0624-00902-0300 P.C. SUPPORT BRKT. — 2-1/2” LG. (4 REQ'D.) 0017-00101-0025 #8 x 1/2 SLT. HEX HD. SCR. (23 REQ'D.) 0017-00104-0037 #8 FLAT WASHER (23 REQ’D.) A084-91372-G929 GAME LOGIC BRD. ASSY. (DAUGHTER BRD.) A084-90007-H929 MOTHER BRD. ASSY. AS97-00012-0100 P.C. SUPPORT BRKT. ASSY. A5S97-00012-0200 P.C. SUPPORT BRKT. ASSY. 0017-00101-0096 #6 x 3/8 SLT. HEX HD. SCR. (6 REQ'D.) A945-00002-0000 125 VA — FILTER ASSY. A931-00015-0000 TRANSFORMER BRD. ASSY. — LOCATED NEXT TO FILTER ASSY. A031-00004-0000 TERMINAL STRIP ASSY. 0017-00101-0014 #6 x 1/2 SLT. HEX HD. SCR. (2 REQ’D.) 0017-00032-0083 ON/OFF SWITCH 120V, 6A. 0567-00106-0100 ON/OFF SW. PLATE 0017-00009-0490 5-5/8" SQR. VENT GRILL (2 REQ'’D.)

ADDITIONAL PARTS LIST A905-00028-0000 CASH BOX ASSY. W/HANDLE A961-00008-0000 CASH BOX COVER ASSY. A894-00024-0000 CASH BOX SIDE CHANNEL ASSY. 0894-00121-0000 CASH BOX SIDE CHANNEL — LONG 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) 0017-00104-0022 #8 FLAT WASHER (4 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) A931-00013-0000 MASTER CABLE ASSY. A931-00007-0000 HIGH VOLTAGE CABLE ASSY. A931-00008-0000 LOW VOLTAGE CABLE ASSY. A931-00009-0000 CONTROL SHELF CABLE ASSY. A931-00016-0000 INSERT LIGHT CABLE ASSY. A894-00035-0000 COIN DOOR CABLE ASSY. A866-00049-0000 LINE CORD ASSY. A151-00029-0000 BACK DOOR LOCK ASSY. 0017-00009-0490 5-5/8" SQR. VENT GRILL — BACK DOOR A904-00031-0000 MOTHER & DAUGHTER BRDS. BRKT. ASSY.

Page 87

NO. 930 — OMEGA RACE COCKTAIL

ee ee (a ee ae ae oe ee ~ ja. au

Page 88

NO. 930 — OMEGA RACE COCKTAIL — PARTS LIST

ORDER BY PART NUMBER ONLY

0930-00901-00XF 0775-00104-00XF 0017-00101-0117 3 A930-00009-0000 0930-00900-0000 0931-00904-0000 0934-00905-0000 4 A930-00006-0100 A930-00006-0200 5 0017-00009-0482 0017-00003-0161 0017-00101-0118 0017-00103-0061 6 0017-00009-0393 0017-00003-0187 0017-00101-0136 0017-00103-0061 7 A090-00300-06BK 0090-00002-02BK 0017-00101-0121

8 0017-00102-0048 0017-00103-0026

0017-00032-0083 0567-00106-0100 A151-00078-0000 A930-09007-0000 A930-00010-0000 A962-00005-0000 0962-00101-0000 0017-00101-0628 0017-00104-0022 0017-00103-0061 PART NO. DESCRIPTION

COVER GLASS — 32” x 22” x 1/4” GLASS CLIPS (8 REQ'D.) #8 x 5/8 PHIL. TRS. HD. SCR. (16 REQ’D.) T.V. BEZEL ASSY. T.V. BEZEL BLUE ACETATE OVERLAY — 14” x 11-3/4” PLEXI-GLASS CONTROL SHELF ASSY. — PLAYER #1 CONTROL SHELF ASSY. — PLAYER #2 — NOT SEEN SMALL SPEAKER GRILL 4" SQR. SPEAKER 8 OHM, 7W. #8-32 x 1-1/8 CARRIAGE BOLT (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) SPEAKER GRILL (3 REQ’D.) 6" x 9” SPEAKER 8 OHM, 9W. #8-32 x 1-1/4 CARRIAGE BOLT (12 REQ'D.) #8-32 HEX NUT W/SEMS (12 REQ’D.) DOUBLE ENTRY COIN DOOR ASSY. LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 3/8-16 LEG LEVELER NUTS (4 REQ’D.)

NOT SHOWN LIST ON/OFF SWITCH 120V., 6A. ON/OFF SWITCH MTG. PLATE INTERLOCK SWITCH ASSY. CASH BOX ASSY. CASH BOX COVER ASSY. CASH BOX SIDE CHANNEL ASSY. — SHORT CASH BOX SIDE CHANNEL — SHORT #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) #8 FLAT WASHER (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ'D.)

Page 89

NO. 930 — OMEGA RACE COCKTAIL — INTERIOR ACCESS

NO. 930 — OMEGA RACE COCKTAIL — INTERIOR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0017-00003-0358 ELECTROHOME 15” B&W, X-Y HORIZ. MTG. MONITOR & CHASSIS (OR) WELLS-GARDNER 15” B&W, X-Y HORIZ. MTG. MONITOR & CHASSIS C.R.T. MTG. BRKT. (2 REQ’D.) #10 x 3/4 HEX HD. SCR. (UNSLOTTED) (8 REQ'D.) #10-32 x 3/8 SLT. HEX HD. SCR. (4 REQ’D.) #10-32 HEX NUT W/SEMS (4 REQ'D.) STRIKE (2 REQ’D.) BASSICK CLAMP (2 REQ'D.) — NOT SEEN #8 x 3/4 SLT. HEX HD. SCR. (8 REQ’D.) 0017-00003-0384 0930-00101-0000 0017-00101-0082 0017-00101-0799 0017-00103-0081 0610-00132-0000 0017-00009-0033 0017-00101-0027

Page 90

NO. 930 — OMEGA RACE COCKTAIL — INTERIOR ACCESS — PARTS LIST (cont'd)

PART NO. DESCRIPTION

A084-91372-G929 A084-90007-H929 0624-00902-0100 0624-00902-0300 0017-00101-0027 0017-00104-0037 0017-00009-0514 0017-00101-0639 0017-00103-0061 A082-90413-D000 0624-00902-0100 0624-00902-0300 0624-00902-0500 0017-00101-0027 0017-00104-0037 A945-00002-0000 A730-00011-0000 0017-00003-0310 0017-00009-0485 0869-00909-0000 0870-00700-00XF 0017-00101-0583 0017-00103-0052 0017-00104-0019 0017-00003-0161 0017-00003-0187 0930-00100-01XF 0980-00903-0100 0930-00100-00XF 0930-00903-0200 0017-00101-0341 0930-00103-00XF A929-00021-0000 0017-00042-0257 0017-00042-0256 0017-00032-0093 0017-00032-0092 0929-00905-00XF 0930-00904-0000 0921-00105-00XF 0017-00101-0025 0017-00003-0219 0017-00031-0044 0017-00101-0555

A031-00004-0000 A930-00012-0000 A930-00013-0000 A930-00014-0000 A894-00035-0000 A930-00008-0100 A930-00008-0200 GAME LOGIC BRD. ASSY. (DAUGHTER BRD.) MOTHER BOARD ASSY. P.C. SUPPORT BRKT. — 12” (2 REQ'D.) P.C. SUPPORT BRKT. — 2-1/2” (2 REQ'’D.) #8 x 3/4 SLT. HEX HD. SCR. (10 REQ’D.) #8 WASHER (6 REQ'D.) 2-1/2" HINGE (2 REQ'D.) #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ'D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) LINEAR POWER SUPPLY ASSY. P.C. SUPPORT BRKT. — 12” (2 REQ’D.) P.C. SUPPORT BRKT. — 2-1/2” P.C. SUPPORT BRKT. — 6-1/2” #8 x 3/4 SLT. HEX HD. SCR. (10 REQ’D.) #8 WASHER (10 REQ’D.) 125VA FILTER ASSY. TRANSFORMER BRD. ASSY. EXHAUST FAN 115V., 6OHZ FAN FINGER GUARD FAN SHROUD FAN SPACER (4 REQ'D.) #6-32 x 1-1/4 CARRIAGE BOLT (4 REQ'D.) #6-32 LOCKNUT (4 REQ’D.) #6 FLAT WASHER (4 REQ’D.) 4" SQR. SPEAKER 8 OHM, 7W. 6" x 9" SPEAKER 8 OHM, 9W. CONTROL PANEL — PLAYER #1 DECORATIVE OVERLAY — PLAYER #1 CONTROL PANEL — PLAYER #2 DECORATIVE OVERLAY — PLAYER #2 #6 x 1/4 PHIL. TRS. HD. SCR. (TOTAL REQ’D. 14) BOTTOM SHELF PANEL (2 REQ’D.) KNOB & SHAFT ASSY. (2 REQ’D.) YELLOW — PUSH BUTTON (2 REQ'D.) RED — PUSH BUTTON (2 REQ’D.) P.B. SWITCH W/HOLDER (4 REQ’D.) LIGHTED RED PUSH BUTTON SWITCH (4 REQ’D.) SWITCH BEZEL (4 REQ’D.) LIGHT SHIELD (2 REQ’D.) PANEL SUPPORT BRKT. (4 REQ’D.) #8 x 1/2 SLT. HEX HD. SCR. (20 REQ'D.) #194 WEDGE LAMP 14V., .27A. (4 REQ'D.) WEDGE BASE LAMP SOCKET (4 REQ’D.) #6-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.)

ADDITIONAL PARTS LIST TERMINAL STRIP ASSY. MASTER CABLE ASSY. HIGH VOLTAGE CABLE ASSY. — AC. LOW VOLTAGE CABLE ASSY. — MONITOR COIN DOOR CABLE ASSY. CONTROL SHELF CABLE ASSY. — PLAYER #1 CONTROL SHELF CABLE ASSY. — PLAYER #2

Page 91

“ASSV GUVOE YAWHOSSNVHYL — 30VY VOANWO

Page 92

OMEGA RACE — TRANSFORMER BOARD ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

A945-00013-0000 TRANSFORMER ASSY. W/PINS — MT89-A000 MTO00-00088-A000 TRANSFORMER W/SHIELD 0017-00101-0639 #8-32 x 1-1/4 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ'D.) 0017-00104-0026 1/2” #8 FLAT WASHER (8 REQ’D.) 0017-00101-0052 #6 x 1-1/4 SLT. HEX HD. SCR. (4 REQ’D.) A945-00005-0000 60 HZ CAPACITOR ASSY. 0017-00003-0379 CAPACITOR CLAMP. 0017-00003-0064 NOISE FILTER 0017-00101-0014 #6 x 1/2 SLT. HEX HD. SCR. (17 REQ'’D.) 0720-00001-0100 1 POSITION FUSE CLIP ASSY. (U.R., C.T., & MINI MODELS) 0017-00003-0004 FUSE — 2A, 250V, SLO-BLO 0720-00001-0200 2 POSITION FUSE CLIP ASSY. (U.R., C.T., & S.D. MODELS) 0017-G0008-0260 FUSE — 1/2A, 250V, SLO-BLO (C.T..& U.R. MODELS) 0017-00003-0262 FUSE — 3A, 250V, SLO-BLO (U.R., C.T., & MINI MODELS) 0017-00003-0103 FUSE — 1A, 250V. SLO-BLO (S.D. MODEL ONLY) A866-00049-0000 0017-00021-0478 0017-00021-0479 0017-00021-0480 LINE GORD ASSY. 9 PIN CONNECTOR PLUG 3 PIN CONNECTOR PLUG 3 PIN CONNECTOR CAP

Page 93

OMEGA RACE — FILTER ASSY.

Page 94

OMEGA RACE — FILTER ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

10945-00101-OOXFCHASSIS
20945-00803-0100CAPACITOR — 55000MF — 25vV.
30245-00803-0200CAPACITOR — 100000MF — 15V.
40945-00100-0000CAPACITOR STRAP.

0017-00101-0555 #6-32 x 5/16 SLT. HEX HD. SCR. (4 REQ'D.)

50017-00621-05255 POSITION TERMINAL STRIP (2 REQ'D)

0017-00101-0510 #4-40 x 1/2 SLT. PAN HD. SCR. (4 REQ'D.) 0017-00104-0087 #4 FLAT WASHER (4 REQ'D.) 0017-00104-0071 #4 EXT. TOOTH WASHER (4 REQ'D.) 0017-00103-0002 #4-40 HEX NUT (4 REQ'D.)

60062-122H7-1XXXRESISTOR — 150 OHM, 2W.

0062-086H7-1XXX RESISTOR — 47 OHM, 2W. — LOCATED ON OPPOSITE TERMINAL STRIP

70017-00003-0008FUSE — 6AMP — 120V.
80017-00003-0174FUSE — 10 AMP — 32v.

0945-00805-0000 FUSE HOLDER (2 REQ'D.)

90017-00041 -0008RUBBER GROMMET
10A089-00007-0000FILTER CABLE ASSY. #2
nNA089-00005-0000FILTER CABLE ASSY. #1
120945-00804-0100DIODE — 12A. — 50V. (4-REQ'D.)

0017-00103-0086 0017-00021-0484 0017-00104-0107 0017-00009-0510 0017-00042-0254 0945-00900-0000 #10-32 HEX NUT (4 REQ'D.) SOLDER LUG (4 REQ’D.) #10 FLAT WASHER (4 REQ’D.) INSULATOR (8 REQ'D.) BUSHING (4 REQ’D.) DIODE FORMED FISHPAPER COVER —- NOT SHOWN

Page 95

a

OMEGA RACE — ALL VERSIONS — FRONT DOOR ASSY.

2 @® Pods » ¥

VARIATIONS ARE DEPENDANT ON

MIDWAY’S BASIC COIN DOOR,

YOUR PARTICULAR GAME.

NOTE:

L

Page 96

OMEGA RACE — ALL VERSIONS — FRONT DOOR ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0090-00902-0000 DRESS PLATE 0090-00902-0100 DRESS PLATE W/O BUTTON TO START GAME 0017-00101-0552 #6-32 x 1/4 CARRIAGE BOLT (2 REQ'D.) 0090-00117-03XF COIN ENTRY PLATE (25¢) 0090-00906-0000 PLASTIC START BUTTON 0010-00007-0000 COMPRESSION SPRING A090-00020-2003 DOOR ASSY. DOUBLE ENTRY 0017-00005-0050 DOOR LOCK & KEY WITH SCREW & NUT 0090-00002-02BK DOUBLE DOOR FRAME 0017-00005-0041 421.N.S. CAM 0090-00901-0000 DOOR SWITCH 0090-00126-01XF SWITCH BACKUP PLATE DBOONMAMHM AWN

120017-00101-0528#5-40 x 3/4 LNG. M.S.
130090-00903-950025¢ WINDOW
140090-00143-00XFCOIN PLEX RETAINER
150017-00104-0002SPLIT LOCK WASHER
160017-00007-0019KEY HOOK
170017-00103-0087#6-32 HEX NUT
180090-00010-0000SW. PLATE & OILLITE ASSY.
190017-00100-0018“EB” RING
200090-00131-0000SWITCH
21A090-00087-0100TOP & BTM. COIN CHUTE W/BRKT. ASSY.
220017-00101-0123#8 x 1/4 SCREW
230010-00181-0100SPRING
240090-00129-00XFPIVOT POST
250010-00134-0000SPRING
26A090-00085-0000ACCEPTOR FRAME ASSY.
270693-00155-00XFREJECTOR LEVER
280017-00100-0012“E” RING
290090-00162-00XFCOIN SWITCH MTG. BRKT. — SMALL
290090-00163-00XFCOIN SWITCH MTG. BRKT. — LARGE
300017-00005-0203COIN SWITCH CHUTE — SMALL
300017-00005-0204COIN SWITCH CHUTE — LARGE
310017-00101-0124#6 x 1/4 SCREW
320017-00005-0195COIN SWITCH
330010-00599-0000COIN SWITCH WIRE
340017-00007-0132PUSH-ON RING (BLK.)
350017-00101-0698#4-40 x 3/4 SCREW (. REQ'D.)
360090-00128-00XFSWITCH BRKT. — DOOR TILT

A090-00061-0000 ANTI-STRING DEVICE ASSY. A090-00064-0000 ANTI-PENNY DEVICE ASSY.

Page 97

eS OMEGA RACE

Vector Mother Board #A084-90007-E929

CHIP NUMBER FUNCTION

74LS00 : Quad 2 input Nand 74LS02 Quad 2 input Nor 74LS04 or 74804 - Hex inverter 74LS08 Quad 2 input And T4LS10 Triple 3 input Nand 74LS14 Hex Schmitt-Trigger 74LS20 _ Duai.4 input Nand 74LS32 Quad 2 input Or 74LS42 BCD to decimal decoder 74LS74 Dual “D” Flip-Flop 74LS83 4 bit binary adder 7497 6 bit rate multipliers 74LS109 ~ . Dual “JK” Flip-Flop 74LS138 <3 to 8 line. decoder 74LS139 Dual 2 to 4 line decoder 74LS157 Quad 2 to 1 line multiplexer 74LS161 7 4 bit binary counter 7ALS174 Hex “D” Flip-Flop 74LS175 Quad “D” Flip-Flop 74LS191 . Synchronous up-down counters 74LS193 Up-down counter with dual clock 74LS244 Octal buffer 74LS245 Octal bus tranceiver 74LS273 Octal “D” Flip-Flop 74LS367 ~ Hex bus driver 74LS374 Octal “D” Flip-Flop 74LS393 Dual 4 bit binary counter 74LS670 . 4 by 4 register files Z80 CPU 2114 1K x 4 Ram 2716 2K x 8 Prom 2532 4K x 8 Prom 9316 2K x 8 Rom 9332 4K x 8 Rom MI-7611-5 Prom 5101 256 x 4 Ram UPD8216 4 bit bus tranceiver ADS561 Digital to analog converter TLO81 Operational amplifier TLO82 Operational amplifier 4016 Quad electronic switch 7805 Positive 5 volt regulator 78M12 Positive 12 volt regulator 7815 Positive 15 volt regulator 7915 Negative 15 volt regulator 12.0000 Crystal 12 megahertz

Page 98

OMEGA RACE

Game Board #A084-91372-D929

CHIP NUMBER FUNCTION

7400 Quad 2 input Nand 7402 Quad 2 input Nor 7404 Hex inverter 7407 Hex buffer 7408 Quad 2 input And 7432 Quad 2 input Or 7492 Divide by 12 counter 74138 3 to 8 line decoder 74367 Hex bus driver 74LS373 Octal “D” latch 74LS374 Octal “D” Flip-Flop Z80 CPU 2716 2K x 8 Prom 2114 1K x 4 Ram LM383 8 watt audio amplifier AY-3-8912 Sound chip

Page 99

Vv. SCHEMATICS

Page 100
NOTE > MT 68 WIRING OPTIONS:

Mr 88A. x-FommeR 154 / 60nZ, ard

ont onl r fo Le Fier} - a Lt I am Le | owt camo |

  • pu} MI89 1 13 ro | pp ike: Lod ' POWER SUPPLY PC. | set2-S0413- 8000

conn"c® es

OMEGA RACE U.R. §-29-8 ux. FR,

wie ScHEMATIC ® woSi-00829-R0

STEERING ENCODER 012 9110-Aa00

Om. OmTOH RETURN

Page 101

, SSE WBAWG,

2 Com su, OPERATES. THE 3, SAME AST Cm Sa

OMEGA RACE MINI Sao wx. Saas BN

wiewne sonemare © woS!-008a!-B603

‘STEERING ENCODER 082-910-000

Ld (O-m SWITCH RETURN _]

Page 102
NOTE. ? ML88 WIRING OPTIONS

Mra x Forge 5% / 60 HE,

My ot = Domestic MT Yo= EUROPE OR LK. 89 NOE:

14771
oismeee

WER | wc) RISER | Sal eco a

Legare|al seane sowla

| Ls ae I

suumo-w|e
|Vssysomvet

en ee

i} Lo t _AN45- 00002 - 0000

1.2 We AWG. ‘ NOTES ! 2 sce eoSL INR. COIN om, OPERATES THE “6 Co

wIniNG ScHeMTIC * mo5:-cos%0-BOOS POWER SUPPLY RC, | 082-9045 8000

conn" 70s 1 Tort me TR oy Lo MOTHER BOARD PC sc84 O00T-£829

LOGIC BOARD Pe, nos 21372-0929

sae nore NO. = suiren womuacy NC. = SATCH womans Fy oso 1 PLR, STEERING ENCODER one 9190-4008 |

Page 103

BW YOaWS

DNLYWHIS ONINIM "Os

NOTE = M88 WIRING OPTIONS |

wr, arog 56 0 2

Lame paseo es!

auf cnar « BRN

‘yo | Bees

i}

a3 6 Pos

POWER SUPPLY RC. | J t : | sone- 0818-8000 j

xa] tg \ amer)> | : Pra ied | fe ! oP oa oie i \ Leon ee

  • a oan ty ,

Ls.

a L

TT =As4s-c00e2- 0000 |iTielcw Ia|

. are

J+ut

com | wom. eu ows

y \ JmeibBoG. CN et eri

NOTES! 24 mcawint pooy SNSUL.i‘1ar

OWN, SW. OPERATES THE ale! 3, Sa aos ES Se Jee

OMEGA RACE S.D.

see MK i Sa A

WIRING SCHEMATIC ™ MOSI-C0HS4 BOOK * MOTHER BOARD PC. 084 s0008- £929

LOGIC BOARD RC. os 913t2-0929

NO. = SWITCH NORMALY Seen Nc. TCH woRMALY ‘ttoseo

STEERING ENCODER ‘A0#2= 9180-A000

Page 104

oft"! 2/5/81 LINEAR PWR SUPPLY, 125 VA WITHOUT SUPPORT CIRCUIT MIDWAY MFG. CO. 0I7- 00103-0002 (5 REQ’D) | |

(1_REQ’D) 0945-00808-0200 (| REQ D) 0945-00809-0400 _ _.—, 8-2, 0945- 00808-0100 (2 REQ’D ) OOI7 -00104-0071 (7 REQ’D) = 0945-00809-0200(2REQ’D)

HEAT SINK 0945 - 00806-0000 \ : 0945- 00807-0000 (7 REQ’D) O0I7- 0010-0510 (3 REQ’D)

TIP 3I P.C 8D AO80-90413- D000

HEAT SINK 0068- 058XX—ABDX

Nw LOURRARGES aw) 5. (Ta CER AK 150 0 4700 MF 25 V i

ELECT AX +

MO5I-00929-D003

DO NOT SCALE OWS, ELECT AX OR RADIAL, = JUMPER 4

ASS'Y DRAWING B — FERRITE BEAD WITH 20 GAGE WIRE

PON OMEGA RACE REVISIONS

A082- 90413 -DOO0O0 OMEGA RACE ~ OMIT JUMPER LAND 3 JUMPERS ARE 22 GAGE WIRE

NOTE

co1-

co2-

cos-

co4-

s- Pc

R - JUMPER

F - FUSE CLIP

SPACER 3/8 INCH MOUNT CONN. (MALE)

(FEMALE)

(MALE) 0017-00021-0443 (3 PIN)

0442 (9PIN) 0441 (15 PIN) 0440 (15 PIN)

Page 105

ees veyOg—ayoD_ ere |: es

  • ~ aa - © O12 LOSIC BRO ““< D11 VIDEO DRIVERS sala ¢—ft——. | £9 MISC

te

MT-SO=GORES TIC i MT ~GOmEXPGRT nED p-7! | abt

| «ce ee ke i ss000 NF | neo pl i é mn ewoan a7 470 HF asv

4. 4 “ya e ~ BY

fe ------—- Ke ee an 2 Ff [ £6 -SENSE (12¥) 04 Logic BAD oon 07 VIDEO ORIVERS E12 MISC —<E1 COUNTER DRIVER

iz 2rt4 ‘$V/7. SA ei OS LOGIC BAD DS LOGIC BAD DS GAME BRD 2 AUX. BNO £4 MISC

? = + [” ==470 we 100NF iF bd

16¥ J “08 LO IC BRO

  • . - OF LeeIC BAD ai “510 ORME BRO

-=--=--- 4 hy ne

t PES AUX. ORD PES CONTRELS ~ “Ht PET CORTAGIS ——— ES ATSC mmm 2 SENSE UY)

}

EARTH GND al Fu on ~~ — — pruowa ony TR ~ - nnn BEG COUNTER RTK

try

! ! q------ PR ¥:

j an Or 700 HF wy Co CONTA. LAMPS 7 ——PEIS MUDIE CRT.

ATW. AUX. ¥. BATTERY | y NOT A.C.FAIL “———"~--~<0 Leer Bo ————€ 2 LOBIC #0 Te MONITOR USED RESET <p Logic 6 —— SEE MECH PANEL ALC. SYNC —<D LOSIC BO On X-Y ROUT TER

y RESISTOR KET DIGDE KET

----aq1 ~-- 7! A1-0.i8 OHM, SH R10, A20-150 GHM, 26 01-04-4A1126

2-68 OHR1/2" fli-0. 16 GHM, 1S As- Ai2-6.8 CHM, 1/2K Aé-10 OHM, SH 13-88 OHM, 1/20 95-27 GHM Al4-1.1K GHA AG-270 OHM ALS—47 OHM wee R78. 2K OHM R16-169 OHM > Renin etee AB, A17-100 OHM POT. R16-560 OHH ue JUMPER OR AESISTGR A9-1K OHM 18-47 CHM, 2K OrTion mmm JUMPER GPTIONS amnm FUSE VALUE YRKJES WITH APPLICATION

HOS 1 ~G086S-AU03 den TUK used on RACE MIDHRY HB. COMPROTY FRANKLIN PRR IL.

oat. gvayar | eee 3 PER won | LINER POWER SUPPLY i Pa

{ | Ags: Po dote = 2/27/81 eae H #082-80619-0000

Page 106

E

a a ol =e = a geese

saan “2 TOWAY mre 60.

Page 107

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 108

DESIGNATION LIST CROSS REFERENCE LIST

DESIGNATIONDESCRIPTIONDESIGINATION
ciol-126uF 26V TANTLa6
cistlouF 25V TANT AX,03,4
201lO.uF 25V ELECT AX.Ic Bs
e202, 208ATOUF25V ELECT AX,IC BA
¢ 204-O01uF CER. DISCIc Bs
¢ 2081000 uF 25V ELECT AX.Ic C3
e206-2uF CER. DISCIc cs
e20710 uF 25 ELECT AX.Ic Ds
e208+001 CER. DISCIe ps
c209470 uF 25V ELECT AX.IC £2
2101000 uF 25V ELECT AX.Ic E3
eau-2uF CER. DISCIc F3
cPi-ie-OluF AX.CER. BY PASSIC F4

Ic 63

Ic 68

Rioi-i2668 ohmIe HI
R148~1801KIe He
R201-20747kIo H3
R 208-214tkIc Ha
R215 -220220 ohmIc He
R 221-2301KIe v3
242,24310KIe v4
R250IkIc ue
Res2tkIe KI
R2881k1c K3
R 258-2621k1c ka
R266-2681oKIc KS
R301, 30210kIc ke
R303, 2041kL3,6Hs
R3062.2 ohm43 108
R307220 ohmv4 ics
R308, 3091kks Ics
Rail2.2 ohmka ics
R32220 ohmks Ics
RMI,29 PIN IOK SIPHa Ics
RM3-69 PINIK SIPSWi,2
VR 30810 K POTvt
VR 31010K POTv2

a3 DESCRIPTION

L383

TIP 31

TaLs374

7407

7404 74.8373

T4L8373

T4LS367

T4L8367

7400

74.8367

74.8367

7400

TaLsi3e

74L8374

7408

7402

7432

zeo

7400 soz

2ua

7404

7492

e912

ua

PROM

7404

HEAT SINK

28 PIN IC SOCKET

18 PIN I¢ SOCKET 28 PIN I SOCKET

18 PIN 1¢ SOCKET 24 PIN 1c SOCKET

40 PIN 1¢ SOCKET 8 Pos. DIP KKk-15625 90° (6,15) kK-18628 90° (2,12) KK-18625 90° (2,12) ory

'

N-- PRR - PH RHe-----a-ane DESCRIPTION DESIGNATION

001 uF 50V CER. DISC ¢204, 208

.OluF SOV AX. CER. cPi-i6

+2 uF CER. DISC 206, 211 | uF25V TANT. ciol-126

louF 26V TANT. AX. erst lOuF 25V ELECT. AX. 201, 207 4T0.uF 28V ELECT. AX. ¢202,203,208 1000 uF 28V ELECT. AX. €208, 210

1K 174w 145-150 PART NO.

(0061-O70HX-1AIX

0929-00818-0400

(0929-008!!-0000

0929- 00818-0800 0174- 20864 -EX@x 0929-00808-0800

0929-00808 -1200

0929-00808-1300

(0062-I79B3~ 1 XXX

R22I-230, 250, 208-214, R262, 288, 288-262 R303,304,308,309 2.2 ohm 1/4 W R306, 311 220 ohm 1/4 W R2I5-220 R307, 312 ark aw 201-207

ok vaw R242,243 (0062-034B3~IXXxx (0062-13383 ~1XXx (0062-21183 ~1XXX 0062~22783~IXXx

R266-268, 301, 302 68 ohm 1/4 RIOI-126 1K 9PIN SIP RM3-6

10K 9 PIN SIP RM 1,2 10 K POT VR 308,310

TIP 31 03,4 LM 383 13,6 ‘7400 Ic He,Fa,E2 7402 le He 7404 Ic Ke, J6,B5, 7407 Ie Ba

7408 eH 7432 Ic H3

ra2 Ie KI 7ALsi38 Ie es

7aLsse7 Ic F3,£3,03,D5 74L8373 Ic c3,¢5, TaLs374 Ic 83,65, 24 Ie s4, Ka e912 Ie 33, KB 280 Ic Ha

PROM Ks

HEAT SINK 13,6 HS IB PIN I¢ SOCKET 4, Ka Ics 28 PIN IC SOCKET 43, K3 Ics

24 PIN I SOCKET ks Ics 40 PIN IC SOCKET Ha Ics 8 Pos, DIP sWi,2 (0062-098B3~-1XXx 0929-00820-0100

0062 -00929-0001

(0063~265AX-IEEX

0929-00814-0000

(0066-043BX-xXAX

0929-00810- 3300

0929-00810-3400

0929-00810-3800

0929-00810-3900

0929-00810-3600

0929-00810-3700

0929-00810-3200

0929-00810-1300

0929-00810-2600 (0066~716AX-XXXxx 0929-00810-2300

0929-00810-2800

0066-2898x-xxsx (0066~274BX-XxWD

(0929-00810-3800

0068~-046xx-BXAX

(0069-117XX-XXWX 0069-186xx-xXxWX

0929-00817 -0100

0929-00817 -0200 0929-00816-0000 ary

' DISCRIPTION

Kk-18625 KK-15625,

KK-18625

KK-15625 2 PIN 6 PIN

12 PIN

15 PIN 0) RIOT"

cio7or closgt

DESIGNATION

92,3 at

92,3 a PART NO.

3000-16367-0200 3000-16367-0600

3000-16367-1200

3000-16367-1500

DO NOT SCALE OWG. MO51-00929-G005 PROJ. ENG. J.JARON, Y. BANG

MIDWAY MFG. CO.

Dim TOLERANCE?

seco 20cloare 7721 7 Bl | lA084-91372-G929| ASS'Y DRAWING

DAUGHTER B.D.

Page 109

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.