CATHODE RAY TOMES

Special Project Y (SPY)

S.P.Y.: Special Project Y. (World ver. N) (Konami, 1989) · Manual · 22 pages · 14 sections · original scan

Page 1

od KONAMI"

S.PLY.

Special Project Y

INSTRUCTION MANUAL

fe xonam ® is a trademar! S.P.Y. , n Special Project Y is a registered trademark of Konami, Inc. ©1989 Konami, Inc. Pe imber 857400

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

2 PLAYER S.PY. KIT CONTENTS

Quantity Part # Description 4 857003 SPY. PCB

1857100S.PY. C.PO.
1857101S.PY. Player Instructions
1857200S.PY. Marquee
2857300_—S.PY. Side Decals
1857400S.PY. Manual
230112Blue Button
230110Red Button
230111White Button
130304Red Joy Stick
130305Blue Joy Stick
630250Pal Nuts
630202Switch Holders
140605FCC Cage
140608Kit Box
140904Kit Harness
140310Marquee Plexi
  • * * IMPORTANT NOTICE x x x

The Japanese Amusement Machine Manufacturers Association (JAMMA) has introduced a new standard in video game PCC.B’s. It was decided that all new products from any JAMMA member will use the same pin print-out on the edge connector. The edge connector will have 56 pin outs, 28 per side.

Konami Inc. will offer a 56 to 36 pin adaptor P.C.B. available through your distributor. This new adaptor PC.B. will enable the new 56 pin out to adapt to Konami’s old standard 36 pin out.

Page 4

PUTTING YOUR BEST GAME FORWARD

PREPARATION: For best results, all old graphics should be removed completely from the cabinet. ‘Stick-on’? graphics can be removed by using a hairdryer or hot air device. The heat from the dryer will loosen the adhesive, allowing you to easily peel them off—any adhesive residue can be cleaned off with acetone and a soft dry cloth. (DO NOT USE ACETONE ON SURFACES PAINTED WITH FLAT PAINT.) TOOLS YOU NEED:

  • Foaming Aerosol (such as ‘‘Windex’’).
  • Soft Squeegee.
  • X-Acto Knife. SIDE PANEL DECALS
  • Spray area of cabinet where Side Panel decals are to be applied with foaming aerosol or a mild soap solution.
  • Remove protective backing from decals.
  • Position decals into place.
  • With a soft squeegee, beginning from the center of the decal, slowly and evenly press out excess foam until you achieve a smooth finish.
  • Allow to set approximately 2 to 3 hours before handling. Maximum adherence is achieved in 48 to 72 hours.
  • Trim side decal to fit your cabinet.

CONTROL PANEL OVERLAY: . Refer to Recommended Control Panel Layout. . Drill any new holes needed. . Plug any holes that will not be used. (A permanent epoxy-filler works well for this step.) . Pre-position the overlay prior to removing the backing. . Slowly apply the overlay — inch by inch on the control panel, removing the backing as you apply it. . Once it’s in place, by using an X-Acto knife, cut around the button and joystick placements. INSTRUCTION/BUTTON DECALS: Apply the Player Instruction, Button and 1 Player/2 Player decals in their respective positions. Apply pressure liberally. Allow to set as long as possible before putting game on location. Oo a f wON=

NOTE: Maximum adherence is achieved in 48 to 72 hours.

MARQUEE

(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE)

1/8" Acrylic Marquee should be cut to fit your game. DO NOT remove protective mask until this is done. One way of cutting your Marquee is as follows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish). CUTTING WITH A KNIFE OR SCRIBER: Acrylic sheet up to 3/16” thick may be cut by a method similar to that used for cutting window glass. Use a scriber of some kind — a scribing knife such as the one pictured, a metal scriber, an awl, or even a sturdy craft knife —to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in place. It is best not to remove the protective masking. Make the cuts carefully using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then clamp the acrylic sheet or hold it rigidly under a straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.

Break sheet over edge of table after scribing Always draw the scribing knife along a straight edge.

P.C.B. CAGE INSTALLATION Konami, Inc. now supplies a new style P.C.B. cage which is superior to old style cages because of ease of installation. The cage is made of a 32 point stem-stock which is fire retardant. TO INSTALL THE CAGE:

  • Open cage bottom and secure to desired P.C.B. position. | , ,
  • Install printed circuit board inside cage using wood screws, screwed through the cage bottom into cabinet side.
  • Close the cage over printed circuit board and secure with latch on cage.
Page 5

S.PY. TECHNICAL INFORMATION

S.PY. requires horizontally mounted monitor. It also generates composite negative sync. If your monitor is composite positive sync, you will have to change to composite negative sync.

To alternate composite positive sync to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the output pin from the PC.B. is a combination of H-sync and V-sync.

NOTE: Please refer to Figure 2.

FIGURE 2:

FROM PC. BOARD

NEGATIVE COMPOSITE SYNC. (PIN P on P.C.B. EDGE) (+5V and GND should be taken out of the PC. Board.)

TROUBLE SHOOTING GUIDE

OUTPUT TO MONITOR POSITIVE COMPOSITE SYNC.

PROBLEM: POSSIBLE SOLUTION

No Screen or 1). Check +5V line at the PC.B. Adjust if necessary. Constant Reset 2). Make sure all socketed eproms and custom IC’s are seated securely. Apply light pressure to secure. 3). Check harness to be sure it is not on backwards.

No Sound 1). Check +12V line at the PC.B. 2). Make sure both speaker out wires are connected to the speakers. (DO NOT CONNECT A GROUND.)

Distorted Sound 1). Replace cabinet speaker.

VO Problem (coin 1 1). Do not hook a coin counter to the coin 1 or coin 2 outputs. This doesn’t work or Joystick will cause damage. Up doesn't work, etc.) 2). Check your schematic for the 74LS253 IC that corresponds to your /O problem. Check the appropriate pin with a scope or multimeter for a high output (5V), if output is low replace the 74LS253.

CAUTION

DO NOT WIRE COIN COUNTERS TO THE COIN 1 OR COIN 2 OUTPUTS. THIS WILL CAUSE DAMAGE TO THE I/O MICROCHIP 74LS253. COIN COUNTERS CAN ONLY BE WIRED TO COIN COUNTER OUTPUTS.

Page 6

MONITOR INFORMATION

SERVICE INSTRUCTIONS

NOTE: All monitors are equipped with automatic degaussing coils (L701) which demagnetize the picture tube every time the monitor is turned on after being off for a minimum of 5 minutes. Should any part of the chassis become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move the coil slowly around the CRT face and all surrounding metal parts. Then slowly withdraw for a distance of 6 feet before turning off.

1.0 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished). 2.0 VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This contro! must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions. 3.0 CIRCUIT PROTECTION A 400A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit. 4.0 FOCUS Adjust the focus control, located on the HV unit (1352), for maximum over-all definition and fine picture detail. 5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short. 6.0 HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control. 7.0 VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions ‘‘U” or “D”. 8.0 HORIZONTAL RASTER POSITION ADJUSTMENT If the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper to either positions “R’” or “L’. 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning tool adjustment. This contro! must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions.

  • KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC. USE THE THREE PIN CONNECTOR ON THE MONITOR.

GRN __yg-___ RED DRIVE ORIVE REO CUTOFF GRN CUTOFF’. BLU CUTOFF

*NEG H SYNC *NEG V SYNC.

NOTE: WHEN USING COMPOS: ITE SYNC USE HORIZ. SYNC INPUTS. POS H SYNC: POS V SYNC. HORI, WIDTH Guo [E> con

HORIZ HOLD BLK LEVEL

HORIZ VERT VERT VERT HORIZ CENTERING SIZE HOLD RASTER RASTER SHIFT = SHIFT FIGURE 1

Page 7

S.PY. WIRING DIAGRAM

Solder Side 1————- Parts Side WIRE COLOR KEY:

BLACKeno |_a | 1 | GNDBLACK
BLACKenn]8 | 2 | anoBLACK
RED+svoc|c | 3 | +5vpcRED
RED+svoc]|bp | 4 | +5vocRED
BLUEnotuseD|— | 5 | NoT USEDBLUE
ORANGE+iavoc]F | 6 | +12vDCORANGE

*keY| H | 7 | *KEY

WHITE/REDCOIN COUNTER2{J | 8 | COIN COUNTER 1WHITE/GREEN

(empty)| K | 9 | (EMPTY)

RED/BLACKSPEAKER | L | 10 | SPEAKERRED/YELLOW

(empty) | M_| 11 | (EMPTY)

GREENvioco GREEN]N | 42 | VIDEO REDRED
WHITEvipeo sync | P|13 | VIDEO BLUEBLUE
WHITE/ORANGESERVICE sw|R | 14 | VIDEO GROUNDBLACK
BLACK/WHITE(EMPTY) = 15 | (EMPTY)WHITE/BROWN
BROWN/BLACKconn2|Tt | 16 | con4YELLOW/BLACK
RED/WHITE2p stant]u | 17 | 1P STARTRED
BLUE/WHITE2P UP1P UPBLUE
GREEN/WHITE2p pown|w | 19 | 1P DOWNGREEN
ORANGE/WHITEap Lert|x | 20 | 1p LEFTORANGE
YELLOW/WHITE2priGht|y | 21 | 1P RIGHTYELLOW
BROWN/WHITE2P PUNCH/KICK1P PUNCH/KICKBROWN
VIOLET/WHITE2p KIcK/SHOOT | a | 23 | 1P KICK/SHOOTVIOLET
GRAY/WHITEnot useD|b | 24 | NoT USEDGRAY

not usED| c | 25 | NOT USED not used] a | 26 | Not USED

BLACKand]e | 27 | GNDBLACK
BLACKenp|f | 28 | GNDBLACK

(BASE COLOR/LINE COLOR)

Page 8

DIP SWITCH SETTINGS

DIP SWITCH NO. 1 SETTINGS

  • COIN SWITCH NO. 1 SETTINGS DIP SWITCH NO. 2 SETTINGS
  • THE NUMBER OF PLAYER’S LIFE
sw | 1234 | coin | PLAYsw12NUMBER
o | orF | orF | orF | orF | 11OFF | OFF2
ON12o | oN3
orF | ON13oFF | ON5
ON14ONa
ofr | OFF | ON | OFF | 152 BONUS LIFE
ON1£sw4]5BONUS LIFE
OFF |i ONurOFF | OFF | AT 10,000 PTS AND THEN EVERY 20,000 PTS
oN.1ONAT 20,000 PTS AND THEN EVERY 30,000 PTS
OEE(CRF | OFF)Oh23© |OFF| ON | ar 20,000 PTS ONLY
oNa2ONAT 30,000 PTS ONLY
OFF | ON31

oni 5 A 3. DIFFICULTY OF THE GAME

orr | orF | On | ON34sw | 6ZDIFFICULTY
On41OFF | OFFEASY
‘OrelONri2o | oNNORMAL
ONPREEPERTorF | ONDIFFICULT
FREEPLAY: You can play games without coins.ONVERY DIFFICULT
  • SOUND IN ATTRACTIVE MODE
sw8SOUND

OFF OFF o | ON ON

  • COIN SWITCH NO. 2 SETTINGS ; SWS is not used.
sw | 5678 | coIN | PLAY
°OFF | OFF | OFF | OFF11DIP SWITCH NO. 3 SETTINGS
ON<2ne
orF | ON131. VIDEO SCREEN FLIP
ON14sw1
orr | OFF | on | OFF | 15© | OFFNORMAL
ON16ONUPSIDE DOWN
OFF.ONjii2. CHANGE OF MODE
ON21sw3MODE
OFF | OFF | OFF | ON23oO. | oFFGAME
ONbs2ONTEST
oFF | ON31
an723, CONTINUATION
orr | orF | on | on | 34SWolt
ona7oO | OFFUNLIMITED
oe)TON7:ONFIVE TIMES PER PLAYER
ONVOIDSW2 is not used.

O shows recommended settings.

Page 9

S.PY. TECHNICAL INFORMATION

TECHNICAL INFORMATION GX821-UA SELF TEST

  • Required power capacity Normal: OK will be displayed. Then the game will start. GND-Vecc 5V 4A or more Abnormal: BAD will be displayed and the screen will stop. GND-(+12V) *See the Wiring Diagram.
  • Output oe MANUAL TEST

R (red) analog, positive G (green) analog, positive B (blue) analog, positive SYNC. H-V complexed, negative

  • Use the volume knob on the PCB to adjust sound level. Turn the knob clockwise and it becomes louder.
  • Handle with care. i.
  • How to start Turn on the power while the SW3 of the DIP SWITCH No. 3 is on. Push player 1 START button to change items.
  • Test items ROM check
  • Picture contortion
  • Color check 4.

6. VO check . Sound check Dip switch settings *Push player 1 KICK button to change sound code.

RECOMMENDED CONTROL PANEL LAYOUT

OO 1P START 2P START,

OO BLUE JOYSTICK OO RED JOYSTICK

Page 10

CONTROL PANEL DRILLING TEMPLATE

Button Hole Size 1-3/16 Inch

Use this Template for Player 1 and Player 2 Controls

MOILSAOPL

@

Page 11

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 12

USER INFORMATION

WARNING

F.C.C. REGULATION COMPLIANCE

THIS KIT INTENDED FOR USE ONLY ON COIN-OPERATED VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983 WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH RE- QUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A COMPUTING DEVICE.

IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTERFER- ENCE TO RADIO AND TV. RECEPTION, REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE.

THE PC. BOARD CAGE SUPPLIED WITH THIS CONVERSION KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT THE TIME OF INSTALLATION.

“yp KONAMI

900 Deerfield Parkway, Buffalo Grove, Illinois 60089-4510 Telephone: (312) 215-5100, Telex: 6871385 KONAMI UW, Fax: (312) 215-5122

Page 13

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 14

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 15

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 16

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 17

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 18

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 19

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 20

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 21

JO Cx Co

A |B1CLDLlelLlimLlGiHLiJ1K| L

6X857 053160 oe GX857 053179

PAL20PPAL20P.4 £S138
cerepsast1 iE} NVRAMCS os secg-
12 ie2 165|DIPSH2CS oucy
Tt se |g3COL BES Oy5} tset5 69 v4SOUNDOM Su
ay ine SYP p COLORBK/RVBK4ala 14ade ne 3SOUNODATA Foe
|7PUCBK77 13ale gS
PBK!3/22 313 2y 0 OP BKS.aa 12 NoBICS.2h, Ut3 yler
roo{32a U7oe3=z2 aKa & sa coera 7OUT-FLAG
oe pPBKO,Fe ooTt4SRPCUKE 11) vee fa 915BANK-FLAG
aierLda uss

Y in Lt ABE. pe BF ey

s|RA4. 7KXB:ee

a7 foe

Kitbe180 rc
shar asfAlas earsoon tghe this Parr]a‘som
niRogf) 426)A"4<P reKo 26h27} 6264Wju __#8A ops
=oio aNShas hepe PO 28h—-
|ei a12(20a2 07el} lehie 7inehae109598
vo NESTreser aif!Zhan pelbineBilan cse}28| re
rol!Zino oofbis 35ear0Bom
CLK peeSes “aahZale peltbe oeBaliLe18)
marr“SleeShe soz 03}!8 ses 3Shsa
} __CLKE aemfSher oohba teSharJos186 5)
As}His 15 OF7Ib x17 oFasbool
cutS244|ate fsafte KIS. Ohhheeaishee185590
wtaaosSlag uss«usSloe S64 oehae184
is Leis3
19 Tgves alto feBee vecfe8be veeShee193,58
ADasAyiAy
380 of10hyohoTOMfe AB a
Ls244—cso:
weap KONesepee27512wpe2oy 22{28

ea ‘

19 TrigbsAeo880 a
usveeaALSO4 "
tal?cobaoNAO as
inioa Ze"5
eg2S
ees:e:uy
ooa087

aLso4 | a2, de

es08ia fee02

330 s

AESO8240 ey114fiMED aoe
ec2anv83 meew feoes

-——2atomes ue +

ALS04|a =fl

° --NOTE--

PMC/RVRAMCS _ 1!PMCFIROa4 :
ALSO4Alic50 96 59PBK acseos VCC(+12V)
sod4n ‘S26 10) PBK2pee.1.
aHRIcE Wea? oy U27ne |+ : GND
hg;n5PBKO.:
it;aBS sreiafo a aeoaee cana EDGE 56P
17asfo #28
aei 7]:
os:.ALPHABET: SOLDER SIDE
curtisoe,NUMBER :PARTS SIDE
ae=oewo :64P DIN CONNECTOR
if ENTz22M1wo :64P DIN CONNECTOR
ruurerssa OSCOLOR EK oyme :64P DIN CONNECTOR
ze12[coLonsk /aveK 2wo :64P DIN CONNECTOR
C15 al_is} 051550ipCHA-RD Py,i *1
ize+ashefsSeemo : 4P SV CONNECTOR
aee erya=KINDS OF CAPACITOR
cure4 cornT : TANTALUM

ewe poe COUNTER? M : MYLAR

cant“CoNL_____E : ELECTROL

kaon ute

ownsam SCOUNTERC : CERAMIC

ef KONAMI | conser 5

Page 22

i L

PARTS SIDE [SOLDER SIDE

1 GND A] GNO a en REQUIRED POWER CAPACITY

NOT APPLICABLE2A2a1A+12i5 8yy

c] +5v

15N45WannyanewBBY8.08W7av
peBoD]+5v
ys+87

POWER (5A) =

SUPPLY+12é+12V

F]_+i2v

ND 4 COIN COUNTER 1 {_—— } 8 COIN COUNTER 1 COIN COUNTER 2 J] COIN COUNTER 2

SPEAKER (+) SPEAKER (-)

RED REO GREEN GREEN

COLOUR MONITORBLUEBLUE

SYNC SYNC GND VIDE@ GNO R] SERVICE {jeer f wp stant 7 7 conn if comnt f SERVICE 15 16 COIN 1 T] coin 2 17 1P START

CONTROL FOR 2PUw]2p sTaRT

18 1P UP 2P UP

SAME AS 1P CONTROLS2P DOWN= ¥* ton
a av]2 Dow

20 1P LEFT

2P_PUNCH/KICKX]2 Lert
2P_KICK/SHOOT211P RIGHT

YJ 2P RIGHT 22 1P PUNCH/KICK Z] 2p PUNCH/KICK 23 1P KICK/SHOOT a] 2P KICK/SHOOT

CONTROL FOR 1P bo

a 1p UP

Um FE 1. xickysnootiP DOW£
}OPUNCH/KICKiP _LEFT26 7
tees}———— RIGHTiP RIGHT
LEFT1P_PUNCH/KICK27GND
up1P_KICK/SHOOTe}GND
+EL ___s own28eno

£1] No ~ NOTES -

1 1P 1S NO.1 PLAYER "AMMA S6PIN EDGE CONNECTOR 2P IS NO.2 PLAYER pi8@ INCH-PITCH

2 SURGE KILLER DIODES FOR COIN

COUNTER INSTALLED ON THE P.C.B. fe KONAMI) vonami inoustRY ce..L1o. Fe%-7e| WIRING DIAGRAM DesiGu[_ORAW [CHECK [APPROVE RELEASE] | oq |_ Name | GX857 PWB3515804 ly ‘| ity c TOLE- 1 idle. afl SCALE fanee | A3 [SE ") 351707 T H T T J K L